WinVert1500P A变流器用户使用说明书(常州新誉)资料

24V150W 逆变电源使用说明书
一．简介
该电源采用美国 INTEL 公司 16 位专用微处理芯片控制，主电路采用日本先 进的智能功率 IGBT 模块（IPM），并采用优质环形隔离变压器，具有可靠性高、 高效率、保护功能全、波形失真小、价格低廉等优点。
二．应用
本电源将直流电能转换为 220V，50HZ（或 110V，或 60HZ）交流电能，可 作为邮电、通信、铁路、交通、发电厂等设备的备用电源，也可用于车、船载电 源系统，太阳能或风力发电系统。
8
1
保护功能 输出过载保护 输出短路保护 输入接反保护 输入欠压保护 输入过压保护
过热保护
说明 负载功率超过 120%时，10 秒钟延时后将关断输出 输出万一短路，逆变电源将自动关闭 输入逆变器直流电压极性接反，逆变器将自动保护 输入直流电压低于 21V 时，逆变电源将自动关闭 输入直流电压高于 30V 时，逆变电源将自动关闭 逆变电源机箱内温度超过 75℃时，输出将自动关闭
备注 需关机才能复位
自动复位，即故 障消除后输出将 自动恢复
四．安装步骤及使用方法
1. 开箱时请检查箱体是否有损坏情况，若箱体有明显变形，请立即与供应商联 系。
2. 确认前面板上开关处于“关”位置。 3. 逆变器后面板请按下图接线：
直流输入
交流输出
开 /关
驱动
开关 电源
隔离
接 交流输出 地 直流输入
2
1 6 位微处理器
4、将前面板开关置于“开”位置，即可投入使用。
五．注意事项
1、请勿将直流输入和交流输出接倒； 2、输入直流电压低于 21 VDC 时逆变电源将自动关闭。同时电池电压异常指示灯
常亮，当电池电压恢复至 23VDC 或以上时，逆变电源将再次起动。设置回差 电压是防止系统在欠压点附近振荡。 3、当直流电压高于 30VDC 时，逆变电源将过压保护，此时电池电压异常指示灯 闪烁，同时交流输出将关闭。电池电压即直流输入电压异常时的保护点电压 及回差电压用户可自行调整，如逆变电源应用于太阳能或风力发电场所，由 于电池处于循环使用而不是浮充状态，因此其回差电压必须加大，以防蓄电 池过放电。 4、当输出过载时，过载指示灯亮并关闭输出；当输出短路时，过载指示灯闪烁 并关闭输出。 5、感性负载时请考虑功率因素，非线性负载（如计算机、工控机）时请考虑起 动冲击。带这两种负载时，逆变器均需降额使用。

逆变器用户手册正弦波系列目录一、操作说明 (2)二、产品功能特点 (2)三、适用范围 (3)四、安装指导 (3)五、状态说明 (3)六、技术规格表 (4)*在使用本机前,请仔细阅读本手册所要求的操作方法以及注意事项，否则会造成逆变器的损坏。

请妥善保管好本手册！一．操作说明*本产品在设计和生产时已充分考虑到操作者的安全以及产品的安全使用,避免造成伤害或事故,请严格依照以下说明使用或安装。

（1）安装逆变器时要由专业人士操作，或由当地经销商协助完成。

（2）确认供应直流电源电压范围是否附合要求即+15%，电压极性是否正确。

确认负载电压输入范围是否符合要求即单相220VAC，负载不大于额定功率。

（3）勿将液体流入逆变器内部，或用湿布擦除机器外壳。

机器运行时人体不能直接触及逆变器端子，尤其湿手，否则会造成触电伤害。

（4）正常运行的逆变器如需变动其工作环境，不可自行改变其连线，应由专业人士或经销商确认、操作。

（5）逆变器运行环境应在通风良好、温度范围0至45度环境使用，应远离火源以及日光直射的位置。

不能在结露，灰尘环境下运行。

（6）未成年人不得使用本产品。

（7）确认逆变器地线可靠连接，线径应符合安全使用条件，连接线尽可能缩短。

二．产品功能特点（1）该逆变器使用CPU控制，低成本高品质，智能化正弦波输出，属本产品特有的特点。

（2）本产品逆变输出可负载各类型单相设备，比如马达、空调、电钻、日光灯、气体灯等等家电设备，通信设备，工业设备。

（3）单键智能开关机设计方便操作。

（4）优异的输出短路保护设计，可以抗拒大电流启动负载冲击。

（5）完善的过载保护设计可有效的保护逆变器的安全运行，当负载大于100%~120%时逆变器将于30秒左右自动关机，当负载大于150%逆变器会立即自动关机。

（6）直流供电电路下限保护设计，当直流电源小于标称值的15%，逆变器将自动关闭。

注意:a．未经许可本产品不可以用于维持生命的设备。

b．本逆变器不适宜用于高精密电子设备，需经专业技术人员确认方可投入运行。

WVC-1600(Life)智能微型并网逆变器使用手册微型逆变器的连接器和电缆芯线说明系统组成光伏阵列3-N-零线1-L-火线2-G-地线线端接头注、您可以选购专业定制的带有T 型连接器的交流总线，用此交流总线作为每条支路的交流总线，手拉手连接后构成模块化的微逆变支干线布线系统。

包装清单配件固定螺丝Micro InverterAC 端连接线通讯天线说明书逆变器312-黄&绿-地线(4mm )(4mm )(4mm )微型逆变器的LED 指示功能1.红灯长亮-------------微逆变器上电开机，红灯长亮，设备预备工作状态；2.红灯闪烁-------------微逆变器己全面准备好，进入延时开机状态；3.蓝灯快闪-------------MPPT 最大功率点搜索状态;4.蓝灯长亮-------------MPPT 最大功率点锁定状态;5.蓝灯变为红灯长亮----a.孤岛保护; b.频率保护;c.AC电压过欠压保护; d.DC电压过欠压保护;e.故障; f.软件关机;物联网智能微型逆变器使用手册(433MHz)物联网智能微型逆变器使用手册(433MHz)无线路由器阿里云服务器云智能APPWi-Fi手机控制数据互传双向电表电网开关G物联网智能微型逆变器使用手册(Life)物联网智能微型逆变器使用手册(Life)云智能-物联网监控平台智能物联网监控系统（内置WiFi 数据终端）模组式功能可嵌入智能家居系统独立的一机一密使系统更安全智能移动设备多平台适应（Android /IOS ）使用2.4G 通讯模式和路由器无缝连接每日发电量统计（千瓦时）节能减排环境分析统计实时交流输出电压、电流、功率显示实时直流输入电压、电流、功率显示历史功率曲线查询（日、周、月）逆变器工作环境温度显示实时功率输出调整限制功能远程逆变器启停功能控制性能稳定品质卓越智能物联科创未来数据通讯模式LoRa 通讯协议智能云A PP此二维码用于下载ＡＰＰ手机软件下载以及配网连接使用软件下载请使用二维码扫描下方二维码，安装"云智能"客户端应用程式，智能手机系统运行要求：Android 5.0 、IOS 9 及其以上录入设备启动配网初始化设备设备调节1添加设备2345设置菜单输入功率输出功率系统温度电量图示功能介绍备注：功率调节设备开关云智能APP智能物联网监控系统（内置WiFi 数据终端）模组式功能可嵌入智能家居系统独立的一机一密使系统更安全支持不同平台智能设备（Android /IOS ）超远程通讯模组传输范围可达1公里每日发电量统计（千瓦时）节能减排环境分析统计实时交流输出电压、电流、功率显示实时直流输入电压、电流、功率显示历史功率曲线显示（可查询日、周、月）逆变器工作环境温度显示实时功率输出调整限制功能天气影响电力损失显示远程逆变器启停功能控制●●●●●●●●● 智能APP 在阿里云Iot 物联网的配合下可以实现实时数据的传递及时通过图形和图形显示，用户可以了解电站的运行情况。

ALWAYS READ THESE INSTRUCTIONS BEFORE PROCEEDING Thank you for buying one of our products. For safety and a full understanding of its benefits please read this manual before use. T echnical support is available from 01923 441717 and ******************************.uk.CONTENTS1 Safety Information11.1 Meaning of Symbols and Markings 1 1.2 Precautions 21.3 Safety Advice 42 Introduction 52.1 Inspection 52.2 Description53 Operation63.1 Description of LED Indicators 63.2 Use of Test Prod Shrouds 63.3 Operating Duty Ratio 73.4 Proving Check73.5 T esting for the Presence of Hazardous Live Voltage 93.6 Interference (Phantom) Voltage 94 Maintenance 104.1 Periodic Testing 104.2 Cleaning104.3 Repair and Service 104.4 Storage Conditions 11 5 Warranty 12Specifications2F or further information on measurement categories visit /measurement_categories.phpEquipment complies with relevant EU DirectivesEnd of life disposal of this equipment should be inaccordance with relevant EU Directives1.2 PrecautionsThis product has been designed with your safety in mind, but please pay attention to the following warnings and cautions before use.WarningsIn order to avoid the danger of electrical shock, it is important that proper safety measures are taken when working with voltages exceeding 30V AC rms, 42V AC peak or 60V DC.Where applicable other safety measures such as the use of protective gloves, goggles etc. should be employed.The voltage indicator must only be used by a skilled and competent person who is familiar with the relevant regulations, the safety risks involved and the consequent normal safe working practices.Before each use the voltage indicator should be examined fordamage, cracks, cuts or scratches to the housing, cable and prods. The cable has black outer and contrasting inner insulation, to allow damage to the cable to be easily identified. If there is any doubt the voltage indicator should not be used .Make sure the voltage indicator is dry, clean and free from dust, grease and moisture while in use to avoid the danger from electric shock due to surface leakage.3Before and after each use, the voltage indicator must be proven using a suitable proving device or a known good voltage source. Do not use the voltage indicator if any expected voltage indication LED’s fail to illuminate correctly during proving.Testing for a voltage that exceeds the specified limits of the voltage indicator may damage the voltage indicator and may expose the operator to a shock hazard. Always check the voltage indicators specified limits before use.The voltage indicator must only be used on installations up to 1000V to earth, and within the operating temperature and humidity range specified.Always keep your fingers behind the finger guards. Never touch the exposed metal prod tips.Do not use the voltage indicator during rain or precipitation.The different indicating signals of the voltage detector (including the ELV limit indication) are not to be used for measuring purposes.The voltage indicator must not be dismantled or modified in any way by unauthorized persons. The safety of the voltage indicator cannot be guaranteed under such circumstances and must not be used .CautionsAvoid severe mechanical shock or vibration and extreme temperature.If the voltage indicator has been stored or transported in temperatures outside its normal operating range it should be given sufficient time to stabilise in the environment where it is to be used. An acclimatisation time of at least 2 hours is required prior to operation of the voltage indicator.52. INTRODUCTION2.1 InspectionExamine the shipping carton for any sign of damage. Inspect the unit and any accessories for damage. If there is any damage then consult your distributor immediately.2.2 DescriptionThe Martindale VI-15000 is a development of the VI13700 which is widely specified to ensure the electrical safety of users when proving dead i.e. not hazardous live. It is constructed in accordance with the latest safety standards.The voltage tester has the following features:Tests for DC and AC Voltage up to 1000VAutomatic AC/DC detection Bright LED indicationFull voltage indication function without batteries P rotective resistor in probe to limit current in the event of cable damageContrasting colour of inner sheath to highlight cable damage Ergonomic and robust housing R etractable shroudsMeets fully GS38 and BS EN61243-3:2014 Measurement category CA T IV 1000VVoltage thresholds7If desired, and before the unit is connected to any source of voltage,the shrouds can be locked back by pushing and twisting 90°.The prod tips will be exposed by 3 ± 0.5mm. In this position they areGS38 compliant.3.3 Operating Duty RatioThe voltage indicator should be operated (ON) for a maximum periodof 30 seconds. This should be followed by a recovery period (OFF) of4 minutes.The operating duty ratio is 8 to 1, so if the voltage indicator is onlyON for 2 seconds then the OFF period need only be 16 seconds.3.4 Proving CheckBefore each use the voltage indicator should be examined fordamage, cracks, cuts or scratches to the housing, cable and prods.The cable has black outer and contrasting inner insulation, to allowdamage to the cable to be easily identified. If there is any doubt thevoltage indicator should not be used.Before and after use, verify the voltage indicator is functioningcorrectly with a proving device (PD690, PD700 or PD710 is8recommended), or a known good voltage source. Do not use thevoltage indicator if any expected voltage indication LED’s (50, 120,230, 400, 690V) fail to illuminate correctly during proving.The LED’s that illuminate during proving will depend on themagnitude of the proving unit output or the voltage source. Seetable 1.Table 1. Required LED indications during provingVI-15000LED’sVoltagesource230V 50HzProving unit typePD430 orPD440PD690 orPD700PD710+ 50V On On On Only + or -On*- 50V On On On120V On On On On230V On On On On400V Off On On On690V Off Off On On* Illumination of the 50V polarity LED’s depends on the polarity ofthe connections to the PD710. Always reverse the connections tothe PD710 to check the other 50V LED.W arningI f the proving device or voltage source exceeds the specifiedlimits of the voltage indicator the voltage indicator may bedamaged and the operator may be exposed to a shock hazard.Always check the specification of the proving device or thevoltage magnitude of the voltage source before proceeding witha proving check.9During this verification emphasis should also be placed uponthe flexing of the voltage indicator’s cable along its length, andparticularly at the entry points to the hand held elements, to confirmthat the cable has not been fractured.Any unexpected display should be investigated and the VI-15000not used unless all expected voltage indication LED’s illuminate.3.5 Testing for the Presence of Hazardous Live VoltageW arningH old the voltage indicator and test prod behind the fingerguards in a manner that will not obscure the voltage indicationLED’s. Never touch the exposed metal test prods or any part ofthe voltage indicator forward of the finger guards while appliedto hazardous voltages.While taking all required safety precautions connect both test prodsto the UUT (Unit or location under test).The polarity and voltage level of any voltage present will beindicated by the illumination of the voltage indicator LED’s.3.6 Interference (Phantom) VoltageIt is possible for wiring that is ‘dead’ to indicate the apparentpresence of voltage at power frequency.If wiring that is live is running in close proximity to the ‘dead’ wiringbeing tested, there can be capacitive or inductive coupling betweenthe two, thereby causing interference (phantom) voltages.R efer to section 1.3 for safety advice relevant to interferencevoltage.104. MAINTENANCE4.1 Periodic TestingTo maintain the integrity of the voltage indicator, Martindale Electricrecommends that it is returned at least once a year to verify physicalintegrity, electrical specification and insulation integrity.Martindale Electric is pleased to offer you this service. Pleasecontact our Service Department for details.Email:******************************.ukTel: 01923 6506604.2 CleaningWarningTo reduce the risk of surface leakage, this instrument must be kept ina clean condition.WarningPrior to cleaning, ensure that the instrument is disconnected fromany voltage source.If contamination is found, clean with a damp soft cloth and ifnecessary a mild detergent or alcohol. Do not use abrasives,abrasive solvents, or detergents which can cause damage to theunit. If a mild detergent is used, the unit should subsequently bethoroughly cleaned with a water dampened soft cloth. After cleaning,dry and allow to remain in a dry environment for 2 hours before use.4.3 Repair and ServiceThere are no user serviceable parts in this unit. Return to MartindaleElectric if faulty. Our service department will quote promptly to repairany fault that occurs outside the guarantee period.EnvironmentalTemperature & Humidity (Operating & Storage): -10°C to 55°CAltitude: up to 2000mPollution degree 2Martindale Electric Company Limited。