液压方面的英文词汇

柱塞泵: plunger pump | ram pump | Piston Pumps多柱塞泵: multi plunger pump | multiple-plunger pump隔膜柱塞泵: diaphragm plungerpump液压气压传动：Fluid power drives液压传动：Hydraulic power drive气压传动；pneumatic power drive静液压传动、容积式液压传动：Hydrostatic power drive动液压传动：Hydrodynamic power drive容积泵：Positive-displacement pump叶片泵：Impeller-type pump容积式液压马达：Hydraulic actuator叶片式液压马达：Impeller-type Hydraulic motor液压管路：Hydraulic line , line吸入管路：I ntake line排出管路、压力管路：pressure line回流管路：Return line排（疏）液管路：Drain line泵：Pump（泵的）流量、排量：Pump capacity液压马达：Hydraulic motor定（恒）量泵：Constant-displacement pump恒速液压马达：Constant-speed hydraulic motor变量泵：Variable-displacement pump变速液压马达：Variable-speed hydraulick泵-马达：Pump-motor压缩机：Air compressor气压马达：Pneumatic motor真空泵：Vacuum pump风机：Fan齿轮泵：Gear pump齿轮式液压马达：Gear-type hydraulic motor转子泵、回转式泵：Rotary abutment pump转子式液压马达、回转式液压马达：Rotary abutment motor 螺杆泵：Screw pump螺杆式液压马达：Screw motor滑片泵：Vane pump滑片式液压马达：V ane motor轴向活塞泵：Axial-piston pump轴向活塞式液压马达：Axial-piston motor气压缸：pneumatic cylinder活塞：Piston活塞杆：Piston rod单（向）作用缸、单动缸：Single-acting cylinder双（向）作用缸、双动缸：Double-acting cylinder活塞腔、活塞侧：head end of cylinder活塞杆腔、活塞杆侧：Rod end of cylinder柱塞缸：Plunger cylinder伸缩缸、套筒式缸：Telescoping cylinder隔膜作动缸：Diaphragm actuator摆动式液压机、摆动式液压马达、摆动油缸：Limited rotary Hydraulic motor滑片式摆动液压机、滑片式摆动液压马达、滑片式摆动油缸：Vane-type limited rotary motor 活塞式摆动液压机、活塞式摆动液压马达、活塞式摆动油缸：Piston-type limited rotary motor 液压变换器、换压器：Hydraulic transformer液压控制阀：Hydraulic control valve滑阀：Spool valve Slide valve液压开关、旋塞（阀）：Rotary valve阀门、阀：Seat valve压力（控制）阀：Pressure control valve定差减压阀：Relief valve安全阀：Safety valve减压阀：Pressure reducing valve单向阀：Check valve节流阀：Throttle节流：throttling工作孔：oriffice分配阀：distribution valve液压分配阀、配液阀：Hydraulic distribution valve气压分配阀、配气阀：pneumatic distribution valve（液压）蓄压器：Hydraulic accumulator重锤蓄压器：Weighted hydraulic accumulator弹簧蓄压器：Spring-loaded hydraulic accumulator管路、管道：pipeline管子：Pipe接管零件、管件：Pipe fitting管节：Pipe coupling弯头：Elbow三通管：Tee四通管：cross管堵（塞）、外丝堵、螺塞：Male pipe plug堵盖：Bonnet鞍形接头、交叉接头：Cross-over(saddle)内接头、螺纹接头：Shoulder nipple接管螺母、接头螺母：Collar nut旋入接头：Threaded bushing中间接头：Union joint接管：Union nipple软管：Hose轴向柱塞泵: axial plunger pump一、阀类Solenoid valve 电磁阀Check valve 单向阀Cartridge valve 插装阀Sandwich plate valve 叠加阀Pilot valve 先导阀Pilot operated check valve 液控单向阀Sub-plate mount 板式安装Manifold block 集成块Pressure relief valve 压力溢流阀Flow valve 流量阀Throttle valve 节流阀Double throttle check valve 双单向节流阀Rotary knob 旋钮Rectifier plate 节流板Servo valve 伺服阀Proportional valve 比例阀Position feedback 位置反馈Progressive flow 渐增流量De-energizing of solenoid 电磁铁释放二、介质类Phosphate ester (HFD-R) 磷酸甘油酯Water-glycol (HFC) 水-乙二醇Emulsion 乳化液Inhibitor缓蚀剂Synthetic lubricating oil 合成油三、液压安装工程Contamination 污染Grout 灌浆Failure 失效Jog 点动Creep爬行Abrasion 摩擦Retract（活塞杆）伸出Extension （活塞杆）缩回Malfunction 误动作Pickling 酸洗Flushing 冲洗Dipping process 槽式酸洗Re-circulation 循环Passivity 钝化Nitric acid 柠檬酸Argon 氩气Butt welding 对接焊Socket welding 套管焊Inert gas welding 惰性气体焊四、管接头Bite type fittings 卡套式管接头Tube to tube fittings 接管接头union 直通接管接头union elbow 直角管接头union tee 三通管接头union cross 四通管接头Mal stud fittings 端直通管接头Bulkhead fittings 长直通管接头Weld fittings 焊接式管接头Female connector fittings 接头螺母Reducers extenders 变径管接头Banjo fittings 铰接式管接头Adjustable fittings/swivel nut 旋转接头五、伺服阀及伺服系统性能参数Dynamic response 动态频响DDV-direct drive valve 直动式伺服阀NFPA-National Fluid Power Association 美国流体控制学会Phase lag 相位滞后Nozzle flapper valve 喷嘴挡板阀Servo-jet pilot valve 射流管阀Dither 颤振电流Coil impedance 线圈阻抗Flow saturation 流量饱和Linearity 线形度Symmetry 对称性Hysterics 滞环Threshold 灵敏度Lap 滞后Pressure gain 压力增益Null 零位Null bias 零偏Null shift 零飘Frequency response 频率响应Slope 曲线斜坡。

液压专业英语词汇acceptable conditions许用工况actual conditions实际工况actual force实际输出力air contamination空气污染air consumption耗气量air conditioner unit空气处理单元air filter空气过滤器adjustable restrictive valve可调节流阀amplifier放大器amplitude ratio幅值比analogue amplifier模拟放大器anti-corrosive quality抗腐蚀性automatic cycle自动循环axial piston pump轴向柱塞泵back pressure背压bladder accumulator气囊式蓄能器bleed line放气管路bonded washer组合垫圈breakout pressure启动压力butterfly valve蝶阀cartridge valve插装阀cavitation气穴charge pressure充油压力check valve单向阀circle循环circuit diagram回路图clamper管卡closed circuit闭式回路collapse pressure压溃压力compensator避震喉composite seal复合密封件continuous working conditions连续工况control of pump泵的控制control console操作台control panel控制屏cooler冷却器counterbalance valve平衡阀cracking pressure开启压力cushioning缓冲cylinder缸cycling speed循环速度De-energizing of solenoid 电磁铁释放density密度diaphragm valve膜片阀differential circuit差动回路differential cylinder差动缸differential pressure instrument压差计digital amplifier数字放大器direction of rotation旋转方向directly operated type直动式displacement排量dither颤振double-acting cylinder双作用缸Double throttle check valve 双单向节流阀drain line泄油管路drift漂移drive shaft coupling联轴器dwell phase停止工步duplex filter双筒过滤器efficiency效率effective filtration area有效过滤面积elastomer seal弹性密封件elbow弯头electrical pressure transducer压力传感器external leakage外泄漏extend stroke外伸行程filter pressure drop过滤器压降fitting；connection接头fixed restrictive valve固定节流阀flared fitting扩口式接头flash point闪点flexible hose软管flange connection法兰接头flange mounting法兰安装flow-combining valve集流阀flow control valve流量控制阀flow control circuit调速回路flow divider valve分流阀flow gain流量增益flow limit流量极限flow line管路flow meter流量计flow pass流道flow rate流量Flow valve 流量阀flower factor流量系数foot mounting底座安装force输出力four-way valve四通阀free position自由位frequency response频率响应function diagram功能图gate valve闸阀gear pump齿轮泵global(ball) valve球阀graphical symbol图形符号heat exchanger热交换器heater加热器hydraulic lock液压锁紧hydraulic motor液压马达hydraulic power流体传动hydraulics液压技术hydrodynamics液力技术hydropneumatics气液技术hysteresis滞环hydraulic amplifier液压放大器hydraulic controlled type液控式instantaneous conditions瞬态工况internal leakage内泄漏inlet pressure进口压力induced pressure负载压力kinematic viscosity运动粘度laminar flow层流lap遮盖leakage泄漏limited conditions极限工况linearity线性度linear region线性区liquid contamination液体污染liquid level measuring instrument液位计lubricator油雾气manually operated type手动式manifold block油路块mechanically controlled type机械控制式mechanical seal机械密封meter-in circuit进口节流回路meter-out circuit出口节流回路Manifold block 集成块needle valve针阀neutral position中位nitrile butadiene rubber；NBR丁腈橡胶noise level噪声等级nominal filtration rating公称过滤精度nominal pressure公称压力nozzle flapper喷嘴挡板null bias零偏null drift零漂null(quiescent) leakage零位内泄漏one-way restrictive valve单向节流阀opening开口open circuit开式回路operating conditions运行工况operating pressure运行压力outlet pressure出口压力over lap正遮盖override pressure调压偏差override control优先控制packing seal填料密封peak pressure峰值压力phase工步phase lag相位移Pilot valve 先导阀pilot pressure控制压力pilot-controlled check valve液控单向阀pilot-operated type先导式Pilot operated check valve 液控单向阀piston pump柱塞泵pilot line控制管路pipe-work管路布置piston seal活塞密封polytetrafluoroethene；PTFE聚四氟乙烯poppet valve锥阀portable particle counter便携式颗粒检测仪port油口Position feedback 位置反馈power station液压泵站pre-charge pressure充气压力pressure control circuit压力控制回路pressure drop；differential pressure压降pressure gauge压力表Pressure relief valve 压力溢流阀pressure switch压力开关pressure time diagram压力－时间图pressure relief valve压力控制阀pressure relief valve溢流阀pressure reducing valve减压阀Progressive flow 渐增流量Proportional valve 比例阀proof pressure耐压试验压力pulse generator脉冲发生器quick release coupling快换接头radial seal径向密封rapid advance phase快进工步rapid return phase快退工步rated conditions额定工况rated flow额定流量rated pressure额定压力rear end无杆端Rectifier plate 节流板reducer fitting异径接头replenishing line补液管路reservoir fluid capacity油箱容量resolution分辨率retract stroke内缩行程return line回油管路repeat ability重复性reproducibility复现性rigid tube硬管ripple波动rod end有杆端rod seal活塞杆密封rotary seal旋转密封Rotary knob 旋钮rust protection防锈性safety circuit安全回路sandwich valve叠加阀Sandwich plate valve 叠加阀sealed reservoir闭式油箱sensor传感器sequence valve顺序阀servo-valve伺服阀shut-off valve截止阀shuttle valve梭阀silencer消声器single-acting cylinder单作用缸slide valve滑阀solid contamination固体颗粒污染Solenoid valve 电磁阀speed regulator valve调速阀static pressure静压力sticking液压卡紧steady-state conditions稳态工况stiffness刚度sub-plate底板sub-plate valve板式阀Sub-plate mount 板式安装suction pressure吸入压力supply flow供给流量surge pressure冲击压力system pressure系统压力symbols for hydraulic and pneumatic components液压气动元件图形符号symbols for fluid logic devices流体逻辑元件图形符号symbols for logic functions逻辑功能图形符号symmetry对称度synchronizing circuit同步回路telescopic cylinder伸缩缸thermostat温度控制器threshold阈值Throttle valve 节流阀transfer function传递函数turbulent flow紊流under lap负遮盖unloading valve卸荷阀valve阀valve element阀芯valve element position阀芯位置variable displacement pump变量泵valve pressure drop阀压降valve polarity阀极性viscosity粘度 water content含水量welded fitting焊接式接头 wiper seal；scraper防尘圈密封working cycle工作循环 working pressure工作压力working phase工作工步 working stroke工作行程working line工作管路 vane pump叶片泵zero position零位 zero lap零遮盖一．阀类分流阀 flow divider valve 截止阀 shut-off valve球阀 global(ball) valve 针阀 needle valve闸阀 gate valve 膜片阀 diaphragm valve蝶阀 butterfly valve 阀 valve底板 sub-plate 油路块 manifold block 板式阀sub-plate valve 叠加阀 sandwich valve 插装阀 cartridge valve 滑阀 slide valve 锥阀 poppet valve 阀芯valve element 阀芯位置 valve element position单向阀 check valve液控单向阀 pilot-controlled check valve梭阀 shuttle valve压力控制阀 pressure relief valve溢流阀 pressure relief valve顺序阀 sequence valve减压阀 pressure reducing valve平衡阀 counterbalance valve卸荷阀 unloading valve流量控制阀 flow control valve方向控制阀（directional valve）液压辅件（accessory）普通阀（common valve）Solenoid valve 电磁阀Check valve 单向阀Cartridge valve 插装阀Sandwich plate valve 叠加阀Pilot valve 先导阀Pilot operated check valve 液控单向阀Sub-plate mount 板式安装Manifold block 集成块Rotary knob 旋钮Rectifier plate 节流板Servo valve 伺服阀Proportional valve 比例阀Position feedback 位置反馈Progressive flow 渐增流量De-energizing of solenoid 电磁铁释放固定节流阀 fixed restrictive valve可调节流阀 adjustable restrictive valve单向节流阀 one-way restrictive valve调速阀 speed regulator valve分流阀 flow divider valve集流阀 flow-combining valveDDV-direct drive valve 直动式伺服阀二、介质类Phosphate ester (HFD-R) 磷酸甘油酯 Water-glycol (HFC) 水-乙二醇Emulsion 乳化液 Inhibitor缓蚀剂 Synthetic lubricating oil 合成油三、液压安装工程Abrasion 摩擦 Argon 氩气 Butt welding 对接焊Contamination 污染 Creep爬行 Dipping process 槽式酸洗Extension （活塞杆）缩回 Failure 失效Flushing 冲洗 Grout 灌浆 Inert gas welding 惰性气体焊Jog 点动 Malfunction 误动作 Nitric acid 柠檬酸Passivity 钝化 Pickling 酸洗 Retract（活塞杆）伸出Re-circulation 循环 Socket welding 套管焊四、管接头Adjustable fittings/swivel nut 旋转接头Banjo fittings 铰接式管接头Bite type fittings 卡套式管接头Bulkhead fittings 长直通管接头Female connector fittings 接头螺母Mal stud fittings 端直通管接头Reducers extenders 变径管接头Tube to tube fittings 接管接头union 直通接管接头union elbow 直角管接头union tee 三通管接头union cross 四通管接头Weld fittings 焊接式管接头五、伺服阀及伺服系统性能参数Dynamic response 动态频响DDV-direct drive valve 直动式伺服阀NFPA-National Fluid Power Association 美国流体控制学会Phase lag 相位滞后Nozzle flapper valve 喷嘴挡板阀Servo-jet pilot valve 射流管阀 Dither 颤振电流Coil impedance 线圈阻抗Flow saturation 流量饱和Linearity 线形度 Symmetry 对称性Hysterics 滞环 Threshold 灵敏度Lap 滞后Pressure gain 压力增益Null 零位Null bias 零偏Null shift 零飘Frequency response 频率响应Slope 曲线斜坡。

液压专业英语词汇流体传动hydraulic power液压技术hydraulics液力技术hydrodynamics气液技术hydropneumatics 运行工况operating conditions额定工况rated conditions极限工况limited conditions瞬态工况instantaneous conditions稳态工况steady-state conditions许用工况acceptable conditions 连续工况continuous working conditions实际工况actual conditions效率efficiency旋转方向direction of rotation公称压力nominal pressure工作压力working pressure 进口压力inlet pressure出口压力outlet pressure压降pressure drop；differential pressure背压back pressure启动压力breakout pressure充油压力charge pressure开启压力cracking pressure 峰值压力peak pressure运行压力operating pressure耐压试验压力proof pressure冲击压力surge pressure静压力static pressure系统压力system pressure控制压力pilot pressure 充气压力pre-charge pressure吸入压力suction pressure调压偏差override pressure额定压力rated pressure耗气量air consumption泄漏leakage内泄漏internal leakage 外泄漏external leakage层流laminar flow紊流turbulent flow气穴cavitation流量flow rate 排量displacement额定流量rated flow供给流量supply flow流量系数flower factor滞环hysteresis图形符号graphical symbol液压气动元件图形符号symbols for hydraulic and pneumatic components流体逻辑元件图形符号symbols for fluid logic devices逻辑功能图形符号symbols for logic functions 回路图circuit diagram压力－时间图pressure time diagram功能图function diagram循环circle 自动循环automatic cycle工作循环working cycle循环速度cycling speed工步phase 停止工步dwell phase工作工步working phase快进工步rapid advance phase快退工步rapid return phase频率响应frequency response重复性repeat ability复现性reproducibility漂移drift波动ripple线性度linearity线性区linear region液压锁紧hydraulic lock液压卡紧sticking变量泵variable displacement pump 泵的控制control of pump齿轮泵gear pump叶片泵vane pump柱塞泵piston pump轴向柱塞泵axial piston pump法兰安装flange mounting底座安装foot mounting液压马达hydraulic motor刚度stiffness中位neutral position零位zero position 自由位free position缸cylinder有杆端rod end无杆端rear end外伸行程extend stroke内缩行程retract stroke缓冲cushioning工作行程working stroke负载压力induced pressure输出力force实际输出力actual force单作用缸single-acting cylinder双作用缸double-acting cylinder 差动缸differential cylinder伸缩缸telescopic cylinder阀valve底板sub-plate油路块manifold block 板式阀sub-plate valve叠加阀sandwich valve插装阀cartridge valve滑阀slide valve 锥阀poppet valve阀芯valve element阀芯位置valve element position单向阀check valve液控单向阀pilot-controlled check valve梭阀shuttle valve压力控制阀pressure relief valve 溢流阀pressure relief valve顺序阀sequence valve减压阀pressure reducing valve平衡阀counterbalance valve卸荷阀unloading valve直动式directly operated type先导式pilot-operated type机械控制式mechanically controlled type手动式manually operated type液控式hydraulic controlled type流量控制阀flow control valve固定节流阀fixed restrictive valve可调节流阀adjustable restrictive valve单向节流阀one-way restrictive valve 调速阀speed regulator valve分流阀flow divider valve集流阀flow-combining valve截止阀shut-off valve球阀global(ball) valve针阀needle valve闸阀gate valve膜片阀diaphragm valve 蝶阀butterfly valve噪声等级noise level放大器amplifier模拟放大器analogue amplifier数字放大器digital amplifier传感器sensor阈值threshold伺服阀servo-valve四通阀four-way valve 喷嘴挡板nozzle flapper液压放大器hydraulic amplifier颤振dither阀极性valve polarity流量增益flow gain对称度symmetry流量极限flow limit零位内泄漏null(quiescent) leakage遮盖lap 零遮盖zero lap正遮盖over lap负遮盖under lap开口opening零偏null bias零漂null drift阀压降valve pressure drop分辨率resolution频率响应frequency response幅值比amplitude ratio 相位移phase lag传递函数transfer function管路flow line硬管rigid tube软管flexible hose工作管路working line回油管路return line补液管路replenishing line控制管路pilot line泄油管路drain line放气管路bleed line接头fitting；connection焊接式接头welded fitting 扩口式接头flared fitting快换接头quick release coupling法兰接头flange connection弯头elbow异径接头reducer fitting流道flow pass油口port闭式油箱sealed reservoir 油箱容量reservoir fluid capacity气囊式蓄能器bladder accumulator空气污染air contamination 固体颗粒污染solid contamination液体污染liquid contamination空气过滤器air filter 油雾气lubricator热交换器heat exchanger冷却器cooler加热器heater温度控制器thermostat 消声器silencer双筒过滤器duplex filter过滤器压降filter pressure drop有效过滤面积effective filtration area公称过滤精度nominal filtration rating压溃压力collapse pressure 填料密封packing seal机械密封mechanical seal径向密封radial seal旋转密封rotary seal活塞密封piston seal活塞杆密封rod seal防尘圈密封wiper seal；scraper组合垫圈bonded washer 复合密封件composite seal弹性密封件elastomer seal丁腈橡胶nitrile butadiene rubber；NBR聚四氟乙烯polytetrafluoroethene；PTFE优先控制override control压力表pressure gauge 压力传感器electrical pressure transducer压差计differential pressure instrument 液位计liquid level measuring instrument流量计flow meter压力开关pressure switch脉冲发生器pulse generator液压泵站power station空气处理单元air conditioner unit压力控制回路pressure control circuit安全回路safety circuit差动回路differential circuit调速回路flow control circuit进口节流回路meter-in circuit出口节流回路meter-out circuit 同步回路synchronizing circuit开式回路open circuit闭式回路closed circuit管路布置pipe-work 管卡clamper联轴器drive shaft coupling操作台control console控制屏control panel 避震喉compensator粘度viscosity运动粘度kinematic viscosity密度density 含水量water content闪点flash point防锈性rust protection抗腐蚀性anti-corrosive quality便携式颗粒检测仪portable particle counterSolenoid valve 电磁阀Check valve 单向阀Cartridge valve 插装阀Sandwich plate valve 叠加阀Pilot valve 先导阀Pilot operated check valve 液控单向阀Sub-plate mount 板式安装Manifold block 集成块Pressure relief valve 压力溢流阀Flow valve 流量阀Throttle valve 节流阀Double throttle check valve 双单向节流阀Rotary knob 旋钮Rectifier plate 节流板Servo valve 伺服阀Proportional valve 比例阀Position feedback 位置反馈Progressive flow 渐增流量De-energizing of solenoid 电磁铁释放液压英文资料流体传动hydraulic power液压技术hydraulics液力技术hydrodynamics 气液技术hydropneumatics运行工况operatingconditions额定工况ratedconditions 极限工况limitedconditions瞬态工况instantaneous conditions 稳态工况steady-state conditions许用工况acceptableconditions 连续工况continuousworking conditions实际工况actualconditions 效率 efficiency旋转方向directionof rotation公称压力nominalpressure 工作压力workingpressure进口压力inletpressure出口压力outletpressure 压降 pressure drop；differentialpressure背压 back pressure启动压力breakoutpressure充油压力chargepressure开启压力crackingpressure 峰值压力peakpressure运行压力operatingpressure耐压试验压力proofpressure 冲击压力surgepressure静压力staticpressure系统压力systempressure 控制压力pilotpressure充气压力pre-chargepressure吸入压力suctionpressure 调压偏差overridepressure额定压力ratedpressure耗气量 air consumption 泄漏 leakage内泄漏 internal leakage外泄漏 external leakage 层流 laminar flow紊流 turbulent flow气穴 cavitation流量 flow rate排量 displacement额定流量 rated flow供给流量 supply flow流量系数 flower factor 滞环 hysteresis图形符号graphical symbol 液压气动元件图形符号symbols for hydraulic and pneumatic components 流体逻辑元件图形符号symbols for fluid logic devices 逻辑功能图形符号 symbols for logic functions回路图 circuit diagram 压力－时间图pressure time diagram功能图 function diagram 循环 circle自动循环 automatic cycle工作循环 working cycle循环速度 cycling speed 工步 phase停止工步 dwell phase工作工步 working phase快进工步 rapid advance phase 快退工步rapid return phase频率响应frequency responseHysterics 滞环Threshold 灵敏度Lap 滞后Pressure gain 压力增益Null 零位Null bias 零偏Null shift 零飘Frequency response 频率响应Slope 曲线斜坡液压系统（hydraulic system）执行元件（actuator）液压缸（cylinder）液压马达（motor）液压回路（circuit）压力控制回路（pressurecontrol）流量（速度）控制回路（speedcontrol）方向控制回路（directionalvalve control）安全回路（securitycontrol）定位回路（positioncontrol）同步回路（synchronisecircuit）顺序动作回路（sequeuntcircuit）液压泵（pump）阀（valve）压力控制阀（pressurevalve）、流量控制阀（flow valve）方向控制阀（directionalvalve）液压辅件（accessory）普通阀（commonvalve）插装阀（cartridge valve）叠加阀（superimposedvalve四、管接头Bite type fittings 卡套式管接头Tube to tube fittings 接管接头union 直通接管接头 union elbow 直角管接头union tee 三通管接头union cross 四通管接头Mal stud fittings 端直通管接头Bulkhead fittings 长直通管接头Weld fittings 焊接式管接头Female connector fittings 接头螺母Reducers extenders 变径管接头Banjo fittings 铰接式管接头Adjustable fittings/swivel nut 旋转接头五、伺服阀及伺服系统性能参数Dynamic response 动态频响DDV-direct drive valve 直动式伺服阀NFPA-National Fluid Power Association 美国流体控制学会Phase lag 相位滞后Nozzle flapper valve 喷嘴挡板阀Servo-jet pilot valve 射流管阀Dither 颤振电流Coil impedance 线圈阻抗Flow saturation 流量饱和Linearity 线形度Symmetry 对称性Throttle valve 节流阀Double throttle check valve 双单向节流阀Rotary knob 旋钮Rectifier plate 节流板Servo valve 伺服阀Proportional valve 比例阀Position feedback 位置反馈Progressive flow 渐增流量De-energizing of solenoid 电磁铁释放二、介质类Phosphate ester (HFD-R) 磷酸甘油酯Water-glycol (HFC) 水-乙二醇Emulsion 乳化液Inhibitor缓蚀剂Synthetic lubricating oil 合成油三、液压安装工程Contamination 污染Grout 灌浆Failure 失效Jog 点动Creep爬行Abrasion 摩擦Retract（活塞杆）伸出Extension （活塞杆）缩回Malfunction 误动作Pickling 酸洗Flushing 冲洗Dipping process 槽式酸洗Re-circulation 循环Passivity 钝化Nitric acid 柠檬酸Argon 氩气Butt welding 对接焊Socket welding 套管焊Inert gas welding 惰性气体焊空气处理单元air conditioner unit压力控制回路pressurecontrol circuit 安全回路safety circuit差动回路differential circuit调速回路flowcontrol circuit 进口节流回路 meter-incircuit出口节流回路 meter-outcircuit同步回路synchronizing circuit 开式回路opencircuit闭式回路closedcircuit管路布置pipe-work 管卡clamper联轴器drive shaft coupling操作台control console 控制屏control panel避震喉compensator粘度viscosity 运动粘度kinematicviscosity密度density 含水量water content闪点flash point防锈性rust protection 抗腐蚀性anti-corrosive quality便携式颗粒检测仪portableparticle counter Solenoid valve 电磁阀Check valve单向阀Cartridge valve插装阀Sandwich plate valve叠加阀Pilot valve先导阀Pilot operated check valve液控单向阀Sub-plate mount板式安装Manifold block集成块Pressure relief valve压力溢流阀Flow valve 流量阀冷却器cooler加热器heater温度控制器 thermostat消声器silencer双筒过滤器 duplexfilter 过滤器压降filterpressure drop有效过滤面积effectivefiltration area 公称过滤精度 nominalfiltration rating压溃压力 collapsepressure填料密封 packingseal 机械密封 mechanicalseal径向密封 radialseal旋转密封 rotaryseal活塞密封 pistonseal 活塞杆密封rod seal防尘圈密封wiper seal；scraper组合垫圈bondedwasher 复合密封件 compositeseal弹性密封件 elastomerseal丁腈橡胶 nitrilebutadiene rubber；NBR 聚四氟乙烯polytetrafluoroethene；PTFE优先控制 overridecontrol压力表 pressure gauge 压力传感器electricalpressure transducer压差计differential pressure instrument 液位计liquid level measuring instrument流量计flow meter压力开关pressure switch 脉冲发生器 pulse generator液压泵站 power station遮盖lap零遮盖zero lap正遮盖over lap 负遮盖under lap开口opening零偏null bias零漂null drift阀压降valve pressure drop 分辨率resolution频率响应 frequencyresponse幅值比amplitude ratio相位移phase lag 传递函数transferfunction管路flow line硬管rigid tube软管flexible hose工作管路 workingline回油管路 returnline补液管路replenishing line控制管路 pilot line 泄油管路 drain line放气管路 bleed line接头fitting；connection焊接式接头 welded fitting 扩口式接头 flared fitting快换接头 quick release coupling法兰接头 flange connection 弯头elbow异径接头 reducer fitting流道flow pass油口port闭式油箱 sealed reservoir 油箱容量reservoir fluid capacity气囊式蓄能器bladder accumulator 空气污染 air contamination固体颗粒污染 solid contamination液体污染 liquid contamination 空气过滤器 air filter油雾气lubricator热交换器 heat exchanger分流阀flow divider valve 集流阀 flow-combining valve截止阀shut-off valve球阀global(ball) valve 针阀needle valve闸阀gate valve膜片阀diaphragm valve蝶阀butterfly valve 噪声等级noise level放大器amplifier模拟放大器analogue amplifier 数字放大器digital amplifier传感器sensor阈值threshold伺服阀servo-valve 四通阀four-way valve喷嘴挡板nozzle flapper液压放大器hydraulic amplifier 颤振dither阀极性valve polarity流量增益 flow gain对称度symmetry流量极限 flow limit 零位内泄漏null(quiescent) leakage重复性repeat ability复现性reproducibility 漂移drift波动ripple线性度linearity线性区linear region液压锁紧 hydrauliclock 液压卡紧sticking变量泵variable displacement pump泵的控制control ofpump 齿轮泵gear pump叶片泵vane pump柱塞泵piston pump轴向柱塞泵axialpiston pump 法兰安装flangemounting底座安装footmounting液压马达hydraulicmotor 刚度stiffness中位neutral position零位zero position自由位free position缸cylinder 有杆端rod end无杆端rear end外伸行程extend stroke内缩行程retract stroke 缓冲cushioning工作行程working stroke负载压力induced pressure输出力force 实际输出力 actual force单作用缸 single-acting cylinder双作用缸 double-acting cylinder 差动缸differential cylinder伸缩缸telescopic cylinder阀valve底板sub-plate 油路块manifold block板式阀sub-plate valve叠加阀sandwich valve插装阀cartridge valve 滑阀slide valve锥阀poppet valve阀芯valve element阀芯位置 valve element position 单向阀check valve液控单向阀pilot-controlled check valve梭阀shuttle valve 压力控制阀pressure relief valve溢流阀pressure relief valve顺序阀sequence valve 减压阀pressure reducing valve平衡阀counterbalance valve卸荷阀unloading valve 直动式directly operated type先导式pilot-operated type 机械控制式mechanically controlled type手动式manually operated type 液控式hydraulic controlled type流量控制阀flow control valve 固定节流阀fixed restrictive valve可调节流阀adjustable restrictive valve 单向节流阀 one-way restrictive valve调速阀speed regulator valve。

Aability 性能；能力load-carrying ability 承载能力absorber 吸收器；吸收剂；过滤器；减震器accessories 辅件，附件，配件hydraulic accessories 液压辅件accumulate 储存；蓄能；累积accumulator 蓄能器；蓄电池；累加器accuracy 准确性；精度action 作用；动作；作用力；行程actuated 操纵，控制directly actuated 直接操纵的，直接控制的pilot actuated 先导控制的，液控的actuator 执行元件；液压缸；马达adapter 接头；衬套；压环；连接件pipe adapter 管接头admission 供给，供油，供气alignment 找正，定心，对中amplifier 放大器differential pressure amplifier 压差放大器flow amplifier 流量放大器assembly 组合，组件，机组axis 轴Bback-flow 回流back-up 支撑hydrostatic back-up 静压支撑barrel 桶，缸体base 底座；支座bearing 支承；轴承；方位radial ball bearing 径向球轴承rolling bearing 滚动轴承sliding bearing 滑动轴承thrust bearing 止推轴承bed 台pump test bed 泵实验台behavior 性能；工况bend 弯头；弯管blade 叶片flat blade 平面叶片forward inclined blade 前倾叶片guide blade 导叶radial blade 径向叶片bleed 排气air bleed 排气阀bleeder 排气孔block 块；封闭；块体cartridge valve block 插装阀块体choke block 节流板directional control block 多路阀/方向控制阀组panel block 阀板组body 体；缸筒；阀体，壳体pump body 泵体tank body 箱体valve body 阀体bolt 螺栓；插销；螺杆boss 轮毂bottom 底；底部cylinder bottom 缸底；缸后盖bracket 支架pump bracket 泵架bubble-tight 气密的buffer 缓冲器，阻尼器bush(ing> 套，导向套；衬套b5E2RGbCAPCcap 帽,盖,罩,塞cylinder end cap 缸端盖cylinder head cap 缸前盖capacity 容量。

WORD格式液压专业常用英语词汇Abrasion摩擦Retract（活塞杆）缩回一、阀类Extension（活塞杆）伸出Solenoidvalve电磁阀Malfunction误动作Checkvalve单向阀Pickling酸洗Cartridgevalve插装阀Flushing冲洗Sandwichplatevalve叠加阀Dippingprocess槽式酸洗Pilotvalve先导阀Re-circulation循环Pilotoperatedcheckvalve液控单向阀Passivity钝化Sub-platemount板式安装Nitricacid柠檬酸Manifoldblock集成块Argon氩气Pressurereliefvalve压力溢流阀Buttwelding对接焊Flowvalve流量阀Socketwelding套管焊Throttlevalve节流阀Inertgaswelding惰性气体焊Doublethrottlecheckvalve双单向节流阀Rotaryknob旋钮四、管接头Rectifierplate节流板Bitetypefittings卡套式管接头Servovalve伺服阀Tubetotubefittings接管接头Proportionalvalve比例阀union直通接管接头Positionfeedback位置反馈unionelbow直角管接头Progressiveflow渐增流量uniontee三通管接头De-energizingofsolenoid电磁铁释放unioncross四通管接头Malstudfittings端直通管接头二、介质类Bulkheadfittings长直通管接头Phosphateester(HFD-R)磷酸甘油酯Weldfittings焊接式管接头Water-glycol(HFC)水-乙二醇Femaleconnectorfittings接头螺母Emulsion乳化液Reducersextenders变径管接头Inhibitor缓蚀剂Banjofittings铰接式管接头Syntheticlubricatingoil合成油WORD格式Adjustablefittings/swivelnut旋转接头三、液压安装工程五、伺服阀及伺服系统性能参数Contamination污染Dynamicresponse动态频响Grout灌浆DDV-directdrivevalve直动式伺服阀Failure失效NFPA-NationalFluidPowerAssociation美Jog点动国流体控制学会Creep爬行WORD格式瞬态工况instantaneousconditionsPhaselag相位滞后稳态工况steady-stateconditionsNozzleflappervalve喷嘴挡板阀许用工况acceptableconditionsServo-jetpilotvalve射流管阀连续工况continuousworkingconditionsDither颤振电流实际工况actualconditionsCoilimpedance线圈阻抗效率efficiencyFlowsaturation流量饱和旋转方向directionofrotationLinearity线形度公称压力nominalpressureSymmetry对称性工作压力workingpressureHysterics滞环进口压力inletpressureThreshold灵敏度出口压力outletpressureLap滞后压降pressuredrop；differentialpressurePressuregain压力增益背压backpressureNull零位启动压力breakoutpressureNullbias零偏充油压力chargepressureNullshift零飘开启压力crackingpressureFrequencyresponse频率响应峰值压力peakpressureSlope曲线斜坡运行压力operatingpressure 六、密封材质代号耐压试验压力proofpressure 冲击压力surgepressureNR天然橡胶静压力staticpressureNBR丙烯晴-丁二醛-橡胶系统压力systempressureCR氯丁二烯-橡胶WORD格式控制压力pilotpressureFPM氟橡胶充气压力pre-chargepressurePUR聚氨酯吸入压力suctionpressurePTFE聚四氟乙烯调压偏差overridepressurePA聚酰胺、尼龙额定压力ratedpressureB棉织物耗气量airconsumptionA耐高温织物流体传动hydraulicpower泄漏leakage液压技术hydraulics内泄漏internalleakage液力技术hydrodynamics外泄漏externalleakage气液技术hydropneumatics层流laminarflow运行工况operatingconditions紊流turbulentflow额定工况ratedconditions气穴cavitation极限工况limitedconditions流量flowrate排量displacement执行元件actuator额定流量ratedflow液压缸cylinder供给流量supplyflow液压马达motor流量系数flowerfactor液压回路circuit滞环hysteresis压力控制回路pressurecontrol图形符号graphicalsymbol流量（速度）控制回路speedcontrol液压气动元件图形符号symbolsfor方向控制回路directionalvalvecontrol 安全回路securitycontrolhydraulicandpneumaticcomponents流体逻辑元件图形符号symbolsforfluid定位回路positioncontrol同步回路synchronisecircuitlogicdevices逻辑功能图形符号symbolsforlogic顺序动作回路sequeuntcircuit液压泵pumpfunctions回路图circuitdiagram阀valve压力－时间图pressuretimediagram压力控制阀pressurevalve功能图functiondiagram流量控制阀flowvalve循环circle方向控制阀directionalvalve自动循环automaticcycle液压辅件accessory工作循环workingcycle空气处理单元airconditionerunit循环速度cyclingspeed压力控制回路pressurecontrolcircuit工步phase安全回路safetycircuit停止工步dwellphase差动回路differentialcircuit工作工步workingphase调速回路flowcontrolcircuit快进工步rapidadvancephase进口节流回路meter-incircuit快退工步rapidreturnphase出口节流回路meter-outcircuit频率响应frequencyresponse同步回路synchronizingcircuit滞环Hysterics开式回路opencircuit灵敏度Threshold闭式回路closedcircuit滞后Lap管路布置pipe-work压力增益Pressuregain管卡clamper零位Null联轴器driveshaftcoupling零偏Nullbias操作台controlconsole零飘Nullshift控制屏controlpanel频率响应Frequencyresponse避震喉compensator曲线斜坡Slope粘度viscosity七、液压系统（hydraulicsystem）运动粘度kinematicviscosity密度density聚四氟乙烯polytetrafluoroethene；PTFE含水量watercontent优先控制overridecontrol闪点flashpoint压力表pressuregauge防锈性rustprotection压力传感器electricalpressuretransducer抗腐蚀性anti-corrosivequality压差计differentialpressureinstrument便携式颗粒检测仪portableparticlecounter液位计liquidlevelmeasuringinstrument 电磁阀Solenoidvalve流量计flowmeter插装阀Cartridgevalve压力开关pressureswitch叠加阀Sandwichplatevalve脉冲发生器pulsegenerator液压泵站powerstation先导阀Pilotvalve液控单向阀Pilotoperatedcheckvalve遮盖lap板式安装Sub-platemount零遮盖zerolap集成块Manifoldblock正遮盖overlap压力溢流阀Pressurereliefvalve负遮盖underlap流量阀Flowvalve开口opening冷却器cooler零偏nullbias加热器heater零漂nulldrift温度控制器thermostat阀压降valvepressuredrop消声器silencer分辨率resolution双筒过滤器duplexfilter频率响应frequencyresponse过滤器压降filterpressuredrop幅值比amplituderatio有效过滤面积effectivefiltrationarea相位移phaselag公称过滤精度nominalfiltrationrating传递函数transferfunction压溃压力collapsepressure管路flowline填料密封packingseal硬管rigidtube机械密封mechanicalseal软管flexiblehose径向密封radialseal工作管路workingline旋转密封rotaryseal回油管路returnline活塞密封pistonseal补液管路replenishingline活塞杆密封rodseal控制管路pilotline防尘圈密封wiperseal；scraper泄油管路drainline组合垫圈bondedwasher放气管路bleedline复合密封件compositeseal接头fitting；connection弹性密封件elastomerseal焊接式接头weldedfitting丁腈橡胶nitrilebutadienerubber；NBR扩口式接头flaredfittingWORD格式快换接头quickreleasecouplingfrequencyresponse频率响应法兰接头flangeconnectionfunctiondiagram功能图弯头elbowgatevalve闸阀异径接头reducerfittinggearpump齿轮泵流道flowpassglobal(ball)valve球阀油口portgraphicalsymbol图形符号闭式油箱sealedreservoirheatexchanger热交换器油箱容量reservoirfluidcapacityheater加热器气囊式蓄能器bladderaccumulatorhydrauliclock液压锁紧空气污染aircontaminationhydraulicmotor液压马达固体颗粒污染solidcontaminationhydraulicpower流体传动液体污染liquidcontaminationhydraulics液压技术空气过滤器airfilterhydrodynamics液力技术油雾器lubricatorhydropneumatics气液技术hysteresis滞环分流阀flowdividervalvehydraulicamplifier液压放大器集流阀flow-combiningvalvehydrauliccontrolledtype液控式截止阀shut-offvalveinstantaneousconditions瞬态工况球阀global(ball)valveinternalleakage内泄漏针阀needlevalveinletpressure进口压力闸阀gatevalveinducedpressure负载压力膜片阀diaphragmvalvekinematicviscosity运动粘度蝶阀butterflyvalvelaminarflow层流噪声等级noiselevelWORD格式leakage泄漏放大器amplifierlimitedconditions极限工况模拟放大器analogueamplifierlinearity线性度数字放大器digitalamplifierlinearregion线性区传感器sensorliquidcontamination液体污染阈值thresholdliquidlevelmeasuringinstrument液位计伺服阀servo-valvemanuallyoperatedtype手动式四通阀&nbsmanifoldblock油路块mechanicallycontrolledtype机械控制式force输出力neutralposition中位four-wayvalve四通阀nitrilebutadienerubber；NBR丁腈橡胶freeposition自由位液压专业词汇流体传动hydraulicpower泄漏leakage液压技术hydraulics内泄漏internalleakage液力技术hydrodynamics外泄漏externalleakage气液技术hydropneumatics层流laminarflow运行工况operatingconditions紊流turbulentflow额定工况ratedconditions气穴cavitation极限工况limitedconditions流量flowrate瞬态工况instantaneousconditions排量displacement稳态工况steady-stateconditions额定流量ratedflow许用工况acceptableconditions供给流量supplyflow连续工况continuousworkingconditions流量系数flowerfactor实际工况actualconditions滞环hysteresis效率efficiency图形符号graphicalsymbol旋转方向directionofrotation液压气动元件图形符号symbolsfor公称压力nominalpressurehydraulicandpneumaticcomponents 工作压力workingpressure流体逻辑元件图形符号symbolsforfluid进口压力inletpressurelogicdevices出口压力outletpressure逻辑功能图形符号symbolsforlogic压降pressuredrop；differentialpressurefunctions背压backpressure回路图circuitdiagram启动压力breakoutpressure压力－时间图pressuretimediagram充油压力chargepressure功能图functiondiagram开启压力crackingpressure循环circle峰值压力peakpressure自动循环automaticcycle运行压力operatingpressure工作循环workingcycle耐压试验压力proofpressure循环速度cyclingspeed冲击压力surgepressure工步phase静压力staticpressure停止工步dwellphase系统压力systempressure工作工步workingphase控制压力pilotpressure快进工步rapidadvancephase充气压力pre-chargepressure快退工步rapidreturnphase吸入压力suctionpressure频率响应frequencyresponse调压偏差overridepressure重复性repeatability额定压力ratedpressure复现性reproducibility耗气量airconsumption漂移drift波动ripple板式阀sub-platevalve线性度linearity叠加阀sandwichvalve线性区linearregion插装阀cartridgevalve液压锁紧hydrauliclock滑阀slidevalve液压卡紧sticking锥阀poppetvalve变量泵variabledisplacementpump阀芯valveelement泵的控制controlofpump阀芯位置valveelementposition齿轮泵gearpump单向阀checkvalve叶片泵vanepump液控单向阀pilot-controlledcheckvalve柱塞泵pistonpump梭阀shuttlevalve轴向柱塞泵axialpistonpump压力控制阀pressurereliefvalve 法兰安装flangemounting溢流阀pressurereliefvalve底座安装footmounting顺序阀sequencevalve液压马达hydraulicmotor减压阀pressurereducingvalve刚度stiffness平衡阀counterbalancevalve中位neutralposition卸荷阀unloadingvalve零位zeroposition直动式directlyoperatedtype自由位freeposition先导式pilot-operatedtype缸cylinder机械控制式mechanicallycontrolledtype有杆端rodend手动式manuallyoperatedtype无杆端rearend液控式hydrauliccontrolledtype外伸行程extendstroke流量控制阀flowcontrolvalve内缩行程retractstroke固定节流阀fixedrestrictivevalve 缓冲cushioning可调节流阀adjustablerestrictivevalve工作行程workingstroke单向节流阀one-wayrestrictivevalve 负载压力inducedpressure调速阀speedregulatorvalve输出力force分流阀flowdividervalve实际输出力actualforce集流阀flow-combiningvalve单作用缸single-actingcylinder截止阀shut-offvalve双作用缸double-actingcylinder球阀global(ball)valve差动缸differentialcylinder针阀needlevalve伸缩缸telescopiccylinder闸阀gatevalve阀valve膜片阀diaphragmvalve底板sub-plate蝶阀butterflyvalve油路块manifoldblock噪声等级noiselevel放大器amplifier泄油管路drainline模拟放大器analogueamplifier放气管路bleedline数字放大器digitalamplifier接头fitting；connection传感器sensor焊接式接头weldedfitting阈值threshold扩口式接头flaredfitting伺服阀servo-valve快换接头quickreleasecoupling四通阀four-wayvalve法兰接头flangeconnection喷嘴挡板nozzleflapper弯头elbow液压放大器hydraulicamplifier异径接头reducerfitting颤振dither流道flowpass阀极性valvepolarity油口port流量增益flowgain闭式油箱sealedreservoir对称度symmetry油箱容量reservoirfluidcapacity流量极限flowlimit气囊式蓄能器bladderaccumulator零位内泄漏null(quiescent)leakage空气污染aircontamination遮盖lap固体颗粒污染solidcontamination零遮盖zerolap液体污染liquidcontamination正遮盖overlap空气过滤器airfilter负遮盖underlap油雾气lubricator开口opening热交换器heatexchanger零偏nullbias冷却器cooler零漂nulldrift加热器heater阀压降valvepressuredrop温度控制器thermostat分辨率resolution消声器silencer频率响应frequencyresponse双筒过滤器duplexfilter幅值比amplituderatio过滤器压降filterpressuredrop相位移phaselag有效过滤面积effectivefiltrationarea传递函数transferfunction公称过滤精度nominalfiltrationrating 管路flowline压溃压力collapsepressure硬管rigidtube填料密封packingseal软管flexiblehose机械密封mechanicalseal工作管路workingline径向密封radialseal回油管路returnline旋转密封rotaryseal补液管路replenishingline活塞密封pistonseal控制管路pilotline活塞杆密封rodseal防尘圈密封wiperseal；scraper便携式颗粒检测仪portableparticlecounter 组合垫圈bondedwasher复合密封件compositeseal弹性密封件elastomerseal优先控制overridecontrol压力表pressuregauge压力传感器electricalpressuretransducer压差计differentialpressureinstrument液位计liquidlevelmeasuringinstrument流量计flowmeter压力开关pressureswitch脉冲发生器pulsegenerator液压泵站powerstation空气处理单元airconditionerunit压力控制回路pressurecontrolcircuit安全回路safetycircuit差动回路differentialcircuit调速回路flowcontrolcircuit进口节流回路meter-incircuit出口节流回路meter-outcircuit同步回路synchronizingcircuit开式回路opencircuit闭式回路closedcircuit管路布置pipe-work管卡clamper联轴器driveshaftcoupling操作台controlconsole控制屏controlpanel粘度viscosity运动粘度kinematicviscosity密度density含水量watercontent闪点flashpoint防锈性rustprotection抗腐蚀性anti-corrosivequality。

液压专业常用英语词汇一、阀类Solenoidvalve电磁阀Checkvalve单向阀Cartridgevalve插装阀Sandwichplatevalve叠加阀Pilotvalve先导阀Pilotoperatedcheckvalve液控单向阀Sub-platemount板式安装Manifoldblock集成块Pressurereliefvalve压力溢流阀Flowvalve流量阀Throttlevalve节流阀Doublethrottlecheckvalve双单向节流阀Rotaryknob旋钮Rectifierplate节流板Servovalve伺服阀Proportionalvalve比例阀Positionfeedback位置反馈Progressiveflow渐增流量De-energizingofsolenoid电磁铁释放二、介质类Phosphateester(HFD-R)磷酸甘油酯Water-glycol(HFC)水-乙二醇Emulsion乳化液Inhibitor缓蚀剂Syntheticlubricatingoil合成油三、液压安装工程Contamination污染Grout灌浆Failure失效Jog点动Creep爬行Abrasion摩擦Retract（活塞杆）缩回Extension（活塞杆）伸出Malfunction误动作Pickling酸洗Flushing冲洗Dippingprocess槽式酸洗Re-circulation 循环Passivity 钝化Nitricacid柠檬酸Argon氩气Buttwelding对接焊Socketwelding 套管焊Inertgaswelding惰性气体焊四、管接头Bitetypefittings卡套式管接头Tubetotubefittings 接管接头union 直通接管接头unionelbow直角管接头uniontee三通管接头unioncross四通管接头Malstudfittings端直通管接头Bulkheadfittings长直通管接头Weldfittings焊接式管接头Femaleconnectorfittings接头螺母Reducersextenders变径管接头Banjofittings铰接式管接头Adjustablefittings/swivelnut旋转接头五、伺服阀及伺服系统性能参数Dynamicresponse动态频响DDV-directdrivevalve直动式伺服阀NFPA-NationalFluidPowerAssociation 美国流体控制学会Phaselag相位滞后Nozzleflappervalve喷嘴挡板阀Servo-jetpilotvalve射流管阀Dither颤振电流Coilimpedance线圈阻抗Flowsaturation流量饱和Linearity线形度Symmetry对称性Hysterics滞环Threshold灵敏度Lap滞后Pressuregain压力增益Null零位Nullbias零偏Nullshift零飘Frequencyresponse频率响应Slope曲线斜坡六、密封材质代号NR天然橡胶NBR丙烯晴-丁二醛-橡胶CR氯丁二烯-橡胶FPM氟橡胶PUR聚氨酯PTFE聚四氟乙烯PA聚酰胺、尼龙B棉织物A耐高温织物流体传动hydraulicpower液压技术hydraulics液力技术hydrodynamics气液技术hydropneumatics运行工况operatingconditions额定工况ratedconditions极限工况limitedconditions瞬态工况instantaneousconditions 稳态工况steady-stateconditions许用工况acceptableconditions连续工况continuousworkingconditions实际工况actualconditions效率efficiency 旋转方向directionofrotation公称压力nominalpressure工作压力workingpressure进口压力inletpressure出口压力outletpressure压降pressuredrop；differentialpressure背压backpressure启动压力breakoutpressure充油压力chargepressure开启压力crackingpressure峰值压力peakpressure运行压力operatingpressure耐压试验压力proofpressure冲击压力surgepressure静压力staticpressure系统压力systempressure控制压力pilotpressure充气压力pre-chargepressure吸入压力suctionpressure调压偏差overridepressure额定压力ratedpressure耗气量airconsumption泄漏leakage内泄漏internalleakage外泄漏externalleakage层流laminarflow紊流turbulentflow气穴cavitation流量flowrate排量displacement额定流量ratedflow供给流量supplyflow流量系数flowerfactor滞环hysteresis图形符号graphicalsymbol液压气动元件图形符号symbolsforhydraulicandpneumaticcom ponents流体逻辑元件图形符号symbolsforfluidlogicdevices逻辑功能图形符号symbolsforlogicfunctions回路图circuitdiagram压力－时间图pressuretimediagram 功能图functiondiagram 循环circle自动循环automaticcycle工作循环workingcycle循环速度cyclingspeed工步phase停止工步dwellphase工作工步workingphase快进工步rapidadvancephase快退工步rapidreturnphase频率响应frequencyresponse滞环Hysterics灵敏度Threshold滞后Lap压力增益Pressuregain零位Null零偏Nullbias零飘Nullshift频率响应Frequencyresponse曲线斜坡Slope七、液压系统（hydraulicsystem）执行元件actuator液压缸cylinder液压马达motor液压回路circuit压力控制回路pressurecontrol流量（速度）控制回路speedcontrol 方向控制回路directionalvalvecontrol安全回路securitycontrol定位回路positioncontrol同步回路synchronisecircuit顺序动作回路sequeuntcircuit液压泵pump阀valve压力控制阀pressurevalve流量控制阀flowvalve方向控制阀directionalvalve液压辅件accessory空气处理单元airconditionerunit压力控制回路pressurecontrolcircuit 安全回路safetycircuit差动回路differentialcircuit调速回路flowcontrolcircuit进口节流回路meter-incircuit出口节流回路meter-outcircuit同步回路synchronizingcircuit 开式回路opencircuit闭式回路closedcircuit管路布置pipe-work管卡clamper联轴器driveshaftcoupling操作台controlconsole控制屏controlpanel避震喉compensator粘度viscosity运动粘度kinematicviscosity密度density含水量watercontent闪点flashpoint防锈性rustprotection抗腐蚀性anti-corrosivequality便携式颗粒检测仪portableparticlecounter电磁阀Solenoidvalve插装阀Cartridgevalve叠加阀Sandwichplatevalve先导阀Pilotvalve液控单向阀Pilotoperatedcheckvalve板式安装Sub-platemount集成块Manifoldblock压力溢流阀Pressurereliefvalve流量阀Flowvalve冷却器cooler加热器heater温度控制器thermostat消声器silencer双筒过滤器duplexfilter过滤器压降filterpressuredrop有效过滤面积effectivefiltrationarea公称过滤精度nominalfiltrationrating压溃压力collapsepressure填料密封packingseal机械密封mechanicalseal径向密封radialseal旋转密封rotaryseal活塞密封pistonseal活塞杆密封rodseal防尘圈密封wiperseal；scraper组合垫圈bondedwasher 复合密封件compositeseal弹性密封件elastomerseal丁腈橡胶nitrilebutadienerubber；NBR 聚四氟乙烯polytetrafluoroethene；PTFE优先控制overridecontrol压力表pressuregauge压力传感器electricalpressuretransducer压差计differentialpressureinstrume nt液位计liquidlevelmeasuringinstrume nt流量计flowmeter压力开关pressureswitch脉冲发生器pulsegenerator液压泵站powerstation遮盖lap零遮盖zerolap正遮盖overlap负遮盖underlap开口opening零偏nullbias零漂nulldrift阀压降valvepressuredrop 分辨率resolution频率响应frequencyresponse幅值比amplituderatio相位移phaselag传递函数transferfunction管路flowline硬管rigidtube软管flexiblehose工作管路workingline回油管路returnline补液管路replenishingline控制管路pilotline泄油管路drainline放气管路bleedline接头fitting；connection 焊接式接头weldedfitting扩口式接头flaredfitting快换接头quickreleasecoupling 法兰接头flangeconnection 弯头elbow异径接头reducerfitting流道flowpass油口port闭式油箱sealedreservoir油箱容量reservoirfluidcapacity 气囊式蓄能器bladderaccumulator 空气污染aircontamination固体颗粒污染solidcontamination 液体污染liquidcontamination空气过滤器airfilter油雾器lubricator分流阀flowdividervalve集流阀flow-combiningvalve 截止阀shut-offvalve球阀global(ball)valve针阀needlevalve闸阀gatevalve膜片阀diaphragmvalve蝶阀butterflyvalve噪声等级noiselevel放大器amplifier模拟放大器analogueamplifier 数字放大器digitalamplifier 传感器sensor阈值threshold伺服阀servo-valve四通阀&nbsforce输出力four-wayvalve四通阀freeposition自由位frequencyresponse频率响应functiondiagram功能图gatevalve闸阀gearpump齿轮泵global(ball)valve球阀graphicalsymbol图形符号heatexchanger热交换器heater加热器hydrauliclock液压锁紧hydraulicmotor液压马达hydraulicpower流体传动hydraulics液压技术hydrodynamics液力技术hydropneumatics气液技术hysteresis滞环hydraulicamplifier液压放大器hydrauliccontrolledtype液控式instantaneousconditions瞬态工况internalleakage内泄漏inletpressure进口压力inducedpressure负载压力kinematicviscosity运动粘度laminarflow层流leakage泄漏limitedconditions极限工况linearity线性度linearregion线性区liquidcontamination液体污染liquidlevelmeasuringinstrument液位计manuallyoperatedtype手动式manifoldblock油路块mechanicallycontrolledtype机械控制式neutralposition中位nitrilebutadienerubber；NBR丁腈橡胶液压专业词汇流体传动hydraulicpower液压技术hydraulics液力技术hydrodynamics气液技术hydropneumatics运行工况operatingconditions额定工况ratedconditions极限工况limitedconditions瞬态工况instantaneousconditions 稳态工况steady-stateconditions许用工况acceptableconditions连续工况continuousworkingconditions实际工况actualconditions效率efficiency旋转方向directionofrotation公称压力nominalpressure工作压力workingpressure进口压力inletpressure出口压力outletpressure压降pressuredrop；differentialpressure背压backpressure 启动压力breakoutpressure 充油压力chargepressure开启压力crackingpressure 峰值压力peakpressure运行压力operatingpressure 耐压试验压力proofpressure 冲击压力surgepressure静压力staticpressure系统压力systempressure控制压力pilotpressure充气压力pre-chargepressure 吸入压力suctionpressure调压偏差overridepressure 额定压力ratedpressure耗气量airconsumption泄漏leakage内泄漏internalleakage外泄漏externalleakage层流laminarflow紊流turbulentflow气穴cavitation流量flowrate排量displacement额定流量ratedflow供给流量supplyflow流量系数flowerfactor滞环hysteresis图形符号graphicalsymbol液压气动元件图形符号symbolsforhydraulicandpneumaticcom ponents流体逻辑元件图形符号symbolsforfluidlogicdevices逻辑功能图形符号symbolsforlogicfunctions回路图circuitdiagram压力－时间图pressuretimediagram 功能图functiondiagram循环circle自动循环automaticcycle工作循环workingcycle循环速度cyclingspeed工步phase停止工步dwellphase工作工步workingphase快进工步rapidadvancephase 快退工步rapidreturnphase频率响应frequencyresponse重复性repeatability复现性reproducibility漂移drift波动ripple线性度linearity线性区linearregion液压锁紧hydrauliclock液压卡紧sticking变量泵variabledisplacementpump 泵的控制controlofpump齿轮泵gearpump叶片泵vanepump柱塞泵pistonpump轴向柱塞泵axialpistonpump法兰安装flangemounting底座安装footmounting液压马达hydraulicmotor刚度stiffness中位neutralposition零位zeroposition自由位freeposition缸cylinder有杆端rodend无杆端rearend外伸行程extendstroke内缩行程retractstroke缓冲cushioning工作行程workingstroke负载压力inducedpressure输出力force实际输出力actualforce单作用缸single-actingcylinder 双作用缸double-actingcylinder 差动缸differentialcylinder 伸缩缸telescopiccylinder阀valve底板sub-plate油路块manifoldblock板式阀sub-platevalve叠加阀sandwichvalve插装阀cartridgevalve滑阀slidevalve锥阀poppetvalve阀芯valveelement 阀芯位置valveelementposition单向阀checkvalve液控单向阀pilot-controlledcheckvalve梭阀shuttlevalve压力控制阀pressurereliefvalve溢流阀pressurereliefvalve顺序阀sequencevalve减压阀pressurereducingvalve平衡阀counterbalancevalve卸荷阀unloadingvalve直动式directlyoperatedtype先导式pilot-operatedtype机械控制式mechanicallycontrolledtype手动式manuallyoperatedtype液控式hydrauliccontrolledtype流量控制阀flowcontrolvalve固定节流阀fixedrestrictivevalve 可调节流阀adjustablerestrictivevalve单向节流阀one-wayrestrictivevalve 调速阀speedregulatorvalve分流阀flowdividervalve集流阀flow-combiningvalve 截止阀shut-offvalve球阀global(ball)valve针阀needlevalve闸阀gatevalve膜片阀diaphragmvalve蝶阀butterflyvalve噪声等级noiselevel放大器amplifier模拟放大器analogueamplifier 数字放大器digitalamplifier 传感器sensor阈值threshold伺服阀servo-valve四通阀four-wayvalve喷嘴挡板nozzleflapper液压放大器hydraulicamplifier 颤振dither阀极性valvepolarity流量增益flowgain对称度symmetry流量极限flowlimit 零位内泄漏null(quiescent)leakage 遮盖lap零遮盖zerolap正遮盖overlap负遮盖underlap开口opening零偏nullbias零漂nulldrift阀压降valvepressuredrop分辨率resolution频率响应frequencyresponse幅值比amplituderatio相位移phaselag传递函数transferfunction管路flowline硬管rigidtube软管flexiblehose工作管路workingline回油管路returnline补液管路replenishingline控制管路pilotline泄油管路drainline放气管路bleedline接头fitting；connection焊接式接头weldedfitting扩口式接头flaredfitting快换接头quickreleasecoupling 法兰接头flangeconnection弯头elbow异径接头reducerfitting流道flowpass油口port闭式油箱sealedreservoir油箱容量reservoirfluidcapacity 气囊式蓄能器bladderaccumulator 空气污染aircontamination固体颗粒污染solidcontamination 液体污染liquidcontamination空气过滤器airfilter油雾气lubricator热交换器heatexchanger冷却器cooler加热器heater温度控制器thermostat消声器silencer双筒过滤器duplexfilter 过滤器压降filterpressuredrop有效过滤面积effectivefiltrationarea公称过滤精度nominalfiltrationrating压溃压力collapsepressure填料密封packingseal机械密封mechanicalseal径向密封radialseal旋转密封rotaryseal活塞密封pistonseal活塞杆密封rodseal防尘圈密封wiperseal；scraper组合垫圈bondedwasher复合密封件compositeseal弹性密封件elastomerseal优先控制overridecontrol压力表pressuregauge压力传感器electricalpressuretransducer压差计differentialpressureinstrument 液位计liquidlevelmeasuringinstrument 流量计flowmeter压力开关pressureswitch脉冲发生器pulsegenerator液压泵站powerstation空气处理单元airconditionerunit压力控制回路pressurecontrolcircuit 安全回路safetycircuit差动回路differentialcircuit调速回路flowcontrolcircuit进口节流回路meter-incircuit出口节流回路meter-outcircuit同步回路synchronizingcircuit开式回路opencircuit闭式回路closedcircuit管路布置pipe-work管卡clamper联轴器driveshaftcoupling操作台controlconsole控制屏controlpanel粘度viscosity运动粘度kinematicviscosity密度density 含水量watercontent闪点flashpoint防锈性rustprotection抗腐蚀性anti-corrosivequality便携式颗粒检测仪portableparticlecounter。

常用液压专业英语词汇常用液压专业英语词汇液压是机械行业、机电行业的'一个名词。

液压可以用动力传动方式，成为液压传动。

以下是为大家分享的常用液压专业英语词汇，供大家参考借鉴，欢迎浏览!一、阀类Solenoid valve 电磁阀Check valve 单向阀Cartridge valve 插装阀Sandwich plate valve 叠加阀Pilot valve 先导阀Pilot operated check valve 液控单向阀Sub-plate mount 板式安装Manifold block 集成块Pressure relief valve 压力溢流阀Flow valve 流量阀Throttle valve 节流阀Double throttle check valve 双单向节流阀Rotary knob 旋钮Rectifier plate 节流板Servo valve 伺服阀Proportional valve 比例阀Position feedback 位置反馈Progressive flow 渐增流量De-energizing of solenoid 电磁铁释放二、介质类Phosphate ester (HFD-R) 磷酸甘油酯Water-glycol (HFC) 水-乙二醇Emulsion 乳化液Inhibitor缓蚀剂Synthetic lubricating oil 合成油三、液压安装工程Contamination 污染Grout 灌浆Failure 失效Jog 点动Creep爬行Abrasion 摩擦Retract(活塞杆)伸出Extension (活塞杆)缩回Malfunction 误动作Pickling 酸洗Flushing 冲洗Dipping process 槽式酸洗Re-circulation 循环Passivity 钝化Nitric acid 柠檬酸Argon 氩气Butt welding 对接焊Socket welding 套管焊Inert gas welding 惰性气体焊四、管接头Bite type fittings 卡套式管接头Tube to tube fittings 接管接头union 直通接管接头union elbow 直角管接头union tee 三通管接头union cross 四通管接头Mal stud fittings 端直通管接头Bulkhead fittings 长直通管接头Weld fittings 焊接式管接头Female connector fittings 接头螺母Reducers extenders 变径管接头Banjo fittings 铰接式管接头Adjustable fittings/swivel nut 旋转接头五、伺服阀及伺服系统性能参数Dynamic response 动态频响DDV-direct drive valve 直动式伺服阀NFPA-National Fluid Power Association 美国流体控制学会Phase lag 相位滞后Nozzle flapper valve 喷嘴挡板阀Servo-jet pilot valve 射流管阀Dither 颤振电流Coil impedance 线圈阻抗Flow saturation 流量饱和Linearity 线形度Symmetry 对称性Hysterics 滞环Threshold 灵敏度Lap 滞后Pressure gain 压力增益Null 零位Null bias 零偏Null shift 零飘Frequency response 频率响应。

液压 英语词汇Aability 性能；能力load-carrying ability 承载能力absorber 吸收器；吸收剂；过滤器；减震器 accessories 辅件，附件，配件hydraulic accessories 液压辅件accumulate 储存；蓄能；累积accumulator 蓄能器；蓄电池；累加器 accuracy 准确性；精度action 作用；动作；作用力；行程actuated 操纵，控制directly actuated 直接操纵的，直接控制的 pilot actuated 先导控制的，液控的actuator 执行元件；液压缸；马达adapter 接头；衬套；压环；连接件pipe adapter 管接头admission 供给，供油，供气alignment 找正，定心，对中amplifier 放大器differential pressure amplifier 压差放大器 flow amplifier 流量放大器assembly 组合，组件，机组axis 轴Bback-flow 回流back-up 支撑hydrostatic back-up 静压支撑barrel 桶，缸体base 底座；支座bearing 支承；轴承；方位radial ball bearing 径向球轴承rolling bearing 滚动轴承sliding bearing 滑动轴承thrust bearing 止推轴承bed 台pump test bed 泵试验台behavior 性能；工况bend 弯头；弯管blade 叶片flat blade 平面叶片forward inclined blade 前倾叶片guide blade 导叶radial blade 径向叶片bleed 排气air bleed 排气阀bleeder 排气孔block 块；封闭；块体cartridge valve block 插装阀块体choke block 节流板directional control block 多路阀，方向控制阀组 panel block 阀板组body 体；缸筒；阀体，壳体pump body 泵体tank body 箱体valve body 阀体bolt 螺栓；插销；螺杆boss 轮毂bottom 底；底部cylinder bottom 缸底；缸后盖bracket 支架pump bracket 泵架bubble-tight 气密的buffer 缓冲器，阻尼器bush(ing) 套，导向套；衬套Ccap 帽,盖,罩,塞cylinder end cap 缸端盖cylinder head cap 缸前盖capacity 容量;功率;排量;流量effective capacity 有效排量,实际排量geometric capacity 几何排量,理论排量casing 套,壳,罩gear casing 齿轮箱，变速箱pump casing 泵体cavitation 气蚀cavity 腔centering 中心调整，定心chamber 腔，室；容积；油腔；气腔chamfer 槽；倒角changement 换向机构characteristic 特性曲线；特征线charger 加载装置charging 充液；充压choke 节流；节流口chord 弦circlip 弹性挡圈circuit 回路clearance 间隙clog 阻塞；堵塞cock 龙头collar 圈；法兰盘cushion collar 缓冲套locating collar 定位凸缘套loose collar 轴肩挡圈thrust collar 止推环connection 连接；连接管路；接头 consumption 消耗量cylinder 缸；液压缸Ddebugging 排除故障；调试deflation 排气delivery 流量differential 差动的；微分的 displacement 压出；排出；排量；位移 dowel 定位销drained 泄油的duty 负载，功率；工况Eeffect 作用;效应cavitate effect 气蚀效应choking effect 节流作用elbow 弯头electro-hydraulic 电液的entrap 困油escape 泄漏,逸出,排出etching 蚀刻;腐蚀gas etching 气蚀exhaust 排泄;回油;Ffailure 故障;事故;损坏,失效 fastener 紧固件fatigue 疲劳feedback 反馈filler 加油口,注油口;填料;垫片filter 滤油器flow 流;液流;流程;流束;流量;流动 nominal flow 公称流量rated flow 额定流量stationary flow 定常流,定常流动 streamline flow 层流turbulent flow 紊流volume flow 体积流量flowline 管路;流线flow-regulator 流量调节阀 fluctuation 脉动fluid 流体,液体;射流hydraulic operating fluid 液压油 incompressible fluid 不可压缩流体 frame 座,架Ggain 增益flow gain 流量增益feedback gain 反馈增益gap 间隙,缝隙gear 齿轮,装置,机构governing 调节,控制Hhead 缸头,头部;盖;水头;扬程 cylinder head 缸头static head 静压头theoretic head 理论能头total head 总能头water head 水头hole 孔,洞air hole 气孔blind hole 盲孔bolt hole 螺栓孔bose 胶管,软管housing 壳体;槽hub 毂;衬套hydrostatics 液压技术,液体静力学Iidling 空转impact 冲击,撞击impeller 叶轮closed impeller 闭式叶轮open impeller 开式叶轮pump impeller 泵叶轮incidence 入射;入射角blade incidence 叶片安装角 incompressible 不可压缩的inlet 进口;吸入intensifier 增压器intensity 强度Jjack (柱塞)缸;千斤顶joint 接头;关节cross joint 十字接头flange joint 法兰式接头screwed joint 螺纹接头journal 轴颈jump 跳动;振动pressure jump 压力突变Kkeyway 键槽Llag 滞后;延迟servovalve phase lag 伺服阀相位滞后 laminar 层流的latch 插销;锁紧装置;锁定leak 漏;漏油;渗漏处;漏出物line 管路;线路liner 衬套;导向套;内层胶liquid 液体(的);液力的load 负载;载荷location 位置;定位;安装lock 锁;闭锁;液压卡紧loop 环;环路;回路;循环control loop 控制回路,调节回路 main loop 主回路servo loop 伺服回路loss 损失bend loss 弯头损失blade loss 叶片损失line loss 管路损失local pressure loss 局部压力损失partial loss 局部损失lubricate 润滑lug 耳轴lifting lug 吊环Mmandrel 心轴;芯棒manometer 压力机,压力表meter 米;仪表;计量;节制;控制(流量);流量计meter-in 进口节流meter-out 出口节流motion 动作alternative motion 往复运动lost motion 空转synchronized motion 同步运动motor 发动机,液压马达axial piston motor 轴向柱塞马达bent axis piston motor 斜轴式轴向柱塞马达cam plate type axial piston motor 斜盘式轴向柱塞马达 constant displacement motor 定量马达radial motor 径向马达sliding vane motor 叶片马达swing motor 摆动马达Nnominal 额定的,公称的notch 凹槽relief notch 卸荷槽null 零位Ooff-load 卸荷oil 油oiler 注油器olive 球面卡套grooved olive 迷宫密封环operation 运行;操作;运算orifice 小孔;节流孔O-ring O型密封圈output 输出;排量;流量overload 过载Ppack 包,捆;组合件,部件,单元power pack 液压泵站package包,捆;组件,单元hydraulic package 液压泵站power package 泵站packing 密封;密封装置;填料密封pad 衬垫;底座asbestos pad 石棉垫valve pad 阀垫parameter 参数part 部分;零件;部件partition 隔板passage 流道;通道;通过pedestal 支座,底座motor pedestal 电动机座phenomenon 现象stick-alip phenomenon 爬行现象 trapping phenomenon 困油现象piece 零件,部件pilot(-actuate,-operate) 先导控制;液控 piloted 先导控制的pin 销;插头alignment pin 定位销cottar pin 开口销locking pin 锁紧销piston pin 活塞销straight pin 圆柱销pipe 管子,管道(尤指铸铁管和钢管) piston 活塞;柱塞;阀芯double acting piston 双作用活塞double rod piston 双杆活塞hollow piston 空心活塞single-rod piston 单杆活塞pit 坑;槽pitch 节距pitting 凹痕;锈斑;点蚀plug 堵塞;阻塞;堵头air release plug 排气塞plug-in 插入式的,组合式的poppet 提动阀芯,座阀芯,锥阀芯,碟形阀芯 pore 孔;孔隙port 油口;连接口position 位置;状态;定位center valve position 阀的中间位置 neutral position 中位;零位three position 三位two position 二位pressure 压力,压强;气压pulsation 脉动,波动pump 泵bent axis axial piston pump 斜轴式轴向柱塞泵 booster pump 辅助泵,充液泵cam plate type axial piston pump 斜盘式轴向柱塞泵 centrifugal pump 离心泵constant delivery pump 定量泵cycloid rotor pump 摆线转子泵double action vane pump 双作用叶片泵gear pump 齿轮泵multi-stage pump 多级泵single action vane pump 单作用叶片泵vane pump 叶片泵variable capacity pump 变量泵Rrabbet 球铰rack 齿条;机架racing 空转radian 弧度radius 半径range 范围,量程rated 额定的regulation 调节,调整regulator 调节器,调压阀differential pressure regulator 定差减压阀 proportional pressure regulator 定比减压阀relay 继电器relief 释压;溢流;卸荷reset 复位restriction 节流;阻尼,节流口,阻尼孔restrictor 节流阀;节流口;阻尼孔reversal 反转,倒转revolution 旋转;转数rider 导向套ring 环,圈anti-extrusion ring 密封挡圈,挡圈back support ring 后支承环back-up ring 挡圈bearing ring 导向套dust ring 防尘圈retainer ring 卡环seal ring 密封圈;密封环rod 杆;活塞杆Sscrew 螺杆,螺钉,丝杆,螺旋seal 密封;封口;密封件;密封装置seat 阀座,座seizure 卡死,咬住,擦伤selector 换向阀servo 伺服;伺服机构,伺服系统 servomotor 伺服马达servopump 伺服泵servovalve 伺服阀set 组件;定位;集合shaft 轴pump shaft 泵轴sleeve 套;套管;卡套;阀套slot 缝,隙,槽spring 弹簧stroke 行程symbol 符号functional symbol 职能符号Ttank 箱,缸;油箱;容器tee 三通接头,三通throttle 节流;节流阀trapping 困油travel 位移;行程tube 管子(尤指有色金属和无缝钢管) tubeline 管路Uunion 中间接头;直通接头Vvalve 阀back pressure valve 背压阀bypass valve 旁通阀;溢流阀change valve 换向阀check valve 单向阀direct operated solenoid valve 电磁阀 flow regulating valve 调速阀four port valve 四通阀four position valve 四位阀hand operated valve 手动阀hydraulic operated check valve 液控单向阀 overflow valve 溢流阀overload relief valve 安全阀;过载溢流阀 piloted valve 先导式阀vane 叶片diffusion vane 导叶vent 放气;排气孔volume 容积,体积displacement volume 排量Wwasher 垫圈;衬垫wiper 防尘圈Zzone 地带;区(域)dead zone 死区high pressure zone 高压区low pressure zone 低压区。

液压方面的英语词汇按字母顺序排：Aability 性能；能力load-carrying ability 承载能力absorber 吸收器；吸收剂；过滤器；减震器accessories 辅件，附件，配件hydraulic accessories 液压辅件accumulate 储存；蓄能；累积accumulator 蓄能器；蓄电池；累加器accuracy 准确性；精度action 作用；动作；作用力；行程actuated 操纵，控制directly actuated 直接操纵的，直接控制的pilot actuated 先导控制的，液控的actuator 执行元件；液压缸；马达adapter 接头；衬套；压环；连接件pipe adapter 管接头admission 供给，供油，供气alignment 找正，定心，对中amplifier 放大器differential pressure amplifier 压差放大器flow amplifier 流量放大器assembly 组合，组件，机组axis 轴Bback-flow 回流back-up 支撑hydrostatic back-up 静压支撑barrel 桶，缸体base 底座；支座bearing 支承；轴承；方位radial ball bearing 径向球轴承rolling bearing 滚动轴承sliding bearing 滑动轴承thrust bearing 止推轴承bed 台pump test bed 泵试验台behavior 性能；工况bend 弯头；弯管blade 叶片flat blade 平面叶片forward inclined blade 前倾叶片guide blade 导叶radial blade 径向叶片bleed 排气air bleed 排气阀bleeder 排气孔block 块；封闭；块体cartridge valve block 插装阀块体choke block 节流板directional control block 多路阀，方向控制阀组panel block 阀板组body 体；缸筒；阀体，壳体pump body 泵体tank body 箱体valve body 阀体bolt 螺栓；插销；螺杆boss 轮毂bottom 底；底部cylinder bottom 缸底；缸后盖bracket 支架pump bracket 泵架bubble-tight 气密的buffer 缓冲器，阻尼器bush(ing) 套，导向套；衬套Ccap 帽,盖,罩,塞cylinder end cap 缸端盖cylinder head cap 缸前盖capacity 容量;功率;排量;流量effective capacity 有效排量,实际排量geometric capacity 几何排量,理论排量casing 套,壳,罩gear casing 齿轮箱，变速箱pump casing 泵体cavitation 气蚀cavity 腔centering 中心调整，定心chamber 腔，室；容积；油腔；气腔chamfer 槽；倒角changement 换向机构characteristic 特性曲线；特征线charger 加载装置charging 充液；充压choke 节流；节流口chord 弦circlip 弹性挡圈circuit 回路clearance 间隙clog 阻塞；堵塞cock 龙头collar 圈；法兰盘cushion collar 缓冲套locating collar 定位凸缘套loose collar 轴肩挡圈thrust collar 止推环connection 连接；连接管路；接头consumption 消耗量cylinder 缸；液压缸Ddebugging 排除故障；调试deflation 排气delivery 流量differential 差动的；微分的displacement 压出；排出；排量；位移dowel 定位销drained 泄油的duty 负载，功率；工况Eeffect 作用;效应cavitate effect 气蚀效应choking effect 节流作用elbow 弯头electro-hydraulic 电液的entrap 困油escape 泄漏,逸出,排出etching 蚀刻;腐蚀gas etching 气蚀exhaust 排泄;回油;Ffailure 故障;事故;损坏,失效fastener 紧固件fatigue 疲劳feedback 反馈filler 加油口,注油口;填料;垫片filter 滤油器flow 流;液流;流程;流束;流量;流动nominal flow 公称流量rated flow 额定流量stationary flow 定常流,定常流动streamline flow 层流turbulent flow 紊流volume flow 体积流量flowline 管路;流线flow-regulator 流量调节阀fluctuation 脉动fluid 流体,液体;射流hydraulic operating fluid 液压油incompressible fluid 不可压缩流体frame 座,架Ggain 增益flow gain 流量增益feedback gain 反馈增益gap 间隙,缝隙gear 齿轮,装置,机构governing 调节,控制Hhead 缸头,头部;盖;水头;扬程cylinder head 缸头static head 静压头theoretic head 理论能头total head 总能头water head 水头hole 孔,洞air hole 气孔blind hole 盲孔bolt hole 螺栓孔bose 胶管,软管housing 壳体;槽hub 毂;衬套hydrostatics 液压技术,液体静力学Iidling 空转impact 冲击,撞击impeller 叶轮closed impeller 闭式叶轮open impeller 开式叶轮pump impeller 泵叶轮incidence 入射;入射角blade incidence 叶片安装角incompressible 不可压缩的inlet 进口;吸入intensifier 增压器intensity 强度Jjack (柱塞)缸;千斤顶joint 接头;关节cross joint 十字接头flange joint 法兰式接头screwed joint 螺纹接头journal 轴颈jump 跳动;振动pressure jump 压力突变Kkeyway 键槽Llag 滞后;延迟servovalve phase lag 伺服阀相位滞后laminar 层流的latch 插销;锁紧装置;锁定leak 漏;漏油;渗漏处;漏出物line 管路;线路liner 衬套;导向套;内层胶liquid 液体(的);液力的load 负载;载荷location 位置;定位;安装lock 锁;闭锁;液压卡紧loop 环;环路;回路;循环control loop 控制回路,调节回路main loop 主回路servo loop 伺服回路loss 损失bend loss 弯头损失blade loss 叶片损失line loss 管路损失local pressure loss 局部压力损失partial loss 局部损失lubricate 润滑lug 耳轴lifting lug 吊环M mandrel 心轴;芯棒manometer 压力机,压力表meter 米;仪表;计量;节制;控制(流量);流量计meter-in 进口节流meter-out 出口节流motion 动作alternative motion 往复运动lost motion 空转synchronized motion 同步运动motor 发动机,液压马达axial piston motor 轴向柱塞马达bent axis piston motor 斜轴式轴向柱塞马达cam plate type axial piston motor 斜盘式轴向柱塞马达constant displacement motor 定量马达radial motor 径向马达sliding vane motor 叶片马达swing motor 摆动马达Nnominal 额定的,公称的notch 凹槽relief notch 卸荷槽null 零位Ooff-load 卸荷oil 油oiler 注油器olive 球面卡套grooved olive 迷宫密封环operation 运行;操作;运算orifice 小孔;节流孔O-ring O型密封圈output 输出;排量;流量overload 过载Ppack 包,捆;组合件,部件,单元power pack 液压泵站package包,捆;组件,单元hydraulic package 液压泵站power package 泵站packing 密封;密封装置;填料密封pad 衬垫;底座asbestos pad 石棉垫valve pad 阀垫parameter 参数part 部分;零件;部件partition 隔板passage 流道;通道;通过pedestal 支座,底座motor pedestal 电动机座phenomenon 现象stick-alip phenomenon 爬行现象trapping phenomenon 困油现象piece 零件,部件pilot(-actuate,-operate) 先导控制;液控piloted 先导控制的pin 销;插头alignment pin 定位销cottar pin 开口销locking pin 锁紧销piston pin 活塞销straight pin 圆柱销pipe 管子,管道(尤指铸铁管和钢管)piston 活塞;柱塞;阀芯double acting piston 双作用活塞double rod piston 双杆活塞hollow piston 空心活塞single-rod piston 单杆活塞pit 坑;槽pitch 节距pitting 凹痕;锈斑;点蚀plug 堵塞;阻塞;堵头air release plug 排气塞plug-in 插入式的,组合式的poppet 提动阀芯,座阀芯,锥阀芯,碟形阀芯pore 孔;孔隙port 油口;连接口position 位置;状态;定位center valve position 阀的中间位置neutral position 中位;零位three position 三位two position 二位pressure 压力,压强;气压pulsation 脉动,波动pump 泵bent axis axial piston pump 斜轴式轴向柱塞泵booster pump 辅助泵,充液泵cam plate type axial piston pump 斜盘式轴向柱塞泵centrifugal pump 离心泵constant delivery pump 定量泵cycloid rotor pump 摆线转子泵double action vane pump 双作用叶片泵gear pump 齿轮泵multi-stage pump 多级泵single action vane pump 单作用叶片泵vane pump 叶片泵variable capacity pump 变量泵Rrabbet 球铰rack 齿条;机架racing 空转radian 弧度radius 半径range 范围,量程rated 额定的regulation 调节,调整regulator 调节器,调压阀differential pressure regulator 定差减压阀proportional pressure regulator 定比减压阀relay 继电器relief 释压;溢流;卸荷reset 复位restriction 节流;阻尼,节流口,阻尼孔restrictor 节流阀;节流口;阻尼孔reversal 反转,倒转revolution 旋转;转数rider 导向套ring 环,圈anti-extrusion ring 密封挡圈,挡圈back support ring 后支承环back-up ring 挡圈bearing ring 导向套dust ring 防尘圈retainer ring 卡环seal ring 密封圈;密封环rod 杆;活塞杆Sscrew 螺杆,螺钉,丝杆,螺旋seal 密封;封口;密封件;密封装置seat 阀座,座seizure 卡死,咬住,擦伤selector 换向阀servo 伺服;伺服机构,伺服系统servomotor 伺服马达servopump 伺服泵servovalve 伺服阀set 组件;定位;集合shaft 轴pump shaft 泵轴sleeve 套;套管;卡套;阀套slot 缝,隙,槽spring 弹簧stroke 行程symbol 符号functional symbol 职能符号Ttank 箱,缸;油箱;容器tee 三通接头,三通throttle 节流;节流阀trapping 困油travel 位移;行程tube 管子(尤指有色金属和无缝钢管) tubeline 管路Uunion 中间接头;直通接头Vvalve 阀back pressure valve 背压阀bypass valve 旁通阀;溢流阀change valve 换向阀check valve 单向阀direct operated solenoid valve 电磁阀flow regulating valve 调速阀four port valve 四通阀four position valve 四位阀hand operated valve 手动阀hydraulic operated check valve 液控单向阀overflow valve 溢流阀overload relief valve 安全阀;过载溢流阀piloted valve 先导式阀vane 叶片diffusion vane 导叶vent 放气;排气孔volume 容积,体积displacement volume 排量Wwasher 垫圈;衬垫wiper 防尘圈Zzone 地带;区(域)dead zone 死区high pressure zone 高压区low pressure zone 低压区按分类排：1、阀类Flow valve 流量阀Throttle valve 节流阀Double throttle check valve 双单向节流阀flow divider valve 分流阀shut-off valve 截止阀global(ball) valve 球阀needle valve 针阀gate valve 闸阀diaphragm valv膜片阀diaphragm 隔膜，振动膜，光圈butterfly valve 蝶阀valve 阀sub-plate 底板manifold block 油路块sub-plate valve板式阀sandwich valve叠加阀cartridge valve 插装阀slide valve滑阀poppet valve 锥阀valve element 阀芯valve element position 阀芯位置check valve 单向阀pilot-controlled check valve液控单向阀shuttle valve 梭阀pressure relief valve压力控制阀pressure relief valve 溢流阀Pressure relief valve 压力溢流阀sequence valve 顺序阀pressure reducing valve减压阀counterbalance valve平衡阀unloading valve卸荷阀flow control valve流量控制阀directional valve方向控制阀accessory液压辅件common valve普通阀Solenoid valve 电磁阀Check valve 单向阀Cartridge valve 插装阀Sandwich plate valve 叠加阀Pilot valve 先导阀Pilot operated check valve 液控单向阀Sub-plate mount 板式安装Manifold block 集成块Rotary knob 旋钮Rectifier plate 节流板Servo valve 伺服阀Proportional valve 比例阀Position feedback 位置反馈Progressive flow 渐增流量De-energizing of solenoid 电磁铁释放fixed restrictive valve固定节流阀adjustable restrictive valve可调节流阀one-way restrictive valve单向节流阀speed regulator valve 调速阀flow divider valve分流阀flow-combining valve集流阀DDV-direct drive valve 直动式伺服阀2、介质类Phosphate ester (HFD-R) 磷酸甘油酯Water-glycol (HFC) 水-乙二醇Emulsion 乳化液Inhibitor缓蚀剂Synthetic lubricating oil 合成油3、液压安装工程Contamination 污染Grout 灌浆Failure 失效Jog点动Creep爬行Abrasion 摩擦Retract（活塞杆）伸出Extension （活塞杆）缩回Malfunction 误动作Pickling 酸洗Flushing 冲洗Dipping process 槽式酸洗Re-circulation 循环Passivity 钝化Nitric acid 柠檬酸Argon 氩气Butt welding 对接焊Socket welding 套管焊Inert gas welding 惰性气体焊4、管接头Bite type fittings 卡套式管接头Tube to tube fittings 接管接头union 直通接管接头union elbow 直角管接头union tee 三通管接头union cross 四通管接头Mal stud fittings 端直通管接头Bulkhead fittings 长直通管接头Weld fittings 焊接式管接头Female connector fittings 接头螺母Reducers extenders 变径管接头Banjo fittings 铰接式管接头Adjustable fittings/swivel nut 旋转接头5、伺服阀及伺服系统性能参数Dynamic response 动态频响DDV-direct drive valve 直动式伺服阀NFPA-National Fluid Power Association 美国流体控制学会Phase lag 相位滞后Nozzle flapper valve 喷嘴挡板阀Servo-jet pilot valve 射流管阀Dither 颤振电流Coil impedance 线圈阻抗Flow saturation 流量饱和Linearity 线形度Symmetry 对称性Hysterics 滞环Threshold 灵敏度Lap 滞后Pressure gain 压力增益Null 零位Null bias 零偏Null shift 零飘Frequency response 频率响应Slope 曲线斜坡液压专业英语词汇acceptable conditions许用工况actual conditions实际工况actual force实际输出力air contamination空气污染air consumption耗气量air conditioner unit空气处理单元air filter空气过滤器adjustable restrictive valve可调节流阀amplifier放大器amplitude ratio幅值比analogue amplifier模拟放大器anti-corrosive quality抗腐蚀性automatic cycle自动循环axial piston pump轴向柱塞泵back pressure背压bladder accumulator气囊式蓄能器bleed line放气管路bonded washer组合垫圈breakout pressure启动压力butterfly valve蝶阀cartridge valve插装阀cavitation气穴charge pressure充油压力check valve单向阀circle循环circuit diagram回路图clamper管卡closed circuit闭式回路collapse pressure压溃压力compensator避震喉composite seal复合密封件continuous working conditions连续工况control of pump泵的控制control console操作台control panel控制屏cooler冷却器counterbalance valve平衡阀cracking pressure开启压力cushioning缓冲cylinder缸cycling speed循环速度De-energizing of solenoid 电磁铁释放density密度diaphragm valve膜片阀differential circuit差动回路differential cylinder差动缸differential pressure instrument压差计digital amplifier数字放大器direction of rotation旋转方向directly operated type直动式displacement排量dither颤振double-acting cylinder双作用缸Double throttle check valve 双单向节流阀drain line泄油管路drift漂移drive shaft coupling联轴器dwell phase停止工步duplex filter双筒过滤器efficiency效率effective filtration area有效过滤面积elastomer seal弹性密封件elbow弯头electrical pressure transducer压力传感器external leakage外泄漏extend stroke外伸行程filter pressure drop过滤器压降fitting；connection接头fixed restrictive valve固定节流阀flared fitting扩口式接头flash point闪点flexible hose软管flange connection法兰接头flange mounting法兰安装flow-combining valve集流阀flow control valve流量控制阀flow control circuit调速回路flow divider valve分流阀flow gain流量增益flow limit流量极限flow line管路flow meter流量计flow pass流道flow rate流量Flow valve 流量阀flower factor流量系数foot mounting底座安装force输出力four-way valve四通阀free position自由位frequency response频率响应function diagram功能图gate valve闸阀gear pump齿轮泵global(ball) valve球阀graphical symbol图形符号heat exchanger热交换器heater加热器hydraulic lock液压锁紧hydraulic motor液压马达hydraulic power流体传动hydraulics液压技术hydrodynamics液力技术hydropneumatics气液技术hysteresis滞环hydraulic amplifier液压放大器hydraulic controlled type液控式instantaneous conditions瞬态工况internal leakage内泄漏inlet pressure进口压力induced pressure负载压力kinematic viscosity运动粘度laminar flow层流lap遮盖leakage泄漏limited conditions极限工况linearity线性度linear region线性区liquid contamination液体污染liquid level measuring instrument液位计lubricator油雾气manually operated type手动式manifold block油路块mechanically controlled type机械控制式 mechanical seal机械密封meter-in circuit进口节流回路meter-out circuit出口节流回路Manifold block 集成块needle valve针阀neutral position中位nitrile butadiene rubber；NBR丁腈橡胶noise level噪声等级nominal filtration rating公称过滤精度nominal pressure公称压力nozzle flapper喷嘴挡板null bias零偏null drift零漂null(quiescent) leakage零位内泄漏one-way restrictive valve单向节流阀opening开口open circuit开式回路operating conditions运行工况operating pressure运行压力outlet pressure出口压力over lap正遮盖override pressure调压偏差override control优先控制packing seal填料密封peak pressure峰值压力phase工步phase lag相位移Pilot valve 先导阀pilot pressure控制压力pilot-controlled check valve液控单向阀pilot-operated type先导式Pilot operated check valve 液控单向阀piston pump柱塞泵pilot line控制管路pipe-work管路布置piston seal活塞密封polytetrafluoroethene；PTFE聚四氟乙烯poppet valve锥阀portable particle counter便携式颗粒检测仪port油口Position feedback 位置反馈power station液压泵站pre-charge pressure充气压力pressure control circuit压力控制回路pressure drop；differential pressure压降pressure gauge压力表Pressure relief valve 压力溢流阀pressure switch压力开关pressure time diagram压力－时间图pressure relief valve压力控制阀pressure relief valve溢流阀pressure reducing valve减压阀Progressive flow 渐增流量Proportional valve 比例阀proof pressure耐压试验压力pulse generator脉冲发生器quick release coupling快换接头radial seal径向密封rapid advance phase快进工步rapid return phase快退工步rated conditions额定工况rated flow额定流量rated pressure额定压力rear end无杆端Rectifier plate 节流板reducer fitting异径接头replenishing line补液管路reservoir fluid capacity油箱容量resolution分辨率retract stroke内缩行程return line回油管路repeat ability重复性reproducibility复现性rigid tube硬管ripple波动rod end有杆端rod seal活塞杆密封rotary seal旋转密封Rotary knob 旋钮rust protection防锈性safety circuit安全回路sandwich valve叠加阀Sandwich plate valve 叠加阀sealed reservoir闭式油箱sensor传感器sequence valve顺序阀servo-valve伺服阀shut-off valve截止阀shuttle valve梭阀silencer消声器single-acting cylinder单作用缸slide valve滑阀solid contamination固体颗粒污染Solenoid valve 电磁阀speed regulator valve调速阀流体传动hydraulic power液压技术hydraulics液力技术hydrodynamics气液技术hydropneumatics运行工况operating conditions额定工况rated conditions极限工况limited conditions瞬态工况instantaneous conditions稳态工况steady-state conditions许用工况acceptable conditions连续工况continuous working conditions 实际工况actual conditions效率efficiency旋转方向direction of rotation公称压力nominal pressure工作压力working pressure进口压力inlet pressure出口压力outlet pressure压降pressure drop；differential pressure背压back pressure启动压力breakout pressure充油压力charge pressure开启压力cracking pressure峰值压力peak pressure运行压力operating pressure耐压试验压力proof pressure冲击压力surge pressure静压力static pressure系统压力system pressure控制压力pilot pressure充气压力pre-charge pressure吸入压力suction pressure调压偏差override pressure额定压力rated pressure耗气量air consumption泄漏leakage内泄漏internal leakage外泄漏external leakage层流laminar flow紊流turbulent flow气穴cavitation流量flow rate排量displacement额定流量rated flow供给流量supply flow流量系数flower factor滞环hysteresis图形符号graphical symbol液压气动元件图形符号symbols for hydraulic and pneumatic components流体逻辑元件图形符号symbols for fluid logic devices逻辑功能图形符号symbols for logic functions回路图circuit diagram压力－时间图pressure time diagram功能图function diagram循环circle自动循环automatic cycle工作循环working cycle循环速度cycling speed工步phase停止工步dwell phase工作工步working phase快进工步rapid advance phase快退工步rapid return phase频率响应frequency response重复性repeat ability复现性reproducibility漂移drift波动ripple线性度linearity线性区linear region液压锁紧hydraulic lock液压卡紧sticking变量泵variable displacement pump 泵的控制control of pump齿轮泵gear pump叶片泵vane pump柱塞泵piston pump轴向柱塞泵axial piston pump法兰安装flange mounting底座安装foot mounting液压马达hydraulic motor刚度stiffness中位neutral position零位zero position自由位free position缸cylinder有杆端rod end无杆端rear end外伸行程extend stroke内缩行程retract stroke缓冲cushioning工作行程working stroke负载压力induced pressure输出力force实际输出力actual force单作用缸single-acting cylinder双作用缸double-acting cylinder差动缸differential cylinder伸缩缸telescopic cylinder阀valve底板sub-plate 油路块manifold block板式阀sub-plate valve叠加阀sandwich valve插装阀cartridge valve滑阀slide valve锥阀poppet valve阀芯valve element阀芯位置valve element position单向阀check valve液控单向阀pilot-controlled check valve 梭阀shuttle valve压力控制阀pressure relief valve溢流阀pressure relief valve顺序阀sequence valve减压阀pressure reducing平衡阀counterbalance valve卸荷阀unloading valve直动式directly operated type先导式pilot-operated type机械控制式mechanically controlled type 手动式manually operated type液控式hydraulic controlled type流量控制阀flow control valve固定节流阀fixed restrictive valve可调节流阀adjustable restrictive valve 单向节流阀one-way restrictive valve调速阀speed regulator valve分流阀flow divider valve集流阀flow-combining valve截止阀shut-off valve球阀global(ball) valve针阀needle valve闸阀gate valve膜片阀diaphragm valve蝶阀butterfly valve噪声等级noise level放大器amplifier模拟放大器analogue amplifier数字放大器digital amplifier传感器sensor阈值threshold伺服阀servo-valve四通阀four-way valve喷嘴挡板nozzle flapper液压放大器hydraulic amplifier颤振dither阀极性valve polarity流量增益flow gain对称度symmetry流量极限flow limit零位内泄漏null(quiescent) leakage 遮盖lap零遮盖zero lap正遮盖over lap负遮盖under lap开口opening零偏null bias零漂null drift阀压降valve pressure drop分辨率resolution频率响应frequency response幅值比amplitude ratio相位移phase lag传递函数transfer function管路flow line硬管rigid tube软管flexible hose工作管路working line回油管路return line补液管路replenishing line控制管路pilot line泄油管路drain line放气管路bleed line接头fitting；connection焊接式接头welded fitting扩口式接头flared fitting快换接头quick release coupling法兰接头flange connection弯头elbow异径接头reducer fitting流道flow pass油口port闭式油箱sealed reservoir油箱容量reservoir fluid capacity 气囊式蓄能器bladder accumulator 空气污染air contamination固体颗粒污染solid contamination 液体污染liquid contamination空气过滤器air filter油雾气lubricator热交换器heat exchanger冷却器cooler 加热器heater温度控制器thermostat消声器silencer双筒过滤器duplex filter过滤器压降filter pressure drop有效过滤面积effective filtration area公称过滤精度nominal filtration rating压溃压力collapse pressure填料密封packing seal机械密封mechanical seal径向密封radial seal旋转密封rotary seal活塞密封piston seal活塞杆密封rod seal防尘圈密封wiper seal；scraper组合垫圈bonded washer复合密封件composite seal弹性密封件elastomer seal丁腈橡胶nitrile butadiene rubber；NBR 聚四氟乙烯polytetrafluoroethene；PTFE 优先控制override control压力表pressure gauge压力传感器electrical pressure transducer 压差计differential pressure instrument液位计liquid level measuring instrument 流量计flow meter压力开关pressure switch脉冲发生器pulse generator液压泵站power station空气处理单元air conditioner unit压力控制回路pressure control circuit安全回路safety circuit差动回路differential circuit调速回路flow control circuit进口节流回路meter-in circuit。

液压方面的英语单词目录按字母排序 (1)按分类排序 (10)其他总结的词汇 (13)按字母排序Aability 性能；能力load-carrying ability 承载能力absorber 吸收器；吸收剂；过滤器；减震器accessories 辅件，附件，配件hydraulic accessories 液压辅件accumulate 储存；蓄能；累积accumulator 蓄能器；蓄电池；累加器accuracy 准确性；精度action 作用；动作；作用力；行程actuated 操纵，控制directly actuated 直接操纵的，直接控制的pilot actuated 先导控制的，液控的actuator 执行元件；液压缸；马达adapter 接头；衬套；压环；连接件pipe adapter 管接头admission 供给，供油，供气alignment 找正，定心，对中amplifier 放大器differential pressure amplifier 压差放大器flow amplifier 流量放大器assembly 组合，组件，机组axis 轴Bback-flow 回流back-up 支撑hydrostatic back-up 静压支撑barrel 桶，缸体base 底座；支座bearing 支承；轴承；方位radial ball bearing 径向球轴承rolling bearing 滚动轴承sliding bearing 滑动轴承thrust bearing 止推轴承bed 台pump test bed 泵试验台behavior 性能；工况bend 弯头；弯管blade 叶片flat blade 平面叶片forward inclined blade 前倾叶片guide blade 导叶radial blade 径向叶片bleed 排气air bleed 排气阀bleeder 排气孔block 块；封闭；块体cartridge valve block 插装阀块体choke block 节流板directional control block 多路阀，方向控制阀组panel block 阀板组body 体；缸筒；阀体，壳体pump body 泵体tank body 箱体valve body 阀体bolt 螺栓；插销；螺杆boss 轮毂bottom 底；底部cylinder bottom 缸底；缸后盖bracket 支架pump bracket 泵架bubble-tight 气密的buffer 缓冲器，阻尼器bush(ing) 套，导向套；衬套Ccap 帽,盖,罩,塞cylinder end cap 缸端盖cylinder head cap 缸前盖capacity 容量;功率;排量;流量effective capacity 有效排量,实际排量geometric capacity 几何排量,理论排量casing 套,壳,罩gear casing 齿轮箱，变速箱pump casing 泵体cavitation 气蚀cavity 腔centering 中心调整，定心chamber 腔，室；容积；油腔；气腔chamfer 槽；倒角changement 换向机构characteristic 特性曲线；特征线charger 加载装置charging 充液；充压choke 节流；节流口chord 弦circlip 弹性挡圈circuit 回路clearance 间隙clog 阻塞；堵塞cock 龙头collar 圈；法兰盘cushion collar 缓冲套locating collar 定位凸缘套loose collar 轴肩挡圈thrust collar 止推环connection 连接；连接管路；接头consumption 消耗量cylinder 缸；液压缸Ddebugging 排除故障；调试deflation 排气delivery 流量differential 差动的；微分的displacement 压出；排出；排量；位移dowel 定位销drained 泄油的duty 负载，功率；工况Eeffect 作用;效应cavitate effect 气蚀效应choking effect 节流作用elbow 弯头electro-hydraulic 电液的entrap 困油escape 泄漏,逸出,排出etching 蚀刻;腐蚀gas etching 气蚀exhaust 排泄;回油;Ffailure 故障;事故;损坏,失效fastener 紧固件fatigue 疲劳feedback 反馈filler 加油口,注油口;填料;垫片filter 滤油器flow 流;液流;流程;流束;流量;流动nominal flow 公称流量rated flow 额定流量stationary flow 定常流,定常流动streamline flow 层流turbulent flow 紊流volume flow 体积流量flowline 管路;流线flow-regulator 流量调节阀fluctuation 脉动fluid 流体,液体;射流hydraulic operating fluid 液压油incompressible fluid 不可压缩流体frame 座,架Ggain 增益flow gain 流量增益feedback gain 反馈增益gap 间隙,缝隙gear 齿轮,装置,机构governing 调节,控制Hhead 缸头,头部;盖;水头;扬程cylinder head 缸头static head 静压头theoretic head 理论能头total head 总能头water head 水头hole 孔,洞air hole 气孔blind hole 盲孔bolt hole 螺栓孔bose 胶管,软管housing 壳体;槽hub 毂;衬套hydrostatics 液压技术,液体静力学Iidling 空转impact 冲击,撞击impeller 叶轮closed impeller 闭式叶轮open impeller 开式叶轮pump impeller 泵叶轮incidence 入射;入射角blade incidence 叶片安装角incompressible 不可压缩的inlet 进口;吸入intensifier 增压器intensity 强度Jjack (柱塞)缸;千斤顶joint 接头;关节cross joint 十字接头flange joint 法兰式接头screwed joint 螺纹接头journal 轴颈jump 跳动;振动pressure jump 压力突变Kkeyway 键槽Llag 滞后;延迟servovalve phase lag 伺服阀相位滞后laminar 层流的latch 插销;锁紧装置;锁定leak 漏;漏油;渗漏处;漏出物line 管路;线路liner 衬套;导向套;内层胶liquid 液体(的);液力的load 负载;载荷location 位置;定位;安装lock 锁;闭锁;液压卡紧loop 环;环路;回路;循环control loop 控制回路,调节回路main loop 主回路servo loop 伺服回路loss 损失bend loss 弯头损失blade loss 叶片损失line loss 管路损失local pressure loss 局部压力损失partial loss 局部损失lubricate 润滑lug 耳轴lifting lug 吊环Mmandrel 心轴;芯棒manometer 压力机,压力表meter 米;仪表;计量;节制;控制(流量);流量计meter-in 进口节流meter-out 出口节流motion 动作alternative motion 往复运动lost motion 空转synchronized motion 同步运动motor 发动机,液压马达axial piston motor 轴向柱塞马达bent axis piston motor 斜轴式轴向柱塞马达cam plate type axial piston motor 斜盘式轴向柱塞马达constant displacement motor 定量马达radial motor 径向马达sliding vane motor 叶片马达swing motor 摆动马达Nnominal 额定的,公称的notch 凹槽relief notch 卸荷槽null 零位Ooff-load 卸荷oil 油oiler 注油器olive 球面卡套grooved olive 迷宫密封环operation 运行;操作;运算orifice 小孔;节流孔O-ring O型密封圈output 输出;排量;流量overload 过载Ppack 包,捆;组合件,部件,单元power pack 液压泵站package包,捆;组件,单元hydraulic package 液压泵站power package 泵站packing 密封;密封装置;填料密封pad 衬垫;底座asbestos pad 石棉垫valve pad 阀垫parameter 参数part 部分;零件;部件partition 隔板passage 流道;通道;通过pedestal 支座,底座motor pedestal 电动机座phenomenon 现象stick-alip phenomenon 爬行现象trapping phenomenon 困油现象piece 零件,部件pilot(-actuate,-operate) 先导控制;液控piloted 先导控制的pin 销;插头alignment pin 定位销cottar pin 开口销locking pin 锁紧销piston pin 活塞销straight pin 圆柱销pipe 管子,管道(尤指铸铁管和钢管) piston 活塞;柱塞;阀芯double acting piston 双作用活塞double rod piston 双杆活塞hollow piston 空心活塞single-rod piston 单杆活塞pit 坑;槽pitch 节距pitting 凹痕;锈斑;点蚀plug 堵塞;阻塞;堵头air release plug 排气塞plug-in 插入式的,组合式的poppet 提动阀芯,座阀芯,锥阀芯,碟形阀芯pore 孔;孔隙port 油口;连接口position 位置;状态;定位center valve position 阀的中间位置neutral position 中位;零位three position 三位two position 二位pressure 压力,压强;气压pulsation 脉动,波动pump 泵bent axis axial piston pump 斜轴式轴向柱塞泵booster pump 辅助泵,充液泵cam plate type axial piston pump 斜盘式轴向柱塞泵centrifugal pump 离心泵constant delivery pump 定量泵cycloid rotor pump 摆线转子泵double action vane pump 双作用叶片泵gear pump 齿轮泵multi-stage pump 多级泵single action vane pump 单作用叶片泵vane pump 叶片泵variable capacity pump 变量泵Rrabbet 球铰rack 齿条;机架racing 空转radian 弧度radius 半径range 范围,量程rated 额定的regulation 调节,调整regulator 调节器,调压阀differential pressure regulator 定差减压阀proportional pressure regulator 定比减压阀relay 继电器relief 释压;溢流;卸荷reset 复位restriction 节流;阻尼,节流口,阻尼孔restrictor 节流阀;节流口;阻尼孔reversal 反转,倒转revolution 旋转;转数rider 导向套ring 环,圈anti-extrusion ring 密封挡圈,挡圈back support ring 后支承环back-up ring 挡圈bearing ring 导向套dust ring 防尘圈retainer ring 卡环seal ring 密封圈;密封环rod 杆;活塞杆Sscrew 螺杆,螺钉,丝杆,螺旋seal 密封;封口;密封件;密封装置seat 阀座,座seizure 卡死,咬住,擦伤selector 换向阀servo 伺服;伺服机构,伺服系统servomotor 伺服马达servopump 伺服泵servovalve 伺服阀set 组件;定位;集合shaft 轴pump shaft 泵轴sleeve 套;套管;卡套;阀套slot 缝,隙,槽spring 弹簧stroke 行程symbol 符号functional symbol 职能符号Ttank 箱,缸;油箱;容器tee 三通接头,三通throttle 节流;节流阀trapping 困油travel 位移;行程tube 管子(尤指有色金属和无缝钢管) tubeline 管路Uunion 中间接头;直通接头Vvalve 阀back pressure valve 背压阀bypass valve 旁通阀;溢流阀change valve 换向阀check valve 单向阀direct operated solenoid valve 电磁阀flow regulating valve 调速阀four port valve 四通阀four position valve 四位阀hand operated valve 手动阀hydraulic operated check valve 液控单向阀overflow valve 溢流阀overload relief valve 安全阀;过载溢流阀piloted valve 先导式阀vane 叶片diffusion vane 导叶vent 放气;排气孔volume 容积,体积displacement volume 排量Wwasher 垫圈;衬垫wiper 防尘圈Zzone 地带;区(域)dead zone 死区high pressure zone 高压区low pressure zone 低压区按分类排序一、阀类出口节流回路meter-out circuit同步回路synchronizing circuit开式回路open circuit闭式回路closed circuit管路布置pipe-work管卡clamper联轴器drive shaft coupling操作台control console控制屏control panel避震喉compensator粘度viscosity运动粘度kinematic viscosity密度density含水量water content闪点flash point防锈性rust protection抗腐蚀性anti-corrosive quality便携式颗粒检测仪portable particle counter 电磁阀Solenoid valve单向阀Check valve插装阀Cartridge valve叠加阀Sandwich plate valve先导阀Pilot valve液控单向阀Pilot operated check valve板式安装Sub-plate mount集成块Manifold block压力溢流阀Pressure relief valve流量阀Flow valve节流阀Throttle valve双单向节流阀Double throttle check valve 旋钮Rotary knob节流板Rectifier plate伺服阀Servo valve比例阀Proportional valve位置反馈Position feedback渐增流量Progressive flow电磁铁释放De-energizing of solenoid二、介质类磷酸甘油酯Phosphate ester (HFD-R)水-乙二醇Water-glycol (HFC)乳化液Emulsion缓蚀剂Inhibitor合成油Synthetic lubricating oil三、液压安装工程污染Contamination灌浆Grout失效Failure点动Jog爬行Creep摩擦Abrasion（活塞杆）伸出Retract（活塞杆）缩回Extension误动作Malfunction酸洗Pickling冲洗Flushing槽式酸洗Dipping process循环Re-circulation钝化Passivity柠檬酸Nitric acid氩气Argon对接焊Butt welding套管焊Socket welding惰性气体焊Inert gas welding四、管接头Bite type fittings 卡套式管接头Tube to tube fittings接管接头union 直通接管接头union elbow 直角管接头union tee 三通管接头union cross 四通管接头Mal stud fittings 端直通管接头Bulkhead fittings 长直通管接头Weld fittings 焊接式管接头Female connector fittings 接头螺母Reducers extenders 变径管接头Banjo fittings 铰接式管接头Adjustable fittings/swivel nut 旋转接头五、伺服阀及伺服系统性能参数Dynamic response 动态频响DDV-direct drive valve 直动式伺服阀NFPA-National Fluid Power Association 美国流体控制学会Phase lag 相位滞后Nozzle flapper valve 喷嘴挡板阀Servo-jet pilot valve 射流管阀Dither 颤振电流Coil impedance 线圈阻抗Flow saturation 流量饱和Linearity 线形度Symmetry 对称性Hysterics 滞环Threshold 灵敏度Lap 滞后Pressure gain 压力增益Null 零位Null bias 零偏Null shift 零飘Frequency response 频率响应Slope 曲线斜坡液压系统（hydraulic system）执行元件（actuator）液压缸（cylinder）液压马达（motor）液压回路（circuit）压力控制回路（pressure control）流量（速度）控制回路（speed control）方向控制回路（directional valve control）安全回路（security control）定位回路（position control）同步回路（synchronise circuit）顺序动作回路（sequeunt circuit）液压泵（pump）阀（valve）压力控制阀（pressure valve）流量控制阀（flow valve）方向控制阀（directional valve）液压辅件（accessory）普通阀（common valve）其他总结的词汇流体传动hydraulic power液压技术hydraulics液力技术hydrodynamics气液技术hydropneumatics运行工况operating conditions额定工况rated conditions极限工况limited conditions瞬态工况instantaneous conditions稳态工况steady-state conditions许用工况acceptable conditions连续工况continuous working conditions 实际工况actual conditions效率efficiency旋转方向direction of rotation公称压力nominal pressure工作压力working pressure进口压力inlet pressure出口压力outlet pressure压降pressure drop；differential pressure背压back pressure启动压力breakout pressure充油压力charge pressure开启压力cracking pressure峰值压力peak pressure运行压力operating pressure耐压试验压力proof pressure冲击压力surge pressure静压力static pressure系统压力system pressure控制压力pilot pressure充气压力pre-charge pressure吸入压力suction pressure调压偏差override pressure额定压力rated pressure耗气量air consumption泄漏leakage内泄漏internal leakage外泄漏external leakage层流laminar flow紊流turbulent flow气穴cavitation流量flow rate排量displacement额定流量rated flow供给流量supply flow流量系数flower factor滞环hysteresis图形符号graphical symbol液压气动元件图形符号symbols for hydraulic and pneumatic components 流体逻辑元件图形符号symbols for fluid logic devices逻辑功能图形符号symbols for logic functions回路图circuit diagram压力－时间图pressure time diagram功能图function diagram循环circle自动循环automatic cycle工作循环working cycle循环速度cycling speed工步phase停止工步dwell phase工作工步working phase快进工步rapid advance phase快退工步rapid return phase频率响应frequency response重复性repeat ability复现性reproducibility漂移drift波动ripple线性度linearity线性区linear region液压锁紧hydraulic lock液压卡紧sticking变量泵variable displacement pump 泵的控制control of pump齿轮泵gear pump叶片泵vane pump柱塞泵piston pump轴向柱塞泵axial piston pump法兰安装flange mounting底座安装foot mounting液压马达hydraulic motor刚度stiffness中位neutral position零位zero position自由位free position缸cylinder有杆端rod end无杆端rear end外伸行程extend stroke内缩行程retract stroke缓冲cushioning工作行程working stroke负载压力induced pressure输出力force实际输出力actual force单作用缸single-acting cylinder双作用缸double-acting cylinder差动缸differential cylinder伸缩缸telescopic cylinder阀valve底板sub-plate油路块manifold block板式阀sub-plate valve叠加阀sandwich valve插装阀cartridge valve滑阀slide valve锥阀poppet valve阀芯valve element阀芯位置valve element position单向阀check valve液控单向阀pilot-controlled check valve 梭阀shuttle valve压力控制阀pressure relief valve溢流阀pressure relief valve顺序阀sequence valve减压阀pressure reducing平衡阀counterbalance valve卸荷阀unloading valve直动式directly operated type先导式pilot-operated type机械控制式mechanically controlled type 手动式manually operated type液控式hydraulic controlled type流量控制阀flow control valve固定节流阀fixed restrictive valve可调节流阀adjustable restrictive valve 单向节流阀one-way restrictive valve调速阀speed regulator valve分流阀flow divider valve集流阀flow-combining valve截止阀shut-off valve球阀global(ball) valve针阀needle valve闸阀gate valve膜片阀diaphragm valve蝶阀butterfly valve噪声等级noise level放大器amplifier模拟放大器analogue amplifier数字放大器digital amplifier传感器sensor阈值threshold伺服阀servo-valve四通阀four-way valve喷嘴挡板nozzle flapper液压放大器hydraulic amplifier颤振dither阀极性valve polarity流量增益flow gain对称度symmetry流量极限flow limit零位内泄漏null(quiescent) leakage 遮盖lap零遮盖zero lap正遮盖over lap负遮盖under lap开口opening零偏null bias零漂null drift阀压降valve pressure drop分辨率resolution频率响应frequency response幅值比amplitude ratio相位移phase lag传递函数transfer function管路flow line硬管rigid tube软管flexible hose工作管路working line回油管路return line补液管路replenishing line控制管路pilot line泄油管路drain line放气管路bleed line接头fitting；connection焊接式接头welded fitting扩口式接头flared fitting快换接头quick release coupling法兰接头flange connection弯头elbow异径接头reducer fitting流道flow pass油口port闭式油箱sealed reservoir油箱容量reservoir fluid capacity气囊式蓄能器bladder accumulator 空气污染air contamination固体颗粒污染solid contamination 液体污染liquid contamination空气过滤器air filter油雾气lubricator热交换器heat exchanger冷却器cooler加热器heater温度控制器thermostat消声器silencer双筒过滤器duplex filter过滤器压降filter pressure drop有效过滤面积effective filtration area公称过滤精度nominal filtration rating压溃压力collapse pressure填料密封packing seal机械密封mechanical seal径向密封radial seal旋转密封rotary seal活塞密封piston seal活塞杆密封rod seal防尘圈密封wiper seal；scraper组合垫圈bonded washer复合密封件composite seal弹性密封件elastomer seal丁腈橡胶nitrile butadiene rubber；NBR 聚四氟乙烯polytetrafluoroethene；PTFE 优先控制override control压力表pressure gauge压力传感器electrical pressure transducer 压差计differential pressure instrument液位计liquid level measuring instrument 流量计flow meter压力开关pressure switch脉冲发生器pulse generator液压泵站power station空气处理单元air conditioner unit压力控制回路pressure control circuit安全回路safety circuit差动回路differential circuit调速回路flow control circuit进口节流回路meter-in circuit。

液压类英语单词一、阀类Solenoid valve[ˈsəulinɔid vælv]电磁阀Check valve [tʃek vælv] 单向阀Cartridge valve [ˈkɑ:tridʒ vælv] 插装阀Sandwich plate valve [ˈsænwidʒ pleit vælv] 叠加阀Pilot valve [ˈpaɪlət vælv] 先导阀Pilot operated check valve[ˈpaɪlət 'ɒpəreɪtɪd tʃek vælv] 液控单向阀Sub-plate mount [sʌb plet maʊnt] 板式安装Manifold block [ˈmænəˌfold blɑk]集成块Pressure relief valve[ˈprɛʃɚ rɪˈlif vælv]压力溢流阀Flow valve [flo vælv] 流量阀Throttle valve[ˈθrɑtl: vælv] 节流阀Double throttle check valve [ˈdʌbəl ˈθrɑtl:tʃek vælv] 双单向节流阀Rotary knob [ˈrotəri nɑb]旋钮Rectifier plate [ˈrɛktəˌfaɪɚ plet] 节流板Servo valve [ˈsɚvo vælv] 伺服阀Proportional valve [prəˈpɔrʃənəl vælv] 比例阀Position feedback [pəˈzɪʃən ˈfidˌbæk]位置反馈Progressive flow [prəˈɡrɛsɪv flo]渐增流量De-energizing of solenoid ['də'enədʒaɪzɪŋ əvˈsoləˌnɔɪd]电磁铁释放二、介质类Phosphate ester (HFD-R) [ˈfɔsˌfeɪt ˈestə] 磷酸甘油酯Water-glycol (HFC) ['wɔtɚ'glaɪkoʊl]水-乙二醇Emulsion [ɪˈmʌlʃən]乳化液Inhibitor [ɪnˈhɪbɪtɚ]缓蚀剂Synthetic lubricating oil [sinˈθetik ˈlu:brikeitiŋ ɔil]合成油三、液压安装工程Contamination [kənˌtæmɪ'neɪʃən]污染Grout [ɡraʊt]灌浆Failure ['feɪljər]失效Jog [dʒɑɡ]点动Creep [krip] 爬行Abrasion [ə'breʒən]摩擦Retract [rɪˈtrækt]（活塞杆）伸出Extension [ɪkˈstɛnʃən]（活塞杆）缩回Malfunction [mælˈfʌŋkʃən]误动作Pickling ['pɪklɪŋ]酸洗Flushing [flʌʃɪŋ]冲洗Dipping process [ˈdipiŋ ˈprəuses]槽式酸洗Re-circulation [re-sɚkjəˈleʃən]循环Passivity [pæˈsɪvɪti] 钝化Nitric acid [ˈnaɪtrɪk ˈæsɪd] 柠檬酸Argon ['ɑrgɑn] 氩气Butt welding [bʌt ˈweldɪŋ]对接焊Socket welding [ˈsɔkit ˈweldɪŋ]套管焊Inert gas welding [ɪnˈɜ:t ɡæs ˈweldɪŋ] 惰性气体焊四、管接头Bite type fittings [baɪt taɪp 'fɪtɪŋs]卡套式管接头Tube to tube fittings [tub tu tub 'fɪtɪŋs]接管接头union [ˈjunjən]直通接管接头union elbow [ˈjunjən ˈɛlˌbo]直角管接头union tee [ˈjunjən ti] 三通管接头union cross [ˈjunjən krɔs]四通管接头Mal stud fittings [mɑ:l stʌd'fɪtɪŋs] 端直通管接头Bulkhead fittings [ˈbʌlkˌhɛd 'fɪtɪŋs]长直通管接头Weld fittings [wɛld fɪtɪŋs] 焊接式管接头Female connector fittings ['fimel kəˈnektər kəˈnektər]接头螺母Reducers extenders [rɪd'ju:səz ɪks'tendəz]变径管接头Banjo fittings [ˈbændʒo 'fɪtɪŋs]铰接式管接头Adjustable fittings/swivel nut [ə'dʒʌstəbl 'fɪtɪŋs] 旋转接头五、伺服阀及伺服系统性能参数Dynamic response [daiˈnæmik rɪˈspɑns]动态频响DDV-direct drive valve [di:di:vi:-dɪˈrɛkt draɪv vælv]直动式伺服阀NFPA-National Fluid Power Association ['næʃnəl 'fluɪd['paʊɚ] 美国流体控制学会Phase lag [fez læɡ]相位滞后Nozzle flapper valve [ˈnɑzəl ˈflæpɚ ]喷嘴挡板阀Servo-jet pilot valve ['sɝvo-dʒɛt ˈflæpɚ]射流管阀Dither [ˈdɪðɚ]颤振电流Coil impedance [kɔɪl ɪmˈpidns]线圈阻抗Flow saturation [fləʊˌsætʃəˈreʃən]流量饱和Linearity [ˌlɪnɪ'ærətɪ] 线形度Symmetry [ˈsɪmɪtri] 对称性Hysterics [hɪsˈtɛrɪks] 滞环Threshold['θrɛʃhold]灵敏度Lap [læp]滞后Pressure gain [ˈprɛʃɚɡen]压力增益Null [nʌl] 零位Null bias [nʌl ˈbaɪəs]零偏Null shift [nʌl ʃɪft]零飘Frequency response [ˈfrikwənsi rɪˈspɑns]频率响应Slope [slop]曲线斜坡Aability [əˈbɪlɪti]性能；能力load-carrying ability [lod-'kærɪɪŋ əˈbɪlɪti]承载能力absorber [əb'sɔːbə]吸收器；吸收剂；过滤器；减震器accessories [ək'sesərɪz] 辅件，附件，配件hydraulic accessories [haɪˈdrɔlɪk ək'sesərɪz] 液压辅件accumulate [əˈkjumjəˌlet] 储存；蓄能；累积accumulator [əˈkjumjəˌletɚ]蓄能器；蓄电池；累加器accuracy [ˈækjərəsi]准确性；精度action [ˈækʃən]作用；动作；作用力；行程actuated [ˈæktʃu:ˌeɪtid]操纵，控制directly actuated [dɪˈrɛktli ˈæktʃu:ˌeɪtid] 直接操纵的，直接控制的pilot actuated [ˈpaɪlət ˈæktʃu:ˌeɪtid] 先导控制的，液控的actuator 执行元件；液压缸；马达adapter [əˈdæptɚ]接头；衬套；压环；连接件pipe adapter[paɪp əˈdæptɚ] 管接头admission [ædˈmɪʃən] 供给，供油，供气alignment [əˈlaɪnmənt]找正，定心，对中amplifier [ˈæmpləˌfaɪɚ]放大器differential pressure amplifier [ˌdɪfəˈrɛnʃəl ˈprɛʃɚˈæmpləˌfaɪɚ]压差放大器flow amplifier [flo ˈæmpləˌfaɪɚ] 流量放大器assembly [əˈsɛmbli]组合，组件，机组axis [ˈæksɪs]轴Bback-flow ['bækfl'oʊ]回流back-up ['bæk'ʌp]支撑hydrostatic back-up [ˌhaɪdrə'stætɪk 'bæk'ʌp] 静压支撑barrel [ˈbærəl]桶，缸体base [bes] 底座；支座bearing [ˈbɛrɪŋ]支承；轴承；方位radial ball bearing [ˈrediəl bɔl ˈbɛrɪŋ]径向球轴承rolling bearing [ˈroʊlɪŋ ˈbɛrɪŋ] 滚动轴承sliding bearing [ˈslaɪdɪŋ ˈbɛrɪŋ] 滑动轴承thrust bearing [θrʌst ˈbɛrɪŋ]止推轴承bed [bɛd]台pump test bed [pʌmp test bɛd ]泵试验台behavior [bɪˈhevjɚ] 性能；工况bend [bɛnd]弯头；弯管blade [bled] 叶片flat blade [flæt bled]平面叶片forward inclined blade [ˈfɔrwəd ɪnˈklaɪnd bled]前倾叶片guide blade [ɡaɪd bled]导叶radial blade [ˈrediəl bled]径向叶片bleed [blid] 排气air bleed [er blid]排气阀bleeder ['bli:dər]排气孔block [blɑk]块；封闭；块体cartridge valve block [ˈkɑrtrɪdʒ vælv blɑk]插装阀块体choke block [tʃok blɑk]节流板directional control block [dɪˈrɛkʃənəl kənˈtrol blɑk]多路阀，方向控制阀组panel block[ˈpænəl blɑk]阀板组body [ˈbɑdi]体；缸筒；阀体，壳体pump body [pʌmp ˈbɑdi] 泵体tank body [tæŋk ˈbɔdi]箱体valve body [vælv ˈbɑdi]阀体bolt [bolt]螺栓；插销；螺杆boss [bɔs] 轮毂bottom [ˈbɑtəm]底；底部cylinder bottom [ˈsɪləndɚˈbɑtəm]缸底；缸后盖bracket[ˈbrækɪt]支架pump bracket [pʌmp ˈbrækɪt]泵架bubble-tight [brækɪt taɪt]气密的buffer [ˈbʌfɚ]缓冲器，阻尼器bush(ing) [bʊʃ（'bʊʃɪŋ )]套，导向套；衬套Ccap [kæp]帽,盖,罩,塞cylinder end cap[ˈsilində end kæp] 缸端盖cylinder head cap [ˈsilində hed kæp]缸前盖capacity [kəˈpæsɪti]容量;功率;排量;流量effective capacity [ɪˈfɛktɪv kəˈpæsɪti] 有效排量,实际排量geometric capacity [ˌdʒiəˈmɛtrɪk kəˈpæsɪti]几何排量,理论排量casing [ˈkesɪŋ]套,壳,罩gear casing [ɡɪr ˈkesɪŋ]齿轮箱，变速箱pump casing [pʌmp ˈkesɪŋ]泵体cavitation [ˌkævə'teɪʃən]气蚀cavity [ˈkævɪti]腔centering ['sentərɪŋ]中心调整，定心chamber [ˈtʃembɚ]腔，室；容积；油腔；气腔chamfer [ˈtʃembɚ]槽；倒角changement ['tʃeɪndʒmənt]换向机构characteristic [ˌkærəktəˈrɪstɪk]特性曲线；特征线charger [ˈtʃɑrdʒɚ] 加载装置charging ['tʃɑ:dʒɪŋ]充液；充压choke [tʃok]节流；节流口chord [kɔrd] 弦circlip ['sɜ:klɪp]弹性挡圈circuit ['sɜ:kɪt]回路clearance [ˈklɪərəns]间隙clog [klɔɡ]阻塞；堵塞cock [kɑk]龙头collar[ˈkɑlɚ]圈；法兰盘cushion collar [ˈkʊʃən ˈkɑlɚ]缓冲套locating collar [loʊ'kəɪtɪŋ ˈkɑlɚ] 定位凸缘套loose collar [lus ˈkɑlɚ]轴肩挡圈thrust collar[θrʌst ˈkɑlɚ] 止推环connection [kəˈnɛkʃən]连接；连接管路；接头consumption [kənˈsʌmpʃən] 消耗量cylinder [ˈsɪləndɚ]缸；液压缸Ddebugging ['di:'bʌgɪŋ]排除故障；调试deflation [dɪˈfleʃən]排气delivery [dɪˈlɪvəri]流量differential [ˌdɪfəˈrɛnʃəl]差动的；微分的displacement [dɪsˈplesmənt]压出；排出；排量；位移dowel[ˈdaʊəl]定位销drained [dreɪnd]泄油的duty [ˈduti]负载，功率；工况Eeffect [ɪˈfɛkt]作用;效应cavitate effect ['kævɪteɪt ɪˈfɛkt]气蚀效应choking effect [ˈtʃokɪŋ ɪˈfɛkt]节流作用elbow [ˈɛlˌbo]弯头electro-hydraulic [ɪ'lektroʊ-haɪˈdrɔlɪk] 电液的entrap [ɛnˈtræp]困油escape [ɪˈskep] 泄漏,逸出,排出etching[ˈɛtʃɪŋ]蚀刻;腐蚀gas etching [ɡæs ˈɛtʃɪŋ]气蚀exhaust [ɪɡˈzɔst]排泄;回油;Ffailure ['feɪljər] 故障;事故;损坏,失效fastener[ˈfæsnɚ]紧固件fatigue [fəˈtiɡ] 疲劳feedback [ˈfidˌbæk]反馈filler [ˈfɪlɚ] 加油口,注油口;填料;垫片filter[ˈfɪltɚ]滤油器flow [flo]流;液流;流程;流束;流量;流动nominal flow[ˈnɑmənəl] 公称流量rated flow [ˈreitid fləu] 额定流量stationary flow [ˈsteʃəˌnɛri flo] 定常流,定常流动streamline flow[ˈstrimˌlaɪn flo]层流turbulent flow [ˈtɚbjələnt flo] 紊流volume flow [ˈvɑljum flo]体积流量flowline [f'loʊlɪn]管路;流线flow-regulator [f'loʊlɪn-ˈrɛɡjəˌletɚ]流量调节阀fluctuation [ˌflʌktʃʊˈeʃən] 脉动fluid [ˈfluɪd] 流体,液体;射流hydraulic operating fluid [haɪˈdrɔlɪk ˈɑpəˌretɪŋ ˈfluɪd] 液压油incompressible fluid [ˌɪnkəmˈprɛsəbəl ˈfluɪd] 不可压缩流体frame [frem]座,架Ggain [ɡen] 增益flow gain [flo ɡen] 流量增益feedback gain [ˈfidˌbæk ɡen] 反馈增益gap [ɡæp]间隙,缝隙gear [ɡɪr]齿轮,装置,机构governing [ˈgʌvənɪŋ]调节,控制Hhead [hɛd] 缸头,头部;盖;水头;扬程cylinder head [ˈsɪləndɚ hɛd]缸头static head [ˈstætɪk hɛd] 静压头theoretic head [ˌθɪr'retɪk hɛd]理论能头total head [ˈtotl hɛd]总能头water head [ˈwɔtɚ hɛd]水头hole [hol]孔,洞air hole [er hol]气孔blind hole [blaɪnd hol]盲孔bolt hole [bolt hol]螺栓孔bose [boʊs]胶管,软管housing [ˈhaʊzɪŋ] 壳体;槽hub [hʌb]毂;衬套hydrostatics [ˌhaɪdrə'stætɪks]液压技术,液体静力学Iidling [ˈaidlɪŋ]空转impact [ˈɪmˌpækt]冲击,撞击impeller [ɪm'pelə]叶轮closed impeller [klozd ɪmˈpɛlɚ] 闭式叶轮open impeller [ˈopən ɪmˈpɛlɚ]开式叶轮pump impeller [pʌmp ɪmˈpɛlɚ]泵叶轮incidence [ˈɪnsɪdəns] 入射;入射角blade incidence [bled ˈɪnsɪdəns] 叶片安装角incompressible [ˌɪnkəm'presəbəl] 不可压缩的inlet [ˈɪnˌlɛt]进口;吸入intensifier[ɪnˈtɛnsəˌfaɪɚ] 增压器intensity [ɪnˈtɛnsɪti]强度Jjack [dʒæk] (柱塞)缸;千斤顶joint [dʒɔɪnt]接头;关节cross joint [krɔs dʒɔɪnt] 十字接头flange joint [flændʒ dʒɔɪnt]法兰式接头screwed joint [skru:d dʒɔint] 螺纹接头journal [ˈdʒɚnəl]轴颈jump [dʒʌmp]跳动;振动pressure jump [ˈprɛʃɚ dʒʌmp]压力突变Kkeyway ['ki:ˌweɪ] 键槽Llag [læɡ] 滞后;延迟servovalve phase lag [sɜ:vɒ'vælv fez læɡ] 伺服阀相位滞后laminar ['læmɪnə]层流的latch [lætʃ]插销;锁紧装置;锁定leak [lik] 漏;漏油;渗漏处;漏出物line [laɪn]管路;线路liner [ˈlaɪnɚ]衬套;导向套;内层胶liquid [ˈlɪkwɪd] 液体(的);液力的load [lod] 负载;载荷location [loˈkeʃən] 位置;定位;安装lock [lɑk] 锁;闭锁;液压卡紧loop [lup]环;环路;回路;循环control loop [kənˈtrol lup] 控制回路,调节回路main loop [men lup] 主回路servo loop [ˈsɚvo lup]伺服回路loss [lɔs] 损失bend loss [bɛnd lɔs] 弯头损失blade loss [bled lɔs]叶片损失line loss [laɪn lɔs] 管路损失local pressure loss [ˈlokəl ˈprɛʃɚ lɔs] 局部压力损失partial loss [ˈpɑrʃəl lɔs]局部损失lubricate[ˈlubrɪˌket]润滑lug [lʌɡ]耳轴lifting lug[ˈlɪftɪŋ lʌɡ] 吊环Mmandrel ['mændrəl]心轴;芯棒manometer [mə'nɒmətə] 压力机,压力表meter[ˈmitɚ]米;仪表;计量;节制;控制(流量);流量计meter-in [ˈmitɚ-ɪn]进口节流meter-out [ˈmitɚ-aʊt] 出口节流motion [ˈmoʃən] 动作alternative motion [ɔlˈtɚnətɪv ˈmoʃən] 往复运动lost motion [lɔst ˈmoʃən]空转synchronized motion ['sɪŋkrənaɪzd ˈmoʃən]同步运动motor [ˈmotɚ]发动机,液压马达axial piston motor [ˈæksiəl ˈpɪstən ˈmotɚ] 轴向柱塞马达bent axis piston motor [bɛnt ˈæksɪs ˈpɪstən ˈmotɚ]斜轴式轴向柱塞马达cam plate type axial piston motor [kæm plet taɪp ˈæksiəl ˈpɪstən ˈmotɚ] 斜盘式轴向柱塞马达constant displacement motor [ˈkɑnstənt dɪsˈplesmənt ˈmotɚ]定量马达radial motor [ˈrediəl ˈmotɚ] 径向马达sliding vane motor ['slaɪdɪŋ ven ˈmotɚ]叶片马达swing motor [swɪŋ ˈmotɚ]摆动马达Nnominal [ˈnɑmənəl] 额定的,公称的notch [nɑtʃ]凹槽relief notch [rɪˈlif nɑtʃ]卸荷槽null [nʌl]零位Ooff-load ['ɔ:fl'oʊd]卸荷oil [ɔɪl]油oiler ['ɔɪlə] 注油器olive [ˈɑlɪv]球面卡套grooved olive [gru:vd ˈɑlɪv]迷宫密封环operation [ˌɑpəˈreʃən]运行;操作;运算orifice [ˈɔrəfɪs]小孔;节流孔O-ring [oʊ rɪŋ] O型密封圈output [ˈaʊtˌpʊt] 输出;排量;流量overload [ˌovɚˈlod] 过载Ppack [pæk]包,捆;组合件,部件,单元power pack [ˈpaʊɚ pæk] 液压泵站package [ˈpækɪdʒ] 包,捆;组件,单元hydraulic package [haɪˈdrɔlɪk ˈpækɪdʒ] 液压泵站power package [ˈpaʊɚˈpækɪdʒ]泵站packing [ˈpækɪŋ] 密封;密封装置;填料密封pad [pæd] 衬垫;底座asbestos pad [æsˈbestəs pæd] 石棉垫valve pad [vælv pæd]阀垫parameter [pəˈræmɪtɚ]参数part [pɑ:rt] 部分;零件;部件partition [pɑrˈtɪʃən] 隔板passage [ˈpæsɪdʒ] 流道;通道;通过pedestal [ˈpɛdɪstəl] 支座,底座motor pedestal [ˈmotɚˈpɛdɪstəl] 电动机座phenomenon [fɪˈnɑməˌnɑn] 现象stick-alip phenomenon [stɪk əlæp fɪˈnɑməˌnɑn]爬行现象trapping phenomenon ['træpɪŋ fɪˈnɑməˌnɑn]困油现象piece [pis]零件,部件pilot(-actuate,-operate) [ˈpaɪlət-ˈæktʃuet / ˈpaɪlət-ˈɑpəˌret]先导控制;液控piloted ['paɪlətɪd]先导控制的pin [pɪn] 销;插头alignment pin [əˈlaɪnmənt pɪn]定位销cottar pin ['kɒtə pɪn]开口销locking pin [ˈlɑkɪŋ pɪn] 锁紧销piston pin [ˈpɪstən pɪn]活塞销straight pin [stret pɪn] 圆柱销pipe [paɪp]管子,管道(尤指铸铁管和钢管)piston [ˈpɪstən] 活塞;柱塞;阀芯double acting piston [ˈdʌbəl ˈæktɪŋ ˈpɪstən] 双作用活塞double rod piston [ˈdʌbəl rɑd ˈpɪstən]双杆活塞hollow piston [ˈhɑlo ˈpɪs tən]空心活塞single-rod piston [ˈsɪŋɡəl rɑd ˈpɪstən] 单杆活塞pit [pɪt]坑;槽pitch [pɪtʃ]节距pitting ['pɪtɪŋ]凹痕;锈斑;点蚀plug [plʌɡ]堵塞;阻塞;堵头air release plug [er rɪ'li:s plʌɡ] 排气塞plug-in [ˈplʌɡˌɪn]插入式的,组合式的poppet [ˈpɑpɪt]提动阀芯,座阀芯,锥阀芯,碟形阀芯pore [pɔr]孔;孔隙port [pɔrt] 油口;连接口position [pəˈzɪʃən] 位置;状态;定位center valve position [ˈsɛntɚ vælv pəˈzɪʃən]阀的中间位置neutral position [ˈnutrəl pəˈzɪʃən] 中位;零位three position [θ'ri:pəz'ɪʃn]三位two position [tu pəˈzɪʃən]二位pressure[ˈprɛʃɚ] 压力,压强;气压pulsation [pʌlˈseʃən] 脉动,波动pump [pʌmp]泵bent axis axial piston pump [bɛnt ˈæksɪs ˈæksiəl ˈpɪstən pʌmp] 斜轴式轴向柱塞泵booster pump [ˈbustɚ pʌmp]辅助泵,充液泵cam plate type axial piston pump [kæm plet taɪp ˈæksiəl ˈpɪstən pʌmp] 斜盘式轴向柱塞泵centrifugal pump [sɛnˈtrɪfjəɡəl pʌmp]离心泵constant delivery pump [ˈkɑnstənt dɪˈlɪvəri pʌmp]定量泵cycloid rotor pump ['saɪklɔɪd ˈrotɚ pʌmp] 摆线转子泵double action vane pump [ˈdʌbəl ˈækʃən ven pʌmp] 双作用叶片泵gear pump [ɡɪr pʌmp] 齿轮泵multi-stage pump [ˌmʌltɪ'steɪdʒ pʌmp]多级泵single action vane pump [ˈsɪŋɡəl ˈækʃən ven pʌmp] 单作用叶片泵vane pump [ven pʌmp] 叶片泵variable capacity pump [ˈvɛriəbəl kəˈpæsɪti pʌmp]变量泵Rrabbet ['ræbɪt] 球铰rack [ræk]齿条;机架racing[ˈreɪsɪŋ]空转radian[ˈrediən]弧度radius[ˈrediəs]半径range [rendʒ]范围,量程rated ['reɪtɪd]额定的regulation[ˌrɛɡjəˈleʃən] 调节,调整regulator [ˈrɛɡjəˌletɚ] 调节器,调压阀differential pressure regulator [ˌdɪfəˈrɛnʃəl ˈprɛʃɚˈrɛɡjəˌletɚ] 定差减压阀proportional pressure regulator [prəˈpɔrʃənəl ˈprɛʃɚˈrɛɡjəˌletɚ] 定比减压阀relay ['ri:leɪ]继电器relief [rɪˈlif]释压;溢流;卸荷reset[riˈsɛt]复位restriction [rɪˈstrɪkʃən]节流;阻尼,节流口,阻尼孔restrictor [rɪs'trɪktə]节流阀;节流口;阻尼孔reversal[rɪˈvə:səl]反转,倒转revolution [ˌrɛvəˈluʃən]旋转;转数rider[ˈraɪdɚ]导向套ring [rɪŋ]环,圈anti-extrusion ring [ˈæntaɪ-ɪkˈstruʒən rɪŋ]密封挡圈,挡圈back support ring [bæk səˈpɔrt rɪŋ]后支承环back-up ring [bæk ʌp rɪŋ]挡圈bearing ring[ˈbɛrɪŋ rɪŋ]导向套dust ring [dʌst rɪŋ] 防尘圈retainer ring [rɪˈtenɚ rɪŋ]卡环seal ring [sil rɪŋ] 密封圈;密封环rod [rɑd]杆;活塞杆Sscrew [skru]螺杆,螺钉,丝杆,螺旋seal [sil] 密封;封口;密封件;密封装置seat [sit] 阀座,座seizure [ˈsiʒɚ] 卡死,咬住,擦伤selector [sɪˈlɛktɚ]换向阀servo ['sɜ:rvoʊ]伺服;伺服机构,伺服系统servomotor ['sɜ:voʊ'moʊtə]伺服马达servopump [sɜ:vɒ'pʌmp] 伺服泵servovalve [sɜ:vɒ'vælv] 伺服阀set [sɛt]组件;定位;集合shaft [ʃæft]轴pump shaft [pʌmp ʃæft]泵轴sleeve [sliv]套;套管;卡套;阀套slot [slɑ:t]缝,隙,槽spring [sprɪŋ]弹簧stroke [strok]行程symbol [ˈsɪmbəl] 符号functional symbol [ˈfʌŋkʃənəl ˈsɪmbəl]职能符号Ttank [tæŋk]箱,缸;油箱;容器tee [ti]三通接头,三通throttle [ˈθrɑtl:] 节流;节流阀trapping ['træpɪŋ]困油travel[ˈtrævəl] 位移;行程tube [tub]管子(尤指有色金属和无缝钢管)tubeline [tjuː'bɪlaɪn]管路Uunion ['ju:nɪən]中间接头;直通接头Vvalve [vælv] 阀back pressure valve [bæk ˈprɛʃɚ vælv]背压阀bypass valve [ˈbaɪˌpæs vælv]旁通阀;溢流阀change valve [tʃendʒ vælv]换向阀check valve [tʃɛk vælv] 单向阀direct operated solenoid valve [dɪˈrɛkt 'ɒpəreɪtɪd ˈsoləˌnɔɪd vælv] 电磁阀flow regulating valve [fləu ˈreɡjuleitiŋ vælv]调速阀four port valve [fɔr pɔrt vælv] 四通阀four position valve [fɔr pəˈzɪʃən vælv] 四位阀hand operated valve [hænd 'ɒpəreɪtɪd vælv] 手动阀hydraulic operated check valve [haɪˈdrɔlɪk 'ɒpəreɪtɪd tʃɛk vælv]液控单向阀overflow valve [ˌovɚˈflo vælv] 溢流阀overload relief valve [ˌovɚˈlod rɪˈlif vælv]安全阀;过载溢流阀piloted valve ['paɪlətɪd vælv] 先导式阀vane [ven]叶片diffusion vane [dɪˈfjuʒən ven]导叶vent [vɛnt]放气;排气孔volume[ˈvɑljum]容积,体积displacement volume [dɪsˈplesmənt ˈvɑljum]排量Wwasher [ˈwɑʃɚ] 垫圈;衬垫wiper [ˈwaɪpɚ]防尘圈Zzone [zoʊn] 地带;区(域)dead zone [ded zəun]死区high pressure zone [hai ˈpreʃə zəun] 高压区low pressure zone [ləu ˈpreʃə zəun]低压区。

A ability 性能；能力load-carrying ability 承载能力absorber 吸收器；吸收剂；过滤器；减震器accessories 辅件，附件，配件hydraulic accessories 液压辅件accumulate 储存；蓄能；累积accumulator 蓄能器；蓄电池；累加器accuracy 准确性；精度action 作用；动作；作用力；行程actuated 操纵，控制directly actuated 直接操纵的，直接控制的pilot actuated 先导控制的，液控的actuator 执行元件；液压缸；马达adapter 接头；衬套；压环；连接件pipe adapter 管接头admission 供给，供油，供气alignment 找正，定心，对中amplifier 放大器differential pressure amplifier 压差放大器flow amplifier 流量放大器assembly 组合，组件，机组axis 轴C cap 帽,盖,罩,塞cylinder end cap 缸端盖cylinder head cap 缸前盖capacity 容量;功率;排量;流量effective capacity 有效排量,实际排量geometric capacity 几何排量,理论排量casing 套,壳,罩gear casing 齿轮箱，变速箱pump casing 泵体cavitation 气蚀cavity 腔B back-flow 回流back-up 支撑hydrostatic back-up 静压支撑barrel 桶，缸体base 底座；支座bearing 支承；轴承；方位radial ball bearing 径向球轴承rolling bearing 滚动轴承sliding bearing 滑动轴承thrust bearing 止推轴承bed 台pump test bed 泵试验台behavior 性能；工况bend 弯头；弯管blade 叶片flat blade 平面叶片forward inclined blade 前倾叶片guide blade 导叶radial blade 径向叶片bleed 排气air bleed 排气阀bleeder 排气孔block 块；封闭；块体cartridge valve block 插装阀块体choke block 节流板directional control block 多路阀，方向控制阀组panel block 阀板组body 体；缸筒；阀体，壳体pump body 泵体tank body 箱体valve body 阀体bolt 螺栓；插销；螺杆boss 轮毂bottom 底；底部cylinder bottom 缸底；缸后盖bracket 支架pump bracket 泵架bubble-tight 气密的buffer 缓冲器，阻尼器bush(ing) 套，导向套；衬套G gain 增益flow gain 流量增益centering中心调整，定心chamber腔，室；容积；油腔；气腔chamfer槽；倒角changement换向机构characteristic特性曲线；特征线charger加载装置charging充液；充压choke节流；节流口chord弦circlip弹性挡圈circuit回路clearance间隙clog阻塞；堵塞cock龙头collar圈；法兰盘cushion collar缓冲套locating collar定位凸缘套loose collar轴肩挡圈thrust collar止推环connection连接；连接管路；接头consumption消耗量Eeffect作用;效应cavitate effect气蚀效应choking effect节流作用elbow弯头electro-hydraulic电液的entrap困油escape泄漏,逸出,排出etching蚀刻;腐蚀gas etching气蚀exhaust排泄;回油;Ffailure故障;事故;损坏,失效fastener紧固件fatigue疲劳feedback反馈filler加油口,注油口;填料;垫片filter滤油器flow流;液流;流程;流束;流量;流动nominal flow公称流量rated flow额定流量stationary flow定常流,定常流动feedback gain反馈增益gap间隙,缝隙gear齿轮,装置,机构governing调节,控制Hhead缸头,头部;盖;水头;扬程cylinder head缸头static head静压头theoretic head理论能头total head总能头water head水头hole孔,洞air hole气孔blind hole盲孔bolt hole螺栓孔bose胶管,软管housing壳体;槽hub毂;衬套hydrostatics液压技术,液体静力学Iidling空转impact冲击,撞击impeller叶轮closed impeller闭式叶轮open impeller开式叶轮pump impeller泵叶轮incidence入射;入射角blade incidence叶片安装角incompressible不可压缩的inlet进口;吸入intensifier增压器intensity强度Jjack (柱塞)缸;千斤顶joint接头;关节cross joint十字接头flange joint法兰式接头screwed joint螺纹接头journal轴颈jump跳动;振动pressure jump压力突变Kkeyway键槽streamline flow层流turbulent flow紊流volume flow体积流量flowline管路;流线flow-regulator流量调节阀fluctuation脉动fluid流体,液体;射流hydraulic operating fluid液压油incompressible fluid不可压缩流体frame座,架cylinder缸；液压缸Ddebugging排除故障；调试deflation排气delivery流量differential差动的；微分的displacement压出；排出；排量；位移dowel定位销drained泄油的duty负载，功率；工况Mmandrel心轴;芯棒manometer压力机,压力表meter米;仪表;计量;节制;控制(流量);流量计meter-in进口节流meter-out出口节流motion动作alternative motion往复运动lost motion空转synchronized motion同步运动motor发动机,液压马达axial piston motor轴向柱塞马达bent axis piston motor斜轴式轴向柱塞马达cam plate type axial piston motor斜盘式轴向柱塞马达constant displacement motor定量马达radial motor径向马达sliding vane motor叶片马达swing motor摆动马达Llag滞后;延迟servovalve phase lag伺服阀相位滞后laminar层流的latch插销;锁紧装置;锁定leak漏;漏油;渗漏处;漏出物line管路;线路liner衬套;导向套;内层胶liquid液体(的);液力的load负载;载荷location位置;定位;安装lock锁;闭锁;液压卡紧loop环;环路;回路;循环control loop控制回路,调节回路main loop主回路servo loop伺服回路loss损失bend loss弯头损失blade loss叶片损失line loss管路损失local pressure loss局部压力损失partial loss局部损失lubricate润滑lug耳轴lifting lug吊环Sscrew螺杆,螺钉,丝杆,螺旋seal密封;封口;密封件;密封装置seat阀座,座seizure卡死,咬住,擦伤selector换向阀servo伺服;伺服机构,伺服系统servomotor伺服马达servopump伺服泵servovalve伺服阀set组件;定位;集合shaft轴pump shaft泵轴sleeve套;套管;卡套;阀套slot缝,隙,槽spring弹簧stroke行程symbol符号Nnominal额定的,公称的notch凹槽relief notch卸荷槽null零位Ooff-load卸荷oil油oiler注油器olive球面卡套grooved olive迷宫密封环operation运行;操作;运算orifice小孔;节流孔O-ring O型密封圈output输出;排量;流量overload过载Ppack包,捆;组合件,部件,单元power pack液压泵站package包,捆;组件,单元hydraulic package液压泵站power package泵站packing密封;密封装置;填料密封pad衬垫;底座asbestos pad石棉垫valve pad阀垫parameter参数part部分;零件;部件partition隔板passage流道;通道;通过pedestal支座,底座motor pedestal电动机座phenomenon现象stick-alip phenomenon爬行现象trapping phenomenon困油现象piece零件,部件pilot(-actuate,-operate)先导控制;液控piloted先导控制的pin销;插头alignment pin定位销cottar pin开口销locking pin锁紧销functional symbol职能符号Ttank箱,缸;油箱;容器tee三通接头,三通throttle节流;节流阀trapping困油travel位移;行程tube管子(尤指有色金属和无缝钢管)tubeline管路Uunion中间接头;直通接头Vvalve阀back pressure valve背压阀bypass valve旁通阀;溢流阀change valve换向阀check valve单向阀direct operated solenoid valve电磁阀flow regulating valve调速阀four port valve四通阀four position valve四位阀hand operated valve手动阀hydraulic operated check valve液控单向阀overflow valve溢流阀overload relief valve安全阀;过载溢流阀piloted valve先导式阀vane叶片diffusion vane导叶vent放气;排气孔volume容积,体积displacement volume排量Wwasher垫圈;衬垫wiper防尘圈Zzone地带;区(域)piston pin活塞销straight pin圆柱销pipe管子,管道(尤指铸铁管和钢管)piston活塞;柱塞;阀芯double acting piston双作用活塞double rod piston双杆活塞hollow piston空心活塞single-rod piston单杆活塞pit坑;槽pitch节距pitting凹痕;锈斑;点蚀plug堵塞;阻塞;堵头air release plug排气塞plug-in插入式的,组合式的poppet提动阀芯,座阀芯,锥阀芯,碟形阀芯pore孔;孔隙port油口;连接口position位置;状态;定位center valve position阀的中间位置neutral position中位;零位three position三位two position二位pressure压力,压强;气压pulsation脉动,波动pump泵bent axis axial piston pump斜轴式轴向柱塞泵booster pump辅助泵,充液泵cam plate type axial piston pump斜盘式轴向柱塞泵centrifugal pump离心泵constant delivery pump定量泵cycloid rotor pump摆线转子泵double action vane pump双作用叶片泵gear pump齿轮泵multi-stage pump多级泵single action vane pump单作用叶片泵vane pump叶片泵variable capacity pump变量泵一、阀类dead zone死区high pressure zone高压区low pressure zone低压区revolution旋转;转数rider导向套ring环,圈anti-extrusion ring密封挡圈,挡圈back support ring后支承环back-up ring挡圈bearing ring导向套dust ring防尘圈retainer ring卡环seal ring密封圈;密封环rod杆;活塞杆Rrabbet球铰rack齿条;机架racing空转radian弧度radius半径range范围,量程rated额定的regulation调节,调整regulator调节器,调压阀differential pressure regulator定差减压阀proportional pressureregulator定比减压阀relay继电器relief释压;溢流;卸荷reset复位restriction节流;阻尼,节流口,阻尼孔restrictor节流阀;节流口;阻尼孔reversal反转,倒转Pressure gain压力增益Null零位Null bias零偏Null shift零飘Frequency response频率响应 Slope曲线斜坡Threshold灵敏度union cross四通管接头Mal stud fittings端直通管接头 Bulkhead fittings长直通管接头Solenoid valve电磁阀Check valve单向阀Cartridge valve插装阀Sandwich plate valve叠加阀 Pilot valve先导阀Pilot operated check valve液控单向阀Sub-plate mount板式安装Manifold block集成块Pressure relief valve压力溢流阀Flow valve流量阀Throttle valve节流阀Double throttle check valve双单向节流阀Rotary knob旋钮Rectifier plate节流板Servo valve伺服阀Proportional valve比例阀Position feedback位置反馈Progressive flow渐增流量De-energizing of solenoid电磁铁释放二、介质类Phosphate ester (HFD-R)磷酸甘油酯Water-glycol (HFC)水-乙二醇 Emulsion乳化液Inhibitor缓蚀剂Synthetic lubricating oil合成油三、液压安装工程Contamination污染Grout灌浆Failure失效Jog点动Creep爬行Abrasion摩擦Retract（活塞杆）伸出Extension（活塞杆）缩回Malfunction误动作Pickling酸洗Flushing冲洗Dipping process槽式酸洗Re-circulation循环Passivity钝化Weld fittings焊接式管接头Female connector fittings接头螺母Reducers extenders变径管接头Banjo fittings铰接式管接头Adjustable fittings/swivel nut旋转接头五、伺服阀及伺服系统性能参数Dynamic response动态频响DDV-direct drive valve直动式伺服阀NFPA-National Fluid Power Association美国流体控制学会Phase lag相位滞后Nozzle flapper valve喷嘴挡板阀Servo-jet pilot valve射流管阀 Dither颤振电流Coil impedance线圈阻抗Flow saturation流量饱和Linearity线形度Symmetry对称性Hysterics滞环Lap滞后四、管接头Bite type fittings卡套式管接头Tube to tube fittings接管接union直通接管接头union elbow直角管接头union tee三通管接头Nitric acid柠檬酸Argon氩气Butt welding对接焊Socket welding套管焊Inert gas welding惰性气体焊。

液压专业英语词汇流体传动 hydraulic power液压技术 hydraulics液力技术 hydrodynamics气液技术 hydropneumatics运行工况 operating conditions额定工况 rated conditions极限工况 limited conditions瞬态工况 instantaneous conditions稳态工况 steady-state conditions许用工况 acceptable conditions连续工况 continuous working conditions 实际工况 actual conditions效率 efficiency旋转方向 direction of rotation公称压力 nominal pressure工作压力 working pressure进口压力 inlet pressure出口压力 outlet pressure压降 pressure drop；differential pressure 背压 back pressure启动压力 breakout pressure充油压力 charge pressure开启压力 cracking pressure峰值压力 peak pressure运行压力 operating pressure耐压试验压力 proof pressure冲击压力 surge pressure静压力 static pressure系统压力 system pressure控制压力 pilot pressure充气压力 pre-charge pressure吸入压力 suction pressure调压偏差 override pressure额定压力 rated pressure耗气量 air consumption泄漏 leakage内泄漏 internal leakage外泄漏 external leakage层流 laminar flow紊流 turbulent flow气穴 cavitation流量 flow rate排量 displacement额定流量 rated flow 供给流量 supply flow流量系数 flower factor滞环 hysteresis图形符号 graphical symbol液压气动元件图形符号 symbols for hydrau lic and pneumatic components流体逻辑元件图形符号 symbols for fluid lo gic devices逻辑功能图形符号 symbols for logic functi ons回路图 circuit diagram压力－时间图 pressure time diagram功能图 function diagram循环 circle自动循环 automatic cycle工作循环 working cycle循环速度 cycling speed工步 phase停止工步 dwell phase工作工步 working phase快进工步 rapid advance phase快退工步 rapid return phase频率响应 frequency response重复性 repeat ability复现性 reproducibility漂移 drift波动 ripple线性度 linearity线性区 linear region液压锁紧 hydraulic lock液压卡紧 sticking变量泵 variable displacement pump泵的控制 control of pump齿轮泵 gear pump叶片泵 vane pump柱塞泵 piston pump轴向柱塞泵 axial piston pump法兰安装 flange mounting底座安装 foot mounting液压马达 hydraulic motor刚度 stiffness中位 neutral position零位 zero position自由位 free position缸 cylinder有杆端 rod end无杆端 rear end外伸行程 extend stroke内缩行程 retract stroke缓冲 cushioning工作行程 working stroke负载压力 induced pressure输出力 force实际输出力 actual force单作用缸 single-acting cylinder双作用缸 double-acting cylinder差动缸 differential cylinder伸缩缸 telescopic cylinder阀 valve底板 sub-plate油路块 manifold block板式阀 sub-plate valve叠加阀 sandwich valve插装阀 cartridge valve滑阀 slide valve锥阀 poppet valve阀芯 valve element阀芯位置 valve element position单向阀 check valve液控单向阀 pilot-controlled check valve 梭阀 shuttle valve压力控制阀 pressure relief valve溢流阀 pressure relief valve顺序阀 sequence valve减压阀 pressure reducing valve平衡阀 counterbalance valve卸荷阀 unloading valve直动式 directly operated type先导式 pilot-operated type机械控制式 mechanically controlled type 手动式 manually operated type液控式 hydraulic controlled type流量控制阀 flow control valve固定节流阀 fixed restrictive valve可调节流阀 adjustable restrictive valve 单向节流阀 one-way restrictive valve调速阀 speed regulator valve分流阀 flow divider valve集流阀 flow-combining valve截止阀 shut-off valve球阀 global(ball) valve 针阀 needle valve闸阀 gate valve膜片阀 diaphragm valve蝶阀 butterfly valve噪声等级noise level放大器 amplifier模拟放大器 analogue amplifier数字放大器 digital amplifier传感器 sensor阈值 threshold伺服阀 servo-valve四通阀 four-way valve喷嘴挡板 nozzle flapper液压放大器 hydraulic amplifier颤振 dither阀极性 valve polarity流量增益 flow gain对称度 symmetry流量极限 flow limit零位内泄漏 null(quiescent) leakage 遮盖 lap零遮盖 zero lap正遮盖 over lap负遮盖 under lap开口 opening零偏 null bias零漂 null drift阀压降 valve pressure drop分辨率 resolution频率响应 frequency response幅值比 amplitude ratio相位移 phase lag传递函数 transfer function管路 flow line硬管 rigid tube软管 flexible hose工作管路 working line回油管路 return line补液管路 replenishing line控制管路 pilot line泄油管路 drain line放气管路 bleed line接头 fitting；connection焊接式接头 welded fitting扩口式接头 flared fitting快换接头 quick release coupling法兰接头 flange connection弯头 elbow异径接头 reducer fitting流道 flow pass油口 port闭式油箱 sealed reservoir油箱容量 reservoir fluid capacity气囊式蓄能器bladder accumulator空气污染 air contamination固体颗粒污染 solid contamination液体污染 liquid contamination空气过滤器 air filter油雾气 lubricator热交换器 heat exchanger冷却器 cooler加热器 heater温度控制器 thermostat消声器 silencer双筒过滤器 duplex filter过滤器压降 filter pressure drop有效过滤面积 effective filtration area公称过滤精度 nominal filtration rating压溃压力 collapse pressure填料密封 packing seal机械密封 mechanical seal径向密封 radial seal旋转密封 rotary seal活塞密封 piston seal活塞杆密封 rod seal防尘圈密封 wiper seal；scraper组合垫圈 bonded washer复合密封件 composite seal弹性密封件 elastomer seal丁腈橡胶 nitrile butadiene rubber；NBR 聚四氟乙烯 polytetrafluoroethene；PTFE 优先控制 override control压力表 pressure gauge压力传感器 electrical pressure transducer 压差计 differential pressure instrument液位计 liquid level measuring instrument 流量计 flow meter压力开关 pressure switch脉冲发生器 pulse generator液压泵站 power station空气处理单元 air conditioner unit压力控制回路 pressure control circuit安全回路 safety circuit差动回路 differential circuit 调速回路 flow control circuit进口节流回路 meter-in circuit出口节流回路 meter-out circuit同步回路 synchronizing circuit开式回路 open circuit闭式回路 closed circuit管路布置 pipe-work管卡 clamper联轴器 drive shaft coupling操作台 control console控制屏 control panel避震喉 compensator粘度 viscosity运动粘度 kinematic viscosity密度 density含水量 water content闪点 flash point防锈性 rust protection抗腐蚀性 anti-corrosive quality便携式颗粒检测仪 portable particle counte rSolenoid valve 电磁阀Check valve 单向阀Cartridge valve 插装阀Sandwich plate valve 叠加阀Pilot valve 先导阀Pilot operated check valve 液控单向阀Sub-plate mount 板式安装Manifold block 集成块Pressure relief valve 压力溢流阀Flow valve 流量阀Throttle valve 节流阀Double throttle check valve 双单向节流阀Rotary knob 旋钮Rectifier plate 节流板Servo valve 伺服阀Proportional valve 比例阀Position feedback 位置反馈Progressive flow 渐增流量De-energizing of solenoid 电磁铁释放二、介质类Phosphate ester (HFD-R) 磷酸甘油酯Water-glycol (HFC) 水-乙二醇Emulsion 乳化液Inhibitor缓蚀剂Synthetic lubricating oil 合成油三、液压安装工程Contamination 污染Grout 灌浆Failure 失效Jog 点动Creep爬行Abrasion 摩擦Retract（活塞杆）伸出Extension （活塞杆）缩回Malfunction 误动作Pickling 酸洗Flushing 冲洗Dipping process 槽式酸洗Re-circulation 循环Passivity 钝化Nitric acid 柠檬酸Argon 氩气Butt welding 对接焊Socket welding 套管焊Inert gas welding 惰性气体焊四、管接头Bite type fittings 卡套式管接头Tube to tube fittings 接管接头union 直通接管接头union elbow 直角管接头union tee 三通管接头union cross 四通管接头Mal stud fittings 端直通管接头Bulkhead fittings 长直通管接头Weld fittings 焊接式管接头Female connector fittings 接头螺母Reducers extenders 变径管接头Banjo fittings 铰接式管接头Adjustable fittings/swivel nut 旋转接头五、伺服阀及伺服系统性能参数Dynamic response 动态频响DDV-direct drive valve 直动式伺服阀NFPA-National Fluid Power Association 美国流体控制学会Phase lag 相位滞后Nozzle flapper valve 喷嘴挡板阀Servo-jet pilot valve 射流管阀Dither 颤振电流Coil impedance 线圈阻抗Flow saturation 流量饱和Linearity 线形度Symmetry 对称性Hysterics 滞环Threshold 灵敏度Lap 滞后Pressure gain 压力增益Null 零位Null bias 零偏Null shift 零飘Frequency response 频率响应Slope 曲线斜坡液压系统（hydraulic system）执行元件（actuator）液压缸（cylinder）液压马达（motor）液压回路（circuit）压力控制回路（pressure control）流量（速度）控制回路（speed control）方向控制回路（directional valve control）安全回路（security control）定位回路（position control）同步回路（synchronise circuit）顺序动作回路（sequeunt circuit）液压泵（pump）阀（valve）压力控制阀（pressure valve）、流量控制阀（flow valve）方向控制阀（directional valve）液压辅件（accessory）普通阀（common valve）插装阀（cartridge valve）叠加阀（superimposed valve。