Zytel PA66 70G13HS1L NC010 物性表

PA66物性数据PA66物性数据是指聚酰胺66（Polyamide 66）的物理性质和化学性质的数据。

聚酰胺66是一种热塑性高分子材料，具有优异的力学性能、热稳定性和耐化学性能，被广泛应用于汽车、电子、纺织、机械等领域。

以下是一些常见的PA66物性数据：1. 密度：PA66的密度通常在1.10-1.15 g/cm³之间，具体数值取决于材料的配方和加工条件。

2. 熔融温度：PA66的熔融温度约为250-265℃，这使得它适用于高温环境下的应用。

3. 玻璃化转变温度：PA66的玻璃化转变温度约为50-60℃，这是材料从玻璃态转变为橡胶态的温度。

4. 拉伸强度：PA66的拉伸强度通常在60-80 MPa之间，具体数值取决于材料的配方和加工条件。

5. 弯曲强度：PA66的弯曲强度通常在80-100 MPa之间，具体数值取决于材料的配方和加工条件。

6. 弹性模量：PA66的弹性模量通常在2000-3000 MPa之间，具体数值取决于材料的配方和加工条件。

7. 热膨胀系数：PA66的热膨胀系数通常在70-90×10^-6/℃之间，具体数值取决于材料的配方和加工条件。

8. 湿水吸收率：PA66的湿水吸收率通常在2-3%之间，这意味着在湿润环境中，材料会吸收一定量的水分。

9. 耐化学性：PA66具有良好的耐化学性，能够抵抗酸、碱、溶剂等化学物质的侵蚀。

10. 热稳定性：PA66具有较好的热稳定性，能够在高温环境下保持其物理性能和化学性能。

需要注意的是，以上数据仅为参考值，具体数值会受到材料的配方、加工工艺以及测试方法的影响。

在实际应用中，建议根据具体需求进行材料选择和性能测试。

HTN501 NC010 is a 30% glass reinforced, flame retardant, lubricated high performance polyamide HTN501 NC010DuPont ™ Zytel ®HTNhigh performance polyamide resinZytel ®ValueDAM50%RHIdentification Part Marking Code ISO 11469>PA6T/XT-GF35FR< Part Marking Code SAE J1344>PPA-GF35FR<Mechanical Stress at Break ISO 527MPa (kpsi)165 (24) Strain at Break ISO 527% 1.6 Tensile Modulus ISO 527MPa (kpsi)13000 (1885) Shear Strength ASTM D 732MPa (kpsi)64 (9.3)70 (10) Flexural Modulus ISO 178MPa (kpsi)12000 (1740)12000 (1740) Flexural Strength ISO 178MPa (kpsi)250 (36)235 (34)Compressive Strength ASTM D 695MPa (kpsi)293 (42.6) Compressive ModulusASTM D 695MPa (kpsi)3580 (520)Notched Charpy Impact Strength ISO 179/1eAkJ/m2-30°C (-22°F)13 23°C (73°F)11 Unnotched Charpy Impact Strength ISO 179/1eUkJ/m2-30°C (-22°F)30 23°C (73°F)40Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm. Test temperatures are 23°C unless otherwise stated.The DuPont Oval Logo, DuPont™, The miracles of science™ and Zytel® are trademarks or registered trademarks of DuPont Company. Copyright© 2008080505/080804The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated; these data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations in actual end-use conditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in thispublication is to be considered as a license to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent counsel for a freedom to practice opinion on the intended application or end-use of our products. CAUTION: Do not use DuPont materials in medical application involving implantation in the human body or contact with internal body fluids or tissues unless the material has been provided from DuPont undera written contract that is consistent with DuPont policy regarding medical applications and expressly acknowledges the contemplated use. For further information, please contact your DuPont representative. You may also request a copy of DuPont POLICY Regarding Medical Applications H-50103-3 and DuPont CAUTION Regarding Medical Applications … H-50102-3Zytel ®resin. It is also a PPA resin.PropertyTest Method UnitsDuring molding, use proper protective equipment and adequate ventilation. Avoid exposure to fumes and limit the hold up time and temperature of the resin in the machine. Purge degraded resin carefully with HDPE.Zytel®ValueDAM50%RHThermalDeflection Temperature ISO 75-1/-2 °C (°F)0.45MPa 270 (518) 1.80MPa260 (500)Melting Temperature ISO 11357-1/-3 °C (°F)10°C/min, First Heat 300 (574)CLTE, Parallel ISO 11359-1/-2E-4/C (E-4/F)-40 - 23°C (-40 - 73°F)0.20 (0.11) 23 - 55°C (73 - 130°F)0.18 (0.10) 55 - 125°C (131 - 257°F)0.18 (0.10)CLTE, Normal ISO 11359-1/-2E-4/C (E-4/F)-40 - 23°C (-40 - 73°F)0.46 (0.26) 23 - 55°C (73 - 130°F)0.50 (0.28) 55 - 125°C (131 - 257°F)0.60 (0.33)Glass Transition Temperature DMA °C (°F)140 (284)90 (194)Electrical Surface Resistivity IEC 60093ohm 1E13 Volume Resistivity IEC 60093ohm m >1E131E13 Electric Strength IEC 60243-1kV/mm (V/mil)1.0mm34 (863)34 (863)Relative Permittivity IEC 602501E2 Hz 3.9 1E3 Hz 3.8 1E6 Hz 3.6Dissipation Factor IEC 60250E-41E2 Hz 80 1E3 Hz 130 1E6 Hz 150Arc Resistance ASTM D 495s 80 CTIIEC 60112V 525Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm. Test temperatures are 23°C unless otherwise stated.The DuPont Oval Logo, DuPont™, The miracles of science™ and Zytel® are trademarks or registered trademarks of DuPont Company. Copyright© 2008080505/080804The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated; these data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations in actual end-use conditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in thispublication is to be considered as a license to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent counsel for a freedom to practice opinion on the intended application or end-use of our products. CAUTION: Do not use DuPont materials in medical application involving implantation in the human body or contact with internal body fluids or tissues unless the material has been provided from DuPont undera written contract that is consistent with DuPont policy regarding medical applications and expressly acknowledges the contemplated use. For further information, please contact your DuPont representative. You may also request a copy of DuPont POLICY Regarding Medical Applications H-50103-3 and DuPont CAUTION Regarding Medical Applications … H-50102-3PropertyTest Method UnitsHTN501 NC010Zytel®ValueDAM50%RHFlammabilityFlammability Classification UL940.81mm V-0Oxygen Index ISO 4589-1/-2%37Hot Wire Ignition UL 746As0.81mm >150 1.5mm >150 3.0mm>150Temperature Index RTI, Electrical UL 746B°C0.81mm 150 1.5mm 150 3.0mm 150RTI, Impact UL 746B°C0.81mm 120 1.5mm 125 3.0mm 130RTI, Strength UL 746B°C0.81mm 130 1.5mm 130 3.0mm150Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm. Test temperatures are 23°C unless otherwise stated.The DuPont Oval Logo, DuPont™, The miracles of science™ and Zytel® are trademarks or registered trademarks of DuPont Company. Copyright© 2008080505/080804The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated; these data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations in actual end-use conditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in thispublication is to be considered as a license to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent counsel for a freedom to practice opinion on the intended application or end-use of our products. CAUTION: Do not use DuPont materials in medical application involving implantation in the human body or contact with internal body fluids or tissues unless the material has been provided from DuPont undera written contract that is consistent with DuPont policy regarding medical applications and expressly acknowledges the contemplated use. For further information, please contact your DuPont representative. You may also request a copy of DuPont POLICY Regarding Medical Applications H-50103-3 and DuPont CAUTION Regarding Medical Applications … H-50102-3PropertyTest Method UnitsHTN501 NC010Zytel®ValueDAM 50%RHOther DensityISO 1183kg/m 3 (g/cm 3)1680 (1.68)Hardness, Rockwell ASTM D 785Scale M 108 Scale R 124Taber AbrasionASTM D 1044mgCS-17 Wheel, 1kg, 1000 cycles 57Water Absorption ASTM D 570%Immersion 24h 0.25Molding Shrinkage ISO 294-4%Normal, 2.0mm 0.5 Parallel, 2.0mm 0.2ProcessingMelt Temperature Range °C (°F)320-330 (610-625) Mold Temperature Range °C (°F)140-160 (280-320)Drying Time, Dehumidified Dryer h 6-8 Drying Temperature°C (°F)100 (210) Processing Moisture Content%<0.10Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm. Test temperatures are 23°C unless otherwise stated.The DuPont Oval Logo, DuPont™, The miracles of science™ and Zytel® are trademarks or registered trademarks of DuPont Company. Copyright© 2008080505/080804The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated; these data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations in actual end-use conditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in thispublication is to be considered as a license to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent counsel for a freedom to practice opinion on the intended application or end-use of our products. CAUTION: Do not use DuPont materials in medical application involving implantation in the human body or contact with internal body fluids or tissues unless the material has been provided from DuPont undera written contract that is consistent with DuPont policy regarding medical applications and expressly acknowledges the contemplated use. For further information, please contact your DuPont representative. You may also request a copy of DuPont POLICY Regarding Medical Applications H-50103-3 and DuPont CAUTION Regarding Medical Applications … H-50102-3PropertyTest Method Units HTN501 NC010。

尼龙66的主要牌号与性能01.3.6.1国产尼龙66的主要性能指标国内生产尼龙66的厂家有：黑龙江省尼龙厂、上海塑料制品十八厂、辽阳化纤工业总公司、太原合成纤维厂、神马集团、浙江衢州化工厂、宜兴太湖尼龙厂、江苏海安化工厂。

其产品主要用制造各种机械、汽车、化工、电子电气装置的零部件，特别适合用于高强度或耐磨部件，如各种齿轮、滑轮、辊轴、轴承、泵体中叶轮、风箱叶片、高压密封圈、阀座、垫片、衬套、各种壳体、工具手柄、支撑架、电缆包层、汽车灯罩等。

在电子仪器设备、继电器等电气设备中制造零件、电梯导轨、建筑装饰扶手等。

在医疗器械、体育用品和日用品上也有广泛应用，如棒球棒、滑雪板等。

也可制成薄膜后与铝箔等形成复合膜用于食品包装，如软包装饮料、罐头等。

表01-73列出了几家企业的尼龙66产品指标。

表01-73 国产尼龙66的性能指标01.3.6.2阻燃增强尼龙66的主要性能指标目前，国内尚有许多厂家从事改性尼龙66树脂的生产。

生产阻燃尼龙66和阻燃增强尼龙66的主要厂家有：黑龙江省尼龙厂、黑龙江省化工研究所、上海赛璐珞厂、广州莲花山工程塑料厂、江阴市永建化工有限公司等。

阻燃尼龙66主要用于低压电器、机床电器、广播电视工业中，制造各种阻燃零件如调压器开关、仪器仪表外壳和电子电气连接器等；生产玻纤增强尼龙66的主要厂家有：黑龙江省尼龙厂、上海德胜塑料厂、广州莲花山工程塑料厂、苏州塑料一厂等。

产品主要应用于低压电器工业，如交流接触器底座、线圈骨架、行程开关等各种要求耐火性能的介电零件中。

黑龙江省化学研究所还生产防老化尼龙。

其主要指标列于表01-74中。

表01-74 国产改性尼龙66树脂的主要性能指标指标阻燃尼龙66 阻燃增强尼龙66 防老化尼龙66 玻纤增强尼龙66熔点，℃245～250 247～250 250～260相对密度 1.42～1.45 1.50 1.10～1.15 1.39吸水率，% <0.5 ≤1.0拉伸强度，MPa ≥60 120 ≥60 ≥162弯曲强度，MPa ≥100 180 ≥90 ≥196缺口冲击强度，kJ/m2≥5 10 ≥5 ≥9.8热变形温度（1.8MPa），℃60 220 60 ≥220阻燃等级，UL94 V-0 V-0体积电阻率，Ω·cm ≥10151013 ≥1.5×1015≥1014介电常数<5 5 4.4击穿电压，kV/mm ≥17 17 20 20模后收缩率，% 0.5～1.2 0.5～1.0 0.8～1.5玻纤含量，% 30±2 30±2弯曲弹性模量，MPa ≥5.4×103耐老化性能，倍>3表面电阻率，Ω≥101301.3.6.3杜邦公司系列尼龙66产品的基本性能指标杜邦公司是主要的尼龙66生产厂家之一，其产品型号齐全，覆盖面广，满足各行各业对尼龙66树脂的不同性能要求，见表01-75。

PA66 101 L美国杜邦Zytel材料用于注射成型的尼龙66材料。

T eL :I88,I9II,8 II2；东莞向阳塑胶可，亻共，原厂进口PA66材料以及材料物理性能和加工参数！规格级别：注塑级用途概述:广泛用于制造机械、汽车、化学与电气装置的零件，如齿轮、滚子、滑轮、辊轴、泵体中叶轮、风扇叶片、高压密封围、阀座、垫片、衬套、各种把手、支撑架、电线包层等。

亦可制成薄膜用作包装材料。

此外，还可用于制作医疗器械、日用品等。

另外有：PA66塑胶原料；加碳纤PA66；耐高温PA66；医疗级PA66；无卤阻燃PA66；改性塑料PA66；导电PA66；环保PA66；高抗冲击PA66；PA66价格；耐油性PA66；高刚性PA66；PA66抗UV；无溴PA66；抗紫外线PA66；加玻纤PA66；PA66 Zytel 101L性能特点：PA66是PA系列中机械强度最高、应用最广的品种,因其结晶度高,故其刚性、耐热性都较高超声波可焊接低分子量经润滑可加工性良好良好的成型性能良好的电气性能流动性高耐化学性良好耐磨损性良好耐疲劳性能耐油性能耐油脂性能生产阶段快脱模性能良好等;用途：汽车领域的应用电气/电子应用领域家电部件连接器;PA66能耐酸、碱、大多数无机盐水溶液、卤代烷、烃类、酯类、酮类等腐蚀，但易溶于苯酚、甲酸等极性溶剂。

具有优良的耐磨性、自润滑性，机械强度较高。

但吸水性较大，因而标准稳定性较差。

广泛用于制造机械、汽车、化学与电气设备的零件，如齿轮、滚子、滑轮、辊轴、泵体中叶轮、电扇叶片、高压密封围、阀座、垫片、衬套、各种把手、支撑架、电线包层等。

PA66 美国杜邦101L70G33L 尼龙66 抗蠕变性能，用于电器元件，汽车应用;101 尼龙66 耐化学腐蚀性;超好电气性能适用细丝101L 尼龙66 成型周期快;高抗疲劳性; 用于电器元件101F 尼龙66 快速成型周期;抗疲劳性强70G13HS1L 尼龙66 耐热稳定性，用于汽运;工程机械配件;70G13L 尼龙66 可利超声波焊接性用于电器元件，汽车应用;73G15HSL 尼龙6 高耐燃油，强抗疲劳性用于电器元件，工程机械;73G30HSL 尼龙66 高耐燃油，强抗疲劳性，良好的化学河70G43HSLA 尼龙66 高耐燃油，抗疲劳性73G50HSLA 尼龙6 耐热性稳定，润滑型70G25HSLR 尼龙66 耐寒抗冻性好，抗疲劳性强70G30HSLR 尼龙66 耐寒抗冻性好，抗疲劳性强70K20HSL 尼龙66 高耐磨性，耐热稳定70G33L NC010 尼龙66 强抗蠕变性能，用于电器元件，汽车应用;70G35HSL 高抗疲劳性，耐燃油性```70G35HSLRA4 耐寒抗冻性强，抗疲劳体```70G35HSRX70G43HSLA 高耐燃油，抗疲劳性```70G43L强抗蠕变性能，润滑性```70G50HSLA 高耐燃油，抗疲劳性```70K20HSL高耐磨性，耐热稳定，RoHS 合规性外观：自然色形状：颗粒料；性状：半透明或不透明乳白色结晶形聚合物，具有可塑性。

DuPont ™ Zytel®nylon resinZytel ®70G33L NC010ValueDAM 50%RHIdentification Resin Identification ISO 1043PA66-GF33 Part Marking Code ISO 11469>PA66-GF33<Mechanical Stress at Break ISO 527MPa (kpsi)200 (29.0)140 (20.3)Strain at Break ISO 527% 3.55 Tensile Modulus ISO 527MPa (kpsi)10500 (1520)8000 (1160) Poisson's Ratio 0.39 Flexural Modulus ISO 178MPa (kpsi)9300 (1350)6205 (900) Flexural StrengthISO 178MPa (kpsi)290 (42)200 (29) Notched Charpy Impact Strength ISO 179/1eAkJ/m2-40°C (-40°F)1010 -30°C (-22°F)1010 23°C (73°F)1317 Unnotched Charpy Impact Strength ISO 179/1eUkJ/m2-30°C (-22°F)7075 23°C (73°F)85100Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc.ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm. Test temperatures are 23°C unless otherwise stated.The DuPont Oval Logo, DuPont™, The miracles of science™ and Zytel® are trademarks or registered trademarks of DuPont Company. Copyright© 2005.050320/050321The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated; these data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise. The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations in actual end-use conditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in this publication is to be considered as alicense to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent counsel for a freedom to practice opinion on the intended application or end-use of our products. Caution: Do not use this product in medical applications involving permanent implantation in the human body. For other medical applications see "DuPont Medical Caution Statement", H-50102.Zytel ® 70G33L NC010 is a 33% glass fiber reinforced polyamide 66 resin for injection molding.PropertyTest Method UnitsZytel® 70G33L NC010ValueProperty Test Method UnitsDAM50%RH ThermalDeflection Temperature ISO 75f °C (°F)0.45MPa261 (502)1.80MPa252 (486)Melting Temperature ISO 11357-1/-3 °C (°F)10°C/min262 (504)CLTE, Normal ISO 11359-1/-2E-4/C (E-4/F)-40 - 23°C (-40 - 73°F)0.65 (0.36)23 - 55°C (73 - 130°F)0.83 (0.46)55 - 160°C (130 - 320°F) 1.37 (0.76)CLTE, Parallel ISO 11359-1/-2E-4/C (E-4/F)-40 - 23°C (-40 - 73°F)0.24 (0.13)23 - 55°C (73 - 130°F)0.18 (0.10)55 - 160°C (130 - 320°F)0.13 (0.07)ElectricalRelative Permittivity IEC 602501E2 Hz 4.21E6 Hz 4.0Volume Resistivity IEC 60093ohm m1E13Dissipation Factor IEC 60250E-41E2 Hz1001E6 Hz150CTI UL 746A V3.0mm600Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc.ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm.Test temperatures are 23°C unless otherwise stated.The DuPont Oval Logo, DuPont™, The miracles of science™ and Zytel® are trademarks or registered trademarks of DuPont Company. Copyright© 2005.050320/050321 The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated;these data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise.The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations in actual end-useconditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in this publication is to be considered as alicense to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent counsel for a freedom to practice opinion on the intended application or end-use of our products. Caution: Do not use this product in medical applications involving permanent implantation in the human body.For other medical applications see "DuPont Medical Caution Statement", H-50102.Zytel® 70G33L NC010ValueProperty Test Method UnitsDAM50%RH FlammabilityFlammability Classification UL940.71mm HBOxygen Index ISO 4589-1/-2%24High Amperage Arc Ignition Resistance UL 746A arcs0.75mm>200High Voltage Arc Tracking Rate UL 746A mm/min (in/min)32.2 (1.27)Hot Wire Ignition UL 746A s0.71mm81.5mm63.0mm9Temperature IndexRTI, Electrical UL 746B°C0.71mm130RTI, Impact UL 746B°C0.71mm120RTI, Strength UL 746B°C0.71mm130OtherDensity ISO 1183kg/m3 (g/cm3)1390 (1.39)Water Absorption ISO 62, Similar to%Equilibrium 50%RH 1.8Immersion 24h, 2.0mm 1.2Saturation, immersed 5.7Molding Shrinkage ISO 294-4%Normal, 2.0mm 1.1Parallel, 2.0mm0.3Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc.ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm.Test temperatures are 23°C unless otherwise stated.The DuPont Oval Logo, DuPont™, The miracles of science™ and Zytel® are trademarks or registered trademarks of DuPont Company. Copyright© 2005.050320/050321 The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated;these data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise.The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations in actual end-useconditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in this publication is to be considered as alicense to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent counsel for a freedom to practice opinion on the intended application or end-use of our products. Caution: Do not use this product in medical applications involving permanent implantation in the human body.For other medical applications see "DuPont Medical Caution Statement", H-50102.Zytel® 70G33L NC010ValueProperty Test Method UnitsDAM50%RH OtherMold Shrinkage%Flow, 1.6mm (0.063in)0.2Flow, 3.2mm (0.126in)0.3Flow, 6.4mm (0.25in)0.5Transverse, 1.6mm (0.063in) 1.0Transverse, 3.2mm (0.126in) 1.0Transverse, 6.4mm (0.25in) 1.1ProcessingMelt Temperature Range °C (°F)285-305 (545-580)Melt Temperature Optimum °C (°F)295 (565)Mold Temperature Range °C (°F)70-120 (160-250)Mold Temperature Optimum °C (°F)100 (210)Drying Time, Dehumidified Dryer h2-4Drying Temperature °C (°F)80 (175)Processing Moisture Content%<0.20Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc.ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm.Test temperatures are 23°C unless otherwise stated.The DuPont Oval Logo, DuPont™, The miracles of science™ and Zytel® are trademarks or registered trademarks of DuPont Company. Copyright© 2005.050320/050321 The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated;these data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise.The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations in actual end-useconditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in this publication is to be considered as alicense to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent counsel for a freedom to practice opinion on the intended application or end-use of our products. Caution: Do not use this product in medical applications involving permanent implantation in the human body.For other medical applications see "DuPont Medical Caution Statement", H-50102.。

Zytel 101L PA66杜邦纯树脂物性表重要参数由向阳塑胶有限公司提供t e L 1 5 91 7 7 2 0 8 0 1 物理性质公英语比重 1.14 g/cc 1.14克/立方厘米1.14 g/cc 1.14克/立方厘米密度 1.14 g/cc 1.14克/立方厘米0.0412 lb/in³0.0412磅/³吸水率 1.20 % 1.20％@Temperature 23.0 °C@温度23.0°C1.20 % 1.20％@Temperature 73.4 °F@温度73.4°F8.50 %8.50％@Temperature 23.0 °C@温度23.0°C8.50 %8.50％@Temperature 73.4 °F@温度73.4°F8.50 %8.50％@Temperature 23.0 °C@温度23.0°C8.50 %8.50％@Temperature 73.4 °F@温度73.4°F平衡吸湿量 2.60 % 2.60％@Temperature 23.0 °C@温度23.0°C2.60 % 2.60％@Temperature 73.4 °F@温度73.4°F线性成型收缩率0.0140 cm/cm0.0140厘米/厘米@Thickness 2.00 mm厚度2.00毫米0.0140 in/in0.0140 /@Thickness 0.0787 in@厚度0.0787 0.0140 cm/cm0.0140厘米/厘米@Thickness 2.00 mm厚度2.00毫米0.0140 in/in0.0140 /@Thickness 0.0787 in@厚度0.0787线性成型收缩率，流动0.0150 cm/cm0.0150厘米/厘米@Thickness 3.20 mm@厚度3.20毫米0.0150 in/in0.0150 /@Thickness 0.126 in@厚度0.126力学性能公英语Hardness,Rockwell M硬度计，洛氏M59.059.059.059.059.059.059.059.079.079.079.079.079.079.079.079.0硬度计，洛氏ŕ108108108108108108108108121121121121121121121121拉伸强度38.0 MPa38.0兆帕5510 psi5510 PSI@Temperature 121 °C@温度121°C @Temperature 250 °F@温度250°F下41.0 MPa41.0兆帕@Temperature 77.0 °C@温度77.0°C5950 psi5950 PSI @Temperature 171 °F@温度171°F43.0 MPa43.0兆帕@Temperature 121 °C@温度121°C6240 psi6240 PSI @Temperature 250 °F@温度250°F下62.0 MPa62.0兆帕@Temperature 77.0 °C@温度77.0°C8990 psi8990 PSI @Temperature 171 °F@温度171°F77.0 MPa77.0兆帕@Temperature 23.0 °C@温度23.0°C11200 psi11200 PSI @Temperature 73.4 °F@温度73.4°F83.0 MPa83.0兆帕@Temperature 23.0 °C@温度23.0°C12000 psi12000 PSI @Temperature 73.4 °F@温度73.4°F110 MPa110兆帕@Temperature -40.0 °C@温度-40.0°C16000 psi16000 PSI @Temperature -40.0 °F@温度-40.0°F114 MPa114兆帕@Temperature -40.0 °C@温度-40.0°C16500 psi16500 PSI @Temperature -40.0 °F@温度-40.0°F张应力10.390 MPa10.390兆帕@Strain 0.390 %,@应变0.390％，Temperature 40.0 °C温度40.0°C 1506.9 psi1506.9 PSI @Strain 0.390 %,@应变0.390％，Temperature 104 °F温度104°F。

PA66物性数据PA66物性数据是指聚酰胺66（Polyamide 66）的物理性质和化学性质的数据。

聚酰胺66是一种常见的工程塑料，具有优异的力学性能、耐热性、耐化学腐蚀性和电绝缘性能，被广泛应用于汽车、电子、纺织品、电器等领域。

以下是PA66的一些常见物性数据：1. 密度：PA66的密度普通在1.13-1.15 g/cm³之间，具体数值会根据添加剂和加工工艺的不同而有所变化。

2. 熔点：PA66的熔点约为255-265℃，可以通过热差示扫描量热仪（DSC）等测试方法进行测定。

3. 玻璃化转变温度：PA66的玻璃化转变温度通常在40-50℃之间，该温度以下，聚合物呈玻璃态，以上则呈弹性态。

4. 拉伸强度：PA66具有较高的拉伸强度，通常在60-80 MPa之间，该数值可以通过拉伸试验获得。

5. 弯曲强度：PA66的弯曲强度普通在80-100 MPa之间，该数值可以通过弯曲试验获得。

6. 弯曲模量：PA66的弯曲模量约为2000-3000 MPa，该数值可以用来衡量材料的刚度和变形能力。

7. 冲击强度：PA66具有较高的冲击强度，通常在10-20 kJ/m²之间，该数值可以通过冲击试验获得。

8. 热膨胀系数：PA66的热膨胀系数普通在70-90×10^-6/℃之间，该数值可以用来评估材料在温度变化时的尺寸稳定性。

9. 热导率：PA66的热导率约为0.2-0.3 W/(m·K)，该数值可以用来描述材料传导热量的能力。

10. 水吸湿性：PA66具有一定的水吸湿性，通常在1-3%之间，该数值可以通过浸泡试验获得。

11. 耐化学腐蚀性：PA66对许多化学物质具有良好的耐腐蚀性，但对强酸、强碱和氧化剂等具有腐蚀性的物质可能会受到影响。

以上是PA66物性数据的一些常见指标，这些数据可以匡助工程师和设计师选择合适的材料，并进行产品设计和工艺优化。

需要注意的是，不同厂家生产的PA66可能会有稍微的差异，因此在具体应用中还需要参考厂家提供的技术数据和实际测试结果。

PA66物性数据一、引言PA66是一种聚酰胺类高分子材料，具有良好的机械性能、耐热性、耐化学性和电绝缘性能等特点。

本文将详细介绍PA66的物性数据，包括密度、熔点、热膨胀系数、拉伸强度、弯曲强度、冲击强度、热变形温度等。

二、物性数据1. 密度：PA66的密度通常在1.13-1.15g/cm³之间。

2. 熔点：PA66的熔点约为250-260℃。

3. 热膨胀系数：PA66的热膨胀系数为(5-30)×10^-5/℃。

4. 拉伸强度：PA66的拉伸强度在60-80MPa之间，具体数值取决于材料的配方和加工工艺。

5. 弯曲强度：PA66的弯曲强度通常在80-100MPa之间。

6. 冲击强度：PA66的冲击强度约为5-15kJ/m²。

7. 热变形温度：PA66的热变形温度在180-220℃之间。

三、应用领域PA66由于其优异的性能，在工业领域有广泛的应用，主要包括以下几个方面：1. 汽车工业：PA66可以用于制造汽车零部件，如发动机罩、进气歧管、油箱等，其耐热性和机械性能能够满足汽车工业的要求。

2. 电子电器：PA66可以用于制造电子电器产品的外壳和插座等部件，其电绝缘性能和耐化学性能使其成为理想的材料选择。

3. 工程塑料：PA66可以用于制造工程塑料制品，如管道、阀门、储罐等，其耐腐蚀性和机械强度使其成为工程领域的重要材料。

4. 纺织品：PA66可以用于制造纺织品，如尼龙织物、尼龙丝袜等，其优异的耐磨性和耐拉伸性能使其成为纺织品行业的首选材料。

四、结论PA66是一种优秀的高分子材料，具有良好的机械性能、耐热性、耐化学性和电绝缘性能等特点。

本文详细介绍了PA66的物性数据，包括密度、熔点、热膨胀系数、拉伸强度、弯曲强度、冲击强度、热变形温度等。

根据这些物性数据，可以更好地了解和应用PA66材料。

在汽车工业、电子电器、工程塑料和纺织品等领域，PA66都有广泛的应用前景。

PA66物性数据
PA66是一种常用的工程塑料，具有优良的物性数据，本文将对PA66的物性数据进行详细介绍。

一、密度
1.1 PA66的密度一般在1.12-1.14g/cm³之间。

1.2 密度较大，具有较高的质量。

1.3 密度对于材料的加工和应用具有重要影响。

二、力学性能
2.1 PA66具有较高的拉伸强度，一般在60-80MPa之间。

2.2 具有较好的抗拉伸性能，能够承受较大的拉伸应力。

2.3 具有较高的弯曲强度和冲击强度，适用于各种机械零部件。

三、热性能
3.1 PA66具有较高的热变形温度，一般在220-260℃之间。

3.2 具有良好的耐热性，能够在较高温度下保持稳定性能。

3.3 具有较好的耐热老化性能，适用于高温环境下的应用。

四、电性能
4.1 PA66具有较好的绝缘性能，能够阻止电流的传导。

4.2 具有较高的电介质强度和击穿电压，适用于电气领域。

4.3 具有较好的抗电弧性能，能够在高电压下稳定工作。

五、耐化学性
5.1 PA66具有较好的耐化学性，能够抵抗一些化学药品的侵蚀。

5.2 具有较好的耐腐蚀性能，适用于一些恶劣环境下的应用。

5.3 具有较好的耐溶剂性能，能够在一些有机溶剂中稳定使用。

综上所述，PA66作为一种优良的工程塑料，具有较好的物性数据，适用于各种领域的应用，为工程设计提供了广阔的发展空间。

塑料型号及对应说明介绍1 、美国杜邦PA66塑胶原料通用级PA66PA66 美国杜邦ZYTEL 101L 一般级--有润滑66尼龙,有润滑过,以改进其机器进料和脱模特性。

PA66 美国杜邦ZYTEL 101F 一般级--快速周期无核化的66尼龙,其成形性特佳。

PA66 美国杜邦ZYTEL 103HSL 热稳定及润滑新的、改良的、具热稳定性的66尼龙。

PA66 美国杜邦ZYTEL 105 BK 耐候级有良好的抗候性,适合在户外用。

耐冲击改良之66尼龙PA66 美国杜邦ZYTEL 408L 一般级改良之树脂--具优越之轫性及成型性,有润滑过。

PA66 美国杜邦ZYTEL MT409A 一般用、经济型耐冲击性66尼龙。

PA66 美国杜邦ZYTEL ST 801 一般用超韧级66尼龙。

防火级尼龙PA66 美国杜邦ZYTEL FR-7025 一般级--防火 UL94耐燃规格评等为94V-0。

PA66 美国杜邦ZYTEL FR-50 25%玻璃纤维强化 UL94耐燃规格评等为94V-0。

PA66 美国杜邦GRZ尼龙PA 66 加玻璃纤维高强度70G系列PA66 美国杜邦ZYTEL 70G13HSIL 13% 玻璃纤维补强耐热级材料。

PA66 美国杜邦ZYTEL 70G33L 33% 玻璃纤维补强高刚性, 高机械强度。

PA66 美国杜邦ZYTEL 70G33HSIL 33% 玻璃纤维补强耐热级材料。

PA66 美国杜邦ZYTEL 70G30HSLR 30% 玻璃纤补强表面改良表面改良级,耐热及耐水解材料。

PA66 美国杜邦ZYTEL 15005 BK 33% 玻璃纤维补强耐热及耐水解材料。

PA66 美国杜邦ZYTEL 70G43L 43% 玻璃纤维补强高刚性, 高机械强度。

耐冲击71G系列PA66 美国杜邦ZYTEL71G13L 13% 玻璃纤补强高耐冲性, 高刚性, 高机械强度。

PA66 美国杜邦ZYTEL71G33L 33% 玻璃纤补强高耐冲性, 高刚性, 高机械强度。