工厂常用名词中英文对照

工廠內常用英文簡稱辭彙解釋品質人員名稱類QC quality control 品質管理人員FQC final quality control 終點品質管制人員IPQC in process quality control 制程中的品質管制人員OQC output quality control 最終出貨品質管制人員IQC incoming quality control 進料品質管制人員TQC total quality control 全面質量管理POC passage quality control 段檢人員QA quality assurance 質量保證人員OQA output quality assurance 出貨質量保證人員QE quality engineering 品質工程人員SQE supplier quality engineer 供應商品質工程師品質保證類FAI first article inspection 新品首件檢查FAA first article assurance 首件確認TVR tool verification report 模具確認報告3B 3B (3 tooling booking items) 模具正式投產前確認(壓力、溫度/油,水、料)CP capability index 能力指數CPK capability index of process 模具製程能力參數SSQA standardized supplier quality 合格供應商品質評估OOBA out of box audit 開箱檢查QFD quality function deployment 品質機能展開FMEA failure model effectiveness analysis 失效模式分析8D 8 disciplines 8項回覆內容FA final audit 最後一次稽核CAR corrective action request 改正行動要求corrective action report 改正行動報告PDCA Plan, Do, Check, ActFTA Factor tree analysis 因素樹分析IS Initial Sample 首批樣品OTS Off tool samples 初期樣品PS Prototype sample 手工樣品FQC運作類AQL Acceptable Quality Level 運作類允收品質水準S/S Sample size 抽樣檢驗樣本大小AC Accept 允收RE Reject 拒收CS Critical specification 重要特性MAJ Major 主要的MIN Minor 輕微的AOQ Average Output Quality 平均出廠品質AOQL Average Output Quality Level 平均出廠品質Q/R/S Quality/Reliability/Service 品質/可靠度服務MIL-STD Military-Standard 軍用標準S I-S IV Special I-Special IV 特殊抽樣水準等級P/N Part Number 料號L/N Lot Number 批號B/N Bacht Number 批號AWD Accept with Deviation 特采UAI Use As It 首件檢查報告FPIR First Piece Inspection Report 百萬分之一PPM Percent Per Million 批號制程統計品管專類SPC Statistical Process Control 統計製程管制SQC Statistical Quality Control 統計品質管制R Range 全距AR Average Range 全距平均值UCL Upper Central Limit 管制上限LCL Lower Central Limit 管制下限MAX Maximum 最大值MIN Minimum 最小值GRR Gauge Reproducibility & Repeatability 量具之再制性及重測性判斷量可靠與否DIM Dimension 尺寸DIA Diameter 直徑FREQ Frequency 頻率N Number 樣品數其他品質術語類QCC Quality Control Circle 品質圈QIT Quality Improvement Team 品質改善小組PDCA Plan Do Check Action 計劃執行檢查總結ZD Zero Defect 零缺點QI Quality Improvement 品質改善QP Quality Policy 目標方針TQM Total Quality Management 全面品質管理MRB Material Reject Bill 退貨單LQL Limiting Quality Level 最低品質水準RMA Return Material Audit 退料認可QAN Quality Ameliorate Notice 品質改善活動ADM Absolute Dimension Measurement 全尺寸測量QT Quality Target 品質目標7QCTools 7 Quality Controll Tools 品管七大手法通用之件類ECN Engineering Change Notes 工程變更通知(供應商) ECO Engineering Change Order 工程改動要求(客戶) PCN Process Change Notice 工序改動通知PMP Product Management Plan 生產管制計劃SIP Specification In Process 製程檢驗規格SOP Standard Operation Procedure 製造作業規範IS Inspection Specification 成品檢驗規範ABOM Bill Of Material 物料清單PS Package Specification 包裝規範SPEC Specification 規格DWG Drawing 圖面部類PMC Production & Material Control 生產和物料控制PPC Production Plan Control 生產計劃控制MC Material Control 物料控制ME Manufacture Engineering 製造工程部PE Project Engineering 產品工程部A/C Accountant Dept 會計部P/A Personal & Administration 人事行政部DC Document Center 資料中心QE Quality Engineering 品質工程(部)QA Quality Assurance 品質保證(處)QC Quality Control 品質管制(課)PD Product Department 生產部LAB Laboratory 實驗室IE Industrial Engineering 工業工程R&D Research & Design 設計開發部P Painting 烤漆(廠)A Assembly 組裝(廠)S Stamping 沖壓(廠)生產類PCS Pieces 個(根,塊等)PRS Pairs 雙(對等)CTN Carton 卡通箱PAL Pallet/skid 棧板PO Purchasing Order 采購訂單MO Manufacture Order 生產單D/C Date Code 生產日期碼ID/C Identification Code (供應商)識別碼SWR Special Work Request 特殊工作需求L/N Lot Number 批號P/N Part Number 料號其他OEM Original Equipment Manufacture 原設備製造PCE Personal Computer Enclosure 個人電腦外設PC Personal Computer 個人電腦CPU Central Processing Unit 中央處理器SECC SECC` 電解片SGCC SGCC 熱浸鍍鋅材料U.S.A the United States of America 美國A.S.A.P As Soon As Possible 盡可能快的E-MAIL Electrical-Mail 電子郵件N/A Not Applicable 不適用QTY Quantity 數量vs. versus 以及.REV Revision 版本JIT Just In Time 零庫存I/O Input/Output 輸入/輸出OK OK 好NG Not Good 不行,不合格C=0 Critical=0 極嚴重不允許ESD Electro Static Discharge 靜電排放5S 希臘語整理,整頓,清掃,清潔,教養ATIN Attention 知會CC Carbon Copy 副本復印相關人員APP Approve 核準,認可,承認CHK Check 確認AM Ante Meridian 上午PM Post Meridian 下午CD Compact Disk 光碟CD-ROM Compact Disk Read-Only Memory 只讀光碟FDD Floppy Disk Drive 軟碟機HDD Hard Disk Drive 碟碟機REF Reference 僅供參考CONN Connector 連接器CAV Cavity 模穴CAD Computer Aid Design 計算機輔助設計ASS''''Y Assembly 裝配,組裝MAT''''S Material 材料IC Integrated Circuit 集成電路T/P True Position 真位度TYP Type 類型WDR Weekly Delivery Requirement 周出貨需求C?T Cycle Time 制程週期L/T Lead Time 前置時間(生產前準備時間)S/T Standard Time 標準時間P/M Product Market 產品市場3C Computer, Communication, Consumer electronics’ 消費性電子5W2H When, Where, Who, What, Why, How,How many5M Man, Machine, Material, Method, Measurement4M1E Man, Machine, Material, Method, Environment4MIH Man, Material, Money, Method, Time 人力,物力,財務,技術,時間(資源)SQA Strategy Quality Assurance 策略品質保證DQA Design Quality Assurance 設計品質保證MQA Manufacture Quality Assurance 製造品質保證SSQA Sales and service Quality Assurance 銷售及服務品質保證LRR Lot Reject Rate 批退率BS Brain storming 腦力激蕩EMI Electronic Magnetron Inspect 高磁測試FMI Frequency Modulator Inspect 高頻測試B/M Board/Molding (flat cable)SPS Switching power supply 電源箱DT Desk Top 臥式(機箱)MT Mini-Tower 立式(機箱)LCD Liquid Crystal Display 液晶顯示器CAD Computer AID Design 電腦輔助設計CAM Computer AID Manufacturing 電腦輔助製造CAE Computer AID Engineering 電腦輔助工程BIOS Advanced Basic in put/output system 先進的基本輸入/輸出系統CMOS Complementary Metal Oxide Semiconductor 互補金屬氧化物半導體PDA Personal Digital Assistant 個人數位助理IC Integrated Circuit 集成電路ISA Industry Standard Architecture 工業標準體制結構MCA Micro Channel Architecture 微通道結構EISA Extended Industry Standard Architecture 擴充的工業標準結構SIMM Single in-line memory module 單項導通匯流組件DIMM Dual in-line Memory Module 雙項導通匯流組件LED Light-Emitting Diode 發光二級管FMEA Failure Mode Effectiveness 失效模式分析W/H Wire Harness 金屬線緒束集組件F/C Flat Cable 排線PCB Printed Circuit Board 印刷電路板CAR Correction Action Report 改善報告NG Not Good 不良WPR Weekly Delivery Requirement 周出貨要求PPM Parts Per Million 百萬分之一TPM Total Production Maintenance 全面生產保養MRP Material Requirement Planning 物料需計劃OC Operation System 作業系統TBA To Be Design 待定,定缺D/C Drawing Change 圖紙變更/設計變更EMI Electrical-Music Industry 電子音樂工業RFI Read Frequency Input 讀頻輸入。

工厂全名中英文对照Chemical Factory 化工厂Petrochemical Plant 石油化工厂Oil Chemical Factory 油脂化工厂Chemical Fertilizer Plant 化肥厂Potassium Fertilizer Plant 碳肥厂Chemical Fibre Plant 化学纤维厂Synthetic Fibre Plant 合成纤维厂Soap Factory 肥皂厂Chemical Factory of Daily Use 日用化工厂Toothpaste Factory 牙膏厂cosmetic Factory 化妆品厂Perfumery Plant 香料厂Beauty Products Factory 美容品厂Paint Factory 油漆厂Cement Plant 水泥厂Building Materials Factory 建材厂Timber Mill 木材厂Furniture Factory 家具厂Bricks and Tiles Plant 砖瓦厂Lime Factory 石灰厂Power Plant 发电厂Water Works 自来水厂Electroplate Factory 电镀厂Elevator Factory 电梯厂Iron Works 钢铁厂Stainless Steel Plant 不锈钢厂Alloy Steel Plant 合金钢厂Metallurgical Refinery 冶炼厂Copper Material Factory 铜材厂Aluminum Material Factory 铅材厂Non-ferrous Metals Processing Factory 有色金属加工厂Casting Factory 铸造厂Boiler Factory 锅炉厂Metallurgical Factory 冶金厂Machines Plant 机器厂Heavy Machines Plant 重型机器厂Machine Tools Plant 机床厂Diesel Engines Factory 柴油机厂Compressors Factory 压缩机厂Electrical Machinery Factory 电机厂Coolers Factory 冷冻机厂Machinery Plant 机构制造厂Shipping Machinery Plant 船舶机械厂General Machinery Plant 通用机械厂Crane Factory 起重机厂Tractor Factory 拖拉机厂Farm Tools Plant 农具厂Machinery Plant of Light Industry 轻工机械厂Commercial Machinery Plant 商业机械厂Building Machinery Plant 建筑机械厂Engineering Machinery Plant 工程机械厂Washing Machinery Plant 洗涤机械厂Mining Machinery Plant 矿山机械厂Heavy Machinery Plant 重型机械厂Shipyard 造船厂Automobile Factory 汽车制造厂Passenger Automobile Factory 客车制造厂Automobile Repair Plant 汽车修理厂Automobile Service Factory 汽车修理厂Bicycle Plant 自行车厂Sewing Machine Factory 缝纫机厂Clock Factory 钟厂Watch Factory 表厂Electronic Watch Plant 电子表厂Textile Mill 纺织厂Cotton Mill 棉纺织厂Woolen Mill 毛纺厂Silk Mill 丝厂Embroidery Factory 刺绣厂Clothing Factory 服装厂Woolen Sweater Mill 羊毛衫厂Towel Factory 毛巾厂Mosquito Net Factory 蚊帐厂Sheet Factory 床单厂Bedclothes Factory 床上用品厂Shoes Factory 鞋厂Leather Shoes Factory 皮鞋厂Rubber Shoes Factory 胶鞋厂Plastic Shoes Factory 塑料鞋厂Boots Factory 制靴厂Socks Factory 袜厂Leather Factory 皮革厂Oil Refinery 食油厂Flour Mill 面粉厂Rice Products Mill 米制品厂Flour Products Mill 面制品厂Foodstuffs Factory 食品厂Bakery 面包厂Milk Products Plant 乳制品厂Canned Foodstuffs Factory 罐头厂Beverage Factory 饮料厂Alcohol Plant 酒精厂Beer Brewery 啤酒厂Winery 酿酒厂Sugar Refinery 制糖厂Confectionery 糖果厂Biscuits Factory 干厂Spice Factory 调味品厂Gourmet Powder Factory 味精厂Cigarettes Factory 卷烟厂Matches Factory 火柴厂Bean Products Factory 豆制品厂Pastries Factory 糕点厂Tea Processing Factory 茶厂Pharmaceutical Factory 制药厂Medical Apparatus Factory 医疗器械厂Medical Equipment Plant 医疗设备厂Sanitary Materials Factory 卫生材料厂Insecticide Factory 农药厂Veterinary Medicines Factory 兽药厂Chemical Pharmaceutical Factory 化学制药厂Valve Plant 阀门厂Bearing Factory 轴承厂Gear Factory 齿轮厂Standard Component Factory 标准件厂Tools Factory 工具厂Hardware Tools Factory 五金工具厂Gas Appliance Factory 煤气用具厂Kitchen Utensils Factory 厨具厂Hardware Factory 五金厂Hardware and Electric Appliance Factory 五金电器厂Metal Processing Factory 金属加工厂Metal Component Factory 金属构件厂Lighter Factory 打火机厂Nail Factory 制钉厂Drawing Pin Factory 图钉厂Zipper Factory 拉链厂Lock Factory 锁厂Battery Plant 电池厂Fashlight Plant 电筒厂Electric Bulbs Factory 电灯泡厂Glass Factory 玻璃厂Plastics Plant 塑料厂Rubber Plant 橡胶厂Navigation Apparatus Factory 航海仪器厂Optical Instrument Factory 光学仪器厂Electronic Instruments Plant 电子仪器厂Educational Instrument Factory 教学仪器厂Printing House 印刷厂Toy Factory 玩具厂Paper Mill 造纸厂Musical Instrument Factory 乐器厂Piano Factory 钢琴厂Stationery Factory 文具厂Ink Factory 墨水厂Fountain Pen Factory 金笔厂Pencil Factory 铅笔厂Camera Factory 照相机厂Ceramics Factory 陶瓷厂Literature and Art Development Company 文艺进展公司Cultural Expansion Company 文化开拓公司Cultural Service Firm 文化服务公司Performing Company 演出公司Film Company 电影公司Film Service Firm 电影服务公司Broadcasting and Television Industry Company 广播电视工业公司Acoustics Engineering Company 音响工程公司Record Company 唱片公司Photography Industry Company 照相工业公司Exhibition Agency 展览公司Advertising Agency 广告公司Arts and Crafts Industry Company 工艺美术工业公司Art Design Firm 美术设计公司Art Decoration Firm 美术装潢公司Packaging Decoration Firm 包装装潢公司Building Engineering Company 建筑工程公司Building Foundation Company 建筑基础公司Civil Engineering Company 土木工程公司Garden Construction Engineering Company 园林建筑工程公司Building Material Company 建筑材料公司Building Material Supply Company 建筑材料供应公司Building Material Trading Company 建材贸易公司Building Material Service Company 建筑材料服务公司New Building Material Company 新型建筑材料公司Real Estate Development Company 房地产开发公司Real Estate Agency 房产代理公司Industrial Equipment Installing Company 工业设备安装公司Installing Company of Chemical Industry 化工安装公司Electrical Installing Company 机电安装公司Building Decoration Company 建筑装修〔装饰〕公司Building Decoration Engineering Company 建筑装修〔装饰〕工程公司Commercial Company 商业公司Collective Commercial Company 集体商业公司Overseas Chinese Commodities Supply Company 华侨商品供应公司Daily-use Sundry Goods Company 日用杂品公司Foodstuffs Company 食品公司Materials Company 物资公司Beverage Industry Company 饮料工业公司Frozen Foodstuffs Company 冷冻食品公司Native Produce & Animal By-products Import and Export Corporation 土产畜产进出口公司Chemicals Import and Export Corporation 化工进出口公司Metals & Minerals Import and Export Corporation 五金矿产进出口公司Electronics Import and Export Corporation 电子技术进出口公司Electric Wire & Cable Export Corporation 电线电缆出口联营公司Publishing Industry Trading Corporation 出版对外贸易公司Packaging Import and Export Corporation 包装进出口公司Instruments Import and Export Corporation 仪器进出口公司Historical Relics Exhibition Corporation for Foreign Countries 对外文物展览公司Performing Arts Agency 对外演出公司Overseas Building Materials and Equipment Corporation 对外建筑材料设备公司Foreign Trade Storage Corporation 对外贸易仓储公司Foreign Trade Transportation Corporation 对外贸易运输公司Foreign Trade Consultation & Technical Service Corporation 对外贸易咨询与技术服务公司Exhibition Agency for Foreign Countries 对外展览公司Export Commodities Fair 出口商品交易会Machinery & Equipment Import and Export Corporation 机械设备进出口公司Complete Plant import and Export Corporation 成套设备进出口公司Communications Import and Export Service Corporation 交通进出口服务公司Machine-building International Corporation 机械对外经济技术合作公司Machinery Import and Export Corporation 机械进出口公司Corporation for International Cooperation in Agriculture, Livestock and Fishery 农牧渔业国际合作公司Import and Export Service Company for Farms and Land Reclamation 农垦进出口服务公司Import and Export Commodities Inspection Corporation 进出口商品检验公司Technical Import and Export Corporation 技术进出口公司Textiles Import and Export Corporation 纺织品进出口公司Import Corporation of Textile Machinery 纺织机械进出口公司Import Corporation of Technology of Textile Machinery 纺织机械技术进出口公司Metallurgical Import and Export Corporation 冶金进出口公司Forestry Import and Export Company 林业进出口公司Forestry Machinery Import and Export Company 林业机械进出口公司International Packaging Leasing Corporation Ltd. 国际包装租赁International Non-ferrous Metals Leasing Corporation Ltd. 国际有色金属租赁International Book Trading Corporation 国际图书贸易International Economic Consultants Incorporation 国际经济咨询公司International Marine Containers Ltd. 国际海运集装股份Light Industrial Products Import and Export Corporation 轻工业品进出口公司Publication Import and Export Corporation 图书进出口公司Tea and Native Produce Import and Export Corporation 茶叶土产进出口公司Animal Breeding Stock Import and Export Corporation 种畜进出口公司Bearing Joint Export Corporation 轴承出口联营公司Aero-technology Import and Export Corporation 航空技术进出口公司Tobacco Import and Export Corporation 烟草进出口公司Leasing Company Ltd. 租赁Railway Foreign Service Corporation 铁路对外服务公司Cereals, Oil and Foodstuffs Import and Export Corporation 粮油食品进出口公司Coal Import and Export Corporation 煤炭进出口公司Microforms Import and Export Corporation 缩型出版物进出口公司Precision Machinery Import and Export corporation 周密机械进出口公司Abrasives Export Corporation 磨料磨具进出口公司Scientific Instrument import and Export Corporation 科学仪器进出口公司Foreign Trade Corporation 对外贸易公司Aquatic Products Import and Export Corporation 水产进出口公司Ceramics Import and Export Corporation 陶瓷进出口公司International Cooperation Corporation of Economics and Technology 国际经济技术进出口公司Trading Company 贸易公司Comprehensive Trading Company 综合贸易公司Trade Development Company 贸易进展公司Overseas Economic Trading Company 海外经济贸易公司Investment Company 投资公司Trust Company 信托公司International Trust and Investment Company 国际信托投资公司Loan Investment Company 信贷投资公司Overseas Chinese Investment Company 华侨投资公司People's Insurance Agency 人民保险公司Labour Insurance Agency 劳动保险公司Life Insurance Agency 人寿保险公司Pacific Insurance Agency 太平洋保险公司Securities Agency 证券公司Stock Exchange 股票交易所Futures Exchange 期货交易所Commodities Futures Exchange 商品期货交易所Futures Brokerage Company Ltd. 期货经纪Cereals and Oil Futures Exchange 粮油期货交易所Posts and Telecommunications Apparatus Company 邮电器材公司Posts and Telecommunications Engineering Company 邮电工程公司Running-water Company 自来水公司Water and Electricity Construction Company 水电建设公司Power Industry Company 电力工业公司Electrical Installing Company 电力安装公司Air Line 航空公司Shipping Company 船舶公司Ocean Transportation Company 远洋运输公司Salvage Company 打捞公司Ocean Shipping Agency 外轮代理公司Ocean Shipping Tally Company 外轮理货公司Ship-building Company 造船公司Automobile Transportation Company 汽车运输公司Container Transportation Company 集装箱运输公司Storage and Transportation Company 储运公司Taxi Company 出租汽车公司Automobile Service Company 汽车修理公司Ocean Shipping Supply Company 外轮供应公司Fishing-boat Industry Company 渔船工业公司Automobile Parts Company 汽车配件公司Automation Engineering Company 自动化工程公司Microcomputer Company 微电脑公司Computer Company 运算机公司Computer Software Development Company 运算机软件开发公司Hardware Company 五金公司Household Electric Appliance Company 家用电器公司Refrigerator Industry Company 电冰箱工业公司Radio Apparatus Company 无线电器材公司Performing Instrument Company 演出器材公司Printing Apparatus Company 印刷器材公司Teaching Instrument Company 教学仪器公司。

工厂生产常用英文术语缩写工厂生产常用英文术语缩写5S : 5S管理ABC : 作业制成本制度 (Activity-Based Costing)ABB : 实施作业制预算制度 (Activity-Based Budgeting)ABM : 作业制成本管理 (Activity-Base Management)APS : 先进规画与排程系统(Advanced Planning and Scheduling)ASP : 应用程序服务供货商（Application Service Provider）ATP : 可承诺量 (Available To Promise)AVL : 认可的供货商清单(Approved Vendor List)BOM : 物料清单 (Bill Of Material)BPR : 企业流程再造 (Business Process Reengineering)BSC : 平衡记分卡 (Balanced ScoreCard)BTF : 计划生产 (Build To Forecast)BTO : 订单生产 (Build To Order)CPM : 要径法 (Critical Path Method)CPM : 每一百万个使用者会有几次抱怨(Complaint per Million) CRM : 客户关系管理 (Customer Relationship Management)CRP : 产能需求规划 (Capacity Requirements Planning)CTO : 客制化生产 (Configuration To Order)DBR : 限制驱导式排程法 (Drum-Buffer-Rope)DMT : 成熟度验证(Design Maturing T esting)DVT : 设计验证(Design Verification Testing)DRP : 运销资源计划 (Distribution Resource Planning)DSS : 决策支持系统 (Decision Support System)EC : 设计变更／工程变更 (Engineer Change)EC : 电子商务 (Electronic Commerce)ECRN : 原件规格更改通知(Engineer Change Request Notice) EDI : 电子数据交换 (Electronic Data Interchange)EIS : 主管决策系统 (Executive Information System)EMC : 电磁相容(Electric Magnetic Capability)EOQ : 基本经济订购量 (Economic Order Quantity)ERP : 企业资源规划 (Enterprise Resource Planning)FAE : 应用工程师(Field Application Engineer)FCST : 预估(Forecast)FMS : 弹性制造系统 (Flexible Manufacture System)FQC : 成品质量管理 (Finish or Final Quality Control)IPQC: 制程质量管理 (In-Process Quality Control)IQC : 进料质量管理 (Incoming Quality Control)ISO : 国际标准组织(International Organization for Standardization)ISAR: 首批样品认可(Initial Sample Approval Request)JIT : 实时管理 (Just In Time)KM ：知识管理 (Knowledge Management)L4L : 逐批订购法 (Lot-for-Lot)LTC : 最小总成本法 (Least Total Cost)LUC : 最小单位成本 (Least Unit Cost)MES : 制造执行系统 (Manufacturing Execution System)MO : 制令(Manufacture Order)MPS : 主生产排程 (Master Production Schedule)MRO : 请修(购)单(Maintenance Repair Operation)MRP : 物料需求规划 (Material Requirement Planning)MRPII : 制造资源计划 (Manufacturing Resource Planning)NFCF : 更改预估量的通知Notice for Changing ForecastOEM : 委托代工 (Original Equipment Manufacture)ODM : 委托设计与制造 (Original Design & Manufacture)OLAP : 在线分析处理 (On-Line Analytical Processing)OLTP : 在线交易处理 (On-Line Transaction Processing)OPT : 最佳生产技术 (Optimized Production Technology) OQC : 出货质量管理 (Out-going Quality Control)PDCA : PDCA管理循环 (Plan-Do-Check-Action)PDM : 产品数据管理系统 (Product Data Management) PERT : 计划评核术 (Program Evaluation and Review Technique) PO : 订单(Purchase Order)POH : 预估在手量 (Product on Hand)PR : 采购申请Purchase RequestQA : 品质保证(Quality Assurance)QC : 质量管理(Quality Control)QCC : 品管圈 (Quality Control Circle)QE : 品质工程(Quality Engineering)RCCP : 粗略产能规划 (Rough Cut Capacity Planning)RMA : 退货验收Returned Material ApprovalROP : 再订购点 (Re-Order Point)SCM : 供应链管理 (Supply Chain Management)SFC : 现场控制 (Shop Floor Control)SIS : 策略信息系统 (Strategic Information System)SO : 订单(Sales Order)SOR : 特殊订单需求(Special Order Request)SPC : 统计制程管制 (Statistic Process Control)TOC : 限制理论 (Theory of Constraints)TPM : 全面生产管理Total Production ManagementTQC : 全面质量管理 (Total Quality Control)TQM : 全面品质管理 (Total Quality Management)WIP : 在制品 (Work In Process)。

工厂专业英语术语Assem bly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Pneumatic screw driver气动起子worktable 工作桌O OBA开箱检查fit together组装在一起fasten锁紧(螺丝) fixture 夹具(治具) pallet栈板barcode条码barcode scanner条码扫描器fuse together熔合fuse m achine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cos metic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs. inch 镑、英寸EMI gasket导电条front plate前板rear plate后板chassis 基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS 电源电压接拉键sheet m etal parts 冲件plastic parts塑胶件SOP制造作业程序material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线left fork叉车personnel resource depart m en t 人力资源部production depart ment生产部门planning depart m ent企划部QC Secti on品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common e quipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic m achine油压机lathe车床planer |'plein?|刨床miller铣床grinder磨床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting m achine铆合机position职务president董事长general manager总经理special assistant m anager特助factory director厂长depart m ent director部长deputy m anager | =vice m anager副理section supervisor课长deputy section supervisor =vice section superisor副课长group leader/supervisor组长line supervisor线长assistant m anager助理to m ove, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect m aterial接料to reverse m aterial 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load m aterial上料to unload m aterial卸料to return m aterial/stock to退料scraped |'skr?pid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient m anufacturing procedure制程不良oxidation |' ksi'dei?n|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良em bedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车com pound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓administration/general affairs dept总务部autom atic screwdriver电动启子thicknes s gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单location地点present m embers出席人员subject主题conclusion结论decision item s决议事项responsible depart m ent负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheet PCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准depart ment部门stock age analysis sheet 库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete m aterial良品已呆滞to be inspected or reworked 待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet 年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw m aterials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list 备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flam e cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die butto n圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopp er清角active plate活动板baffle plate挡块cover plate盖板m ale die公模fem ale die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetizat ion去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜 D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products 报放心品defective products不良品finished products成品disposed products处理品barcode 条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer 备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting m achine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction =interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕?? shine 亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grai n细粒grit m aker抽粒机cushion缓冲magnalium镁铝合金m agnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tem po生产进度现状torque扭矩spline=t he multiple keys花键quenchi ng淬火tem pering回火annealing退火carbonization碳化tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机。

部门名称中英互译人事部办公室：HR（Human Resource ）Office保安室：Safe guarding Room or Guard Room接待室：Reception Room会客室（洽谈室）：Chatting Room会议室：Meeting Room塑胶部办公室：Plastic Dept Office配料室：Ｍixing Room or Mixing Compartment碎料室：Milling Room or Milling Compartment装配部办公室：Assembly Department OfficeA拉： A Line综合办公室：General Office仓库：Warehouse or Storehouse财务室：Financial Room采购部：Purchasing Department工程部：Engineering Department成本部：Cost DepartmentPMC部：PMC Department生产部：Manufacture Department喷油部：Oil Spout Department办公区：Office Area生产区：Manufacturing Area移印室Pad Printing Room品质部: QualityQA实验室：QA Lab工模部：Tooling Department工模部办公室：Tooling Department Office工模部仓库：Tooling Department Warehouse省模室：Polishing Room火花机室：Discharge Machine Room工模室：Tooling RoomCNC室: CNC Room车床室：Lathe Room磨床：Grinder前台：Reception Desk总监室: Director Room总经理室：General Manager Room贵宾餐厅：VIP Eatery卫生间：Rest Room管理食堂：Management Eatery员工食堂：Staff Eatery技工食堂：Artificer Eatery厨房：Kitchen储存室：Storage Room7S是整理(sort)、整顿(Neatness)、清扫(sweep)、清洁(sanitary)、素养(sentiment)、节约(save)、安全(safety)总裁办President Office行政部Administrative Department财务部Financial Department营销部Sales Department营运部Operation Department。

制衣厂常用术语中英文对照表一）部门术语及常用词A.裁床：Cutting room1 纸样制作原理及方法：The methods & principle of pattern making2 排唛架方法：The methods of marker making3 YPD的计算及工厂唛架利用率：YPD calculation & marker use rate4 拉布及割布方法，工票之使用方法及功用：Methods & function of spreading & cutting5 裁剪日产量：Daily quantity of cutting6 裁单：Cutting ReportB．板房：Sample room1 裤子，恤衫的车缝工序：Understand the procedures of sewing pants and shirt2 熟识各个工序的称谓：Understand the name of various procedures3 熟识各个线缝的名称及功能：Understand the name and function in various seams4 了解缝1件衫所需的辅料：understand sub-materials used in a shirt5 熟识样板制造单：Understand sample orderC．车缝车间1 熟识生产制造单：Understand the production order2 熟识整个生产线的工序安排：Understand the product line lay out3 各个工序的定价标准：Price standard of various process4 质量控制方法：Methods of quality control5 日产量：Daily product quantity6 常见的车缝设备：Work-aids sewing Machine & attachments7 常见的车缝疵点：Various types of sewing problemD.洗水厂Washing department1 洗水方法及不同的洗水特点：Washing type & various characteristic2 不同洗水的洗涤剂：Various chemical consumption for each type of garment wash3 如何控制洗水质量：Garment washing quality controlE．包装：Packing department1 包装工序的任务及要求：What propose with packing process2 包装方法：Types of packing：Stand-up packing：企装, Flat packing：扁装Semi stand packing: 铲装/半企装3 包装所需的辅料：What assembly will be used in packing4 包装机械设备：Packing equipment5 装箱方法：Methods of packing6 出货所需之文件：Shipping document7 如何控制包装质量：How to control packing quality二）制衣厂质量检查QC Quality control1．服装中-英名称衬衣Shirt/Blouse T-恤T-Shirt毛衣Sweat shirt 西装Suit裤子Pants 牛仔裤Jeans喇叭裤子Bell bottom jeans 裙子Skirt外套Coat 连帽T-恤Parka运动衫Sports jacket 连衣裙Dress圆台裙Circular 百褶裙Gather Skirt裤裙Flare Culottes Skirt 马甲Vest背心Tank top 燕尾领Wing collar2．衣服部位中-英文名称前幅Front 后幅Back上级领Collar 下级领Collar Band前筒Front Placket 钮子Button stay袋Pocket 担干Yoke袖Sleeve 袖侧Sleeve placket介英Cuff 裤头Waist Band耳仔Belt Loop 拉链贴Zipper catch拉链牌Zipper Fly 袋贴Pocket Facing前浪Front Rise 后浪Back Rise裤脚Leg Bottom 侧骨Side Seam袋口Pocket Mouth 袖叉Sleeve Slit机头Riser 明袋Patch Pocket唇袋Jetted Pocket 袋盖Pocket Flap插袋Cross Pocket 袋衬Bearer袋布Pocket Bag 袖口贴Sleeve Band兜帽Hood 夹圈Armhole钮门Button Hole 凤眼Eyelet Button Hole 捆条圆领Crew neck3．制衣工序名称Garment Product Procedure纸样Pattern 唛架Marker裁剪Cutting 绣花Embroidery样板Sample 车缝Sewing洗水Washing 成衣染Garment Dye整烫Ironing 包装Packing质量检查Quality Inspection 质量控制Quality Control石洗Stone Wash 化学洗Chemical Wash茶化洗Teast Wash 漂洗Bleach Wash钮Button 线Thread唛头/商标Label 挂卡Hang tag贴纸Sticker 朴Interlining胶袋Plastic/Poly bag 胶夹Plastic Clip拉链Zipper 橡根Elastic Band肩垫Shoulder Pad 衬纸Tissue Paper绅Drawstring 领蝴蝶Collar Butterflies领胶条Collar Stripe 纸箱（Paper）Carton（胶）针(Poly) Pins 检针济Sticker纸板Paper board 蝴蝶Butterfly纸/胶领条Paper/Plastic collar band 尺码贴纸Size sticker插竹Collar stay 条形码Jan code/bar code4．车缝工序Sewing process埋夹close side seam 车唛sew label间线子口hem stitch seam上间袖attach sleeve/topstitch sleeve 打枣Tacking 接线Joints三）、布的中-英文名称1.梭织布Woven牛津纺Oxford 府绸Poplin多臂提花Dobby斜纹Twill青年布Chambray 绒布Flannel条格布gingham 泡泡纱Seersucker灯芯绒Corduroy 卡其Drill哔叽Serge 华达呢Gabercord主身布Body fabric撞布Contrast fabric条格Check 斜纹Stripe净色Solid 支数warp count2.针织布Knit平纹布Jersey (Drop 1*1 Jersey/Lycry Jersey)珠地Pique (Twill Pique /Oxford pique /Athletic pique)双珠地Lacoste (Oxford Lacoste 牛津珠地)双面布Interlock (interlock pique /interlock jacquard 双面提花)毛圈布Terry ( twill French terry 法兰绒/Fleece 磨毛毛圈布)提花Jacquard (herringbone /bubble jacquard 泡泡提花布)罗纹Rib (mini waffle 十字罗纹/法式罗纹French rib)棉布Cotton fabric麻布Linen丝绸Silk毛Wool化学纤维Chemical fiber四）制单要求The requirement in production order生产制单production order 样板制造单Sample order款号Style Number 客户Customer数量quantity 尺码Size spec.交货期Delivery 装箱要求Carton Requirement 纸箱规格Carton Measurement 毛重Cross height净重Net height 说明Description目的地Final destination 颜色color五）、其它样板Sample 货前板Pre-Production sample 销售板Sales Sample 展览板Presentation sample 批准板Approval sample 会议板Meeting Sample测试板Test sample 船头办Pre-shipment Sample 六）布疵常见术语紧纱：Tight 断纱：Broken Yarn走纱：Misend / Mispick 抽纱：Yarn with Drawn针孔：Needle Holes 针路：Vertical Line横间：Horizontal Line 漏针：Dropped Stitch停机布痕：Stop Mark 幼纱：Yarn Thinning/Thin Yarn错花：Wrong Pattern or Wrong Structure飞花：Fly yarn 色差Shading染色Color fastness 粗纱Thick yarn色纱Color yarn织错纱Wrong pick end稀密路Filling bar 布纹弯曲不平Bowing皱摺Crease 粗粒Slub起毛Hairy 织入杂物Gout起球Balling-up七）车缝常见术语跳线：Skip Stitch 用错原料：Wrong Material缝线散口：Run off 用错缝线：Incorrect Thread错唛：Wrong Label 破洞：Holes突咀：Excess Extension 不对称：Mismatched车着唛头：Sandwich Label 歪唛：Off Center or Side left/right 尖位不尖：Pointed Area not Sharp 弯位不弯：Unsmooth Curve爆口：Open Seam 披苏：Loose Thread插竹歪：Crooked Collar Stay 领底松：Collar setting too Loose烂钮尖：Burst Collar Point 领尖不对条：Mismatched Collar Stripe 错领型：Wrong Collar Shape 刀剪领：Scissoring露上领线：Thread Visible Outside 下级走样：Poor Banding领咀长短不定：Wrong Lapel Length 领错底面：Overturn Collar起耳子：Lock stitches-loop 断线：Broken Stitches落坑：Run off Stitch 积线球：Lumps of Thread藏色线：Trapped Color Thread 驳线不齐：Untidy Joined Stitching缝线阔窄：Uneven Seam 线路不美：Untidy Stitching皱：Pocking 露牙：Grinning走鸡：Miss Design Feature 大眼皮：Uneven seam高底袋：High/low pocket 筒起波浪：Fullness on Center Placket 筒歪：Crooked Center Placket 担干谷：Fullness on Yoke前肩大小边：Crooked front Folding 欠返针：Miss Back tack唛头字母被盖：Hidden Wordings 子口反骨：Seam Overturn欠开骨：Without Press Open 裤咀歪：Distorted Waistband End 大细唇：Uneven Lips 叠唇：Overlapped Lips裂唇：Open Lips 露朴：Exposure Interlining领咀朴空：Empty Collar Point 反光：Under ply Visible Outside 突钮子：Extension of Right Fly Too Long长短领尖：Uneven Collar Point Length起角：Nose in Extension-Collar /Cuff上领黏边：Folded Edge on Collar Closing内领窝谷：Fullness on Inside Around Collar setting车唛不对折痕：not Following the Folded Mark of Label下级领高低：Crooked Collar Hi-Low/off Center Line布包朴过紧：Tightness of Interlining after Sewing领朴起泡：Bubbling/Delimitation Fused Collar扭：Twisted/Misaligned Underarm and Side Seam打褶Make dart八）中英文色泽名称对照表Amber 琥珀色Khaki 土黄色Amethyst 蓝紫色Leek Green 葱绿色Antique Bronze 古铜色Lilac 淡紫色Brown 棕色Lemon 柠檬色Blue 蓝色Magenta 品红色Burgundy 红紫色Mooney 紫红色Bordeaux 红酱色Copper Brown 棕红色Maroon 酱紫色Brilliant Green 艳绿色Navy Blue 藏青色Black 黑色Orange 橙色Canary 嫩黄色Olive 橄榄色Clay 土灰色Pink 桃红色Salmon Pink橙红色/浅橙色Crimson 梅红色Plum 梅红色Pea Green 豆绿色Carmine 胭脂色Peacock 孔雀蓝Corinth 紫酱色Rubies 酱色Claret 枣红色Dark Blue 深蓝色Malachite Green 孔雀绿Fawn 淡黄褐Royal Blue 品蓝色Flesh Color 肉色Ruby 红玉色Fast Blue 坚牢色Sorrel 红棕色Golden Yellow 金黄色Sky Blue 湖蓝色Golden Brown 黄棕色Scarlet 大红色Grass Green 草绿色Turquoise Blue 翠绿色Grey/Charcoal 灰色Tangerine 桔红色Honey 蜜黄色Violet 紫色Isabella 淡黄色White(off white) 白色(米白) Jade Green 翠绿色Yellow 黄色Mastic 乳白色Red 红色九）物料名词：MATERIAL ITEMAttention Card 注意卡Buckle 字扣，铁扣Back end sticker 外箱检针济贴纸Plastic Butterfly 胶蝴蝶，胶托Button Mould 钮模Boxes 内箱B. Support 胶托（FOR M&S）B. Support 胶托（FOR M&S）Button 钮Carton 外箱Inner Carton 内箱Division Pad 内插筒Shoulder Cotton Pad棉织带Carton Tag 箱贴纸Plastic Clips 胶夹PL. Collar Support 胶领圈Paper Collar Stripe 纸领条Collar Stay 插竹Drawstring 棉绳Elastic Band 细橡根Embroidery Patch 绣花章Cum Tape 平橡根Herringbone Tape 人字带Hook and Eye 安全枢（银色）Plastic Hangers 胶衣架Hang Tag 挂卡Interlining 朴Jocker Tag 挂卡（For Tommy）Lace 丝带，花边Box end Label 内盒贴纸(For M&S) Content Label 成份唛Leather Disc 皮牌Exterior Label 旗唛（For ANF）Flag Label 旗唛，皮士唛Luggage Pin 胶针Item Label 旗唛Zipper Pull 拉链头Main Label 主唛Neck Label 领唛Country Origin Labe l 产地唛Pocket/Placket Label袋唛／旗唛Label of Other 其它唛Size Label 西士唛Wash Care Label 洗水唛Yoke Label 担干唛Content/WC/SZ Lab el 成份／洗水／西士唛Metal Clip 叉字铁夹Magic Sticker 魔术贴Nylon Loop 尼龙捆条Nylon String 尼龙绳Small Poly bag 小胶袋Poly bag 胶袋Plastic Clip 胶夹Poly Envelope 胶袋（封口）Golden Field Pocket Fabric 高丰袋布Piece goods (Job costing) 工作用品Paper Belt （纸）腰带（装饰用）Pins 针Cowhide Pager 牛皮纸Plastic 胶针Paper Tag 纸牌Price Ticket (OCR) 价钱牌Ribbon 丝带Rectangle Clip 方型胶夹Rivet 铆钉Poly bag Sticker 胶袋贴纸Carton Sticker 外箱贴纸Sundries 杂物Safety Pins 扣针Shoulder Pad(Tape) 扁带Inner Box Sticker 内盒纸箱Hang tag Sticker 挂卡贴纸Plastic Shirt Band 胶领条Paper Shirt Band 纸领条Shirt Board 纸板Size Sticker 西士贴纸Sticker 贴纸Glee 胶Staple Wire 备用电线Silicon Wrappers 缎带Levis Tab 转移印花Tag Tin 胶针（用枪打）Tissue Paper 纸领条，衬纸Thread 线Twill Tape 斜纹带Waist Band 印字系带，纸腰带Waist Tag 腰牌Zipper 拉链Plastic Sticker 胶贴纸十）、车缝常用名词中英文对照Linking 缝合Folding 折Crease 折边Slacks side seam 边缝Lapped seam 叠缝Single lapped seam 单线叠缝Blind stitch felling 暗缝线Flat felled seam 折边缝线Back tuck 回针，往复针Double welt seam 双线针Bar tacking 加固针缝Bound seam 包缝Top stitch 边缘明线Pad stitch 衲缝Triple stitch 三针平车，三针直线缝Run stitch 平缝，缝合Run and Turn 回针缝合Run and Open 开口缝Blind over edging 下摆翻边缝Tucked seam 缝褶Dart sewing 省缝Double stitched seam 双线缝，双层缝合Twin needle stitch 针平缝Stitch and Run 头，反缝Wrapping button shank 绕扣线Straight buttonhole 平眼锁钮孔Piped seam 夹紧缝Single lapped seam at edge 单线打边缝Edge stitched seam 边缘缝Lapped seam 包缝Welt seam 咬口折边，折缝Feltings 双折边叠缝，对折缝Button holing 锁眼扣Button sewing 钉纽扣Rolled seam 包边缝Threefold seam 三折缝Fourfold seam 四折缝Fell seam 双折边缝EGMS 界面常用英文单词翻译一、Personal Information 人事资料Transaction 处理，办理Employee Master 雇员Employee No. 雇员编号Employee Name 姓名Rack No. 厂卡号Social Security No. 社会保险号Birth Certificate No. 出生证号Identity No. 身份证号Income Tax No. 纳税号Sex 性别Marital Status 婚姻状况Male 男Female 女No. of Children 子女数Date of Birth 出生日期Join Date 入厂日期Effective Join Date 生效日期Daily Deduction Entry 扣减输入First Contract Date 第一次签合同日Date Leave 离职日期Home Address 家庭住址Area 地区Phone No. 电话号码Search Detail 查找细则Education Grade 学历Cutting Ticket No. 制单Description 描述Update 更新二、Daily Deduction Entry 扣减输入Process 过程Transaction Date 工票日期Daily Allowance Entry 补贴输入Piece and time rate worker时工和件工PO 定单三、Daily Compensate Hour Entry （COM）补时工输入Supplementary增补，追加Overtime Code加班代号Cutting Ticket No. 制单号Daily production Ticket Adjustment Entry工票修改界面Employee Status Control雇员状况Quantity数量Alter Prod Line组别Compensate Hours Entry补时工输入Factory PO制单号Amount金额Price单价Payroll工帐四、Payroll information : 工资资料Factory Code工厂编号Section Code部门Production Line Code组别代码Operation Code（Op. Code）工序号Employee Type雇员类别Job Level工种级别Job Class工种Pay Type付款方式Cash现金支付Labor Type劳动力类型Direct直接体力劳动Indirect非直接体力劳动Remuneration Scheme工资类别Monthly rated月薪Option属性Staff职员Bank Branch Code支行代号Basic Pay Amount基本工资Daily Production Ticket Table Entry工票输入界面Daily Production Ticket By Factory PO Entry工票输入界面Piece rated件薪Time rated时薪Worker工人Bank Code银行代号Bank Account No银行帐户号Employee Status雇员状况五、Piece and Time Rate Worker :计时和计件工人Op. Code工序编号Process Type生产过程描述Cutting裁床Sewing车间Fusing 烫朴Washing洗水Iron 烫部Packing包装六、Daily Production Ticket Normal Entry ：工票输入界面Production Ticket Normal Detail 工票输入细则Production Ticket Normal Header工票输入表头Normal Quantity原数Adjust Quantity修改后的数Daily Production Ticket Supplementary Entry追补工票输入界面Daily Compensate Hours Entry补时工输入界面Daily Allowance Entry补贴输入界面Daily Deduction Entry扣减输入界面Employee Group Setting评分输入界面Group ID组别Ratio Value评分Total Hours总出勤时间Normal正常出勤时间OTx1.5平时加班时间OTx 2周六/日加班时间OTx3法定假日加班时间Factory Suspend Hours回工时间Absent 缺勤时间Leave Descrp. 请假描述Print 打印Report 汇总Data Entry Report 输入资料汇总Print Selection 打印区域Production Ticket (Normal ) Report 工票总结From Page No. 从第页To Page No. 到第页七、Monthly Pay Detail 月薪细则Bank Payment 银行支付Allowance Detail 补贴细则Salaries Detail 薪水细则Deduction Detail 扣减细则Over Time Payment 加班工资Compensation Detail 补时工细则八、Daily Production Ticket Inquire 工票查寻界面Factory PO 制单号Amount 金额Price 单价Query Result 查寻结果中国十大食用油品牌1.金龙鱼益海嘉里集团2.福临门中国粮油食品集团3.鲁花山东鲁花集团有限公司4.多力上海佳格食品葵花油5.盛洲厦门中盛粮油6.汇福三河汇福粮油集团有限公司7.海狮上海良友海狮油脂8.民康江苏民康油脂有限公司9.红蜻蜓重庆市油脂公司10.鹰唛中山市鹰唛食品玉米油十大品牌1.长寿花邹平三星油脂公司有限公司2.西王山东西王沙渥拉油脂有限公司3.金龙鱼益海嘉里集团4.福临门中国粮油食品集团5.融氏上海融氏企业有限公司6.海狮上海良友海狮油脂7.道道全湖南巴陵油脂有限公司8.鹰唛中山市鹰唛食品9.大满贯金光食品（宁波）有限公司10.优沃吉林正望油脂有限公司十大花生油品牌1.鲁花山东鲁花集团有限公司2.金龙鱼益海嘉里集团3.龙大龙大食品集团有限公司4.福临门中国粮油食品集团5.喜燕青岛天翔集团6.星河河南省星河油脂有限公司橄榄油十大品牌1.多力橄榄油上海佳格食品有限公司葵花油2.欧蕾lamasia 西班牙橄榄油3.品利-亿芭利西班牙橄榄油4.阿格力斯argolis 希腊橄榄油5.阿茜娅橄榄油青岛阿茜娅商贸有限公司进口6.欧利维兰意大利橄榄油7.鲁花橄榄油山东鲁花集团橄榄油8.田园乐-优尼雅希腊橄榄油9.金色橄榄油地中海橄榄油。

制衣厂常用术语中英文对照表令狐文艳一）部门术语及常用词A.裁床：Cutting room1 纸样制作原理及方法：The methods & principle of pattern making2 排唛架方法：The methods of marker making3 YPD的计算及工厂唛架利用率：YPD calculation & marker use rate4 拉布及割布方法，工票之使用方法及功用：Methods & function of spreading & cutting5 裁剪日产量：Daily quantity of cutting6 裁单：Cutting ReportB．板房：Sample room1 裤子，恤衫的车缝工序：Understand the procedures of sewing pants and shirt2 熟识各个工序的称谓：Understand the name of various procedures3 熟识各个线缝的名称及功能：Understand the name and function in various seams4 了解缝1件衫所需的辅料：understand sub-materials used in a shirt5 熟识样板制造单：Understand sample orderC．车缝车间1 熟识生产制造单：Understand the production order2 熟识整个生产线的工序安排：Understand the product line lay out3 各个工序的定价标准：Price standard of various process4 质量控制方法：Methods of quality control5 日产量：Daily product quantity6 常见的车缝设备：Work-aids sewing Machine & attachments7 常见的车缝疵点：Various types of sewing problemD.洗水厂 Washing department1 洗水方法及不同的洗水特点：Washing type & various characteristic2 不同洗水的洗涤剂：Various chemical consumption for each type of garment wash3 如何控制洗水质量：Garment washing quality control E．包装：Packing department1 包装工序的任务及要求：What propose with packing process2 包装方法：Types of packing：Stand-up packing：企装, Flat packing：扁装 Semi stand packing: 铲装/半企装3 包装所需的辅料：What assembly will be used in packing4 包装机械设备：Packing equipment5 装箱方法：Methods of packing6 出货所需之文件：Shipping document7 如何控制包装质量：How to control packing quality二）制衣厂质量检查 QC Quality controlB.服装中-英名称衬衣Shirt/Blouse T-恤T-Shirt毛衣Sweat shirt 西装Suit裤子Pants 牛仔裤Jeans喇叭裤子 Bell bottom jeans 裙子Skirt外套Coat 连帽T-恤Parka运动衫Sports jacket 连衣裙Dress圆台裙Circular 百褶裙Gather Skirt裤裙Flare Culottes Skirt 马甲Vest背心Tank top 燕尾领Wing collarC.衣服部位中-英文名称前幅Front 后幅Back上级领Collar 下级领Collar Band前筒Front Placket 钮子Button stay袋Pocket 担干Yoke袖Sleeve 袖侧Sleeve placket介英Cuff 裤头Waist Band耳仔Belt Loop 拉链贴Zipper catch拉链牌Zipper Fly 袋贴Pocket Facing前浪Front Rise 后浪Back Rise裤脚Leg Bottom 侧骨Side Seam袋口Pocket Mouth 袖叉Sleeve Slit机头Riser 明袋Patch Pocket唇袋Jetted Pocket 袋盖Pocket Flap插袋Cross Pocket 袋衬Bearer袋布Pocket Bag 袖口贴Sleeve Band兜帽Hood 夹圈Armhole钮门Button Hole 凤眼Eyelet Button Hole捆条圆领 Crew neckD.制衣工序名称 Garment Product Procedure纸样Pattern 唛架Marker裁剪Cutting 绣花Embroidery样板Sample 车缝Sewing洗水Washing 成衣染Garment Dye整烫Ironing 包装Packing质量检查 Quality Inspection 质量控制Quality Control 石洗Stone Wash 化学洗Chemical Wash茶化洗Teast Wash 漂洗Bleach Wash钮Button 线Thread唛头 /商标Label 挂卡Hang tag贴纸Sticker 朴Interlining胶袋Plastic/Poly bag 胶夹Plastic Clip拉链Zipper 橡根Elastic Band肩垫Shoulder Pad 衬纸Tissue Paper绅Drawstring 领蝴蝶Collar Butterflies 领胶条Collar Stripe 纸箱（Paper）Carton （胶）针(Poly) Pins 检针济Sticker纸板Paper board 蝴蝶Butterfly纸/胶领条 Paper/Plastic collar band 尺码贴纸Size sticker插竹Collar stay 条形码Jan code/bar code E.车缝工序 Sewing process埋夹close side seam 车唛sew label间线子口hem stitch seam上间袖attachsleeve/topstitch sleeve打枣Tacking 接线Joints三）、布的中-英文名称1.梭织布 Woven牛津纺Oxford 府绸Poplin多臂提花Dobby斜纹Twill青年布Chambray 绒布Flannel条格布gingham 泡泡纱Seersucker灯芯绒Corduroy 卡其Drill哔叽Serge 华达呢Gabercord主身布Body fabric撞布Contrast fabric 条格Check 斜纹Stripe净色Solid 支数warp count2.针织布 Knit平纹布Jersey (Drop 1*1 Jersey/Lycry Jersey)珠地Pique (Twill Pique /Oxford pique /Athletic pique)双珠地Lacoste (Oxford Lacoste 牛津珠地)双面布Interlock (interlock pique /interlock jacquard 双面提花)毛圈布Terry ( twill French terry 法兰绒 /Fleece 磨毛毛圈布)提花Jacquard (herringbone /bubble jacquard 泡泡提花布)罗纹Rib (mini waffle 十字罗纹/法式罗纹French rib)棉布Cotton fabric麻布Linen丝绸Silk毛Wool化学纤维Chemical fiber四）制单要求 The requirement in production order生产制单production order 样板制造单Sample order款号Style Number 客户Customer数量quantity 尺码Size spec.交货期Delivery 装箱要求Carton Requirement纸箱规格Carton Measurement 毛重Crossheight净重Net height 说明Description 目的地Final destination 颜色color五）、其它样板Sample 货前板Pre-Production sample销售板Sales Sample 展览板Presentation sample批准板Approval sample 会议板Meeting Sample测试板Test sample 船头办Pre-shipment Sample六）布疵常见术语紧纱：Tight 断纱：Broken Yarn走纱：Misend / Mispick 抽纱：Yarn with Drawn针孔：Needle Holes 针路：Vertical Line横间：Horizontal Line 漏针：Dropped Stitch停机布痕：Stop Mark 幼纱：Yarn Thinning/Thin Yarn错花：Wrong Pattern or Wrong Structure飞花：Fly yarn 色差Shading染色Color fastness 粗纱Thick yarn色纱Color yarn织错纱Wrong pick end稀密路Filling bar 布纹弯曲不平 Bowing皱摺Crease 粗粒Slub起毛Hairy 织入杂物Gout起球Balling-up七）车缝常见术语跳线：Skip Stitch 用错原料：Wrong Material缝线散口：Run off 用错缝线：Incorrect Thread错唛：Wrong Label 破洞：Holes突咀：Excess Extension 不对称：Mismatched车着唛头：Sandwich Label 歪唛：Off Center or Side left/right尖位不尖：Pointed Area not Sharp 弯位不弯：Unsmooth Curve爆口：Open Seam 披苏：Loose Thread插竹歪：Crooked Collar Stay 领底松：Collar setting too Loose烂钮尖：Burst Collar Point 领尖不对条：Mismatched Collar Stripe错领型：Wrong Collar Shape 刀剪领：Scissoring露上领线：Thread Visible Outside 下级走样：Poor Banding领咀长短不定：Wrong Lapel Length 领错底面：Overturn Collar起耳子：Lock stitches-loop 断线：Broken Stitches落坑：Run off Stitch 积线球：Lumps of Thread藏色线：Trapped Color Thread 驳线不齐：Untidy Joined Stitching缝线阔窄：Uneven Seam 线路不美：Untidy Stitching皱：Pocking 露牙：Grinning走鸡：Miss Design Feature 大眼皮：Uneven seam高底袋：High/low pocket 筒起波浪：Fullness on Center Placket筒歪：Crooked Center Placket 担干谷：Fullness on Yoke前肩大小边：Crooked front Folding 欠返针：Miss Back tack唛头字母被盖：Hidden Wordings 子口反骨：Seam Overturn欠开骨：Without Press Open 裤咀歪：Distorted Waistband End大细唇：Uneven Lips 叠唇：Overlapped Lips裂唇：Open Lips 露朴：ExposureInterlining领咀朴空：Empty Collar Point 反光：Under ply Visible Outside突钮子：Extension of Right Fly Too Long长短领尖：Uneven Collar Point Length起角：Nose in Extension-Collar /Cuff上领黏边：Folded Edge on Collar Closing 内领窝谷：Fullness on Inside Around Collar setting车唛不对折痕：not Following the Folded Mark of Label下级领高低：Crooked Collar Hi-Low/off Center Line布包朴过紧：Tightness of Interlining after Sewing领朴起泡：Bubbling/Delimitation Fused Collar扭：Twisted/Misaligned Underarm and Side Seam打褶Make dart八）中英文色泽名称对照表Amber 琥珀色Khaki 土黄色Amethyst 蓝紫色Leek Green 葱绿色Antique Bronze 古铜色Lilac 淡紫色Brown 棕色Lemon 柠檬色Blue 蓝色Magenta 品红色Burgundy 红紫色Mooney 紫红色Bordeaux 红酱色Copper Brown 棕红色Maroon 酱紫色Brilliant Green 艳绿色Navy Blue 藏青色Black 黑色Orange 橙色Canary 嫩黄色Olive 橄榄色Clay 土灰色Pink 桃红色Salmon Pink橙红色/浅橙色Crimson 梅红色Plum 梅红色Pea Green 豆绿色Carmine 胭脂色Peacock 孔雀蓝Corinth 紫酱色Rubies 酱色Claret 枣红色Dark Blue 深蓝色Malachite Green 孔雀绿Fawn 淡黄褐Royal Blue 品蓝色Flesh Color 肉色Ruby 红玉色Fast Blue 坚牢色Sorrel 红棕色Golden Yellow 金黄色Sky Blue 湖蓝色Golden Brown 黄棕色Scarlet 大红色Grass Green 草绿色Turquoise Blue 翠绿色Grey/Charcoal灰色Tangerine 桔红色Honey 蜜黄色Violet 紫色Isabella 淡黄色White(off white) 白色(米白)Jade Green 翠绿色Yellow 黄色Mastic 乳白色Red 红色九）物料名词：MATERIAL ITEMAttention Card 注意卡Buckle 字扣，铁扣Back end sticker 外箱检针济贴纸Plastic Butterfly 胶蝴蝶，胶托Button Mould 钮模Boxes 内箱B. Support 胶托（FOR M&S）B. Support 胶托（FOR M&S）Button 钮Carton 外箱Inner Carton 内箱Division Pad 内插筒Shoulder Cotton Pad棉织带Carton Tag 箱贴纸Plastic Clips 胶夹PL. Collar Support 胶领圈Paper Collar Stripe 纸领条Collar Stay 插竹Drawstring 棉绳Elastic Band 细橡根Embroidery Patch 绣花章Cum Tape 平橡根Herringbone Tape 人字带Hook and Eye 安全枢（银色）Plastic Hangers 胶衣架Hang Tag 挂卡Interlining 朴Jocker Tag 挂卡（For Tommy）Lace 丝带，花边Box end Label 内盒贴纸(For M&S) Content Label 成份唛Leather Disc 皮牌Exterior Label 旗唛（For ANF）Flag Label 旗唛，皮士唛Luggage Pin 胶针Item Label 旗唛Zipper Pull 拉链头Main Label 主唛Neck Label 领唛Country Origin Labe l 产地唛Pocket/Placket Label袋唛／旗唛Label of Other 其它唛Size Label 西士唛Wash Care Label 洗水唛Yoke Label 担干唛Content/WC/SZ Lab el 成份／洗水／西士唛Metal Clip 叉字铁夹Magic Sticker 魔术贴Nylon Loop 尼龙捆条Nylon String 尼龙绳Small Poly bag 小胶袋Poly bag 胶袋Plastic Clip 胶夹Poly Envelope 胶袋（封口）Golden Field Pocket Fabric 高丰袋布Piece goods (Job costing) 工作用品Paper Belt （纸）腰带（装饰用）Pins 针Cowhide Pager 牛皮纸Plastic 胶针Paper Tag 纸牌Price Ticket (OCR) 价钱牌Ribbon 丝带Rectangle Clip 方型胶夹Rivet 铆钉Poly bag Sticker 胶袋贴纸Carton Sticker 外箱贴纸Sundries 杂物Safety Pins 扣针Shoulder Pad(Tape) 扁带Inner Box Sticker 内盒纸箱Hang tag Sticker 挂卡贴纸Plastic Shirt Band 胶领条Paper Shirt Band 纸领条Shirt Board 纸板Size Sticker 西士贴纸Sticker 贴纸Glee 胶Staple Wire 备用电线Silicon Wrappers 缎带Levis Tab 转移印花Tag Tin 胶针（用枪打）Tissue Paper 纸领条，衬纸Thread 线Twill Tape 斜纹带Waist Band 印字系带，纸腰带Waist Tag 腰牌Zipper 拉链Plastic Sticker 胶贴纸十）、车缝常用名词中英文对照Linking 缝合Folding 折Crease 折边Slacks side seam 边缝Lapped seam 叠缝Single lapped seam 单线叠缝Blind stitch felling 暗缝线Flat felled seam 折边缝线Back tuck 回针，往复针Double welt seam 双线针Bar tacking 加固针缝Bound seam 包缝Top stitch 边缘明线Pad stitch 衲缝Triple stitch 三针平车，三针直线缝Run stitch 平缝，缝合Run and Turn 回针缝合Run and Open 开口缝Blind over edging 下摆翻边缝Tucked seam 缝褶Dart sewing 省缝Double stitched seam 双线缝，双层缝合Twin needle stitch 针平缝Stitch and Run 头，反缝Wrapping button shank 绕扣线Straight buttonhole 平眼锁钮孔Piped seam 夹紧缝Single lapped seam at edge 单线打边缝Edge stitched seam 边缘缝Lapped seam 包缝Welt seam 咬口折边，折缝Feltings 双折边叠缝，对折缝Button holing 锁眼扣Button sewing 钉纽扣Rolled seam 包边缝Threefold seam 三折缝Fourfold seam 四折缝Fell seam 双折边缝EGMS 界面常用英文单词翻译一、Personal Information 人事资料Transaction 处理，办理Employee Master 雇员Employee No. 雇员编号Employee Name 姓名Rack No. 厂卡号Social Security No. 社会保险号Birth Certificate No. 出生证号Identity No. 身份证号Income Tax No. 纳税号Sex 性别Marital Status 婚姻状况Male 男Female 女No. of Children 子女数Date of Birth 出生日期Join Date 入厂日期Effective Join Date 生效日期Daily Deduction Entry 扣减输入First Contract Date 第一次签合同日Date Leave 离职日期Home Address 家庭住址Area 地区Phone No. 电话号码Search Detail 查找细则Education Grade 学历Cutting Ticket No. 制单Description 描述Update 更新二、Daily Deduction Entry 扣减输入Process 过程Transaction Date 工票日期Daily Allowance Entry 补贴输入Piece and time rate worker 时工和件工PO 定单三、Daily Compensate Hour Entry （COM）补时工输入Supplementary增补，追加Overtime Code加班代号Cutting Ticket No. 制单号Daily production Ticket Adjustment Entry工票修改界面Employee Status Control雇员状况Quantity数量Alter Prod Line组别Compensate Hours Entry补时工输入Factory PO制单号Amount金额Price单价Payroll工帐四、Payroll information : 工资资料Factory Code工厂编号Section Code部门Production Line Code组别代码Operation Code（Op. Code）工序号Employee Type雇员类别Job Level工种级别Job Class工种Pay Type付款方式Cash现金支付Labor Type劳动力类型Direct直接体力劳动Indirect非直接体力劳动Remuneration Scheme工资类别Monthly rated月薪Option属性Staff职员Bank Branch Code支行代号Basic Pay Amount基本工资Daily Production Ticket Table Entry工票输入界面Daily Production Ticket By Factory PO Entry工票输入界面Piece rated件薪Time rated时薪Worker工人Bank Code银行代号Bank Account No银行帐户号Employee Status雇员状况五、Piece and Time Rate Worker :计时和计件工人Op. Code工序编号Process Type生产过程描述Cutting裁床Sewing车间Fusing 烫朴Washing洗水Iron 烫部Packing包装六、Daily Production Ticket Normal Entry ：工票输入界面Production Ticket Normal Detail 工票输入细则Production Ticket Normal Header工票输入表头Normal Quantity原数Adjust Quantity修改后的数Daily Production Ticket Supplementary Entry追补工票输入界面Daily Compensate Hours Entry补时工输入界面Daily Allowance Entry补贴输入界面Daily Deduction Entry扣减输入界面Employee Group Setting评分输入界面Group ID组别Ratio Value评分Total Hours总出勤时间Normal正常出勤时间OTx1.5平时加班时间OTx 2周六/日加班时间OTx3法定假日加班时间Factory Suspend Hours回工时间Absent 缺勤时间Leave Descrp. 请假描述Print 打印Report 汇总Data Entry Report 输入资料汇总Print Selection 打印区域Production Ticket (Normal ) Report 工票总结From Page No. 从第页To Page No. 到第页七、Monthly Pay Detail 月薪细则Bank Payment 银行支付Allowance Detail 补贴细则Salaries Detail 薪水细则Deduction Detail 扣减细则Over Time Payment 加班工资Compensation Detail 补时工细则八、Daily Production Ticket Inquire 工票查寻界面Factory PO 制单号Amount 金额Price 单价Query Result 查寻结果。

生产类专有名词组织机构及职位XX电子有限公司XX Electronics CO., Ltd总经理办公室General manager’s office企管部Enterprise management department (EM)行政部Administration department (AD)销售部Sales department (SD)财务部Financial department (FD)技术部Technology department (TD)物控部Production material control department (PMC)生产部Production department(PD)模具部Mold manufacturing department, Tooling manufacturing department (TM) 品管部Quality Assurance department (QA)冲压车间Stamp workshop, press workshop注塑车间injection workshop装配车间Assembly workshop模具装配车间Mold and die Assembly workshop金属加工车间Metal machine workshop电脉冲车间Electric discharge process workshop线切割车间wire cutting process workshop工磨车间Grinding workshop总经理General manager (GM)副总经理Vice-general manager经理manager董事长president副董事长Vice-presidentXX部门经理Manager of XX department主任、主管supervisor拉长Line leader组长Foreman, forelady秘书secretary文员clerk操作员operator助理assistant职员staff连接器connector端子terminal条型连接器bar connector阴连接器Housing阳连接器wafer线束wire harness间距space额定电压rated voltage额定电流rated current接触电阻contact resistance绝缘电阻insulation resistance超声波焊接ultrasonic welding耐压withstand voltage针pin物料编号part number导线wire基体金属Base metal电缆夹cable clamp倒角chamfer接触面积contact area接触件安装孔contact cavity接触长度contact length接触件电镀层contact plating接触压力contact pressure接触件中心距contact space接触簧片contact spring插孔socket contact法兰、凸缘Flange界面间隙interfacial gap键Key键槽keyway过渡段ramp屏蔽套shielding定位基准Datum reference扁平电缆flat cable ，Ribbon cable柔性印刷电线Flexible printed wiring 多层印制电路Multilayer printed circuit 焊盘pad图形pattern间距pitch负极Negative pole正极positive pole原理图Schematic diagram单面板single sided board双面板Two-sided board，Double-sided board表面安装surface Mounting翘曲warp，bow波峰焊wave soldering编织层braid同轴电缆coaxial cable电介质dielectric电缆中导线的头数ends外部干扰external interference填充物filler护套jacket比重specific gravity电阻的温度系数Temperature coefficient of resistance 三、模具塑料模具mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plateTop plateFixed clamp plate水口推板stripper plateA板A plateB板B plate支承板support plate方铁spacer plate底针板ejector plate面针板ejector retainer plate回针Return pin导柱Guide pin有托导套Shoulder Guide bush直导套Straight Guide bush动模座板Bottom clamp plateMoving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate凸模固定板punch-retainer plate顶针ejector pin单腔模具single cavity mould多腔模具multi-cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate 料穴cold-slug well浇口套sprue bush流道板runner plate排飞槽vent分型线（面）parting line定模stationary mould，Fixed mould动模movable mould, movable half上模upper mould，upper half下模lower mould，lower half型腔cavity凹模cavity plate，cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹weld line （flow line）三板式模具three plate mould脱模ejection换模腔模具interchangeable cavity mould脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould，cavity block阳模male mould电加工设备Electron Discharge Machining数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller 立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine 四、品管SPC statistic process control品管保证Quality Assurance品管控制Quality control来料检验IQC Incoming quality control巡检IPQC In-process quality control校对calibration动态试验dynamic test环境试验Environmental test非破坏性试验non-destructive test光泽gloss击穿电压(dielectric) breakdown voltage拉伸强度tensile strength冷热骤变试验thermal shock test环境试验炉Environmental chamber盐雾实验salt spray test绝缘电阻测试验仪Insulating resistance meter 内应力internal stress疲劳fatigue蠕变creep试样specimen撕裂强度tear strength缩痕shrink mark, sink mark耐久性durability抽样sampling样品数量sample sizeAQL Acceptable Quality level批量lot size抽样计划sampling planOC曲线operation curve试验顺序sequence of tests环境温度ambient temperature可焊性solderability阻燃性flame resistance五、生产注塑机injection machine冲床Punch machine混料机blender mixer尼龙nylon黄铜brass青铜bronze紫(纯)铜copper料斗hopper麻点pit配料compounding涂层coating飞边flash预热preheating再生料reworked material再生塑料reworked plastics工艺设计process design紧急停止emergency stop延时time delay六．物控保质期shelf lifeABC分类法ABC Classification反常需求Abnormal Demand措施信息Action Message活动报告标志Action-report-flag基于活动的成本核算Activity-based Costing (ABC) 实际能力Actual Capacity实际成本Actual Costs调整现有库存量Adjust-on-hand已分配量Allocation替代工序Alternative Routine装配订单Assembly Order装配零件表Assembly Parts List装配Assembly计划自动重排Automatic Rescheduling可达到库存Available Inventory可用材料Available Material达到库存Available Stock可利用工时Available Work可签约量Available-to-promise平均库存Average Inventory欠交订单Back Order倒序计划Back Scheduling倒冲法Back flush未完成订单Backlog现有库存余额Balance-on-hand Inventory批号Batch Number批量生产Batch Production标杆瞄准Benchmarking工时清单Bill of Labor提货单Bill of Lading物料清单Bill of Material分库Branch Warehouse经营规划Business Plan采购员Buyer能力管理Capacity Management能力需求计划Capacity Requirements Planning (CRP) 保管费率Carrying Cost Rate保管费Carrying Cost单元式制造Cellular Manufacturing修改批量日期Change Lot Date修改工序Change Route修改产品结构Change Structure检查点Check Point闭环物料需求计划Closed Loop MRP通用工序标识Common Route ID计算机集成制造Computer-integrated Manufacturing (CIM)配置代码Configuration Code约束管理/约束理论Constraints Management/Theory of Constraints (TOC) 依成本的材料清单Costed Bill of Material急需零件Critical Part累计提前期Cumulative Lead Time现有运转时间Current Run Hour现有运转数量Current Run Quantity周期盘点Cycle Counting调整日期Date Adjust有效日期Date Available修改日期Date Changed结束日期Date Closed截止日期Date Due生产日期Date in Produced库存调整日期Date Inventory Adjust作废日期D ate Obsolete收到日期Date Received交付日期Date Released需求日期Date Required发货日期Date to Pull空负荷Dead Load需求管理Demand Management需求Demand实际能力Demonstrated Capacity非独立需求Dependent Demand直接增减库存处理法Direct-deduct Inventory Transaction Processing发料单Disbursement List派工单Dispatch List分销资源计划Distribution Resource Planning (DRP)鼓－缓冲－绳子Drum-buffer-rope经济订货批量Economic Order Quantity (EOQ)工程变更生效日期Engineering Change Effect Date工程变更生效单Engineering Change Effect Work Order工程停止日期Engineering Stop Date例外控制Exception Control呆滞材料分析Excess Material Analysis急送代码Expedite Code加工订单Fabrication Order补足欠交Fill Backorder总装提前期Final Assembly Lead Time确认的计划订单Firm Planned Order固定订货批量F ixed Order Quantity集中预测Focus Forecasting完全跟踪Full Pegging通用生产管理原则Generally Accepted Manufacturing Practices 毛需求Gross Requirements在制品库存In Process Inventory独立需求Independent Demand投入/产出控制Input/ Output Control检验标识Inspection ID厂际需求Interplant Demand库存周转率Inventory Carry Rate仓库库位类型Inventory Location Type库存周转次数Inventory Turnover发送订单Issue Order项目记录Item Record物料项目Item加工车间Job Shop准时制生产Just-in-time (JIT)看板Kanban人工工时Labor Hour最后运输日期Last Shipment Date提前期Lead Time层Level负荷量Load Leveling负荷报告Load Report负荷Load仓位代码Location Code仓位备注Location Remarks仓位状况Location Status按需订货Lot for Lot批量标识Lot ID批量编号Lot Number批量Lot Size低位码Low Level Code机器能力Machine Capacity机器加载Machine Loading外购或自制决策Make or Buy Decision面向订单生产的产品Make-to-order Product面向库存生产的产品Make-to-stock Product制造周期时间Manufacturing Cycle Time制造资源计划Manufacturing Resource Planning (MRP II)主生产计划Master Production Schedule (MPS)物料成本Material Cost物料发送和接收Material Issues and Receipts物料需求计划Material Requirements Planning (MRP)登陆标志MPS Book Flag MPS多重仓位Multiple Location净改变式MRP N et Change MRP净需求Net Requirements新仓位New Location新组件New Parent新仓库New Warehouse不活动报告No Action Report现有库存量On-hand Balance未结订单Open Order订单输入Order Entry订货点Order Point订货方针Order Policy订货承诺Order Promising订货备注Order Remarks双亲Parent零件清单Part Bills零件批次Part Lot零件编号Part Number零件Part反查Pegging领料单Picking List领料/提货Picking计划订单Planned Order后减库存处理法Post-deduct Inventory Transaction Processing 前减库存处理法Pre-deduct Inventory Transaction Processing 发票价格Price Invoice采购订单价格Price Purchase Order优先计划Priority Planning产品控制Product Control产品线Production Line生产规划编制Production Planning产品率Production Rate产品结构树Production Tree预计可用库存Projected Available Balance采购订单跟踪Purchase Order Tracking已分配量Quantity Allocation仓位数量Quantity At Location欠交数量Quantity Backorder完成数量Quantity Completion需求量Quantity Demand毛需求量Quantity Gross进货数量Quantity In排队时间Queue Time队列Queue重生成式MRP Regenerated MRP重排假设Rescheduling Assumption资源需求计划Resource Requirements Planning粗能力计划Rough-cut Capacity Planning工艺路线Routing安全库存量Safety Stock保险期Safety Time预计入库量Scheduled Receipt残料率Scrap Factor发送零件Send Part维修件Service Parts发货地址Ship Address发货单联系人Ship Contact发货零件Ship Date发货单Ship Order工厂日历Shop Calendar车间作业管理Shop Floor Control损耗系数Shrinkage Factor标准产品成本Standard Product Cost标准机器设置工时Standard Set Up Hour标准单位运转工时Standard Unit Run Hour标准工资率Standard Wage Rate状况代码Status Code库存控制Stores Control建议工作单Suggested Work Order约束理论Theory of Constraints (TOC)时间段Time Bucket时界Time Fence单位成本Unit Cost采购计划员Vendor Scheduler采购计划法Vendor Scheduling工作中心能力Work Center Capacity工作中心Work Center在制品Work in Process工作令跟踪Work Order Tracking工作令Work Order工作进度安排Work Scheduling零库存Zero Inventories经济订货批量＝Squat(2*年订货量*平均一次订货准备所发生成本/每件存货的年储存成本) 美国生产和库存控制协会APICS，American Production & Inventory Control Society 七．QS-9000中的术语APQP Advanced Product Quality Planning and Control Plan，产品质量先期策划和控制计划PPAP Production Part Approval Process,生产件批准程序FMEA Potential Failure Mode and Effects Analysis,潜在失效模式及后果分析MSA Measure System Analysis,测量系统分析SPC Statistical Process Control,统计过程控制审核Audit能力Capability能力指数Capability Indices控制计划Control Plans纠正措施Corrective Action文件Documentation作业指导书Job Instruction, work instruction不合格品Nonconformance不合格Nonconformity每百万零件不合格数Defective Parts Per Million, DPPM 预防措施Preventive Action程序Procedures过程流程图Process Flow Diagram, Process Flow Chart 质量手册Quality Manual质量计划Quality Plan质量策划Quality Planning质量记录Quality Records原始数据Raw Data反应计划Reaction Plan返修Repair。

日常用语中英文对照表repair修理president董事长dryer烘干机operator作业员general manager总经理induction感应QC品管special assistant manager特助concave凸supervisor 课长factory director厂长convex凹ME 制造工程师department director部长nick缺口MT 制造生技deputy manager | =vice manager副理magnalium镁铝合金cosmetic inspect 外观检查section supervisor课长magnesium镁金inner parts inspect 内部检查group leader/supervisor组长metal plate钣金lbs. inch 镑、英寸line supervisor线长lathe车 mill锉chassis 基座assistant manager助理plane刨bezel panel 面板defective to staking铆合不良grind磨Hi-pot test of SPS 高源高压测试embedded lump镶块drill铝production capacity生产力feeding is not in place送料不到位boring镗education and training教育与训练stamping-missing漏冲blinster气泡proposal improvement提案改善to move, to carry, to handle搬运fillet镶;嵌边sheet metal parts 冲件be put in storage入库through-hole form通孔形式plastic parts 塑胶件pack packing包装voller pin formality滚针形式SOP 制造作业程序to apply oil擦油cam driver铡楔material check list 物料检查表to file burr 锉毛刺shank摸柄personnel resource department 人力资源部final inspection终检crank shaft曲柄轴production department生产部门to connect material接料augular offset角度偏差planning department企划部to reverse material 翻料velocity速度QC Section品管科Tiana天那水production tempo生产进度现状stamping factory冲压厂cleaning cloth抹布torque扭矩painting factory烤漆厂to load material上料spline=the multiple keys花键molding factory成型厂to unload material卸料quenching淬火common equipment常用设备to return material/stock to退料tempering回火uncoiler and straightener整平机scraped 报废annealing退火punching machine 冲床scrape ..v.刮;削carbonization碳化robot机械手deficient purchase来料不良tungsten high speed steel钨高速的hydraulic machine油压机manufacture procedure制程moly high speed steel钼高速的lathe车床deficient manufacturing procedure制程不良organic solvent有机溶剂planer |plein|刨床oxidation 氧化bracket小磁导miller铣床scratch刮伤liaison联络单grinder磨床dents压痕volatile挥发性linear cutting线切割molding成型resistance电阻electrical sparkle电火花coordinate座标ion离子welder电焊机sand blasting喷沙titrator滴定仪staker=reviting machine铆合机derusting machine除锈机beacon警示灯position职务degate打浇口coolant冷却液crusher破碎机Lathe bench 车床工作台NC grinding machine NC磨床3D coordinate measurement 三次元量床Lathes,automatic 自动车床 NC lathe NC车床boring machine 搪孔机Lathes,heavy-duty 重型车床NC programming system NC程式制作系统cnc milling machine CNC铣床Lathes,high-speed 高速车床 planer 龙门刨床contouring machine 轮廓锯床Lathes,turret 六角车床profile grinding machine 投影磨床copy grinding machine 仿形磨床Lathes,vertical 立式车床 projection grinder 投影磨床copy lathe 仿形车床Lubricants 润滑液radial drilling machine 旋臂?床copy milling machine 仿形铣床Lubrication Systems 润滑系统shaper 牛头刨床copy shaping machine 仿形刨床Lubricators 注油机surface grinder 平面磨床cylindrical grinding machine 外圆磨床Machining centers,general 通用加工中心try machine 试模机die spotting machine 合模机Machining centers,horizontal 卧式加工中心turret lathe 转塔车床drilling machine ?孔机Machining centers,horizontal & vertical 卧式及立式加工中心universal tool grinding machine 万能工具磨床engraving machine 雕刻机Machining centers,vertical 立式加工中心vertical machine center 立式加工制造中心engraving E.D.M. 雕模放置加工机Machining centers,vertical double-column type 立式双柱加工中心wire E.D.M. 线割放电加工机form grinding machine 成形磨床Magnetic tools 磁性工具3-Jaws indexing spacers 三爪、分割工具头graphite machine 石墨加工机Manifolds 集合管 A.T.C.system 加工中心机刀库horizontal boring machine 卧式搪孔机Milling heads 铣头Aluminum continuous melting & holding furnaces 连续溶解保温炉horizontal machine center 卧式加工制造中心Milling machines 铣床Balancing equipment 平衡设备internal cylindrical machine 内圆磨床Milling machines,bed type 床身式铣床Bayonet 卡口jig boring machine 冶具搪孔机Milling machines,duplicating 仿形铣床Bearing fittings 轴承配件jig grinding machine 冶具磨床Milling machines,horizontal 卧式铣床Bearing processing equipment 轴承加工机lap machine 研磨机Milling machines,turret vertical 六角立式铣床Bearings 轴承machine center 加工制造中心Milling machines,universal 万能铣床Belt drive 带传动multi model miller 靠磨铣床Milling machines,vertical 立式铣床Bending machines 弯曲机NC drilling machine NC钻床Milling machines,vertical & horizontal 立式及卧式铣床Blades 刀片Clamping/holding systems 夹具/支持系统CNC toolings CNC刀杆Blades,saw 锯片CNC bending presses 电脑数控弯折机CNC wire-cutting machines 电脑数控线切削机Bolts,screws & nuts 螺栓,螺帽及螺丝CNC boring machines 电脑数控镗床Conveying chains 输送链Boring heads 搪孔头CNC drilling machines 电脑数控钻床Coolers 冷却机Boring machines 镗床CNC EDM wire-cutting machines 电脑数控电火花线切削机Coupling 联轴器Cable making tools 造线机CNC electric discharge machines 电脑数控电火Crimping tools 卷边工具Casting,aluminium 铸铝花机CNC engraving machines 电脑数控雕刻机Cutters 刀具Casting,copper 铸铜CNC grinding machines 电脑数控磨床Cutting-off machines 切断机Casting,gray iron 铸灰口铁CNC lathes 电脑数控车床Diamond cutters 钻石刀具Casting,malleable iron 可锻铸铁CNC machine tool fittings 电脑数控机床配件Dicing saws 晶圆切割机Casting,other 其他铸造CNC milling machines 电脑数控铣床Die casting dies 压铸冲模Casting,steel 铸钢CNC shearing machines 电脑数控剪切机Die casting machines 压铸机Chain drive 链传动Dies-progressive 连续冲模Engraving machines,laser 激光雕刻机Disposable toolholder bits 舍弃式刀头Etching machines 蚀刻机Drawing machines 拔丝机Finishing machines 修整机Drilling machines 钻床Fixture 夹具Drilling machines bench 钻床工作台Forging dies 锻模Drilling machines,high-speed 高速钻床Forging,aluminium 锻铝Drilling machines,multi-spindle 多轴钻床Forging,cold 冷锻Drilling machines,radial 摇臂钻床Forging,copper 铜锻Drilling machines,vertical 立式钻床Forging,other 其他锻造drills 钻头Forging,steel 钢锻Electric discharge machines(EDM) 电火花机Foundry equipment 铸造设备Electric power tools 电动刀具Gear cutting machines 齿轮切削机Engraving machines 雕刻机Gears 齿轮Lapping machines 精研机Gravity casting machines 重力铸造机Lapping machines,centerless 无心精研机Grinder bench 磨床工作台Laser cutting 激光切割Chain making tools 造链机Laser cutting for SMT stensil 激光钢板切割机Chamfer machines 倒角机Jigs 钻模Chucks 夹盘Heat preserving furnaces 保温炉Heating treatment funaces 熔热处理炉Honing machines 搪磨机Hydraulic components 液压元件Hydraulic power tools 液压工具Hydraulic power units 液压动力元件Hydraulic rotary cylinders 液压回转缸Grinding machines,centerless 无心磨床Grinding machines,cylindrical 外圆磨床Grinding machines,universal 万能磨床Grinding tools 磨削工具Grinding wheels 磨轮Hand tools 手工具Grinders,thread 螺纹磨床Grinders,tools & cutters 工具磨床Grinders,ultrasonic 超声波打磨机Grinding machines 磨床。

序號English Chinese序號English Chinese1Oxidation氧化41Label /Logo wrong ormissing標簽貼錯、漏貼2Stained with tin沾錫42Screw loosen螺絲未鎖緊3Component Dirty零件不潔43Screw thread damaged螺絲滑牙4Glue Spiller溢膠44Gap out of SPEC間隙太大5Without Glue未點膠45Cable improper assembly排線裝反6Scartch刮傷46Name plate fall off銘板脫落7Coating脫漆47Box broken彩盒破損8Painting stripped裂痕48Shortage of part缺配件9Distortion變形49Shortage of pad缺腳墊10Unidentify of value forpart零件值無法識別50Shortage of screw缺螺絲11Solder ball錫珠51Shortage of name plate缺銘板12Lightning stroke雷擊52Foreign matter有異物(含腳渣) 13PCB corrode moldy腐蝕/發霉/生銹53Gold finger dirty金手指不潔14Wrong F/W F/W錯誤54Chromatism外觀顏色色差15Wrong Country code Country code錯誤55LED no light LED不亮16Wrong Feature bite Feature bite錯誤56Stanted of LED LED 歪斜17Wrong F/W Check sum F/W Check sum不對57Wrong colour of LED LED顏色不對18Romfile error Romfile錯誤58No character on LCD LCD無字幕19RAS fail RAS錯誤59No background light of LCD LCD無背光20Download WrongF/WD/L錯誤F/W60Error code of LCD LCD出現亂碼21F/W Data loss F/W資料遺失61Tin tip錫尖22Green painting fall off綠漆脫落62PCB exploded爆板23Component stand up零件高翹/翹件63Part exploded爆件24Short circuit短路64Extra AK part多配件常用詞語中英文對照25Wrong part錯件65Wrong content of S/N code序號Code內容不對26Damaged part損件66Unmatched S/N of box and內外箱序號不符carton27Open soldering空焊67No power無電源28Cold solder冷焊/假焊68No response無動作29Reversed component极性反69Noise雜音30Lead not insert腳未出70Speaker can not work喇叭無聲/異常31Part shift零件位移71Other其他32Tombstoning墓碑效應72Wrong cover用錯上蓋33Extra Part多件73Wrong name plate用錯銘板34Missing parts缺件74No ringing電話不響35Wrong location錯位75Check fixture治具確認36Long lead腳太長7637Side up翻件/側立7738Not open or close key未開關Key7839Shortage of part短缺(數量不足)7940Button function NG按鍵不良80。