不良品项目定义中英文对照版

S01 刮伤﹕受尖锐硬物划碰而在零件表面留下的,长度相对於宽度和深度较长的线状痕迹S02 毛刺﹕产品冲裁后留在零件剪切边的批锋S03 模痕﹕模具在成形零件过程中造成的均匀类似刮痕现象S04 压伤﹕由于模具表面有异物﹐使产品在冲压成形过程中受压力作用在表面留下块状的下凹的现象S05 切边不齐﹕产品冲裁后零件剪切边呈现出不整齐的现象S06 晃动:由于产品平面度超出spec﹐而呈现出凹凸不平的现象S07 尺寸超差﹕产品的尺寸超出SpecS08 材料外观不良﹕原材料本身就具有的一些如白斑﹐黑点 ,麻点﹐发黑﹐白灰﹐刮伤﹐氧化等方面的不良S09 抽牙不良﹕抽牙尺寸超出Spec﹐或是出现抽牙抽歪﹐抽牙抽裂的现象S10 攻牙不良﹕攻牙孔攻歪﹐通规不通﹐止规不止﹐或是出现实配螺丝打不进,实配螺丝滑牙的现象S11 铆合不良﹕铁件铆合后﹐铁件与铁件间间隙超Spec﹐或铆合孔偏位﹐铆合不牢固之现象S12 凸包/拱桥冲裂﹕受模具﹐冲床压力﹐或材料硬度的影响﹐产品在成形过程中凸包/拱桥表面产生明显的裂纹﹐或完全开裂的现象S13 少工程﹕产品成形的工程数少于作业文件所规定的工程数的现象S14 变形﹕由于受外力作用﹐产品失去其本身所应具有的形状的现象S15 生锈﹕基体材料表面或切边呈现经色﹐发生化学氧化的现象S16 不洁﹕产品表面附着除油污﹐毛刺以外的其它异物S17 油污﹕粘附於零件表面能擦除的呈块状或膜状的油脂或变色异物S18 碰刮伤﹕受尖锐硬物刮碰而在零件表面留下的﹐长度相对於宽度和深度较长的表面斑痕S19 包装不良﹕产品的包装方式未完全按照相应的作业文件来执行﹐可能会造成品质隐患的现象S20 混料﹕两种或两种以上的产品同时放置在某单一产品所存放的区域S21 点焊不良﹕产品点焊后铁件与铁件间连接不牢固﹐拉力测试超Spec.存在点焊点错位﹐漏焊,虚焊,烧穿,焊渣等缺陷的现象S22 字模不清/残缺/错误﹕Mark 字体不完整﹐模糊不清﹐字模的位置﹐式样等未完全按作业文件要求作业的现象?5.2.2 涂装不良项目定义P01 杂质:由于烤漆面粘附有杂质﹐烤漆后在表面形成一种凸起的可剥落的块状或点状漆的现象P02 刮伤/掉漆﹕烤漆表面在外力(碰撞﹐擦刮)作用下﹐漆层呈点状﹐块状或成线状(刮伤)破坏﹐可见或不可见底材的不良现象P03 凝漆﹕由于雾化不良或油漆未完全溶解造成在烤漆表面形成凸包状漆块的现象P04 发白﹕烤漆面受手指或包材碰擦﹐目视烤漆面有不同于烤漆本体颜色的白色痕迹P05 喷漆不良均匀﹕烤漆面油漆形成高低不平﹐或膜厚不一致的现象P06 少喷漆﹕产品的烤漆区域少于作业文件所规定的烤漆区域﹐或烤漆的膜厚太低﹐未达到所规定的标准P07 溢漆﹕烤漆时油漆雾化到非烤漆区域的现象P08 漆层剥落﹕由于油漆着力太差﹐膜厚过厚﹐油漆未充分烤干造成油漆剥离素材的现象P09 凹痕﹕由于烤漆素材表面有下陷不平﹐造成烤漆后表面有下凹的痕迹的现象P10 凸点﹕由于烤漆素材表面有凸包﹐造成烤漆后表面有上凸的现象P11 磨痕:素材表面被打磨过所留下的长度及宽度相对大於其深度之表面缺失P12 桔皮﹕由于油漆流平性不佳﹐或涂装过厚使烤漆面形成类似于桔子皮的现象P13 膜厚超规格﹕烤漆层厚度超出QII 所规定的范围P14 色差﹕烤漆的颜色超出SPC﹐与标准色板比对存在明显颜色差异P15 酒精擦拭NG﹕使用98%以上纯度无水乙醇和棉布﹐1kgf 的力在烤漆表面来回擦拭20~50 次后,目视烤漆面有明显变化﹐或油漆有迁移到棉布上的现象P16 百格测试NG﹕用百格刀在烤漆表面划出见底材的1mm*1mm*100 格﹐用3M胶带紧紧粘住百格区域1 分钟﹐将胶带撕去﹐用4 倍的放大镜观察百格区域﹐脱漆面积大于总面积的5%的现象P17 冲击测试NG﹕使用检验文件所规定的冲头直径和重锤下落高度﹐对烤漆件进行正冲和反冲后﹐烤漆件出现漆层剥落或龟裂的现象P18 表面发黑/发黄:产品前处理后表面镀层颜色出现偏黑/偏黄的现象P19 皮膜发白:前处理后产品表面有白灰,或是表面镀层颜色与正常产品相比偏白的现象P20 水渍: 前处理后在产品表面形状不规则的白色或暗色部份P21 包装不良﹕产品的包装方式未完全按照相应的作业文件来执行,可能会造成品质隐患的现象P22 混料﹕两种或两种以上的产品同时放置在某单一产品所存放的区域P23 咬花不良﹕咬花形状与规格不符﹐或咬花表面分布不均匀的现象P24 油点﹕烤漆面存在类似于油渍点状的现象P25 针孔﹕由于油漆粘度或烤漆炉温过高﹐使产品在烤漆过程中形成气泡破裂﹐在烤漆表面呈现针孔状的现象P26 异色点﹕烤漆表面存在不同于烤漆本体颜色的色点P27 残漆粉﹕由于作业不良导致的在产品非喷漆区域出现油漆的不良现象P28 光泽过高/过低:喷漆产品光泽度测试超出或低于标准?5.2.3 组装不良项目定义A01 少件﹕组装后产品零部件个数少于文件规定所应有个数A01 多件﹕组装后产品零部件个数多于文件规定所应有个数。

不良描述中英文对照（范文模版）第一篇：不良描述中英文对照（范文模版）不良描述中英文对照(五金,塑料,PCB)1.Plastic parts塑膠部件-Inspection Points /檢查要點 :Abrasion/划痕,Bubbles/气泡, Burrs/毛刺,Bad Plating/電鍍不良, Contamination/雜質, Crack/爆裂,Combine Lines/結合線, Deformation/變形, Flow Marks/流痕, Greasy Dirt/油污, Haze/霧狀, Jelly/泠膠,Mold Marks/模痕,2.Metal Parts五金部件Inspection Points /檢查要點 :Abrasion/划痕 ,Bad Weld/焊接不良, Burrs/毛刺,Bad Plating/電鍍不良, Bend angle/折彎角度, Contamination/雜質, Crack/爆裂,Deformation/變形, Dents/凹痕,Greasy Dirt/油污, Mold Marks/模痕,Melange Color/混色, Oppilation Hole/盲孔, Pull White/拉白,Pour Hole uneven/澆口不平, Wrong Stamping/字麥不符,Short Shots/缺料, Shrinkage/縮水,Stripped Screw/螺絲滑牙, Top White/頂白, Weld Lines/夾水紋,Wrong Dimension/尺寸不符 , Wrong Texture/紋理錯誤, Light/發亮;-质量-Missing Stamp/漏沖壓, Oppilation Hole/盲孔, Pressing Marks/壓痕 , Rust/生鏽 ,Wrong Stamping/字麥錯誤 , Short Shots/缺料 ,Stripped Screw/螺絲滑牙,Pits/疤痕 , Specks/斑點Wrong Texture/紋理錯誤 ,Wrong Dimension/尺寸不符;bb3.Painting parts / SilkScreen parts 噴油/絲印部件 Inspection Points /檢查要點:Pooring Paint/薄油,Bleeding/滲色,Silkscreen Haze/絲印模糊,Bad Painting/噴油不良,Silkscreen Stamping Inconsistency/絲印字Contamination/雜質,樣不一致,deviate position/偏位, Scratch/划傷,Flow Marks/流痕,Speck/斑點 ,Missing paint/漏噴, Uneven Surface Oil/表面油層不均勻 ,Over Paint/肥油 ,Words Break Off/字体斷開 ,Pits/疤痕 ,Wrong Color/錯誤顏色,Poor Adhesion/附著力差,Wrong Texture/紋理錯誤;-PrintWords Leans/印刷字體傾斜 ,4.PCB 印制线路板 Open/开路;Short/短路;Weave Texture/板料席纹;Foreign Residue/外来杂物;Delamination/爆板,分层;Dent/凹陷;Dent on G/F/金手指凹陷;Scratch/擦花;Misregistration/对位不正;Board Damage/板子损坏;C/M Illegible/白字不清;C/M on pad/白字上垫;Copper expoure/露铜;Solder Mask on Pad/绿油上垫;Uneven Solder Mask/绿油不平均;Solder Mask peeling off/绿油脱落;Missing Hole/漏孔;5.Electronicparts 电子元件No AVL/没AVL;not on AVL/不在AVL上;Mfg/Mfg P/N dis-match AVL/ 与AVL不符;D/C overdue/ D/C 过期;无D/C;wrong part/错料;no reel/无卷轴;bulk packing for chip/ 散装;No dry packing(HIC change color)/ 无真空包装(防潮卡变色);No ESD packing/无防静电包装;illegible marking/印字不清,wrong marking/印字错;deformation/变型;micro crack/裂料;damaged part/ 烂料;Lead bent(PTH/SMT)/脚弯;Solder balls damaged/锡球坏wrong lead form/脚型错;wrong pitch/脚距不符;coplanar problem/平整度不良;Excess Hole/多孔;Wrong Hole Size/孔径错误;Hole Breakout/崩孔;Nick Trace/线路缺口;Void on Trace/线路铜穿;Diskdown/线路不良/狗牙;Solder Mask inside hole/绿油入孔;Discolouration under Solder Mask/绿油颜色不良;Foreign matter under Solder Mask/绿油下杂物;Solder Mask skipping/不过油;Solder on Gold Finger/金手指上锡;Poor Bevelling/斜边不良;Gold Finger burrs/金手指损坏;Ping Ring/粉红圈.pad(lead)oxidization/锡垫(引脚)氧化;wrong direction in tape(tray)/带中(盘中)方向错;short pins/引脚短;failed in solderability/ 焊锡不良;size(dimensions)out of specification/ 尺寸超标;function fail/ 功能不良;no tolerance/无误差范围;contamination/杂质;wrong identification for pin1/ 第1脚标识错.Broker Buy/炒料;(巻装物料)巻带前无空余巻带No blank cover tape for feeder loading巻带粘力不足Not enough adhesive for the cover tape.料盤变形Reel Deforming/卷带变型.第二篇：中英文对照A《美国口语惯用法例句集粹》ＡA(Page 1-4)1.about1)2)3)4)5)6)7)I'd like to know what this is all about.我想知道这到底是怎么回事。

Sewing/Textile Product - 缝制品／纺织品bag flap袋盖handle手挽buckle扣clip夹子snap劈啪扣clothes布料drawn string拉绳embroidery刺绣fabric织料hem包边，摺皱key holder锁匙扣lining内衬trap stitches埋线magic sticher魔术贴metal rivet铆钉pocket门袋pocket flap门袋盖rim车边seam缝sew-in label缝内标牌sewing line止口处车线shoulder strap背带strap带zip tie拉链吊尾zipper拉链zipper end拉链尾端zipper head拉链头zipper teeth拉链齿eyelet金属圈／孔眼／透气孔sweat strap(cap)汗带（帽）tail belt(cap)尾带（帽）tail belt buckle(cap)尾带扣（帽）top button(cap)顶珠（帽）visor(cap)帽舌harsh handfeel from dyeing染色不良造成手工粗糙foreign fiber混毛burn out烧焦poor embroidery刺绣不良insufficient stitcher per inch alonghems缝线针脚不够每英寸沿着摺边sewing label incrrect or missing布标固定不良或缺失holes or needle chew scar onsurface表面有碎针孔zipper no function or functionintermittent拉链无功能或功能间歇stitches not straight/wavystitching缝线不直zip sewed in reverse order拉链车反puckered起皱seam open爆口skip stitches跳针broken needle段针back stitches回针broken stitches断车线double/overlapped stitching重车loose stitching车线松missing stitches漏车线poor stitching车线不良stitches of different color thread缝线不同色insufficient stitches per inch along缝线不够密poor thread tension causingpucker缝线过紧引起起皱separation at seam where threadwas visible车缝开裂，缝线可见uneven borders边沿不平整poor trimming修正不良drawn yarn抽纱fabric broken布料烂holes on fabric布料有洞flaws on fabric布料有瑕疵tears on fabric布料破处fabric frayed布料磨损uneven/loose weaving of fabric布料编织不匀称tough to the touch due toexcessive dye染料过多，手感粗糙coarse yarn粗纱needle scar针痕poor hemming包边不良uneven hems包边不平thread color mismatched to fabric线与布料的颜色不搭配care label missing缺说明标签missing promotionaladvertisement paper (if缺广告宣传纸（如果可用）slide snap button no function orfunction intermittent滑动按扣无功能或功能间歇uneven or pulled loops (uncutterry)毛圈不均匀（针对不须切除的毛圈）missing label缺商标dye streaks within fabric布染色条痕slubs on frbric布上有粗结crocking of color磨擦褪色uncut loops (cut terry)毛圈未切除（对需要切的毛圈）General - 家具通用door门drawer抽屉floor地板mirror镜子peg木栓seat cushion座垫rack贮物／冒架shelf架子wood divide分隔木板wood slat木条solid wood实心木plywood / veneer board胶合板vanity带镜的梳妆台staples小钉子rivet铆钉arm rest扶手back rest后靠背castor脚轮gross beam横梁hinge铰链joint / tenon榫头mortise榫眼support stem支柱knot木结back panel后面板side panel侧面板steel seat plate铁座板toe kick脚后座gas lift气动升降装置height adjustable arm高度调节臂ladder梯／梯状物moisture content test湿度测试Wood Product - 木制品bug holes / rodent infestation蛀虫眼moisture content out of limit湿度含量超标bloating发涨poor or missing lacquering喷漆不良／木喷漆Wood Toilet Seat - 木厕座rust or excessive grease on metalcomponents and hardware金属部件生锈或有多余油脂hinges function not smooth铰链滑动不顺rust or poor plating on hinges,rivets or other materials铰链，铆钉或其它金属部件生锈或电镀不良gap between lid seat after closed盖，座间有缝隙（盖下盖后）missing mounting hardware缺装备部件hinges, knobs, bolts, nuts missingor not fit properly铰链，旋钮，门闩，螺帽缺，或不合适Ｔtools list - 工具列表large slotted screw driver大一字螺丝刀cross screw driver十字螺丝刀small slotted screw driver小一字螺丝刀razor剃刀medium knife中型刀small knife小型刀fish scaler刮鳞刀nail file指甲锉can opener开罐器pliers钳子ceramic stoneware - 陶瓷制品dirt / hair / trash embedded inglaze瓷层内有赃物／毛发／费品sharp points/edge锋利的尖端／锐边non-smooth welds焊接处不光滑excessive visible polishing lines过多的可见抛光纹weld marks a weld points焊接点有焊痕poor finishing at welds焊接表面处理不良rusty spots锈斑weld spark wire residue焊接火星残渣polishing compound residueespecially under the rim and rivets抛光混合物残渣（特别在镶边和铆钉处）unsecured rivets铆钉不牢misalign seam or joint接合处未对齐／对准improper alignment of handles手柄未对齐／对准improper fit of insert pieces to theset一套内置各件大小不合适leakage through the rivets铆钉处渗漏non-stick film thickness exceeded+/-5%不黏膜厚度不符 +/-5%irregullar or rough coating表面涂层粗糙不规则improper or unsecure bonding ofbase底座黏合不适／不牢unsecured fastening未系牢lids fit badly盖子大小不适overburn过烧overlapped重叠poor decal贴花不良poor glazing上釉不良crimping of curves not smooth褶线不平滑individual pieces of sets notmatching in pattern and color每套的单件产品之间图案／颜色不一致design not consistent in pattern ,size and color within and between每套产品的样式，尺寸及颜色设计不一致brass components tarnished (ifapplicable)铜制部件（若有）失去光泽finish not even and with bubblesor flaws抛光不平整，有气泡或瑕疵decorative patterns not consistentincluding color, size andplacement of design修饰图案不一致，包括颜色，尺寸及图案位置decals breakage釉面破裂decals incorrect color花釉颜色错误decals-broken, fizzle, scratch,mis-print花釉有破损，粘花微弱，刮伤，印错decals off position花釉移位／错位pin holes on the item产品上有针孔missinng items缺件missing glaze未上釉glaze not even and with bubblesor flaws釉面不平整，有气泡，瑕疵uneven painting喷涂不均匀damage no the ceramic瓷表面有破损handle not secured in place把手位置不适当unit bottom not polished产品底部未抛光pitted surface, depression onsurface表面有麻点，凹陷thickness of stoneware not eventhroughout the item瓷制产品厚度不均black spots黑斑decal贴花glazing上釉ignition button点火按钮lighter holder打火机固定器Ashtray - 烟灰缸cigarette slot deformed烟槽变形decal off center花釉偏离中心位置unglazed未上釉missing or incomplete decal缺花釉或花釉不全Cutlery - 刀具dinnerware - 餐具dinnerware list餐具列表ceramic dinnerware (pls.refer toceramic product)瓷制餐具（请参考瓷制品缺陷）stainless steel dinnerware不锈钢餐具cookware - 炊具kettle水煲coffee maker咖啡机electrical cookware电炊具Masher/Garlic press - 捣碎器plastic parts do not match intexture or gloss or color塑料部件的文理／光泽／颜色不一致welding lines焊接痕spot weld marks not properlycleaned or polished焊点不整洁／表面处理不良poor fitting of parts , especiallyon the handle and spout部件装配不良，尤其在把手及出口处rusty or corrosive rivets铆钉生锈／已腐蚀handle attachment not in-line withspout手柄和出口不在一条线上rotating handle not rotatedsmoothly手柄旋转不顺畅rotating handle placed in itsupright position not remain手柄不能保持直立Dehumidifier - 干燥器／除湿pre-filter damaged/deformed预滤器（粗滤器）损坏／变形foreign material inside cabinet内有异物poor fitness of water tank水箱大小不合适poor fitness of water hose水龙带大小不合适abnormal noise during operation操作时不正常噪音motor/condenser no function电机／冷凝器无功能indicating lamp no function指示灯无功能Hi-pot test failed高压不过polarity reversed极性接反fuse no function保险丝无功能ground wire discontinuous接地线中断temperature sensing cutoff testfailed温度感应断电测试失败no dehumidifier function无除湿功能live and neutral wires shortage incircuit火线和中线短路tensile pull test for carryinghandle failed把手张力测试失败gap between two halves of theplastic housing塑料机架两半有缝隙brass wire in power cord exposed电源线铜丝外露water full sensing cutoff testfailed水箱满水断电测试失败water tank sensor no function水箱感应器无功能barbecue tools - 烧烤用具lifting pump提升管inlet入水管spout出水管lock nut螺母housing外壳handle手柄poor laser printing激光打印不良deformed of water spouting出水口变形loose thread螺纹松water leakage漏水failure of the thread test螺纹测试失败failure of the pressure test耐压测试失败handle assembled not in properposition手柄位置安装不当missing sensormatic tag缺防盗标split of water spouting出水偏３failure of the leakage test渗漏测试失败shower head/hand shower - 花office chair - 办公椅caster轮脚arm rest扶手back rest靠背gas lift气棒seat cushion坐垫back support后背支架adjustive handle调节手柄butterfly plate蝴蝶盘leg脚fabric布leather皮stationery - 办公文具caculator计算器ball pen圆珠笔pencil铅笔refill笔芯nib笔头pen holder笔杆pen rack笔架pen cap笔帽pen container笔筒barrel笔身loop hole插笔孔ruler尺stencil镂空尺scissors剪刀cutter裁纸刀tape胶纸tape holder胶纸座glue胶水rubber橡皮擦pencil sharper铅笔消eraser板擦punch打孔机stapler钉书机ridge holderinner sheet内页cover封面memo pad便笺本paper clip纸夹clip board书写板copy holderwhite board白板letter pad信纸本printed film印刷薄膜CE sticker CE标签button closure关闭钮helmet头盔2# HB yellow pencil - 2#HB 黄铅笔burr or scratch on rubber wing橡皮边翼有刮伤和毛刺color of pencil not pantone 123c铅笔颜色对不上色卡号123Cpoor assembly between twohalves of wood / gap found on木头两半装配不良／铅笔顶端有缝隙graphite center in the wood木头中有石墨missing silkscreen of logo缺丝印标识rubber head assembled in theother end橡皮头装错头paint removed掉漆pin hole on body笔身有针孔wrong logo / name plate mixed inshipment同一船货的标识错误／名称图板相混eraser leaving marks like a red orpink crayon橡皮擦过后留有粉（红）色粉笔似印记pencil lead loose铅笔芯松lead broken铅笔芯断missing core缺铅笔芯Ball Point Pen -圆珠笔obvious shrinkage or deformationon the surface of plastic or metal塑料或金属部件表面有明显的萎缩或变形gap between two halves of theplastic housing塑料笔筒两半之间有缝隙difficult to assemble (ifapplicable)组装困难（若需组装）incorrect instruction / missinginstruction说明书错误／缺失metal and / or mechanical partsrusted金属及／或机械部件生锈pan cap unfit pen body笔帽不配笔身ink not fully filledinterpage corner rolled页卷角line not straight线不直insufficient page页数不够identification lines illegible标识线模糊不清inner sheet torn内页撕裂sheets edge not smooth页边缘不光滑／齐整handle loose out把手松incorrect material composition材料合成不对cannot fit standard size binders不配标准尺寸的活页封cannot open and close smoothly开关不顺／不灵活lock operation not smooth锁功能不顺inner sheet loosened out内页松垮／掉落inner sheet folded内页折叠impurities inside sheet纸内有赃物／杂物sheet surface not smooth页面不光滑Assorted 100 Count ClamshellBox - 哈壳式挖泥机盒blister edge broken吸塑边缘破裂holes on clamshell哈壳上有洞眼sharp edge on clamshell哈壳有锐边incorrect color assortment颜色组合不对excessive gap between cover andbase盖，座间间隙过大steel oxidized钢被氧化Imitation Jewellery - 仿真珠宝necklace项链bracelet手镯brooch胸针beads珠子flat sided beads平边珠子stone石头pearl珍珠pendant坠子snake chain蛇形链ear clip耳夹clasp扣子hook clasp钩扣knot结brooch pin胸针别针link环rubber stop橡皮塞set unevenly not flush to eachother（珠子等）设置不均匀，不整齐resin from... in plating…树脂从...流到…solid bubble in plating电镀表面有固体泡泡porosity on areas of plating电镀区域多孔clasp not open or close properly钩扣开关不顺clasp shift钩扣僵硬不灵blackened surface caused bysolder process焊接过程中造成表面黑话beads not matching in color珠子颜色不匹配beads slided over the knots andhit the next bead珠子滑过接头撞到下一个beads too loosely knotted珠子间间隔太松shading within the beads珠子表面有阴影pin not sharp enough别针不够锋利Clear/colored PlasticBeverageware - 透明／彩色饮料瓶caps/lids帽／盖bases座inner and outer shells内壳／外壳handles手柄thickwalls厚壁bubbles泡泡bubbles grouped in one area泡泡集中在一个区域bubble on lip area嘴唇区域有气泡burned mark烧痕blush脸红carbon spots碳斑carbon spots grouped in one area碳斑集中在一个区域carbob spots on light area碳斑在光亮区域carbon spots on lip area嘴唇区域有碳斑cloudy appearance云彩效果distorted歪曲color streaks/swirls彩色斑纹／旋斑cracking/chipped破裂／有缺口visible dragmark可见的拖痕flow lines on lip area流动线在嘴唇区域flash闪烁sprues注料口oily film油膜orange peel橙色皮orange peel on lip area橙色皮在嘴唇区域yellow tint黄色调warpage战争页Glassware - 玻璃器具glaze not even with bubble orflaws上釉不均，有气泡或瑕疵missing glaze未上釉item did not sitflush(wobbleing/rocking)产品站立不稳（摇晃）decal off position贴花釉位置不对glass shade玻璃灯罩Outdoor articles - 户外用品sleeping bag睡袋Paper Product - 纸制品cover page or inner sheets poorlyglued封面和内页粘贴不良page corner rolled页角卷边flash inside punched holescolor shading difference ondifferent sheets不同页上有不同的彩色阴影line not straight线不直insufficient pages页数不够identification line illegible标识线模糊不清inner sheet torn内页撕裂extra glue residue on sheetsurface表面残留胶水太多inner sheets loosened out内页松垮／掉落wrinkled mark on sheet surface页表面有皱痕distance between lines notidentical行距不一致inner sheet folded内页有摺皱blurred ink mark模糊的墨水印impurities inside sheet纸内有杂斑UPC printed on cover pagescratched封面上的条码有刮伤sheet surface not smooth纸表面不光滑no watermark无水印sheets poorly heat-sealed热收缩密封不良sharp point or sharp edge (injuryto the user)锋利的点或边（会伤害用户）paper chipped纸缺口wrinkled on paper/paper box有皱纹fold line on paper/paperbox/playing card有摺皱pattern on back not consistent(playing card)背面图案组成不对（扑克牌）missing ornaments ontree/poinsettia树／猩猩木上缺装饰物foreign particles inside the base底座内有异物brass wire in power cord exposed电源线铜丝外露motor cannot rotate马达不转abnormal noise in music box (ifapplicable)音乐盒（若有）有异常噪音light cannot extend to fiber opticend灯不能照及光纤末端conduction wires inside thehousing too loose or wire poorly机座内导线过松或整理不良melody/rhythm incorrect旋律／节奏不对bulb broken灯泡破transformer no output变压器无输出功能motor movement too loose马达机芯过松Headset/Earphone - 耳机／听excessive noise噪音过大microphone adjusting arm麦克风调节臂mute button静音钮switch/control开关／控制键bottom foot底角blister broken吸塑破Candle - 蜡烛wax蜡flame火焰peppermint薄荷油wick灯芯scent香味white snowflake like spots点状白色雪片frost mark on surface表面有霜状痕迹caved in on one side一边凹焰wick smoked excessively灯芯冒烟严重flame was small and died out火焰小，逐渐熄灭unscented无香味air bubbles on surface表面有气泡cracked inside内部裂flame burned a tunnel火焰中间烧出一条道wick drowned in melted wax灯芯浸入熔化蜡中wax left on the insides ofcontainer容器内粘有蜡Mini blinds - 百叶窗double slats双重窗叶light leakage漏光gap between slats too large窗叶间缝隙太大lock function intermittent锁不住basket ball/foot ball/volleyball/tennis ball - 篮球／足球／排球／网球too much air inside the ball (toohard)气过足ball does not inflate properly充气不良damage no the item/nap no tidy表面绒毛不整齐gift box did not stand in verticalmanner礼篮不能垂直站立not enough air inside the ball (toosoft)气不足bouncing height too low/too high球弹高度过底／过高hole in rubber橡皮上有洞poor stitching缝制不良。

1〉Abrasion: A surface imperfection that removes or displacesmaterial characterized by its large width and lengthrelative to its depth.中譯：擦破/磨損一個表面的瑕疵.移動材料時造成較大的寬度、長度、深度之特徵。

2>Bleeding：This defect is the discoloration created by the diffusionof coloring material through an applied coating fromthe substrate to the surface of the coating。

中譯：滲出染料擴散,自底層到表層，造成表面上的瑕疵。

3＞Blemish：The change in the surface appearance due to a flaw orcosmetic defect.中譯: 污損/污點因為一個瑕疵或外觀不良而改變表面外部4＞Blister：The raised bumps in the surface, caused by air orsolvent vapors forming within or under the coating。

中譯: 水泡由於來自烤漆內部或表面的空氣或溶劑氣體造成表面隆起突出。

5＞Blush：Discoloration or change in gloss, generallyappearing at the gates, abrupt thicknesschanges or other structures along flow pat。

中譯：異色通常發生在射出進料口、肉厚突然縮減、或流道交錯之處6＞Bubble： A gas pocket in a plastic molded part. For a coating, it isthe same as blister。

1>Abrasion: A surface imperfection that removes ordisplaces material characterized by its largewidth and length relative to its depth.中译: 擦破/磨损一个表面的瑕疵。

移动材料时造成较大的宽度、长度、深度之特徵。

2>Bleeding: This defect is the discoloration created by thediffusion of coloring material through anapplied coating from the substrate to thesurface of the coating.中译: 渗出染料扩散，自底层到表层，造成表面上的瑕疵。

3＞Blemish: The change in the surface appearance due to aflaw or cosmetic defect.中译: 污损/污点因为一个瑕疵或外观不良而改变表面外部4＞Blister: The raised bumps in the surface, caused by airor solvent vapors forming within or under thecoating.中译: 水泡由於来自烤漆内部或表面的空气或溶剂气体造成表面隆起突出。

5＞Blush: Discoloration or change in gloss, generally appearing at the gates, abrupt thicknesschanges or other structures along flow pat.中译: 异色通常发生在射出进料口、肉厚突然缩减、或流道交错之处6＞Bubble: A gas pocket in a plastic molded part. For acoating, it is the same as blister.中译: 气泡一个气体包覆(中空)在塑胶件上，对烤漆来说，与blister意义相同7＞Burn Mark: A condition where supper-heated trapped air inthe cavity heats or burns the surface of theplastic part.中译: 焦痕8＞Burr:This defect appears as a rough or sharp edgeon metal after it has been cast, cut, drilled,stamped, and so forth. Burrs will usually snagor tear a cleaning cloth.中译: 毛边(头) 在材料经过铸造、切割、钻孔、冲压等等外观形成一个粗糙或锐利边缘，毛边总是会刺穿或扯裂整齐的衣物。

1>Abrasion: A surface imperfection that removes ordisplaces material characterized by itslarge width and length relative to itsdepth.中译: 擦破/磨损一个表面的瑕疵。

移动材料时造成较大的宽度、长度、深度之特徵。

2>Bleeding: This defect is the discoloration created bythe diffusion of coloring material throughan applied coating from the substrate to thesurface of the coating.中译: 渗出染料扩散，自底层到表层，造成表面上的瑕疵。

3＞Blemish: The change in the surface appearance due toa flaw or cosmetic defect.中译: 污损/污点因为一个瑕疵或外观不良而改变表面外部4＞Blister: The raised bumps in the surface, caused byair or solvent vapors forming within orunder the coating.中译: 水泡由於来自烤漆内部或表面的空气或溶剂气体造成表面隆起突出。

5＞Blush: Discoloration or change in gloss, generallyappearing at the gates, abrupt thickness changes or other structures along flow pat.中译: 异色通常发生在射出进料口、肉厚突然缩减、或流道交错之处6＞Bubble: A gas pocket in a plastic molded part. Fora coating, it is the same as blister.中译: 气泡一个气体包覆(中空)在塑胶件上，对烤漆来说，与blister意义相同7＞Burn Mark: A condition where supper-heated trapped airin the cavity heats or burns the surface ofthe plastic part.中译: 焦痕8＞Burr:This defect appears as a rough or sharp edgeon metal after it has been cast, cut,drilled, stamped, and so forth. Burrs willusually snag or tear a cleaning cloth.中译: 毛边(头) 在材料经过铸造、切割、钻孔、冲压等等外观形成一个粗糙或锐利边缘，毛边总是会刺穿或扯裂整齐的衣物。

1>Abrasion: A surface imperfection that removes ordisplaces material characterized by its largewidth and length relative to its depth.中译: 擦破/磨损一个表面的瑕疵。

移动材料时造成较大的宽度、长度、深度之特徵。

2>Bleeding: This defect is the discoloration created by thediffusion of coloring material through anapplied coating from the substrate to thesurface of the coating.中译: 渗出染料扩散，自底层到表层，造成表面上的瑕疵。

3＞Blemish: The change in the surface appearance due to aflaw or cosmetic defect.中译: 污损/污点因为一个瑕疵或外观不良而改变表面外部4＞Blister: The raised bumps in the surface, caused by airor solvent vapors forming within or under thecoating.中译: 水泡由於来自烤漆内部或表面的空气或溶剂气体造成表面隆起突出。

5＞Blush: Discoloration or change in gloss, generally appearing at the gates, abrupt thicknesschanges or other structures along flow pat.中译: 异色通常发生在射出进料口、肉厚突然缩减、或流道交错之处6＞Bubble: A gas pocket in a plastic molded part. For acoating, it is the same as blister.中译: 气泡一个气体包覆(中空)在塑胶件上，对烤漆来说，与blister意义相同7＞Burn Mark: A condition where supper-heated trapped air inthe cavity heats or burns the surface of theplastic part.中译: 焦痕8＞Burr:This defect appears as a rough or sharp edge onmetal after it has been cast, cut, drilled,stamped, and so forth. Burrs will usually snagor tear a cleaning cloth.中译: 毛边(头) 在材料经过铸造、切割、钻孔、冲压等等外观形成一个粗糙或锐利边缘，毛边总是会刺穿或扯裂整齐的衣物。

布料填充玩具不合格品之缺陷分類:按照國際標準,缺陷被分為三類:極嚴重(CRITICAL)/嚴重(MAJOR)/輕微(MINOR)極嚴重缺點-----不能符合安全標準或者不良現象促使産品完全失去功能及特殊限定 之缺點為客戶無法接受之缺點,稱之為極嚴重缺點嚴重缺點------不良現象促使産品失去主要的功能或功能誤差及嚴重的外觀缺點,稱 之為主要缺點輕微缺點------不影響産品功能的外觀缺點,稱之為次要缺點*根據不同的系列將會用不同的AQL 及不同的測試標準品管部工作指引版本：01不合格品鑒定標准布料/毛絨公仔版本：01布料/毛絨公仔版本：01版本：01包裝-外箱/彩盒不合格品鑒定標准不合格品之缺陷分類:按照國際標準,缺陷被分為三類:極嚴重(CRITICAL)/嚴重(MAJOR)/輕微(MINOR)極嚴重缺點-----不能符合安全標準或者不良現象促使産品完全失去功能及特殊限定之缺點為客戶無法接受之缺點,稱之為極嚴重缺點嚴重缺點------不良現象促使産品失去主要的功能或功能誤差及嚴重的外觀缺點,稱之為主要缺點輕微缺點------不影響産品功能的外觀缺點,稱之為次要缺點*根據不同的系列將會用不同的AQL及不同的測試標準品管部工作指引合金/塑膠不合格品之缺陷分類:按照國際標準,缺陷被分為三類:極嚴重(CRITICAL)/嚴重(MAJOR)/輕微(MINOR)極嚴重缺點-----不能符合安全標準或者不良現象促使産品完全失去功能及特殊限定 之缺點為客戶無法接受之缺點,稱之為極嚴重缺點嚴重缺點------不良現象促使産品失去主要的功能或功能誤差及嚴重的外觀缺點,稱 之為主要缺點輕微缺點------不影響産品功能的外觀缺點,稱之為次要缺點*根據不同的系列將會用不同的AQL 及不同的測試標準合金/塑膠産品版本：01不合格品鑒定標准品管部工作指引版本：01合金/塑膠産品品管部工作指引版本：01。

和深度相對於寬度長,下的留件表面零刮傷﹕受尖銳硬物划踫而在S01度較長的線狀痕跡S02 毛刺﹕產品沖裁后留在零件剪切邊的批鋒S03 模痕﹕模具在成形零件過程中造成的均勻類似刮痕現象S04 壓傷﹕由于模具表面有異物﹐使產品在沖壓成形過程中受壓力作用在表面留下塊狀的下凹的現象S05 切邊不齊﹕產品沖裁后零件剪切邊呈現出不整齊的現象S06 晃動:由于產品平面度超出spec﹐而呈現出凹凸不平的現象S07 尺寸超差﹕產品的尺寸超出SpecS08 材料外觀不良﹕原材料本身就具有的一些如白斑﹐黑點 ,麻點﹐發黑﹐白灰﹐刮傷﹐氧化等方面的不良S09 抽牙不良﹕抽牙尺寸超出Spec﹐或是出現抽牙抽歪﹐抽牙抽裂的現象S10 攻牙不良﹕攻牙孔攻歪﹐通規不通﹐止規不止﹐或是出現實配螺絲打不進, 實配螺絲滑牙的現象S11 鉚合不良﹕鐵件鉚合后﹐鐵件與鐵件間間隙超Spec﹐或鉚合孔偏位﹐鉚合不牢固之現象S12 凸包/拱橋沖裂﹕受模具﹐沖床壓力﹐或材料硬度的影響﹐產品在成形過程中凸包/拱橋表面產生明顯的裂紋﹐或完全開裂的現象S13 少工程﹕產品成形的工程數少于作業文件所規定的工程數的現象S14 變形﹕由于受外力作用﹐產品失去其本身所應具有的形狀的現象S15 生鏽﹕基體材料表面或切邊呈現經色﹐發生化學氧化的現象S16 不潔﹕產品表面附著除油污﹐毛刺以外的其它異物S17 油污﹕粘附於零件表面能擦除的呈塊狀或膜狀的油脂或變色異物S18 碰刮傷﹕受尖銳硬物刮踫而在零件表面留下的﹐長度相對於寬度和深度較長的表面斑痕S19 包裝不良﹕產品的包裝方式未完全按照相應的作業文件來執行﹐可能會造成品質隱患的現象S20 混料﹕兩種或兩種以上的產品同時放置在某單一產品所存放的區域S21 點焊不良﹕產品點焊后鐵件與鐵件間連接不牢固﹐拉力測試超Spec.存在點焊點錯位﹐漏焊,虛焊,燒穿,焊渣等缺陷的現象S22 字模不清/殘缺/錯誤﹕Mark 字體不完整﹐模糊不清﹐字模的位置﹐式樣等未完全按作業文件要求作業的現象5.2.2 涂裝不良項目定義P01 雜質:由于烤漆面粘附有雜質﹐烤漆后在表面形成一種凸起的可剝落的塊狀或點狀漆的現象P02 刮傷/掉漆﹕烤漆表面在外力(碰撞﹐擦刮)作用下﹐漆層呈點狀﹐塊狀或成線狀(刮傷)破壞﹐可見或不可見底材的不良現象P03 凝漆﹕由于霧化不良或油漆未完全溶解造成在烤漆表面形成凸包狀漆塊的現象P04 發白﹕烤漆面受手指或包材碰擦﹐目視烤漆面有不同于烤漆本體顏色的白色痕跡P05 噴漆不良均勻﹕烤漆面油漆形成高低不平﹐或膜厚不一致的現象P06 少噴漆﹕產品的烤漆區域少于作業文件所規定的烤漆區域﹐或烤漆的膜厚太低﹐未達到所規定的標准P07 溢漆﹕烤漆時油漆霧化到非烤漆區域的現象P08 漆層剝落﹕由于油漆著力太差﹐膜厚過厚﹐油漆未充分烤干造成油漆剝離素材的現象P09 凹痕﹕由于烤漆素材表面有下陷不平﹐造成烤漆后表面有下凹的痕跡的現象P10 凸點﹕由于烤漆素材表面有凸包﹐造成烤漆后表面有上凸的現象P11 磨痕:素材表面被打磨過所留下的長度及寬度相對大於其深度之表面缺失P12 桔皮﹕由于油漆流平性不佳﹐或涂裝過厚使烤漆面形成類似于桔子皮的現象P13 膜厚超規格﹕烤漆層厚度超出QII 所規定的范圍P14 色差﹕烤漆的顏色超出SPC﹐與標准色板比對存在明顯顏色差異P15 酒精擦拭NG﹕使用98%以上純度無水乙醇和棉布﹐1kgf 的力在烤漆表面來回擦拭20~50 次后,目視烤漆面有明顯變化﹐或油漆有遷移到棉布上的現象P16 百格測試NG﹕用百格刀在烤漆表面划出見底材的1mm*1mm*100格﹐用3M膠帶緊緊粘住百格區域1 分鐘﹐將膠帶撕去﹐用4 倍的放大鏡觀察百格區域﹐脫漆面積大于總面積的5%的現象P17 沖擊測試NG﹕使用檢驗文件所規定的沖頭直徑和重錘下落高度﹐對烤漆件進行正沖和反沖后﹐烤漆件出現漆層剝落或龜裂的現象P18 表面發黑/發黃:產品前處理后表面鍍層顏色出現偏黑/偏黃的現象P19 皮膜發白:前處理后產品表面有白灰,或是表面鍍層顏色與正常產品相比偏白的現象規則的白色或暗色部份狀不后在產品表面形理前處: 水漬P20P21 包裝不良﹕產品的包裝方式未完全按照相應的作業文件來執行,可能會造成品質隱患的現象P22 混料﹕兩種或兩種以上的產品同時放置在某單一產品所存放的區域P23 咬花不良﹕咬花形狀與規格不符﹐或咬花表面分布不均勻的現象P24 油點﹕烤漆面存在類似于油漬點狀的現象P25 針孔﹕由于油漆粘度或烤漆爐溫過高﹐使產品在烤漆過程中形成氣泡破裂在烤漆表面呈現針孔狀的現象P26 異色點﹕烤漆表面存在不同于烤漆本體顏色的色點P27 殘漆粉﹕由于作業不良導致的在產品非噴漆區域出現油漆的不良現象P28 光澤過高/過低:噴漆產品光澤度測試超出或低于標准5.2.3 組裝不良項目定義A01 少件﹕組裝后產品零部件個數少于文件規定所應有個數A01 多件﹕組裝后產品零部件個數多于文件規定所應有個數。