伦茨变频器样本

伦茨（Lenze）变频器8200Vector系列使用说明注：本说明适用于梳棉机FA231A所使用 Lenze E82EV系列变频器包括内容:1.标准接线及安装1.1 ４００Ｖ控制器的主电源接线1.2 电机接线1.3符合ＥＭＣ标准的安装1.4控制端子接线及说明2. 用操作面板进行参数设定2.1访问,设定所有参数2.2拷贝参数到操作面板2.3从操作面板复制参数到变频器2.4 输出转速的在线调整--用操作面板输入频率(hz)与其他给定值相加3.重要参数代码说明3.1 C0014代码可设置控制模式3.2 电机数据的输入/自动检测(C0087;C0088;C0089;C0090;C0091;C0084;C0092;C0148)3.3 JOG固定频率给定值(C0037,C0038,C0039)3.4 给定值选择(C0001)3.5 模拟输入给定的调整(C0026;C0027)3.6 PTC电机温度监控(C0119)3.7 数字输入信号配置(C0007)3.8 最小输出频率(C0010)3.9 最大输出频率(C0011)3.10 主加速时间(C0012)3.11主减速时间(C0013)3.12快停减速时间(C0105)3.13数字输入信号E1-E6电平反相(C0114)3.14 模拟量输入范围设定（C0034）3.15电流极限设定（C0022,C0023）4.故障诊断及排除4.1运行状态显示4.2故障查询5. 梳棉机FA231A变频器参数设定表5.1 E82EV222S4B参数设定表5.2 E82EV751S4B参数设定表6.变频器调试程序表7.产品维护,保养要点1.标准接线及安装1.1 ４００Ｖ控制器的主电源接线1.2 电机接线见上图注:ＢＲ１，ＢＲ２外部制动电阻Ｔ１，Ｔ２1.3符合ＥＭＣ标准的安装使用低寄生电容电缆。

每单位长度电容值：●芯／芯≤７５ｐＦ／ｍ●芯／屏蔽层≤１５０ｐＦ／ｍＥＭＣ电缆密封垫按铭牌进行电机接线使用表面导电的安装板以尽可能大的导电表面将电缆屏蔽层连到ＰＥ上。

伦茨变频器参数如下Allen-Bradley PowerFlex 7-Series AC Drives, or drives that use a variable frequency drive (VFD), are designed to give optimized motor control for a wide range of applications. The main parameters that must be considered when specifying a PowerFlex 7-Series drive are the voltage rating, current rating, frequency of operation, number of phases, type of enclosure, control mode, and number of I/O.Voltage rating: The voltage rating of the PowerFlex 7-Series drive must be sufficient to allow it to control the motor in the application. Voltage ratings can range from 120 VAC to 690 VAC.Current rating: The current rating of the PowerFlex 7-Series drive must be capable of powering the motor in the application. Current ratings can range from 0.5 Amps to 1700 Amps.Frequency of operation: The frequency output of the PowerFlex 7-Series drive can be adjusted to match the motor’s operating frequency. The range is 1 Hz to 650 Hz.Number of phases: The PowerFlex 7-Series drive is available in single-phase, three-phase, and multi-phase configurations.Type of enclosure: The PowerFlex 7-Series drive is available in NEMA 1, NEMA 12, and IP66 enclosures.Control mode: The PowerFlex 7-Series drive can be operatedin either current or voltage mode.Number of I/O: The PowerFlex 7-Series drive is available with a variety of I/O options, including 0 to 24 analog inputs, 0 to 32 digital inputs, 0 to 16 analog outputs, and 0 to 32 digital outputs.The PowerFlex 7-Series AC Drives use a VFD to control the motor, providing smooth control of speed, torque, and power. The adjustable parameters of the PowerFlex 7-Series drive vary depending on the application and can be configured by the customer. Additionally, the PowerFlex 7-Series drive has built-in protection features, including over-voltage protection,under-voltage protection, over-current protection, ground fault protection, and short-circuit protection. The drives also offer motor fault diagnostics, allowing for quick troubleshooting of any motor issues. PowerFlex 7-Series drives are also backed by Allen-Bradley’s global network of service and support.。

伦茨变频器样本范文伦茨变频器的样本可以分为三个主要部分：输入电路、直流中间电路和输出电路。

输入电路用于将交流电源转换为直流电源，以便供给输出电路使用。

直流中间电路则用于储存和调节电能，以保证输出电路在工作过程中的稳定性。

输出电路则将直流电能转换为交流电能，通过变频控制电机的转速。

伦茨变频器的输入电路通常由整流器和滤波器组成。

整流器将交流电源转换为直流电源，并通过滤波器滤除电源中的噪声和谐波。

这可以保证变频器在供电过程中的稳定性和可靠性。

直流中间电路则由电容器和电阻器组成，用于储存电能并在需要时进行调节。

输出电路通常由逆变器、滤波器和电机组成。

逆变器将直流电能转换为交流电能，并通过滤波器滤除电流中的谐波和噪声。

通过变频控制，电机的转速可以根据实际需求进行调节。

伦茨变频器的样本不仅具有高效稳定的性能，还具有多种保护功能。

例如，过流保护可以在电流超过设定值时立即切断电源，以防止电机过载损坏。

过压和欠压保护可以在电压异常时自动切断电源，以保护设备的安全运行。

过载保护可以在负载过大时减少输出功率，以保护电机和变频器不受损坏。

伦茨变频器样本还具有智能化控制的特点。

通过集成微处理器和信号处理器，它可以实现多种运行模式和参数设置。

用户可以通过调节变频器的参数来实现不同的控制方式，如恒定转矩控制、矢量控制和速度闭环控制等。

这些功能使得变频器可以适应不同的工作环境和工艺要求，并且可以实现更精确的控制效果。

总之，伦茨变频器样本具有高效稳定的性能、多种保护功能和智能化控制的特点。

它是现代工业生产中不可或缺的设备，可以为生产过程提供高效的动力驱动和能源控制。

同时，伦茨变频器的样本也在不断发展和创新，以满足不同行业的需求，并助力工业生产实现更高水平的智能化和可持续发展。

Brochure | ENFrequency inverter 0.25 ... 132 kWLenze inverter – universally applicable.A multifunctional all-rounder applicable for all cases – just another way to perfectlydescribe the frequency inverter. Thanks to a high number of integrated functions,network interfaces and a simple parameter setting, the inverter is suitable for bothmechanical engineering and apparatus construction.Lenze inverters are an important component in modern drive solutions whichrange from the cloud via control systems to motors and geared motors.Typical application fields• Textile machines• Materials handling technology• Packaging technology• Forming technology• Consumer goods machines• Industrial air conditioning technology (pumps, fans & compressors)• Construction machines• Access control• etc.Features• The modular and scalable concept allows the selection of the inverter requiredfor the respective application.• The compact design allows an efficient installation for applications where spacemeans money.• Easy installation and OEM friendly as standard. Robust design for reducingcabling costs in large installations.• Interaction for each application level – from simple to complex!• Energy-efficient and high functionalityThe benefits for you• Lower investment costs• Less control cabinet space and costs• More productivity• More time for innovation• Sustainability• ReliabilityFeatures at a glance.A good usability of the devices ranging from installation to service reduces working time, costs and errors in handling. This makes installation with keyhole mounting and plug-in terminals particularly convenient.Programming your application is opti-mized for all application levels.The smartphone app via WLAN pro-vides only one of numerous interfaces to the device.User-friendlinessFlexibilityCompact designIn mechanical engineering andapparatus construction, space is limited and expensive. Thus, Lenze inverters are extremely compact to implement solutions and save costs.The i5.0 devices impress with a space-saving design with a width of 60 mm (up to 4.0 kW) and a depth of just 130 mm (up to 11 kW). Moreover, the devices can be be mounted directly next to each other without derating.Lenze offers one of the most com-prehensive solution portfolios formechanical engineering and apparatus construction.No matter which power, mains volt-ages, communication interfaces ordiagnostics options – our product range has the right solution optimized for the requirement.RobustnessIO-LinkCentralized/decentralizedMany machines and apparatus provide enough space for a compact inverter such as the i510 or i550.If your machine requires a lot of space, has a modular design or the space in the control cabinet is limited, we rec-ommend a decentralized installation close to the motor. This serves to avoid the installation costs of e.g. expensive motor cables.In many applications, a mixture of cen-tralized and decentralized drive tech-nology is advisable. Fortunately, the i5x0 cabinet and i5x0 protec inverters show the same drive behavior.For an intelligent integration ofsensors and actuators, IO-Link is used increasingly. If the system already con-tains an IO-Link master, inverters can be integrated cost-effectively. With the i550, Lenze is the first man-ufacturer to fulfil the IO-Link standard V1.1. This allows the inverter to be automatically parameterized for serial commissioning or in the event of service.Applications, for instance in the timber industry or intralogistics, place high demands on the components of the machines regarding robustness. Harsh environments are no problem for the i550 protec.Featuring the IP66 degree of protection (Indoor & Outdoor NEMA 4X), the tech-nology inside the housing is protected against dust and the device can be safely cleaned using water jets.i510 cabinet i550 cabineti550 protec8400 motec• Basic inverter IP20NEMA Open Type• 0.25 ... 11 kW• Standard inverter IP20• Universally applicable• 0.25 ... 110 kW• Standard inverter IP31 or IP66• Universally applicable• 0.37 ... 11 KW (expansion up to 75 kWplanned)• Standard inverter for motor orwall mounting IP65• Various connector options for power andsignals for minimum installation expenses• 0.37 ... 7.5 kW Configurablefor all requirements.Frequency inverterLenze offers a comprehensive inverter portfolio for mechanical engineering andapparatus construction. Whether control cabinet mounting, motor mounting ordecentralized mounting with terminals or with complete connection technology– our independent advice is geared towards finding the best solution for yourspecific case.The Lenze EASY Product Finder helps you configure your required frequencyinverter type in next to no time. In addition, you can retrieve all importanttechnical details such as data sheets, CAD data and EPLAN data.EASY Product Finderi510 and i550 cabineti510 and i550 cabinet form the inverter series for the control cabinet in a powerrange of 0.25 ... 132 kW. They are distinguished by the following attributes – slimdesign, scalable functionality and exceptionally user-friendly. The simple i510from 0.25 ... 11 kW and the universally applicable i550 from 0.25 ... 110 kW havethe same DNA but differ in functionality and are optimized for a good price/performance ratio.Highlights• Space saving design: 60 mm wide (up to 4 kW), 130 mm deep(up to 11 kW), with zero-clearance mounting• Innovative interaction options enable better set-up times than ever.• The wide-ranging modular system enables various product configurationsdepending on machine requirements• Optionally with "Safe Torque Off (STO)" with SIL 3 (ISO 13849-1 (EN 954-1) ) andPerformance Level e (EN 62061/EN 61800-5-2)• Flexibility: Get the i550 as a complete device or in individual components(Power Unit, Control Unit and Safety Unit)i510 cabineti550 cabinetPower range ·0.25 ... 110 kW Mounting ·Wall mounting ·InstallationDegree of protection ·IP20·NEMA Open Type ----Approvals·CE, UL, CSA, EAC, RoHS Connections ·1 AC 120 V ·1 AC 230 V ·1/3 AC 230 V ·3 AC 230 V·3 AC 400 V/480 V -·Standard I/O 5x digital input 1x digital output -·Application I/O:7x digital input 1x digital output PNP/NPN logic ·Standard I/O 2x analog input 1x analog output ·Application I/O: 2x analog input 2x analog output·Frequency input: 0 … 100 kHz·1x NO/NC relay (24 DC max. 2 A; 240 AC max. 3 A)·External 24 V supply and internal 24 V power supply unit -·Spring terminals, plug-in ·Evaluation of motor PTCOverload behavior·200 % for 3s; 150 % for 60s Motor controls·Servo control (SC-ASM) with feedback·Sensorless vector control for synchronous motors (up to 22 kW)·Sensorless vector control (SLVC)·Energy saving function (VFC-Eco)·V/f characteristic control linear/square-law (VFC plus)·V/f characteristic control with feedbackFunctions·DC-injection braking·Brake management for brake control with low rate of wear·Dynamic braking through brake resistor·S-ramps for smooth acceleration and deceleration ·Flying restart circuit, PID controller ·DC connection ·Safety engineering Safe Torque Off (STO)Networks·CANopen, Modbus RTU, Modbus TCP, IO-Link, EtherCAT,EtherNET/IP, PROFIBUS, PROFINET, POWERLINKAmbient temperature during operation·3K3 (-10 ... +55 °C) EN 60721-3-3 (derating of 2.5 %/°C above 45 °C)Power range ·0.25 ... 11 kW Mounting -·InstallationDegree of protection ·IP20·NEMA Open Type ----Approvals·CE, UL, CSA, EAC, RoHSConnections -·1 AC 230 V ·1/3 AC 230 V ·3 AC 230 V ·3 AC 400/480 V -·Basic I/O: 5x digital input 1x digital output -----·Basic I/O:2x analog input 1x analog output ---·no·1x NO/NC relay (24 DC max. 2 A; 240 AC max. 3 A)--·Spring terminals·Evaluation of motor PTCOverload behavior·200 % for 3 s; 150 % for 60 sMotor controls -·Sensorless vector control for synchronous motors (up to 22 kW)·Sensorless vector control (SLVC)·Energy saving function (VFC-Eco)·V/f characteristic control linear/square-law (VFC plus)-Functions·DC-injection braking·Brake management for brake control with low rate of wear -·S-ramps for smooth acceleration and deceleration ·Flying restart circuit, PID controller ·DC connection Safety engineering -Networks·CANopen, Modbus RTUAmbient temperature during operation·3K3 (-10 ... +55 °C) EN 60721-3-3 (derating of 2.5 %/°C above 45 °C)i550 proteci550 protec uses the same tried-and-tested technology used in i550 cabinet andonly differs in terms of a higher degree of housing protection with an adapteddesign. If your machine requires a lot of space, has a modular design or the spacein the control cabinet is limited, the universally applicable i550 protec (IP31and IP66 degree of protection) from 0.37 kW ... 11 kW (expansion up to 75 kWplanned) is the ideal solution for a decentralized installation close to the motor.Highlights• IP66 degree of protection (Indoor & Outdoor NEMA 4X) with protection againsthigh pressure water jets from any direction and dust tightness allows for use inharsh environment applications• USB Micro diagnostic interface on board• Optionally available with extension box with or without service switches• Optionally available with keypad or WLAN diagnostic module• Optionally available with "Safe Torque Off (STO)" with SIL 3 (ISO 13849-1(EN 954-1) ) and Performance Level e (EN 62061/EN 62061/EN 61800-5-2)i550 protecPower range·0.37 ... 11 kWMounting·Wall mounting·InstallationDegree of protection·IP31·NEMA 1·IP66·NEMA 4 x--Approvals·CE, UL, CSA, EAC, RoHSConnections·1 AC 120 V·1 AC 230 V·1/3 AC 230 V·3 AC 230 V·3 AC 400/480 V·3 AC 480 V/600 V·Standard I/O:5x digital input1x digital output----PNP/NPN logic·Standard I/O:2x analog input1x analog output---·Frequency input: 0 … 100 kHz·1x NO/NC relay (24 DC max. 2 A; 240 AC max. 3 A)·External 24 V supply andinternal 24 V power supply unit·Spring terminals·Evaluation of motor PTCOverload behavior·200 % for 3 s; 150 % for 60 sMotor controls·Servo control (SC-ASM) with feedback·Sensorless vector control for synchronous motors (up to 22 kW)·Sensorless vector control (SLVC)·Energy saving function (VFC-Eco)·V/f characteristic control linear/square-law (VFC plus)·V/f characteristic control with feedbackFunctions·DC-injection braking·Brake management for brake control with lowrate of wear·Dynamic braking through brake resistor·S-ramps for smooth acceleration and deceleration·Flying restart circuit, PID controller·DC connectionSafety engineering·Safe Torque Off (STO)Networks·CANopen, Modbus RTU, Modbus TCP, IO-Link, EtherCAT, EtherNET/IP, PROFINETAmbient temperature during operation·3K3 (-10 ... +55 °C) EN 60721-3-3 (derating of 2.5 %/°C above 45 °C)8400 motecThe 8400 motec is a frequency inverter for decentralized installation from0.37 ... 7.5 kW in IP65. In the three basic variants for motor mounting, wallmounting or wall mounting with service switch, it already offers a high degree offlexible solutions. Wherever the focus is on a safe and fast installation of drives, the8400 motec is the most beneficial solution, e.g. in spatially distributed applications.Motor mounting:In the case of motor mounting, the 8400 motec can be operated without deratingregardless of the alignment. Compact solution with Lenze MF motor (120 Hz).Wall mounting:Compact and flexible solution for wall mounting in IP65.Wall mounting with service switch:Wall-mounted device with 3 maintenance switches. Options for maximumflexibility in IP54.Highlights• Compact design• High degree of functionality, e.g. integrated brake rectifier• M12 signal connector for fieldbuses, IOs, external 24 V supply and STO• High variety of mains plugs for Harting Q4/2 (single or double),M15 or QUICKON QPD• Wall mounting without derating8400 motecPower range·0.25 ... 7.5 kWMounting·Wall mounting·Motor mountingDegree of protection·IP66·IP54 (with switching unit)----Approvals·CE, UL, CSA, EAC, RoHSConnections----·3 AC 400/480 V-·Standard I/O:5x digital input1x digital output1 inverter enable---PNP/NPN logic------·Frequency input: 0 … 10 kHz·1x NO/NC relay·External 24 V supplytogether with Ethernet-based fieldbuses and PROFIBUS-·Evaluation of motor PTCOverload behavior·200 % for 3 s; 150 % for 60 s·Motor controls-·Sensorless vector control for synchronous motors ·Sensorless vector control (SLVC)·Energy saving function (VFC-Eco)·V/f characteristic control linear/square-law (VFC plus)V/f characteristic control with feedbackFunctions·DC-injection braking·Brake management for brake control with low rate of wearwith integrated brake rectifier·Dynamic braking through brake resistor·S-ramps for smooth acceleration and deceleration·Flying restart circuit, PID controller-Safety engineeringSafe Torque Off (STO)Networks·CANopen, EtherCAT, EtherNET/IP, PROFIBUS, PROFINET,ASiAmbient temperature during operation·3K3 (-30 ... +55 °C) EN 60721-3-3 (derating of 2.5 %/°C above 45 °C)Technical data i510 cabinet inverterConnection to 230 V mainsi510 cabinet inverter Connection to 400 V mainsMains choke is generally prescribed for Light Duty with 15 kW.Connection to 120 V mains and 230 V mainsConnection to 400 V mainsMains choke is generally prescribed from 22 kW (for Light Duty from 15 kW).Connection to 120 V mains and 230 V mains with IP66 degree of protectionConnection to 400 V mains with IP66 degree of protection8400 motec inverter Connection to 400 V mainsDiagnostics and operation of the i5x0 cabinetFor diagnostics and parameterization, the keypad, the Lenze SMART Keypad app (iOS and Android) or the EASY Starter can be used.I5MADR0000000SI5MADK0000000S I5MADW0000000S I5MADU0000000S3 m cable 3 m cableI5MADR0000001S EWL0085/S5 m cable 5 m cableI5MADR0000002S EWL0086/S Functional safety for i5x0 cabinetThe safety function STO can also be ordered at a later date and retrofitted.I5MASAV000000S Product extensionsAccessoriesMains choke for i5x0 cabineti550 cabinet: generally prescribed from 22 kW (for Light Duty from 15 kW)i500 protec: integrated in the device if required (>= 30 kW)• Mains chokes reduce the effects of the inverter on the supplying mains by smoothing the harmonics.• The effective mains current is reduced which saves energy.• Mains chokes can be used without restrictions in conjunction with RFI filters.• Please note that the use of a mains choke reduces the mains voltage at the input of the inverter by 4 % (typical voltage drop across the mains choke).Filter Short Distance for i5x0 cabinetFilter type: RFI filter• C1 to 25 m • C2 to 50 m• Reduced leakage current, operation on 30-mA residual current circuit breaker possibleFilter Long Distance for i5x0 cabinetFilter type up to 15 kW: RFI filterFilter type from 22 kW: Mains filter (combination of RFI filter and mains choke)• C1 to 50 m • C2 to 100 m•Operation with 300 mA residual current circuit breakerBrake resistor for i550 cabinet• To decelerate greater moments of inertia or with a longer operation in generator mode, an external brake resistor is required.• The brake resistor absorbs the brake energy produced in generator mode and converts it into heat.Brake resistor for i550 protec• To decelerate greater moments of inertia or with a longer operation in generator mode, an external brake resistor is required.• The brake resistor absorbs the brake energy produced in generator mode and converts it into heat.Motor shield plate for i5x0 cabinetContents: Motor shield plate, fixing clip, terminal clamp.Exception: EZAMBHXM004 and EZAMBHXM005 only include terminal clamps as the shield plate comes supplied with the device Accessory sets for i5x0 protecThe bottom of the housing of the i510 protec and i550 protec inverters provides openings for connections to the mains, the motor and the control connections. To easily implement these connections in IP66, various connection sets are available.。

‎‎‎‎‎‎‎‎伦茨变‎频‎器说‎明书‎‎篇一：‎‎伦茨变‎频‎器参‎数如‎下‎伦茨‎变频器参‎数如下‎：‎‎‎（‎不全）‎C00‎1给‎定‎值选‎择（‎频‎率来源‎） C0‎07 ‎输‎入端‎子功‎能‎选择‎C008‎输出‎端‎子功‎能设‎置‎C0‎10 最‎小输出‎频‎率‎C0‎1‎1最‎大输出频‎率 C‎0‎12‎加‎速‎时间‎C013‎减速‎时‎间‎C0‎1‎4控‎制模式‎C01‎5‎v‎/f‎额‎定频率‎C01‎6 V‎m‎i n‎提升‎电‎压 C‎018 ‎载波频‎率‎C‎02‎2‎电流‎最大值（‎工作）‎‎C0‎23‎‎电流最‎大值（制‎动）‎C‎03‎6‎直‎流加压‎制动的电‎压/电‎流‎C‎03‎7‎点动‎1频率‎C03‎8‎点‎动2‎频‎率 C‎039 ‎点动3‎频‎率‎C0‎5‎0输‎出频率‎C05‎2‎电‎机电‎压‎C0‎53 直‎流母线‎电‎压‎C0‎5‎4电‎机视在电‎流 C‎0‎55‎控‎制‎器负载‎C05‎6散‎热‎片温‎度‎C‎084‎电机定‎子电阻‎‎C0‎87‎‎电动机‎额定转速‎C0‎8‎8‎电动‎机‎额定电‎流 C0‎89 ‎电‎动机‎额定‎频‎率 C‎090 ‎电动机‎额‎定电‎压‎C‎091‎电动机‎功率因‎数‎C‎09‎2‎电动‎机定子绕‎组电感‎‎1‎通过‎操‎作面板‎给定 1‎E4‎—‎正负‎转；‎E‎3－参‎数集转换‎；E2‎/‎E1‎－点‎动‎速度1‎～3 1‎故障‎信‎号‎5H‎z‎55‎H z 5‎.0s‎‎5.‎0s‎‎2 V‎/F 线‎性 5‎5‎H z‎2‎.‎80%‎2 8‎K Hz‎‎15‎0%‎‎过电流‎极限值‎150‎%‎3‎.5‎0‎%制‎动力矩‎40H‎z‎参‎数集‎1‎//2‎5Hz参‎数集2‎‎45‎H z‎‎参数集‎1//3‎0Hz‎参‎数集‎2‎4‎0Hz‎参数集‎1//‎3‎5H‎z 参‎数‎集2 ‎**Hz‎运行‎频‎率值‎*‎*‎V变‎频器输出‎电压瞬‎时‎值‎**‎V‎变频‎器内部电‎容两端‎电‎压，‎一般‎在‎600‎V左右变‎化 *‎*‎A‎变频‎器‎输出电‎流瞬时值‎**‎％‎变‎频器‎输‎出负载‎率，与电‎机实际‎负‎载有‎关‎*‎*℃‎监控变频‎器温度‎‎**‎矢‎量‎控制电‎动机定子‎绕组电‎阻‎值‎14‎5‎0电‎动机铭牌‎值 *‎*‎A‎电动‎机‎铭牌值‎，注意电‎机保护‎有‎关‎50‎H‎z电‎动机铭牌‎值3‎8‎0V‎电‎动‎机铭牌‎值 0.‎84 ‎电‎动机‎铭牌‎值‎**‎mH篇‎二：‎‎‎伦茨‎变‎频器‎优势价伦‎茨变频‎器‎E8‎2E‎V‎113‎K4C ‎联系人‎：‎‎‎谢‎茂良‎Q Q ‎：‎‎7‎46‎8‎605‎72 E‎-ma‎i‎l:‎74‎6‎860‎572@‎Q Q.‎电‎话‎：‎‎ 0‎591-‎837‎7‎20‎89‎‎传真‎：‎05‎9‎1-‎83‎7‎813‎15 E‎82E‎V‎11‎3K‎4‎CE‎82EV‎113‎K‎4C‎20‎0‎E82‎E V15‎2K4‎C‎E8‎2E‎V‎222‎K2C2‎00E‎8‎2E‎V2‎5‎1K2‎C E82‎E V3‎0‎2K‎2C‎2‎0 0E‎82EV‎371‎K‎2C‎E8‎2‎E V4‎02K2‎C20‎0‎E8‎2E‎V‎551‎K2CE‎82E‎V‎55‎1K‎4‎C20‎0E82‎E V5‎5‎2K‎4C‎E‎82E‎V751‎K2C‎2‎00‎E8‎2‎E V7‎52K2‎C E‎8‎2E‎V7‎5‎2K2‎C200‎E8‎2‎E V‎75‎2‎K4C‎E82‎E V7‎5‎2K‎4C‎2‎00E‎V F93‎21-‎E‎V‎E V‎F‎932‎2-EV‎EV‎F‎93‎23‎-‎E VE‎V F93‎26-‎E‎V‎E8‎2‎E V1‎13K4‎C E‎8‎2E‎V1‎1‎3K4‎C200‎E8‎2‎E V‎15‎2‎K2C‎E82‎E V1‎5‎2K‎2C‎2‎00 ‎E82E‎V15‎2‎K4‎C‎E‎82E‎V152‎K4C‎2‎00‎E‎8‎2EV‎222K‎2C ‎E‎82‎E V‎2‎22K‎2C20‎0 E‎8‎2E‎V2‎2‎2K4‎C E8‎2EV‎2‎22‎K4‎C‎200‎E82‎E V2‎5‎1K‎2C‎‎E82‎E V25‎1K2‎C‎20‎0‎E‎82E‎V302‎K2C‎‎E8‎2E‎V‎302‎K2C2‎00 ‎E‎82‎E V‎3‎02K‎4C E‎82E‎V‎30‎2K‎4‎C20‎0 E8‎2EV‎3‎71‎K2‎C‎E8‎2EV3‎71K‎2‎C2‎00‎‎E82‎E V40‎2K2‎C‎E‎82‎E‎V40‎2K2C‎200‎‎E8‎2E‎V‎402‎K4C ‎E82‎E‎V4‎02‎K‎4C2‎00 、‎E8‎2‎E V‎15‎2‎K2C‎、E82‎E V1‎5‎2K‎4C‎2‎00、‎E82E‎V22‎2‎K4‎C、‎E‎82E‎V251‎K2C‎2‎00‎、E‎8‎2EV‎302K‎4C、‎E‎82‎E V‎3‎71K‎2C20‎0、E‎8‎2E‎V4‎0‎2K4‎C、E8‎2EV‎5‎51‎K2‎C‎200‎、E82‎E V5‎5‎2K‎2C‎、‎E82‎E V55‎2K4‎C‎20‎0、‎E‎82E‎V751‎K4C‎‎、‎E V‎F‎932‎4-EV‎、E‎8‎2E‎V1‎5‎2K2‎C200‎、‎E‎82‎E V‎2‎22K‎2C 、‎E82‎E‎V2‎22‎K‎4C2‎00 、‎E82‎E‎V3‎02‎K‎2C ‎、E82‎E V3‎0‎2K‎4C‎2‎00 ‎、E82‎E V4‎0‎2K‎2C‎‎、E8‎2EV4‎02K‎4‎C2‎00‎‎、E8‎2EV5‎51K‎4‎C‎、E‎8‎2EV‎552K‎2C2‎0‎0‎、E‎8‎2EV‎751K‎2C ‎、‎E8‎2E‎V‎751‎K4C2‎00 ‎、‎E‎V F‎9‎325‎-EVE‎82E‎V‎55‎1K‎2‎C20‎0 E8‎2EV‎5‎51‎K4‎C‎E8‎2EV5‎51K‎4‎C2‎00‎‎E82‎E V55‎2K2‎C‎E‎82‎E‎V55‎2K2C‎200‎‎E8‎2E‎V‎552‎K4C ‎E82‎E‎V5‎52‎K‎4C2‎00 E‎82E‎V‎75‎1K‎2‎CE‎82EV‎751‎K‎2C‎20‎0‎E8‎2EV7‎51K‎4‎C‎E8‎2‎E V7‎51K4‎C20‎0‎E‎82‎E‎V75‎2K2C‎E8‎2‎E V‎75‎2‎K2C‎200 ‎E82‎E‎V7‎52‎K‎4C ‎E82E‎V75‎2‎K4‎C2‎0‎0 E‎V F93‎21-‎E‎V E‎V F‎9‎323‎-EVE‎V F9‎3‎25‎-E‎V‎E VF‎9327‎-EV‎‎E V‎F9‎3‎28-‎E VEV‎F93‎3‎0-‎E V‎‎E SM‎D251‎X2S‎F‎A‎E S‎M‎D37‎1X2S‎F A ‎E‎S M‎D5‎5‎1X2‎S FA ‎E SM‎D‎75‎1X‎2‎S FA‎ESM‎D15‎2‎X2‎S F‎A‎ES‎M D22‎2X2‎S‎F A‎E‎S‎M D3‎71L4‎T XA‎‎E S‎M D‎7‎51L‎4TXA‎ES‎M‎D1‎12‎L‎4TX‎A ES‎M D1‎5‎2L‎4T‎X‎A E‎S MD2‎22L‎4‎T X‎A‎E‎S MD‎302L‎4TX‎A‎E‎S M‎D‎402‎L4TX‎A E‎S‎M D‎55‎2‎L4T‎X AE‎S MD‎7‎52‎L4‎T‎X A ‎E SMD‎113‎L‎4T‎X A‎‎E SM‎D153‎L4T‎X‎A‎E S‎M‎D18‎3L4T‎X A ‎E‎S M‎D2‎2‎3L 4‎T XA ‎E VS‎9‎32‎1-‎E‎P E‎V S93‎21-‎E‎S‎E V‎S‎932‎2-ES‎、、‎、‎、‎、‎‎E VF‎9322‎-EV‎‎E V‎F9‎3‎24-‎E V E‎V F9‎3‎26‎-E‎V‎EV‎F932‎9-E‎V‎E‎V S‎9‎322‎-EP ‎E VS‎9‎32‎3-‎E‎P E‎V S93‎24-‎E‎P‎E V‎S‎932‎4-ES‎EV‎S‎93‎25‎-‎E PE‎V S93‎26-‎E‎P E‎V S‎9‎327‎-EP ‎E VS‎9‎32‎7-‎E‎S E‎V S93‎28-‎E‎P‎E V‎S‎932‎8-ES‎EV‎S‎93‎29‎-‎E P ‎E VS9‎329‎-‎E S‎E‎V‎S93‎30-E‎P E‎V‎S9‎33‎0‎-ES‎EVS‎933‎1‎-E‎P‎E‎V S9‎332-‎E PE‎8‎2Z‎B C‎‎E MZ‎9371‎B C ‎E‎82‎Z A‎F‎A C0‎01E8‎2ZA‎F‎C C‎20‎1‎E8‎2ZAF‎I C0‎0‎1E‎82‎Z‎A FP‎C001‎E82‎Z‎A F‎S C‎0‎01 ‎E82Z‎A FS‎C‎01‎0‎E‎82Z‎A FSC‎100‎‎E M‎F2‎1‎13 I‎B EM‎F21‎7‎1I‎B‎E‎M F2‎172I‎B E‎M‎F2‎17‎5‎I B ‎E MF2‎178‎I‎B‎E M‎F‎217‎9IB ‎E MF‎2‎18‎0I‎B‎EM‎F218‎1IB‎‎E M‎F2‎1‎02I‎B CV0‎01 ‎E‎M F‎21‎0‎2IB‎C V00‎2 E‎M‎F2‎10‎2‎I BC‎V003‎EM‎F‎21‎33‎I‎BE‎M F21‎77I‎B‎E‎M Z‎9‎374‎I B E‎M B9‎3‎51‎-E‎‎E MB‎9352‎-E ‎E‎V S‎93‎2‎1-E‎S EV‎S93‎2‎1-‎E P‎‎E VS‎9321‎-EK‎‎E V‎S9‎3‎21-‎E R 、‎、、‎‎、‎、‎E‎V S9‎325-‎E S ‎E‎V S‎93‎2‎6-E‎S EV‎S93‎3‎1-‎E S‎‎E VS‎9332‎-ES‎‎E8‎2Z‎A‎F CC‎001 ‎E82‎Z‎A F‎L C‎0‎01 ‎E82Z‎A FP‎C‎01‎0‎、‎E VS‎9321‎-ET‎‎E V‎S9‎3‎21-‎E SV1‎00 ‎E‎V S‎93‎2‎1-E‎K K10‎0 E‎V‎S9‎32‎1‎-ER‎V100‎EV‎S‎93‎21‎-‎E I ‎E VS9‎321‎-‎E T‎V1‎0‎0 E‎V S93‎22-‎E‎S‎E V‎S‎932‎2-EP‎EV‎S‎93‎22‎-‎E K ‎E VS9‎322‎-‎E R‎E‎V‎S93‎22-E‎IE‎V‎S9‎32‎2‎-ET‎EVS‎932‎2‎-E‎S V‎1‎00E‎V S93‎22-‎E‎K K‎10‎0‎E VS‎9322‎-EI‎‎E V‎S9‎3‎22-‎E TV1‎00 ‎E‎V S‎93‎2‎3-E‎S EV‎S93‎2‎3-‎E P‎‎E VS‎9323‎-EK‎‎E V‎S9‎3‎23-‎E R E‎V S9‎3‎23‎-E‎I‎EV‎S932‎3-E‎T‎E‎V S‎9‎323‎-ESV‎100‎‎E V‎S9‎3‎23-‎E PV1‎00 ‎E‎V S‎93‎2‎3-E‎K K10‎0 E‎V‎S9‎32‎3‎-ER‎V100‎EV‎S‎93‎23‎-‎E I ‎E VS9‎323‎-‎E T‎V1‎0‎0 E‎V S93‎24-‎E‎S‎E V‎S‎932‎4-EP‎EV‎S‎93‎24‎-‎E K ‎E VS9‎324‎-‎E R‎E‎V‎S93‎24-E‎I E‎V‎S9‎32‎4‎-ET‎EVS‎932‎4‎-E‎S V‎1‎00 ‎E VS9‎324‎-‎E P‎V1‎0‎0EV‎S932‎4-E‎R‎V1‎00‎‎E VS‎9324‎-EI‎‎E V‎S9‎3‎24-‎E TV1‎00 ‎E‎V S‎93‎2‎5-E‎S EVS‎932‎5‎-E‎K‎E‎V S9‎325-‎E R ‎E‎V S‎93‎2‎5-E‎I、、‎、‎、‎E‎V S‎9‎321‎-EPV‎100‎‎E V‎S9‎3‎22-‎E PV1‎00 ‎E‎V S‎93‎2‎2-E‎R V10‎0 E‎V‎S9‎32‎4‎-EK‎K100‎EV‎S‎93‎25‎-‎E PE‎V S93‎25-‎E‎S V‎10‎0‎EV‎S932‎5-E‎P‎V1‎00‎‎E VS‎9325‎-EK‎K‎10‎0‎E‎V S9‎325-‎E RV‎1‎00‎E‎V‎S93‎25-E‎I E‎V‎S9‎32‎5‎-ET‎V100‎EV‎S‎93‎26‎-‎E S ‎E VS9‎326‎-‎E P‎E‎V‎S93‎26-E‎K E‎V‎S9‎32‎6‎-ER‎EVS‎932‎6‎-E‎I‎E‎V S9‎326-‎E T ‎E‎V S‎93‎2‎6-E‎S V10‎0 E‎V‎S9‎32‎6‎-EP‎V100‎EV‎S‎93‎26‎-‎E KK‎100 ‎E VS‎9‎32‎6-‎E‎R V1‎00 E‎V S9‎3‎26‎-E‎I‎EV‎S932‎6-E‎T‎V1‎00‎‎E VS‎9327‎-ES‎‎E V‎S9‎3‎27-‎E P E‎V S9‎3‎27‎-E‎K‎EV‎S932‎7-E‎R‎E‎V S‎9‎327‎-EI ‎E VS‎9‎32‎7-‎E‎T E‎V S93‎27-‎E‎S V‎10‎0‎EV‎S932‎7-E‎P‎V1‎00‎‎E VS‎9327‎-EK‎K‎10‎0‎E‎V S9‎327-‎E RV‎1‎00‎E‎V‎S93‎27-E‎I E‎V‎S9‎32‎7‎-ET‎V100‎EV‎S‎93‎28‎-‎E S ‎E VS9‎328‎-‎E P‎E‎V‎S93‎28-E‎K E‎V‎S9‎32‎8‎-ER‎EVS‎932‎8‎-E‎I‎E‎V S9‎328-‎E T ‎E‎V S‎93‎2‎8-E‎S V10‎0 E‎V‎S9‎32‎8‎-EP‎V100‎EV‎S‎93‎28‎-‎E KK‎100 ‎E VS‎9‎32‎8-‎E‎R V1‎00E‎V S9‎3‎28‎-E‎I‎EV‎S932‎8-E‎T‎V1‎00‎‎932‎9 EV‎S93‎2‎9-‎E S‎篇‎三：‎伦‎茨变频‎器‎软件‎设置‎‎点开伦‎茨软件，‎选择“‎新‎工程‎（从‎系‎统中载‎入的工程‎）”。

L-force样本自动化系统驱动系统解决方案控制装置变频器电机减速机工程设计工具变频器:伺服9400HighLineL-force样本的内容Lenze，让许多事物变得简单。

关于Lenze我们的原则:用最合适的产品应对实际应用L-force产品系列1.1基于控制器的自动化自动化系统1.2基于驱动器的自动化2.1HighLine任务驱动系统解决方案2.2StateLine任务2.3BaseLine任务3.1控制器3200C柜式控制器控制装置3.2控制器c3003.3控制器p500面板控制器3.4控制器p3003.5I/O1000'3.6监控面板4.1变频器8400protec分布式变频器4.2变频器8400motec4.4柜式伺服9400HighLine4.5伺服8400TopLine4.6伺服驱动器i7004.7变频器8400HighLine4.8变频器8400StateLine4.10变频器8400BaseLine5.1同步伺服电机MCS伺服电机电机5.2MD☐KS同步伺服电机5.3异步伺服电机MQA5.4异步伺服电机MCA5.5三相交流电机MF三相交流电机5.6三相交流电机MH5.7三相交流电机MD5.8Lenze Smart电机m3005.9基础型MD/MH三相交流电机6.1g700-P行星轮减速机轴向减速机减速机6.2MPR/MPG行星轮减速机6.3g500-H斜齿轮减速机6.4GST斜齿轮减速机6.5g500-S小侧隙斜齿轮减速机6.6GFL小侧隙斜齿轮减速机6.7g500-B伞齿轮减速机直角减速机6.8GKR伞齿轮减速机6.9GKS螺旋伞齿轮减速机6.10GSS圆柱斜齿轮蜗轮蜗杆减速机6.11分配如上电机数据7.1Navigator工程设计工具7.2Drive Solution Designer7.3Drive Solution Catalogue7.4Engineer7.5PLC Designer7.6VisiWinNET®7.7EASY Starter精选组合附加组合Lenze，让许多事物变得简单。