汽车变速器设计
----------外文翻译
我们知道，汽车发动机在一定的转速下能够达到最好的状态，此时发出的功率比较大，燃油经济性也比较好。因此，我们希望发动机总是在最好的状态下工作。但是，汽车在使用的时候需要有不同的速度，这样就产生了矛盾。这个矛盾要通过变速器来解决。
汽车变速器的作用用一句话概括，就叫做变速变扭，即增速减扭或减速增扭。为什么减速可以增扭，而增速又要减扭呢？设发动机输出的功率不变，功率可以表示为 N = w T，其中w是转动的角速度，T是扭距。当N固定的时候，w与T是成反比的。所以增速必减扭，减速必增扭。汽车变速器齿轮传动就根据变速变扭的原理，分成各个档位对应不同的传动比，以适应不同的运行状况。
一般的手动变速器内设置输入轴、中间轴和输出轴，又称三轴式，另外还有倒档轴。三轴式是变速器的主体结构，输入轴的转速也就是发动机的转速，输出轴转速则是中间轴与输出轴之间不同齿轮啮合所产生的转速。不同的齿轮啮合就有不同的传动比，也就有了不同的转速。例如郑州日产ZN6481W2G型SUV车手动变速器，它的传动比分别是：1档3.704:１；2档2.202:1；3档1.414:1；4档1:1；5档（超速档）0.802:1。
当汽车启动司机选择1档时，拨叉将1/2档同步器向后接合1档齿轮并将它锁定输出轴上，动力经输入轴、中间轴和输出轴上的1档齿轮，1档齿轮带动输出轴，输出轴将动力传递到传动轴上（红色箭头）。典型1档变速齿轮传动比是3:1,也就是说输入轴转3圈，输出轴转1圈。
当汽车增速司机选择2档时，拨叉将1/2档同步器与1档分离后接合2档齿轮并锁定输出轴上，动力传递路线相似，所不同的是输出轴上的1档齿轮换成2档齿轮带动输出轴。典型2档变速齿轮传动比是2.2:1，输入轴转2.2圈，输出轴转1圈，比1档转速增加，扭矩降低。
当汽车加油增速司机选择3档时，拨叉使1/2档同步器回到空档位置，又使3/4档同步器移动直至将3档齿轮锁定在输出轴上，使动力可以从轴入轴—中间轴—输出轴上的3档变速齿轮，通过3档变速齿轮带动输出轴。典型3档传动比是1.7:1，输入轴转1.7圈，输出轴转1圈，是进一步的增速。
当汽车加油增速司机选择4档时，拨叉将3/4档同步器脱离3档齿轮直接与输入轴主动齿轮接合，动力直接从输入轴传递到输出轴，此时传动比1:1，即输出轴与输入轴转速一样。由于动力不经中间轴，又称直接档，该档传动比的传动效率最高。汽车多数运行时间都用直接档以达到最好的燃油经济性。
换档时要先进入空档，变速器处于空档时变速齿轮没有锁定在输出轴上，它们不能带动输出轴转动，没有动力输出。
一般汽车手动变速器传动比主要分上述1－4档，通常设计者首先确定最低（1档）与最高（4档）传动比后，中间各档传动比一般按等比级数分配。另外，还有倒档和超速档，超速档又称为5档。
当汽车要加速超过同向汽车时司机选择5档，典型5档传动比是0.87:1，也就是用大齿轮带动小齿轮，当主动齿轮转0.87圈时，被动齿轮已经转完1圈了。
倒档时输出轴要向相反方向旋转。如果一对齿轮啮合时大家反向旋转，中间加上一个齿轮就会变成同向旋转。利用这个原理，倒档就要添加一个齿轮做“媒介”，将轴的转动方向调转，因此就有了一根倒档轴。倒档轴独立装在变速器壳内，与中间轴平行，当轴上齿轮分别与中间轴齿轮和输出轴齿轮啮合时，输出轴转向会相反。
通常倒档用的同步器也控制5档的接合，所以5档与倒档位置是在同一侧的。由于有中间齿轮，一般变速器倒档传动比大于1档传动比，增扭大，有些汽车遇到陡坡用前进档上不去就用倒档开上去。
从驾驶平顺性考虑，变速器档位越多越好，档位多相邻档间的传动比的比值变化小，换档容易而且平顺。但档位多的缺点就是变速器构造复杂，体积大，现
在轻型汽车变速器一般是4－5档。同时，变速器传动比都不是整数，而是都带小数点的，这是因为啮合齿轮的齿数不是整倍数所致，两齿轮齿数是整倍数就会导致两齿轮啮合面磨损不均匀，使得轮齿表面质量产生较大的差异。
手动变速器与同步器
手动变速器是最常见的变速器，简称MT。它的基本构造用一句话概括，就是两轴一中轴，即指输入轴、轴出轴和中间轴，它们构成了变速器的主体，当然还有一根倒档轴。手动变速器又称手动齿轮式变速器，含有可以在轴向滑动的齿轮，通过不同齿轮的啮合达到变速变扭目的。典型的手动变速器结构及原理如下。
输入轴也称第一轴，它的前端花键直接与离合器从动盘的花键套配合，从而传递由发动机过来的扭矩。第一轴上的齿轮与中间轴齿轮常啮合，只要轴入轴一转，中间轴及其上的齿轮也随之转动。中间轴也称副轴，轴上固连多个大小不等的齿轮。输出轴又称第二轴，轴上套有各前进档齿轮，可随时在操纵装置的作用下与中间轴的对应齿轮啮合，从而改变本身的转速及扭矩。输出轴的尾端有花键与传动轴相联，通过传动轴将扭矩传送到驱动桥减速器。
由此可知，变速器前进档位的驱动路径是：输入轴常啮齿轮－中间轴常啮齿轮－中间轴对应齿轮－第二轴对应齿轮。倒车轴上的齿轮也可以由操纵装置拨动，在轴上移动，与中间轴齿轮和输出轴齿轮啮合,以相反的旋转方向输出。
多数汽车都有5个前进档和一个倒档，每个档位有一定的传动比，多数档位传动比大于1，第4档传动比为1，称为直接档，而传动比小于1的第5档称为加速档。空档时输出轴的齿轮处于非啮合位置，无法接受动力传输。
由于变速器输入轴与输出轴以各自的速度旋转，变换档位时合存在一个"同步"问题。两个旋转速度不一样齿轮强行啮合必然会发生冲击碰撞，损坏齿轮。因此，旧式变速器的换档要采用"两脚离合"的方式，升档在空档位置停留片刻，减档要
在空档位置加油门，以减少齿轮的转速差。但这个操作比较复杂，难以掌握精确。因此设计师创造出"同步器"，通过同步器使将要啮合的齿轮达到一致的转速而顺利啮合。
目前全同步式变速器上采用的是惯性同步器，它主要由接合套、同步锁环等组成，它的特点是依靠摩擦作用实现同步。接合套、同步锁环和待接合齿轮的齿圈上均有倒角（锁止角），同步锁环的内锥面与待接合齿轮齿圈外锥面接触产生摩擦。锁止角与锥面在设计时已作了适当选择，锥面摩擦使得待啮合的齿套与齿圈迅速同步，同时又会产生一种锁止作用，防止齿轮在同步前进行啮合。当同步锁环内锥面与待接合齿轮齿圈外锥面接触后，在摩擦力矩的作用下齿轮转速迅速降低（或升高）到与同步锁环转速相等，两者同步旋转，齿轮相对于同步锁环的转速为零，因而惯性力矩也同时消失，这时在作用力的推动下，接合套不受阻碍地与同步锁环齿圈接合，并进一步与待接合齿轮的齿圈接合而完成换档过程
自动变速器
自动变速器的选挡杆相当于手动变速器的变速杆，一般有以下几个挡位：P(停车)、R(倒挡)、N(空挡)、D(前进)、S(or2，即为2速挡)、L(or1，即为1速挡)。这几个挡位的正确使用对于驾驶自动变速器汽车的人来说尤其重要，下面就让我们一起来熟悉一下自动变速器各挡位的使用要领。
●P(停车挡)的使用
发动机运转时只要选挡杆在行驶位置上，自动变速器汽车就很容易地行走。而停放时，选挡杆必须扳入P位，从而通过变速器内部的停车制动装置将输出轴锁住，并拉紧手制动，防止汽车移动。
●R(倒挡)的使用
R位为倒挡，使用中要切记，自动变速器汽车不像手动变速器汽车那样能够使用半联动，故在倒车时要特别注意加速踏板的控制。
●N(空挡)的使用
N位相当于空挡，可在起动时或拖车时使用。在等待信号或堵车时常常将选挡杆保持在D位，同时踩下制动。若时间很短，这样做是允许的，但若停止时间长时最好换入N位，并拉紧手制动。因为选挡杆在行驶位置上，自动变速器汽车一般都有微弱的行驶趋势，长时间踩住制动等于强行制止这种趋势，使得变速器油温升高，油液容易变质。尤其在空调器工作、发动机怠速较高的情况下更为不利。有些驾驶员为了节油，在高速行驶或下坡时将选挡杆扳到N位滑行，这很容易烧坏变速器，因为这时变速器输出轴转速很高，而发动机却在怠速运转，油泵供油不足，润滑状况恶化，易烧坏变速器。
●D(前进挡)的使用
正常行驶时将选挡杆放在D位，汽车可在1～4挡(或3挡)之间自动换挡。D 位是最常用的行驶位置。需要掌握的是：由于自动变速器是根据油门大小与车速高低来确定挡位的，所以加速踏板操作方法不同，换挡时的车速也不相同。如果起步时迅速将加速踏板踩下，升挡晚，加速能力强，到一定车速后，再将加速踏板很快松开，汽车就能立即升挡，这样发动机噪声小，舒适性好。
D位的另一个特点是强制低挡，便于高速时超车，在D位行驶中迅速将加速踏板踩到底，接通强制低挡开关就能自动减挡，汽车很快加速，超车之后松开加速踏板又可自动升挡。
●S、L位低挡的使用
自动变速器在S位或L位上处于低挡范围，可以在坡道等情况下使用。下坡时换入S位或L位能充分利用发动机制动，避免车轮制动器过热，导致制动效能下降。但是从D位换入S位或L位时，车速不能高于相应的升挡车速，否则发动机会强烈振动，使变速器油温急剧上升，甚至会损坏变速器。
另外在雨雾天气时，若路面附着条件差，可以换入S位或L位，固定在某一低挡行驶，不要使用能自动换挡的位置，以免汽车打滑。同时必须牢记，打滑时
可将选挡杆推入N位，切断发动机的动力，以保证行车安全。
原文：
Transmission design
As we all know,automobile engine to a certain speed can be achieved under the best conditions, when compared issued by the power, fuel economy is relatively good. Therefore, we hope that the engine is always in the best of conditions to work under. However, the use of motor vehicles need to have different speeds, thus creating a conflict. Transmission through this conflict to resolve.
Automotive Transmission role sum up in one sentence, called variable speed twisting, twisting or slow down the growth rate by increasing torsional. Why can slow down by twisting, and the growth rate but also by twisting? For the same engine power output, power can be expressed as N = wT, where w is the angular velocity of rotation, and T Niuju. When N fixed, w and T is inversely proportional to the. Therefore, the growth rate will reduce twisting, twisting slowdown will increase. Automotive Transmission speed gear based on the principle of variable twisted into various stalls of different transmission ratio corresponding to adapt to different operational conditions.
General to set up a manual gearbox input shaft, intermediate shaft and output shaft, also known as the three-axis, as well as Daodang axis. Three-axis is the main transmission structure, input shaft speed is the speed of the engine, the output shaft speed is the intermediate shaft and output shaft gear meshing between different from the speed. Different gears are different transmission ratio, and will have a different speed. For example Zhengzhourichan ZN6481W2G manual transmission car-SUV, its transmission ratio are: 1 ; stalls 2.202:1; stalls 1.414:1; stalls 1:1 5 stalls (speeding file) 0.802: 1.
When drivers choose a launch vehicle stalls, Plectrum will be 1 / 2 engagement with a back stall gear and output shaft lock it, the power input shaft, intermediate shaft and output shaft gear of a stall, a stall the output shaft gear driven, and the output shaft power will be transmitted to the drive shaft (red arrow). A typical stall Biansuchilun transmission ratio is 3:1, that is to say three laps to the input shaft and output shaft to a circle.
When the growth rate of car drivers choose two stalls, Plectrum will be 1 / 2- and file a joint separation after 2 stall and lock the output shaft gear, power transmission line similar, the difference is that the output shaft gear of a stall 2 stall replaced by the output shaft gear driven. 2 stall Biansuchilun typical transmission ratio is 2.2:1, 2.2 laps to the input shaft and output shaft to a circle than a stall speed increase, lower torque.
When refueling vehicle drivers growth stalls option 3, Plectrum to 1 / 2 back to the free position, and also allows the 3 / 4 Mobile stall until 3 in the output shaft gear lock, power can be into the shaft axis - intermediate shaft - the output shaft of the three stalls Biansuchilun, led through three stalls Biansuchilun output shaft. 3 stalls typical transmission ratio is 1.7:1, 1.7 laps to the input shaft and output shaft to a circle is further growth.
When car drivers Option 4 refueling growth stalls, Plectrum will be 3 / 4 from the 3- stall gear directly with the input shaft gear joint initiative, and power transmission directly from the input shaft to the output shaft, the transmission ratio at 1:1, that the input shaft and output shaft speed the same. The driving force without intermediate shaft, also known as direct file, the than the maximum transmission efficiency. Most cars run-time files are used directly to achieve the best fuel economy.
Shift into the first interval when, in a free transmission when Biansuchilun output shaft is not locked in, they can not rotate the output shaft driven, not power output.
General automotive manual transmission than the main 1-4 stalls, usually the first designers to determine the minimum (one stall) and maximum (4 files) transmission ratio, the middle stall drive by geometric progression than the general distribution. In addition, there are stalls Daodang and speeding, speeding also known as the five stalls.
When the car to accelerate to more than car drivers with the choice of five stalls, and a typical five-transmission ratio is 0.87:1, which is driven by a pinion gear, the gear when the initiative to 0.87 zone, passive gear have been transferred to a circle of the End.
Dao Dang, the opposite direction to the output shaft rotation. If one pair of meshing gears when we reverse rotation, with a middle gear, it will become the same to the rotation. Use of this principle, we should add a gear Daodang the "media" will
be rotational direction reversed, it will have a Daodang axis. Daodang installed in the transmission shaft independent crust, and the intermediate shaft parallel axis gear with the intermediate shaft and output shaft gear meshing gears, will be contrary to the output shaft.
Daodang usually used for the synchronization control also joins five stalls, stalls and Daodang 5 position in the same side. As a middle gear, the general transmission Daodang transmission ratio greater than 1 ratio, by twisting, steep slope with some vehicles encountered on the progress stalls falters with a Daodang boost.
Ride from the driver of the considerations, better transmission stall, stall adjacent stall more than the transmission changes the ratio of small, and easy to shift smoothly. However, the shortcomings of the stalls is more transmission structure is complicated, bulky, light vehicle transmission is generally 4-5 stalls. At the same time, transmission ratio is not integral, but with all of the decimal point, it is because of the gear teeth meshing is not caused by the whole multiples of two gear teeth can lead to the whole multiples of two meshing gears of uneven wear, making the tooth surface quality have a greater difference.
Manual transmission and synchronizer
Manual transmission is the most common transmission, or MT. Its basic structure sum up in one sentence, is a two-axle shaft, where input shaft, the shaft axis and intermediate shaft, which constitute the main body of the transmission and, of course, a Daodang axis. Manual transmission known as manual gear transmission, which can be in the axial sliding gears, the gears meshing different variable speed reached twisting purpose. Typical manual transmission structure and principles are as follows.
Input shaft also said that the first axis, and its front-end Spline driven directly with the clutch disc sets with the Spline, by the transfer of torque from the engine. The first axis of the intermediate shaft and gears meshing gears often, as long as the shaft axis to a turn, the intermediate shaft and gear also will be rotating. Vice also said intermediate shaft axis, the axis-even more than the size gear. Also known as the second output shaft axis, the axis of various sets of gear stall progress can be manipulated at any time in the role of the device and the corresponding intermediate shaft gear meshing, thus changing its speed and torque. With the end of the output shaft spline associated with the drive shaft through the drive shaft torque transmitted
to the drive axle reducer.
Thus, progress stalls drive transmission path is: input shaft gear often rodents - often rodents intermediate shaft gear - corresponding intermediate shaft gear - the second axis corresponding gear. Reversing the gear shaft can be manipulated by the device pick in the axis movement, and the intermediate shaft and output shaft gear meshing gears, to the contrary to the direction of rotation output.
Most cars have five stalls and a Daodang forward, a certain degree of each stall transmission ratio, the majority of stalls transmission ratio greater than 1, 4 ratio of 1, known as direct stalls, and transmission ratio is less than 1 No. 5 stall called accelerated stall. Free at the output shaft gear in a position of non-engagement, unacceptable power transmission.
The transmission input shaft and output shaft rotational speed to their own, transform a stall when there is a "synchronous". Two different rotational speed gear meshing force will impact the collision occurred, damage gear. Therefore, the old transmission shift to a "feet-off" approach, or stall on the location of the free stay for a while by stalls in the free position refueling doors, in order to reduce the speed differential gear. However, this operation is relatively more complicated and difficult to grasp accurate. So designers create a "synchronized," and allows synchronization through the meshing of gears to be consistent speed and smooth meshing.
At present Synchronous Transmission is based on the synchronization of inertia, mainly from joint sets, synchronous lock ring, and so on, it is characterized by friction on the role of synchronization. Splice sets Genlock engagement ring gear and the ring gear when it had Chamfer (Lock angle), Genlock within the cone ring gear engagement with the question of cone ring gear contact friction. Lock and cone angle has been made in the design of an appropriate choice to be made friction cone of the teeth meshing with the ring gear quickly sets pace at the same time will have a Lock role and to prevent the gears meshing in sync before. When synchronization lock cone ring gear engagement with the question of cone ring gear after contact in the effects of friction torque gear speed quickly lower (or higher) with the same speed synchronous lock ring, the two synchronous rotation of the gear Genlock Central zero speed, thus moment of inertia also disappear, then in force under the impetus of engagement sets unhindered and synchronization lock ring gear engagement, and further engagement with the question of gear engagement and the completion Gear Shift Process.
The automatic gearbox
The automatic gearbox chooses to block the pole the equal to moving the stick shift of the gearbox, having generally below several blocks:P( parking),
R( pour to block), N( get empty to block), D( go forward), S( or2, namely for 2 block soon), L.( or1, namely for 1 block soon)This several an usage for blocking a right usages coming driver the automatic gearbox is automotive of person to say particularly important, underneath let us very much familiar with once automatic gearbox eachly blockings main theme.
The usage of the P ( the parking blocks)
The launches the luck turns as long as choose to block the pole in driving the position, automatic gearbox car run about very easily.But park, choose to block the pole must pull into of P, from but pass the internal parking system in gearbox moves the device will output the stalk lock lives, combining to tense the hand system move, preventing the car ambulation.
The usage of the R( pour to block)
R a control for is pouring blocking, using inside wanting slicing recording, automatic gearbox car unlike moving gearbox car so can using half moving, so while reversing the car wanting special attention accelerating pedal.
The usage of the N( get empty to block)
The N is equal to get empty to block, can while starting or hour of trailer usage.At wait for the signal or block up the car will often often choose to block the pole keeps in the of D, trampling at the same time the next system move.If time is very short, do like this is an admission of, but if stop the time long time had better change into of N, combine to tense the hand system moves.Because choose to block the pole in driving the position, the automatic gearbox car has generally and all to drive the trend faintly, long hours trample the system move same as a deterrent this kind of trend, make gearbox oil gone up, the oil liquid changes in character easily.Particularly in the air condition machine work, launch the soon higher circumstance in machine bottom more disadvantageous.Some pilots for the sake of stanza oil, at made good time or go down slope will choose to block the pole pull the of N skids, this burn the bad gearbox very easily, launching the machine to revolves soon in the however because the gearbox outputs at this time the stalk turns soon very high,, the oil pump provides the oil shortage, lubricating the condition worsen, burn the bad gearbox easily.
The usage of the D( go forward to block)
Will choose to block when is normal to drive the pole put in the of D, car can at 1 ～4 block( or 3 block) its change to block automatically.The of D drives the position most in common usely.What demand control is:Because the automatic gearbox is soon high and low with car to come to make sure to block according to the accelerator size a, so accelerate the pedal operation method is different, changing to block the hour of the car is soon too not same alike.If start hour quick accelerate the pedal tramples the bottom, rising to block the night, accelerating the ability is strong, arriving certain car soon behind, then will accelerate the pedal loosen to open very quickly, car can rise to block immediately, launch like this the machine voice is small, comfortable good.
The another characteristics of the D is a compulsory low blocking, easy to high speed the hour overtakes a car, will accelerate quickly in of D drove the pedal trample after all, connect the compulsory low fend off the pass and then can reduce to block automatically, the car accelerates very quickly, after overtaking a car loosen to open the pedal of acceleration to can rise to block automatically again.
The usage of the S, of L low the usage that block
The automatic gearbox in in is placed in the low blocking the scope on of S or of Ls, can usage under an etc. circumstance.It change to can make use of to launch well into of S or of Ls the mechanism move, avoiding the car wheel system move the machine over hot, cause the system move the effect descent while going down slope.But change into from the of D of S or of L, car soon can't higher than rise to block the car homologously soon, otherwise strong vibration in opportunity to launch, make gearbox oil hoicked, even will damage the gearbox.
The is another at rain fog weather hour, if the road adheres to the term bad, can change into a position for or of L, fixing at somely first lowly blocking driving, doing not use can automatically changing blocking, in order to prevent the car beats slippery.Must keep firmly in mind at the same time, beat the slippery hour can will choose to block the pole pushes into a motive for, cutting off launching machine, toing guarantee a car the safety.
中英文对照外文翻译 汽车变速器设计 我们知道，汽车发动机在一定的转速下能够达到最好的状态，此时发出的功率比较大，燃油经济性也比较好。因此，我们希望发动机总是在最好的状态下工作。但是，汽车在使用的时候需要有不同的速度，这样就产生了矛盾。这个矛盾要通过变速器来解决。 汽车变速器的作用用一句话概括，就叫做变速变扭，即增速减扭或减速增扭。为什么减速可以增扭，而增速又要减扭呢？设发动机输出的功率不变，功率可以表示为 N = w T，其中w是转动的角速度，T 是扭距。当N固定的时候，w与T是成反比的。所以增速必减扭，减速必增扭。汽车变速器齿轮传动就根据变速变扭的原理，分成各个档位对应不同的传动比，以适应不同的运行状况。 一般的手动变速器内设置输入轴、中间轴和输出轴，又称三轴式，另外还有倒档轴。三轴式是变速器的主体结构，输入轴的转速也就是发动机的转速，输出轴转速则是中间轴与输出轴之间不同齿轮啮合所产生的转速。不同的齿轮啮合就有不同的传动比，也就有了不同的转速。例如郑州日产ZN6481W2G型SUV车手动变速器，它的传动比分别是：1档3.704:１；2档2.202:1；3档1.414:1；4档1:1；5档（超速档）0.802:1。 当汽车启动司机选择1档时，拨叉将1/2档同步器向后接合1档
齿轮并将它锁定输出轴上，动力经输入轴、中间轴和输出轴上的1档齿轮，1档齿轮带动输出轴，输出轴将动力传递到传动轴上（红色箭头）。典型1档变速齿轮传动比是3:1,也就是说输入轴转3圈，输出轴转1圈。 当汽车增速司机选择2档时，拨叉将1/2档同步器与1档分离后接合2档齿轮并锁定输出轴上，动力传递路线相似，所不同的是输出轴上的1档齿轮换成2档齿轮带动输出轴。典型2档变速齿轮传动比是2.2:1，输入轴转2.2圈，输出轴转1圈，比1档转速增加，扭矩降低。 当汽车加油增速司机选择3档时，拨叉使1/2档同步器回到空档位置，又使3/4档同步器移动直至将3档齿轮锁定在输出轴上，使动力可以从轴入轴—中间轴—输出轴上的3档变速齿轮，通过3档变速齿轮带动输出轴。典型3档传动比是1.7:1，输入轴转1.7圈，输出轴转1圈，是进一步的增速。 当汽车加油增速司机选择4档时，拨叉将3/4档同步器脱离3档齿轮直接与输入轴主动齿轮接合，动力直接从输入轴传递到输出轴，此时传动比1:1，即输出轴与输入轴转速一样。由于动力不经中间轴，又称直接档，该档传动比的传动效率最高。汽车多数运行时间都用直接档以达到最好的燃油经济性。 换档时要先进入空档，变速器处于空档时变速齿轮没有锁定在输出轴上，它们不能带动输出轴转动，没有动力输出。 一般汽车手动变速器传动比主要分上述1－4档，通常设计者首先确定最低（1档）与最高（4档）传动比后，中间各档传动比一
The development of automobile As the world energy crisis and the war and the energy consumption of oil -- and are full of energy in one day someday it will disappear without a trace. Oil is not inresources. So in oil consumption must be clean before finding a replacement. With the development of science and technology the progress of the society people invented the electric car. Electric cars will become the most ideal of transportation. In the development of world each aspect is fruitful especially with the automobile electronic technology and computer and rapid development of the information age. The electronic control technology in the car on a wide range of applications the application of the electronic device cars and electronic technology not only to improve and enhance the quality and the traditional automobile electrical performance but also improve the automobile fuel economy performance reliability and emission spurification. Widely used in automobile electronic products not only reduces the cost and reduce the complexity of the maintenance. From the fuel injection engine ignition devices air control and emission control and fault diagnosis to the body auxiliary devices are generally used in electronic control technology auto development mainly electromechanical integration. Widely used in automotive electronic control ignition system mainly electronic control fuel injection system electronic control ignition system electronic control automatic transmission electronic control ABS/ASR control system electronic control suspension system electronic control power steering system vehicle dynamic control system the airbag systems active belt system electronic control system and the automatic air-conditioning and GPS navigation system etc. With the system response the use function of quick car high reliability guarantees of engine power and reduce fuel consumption and emission regulations meet standards. The car is essential to modern traffic tools. And electric cars bring us infinite joy will give us the physical and mental relaxation. Take for example automatic transmission in road can not on the clutch can achieve automatic shift and engine flameout not so effective improve the driving convenience lighten the fatigue strength. Automatic transmission consists mainly of hydraulic torque converter gear transmission pump hydraulic control system electronic control system and oil cooling system etc. The electronic control of suspension is mainly used to cushion the impact of the body and the road to reduce vibration that car getting smooth-going and stability. When the vehicle in the car when the road uneven road can according to automatically adjust the height. When the car ratio of height low set to gas or oil cylinder filling or oil. If is opposite gas or diarrhea. To ensure and improve the level of driving cars driving stability. Variable force power steering system can significantly change the driver for the work efficiency and the state so widely used in electric cars. VDC to vehicle performance has important function it can according to the need of active braking to change the wheels of the car car motions of state and optimum control performance and increased automobile adhesion controlling and stability. Besides these appear beyond 4WS 4WD electric cars can greatly improve the performance of the value and ascending simultaneously. ABS braking distance is reduced and can keep turning skills effectively improve the stability of the directions simultaneously reduce tyre wear. The airbag appear in large programs protected the driver and passengers safety and greatly reduce automobile in collision of drivers and passengers in the buffer to protect the safety of life. Intelligent electronic technology in the bus to promote safe driving and that the other functions. The realization of automatic driving through various sensors. Except some smart cars equipped with multiple outside sensors can fully perception of information and traffic facilities
附录 附录A. Manual Transmission It’s no secret that cars with manual transmissions are usually more fun to drive than the automatic-equipped counterparts. If you have even a passing interest in the act of driving, then chances are you also appreciate a fine-shifting manual gearbox. But how does a manual transmission actually work? A history hows that manual transmissions preceded automatics by several decades. In fact，up until General Motors offered an automatic in 1938, all cars were of the shift-it-yourself variety. While it’s logical for many types of today’s vehicles to be equipped with an automatic――such as a full-size sedan, SUV or pickup――the fact remains that nothing is more of a thrill to drive than a tautly suspended sport sedan, snort coupe or two-sealer equipped with a precise-shifting five-or six-speed gearbox． We know whicn types or cars have manual trannies. Now let’s take a look at how they work. From the most basic four-speed manual in a car from the’60s to the most high-tech six-speed one in a car of today, the principles of a manual gearbox are the same. The driver must shift from gear to gear. Normally, a manual transmission bolts to a clutch housing (or bell housing）, in turn, bolts to the back of the engine. If the vehicle has front-wheel drive,
变速器设计文献综述 摘要：车辆的变速器很大程度上影响着车辆行驶的经济性、动力性、驾乘舒适性，是车辆最重要的部件之一。本文分析了国内外变速器产业的发展状况，介绍了国内外先进的变速器设计方法、科学的开发流程等，还根据我国变速器产业的发展现状提出了一些问题，并且对变速器产业的发展提出了一些合理的建议。 关键词：变速器，科学开发流程、先进设计方法 一.变速器研究意义 变速器是伴随汽车出现的产物，是组成一辆汽车的必需品，而变速器设计更是汽车设计中最重要的环节之一。变速器的作用是用来改变传动比，使发动机尽量工作在有利的工况下，满足不同的行驶要求。在不同的行驶条件下，要求汽车行驶速度和驱动扭矩能在很大范围内变化，而汽车发动机的特性是转速变化范围较小，扭矩变化范围更不可能满足实际路况需要，而变速器能做到在大范围内改变汽车行驶速度的大小和汽车驱动轮上扭矩的大小。因此,变速器的性能直接影响到汽车行驶性能。随着技术进步,变速器在最基本的传动功能之外，也在实现越来越多的功能，例如实现倒车行驶，用来满足汽车倒退行驶的需要; 中断动力传递，在发动机能够怠速运转，汽车换档或需要停车时，中断向驱动轮的动力传递; 实现空档，当离合器接合时，变速箱可以不输出动力。由此可见，研究变速器对汽车产业发展具有十分重大的意义。
二.国内外变速器使用的现状 在欧洲市场上，原本手动变速器占据的绝大部分的市场,在不断被自动变速器侵占。例如在西欧，2005年生产的装配有自动变速器的汽车占汽车总量的23%。而10年前，这个数字仅为13%。可见自动变速器正在成为市场的主流。在中国市场上，配备自动变速器也已经成为车用变速器的重要趋势。然而，在自动变速器方面，由于其新工艺、新技术和设计原理与传统手动变速器有比较大的差异，导致国内厂家在自动变速器的研发上与国际先进水平存在较大差距，即使向国外厂商寻求技术帮助，他们也不约而同地对国内厂家进行了技术封锁，这导致我国的自动变速器相比国外产品性能低下，需要大量依赖进口。据统计，进口产品占我国自动变速器市场的78%。而在手动变速器方面，经过长时间的发展，设计原理和生产工艺等都较为成熟，技术难度也相对较低，因此我国通过引进国外先进技术，消化吸收并自主创新，能做到自主生产，基本满足了本土车辆厂商的生产需要。可以预见的是，未来汽车变速器的市场将以自动变速器为主，发展和掌握高端自动变速器制造技术是追赶世界变速器制造技术的重要途径。而优先开发手自一体变速器在技术上可以延续我国在手动变速箱上积累的经验，更有利于我国变速器产业的发展。 三. 国外变速器先进的设计方法 近10年以来，我国变速器产业特别重视新产品的开发研制，无论是从人力物力的投入，还是资金的投入，都是非常巨大的。
汽车悬架原理外文文献及翻译 (文档含中英文对照即英文原文和中文翻译) The rinciple Of Car Suspensions By William Harris University of Michigan When people think of automobile performance, they normally think of horsepower, torque and zero-to-60 acceleration. But all of the power generated by a piston engine is useless if the driver can't control the car. That's why automobile engineers turned their attention to the suspension system almost as soon as they had mastered the four-stroke internal combustion engine. The job of a car suspension is to maximize the friction between the tires and the road surface, to provide steering stability with good handling and to ensure the comfort of the passengers. In this article, we'll explore how car suspensions work, how they've evolved over the years and where the design of suspensions is headed in the future.
外文翻译 文章出处《Tribology International》, 2009, 42(5):714-723 译文： 有限元热分析的陶瓷离合器 1 引言 磨料空转车辆离合器是力封闭联轴器。扭矩和高速传输被压紧表面之间产生的摩擦力所保证。应用陶瓷是因为它作为摩擦介质具有好耐热和耐磨损性能，提供了机会以驱动更高的压力，以及一个低的密度。因此，一个提功率密度启用了一个平行的最小化建筑空间。 测量使用陶瓷饰面离合器盘的第一个原型在卡尔斯鲁厄大学的一个实验室专门从事客车驱动系统进行了测试执行。在分析过程中的有限元（FE）模型是将与测量数据和测量条件的知识所构成。计算的目的是要确定在离合器盘上温度的分布以及环境中的在每一时刻的及时测量目。至关重要的是熟悉的温度范围，为了检验该系统的耐磨特性。因此，重要信息从测量数据中得出。在临界负载的情况下，预计最高温度必须在时间和空间上进行预测，为保护接近发热体的位置测量工具的。 本研究的目的是分析和修改该离合器系统通过改进，以提供更好的工作条件热传导和系统或增加转化成摩擦热的能量的对流。此外，人们希望找到更有效的更好的离合器系统设计方案。 计算是由宇宙星空的设计的软件进行的。在模型开发阶段，非常谨慎，必须采取几何元素，选择适当的简化尺寸，并且由于正确调整的时间步长大量的硬件要求瞬态计算。热物性参数的改变，如表面热对流化系数和热负荷，必须考虑到到在一个持续的基础上在时间和地点方面。离合器系统的分析测试这两方面，只能通过加热隔板连接的两个独立的模型来管理，根据该假说认为，接触温度必须是在两个相同的双方，同时他们要有适当接触，其价值需通过迭代来进行调整。计算显示，该热分区按周期变化，它沿不同的内，外接触环。在不同的冷却特性下，在陶瓷和钢之间的结果是不同的，热流从陶瓷侧面向钢侧流动。此热流也通过迭代确定;它的价值也改变了周期和不同沿着所述内和外接触环。 2 采用工程陶瓷作为摩擦材料的第一个原型机 这款检查过的离合器盘是根据“特定的陶瓷”产品而开发的，此材料的研发过程在流程在卡尔斯鲁厄大学的Institute for Product Development (IPEK)杂志上发表过。此开发过程已经具有的可能性，用于连接到一个真实的传动轴；甚至，它为面板有一个好的初始行为起到一个很好的缓冲作用。磨料配件必须符合以下基本要求：
原文： Transmission design As we all know automobile engine to a certain speed can be achieved under the best conditions, when compared issued by the power, fuel economy is relatively good. Therefore, we hope that the engine is always in the best of conditions to work under. However, the use of motor vehicles need to have different speeds, thus creating a conflict. Transmission through this conflict to resolve. Automotive Transmission role sum up in one sentence, called variable speed twisting, twisting or slow down the growth rate by increasing torsional. Why can slow down by twisting, and the growth rate but also by twisting? For the same engine power output, power can be expressed as N = WT, where w is the angular velocity of rotation. When N fixed, w and T is inversely proportional to the. Therefore, the growth rate will reduce twisting, twisting slowdown will increase. Automotive Transmission speed gear based on the principle of variable twisted into various stalls of different transmission ratio corresponding to adapt to different operational conditions. General to set up a manual gearbox input shaft, intermediate shaft and output shaft, also known as the three-axis, as well as Daodang axis. Three-axis is the main transmission structure, input shaft speed is the speed of the engine, the output shaft speed is the intermediate shaft and output shaft gear meshing between different from the speed. Different gears are different transmission ratio, and will have a different speed. For example Zhengzhou richan ZN6481W2G manual transmission car-SUV, its transmission ratio are: 1 File 3.704:1; stalls 2.202:1; stalls 1.414:1; stalls 1:1 5 stalls (speeding file) 0.802: 1. When drivers choose a launch vehicle stalls, Plectrum will be 1 / 2 file synchronization engagement with a back stall gear and output shaft lock it, the power input shaft, intermediate shaft and output shaft gear of a stall, a stall the output shaft gear driven, and the output shaft power will be transmitted to the drive shaft (red arrow). A typical stall Biansuchilun transmission ratio is 3:1, that is to say three laps
As the world energy crisis, and the war and the energy consumption of oil -- and are full of energy, in one day, someday it will disappear without a trace. Oil is not in resources. So in oil consumption must be clean before finding a replacement. With the development of science and technology the progress of the society, people invented the electric car. Electric cars will become the most ideal of transportation. In the development of world each aspect is fruitful, especially with the automobile electronic technology and computer and rapid development of the information age. The electronic control technology in the car on a wide range of applications, the application of the electronic device, cars, and electronic technology not only to improve and enhance the quality and the traditional automobile electrical performance, but also improve the automobile fuel economy, performance, reliability and emissions purification. Widely used in automobile electronic products not only reduces the cost and reduce the complexity of the maintenance. From the fuel injection engine ignition devices, air control and emission control and fault diagnosis to the body auxiliary devices are generally used in electronic control technology, auto development mainly electromechanical integration. Widely used in automotive electronic control ignition system mainly electronic control fuel injection system, electronic control ignition system, electronic control automatic transmission, electronic control (ABS/ASR) control system, electronic control suspension system, electronic control power steering system, vehicle dynamic control system, the airbag systems, active belt system, electronic control system and the automatic air-conditioning and GPS navigation system etc. With the system response, the use function of quick car, high reliability, guarantees of engine power and reduce fuel consumption and emission regulations meet standards. The car is essential to modern traffic tools. And electric cars bring us infinite joy will give us the physical and mental relaxation. Take for example, automatic transmission in road, can not on the clutch, can achieve automatic shift and engine flameout, not so effective improve the driving convenience lighten the fatigue strength. Automatic transmission consists mainly of hydraulic torque converter, gear transmission, pump, hydraulic control system, electronic control system and oil cooling system, etc. The electronic control of suspension is mainly used to cushion the impact of the body and the road to reduce vibration that car getting smooth-going and
外文翻译 Auto Transmission First, an overview of automotive transmission and the development trend Automobile available more than a century, especially from the mass production of motor vehicles and the automotive industry since the development of large, Car has been the economic development of the world for mankind to enter the modern life and have had a tremendous impact on the immeasurable, The progress of human society has made indelible contributions to the great, epoch-making set off arevolution. From From the vehicle as a power plant using internal combustion engine to start, auto transmission has become an important component. Is Generation is widely used in automotive reciprocating piston internal combustion engine with a small size, light weight, reliable operation and the use of The advantages of convenience, but its torque and speed range of smaller changes, and complex condition requires the use of motor vehicles Traction and the speed can be considerable changes in the scope. Therefore, its performance and vehicle dynamics and economy of There are large inter-contradictions, which contradictions of modern automotive internal combustion engine by itself is insoluble. Because Here, in the automotive power train set up the transmission and main reducer in order to achieve the purpose of deceleration by moment. Speed The main function of performance: ⑴ change gear ratio of motor vehicles, and expand the wheel drive torque and rotational speed of the Fan Wai, in order to adapt to constantly changing driving cycle, while the engine in the most favorable conditions within the scope of work; ⑵no change in the direction of engine rotation, under the premise of the realization of cars driving back; ⑶the realization of the free, temporary Interruption of power transmission, in order to be able to start the engine, idling, etc.. V ariable-speed drive transmission by the manipulation of institutions and agencies. Change the transmission ratio by way of transmission is divided into There are class-type, non-stage and multi-purpose three. Have class most widely used transmission. It uses gear drive, with a number of transmission ratio setting. Stepless transmission Continuously V ariable Transmission (CVT) transmission ratio of a certain The framework of multi-level changes may be unlimited, there is a common type of power and torque (dynamic fluid-type) and so on. Continuously V ariable Transmission Transmission development is the ultimate goal, because only it can make the most economical engine in working condition Can provide the best vehicle fuel economy and optimal power in order to provide the most comfortable By the feeling. Today's CVT is a typical representative of the CVT
汽车变速器设计 ----------外文翻译 我们知道，汽车发动机在一定的转速下能够达到最好的状态，此时发出的功率比较大，燃油经济性也比较好。因此，我们希望发动机总是在最好的状态下工作。但是，汽车在使用的时候需要有不同的速度，这样就产生了矛盾。这个矛盾要通过变速器来解决。 汽车变速器的作用用一句话概括，就叫做变速变扭，即增速减扭或减速增扭。为什么减速可以增扭，而增速又要减扭呢？设发动机输出的功率不变，功率可以表示为 N = w T，其中w是转动的角速度，T是扭距。当N固定的时候，w与T是成反比的。所以增速必减扭，减速必增扭。汽车变速器齿轮传动就根据变速变扭的原理，分成各个档位对应不同的传动比，以适应不同的运行状况。 一般的手动变速器内设置输入轴、中间轴和输出轴，又称三轴式，另外还有倒档轴。三轴式是变速器的主体结构，输入轴的转速也就是发动机的转速，输出轴转速则是中间轴与输出轴之间不同齿轮啮合所产生的转速。不同的齿轮啮合就有不同的传动比，也就有了不同的转速。例如郑州日产ZN6481W2G型SUV车手动变速器，它的传动比分别是：1档3.704:１；2档2.202:1；3档1.414:1；4档1:1；5档（超速档）0.802:1。 当汽车启动司机选择1档时，拨叉将1/2档同步器向后接合1档齿轮并将它锁定输出轴上，动力经输入轴、中间轴和输出轴上的1档齿轮，1档齿轮带动输出轴，输出轴将动力传递到传动轴上（红色箭头）。典型1档变速齿轮传动比是3:1,也就是说输入轴转3圈，输出轴转1圈。 当汽车增速司机选择2档时，拨叉将1/2档同步器与1档分离后接合2档齿轮并锁定输出轴上，动力传递路线相似，所不同的是输出轴上的1档齿轮换成2档齿轮带动输出轴。典型2档变速齿轮传动比是2.2:1，输入轴转2.2圈，输出轴转1圈，比1档转速增加，扭矩降低。
附录Ⅰ：外文资料 Automotive Suspension System Overview The impact of the Vehicle in many aspects, Suspension plays a very important role . The components of the suspension system perform six basic functions: 1.Maintain correct vehicle ride height. 2.Reduce the effect of shock forces. 3.Maintain correct wheel alignment. 4.Support vehicle weight. 5.Keep the tires in contact with the road. 6.Control the vehicle’s direction of travel. Most suspension systems have the same basic parts and operate basically in the same way. They differ, however, in the way the parts are arranged. The vehicle wheel is attached to a steering knuckle. The steering knuckle is attached to the vehicle frame by two control arms, which are mounted so they can pivot up and down. A coil spring is mounted between the lower control arm and the frame. When the wheel rolls over a bump, the control arms move up and compress the spring. When the wheel rolls into a dip, the control arms move down and the springs expand. The spring force brings the control arms and the wheel back into the normal position as soon as the wheel is on flat pavement. The idea is to allow the wheel to move up and down while the frame, body, and passengers stay smooth and level. The unequal length control arm or short, long arm (SLA) suspension system has been common on American vehicles for many years. Because each wheel is independently connected to the frame by a steering knuckle, ball joint assemblies, and upper and lower control arms, the system is often described as an independent suspension. The short, long arm suspension system gets its name from the use of two control arms from the frame to the steering knuckle and wheel assembly. The two control arms are of unequal length with a long control arm on the bottom and a short control arm on the top. The control arms are sometimes called A arms because in the top view they are shaped like the letter A. In the short, long arm suspension system, the upper control arm is attached to a cross shaft through two combination rubber and metal bushings. The cross shaft, in turn, is bolted to the frame. A ball joint, called the upper ball joint, is attached to the outer end of the upper arm and connects to the steering knuckle through a tapered stud held in position with a nut. The inner ends of the lower control arm have pressed-in