场地名称篇
field / pitch 足球场
midfield 中场
backfield 后场
kickoff circle / center circle 中圈halfway line 中线
touchline / sideline 边线
goal line 球门线
end line/goal line/ post line 底线penalty mark （点球）罚球点
penalty area 禁区（罚球区）
goal area 小禁区（球门区）
flank/ wing 辅位
woodwork 球门框
crossbar/ bar 门楣
goalpost/ post - 门柱
球队称谓篇
coach 教练
head coach 主教练
football player 足球运动员
referee 裁判
lineman 巡边员
captain / leader 队长
forward / striker 前锋
midfielder 前卫
left midfielder 左前卫
right midfielder 右前卫
attacking midfielder 攻击型前卫（前腰）defending midfielder 防守型前卫（后腰）center forward 中锋
full back 后卫
center back 中后卫
left back 左后卫
right back 右后卫
sweeper 清道夫，拖后中卫goalkeeper / goalie 守门员
cheer team 拉拉队
substitute/ reserve 替补
journalist 记者
ball picker 拾球童
crowd/ fans 球迷
linesman 司线员
足球技术篇
kick-off 开球
bicycle kick / overhead kick 倒钩球chest-high ball 半高球
corner ball / corner 角球
goal kick 球门球
handball 手球
header 头球
penalty kick 点球
place kick 定位球
own goal 乌龙球
hat-trick 帽子戏法
free kick 任意球
direct free kick 直接任意球indirect free kick 间接任意球stopping 停球
chesting 胸部停球
pass 传球
short pass 短传
long pass 长传
cross pass 横传
spot pass 球传到位consecutive passes 连续传球take a pass 接球
triangular pass 三角传球
flank pass 边线传球
lobbing pass 高吊传球
volley pass 凌空传球
slide tackle 铲球
rolling pass / ground pass 地滚球flying header 跳起顶球clearance kick 解围
shoot 射门
close-range shot 近射
long shot 远射
offside 越位
throw-in 掷界外球
block tackle 正面抢截
body check 阻挡
fair charge 合理冲撞
diving header 鱼跃顶球
dribbling 盘球，带球
clean catching （守门员）接高球finger-tip save （守门员）托救球offside 越位
deceptive movement 假动作
break through 突破
kick-out 踢出界
save 扑救
tackle/ hard tackle 拦截/硬朗拦截sliding tackle 铲球
back heel pass 脚后跟传球
man wall 排人墙
trap 控球
chip 削球
fake action 假动作
volley 抽射
dead chick 补射
half-volley 凌空抽射
clear 大脚解围
nutmeg 把球穿过对方两脚之间shielding 用身体保护球obstruction 站在对方带球方向以图抢marking 盯人
足球战术篇
set the pace 掌握进攻节奏
ward off an assault 击退一次攻势break up an attack 破坏一次攻势disorganize the defence 搅乱防守total football 全攻全守足球战术open football 拉开的足球战术
off-side trap 越位战术
wing play 边锋战术
time wasting tactics 拖延战术
4-3-3 formation 433阵型
4-4-2 formation 442阵型
beat the offside trap 反越位成功foul 犯规
technical foul 技术犯规
break loose 摆脱
control the midfield 控制中场
set a wall 筑人墙
close-marking defence 盯人防守
offending 攻击型
defending 防守型
central breakthrough 中央突破
counter attack 反攻
side attack 边线侧击
overlap 叠瓦式助攻
wall pass/ one-two 撞墙式传球
比赛方式篇
half-time interval 中场休息
round robin 循环赛
group round robin 小组循环赛
extra time 加时赛
elimination match 淘汰赛
injury time 伤停补时
golden goal / sudden death 金球制，突然死亡法eighth-final 八分之一决赛
quarterfinal 四分之一决赛
semi-final 半决赛
final match 决赛
preliminary match 预赛
one-sided game 一边倒的比赛
competition regulations 比赛条例disqualification 取消比赛资格
match ban 禁赛命令
doping test 药检
draw / sortition 抽签
装备篇
boot 球鞋jersey 球衣
shorts 短裤stockings 球袜
pad 护具
犯规篇
send a player off 判罚出场
hands 手球
penalty 点球
offside 越位
onside 没有越位
professional/ technical foul 技术犯规
yellow card/ caution/ booking 黄牌警告
red card 红牌
sent off 驱逐离场
goal 球门，进球数
draw 平局
goal drought 进球荒
ranking 排名（名次）
欧洲豪门球场中英文对照
AC米兰圣西罗球场 san siro
国际米兰梅阿查球场 meazza
皇家马德里伯纳乌球场 bernabeu
巴塞罗那诺坎普球场 nou camp
曼联老特拉福德球场old trafford
利物浦安菲尔德球场 anfield
切尔西斯坦福桥球场 stamford bridge
阿森纳酋长/海布里球场emirates /highbury（old）
欧洲十大绿荫豪门
英超(Premiership)
曼联 Manchester United
切尔西Chelsea
利物浦Liverpool
阿森纳Arsenal
西甲(La Liga)
皇马Real Madrid
巴萨Barcelona
意甲(Serie A)
AC米兰AC Milan
国际米兰Inter Milan
尤文图斯Juventus
德甲
拜仁Bayern Muchen
Football, soccer, Association football 足球
field, pitch 足球场
midfied 中场
kick-off circle 中圈
half-way line 中线
football, eleven 足球队
football player 足球运动员goalkeeper, goaltender, goalie 守门员back 后卫
left 左后卫
right back 右后卫
centre half back 中卫
half back 前卫
left half back 左前卫
right half back 右前卫
forward 前锋
centre forward, centre 中锋
inside left forward, inside left 左内锋inside right forward, inside right 右内锋outside left forward, outside left 左边锋outside right forward, outside right 右边锋
kick-off 开球
bicycle kick, overhead kick 倒钩球
chest-high ball 平胸球
corner ball, corner 角球
goal kick 球门球
ground ball, grounder 地面球
hand ball 手触球
header 头球
penalty kick 点球
spot kick 罚点球
free kick 罚任意球
throw-in 掷界外球
ball handling 控制球
block tackle 正面抢截
body check 身体阻挡
bullt 球门前混战
fair charge 合理冲撞
chesting 胸部挡球
close-marking defence 钉人防守
close pass, short pass 短传consecutive passes 连续传球
deceptive movement 假动作
diving header 鱼跃顶球
flying headar 跳起顶球
dribbling 盘球
ball playing skill 控球技术
finger-tip save （守门员）托救球clean catching （守门员）跳球抓好
flank pass 边线传球
high lobbing pass 高吊传球
scissor pass 交叉传球
volley pass 凌空传球
triangular pass 三角传球
rolling pass, ground pass 滚地传球
to pass the ball 传球
slide tackle 铲球
clearance kick 解除危险的球
to shoot 射门
grazing shot 贴地射门
close-range shot 近射
long drive 远射
mishit 未射中
offside 越位
to take a pass 接球
spot pass 球传到位
to trap 脚底停球
to intercept 截球
to break through, to beat 带球过人
to break loose 摆脱
to control the midfield 控制中场
to disorganize the defence 破坏防守to fall back 退回
to set a wall 筑人墙
to set the pace 掌握进攻节奏
to ward off an assault 击退一次攻势to break up an attack 破坏一次攻势
total football 全攻全守足球战术open football 拉开的足球战术
off-side trap 越位战术
wing play 边锋战术
shoot-on-sight tactics 积极的抢射战术time wasting tactics 拖延战术
Brazilian formation 巴西阵式， 4-2-4 阵式
four backs system 四后卫制
four-three-three formation 4-3-3 阵式
four-two-four formation 4-2-4 阵式
red card 红牌（表示判罚出场）
yellow card 黄牌（表示警告）
突破breakthrough 头球抢点是slam a header 抢点突破是什么意思？传球pass
助攻动词可以用feed 名词可以用assist
下底传中cross low
远射long-range
前腰attacking midfielder
盘带dribble 也有短传球的意思
锋线搭挡: The forward line teams up
揭幕赛: First Match
抢点突破: Off the ball
传球: pass
助攻: assist
插上: back push
内切: center attack
下底传中: crossing
远射: long shot
前腰: Attacking Midfielder
盘带: Dribbling
护球: foot work
抢点: Off the ball
锋线搭挡: 没有这个词, 这个是中国人起的锋线就是forward/striker 揭幕赛: First Match
抢点突破: Off the ball
传球: pass
助攻: assist
插上: back push
内切: center attack
下底传中: crossing
远射: long shot
前腰: Attacking Midfielder
盘带: Dribbling
护球: foot work
抢点: Off the ball
足球场
midfield 中场
backfield 后场
kickoff circle / center circle 中圈halfway line 中线
touchline / sideline 边线
goal line 球门线
end line 底线
penalty mark （点球）罚球点
penalty area 禁区（罚球区）
goal area 小禁区（球门区）
球队称谓
coach 教练
head coach 主教练
football player 足球运动员
referee 裁判
lineman 巡边员
captain / leader 队长
forward / striker 前锋
midfielder 前卫
left midfielder 左前卫
right midfielder 右前卫
attacking midfielder 攻击型前卫（前腰）defending midfielder 防守型前卫（后腰）center forward 中锋
full back 后卫
center back 中后卫
left back 左后卫
right back 右后卫
sweeper 清道夫，拖后中卫
goalkeeper / goalie 守门员
cheer team 拉拉队
足球技术
kick-off 开球
bicycle kick / overhead kick 倒钩球
chest-high ball 半高球
corner ball / corner 角球
goal kick 球门球
handball 手球
header 头球
penalty kick 点球
place kick 定位球
own goal 乌龙球
hat-trick 帽子戏法
free kick 任意球
direct free kick 直接任意球indirect free kick 间接任意球stopping 停球
chesting 胸部停球
pass 传球
short pass 短传
long pass 长传
cross pass 横传
spot pass 球传到位
consecutive passes 连续传球
take a pass 接球
triangular pass 三角传球
flank pass 边线传球
lobbing pass 高吊传球
volley pass 凌空传球
slide tackle 铲球
rolling pass / ground pass 地滚球flying header 跳起顶球
clearance kick 解围
shoot 射门
close-range shot 近射
long shot 远射
offside 越位
throw-in 掷界外球
block tackle 正面抢截
body check 阻挡
fair charge 合理冲撞
diving header 鱼跃顶球
dribbling 盘球，带球
clean catching （守门员）接高球finger-tip save （守门员）托救球offside 越位
deceptive movement 假动作
break through 突破
kick-out 踢出界
足球战术
set the pace 掌握进攻节奏
ward off an assault 击退一次攻势
break up an attack 破坏一次攻势
disorganize the defence 搅乱防守
total football 全攻全守足球战术
open football 拉开的足球战术
off-side trap 越位战术
wing play 边锋战术
time wasting tactics 拖延战术
4-3-3 formation 433阵型
4-4-2 formation 442阵型
beat the offside trap 反越位成功
foul 犯规
technical foul 技术犯规
break loose 摆脱
control the midfield 控制中场
set a wall 筑人墙
close-marking defence 盯人防守
比赛方式
half-time interval 中场休息
round robin 循环赛
group round robin 小组循环赛
extra time 加时赛
elimination match 淘汰赛
injury time 伤停补时
golden goal / sudden death 金球制，突然死亡法eighth-final 八分之一决赛
quarterfinal 四分之一决赛
semi-final 半决赛
final match 决赛
preliminary match 预赛
one-sided game 一边倒的比赛
competition regulations 比赛条例disqualification 取消比赛资格match ban 禁赛命令
doping test 药检
draw / sortition 抽签
send a player off 判罚出场
red card 红牌
yellow card 黄牌
goal 球门，进球数
draw 平局
goal drought 进球荒
ranking 排名（名次）
PCB 专业术语中英文翻译 很多PCB 的书上使用的是英文，但是大多数的人又看不懂英文， 这时候怎么办呢，我们需要翻译，但是如果每看到一个不会的词 儿就去翻译，那么就太耗费时间了，所以我们捷多邦总结了一些 常用的专业术语的中英文对照，希望能对大家有用。 1.印制电路：printed circuit 2.印制线路：printed wiring 3.印制板：printed board 4.印制板电路：printed circuit board (pcb) 5.印制线路板：printed wiring board(pwb) 6.印制元件：printed component 7.印制接点：printed contact 8.印制板装配：printed board assembly 9.板：board 1 10.表面层合电路板：surface laminar circuit (slc) 11.埋入凸块连印制板：b2it printed board 12.多层膜基板：multi-layered film substrate(mfs) 13.层间全内导通多层印制板：alivh multilayer printed board 14.载芯片板：chip on board (cob) 15.埋电阻板：buried resistance board 16.母板：mother board 17.单面印制板：single-sided printed board(ssb) 、管路敷设技术通过管线不仅可以解决吊顶层配置不规范高中资料试卷问题，而且可保障各类管路习题到位。在管路敷设过程中，要加强看护关于管路高中资料试卷连接管口处理高中资料试卷弯扁度固定盒位置保护层防腐跨接地线弯曲半径标等，要求技术交底。管线敷设技术中包含线槽、管架等多项方式，为解决高中语文电气课件中管壁薄、接口不严等问题，合理利用管线敷设技术。线缆敷设原则：在分线盒处，当不同电压回路交叉时，应采用金属隔板进行隔开处理；同一线槽内强电回路须同时切断习题电源，线缆敷设完毕，要进行检查和检测处理。、电气课件中调试对全部高中资料试卷电气设备，在安装过程中以及安装结束后进行 高中资料试卷调整试验；通电检查所有设备高中资料试卷相互作用与相互关系，根据生产工艺高中资料试卷要求，对电气设备进行空载与带负荷下高中资料试卷调控试验；对设备进行调整使其在正常工况下与过度工作下都可以正常工作；对于继电保护进行整核对定值，审核与校对图纸，编写复杂设备与装置高中资料试卷调试方案，编写重要设备高中资料试卷试验方案以及系统启动方案；对整套启动过程中高中资料试卷电气设备进行调试工作并且进行过关运行高中资料试卷技术指导。对于调试过程中高中资料试卷技术问题，作为调试人员，需要在事前掌握图纸资料、设备制造厂家出具高中资料试卷试验报告与相关技术资料，并且了解现场设备高中资料试卷布置情况与有关高中资料试卷电气系统接线等情况 ，然后根据规范与规程规定，制定设备调试高中资料试、电气设备调试高中资料试卷技术电力保护装置调试技术，电力保护高中资料试卷配置技术是指机组在进行继电保护高中资料试卷总体配置时，需要在最大限度内来确保机组高中资料试卷安全，并且尽可能地缩小故障高中资料试卷破坏范围，或者对某些异常高中资料试卷工况进行自动处理，尤其要避免错误高中资料试卷保护装置动作，并且拒绝动作，来避免不必要高中资料试卷突然停机。因此，电力高中资料试卷保护装置调试技术，要求电力保护装置做到准确灵活。对于差动保护装置高中资料试卷调试技术是指发电机一变压器组在发生内部故障时，需要进行外部电源高中资料试卷切除从而采用高中资料试卷主要保护装置。
模具英语专业术语 模具述语 一、入水：gate 进入位： gate location 水口形式：gate type 大水口：edge gate 细水口： pin-point gate 水口大小：gate size 转水口： switching runner/gate 唧嘴口径： sprue diameter 二、流道: runner 热流道： hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance 热嘴： hot sprue 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头： connector plug 插座： connector socket 密封/封料： seal 三、运水：water line 喉塞：line lpug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connector plug/socker 四、模具零件： mold components 三板模：3-plate mold 二板模：2-plate mold 边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边L：guide pin 顶针板：ejector retainner plate 托板： support plate 螺丝： screw 管钉：dowel pin 开模槽：ply bar scot 内模管位：core/cavity inter-lock 顶针： ejector pin 司筒：ejector sleeve 司筒针：ejector pin 推板：stripper plate 缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter 模胚（架）： mold base 上内模：cavity insert 下内模：core insert 行位（滑块）： slide 镶件：insert 压座/斜鸡：wedge 耐磨板/油板：wedge wear plate 压条：plate 撑头: support pillar 唧嘴： sprue bushing 挡板：stop plate 定位圈：locating ring 锁扣：latch 扣鸡：parting lock set 推杆：push bar 栓打螺丝：S.H.S.B 顶板：eracuretun 活动臂：lever arm 分流锥：spure sperader 水口司:bush 垃圾钉：stop pin 隔片：buffle 弹弓柱：spring rod 弹弓:die spring 中托司：ejector guide bush 中托边：ejector guide pin 镶针：pin 销子：dowel pin 波子弹弓：ball catch 喉塞: pipe plug
Counter bored hole 沉孔 Chamfer 倒斜角 Fillet 倒圆角 padding block垫块 stepping bar垫条 upper die base上模座 lower die base下模座 upper supporting blank上承板 upper padding plate blank上垫板 spare dies模具备品 spring 弹簧 bolt螺栓 document folder活页夹 file folder资料夹 to put file in order整理资料 spare tools location手工备品仓 first count初盘人 first check初盘复棹人 second count 复盘人 second check复盘复核人 equipment设备 waste materials废料 work in progress product在制品 casing = containerization装箱 quantity of physical inventory second count 复盘点数量 Quantity of customs count 会计师盘,点数量 the first page第一联 filed by accounting department for reference会计部存查 end-user/using unit(department)使用单位 Summary of year-end physical inventory bills 年终盘点截止单据汇总表 bill name单据名称 This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department) 本表请与盘点清册一起送会计部－(NHK厂区送财会部) Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表 blank and waste sheet NO. 空白与作废单号
陶瓷 ceramics 合成纤维 synthetic fibre 电化学腐蚀 electrochemical corrosion 车架 automotive chassis 悬架 suspension 转向器 redirector 变速器 speed changer 板料冲压 sheet metal parts 孔加工 spot facing machining 车间 workshop 工程技术人员 engineer 气动夹紧 pneuma lock 数学模型 mathematical model 画法几何 descriptive geometry 机械制图 Mechanical drawing 投影 projection 视图 view 剖视图 profile chart 标准件 standard component 零件图 part drawing 装配图 assembly drawing 尺寸标注 size marking
技术要求 technical requirements 刚度 rigidity 内力 internal force 位移 displacement 截面 section 疲劳极限 fatigue limit 断裂 fracture 塑性变形 plastic distortion 脆性材料 brittleness material 刚度准则 rigidity criterion 垫圈 washer 垫片 spacer 直齿圆柱齿轮 straight toothed spur gear 斜齿圆柱齿轮 helical-spur gear 直齿锥齿轮 straight bevel gear 运动简图 kinematic sketch 齿轮齿条 pinion and rack 蜗杆蜗轮 worm and worm gear 虚约束 passive constraint 曲柄 crank 摇杆 racker 凸轮 cams
市场营销专业术语中英文对照标准翻译 本文为市场营销中经常用到的一些中文与英文互译的标准用语，希望对市场营销从业人员有所帮助。 《财富》杂志Fortune 案头调研Desk Research 奥美公司Ogilvy & Mather 白色商品White Goods 百乐门Parliament 百威啤酒Budweiser 包裹销售法Banded Pack 宝洁公司Procter & Gamble 宝丽来Polaroid 宝马BMW 边际成本Marginal Cost 边际收益Marginal Benefit 标准差，均差Standard Deviation 别克Buick 波立兹调查公司Alfred Politz Research, Inc 波旁王朝Ancient Age Bourbon 波特福洛分析Portefolio Analysis 产品差异Product Differentiation 产品生命周期Product Life Cycle 产品系列Product Line 产品组合Product Mix 阐述Presentation 超级市场Supermarket 成对比较法Paired Comparisons 成功的理想主义者Successful Idealist 承诺型消费者Committed Buyer 程度测试Tachistoscope 橙色商品Orange Goods 冲动购买Impulse Buying 重叠率Duplication 抽样Sampling 传销Pyramid Selling 传阅发行量Pass-on Circulation 词语联想法Word Associaton 刺激营销Incentive Marketing 促销Promotion 达彼思广告公司Ted Bates & Copany 大卫·奥格威David Ogilvy 戴比尔斯De Beers
模具术语英文翻译
模具术语英文翻译 根据国家标准，以下为部分塑料模具成形术语的标准翻译。 动模 Movable Mould Moving Half 定模座板 Fixed Clamp Plate Top Clamping Plate Top Plate 动模座板 Moving Clamp Plate Bottom Clamping Plate Bottom Plate 上模座板 Upper Clamping Plate 下模座板 Lower Clamping Plate 凹模固定板 Cavity-retainer Plate 型芯固定板 Mould Core-retainer Plate 凸模固定板 Punch-retainer Plate 模套 Die Body Die Sleeve Die Blank 支承板 Backing Plate Support Plate 垫块 Spacer Parallel 支架 Ejector Housing Mould Base Leg 模头 Die Head 根据国家标准，以下为部分压铸模具术语的标准翻译。 压力铸造模具 Die-Casting Die 压铸模零部件 定模 Fixed Die Cover Die 定模座板 Fixed Clamping Plate 定模套板 Bolster Fixed Die 动模 Moving Die Ejector Die 动模座板 Moving Clamping Plate 直流道 Sprue 横流道 Runner 内浇口 Gate 模具分类 Injection Mold 注塑模 Plastic Rubber Mould 塑胶模 Rubber Molding 橡胶成形 Hot Chamber Die Casting 热室压铸 Sand Mold Casting 砂模铸造 Extrusion Mold 挤出模 Multi-Cavity Mold 多模穴模具 Stack Mold, Stack Injection Mould 叠层模
外文翻译 英文原文 Belt Conveying Systems Development of driving system Among the methods of material conveying employed，belt conveyors play a very important part in the reliable carrying of material over long distances at competitive cost．Conveyor systems have become larger and more complex and drive systems have also been going through a process of evolution and will continue to do so．Nowadays，bigger belts require more power and have brought the need for larger individual drives as well as multiple drives such as 3 drives of 750 kW for one belt(this is the case for the conveyor drives in Chengzhuang Mine)．The ability to control drive acceleration torque is critical to belt conveyors’ performance．An efficient drive system should be able to provide smooth，soft starts while maintaining belt tensions within the specified safe limits．For load sharing on multiple drives．torque and speed control are also important consideratio ns in the drive system’s design. Due to the advances in conveyor drive control technology，at present many more reliable．Cost-effective and performance-driven conveyor drive systems cov ering a wide range of power are available for customers’ choices[1]. 1 Analysis on conveyor drive technologies 1．1 Direct drives Full-voltage starters．With a full-voltage starter design，the conveyor head shaft is direct-coupled to the motor through the gear drive．Direct full-voltage starters are adequate for relatively low-power, simple-profile conveyors．With direct fu11-voltage starters．no control is provided for various conveyor loads and．depending on the ratio between fu11- and no-1oad power requirements，empty starting times can be three or four times faster than full load．The maintenance-free starting system is simple，low-cost and very reliable．However, they cannot control starting torque and maximum stall torque；therefore．they are
常用模具零件中英文对照表 2005-12-19 14:51:17???中国注塑网 入水：gate 进入位：gate location 水口形式：gate type 大水口：edge gate 细水口： pin-point gate 水口大小：gate size 转水口：switching runner/gate 唧嘴口径：sprue diameter 二、流道: runner 热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis :?[??n?l?s?s] 流道平衡:runner balance 热嘴：hot sprue 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头：connector plug 插座： connector socket 密封/封料： seal 三、运水：water line 喉塞：line lpug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connector plug/socker 四、模具零件：mold components 三板模：3-plate mold 二板模：2-plate mold 边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边：guide pin 顶针板：ejector retainer plate 托板：support plate
机械术语英文翻译 阿基米德蜗杆Archimedes worm 安全系数safety factor; factor of safety安全载荷safe load 凹面、凹度concavity扳手wrench 板簧flat leaf spring 半圆键woodruff key 变形deformation摆杆oscillating bar 摆动从动件oscillating follower 摆动从动件凸轮机构cam with oscillating follower 摆动导杆机构oscillating guide-bar mechanism 摆线齿轮cycloidal gear摆线齿形cycloidal tooth profile 摆线运动规律cycloidal motion 摆线针轮cycloidal-pin wheel包角angle of contact 保持架cage背对背安装丨back-to-back arrangement 背锥back cone ；normal cone 背锥角back angle背锥距back cone distance比例尺scale 热容specific heat capacity 闭式链closed kinematic chain闭链机构closed chain mechanism 臂部arm 变频器frequency converters变频调速frequency control of motor speed 变速speed change 变速齿轮change gear ; change wheel变位齿轮modified gear变位系数modification coefficient 标准齿轮standard gear标准直齿轮standard spur gear 表面质量系数superficial mass factor 表面传热系数surface coefficient of heat transfer 表面粗糙度surface roughness 并联式组合combination in parallel并联机构parallel mechanism 并联组合机构parallel combined mechanism并行工程concurrent engineering 并行设计concurred design, CD不平衡相位phase angle of unbalance 不平衡imbalance (or unbalance)不平衡量amount of unbalance 不完全齿轮机构intermittent gearing波发生器wave generator 波数number of waves补偿compensation 参数化设计parameterization design, PD残余应力residual stress 操纵及控制装置operation control device槽轮Geneva wheel 槽轮机构Geneva mechanism ；Maltese cross槽数Geneva numerate 槽凸轮groove cam侧隙backlash 差动轮系differential gear train差动螺旋机构differential screw mechanism 差速器differential常用机构conventional mechanism; mechanism in common use 车床lathe承载量系数bearing capacity factor 承载能力bearing capacity成对安装paired mounting 尺寸系列dimension series齿槽tooth space 齿槽宽spacewidth齿侧间隙backlash 齿顶高addendum齿顶圆addendum circle 齿根高dedendum齿根圆dedendum circle 齿厚tooth thickness齿距circular pitch 齿宽face width齿廓tooth profile 齿廓曲线tooth curve齿轮gear 齿轮变速箱speed-changing gear boxes齿轮齿条机构pinion and rack 齿轮插刀pinion cutter; pinion-shaped shaper cutter齿轮滚刀hob ,hobbing cutter 齿轮机构gear齿轮轮坯blank 齿轮传动系pinion unit齿轮联轴器gear coupling 齿条传动rack gear齿数tooth number 齿数比gear ratio齿条rack 齿条插刀rack cutter; rack-shaped shaper cutter齿形链、无声链silent chain 齿形系数form factor齿式棘轮机构tooth ratchet mechanism 插齿机gear shaper重合点coincident points 重合度contact ratio冲床punch
DFM常用中英文对照 1、这个红色面在前模方向/后模方向/行位方向有倒扣。 This red surface is undercut at cavity side / core side / slider side. 2、这些红色面在前模方向/后模方向/行位方向有倒扣。 These red surfaces are undercut at cavity side / core side / slider side. 3、产品的这个位置太小，导致模具在前模方向/后模方向/行位方向有薄钢位。 This position is too small and it will bring the thin steel at cavity side / core side / slider side. 4、这些红色线是前后模/镶件/行位/斜顶分型线。 These red lines are the parting line of cavity and core / insert / slider / lifter. 5、此产品使用推板/推块顶出。 Use the stripper plate / ejector block to eject this part. 6、前模/后模斜内行位。 Inner angle slider at cavity / core side. 7、为了简化模具结构建议改变此处出模方向。 Suggest to change the draft direction of this position to make the mold structure simply. 8、最终的进胶位置根据模流分析。 Finally gate position according the mold flow analysis. 9、斜顶与后面的柱位空间太小，斜顶在运动时会干涉到柱子，请考虑移动这个柱子的位置。 This lifter intervene with the pole during ejection, please consider changing the position of the pole. 10、此处有薄钢位，强度不足而且不容易冷却。 The strength of this area is too weak and it is hard to cool because the thin steel. 11、此处有尖角，填充困难。 It is hard to fill for this area because the sharp feature. 12、此处料位太厚，会有缩水，建议减胶改善。 We suggest to reduce some wall thickness to avoid the sink mark for this position. 13、此处的行位夹线在外观面上，请确认是否接受？ Please confirm whether it is acceptable to have a slider line on the visible surface? 14、建议加大拔模角，以便脱模顺利。 We suggest to enlarge the draft angle to help release the tool. 15、如果分型面此处，模具上会有尖角和刀口，对模具寿命有影响。 There are sharp edges if we set the parting line here, it will reduce the tool life. 16、此处料厚段差很大，成品表面会有应力痕，建议修改如图示。 The thickness is not equal and it will bring the stress lines on the surface, suggest to improve the part as the picture shown. 17、此大行位上有小行位，开模时小行位需先退，大行位做延时，合模时则相反。 The small slider is inside the big slider, when the mold open, the small slider need to recede first and the big slider have to postpone. When the mold close, it is contrary. 18、此处需做强顶。 This position need to force ejection. 19、由于此处没有足够空间下热咀，所以需做一个柱子进胶。 This position need to make a pole for gating because there have no enough space for hot sprue. 20、沾模， stick
预约券reservation ticket 下午茶high tea 微博Microblog/ Tweets 裸婚naked wedding 亚健康sub-health 平角裤boxers 愤青young cynic 灵魂伴侣soul mate 小白脸toy boy 精神出轨soul infidelity 人肉搜索flesh search 剩女3S lady（single，seventies,stuck）/left girls 山寨copycat 异地恋long-distance relationship 性感妈妈yummy mummy 钻石王老五diamond bachelor 时尚达人fashion icon 上相的,上镜头的photogenic 学术界academic circle 哈证族certificate maniac 偶像派idol type 住房公积金housing funds 熟女cougar（源自电影Cougar Club） 挑食者picky-eater 伪球迷fake fans 紧身服straitjacket 团购group buying 奉子成婚shotgun marriage 婚前性行为premarital sex 炫富flaunt wealth 决堤breaching of the dike 上市list share 赌球soccer gambling 桑拿天sauna weather 自杀Dutch act 假发票fake invoice 金砖四国BRIC countries 笑料laughing stock 泰国香米Thai fragrant rice 学历造假fabricate academic credentials 泄洪release flood waters 狂热的gaga eg: I was gaga over his deep blue eyes when I first set eyes on him 防暑降温补贴high temperature subsidy 暗淡前景bleak prospects
机械专业相关词汇中英文翻译大全 单价unit price 工日合计Man-day total/work-day total 人工费cost of labor 材料费materials expenses 机械的mechanical 检查接线connection test 发电机generator 调相机phase regulator 周波cycle 减负荷装置 load-shedding equipment 断路器柜circuit breaker cabinet 单母线single busbar 互感器transformer 每相电流Current by Phase 封闭式插接close type socket joint 发电机控制面板generator control panel 分级卸载sorted unloading 同步控制synchronization control 调速器 speed governor 信号屏signal screen 继电器relay 高压柜high pressure cabinet 油浸电力变压器oil-immersed power transformer 空气断路器air circuit breaker 控制屏control panel 直流馈电屏direct current feed control panel 电容器electric condenser 计量盘metering panel 成套配电箱whole set of distribution box 落地式floor model 控制开关Control switches 铜芯电力电缆Copper core power cable 控制电缆actuating cable 热缩式电力电缆终端头pyrocondensation power cable terminal 钢结构支架配管steel structure bracket tubing 万用槽钢versatile U-steel 电缆托架 cable bracket 钢制托盘式桥架steel Tray-type cable support system waterproof socket 防水插座 防爆插座Explosion-proof socket 接地绞线earthing twisted pair 接地母线 earthing bus
模具名词中英文对照表序号中文名英文名 1一、水口gate 2进水位gate location 3水口形式gate type 4大水口edge gate 5细水口pin-point gate 6水口大小gate size 7转水口switching gate 8唧嘴口径sprue diameter 9二、流道runner 10热流道hot runner 11冷流道cold runner 12唧嘴直流direct sprue gate 13圆形流道round runner 14模流分析mold flow analysis 15流道平衡runner balance 16热嘴hot sprue 17热流道板hot manifold 18发热管cartridge heater 19探针thermocouples 20插头connector plug 21插座connector socket 22密封/封料seal 23三、运水water line 24喉塞line pug 25喉管tube 26塑胶管plastic tube 27快速接头jiffy quick connector plug 28四、模具零件mold components 29三板模three-plate mold 模具名词中英文对照表 序号中文名英文名 30二板模two-plate mold 31边钉/ 导边leader pin /guide pin
32边司/ 导套bush in g/guide bush ing 33顶针板ejector retainer plate 34托板support plate 35螺丝screw 36管钉dowel pin 37开模槽ply bar score 38内模管位core/cavity inter-lock 39顶针ejector pin 40司筒ejector sleeve 41司筒针ejector pin 42推板stripper plate 43缩呵movable core 44扣机（尼龙拉勾）n yl on latch lock 45斜顶lifter 46模胚（架）mold base 47母模cavity in sert 48公模core insert 49行位（滑块）slide 50 镶件in sert 51压座/斜鸡wedge 52耐磨板/ 油板wedge wear plate 53压条plate 54撑头support pillar 55唧嘴sprue bushing 56挡板stop plate 57定位圈locating ring 58锁扣latch 模具名词中英文对照表 序号中文名英文名 59扣鸡parti ng lock set 60推杆push bar 61栓打螺丝S.H.S.B 62顶板ejector plate 63活动臂lever arm
机械专业英语词汇 陶瓷ceramics 合成纤维synthetic fibre 电化学腐蚀electrochemical corrosion 车架automotive chassis 悬架suspension 转向器redirector 变速器speed changer 板料冲压sheet metal parts 孔加工spot facing machining 车间workshop 工程技术人员engineer 气动夹紧pneuma lock 数学模型mathematical model 画法几何descriptive geometry 机械制图Mechanical drawing 投影projection 视图view 剖视图profile chart 标准件standard component 零件图part drawing 装配图assembly drawing 尺寸标注size marking 技术要求technical requirements 刚度rigidity 内力internal force 位移displacement 截面section 疲劳极限fatigue limit 断裂fracture 塑性变形plastic distortion 脆性材料brittleness material 刚度准则rigidity criterion 垫圈washer 垫片spacer 直齿圆柱齿轮straight toothed spur gear 斜齿圆柱齿轮helical-spur gear 直齿锥齿轮straight bevel gear 运动简图kinematic sketch 齿轮齿条pinion and rack 蜗杆蜗轮worm and worm gear 虚约束passive constraint 曲柄crank
1. The undercut area where interfere with slide block need to be filled material to help the slide can move smoothly.（和滑塊干涉的倒勾請加料填平至滑塊可以順利滑動） 2. The thickening added too thick.(加肉太多) 3. The thickening area is too wide.（加肉面積太大） 4. Gate position is moved.(GATE位置移位) 5. The split line of slide block or the area of slide.(滑塊拆的位置) 6. This area is hard to be filled due to the sharp feature(此處有尖角，填充困難) 7. The strength of this area is too weak and isn’t easy to get c old due to the steel too thin. 8. ( 此處鋼材太薄，強度不足而且不容易冷卻) 9. .The semicircle of cylinder avoids designing on slide block lest it will be pulled apart or cause drag mark. 10. ( 圓柱特徵要有一半圓不可以拆在滑塊上，以免粘滑塊造成拉白，拉斷.) 11. The part will be damaged if we make lifter in this area. 12. ( 此處做斜銷在作動時會削到成品肉厚) 13. This is critical surface where is not allow to add material. 14. ( 這個面是裝配面，不能加料) 15. This thick wall area might because sink mark,Please reduce some wall thickness to improve it.) 16. ( 此處料位太厚，會有縮水，建議減料改善) 17. Please confirm whether it is critical surface or not. Please confirm whether it is acceptable to has Slide split line if we have slide in this area. 18. （此面是不是外觀面，此處做滑塊的話會有結合線，是否可以接受） 19. Please confirm whether we can reduce material to the area where have undercut as indicated to have shut off on core and cavity side. No slide block and lifter to be made. 20. （此處有倒勾，能否減料，使公母模靠破，不做滑塊和斜銷） 21. Please confirm the issues of Parting line, Gate position...Etc otherwise the lead-time will be extended. 22. （請盡快確認這種拆模方式和結構，否則會影響模期） 23. The trim mark of the gate is not visual after open the top case if the gate position is design ed like it 24. （GATE做在此處的話.蓋子打開後看不到GATE的修剪部位） 25. We would suggest to enlarging draft to help tool released.) 26. 加大拔模角，以便脫模順利） 27. There are sharp edges if set the parting line at here, It will reduce the tool life 28. （P.L面開在此處，模具上會有尖角和刀口，對模具壽命有影響） 29. If you insist that the gate position have to be as original design then we would