accessory 附件accompany 陪伴,伴奏actuate 开动,促使adaptation 改进adhesion 附着
adhesive 带粘性的,胶黏adjustment tab 调整垫片aerodynamics 空气动力学affected 受到影响的
air compressor 空气压缩机airbag 安全气囊aircraft carrier 航空母舰aircraft 飞机
air-filled 充入
alert 警报
alkline fuel cell 碱性燃料电池
alkline 碱的
alternator 交流发电机amplify 放大,增强anode 阳极
anti-lock braking system 防抱死系统
appropriate 适当的approximately 近似地,大约asbestos 石棉
assist 援助,帮助
At various angles 以不同的角度
atmospheric 大气的attendant 伴随的
audio 音响,声音automatic adjustment 全自动调节
automotive air conditioning system 汽车空调系统auxiliary 辅助的availability 有效,可得到的人
axle beam 前桥梁
ball nut 循环球螺母
Ball joint 球头节
battery electric vehicle 蓄电池电动车battery pack 电池组
battery 蓄电池
BDC 下止点
Be free to move up and down
自由上下活动
Bead 胎边
bearing 轴承
body 车身
boiling 沸腾的
bonded 粘合而成的
boost 促进,增加
Brace 曲柄
brake backing plate 制动器
底盘
brake caliper 制动钳
brake clearance 制动间隙
brake cylinder 制动缸
brake deviation 制动跑偏
brake drum 制动鼓
brake fade 降低制动效率
brake judder 制动震颤
brake line 制动管路
brake lining 刹车衬片
brake pedal 制动踏板
brake performance 制动
性能
brake shoe 刹车蹄片
brake warning light 制动
报警灯
brake 刹车
braking distance 制动距离
branch 分支
bumper 保险杆
bushing 衬套
by-product 副产品
camshaft 凸轮轴
capacitor 电容器
capacity 能力,容量
carburetor 化油器
carburetor 汽化器,化油器
cathode 阴极
central electronic unit
中心电子设备
central fuel injection 中央
燃油喷射
centralized 集中的
centrifugal blower 离心式
鼓风机
charger 充电器
chassis 底盘
check valve 止回阀
chlorine 氯
Chuck 夹紧
clutch 离合器
coach 长途汽车
coasting 滑行
coefficient 系数
coil springs 螺旋弹簧
coil 线圈
collision 碰撞,冲突
Combat tire 战车用轮胎
combined hybrid 混联式混
合动力
combustion chamber燃烧室
commonplace 平常的东西,
平常的
comparably 可比较的
complement 辅助
complexity 复杂
compresser 压缩机
computer-controlled
automatic adjustment 微机
可控自动调节
condenser 冷凝器
condenser fan 冷凝风扇
configure 配置
connecting rod 连杆
connectors 连接器,连接件
console 控制台
contamination 玷污,污染,
污染物
control agencies 操纵机构
control mechanism 操纵
机构
convertible body 活顶车
cooling 冷却
Cord 绳索
crank 曲柄
crankshaft 曲轴
critical 决定性的
crushing 巡行,常速行驶cylinder block 缸体cylinder head 气缸盖cylinder 圆筒,气缸
dash 仪表板deficiency 缺乏degradation 退化depresss 踩下,压下detour 绕道
differential 差速器
dipstick 机油尺disastrous 损失惨重的disc 圆板,圆盘,制动盘disc brake 盘式制动器disc rotor 制动盘,盘形转子disposal 处理,消除,销毁distributor 分电器dominant 主要的
drag link 转向直拉杆drag link 转向拉杆
drive shaft 传动轴
drop arm 转向垂臂drum brake 鼓式制动器dual 双的,二重的durability 持久性dynamics 动力学ecological 生态的electric motor 电动机electrical system 电气系统electrify 使电气化,使充电electrochemical 电化学的electrolyte 电解质electron 电子
electronic fuel injection (EFI)电控燃油喷射eliminate 减少
emission-control system 排放控制系统
end play 轴向(纵向)间隙energy density 能量密度engine compartment 发动
机舱
engine rotational speed table
发动机转速表
engine 发动机
essential 本质的,实质的
ethanol fuel cell 乙醇燃料
电池
ethanol 乙醇
evaporator 蒸发器
exceptionall特别地,格外地
exert 施加压力
exhaust 排气
expand 使膨胀,扩张
expansion valve 膨胀阀
feedback 反馈,反应
fender 防卫物,挡泥板
final shaft 驱动轴
fixed caliper 固定式制动钳
flatbed 有平台可卸货的
卡车
Flex 弯曲
flexibility 灵活性
flexible joint 挠性连接,
挠性接头
floating caliper 浮钳,定钳
flywheel gear ring 飞轮齿圈
foot-operate 脚操作
for safety 为安全起见
forefront 最前部的
forklift 铲车
forth and back 前后的,来回
的
fossil fuel 矿物燃料
friction 摩擦,摩擦力
Front-end sheet-metal 前悬
金属板
fuel economy 燃油经济性
fuel tank 油箱
fuse 保险丝,导火线
gasket 垫圈,衬垫
gasoline engine direct
injection 缸内直喷
gauge 量表
gear sector 扇形齿轮
gearbox 变速箱
generator 发电机,发生器
geometry 几何学
Give 弯曲;有弹性
golf cart 高尔夫球车
golfer 打高尔夫的人
grid 栅极
groove 沟槽
ground 接地,搭铁
hand brake 手制动器
heat engine 热机
heater radiator 暖风散热器
highly machined surface 精
加工表面
hill climbing 爬坡
hood 车棚,引擎罩
horn 喇叭
Hump 凸起
hybrid electric vehicle 混合
动力车
hydraulic control unit 液
压控制装置
hydraulic lifter 液压挺住
hydrocarbon 碳氢化合物
hydrogen fuel cell 氢燃料电
池
hydrogen 氢
idle valve 怠速阀
ignition key 点火开关
ignition wires 点火线圈
ignition 点火,点燃
illumination
照明,阐明,启发
impacted cover 压紧盖
Impose 将……强加于
In use 通用
Independent front suspension
独立前悬架
indispensable 不可缺少的
inflame 燃烧物
Inflate 使充气
inhibit 抑制,阻止
inlet 进口
Inner tube 内胎instrument panel 仪表板intake 通风口,进气interconvert 互变
interfuse 混入,混合intermediate 中级的,中间的
internal combustion engine 内燃机
Interpose 插入
intersect 相交交叉Irregularity 例外
judder 急剧的变化,颤抖kinetic energy 动能kinetic 运动的
king pin 主销
leaf springs 磨片弹簧
leak 漏洞。使泄露Locate 位于
lock up 锁住locomotive 机动车
lug 拖
luggage compartment行李箱malfunction 故障mass-produced 大批量生产master cylinder 制动主缸,制动总泵
mechanism 机械装置,构造media 媒体,媒质membrane 薄膜
methanol fuel cell 甲醇燃料电池
methanol 甲醇
milk float 送牛奶的马车minimize 将……减到最少modification 修正modulation 调节
module 模数,模块monitor 监控motorcycle 摩托车
multiply 增加,乘multi-point injection 多点喷射
navigation 导航,领航needle bearing 球针轴承
negative electrode 负极
niche 适当的位置
non-separated 非独立的
nuclear reactor核反应堆
nuclear submarine 核潜艇
odometer 里程表
oil drain plug 机油放油
塞
oil filler cap 机油加油口盖
oil sealed board 机油密封板
oil strainer 机油滤网
one-way 单行道的
outlaw 宣布为不合法的
outlet 出口,出路
overhaul 彻底检查,大修
overhead 在头上的,高架的
overload 超载
oversee 监督
overtake 赶上
oxidant 氧化剂
oxygen 氧
pad 摩擦衬块
parallel hybrid 并联式混合
动力
parking brake system 驻车
制动系统
pedestrian 行人
performance 效能,性能
perpendicular 垂直的,正交
的垂线
pick-up screen 集滤器
pinion 小齿轮
piston pin 活塞销
piston 活塞
pitman arm 转向摇臂
plug 电插头
Pneumatic 汽胎
pollutant 污染物质
Polyester 聚酯纤维
positive electrode 正极
potential 潜力
power brake booster
制动助力器
power steering system 动力
转向系
preliminary 预备的,初
步的
propulsion power 推动力
propulsion 推进
proton 质子
pulsation 跳动,有节
奏的跳动
puncture 小孔,轮胎穿孔
rack 使痛苦,绞尽脑汁
rack 齿条
rack-and-pinion steering 齿
轮齿条式转向系
radiator 散热器,冷却器
Rayon 人造丝
reactant 反应物
receiver drier 干燥器
recharge 再充电
recirculating-ball steering 循
环球是转向系
referred to 查阅,提到
refrigeration 制冷,冷藏
regenerative braking 再生制
动,反馈制动
regulate 管制,控制
relay 继电器,
中继转播
release 放开,释放
reliability 可靠性
replenish 补充
resistance 阻力
respiratory 呼吸的
retractor 牵引器
ridge 山脊,脊状突起
rigidity 刚性,硬度
Rim 轮辋
riveted 铆接的
road feel 路感
roof panel 车顶板
rotation 旋转
rotor 转子,转动体
rub 摩擦
rubber 橡皮,橡胶sarter motor 起动机scooter 踏板车
seal 封条密封sector 扇齿
Secure 安全的
sedan 小轿车separated 独立的series hybrid 串联式混合动力
service brake system 行车制动系统
shock 震动,冲击shoe 制动蹄片
side force coefficient 侧力系数
side play 侧隙sideways 一旁的,向侧面的significantly 意味深长的single-function 单功能的single-point injection 单点喷射
siphon 用吸管吸出或排出Skid 打滑
slipping 渐渐松弛的slope 斜坡,斜面,倾斜slow down 减速,缓刑solar panel 太阳能电池板Solid tire 实心轮胎spark plug 火花塞
specify 指明,规定speed sensor 速度传感器spiral cable 螺旋线路spongy 像海绵的,柔软的spool valve 短管阀,伺服阀,方形阀,随动阀spring 弹簧
stability 稳定性standstill 停顿
state of charge 充电状态steady 稳固的,稳定的steam turbine 汽轮机
steep 陡峭的,陡直的steering arm 转向摇臂steering box 转向器壳体
steering column 转向柱
steering gear 转向器
steering gear shaft 转向盘轴
steering knuckle arm 转向
节臂
steering pivot pin 转向节主
销
steering shaft 转向轴
steering stub axle 转向节轴
steering system 转向系统
steering wheel 转向盘
steering 操纵,掌舵,指导
step 踏
streetcar 路面电车
stroke 冲程
Strut rod 摇摆臂
submarine 潜水艇
substantial 大量的,基本的
supplemental restraint
system 辅助约束系统,安
全气囊系统
surge 巨涌,汹涌
suspension 悬架
SUV 多用途赛车
Swing 摆动
swivel 旋转
synergy 增效,协同,配合
TDC 上止点
tension eccentric-pulley 张
紧偏心轮
terrain 地域
the adhesive force 附着力
the intake manifold throttle
进气歧管
thermal 热的,热量的
thread 螺纹
throttle body injection
节气门体喷射
tie rod 转向横拉杆
tightening screw 紧固螺钉
timing gear 正时齿轮
tipper 翻斗卡车
Tire 轮胎
torsion bars 扭力杆
Torsion-bar spring扭杆弹簧
Tower 支架
toxicity 毒性
track rod 转向横拉杆
Traction 牵引力
tractor 拖拉机,牵引车
tram 有轨电车,缆车
transmission system 传动系
统
transport 运输,运送
Transversally 横向的
trigger 触发
trolley pole 接电杆
trolleybus 无轨电车
Tubeless tire 无内胎的
undergo 经历,遭受
Upper and lower control arm
上下控制臂
vacuum booster真空助力器
vacuum solenoid 真空电
磁阀
vacuum真空
valve 阀,气门
ventilation 空气流通
via 凭借
Via a pivot arrangement 通
过驱动轴
vibration 震动
warehousing 入仓库储存
wear 磨损
Wheel spindle 轮轴
wheel cylinder 制动轮缸
Wheel rim 轮辋
windmill 风车
windshield 挡风玻璃
wire harness 电线夹
With respect to就……而
言
withstand 抵挡,经受住
worm gear 蜗轮齿轮
worm 蜗杆,螺纹
wrecked 失事的
第一章汽车总论 1)Today’s average car contains more than 15,000 separate, individual parts that must work together. These parts can be grouped into four major categories: body, engine, chassis and electrical equipment 。P1 现在的车辆一般都由15000多个分散、独立且相互配合的零部件组成。这些零部件主要分为四类:车身、发动机、底盘和电气设备。 2)The engine acts as the power unit. The internal combustion engine is most common: this obtains its power by burning a liquid fuel inside the engine cylinder. There are two types of engine: gasoline (also called a spark-ignition engine) and diesel (also called a compression-ignition engine). Both engines are called heat engines; the burning fuel generates heat which causes the gas inside the cylinder to increase its pressure and supply power to rotate a shaft connected to the power train. P3 发动机作为动力设备,常见的类型是内燃机,其原理是通过发动机缸内的液体燃料燃烧而产生能量。发动机可分为两类:汽油机(点燃式)和柴油机(压燃式),都属于热力发动机。燃料燃烧产生热量使缸内气压上升,产生的能量驱动轴旋转,并传递给动力传动系。 第二章内燃机 1)Power train system: conveys the drive to the wheels 2)Steering system: controls the direction of movement 3)Suspension system: absorbs the road shocks 4)Braking system: slows down the vehicle P4 传动系把发动机输出的扭矩传递给驱动轮。传动系包括离合器(对应机械变速器)或液力变矩器(对应液力自动变速器)、变速器、驱动轴、主减速器、差速器和驱动桥。 5)Drum brakes have a drum attached to the wheel hub, and braking occurs by means of brake shoes expanding against the inside of the drum. With disc brakes, a disc attached to the wheel hub is clenched between two brake pads. P6 鼓式制动器的制动鼓和轮毂连接,制动蹄张开压紧制动鼓内侧从而产生制动。在盘式制动器上,连着轮毂的制动盘被紧紧夹在两个制动块之间。 1)Linking the piston by a connecting rod to a crankshaft causes the gas to rotate the shaft through half a turn.The power stroke"uses up"the gas,so means must be provided to expel the burnt gas and recharge the cylinder with a fresh petrol-air mixture:this control of gas movement is the duty of the valves;An inlet valve allows the mixture to enter at the right time and an exhaust valve lets out the burnt gas after the gas has done its job . P10 活塞通过连杆和曲轴连接,使得气体带动曲轴旋转半圈。作功冲程耗尽了所有的气体,这样就必须采取相应的措施排出废气并且向气缸内充入新的可燃混合气:气体的运动由气门来控制。进气门使可燃混合气在恰当的时刻进入气缸,排气门使燃烧后的废气排出气缸。 2)The spark-ignition engine is an internal-combustion engine with externally supplied in ignition,which converts the energy cntained in the fuel to kinetic energy.The cycle of operations is spread over four piston strokes. To complete the full cycle it takes two revolutions of the crankshaft. P11 火花点火式发动机是由外部提供点火的内燃机,从而将含在燃料内的能量转化成动能。发动机的一个工作循环分布在活塞的四个行程中,一个完整的工作循环曲轴需要转动两圈。 3)The oil pump in the lubricating system draws oil from the oil pan and sends it to all working parts in the engine. The oil drains off and runs down into the pan. Thus,there is constant circulation of oil between the pan and the working parts of the engine. P15
汽车专业英语大纲内部编号:(YUUT-TBBY-MMUT-URRUY-UOOY-DBUYI-0128)
《汽车专业英语》课程标准 学时/学分: 32/2 课程类型:理论课程(A类) 适用专业:汽车电子技术专业 课程所属系部:汽车工程系 批准日期:2014年5月 一、制定依据与课程定位 (一)制定依据 本课程标准是依据汽车检测与维修技术、汽车制造与装配技术、需要制定。 (二)课程定位 《汽车专业英语》这门课程是汽车专业的一门专业选修课程,旨在使学生掌握汽车专业常用的英语词汇。 通过本课程的学习,培养学生在汽车专业领域具有的一定的英语阅读能力和翻译能力,以便学生更好的直接从外文资料中获取新的知识和信息。 二、课程教学目标 《汽车专业英语》是三年制高职汽车检测与维修技术、汽车制造与装配技术、的专业选修课程。其任务是使学生一方面可以巩固已掌握的词汇和语法知识,另一方面扩大专业词汇量,提高学生对汽车专业英文文献的阅读能力。通过教学应使学生获得初步具备专业英语翻译能力和初步具备能够直接从外文资料中获取信息的能力。 (一)知识目标 1、掌握专业英语中的基本词汇和专有名词; 2、掌握专业英语中常用的语法和句型结构; 3、可以阅读有一定词汇量的专业英语文献。 (二)能力目标 通过对《汽车专业英语》的教学,力求向学生提供未来工作岗位所需要专业英语知识,培养学生在实际工作岗位上运用汽车专业英语的能力。
1、阐述“专业阅读”,内容力求反应汽车专业方面的最新知识,文章能展示 当今汽车专业方面的最新技术,同时书中附带一些真实的现场照片。 2、阐述“专业术语”,帮助学生了解汽车各零部件的功能及应用,是学生进 入企业后应用较多的内容。 3、阐述“试试您的动手能力”,以汽车故障诊断为主,列举大量贴近企业工 作实际的实例。 4、阐述“交际会话”,选用贴近实际,贴近企业,贴近岗位的常用专业英语 会话。 (三)素质目标 通过教学应使学生认识《汽车专业英语》学习的基本方法, 1、具备通过查阅资料等方法,通过自学获取知识和新技术的能力; 2、通过不同形式的探究活动、自主学习,体验科技发现和创造的历程,发展 抽象思维和辨证逻辑思维。 3、养成严谨求实的科学态度以及质疑和独立思考的学习习惯。 4、使学生具备正确的价值观与评定事物的能力,具备一定的英文语言表达能 力以及与人交往沟通的能力。 5、培养学生爱岗敬业、团结协作、吃苦耐劳的职业精神与创新设计的意识。? 三、课程内容设计 (一)学时分配
About car engine Of all automobile components,an automobile engie is the most complicated assembly with dominant effects on the function of an autombile.So, the engine is generally called the"heat"of an automobile. 在汽车的所有部件中,汽车发动机是最复杂的组件,其对整车性能有着决定性的作用。因而发动机往往被称作发动机的“心脏”。 There are actually various types of engines such as electric motors,stream engines,andinternal combustion engines.The internal combustion engines seem to have almost complete dominance of the automotive field.The internal combustion engine,as its name indicates,burns fuel within the cylinders and converts the expanding force of the combustion into rotary force used to propel the vehicle. 事实上,按动力来源分发动机有很多种,如电动机、蒸汽机、外燃机等。然而内燃机似乎在发动机领域有着绝对的统治地位。就像其字面意思一样,内燃机的染料在气缸内燃烧,通过将燃烧产生气体的膨胀力转换成转动力来驱动发动机前进。 Engine is the power source of the automobile.Power is produced by the linear motion of a piston in a cylinder.However,this linear motion must be changed into rotary motion to turn the wheels of cars or trucks.The puston attached to the top of a connecting rod by a pin,called a piston pin or wrist pin.The bottom of the connecting rod is attached to the crankshaft.The connecting rod transmits the up-and-down motion of the piston to the crankshaft,which changes it into rotary motion.The connecting rod is mounted on the crankshaft with large bearings called rod bearing.Similar bearings, called main bearings,are used to mount the crankshaft in the block. 发动机是整部车的动力来源。能量来自于活塞在气缸内的(往复)直线运动。然而这种(往复)直线运动必须要转换成旋转运动才能驱动车轮。活塞与连杆通过一个销来连接,这个销称为活塞销。连杆的下部连接于曲拐。连杆把活塞的上下往复运动传递给曲拐,从而将往复直线运动转变成旋转运动。连杆和曲拐的连接使用大的轴承,称之为连杆轴承,类似的轴承也用于将曲轴连接到机体,称之为主轴承。 They are generally two different types of cooling system:water-cooling system and air-cooling system.Water-cooling system is more common.The cooling medium, or coolant, in them is either water or some low-freezing liquid, called antifreeze.A water-cooling system consists of the engine water jacket, thermostat, water pump, radiator, radiator cap, fan, fan drive belt and neccessary hoses. 主要有两种类型的冷却系统:水冷和风冷。水冷系统更为普遍。系统所用冷却介质或是冷却液常委水或其他低凝固点液体,称为抗凝剂。一个完整的水冷系统包括机体水套,节温器,水泵,散热器,散热器罩,风扇,风扇驱动皮带和必需的水管。 A water-cooling system means that water is used as a cooling agent to circulate through the engine to absorb the heat and carry it to the radiator for disposal.The ebgine is cooled mainly through heat transfer and heat dissipation.The heat generated by the mixture burned in the engine must be transferred from the iron or aluminum cylinder to the waterin the water jacket.The outside of the water jacket dissipates some of the heat to the air surrounding it, but most of the heat is carried by the cooling water to the radiator for dissipation.When the coolant temperature in the system reaches 90°,the termostat valve open fully, its slanted edge shutting off
汽车专业英语大纲 Company number:【0089WT-8898YT-W8CCB-BUUT-202108】
《汽车专业英语》课程标准 学时/学分: 32/2 课程类型:理论课程(A类) 适用专业:汽车电子技术专业 课程所属系部:汽车工程系 批准日期:2014年5月 一、制定依据与课程定位 (一)制定依据 本课程标准是依据汽车检测与维修技术、汽车制造与装配技术、需要制定。 (二)课程定位 《汽车专业英语》这门课程是汽车专业的一门专业选修课程,旨在使学生掌握汽车专业常用的英语词汇。 通过本课程的学习,培养学生在汽车专业领域具有的一定的英语阅读能力和翻译能力,以便学生更好的直接从外文资料中获取新的知识和信息。 二、课程教学目标 《汽车专业英语》是三年制高职汽车检测与维修技术、汽车制造与装配技术、的专业选修课程。其任务是使学生一方面可以巩固已掌握的词汇和语法知识,另一方面扩大专业词汇量,提高学生对汽车专业英文文献的阅读能力。通过教学应使学生获得初步具备专业英语翻译能力和初步具备能够直接从外文资料中获取信息的能力。 (一)知识目标 1、掌握专业英语中的基本词汇和专有名词; 2、掌握专业英语中常用的语法和句型结构; 3、可以阅读有一定词汇量的专业英语文献。 (二)能力目标 通过对《汽车专业英语》的教学,力求向学生提供未来工作岗位所需要专业英语知识,培养学生在实际工作岗位上运用汽车专业英语的能力。
1、阐述“专业阅读”,内容力求反应汽车专业方面的最新知识,文章能展示当今汽车专业方面的最新技术,同时书中附带一些真实的现场照片。 2、阐述“专业术语”,帮助学生了解汽车各零部件的功能及应用,是学生进入企业后应用较多的内容。 3、阐述“试试您的动手能力”,以汽车故障诊断为主,列举大量贴近企业工作实际的实例。 4、阐述“交际会话”,选用贴近实际,贴近企业,贴近岗位的常用专业英语会话。 (三)素质目标 通过教学应使学生认识《汽车专业英语》学习的基本方法, 1、具备通过查阅资料等方法,通过自学获取知识和新技术的能力; 2、通过不同形式的探究活动、自主学习,体验科技发现和创造的历程,发展抽象思维和辨证逻辑思维。 3、养成严谨求实的科学态度以及质疑和独立思考的学习习惯。 4、使学生具备正确的价值观与评定事物的能力,具备一定的英文语言表达能力以及与人交往沟通的能力。 5、培养学生爱岗敬业、团结协作、吃苦耐劳的职业精神与创新设计的意识。 三、课程内容设计 (一)学时分配
unit1 body 车身chassis 底盘enclosure外壳、套hood车棚、车顶sway 摇摆frame车架steering转向、操作brake 制动weld焊接rivet铆钉bolt螺钉washer垫圈vibration 振动stabilizer稳定器ride乘坐舒适性handling操作稳定性linkages转向传动机构plier钳子distributor分电器alternator交流发电机regulator调节器carburetor化油器radiator散热器、水箱defroster除冰装置sludge金属碎屑transmission变速器differential 差速器power train 传动系unitized body 承载式车身suspension system 悬架系统steering system 转向系braking system 制动系shock absorbers减震器control arms控制臂steering wheel 转向盘steering column转向管柱steering gears 转向器tie rod 横拉杆idler arm随动臂brake shoe制动蹄disc brake 盘式制动器drum brakes 鼓式制动器ignition system 点火系统exhaust system 排气系统lubrication system 润滑系oil filters 机油滤清器drive(or propeller)shaft传动轴universal joints 万向节dynamo发电机horn喇叭swived 旋转steering box转向器timing gear 正时齿轮bevel gear 锥齿轮mesh with与啮合leaf spring 钢板弹簧stub axle 转向节 unit2 longitudinal纵向的transverse横向的reciprocate往复spin旋转piston活塞ignite点火rub摩擦quart夸脱reservoir油箱mechanical机械的enclosed被附上的gallon加仑stroke冲程camshaft凸轮轴combustion燃烧disengaged脱离啮合的flywheel飞轮internal-combustion engine内燃机diesel-fuel柴油LPG=Liquefied Petroleum Gas液化石油气体CNG=Compressed natural gas压缩天然气spark ignition火花点火compression ignition压缩点火spark plug火花塞gas-turbine engine蒸汽机Stirling engine斯特灵发动机lubricating system润滑系统oil pan油底壳oil pump机油泵exhaust system排气系统emission-control system排放控制系统energy conversion能量转换air/fuel ratio空燃比connecting rod连杆TDC=Top Dead Center上止点BDC=Bottom Dead Center 下止点intake stroke进气冲程compression stroke压缩冲程power stroke作功冲程exhaust stroke排气冲程compression ratio压缩比lifter挺柱rocker摇臂retainer弹簧座seal密封件tappet 推杆lobe凸起gasket垫圈valve train配气机构cam follower气门挺柱rocker arm摇臂combustion chamber燃烧室intake valve进气阀exhaust valve排气阀valve stem气门杆valve cover气门室盖valve port阀口valve guide气门导管 unit3
汽车专业英语 主编:李崑 课后专业词汇汇总(带音标) 汇总:徐艳民 1 automobile ['?:t?m?ubi:l, ,?:t?m?'bi:l]汽车(美) assembly line [?'sembli]装配线 petroleum refining [pi'tr?uli?m, p?-]石油提炼 body and frame车身与车架 engine ['end?in] 发动机、引擎 drive line 传动系统 running gear 控制装置 suspension[s?'spen??n]悬架系统 unitized body ['ju:nitaizd]整体式车身 gasoline engine ['ɡ?s?li:n]汽油机 diesel engine ['di:z?l]柴油机 gas turbine['t?:bain, -bin]燃气轮机 battery ['b?t?ri]电池、电池组 fuel cell燃料电池 hybrid power ['haibrid][pau?]混合动力系统 piston ['pist?n]活塞 rotary engine ['r?ut?ri]转子发动机 vehicle ['vi:ikl, 有时发'vi:hi-]交通工具、车辆 transmission [tr?nz'mi??n, tr?ns-, trɑ:n-]变速器 drive shaft传动轴 differential [,dif?'ren??l]差速器 rear axle ['?ks?l]后轴、后桥 rear-wheel drive后轮驱动 front-wheel drive 前轮驱动 braking system 制动系统 wheel车轮 tire 轮胎 steering system 转向系统 spring [sp ri?]弹簧 shock absorber [??k] [?b's?:b?]减震器 Macpherson strut [m?k'f?:sn] [str?t]麦弗逊式悬架 torsion bar ['t?:??n]扭力杆 strut rod 支撑杆 stabilizer bar ['steibilaiz?]横向稳定杆 2 internal combustion engine [in't?:n?l] [k?m'b?st??n] ['end?in]内燃机 fuel 燃料 external combustion engine [ik'st?:n?l]外燃机 steam engine 蒸汽机 intermittent combustion engine[,int?'mit?nt]间隔燃烧式发动机 continuous combustion engine [k?n'tinju?s]连续燃烧式发动机 turbine engine ['t?:bain, -bin]涡轮发动机 rocket engine ['r?kit]火箭发动机 jet (or reaction) engine喷气式发动机 Wankel engine汪克尔发动机、转子发动机 stroke [str?uk]冲程、行程 cooling system冷却系统 fuel system燃料系统 ignition system [iɡ'ni??n]点火系统 spark-ignition engine 火花点燃式发动机 compression-ignition engine 压燃式发动机 liquid-cooled 用液体冷却的、水冷的 air-cooled 用空气冷却的、风冷的 3 cylinder block 气缸体 cylinder ['silind?]气缸 connecting rod 连杆 crankshaft['kr??k,?ɑ:ft]曲轴 cylinder head气缸盖 combustion chamber[k?m'b?st??n] ['t?eimb?]燃烧室 valve气门、阀 camshaft['k?m?ɑ:ft]凸轮轴 flywheel ['flaiwi:l]飞轮 intake manifold 进气歧管 exhaust manifold ['m?nif?uld]排气歧管 carburetor [,kɑ:bju'ret?, 'kɑ:-]化油器 fuel injector 燃料喷射器 cast iron ['ai?n]铸铁 aluminum [?'lju:min?m]铝 cooling fluid 冷却液 spark plug [pl?ɡ]火花塞 intake valve进气门 exhaust valve[iɡ'z?:st]排气门 cam凸轮 gear齿轮 belt皮带 chain链条 overhead camshaft (OHC) 凸轮轴上置式 rpm=revolutions per minute[,rev?'lju:??n]转速、转数/分钟 horsepower ['h?:s,pau?]马力、功率 intake system 进气系统 sensor ['sens?, -s?:]传感器 oxygen sensor ['?ksid??n]氧传感器 fuel induction system[in'd?k??n]燃料吸入系统 4 fuel tank 燃料箱、油箱 fuel line燃料管路 fuel pump 燃料泵、燃油泵 fuel filter [filt?]燃料滤清器 PCM (power train control module) 动力系统控制模块(计算机)
INTERNAL COMBUSTION ENGINE 引擎燃烧室 1. principle of operation 原理 Engine and power : Engine is used to produce power. The chemical energy in fuel is converted to heat by the burning of the fuel at a controlled rate. This process is called combustion. If engine combustion occurs with the power chamber. ,the engine is called internal combustion engine. If combustion takes place outside the cylinder, the engine is called an external combustion engine. Engine used in automobiles are internal combustion heat engines. Heat energy released in the combustion chamber raises the temperature of the combustion gases with the chamber. The increase in gas temperature causes the pressure of the gases to increase. The pressure developed within the combustion chamber is applied to the head of a piston to produce a usable mechanical force, which is then converted into useful mechanical power. 译: 引擎和能量: 引擎为汽车提供能量,燃料的化学能通过燃烧,转化为热能,这个过程叫燃烧。假如燃烧在燃烧室,这样的发动机叫内燃机。假如燃烧在气缸外,这样的发动机叫外燃机。 用在汽车上的一般是内燃机,热能在燃烧室释放,燃烧室气体温度升高。气体温度的升高使气体的压力曾加,燃烧室内的高压气体作用在活塞头部产生可以利用的化学能,化学能转化为机械能。 Engine T erms : Linking the piston by a connecting rod to a crankshaft causes the gas to rotate the shaft through half a turn. The power stroke “uses up” the gas , so means must be provided to expel the burnt gas and recharge the cylinder with a fresh petrol-air mixture :this control of gas movement is the duty of the valves ;an inlet valve allows the new mixture to enter at the right time and an exhaust valve lets out the burnt gas after the gas has done its job. Engine terms are : TDC(Top Dead Center):the position of the crank and piston when the piston is farther away from the crankshaft. BDC(Bottom Dead Center):the position of the crank and piston when the piston is nearest to the crankshaft. Stroke : the distance between BDC and TDC; stroke is controlled by the crankshaft. Bore : the internal diameter of the cylinder. Swept volume : the volume between TDC and BDC Engine capacity : this is the swept volume of all the cylinder e.g. a four-stroke having a capacity of two liters(2000cm) has a cylinder swept volume of 50cm. Clearance volume: the volume of the space above the piston when it is at TDC. Compression ratio = (swept vol + clearance vol)\(clearance vol) Two-stroke : a power stroke every revolution of the crank.
1、车辆vehicle 2、底盘chassis 3、货车truck 4、微型货车mini truck 5、轻型货车light truck 6、中型货车 medium truck 6、重型货车 heavy duty truck 7、越野汽车 off-road truck 8、自卸汽车 dump truck 9、专用汽车 special purpose vehicle 10、客车 passenger car 11、车长 vehicle length 12、车宽 vehicle width 13、车高 vehicle height 14、轴距 wheel base 15、轮距 tread
16、前悬 front overhang 17、后悬 rear overhang 18、柴油机 diesel 19、汽油机gasoline fueled engine 20、活塞 piston 21、喷油嘴 nozzle 22、火花塞 spark 23、曲轴 crank shaft 24、分电器 distributor 25、发电机 alternator 26、飞轮壳 flywheel housing 27、起动机 starter 28、散热器 radiator 29、凸轮轴 camshaft 30、进气门 Intake valve 31、排气门 exhaust valve
32、气缸盖cylinder head 33、水泵water pump 34、风扇皮带轮fan pulley 35、活塞环piston ring 36、机油泵 oil pump 37、离合器 clutch 38、离合器操纵机构 clutch operation 39、飞轮 flywheel 40、从动盘磨擦衬片 clutch plate lining driven plate lining (GB) 41、离合器盖 clutch cover (GB) 42、压盘 pressure plate 43、分离杆 release lever 44、分离套筒 release sleeve 45、从动盘 clutch plate 46、分离弹簧 release spring 47、分离轴承 release thrust bearing
汽车专业英语复习题 名词翻译: 1、活塞环 piston ring 2、电控系统electronic control system 3、里程表speedometer 4、发动机排量engine capacity 5、自动变速器automatic transmission 6、机油表oil gauge 7、方向盘steering wheel 8、做功冲程power stroke 9、exhaust gas废气 10. electric current电流 11. high gear高速档 12. automobile dealing汽车贸易 13. sports car 跑车 14. instrument panel仪表板 15. accelerator pedal加速踏板 16. physical property 物理性能 17、电子燃油计量系统electronic fuel metering system 18、减速slow down 19、刹车蹄brake shoe 20、General Motor 通用 21、wheel drum 车轮毂 22、TDC 上止点 23、BDC 下止点 翻译(中译英): 上海汽车工业总公司已与德国大众和美国通用两大汽车公司建立了合资公司。 The Shanghai Auto Industry Corportion has established joint ventures with German V olkswagen and American General Motors. 四冲程发动机—曲柄旋转两圈做功一次。 Four stroke —a power stroke every other revolution of the crank. 液体冷却系由水泵、水套、发动机风扇、散热器等组成。 The liquid cooling system consists of water pumps,water jackets,engine fan ,radiator and so on. 在仪表板上,我们能看见几个显示发动机运转情况的仪表。
1、车辆 vehicle 2、底盘 chassis 3、货车 truck 4、微型货车 mini truck 5、轻型货车 light truck 6、中型货车 medium truck 6、重型货车 heavy duty truck 7、越野汽车 off-road truck 8、自卸汽车 dump truck 9、专用汽车 special purpose vehicle 10、客车 passenger car 11、车长 vehicle length 12、车宽 vehicle width 13、车高 vehicle height 14、轴距 wheel base 15、轮距 tread 16、前悬 front overhang 17、后悬 rear overhang 18、柴油机 diesel 19、汽油机 gasoline fueled engine 20、活塞 piston 21、喷油嘴 nozzle 22、火花塞
spark 23、曲轴 crank shaft 24、分电器 distributor 25、发电机alternator 26、飞轮壳 flywheel housing 27、起动机 starter 28、散热器 radiator 29、凸轮轴camshaft 30、进气门Intake valve 31、排气门 exhaust valve 32、气缸盖 cylinder head 33、水泵 water pump 34、风扇皮带轮 fan pulley 35、活塞环 piston ring 36、机油泵 oil pump 37、离合器 clutch 38、离合器操纵机构 clutch operation 39、飞轮 flywheel 40、从动盘磨擦衬片 clutch plate lining driven plate lining (GB) 41、离合器盖 clutch cover (GB) 42、压盘 pressure plate 43、分离杆 release lever 44、分离套筒 release sleeve 45、从动盘
(6)Maintain correct viscosity (free flowing at all temperatures). 保持正确的粘度(在所有温度下自由流动)。 When the brake fluid boils, it becomes vapor. A vapor can be compressed, but a liquid cannot be compressed. Pressing on the brake pedal will compress the vapor in the lines instead of transferring the pressure through the fluid. This can lead to partial or complete braking system failure, sometimes called brake pedal fade. Mountain driving puts increased duty on brakes and brake fluid. The boiling point drops at high altitude. This naturally increases the tendency towards vapor lock. In fact, vapor lock in the hydraulic braking system is the primary reason for brake pedal fade. 当制动液沸腾时,它变成蒸汽。可以压缩蒸汽,但不能压缩液体。按压制动踏板将压缩管线中的蒸汽,而不是将压力传递通过流体。这可能导致部分或完全制动系统故障,有时称为制动踏板褪色。山地驾驶增加了刹车和制动液的使用。沸点在高海拔下降。这自然增加了气体锁定的趋势。事实上,液压制动系统中的汽油锁是制动踏板褪色的主要原因。 Vehicle manufacturers recommend brake fluid that meets or exceeds SAE (Societyof Automotive Engineers)andDOT (Department of Transportation) specifications. 车辆制造商推荐符合或超过SAE(汽车工程师协会)和DOT(运输部)规格的制动液。 Standard brake fluid (DOT 3) is composed chiefly of equal parts of alcohol and castor oil. This combination of fluids works well under normal conditions but it easily boils and becomes a vapor under heavy-duty applications. It also tends to separate when exposed to low temperatures. 标准制动液(DOT 3)主要由酒精和蓖麻油组成。这种流体组合在正常条件下工作良好,但在重载应用下容易沸腾并成为蒸气。暴露于低温时也容易分离。The increasing requirements of brake fluid led to the development of silicone brake fluid,such as DOT 5. This fluid achieved low water pickup and good corrosion protection and also provides good lubrication qualities and rubber compatibility. 制动液的要求越来越高,导致了DOT 5等硅胶制动液的开发。该液体实现了低吸水率和良好的防腐蚀性能,并且还具有良好的润滑性能和橡胶相容性。 5.Brake valves 5.闸阀 There are typically five types of valves in vehicle braking system to adjust the braking force distribution. 车辆制动系统中通常有五种类型的阀门来调节制动力分布。 (1)Metering valve (1)计量阀 Most vehicles that have front disc and rear drum brakes are equipped with metering valve. This metering valve controls, or delays the flow of brake fluid to the front brakes. The rear drum brakes take longer to respond than the front disc brakes. The valve ensures that front disc brake do not act before the rear drum brake. The delays is long enough to allow the rear drum brakes time to react. This delay is particularly necessary during light braking and on slick road surfaces.