外文文献：
Original Article
Impact of crack width on bond: confined and unconfined rebar David W. Law1 , Denglei Tang2, Thomas K. C. Molyneaux3 and
Rebecca Gravina3
(1 ) School of the Built Environment, Heriot Watt University, Edinburgh, EH14 4AS, UK
(2 ) VicRoads, Melbourne, VIC, Australia
(3 ) School of Civil, Environmental and Chemical Engineering, RMIT University, Melbourne, VIC, 3000, Australia
David W. Law
Email:
Received: 14 January 2010 Accepted: 14 December 2010 Published online: 23 December 2010
Abstract
This paper reports the results of a research project comparing the effect of surface crack width and degree of corrosion on the bond strength of confined and unconfined deformed 12 and 16 mm mild steel reinforcing bars. The corrosion was induced by chloride contamination of the concrete and an applied DC current. The principal parameters investigated were confinement of the reinforcement, the cover depth, bar diameter, degree of corrosion and the surface crack width. The results indicated that potential relationship between the crack width and the bond strength. The results also showed an increase in bond strength at the point where initial surface cracking was observed for bars with confining stirrups. No such increase was observed with unconfined specimens. Keywords: bond ;corrosion ; rebar ; cover ; crack width ; concrete
1 Introduction
The corrosion of steel reinforcement is a major cause of the deterioration of reinforced concrete structures throughout the world. In uncorroded structures the bond between the steel reinforcement and the concrete ensures that reinforced concrete acts in a composite manner. However, when corrosion of the steel occurs this composite performance is adversely affected. This is due to the formation of corrosion products on the steel surface, which affect the bond between the steel and the concrete.
The deterioration of reinforced concrete is characterized by a general or localized loss of section on the reinforcing bars and the formation of expansive corrosion products. This deterioration can affect structures in a number of ways; the production of expansive products creates tensile stresses within the concrete, which can result in cracking and spalling of the concrete cover. This cracking can lead to accelerated ingress of the aggressive agents causing further corrosion. It can also result in a loss of strength and stiffness of the concrete cover. The corrosion products can also affect the bond strength between the concrete and the reinforcing steel. Finally the corrosion reduces the cross section of the reinforcing steel, which can affect the ductility of the steel and the
load bearing capacity, which can ultimately impact upon the serviceability of the structure and the structural capacity [, ].
Previous research has investigated the impact of corrosion on bond [–, , , , –, , ], with a number of models being proposed [, , , , , , , ]. The majority of this research has focused on the relationship between the level of corrosion (mass loss of steel) or the current density degree (corrosion current applied in accelerated testing) and crack width, or on the relationship between bond strength and level of corrosion. Other research has investigated the mechanical behaviour of corroded steel [, ] and the friction characteristics []. However, little research has focused on the relationship between crack width and bond [, , ], a parameter that can be measured with relative ease on actual structures.
The corrosion of the reinforcing steel results in the formation of iron oxides which occupy a larger volume than that of the parent metal. This expansion creates tensile stresses within the surrounding concrete, eventually leading to cracking of the cover concrete. Once cracking occurs there is a loss of confining force from the concrete. This suggests that the loss of bond capacity could be related to the longitudinal crack width []. However, the use of confinement within the concrete can counteract this loss of bond capacity to a certain degree. Research to date has primarily involved specimens with confinement. This paper reports a
study comparing the loss of bond of specimens with and without confinement.
2 Experimental investigation
Specimens
Beam end specimens [] were selected for this study. This type of eccentric pullout or ‘beam end’ type specimen uses a bonded length representative of the anchorage zone of a typical simply supported beam. Specimens of rectangular cross section were cast with a longitudinal reinforcing bar in each corner, Fig. . An 80 mm plastic tube was provided at the bar underneath the transverse reaction to ensure that the bond strength was not enhanced due to a (transverse) compressive force acting on the bar over this length.
Fig. 1 Beam end specimen
Deformed rebar of 12 and 16 mm diameter with cover of three times bar diameter were investigated. Duplicate sets of confined and unconfined specimens were tested. The confined specimens had three sets of 6 mm stainless steel stirrups equally spaced from the plastic tube, at 75 mm centres.
This represents four groups of specimens with a combination of different bar diameter and with/without confinement. The specimens were selected in order to investigate the influence of bar size, confinement and crack width on bond strength.
Materials
The mix design is shown, Table . The cement was Type I Portland cement, the aggregate was basalt with specific gravity . The coarse and fine aggregate were prepared in accordance with AS 1141-2000. Mixing was undertaken in accordance with AS . Specimens were cured for
28 days under wet hessian before testing.
Table 1 Concrete mix design
Mater ial Cemen
t
w/
c
Sand
10 mm
washe
d
aggreg
ate
7 mm
washe
d
aggreg
ate
Salt Slump
Quant ity 381 kg/
m3
517 kg/
m3
463 kg/
m3
463 kg/
m3
kg/m3
140 ± 25 m
m
In order to compare bond strength for the different concrete compressive strengths, Eq. is used to normalize bond strength for non-corroded specimens as has been used by other researcher [].
(1)
where is the bond strength for grade 40 concrete, τ exptl is the experimental bond strength and f c is the experimental compressive strength.
The tensile strength of the Φ12 and Φ16 mm steel bars was nominally 500 MPa, which equates to a failure load of and kN, respectively.
Experiment methodology
Accelerated corrosion has been used by a number of authors to replicate the corrosion of the reinforcing steel happening in the natural environment [, , , , , , , , , , ]. These have involved experiments using impressed currents or artificial weathering with wet/dry cycles and elevated temperatures to reduce the time until corrosion, while maintaining deterioration mechanisms representative of natural exposure. Studies using impressed currents have used current densities between 100 μA/cm2 and 500 mA/cm2 []. Research has suggested that current densities up to 200 μA/cm2 result in similar stresses during the early stages of corrosion when compared to 100 μA/cm2 []. As such an applied current density of 200 μA/cm2 was selected for this study—representative of the lower end of the spectrum of such current densities adopted in previous research. However, caution should be applied when accelerating the corrosion using impressed current as the acceleration process does not exactly replicate the mechanisms involved in actual structures. In accelerated tests the pits are not allowed to progress naturally, and there may be a more uniform corrosion on the surface. Also the rate of corrosion may impact on the corrosion products,
such that different oxidation state products may be formed, which could impact on bond.
The steel bars served as the anode and four mild steel metal plates were fixed on the surface to serve as cathodes. Sponges (sprayed with salt water) were placed between the metal plates and concrete to provide an adequate contact, Fig. .
Fig. 2 Accelerated corrosion system
When the required crack width was achieved for a particular bar, the impressed current was discontinued for that bar. The specimen was removed for pullout testing when all four locations exhibited the target crack width. Average surface crack widths of , , 1 and mm were adopted as the target crack widths. The surface crack width was measured at
20 mm intervals along the length of the bar, beginning 20 mm from the end of the (plastic tube) bond breaker using an optical microscope. The level of accuracy in the measurements was ± mm. Measurements of crack width were taken on the surface normal to the bar direction regardless of the actual crack orientation at that location.
Bond strength tests were conducted by means of a hand operated hydraulic jack and a custom-built test rig as shown in Fig. . The loading scheme is illustrated in Fig. . A plastic tube of length 80 mm was provided at the end of the concrete section underneath the transverse reaction to ensure that the bond strength was not enhanced by the reactive (compressive) force (acting normal to the bar). The specimen was positioned so that an axial force was applied to the bar being tested. The restraints were sufficiently rigid to ensure minimal rotation or twisting of the specimen during loading.
Fig. 3 Pull-out test, 16 mm bar unconfined
Fig. 4 Schematic of loading. Note: only test bar shown for clarity
3 Experimental results and discussion
Visual inspection
Following the accelerated corrosion phase each specimen was visually inspected for the location of cracks, mean crack width and maximum crack width (Sect. .
While each specimen had a mean target crack width for each bar, variations in this crack width were observed prior to pull out testing. This is due to corrosion and cracking being a dynamic process with cracks propagating at different rates. Thus, while individual bars were disconnected, once the target crack width had been achieved, corrosion and crack propagation continued (to some extent) until all bars had achieved the target crack width and pull out tests conducted. This resulted in a range of data for the maximum and mean crack widths for the pull out tests.
The visual inspection of the specimens showed three stages to the cracking process. The initial cracks occurred in a very short period, usually generated within a few days. After that, most cracks grew at a
constant rate until they reached 1 mm, 3–4 weeks after first cracking. After cracks had reached 1 mm they then grew very slowly, with some cracks not increasing at all. For the confined and unconfined specimens the surface cracks tended to occur on the side of the specimens (as opposed to the top or bottom) and to follow the line of the bars. In the case of the unconfined specimens in general these were the only crack while it was common in the cases of confined specimens to observe cracks that were aligned vertically down the side—adjacent to one of the links, Fig. .
Fig. 5 Typical crack patterns
During the pull-out testing the most common failure mode for both confined and unconfined was splitting failure—with the initial (pre-test) cracks caused by the corrosion enlarging under load and ultimately leading to the section failing exhibiting spalling of the top corner/edge, Fig. . However for several of the confined specimens, a second mode of failure also occurred with diagonal (shear like) cracks appearing in the side walls, Fig. . The appearance of these cracks did not appear to be
related to the presence of vertical cracks observed (in specimens with stirrups) during the corrosion phase as reported above.
Fig. 6 Longitudinal cracking after pull-out
Fig. 7 Diagonal cracking after pull-out
The bars were initially (precasting) cleaned with a 12% hydrochloric acid solution, then washed in distilled water and neutralized by a calcium hydroxide solution before being washed in distilled water again. Following the pull-out tests, the corroded bars were cleaned in the same way and weighed again.
The corrosion degree was determined using the following equation
where G 0 is the initial weight of the steel bar before corrosion, G is the final weight of the steel bar after removal of the post-test corrosion products, g 0 is the weight per unit length of the steel bar and g/mm for Φ12 and Φ16 mm bars, respectively), l is the embedded bond length.
Figures and show steel bars with varying degree of corrosion. The majority exhibited visible pitting, similar to that observed on reinforcement in actual structures, Fig. . However, a small number of others exhibited significant overall section loss, with a more uniform level of corrosion, Fig. , which may be a function of the acceleration methodology.
Fig. 8 Corroded 12 mm bar with approximately 30% mass loss
Fig. 9 Corroded 16 mm bar with approximately 15% mass loss
Bond stress and crack width
Figure shows the variation of bond stress with mean crack width for 16 mm bars and Fig. for the 12 mm bars. Figures and show the data for the maximum crack width.
Fig. 10 Mean crack width versus bond stress for 16 mm bars
Fig. 11 Mean crack width versus bond stress for 12 mm bars
Fig. 12 Maximum crack width versus bond stress for 16 mm bars
Fig. 13 Maximum crack width versus bond stress for 12 mm bars
The data show an initial increase in bond strength for the 12 mm specimens with stirrups, followed by a significant decrease in bond, which is in agreement with other authors [, ]. For the 16 mm specimens an increase on the control bond stress was observed for specimens with and mm mean crack widths, however, a decrease in bond stress was observed for at the mean crack width of mm.
The 12 mm bars with stirrups displayed an increase in bond stress of approximately 25% from the control values to the maximum bond stress. An increase of approximately 14% was observed for the 16 mm
specimens. Other researchers [, , ] have reported enhancements of bond stress of between 10 and 60% due to confinement, slightly higher to that observed in these experiment. However the loading techniques and cover depths have not all been the same. Variations in experimental techniques include a shorter embedded length and a lower cover. The variation on the proposed empirical relationship between bond strength, degree of corrosion, bar size, cover, link details and tensile strength predicted by Rodriguez [] has been discussed in detail in Tang et al. []. The analysis demonstrates that there would be an expected enhancement of bond strength due to confinement of approximately 25%—corresponding to a change of bond strength of approximately MPa for the 16 mm bars (assessed at a 2% section loss). For the 12 mm bars the corresponding effect of confinement is found to be approximately 35% corresponding to a MPa difference in bond stress. The experimental results (14 and 25%, above) are 60–70% of these values.
Both sets of data indicate a relationship showing decreasing bond strength with (visible surface) crack width. A regression analysis of the bond strength data reveals a better linear relationship with the maximum crack width as opposed to the mean crack width (excluding the uncracked confined specimens), Table .
Table 2 Best fit parameters, crack width versus bond strength
There was also a significantly better fit for the unconfined specimens than the confined specimens. This is consistent with the observation that in the unconfined specimens the bond strength will be related to the bond between the bars and the concrete, which will be affected by the level of corrosion present, which itself will influence the crack width. In confined specimens the confining steel will impact upon both the bond and the cracking.
Corrosion degree and bond stress
It is apparent that (Fig. ) for corrosion degrees less than 5% the bond stress correlated well. However, as the degree of corrosion increased there was no observable correlation at all. This contrasts with the relationship between the observed crack width and bond stress, which gives a reasonable correlation, even as crack widths increase to 2
and mm. A possible explanation for this variation is that in the initial stages of corrosion virtually all the dissolved iron ions react to form expansive corrosion products. This reaction impacts on both the bond stress and the formation of cracks. However, once cracks have been formed it is possible for the iron ions to be transported along the crack and out of the concrete. As the bond has already been effectively lost at the crack any iron ions dissolving at the crack and being directly transported out of the concrete will cause an increase in the degree of corrosion, but not affect the surface crack width. The location, orientation and chemistry within the crack will control the relationship between bond stress and degree of corrosion, which will vary from specimen to specimen. Hence the large variations in corrosion degree and bond stress for high levels of corrosion.
Fig. 14 Bond stress versus corrosion degree, 12 mm bars, unconfined
specimen
Significantly larger crack widths were observed for the unconfined specimens, compared to the confined specimens with similar levels of corrosion and mass lost. The largest observed crack for unconfined specimens was mm compared to mm for the confined specimens. This is as expected and is a direct result of the confinement which limits the degree of cracking.
Effect of confinement
The unconfined specimens for both 16 and 12 mm bars did not display the initial increase in bond strength observed for the confined bars. Indeed the unconfined specimens with cracks all displayed a reduced bond stress compared to the control specimens. This is in agreement with other authors [, ] findings for cracked specimens. In cracked corroded specimens Fang observed a substantial reduction in bond strength for deformed bars without stirrups, while Rodriguez
本科毕业设计 外文文献及译文 文献、资料题目：Designing Against Fire Of Building 文献、资料来源：国道数据库 文献、资料发表（出版）日期：2008.3.25 院（部）：土木工程学院 专业：土木工程 班级：土木辅修091 姓名：武建伟 学号：2008121008 指导教师：周学军、李相云 翻译日期： 20012.6.1
外文文献: Designing Against Fire Of Buliding John Lynch ABSTRACT: This paper considers the design of buildings for fire safety. It is found that fire and the associ- ated effects on buildings is significantly different to other forms of loading such as gravity live loads, wind and earthquakes and their respective effects on the building structure. Fire events are derived from the human activities within buildings or from the malfunction of mechanical and electrical equipment provided within buildings to achieve a serviceable environment. It is therefore possible to directly influence the rate of fire starts within buildings by changing human behaviour, improved maintenance and improved design of mechanical and electrical systems. Furthermore, should a fire develops, it is possible to directly influence the resulting fire severity by the incorporation of fire safety systems such as sprinklers and to provide measures within the building to enable safer egress from the building. The ability to influence the rate of fire starts and the resulting fire severity is unique to the consideration of fire within buildings since other loads such as wind and earthquakes are directly a function of nature. The possible approaches for designing a building for fire safety are presented using an example of a multi-storey building constructed over a railway line. The design of both the transfer structure supporting the building over the railway and the levels above the transfer structure are considered in the context of current regulatory requirements. The principles and assumptions associ- ated with various approaches are discussed. 1 INTRODUCTION Other papers presented in this series consider the design of buildings for gravity loads, wind and earthquakes.The design of buildings against such load effects is to a large extent covered by engineering based standards referenced by the building regulations. This is not the case, to nearly the same extent, in the
土木工程毕业设计外文文献翻译修订版 IBMT standardization office【IBMT5AB-IBMT08-IBMT2C-ZZT18】
外文文献翻译 Reinforced Concrete （来自《土木工程英语》） Concrete and reinforced concrete are used as building materials in every country. In many, including the United States and Canada, reinforced concrete is a dominant structural material in engineered construction. The universal nature of reinforced concrete construction stems from the wide availability of reinforcing bars and the constituents of concrete, gravel, sand, and cement, the relatively simple skills required in concrete construction, and the economy of reinforced concrete compared to other forms of construction. Concrete and reinforced concrete are used in bridges, buildings of all sorts underground structures, water tanks, television towers, offshore oil exploration and production structures, dams, and even in ships. Reinforced concrete structures may be cast-in-place concrete, constructed in their final location, or they may be precast concrete produced in a factory and erected at the construction site. Concrete structures may be severe and functional in design, or the shape and layout and be whimsical and artistic. Few other building materials off the architect and engineer such versatility and scope. Concrete is strong in compression but weak in tension. As a result, cracks develop whenever loads, or restrained shrinkage of temperature changes, give rise to tensile stresses in excess of the tensile strength of the concrete. In
专业资料 学院： 专业：土木工程 姓名： 学号： 外文出处：Structural Systems to resist (用外文写) Lateral loads 附件：1.外文资料翻译译文；2.外文原文。
附件1：外文资料翻译译文 抗侧向荷载的结构体系 常用的结构体系 若已测出荷载量达数千万磅重，那么在高层建筑设计中就没有多少可以进行极其复杂的构思余地了。确实，较好的高层建筑普遍具有构思简单、表现明晰的特点。 这并不是说没有进行宏观构思的余地。实际上，正是因为有了这种宏观的构思，新奇的高层建筑体系才得以发展，可能更重要的是：几年以前才出现的一些新概念在今天的技术中已经变得平常了。 如果忽略一些与建筑材料密切相关的概念不谈，高层建筑里最为常用的结构体系便可分为如下几类： 1.抗弯矩框架。 2.支撑框架，包括偏心支撑框架。 3.剪力墙，包括钢板剪力墙。 4.筒中框架。 5.筒中筒结构。 6.核心交互结构。 7. 框格体系或束筒体系。 特别是由于最近趋向于更复杂的建筑形式，同时也需要增加刚度以抵抗几力和地震力，大多数高层建筑都具有由框架、支撑构架、剪力墙和相关体系相结合而构成的体系。而且，就较高的建筑物而言，大多数都是由交互式构件组成三维陈列。 将这些构件结合起来的方法正是高层建筑设计方法的本质。其结合方式需要在考虑环境、功能和费用后再发展，以便提供促使建筑发展达到新高度的有效结构。这并
不是说富于想象力的结构设计就能够创造出伟大建筑。正相反，有许多例优美的建筑仅得到结构工程师适当的支持就被创造出来了，然而，如果没有天赋甚厚的建筑师的创造力的指导，那么，得以发展的就只能是好的结构，并非是伟大的建筑。无论如何，要想创造出高层建筑真正非凡的设计，两者都需要最好的。 虽然在文献中通常可以见到有关这七种体系的全面性讨论，但是在这里还值得进一步讨论。设计方法的本质贯穿于整个讨论。设计方法的本质贯穿于整个讨论中。 抗弯矩框架 抗弯矩框架也许是低，中高度的建筑中常用的体系，它具有线性水平构件和垂直构件在接头处基本刚接之特点。这种框架用作独立的体系，或者和其他体系结合起来使用，以便提供所需要水平荷载抵抗力。对于较高的高层建筑，可能会发现该本系不宜作为独立体系，这是因为在侧向力的作用下难以调动足够的刚度。 我们可以利用STRESS，STRUDL 或者其他大量合适的计算机程序进行结构分析。所谓的门架法分析或悬臂法分析在当今的技术中无一席之地，由于柱梁节点固有柔性，并且由于初步设计应该力求突出体系的弱点，所以在初析中使用框架的中心距尺寸设计是司空惯的。当然，在设计的后期阶段，实际地评价结点的变形很有必要。 支撑框架 支撑框架实际上刚度比抗弯矩框架强，在高层建筑中也得到更广泛的应用。这种体系以其结点处铰接或则接的线性水平构件、垂直构件和斜撑构件而具特色，它通常与其他体系共同用于较高的建筑，并且作为一种独立的体系用在低、中高度的建筑中。
（ 二 〇 一 二 年 六 月 外文文献及翻译 题 目： About Buiding on the Structure Design 学生姓名： 学 院：土木工程学院 系 别：建筑工程系 专 业：土木工程(建筑工程方向) 班 级：土木08-4班 指导教师：
英文原文： Building construction concrete crack of prevention and processing Abstract The crack problem of concrete is a widespread existence but again difficult in solve of engineering actual problem, this text carried on a study analysis to a little bit familiar crack problem in the concrete engineering, and aim at concrete the circumstance put forward some prevention, processing measure. Keyword:Concrete crack prevention processing Foreword Concrete's ising 1 kind is anticipate by the freestone bone, cement, water and other mixture but formation of the in addition material of quality brittleness not and all material.Because the concrete construction transform with oneself, control etc. a series problem, harden model of in the concrete existence numerous tiny hole, spirit cave and tiny crack, is exactly because these beginning start blemish of existence just make the concrete present one some not and all the characteristic of quality.The tiny crack is a kind of harmless crack and accept concrete heavy, defend Shen and a little bit other use function not a creation to endanger.But after the concrete be subjected to lotus carry, difference in temperature etc. function, tiny crack would continuously of expand with connect, end formation we can see without the
PA VEMENT PROBLEMS CAUSED BY COLLAPSIBLE SUBGRADES By Sandra L. Houston,1 Associate Member, ASCE (Reviewed by the Highway Division) ABSTRACT: Problem subgrade materials consisting of collapsible soils are com- mon in arid environments, which have climatic conditions and depositional and weathering processes favorable to their formation. Included herein is a discussion of predictive techniques that use commonly available laboratory equipment and testing methods for obtaining reliable estimates of the volume change for these problem soils. A method for predicting relevant stresses and corresponding collapse strains for typical pavement subgrades is presented. Relatively simple methods of evaluating potential volume change, based on results of familiar laboratory tests, are used. INTRODUCTION When a soil is given free access to water, it may decrease in volume, increase in volume, or do nothing. A soil that increases in volume is called a swelling or expansive soil, and a soil that decreases in volume is called a collapsible soil. The amount of volume change that occurs depends on the soil type and structure, the initial soil density, the imposed stress state, and the degree and extent of wetting. Subgrade materials comprised of soils that change volume upon wetting have caused distress to highways since the be- ginning of the professional practice and have cost many millions of dollars in roadway repairs. The prediction of the volume changes that may occur in the field is the first step in making an economic decision for dealing with these problem subgrade materials. Each project will have different design considerations, economic con- straints, and risk factors that will have to be taken into account. However, with a reliable method for making volume change predictions, the best design relative to the subgrade soils becomes a matter of economic comparison, and a much more rational design approach may be made. For example, typical techniques for dealing with expansive clays include: (1) In situ treatments with substances such as lime, cement, or fly-ash; (2) seepage barriers and/ or drainage systems; or (3) a computing of the serviceability loss and a mod- ification of the design to "accept" the anticipated expansion. In order to make the most economical decision, the amount of volume change (especially non- uniform volume change) must be accurately estimated, and the degree of road roughness evaluated from these data. Similarly, alternative design techniques are available for any roadway problem. The emphasis here will be placed on presenting economical and simple methods for: (1) Determining whether the subgrade materials are collapsible; and (2) estimating the amount of volume change that is likely to occur in the 'Asst. Prof., Ctr. for Advanced Res. in Transp., Arizona State Univ., Tempe, AZ 85287. Note. Discussion open until April 1, 1989. To extend the closing date one month,
外文文献翻译 1 中文翻译 1.1钢筋混凝土 素混凝土是由水泥、水、细骨料、粗骨料（碎石或；卵石）、空气，通常还有其他外加剂等经过凝固硬化而成。将可塑的混凝土拌合物注入到模板内，并将其捣实，然后进行养护，以加速水泥与水的水化反应，最后获得硬化的混凝土。其最终制成品具有较高的抗压强度和较低的抗拉强度。其抗拉强度约为抗压强度的十分之一。因此，截面的受拉区必须配置抗拉钢筋和抗剪钢筋以增加钢筋混凝土构件中较弱的受拉区的强度。 由于钢筋混凝土截面在均质性上与标准的木材或钢的截面存在着差异，因此，需要对结构设计的基本原理进行修改。将钢筋混凝土这种非均质截面的两种组成部分按一定比例适当布置，可以最好的利用这两种材料。这一要求是可以达到的。因混凝土由配料搅拌成湿拌合物，经过振捣并凝固硬化，可以做成任何一种需要的形状。如果拌制混凝土的各种材料配合比恰当，则混凝土制成品的强度较高，经久耐用，配置钢筋后，可以作为任何结构体系的主要构件。 浇筑混凝土所需要的技术取决于即将浇筑的构件类型，诸如：柱、梁、墙、板、基础，大体积混凝土水坝或者继续延长已浇筑完毕并且已经凝固的混凝土等。对于梁、柱、墙等构件，当模板清理干净后应该在其上涂油，钢筋表面的锈及其他有害物质也应该被清除干净。浇筑基础前，应将坑底土夯实并用水浸湿6英寸，以免土壤从新浇的混凝土中吸收水分。一般情况下，除使用混凝土泵浇筑外，混凝土都应在水平方向分层浇筑，并使用插入式或表面式高频电动振捣器捣实。必须记住，过分的振捣将导致骨料离析和混凝土泌浆等现象，因而是有害的。 水泥的水化作用发生在有水分存在，而且气温在50°F以上的条件下。为了保证水泥的水化作用得以进行，必须具备上述条件。如果干燥过快则会出现表面裂缝，这将有损与混凝土的强度，同时也会影响到水泥水化作用的充分进行。 设计钢筋混凝土构件时显然需要处理大量的参数，诸如宽度、高度等几何尺寸，配筋的面积，钢筋的应变和混凝土的应变，钢筋的应力等等。因此，在选择混凝土截面时需要进行试算并作调整，根据施工现场条件、混凝土原材料的供应情况、业主提出的特殊要求、对建筑和净空高度的要求、所用的设计规范以及建筑物周围环
Original Article Impact of crack width on bond: confined and unconfine d rebar David https://www.doczj.com/doc/754031111.html,w1, Denglei Tang2, Thoma s K. C.Molyneaux3 and Rebecca Gravina3 (1)School of the Built Environment, Heriot Watt University, Edinburgh, EH14 4AS, UK (2)VicRoads, Melbourne, VIC, Australia (3)School of Civil, Environmental and Chemical Engineering, RMIT University, Melbourne, VIC, 3000, Australia David W. Law Email: https://www.doczj.com/doc/754031111.html,w@https://www.doczj.com/doc/754031111.html, Received: 14January2010Accepted: 14Decemb er2010Published online: 23December2010 Abstract This paper reports the results of a research project comp aring the effect of surface crack width and degree of corrosi on on the bond strength of confined and unconfined deforme d 12 and 16mm mild steel reinforcing bars. The corrosion was induced by chloride contamination of the concrete and
Civil engineering Civil engineering is a professional engineering discipline that deals with the design, construction, and maintenance of the physical and naturally built environment, including works like bridges, roads, canals, dams, and buildings.[1][2][3] Civil engineering is the oldest engineering discipline after military engineering,[4] and it was defined to distinguish non-military engineering from military engineering.[5] It is traditionally broken into several sub-disciplines including environmental engineering, geotechnical engineering, structural engineering, transportation engineering, municipal or urban engineering, water resources engineering, materials engineering, coastal engineering,[4] surveying, and construction engineering.[6] Civil engineering takes place on all levels: in the public sector from municipal through to national governments, and in the private sector from individual homeowners through to international companies. History of the civil engineering profession See also: History of structural engineering Engineering has been an aspect of life since the beginnings of human existence. The earliest practices of Civil engineering may have commenced between 4000 and 2000 BC in Ancient Egypt and Mesopotamia (Ancient Iraq) when humans started to abandon a nomadic existence, thus causing a need for the construction of shelter. During this time, transportation became increasingly important leading to the development of the wheel and sailing. Until modern times there was no clear distinction between civil engineering and architecture, and the term engineer and architect were mainly geographical variations referring to the same person, often used interchangeably.[7]The construction of Pyramids in Egypt (circa 2700-2500 BC) might be considered the first instances of large structure constructions. Other ancient historic civil engineering constructions include the Parthenon by Iktinos in Ancient Greece (447-438 BC), the
1 中文翻译 摘要：为了研究连续型拓扑优化理论在实际工程中的应用，该文给出了一种多层钢框架支撑体系连续型拓扑优化设计方法。基于灵敏度分析，探讨了连续体结构在多工况荷载作用下、同时受应力和多位移约束的拓扑优化删除准则。为保证拓扑优化结果的合理性，提出了设计区域平均厚度的概念。在该文给出的优化设计方法中，首先在不考虑位移约束的情况下对无支撑钢框架进行优化设计，然后在有位移约束的条件下采用渐进结构优化算法和删除准则对支撑体系进行连续型拓扑优化设计，并将获得的支撑最优拓扑构形转化成相应的杆件。通过一个3跨12层钢框架支撑体系的拓扑优化设计实例验证了该文给出的钢框架支撑体系连续型拓扑优化设计方法的有效性。 关键词：钢框架；支撑体系；连续型；拓扑优化；渐进结构优化 1.1钢筋混凝土 素混凝土是由水泥、水、细骨料、粗骨料（碎石或；卵石）、空气，通常还有其他外加剂等经过凝固硬化而成。将可塑的混凝土拌合物注入到模板内，并将其捣实，然后进行养护，以加速水泥与水的水化反应，最后获得硬化的混凝土。其最终制成品具有较高的抗压强度和较
低的抗拉强度。其抗拉强度约为抗压强度的十分之一。因此，截面的受拉区必须配置抗拉钢筋和抗剪钢筋以增加钢筋混凝土构件中较弱的受拉区的强度。 由于钢筋混凝土截面在均质性上与标准的木材或钢的截面存在着差异，因此，需要对结构设计的基本原理进行修改。将钢筋混凝土这种非均质截面的两种组成部分按一定比例适当布置，可以最好的利用这两种材料。这一要求是可以达到的。因混凝土由配料搅拌成湿拌合物，经过振捣并凝固硬化，可以做成任何一种需要的形状。如果拌制混凝土的各种材料配合比恰当，则混凝土制成品的强度较高，经久耐用，配置钢筋后，可以作为任何结构体系的主要构件。 浇筑混凝土所需要的技术取决于即将浇筑的构件类型，诸如：柱、梁、墙、板、基础，大体积混凝土水坝或者继续延长已浇筑完毕并且已经凝固的混凝土等。对于梁、柱、墙等构件，当模板清理干净后应该在其上涂油，钢筋表面的锈及其他有害物质也应该被清除干净。浇筑基础前，应将坑底土夯实并用水浸湿6英寸，以免土壤从新浇的混凝土中吸收水分。一般情况下，除使用混凝土泵浇筑外，混凝土都应在水平方向分层浇筑，并使用插入式或表面式高频电动振捣器捣实。必须记住，过分的振捣将导致骨料离析和混凝土泌浆等现象，因而是有害的。 水泥的水化作用发生在有水分存在，而且气温在50°F以上的条件下。为了保证水泥的水化作用得以进行，必须具备上述条件。如果干燥过快则会出现表面裂缝，这将有损与混凝土的强度，同时也会影响到水泥水化作用的充分进行。 设计钢筋混凝土构件时显然需要处理大量的参数，诸如宽度、高度等几何尺寸，配筋的面积，钢筋的应变和混凝土的应变，钢筋的应力等等。因此，在选择混凝土截面时需要进行试算并作调整，根据施工现场条件、混凝土原材料的供应情况、业主提出的特殊要求、对建筑和净空高度的要求、所用的设计规范以及建筑物周围
土木工程--外文文献翻译
学院： 专业：土木工程 姓名： 学号： 外文出处： Structural Systems to resist (用外文写) Lateral loads 附件： 1.外文资料翻译译文；2.外文原文。
附件1：外文资料翻译译文 抗侧向荷载的结构体系 常用的结构体系 若已测出荷载量达数千万磅重，那么在高层建筑设计中就没有多少可以进行极其复杂的构思余地了。确实，较好的高层建筑普遍具有构思简单、表现明晰的特点。 这并不是说没有进行宏观构思的余地。实际上，正是因为有了这种宏观的构思，新奇的高层建筑体系才得以发展，可能更重要的是：几年以前才出现的一些新概念在今天的技术中已经变得平常了。 如果忽略一些与建筑材料密切相关的概念不谈，高层建筑里最为常用的结构体系便可分为如下几类： 1.抗弯矩框架。 2.支撑框架，包括偏心支撑框架。 3.剪力墙，包括钢板剪力墙。 4.筒中框架。 5.筒中筒结构。 6.核心交互结构。 7. 框格体系或束筒体系。 特别是由于最近趋向于更复杂的建筑形式，同时也需要增加刚度以抵抗几力和地震力，大多数高层建筑都具有由框架、支撑构架、剪力墙和相关体系相结合而构成的体系。而且，就较高的建筑物而言，大多数都是由交互式构件组成三维陈列。 将这些构件结合起来的方法正是高层建筑设计方法的本质。其结合方式需要在考虑环境、功能和费用后再发展，以便提供促使建筑发展达到新高度的有效结构。这并不是说富于想象力的结构设计就能够创造出伟大建筑。正相反，有许多例优美的建筑仅得到结构工程师适当的支持就被创造出来了，然而，如果没有天赋甚厚的建筑师的创造力的指导，那么，得以发展的就只能是好的结构，并非是伟大的建筑。无论如何，要想创造出高层建筑真正非凡的设计，两者都需要最好的。 虽然在文献中通常可以见到有关这七种体系的全面性讨论，但是在这里还值得进一步讨论。设计方法的本质贯穿于整个讨论。设计方法的本质贯穿于整个讨论中。
毕业设计（论文） 外文文献翻译 文献、资料中文题目：钢筋混凝土结构设计 文献、资料英文题目：DESIGN OF REINFORCED CONCRETE STRUCTURES 文献、资料来源： 文献、资料发表（出版）日期： 院（部）： 专业：土木工程 班级： 姓名： 学号： 指导教师： 翻译日期： 2017.02.14
毕业设计（论文）外文参考 资料及译文 译文题目：DESIGN OF REINFORCED CONCRETE STRUCTURES 原文： DESIGN OF REINFORCED CONCRETE STRUCTURES 1. BASIC CONCERPTS AND CHARACERACTERISTICS OF REINFORCED CONCRETE Plain concrete is formed from hardened mixture of cement, water , fine aggregate , coarse aggregate (crushed stone or gravel ) , air and often other admixtures . The plastic mix is placed and consolidated in the formwork, then cured to accelerate of the chemical hydration of hen cement mix and results in a hardened concrete. It is generally known that concrete has high compressive strength and low resistance to tension. Its tensile strength is approximately one-tenth of its compressive strength. Consequently, tensile reinforcement in the tension zone has to be provided to supplement the tensile strength of the reinforced concrete section. For example, a plain concrete beam under a uniformly distributed load q is shown in Fig . 1.1(a), when the distributed load increases and reaches a value q=1.37KN/m , the tensile region at the mid-span will be cracked and the beam will fail suddenly . A reinforced concrete beam if the same size but has to steel reinforcing bars (2φ16) embedded at the bottom under a un distributed load q is shown in Fig.1.1(b). The reinforcing bars take up the tension there after the concrete is cracked. When the load q is increased, the width of the cracks, the deflection and the
本科毕业设计（论文）外文翻译译文 学生姓名： 院（系）： 专业班级： 指导教师： 完成日期：
钢筋混凝土填充框架结构对拆除两个相邻的柱的响应 作者：Mehrdad Sasani 美国波士顿东北大学，斯奈尔400设计中心MA02115收稿日期：2007年7月27日，修整后收稿日期2007年12月26日，录用日期2008年1月24日，网上上传日期2008年3月19日。 摘要： 本文是评价圣地亚哥旅馆对同时拆除两根相邻的外柱的响应问题，圣地亚哥旅馆是个6层钢筋混凝土填充框架结构。结构的分析模型应用了有限元法和以此为基础的分析模型来计算结构的整体和局部变形。分析结果跟实验结果非常吻合。当测量的竖向位移增加到为四分之一英寸（即6.4mm）的时候，结构就发生连续倒塌。通过实验分析方法评价和讨论随着柱的移除而产生的变形沿着结构高度上的发展和荷载动态重分配。讨论了轴向和弯曲的变形传播的不同。结构横向和纵向的三维桁架在填充墙的参与下被认为是荷载重分配的主要构件。讨论了两种潜在的脆性破坏模型（没有拉力加强的梁的脆断和有加筋肋的梁的挤出）。分析评价了结构对额外的重力和无填充墙时的响应。 Elsevier有限责任公司对此文保留所有权利。 关键词： 连续倒塌；荷载重分配；对荷载抵抗能力；动态响应；非线性分析；脆性破坏。 1. 介绍： 作为减小由于结构的局部损坏而造成大量伤亡的可能性措施的一部分，美国总务管理局【1】和国防部【2】出台了一系列制度来评价结构对连续倒塌的抵抗力。【3】定义连续倒塌为，由原始单元的局部破坏在单元间的扩展最终造成结构的整体或不成比例的大部破坏。 通过Ellingwood 和Leyendecker【4】建议的方法，ASCE/SEI 7定义了两种一般模型来减小结构设计时连续倒塌效应产生的损害，它们分为直接和间接的设计方法。一般建筑规范和标准用增加结构的整体性的间接设计方法。间接设计法也应用于美国国防部的降低连续倒塌设计和未归档设备标准中。尽管间接设计法可以降低连续破坏的风险【6，7】，对基于此法设计的结构破坏后的表现的判断是不容易实现的。 有一种基于直接设计的方法通过研究瞬间消除受载构件，比如柱子，对结构的影响来评价结构的连续倒塌。美国防部和国家事务管理局的规章是要求去除一个受荷构件，考虑其影响。这样的规范目的是评价结构的整体性和结构的一个单元出现严重的毁坏时的分荷能力。这种方法是研究结构受连续倒塌的影响的程度，但是事实上初始结构损伤的影响不止局限于某一根柱子。 在本论文中，应用通过实验证实的分析结果，评价圣地亚哥旅馆抵抗连续破坏的能力，实验中瞬间移除两个相邻的柱子，其中一个柱是拐角柱。为了爆除这两个柱子，将炸药放在预先在柱子上钻的孔里面。柱子然后再用几层保护材料包裹好，以避免爆炸时的冲击波和碎片影响结构的其他部分。 2. 建筑的特性 圣地亚哥旅馆建造于1914年，在1924年又向南扩展了一部分，此部分包括两个分离的结构。图.1是从南边看旅馆的样子。注意这张照片，旅馆的第一和第三层被用黑色的布蒙了起来。这个六层的旅馆是无延性的钢筋混凝土框架结构，其中还有由空
毕业设计(论文)外文文献翻译 (2011届） 学生姓名夏银虎 学号0405070326 院系工程与技术系 专业土木工程 指导教师于周平 填写日期2010-11-13
1中文翻译 摘要：为了研究连续型拓扑优化理论在实际工程中的应用，该文给出了一种多层钢框架支撑体系连续型拓扑优化设计方法。基于灵敏度分析，探讨了连续体结构在多工况荷载作用下、同时受应力和多位移约束的拓扑优化删除准则。为保证拓扑优化结果的合理性，提出了设计区域平均厚度的概念。在该文给出的优化设计方法中，首先在不考虑位移约束的情况下对无支撑钢框架进行优化设计，然后在有位移约束的条件下采用渐进结构优化算法和删除准则对支撑体系进行连续型拓扑优化设计，并将获得的支撑最优拓扑构形转化成相应的杆件。通过一个3跨12层钢框架支撑体系的拓扑优化设计实例验证了该文给出的钢框架支撑体系连续型拓扑优化设计方法的有效性。 关键词：钢框架；支撑体系；连续型；拓扑优化；渐进结构优化 1.1钢筋混凝土 素混凝土是由水泥、水、细骨料、粗骨料（碎石或；卵石）、空气，通常还有其他外加剂等经过凝固硬化而成。将可塑的混凝土拌合物注入到模板内，并将其捣实，然后进行养护，以加速水泥与水的水化反应，最后获得硬化的混凝土。其最终制成品具有较高的抗压强度和较低的抗拉强度。其抗拉强度约为抗压强度的十分之一。因此，截面的受拉区必须配置抗拉钢筋和抗剪钢筋以增加钢筋混凝土构件中较弱的受拉区的强度。 由于钢筋混凝土截面在均质性上与标准的木材或钢的截面存在着差异，因此，需要对结构设计的基本原理进行修改。将钢筋混凝土这种非均质截面的两种组成部分按一定比例适当布置，可以最好的利用这两种材料。这一要求是可以达到的。因混凝土由配料搅拌成湿拌合物，经过振捣并凝固硬化，可以做成任何一种需要的形状。如果拌制混凝土的各种材料配合比恰当，则混凝土制成品的强度较高，经久耐用，配置钢筋后，可以作为任何结构体系的主要构件。 浇筑混凝土所需要的技术取决于即将浇筑的构件类型，诸如：柱、梁、墙、板、基础，大体积混凝土水坝或者继续延长已浇筑完毕并且已经凝固的混凝土等。对于梁、柱、墙等构件，当模板清理干净后应该在其上涂油，钢筋表面的锈及其他有害物质也应该被清除干净。浇筑基础前，应将坑底土夯实并用水浸湿6英寸，以免土