门控五金专业术语
Terminologies for door control hardware
一、地弹簧Floor hinge （Floor spring）Adjustable creep speed 缓行速度
Adjust detection sensibility 检测灵敏度调整Adjustment style 调速方式
Two-section adjustment 两端调节
Buffer 缓冲区
Closing section 关门阶段
Opening section 开门阶段
Center pivoted arm 中心摇臂
Top pivot seat 上枢轴座
Pivot bottom seat 枢轴底座
Offset pivot arm 偏心摇臂
Closing force 紧闭力
Closing speed 闭门运行速度
Opening speed 开门运行速度
Non-hold 无驻持
Hold 驻持
Economic model 经济型
Floor hinge （Floor spring）地弹簧
Hydraulic control 液压控制
Cover plate. 盖板
Cam spindle 凸轮轴
Sealing compound 密封化合物
Environmental-Protection floor hinge 环保型地弹簧Insect prevention 防虫
Water proof 防水
Keep warm 保温
Antirust 防锈
Maximum opening angle 最大开启角度Maximum loading 最大门重
Maximum loading capacity 最大承重
Maximum opening force 最大开门力
Non-antomatic pivot hinge 地轴
Pivot hinge 地轴
Door axial 门轴
Top pivot 顶轴
Upper pivot 上轴
Adjust gasket 调整垫片
Bottom Pivot 下轴
二、玻璃门夹、驳接件、铰链类
Bottom patch fitting 下夹
Upper patch fitting 上夹
Top patch fitting 顶夹
Bending patch fitting 曲夹
T patch fitting T形夹
F patch fitting F 形夹
Locker patch fitting 锁夹
Lock case patch fitting 锁盒
Long Patch fitting 长门夹
Bottom patch fitting with lock 带锁下夹
Bottom bracket 下驳接件
Upper bracket 上驳接件
Top bracket 顶驳接件
Bending bracket 曲形驳接件
Z Bracket Z形驳接件
L bracket L形驳接件
Glass door hinge 玻璃门铰链
Opening angle 开启角度
Arc precise-cast patch fitting 弧形精铸门夹
Bending precise-cast patch fitting 曲形精铸门
Heavy precise-cast patch fitting 重型精铸门夹Precise-cast patch fitting 精铸门夹系列
三、门锁类Door lock series
Frameless door lock、Latch series 无框门锁、插销系列Frame door lock 、latch series 有框门锁、插销系列Profile door lock among 型材门中间锁
Glass door lock 玻璃门锁
Glass door latch 玻璃门插销
Close device 地锁
Latch 插销
四、电锁类Electric lock series
Control center 管理中心
Card reader 读卡器
Protocol converter 协议转化器
Power controler 电源控制器
Electromagnetic lock 磁力锁
Force 拉力
Actuation current 启动电流
Input voltage 输入电压
Working current 工作电流
Signal detection 侦测信号
Electromagnetic lock for single-leaf door 单门磁力锁Electromagnetic lock for double-leaf door 双门磁力锁
Lock body size 锁体尺寸
Concealed Electromagnetic lock for single-leaf door 暗装式单门磁力锁Water-proof electromagnetic lock for single-leaf door 单门防水磁力锁Electric lock series 电插销系列
Cutout voltage 断电
Control signal 控制信号
Electric bolt 电插销
Shear lock 剪力锁
Lock after power-off 断电上锁
Shear 剪力
Bracket 支架
Electromagnetic door suck 电磁门吸
Release after powe-off 断电释放
Switch 开关
Max. Current 最大电流
Security level 安全标准
Remote control 遥控器
Remote operating range 遥控距离
Card Capacity 卡容量
Record Capacity 记录量
Alarm function 报警功能
Working Frequency 工作频率
Automatic door drive 自动门机
Microwave sensor微波感应器
Controller 控制器
Entension template 扩展模板
Safety light 安全光线
Spare battery 备用电池
Motor 马达
Credit card 刷卡器
Semi-automatic door 半自动门机
Guide rail length 导轨长度
Sash width 门扇宽度
Recommend bearing 推荐重量
Top side installation 顶部安装
Beside installation 侧面安装
Applicable braket 适用支架
Anti-jamming 抗干扰性能
Automatic door drive system 自动门机
Data storage 资料存储
Detection area 检测区域
Detection area adjustment 检测区域调整Detection method 检测模式
Detection theory 检测原理
Delay duration 保持延时
Delay function 延时功能
Density of transimission frequency 发射频率密度
Device name 配件名称
Door bell 门铃
Door coordinator 顺位器
Doppler 信息处理
Electric bolt 电插锁
Electromagnetic lock 电磁锁
Electromagnetic lock for double-leaf door 双门磁力锁Electromagnetic lock for single-leaf door 单门磁力锁Extension template 扩展模块
Lock in power off 断电关门锁
Magnetism signal 门磁信号
Microwave sensor 微波感应器
Min. detection movement speed 最小检测运动速度Module of function 功能模块
Motor 马达
Multi-function extention module 多功能扩展模块Number of infrared beam 光束数
Output watt 输出功率
Power 电源
Power controler 电源拉制器
Programmed microcomputer 微电脑程序控制器Public code 公共密码
Rate of transmission 传输速率
Safety infrared beams 安全光线开关
Sensor range 感应距离
Signal detection 信号侦测
Swipe card 刷卡
Swipe card + code 刷卡+密码
五、推拉移门类Sliding door series
Automatic door drive 制动门机
Automatic sliding door 自动平移门
Automatic revolving door 自动旋转门
Telescopic sliding door 伸缩推拉门
Concealed sliding door 隐藏式推拉门
Automatic sliding door operator 自动推拉门自动启闭装置Self monitoring radar motion detector自我监测雷达运动检测器六、拉手类Handle
Stainless steel handle不锈钢拉手
Round pipe handle 圆型执手
Square pipe handle方型执手
Special—sharped pipe handle异型执手
Precision-cast door handle 精铸门拉手
Precision-cast zinc alloy handle精铸锌合金拉手
Precision-cast stainless steel handle精铸不锈钢拉手
Single handle单支拉手
Wooden handle木质拉手
Marble handle大理石拉手
卫浴产品术语
Terminologies for Bathroom Hardware
一、水龙头（Faucet）
水龙头种类
Cleaner Faucet 净身器龙头
Concealed Faucet 暗式龙
Double Handle Faucet 双把龙头
Fast On Faucet 快开龙头
Kitchen Faucet 厨房龙头
Lavatory Faucet 脸盆龙头
Pedaled Faucet 脚踏式龙头
Shower Faucet 淋浴龙头
Shower Nozzle 淋浴喷头
Single Handle Faucet 单把龙头
Thermostat Faucet 恒温龙头
Time-lapse Faucet 延时龙头
Versatility Faucet 多功能龙头
single hole basin mixer 单孔脸盆龙头
double hole basin mixer 双孔脸盆龙头
bathtub mixer with shower head 挂墙式浴缸龙头wall-in bathtub mixer 入墙式沐浴龙头Automatic Faucet 感应龙头
Basin Faucet 台式龙头
水龙头配件
Angle Valve 角阀
Cold-water tap 水嘴
Shower mixer 淋浴水龙头
faucet, mixer tap 明三联式浴缸水嘴
shower 淋浴喷头
shower curtain 浴盆帘
Lever handle 一字型把手
Cross handle 十字把手
Handle assembly 把手组件
Cap 把手上盖
基座
二、化妆镜（Cosmetic Mirror）
安装情况
bathroom cabinet 卫生间镜箱
round front model 圆形设计
oval shape design 椭圆形设计
countertop installation 圆台面上安装fixing with back to wall 背靠墙式安装above counter mounting 台上安装
under counter mounting 台下安装
fixing above table board 柜上安装
玻璃门合页（Glass Door Hinge）
三、卫浴配件（Bathroom accessory）挂式配件
Fix Clamp 固定夹
Support Bar 浴室支撑杆
Glass Clamp玻璃夹
Connector连接件
Mounting 固定座
Rail Connecting Block 导轨支撑件Handle 拉手
Robber Hook 衣钩
towel ring毛巾环
towel bar毛巾杆
robe hook衣勾
paper holder卫生纸架
toilet brush holder马桶刷架
double towel bar 双档毛巾架
soap dish & bath lotion rack 皂碟和洗剂架towel shelf浴巾架
其他配件
Position Block 限位器
Wheel 导轮
Guide Rail 导轨
Mounting 固定座
Guide track 导槽
Mounting Bracket 支撑脚
Mount Header Bracket 吊码
Hinge 合页
Header Corner 角码
Indicator Lock 指示锁
Grab Bar For the Disabled 残弱人扶手Strip胶条
Sink地漏
Indicator指示牌
crystal水晶
shelf架子
lamp灯
metal grid金属网
soap dispenser皂液器
glass shelf玻璃平台
tumbler holder 牙刷杯架
soap holder肥皂架
wall mount shower caddy挂墙式花洒shower caddy花洒
soap dish皂碟
paper towel storage container Paper handkerchief box纸巾盒safety grab bar 安全扶杆
tooth brush holder 牙刷架
mirror镜子
corner shelf 转角架
stainless steel push down
bin 不锈钢脚踩垃圾桶
column basin立柱盆
desk basin台盆
bathtub浴缸
Butt joint对接接头
basket 篮子
bath towel 浴巾
bathrobe 浴袍
bathtub 浴缸
四、马桶（toilet）
按种类分
pan大便器
squatting 蹲式便器
sitting 坐式便器
wash down 冲落式便器siphonic 虹吸式便器
siphon jet 喷射虹吸式便器siphon vortex 旋涡虹吸式便器integral sitting 连体式坐便器urinal小便器
wall hung urinal壁挂式小便器stall urinal落地式小便器
One-Piece Toilet 连体座便器Two-piece toilet 分体座便器相关配件
toilet, lavatory 恭桶
五金工具英语词汇toolbox 工具箱 bench 工作台 vice, clamp 虎钳（美作：vise） saw 锯 bow saw 弓锯 circular saw 圆锯（美作：buzzsaw）compass saw, scroll saw 钢丝锯 fretsaw 细锯 handsaw 手锯 chisel 口凿 cold chisel, burin 冰凿 gouge, firmer gouge 半圆凿 plane 刨子 moulding plane 型刨 jack plane 粗刨 rabbet plane 槽刨 drawknife 刮刀 scraper 三角刮刀 rasp 粗锉 file 锉 square 尺
miter 斜槽规 scriber 近线尺 set square, triangle 三角板brace 手拉曲柄锉 hand drill 手钻 drill, bit 钻，有柄钻 gimlet, auger 钻，无柄钻countersink 锥口钻 gauge, marking gauge 量规hammer 锤 mallet 木槌 nail 钉 brad 平头钉 tack, stud 圆头钉 screw 螺丝钉 screwdriver 螺丝刀，改锥screw tap 螺丝攻 nail puller 拔钉器 ruler 尺 tape measure 卷尺 folding ruler 折尺sandpaper, emery paper 砂纸
toolbox 工具箱 bench 工作台 vice, clamp 虎钳（美作：vise） saw 锯 bow saw 弓锯 circular saw 圆锯（美作：buzzsaw）compass saw, scroll saw 钢丝锯fretsaw 细锯 handsaw 手锯 chisel 口凿 cold chisel, burin 冰凿 gouge, firmer gouge 半圆凿 plane 刨子 moulding plane 型刨 jack plane 粗刨 rabbet plane 槽刨 drawknife 刮刀 scraper 三角刮刀 rasp 粗锉 file 锉 square 尺 miter 斜槽规
课程关键术语中英文对照表 1、Software 软件 2、U ser 用户 3、s oftware engineering 软件工程 4、D ocument 文档 5、D ata 数据 6、S oftware Crisis 软件危机 7、S oftware Engineering 软件工程 8、M aintenance 维护 9、B ug 故障 10、Correctness 正确性 11、Reliability 可靠性 12、IDE 集成开发环境 13、Maintainability 可维护性 14、Reusability 可重用性 15、Traceability 可跟踪性 16、Portability 可移植性 17、Interoperability 互操作性 18、Efficiency 有效性 19、Abstract 抽象 20、Modularity 模块化 21、Information Hiding 信息隐藏
23、Consistency 一致 24、Completeness 完整 25、Verifiability 可验证 26、Software Lifecycle 软件生命周期 27、Feasibility Investigation 可行性分析 28、Requirement 需求 29、Requirement Analysis 需求分析 30、Software Delivery 软件发布 31、Prototype 原型 32、Software Requirement Specification (SRS) 软件需求规格说明书 33、Software Architecture 软件体系结构 34、software development 软件开发 35、unit testing 单元测试 36、Integration Test Plan 集成测试计划 37、Detailed Design 详细设计 38、Unit Test Plan 单元测试计划 39、Integration Test 集成测试 40、Integration Test Report 集成测试报告 41、Software Process 软件过程 42、Software Process Model 软件过程模型 43、Incremental Model 增量模型
Normteile标准件 Gewinde, Schrauben, Muttern螺纹、螺栓、螺母 Gewinde螺纹 Schrauben螺栓 Gewindeausl?ufe螺纹收尾、肩距 Gewindefreistiche螺纹退刀槽 Senkungen锪孔、沉孔 Mutter螺母 Scheibe档圈 Schlüsselweite扳手口尺寸 Werkzeugvierkante工具四方柄 Stifte, Bolzen, Niete, Mitnehmerverbindung Stifte 圆柱销 Kerbstifte弹性销 Bolzen轴销 Keile 键 Federn弹簧 Keilwellenverbindung花键连接 Blindniete抽芯铆钉 Werkzeugkegel刀具、工具锥度 Normteile für Vorrichtungen und Standzwerkzeuge工装夹具和冲裁模具的标准件 Normteile für Vorrichtungen工装夹具的标准件 T-NutenT型槽 Kugelscheiben球面垫圈 Normteile für Stanzwerkzeuge冲裁模具标准件 Federn弹簧 Antriebstechnik传动技术 RiementriebeV型带传动
Gleitlagerbuchsen滑动轴承轴瓦 W?lzlager滚动轴承 Nutmuttern圆螺母 Passscheiben配合垫圈 Stützscheiben调整垫圈 Wellenenden轴端 Wellendichtring轴用密封件 RunddichtringO型密封圈 机械工具 Mechanic“s Tools spanner 扳子 (美作:wrench) double-ended spanner 双头扳子 adjustable spanner, monkey wrench 活扳子,活络扳手box spanner 管钳子 (美作:socket wrench) calipers 卡规 pincers, tongs 夹钳 shears 剪子 wire cutters 剪线钳 multipurpose pliers, universal pliers 万能手钳
Lecture 1 An Introduction to Software Engineering 1 what does software engineering concern? 1) Software engineering is concerned with theories, methods and tools for professional software development. 2) Software engineering is concerned with cost-effective software development. 2 What is software? Software includes: ①computer programs ②data structures ③documents 3 What is the two types of software products Generic software(通用软件) and custom software（定制软件） 4 The three key elements of a successful software project are: on time, within budget, satisfies the user’s needs 5 Generic activities in all software processes are: Specification（描述）, Development（开发）, Validation（有效性验证）, Evolution （进化） 6 The attributes of good software include: Maintainability（可维护性）, Dependability（可依赖性）, Efficiency（有效性）, Acceptability（可接受性）
中英文对照外文翻译 (文档含英文原文和中文翻译) Application Fundamentals Android applications are written in the Java programming language. The compiled Java code — along with any data and resource files required by the application — is bundled by the aapt tool into an Android package, an archive file marked by an .apk suffix. This file is the vehicle for distributing the application and installing it on mobile devices; it's the file users download to their devices. All the code in a single .apk file is considered to be one application. In many ways, each Android application lives in its own world: 1. By default, every application runs in its own Linux process. Android starts the process when any of the application's code needs to be executed, and shuts down the process when it's no longer needed and system resources are required by other applications. 2. Each process has its own virtual machine (VM), so application code runs in isolation from the code of all other applications. 3. By default, each application is assigned a unique Linux user ID. Permissions are set so that the application's files are visible only to that user and only to the application itself — although there are ways to export them to other applications as well. It's possible to arrange for two applications to share the same user ID, in which case they will be able to see each other's files. To conserve system resources, applications with the same ID can also arrange to run in the same Linux process, sharing the same
常用工具中英文对照 扳手Wrenches/套筒Sockets 开口扳手 Open End Wrenches 梅花扳手 Spline End Wrenches 块扳手 Crowfoot Wrenches 开口/梅花扳手 Combination Wrenches 内六角扳手 Hex Wrenches 平板棘轮扳手 Slab Ratchet 棘轮扳手 Ratchet Wrenches 力矩扳手 Torque Wrenches 管钳 Pipe Wrenches 活动扳手 Adjustable Wrenches 六角套筒 Six Point Sockets 梅花套筒 Twelve Point Sockets 万向套筒 Universal Sockets 转接头 Adaptor 套筒接杆 Socket Extension 万向转接头 Universal Joint 螺刀Screwdrivers 快速螺刀 Fast Screwdrivers 仪表螺刀 Electronic miniature Screwdrivers
十字头螺刀 PILLIPS Screwdrivers 磁性螺刀 Magnetic Screwdrivers 一字头螺刀 Flat Tip Screwdrivers 摇把 Speeders 钳Pliers 尖嘴钳 Needle Nose Pliers 大力钳 Locking Pliers 保险丝钳 Safety Wire Twisters 鹰嘴钳 Adjustable Joint Pliers 插头钳 Connector Plug 剥线钳 Wire Strippers 鱼口钳 Combination Slip-Joint Pliers 卡环钳 Convertible Snap Ring Pliers 剪线钳 Diagonal Cutters 压线钳 Wire Crimpers 电气工具Electronic Tools 矿灯 Safety Lamb (Mine r’s Lamb) 手电 Flashing Light 对讲机 Interphone 电烙铁 Electronic Iron 耳机 Earphone 防静电手腕 Static Wrist
冲压工具stamping tool 冲压法pressing 冲击impact 冲击强度impact strength 冲击测试impact test 冲锻法;锤锻法;模锻法drop forging 去毛边trimming 粗糙度roughness 光滑的smooth 法兰盖blind flange, blind 阀体body 阀盖bonnet 气缸(或液压缸)操纵的cylinder operated 碳素钢carbon steel (CS) 低碳钢low-carbon steel 中碳钢medium-carbon steel 高碳钢high-carbon steel 普通碳素钢general carbon steel 优质碳素钢high-quality carbon steel 普通低合金结构钢general structure low-alloy steel 合金结构钢structural alloy steel 合金钢alloy steel
低合金钢low alloy steel 中合金钢medium alloy steel 高合金钢high alloy steel 耐热钢heat resisting steel 高强度钢high strength steel 复合钢clad steel 工具钢tool steel 弹簧钢spring steel 钼钢molybdenum steel 镍钢nickel steel 铬钢chromium steel 铬钼钢chrome-molybdenum steel 铬镍钢chromium-nickel steel,chrome-nickel steel 不锈钢stainless steel (S.S.) 奥氏体不锈钢Austenitic stainless steel 马氏体不锈钢Martensitic stainless steel 司特来合金(钨铬钴台金) Stellite 耐蚀耐热镍基合金Hastelloy 铬镍铁合金inconel 耐热铬镍铁合金incoloy 20合金20 alloy 平炉钢(马丁钢) Martin steel
Part 1 Overview Chapter 1 Introduction 1.1 FAQs about software engineering 1.2 Professional and ethical responsibility Chapter 2 Socio-technical systems 2.1 Emergent system properties 2.2 Systems engineering 2.3 Organisations, people and computer systems 2.4 legacy systems Chapter 3 Critical systems 3.1 A simple safety-critical system 46 3.2 System dependability 47 3.3 Availability and reliability 51 3.4 Safety 55 3.5 Security 58 Chapter 4 Software processes 4.1 Software process models 65 4.2 Process iteration 71 4.3 Process activities 74 4.4 The Rational Unified Process 82 4.5 Computer-Aided Software Engineering 85 Chapter 5 Project management 92 5.1 Management activities 94 5.2 Project planning 96 5.3 Project scheduling 99 5.4 Risk management 104 Requirements Chapter 6 Software requirements 6.1 Functional and non-functional requirements 6.2 User requirements 6.3 System requirements 6.4 Interface specification 6.5 The software requirements document Chapter 7 Requirements engineering processes 7.1 Feasibility studies 7.2 Requirements elicitation and analysis 7.3 Requirements validation 7.4 Requirements management Chapter 8 System models 8.1 Context models 8.2 Behavioural models 8.3 Data models 8.4 Object models 8.5 Structured methods Chapter 9 Critical systems specification 9.1 Risk-driven specification 9.2 Safety specification 9.3 Security specification 9.4 Software reliability specification Chapter 10 Formal specification 10.1 Formal specification in the software process 10.2 Sub-system interface specification 10.3 Behavioural specification Part 3 Design Chapter 11 Architectural design 11.1 Architectural design decisions 11.2 System organisation 11.3 Modular decomposition styles 11.4 Control styles 11.5 Reference architectures Chapter 12 Distributed systems architectures 12.1 Multiprocessor architectures 12.2 Client-server architectures 12.3 Distributed object architectures 12.4 Inter-organisational distributed computing Chapter 13 Application architectures 13.1 Data processing systems 13.2 Transaction processing systems 13.3 Event processing systems 13.4 Language processing systems Chapter 14 Object-oriented design 14.1 Objects and object classes 14.2 An object-oriented design process 14.3 Design evolution Key Points Further Reading Exercises Chapter 15 Real-time software design
测量工具中英文对照表大全 测量工具中英文对照表 heodolite 经纬仪 Water Level 水位仪 Level Ruler 水平尺Casing gradienter Coating thickness Measurer 涂层测厚仪 Ultrasonic thickness measurer 超声波测厚仪 Ultrasonic crack detector 超声波裂纹测试仪 Digital thermometer 数字温度计 radiation thermometer 辐射温度计 Gradient Reader 坡度读数器 Volometer 万用表MegaOhmmeter 兆欧表 Earthing resistance Reader 接地电阻读数表Plug gauge 圆柱塞规Magnifying glass 放大镜Plummet 铅锤Profile projector 投影仪 Pin Gauge 针规(不知道和plug gauge 的区别在哪里,知道的请指正) Gauge block 块规 Bore gauge 百分表 A vernier caliper 游标卡尺 Coordinate Measureing Machine(CMM) 三尺元 Pressure gague寸压力计 电度厚度测试仪(Electroplating THK.Tester) 转(扭)力仪(Twisting Meter) 螺纹规(Thread Gauge) 块规(Block Gauge) 环规(Ring Gauge) 力矩计(Torque Meter) 塞规(Plug gage) 高度仪(Altitude gauge) 塞尺/间隙规(Clearance gauge) 千分卡尺(Micrometer Calipers ) “过” -- “不过” 验规(通-止规) [go-no-go gauge] 游标卡尺(Vernier Caliper) 电子卡尺(Digital caliper)
厨柜英语Kitchen Cabinet English 地柜Base cabinet/Unit 吊柜Wall cabinet/Unit 高柜Tall cabinet/Unit 半高柜Semi-tall cabinet 其它miscellaneous 灯具light 水槽sink 电器appliances 水龙头Faucet 下水器bottle tap 封板filler panel 双层餐具2-tier cutlery tray 垃圾桶waste bin 垃圾篮cleaning material basket 层板粒supports 上翻门flap-up door 灯具变压器transformer for integrated light 转向灯变压器transformer for volatage halogen 拉篮pull-out basket 见光贴面finished side 吊轨mounting track 喷口pull-out spout 微波炉microwave 烤箱oven 油烟机chimney hood 燃气炉burner 电磁炉ceramic hob 结构： 屋顶roofing 墙面fasade 台面Counter top 直径Diameter 后面Rear 底部Base 平面Plan 立面Elevation 侧面Side Elevation 背面Back Elevation 平面图Floor Plan 正面图Front Elevation 立面图Sectional Elevation 折角Dog Ear 灯线Light/lamp kick 脚线Toe kick 脚线高度Toe height 配同门板色脚线concolor toe kick 柜子前边缘Carcase Front Edge 中间开Center separate 板材： 原木lumber 实木solid wood 橡木oak 桦木birch 橡胶木Rubber wood 贴橡木皮oak veneer 夹板，胶合板Plywood 爱家板MFC board 中纤板MDF Board 海木板Seawood board 防火板Fireproof board 防潮板Damp proof board 刨花板(PB) Particle board / Chipboard PVC吸塑PVC Membrane 平板flat sheet 波形板roofing sheet 门板Door Panel 顶板 /天板Top Panel/Board 面板Faceplate 前板Front Panel 侧板Side Panel 背板Back Panel / Rear Panel 底板Base Panel / Bottom Board 加高侧板The raised Box Side 名牌Name plate 层板Shelf Board 活板Movable Board 固定板Fix Board 补强板Support Board 直边板Wood end panel 支撑挂板Support Plate 裙角Bottom Front Board 桶侧Drawer Side Board 桶尾Drawer Back Board 桶里板Drawer Inner Board 抽屉面/桶面/桶头Drawer Front Panel 灯板lamp panel 见光Exposed panel 假门Fake Door Panel 假门板Fake panel
门控五金专业术语 Terminologies for door control hardware 一、地弹簧Floor hinge （Floor spring）Adjustable creep speed 缓行速度 Adjust detection sensibility 检测灵敏度调整Adjustment style 调速方式 Two-section adjustment 两端调节 Buffer 缓冲区 Closing section 关门阶段 Opening section 开门阶段 Center pivoted arm 中心摇臂 Top pivot seat 上枢轴座 Pivot bottom seat 枢轴底座 Offset pivot arm 偏心摇臂 Closing force 紧闭力 Closing speed 闭门运行速度 Opening speed 开门运行速度 Non-hold 无驻持 Hold 驻持 Economic model 经济型 Floor hinge （Floor spring）地弹簧 Hydraulic control 液压控制 Cover plate. 盖板 Cam spindle 凸轮轴 Sealing compound 密封化合物 Environmental-Protection floor hinge 环保型地弹簧Insect prevention 防虫 Water proof 防水 Keep warm 保温 Antirust 防锈 Maximum opening angle 最大开启角度 Maximum loading 最大门重 Maximum loading capacity 最大承重 Maximum opening force 最大开门力 Non-antomatic pivot hinge 地轴 Pivot hinge 地轴 Door axial 门轴 Top pivot 顶轴 Upper pivot 上轴 Adjust gasket 调整垫片 Bottom Pivot 下轴 二、玻璃门夹、驳接件、铰链类
五金相关词汇中英文对 照 Normteile 标准件 Gewinde, Schrauben, Muttern 螺纹、螺栓、螺母 Gewinde 螺纹 Schrauben 螺栓 Gewindeauslufe 螺纹收尾、肩距 Gewindefreistiche 螺纹退刀槽 Senkungen 锪孔、沉孔 Mutter 螺母 Scheibe 档圈 Schl tsselweite 扳手口尺寸 Werkzeugvierkante 工具四方柄 Stifte, Bolzen, Niete, Mitnehmerverbindung Stifte 圆柱销 Kerbstifte 弹性销 Bolzen 轴销 Keile 键 Federn 弹簧 Keilwellenverbindung 花键连接 Blindniete 抽芯铆钉 Werkzeugkegel 刀具、工具锥度 Normteile f r Vorrichtungen und Standzwerkzeuge 工装夹具
和冲裁模具的标准件 Normteile f r Vorrichtungen工装夹具的标准件 T-NutenT 型槽 Kugelscheiben 球面垫圈 Normteile f r Stanzwerkzeuge 冲裁模具标准件 Federn 弹簧 Antriebstechnik 传动技术 RiementriebeV 型带传动 Gleitlagerbuchsen 滑动轴承轴瓦 W?lzlager 滚动轴承 Nutmuttern 圆螺母 Passscheiben配合垫圈 St t tzscheiben 调整垫圈 Wellenenden 轴端 Wellendichtring 轴用密封件 RunddichtringO 型密封圈 机械工具Mechanic“s Toosl spanner 扳子（美 作:wrench） double-ended spanner 双头扳子adjustable
常见职务，职位英文译名 Accounting Assistant 会计助理 Accounting Clerk 记帐员 Accounting Manager 会计部经理 Accounting Stall 会计部职员 Accounting Supervisor 会计主管 Administration Manager 行政经理Administration Staff 行政人员 Administrative Assistant 行政助理Administrative Clerk 行政办事员 Advertising Staff 广告工作人员 Airlines Sales Representative 航空公司定座员Airlines Staff 航空公司职员 Application Engineer 应用工程师 Assistant Manager 副经理 Bond Analyst 证券分析员 Bond Trader 证券交易员 Business Controller 业务主任 Business Manager 业务经理 Buyer 采购员 Cashier 出纳员 Chemical Engineer 化学工程师 Civil Engineer 土木工程师 Clerk/Receptionist 职员/接待员 Clerk Typist & Secretary 文书打字兼秘书Computer Data Input Operator 计算机资料输入员Computer Engineer 计算机工程师 Computer Processing Operator 计算机处理操作员Computer System Manager计算机系统部经理Copywriter广告文字撰稿人 Deputy General Manager副总经理 Economic Research Assistant经济助究助理Electrical Engineer电气工程师 Engineering Technician工程技术员 English Instructor/Teacher英语教师 Export Sales Manager外销部经理 Export Sales Staff外销部职员 Financial Controller财务主任 Financial Reporter财务报告人 F.X. (Foreign Exchange)Clerk外汇部职员 F.X. Settlement Clerk外汇部核算员 Fund Manager财务经理 General Auditor审计长 General Manager/ President总经理 General Manager Assistant总经理助理 General Manager's Secretary 总经理秘书
烘焙设备和工具中英文对照冰箱refrigerator, ice box 冰柜、冷冻柜freezer 抽屉式冷柜locker 打蛋机egg beater, beating machine 电炉electric stove 电磁炉electromagnetic oven 发酵箱fermentation room 滚圆机rounder 和面机dough mixer 搅拌器mixer 绞肉机mincing machine, meat grinder 烤炉oven 转炉revolving oven 风车转炉reel oven 链条烤盘式平炉traveling chain oven 钢带式平炉band oven 螺旋式烤炉spiral oven 托盘式炉tray oven 箱式烤炉deck oven 辊切成型机rotary cutter 挤条成型机route press
钢丝切割成型机wire cutter 挤浆成型机depositor 面团拌和机pastry blender 面包整形机moulder 奶油分离器cream separator 食品加工器food processor 食品切碎机food chopper 食品粉碎机masher 洗碗机dish washer 醒发室prover 榨汁机juice extractor, squeezer 油炸机deep-fryer 剥皮器zester 磅秤scale 保鲜纸locker paper 裱花转台revolving cake stand 焙烤用纸碟baking cup 布丁模pudding mold 叉子fork 秤scale 长柄平底煎锅skillet 长筷chopsticks
冲压工具 stamping tool 冲压法 pressing 冲击 impact 冲击强度 impact strength 冲击测试 impact test 冲锻法;锤锻法;模锻法 drop forging 去毛边 trimming 粗糙度 roughness 光滑的 smooth 法兰盖 blind flange, blind 阀体 body 阀盖 bonnet 气缸(或液压缸)操纵的 cylinder operated 碳素钢 carbon steel (CS) 低碳钢 low-carbon steel 中碳钢 medium-carbon steel 高碳钢 high-carbon steel 普通碳素钢 general carbon steel 优质碳素钢 high-quality carbon steel 普通低合金结构钢 general structure low-alloy steel 合金结构钢 structural alloy steel 合金钢 alloy steel 低合金钢 low alloy steel 中合金钢 medium alloy steel 高合金钢 high alloy steel 耐热钢 heat resisting steel
高强度钢 high strength steel 复合钢 clad steel 工具钢 tool steel 弹簧钢spring steel 钼钢 molybdenum steel 镍钢 nickel steel 铬钢 chromium steel 铬钼钢 chrome-molybdenum steel 铬镍钢 chromium-nickel steel,chrome-nickel steel 不锈钢 stainless steel .) 奥氏体不锈钢 Austenitic stainless steel 马氏体不锈钢 Martensitic stainless steel 司特来合金(钨铬钴台金) Stellite 耐蚀耐热镍基合金 Hastelloy 铬镍铁合金 inconel 耐热铬镍铁合金 incoloy 20合金 20 alloy 平炉钢(马丁钢) Martin steel 镇静钢 killed steel 半镇静钢 semi-killed steel 沸腾钢 rimmed steel; rimming steel; open-steel 锻钢 forged steel 铸钢 cast steel 铸铁 cast iron .) 灰铸铁 grey cast iron 可锻铸铁 malleable iron (MI)
常用钢材理论重量表 [2004-12-22 8:51:47] 计算公式： t（重量kg) = A(断面积mm²)×L(长度m) ×p(密度g/cm³) ×1/1000 注：(1) 型材制造中有允许偏差值，故上式只做估算之用。 (2) 关于p值,钢材通常取7.85 . 螺丝产品名称中英文对照（台湾版）螺丝螺 [2004-12-22 8:51:24] 六角螺絲(栓) HEX HEAD CAP SCREWS(HEX BOLTS) 六角機械螺絲HEX HEAD MACHINE BOLTS 六角木牙螺絲HEX LAG BOLTS 四角螺絲SQUARE HEAD BOLTS T頭螺絲T HEAD BOLTS 馬車螺絲CARRIAGE BOLTS 環首螺絲EYE BOLTS 內六角孔螺絲HEX SOCKET CAP SCREWS 固定螺絲SET SCREWS 螺椿栓STUD BOLTS 螺旋椿SCREW STUDS 輪殼螺栓WHEEL BOLTS 翼形螺絲WING SCREWS 自攻螺絲SELF TAPPING SCREWS 自削螺絲THREAD CUTTING SCREWS 鑽尾螺絲SELF DRILLING SCREWS 旋入螺絲DRIVE SCREWS 機械螺絲MACHINE SCREWS 木螺絲WOOD SCREWS 家具螺絲FURNITURE SCREWS 塑板螺絲CHIPBOARD SCREWS 牆用螺絲DRYWALL SCREWS 基礎螺栓FOUNDATION BOLTS U型螺栓U BOLTS 勾頭螺栓HOOK BOLTS 套掛螺絲TOGGLE BOLTS 突緣螺絲FLANGE BOLTS 軌道螺栓(魚尾螺絲) TRACK BOLTS 耐候鋼螺絲CORTEN STEEL HEA VY HEX BOLTS 扭矩控制螺栓T.C.BOLTS
计算机软件编程英语词汇集锦（转载） Access Control List（ACL）访问控制列表access token 访问令牌 account lockout 帐号封锁 account policies 记帐策略 accounts 帐号 adapter 适配器 adaptive speed leveling 自适应速率等级调整Address Resolution Protocol(ARP) 地址解析协议Administrator account 管理员帐号 ARPANET 阿帕网（internet的前身） algorithm 算法 alias 别名 allocation 分配、定位 alias 小应用程序 allocation layer 应用层 API 应用程序编程接口 anlpasswd 一种与Passwd+相似的代理密码检查器applications 应用程序 ATM 异步传递模式 attack 攻击 audio policy 审记策略 auditing 审记、监察 back-end 后端 borde 边界 borde gateway 边界网关 breakabie 可破密的 breach 攻破、违反 cipher 密码 ciphertext 密文 CAlass A domain A类域 CAlass B domain B类域 CAlass C domain C类域 classless addressing 无类地址分配 cleartext 明文 CSNW Netware客户服务 client 客户，客户机
client/server 客户机/服务器 code 代码 COM port COM口（通信端口） CIX 服务提供者 computer name 计算机名 crack 闯入 cryptanalysis 密码分析 DLC 数据链路控制 decryption 解密 database 数据库 dafault route 缺省路由 dafault share 缺省共享 denial of service 拒绝服务 dictionary attack 字典式攻击 directory 目录 directory replication 目录复制 domain 域 domain controller 域名控制器 domain name 域名 域名其实就是入网计算机的名字，它的作用就象寄信需要写明人们的名字、地址一样重 要。域名结构如下：计算机主机名.机构名.网络名.最高层域名。域名用文字表达，比 用数字表达的IP地址容易记忆。加入Internet的各级网络依照DNS的命名规则对本网内 的计算机命名，并负责完成通讯时域名到IP地址的转换。 DNS 域名服务器 DNS(Domain Name System,域名系统)是指在Internet上查询域名或IP地址的目录服务系 统。在接收到请求时，它可将另一台主机的域名翻译为IP地址，或反之。大部分域名系 统都维护着一个大型的数据库，它描述了域名与IP地址的对应关系，并且这个数据库被 定期地更新。翻译请求通常来自网络上的另一台计算机，它需要IP地址以便进行路由选择。DDE 动态数据交换 DHCP 动态主机配置协议 encryption 加密 EGP 外部网关协议 FDDI 光纤分布式数据接口 FAT 文件分配表 FTP(File Transfer Protocol）文件传送协议 filter 过滤器 firmware 固件