电动吸尘器操作规程一、前言电动吸尘器是一种方便清洁家居、办公场所的工具，使用前需了解其操作规程，以确保安全使用和有效清洁。
本文将详细介绍电动吸尘器的操作指南，帮助用户正确使用该设备。
二、设备准备1. 检查电源插座：确保插座与电动吸尘器的电源线连接牢固，无松动或插头变形的情况。
2. 检查吸尘器袋：确认吸尘器袋安装正确，无破损或堵塞。
3. 检查滤芯：检查滤芯是否清洁，无异味或损坏。
三、操作流程1. 打开电源：将电源线插入电源插座，并打开电源开关。
2. 调整吸力：根据清洁对象的性质，选择合适的吸力档位。
通常，地毯和沙发等需要较高吸力，而薄纱窗帘和书架等则需要较低吸力。
3. 启动吸尘器：按下启动按钮，确保电动吸尘器正常工作。
4. 移动操作：将吸尘器头平稳贴近清洁对象的表面，以直线或环绕式方式移动吸尘器头，确保完成对整个区域的清洁。
5. 转向操作：当需要转向时，先停止吸尘器运行，再将吸尘器头转向所需方向，避免在移动中强行改变方向。
6. 收纳电源线：使用完毕后，将电源线缠绕整齐，并存放在吸尘器的电源线收纳器内，防止松散的电源线绊倒行人。
四、使用注意事项1. 避免过度使用：长时间连续使用电动吸尘器可能导致设备过热，建议每小时使用不超过30分钟，中途需要适当休息和散热。
2. 防止吸尘器过载：定期清空吸尘器袋，避免堵塞。
在吸尘器袋接近容量极限时，及时更换或清空袋子。
3. 清洁过滤系统：定期清洁滤芯，避免滤芯堵塞影响吸力。
具体清洁方法请参考电动吸尘器说明书。
4. 避免吸入液体：电动吸尘器只适用于干燥的清洁对象，切勿用于吸取液体，以免损坏设备。
5. 安全存放：使用完毕后，请将吸尘器存放在干燥通风处，避免阳光直射或潮湿环境，以延长使用寿命。
五、安全警示1. 儿童禁用：禁止儿童在无成人监护下使用电动吸尘器。
2. 避免触电：不得将电动吸尘器插头接触水或潮湿的手部。
在插拔电源线时，请务必先关闭电源开关。
3. 停止操作：在清理吸尘器头或其他部件时，请先断开电源，并确保设备完全停止运作。
User ManualImportant Safety InstructionsTo reduce the risk of injury or damage, keep these safety precautions in mind when setting up, using and maintaining your robot vacuum cleaner:Read all safety and operating instructions before operating your robot. Retain the safety and operating instructions for future reference.Pay attention to all warnings on your robot, battery, charging dock and in the user manual.Follow all operating instructions.The external cable or cord of the power supply unit can not be replaced; if the cord or plug is damaged, the power supply unit shall be disposed of.This product is designed to be plugged into a standard outlet only. Product may not be used with any type of power converter. Use of power converters will immediately void the warranty.CAUTION: Only charge one of the following robot batteries: maximum 14.4V, max 2600mAh Ni-MH or maximum 2600mAh Li-ion battery. Other type of batteries may burst and cause injuries. Please contact Customer Care for the correct replacement of your battery.Please charge and remove the battery from your robot and accessories before long-term storage or transportation.The battery must be removed from this device before this device is disposed of. To remove the battery from this device, first remove the screws on the bottom, then remove the main PCB and unscrew the battery cover by using a screwdriver. Remove the battery by disconnecting the quick connector. WARNING: Chemical Exposure: If the battery pack is leaking, do not allow the liquid to come in contact with skin or eyes. If contact has been made, wash the affected area with copious amounts of water and seek medical advice. Place the battery (the used battery pack included when the robot will be disposed) in a sealed plastic bag and dispose of safely according to local environmental regulation. WARNING: Fire or Explosion Hazard: Do not crush or dismantle battery packs. Do not heat or place the battery pack near any heat source or direct sunlight. Do not incinerate or short-circuit the battery pack. Do not subject batteries to mechanical shock.Contact your local waste management authority for battery recycling and disposal regulations in your area.Your robot is not a toy. Do not sit or stand on robot. Children and pets should be supervised when your robot is operating.Robot is for indoor use only.Do not use non-rechargeable batteries. Use the rechargeable battery provided with the product only. For replacement, purchase identical robot batteries or contact robot Customer Care for alternative battery options.Store and operate the robot in a room with moderate temperatures only.Do not spray or pour liquids on your Robot.Do not use any other power supply cord. For replacement cords, please contact Customer Care to ensure proper selection of country-specific power supply cord. Do not use the robot to pick up sharp objects, glass, or anything that is burning or smokingDo not immerse the battery pack in any liquid.Do not use the robot to pick up spills of water bleach, paint, or other chemicals, or anything wet.Picking up objects like clothing, loose papers, pull cords for blinds or curtains, power cords, and any fragile objects before using the robot. If the robot passes over a power cord and drags it, objects on table or shelves are likely to fall off.If the room to be cleaned contains a balcony, a physical barrier should be used to prevent access to the balcony and ensure safe operation.Do not place anything on top of your robot.Be aware that the robot moves on its own. Take care when walking in the area that the robot is operating in to avoid stepping on it.Do not operate the robot in areas with exposed electrical outlets on the floor. Do not use this device on an unfinished, unsealed, waxed or rough floo. It may cause damage to the floor and this device. Use only on hard floor surfaces or low pile carpets.This device has been designed to be used on floors without scratching them. We still recommend that you test this device on a small area of the room to be cleaned to ensure no scratches are made before cleaning the whole room.If storing robot off the charging dock, remove the battery first. Then store robot and the battery in a cool, dry place.The symbol on the product or its packaging indicates:Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities. Contact your local authority for information regarding the collection systems available. If electrical appliances are disposed of in landflls or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging your health and well-being. Please contact your local or regional waste authority for more information on collection, reuse and recycling programs.Battery and Charging Information Lithium-ion Battery Battery Storage Important: Lithium-ion batteries and products that contain Lithium-ion are subject to stringent transportation regulations. If you need to ship this product (with the battery included) for service, travel or any other reason, you MUST comply with the following shipping instructions:Remove the Lithium-ion battery from the product.Place a piece of tape over the battery's metal charging contacts.Reinstall the battery (with the tape on it) in the product and secure the battery door.Package the product in its original packaging or in your own packaging that prevents any movement during transportation.Ship via ground transportation only (no air shipping).1. Robot About Your RobotAuto cleaning Start/Stop button Press and hold on to Power On/0ff; Press to start cleaning.Auto-recharging button2. Accessories3. Charging Dock1 x Boundary Strips Charging Indicator 1 x Mop(with 2xAAA batteries)1 x Brush 1 x Water Tank 1 x Charging Dock4. Remote Control5. LED IndicatorUsing Your RobotQuick Start Note: If you don't put the cable into the trunking, it may stuck the robot while charging or cleaning.1) Place the charging dock on a hard, level surface and against a wall.Attach side brushes to the bottom of robot by pressing a brush into each slot.area leaving at least.charging dock and the other end into a wall outlet.Note: Please make sure the the indicator light is on when the charging dock is plugged in, otherwise the robot can not be charged.dock.Plug in the charging dock, and Put the cable into the trunking at the bottom of charging dock.Charging Dock Position Install Side BrushesPlace the robot on the charging dock, making sure the metal charging contacts on the charging dock match up with those underneath the robot. If successful, you will hear a series of tones.the robot.Activate the RobotPress the power button once to wake up the robot.Press the power button again or press the “ ” button on remote controlPause press the button or press the “ ►II ” To start the robot, press the button or press the “ ►II ”control.Power OFF standby mode, press and hold theWhen you select spot cleaning, robot intensely cleans a localized area by spiraling outward about 3 feet (1 meter) in diameter and then spiraling inward to where it started. During spot cleaning, robot boosts vacuum power to ensure theSpot CleaningPower levels Warm Tips: During the recharging process, there may be a phenomenon that the charging dock cannot be found. At this time, the robot will flash red light and "BEEP" four times. Please manually put the robot onto the charging dock to charge.How Robot Clean Your HomePress the button on robot or press the “ ” button on remote control to If the battery is low while the cleaning is not finished, the robot will return to the charging dock for charging.• When the robot vacuum cleaner is in sweeping mode, press this button to adjust the suction power;• When the robot vacuum cleaner is in sweeping and mopping simultaneous mode, press this button to adjust the suction power;• When the robot vacuum cleaner is in mopping mode, press this button toSingle Room CleaningFloor Mopping CleaningEdge CleaningAfter the robot finishes cleaning the open areas of your floor, it enables edge cleaning mode to ensure that it has cleaned along walls and around furniture Legs. If you prefer a quicker edge cleaning, press the “ ” button on remote control.the Robot is equipped with a water tank so that it can clean your home in the mopping mode• Attach the cloth and fill in the water tank with water.• Remove the dust bin.• Put the water tank back and start the robot.Note: If you are using the dry-sweeoing mode, skip the step offillingwater. Press the button “ ” on the remote control to start random cleaning. Warm Tips:In this mode, the robot will keep cleaning for about 30 minutes and then stop. Please close the door to ensure the robot will not go out the room.Set the Remote Control' s ClockCleaning ScheduleRobot has cleaning schedule settings which allow you to customize when Robotcleans your home.Press the button on remote control, and then the hour section begins Press the “ ” or “ ” button to select the minute or hour section. Press “ ” or “ ” button to select the desired figures.And then press the “ ” button, the robot will "BEEP" when the clock setting is completed.Set the Remote Control' s ClockPress the “ ” button on remote control, and then the hour section begins to hash in the cleaning schedule display setting window.Press the “ ” or “ ” button to select the minute or hour section. Press “ ” or “ ” button to select the desired figures.And then press the “ ” button, the robot will "BEEP" when the cleaning schedule setting is completed.Regular Robot CareCancel the Cleaning SchedulePlease perform the following care procedures to keep the robot running at its peak performance. If you notice the robot picking up less debris from your floor, then empty the bin, clean the filter and rolling brush.Recommended cleaning /replacement frequency:Press and hold the “ ” button approximately 4 seconds on the remotecontrol, the robot will "BEEP" when the cleaning schedule process is canceled.Press bin release button to Open the bin's door to empty it.Empty the Robot's BinRemove the filter by grasping the white tab.Shake off debris by tapping the filter Clean the rolling brush. Cut off the hair winded in the rolling brush with the knife of providedRemove the side brush, use a cloth to remove the dust from the brush.Clean the Robot' s Rolling Brush, Side Brush, Swivel Wheel and SensorsClean the Robot's FilterTake out the rolling brush, clean the vacuuming aisle with a cloth.the problem is not resolved, please contact our COST FREE customer service team for further assistance.Warm Tips: Some errors can be resolved by rebooting the robot. To reboot the robot, press the power button on the bottom of the robot, you will hear an audible tone signifying a successful reboot.After-Sale ServiceThe professional customer service team from Ultenic will be responsible and provide support to all products that come with a worry-free warranty for one year automati-cally after purchase.Please contact Ultenic Support and Service via Email below.ULTENIC UK LTD71-75 Shelton Street, Covent Garden, London, WC2H 9JQultenic__official UltenicOfficial Ultenic_Official Ultenic_Official。
吸尘器操作规程引言概述：吸尘器是我们日常清洁工作中常用的电器设备之一。
正确的操作吸尘器不仅能提高清洁效果，还能延长设备的使用寿命。
本文将详细介绍吸尘器的操作规程，匡助大家正确、安全地使用吸尘器。
一、准备工作1.1 检查吸尘器设备：确保吸尘器设备完好无损，无松动、破损或者漏电等现象。
检查吸尘器的电源线是否有磨损或者断裂，若有问题应及时更换或者修理。
1.2 准备吸尘器配件：检查吸尘器配件是否齐全，如吸头、软管、滤网等。
确保配件的连接密切，无松动现象。
1.3 清理工作区域：在使用吸尘器之前，先将工作区域进行清理，清除大块的灰尘、杂物等，以免影响吸尘器的正常工作。
二、操作步骤2.1 开启吸尘器：将吸尘器插头插入电源插座，确保电源稳定。
然后按下吸尘器的开关，启动设备。
在启动吸尘器之前，确保吸头没有接触到任何物体。
2.2 吸尘器挪移方式：在操作吸尘器时，应保持身体平衡，双手握紧吸尘器的手柄。
以直线或者S型挪移方式进行吸尘，确保吸尘器能够覆盖到所有需要清洁的区域。
2.3 吸尘器使用时间：根据吸尘器的使用说明，合理控制吸尘器的使用时间，避免长期连续使用导致设备过热。
三、注意事项3.1 避免吸尘器过载：不要过度使用吸尘器，避免超过其额定功率。
在吸尘器工作时，尽量避免吸入大块的尘埃或者异物，以免阻塞吸尘器。
3.2 定期清理吸尘器配件：定期清理吸尘器配件，如吸头、滤网等。
如果滤网被阻塞，会影响吸尘器的吸力和清洁效果。
清洁时，应先断电并拔掉电源插头，然后用干净的布或者刷子清理配件。
3.3 避免湿润环境使用：吸尘器属于干式清洁设备，不适合在湿润的环境中使用。
在清洁湿润区域之前，应先将水分清除干净，以免损坏吸尘器。
四、存储和维护4.1 存储方式：在使用完吸尘器后，应将其存放在干燥、通风的地方，远离水源和高温环境。
可以使用专门的吸尘器收纳袋或者箱子，避免灰尘和杂物的侵入。
4.2 定期维护：定期对吸尘器进行维护保养，如清洁滤网、检查电源线是否有磨损等。
便携式吸尘器使用说明书部分 1：产品介绍便携式吸尘器是一种小巧轻便的家庭清洁工具，专为方便快捷清理室内灰尘和脏污而设计。
本使用说明书将详细介绍吸尘器的使用方法及注意事项，以确保您能够安全和高效地使用该产品。
部分 2：产品名称及规格- 产品名称：便携式吸尘器- 产品型号：XX-001- 重量：500克- 尺寸：20厘米 x 10厘米 x 5厘米- 电源：可充电锂电池- 电池容量：2000毫安时- 吸尘能力：3000帕斯卡- 附件：软管、刷头、充电器部分 3：安全注意事项为了您的安全和顺利使用，请在使用前务必阅读以下注意事项：1. 只能使用设备自带的充电器充电，切勿使用其他充电设备。
2. 操作时，请确保吸尘器和附件与水源、火源等远离，以防发生意外事故。
3. 请勿在潮湿的环境中使用吸尘器。
4. 切勿将吸尘器放置在高温、高压或阳光直射的地方，以防电池损坏或爆炸。
5. 在不使用吸尘器时，请关闭电源开关，并将电源适配器拔下。
部分 4：使用方法1. 充电：将充电器插头插入吸尘器的充电口，然后将充电器插头插入电源插座。
充电指示灯将亮起，表示正在充电。
当充电指示灯变为绿色时，说明充电完成。
2. 操作开关：按下吸尘器手柄上的电源开关，吸尘器将开始工作。
再次按下电源开关，吸尘器将停止工作。
3. 吸尘操作：将所需的附件连接到吸尘器的软管上，然后开始吸尘操作。
请确保附件牢固连接并正确使用，以获得最佳吸尘效果。
4. 清理过滤器：定期清理吸尘器过滤器可保持吸尘器的吸力。
请参考产品手册查看如何清洁过滤器。
5. 存放储存：当您使用完吸尘器后，请清理附件，并将吸尘器放置在干燥通风的地方储存，以延长其使用寿命。
部分 5：故障排除如果吸尘器遇到以下问题，请按照以下步骤进行排除：1. 无法充电：请确保充电插头正确连接并插入电源插座，检查电源是否正常工作。
2. 吸力不足：请检查过滤器是否需要清洁，并确保所有附件正确安装。
3. 无法启动：请检查电源开关是否打开且电量是否充足。
