au 错误代码表

报警码屏幕显示和含义1001INITIALIZE 提示仪器正在机械初始化1002WARMUP 提示温度和光学系统正在稳定1003STANDBY 提示仪器处于准备状态1004MEASURE START 提示仪器处于分析开始状态 MEASURE-11005NO MORE SAMPLE 提示正在吸取最后一个架子样本MEASURE-21006R1 DISPENSE FINISHED 提示所有的测试R1试剂分配完毕MEASURE-31007CUVETTE WASH AFTER MEASUREMENT START 提示样本分析完成，反应杯开始冲洗MEASURE-4 1008MEASURE END PROCESS 提示样本分析结束，反应杯冲洗结束STANDBY1009MEASURE END 提示样本分析结束，反应杯冲洗结束MEASURE模式的STANDBY1010MOVING TO STOP 提示进入停止状态，根据子报警具体分析可能的故障1011MOVING TO PAUSE 提示进入暂停状态，按START键可以继续操作1012PAUSE 提示目前为暂停状态1013STOP 提示目前为停止状态，一般是电脑或机械故障导致，排除故障后再启动1014SYSTEM END PROCESS 提示系统进程结束，处于关机状态1015W1 START 提示W1操作开始1016W1 END 提示W1操作结束1017W2 START 提示W2操作开始1018W2 END 提示W2操作结束1019PHOTOCAL START 光度校正开始1020PHOTOCAL END 光度校正结束1021ONE-TOUCH MODE ANALYSIS (aaaa) (Profile No. bb)1022REMOVE RACK FROM RACK FEEDER1030CHANGE INDEX1031ILLEGAL CONSTRUCTION (n)1051POWER ON2001THE SAME SAMPLE ID ALREADY REQUISITIONED (aaaa)样本编号已经申请（样本编号）2002NOT ALLOWED TO DELETE SAMPLE (aaaaa) 不能删除样本（样本编号）2003NOT ALLOWED TO DELETE REPEAT SAMPLE (aaaa) 不能删除重测样本（样本编号）2004ALREADY REQUISITIONED REPEAT SAMPLE (aaaa) 重测样本已经申请（样本编号）2005ALREADY MEASUREMENT STARTED (aaaaa) 标准品或试剂空白已经测量（样本编号）2006PRINTER NOT AVAILABLE 打印机不可用（忙）2007Part of data is not output yet 部分数据尚未输出。

分析上位完成，不能打印，或DPR STATUS--SYSTEM STATUS ICON--F4选择尚未打印的数据2008Ordering 不能切换模式，重新启动分析仪2091R1 LOT NO. DIFFERENT FROM RB (aa-bbbbb) c R1试剂空白的批号与试剂瓶的批号不同，重新执行新批号的试剂空白。

(位置号-测试名称)c：(None：血清；U:尿液；X：其它)2092R2 LOT NO. DIFFERENT FROM RB (aa-bbbbb) c R2试剂空白的批号与试剂瓶的批号不同，重新执行新批号的试剂空白。

2093R1 LOT NO. DIFFERENT FROM CAL (aa-bbbbb) c R1试剂校准的批号与试剂瓶的批号不同，重新执行新批号的校准。

2094R2 LOT NO. DIFFERENT FROM CAL (aa-bbbbb) c R2试剂校准的批号与试剂瓶的批号不同，重新执行新批号的校准。

2095R1 DIFFERENT LOT NO. (aaaaa) R1更换试剂后，所有试剂瓶批号都相同（测试名称）2096R2 DIFFERENT LOT NO. (aaaaa) R2更换试剂后，所有试剂瓶批号都相同（测试名称）2101REAGENT ID READ ERROR (aa) 试剂条码错误（1-76）。

错误码是1；过期数据；项目名称为？？？？。

检查条码和试剂放置。

2102REAGENT ID NOT DEFINED (aa) 试剂条码不准确（1-76）。

擦干净条码标签，正确放置试剂瓶。

2105ILLEGAL REAGENT POSITION (aa) 试剂位置不合法（1-76）。

试剂容量检查时发现条码标签与输入项目不符2106ILLEGAL BOTTLE SIZE (aa) 瓶规格不合法（1-76）。

2111NO REPLY FROM ANL (aa,bb) ANL无应答（信息，信息第一个字节）。

系统转为停止模式，重新启动系统。

2121ILLEGAL FLOPPY DISK 软盘不合法。

插入正确规格的软盘或重新插入。

2122NO DATA IN FLOPPY DISK 软盘内没有数据。

2123NO AREA IN FLOPPY DISK 写入失败，软盘容量不够。

2131ONLINE ERROR (aa) (bbbbbbbbb-ccccc-dd) 联机错误（错误类型）（出错文本-架编号-杯位置）2132ONLINE ERROR [aa] [bbbbbbbbb] 联机错误（错误类型）[出错文本]2133ONLINE FORMAT ERROR (aaaaaa-bbbbb-cc : NO SAMPLE No.) 联机格式错误（发送样本类型和样本标号-架编号-杯位置号）2134ONLINE FORMAT ERROR (aaaaaa-bbbbb-cc : NO SAMPLE ID) 联机格式错误（发送样本类型和样本标号-架编号-杯位置号）2135ONLINE ILLEGAL TEXT CODE (aaaaaa-bbbbb-cc : dd) 非法文本代码（发送样本类型和样本标号-架编号-杯位置号：接收到的文本）2136ONLINE ILLEGAL TEXT BLOCK No. (aaaaaa-bbbbb-cc : dd->ee) 非法文本块编号（发送样本类型和样本标号-架编号-杯位置号：先前接收的块识别码-最后接收的块识别码）2137ONLINE ILLEGAL SAMPLE No. (aaaaaa-bbbbb-cc : dddddd) 非法样本编号（发送样本类型和样本标号-架编号-杯位置号：接收到的样本类型和编号）2138ONLINE ILLEGAL RACK No. (aaaaaa-bbbbb-cc : ddddd-ee) 非法架编号（发送样本类型和样本标号-架编号-杯位置号：接收到架编号-杯位置号）2139ONLINE ILLEGAL SAMPLE KIND (aaaaaa-bbbbb-cc : dd) 非法样本种类（发送样本类型和样本标号-架编号-杯位置号：接收到样本种类）2140ONLINE ILLEGAL GENDER TEXT (aaaaaa-bbbbb-cc : d) 非法性别文本（发送样本类型和样本标号-架编号-杯位置号：接收到的性别）2141ONLINE ILLEGAL AGE/MONTH (aaaaaa-bbbbb-cc : ddd ee) 非法年龄（发送样本类型和样本标号-架编号-杯位置号：接收到的年龄）2142ONLINE ANALYSIS METHOD MISMATCH (aaaaaa-bbbbb-cc : dd <> ee) 分析方法不匹配（发送样本类型和样本标号-架编号-杯位置号：样本类型<>接收到的样本类型）2143ONLINE SAMPLE No. MISMATCH (aaaaaa-bbbbb-cc <> dddddd) 样本编号不匹配（发送样本类型和样本标号-架编号-杯位置号<>接收到的样本类型和编号）2144ONLINE RACK No. MISMATCH (aaaaaa : bbbbb-cc <> ddddd-ee) 架编号不匹配（发送样本类型和样本标号-架编号-杯位置号<>接收到的架编号-杯位置号）2145ONLINE MISMATCH (aaaaaa-bbbbb-cc : ddddddddd <> eeeeeeeee) 联机不匹配（发送样本类型和样本标号-架编号-杯位置号：发送的样本编号<>接收到的样本编号）2146ONLINE TEST ITEM ERROR (aaaaaa-bbbbb-cc) 联机测试项目错误（发送样本类型和样本标号-架编号-杯位置号）2147ONLINE REPEAT ITEM ERROR (aaaaaa-bbbbb-cc : dddddd) 联机重测项目错误（发送样本类型和样本标号-架编号-杯位置号：样本类型和原始编号）2151DTR SET ERROR DTR设置错误2152DSR CHECK TIMEOUT DSR检查超时2201ANL Communication Overrun First Time Error (aa,bb,c) ANL通讯首次超速错误（信息编号，错误编号，再试编号）2202ANL Communication Parity First Time Error (aa,bb,c) ANL通讯首次奇偶校验错误（信息编号，错误编号，再试编号）2203ANL Communication Framing First Time Error (aa,bb,c) ANL通讯首次框架错误（信息编号，错误编号，再试编号）2204ANL Communication other SIO First Time Error (aa,bb,c) ANL通讯首次其他SIO错误（信息编号，错误编号，再试编号）2205ANL Communication ENQ sent First Time Error (aa,bb,c) ANL通讯首次ENQ发送错误（信息编号，错误编号，再试编号）2206ANL Communication NAK Receive First Time Error (aa,bb,c) ANL通讯首次NAK接收错误（信息编号，错误编号，再试编号）2207ANL Communication Timeout First Time Error (aa,bb,c) ANL通讯首次超时错误（信息编号，错误编号，再试编号）2208ANL Communication Not Receive STX First Time Error (aa,bb,c) ANL通讯首次无STX接收错误（信息编号，错误编号，再试编号）2209ANL Communication Receive Text length not equal First Time Error (aa,bb,c) ANL通讯首次接收文本超长错误（信息编号，错误编号，再试编号）2210ANL Communication Receive Illegal ETX Location First Time Error (aa,bb,c) ANL通讯首次ETX位置不合法（信息编号，错误编号，再试编号）2211ANL Communication BCC First Time Error (aa,bb,c) BCC首次错误（信息编号，错误编号，再试编号）2212ANL Communication Text Code First Time Error (aa,bb,c) 文本码首次错误（信息编号，错误编号，再试编号）2213ANL Communication Text Sending Char Receive First Time Error (aa,bb,c) 文本发送字符接收首次错误（信息编号，错误编号，再试编号）2214ANL Communication Overrun Error (aa,bb,c) 超速错误（信息编号，错误编号，再试编号）2215ANL Communication Parity Error (aa,bb,c) 奇偶错误（信息编号，错误编号，再试编号）2216ANL Communication Framing Error (aa,bb,c) 框架错误（信息编号，错误编号，再试编号）2217ANL Communication other SIO Error (aa,bb,c) 其他SIO（信息编号，错误编号，再试编号）2218ANL Communication ENQ send Error (aa,bb,c) ENQ发送（信息编号，错误编号，再试编号）2219ANL Communication NAK Receive (aa,bb,c) NAK接收（信息编号，错误编号，再试编号）2220ANL Communication Timeout Error (aa,bb,c) 超时（信息编号，错误编号，再试编号）2221ANL Communication Not Receive STX (aa,bb,c) 无接收STX（信息编号，错误编号，再试编号）2222ANL Communication Receive Text length not equal (aa,bb,c) 接收文本长度不相等（信息编号，错误编号，再试编号）2223ANL Communication Receive Illegal ETX Location (aa,bb,c) 接收ETX位置不合法（信息编号，错误编号，再试编号）2224ANL Communication BCC Error (aa,bb,c) BCC错误（信息编号，错误编号，再试编号）2225ANL Communication Text Code Error (aa,bb,c) 文本码错误（信息编号，错误编号，再试编号）2226ANL Communication Text Sending Char Receive Error (aa,bb,c) 文本发送字符接收错误（信息编号，错误编号，再试编号）2251PRINTER NOT SELECTED 打印机没有选择2301NO FLOPPY DISK 无软盘2302FLOPPY DISK READ/WRITE ERROR 软盘读写错误3103POWER FAILURE DETECTED 探测到电源失败3104PHOTOMETER CPU INITIAL ERROR (aa) 光度计CPU初始化错误（详细错误）HEX 0位：ROM校验错误，1位：SRAM 不能读写数据；2位：错误发生在ARCHNET；3位：OPMC错误3105COM. CONTROL CPU INITIAL ERROR (aa) 通讯控制CPU初始化错误（HEX）3106OPTICAL COM. MASTER INITIAL ERROR (aa,bb,cc) 光纤主站错误是错误（HEX详细错误，主站错误位置，主站错误状态）3107OPTICAL COM. SLAVE INITIAL ERROR (aa) 光纤从站错误是错误（HEX详细错误）3108PHOTOMETER CPU -> ANL COM. ERROR (aa,bb,cc,dd) 光度计CPU到ANL通讯错误3109PHOTOMETER CPU -> ANL TEXT NOT RECEIVED (aa,bb,cc,dd) 光度计CPU到ANL通讯无接收文本3110ANL -> PHOTOMETER CPU COM. ERROR (aa,bb,cc,dd) ANL到光度计通讯错误3111PHOTOMETER CPU ERROR (aa,b) 光度计CPU错误3112OPTICAL COM. ERROR (aa,bb,cc,dd) 光纤通讯错误3113OPMC ERROR (aa,bb,cc) 光纤连接器错误3114ANL -> COM. CONTROL CPU I/F ERROR (aa) ANL-光纤通讯控制CPU错误3115ANL -> BAR CODE READER COM. ERROR (aa,bb) ANL-条码阅读器通讯错误3116ANL <- BAR CODE READER COM. ERROR (aa,bb) ANL-条码阅读器通讯错误3118ANL <- DPR COM. ERROR-1 (aa,bb) ANL-DPR通讯错误3119ANL <- DPR TEXT NOT RECEIVED (aa) ANL-DPR无接收文本3121ANL -> DPR COM. ERROR (aa,bb) ANL-DPR通讯错误3122RACK/SAMPLE ID READ ERROR (aa) 架/样本条码读取错误（1位：字符检查错误；2位：条码位数错误）3123STAT SAMPLE ID READ ERROR (aa) 急诊样本条码读取错误（0：规定时间内读取没有完成；1：字符检查错误；2：条码位数错误）3124RACK ID READ ERROR (aa,bb) 架条码错误3127REAGENT ID READ ERROR (aa) 试剂条码错误3129ORIGINAL DETERGENT B EMPTY 浓缩清洗剂B空3130ORIGINAL DETERGENT A EMPTY 浓缩清洗剂A空3131DETERGENT B SHORT 清洗剂B缺少3132DETERGENT A SHORT 清洗剂A缺少3133DI WATER SHORT 去离子水缺少3134DI WATER EMPTY 去离子水空3135DETERGENT B OVERFLOW 清洗剂B溢出3136DETERGENT A OVERFLOW 清洗剂A溢出3137DI WATER OVERFLOW 去离子水溢出3138REAGENT REF. COVER OPEN 试剂仓盖打开3140INCUBATION. BATH/REAGENT REF. TMP. A/D ERROR 反应盘/试剂仓温度A/D转换错误3141LAMP OFF 灯泡关闭3142LAMP DARK 灯泡太暗3143PHOTOMETER DATA ERROR (aa) 光度计数据错误3144NO VACUUM PRESSURE 无负压3145VACUUM TANK FULL 负压罐满3146RACK DETECTED ON FEEDER BELT (aa) 步进皮带上有架子3147RACK DETECTED ON RERUN FEEDER BELT (aa) 重测步进皮带上有架子3149RACK RECEIVER FULL 架满3150NO RACK 无架3151NO STAT CUP 无急诊杯3152NO SAMPLE PROBE DETERGENT (aa) 无样本针清洗剂3153REAGENT PROBE DETERGENT SHORT 试剂针清洗剂太少3155RACK CLASS ERROR 架类型错误3157SAMPLE INFORMATION UNMATCH (aa,bbbb,cc,dd,eeeee) 样本信息不匹配3160ACAL INCOMPLETE ACAL未完成3161QC INCOMPLETE 质控不完整3162RB/ACAL SAMPLE PROHIBITED 人工急诊试剂空白/ACAL中断3163AUTOMATIC REPEAT ILLEGAL RACK No. (aa,bbbbbbb) 自动重测架号不合法3164AUTOMATIC REPEAT RACK OVER 自动重测架结束3165SAMPLING POSITION, RACK STEP DISABLED T (aa) 吸样位置，架步进无效3166RACK SUPPLIER ERROR T (aa,bb,cc) 架进给错误3167RACK BUFFER ERROR T (aa,bb,cc) 架缓冲错误3168CPU DETECTION POSITION, RACK STEP UNIT ERROR T (aa,bb,cc) CPU监测位置、架步进单元错误3169SAMPLING POSITION, RACK STEP UNIT ERROR T (aa,bb,cc) 吸样位置，架步进单元错误3171SAMPLING POSITION, RACK JAM T (aa) 吸样位置，架卡住3172RACK BUFFER JAM T 架缓冲卡住3173RACK RECEIVER JAM T 架接收卡住3174RACK RECEIVER UNIT ERROR T (aa,bb,cc) 架接收单元错误3175STAT TABLE ERROR T (aa,bb,cc) 急诊盘错误3176SAMPLE PROBE UP/DOWN ERROR T (aa,bb,cc) 样本针上下错误3177SAMPLE PROBE ROTATION ERROR T (aa,bb,cc) 样本针摆动错误3178SAMPLE DISPENSER ERROR T (aa,bb,cc) 样本分配错误3179SAMPLE PROBE LEVEL DETECTOR ERROR T (aa) 样本针液面监测错误3180SAMPLE PROBE INTERNAL WASH DISABLED T (aa,bb,cc) 样本针内壁冲洗无效3181REAGENT PROBE UP/DOWN ERROR T (aa,bb,cc) 试剂针上下错误3182REAGENT PROBE ROTATION ERROR T (aa,bb,cc) 试剂针摆动错误3183REAGENT REF. ROTATION ERROR T (aa,bb,cc)3184REAGENT DISPENSER ERROR T (aa,bb,cc) 试剂分配错误3185REAGENT PROBE LEVEL DETECTOR ERROR T (aa) 试剂针液面监测错误3187REAGENT PROBE INTERNAL WASH DISABLED T (aa,bb,cc) 试剂针内壁冲洗无效3195MIX UP/DOWN ERROR T (aa,bb,cc) 搅拌器上下错误3196MIX ROTATION ERROR T (aa,bb,cc) 搅拌器旋转错误3197MIXING ERROR T 搅拌器错误3201CUVETTE WASH UNIT ERROR T (aa,bb,cc) 冲洗站单元错误3202CUVETTE WASH DISABLED T (aa,bb,cc) 冲洗站无效3203CUVETTE WHEEL ROTATION ERROR T (aa,bb,cc) 反应盘旋转错误3204PHOTOMETER ERROR T (aa) 光度计错误3206LBF RACK EXIST $T3212STRONG DRAIN TANK FULL 浓废液罐满3213WEAK DRAIN TANK FULL 淡废液罐满3214R1 REAGENT SHORT (aaaaa,bb) R1缺少3215R2 REAGENT SHORT (aaaaa,bb) R2缺少3216R1 REAGENT EMPTY (aaaaaaaaaa,bbbbb,cc,dd) R1空3217R2 REAGENT EMPTY (aaaaaaaaaa,bbbbb,cc,dd) R2空3218INCUBATION BATH TEMP. ERROR 反应水槽温度错误3220SAMPLE EMPTY LEVEL DETECT (aaaaaa,bb,cc,ddddd-ee) 样品空3222AUTOMATIC REPEAT BELT FEEDER JAM 自动重测皮带步进卡住3232AUTOMATIC REPEAT RECEIVER JAM 自动重测接收卡住3237SAMPLE PROBE STUFF SENSOR ERROR T (aa) 样本针堵塞传感器错误3238STUFF SAMPLE DETECT (aaaaa,bb,ccccc-dd) 样本探测堵塞3253DETERGENT A EMPTY 清洗剂A空3254DETERGENT B EMPTY 清洗剂B空3255ISE COVER OPEN ISE盖打开3256STAT COVER OPEN 急诊盖打开3257STAT SET OVER TIME 急诊设置超时3258AUTO REPEAT RUN RACK DISABLED 自动重测运行架无效3259MIRROR ROTATION ERROR T (aa,bb,cc) 棱镜旋转错误3260R2 REAGENT EMPTY (aaaaa,bb,cc) R2试剂空3261PRE DILUTION WATER SHORT 预稀释水少3262PRE DILUTION WATER EMPTY LEVEL DETECT (aaaaaa,bb,cc) 预稀释水空3264REAGENT TRANSPOSITION DISABLED (aa) 试剂转位无效3266QC SAMPLE PROHIBITED 质控样本阻止3267MEASURE RESTART DISABLE 测量重新开始无效3268REG. PROBE DETERGENT SHORT T (CLN-a,bb) 试剂针清洗剂少3269REG. PROBE DETERGENT EMPTY T (CNL-a,bb) 试剂针清洗剂空3301NO ISE 无ISE3302ISE INITIAL ERROR (aa) ISE初始化错误3303ISE MID STANDARD SHORT ISE内标液少3304ISE BUFFER SHORT ISE缓冲液少3305ISE REFERENCE SHORT ISE参比液少3306ISE CLEANING SOLUTION SHORT ISE清洗剂少3307ISE STANDARD L SHORT ISE低准液少3308ISE STANDARD H SHORT ISE高标液少3309ISE SELECTIVITY CHECK (Na) SHORT ISE选择性检查Na少3310ISE SELECTIVITY CHECK (K) SHORT ISE选择性检查K少3311ISE LOW DATA ISE数据低3313ISE SAMPLE No. ILLEGAL PROCEDURE (aaaa) ISE编号程序不合法3314ANL <- ISE COM. ERROR (aa,bb) ANL-ISE通讯错误3315ANL <- ISE TEXT NOT RECEIVED (aa,bb) ANL-ISE无接收文本3316ANL <- ISE COM. RECEPTION ERROR (aa,bb) ANL-ISE通讯接收错误3351ISE <- ANL COM. ERROR (aa,bb) ISE-ANL通讯错误3352ISE <- ANL TEXT NOT RECEIVED (aa,bb) ISE-ANL无接收文本3353ISE SEQUENCE ERROR T ISE顺序错误3354ISE SYNC SIGNAL ERROR T (aa,bb,cc,dd,ee,ff,gg) ISE同步信号错误3355ISE A/D ERROR T (aa) ISE A/D转换错误3356ISE TEMP. ERROR (aa) ISE温度错误3357ISE BUFFER DISPENSER ERROR T (aa) ISE缓冲液分配错误3358ISE MID STANDARD PUMP ERROR T (aa) ISE内标液泵错误3359ISE SAMPLE ASPIRATION PUMP ERROR T (aa) ISE样本吸取泵错误3360ISE SAMPLE MIXER ERROR T (aa) ISE样本混合错误3361ISE D-POT OVERFLOW SENSOR ERROR T (aa) ISE样本池溢流传感器错误3362ISE -> ANL COM. RECEPTION ERROR (aa,bb) ISE-ANL通讯接收错误4001NO SAMPLE CUP (aaaaa-bbbbb-cc) 无样本杯4002SAMPLE NOP (aaaaa-bbbbb-cc) 样本无操作4003SAMPLE ID NOT FOUND (aaaaa,bbbbb,cc) 样本编号没有找到4004REPEAT SAMPLE ID NOT FOUND (aaaaa-bbbbb-cc) 重测样本编号没有找到4005REPEAT SAMPLE NOP (aaaaa-bbbbb-cc) 重测样本没有操作请求4006ILLEGAL SAMPLE ID (aaaaa-bbbbb) 样本编号非法4008BROKEN LABEL (aaaaa-bbbbb-cc) 中断列表4009REPEAT BROKEN LABEL (aaaaa-bbbbb-cc) 重测列表中断4010SAMPLE ID READ ERROR (aaaaa-bbbbb-cc) 样本编号读取错误4011REPEAT SAMPLE ID READ ERROR (aaaaa-bbbbb-cc) 重测样本编号读取错误4012MEASURE COMPLETED FOR THE READ SAMPLE ID (aaaaa-bbbbb-cc) 读取的样本编号测试完成4013CALIBRATION FACTOR RANGE OVER (aaaaa) c 定标因数超过范围4014CALIBRATION FACTOR RANGE UNDER (aaaaa) c 定标因数低于范围4015CALIBRATION OD RANGE OVER (aaaaa) b,c 定标OD超过范围4016CALIBRATION OD RANGE UNDER (aaaaa) b,c 定标OD低于范围4017CALIBRATION ERROR (aaaaa) c 定标错误4018QC DATA RANGE OVER (aaaaa,bb,ccccc,d) 质控数据超过范围4019QC DATA RANGE UNDER (aaaaa,bb,ccccc,d) 质控数据低于范围4020QC DATA CHECK ERROR (aaaaa,bb,ccccc,d) 质控数据检查错误4021PANIC VALUE (aaaaa,bbbbb,cc,dd) 危机值4023PHOTOCAL DATA ERROR 光度校正数据错误4024REAGENT REF. TEMPERATURE LOW 试剂温度低4025REAGENT REF. TEMPERATURE HIGH 试剂温度高4026INCUBATION BATH TEMPERATURE HIGH 反应槽温度高4027INCUBATION BATH TEMPERATURE LOW 反应槽温度低4028STAT SAMPLE MEASURE START CANCELED 开始急诊样本测量取消4029DPR <-> ANL COM. START TIMEOUT DPR-ANL通讯开始超时4030DPR <-> ANL COM. TIMEOUT (aa) DPR-Anl通讯超时4031ILLEGAL PARAMETER (aaaaa,b,c,d,e) 项目非法4035NO SAMPLE REQUISITION (aaaaa) 无样本申请4036DATA WRITE DISABLED (aaaaa) 写数据无效4040SAMPLE BLANK CORRECTION WITHOUT COLOR DATA (aaaaa-bbbbb-cc ddddd eeeee) 样本空白校正不使用颜色数据4041SAMPLE BLANK CORRECTION WITHOUT BLANK DATA (aaaaa-bbbbb-cc ddddd eeeee) 样本空白校正不使用空白数据4042STAT SAMPLE MEASURE START ERROR 急诊样本测量开始错误4051REPEAT SAMPLE NO CUP (aaaaa-bbbbb-cc) 重测样本无杯子4052ILLEGAL REPEAT SAMPLE ID (aaaaa) 重测样本编号非法4053MAXIMUM NUMBER OF SAMPLE (aa) 样本号码最大4101NO STAT CUP (CALIBRATION NO. aa bb) 无急诊杯4102NO STAT CUP (CONTROL NO. aa bb) 无急诊杯4103STAT CAL/QC DUPLICATE ID (aaaaa) bb 急诊、质控、标准品一样的编号4104STAT CAL/QC ID READ ERROR (aa) 急诊、质控、标准品编号读取错误4105NO STAT CUP (RB) 无急诊杯4106INVALID STAT CUP (CALIBRATION NO. aa) 急诊杯无效4107INVALID STAT CUP (CONTROL NO. aa) 急诊杯无效4108INVALID STAT CUP (RB) 急诊杯无效9001LOGIN [aa] 登录9002LOGOUT [aa] 注销9003TEMPORARY LOGIN [aa] 临时登录9004MENU [aa] 菜单9005MENU [aa] EXIT 菜单 退出9141Hard Copy Error 硬盘复制9143PRINTER BUSY 打印机忙9173SECONDARY PRINTER BUSY 备用打印机忙9174PRINTOUT ERROR 打印输出错误9176SECONDARY PRINTER PRINTOUT ERROR 备用打印输出错误9231PASSWORD ERROR [aa] 密码错误9232NEW PASSWORD IS NOT IDENTICAL WITH CONFIRMATION PASSWORD 新密码校验密码不一致9241PRINTER BUSY 打印机忙9291Database Inf [aa]9292Database Error [aa] 数据库错误9401Access is denied 接入拒绝9402This account is currently disabled and cannot be logged on to 当前账号无效，不能登录9403The user’s account has expired 用户账号过期9404Some user account restriction has prevented successful authentication 用户账号限制相同9405Attempt to create file that already exists 尝试创建的文件已经存在9406The system is currently running with the last-known-good configuration 当前系统运行前一次正常启动的9407The storage control blocks were destroyed 存储控制失败9408The specified user name is invalid 指定用户名称无效9409The configuration registry database is damaged 配置登记数据库损坏9410The configuration registry key is invalid 配置登记索引无效9411The requested resource is in use 请求资源使用中9412Cannot complete function for some reason 同样的理由不能完成9413The directory or file cannot be created 不能创建文件或文件夹9414The configuration registry key cannot be opened 配置登记索引不能打开9415The configuration registry key cannot be read 配置登记索引不能读取9416The configuration registry key cannot be written 配置登记索引不能写入9147An attempt was made to create a stable subkey under a volatile parent key 尝试建立子索引9418Data error 数据错误9419The database specified dose not exist 指定数据库不存在9420The directory is not empty 文件夹不空9421The directory name is invalid 文件夹名称无效9422The disk structure is damaged and nonreadable 磁盘结构损坏不能读取9423There is not enough space on the disk 磁盘空间不足9424While accessing the hard disk, a disk operation failed 访问硬盘时，操作失败9425While accessing the hard disk, a recalibrate operation failed 访问硬盘时，重定标操作失败9426 A hard disk controller reset was needed, but even that failed 硬盘控制器必须复位，偶校验失败9427An extended error has occurred 发生扩展错误9428The file or directory is damaged and nonreadable 文件或文件夹错误不能读取9429The system cannot find the file specified 系统不能找到指定文件9430The file name or extension is too long 文件名或扩展名太长9431The disk is full 磁盘满9432Reached End Of File 文件到头9433This operation cannot be completed due to on-disk data structure corruption 操作不能完成，因为在盘数据损坏9434The system cannot find the specified drive 系统不能找到指定的驱动器9435The flag passed is incorrect 标志通过错误9436The flags are invalid 标志失败9437The user account has time restrictions and cannot be logged onto at now 用户账号时间限制，不能现在9438The parameter is incorrect 参数不正确9439The specified network password is incorrect 指定网络密码不正确9440The format of the specified password is invalid 指定密码格式错误9441The printer command is invalid 打印命令不正确9442The printer name is invalid 打印机名不正确9443The user account is restricted and cannot be used to log on 用户账号限制，不能登录9444The attempted logon is invalid 尝试登录失败9445The global filename characters * or ? are entered incorrectly 文件名存在*或？符号，输入不正确9446An attempt was made to move the file pointer before the beginning of the file 文件头尝试移动文件头9447System could not allocate required space in a registry log 系统不能分配登记日记空间9448The drive is not ready 驱动器没有准备好9449The system cannot open the specified device or file 系统不能打开指定文件或设备9450The I/O operation was aborted due to either thread exit or application request I/O操作失败，只能关闭进程或申请9451The printer is out of paper 打印机却纸9452File waiting to be printed was deleted 删除等待打印文件9453The printer queue is full 打印队列满9454The registry is damaged 档案损坏9455The registry initiated an I/O operation that had an unrecoverable failure I/O登记不可预料失败9456The drive cannot locate a specific area on the disk 磁盘不能驱动指定的扇区9457The file pointer cannot be set on the specified device or file 文件点不能设置指定的设备或文件9458Insert the disk for drive 1 在驱动器1插入磁盘9459The credentials supplied conflict with an existing set of credentials 资格冲突9460The process cannot access the file because it is being used by another 文件处理失败，另一个程序正在9461The system cannot open the file 系统不能打开文件9462The disk media is not recognized. It may not be formatted 系统媒体不能确认，没有格式化9463The media is write protected 写保护9471File genric Error [%s] 文件错误9472File not found [%s] 文件没有找到9473Bad pathname [%s] 路径名不正确9474Too many open files [%s] 打开文件太大9475File access denied [%s] 文件决绝读取9476Invalid File handle [%s] 文件句柄无效9477Can’t remove current directory [%s] 不能移动当前目录9478Full directory [%s] 目录满9479Bad seek pointer [%s] 搜寻指针失败9480File Hardware I/O Error [%s] 文件硬件I/O错误9481File sharing violation [%s] 文件共享失败9482File lock violation [%s] 文件锁失败9483File disk full [%s] 文件盘满9484File end of file [%s] 文件结束。