工厂专业英语术语Assem bly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Pneumatic screw driver气动起子worktable 工作桌O OBA开箱检查fit together组装在一起fasten锁紧(螺丝) fixture 夹具(治具) pallet栈板barcode条码barcode scanner条码扫描器fuse together熔合fuse m achine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cos metic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs. inch 镑、英寸EMI gasket导电条front plate前板rear plate后板chassis 基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS 电源电压接拉键sheet m etal parts 冲件plastic parts塑胶件SOP制造作业程序material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线left fork叉车personnel resource depart m en t 人力资源部production depart ment生产部门planning depart m ent企划部QC Secti on品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common e quipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic m achine油压机lathe车床planer |'plein?|刨床miller铣床grinder磨床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting m achine铆合机position职务president董事长general manager总经理special assistant m anager特助factory director厂长depart m ent director部长deputy m anager | =vice m anager副理section supervisor课长deputy section supervisor =vice section superisor副课长group leader/supervisor组长line supervisor线长assistant m anager助理to m ove, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect m aterial接料to reverse m aterial 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load m aterial上料to unload m aterial卸料to return m aterial/stock to退料scraped |'skr?pid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient m anufacturing procedure制程不良oxidation |' ksi'dei?n|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良em bedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车com pound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓administration/general affairs dept总务部autom atic screwdriver电动启子thicknes s gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单location地点present m embers出席人员subject主题conclusion结论decision item s决议事项responsible depart m ent负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheet PCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准depart ment部门stock age analysis sheet 库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete m aterial良品已呆滞to be inspected or reworked 待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet 年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw m aterials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list 备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flam e cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die butto n圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopp er清角active plate活动板baffle plate挡块cover plate盖板m ale die公模fem ale die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetizat ion去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜 D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products 报放心品defective products不良品finished products成品disposed products处理品barcode 条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer 备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting m achine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction =interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕?? shine 亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grai n细粒grit m aker抽粒机cushion缓冲magnalium镁铝合金m agnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tem po生产进度现状torque扭矩spline=t he multiple keys花键quenchi ng淬火tem pering回火annealing退火carbonization碳化tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机。
公司英語-----教育訓練部一:常用術語Hon Hai 鴻海CMM Component module move 機動元件整合CEM Contract Manufaction service 合約委托代工IBSC Internet Business Solution Center 國際互聯網應用中心PCEG Personal Computer Enclosure group個人電腦外設事業群（FOXTEQ）CCBG Connector&cable business groupCPBG Competition business groupESBG Enterprise system business group 鴻富錦事業群SABG system assembly business group 系統組裝事業群NWE Net Work EnclosureNSE Network system enclosureNSG Network system groupNFE Network flexible enclosureFoxcavity = HZ = Hong Zhun 鴻準Stamping tool shop I 沖模一廠Stamping tool shop II 沖模二廠Prototype workshop 樣品中心Steel factory 裁剪廠PCE molding tooling workshop PCE塑模廠Hua Nan test and measurement center 華南檢測中心MPE mobile phone enclosure MPEMBE mobile phone and notebook enclosure 明塑厂MGE Alloy magnesium alloy enclosure 鎂合金Engineer standard 工標Document center (database center)資料中心Design Center 設計中心Painting烤漆(廠) Assembly組裝(廠) Stamping沖壓(廠) Education and Training教育訓練proposal improvement/creative suggestion提案改善Technological exchange and study 技術交流研習會Technology and Development Committee 技術發展委員會BS Brain Storming腦力激蕩QCC Quality Control Circle品質圈PDCA Plan Do Check Action計劃執行檢查總結DCC delivery control center 交貨管制中心3CComputer 電腦類產品Consumer electronics 消費性電子產品Communication 通訊類產品Core value（核心价值）Love 愛心Confidence 信心Decision 決心Corporate culture(公司文化)Integration 融合Responsibility 責任Progress 進步3T STRATEGYTime to market 及時切入生產Time to volume 及時大量生產Time to money 及時大量交貨FOUR CONTROL SYSTEM 四大管制系統Engineering control system 工程管制系統Quality control system品質管制系統Manufacturing control system生產管制系統Management control system經營管制系統7SClassification整理(sorting, organization)-seiriRegulation整頓(arrangement, tidiness)-seitonCleanliness清掃(sweeping, purity)-seisoConservation清洁(cleaning, cleanliness)-seiktsuCulture教養(discipline)-shitsukeSave 節約Safety安全二:英文縮寫品質人員名稱類QC quality control品質管理人員FQC final quality control終點品質管制人員IPQC in process quality control制程中的品質管制人員OQC output quality control最終出貨品質管制人員IQC incoming quality control進料品質管制人員TQC total quality control全面質量管理PQC passage quality control段檢人員QA quality assurance質量保證人員OQA output quality assurance出貨質量保證人員QE quality engineering品質工程人員品質保證類FAI first article inspection新品首件檢查FAA first article assurance首件確認CP capability index能力指數CPK capability process index模具製程能力參數SSQA standardized supplier quality audit合格供應商品質評估FMEA failure model effectiveness analysis失效模式分析FQC運作類AQL Acceptable Quality Level運作類允收品質水準S/S Sample size抽樣檢驗樣本大小ACC Accept允收REE Reject拒收CR Critical極嚴重的MAJ Major主要的MIN Minor輕微的Q/R/S Quality/Reliability/Service品質/可靠度/服務P/N Part Number料號L/N Lot Number批號AOD Accept On Deviation特采UAI Use As It特采FPIR First Piece Inspection Report 首件檢查報告PPM Percent Per Million百萬分之一制程統計品管專類SPC Statistical Process Control統計製程管制SQC Statistical Quality Control統計品質管制GRR Gauge Reproducibility & Repeatability量具之再制性及重測性判斷量可靠與否DIM Dimension尺寸DIA Diameter直徑N Number樣品數其它品質術語類QIT Quality Improvement Team品質改善組ZD Zero Defect零缺點QI Quality Improvement品質改善QP Quality Policy品质方針TQM Total Quality Management全面品質管理RMA Return Material Audit退料認可7QCTools7 Quality Control Tools品管七大手法通用之件類ECN Engineering Change Notice工程變更通知(供應商) ECO Engineering Change Order工程改動要求(客戶) PCN Process Change Notice工序改動通知PMP Product Management Plan生產管制計劃SIP Standard Inspection Procedure製程檢驗標準程序SOP Standard Operation Procedure製造作業規範IS Inspection Specification成品檢驗規範BOM Bill Of Material物料清單PS Package Specification包裝規範SPEC Specification規格DWG Drawing圖面系統文件類ES Engineering Standard工程標準CGOO China General PCE龍華廠文件IWS International Workman Standard工藝標準ISO International Standard Organization國際標準化組織GS General Specification一般規格部類PMC Production & Material Control生產和物料控制PCC Product control center 生產管制中心PPC Production Plan Control生產計劃控制MC Material Control物料控制DC Document Center資料中心QE Quality Engineering品質工程(部)QA Quality Assurance品質保證(處)QC Quality Control品質管制(課)PD Product Department生產部LAB Laboratory實驗室IE Industrial Engineering工業工程R&D Research & Design設計開發部生產類PCs Pieces個(根,塊等)PRS Pairs雙(對等)CTN Carton卡通箱PAL Pallet/skid棧板PO Purchasing Order采購訂單MO Manufacture Order生產單D/C Date Code生產日期碼ID/C Identification Code(供應商)識別碼SWR Special Work Request特殊工作需求L/N Lot Number批號P/N Part Number料號OEM Original Equipment Manufacture原設備製造PC Personal Computer個人電腦CPU Central Processing Unit中央處理器A.S.A.P As Soon As Possible盡可能快的E-MAIL Electrical-Mail電子郵件N/A Not Applicable不適用QTY Quantity數量I/O input/output輸入/輸出Not Good不行,不合格C=0Critical=0極嚴重不允許APP Approve核準,認可,承認CHK Check確認ASS'Y Assembly裝配,組裝T/P True Position真位度5WIH When, Where, Who, What, Why, How to6M Man, Machine, Material, Method, Measurement, Message4MTH Man, Material, Money, Method, Time, How人力,物力,財務,技術,時間(資源) SQA Strategy Quality Assurance策略品質保證DQA Design Quality Assurance設計品質保證MQA Manufacture Quality Assurance製造品質保證SSQA Sales and service Quality Assurance銷售及服務品質保證LRR Lot Reject Rate批退率SPS Switching power supply電源箱DT Desk Top臥式(機箱)MT Mini-Tower立式(機箱)DVD Digital Video DiskVCD Video Compact DiskLCD Liquid Crystal DisplayCAD Computer Aided DesignCAM Computer Aided ManufacturingCAE Computer Aided EngineeringPCB Printed Circuit Board印刷電路板CAR Correction Action Report改善報告NG Not Good不良WDR Weekly Delivery Requirement周出貨要求PPM Percent Per Million百萬分之一TPM Total Production Maintenance全面生產保養MRP Material Requirement Planning物料需計劃OS Operation System作業系統TBA To Be Assured待定,定缺D/C Drawing ChangeP/P Plans & ProcedureEMI Electrical-Music Industry電子音樂工業Electrical Magnetic Interference 電子干扰RFI Read Frequency Input讀頻輸入MMC Maximum Material ConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material SizeLED lighting-emitting diode 發光二极管QBR Quarter Business RecordCIP Continuous improvement processFGI Forecasted Goal InventoryCNC Computerized numeral controllerB2C Business to customerB2B Business to businessAVL Approved vendor listPOP Procedure of packagingEOL End of lifeVDCS Vender defect correcting sheetPDCS Process defect correcting sheetGRN Goods receiving noteA/R Accounting receivableA/P Accounting payable三:專業詞匯通用類president董事長operator作業員position職務general manager總經理special assistant 特deputy manager |'depjuti| =vice manager副理deputy supervisor =vice supervisor副課group leader組長line leader線長supervisor 課長responsible department負責單Human Resources Department人力資源部Head count 人頭數production department生產部planning department企劃部QC Section品管課stamping factory沖壓廠painting factory烤漆廠molding factory成型廠administration/general affairs dept./總務部production unit生產單位meeting minutes會議記錄distribution department分發單subject主題conclusion結論decision items決議事項pre-fixed finishing date預定完成Color management 顏色管理Visual management 目視管理production capacity生產力first count初盤first check初盤復櫂second count 復盤second check復盤復核quantity of physical inventory second count 復盤點數量physical inventory盤點數量physical count quantity帳面數difference quantity差異量spare parts physical inventory list備品盤點清單cause analysis原因分析waste materials廢料description品名specification 規格model機種work order工单revision版次remark備注registration登記registration card登記卡to control管制application form for purchase請購consume, consumption消耗to notify通知to fill in填寫to collect, to gather收集statistics統計cosmetic inspection standard 外觀檢驗規範computer case 電腦外殼(組件)personal computer enclosure 電腦機箱產品front plate前板rear plate后板chassis |'∫æsi| 基座bezel panel面板Hood 上蓋base pan 基座bezel 面板riser card 擴充卡flat cable 排線TOP driver cage 上磁架bottom driver cage 下磁架resin film 樹脂膜raw materials原料materials物料steel plate鋼板roll/coil material捲料spare parts =buffer備品plastic parts塑膠件sheet metal parts/stamping parts 沖件material check list物料檢查表finished product成品semi-finished product半成品good product/accepted goods/ acceptedparts/good parts良品defective product/non-good parts不良品disposed goods處理品warehouse/hub倉庫packing material包材basket蝴蝶竺plastic basket膠筐flow chart流程表單production tempo生產進度現lots of production生產批量manufacture procedure制程to revise, modify修訂to switch over to, switch—to,switching over切換engineering bottleneck, projectdifficulty工程瓶glove(s)手套glove(s) with exposed fingers割手Band-Aid創可貼Industrial alcohol工業酒精broom掃把mop拖把vacuum cleaner吸塵器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋liaison聯絡單rags抹布lamp holder燈架to mop the floor拖地to clean a table擦桌子air pipe 氣管delivery deadline交貨期die worker模工production, to produce生產equipment設備resistance電阻beacon警示燈coolant冷卻液crusher破碎機club car高爾夫球車plate電鍍power button電源按鍵reset button重置鍵forklift叉車Workshop traveler 天車trailer =long vehicle拖板車Hydraulic trolley手壓車hydraulic hand jack油壓板車casing = containerization裝箱velocity速度patent專利coordinate座標supply and demand供求career card履歷卡barricade隔板carton box紙箱to pull and stretch拉伸work cell/work shop工作間sub-line支線bottleneck 瓶頸模具工程類plain die簡易模pierce die沖孔模forming die成型模progressive die連續模stage die工程模compound die復合模shearing die剪邊模riveting die鉚合模feature die公母模male die公模female die母模cavity型控母模core模心公模die change 換模to fix a die裝模to repair a die修模punch set上模座punch pad上墊板punch holder上夾板stripper pad脫料背板up stripper上脫料板upper plate上模板lower plate下模板die pad下墊板die holder下夾板die set下模座bottom block下墊腳bottom plate下托板(底板)upper supporting blank上承板upper padding plate blank上墊top plate上托板（頂板）top block上墊腳stripping plate內外打(脫料板) outer stripper外脫料板inner stripper內脫料板lower stripper下脫料板punch沖頭insert入塊(嵌入件)deburring punch壓毛邊沖子groove punch壓線沖子stamped punch字模沖子round punch圓沖子special shape punch異形沖子bending block折刀roller滾軸baffle plate擋塊located block定位塊supporting block for location定位支承塊air cushion plate氣墊板air-cushion eject-rod氣墊頂桿trimming punch切邊沖子stiffening rib punch = stinger 加強筋衝子ribbon punch壓筋沖子reel-stretch punch卷圓壓平沖guide plate定位板sliding block滑塊sliding dowel block滑塊固定die locker鎖模器pressure plate =plate pinch壓板thickness gauge厚薄規cutting die, blanking die沖裁die block模塊folded block折彎塊sliding block滑塊location pin定位銷lifting pin頂料銷die plate, front board模板padding block墊塊stepping bar墊條panel board鑲塊to load a die裝上模具to unload a die 御模具active plate活動板lower sliding plate下滑塊板upper holder block上壓塊upper mid plate上中間板spring box彈簧箱spring-box eject-rod彈簧箱頂spring-box eject-plate彈簧箱頂bushing block襯套cover plate蓋板guide pad導料塊pilot導正筒trim剪外邊pierce剪內邊pocket for the punch head挂鉤slug hole廢料孔radius半徑shim/wedge/heel/pad/spacer/gasket楔子torch-flame cut火焰切割set screw止付螺絲form block折刀round pierce punch =die button圓沖子shape punch =die insert異形子stock located block定位塊metal plate鈑金miller銑床grinder磨床tolerance公差score =groove壓線sliding block滑塊lathe車active plate活動板baffle plate擋塊cover plate蓋板groove punch壓線沖子air-cushion eject-rod氣墊頂桿spring-box eject-plate彈簧箱頂板capability能力parameter參數factor系數driller鉆床set up die架模height of die setting up架模高度analog-mode device類模器inner guiding post內導柱inner hexagon screw內六角螺dowel pin固定銷coil spring彈簧lifter pin頂料銷eq-height sleeves =spool等高套pin銷lifter guide pin浮升導料銷guide pin導正銷wire spring圓線彈簧outer guiding post外導柱stop screw止付螺絲located pin定位銷outer bush外導套press specification沖床規格die height閉模高度flow mark流痕welding mark溶合痕post screw insert螺紋套筒埋self tapping screw自攻螺絲stripper plate脫料板piston活塞handle mold手持式模具flash mold溢流式模具positive mold擠壓式模split mold分割式模具die lifter舉模器top stop上死點bottom stop下死點one stroke一行程to continue, cont.連動to grip(material)吸料location lump, locating piece, locationblock定位塊reset復位to file burr 銼毛刺embedded lump |in'bed| |l mp|鑲塊stamping-missing漏沖to tight a bolt擰緊螺栓to loosen a bolt擰鬆螺栓punched hole沖孔to cut edge =side cut =side scrap 切to bending折彎to pull, to stretch拉伸engraving, to engrave刻印stamping 油印to stake鉚合designing, to design設計design modification 設計脩改成gauge(or jig)治具pedal踩踏板stopper阻擋器flow board流水板torque扭矩spline =the multiple keys花鍵quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel鎢高速moly high speed steel鉬高速forming成型(抽凸,沖凸)draw hole抽孔bending折彎emboss凸點dome凸圓semi-shearing半剪stamp mark沖記號deburr or coin壓毛邊punch riveting沖壓鉚合side stretch側沖壓平reel stretch卷圓壓平groove壓線stamp letter沖字(料號)tick-mark nearside正面壓印tick-mark farside反面壓印extension DWG展開圖procedure DWG工程圖die structure DWG模具結構圖沖壓類punch, press沖punching machine 沖床hydraulic machine油壓機jack升降機decoiler整平機manufacture management製造管理stamping, press沖壓feeder送料機rack, shelf, stack料架taker取料機to reverse material 翻料to load material上料to unload material卸料to return material/stock to退料scraped |'skræpid|報廢scrape ..v.刮;削robot機械手production line流水線packaging tool打包機packaging打包成型類well type蓄料井insulated runner絕緣澆道方式hot runner熱澆道runner plat澆道模塊valve gate閥門澆口band heater環帶狀的電熱器spindle閥針spear head鉋尖頭slag well冷料井cold slag冷料渣air vent排氣道welding line熔合痕eject pin頂出針knock pin頂出銷return pin回位銷反頂針sleeve套筒stripper plate脫料板insert core放置入子runner stripper plate澆道脫料guide pin導銷eject rod (bar)（成型機）頂業subzero深冷處理three plate三極式模具runner system澆道系統stress crack應力電裂orientation定向sprue gate射料澆口，直澆口nozzle射嘴sprue lock pin料頭鉤銷(拉料杆)slag well冷料井side gate側澆口edge gate側緣澆口tab gate搭接澆口film gate薄膜澆口flash gate閘門澆口slit gate縫隙澆口fan gate扇形澆口dish gate因盤形澆口diaphragm gate隔膜澆口ring gate環形澆口submarine gate潛入式澆口tunnel gate隧道式澆口pin gate針點澆口runner less無澆道sprue less 無射料管方式long nozzle延長噴嘴方式spur澆口;溶waste廢料board看板sliding rack滑料架to impose lines壓線to compress, compressing壓縮character die字模to feed, feeding送料material change, stock change材料變更feature change 特性變更prepare for, make preparations for 準備rotating speed, revolution轉速abnormal handling異常處理組裝類Assembly line組裝線Layout布置圖Conveyer流水線運輸帶Rivet machine拉釘機Rivet gun拉釘槍Screw driver起子Electric screw driver電動起子Hydraulic machine 液壓機Pneumatic screw driver氣動起automation自動化to stake, staking, riveting鉚合add lubricant oil加潤滑油argon welding氬焊cylinder油缸robot機械手conveying belt輸送帶transmission rack輸送架to draw holes抽孔bolt螺栓nut 螺母screw 螺絲identification tag標示單screwdriver plug起子插座automatic screwdriver自动啟子to move, to carry, to handle搬be put in storage入庫packing包裝staker = riveting machine鉚合fit together組裝在一起fasten鎖緊(螺絲)fixture 夾具(治具)pallet/skid棧板barcode條碼barcode scanner條碼掃描器fuse together熔合fuse machine/heat stake熱熔機processing, to process加工delivery, to deliver 交貨to return delivery to. to send delivery back to return of goods退easily damaged parts易損件standard parts標準件to lubricate潤滑spring 彈簧spare tools location/buffer手工備品spare molds location模具備品tox machine自鉚機烤漆類phosphate皮膜化成viscosity涂料粘度alkalidipping脫脂main manifold主集流脈organic solvent有機溶劑demagnetization去磁;消磁high-speed transmission高速傳遞heat dissipation熱傳rack上料volatile揮發性degrease脫脂rinse水洗alkaline etch齡咬desmot剝黑膜D.I. rinse純水次Chromate鉻酸處理Anodize陽性處理seal封孔scraped products報放品disposed products處理品dismantle the die折模auxiliary function輔助功能heater band 加熱片thermocouple熱電偶derusting machine除銹機degate打澆口dryer烘干機induction感應induction light感應光response =reaction =interaction感ram連杆edge finder巡邊器concave凸convex凹cold slug冷塊blush 導色gouge溝槽;鑿槽satin texture段面咬花witness line證示線grit沙礫granule =pellet =grain細粒sand blasting噴沙grit maker抽粒機cushion緩沖fillet鑲;嵌邊roller pin formality滾針形式cam driver鍘楔shank摸柄crank shaft曲柄軸品質類qualified products, up-to-grade products良品defective products, not up-to-grade products不良品defective product box不良品箱poor processing 制程不良poor incoming part來件不良exposed metal/bare metal金屬裸露excessive defect過多的缺陷critical defect極嚴重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合規格cosmetic defect外觀不良lack of painting烤漆不到位slipped screw head/slippery slipped thread滑絲missing part漏件wrong part錯件oxidation氧化defective threading抽芽不良poor staking鉚合不良deficient purchase來料不良deficient manufacturing procedure制程不良cosmetic inspection外觀檢查inner parts inspection內部檢查blister 氣泡angular offset 角度偏差dent 壓痕scratch 刮傷deformation 變形filings 鐵削defective label 不良標簽abrasion 磨損Breaking. (be)broken,(be)cracked 斷裂short射料不足nick缺口speck瑕疪shine亮班splay 銀紋gas mark焦痕delaminating起鱗speckle斑點mildewed =moldy = mouldy發霉deformation變形burr(金屬)flash(塑件)毛邊poor staking鉚合不良excessive gap間隙過大grease/oil stains油污inclusion雜質shrinking/shrinkage縮水mixed color雜色fold of packaging belt打包帶折皺painting make-up補漆discoloration羿色water spots水漬impurity 雜質Mismatch 錯位failure, trouble 故障deformation 變形rust 生銹peel 脫漆Shrink 縮水Contamination 臟污water spots 水漬Gap 間隙label error 標簽錯誤Missing label 漏貼rejection criteria 拒收標准Suspected rejects 可疑庇abrasion 損傷、磨損Texture surface 印花紋表面Streak 條紋stains 污點Blotch 斑點discoloration 脫色Inclusion 雜質slug mark 壓痕dirt grime 灰塵blush 毛邊薄膜sink 下凹Hickey 漏漆labels and logos 貼紙與商標Configuration labels 組合貼紙corrugated container 瓦擺紙箱Delaminating 脫層splattering 散點Gouge 銼孔puckering。
工厂常用英语以下是一些工厂常用的英语句子，供您参考：1.This is the material we use to make the product.这是我们制造产品所使用的材料。
2.We have a production line in place to assemble the components.我们有一条生产线用于组装部件。
3.The quality of our products is our top priority.我们最看重产品质量。
4.This machine is used to cut the edges of the sheet material.这台机器是用来切割薄板材料的边缘。
5.The worker uses a die to shape the metal.工人使用模具来成型金属。
6.We need to maintain a clean and safe work environment.我们需要保持一个干净、安全的工作环境。
7.The product must be inspected for defects before shipment.产品在装运前必须经过缺陷检查。
8.We use a computer-numerical-control machine to cut the parts.我们使用数控机床来切割零件。
9.The operator monitors the machines to ensure they are running properly.操作员监视机器的运行状况以确保正常运行。
10.We have a quality control department to ensure our products meet thestandard.我们有一个质量控制部门来确保我们的产品符合标准。
11.This machine is used to drill holes in the metal plate.这台机器是用来在金属板上钻孔的。
