Ver: 1.0 Oct 02, 2002 TEL: 886-3-5788833 1
Global Mixed-mode Technology Inc. G781
±1°C Remote and Local Temperature Sensor with SMBus Serial Interface
Features Two Channels: Measures Both Remote and Local Temperatures No Calibration Required SMBus 2-Wire Serial Interface Programmable Under/Overtemperature Alarms Supports SMBus Alert Response Accuracy: ±1°C (+60°C to +100°C, remote) ±3°C (+60°C to + 100°C, local) 320µA (typ) Average Supply Current During Conversion +3V to +5.5V Supply Range Small 8-Lead SO Package Applications Desktop and Notebook Central Office Computers Telecom Equipment Smart Battery Packs Test and Measurement LAN Servers Multi-Chip Modules Industrial Controllers General Description The G781 is a precise digital thermometer that reports the temperature of both a remote sensor and its own package. The remote sensor is a diode-connected transistor typically a low-cost, easily mounted 2N3904 NPN type that replace conventional thermistors or thermocouples. Remote accuracy is ±1°C with no cali-bration needed. The remote channel can also meas-ure the die temperature of other ICs, such as micro-processors, that contain an on-chip, diode-connected transistor. The 2-wire serial interface accepts standard System Management Bus (SMBus) Write Byte, Read Byte, Send Byte, and Receive Byte commands to program the alarm thresholds and to read temperature data. The data format is 11bits plus sign, with each bit cor-responding to 0.125°C, in two’s-complement format. Measurements can be done automatically and autonomously, with the conversion rate programmed by the user or programmed to operate in a single-shot mode. The adjustable rate allows the user to control the supply current drain. The G781 is available in a small, 8-pin SOP sur-face-mount package. Ordering Information PART* TEMP. RANGE PIN-PACKAGE G781 -20°C to +120°C 8-SOP Pin Configuration Typical Operating Circuit 10k
数据页6ES7414-5HM06-0AB0
SIMATIC S7-400H，CPU 414-5H, 中央组件，用于 S7-400H 和 S7-400F， 5 个接口： 1x MPI/DP,1x DP,1x PN 和 2 个同步模块接口， 4MB 存储器 （2 MB 数据/2 MB 程序）
一般信息
产品类型标志CPU 414-5H PN/DP
硬件功能状态1
固件版本V6.0
附带程序包的
● 工程系统STEP 7 V5.5 SP2 以上，带 HF1
运行中的 CiR 配置
CiR 同步时间，基本负载100 ms
CiR 同步时间，每个输入/输出字节的时间0 µs
电源电压
额定值 (DC)
● DC 24 V否; 通过系统电压进行电压供给
输入电流
来自背板总线 DC 5 V，典型值1.6 A
来自背板总线 DC 5 V，最大值1.9 A
来自背板总线 DC 24 V，最大值150 mA; 每个 DP 接口 150 mA
来自 DC 5 V 接口，最大值90 mA; 在每个 DP 接口处
6ES7414-5HM06-0AB0保留变更权利起始页 1/132018/8/16
© Copyright Siemens功率损失
功率损失，典型值7.5 W
存储器
存储器类型其他
工作存储器
● 集成4 Mbyte
● 集成（用于程序）2 Mbyte
● 集成（用于数据）2 Mbyte
● 可扩展否
装载存储器
● 可扩展 FEPROM是; 附带存储卡（闪存）
● 可扩展 FEPROM，最大值64 Mbyte
● 集成 RAM，最大值512 kbyte
● 可扩展 RAM是
● 可扩展 RAM，最大值64 Mbyte
缓冲
● 存在是
● 带电池是; 所有数据
● 不带电池否
蓄电池
缓冲器电池
● 缓冲器电流，典型值180 µA; 40 °C 以下适用
● 缓冲器电流，最大值1 000 µA
● 缓冲器时间，最大值在模块数据手册中对边界条件和影响系数进行说明
● CPU 上的外部缓冲器电压供电5 V DC 至 15 V DC
Any and all SANYO products described or contained herein do not have specifications that can handleapplications that require extremely high levels of reliability,such as life-support systems,aircraft’scontrol systems,or other applications whose failure can be reasonably expected to result in seriousphysical and/or material damage. Consult with your SANYO representative nearest you before usingany SANYO products described or contained herein in such applications.SANYO assumes no responsibility for equipment failures that result from using products at values thatexceed,even momentarily, rated values (such as maximum ratings,operating condition ranges,or otherparameters) listed in products specifications of any and all SANYO products described or containedherein.Monolithic Linear IC
1 to 2.3W 2-Channel of Power AmplifierOrdering number:ENN919DLA4192
The information provided in this documentation contains general descriptions and/or technical characteristics of the performance of the products contained herein.
This documentation is not intended as a substitute for and is not to be used for determining suitability or reliability of these products for specific user applications.
It is the duty of any such user or integrator to perform the appropriate and complete risk analysis, evaluation and testing of the products with respect to the relevant specific application or use thereof.
Neither Schneider Electric Industries SAS nor any of its affiliates or subsidiaries shall be responsible or liable for misuse of the information contained herein.Jan 5, 20201Product data sheetCharacteristicsATV71HC40N4
variable speed drive ATV71 - 400kW-600HP -480V - EMC filter-graphic terminalProduct availability: Stock - Normally stocked in distribution facility
