信赖性测试报告
- 格式:doc
- 大小:225.00 KB
- 文档页数:12
Reliability Test Report
信赖性测试报告
Test No./测试编号:0110219
Model/电芯型号:463455—520mAh Department/部门:质管部
Date/日期:2011-02-19
Contents
一、外部短路External short-circuit (3)
二、强制放电Forced discharge (4)
三、过充电Overcharge (5)
四、穿刺Puncture (6)
五、震动Vibration (7)
六、跌落Drop (8)
七、重物冲击Impact (9)
八、挤压Crush (10)
九、温度循环Temperature cycling (11)
十、热冲击Heating (12)
十一、投射物实验Projectile (13)
十二、恒定湿热Constant humidity (14)
Remarks/备注:
1. Standard charge/充电标准:在20±5℃条件下,先以0.8C电流充电至截止电压,再以设计上限充电电
压(单体4.20V)恒压充电,截至电流为0.01CA
2. Verification and Identification/鉴定检验:鉴定检验一般在产品设计定型和生产定型时进行,但在产品的主要设计、工艺、元器件及材料有重大改变,且改变之参数影响产品的重要性能,使原有的鉴定结论不再有效时也应进行鉴定检验。
3. Sampling plan/抽样方案:鉴定检验的样品由批量生产的电池中随机抽取。
4. Criterion rule /判定规则:当所有检验项目均满足标准时则判为鉴定检验合格。
5.Weight Loss/
6. Difinition/
(一)、Conclusion/测试结果
External Short Circuit 外部短路
1. The cells are full charge under strict observation of the standard charging, and let stand for 1 hour. 将电池恒流恒压满充至4.2V,然后静置1h。
2. Put the samples in an oven with 60±2℃.
将感温探头贴到电池表面,装到短路装置上,然后放置到60±2℃的高温箱中。
3. Short each cell with copper wire having maximum resistance load of 50mΩ, monitor and keep 1 hour.
待电池表面温度达到60℃后,用50毫欧的铜导线将电池进行短路,保持短路状态1h。
4. Measure temperature of the exterior cell and observe the samples.
记录实验过程中的最高温度
Test requirements 实验要求:N ot explode or catch fire. The temperature of the exterior cell or battery casing shall not
exceed150°C (302°F)/不起火,不爆炸,电池表面温度<150℃
DATA 实验数据:
样品照片过程照片实验后照片
二、Forced discharge 强制放电:
1. The cells are full charge under strict observation of the standard charging, and let stand for 1 hour.
将电池恒流恒压满充至4.2V,静置1h。
2. Completely discharge one cell of the samples with 1C current,
将其中一个电池用1C的电流完全放电。
3.The completely discharged cell is to be force-discharged by connecting it in series with the fully charged cells; the sample is to discharge until the battery case temperature has returned to ambient temperature.
将满充电池和上述完全放电的带电池串联进行强制放电,直至完全放电且电池温度接近室温。
Test requirements 实验要求:N ot explode or catch fire/不爆炸、不起火
DATA
样品照片过程照片实验后照片
三、Overcharge 过充电:
1. Discharge all cells to 3.0V with 1C current.
将电池用1C的电流放电至3.0V。
2. Charge cell (without PTC) with 1C current and 5V voltage, and keep at least 24 hours.
设定充电电压5.0V,充电电流为1C,将电池充电24h
Test requirements 实验要求:N ot explode or catch fire. The temperature of the exterior cell or battery casing shall not
exceed 150°C (302°F)./不起火,不爆炸,电池表面温度<150℃
DATA
样品照片过程照片实验后照片
四、Puncture 穿刺
1. The cells are full charge under strict observation of the standard charging, and let stand for 1 hour.