MAX130CMH+T;MAX131CMH+TD;MAX130CMH+;MAX131CMH+D;MAX130CPL+3;中文规格书,Datasheet资料

MAX13485E/MAX13486EHalf-Duplex RS-485/RS-422 Transceivers in µDFN

ELECTRICAL CHARACTERISTICS (continued)(VCC= +5V ±5%, TA= TMINto TMAX, unless otherwise noted. Typical values are at VCC= +5V and TA= +25°C.) (Notes 1, 2)PARAMETERSYMBOLCONDITIONSMINTYPMAXUNITSOutput-Low VoltageVOLIO = 1mA, VA - VB < -VTH0.4VTri-State Output Current atReceiverIOZR0V < VO < VCC±1µAReceiver Input ResistanceRIN-7V < VCM < +12V48kΩReceiver-Output Short-CircuitCurrentIOSR0V < VRO < VCC±7±95mAPOWER SUPPLYSupply VoltageVCC4.755.25VSupply CurrentICCDE = 1, RE = 0, no load4.5mAShutdown Supply CurrentISHDNDE = 0, RE = 110µAESD PROTECTIONAir Gap Discharge IEC61000-4-2(MAX13485E)±15ESD Protection (A, B)Human Body Model±15kVESD Protection (All Other Pins)Human Body Model±2kVSWITCHING CHARACTERISTICS—MAX13485E(VCC= +5V ±5%, TA= TMINto TMAX, unless otherwise noted. Typical values are at VCC= +5V and TA= +25°C.) (Note 1)PARAMETER

M

XM

ZF

XF

ZM

YHG 12A

0

010002500.10.20.30.7

5007500.6

0.5

0.4LOAD DATATIMING DIAGRAM

Stroke [mm]Movement time [s]5 kg 2.5 kgTECHNICAL DATA

UVoltage range:200-600 V

AC rms

a

MaxMax. acceleration:40 m/s2

v

MaxMax. speed:4 m/s

F

N motNominal force:33 N

F

P motPeak force:102 N

I

PPeak current:2 A

Temperature monitoring:PTC

s

MaxMax. stroke:bis 1000 mm in 100 mm

Repeat accuracy:0.005 mm

m

recMax. recommended load:5 kg

m

gui 0Mass of the guide rail

with 0 mm stroke:1.44 kg

m

gui 100Mass of the guide rail

per 100 mm stroke:0.72 kg

m

carrMass of the carriage with motor:

1.45 kgM

X statMax. static moment about the X-axis:150 Nm

M

Y statMax. static moment about the Y-axis:40 Nm

M

Z statMax. static moment about the Z-axis:150 Nm

F

X statMax. static force in the Y-axis:150 N

F

Z statMax. static force in the Z-axis:300 N

M

X dynMax. dynamic moment about the X-axis:20 Nm

精心整理

精心整理 MAX912/MAX913

————单/双路，超高速，低功耗，精密的TTL比较器

1.总体描述

MAX913（单）和MAX912（双）高速，低功耗比较器是一个拥有独特设计就是在其线性区域是它的比较是可以防止振荡。没有要求最低输入转换率。它是由差分输入和互补的TTL输出。快速传播延迟（10ns的典型值），具有极低的电源电流和宽共模输入范围，包括负电流使MAX912/MAX913达到的低功耗理想效果，高速，单电源+5V（或±5V）的应用，例如有V/F转换器和开关稳压器。

MAX912/MAX913保持着稳定的线性区域输出。此功能消除了常见的在输出不稳定时产生高速驱动时具有的比较滞销输入信号。

该MAX912/MAX913可以单一+5V电源供电或±5V的分别供应。该MAX913是一个

改进的LT1016的替代品。在输入一小能量时它提供了更宽的输入电压范围和等效速度。在MAX912双比较具有同等性能的MAX913并且包括独立的锁存控制功能。

2.应用

过零检测器

以太网线接收器

开关稳压器

高速采样电路

高速触发器

扩展范围的V/F转换器

快速脉冲宽度/高度的判别

3.特点

超快速（为10ns）

单+5V或±5V的双电源供电

输入范围扩展至负电源以下

低功耗：6毫安（+5V）的每次比较

无最小输入信号摆率的要求

无电源电流扣球

稳定的线性区

可投入任一电源

低失调电压：0.8mV

4.引脚配置

顶视图：

5.绝对最大额定值：

正电源电压................................................7V

负电源电压..............................................-7V 精心整理

精心整理 差分输入电压.......................................±15V

输入电压....................................-0.3V至15V

General Description

The MAX13080E–MAX13089E +5.0V, ±15kV ESD-protect-

ed, RS-485/RS-422 transceivers feature one driver and

one receiver. These devices include fail-safe circuitry,

guaranteeing a logic-high receiver output when receiver

inputs are open or shorted. The receiver outputs a logic-

high if all transmitters on a terminated bus are disabled

(high impedance). The MAX13080E–MAX13089E include

a hot-swap capability to eliminate false transitions on the

bus during power-up or hot insertion.

The MAX13080E/MAX13081E/MAX13082E feature

reduced slew-rate drivers that minimize EMI and

reduce reflections caused by improperly terminated

cables, allowing error-free data transmission up to

250kbps. The MAX13083E/MAX13084E/MAX13085E

also feature slew-rate-limited drivers but allow transmit

speeds up to 500kbps. The MAX13086E/MAX13087E/