DIN标准与GB国标参考对照表分析

序号DIN 英文名称EN ISO GB 中文名称1DIN 1 taper pins EN 22339 ISO 2339 GB/T 117 圆锥销2DIN 1052 washers for timber connectors 木材连接用垫圈3DIN 11024 spring cotters 弹簧卡子4DIN 1151 round plain head nails 沉头钢钉5DIN 125－1 plain washers without chamfer ISO 7089 GB/T 97.1 平垫圈 A 级6DIN 125－2 plain washers with chamfer ISO 7090 GB/T 97.2 平垫圈倒角型 A 级7DIN 126 plain washers ISO 7091 GB/T 95 平垫圈 C 级8DIN 127－1 spring lock washers with tang ends GB/T 7244 重型弹簧垫圈9DIN 127－2 spring lock washers with square ends GB/T 93 标准弹簧垫圈10DIN 128 curved spring lock washers GB/T 7245 鞍形弹簧垫圈11DIN 13257 belting bolts (elevator bolts) 平板螺栓12DIN 137 wave spring washers GB/T 955 波形弹性垫圈13DIN 1440 plain washers for clevis pins EN 28738 ISO 8738 GB/T 97.3 销轴用平垫圈14DIN 1441 Washers, Type Coarse for Bolts 螺栓用粗制垫圈15DIN 1444 clevis pins with head EN 22341 ISO 2341 GB/T 882 销轴16DIN 1471 grooved pins, taper grooved ISO 8744 GB/T 13829.2 槽销锥槽（A 型）17DIN 1472 grooved pins, taper grooved half length ISO 8745 GB/T 13829.2 槽销锥槽（B 型）18DIN 1473 grooved pins, parallel grooved full length ISO 8740 GB/T 13829.1 槽销平行沟槽（B 型）19DIN 1474 grooved pins, reserve grooved half length ISO 8741 GB/T 13829.2 槽销锥槽（C 型）20DIN 1475 grooved pins, centre grooved ISO 8742 GB/T 13829.1 槽销平行沟槽（C 型）21DIN 1476 grooved pins with round head ISO 8746 GB/T 13829.3 槽销圆头、沉头（A 型）22DIN 1477 grooved pins with countersunk head ISO 8747 GB/T 13829.3 槽销圆头、沉头（B 型）23DIN 1479 turnuckles(centre parts), made out of hexagon bar 六角螺母棒24DIN 1480 turnuckles with eye bolt and hook bolt 花篮螺栓25DIN 1481 spring pins, heavy type ISO 8752 GB/T 879.1 弹性圆柱销直槽重型26DIN 1587 hexagon domed cap nuts GB/T 802 组合式盖形螺母序号DIN 英文名称EN ISO GB 中文名称27DIN 1804 slotted round nuts for hook spanner 开槽圆螺母（配合沟头扳手）28DIN 1816 round nuts with set holes 圆螺母（带插销孔）29DIN 18182 dry wall screws 干壁钉（墙板钉）30DIN 186 T－head bolts with square neck GB/T 37 T 型槽用螺栓31DIN 188 T－head bolts with double nip T 型双接头螺栓32DIN 2093 disc springs 盘型弹簧垫圈33DIN 258 taper pins with threaded end ISO 8737 GB/T 881 螺尾锥销34DIN 261 T－head bolts T 型头螺栓35DIN 28129 Clamp nuts for covers36DIN 3017 hose clamps 喉箍37DIN 315 wing nuts with rounded wings GB/T 62 蝶型螺母38DIN 316 wing screws Amercia form 蝶型螺钉(美制)39DIN 317 wing screws Germany form 蝶型螺钉(德制)40DIN 319 ball knobs 圆球型盖型螺母41DIN 3404 lubricating nipples, button head JB/T 7490.1 直通式压注油杯42DIN 3567 shackles for conduilts 管夹43DIN 3570 stirrup bolts (U－bolts) U 型螺栓44DIN 404 slotted capstan screws GB/T 832 开槽带孔球面圆柱头螺钉45DIN 417 slotted set srews with full dog point EN 27435 ISO 7435 GB/T 75 开槽长圆柱端紧定螺钉46DIN 427 slotted set srews with chamfered end ISO 234247DIN 431 pipe nuts with thread as in ISO 228－148DIN 432 external tab washers (locking tab washers) GB/T 856 外舌止动垫圈49DIN 433 washers for cheese head screws ISO 7092 GB/T 848 小垫圈 A 级50DIN 434square taper washers for U－section GB/T 853 槽钢用方斜垫圈51DIN 435 square taper washers for I－sections GB/T 852 工字钢用方斜垫圈52DIN 436 square washers 方垫圈序号DIN 英文名称EN ISO GB 中文名称53DIN 438 slotted set screws with cup point EN 27436 ISO 7436 GB/T 74 开槽凹端紧定螺钉54DIN 439－1 Hexagon thin nuts (unchamfered) －Product grade B ISO 4036 GB/T 6174 六角薄螺母无倒角55DIN 439－2 Hexagon thin nuts (chamfered) －Product grades Aand BISO 4035 GB/T 6172.1 六角薄螺母56DIN 440 rounds washers for wood constructions ISO 8675ISO 7094木螺钉专用垫圈57DIN 443 sealing caps, push－in type 密封帽58DIN 444 eyebolts GB/T 798 活节螺栓59DIN 462 internal tab washers 内舌止动垫圈60DIN 463 tab washers with short and long tab at right angles GB/T 855 双耳止动垫圈61DIN 464 knurled thumb screws with collar GB/T 834 滚花高头螺钉62DIN 465 slotted knurled thumb screws with collar 开槽滚花高头螺钉63DIN 466 knurled nuts with collar GB/T 806 滚花高螺母64DIN 467 knurled nuts GB/T 807 滚花薄螺母65DIN 470 sealing washers 锁紧垫圈66DIN 471 retaining rings for shafts (external), circlips GB/T 894.1 轴用弹性挡圈－A 型67DIN 472 retaining rings for bores (internal), circlips GB/T 893.1 孔用弹性挡圈－A 型68DIN 478 square head bolts with collar 方头带垫螺栓69DIN 479 square head bolts with half dog point 方头圆柱底端螺栓70DIN 480 square head bolts with collar, half dog point androunded end方头带垫半圆底端螺栓71DIN 508 T－slot nuts ISO 299 T 型槽螺母72DIN 525 single end studs 单头螺柱73DIN 529 masonry bolts GB/T 799 地脚螺栓74DIN 546 slotted round nuts GB/T 817 带槽圆螺母75DIN 547 round nuts with drilled holes in one face GB/T 815 端面带孔圆螺母序号DIN 英文名称EN ISO GB 中文名称76DIN 551 slotted set screws with flat point EN 24766 ISO 4766 GB/T 73 开槽平端紧定螺钉77DIN 553 slotted set screws with cone point EN 27434 ISO 7434 GB/T 71 开槽锥端紧定螺钉78DIN 555 hexagon nuts ISO 4034 GB/T 41 六角螺母 C 级79DIN 557 Product grade C square nuts GB/T 39 方螺母 C 级80DIN 558 hexagon screws ISO 4018 GB/T 5781 六角头螺栓全螺纹 C 级81DIN 561 hexagon set screws with full dog point 六角头圆柱端紧定螺钉82DIN 562 square thin nuts －Product grade B 方型薄螺母 B 级83DIN 571 hexagon head wood screws (coach screws) GB/T 102 六角头木螺钉84DIN 580 lifting eye bolts ISO 3266 GB/T 825 吊环螺钉85DIN 582 lifting eye nuts 吊环螺母86DIN 601 hexagon bolts ISO 4016 GB/T 5780 六角头螺栓 C 级87DIN 603 mushroom head square neck bolts (carriage bolts) ISO 8677 GB/T 14 大半圆头方颈螺栓88DIN 604 flat countersunk nib bolts 沉头带插销马车螺栓89DIN 605 flat countersunk long square neck bolts 沉头长方颈马车螺栓90DIN 607 cup head nib bolts 半圆头带插销马车螺栓91DIN 608 flat countersunk short square neck bolts 沉头短方颈马车螺栓92DIN 609 hexagon fitted bolts, long thread 六角头精配螺栓（长螺纹）93DIN 610 hexagon fitted bolts, short thread 六角头精配螺栓（短螺纹）94DIN 6303 Knurled nuts95DIN 6319 spherical washers, conical seats96DIN 6325 parallel pins ISO 8734 GB/T 119.2 圆柱销淬硬钢和马氏体不锈钢97DIN 6330 hexagon nuts, 1.5d GB/T 56 厚六角螺母98DIN 6331 hexagon nuts, 1.5d with collar 厚六角法兰面螺母99DIN 6334 hexagon nuts, 3d 长六角螺母100DIN 653 knurled thumb screws thin type GB/T 835 滚花平头螺钉101DIN 660round head rivets ISO 1051 GB/T 867 半圆头铆钉序号DIN 英文名称EN ISO GB 中文名称102DIN 661 countersunk head rivets ISO 1051 GB/T 869 沉头铆钉103DIN 662 raised contersunk head rivets ISO 1051 GB/T 870 半沉头铆钉104DIN 674 mushroom head rivets ISO 1051 大扁头铆钉105DIN 6797 (A) toothed lock washers (with external teeth) GB/T 862.1 外齿锁紧垫圈106DIN 6797 (J) toothed lock washers (with internal teeth) GB/T 861.1 内齿锁紧垫圈107DIN 6798 (A) serrated lock washers (with external teeth) GB/T 862.2 外锯齿锁紧垫圈108DIN 6798 (J) serrated lock washers (with internal teeth) GB/T 861.2 内锯齿锁紧垫圈109DIN 6799 retaining rings for shafts (E－rings), circlips GB/T 896 开口挡圈110DIN 6885 parallel keys(form A ) ISO 773/2491 平键（A 型）111DIN 6888 woodruff keys ISO 3912 GB/T 1099 半圆键112DIN 6899 thimbles 嵌环（支撑环）113DIN 6900－1 screws and washers assemblies ISO 10644 GB/T 9074.1 螺栓或螺钉和平垫圈组合件114DIN 6901 tapping screws and washers assemblies ISO 10510 GB/T 9074.18 自攻螺钉和平垫圈组合件115DIN 6912 hexagon socket thin head cap screws with pilot recessfor wrench key矮头内六角圆柱头螺钉116DIN 6914 High－strength hexagon head bolts with large widthsacross flats for structural steel boltingGB/T 18230.1GB/T 18230.2栓接结构用大六角头螺栓螺纹长度按GB/T 3106 C 级8.8 和10.9 级栓接结构用大六角头螺栓短螺纹长度C 级8.8 和10.9 级117DIN 6915 Steel hexagon nuts with large widths across flats forhigh－strength structural boltingGB/T 18230.4 栓接结构用1 型大六角螺母 B 级10 级118DIN 6916 round washers for friction grip bolts GB/T 18230.5 栓接结构用平垫圈淬火并回火119DIN 6917 spuare taper washers for friction grip bolts on T－sections120DIN 6921 Hexagon flange bolt EN 1665121DIN 6922 EN 1665E:\lee\技术文档\DIN 和ISO、国内标准参考对照表－紧固件.doc page 5 of 10序号DIN 英文名称EN ISO GB 中文名称122DIN 6923 hexagon flange nuts EN 1661 ISO 4161 GB/T 6177.1 六角法兰面螺母123DIN 6924 Prevailing torque type hexagon nuts with nylon insert ISO 7040 GB/T 889.1 1 型非金属嵌件六角锁紧螺母ISO 10512 GB/T 889.2 1 型非金属嵌件六角锁紧螺母细牙124DIN 6925 prevailing torque type hexagon nuts, all metallic nuts ISO 7042 GB/T 6185.1 2 型全金属六角锁紧螺母125DIN 6926 Prevailing torque type hexagon nuts with flange (with EN 1663 ISO 7043 GB/T 6183.1 非金属嵌件六角法兰面锁紧螺母nylon insert) EN 1666 ISO 12125 GB/T 6183.2 非金属嵌件六角法兰面锁紧螺母细牙126DIN 6927 Prevailing torque type all metal hexagon nuts with flange EN 1664 ISO 7044 GB/T 6187.1 全金属六角法兰面锁紧螺母EN 1667 ISO 12126 GB/T 6187.2 全金属六角法兰面锁紧螺母细牙127DIN 7 parallel pins ISO 2338 GB/T 119.1 圆柱销不淬硬钢和奥氏体不锈钢128DIN 703 adjusting rings, heavy range (shafting collars)129DIN 705 adjusting rings, light range (shafting collars)130DIN 70952 tab washers for slotted round nuts GB/T 858 圆螺母用止退垫圈131DIN 7337 blind rivets GB/T12617/12618开口型抽芯铆钉（沉头、扁圆头）132DIN 7338 rivets for brake and clutch lining GB/T 875/975 扁平头半空心/全空心铆钉133DIN 7343 spiral pins ISO 8750 GB/T 879.4 弹性圆柱销卷制标准型134DIN 7344 Spiral pin, heavy duty ISO 8748 GB/T 879.3 弹性圆柱销卷制重型135DIN 7346 spring pins, light type ISO 13337 GB/T 879.2 弹性圆柱销直槽轻型136DIN 7349 washers for bolts with heavy type spring pins 重型弹性圆柱销用垫圈137DIN 741 wire rope clips 卡头138DIN 7500 threadforming screws for ISO －metric thread ISO 公制螺纹螺钉(多种头型)6 10序号DIN 英文名称EN ISO GB 中文名称ISO 10666 GB/T 3098.11 紧固件机械性能自钻自攻螺钉ISO 15480 GB/T 15856.5 六角凸缘自钻自攻螺钉139DIN 7504 self－drilling tapping screwsISO 15481 GB/T 15856.1 十字槽盘头自钻自攻螺钉ISO 15482 GB/T 15856.2 十字槽沉头自钻自攻螺钉ISO 15483 GB/T 15856.3 十字槽半沉头自钻自攻螺钉140DIN 7513 thread cutting screws 开槽切削螺纹螺钉(多种头型)141DIN 7516 thread cutting screws cross recess 十字槽切削螺纹螺钉(多种头型)142DIN 787 T－slot screws ISO 299 T 型槽螺钉143DIN 7965 tee nuts with pronge T 型四爪螺母144DIN 7968 hexagon head fitted bolts for steel structures145DIN 7971 pan head tapping screws with slot ISO 1481 GB/T 5282 开槽盘头自攻螺钉146DIN 7972 countersunk flat head tapping screws with slot ISO 1482 GB/T 5283 开槽沉头自攻螺钉147DIN 7973 raised countersunk oval head tapping screws with slot ISO 1483 GB/T 5284 开槽半沉头自攻螺钉148DIN 7976 hexagon tapping screws ISO 1479 GB/T 5285 六角头自攻螺钉149DIN 7980 spring lock washers for screws with cylindrical heads 圆柱头螺钉用弹簧垫圈150DIN 7981 pan head tapping screws with cross recessed ISO 7049 GB/T 845 十字槽盘头自攻螺钉151DIN 7982 countersunk flat head tapping screws with crossrecessedISO 7050 GB/T 846 十字槽沉头自攻螺钉152DIN 7983 raised countersunk oval head tapping screws with crossrecessedISO 7051 GB/T 847 十字槽半沉头自攻螺钉153DIN 7984 hexagon socket head cap screws with, reduced head 薄型内六角圆柱头螺钉154DIN 7985 pan head screws with cross recessed ISO 7045 GB/T 818 十字槽盘头螺钉155DIN 7989 washers for steel structures序号DIN 英文名称EN ISO GB 中文名称GB/T 5780 六角头螺栓 C 级156DIN 7990 hexagon head bolts for steel structuresGB/T 41 六角螺母 C 级GB/T 6170 1 型六角螺母157DIN 7991 hexagon socket countersunk head screws ISO 10642 GB/T 70.3 内六角沉头螺钉158DIN 7993 roundwire snap rings for shafts GB/T 895.2 轴用钢丝挡圈159DIN 7995 cross recessed raised countersunk head wood screws GB/T 952 十字槽半沉头木螺钉160DIN 7996 cross recessed round head wood screws GB/T 950 十字槽圆头木螺钉161DIN 7997 cross recessed countersunk head wood screws GB/T 951 十字槽沉头木螺钉162DIN 8140 coil inserts, coarse, fine thread, self locking 螺纹护套（普通\自锁等）163DIN 835 studs－metal (end=2d) GB/T 900 双头螺柱bm=2d164DIN 84 slotted cheese head screws ISO 1207 GB/T 65 开槽圆柱头螺钉165DIN 85 slotted pan head screws ISO 1580 GB/T 67 开槽盘头螺钉166DIN 9021 washers, outside diameter appro.3d ISO 7093－1 GB/T 96.1 大垫圈 A 级ISO 7093－2 GB/T 96.2 大垫圈 C 级167DIN 906 hexagon socket pipe plugs, conical thread 内六角锥型闭锁螺钉168DIN 908 hexagon socket screw plugs, cyl. thread 内六角直型闭锁螺钉169DIN 909 hexagon head pipe plugs, conical thread 外六角锥型闭锁螺钉170DIN 910 hexagon head screw plugs, cyl.thread 外六角直型闭锁螺钉171DIN 911 socket wrenches ISO 2936 内六角扳手172DIN 912 hexagon socket cap screws ISO 4762 GB/T 70.1 内六角圆柱头螺钉173DIN 913 hexagon socket set screws with flat point ISO 4026 GB/T 77 内六角平端紧定螺钉174DIN 914 hexagon socket set screws with cone point ISO 4027 GB/T 78 内六角锥端紧定螺钉175DIN 915 hexagon socket set screws with dog point ISO 4028 GB/T 79 内六角圆柱端紧定螺钉176DIN 916 hexagon socket set screws with cup point ISO 4029 GB/T 80 内六角凹端紧定螺钉177DIN 917 hexagon cap nuts 薄型盲螺母178DIN 920 slotted short cheese head screws 开槽小圆柱头螺钉序号DIN 英文名称EN ISO GB 中文名称179DIN 921 slotted large cheese head screws GB/T 833 开槽大圆柱头螺钉180DIN 923 slotted pan head screws with shoulder GB/T 830 开槽圆柱头轴位螺钉181DIN 927 slotted shoulder screws GB/T 831 开槽无头轴位螺钉182DIN 928 square weld nuts GB/T 13680 焊接方螺母183DIN 929 hexagon weld nuts GB/T 13681 焊接六角螺母184DIN 93 tab washers with long tab GB/T 854 单耳止动垫圈185DIN 931－1 hexagon head screws ISO 4014 GB/T 5782 六角头螺栓186DIN 933 hexagon head screws－Product gardes A and B ISO 4017 GB/T 5783 六角头螺栓全螺纹187DIN 934 hexagon full nuts ISO 4032 GB/T 6170 1 型六角螺母ISO 8673 GB/T 6171 1 型六角螺母细牙188DIN 935 Hexagon slotted nuts and castle nuts ISO 7035 GB/T 6178 开槽六角螺母189DIN 936 hexagon thin nuts ISO 4035 GB/T 6172.1 六角薄螺母190DIN 937 hexagon thin slotted and castle nuts ISO 7038 GB/T 6181 六角开槽薄螺母－A 和B 级191DIN 938 studs metal (end=1d) GB/T 897 双头螺柱bm=1d 192DIN 939 studs metal (end=1.25d) GB/T 898 双头螺柱bm=1.25d 193DIN 94 split pins ISO 1234 GB/T 91 开口销194DIN 940 studs metal (end=1.5d) GB/T 899 双头螺柱bm=1.5d 195DIN 95 slotted raised countersunk head wood screws GB/T 101 开槽半沉头木螺钉196DIN 96 slotted round head wood screws GB/T 99 开槽圆头木螺钉197DIN 960 hexagon head bolts, metric fine pitch thread ISO 8765 GB/T 5785 六角头螺栓细牙198DIN 961 hexagon head bolts, metric fine pitch thread ISO 8676 GB/T 5786 六角头螺栓细牙全螺纹199DIN 962 additional shapes and versions for bolts 头部穿孔六角头螺栓200DIN 963 slotted countersunk head screws ISO 2009 GB/T 68 开槽沉头螺钉201DIN 964 slotted raised countersunk oval head screws ISO 2010 GB/T 69 开槽半沉头螺钉序号DIN 英文名称EN ISO GB 中文名称ISO 7046－1 GB/T 819.1 十字槽沉头螺钉第1 部分：钢4.8 级202DIN 965 cross recessed countersunk head screwsISO 7046－2 GB/T 819.2 十字槽沉头螺钉第2 部分：钢8.8、不锈钢A2－70 和有色金属CU2 或CU3203DIN 966 cross recessed raised countersunk head screws ISO 7047 GB/T 820 十字槽半沉头螺钉204DIN 97 slotted countersunk head wood screws GB/T 100 开槽沉头木螺钉205DIN 970 Hexagon nuts, style 1, Product grades A and B ISO 4032 GB/T 6170 1 型六角螺母206DIN 971－1 Hexagon nuts, style 1, with metric fine pitch threadProduct grades A and BISO 8673 GB/T 6171 1 型六角螺母细牙207DIN 971－2 Hexagon nuts, style 2, with metric fine pitch thread －Product grades A and BISO 8674 GB/T 6176 2 型六角螺母细牙208DIN 972 hexagon nuts, Product grade C ISO 4034 GB/T 41 六角螺母 C 级209DIN 975 threaded rods(studDIN gs) GB/T 15389 螺杆210DIN 976 threaded pins(stud bolts) 螺纹销211DIN 977 Hexagon weld nuts with flange212DIN 979 Hexagon thin slotted and castle nuts with metric coarseand fine pitch thread－Product grade A and B六角开槽薄螺母（2 型）213DIN 980 prevailling torque type hexagon nuts, all metall nuts ISO 7042 GB/T 6185.1 2 型全金属六角锁紧螺母ISO 10513 GB/T 6185.2 2 型全金属六角锁紧螺母214DIN 981 locknuts ISO 2982－2215DIN 982 prevailling torque type hexagon nuts, heavy type, with ISO 7040 GB/T 889.1 1 型非金属嵌件六角锁紧螺母nylon insert ISO 10512 GB/T 889.2 1 型非金属嵌件六角锁紧螺母细牙216DIN 985 prevailling torque type hexagon nuts, heavy type, withnylon insertISO 10511 GB/T 6172.2 非金属嵌件六角锁紧薄螺母217DIN 986 prevailling torque typedomed capnuts with nylon insert 六角盖型尼龙锁紧螺母218DIN 988 shim rings 配合垫圈与支承垫圈E:\lee\技术文档\DIN 和ISO、国内标准参考对照表－紧固件.doc page 10 of 10。

德标与国标对照表德标与国标对照表德国标准（DIN）和中国国家标准（GB）是两个不同国家的标准化组织所制定的标准。

虽然有相似之处，但在某些领域有所不同。

以下是德标与国标的对照表。

一、电气工程1. 电线和电缆德标：DIN VDE 0250国标：GB 50232. 无绝缘导体德标：DIN EN 60228国标：GB/T 39563. 低压电器德标：DIN EN 60 439-1 国标：GB 14048.14. 高压开关设备德标：DIN 43620国标：GB 19845. 潜水电泵德标：DIN 24255国标：GB/T 281-2004二、机械工程1. 标准零件德标：DIN 931/1国标：GB/T 57822. 对焊接德标：DIN 8563/1-3国标：GB/T 985-1998 3. 货物运输德标：DIN 15185国标：GB/T 121834. 机床德标：DIN 863国标：GB/T 108605. 尺寸公差德标：DIN EN ISO 2768 国标：GB/T 1804-2000 三、建筑工程1. 路面标准德标：DIN 18035国标：GB 504872. 接缝放样德标：DIN 18202国标：GB 505813. 钢筋连接德标：DIN 1045国标：GB 14994. 建筑钢材德标：DIN 488国标：GB/T 706-1988 5. 水泥制品德标：DIN 18550国标：GB/T 11785以上是德标与国标的对照表，可以看到，在不同领域，德标与国标相比有些区别。

因此，在进行相关工程和产品设计时，需要根据当地标准进行设计和生产，以满足当地需求。

德国标准和国际标准、中国标准中英文对照表序号德国标准中文品名英文品名国际标准中国标准Description inItem D IN-StandardDescription in English ISO-Standard GB-Standard Chinese1 DIN1 圆锥销taper pins ISO2339 GB1172 DIN7 圆柱销parallel pins ISO2338 GB119-863 DIN84 开槽圆柱头螺钉slotted cheese head screws ISO1207 GB65-854 DIN85 开槽盘头螺钉slotted pan head screws ISO1580 GB67-855 DIN93 单耳止动垫圈tab washers GB8546 DIN94 开口销split cotter pins ISO1234 GB91slotted raised csk head wood7 DIN95 开槽半沉头木螺钉GB101screws8 DIN96 开槽半圆头木螺钉slotted round head wood screws GB99slotted countersunk head wood9 DIN97 开槽沉头木螺钉GB100screws10 DIN125-A 平垫plain washers ISO7089 GB97.1-8511 DIN125-B 平垫(带倒角) mediun washers ISO7090 GB97.2-8512 DIN126 平垫plain washers ISO709113 DIN127-A 重型弹垫spring lock washers,tang ends GB724414 DIN127-B 标准弹垫spring lock washers,square ends GB93-8715 DIN128-A 鞍形弹垫single coil spring lock washers GB7245-8716 DIN137-A 弹簧止动垫圈curved spring washers17 DIN137-B 波形弹垫wave spring washers GB95518 DIN186 T型方颈螺栓T-head bolts with square neck GB 37-8819 DIN188 T型双接头螺栓T-head bolts with double nip20 DIN258 螺纹圆锥销taper pins with threaded end ISO873721 DIN261 T型头螺栓T-head bolts22 DIN315AF 蝶型螺母(美制) wing nuts amercia form23 DIN315DF 蝶型螺母(德制) wing nuts germany form GB62-8824 DIN316AF 蝶型螺钉(美制) wing screws amercia form25 DIN317DF 蝶型螺钉(德制) wing screws germany form26 DIN319 圆球型盖型螺母ball knobs27 DIN404开槽带孔球面圆柱头螺钉slotted capstan screws GB832-8828 DIN417开槽长圆柱端紧定螺钉slotted set srews with full dogpointISO7435 GB75-8529 DIN427开槽平端紧定螺钉(半牙) slotted set srews with chamferedendISO2342 GB73-8530 DIN431小六角特薄细牙螺母pipe nuts with thread GB808-8831 DIN432 外舌止动垫圈external tap GB856-8832 DIN433小垫圈(用于圆柱头螺钉)washers for cheese head screws ISO7092 GB848-95 33 DIN434 方斜垫圈(U型)square taper washers forU-sectionGB852-88 34 DIN435 方斜垫圈(I型)square taper washers forI-sectionsGB852-8835 DIN436 方垫圈square washers36 DIN438 开槽凹端紧定螺钉slotted set with cup point ISO7436 GB74-8537 DIN439 六角薄螺母hexagon thin nuts ISO4035 GB6172-8638 DIN439 细牙六角薄螺母hexagon thin nuts ISO8675 GB6173-8639 DIN440 木螺钉专用垫圈rounds washers for woodconstructionsISO709440 DIN443 密封帽sealing caps,push-in type41 DIN444 活节螺栓B 型eye bolts form B GB798-8842 DIN462 内舌止动垫圈internal tab washers43 DIN463 双耳止动垫圈washers with two taps GB855-8844 DIN464 滚花高头螺钉knurled thumb screws withcollarGB834-88 45 DIN465 开槽滚花高头螺钉slotted knurled thumb screwswith collar46 DIN466 滚花高螺母knurled thumb nuts with collar GB806-8847 DIN467 滚花薄螺母knurled thumb thin nuts GB807-8848 DIN470 锁紧垫圈sealing washers49 DIN471 轴用弹性挡圈retaining rings forshafts(external),circlipsGB894.1-86 50 DIN472 孔用弹性挡圈retaining rings forbores(internal),circlipsGB893.1-8651 DIN478 方头带垫螺栓square head bolts with collar52 DIN479 方头圆柱底端螺栓square head bolts with half dogpoint53 DIN480方头带垫半圆底端螺栓square head bolts with collar,half dog point and rounded end54 DIN508 T型槽螺母T-slot nuts ISO29955 DIN525 单头螺柱single end studs56 DIN529 地脚螺栓masonry bolts GB799-8857 DIN546 带槽圆螺母slotted round nuts GB817-7658 DIN547 端面带孔圆螺母round nuts with drilled holes inone faceGB815-8859 DIN551 开槽平端紧定螺钉slotted sit screws with flat point I SO4776 GB73-8560 DIN553 开槽锥端紧定螺钉slotted set screws with conepointISO7434 GB71-8561 DIN555 六角螺母hexagon nuts ISO403462 DIN557 方螺母-C square nuts GB39-8863 DIN558 六角头螺钉hexagon screws ISO401864 DIN561六角头圆柱端紧定螺钉hexagon set screws with full dog point65 DIN562 薄型方螺母-Bsquare nuts withoutbevel(pressed nuts)66 DIN571 六角头木螺钉hexagon head wood screws(coach screws)GB102-8667 DIN580 吊环螺钉lifting eye bolts ISO3266 GB825-7668 DIN582 吊环螺母lifting eye nuts69 DIN601 六角头螺栓hexagon bolts ISO401670 DIN603大半圆头方颈螺栓(马车螺栓) mushroom head square neckbolts (carriage bolts)ISO8677 GB14-8871 DIN604沉头带插销马车螺栓flat countersunk nib bolts72 DIN605沉头长方颈马车螺栓flat countersunk long square neck bolts73 DIN607半圆头带插销马车螺栓cup head nib bolts74 DIN608沉头短方颈马车螺栓flat countersunk short square neck bolts75 DIN609六角头精配螺栓（长螺纹）hexagon fitted bolts,long thread76 DIN610六角头精配螺栓（短螺纹）hexagon fitted bolts,short thread77 DIN653 滚花平头螺钉knurled thumb screws thin type GB835-8878 DIN660 半圆头铆钉round head rivets ISO1051 GB867-8679 DIN661 沉头铆钉contersunk head rivets ISO1051 GB869-8680 DIN662 半沉头铆钉raised contersunk head rivets ISO105181 DIN674 大扁头铆钉mushroom head rivets ISO105182 DIN703重型侧面带孔圆螺母adjusting rings,heavy range (shafting collars)83 DIN705 侧面带孔圆螺母adjusting rings,light range(shafting collars)GB816-8884 DIN741 卡头wire rope clips85 DIN787 T型槽螺钉T-slot screws ISO29986 DIN835双头螺柱（牙长=2D）studs-metal (end=2d) GB900-8887 DIN906内六角锥型闭锁螺钉hexagon socket pipe plugs,conical thread88 DIN908内六角直型闭锁螺钉hexagon socket screw plugs,cyl. thread89 DIN909外六角锥型闭锁螺钉hexagon head pipe plugs,conical thread90 DIN910外六角直型闭锁螺钉hexagon head screw plugs,cyl.thread91 DIN911 内六角扳手socket wrenches ISO293692 DIN912 内六角圆柱头螺钉hexagon socket cap screws ISO4762 GB70-8593 DIN913内六角平端紧定螺钉hexagon socket set screws withflat pointISO4026 GB77-8594 DIN914内六角尖端紧定螺钉hexagon socket set screws withcone pointISO4027 GB78-8595 DIN915内六角圆柱端紧定螺钉hexagon socket set screws withdog pointISO4028 GB79-8596 DIN916 内六角凹端紧定螺hexagon socket set screws with ISO4029 GB80-85钉cup point97 DIN917 薄型盲螺母hexagon cap nuts98 DIN920 开槽小圆柱头螺钉slotted short cheese head screws99 DIN921 开槽大圆柱头螺钉slotted large cheese head screws GB838-88100 DIN923开槽圆柱头轴肩螺钉slotted pan head screws withshoulderGB830-88101 DIN927 开槽无头轴肩螺钉slotted shoulder screws102 DIN928 焊接方螺母square weld nuts GB/T13680-92 103 DIN929 焊接六角螺母hexagon weld nuts GB/T13681-92 104 DIN931 六角头螺栓（半牙）hexagon head screws ISO4014 GB5782-86 105 DIN933 六角头螺栓（全牙）hexagon head screws ISO4017 GB5783-86 106 DIN934 六角头螺母(1型) hexagon full nuts ISO4032 GB6170-86 107 DIN934细牙六角头螺母(1型)hexagon full nuts ISO8673 GB6171-86 108 DIN935 开槽六角螺母hexagon slotted and castle nuts ISO7035 GB6178-86 109 DIN936 六角头薄螺母hexagon thin nuts ISO4035 GB6172.1-86 110 DIN937 六角头开槽薄螺母hexagon thin slotted and castlenutsISO7038 GB6181-86 111 DIN938双头螺距（牙长=1D）studs metal (end=1d) GB897-88 112 DIN939双头螺距（牙长=1.25D）studs metal (end=1.25d) GB898-88 113 DIN940双头螺距（牙长=1.5D）studs metal (end=1.5d)114 DIN960六角头细牙螺栓（半牙）hexagon head bolts,metric finepitch threadISO8765 GB5785-86115 DIN961六角头细牙螺栓（全牙）hexagon head bolts,metric finepitch threadISO8676 GB5786-86116 DIN962头部穿孔六角头螺栓additional shapes and versions for bolts117 DIN963 开槽沉头螺钉slotted countersund head screws ISO 2009 GB68-85 118 DIN964 开槽半沉头螺钉slotted raised countersunk ovalhead screwsISO 2010 GB69-85 119 DIN965 十字槽沉头螺钉cross recessed countersunk headscrewsISO7046 GB819-85 120 DIN966 十字槽半沉头螺钉cross recessed raisedcountersunk head screwsISO7047 GB820-85 121 DIN970 六角头螺母hexagon nuts type-1122 DIN971 六角头螺母hexagon nuts type-2123 DIN972细牙六角头螺母(2型)hexagon nuts with fine thread ISO8674 GB6176-86 124 DIN975 牙条(全螺纹) threaded rods(studdings) GB15389-94 125 DIN976 螺纹销threaded pins(stud bolts)126 DIN979六角头开槽薄螺母（2型）hexagon thin slotted and castle nuts127 DIN980全金属六角锁紧螺母（1型）prevailling torque type hexagonnuts,all metall nutsISO7199 GB6184-86128 DIN981 圆螺母locknuts ISO2982 GB812-88129 DIN982六角头尼龙锁紧螺母prevailling torque type hexagonnuts,heavy type ,with nyloninsertISO7040 GB889.1-86130 DIN985六角头薄型尼龙锁紧螺母prevailling torque type hexagonnuts,heavy type ,with nyloninsertISO10511 GB6172.2-86131 DIN986六角盖型尼龙锁紧螺母prevailling torque typedomed capnuts with nylon insert132 DIN988 配合垫片shim rings133 DIN1052 木材连接用垫片washers for timber connectors134 DIN1151 沉头钢钉round plain head nails135 DIN1440 销钉专用垫片A型plain washers for clevis pins(A型)ISO8738136 DIN1441 销钉专用垫片plain washers for clevis pins137 DIN1444 带头销钉clevis pins with head ISO2341138 DIN1471 圆锥型槽销grooved pins,taper grooved ISO8744 GB/T13829.2 139 DIN1472 圆锥型槽销(半槽)grooved pins,taper grooved halflengthISO8745 GB/T13829.2 140 DIN1473 平行槽销(带倒角)grooved pins,parallel groovedfull lengthISO8740141 DIN1474 前端凹槽槽销grooved pins,reserve groovedhalf lengthISO8741142 DIN1475 中部凹槽槽销grooved pins,centre grooved ISO8742143 DIN1476 圆头槽销grooved pins with round head ISO8746 GB/T13829.3 144 DIN1477 沉头槽销grooved pins with countersunkheadISO8747145 DIN1479 六角螺母棒turnuckles(centre parts),madeout of hexagon bar146 DIN1480 花篮螺栓turnuckles with eye bolt andhook bolt147 DIN1481 弹性圆柱销spring pins,heavy type ISO8752 GB879-86 148 DIN1587 组合式盖型螺母hexagon domed cap nuts GB802-88149 DIN1804开槽圆螺母（配合沟头扳手）slotted round nuts for hook spanner150 DIN1816 圆螺母（带插销孔）round nuts with set holes 151 DIN2093 盘型弹簧垫圈disc springs152 DIN3017 喉箍hose clamps153 DIN3404 润滑油嘴（旋扭头）lubricating nipples,button head154 DIN3567 管夹shackles for conduilts155 DIN3570 U型螺栓stirrup bolts(U-bolts)156 DIN6319 球面垫圈spherical washers,conical seats GB849-88 157 DIN6325 圆柱销parallel pins ISO8734158 DIN6330 厚六角螺母hexagon nuts ,1.5d GB56-88 159 DIN6331 厚六角法兰面螺母hexagon nuts ,1.5d with collar GB6177-86 160 DIN6334 长六角螺母hexagon nuts ,3d161 DIN6797-A 外齿锁紧垫圈external teeth lock washers GB862.1-87 162 DIN6797-I 内齿锁紧垫圈internal teeth lock washers GB861.1-87 163 DIN6798-A 外锯齿锁紧垫圈external teeth serrated lockwashersGB862.2-87 164 DIN6798-I 内锯齿锁紧垫圈internal teeth serrated lockwashersGB861.2-87 165 DIN6799 开口挡圈retaining rings forshafts(E-rings),circlipsGB896-76 166 DIN6885 平键（A型）parallel keys(form A ) ISO773/2491167 DIN6888 半圆键woodruff keys ISO3912168 DIN6899 嵌环（支撑环）thimbles169 DIN6900机器螺钉和垫圈组合件screws and washers assemblies GB9074.1-.17170 DIN6901自攻螺钉和垫圈组合件tapping screws and washersassembliesGB9074.18-.23171 DIN6912薄型带孔内六角圆柱头螺钉hexagon socket head cap screws with hole,low head172 DIN6914 大六角头螺栓hexagon head bolts with largehead(friction grip bolts)173 DIN6915 大六角螺母hexagon nuts with large widethacross flat(friction grip nuts)174 DIN6916 大垫圈round washers for friction gripbolts175 DIN6917 楔型方垫圈spuare taper washers for frictiongrip bolts on T-sections176 DIN6923 六角法兰面螺母hexagon flange nuts ISO4161 GB6177-86177 DIN6925全金属六角锁紧螺母(2型）prevailing torque type hexagonnuts,all metallic nutsISO7042 GB6185.1-2000178 DIN7337开口型抽芯铆钉（沉头、扁圆头）blind rivets GB12617/12618 179 DIN7338扁平头半空心/全空心铆钉rivets for brake and clutch lining GB875/975-86 180 DIN7343 螺旋夹紧销spiral pins ISO8750181 DIN7346 轻型弹性圆柱销spring pins,light type ISO13337182 DIN7349重型弹性圆柱销用垫圈washers for bolts with heavy type spring pinss183 DIN7500ISO公制螺纹螺钉(多种头型) threadforming screws for ISO-metric thread184 DIN7504自攻自钻螺钉(多种头型)self-drilling tapping screws 185 DIN7513开槽切削螺纹螺钉(多种头型)thread cutting screws186 DIN7516十字槽切削螺纹螺钉(多种头型) thread cutting screws cross recess187 DIN7965 T型四爪螺母tee nuts with pronge188 DIN7968钢结构用六角头螺栓连接副hexagon head fitted bolts forsteel structuresGB1228/1229/1230189 DIN7971 开槽盘头自攻螺钉pan head tapping screws withslotISO1481 GB5282-85 190 DIN7972 开槽沉头自攻螺钉countersunk flat head tappingscrews with slotISO1482 GB5283-85191 DIN7973开槽半沉头自攻螺钉raised countersunk oval headtapping screws with slotISO1483 GB5284-85192 DIN7976 六角头自攻螺钉hexagon tapping screws ISO1479 GB5285-85193 DIN7980圆柱头螺钉用弹簧垫圈spring lock washers for screwswith cylindrical headsISO8738194 DIN7981十字槽盘头自攻螺钉pan head tapping screws withcross recessedISO 7049 GB845-85195 DIN7982十字槽沉头自攻螺钉countersunk flat head tappingscrews with cross recessedISO7050 GB846-85196 DIN7983十字槽半沉头自攻螺钉raised countersunk oval headtapping screws with crossrecessedISO7051 GB847-86197 DIN7984薄型内六角圆柱头螺钉hexagon socket head cap screws with，reduced head198 DIN7985 十字槽盘头螺钉pan head screws with crossrecessedISO7045 GB818-85 199 DIN7989 钢结构用垫圈washers for steel structures GB1230-84200 DIN7990钢结构用六角头螺栓hexagon head bolts for steelstructuresGB1229-84201 DIN7991 内六角沉头螺钉hexagon socket countersunkhead screwsISO10642202 DIN7993 轴用钢丝挡圈roundwire snap rings for shafts GB895.2-86203 DIN7995十字槽半沉头木螺钉cross recessed raisedcountersunk head wood screwsGB952-86204 DIN7996 十字槽圆头木螺钉cross recessed round head woodscrewsGB950-86 205 DIN7997 十字槽沉头木螺钉cross recessed countersunk headwood screwsGB951-86206 DIN8140螺纹护套（普通\自锁等）ciol inserts,coarse,fine thread,silf locking207 DIN9021 大外径垫圈washers,outside diameterappro.3dISO7093 GB96-85 208 DIN11024 弹簧卡子spring cotter for a bolt209 DIN13257 平板螺栓belting bolts (elevator bolts)210 DIN18182 干壁钉（墙板钉）dry wall screws211 DIN28129 环型螺母lifting nuts(eye nuts) GB63-88 212 DIN70952 圆螺母用止退垫圈tab washers for slotted roundnutsGB858-88。

德标、欧标、国际、国标对照表—— DIN EN ISO GB 对照表新德标旧德标 英文名 中文名 国标 DIN EN ISO 4014 DIN 931-1 Hexagon head bolts - Product grades A and B(ISO 4014:1999) 六角头螺栓 GB/T 5782-2000 DIN EN ISO 4016DIN 601 Hexagon head bolts - Product grade C(ISO 4016:1999) 六角头螺栓 C 级 GB/T 5780-2000 DIN EN ISO 4017DIN 933 Hexagon head screws - Product grade A and B (ISO 4017:1999) 六角头螺栓 全螺纹 GB/T 5783-2000 DIN EN ISO 4018DIN 558 Hexagon head screws - Product grade C (ISO 4018:1999) 六角头螺栓 全螺纹 C 级 GB/T 5781-2000 DIN EN ISO 8676DIN 961 Hexagon head screws with metric fine pitch thread - Product grade A and B(ISO 8676:1999) 六角头螺栓 细牙 全螺纹 GB/T 5786-2000 DIN EN ISO 8765DIN 960 Hexagon head bolts with fine pitch thread - Product grades A and B(ISO 8765:1999) 六角头螺栓 细牙 GB/T 5785-2000 DIN EN ISO 4032DIN 934 Hexagon nuts,style 1-Product grades A and B(ISO: 4032:1999) 1型六角螺母 GB/T 6170-2000 DIN EN ISO 4033Hexagon nuts,style 2-Product grades A and B(ISO: 4033:1999) 2型六角螺母 GB/T 6175-2000 DIN EN ISO 4034DIN 555 Hexagon nuts - Product grade C (ISO 4034:1999) 六角螺母 C 级 GB/T 41-2000 DIN EN ISO 4035DIN 439-2 Hexagon thin nuts(chamfered)-Product grade A and B (ISO 4035:1999) 六角薄螺母 GB/T 6172.1-2000 DIN EN ISO 4036DIN 439-1 Hexagon thin nuts - Product grade B(unchamfered)(ISO 4036:1999) 六角薄螺母 无倒角 GB/T 6174-2000 DIN EN ISO 8673DIN 934| DIN 971-1 Hexagon nuts,style 1,with metric fine pitch thread - Product grades A and B (ISO 8673:1999) 1型六角螺母 细牙 GB/T 6171-2000 DIN EN ISO 8674DIN 971-2 Hexagon nuts,style 2,with metric fine pitch thread - Product grades A and B (ISO 8674:1999) 2型六角螺母 细牙 GB/T 6176-2000 DIN EN ISO 8675DIN 439-2 Hexagon thin nuts with metric fine pitch thread - Product grades A and B (ISO 8675:1999) 六角薄螺母 细牙 GB/T 6173-2000 DIN EN ISO 4762DIN 912 Hexagon socket head cap screws(ISO 4762:1997) 内六角圆柱头螺钉 GB/T 70.1-2000 DIN EN ISO 7380Hexagon socket button head sxrews (ISO 7380:1997) 内六角平圆头螺钉 GB/T 70.2-2000 DIN EN ISO 10642DIN 7991 Hexagon socket countersunk head screws (ISO 10642:1997) 内六角沉头螺钉 GB/T 70.3-2000 DIN EN ISO 1207 DIN 84 Slotted cheese head screws-Product grade A(ISO 1207:1992) 开槽圆柱头螺钉GB/T 65-2000DIN EN ISO 1580DIN 85 Slotted pan head screws-Product grade A(ISO 1580:1994) 开槽盘头螺钉 GB/T 67-2000 DIN EN ISO 2009DIN 963 Slotted countersunk flat head screws(common head style)(ISO 2009:1994) 开槽沉头螺钉 GB/T 68-2000 DIN EN ISO 2010DIN 964 Countersunk slotted raised head screws(common head style)-Produce grade A(ISO 2010:1994) 开槽半沉头螺钉 GB/T 69-2000 DIN EN ISO 7045DIN 7985 Pan head screws with type H or type Z cross recess-Product grade A(ISO 7054:1994) 十字槽盘头螺钉 GB/T 818-2000 DIN EN ISO 7046-1DIN 965 Countersunk flat head screws (common head style)with type H or type Z cross recess,product grade A-Part 1:Steel of property class 4.8(ISO 7046-1:1994) 十字槽盘头螺钉 第1部分：钢4.8级 GB/T 819.1-2000 DIN EN ISO 7046-2DIN 965 Cross recessed countersunk flat head screws (common head style),product grade A-Part2:Steel of property class 8.8,stainless steel and nonferous metals(ISO 7046-2:1990) 十字槽沉头螺钉 第2部分：钢8.8、不锈钢A2-70和有色金属CU2或CU3 GB/T 819.2-1997 DIN EN ISO 7047DIN 966 Countersunk raised head screws (common head style) with type H or type Z cross recess-Product grade A(ISO 7047:1994) 十字槽半沉头螺钉 GB/T 820-2000 DIN EN ISO 7048Cross recessed cheese head screws (ISO 7048:1998) 十字槽圆柱头螺钉 GB/T 822-2000 DIN EN ISO 10644Screw and washer assemblies with plain washers-Washer hardness classes 200HV and 300HV(ISO 10644:1998) 螺栓或螺钉和平垫圈组合件 GB/T 9074.1-2002 DIN EN ISO 10510Tapping screw and washer assemblies with plain washers(ISO 10510l:1999) 自攻螺钉和平垫圈组合件 GB/T 9074.18-2002 IDN EN ISO 15480Hexagon washer head drilling screws with tapping screws thread (ISO 15480:1999) 六角凸缘自钻自攻螺钉 GB/T 15856.5-2002 IDN EN ISO 15481Cross recessed pan head drilling screws with tapping screw thread(ISO 15481:1999) 十字槽盘头自钻自攻螺钉 GB/T 15856.1-2002 IDN EN ISO 15482Cross recessed countersunk head drilling screws with tapping screw thread (ISO 15482:1999) 十字槽沉头自钻自攻螺钉 GB/T 15856.2-2002 IDN EN ISO 15483 Cross recessed raised countersunk head drilling screws with tapping screw thread(ISO 15483:1999) 十字槽半沉头自钻自攻螺钉GB/T 15856.3-2002DIN EN ISO 10669Plain washers for tapping screw and washer assemblies - Normal and large series - Product grade A （ISO 10669:1999) 平垫圈 用于自攻螺钉和垫圈组合件 GB/T 97.5-2002 DIN EN ISO 10673Plain washers for screw and washer assemblies - Small,normal and large series - Product grade A (ISO 10673:1998) 平垫圈 用于螺钉和垫圈组合件 GB/T 97.4-2002 DIN EN ISO 2338DIN 7 Parallel pins,of unhardened steel and austenitic stainless steel(ISO 2338:1997) 圆柱销 不淬硬钢和奥氏体不锈钢 GB/T 119.1-2000 DIN EN ISO 8733DIN 7979 Parallel pins whit internal thread,of unhardened steel and austenitic stainless steel(ISO 8733:1997) 内螺纹圆柱销 不淬硬钢和奥氏体不锈钢 GB/T 120.1-2000 DIN EN ISO 8734DIN 6325 Parallel pins,of hardened steel or martensitic stainless steel(Dowel pins)(ISO 8734:1997) 圆柱销 淬硬钢和马氏体不锈钢 GB/T 119.2-2000 DIN EN ISO 8735DIN 7979 Parallel pins with internal thread,of hardened steel and martensitic stainless steel(ISO 8735:1997) 内螺纹圆柱销 淬硬钢和马氏体不锈钢 GB/T 120.2-2000 DIN EN ISO 8748DIN 7344 Spring-type straight pins,coiled,heavy duty (ISO 8748:1997) 弹性圆柱销 卷制 重型 GB/T 879.3-2000 DIN EN ISO 8750DIN 7343 Spring-type straight pins,coiled,standard duty (ISO 8750:1997) 弹性圆柱销 卷制 标准型 GB/T 879.4-2000 DIN EN ISO 8751Spring-type straight pins,coiled,light duty （ISO 8751:1997) 弹性圆柱销 卷制 轻型 GB/T 879.5-2000 DIN EN ISO 8752DIN 1481 Spring-type straight pins,slotted,heavy duty (ISO 8752:1997) 弹性圆柱销 直槽 重型 GB/T 879.1-2000 DIN EN ISO 13337DIN 7346 Spring-type straight pins,slotted,light duty (ISO 13337:1997) 弹性圆柱销 直槽 轻型 GB/T 879.2-2000 DIN EN ISO 1234DIN 94 Split pins （ISO1234:1997) 开口销 GB/T 91-2000 DIN EN ISO 7089Plain washers-Normal series-Product grade A 平垫圈 A 级 GB/T 97.1-2002 DIN EN ISO 7090Plain washers,chamfered-Normal series-Product grade A(ISO 7090:2000) 平垫圈 倒角型 A 级 GB/T 97.2-2002 DIN EN ISO 7091Plain washers-Normal series-Product grade C(ISO 7091:2000) 平垫圈 C 级 GB/T 95-2002 DIN EN ISO 7092Plain washers-Small series-Product grade A(ISO 7092:2000) 小垫圈 A 级 GB/T 848-2002 DIN EN ISO 7093-1 Plain washers-Large series-Part 1: Product grade A(ISO 70931-1:2000)大垫圈 A 级 GB/T 96.1-2002DIN EN ISO 7093-2 Plain washers-Normal series-Part 3: Product grade C(ISO 70936-2:2000)大垫圈 C 级 GB/T 96.2-2002DIN EN ISO 7094 Plain washers-Extra large series -Product grade C(ISO 7094:2000) 特大垫圈 C 级GB/T 5287-2002DIN EN ISO 7040 DIN 982| DIN 6924 Prevailing torque type hexagon nuts (with non-metallic insert),style 1 - Property classes 5,8 and 10(ISO 7040:1997)1型非金属嵌件六角锁紧螺母GB/T 889.1-2000DIN EN ISO 7042 DIN 980| DIN 6925 Prevailing torque type all-metalhexagon nuts,style 2 - Propertyclasses 5,8, 10 and 12(ISO7042:1997)2型全金属六角锁紧螺母 GB/T 6185.1-2000 DIN EN ISO 7719 Prevailing torque type all-metalhexagon nuts,style 1- Propertyclasses 5,8 and 10(ISO 7719:1997) 1型全金属六角锁紧螺母GB/T 6184-2000 DIN EN ISO 10511 DIN 985 Prevailing torque type hexagon thin nuts (with non-metallic insert )(ISO 10511:1997) 非金属嵌件六角锁紧薄螺母 GB/T 6072.2-2000DIN EN ISO 10512 DIN 982|DIN 6924Prevailing torque type hexagon nuts (with non-metallic insert),style 1,with metric fine pitch thread-Property classes 6,8 and 10(ISO 10512:1997) 1型非金属嵌件六角锁紧螺母 细牙 GB/T 889.2-2000 DIN EN ISO 10513 DIN 980|DIN 6925 Prevailing torque type all-metal hexagon nuts,style 2,with metric fine pitch thread - Property classes 8,10 and 12(ISO 10513:1997) 2型全金属六角锁紧螺母 细牙GB/T 6185.2-2000原汁原味的德标 DIN (ISO 、EN)、美标 IFI (ANSI, ASME, SAE)、公制美标、日标 JIS 资料！ 在螺纹紧固件的使用中应用的较广泛的是螺栓－螺母连接副的形式，应用的较多的是有预紧力的连接方式，预紧力的连接可以提高螺栓连接的可靠性、防松能力及螺栓的疲劳强度，并且能增强螺纹连接体的紧密性和刚度。

din标准与国标对照表标准是按照一定的规则和程序确立的、共同认可的规范或指导原则。

在不同国家和不同领域，都有各种各样的标准。

由于不同地区存在差异，不同国家制定的标准也各不相同。

而对照表是将两个或多个标准进行比对，以便理解它们之间的异同和相互关系。

DIN标准又称为德国标准，是德国国家标准机构制定的一系列技术和工程标准。

DIN标准在德国和许多其他国家中得到广泛应用。

而国标是指中国国家标准，由中国国家标准化管理委员会制定和发布的一系列标准。

下面是一些DIN标准与国标之间的对照：2.DIN476与GB/T1-1997对照表：这是关于纸张尺寸的标准。

DIN476是德国标准，GB/T1-1997是中国国家标准。

对照表可以帮助人们了解这两个标准中不同纸张尺寸的对应关系。

3.DIN912与GB/T70.1-2024对照表：这是关于螺栓连接的标准。

DIN912是德国标准，GB/T70.1-2024是中国国家标准。

对照表可以帮助人们了解这两个标准中对螺栓连接要求的差异。

通过对照表的比较，可以帮助人们更好地理解和应用不同国家的标准。

在全球化的背景下，了解和比较国内外的标准对于企业进行国际合作、进口和出口以及在全球市场上竞争至关重要。

对照表还可以帮助企业合理制定产品和服务的质量要求，确保他们符合国内和国际的标准要求。

然而，不同国家的标准虽然在一些方面有相似之处，但也存在很多差异。

这些差异可能是由技术水平、法律法规、文化差异以及市场需求等因素导致的。

因此，在对照表中，可能需要考虑一些因素，如标准制定背景、适用范围和标准解释等。

此外，不同国家的标准可能会进行更新和修订，所以在使用对照表时需要留意标准的最新版本。

总之，对照表是比较不同国家标准之间的异同的有用工具。

它可以帮助人们了解和应用不同国家的标准，促进国际交流和合作。

不管是企业、行业协会还是标准制定机构，都可以利用对照表来提高他们的标准化工作水平，推动标准化的国际化发展。

德国标准和国际标准、中国标准中英文对照表序号德国标准中文品名英文品名国际标准中国标准Description inItem D IN-StandardDescription in English ISO-Standard GB-Standard Chinese1 DIN1 圆锥销taper pins ISO2339 GB1172 DIN7 圆柱销parallel pins ISO2338 GB119-863 DIN84 开槽圆柱头螺钉slotted cheese head screws ISO1207 GB65-854 DIN85 开槽盘头螺钉slotted pan head screws ISO1580 GB67-855 DIN93 单耳止动垫圈tab washers GB8546 DIN94 开口销split cotter pins ISO1234 GB91slotted raised csk head wood7 DIN95 开槽半沉头木螺钉GB101screws8 DIN96 开槽半圆头木螺钉slotted round head wood screws GB99slotted countersunk head wood9 DIN97 开槽沉头木螺钉GB100screws10 DIN125-A 平垫plain washers ISO7089 GB97.1-8511 DIN125-B 平垫(带倒角) mediun washers ISO7090 GB97.2-8512 DIN126 平垫plain washers ISO709113 DIN127-A 重型弹垫spring lock washers,tang ends GB724414 DIN127-B 标准弹垫spring lock washers,square ends GB93-8715 DIN128-A 鞍形弹垫single coil spring lock washers GB7245-8716 DIN137-A 弹簧止动垫圈curved spring washers17 DIN137-B 波形弹垫wave spring washers GB95518 DIN186 T型方颈螺栓T-head bolts with square neck GB 37-8819 DIN188 T型双接头螺栓T-head bolts with double nip20 DIN258 螺纹圆锥销taper pins with threaded end ISO873721 DIN261 T型头螺栓T-head bolts22 DIN315AF 蝶型螺母(美制) wing nuts amercia form23 DIN315DF 蝶型螺母(德制) wing nuts germany form GB62-8824 DIN316AF 蝶型螺钉(美制) wing screws amercia form25 DIN317DF 蝶型螺钉(德制) wing screws germany form26 DIN319 圆球型盖型螺母ball knobs27 DIN404开槽带孔球面圆柱头螺钉slotted capstan screws GB832-8828 DIN417开槽长圆柱端紧定螺钉slotted set srews with full dogpointISO7435 GB75-8529 DIN427开槽平端紧定螺钉(半牙) slotted set srews with chamferedendISO2342 GB73-8530 DIN431小六角特薄细牙螺母pipe nuts with thread GB808-8831 DIN432 外舌止动垫圈external tap GB856-8832 DIN433小垫圈(用于圆柱头螺钉)washers for cheese head screws ISO7092 GB848-95 33 DIN434 方斜垫圈(U型)square taper washers forU-sectionGB852-88 34 DIN435 方斜垫圈(I型)square taper washers forI-sectionsGB852-8835 DIN436 方垫圈square washers36 DIN438 开槽凹端紧定螺钉slotted set with cup point ISO7436 GB74-8537 DIN439 六角薄螺母hexagon thin nuts ISO4035 GB6172-8638 DIN439 细牙六角薄螺母hexagon thin nuts ISO8675 GB6173-8639 DIN440 木螺钉专用垫圈rounds washers for woodconstructionsISO709440 DIN443 密封帽sealing caps,push-in type41 DIN444 活节螺栓B 型eye bolts form B GB798-8842 DIN462 内舌止动垫圈internal tab washers43 DIN463 双耳止动垫圈washers with two taps GB855-8844 DIN464 滚花高头螺钉knurled thumb screws withcollarGB834-88 45 DIN465 开槽滚花高头螺钉slotted knurled thumb screwswith collar46 DIN466 滚花高螺母knurled thumb nuts with collar GB806-8847 DIN467 滚花薄螺母knurled thumb thin nuts GB807-8848 DIN470 锁紧垫圈sealing washers49 DIN471 轴用弹性挡圈retaining rings forshafts(external),circlipsGB894.1-86 50 DIN472 孔用弹性挡圈retaining rings forbores(internal),circlipsGB893.1-8651 DIN478 方头带垫螺栓square head bolts with collar52 DIN479 方头圆柱底端螺栓square head bolts with half dogpoint53 DIN480方头带垫半圆底端螺栓square head bolts with collar,half dog point and rounded end54 DIN508 T型槽螺母T-slot nuts ISO29955 DIN525 单头螺柱single end studs56 DIN529 地脚螺栓masonry bolts GB799-8857 DIN546 带槽圆螺母slotted round nuts GB817-7658 DIN547 端面带孔圆螺母round nuts with drilled holes inone faceGB815-8859 DIN551 开槽平端紧定螺钉slotted sit screws with flat point I SO4776 GB73-8560 DIN553 开槽锥端紧定螺钉slotted set screws with conepointISO7434 GB71-85 61 DIN555 六角螺母hexagon nuts ISO403462 DIN557 方螺母-C square nuts GB39-8863 DIN558 六角头螺钉hexagon screws ISO401864 DIN561六角头圆柱端紧定螺钉hexagon set screws with full dog point65 DIN562 薄型方螺母-Bsquare nuts withoutbevel(pressed nuts)66 DIN571 六角头木螺钉hexagon head wood screws(coach screws)GB102-8667 DIN580 吊环螺钉lifting eye bolts ISO3266 GB825-7668 DIN582 吊环螺母lifting eye nuts69 DIN601 六角头螺栓hexagon bolts ISO401670 DIN603大半圆头方颈螺栓(马车螺栓) mushroom head square neckbolts (carriage bolts)ISO8677 GB14-8871 DIN604沉头带插销马车螺栓flat countersunk nib bolts72 DIN605沉头长方颈马车螺栓flat countersunk long square neck bolts73 DIN607半圆头带插销马车螺栓cup head nib bolts74 DIN608沉头短方颈马车螺栓flat countersunk short square neck bolts75 DIN609六角头精配螺栓（长螺纹）hexagon fitted bolts,long thread76 DIN610六角头精配螺栓（短螺纹）hexagon fitted bolts,short thread77 DIN653 滚花平头螺钉knurled thumb screws thin type GB835-8878 DIN660 半圆头铆钉round head rivets ISO1051 GB867-8679 DIN661 沉头铆钉contersunk head rivets ISO1051 GB869-8680 DIN662 半沉头铆钉raised contersunk head rivets ISO105181 DIN674 大扁头铆钉mushroom head rivets ISO105182 DIN703重型侧面带孔圆螺母adjusting rings,heavy range (shafting collars)83 DIN705 侧面带孔圆螺母adjusting rings,light range(shafting collars)GB816-8884 DIN741 卡头wire rope clips85 DIN787 T型槽螺钉T-slot screws ISO29986 DIN835双头螺柱（牙长=2D）studs-metal (end=2d) GB900-8887 DIN906内六角锥型闭锁螺钉hexagon socket pipe plugs,conical thread88 DIN908内六角直型闭锁螺钉hexagon socket screw plugs,cyl. thread89 DIN909外六角锥型闭锁螺钉hexagon head pipe plugs,conical thread90 DIN910外六角直型闭锁螺钉hexagon head screw plugs,cyl.thread91 DIN911 内六角扳手socket wrenches ISO293692 DIN912 内六角圆柱头螺钉hexagon socket cap screws ISO4762 GB70-8593 DIN913内六角平端紧定螺钉hexagon socket set screws withflat pointISO4026 GB77-8594 DIN914内六角尖端紧定螺钉hexagon socket set screws withcone pointISO4027 GB78-8595 DIN915内六角圆柱端紧定螺钉hexagon socket set screws withdog pointISO4028 GB79-8596 DIN916内六角凹端紧定螺钉hexagon socket set screws withcup pointISO4029 GB80-8597 DIN917 薄型盲螺母hexagon cap nuts98 DIN920 开槽小圆柱头螺钉slotted short cheese head screws99 DIN921 开槽大圆柱头螺钉slotted large cheese head screws GB838-88100 DIN923开槽圆柱头轴肩螺钉slotted pan head screws withshoulderGB830-88101 DIN927 开槽无头轴肩螺钉slotted shoulder screws102 DIN928 焊接方螺母square weld nuts GB/T13680-92 103 DIN929 焊接六角螺母hexagon weld nuts GB/T13681-92 104 DIN931 六角头螺栓（半牙）hexagon head screws ISO4014 GB5782-86 105 DIN933 六角头螺栓（全牙）hexagon head screws ISO4017 GB5783-86 106 DIN934 六角头螺母(1型) hexagon full nuts ISO4032 GB6170-86 107 DIN934细牙六角头螺母(1型)hexagon full nuts ISO8673 GB6171-86 108 DIN935 开槽六角螺母hexagon slotted and castle nuts ISO7035 GB6178-86 109 DIN936 六角头薄螺母hexagon thin nuts ISO4035 GB6172.1-86 110 DIN937 六角头开槽薄螺母hexagon thin slotted and castlenutsISO7038 GB6181-86 111 DIN938双头螺距（牙长=1D）studs metal (end=1d) GB897-88 112 DIN939双头螺距（牙长=1.25D）studs metal (end=1.25d) GB898-88 113 DIN940双头螺距（牙长=1.5D）studs metal (end=1.5d)114 DIN960六角头细牙螺栓（半牙）hexagon head bolts,metric finepitch threadISO8765 GB5785-86115 DIN961六角头细牙螺栓（全牙）hexagon head bolts,metric finepitch threadISO8676 GB5786-86116 DIN962 头部穿孔六角头螺additional shapes and versions栓for bolts117 DIN963 开槽沉头螺钉slotted countersund head screws ISO 2009 GB68-85 118 DIN964 开槽半沉头螺钉slotted raised countersunk ovalhead screwsISO 2019 GB69-85 119 DIN965 十字槽沉头螺钉cross recessed countersunk headscrewsISO7046 GB819-85 120 DIN966 十字槽半沉头螺钉cross recessed raisedcountersunk head screwsISO7047 GB820-85 121 DIN970 六角头螺母hexagon nuts type-1122 DIN971 六角头螺母hexagon nuts type-2123 DIN972细牙六角头螺母(2型)hexagon nuts with fine thread ISO8674 GB6176-86 124 DIN975 牙条(全螺纹) threaded rods(studdings) GB15389-94 125 DIN976 螺纹销threaded pins(stud bolts)126 DIN979六角头开槽薄螺母（2型）hexagon thin slotted and castle nuts127 DIN980全金属六角锁紧螺母（1型）prevailling torque type hexagonnuts,all metall nutsISO7199 GB6184-86128 DIN981 圆螺母locknuts ISO2982 GB812-88129 DIN982六角头尼龙锁紧螺母prevailling torque type hexagonnuts,heavy type ,with nyloninsertISO7040 GB889.1-86130 DIN985六角头薄型尼龙锁紧螺母prevailling torque type hexagonnuts,heavy type ,with nyloninsertISO10511 GB6172.2-86131 DIN986六角盖型尼龙锁紧螺母prevailling torque typedomed capnuts with nylon insert132 DIN988 配合垫片shim rings133 DIN1052 木材连接用垫片washers for timber connectors134 DIN1151 沉头钢钉round plain head nails135 DIN1440 销钉专用垫片A型plain washers for clevis pins(A型)ISO8738136 DIN1441 销钉专用垫片plain washers for clevis pins137 DIN1444 带头销钉clevis pins with head ISO2341138 DIN1471 圆锥型槽销grooved pins,taper grooved ISO8744 GB/T13829.2 139 DIN1472 圆锥型槽销(半槽)grooved pins,taper grooved halflengthISO8745 GB/T13829.2 140 DIN1473 平行槽销(带倒角)grooved pins,parallel groovedfull lengthISO8740141 DIN1474 前端凹槽槽销grooved pins,reserve groovedhalf lengthISO8741142 DIN1475 中部凹槽槽销grooved pins,centre grooved ISO8742143 DIN1476 圆头槽销grooved pins with round head ISO8746 GB/T13829.3 144 DIN1477 沉头槽销grooved pins with countersunkheadISO8747145 DIN1479 六角螺母棒turnuckles(centre parts),madeout of hexagon bar146 DIN1480 花篮螺栓turnuckles with eye bolt andhook bolt147 DIN1481 弹性圆柱销spring pins,heavy type ISO8752 GB879-86 148 DIN1587 组合式盖型螺母hexagon domed cap nuts GB802-88149 DIN1804开槽圆螺母（配合沟头扳手）slotted round nuts for hook spanner150 DIN1816 圆螺母（带插销孔）round nuts with set holes 151 DIN2093 盘型弹簧垫圈disc springs152 DIN3017 喉箍hose clamps153 DIN3404 润滑油嘴（旋扭头）lubricating nipples,button head154 DIN3567 管夹shackles for conduilts155 DIN3570 U型螺栓stirrup bolts(U-bolts)156 DIN6319 球面垫圈spherical washers,conical seats GB849-88 157 DIN6325 圆柱销parallel pins ISO8734158 DIN6330 厚六角螺母hexagon nuts ,1.5d GB56-88 159 DIN6331 厚六角法兰面螺母hexagon nuts ,1.5d with collar GB6177-86 160 DIN6334 长六角螺母hexagon nuts ,3d161 DIN6797-A 外齿锁紧垫圈external teeth lock washers GB862.1-87 162 DIN6797-I 内齿锁紧垫圈internal teeth lock washers GB861.1-87 163 DIN6798-A 外锯齿锁紧垫圈external teeth serrated lockwashersGB862.2-87 164 DIN6798-I 内锯齿锁紧垫圈internal teeth serrated lockwashersGB861.2-87 165 DIN6799 开口挡圈retaining rings forshafts(E-rings),circlipsGB896-76 166 DIN6885 平键（A型）parallel keys(form A ) ISO773/2491167 DIN6888 半圆键woodruff keys ISO3912168 DIN6899 嵌环（支撑环）thimbles169 DIN6900机器螺钉和垫圈组合件screws and washers assemblies GB9074.1-.17170 DIN6901自攻螺钉和垫圈组合件tapping screws and washersassembliesGB9074.18-.23171 DIN6912薄型带孔内六角圆柱头螺钉hexagon socket head cap screws with hole,low head172 DIN6914 大六角头螺栓hexagon head bolts with largehead(friction grip bolts)173 DIN6915 大六角螺母hexagon nuts with large widethacross flat(friction grip nuts)174 DIN6916 大垫圈round washers for friction gripbolts175 DIN6917 楔型方垫圈spuare taper washers for frictiongrip bolts on T-sections176 DIN6923 六角法兰面螺母hexagon flange nuts ISO4161 GB6177-86177 DIN6925全金属六角锁紧螺母(2型）prevailing torque type hexagonnuts,all metallic nutsISO7042 GB6185.1-2000178 DIN7337开口型抽芯铆钉（沉头、扁圆头）blind rivets GB12617/12618 179 DIN7338扁平头半空心/全空心铆钉rivets for brake and clutch lining GB875/975-86 180 DIN7343 螺旋夹紧销spiral pins ISO8750181 DIN7346 轻型弹性圆柱销spring pins,light type ISO13337182 DIN7349重型弹性圆柱销用垫圈washers for bolts with heavy type spring pinss183 DIN7500ISO公制螺纹螺钉(多种头型) threadforming screws for ISO-metric thread184 DIN7504自攻自钻螺钉(多种头型)self-drilling tapping screws 185 DIN7513开槽切削螺纹螺钉(多种头型)thread cutting screws186 DIN7516十字槽切削螺纹螺钉(多种头型) thread cutting screws cross recess187 DIN7965 T型四爪螺母tee nuts with pronge188 DIN7968钢结构用六角头螺栓连接副hexagon head fitted bolts forsteel structuresGB1228/1229/1230189 DIN7971 开槽盘头自攻螺钉pan head tapping screws with ISO1481 GB5282-85190 DIN7972 开槽沉头自攻螺钉countersunk flat head tappingscrews with slotISO1482 GB5283-85191 DIN7973开槽半沉头自攻螺钉raised countersunk oval headtapping screws with slotISO1483 GB5284-85192 DIN7976 六角头自攻螺钉hexagon tapping screws ISO1479 GB5285-85193 DIN7980圆柱头螺钉用弹簧垫圈spring lock washers for screwswith cylindrical headsISO8738194 DIN7981十字槽盘头自攻螺钉pan head tapping screws withcross recessedISO 7049 GB845-85195 DIN7982十字槽沉头自攻螺钉countersunk flat head tappingscrews with cross recessedISO7050 GB846-85196 DIN7983十字槽半沉头自攻螺钉raised countersunk oval headtapping screws with crossrecessedISO7051 GB847-86197 DIN7984薄型内六角圆柱头螺钉hexagon socket head cap screws with，reduced head198 DIN7985 十字槽盘头螺钉pan head screws with crossrecessedISO7045 GB818-85 199 DIN7989 钢结构用垫圈washers for steel structures GB1230-84200 DIN7990钢结构用六角头螺栓hexagon head bolts for steelstructuresGB1229-84201 DIN7991 内六角沉头螺钉hexagon socket countersunkhead screwsISO10642202 DIN7993 轴用钢丝挡圈roundwire snap rings for shafts GB895.2-86203 DIN7995十字槽半沉头木螺钉cross recessed raisedcountersunk head wood screwsGB952-86204 DIN7996 十字槽圆头木螺钉cross recessed round head wood GB950-86205 DIN7997 十字槽沉头木螺钉cross recessed countersunk headwood screwsGB951-86206 DIN8140螺纹护套（普通\自锁等）ciol inserts,coarse,fine thread,silf locking207 DIN9021 大外径垫圈washers,outside diameterappro.3dISO7093 GB96-85 208 DIN11024 弹簧卡子spring cotter for a bolt209 DIN13257 平板螺栓belting bolts (elevator bolts)210 DIN18182 干壁钉（墙板钉）dry wall screws211 DIN28129 环型螺母lifting nuts(eye nuts) GB63-88 212 DIN70952 圆螺母用止退垫圈tab washers for slotted roundnutsGB858-88。