日立 钻孔机代码

––CNC番號是error alarm 發生的CNC番號。

––訊息番號訊息的番號表示000~919的番號。

000~199：CNC關係的訊息，和操作軸沒關係。

200~399：機械特有的訊息。

400~599：操作軸關係的訊息。

600~919：操作軸移動方向關係的訊息。

––訊息26各文字以內的訊息。

回復條件START、RESET、EMG表示為回復的條件。

注）狀態訊息是藍色、操作訊息是黃色、error、alarm訊息是以紅色表示。

9-2 MESSAGE TABLENO.000 SYSTEM PARAMETER ERROR EMG 系統參數錯誤NO.001 PARITY（TH）ALARM RESET 紙帶水平同位（TH）警報NO.002 PARITY（TV）ALARM RESET 紙帶垂直同位（TV）警報NO.003 CONSTANT TOO LARGE RESET 常數太大NO.004 INV ALID ADDRESS RESET 位址無效NO.005 INV ALID CONSTANT RESET 常數無效NO.006 ILLEGAL“–”CODE RESET 不合法“–”碼NO.007 ILLEGAL“．”CODE RESET 不合法“．”碼NO.008 UNDEFINE ADDRESS RESET 未定義位址NO.009 UNDEFINE G CODE RESET 未定義G 碼NO.010 UNDEFINE M CODE RESET 未定義M 碼NO.011 INV ALIE END CODE RESET 無效結束碼NO.012 ILLEGAL REPEAT COMMAND RESET 不合法副程式呼叫NO.013 ILLEGAL REPEAT COMMAND RESET 不合法重覆指令NO.014 NO SUCH SUBPROGRAM RESET 未登錄副程式NO.015 ILLEGAL SUBPROGRAM NEST RESET 多重副程式呼叫NO.016 ILLEGAL DOUBLE ADDRESS RESET 不合法重覆位址NO.017 NOT FOUND SEQUENCE NO RESET 未發現順序控制編號NO.018 ILLEGAL S&R CALL RESET 不合法Step&Repeat指令呼出NO.019 INV ALID MACHINE HOME RESET 原點復歸未實施NO.020 ILLEGAL RETURN CODE RESET 不合法程式結束碼NO.021 ILLEGAL S&R RESET 不合法Step&Repeat指令開始NO.022 ILLEGAL S&R END CODE RESET 不合法Step&Repeat指令結束NO.023 ILLEGAL PART PROGRAM RESET 不合法紙帶格式（FORMA T）NO.024 FD FULL RESET 磁碟容量已滿NO.025 FD NOT READY RESET 磁碟片未準備就緒NO.026 ILLEGAL F COMMAND RESET 進刀速設定超出範圍外NO.027 ILLEGAL S COMMAND RESET 回轉速設定超出範圍外NO.028 ILLEGAL T COMMAND RESET 工具徑設定超出範圍外NO.030 FD FILE PROTECTED RESET 禁止File讀出NO.031 FILE WRITE PROTECTED RESET 禁止File寫入NO.032 NO SUCH FILE RESET File未登錄NO.033 ILLEGAL FILE NAME RESET 檔案名程不正確NO.034 LIMIT OF SUBPROGRAM RESET 副程式超出限制NO.035 ILLEGAL S&R NEST RESET 多重Step&Repeat呼出NO.036 ILLEGAL ‘+’ CODE RESET 不合法“+”碼NO.037 CONSTANT OUT OF RANGE RESET 常數超出被定範圍NO.038 ILLEGAL PARAMETER DATA RESET 不合法參數資料NO.039 ILLEGAL COMMAND CONDITION RESET 不合法命令組合NO.040 FORMAT ERROR RESET 格式錯誤（FORMA T）NO.041 DEVICE BUSY RESET 裝置使用中（忙碌）NO.042 ILLEGAL MESSAGE FILE EMG 不合法的訊息檔案NO.043 ILLEGAL MACRO FILE EMG 不合法的巨集檔案NO.044 ILLEGAL SUBPROGRAM START RESET 不合法的輔助程式開始NO.060 END OF PRPGRAM START 作業完了NO.061 PROGRAM STOP START 程式停止NO.062 OPTIONAL STOP START 選擇性停止NO.064 TOP OF PROGRAM START 程式開始NO.067 READY FOR RESTART START 程式準備完畢NO.068 ILLEGAL HEADER COMMAND START 不合法的程式頭指令NO.072 ILLEGAL DEVICE RESET 未定義裝置NO.079 WAITING FOR START START 等待開始狀態NO.080 EMULATER ERROR EMG 內部演算錯誤NO.100 DISK HARDWARE ERROR EMG 磁碟硬體錯誤NO.104 CMOS RAM SUM CHECK ERROR EMG CMOS RAM 檢查錯誤NO.110 DISK HARDWARE ERROR EMG 伺服器尚未就緒NO.111 EXTERNAL IN/OUTPUT START 外部裝置警報NO.113 SERVO OPTICAL FIBER EMG 伺服光纖關係警報NO.114 PARAMETER SETTING ERROR EMG 參數設定錯誤NO.116 SEQENCER OPTICAL FIBER EMG 順序控制光纖關係警報NO.117 DWQENCER HARDWARE DGN.14 EMG 順序控制硬體錯誤DGN.14NO.119 RS-232C 1 ERROR DGN.16 START RS-232C通信埠1 錯誤DGN.16NO.120 RS-232C 2 ERROR DGN.16 START RS-232C通信埠2 錯誤DGN.16NO.122 MAIN CPU ERROR DGN.000 EMG 主CPU硬體錯誤DGN.000NO.123 SERVO CPU ERROR DGN.12,413 EMG 伺服CPU硬體錯誤DGN.12,413NO.126 BPRKEN BATTERY EMG 電池異常NO.127 DNC COMMUNICATION ALARM RESET DNC通信警報NO.199 INTERNAL ERROR EMG 內部錯誤NO.200 ILLEGAL CANNED CYCLE RESET 不當程式指令（DIL IC）NO.201 ILLEGAL CANNED TEXT RESET 不當程式令令（文字）NO.202 ILLEGAL CANNED CIRCLE RESE 不當程式指令（擴大孔）NO.203 ILLEGAL CANNED SLOT RESET 不當程式指令（槽孔）NO.205 ILLEGAL DRILL HIT COMMAND RESET 不當加工指令NO.206 ILLEGAL DRILL CYCLE DATA RESET 不當加工循環資料NO.207 READY FOR REVERSE START 加工反轉就緒NO.208 END OF MACHINE REVERSE START 加工反轉結束NO.209 HOLE NOT EQUAL START 孔數不一致NO.210 ILLEGAL TOOL PATH COMMAND RESET 不當切削加工指令NO.213 ILLEGAL TOOL BIT SELECTION RESET 不當工具別選擇NO.215 NC BUFFER OVER NC RESET NC 緩衝區超出NO.216 PRESS THEN RESET THE EMG STOP RESET 請實施RESET EMG鍵以載入系統NO.250 LIMIT OF TOOL BIT LIFE START 工具壽命終了NO.251 UNDEFINE T CODE START 未定義T CODENO.252 CHANGE OF ATC TOOL BLOCK START 請交換ATC部工具NO.254 ILLEGAL NUMBER OF TOOL RESET 不當工具數分配(TOOLMNG)NO.255 ILLEGAL SPINDLE SELECTION RESET 不當SPINDLE選擇（BH機能）NO.256 CCD SENSOR ALARM RESET CCD感測器警報NO.257 NO DETECTION OF BIT HIGHT START CCD感測器工具長度偵測不到NO.258 TOOL DIAMETER ERR(DGN.181) START CCD感測器工具直徑偵測異常NO.260 CHECK STATION NG1(LONG) START 裝著後確認工具長度（長）NO.261 CHECK STATION NG2(LONG) START 排出前確認工具長度（長）NO.262 TOOL LET OUT ERROR START工具排出錯誤NO.263 CHECK STATION NG1(SHORT) START 裝著後確認工具長度（短）NO.264 CHECK STATION NG2(SHORT) START 排出前確認工具長度（短）NO.265 CHECK STATION SENSOR ALARM START CCD 感測器內有異物檢出NO.266 HIGHT DETECTOR ALARM START CCD感測器工具刃先檢出異常NO.267 TOOL LET OUT ERROR START 工具釋放錯誤NO.268 PANEL HEIGHT SENSOR ERROR RESET 自動R點設定機能感測異常檢出NO.269 AUTO UPLIM DATA ERROR #129 START 自動R點設定機能參數異常DGN.129 NO.270 Z AXIS ORIGIN ERROR RESET Z軸原點復歸錯誤NO.271 X,Y AXIS ORIGIN ERROR RESET X,Y軸原點復歸錯誤NO.275 WORK ZERO ALARM RESET 工作原點錯誤NO.276 BOARD EXCHANGE POS. ERROR RESET 基板交換位置錯誤NO.277 SUPPLY WORK NOT EQUAL RESET 供給基板板數不一致NO.278 NO PANEL ON TABLE RESET 自動R點設定機能基板未發現NO.280 ATC LOCK START ATC鎖住NO.282 M ADDRESS LOCK RESET M CODE鎖住NO.283 REPLACE TOOL PALLET,TOOL NOT A VAILABLE START 請交換供給部工具盤（工具已用完）NO.284 REPLACE TOOL PALLET,SWITH ATCIV ATE START 請交換供給部工具盤（SWITCH ON）NO.285 CHECK POD START 排出，裝著POD確認NO.286 INSERT TOOL INTO COLLET MANUALLY START手動將工具插入COLLET中（粗徑）NO.287 REMOVE TOOL INTO COLLET MANUALLY START手動將COLLET之工具排出（粗徑）NO.290 ATC CHUCK ALARM(LOWER) START ATC CHUCK異狀（下降端）NO.291 ATC CHUCK ALARM(UPER) START ATC CHUCK異狀（上昇端）NO.292 CHECK ATC CHUCK NG(LONG) START 檢查ATC CHUCK 鑽針（長）NO.293 CHECK ATC CHUCK NG (SHORT) START 檢查ATC CHUCK鑽針（短）NO.294 ALL SPINDLES CANCELLED RESET 全部SPINDLE軸取消NO.300 SPINDLE FUSE ALARM START SPINDLE FUSE警報NO.301 SPINDLE INVERTER ALARM EMG SPINDLE變頻器警報NO.302 LOW AIR PRESSURE START 空壓不足NO.303 COLLING UNIT THERMAL ALARM EMG 主軸油冷卻裝置熱電驛警報NO.304 COOLING UNIT TEMPERATURE START 主軸油冷卻裝置油溫警報NO.305 V ACLUM THARMAL ALARM EMG 集塵機熱電驛警報NO.306 ATC POINT ALARM START A TC位置警報NO.307 BDD ALARM START 斷針警報（BDD）NO.308 EXTERNAL DEVICE ALARM START 外部裝置警報NO.310 FRONT DOOR OPENED START 前門被打開NO.311 SAFETY SENSER ALARM 1 START 安全SENSOR警報1 NO.313 SPINDLE OIL SIGNAL RESET SPINDLE油信號警報NO.314 ABC DEVICE ALARM START ABC裝置警報No.315 DRYING UNIT OFF START 空氣乾燥機停止中No.316 WORK CLAMP ALART RESET 基板固定CLAMP機能異常檢出No.317 PIN CLAMP ALARM RESET PIN CLAMP機能異常No.318 WORK PRESS ALARM RESET 押板機能動作異常No.319 SAFETY SENSOR ALARM RESET 安全SENSOR警報2No.320 XY AXIS INTERLOCK(G64.4) EMG X，Y軸連結鎖住(G64.4) No.321 Z AXIS INTERLOCK(G72.4) EMG Z軸連結鎖住(G72.4)No.322 CUTTING INTERLOCK(G00.1) EMG 切削連結鎖住(00.1)No.323 SPINDLE OFF EMG SPINDLE 停止中No.324 MACHIINE LOCK EMG 機械鎖定No.325 WAITING FOR M-ANS.DGN.039 RESET M CODE等待回應No.326 START INHIBIT EMG 啟動停止No.327 WAIT FOR WARM-UP SPINDLE EMG SPINDLE暖機中No.328 EXECUTING ABC CYCLE EMG ABC動作中No.329 WAITING FOR OPERATINO START 等待狀態No.330 END OF PROGRAM START 作業完了No.331 PUSHING WORKPRESS EMG 押板機能動作中No.337 ABC NOT READY START 外部裝置ABC未就續No.346 PACK COMMUNICATION ALARM X11-12 EMG PACK通訊異常No.347 DEAE STOP ERROR EMG 超極限檢出警報No.350 BDD ALARM RESET 斷針警報(BDD)No.351 PRESET SCHEDULE EMG 1V/1W加工異常No.352 SELECTED ILLEGAL MODE RESET 加工模式異常No.353 RECLINNING ALARM RESET 板架柵欄警報(ABC) No.354 TOOL ASSINGNMENT ERROR，RESET 工具分配錯誤，檢查工具CHECK ON TOOL PALLET PAGE 分配頁No.403 X ENCODER ALARM EMG X軸編碼器警報No.405 X OVER SERVO DLOOP EMG X軸伺服迴路超出行程No.406 X AXIS INTERLOCK EMG X軸聯結警報No.407 X VELOCTY ALARM EMG X軸速度警報No.408 X REFERENCE POINT ALARM EMG X軸參考點警報No.409 X SERVO ALARM EMG X軸伺服關係警報No.413 Y ENCODER ALARM EMG Y軸編碼器警報No.415 Y OVER SERVO DLOOP EMG Y軸伺服迴路超出行程No.416 Y AXIS INTERLOCK EMG Y軸聯結警報No.417 Y VELOCTY ALARM EMG Y軸速度警報No.418 Y REFERENCE POINT ALARM EMG Y軸參考點警報No.419 Y SERVO ALARM EMG Y軸伺服關係警報No.423 Z1 ENCODER ALARM EMG Z1軸編碼器警報No.425 Z1 OVER SERVO DLOOP EMG Z1軸伺服迴路超出行程No.426 Z1 AXIS INTERLOCK EMG Z1軸聯結警報No.427 Z1 VELOCTY POINT ALARM EMG Z1軸速度警報No.428 Z1 REFERENCE POINT ALARM EMG Z1軸參考點警報No.429 Z1 SERVO ALARM EMG Z1軸伺服關係警報NO.433 Z2 ENCODER ALARM EMG Z2軸編碼器警報NO.435 Z2 OVER SERVO DLOOP EMG Z2軸伺服迴路超出行程NO.436 Z2 AXIS INTERLOCK EMG Z2軸聯結警報NO.437 Z2 VELOCTY ALARM EMG Z2軸速度警報NO.438 Z2 REFERENCE POINT ALARM EMG Z2軸參考點警報NO.439 Z2 SERVO ALARM EMG Z2軸伺服關係警報NO.443 Z3 ENCODER ALARM EMG Z3軸編碼器警報NO.445 Z3 OVER SERVO DLOOP EMG Z3軸伺服迴路超出行程NO.446 Z3 AXIS INTERLOCK EMG Z3 軸聯結警報NO.447 Z3 VELOCTY ALARM EMG Z3軸速度警報NO.448 Z3 REFERENCE POINT ALARM EMG Z3軸參考點警報NO.449 Z3 SERVO ALARM EMG Z3軸伺服關係警報NO.453 Z4 ENCODER ALARM EMG Z4軸編碼器警報NO.455 Z4 OVER SERVO DLOOP EMG Z4軸伺服迴路超出行程NO.456 Z4 AXIS INTERLOCK EMG Z4軸聯結警報NO.457 Z4 VELOCTY ALARM EMG Z4軸速度警報NO.458 Z4 REFERENCE POINT ALARM EMG Z4軸參考點警報NO.459 Z4 SERVO ALARM EMG Z4軸伺服關係警報NO.463 Z5 ENCODER ALARM EMG Z5軸編碼器警報NO.465 Z5 OVER SERVO DLOOP EMG Z5軸伺服迴路超出行程NO.466 Z5 AXIS INTERLOCK EMG Z5軸聯結警報NO.467 Z5 VELOCTY ALARM EMG Z5軸速度警報NO.468 Z5 REFERENCE POINT ALARM EMG Z5軸參考點警報NO.469 Z5 SERVO ALARM EMG Z5軸伺服關係警報NO.473 Z6 ENCODER ALARM EMG Z6軸編碼器光學尺警報NO.475 Z6 OVER SERVO DLOOP EMG Z6軸伺服迴路超出行程NO.476 Z6 AXIS INTERLOCK EMG Z6軸聯結警報NO.477 Z6 VELOCTY ALARM EMG Z6軸速度警報NO.478 Z6 REFERENCE POINT ALARM EMG Z6軸參考點警報NO.479 Z6 Z6 SERVO ALARM EMG Z6軸伺服關係警報NO.600 X+ STORED STROKE 1 RESET X+側超出加工領域檢出NO.601 X–STORED STROKE1 RESET X–側超出加工領域檢出NO.602 X+ STORED STROKE2 RESET X+側使用者設定加工領域超出OT側檢出NO.603 X–STORED STROKE 2 RESET X–側使用者設定加工領域超出OT側檢出NO.604 X+ STORED STROKE 3 RESET X+側超出機械參數設定領域檢出NO.605 X–STORED STROKE 3 RESET X–側超出機械參數設定領域檢出NO.620 Y+ STORED STROKE 1 RESET Y+側超出加工領域檢出NO.621 Y–STORED STROKE 1 RESET Y–側超出加工領域檢出NO.622 Y+STORED STROKE 2 RESET Y+側使用者設定加工領域超出OT側檢出NO.623 Y–STORED STROKE 2 RESET Y–側使用者設定加工領域超出OT側檢出No.624 Y1＋STORED STROKE 3 RESET Y＋側超出機械參數領域檢出No.625 Y1－STORED STROKE 3 RESET Y－側超出機械參數領域檢出No.640 Z1＋STORED STROKE 1 RESET Z1＋側超出加工領域檢出No.641 Z1－STORED STROKE 1 RESET Z1－側超出加工領域檢出No.642 Z1＋STORED STROKE 2 RESET Z1＋側使用者設定加工領域超出OT側檢出No.643 Z1－STORED STROKE 2 RESET Z1－側使用者設定加工領域超出OT側檢出No.644 Z1＋STORED STROKE 3 RESET Z1＋側超出機械參數領域檢出No.645 Z1－STORED STROKE 3 RESET Z1－側超出機械參數領域檢出No.660 Z2＋STORED STROKE1 RESET Z2＋側超出加工領域檢出No.661 Z2－STORED STROKE1 RESET Z2－側超出加工領域檢出No.662 Z2＋STORED STROKE2 RESET Z2＋側使用者設定加工領域超出OT側檢出No.664 Z2＋STORED STROKE3 RESET Z2＋側超出機械參數設定領域檢出No.665 Z2－STORED STROKE3 RESET Z2－側超出機械參數設定領域檢出No.680 Z3＋STORED STROKE1 RESET Z3＋側超出加工領域檢出No.681 Z3－STORED STROKE1 RESET Z3－側超出加工領域檢出No.682 Z3＋STORED STROKE2 RESET Z3＋側使用者設定加工領域超出OT側檢出No.683 Z3－STORED STROKE2 RESET Z3－側使用者設定加工領域超出OT側檢出No.684 Z3＋STORED STROKE3 RESET Z3＋側超出機械參數設定領域檢出No.685 Z3－STORED STROKE3 RESET Z3－側超出機械參數設定領域檢出No.700 Z4＋STORED STROKE1 RESET Z4＋側超出加工領域檢出No.701 Z4－STORED STROKE1 RESET Z4－側超出加工領域檢出No.702 Z4＋STORED STROKE2 RESET Z4＋側使用者設定加工領域超出OT側檢出No.703 Z4－STORED STROKE2 RESET Z4－側使用者設定加工領域超出OT側檢出No.704 Z4＋STORED STROKE3 RESET Z4＋側超出機械參數設定領域檢出No.705 Z4－STORED STROKE3 RESET Z4－側超出機械參數設定領域檢出No.720 Z5＋STORED STROKE1 RESET Z5＋側超出加工領域檢出No.721 Z5－STORED STROKE1 RESET Z5－側超出加工領域檢出No.722 Z5＋STORED STROKE2 RESET Z5＋側使用者設定加工領域超出OT側檢出No.723 Z5－STORED STROKE2 RESET Z5－側使用者設定加工領域超出OT側檢出No.724 Z5＋STORED STROKE3 RESET Z5＋側超出機械參數設定領域檢出No.725 Z5－STORED STROKE3 RESET Z5－側超出機械參數設定領域檢出No.740 Z6＋STORED STROKE1 RESET Z6＋側超出加工領域檢出No.741 Z6－STORED STROKE1 RESET Z6－側超出加工領域檢出No.742 Z6＋STORED STROKE2 RESET Z6＋側使用者設定加工領域超出OT側檢出No.743 Z6－STORED STROKE2 RESET Z6－側使用者設定加工領域超出OT側檢出No.744 Z6＋STORED STROKE3 RESET Z6＋側超出機械參數設定領域檢出No.745 Z6－STORED STROKE3 RESET Z6－側超出機械參數設定領域檢出No.1000 DOWN LOAD ERROR POWER OFF 下載警報No.1001 ILLEGAL MESSAGE FILE POWER OFF 不合法訊息檔案No.1002 COMMON PARAMETER ERROR POWER OFF 參數錯誤No.1003 FD TASK CREATE ERROR POWER OFF FD工作建立錯誤No.1005 SUBSYSTEM NOT ENTRY POWER OFF 副系統未就續No.1006 SUM INTERNAL ERROR POWER OFF SMU內部錯誤No.1007 PUBDEF NOT ENTRY POWER OFF PUBDEF未進入No.1008 PUBDEF AREA OVER POWER OFF PUBDEF超出範圍No.1039 MCU COMMAND TIME OVER POWER OFF MCU指令時間超過No.1040 CNC POWER ERROR POWER OFF CNC電源警報No.1041 SMU RAM PARITY ERROR POWER OFF SMU RAM同位元檢查錯誤No.1042 BUS DEAD LOCK POWER OFF BUS 死結No.1043 SMU BUS ERROR POWER OFF SMU BUS錯誤No.1044 CNC THERMAL ALARM POWER OFF CNC溫度警報。