闪光灯控制说明书

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Thank you for purchasing a Nissin productBefore using this commander unit, please read this instruction manual and refer to the manual of camera owner carefully to get a better understanding of the proper operation to enjoy flash photography.The commander Nissin Air 10s (Canon/ Nikon/ Sony) is an advanced commander for wireless flash shooting.It controls up to 8 groups of NAS (Nissin Air System) flash (Canon/ Nikon/ Sony) that have a wireless multiple flash shooting function using NAS (radio transmission). Please note that Nissin Air 10s (Canon/ Nikon/ Sony) are not usable with other branded cameras for TTL operation.Please refer to Nissin’s compatibility chart shown here:/download.htmlNissin Air System (NAS) is a Nissin wirelessly remote control flash light system, designed by Nissin. It consists of a Nissin radio commander (NAS commander) and the Nissin wireless flash (NAS flash) and Nissin radio receiver (NAS receiver) as remote slave units.Insert Air 10s on the camera hot shoe as a NAS commander.The signal of Air 10s is transmitted by using 2.4 GHz transmission.Transmission distance is approx. 100m (330 ft.)(Metal/ Wire/ Wall/ another 2.4 GHz radio frequency may cause areduction in the NAS transmission distance)These safety instructions refer to important information on how to use this product safely and properly. Please read the following instructions before using the product.This sign refers to conditions which may cause damage or defect.Do not touch the inside parts from the opening when the unit was dropped or broken.Place the batteries correctly in position. Placing the batteries in wrong polarity maycause leakage, exothermic heat or explosion.Do not leave or store the commander unit in the temperature over 40ºC/ 104ºF, such as in the automobile.The commander unit is not water resistance. Keep the unit away from rain, snow and humidity.Do not use benzene, thinner or other alcoholic agents to clean the unit.Do not use this commander unit with cameras which are not recommended in thecompatibility list at official website, otherwise it may damage the camera’s circuitry(*).Remove the batteries when not in use for a longer period of time.Do not use the Nissin Air 10s to pick up whole camera system when it installed on your camera. To pick up the whole camera system, you should hold the handle of camera body or the lens..* Please refer Nissin’s compatibility chart shown here:/download.htmlGroup selection buttonGroup on/off buttonModeling light button(Basic/Advanced Groups button)Shutter cable socket (2.5mm)M/TTL Mode Button123456LCD panelSelect dial with buttonsChannel buttonHSS buttonBuzzer buttonM.Zoom buttonPanel Lock/Unlock button (hold 1sec.)789101112131415(1) The AF-assist lamp supports digital system cameras measuring autofocus in the center of the image field only. It does not support other camera brands, other types of Canon, Nikon and Sony cameras or camera models without our compatibility test.Pilot button (Test flash button)Power On/Off button Unlock button Micro SD card slot(for firmware update)Strap hole (2) (strap is not included)Battery compartment door AF-assist light (1)Hotshoe contactsInserting batteries1. Open the battery compartment door andinsert 2 x size AAA batteries as shown in the picture.2. Make sure the + and - battery contacts arecorrectly inserted in the battery compartment.3. Close the battery compartment door andslide it back in place.It is recommended to use 2 batteries of the same brand and type, and replace them all at the same time.Wrong insertion of each battery would not make electric contact.(*) Air 10s has an energy saving power off functionTo save battery energy, the screen of Air 10s display dims in about 30 seconds and turns off in about 2 minutes automatically after the setting job is terminated. While Air 10s is in the stand-by mode, a blinking signal will be shown on the Pilot Button. To turn on Air 10s again, press any button on the Commander. In case of not in use for over 60 minutes, Air 10s will be turned off completely. To turn on Air 10s again, press Power button on the Commander.Press power on to activate Nissin Air 10s,hold the Pilot button for 5 seconds to reset to factory default setting Default setting:1. TTL mode: +/- 0EV2. M Manual mode: 1/2563. Zoom setting: Manual, 24mm4. Channel Setting: no. 25. HSS mode: off6. Buzzer: off7. Group Mode: Basic Groups8. Group status: all onDo not use the Air 10s as a holder to pick up the whole camera system.Mounting Air 10s on the cameraRemoving Air 10s from the cameraTurn off Air 10s.Turn off Air 10s.Insert the mounting foot of Air 10s into thehotshoe of the camera.1.2.Make sure that the mounting foot will lock(with a “click”) when it has been insertedcompletely.3.Hold the unlock button andslide the mounting foot of Air 10s off the hotshoe of camera.1.2.Pairing SettingStep 1: Swith all flash and Commander offTo perform wireless shooting, set the Nissin Air 10s commander andNAS slave unit with the following procedure. After pairing is completed, both of them will memorize the data and there will be no need to pair again after the units are switched on and off.1. Hold the "Set" and Power “ON/OFF” buttons for 3 seconds at the same time.3. Nissin Di700A will automatically be changed to wireless slave modeafter Pairing completed.Nissin flash Di700AFor Sony Camera2. “Beep” sound persists until the Pairing signal from commander is received. When the "beep" sound stops, the pairing is complete.1. Switch on your Nissin i60A, hold the "Channel" button for 2 seconds to check and make sure the channel setting in the display is in the "A" Auto channel mode.2. Turn off the Nissin i60A.4. “Beep” sound persists until the Pairing signal from commander is received. When the "beep" sound stops, the pairing is complete.Nissin flash i60A3. Hold the Panel Lock key and the “On & Off” button of Nissin i60Aat the same time for 3 seconds..1. Rotate the "Ch" channel dial to "Auto" auto channel mode.3. “Beep” sound persists until the Pairing signal from commander is received. When the "beep" sound stops, the pairing is complete.Nissin flash MG102. Hold the "Open" button and the power button for 3 seconds.Before usiung Commander Air 10s, please install Air 10s oncamera and change the Flash mode to “WL” in camera menu.Nissin Air R Receiver1. Rotate the "Ch" channel dial to "Auto" auto channel mode.2. Hold the power button for 3 seconds3. “Beep” sound persists until the Pairing signal from commander is received. When the "beep" sound stops, the pairing is complete.Step 2: Pairing on Nissin Air 10s commander1. Start the Pairing mode of all slave units and the "beep" sound are constantly heard.2. Turn off Nissin Air 10s then hold the Panel Lock key andthe power “On/Off” button for 3 seconds at the same time.The Pilot LED will blink about ten seconds (the display will not light up while pairing). When Nissin Air 10s Pairing mode has stopped, slave units around the commander will also complete the pairing process one by one, and stop the "beep" sound.3. To check the pairing between Nissin Air 10s and slave units,press the “Pilot LED” button on Nissin Air 10s for test and let NAS flash andthe flash on NAS receiver emit a weak output test flash.(*) Nissin Di700A, i60A ash and Nissin Air R receiver do not support the Channel 1 in Nissin Air 10s. Please use Channel 2 to 8 to pair with those 3 NAS slave unit models.The default channel setting is no. 2.If you want to change this setting then press the channel button for 2 second.Press channel button 2 second to exit setting.CAUTIONSIf strobes still have "beep" sound constantly after finishing the pairing process, this means the pairing process is not complete. Please move your Air 10s towards the Beeping strobes, then turn off the Air 10s and re-do the pairing process by holding Panel Lock key and the “On/Off” button again for 3 seconds.The NAS system is using an independent identity (ID) function to access strobes, the NAS strobes will not be affected by other commanders when-ever they are using the same channel in the same location. A slave unit of Nissin flash or Nissin receiver can only be controlled by one and only one NAS commander with pairing in default setting.Air 10s offers “Open Mode” ,a new function (only works with MG10), on the pairing setting. Open Mode can let two or more camera using same set MG10 in one place.1. Hold the button of Nissin Air 10s for 1 seconds,lights up on lower left corner means Open Mode is on.Now hold the for 1 seconds again to turn off.There are basic groups and advance groups for controlling the Nissin Air10s. They allow the user to pair an unlimited amount of slave units. They mainly divided into two kinds of groups:Basic groups and advance groups can beuse at the same time for different strobes.Example:Use the i60A in basic group A on manual,use two MG10 in advance group A & D inTTL and manual mode.M modeM/TTL modeTTL mode1. Power on Nissin Di700A and switch to wireless slave mode, press “Set ” several times until the (Group mode in the display),Air 10s, provides individual control of 4 groups (strobes), you can set these 4 groups in different settings. Before shooting, you have to set each strobes to be one of these 4 groups.A B C //A B C //1. Use Mode Dial to chang group . 1. Use Mode Dial to chang group .A B C //1. Use Mode Dial to chang group .In testing or changing the flash effect of different slave units group,you can turn on or turn off any group.will be appeared on the right side of the group. When the group is switched off, only "---" is shown.2. Press the “Group Selection” button when finish setting.For exampleA & C: on,B & D: off A & C: off, B & D: onWhen the NAS flash is set to the wireless mode, all exposure settingfunctions will be controlled by the NAS commander.In Basic groups mode: Press the button.In Advanced groups mode:To set different exposure in each group:1. Press the Group Selection button. When the letter “A” blinks,press M / TTL mode button to change the exposure(the same procedure works with groups B, C, and D).2. After completing the exposure setting,press the Group Selection button again to stop the blinking.1. Press the Group Selection button, the group letters blink.2. Rotate the Operation Dial to increase or decrease the TTL flash exposure compensation.The settings of TTL auto exposure compensation on Nissin Air 10s startsfrom -2EV to + 2EV and controlled by 1 / 3EV step interval.3. When the exposure compensation setting is completed,press the group selection button again.Switching Air 10s from TTL mode to M mode, the last flash power settingwill be saved in TTL control. Flash power value will also remain unchanged in M mode.If you do not press any group selection button which means all group letters in the display do not blink, rotate the Operation Dial to increase/ decrease the power of all groups. For example, A: 0EV, B: + 0.6EV, C: + 1EV, D: -1EV, do not select anygroup then turn the Operation Dial clockwise in 2 click intervals, will cause to A:+ 0.6EV, B: + 1.3EV, C: 1.6EV, D: -0.3EV.1. Press the Group Selection button, the group letter blinks.2. Rotate the Operation Dial to increase or decrease the flash power of the group selected.The setting of M mode on Air 10s starts from 1/256 (minimum) to 1/1 (Full), andcontrolled by 1/3 step intervals. The value digi displayed next to the grouponly shows the integer step value (*).If you do not press any group selection button which means all group letters in the display do not blink, rotate the Operation Dial to increase/ decrease the power of all groups. For example, A: 1/256, B: 1/8 + 0.6EV, C: 1/4, D: 1/2, do not select anygroup then rotate the Operation Dial clockwise with 2 intervals, it becomesA: 1/256 + 0.6EV , B: 1/4 + 0.3EV, C: 1/4 + 0.6EV, D: 1/2 + 0.6EV.Nissin Air 10s offers "A" auto zoom mode and manual zoom mode.1. Hold the for 2 seconds.2. Press the group selection button until the the desired letter(s) blink.Rotate the Operation Dial to change the Zoom head position setting.The focal length is representing the flash angle. Rotate the Operation Dialin anti-clockwise direction to decrease the value of the focal length of zoom head.Keep rotating anti-clockwise to change the "A" automatic zoom mode at the end.Rotate the Operation Dial in a clockwise direction to leave.The “A” auto zoom mode will increase the value of the focal length value of zoom head. Coverage range supports 24mm, 28mm, 35mm, 50mm, 70mm, 85mm,105mm, 135mm and 200mm focal length lenses.3. Press the group selection button again after completion of the zoom setting.Hold for 2 seconds again when all groups zoom settings are completed.If you do not press any group selection button, which means all group letters in the display do not blink, rotating the Operation Dial to increase or decrease the flashzoom head focal length will affect all groups; A, B, C and D.Normal flashguns have a very short flash duration. In order to estimate and control the flash more efficiently, the modeling light on slave unit can be used. It is a constant light for the user to estimate and preview the lightbefore shooting(flash emitting).(*) Modeling light is a new feature of the NAS system.Nissin Di700A, i60A, i40 flash and other discontinuedmodels do not support this feature.1. Press the Group Selection button(s), the group letter(s) blink.2. Press to switch the group’s modeling on/off.3. Press the Group Selection button again when setup completed.1. Press on Air 10s for 1 second to switch to theadvanced groups.2. Press to change to M mode.2. Press to turn on modeling light.If you do not press any group selection button, which means all group letter in the display do not blink, pressing the modeling light button will invert the modeling on/off setting of all groups. For example, A & C: On and B & D: off, press the modelinglight button without selecting any group, will cause to A & C: Off, and B & D: On.Flashgun supports shutter speed limitation on X-Sync (maximum speed synchronizeto flash) on SLR / DSLR /Mirrorless Cameras in general. If it does not supportHSS function of the camera, faster shutter speed settings than the maximum synchronize speed will block the flash gun. With faster shutter speeds than the maximum sync speed some part(s) of the image area would be shaded by the moving shutter leaves withinthe flash duration. As a result the image is only partially exposed by the flash light.”. HSS allows flashgun works under high speed shutter (max 1/8000s).Method A (for Canon & Sony)Hold button for 2 seconds to turn on or off.Method B1. Insert Air 10s to Canon camera shoe.2. Switch on both Air 10s and Camera,For Canon: Menu setting External Flash setting HSS mode in the sync settingFor Nikon: Custom setting menu Flash Flash sync speed Auto FPThe flash emitting operation in HSS mode is different from the normal flash mode.With the HSS function, users can get a faster shutter speed which will result ina lower guide number. This is equivalent to a lower flash output. The flash of HSScannot be measured by an external light meter. When HSS is on,the exposure compensation setting of TTL mode offers the same -2EV to +2EV ofbasic mode. Using the power control of "M" Manual mode under HSS,the Air 10s offers 1/32 to 1/1 power range only. If power is set from 1/256 to 1/64+0.3EV, “M” manual power setting will automatically change to 1/32 in HSS mode.All settings of strobes are controlled by the commander wirelessly after the pairing is completed. If the strobes buzzer is on, a “Beep” sound will be heard when the Strobe is charging and not ready to flash. The “Beep” sound will be heard everytime when there is any change made through the commander.Hold button to switch the buzzer (on strobes) on or off.When “no buzzer” logo is displayed in LCD, it means that the beep sound is off.When the “no buzzer” logo disappears, then the buzzer function is turned on.To start the firmware update procedure, you need to have:The computer (Windows or Mac) connected to the InternetA Micro SD/SDHC card (recommend 4GB-32GB) and Micro SD card reader.Air 10s with 2pcs of full re-charged AAA batteries.1. Download the Firmware file(s). Click here to download firmware files:http: ///firmware.html2. Insert Micro SD/SDHC card to the card reader and connect to the computer.3. Format Micro SD/SDHC card under FAT32 format (Please backup before format).4. Copy all Firmware file(s) to Micro SD/SDHC card.5. Eject the Micro SD/SDHC and remove from the card reader.6. Insert AAA batteries into Air10s and switch on it.7. Then switch off the Air 10s.8. Remove the Micro SD/SDHC cover of Air 10s, insert the Micro SD/SDHC whichcontains the latest firmware update files into the Air 10s.9. Switch on the Air 10s. A LED light inside the Micro SD card slot of Air 10s will blink, it will blink and the light will change orange to red and stop blinking oncethe update is finished.10. The green light will emit when the firmware update procedure is completed.Remove the batteries and remove the Micro SD/SDHC.11. Insert the batteries again and switch on the Air 10s.for 5 seconds. LCD display will show 2 differentfirmware versions. Release the Power button about 2seconds, firmware version page will disappear andreturns to the front operation page.(1) This is a testing result record, it may be affected by equipment and environmental factors.(2) This is a new feature which supports a coming new NAS flash.TypeWireless systemRadio specificationsChannelFlash GroupsTransmission distanceRemote flash control systemWireless flash exposure mode Supporting TTL Exposure control Flash sync mode Zoom mode (Flash coverage area)Special features AF-assist beam effective range Display Firmware update Power supply Continuous flash speed Battery Life Hot shoe Size Weight Accessories includedCanon / Nikon / Sony NAS 2.4GHz ISM band (to obtain technical standards certification)8 channels (channel setting in Air 10s)8 groups (2) : A , B , C , D & Ȧ ,Ḃ , Ċ ,Ḋ100 meters (1)TTL automatic flash exposure mode with +/-2EV compensation and in 1 / 3EV step intervals;M manual flash output mode, offers 1/256 to 1/1control with 1/3 step intervals[TTL] i-TTL ( Nikon) / E-TTL II / E-TTL (Canon)[manual]/ ADI/ PTTL (Sony)1st curtain & 2nd curtain sync., red-eye reductionHSS (up to 1 / 8000s ), slow shutter sync.Auto Zoom, 24mm, 28mm, 35mm, 50mm,70mm, 85mm, 105mm, 135mm and 200mmModelling light on remote flash (2) , Advancedgroups (2) , TTL memory0.7 to 5 meters (1)LCD color displayMicro SD / SDHC (up to 32GB) (Not included)2 x AAA (not included)Up to 10 shots per secondApprox. 3,000 shots (using alkaline batteries)(1)Metal shoe (3) with quick release lockApprox. 65(W) x 60(H) x 60(D) mm73g / 2.6 oz (without battery)Protection case, 2 shutter release cablesWarrantyIn case of the following reason of the defect, it may void the warranty.1. The product is not used in accordance with the instruction of the owner’s manual.2. The product is repaired or modified by the one who is not an authorized repair service.3. When the product is used with the cameras not applicable, lens, adaptors or such accessories produced by the third party.4. Fault or defect caused by fire, earthquake, flood, public pollution and such natural accident.5. In case that the product is stored in dust, moisture, extremely high temperature or such poor condition.6. Scratch, blemish, crush or worn out by a violent use or treatment.7. Guarantee card without name of place purchased or date of purchase stamped, or no guarantee card.Please refer the respective warranty condition for details which depends on the country of purchase and contact our official distributors who distributed this product for the warranty arrangement details.Nissin Japan Ltd., Tokyo Nissin Marketing Ltd., Hong Kong 。

永诺YN568EX闪光灯说明书一、警告请勿让本产品淋雨或受潮，以免发生火灾或触电。

处理电池时，请将电池的触点包裹好以避免短路，并请遵守好当地有关处理电池的规定。

请将电池或容易误吞的东西远离儿童存放，如果误吞了物体，请立即与医生联系。

不要近距离对人体的眼睛使用闪光元件，否则有可能对人体视网膜造成伤害。

不要对需要高度注意力的人使用闪光灯，否则有可能引发安全事故。

如果发生以下情况，请立即取出电池并停止使用。

本产品跌落或受到强烈冲击，使产品的内部裸露。

电池内部腐蚀性液体泄漏，此时应带手套取出电池。

产品发出奇怪的气味，发热或冒烟。

请勿自行拆卸或维修本产品，如果接触产品内部的高压电路，可能会触电。

长期不使用本产品时，请取出所有电池。

二、产品特点支持高速同步可支持高速同步TTL 闪光，您可以在所有的快门速度下同步使用 YN568EX 闪光灯，最高快门同步达 1/8000秒。

兼容 N 家、C 家无线闪光系统同一台 YN568EX 可分别接受580EX II、SB-900/800/700、7D/60D/600D 内闪、N 家相机 C 指令、SU-800及ST-E2 无线信号，支持 4 个频道，实现离机 TTL 及手动闪光。

大尺寸 LCD 显示屏大尺寸 LCD 显示，可更清晰、更直观地查看及设置闪光功能，使用更便捷。

GN58 ISO100，105mmYN568EX 为永诺新型高指数闪光灯，支持 TTL、M、Multi 闪光。

多种触发同步方式，灵活多变YN568EX 可以通过相机机顶触发、内置或主控闪光灯指令触发、S1 和 S2 避预闪触发。

配备灯头电动变焦功能通过操作闪光灯上的变焦按钮，可以使灯头覆盖焦距在 auto，24,105mm 之间变动。

全面支持TTL 功能支持高速同步、曝光补偿、曝光包围、后帘同步、曝光锁定、光圈预览造影闪光、佳能相机菜单访问。

远程无线触发感应YN568EX 具备远程无线触发感应功能;Sc/Sn/S1/S2 模式可工作于户外环境，无线触发感应距离长达 15 米。

迅丽TTL 机顶闪光灯Thinklite TTL Camera FlashINSTRUCTION MANUAL 说明手册中英文双语 / Chinese English Bilingual在使用本产品之前：请先仔细阅读本手册，以确保您能安全使用。

请保存好本手册以备将来查询参考。

For NikonBefore using this product:Please read this user manual carefully in order to ensure your safety and the proper operation of this product . Keep for future reference.705-TT685N-00地址/Add: 深圳市宝安区福海街道塘尾社区耀川工业区厂房2栋1层至4层、4栋1层至4层1st to 4th Floor, Building 2/ 1st to 4th Floor, Building 4, Yaochuan Industrial Zone, Tangwei Community, Fuhai Street, Bao’an District, Shenzhen 518103, China 电话/Tel: +86-755-29609320(8062) 传真/Fax: +86-755-25723423邮箱/E-mail: ***************深圳市神牛摄影器材有限公司GODOX Photo Equipment Co., Ltd.Made In China感谢您购买神牛产品。

该型号机顶闪光灯适用于Nikon 系列相机，兼容i -TTL 自动闪光。

使用i -TTL 闪光灯。

您将获得更简单的拍摄体验，在光线变化复杂的情况下，可以自动获得准确的闪光曝光，拍摄轻松自如。

产品特点突出表现在以下几方面：● GN 60 (m ISO 100, @200mm), 22级调光(1/1~1/128)● 兼容尼康i -TTL支持i -TTL自动闪光，可作为无线多灯闪光系统的主控或从属单元，拍摄更简单快捷● 点阵液晶屏显示直观，操作更加简易● 内置2.4G 无线传输收发一体，超远距离，创意无限● 无线功率遥控触发选购FT-16S 遥控器，可对离机闪光灯进行无线功率调节等参数设置，同时触发引闪● 功能齐全，无限享用支持手动和频闪闪光模式，高速同步/第二帘快门同步/闪光曝光补偿等i -TTL 功能● 光学研究，输出稳定高速连闪，每次输出亮度和色温连续一致(5600±200K)，光线均匀分布● 固件升级，兼容无忧跟随原厂相机步伐，可对软件进行再升级前言请保持干燥。

MINI-ZOTLightweight LED Strobe Light with BracketUser ManualPlease read the instructions carefully prior to use3A2AFor safety reasons, any modifications o f th is device voids its warranty.Furthermore, any other operation may lead to short-circuit, burns, electric shock, lamp explosion, crash, etc. If this device is operated in any way different to th atdescribed in this manual, the product may suffer damage and the warranty becomes void.CLEANING AND SERVICINGThe tips below should be followed when performing service : 1) All installation screws need to be tightly fastened and must not be corroded.2) There must not be any deformation from heat on the housing, lens , bracket, orinstallation surface .3) The electric power cables must not show any damage, material fatigue , orcorrosion .We recommend a frequent cleaning of th is device. Please use a moist, lint-free cloth. Never use alcohol or solvents.CAUTION: Disconnect from main power prior to servicing this device !FEATURES AND SPECIFICATIONS L ightweight high-tech plastic case A djustable flashrate (1-10 flashes/sec.) Adjustable flash speed by knob V ery low power consumptionV ery low heat without the need for a fan P erfect for decorations or party-rooms Power requirement : 110 V AC, 60Hz Power consumption: 10 wattsLIGHT SOURCE : 63 9mm bright white LEDs Carton Size : 5.91" dia. X 7.87" L WEIGHT : 1.76 lbs.1AThank you for cho o s ing the Talent MINI-ZOT . For your safety, please read this user manual carefully before installing the device.SAFETY INSTRUCTIONSIf the device has been exposed to temperature or environment condition changes, do not switch it on immediately. Resulting condensation could damage the device. Leave the device switched off until it has reached room temperature.This device falls under protection-class I. Therefore it is essential that the device be grounded .Make sure that the available voltage is not higher than stated on this device: 110 VAC . Never operate the stroboscope without the glass pane or with a broken glass pane.En sure the power cord is never crimped or damaged. If it is damaged, ask your dealer or authorized agent to replace the power cord.Always disconnect from power when the device is not in use or before cleaning it. Only handle the power cord by the plug. Never pull the plug out of the wall using the power cord. During initial start-up, some smoke or smell may arise. This is normal and should decrease gradually. CAUTION:1. Be very careful during installation.2. Never look directly into the light source . Those diagnosed with epilepsy could suffera seizure from the output of this fixture.3. Please be aware that damages caused by modifications to the device are notsubject to warranty. Keep away from children and non-professionals. GENERAL GUIDELINESThis device is a stroboscope for decorative effects. This device is only allowed to be operated with 100 to 120 VAC, 60 Hz and is designed for indoor use only.Do not shake the device. Avoid brute force when installing or operating it.When choosing the installation spot, please make sure that the device is not exposed to extreme heat, moisture , or dust. The minimum distance between light-output from the projector and the illuminated surface must be more than 1-1/2 feet .Operate the device only after having familiarized yourself with its functions. Do not permit operation by person not qualified to operat e th is device. Most damages are the result of unprofessional operation.Please use the original packaging if the device is to be transported.。

97169MANUAL FLASH CONTROLThis flash unit provides manual flash mode, allowing you to control the light output at your desired level. 6 power settings 1/1, 1/2, 1/4, 1/8, 1/16 and 1/32 are available. To use the manual mode, please follow the instruction below:(1) Tap the MODE button until the “M” indicator shows up on the LCD.(2) Then press the “ ” or “ ” selector button to set your desired flash output level. The setting will then be automatically saved to the internal memory.The LCD automatically shows a flash-to-subject distance required for correct exposure.SLAVE MODEOptical slave sensor is built into this flash unit, so it can be used as a slave flash. It can instantly synchronize with external trigger (S0 Mode).The amount of light output at slave mode can be set in manaul mode. The following guides you through how to use the slave function of this flash:(1) Follow the instructions in the section ‘MANUAL FLASH MODE’ to set the output power of the flash.(2) Tap the MODE button till the indicator ‘S’ (Slave) and ‘0’ shows up on the LCD.FLASH SYNCHRONIZATIONSynchronization time refers to the shutter speeds that enable flash photography. Each camera model features a “shortest” synchronization called x-synchronization. Please refer to the user guide of your camera for details. Shutter speeds slower than the x-synchronization should never be used in order to avoid incorrect exposures.When the camera is in program mode (P) or aperture-priority mode (A), and an external flash unit is used, the x-synchronization of the camera will automatically be adjusted to assure proper exposure. The sync speed depends on the camera models and usually ranges between 1/30sec to 1/250sec.When a flash shot has been taken, "OK" indicator lights up shortly to confirm correct exposure.SLOW SYNCHRONIZATIONThe Slow Synchronization function is available with cameras that support this feature. The flash is controlled at a slow shutter speed to obtain the correct exposure for both the main subject and background in low-light situations or at night.This function can only be set on the camera, not on the flash unit. For more information, refer to your camera manual.As slow shutter speeds are normally used for slow sync, a tripod is recommended to prevent camera shake.FRONT AND REAR-CURTAIN SYNCHRONIZATIONSome cameras offer the option of rear curtain synchronization (Rear mode) triggering the flash unit at the end of the exposure time. Rear curtain synchronization is particularly advantageous when using slow shutter speeds (slower than 1/30 sec.) or when shooting moving objects that have their own source of light. Rear curtain synchronization gives a more realistic impression of movement because the light streaks behind the light source instead of building up in front of it, as is the case when the flash is synchronized with the front shutter curtain. Depending on its operation mode, the camera uses shutter speeds slower than its sync speed.For Type P flash: You could select the synchronization mode as either front curtain ( ) or rear curtain( ) at the back of the flash. The flash will fire according to the mode selected to match with the camera shutter.For Type C, N, OP, SA flash: The camera controls front or rear-curtain synchronization, therefore no setting is required to be done on the flash.RED EYE REDUCTION (FOR TYPE N, OP, P)To prevent the center of your subject’s eyes from appearing red in color pictures, the flash unit fires pre-flashes at reduced output just before the picture is taken.The Red Eye Reduction function is available with cameras that have red-eye reduction control. This function can only be set on the camera, not on the flash unit. For more information, refer to your camera manual.WIRELESS TTL FUNCTIONThis flash is equipped with advanced wireless TTL flash function. It can synchronize with a master flash or the camera’s built-in flash through TTL. You can use your flash away from the camera but still enjoy the convenience of TTL photography.Before going thru the operation, you should be familiar firstly with the following nomenclature used in wireless flash photography:Master flashThe camera’s built-in flash, a flash unit mounted on the camera, or the one directly connected to the camera via a extension cord is called the Master Flash. Only one master flash is allowed in a wireless multiple flash photography setting. It controls how the Remote Flashes are operated in Wireless TTL mode.Remote flashThe flash unit placed off the camera is called “Remote Flash” (Canon calls it “Slave’’). There is no limitation on the numbers of remote flash to set in one time. GroupsIn wireless photography, you can assign remote flash units into any one of the three groups (A, B, or C) and set the mode and output level compensation values for each remote flash unit.ChannelsThe master and remote flash units exchange data through channels. In this flash, three channels 1, 2 and 3 are available. You pick the channel you prefer for communication between the master and remote flash units.If another photographer uses the same type of wireless photography setup nearby, your remote flash units may accidentally fire in sync with that photographer’s master flash unit. Therefore, you should choose the channel carefully in order to avoid such situation. How to useThis flash can be used as a remote flash in wireless multiple flash photography. To do this, please follow the instructions below:(1) Tap the MODE button until the indicator STTL (Wireless TTL mode) shows up on the LCD. (2) Press the “ ” or “ ” selector button to set your desired wireless TTL channel and group.For Type C, N, and O flash: Each tap on the “ ” button changes the wireless channel and group setting in the following sequence: 1A → 1B → 1C → 2A → 2B → 2C → 3A → 3B → 3C. The “ ” button changes the setting in reverse steps.For Type P and SA flash: Pentax and Sony do not support grouping of flashes in a channel. Therefore, Each tap on the “ ” button changes the wireless channel setting in the following sequence: 1 → 2 → 3. The “ ” button changes the setting in reverse steps.You will see a red light blinking continuously from the front red Iens when the wireless TTL function is activated.If you are using multiple flashes in your wireless photography setting, you should avoid setting more than 3 flash units in one group in order to avoid interference between flashes.(3) Set your preferred flash coverage angle by pressing the ZOOM button.(4) Place your flash unit in consideration of the followings:a. The flash should not shoot its light directly into the camera lens.b. Make sure that the wireless sensor is facing the master flash and the path is not blocked.c. In the daylight synchronization, the wireless sensor may possibly be saturated by sunlight and its sensitivity be extremely reduced. It is recommended that you make a shade to cover the sensor in this situation.Flash setup scenerio in wireless photographyUse the camera’s built-in flash or attach a flash onto the hot shoe of the camera as your master flash.Set up the remote flash/flashes at any desirable location within the effective shooting range.The effective shooting distance between the master and remote flash units is approx. 10m (33 ft.) or less in the front position, and approx. 5 to 7m (16 to 23 ft.) at both sides. These ranges may vary depending on the ambient light.Make sure the channel and the group setting in each remote flash is set correctly. Remote flashes of the same group should be placed together.SAFETY INSTRUCTION• Do not fire flashes from a short distance directly into the eyes of persons or animals. This can cause damage to the retina and may even lead to blindness.• Use only the power sources specified in the operation instructions.• Never attempt to open or short-circuit batteries.• Never expose dry or rechargeable batteries to excessive temperature such as intensive sunlight or fire.• Always switches off the flashgun before changing the batteries.• Do not attempt to open the flashgun because the electronic circuit contains high voltage. There are no components inside the flashgun, which can be repaired by the user.• If in case of the flashgun is so badly damaged that internal components are exposed, the flashgun may not be used until it has been repaired. Remove the batteries to prevent inadvertent use.• Never try to repair the flashgun by yourself. If there are any problems, please contact the customer service. WARNINGThis flash unit may halt and could not function when the battery power is not sufficient or when user operates this unit in an inappropriate wayPlease switch off the flash unit by its main switch when it is not working correctly. Wait for a few seconds and replace the battery if necessary before switching it on again. The flash unit should work again as normal afterward.。

The flash unit has 8 steps of power output control which indicated by 8pieces of LED lamp for different level.Press the MODE key to M Mode. In this mode ,you can set TT560 onto your camera hotshoe or speedlite trigger hotshoe to trigger the flash unit. When shooting,adjust the flash power and press the camera shutter,the flash light will flash under the camera synchronous signal.Press the MODE key to S1 Mode. The mode is applicable for slave flash in order to create many lighting effects. It is respectively applicable for manual flash environment.Press the MODE key to S2 Mode. The mode is applicable for slave flashin order to create many lighting effects.The flash unit won’t flash synchro-nously with the first flash but the second flash from the master flash, which is the second flash synchronization.WARNINGThank you for purchasing GODOX product.Before use, please read this user manual carefully in order to ensure your safety. Keep it properly for reference in future.FOREWORDAlways keep this product from rain or damp in order to prevent fire or electric shock.The flash unit contains high voltage electric parts, do not try to open or repair the flash unit. If you touch the high-voltage circuit inside this product, electric shock may occur. Return it back to the nominated repair service station.If the unit is extruded,fallen,suffered from strong impact and thus its inside is exposed, stop using immediately so as to prevent electric shock leading from touching the inside electric components.Do not fire the flash direct to the eye at short distance(especially baby’s eye), or it may damage the eye.When taking flash picture toward baby, it is recommended to keep the flash unit at least 1 meter(3.3feet) away from the subject. Or use diffuser or bounce the light to soften its intensity. Always keep the battery or anything easy to be gulped out of children's reach. In case of gulping due to carelessness ,please contact a doctor immediately .When there is caustic liquid leakage inside, it is necessary to wear gloves to take out the batter.Do not use the flash unit in the flammable gas, chemical or such liquids. These materials may be ensitive to the flash from the unit in some circ-umstance. It may cause fire or electromagnetic interference.Please pay attention to the warning marks in the shooting surroundings. Do not leave or store the flash unit in temperature over 40 C(such like in the automobile), or it may damage the electronic components. The flash unit isn’t water resistant.Please keep it away from rain or humidity.If the flash unit is idle for long, please take out all batteries and keep the flash unit in dry area.Mini StandSwitch to the ON, the flash will start charging (the charging indicator is dim).After several seconds, the charging indicator turns red and TT560 is ready to shoot.For a test flash, press the test button. After use, press the ON/OFF to OFF to power off.If the red charging indicator lamp flickers in every 1s, it indicates low battery. In such case, the power will turn off automatically and you need to replace the batteries.Number of flashes that will activate over-temperature protection:1/1，1/21/16，1/321/64，1/1281/4，1/8208016040Number Power Level 1.Bounce LightingBounce flash means to take photos by bouncing the light off wall or ceiling to soften the light on the subject, and the shadow shade out, to get more desired picture.e Reflection Board to Take PhotosPull out the refection board and built-in wide panel from the flash head at the same time and then push the built-in wide panel back.In such case, if this product is being used to take photos, it will produce a highlighted point on the eyes of the subject and thus make the eyes charming (catch lights). This function can reach optimal effect when the flash head is up 90°.e Wide-angle DiffuserPull out the built-in wide panel to enlarge flash lighting range, so as to get more softened and natural lighting effect.Systematic over-temperature protectionINSTRUCTION MANUALⅢ. USING TT5601. Power management5.S2 Mode2.Power Control3.M Mode4.S1 ModeⅣ. ADVANCED APPLICATIONⅤ. SPECIFICATIONSⅡ. INSTALLATIONⅠ. NOMENCLATURE38 ( m ISO 100 )Recycle time 100-1500 times (AA alkaline batteries used)4xAAsice batteries(Alkaline or Ni-MH are usable)0~270 degrees0~90 degrees M,S1,S2with 1/8-stop increment5600K+200K 1/300s~1/20000s 190*75*55mm 286gLighting times approx 0.1-5s(AA alkaline batteries used)Light quantity output control Color temperature Flash duration Dimensions Net weightGuide number Flash mode Vertical rotation angle Horizontal rotation anglePowerPress “+” to make power higher and they are 1/128,1/64,1/32,1/16,1/8,1/4,1/2,1/1. Otherwise, press “-” to make power lower.Accessories ：Flash light ......（1） Protecting bag ......（1） Mini stand ......（1） User manual .. (1)。

1. For best flash photography results, set your ISO to 200 and above in both indoor and outdoor conditions.2. After each picture, wait for at least 4-5 seconds for the flash to be fully charged before taking the next shot even when the ready light is on. This will help to prolong the lifespan of the flash tube and help attain the full charging capacity of the flash capacitor for precise flash photography.3. For precise flash output, it is best to wait until an intermittent humming sound is heard before depressing the shutter.4. Maintain at least 2m away from your subject.5. Always set the flash zoom head position according to the zoom position of your camera lens.6. In the event that the flash exposure is incorrect (over or under- exposed or green auto check light does not light up), you should do one of the following: (1) move closer to the subject (2) readjust your bounce or swivel angle (3) adjust flash zoom head (4) Increase ISO setting.7. Bounce or swivel should only be used on light color ceiling or white walls with zoom head set at the 50mm position. Note that when using this feature, 2-3 F stops of light will be lost due to reflection.8. Always use a fresh set of 4 batteries of the same brand and type when old batteries are depleted. Mixing and matching batteries of different types/brands will greatly deteriorate flash performance.9. When flash is not being used for extended period of time (>2 weeks), remove all batteries to prevent battery leakage. After batteries removal, do not expose the flash unit and batteries to excessive heat. 10. Charge up and test fire the flash unit at least once per monthto maintain the optimal performance of the flash tube and charging capacitor.SpecificationsNOMENCLATURE • Guide No: 92ft/28m (ISO100@50mm) • Flash ready indicator in viewfinder • Full digital TTL dedication • Autofocus assistance beam• Zoom, bounce and swivel construction • Automatic standby after 3 minutes • Automatic shutter speed setting • Auto check (OK) indicator • Red eye reduction*• Second/rear curtain synchronization* •Slow synchronization (For Nikon only)• Dedication: ETTL II (Canon), iTTL (Nikon),ADI / PTTL (Sony), 4/3 TTL (Olympus/Panasonic)* Camera dependent features. Please check your camera operating instruction manualZOOM SCALEBASEAUTOFOCUS PROGRAM TTL (P) / AUTO MODEThis flash unit provides automatic Through-The-Lens (TTL) control of the flash exposure when used with dedicated digital cameras. When using this mode, the flash unit will automatically emit the flash output for a balance illumination of the subject and background. The built-in assistance beam will turn on automatically to assist the camera to focus in low lighting conditions.TTL AV, TV AND M MODEWhen this flash unit is used in AV, TV or M mode, the flash exposure will be automatically controlled by the camera based on the combination of shutter speed and aperture value.*For TV mode, do not exceed the maximum camera’s flash synchronization speed. In AV mode, setting at a slow speed will usually result in blurry pictures caused by handshake. In such situation, the use of tripod is recommended.SECOND/REAR CURTAIN SYNCHRONIZATIONThis mode permits you to release the flash just before the shutter closes during slow shutter speed shooting. In this way, a trail of lighting can be taken behind the main subject when slow shutter speed is being used.*For rear curtain synchronization setting, referto your camera instruction manual.AUTO STANDBYWhen the flash is not used for approximately 3 minutes, it will automatically switch to standby mode. Under this mode, the flash will stop charging the capacitor. Even though the flash is in standby mode, it will still consume a small amount of power. To conserve battery power, turn the ON/OFF switch to the OFF position.RED EYE REDUCTIONWhen red eye reduction is activated on the DSLR body,the flash unit will activate a series of pre-flash before the main flash to reduce the possibility of red-eye occurrence during digital photography.USING ZOOM HEADFor proper angle coverage, set the flash zoom position according to the zoom position of the camera lens.USING BOUNCE AND SWIVEL HEADVarious combination of bounce and swivel angle can beused to eliminate unwanted shadow or for softening effect.BATTERIES INSTALLATIONEnsure that the ON/OFF is in the OFF position. Insert 4 new AA batteries according to the battery polarity indicated inside the battery compartment.MOUNTING THE FLASH ON THE CAMERAEnsure that the On/OFF switch is at the OFF position. Slide the flash hotshoe base onto the camera’s hot shoe contact and fasten the lock ring in an anti-clockwise motion. Slide the ON/OFF Switch to the ON position. When the Ready Light lights up, the flash is ready to fire. Pressing the Test Button will fire the unit.For Sony Alpha DSLRs, slide the flash hotshoe onto the camera hotshoe contact until the release button pops up. To detach,simply depress the release button and slide the flash out of the camera hotshoe contact.AUTO CHECK INDICATORThe green auto check indicator located on the back of the flash is used to confirm that your subject is within the effective TTL range of the flash unit. If your subject is within the effective TTL flash range after shooting, the green Auto Check Light will illuminate for approximately 2 seconds.IMPORTANT NOTES FOR FLASHPHOTOGRAPHY AND MAINTENANCEPLEASE READ BEFORE YOU USE THE FLASHFLASH FEATURES© 2012 Energizer Energizer and other marks, including graphics, are trademarks of Energizer and used under license by Bower , Inc. All other trademarks, brand names or product names are the property of their respective owners and are not affiliated with Energizer or Bower , Inc.。

神牛ad500闪光灯说明书
一、产品介绍
1.神牛ad500闪光灯产品主要有X1系列TTL无线引闪系统、赛斯无线引闪器、功率遥控器等几种。

2.神牛ad500闪光灯系列TTL无线引闪系统由X1T发射器和X1R接收器组成。

内置2.4GHz的神牛闪光灯TT600/TT685，可以直接配合X1T发射器组成一个
2.4GHz无线引闪系。

3.神牛ad500闪光灯2.4GHz功率遥控接收器的型号为XTR16(对应外拍灯、影视灯产品)、XTR16S(对应V850/V860机顶灯)。

与X1T发射器搭配，可以实现无线调节输出功率(M挡)和高速同步。

二、产品特点
1.神牛ad500闪光灯闪光时间可精确控制。

2.即时触发/延时触发(触发延时可精确控制)3、光输出瞬时功率大，且光输出瞬时内始终以大率均匀输出。

3.使用寿命长，是普通闪光灯寿命的3-10倍。

三、警告:
请勿让本产品淋雨或受潮，以免发生火灾或触电。

处理电池时，请将电池的触点包裹好以避免短路，并请遵守好当地有关处理电池的规定。

请将电池或容易误吞的东西远离儿童存放，如果误吞了物体，请立即与医生联系，不要近距离对人体。

大华闪光灯_DH-ITALF-300AD 系列快速操作手册V1.0.0浙江大华技术股份有限公司法律声明版权声明© 2018 浙江大华技术股份有限公司。

版权所有。

在未经浙江大华技术股份有限公司（下称“大华”）事先书面许可的情况下，任何人不能以任何形式复制、传递、分发或存储本文档中的任何内容。

本文档描述的产品中，可能包含大华及可能存在的第三人享有版权的软件。

除非获得相关权利人的许可，否则，任何人不能以任何形式对前述软件进行复制、分发、修改、摘录、反编译、反汇编、解密、反向工程、出租、转让、分许可等侵犯软件版权的行为。

商标声明●、、、是浙江大华技术股份有限公司的商标或注册商标。

●HDMI标识、HDMI和High-Definition Multimedia Interface 是HDMI Licensing LLC的商标或注册商标。

本产品已经获得HDMI Licensing LLC授权使用HDMI技术。

●VGA是IBM公司的商标。

●Windows标识和Windows是微软公司的商标或注册商标。

●在本文档中可能提及的其他商标或公司的名称，由其各自所有者拥有。

责任声明●在适用法律允许的范围内，在任何情况下，本公司都不对因本文档中相关内容及描述的产品而产生任何特殊的、附随的、间接的、继发性的损害进行赔偿，也不对任何利润、数据、商誉、文档丢失或预期节约的损失进行赔偿。

●本文档中描述的产品均“按照现状”提供，除非适用法律要求，本公司对文档中的所有内容不提供任何明示或暗示的保证，包括但不限于适销性、质量满意度、适合特定目的、不侵犯第三方权利等保证。

出口管制合规声明大华遵守适用的出口管制法律法规，并且贯彻执行与硬件、软件、技术的出口、再出口及转让相关的要求。

就本手册所描述的产品，请您全面理解并严格遵守国内外适用的出口管制法律法规。

关于本文档●产品请以实物为准，本文档仅供参考。

●本文档供多个型号产品做参考，每个产品的具体操作不一一例举，请用户根据实际产品自行对照操作。