机械英文专业翻译
- 格式:doc
- 大小:22.00 KB
- 文档页数:6
机械专业英文翻译 Company number:【WTUT-WT88Y-W8BBGB-BWYTT-19998】启动轴 starting axle 启动齿轮starting gear启动棘轮 starting ratchet wheel 复位弹簧 restoring, pull back spring弹簧座 spring seating 摩擦簧friction spring推力垫圈 thrust washer 轴挡圈axle bumper ring下料 filling 切断 cut 滚齿机 gear-hobbing machine剪料机 material-shearingmachine车床 lathe 拉床broaching machine垂直度 verticality, verticalextent 平行度 parallelism同心度 homocentricity位置度 position拉伤 pulling damage碰伤 bumping damage缺陷 deficiency严重缺陷 severe deficiency摩擦力 friction 扭距 twist滑动 glide 滚动 roll打滑 skid 脱不开 can’t seperate不复位 can’t restore 直径 diameterM值 = 跨棒距 test rod span公法线 common normal line 弹性elasticity频率特性 frequency characteristic误差 error响应 response 定位 allocation 机床夹具 jig 动力学 dynamic运动学 kinematic静力学 static分析力学 analyse mechanics拉伸 pulling压缩 hitting机床 machine tool刀具 cutter摩擦 friction联结 link传动 drive/transmission轴 shaft剪切 shear扭转 twist弯曲应力 bending stress三相交流电 three-phase AC磁路 magnetic circles变压器 transformer异步电动机 asynchronous motor几何形状 geometrical精度 precision正弦形的 sinusoid交流电路 AC circuit机械加工余量 machining allowance变形力 deforming force变形 deformation电路 circuit半导体元件 semiconductor element拉孔 broaching装配 assembling加工 machining液压 hydraulic pressure切线 tangent机电一体化 mechanotronics mechanical-electrical integration稳定性 stability介质 medium液压驱动泵 fluid clutch 液压泵 hydraulic pump阀门 valve失效 invalidation强度 intensity载荷 load应力 stress安全系数 safty factor可靠性 reliability螺纹 thread螺旋 helix键 spline销 pin滚动轴承 rolling bearing滑动轴承 sliding bearing弹簧 spring制动器 arrester brake十字结联轴节 crosshead联轴器 coupling链 chain皮带 strap精加工 finish machining粗加工 rough machining变速箱体 gearbox casing腐蚀 rust氧化 oxidation磨损 wear耐用度 durability机械制图Mechanical drawing投影 projection视图 view剖视图 profile chart标准件 standard component零件图 part drawing装配图 assembly drawing尺寸标注 size marking技术要求technical requirements刚度 rigidity内力 internal force位移 displacement截面 section疲劳极限 fatigue limit断裂 fracture塑性变形 plastic distortion脆性材料 brittleness material刚度准则 rigidity criterion垫圈 washer垫片 spacer直齿圆柱齿轮straight toothed spur gear斜齿圆柱齿轮helical-spur gear直齿锥齿轮straight bevel gear运动简图 kinematic sketch齿轮齿条 pinion and rack蜗杆蜗轮 worm and worm gear虚约束 passive constraint曲柄 crank摇杆 racker凸轮 cams反馈 feedback发生器 generator直流电源 DC electrical source 门电路 gate circuit外圆磨削 external grinding内圆磨削 internal grinding平面磨削 plane grinding变速箱 gearbox离合器 clutch绞孔 fraising绞刀 reamer螺纹加工 thread processing螺钉 screw铣削 mill铣刀 milling cutter功率 power工件 workpiece齿轮加工 gear mechining齿轮 gear主运动 main movement主运动方向direction of main movement进给方向 direction of feed进给运动 feed movement合成进给运动resultant movement of feed合成切削运动resultant movement of cutting合成切削运动方向 directionof resultant movement of cutting 切削深度 cutting depth前刀面 rake face刀尖 nose of tool前角 rake angle后角 clearance angle龙门刨削 planing主轴 spindle主轴箱 headstock卡盘 chuck加工中心 machining center车刀 lathe tool车床 lathe镗削 bore集成电路 integrate circuit挡板 orifice plate残余应力 residual stress套筒 sleeve扭力 torsion 冷加工 cold machining电动机 electromotor汽缸 cylinder过盈配合 interference fit热加工 hotwork摄像头 CCD camera倒角 rounding chamfer优化设计 optimal design工业造型设计industrial moulding design有限元 finite element滚齿 hobbing插齿 gear shaping伺服电机 actuating motor铣床 milling machine钻床 drill machine镗床 boring machine步进电机 stepper motor丝杠 screw rod导轨 lead rail组件 subassembly可编程序逻辑控制器Programmable LogicController PLC毛坯 rough桁架 truss轴线 axes逻辑电路 logic circuit触发器 flip-flop脉冲波形 pulse shape数模 digital analogy液压传动机构fluid drive mechanism机械零件 mechanical parts产品突出特点ProductHighlights特别优惠 special offersAssembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Pneumatic screw driver气动起子worktable 工作桌OOBA开箱检查fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet栈板barcode条码barcode scanner条码扫描器fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cosmetic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs. inch镑、英寸EMI gasket导电条front plate前板rear plate后板chassis 基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS电源电压接拉键sheet metal parts 冲件plastic parts塑胶件SOP制造作业程序material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线left fork叉车personnel resource department人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer |'plein|刨床miller铣床grinder磨床driller床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vice section superisor 副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skrpid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |' ksi'dein|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓name of a department部门名称administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单screwdriver holder起子插座pedal踩踏板stopper阻挡器flow board流水板hydraulic handjack油压板车forklift叉车pallet栈板glove(s)手套glove(s) with exposed fingers割手套missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a little bigger尺寸偏大(小)cosmetic defect外观不良slipped screwhead/slippery screw head螺丝滑头slipped screwhead/shippery screw thread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质qualified products, up-to-grade products良品defective products, not up-to-grade products不良品waste废料board看板feeder送料机sliding rack滑料架defective product box不良品箱die change 换模to fix a die装模to take apart a die拆模to repair a die修模packing material包材basket蝴蝶竺plastic basket胶筐isolating plate baffle plate; barricade隔板carton box纸箱to pull and stretch拉深to put material in place, to cut material, to input落料to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料transportation运输(be)qualfied, up to grade合格not up to grade, not qualified不合格material change, stock change材料变更feature change 特性变更evaluation评估prepare for, make preparations for 准备parameters参数rotating speed, revolution转速manufacture management制造管理abnormal handling异常处理production unit生产单位lots of production生产批量steel plate钢板roll material卷料manufacture procedure制程vocabulary for stamping冲压常词汇stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, block stop 定位块reset复位smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货to return delivenry to.to send delinery backto retrn of goods退货registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收to notice通知application form for purchase请购单consume, consumption消耗to fill in填写abrasion磨损die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die连续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder文件夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备waste materials废料plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸)draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号)shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板(顶板)top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块barreling 滚光加工 belling 压凸加工bending 弯曲加工 blanking 下料加工bulging 撑压加工 burring 冲缘加工cam die bending 凸轮弯曲加工caulking 合加工coining 压印加工 compressing 压缩加工compression bending 押弯曲加工crowning 凸面加工curl bending 卷边弯曲加工curling 卷曲加工cutting 切削加工 dinking 切断蕊骨double shearing 叠板裁断 drawing 引伸加工drawing with ironing 抽引光滑加工 embossing 浮花压制加工extrusion 挤制加工 filing 锉削加工fine blanking 精密下料加工 finish blanking 光制下料加工finishing 精整加工 flanging 凸缘加工folding 折边弯曲加工 folding 摺叠加工forming 成形加工 impact extrusion 冲击挤压加工indenting 压痕加工 ironing 引缩加工knurling 滚花 lock seaming 固定接合louvering 百叶窗板加工 marking 刻印加工necking 颈缩加工 notching 冲口加工parting 分断加工 piercing 冲孔加工progressive bending 连续弯曲加工 progressiveblanking 连续下料加工progressive drawing 连续引伸加工 progressiveforming 连续成形加工reaming 铰孔加工 restriking 二次精冲加工riveting 接加工 roll bending 滚筒弯曲加工roll finishing 滚压加工 rolling 压延加工roughing 粗加工 scrapless machining 无废料加工seaming 折弯重叠加工 shaving 缺口修整加工shearing 切断加工 sizing 精压加工/矫正加工slitting 割缝加工 spinning 卷边接staking 固 stamping 锻压加工swaging 挤锻压加工 trimming 整缘加工upsetting 锻粗加工 wiring 抽线加工冲压机械及周边关连用语back shaft 支撑轴 blank determination 胚料展开bottom slide press 下传动式压力机 board drophammer 板落锤brake 煞车 buckle 剥砂面camlachie cramp 铸包 casting on flat 合chamotte sand 烧磨砂 charging hopper 加料漏斗clearance 间隙 closed-die forging 合模锻造clump 夹紧 clutch 离合器clutch brake 离合器制动器 clutch boss 离合器轮壳clutch lining 离合器覆盖 coil car 带卷升降运输机coil cradle 卷材进料装置 coil reel stand 钢材卷料架column 圆柱 connection screw 连杆调节螺钉core compound 砂心黏结剂 counter blow hammer 对击锻锤cradle 送料架 crank 曲柄轴crankless 无曲柄式 cross crank 横向曲轴cushion 缓冲 depression 外缩凹孔dial feed 分度送料 die approach 模口角度die assembly 合模 die cushion 模具缓冲垫die height 冲压闭合高度 die life 模具寿命die opening 母模逃孔 die spotting press 调整冲模用压力机double crank press 双曲柄轴冲床 draght angle 逃料倾斜角edging 边锻伸 embedded core 加装砂心feed length 送料长度 feed level 送料高度filling core 埋入砂心 filling in 填砂film play 液面花纹 fine blanking press 精密下料冲床forging roll 辊锻机 finishing slag 炼後熔渣fly wheel 飞轮 fly wheel brake 飞轮制动器foot press 脚踏冲床 formboard 进模口板frame 床身机架 friction 摩擦friction brake 摩擦煞车 gap shear 凹口剪床gear 齿轮 gib 滑块引导部gripper 夹具 gripper feed 夹持进料gripper feeder 夹紧传送装置 hammer 槌机hand press 手动冲床 hand rack pinion press 手动齿轮齿条式冲床hand screw press 手动螺旋式冲床 hopper feed 料斗送料idle stage 空站 inching 微调尺寸isothermal forging 恒温锻造 key clutch 键槽离合器knockout 脱模装置 knuckle mechanic 转向机构land 模具直线刀面部 level 水平loader 供料器 unloader 卸料机loop controller 闭回路控制器 lower die 下模micro inching device 微寸动装置 microinching equipment 微动装置motor 马达 moving bolster 活动工作台notching press 冲缺口压力机 opening 排料逃孔overload protection device 防超载装置 pinch roll 导正滚轮pinion 小齿轮 pitch 节距pressfit 压入 progressive 连续送料pusher feed 推杆式送料 pusher feeder 料片押片装置quick die change system 快速换模系统 regrinding 再次研磨releasing 松释动作 reversedblanking 反转下料robot 机器人 roll formingmachine 辊轧成形roll forming machine 辊轧成形机roll release 脱辊roller feed 辊式送料 roller leveler辊式矫直机rotary bender 卷弯成形机 safetyguard 安全保护装置scrap cutter 废料切刀 scrap press废料冲床seamless forging 无缝锻造separate 分离shave 崩砂 shear angle 剪角sheet loader 薄板装料机 shot 单行程工作shrinkage fit 收缩配合 shutheight 闭合高度sieve mesh 筛孔 sintering of sand铸砂烧贴slide balancer 滑动平衡器 slughole 逃料孔spin forming machine 旋压成形机 spotting 合模stack feeder 堆叠拨送料机stickness 黏模性straight side frame 冲床侧板stretcher leveler 拉伸矫直机strip feeder 料材送料装置stripping pressure 弹出压力stroke 冲程 take out device 取料装置toggle press 肘杆式压力机transfer 传送transfer feed 连续自动送料装置turrent punch press 转塔冲床two speed clutch 双速离合器uncoiler 闭卷送料机unloader 卸载机 vibration feeder振动送料机wiring press 嵌线卷边机业务与贸易关连用语accept order 接受订货 account 帐户after service 售后服务 amendment 修正annual sales 年销售额 at sight 见票即付balance 余额 bank draft 汇票bargain goods 廉价品 batch 批次bid 出价 bid sales 投标买卖bill of landing 提单 bills receivable 应收票据brand 品牌 bulk cargo 散装货business transaction 商业交易 buyer 买方carbon copy 打字副本 cargo collection 揽货carton 纸箱 cash in advance 预付现金catalogue 型录 cheque 支票CLF 运费保险费在内价格 claim 索赔clearance goods 清仓品 commision 佣金commission 批发商 complain 抱怨container 货柜 correspondence bank 往来银行cost 成本 cost and freight; C&F 含运费价格custom broker 报关行 customer 客户D/A 承兑交单 D/P 付款交单deferred payment 分期付款 deferred shipment 分期装运delivery on spot 当场交货 delivery time 交期delivery order 交货单 discount 折扣discount on draft 贴现 documentary draft 跟单汇票down payment 订金 enclosure 附件endorsement 背书 enquete 调查exhibition 展览会 export 出口factory visiy 工厂参观 favourable price 合宜价格foreign exchange 外汇 free on board 船上交货价idea price 希望价格 import 进口Japanese Industrial 日本工业规格 invoice 发票L/C 信用状 margin 利润market 市价 net weight 净重no payment 拒绝付款 odd item 零头offer 报价 open account 交互计算order 订单 over looked 疏漏packing 包装 pamphlet 小册子partial shipment 分批装船 patent 专利paying price 合算价格 payment method 付款方式port of destination 目地港 port of trans-shipment转口港price 价格 price decending 减价price rising 涨价 procurement 采办prompt delivery 即时交货 purchase 购入purchasing agent 采购代理商 quotation 报价单rebate 回扣 reference 查询remittance 汇款 repeat order 追加订货request letter 请求函 rumor 风评second hand goods 二手货 shipper 货主shipping 装船 shipping mark 麦头shipment 出货 sold out 卖完sole agent 总代理商 special discount 特别折扣specification 规格 sample order 指样订货standing 信用情形 storage charge 仓租subcontract 外包 subject to final confirmation 有待确认之报价supplier 供应商 T/T 电汇tie-in sale 搭售 trade fair 商展会trans-shipment 转运 transferred 已转运wharf 码头。
机械术语翻译变速齿轮change gear ; change wheel 回火tempering变位齿轮modified gear 磨粒abrasive grain变位系数modification coefficient 砂轮grinding wheel标准齿轮standard gear 刀具cutter标准直齿轮standard spur gear 轴shaft金属切削metal cutting 频率特性frequency characteristic 调质hardening and tempering 响应response结合剂bonding agent 机床夹具jig机床machine tool 拉伸pulling摩擦friction 静力学static传动drive/transmission 压缩hitting弹性elasticity误差error定位allocation动力学dynamic运动学kinematic分析力学analyse mechanics剪切shear扭转twist弯曲应力bending stress强度intensity异步电动机asynchronous motor几何形状geometrical精度precision机械加工余量machining allowance变形力deforming force变形deformation应力stress硬度rigidity热处理heat treatment退火anneal正火normalizing脱碳decarburization渗碳carburization外圆磨削external grinding内圆磨削internal grinding平面磨削plane grinding变速箱gearbox离合器clutch绞孔fraising绞刀reamer螺纹加工thread processing螺钉screw铣削mill铣刀milling cutter功率power工件workpiece齿轮加工gear mechining齿轮gear主运动main movement主运动方向direction of main movement进给方向direction of feed进给运动feed movement合成进给运动resultant movement of feed合成切削运动resultant movement of cutting合成切削运动方向direction of resultant movement of cutting 切削深度cutting depth前刀面rake face刀尖nose of tool前角rake angle后角clearance angle龙门刨削planing主轴spindle主轴箱headstock卡盘chuck加工中心machining center车刀lathe tool车床lathe钻削镗削bore车削turning磨床grinder基准benchmark钳工locksmith锻forge压模stamping焊weld拉床broaching machine拉孔broaching装配assembling铸造found流体动力学fluid dynamics流体力学fluid mechanics加工machining液压hydraulic pressure切线tangent机电一体化mechanotronics mechanical-electrical integration 气压air pressure pneumatic pressure稳定性stability介质medium液压驱动泵fluid clutch液压泵hydraulic pump阀门valve失效invalidation强度intensity载荷load应力stress安全系数safty factor可靠性reliability螺纹thread螺旋helix键spline销pin滚动轴承rolling bearing残余应力residual stress套筒sleeve扭力torsion冷加工cold machining电动机electromotor汽缸cylinder过盈配合interference fit热加工hotwork摄像头CCD camera倒角rounding chamfer优化设计optimal design工业造型设计industrial moulding design 有限元finite element齿hobbing插齿gear shaping伺服电机actuating motor铣床milling machine钻床drill machine镗床boring machine。
如有你有帮助,请购买下载,谢谢!阿基米德蜗杆 Archimedes worm安全系数 safety factor; factor of safety安全载荷 safe load凹面、凹度 concavity扳手 wrench板簧 flat leaf spring半圆键 woodruff key变形 deformation摆杆 oscillating bar摆动从动件 oscillating follower摆动从动件凸轮机构 cam with oscillating follower 摆动导杆机构 oscillating guide-bar mechanism摆线齿轮 cycloidal gear摆线齿形 cycloidal tooth profile摆线运动规律 cycloidal motion摆线针轮 cycloidal-pin wheel包角 angle of contact保持架 cage背对背安装 back-to-back arrangement背锥 back cone ;normal cone背锥角 back angle背锥距 back cone distance比例尺 scale比热容 specific heat capacity闭式链 closed kinematic chain闭链机构 closed chain mechanism臂部 arm变频器 frequency converters变频调速 frequency control of motor speed变速 speed change变速齿轮 change gear ; change wheel变位齿轮 modified gear变位系数 modification coefficient标准齿轮 standard gear标准直齿轮 standard spur gear表面质量系数 superficial mass factor表面传热系数 surface coefficient of heat transfer 表面粗糙度 surface roughness并联式组合 combination in parallel并联机构 parallel mechanism并联组合机构 parallel combined mechanism并行工程 concurrent engineering并行设计 concurred design, CD不平衡相位 phase angle of unbalance不平衡 imbalance (or unbalance)不平衡量 amount of unbalance 不完全齿轮机构 intermittent gearing波发生器 wave generator波数 number of waves补偿 compensation参数化设计 parameterization design, PD残余应力 residual stress操纵及控制装置 operation control device槽轮 Geneva wheel槽轮机构 Geneva mechanism ;Maltese cross槽数 Geneva numerate槽凸轮 groove cam侧隙 backlash差动轮系 differential gear train差动螺旋机构 differential screw mechanism差速器 differential常用机构 conventional mechanism; mechanism in common use 车床 lathe承载量系数 bearing capacity factor承载能力 bearing capacity成对安装 paired mounting尺寸系列 dimension series齿槽 tooth space齿槽宽 spacewidth齿侧间隙 backlash齿顶高 addendum齿顶圆 addendum circle齿根高 dedendum齿根圆 dedendum circle齿厚 tooth thickness齿距 circular pitch齿宽 face width齿廓 tooth profile齿廓曲线 tooth curve齿轮 gear齿轮变速箱 speed-changing gear boxes齿轮齿条机构 pinion and rack齿轮插刀 pinion cutter; pinion-shaped shaper cutter齿轮滚刀 hob ,hobbing cutter齿轮机构 gear齿轮轮坯 blank齿轮传动系 pinion unit齿轮联轴器 gear coupling齿条传动 rack gear齿数 tooth number齿数比 gear ratio齿条 rack如有你有帮助,请购买下载,谢谢!齿条插刀 rack cutter; rack-shaped shaper cutter齿形链、无声链 silent chain齿形系数 form factor齿式棘轮机构 tooth ratchet mechanism插齿机 gear shaper重合点 coincident points重合度 contact ratio冲床 punch传动比 transmission ratio, speed ratio传动装置 gearing; transmission gear传动系统 driven system传动角 transmission angle传动轴 transmission shaft串联式组合 combination in series串联式组合机构 series combined mechanism串级调速 cascade speed control创新 innovation ; creation创新设计 creation design垂直载荷、法向载荷 normal load唇形橡胶密封 lip rubber seal磁流体轴承 magnetic fluid bearing从动带轮 driven pulley从动件 driven link, follower从动件平底宽度 width of flat-face从动件停歇 follower dwell从动件运动规律 follower motion从动轮 driven gear粗线 bold line粗牙螺纹 coarse thread大齿轮 gear wheel打包机 packer打滑 slipping带传动 belt driving带轮 belt pulley带式制动器 band brake单列轴承 single row bearing单向推力轴承 single-direction thrust bearing单万向联轴节 single universal joint单位矢量 unit vector当量齿轮 equivalent spur gear; virtual gear当量齿数 equivalent teeth number; virtual number of teeth 当量摩擦系数 equivalent coefficient of friction当量载荷 equivalent load刀具 cutter导数 derivative倒角 chamfer 导热性 conduction of heat导程 lead导程角 lead angle等加等减速运动规律 parabolic motion; constant acceleration and deceleration motion等速运动规律 uniform motion; constant velocity motion等径凸轮 conjugate yoke radial cam等宽凸轮 constant-breadth cam等效构件 equivalent link等效力 equivalent force等效力矩 equivalent moment of force等效量 equivalent等效质量 equivalent mass等效转动惯量 equivalent moment of inertia等效动力学模型 dynamically equivalent model底座 chassis低副 lower pair点划线 chain dotted line(疲劳)点蚀 pitting垫圈 gasket垫片密封 gasket seal碟形弹簧 belleville spring顶隙 bottom clearance定轴轮系 ordinary gear train; gear train with fixed axes动力学 dynamics动密封 kinematical seal动能 dynamic energy动力粘度 dynamic viscosity动力润滑 dynamic lubrication动平衡 dynamic balance动平衡机 dynamic balancing machine动态特性 dynamic characteristics动态分析设计 dynamic analysis design动压力 dynamic reaction动载荷 dynamic load端面 transverse plane端面参数 transverse parameters端面齿距 transverse circular pitch端面齿廓 transverse tooth profile端面重合度 transverse contact ratio端面模数 transverse module端面压力角 transverse pressure angle锻造 forge对称循环应力 symmetry circulating stress对心滚子从动件 radial (or in-line ) roller follower对心直动从动件 radial (or in-line ) translating follower如有你有帮助,请购买下载,谢谢!对心移动从动件 radial reciprocating follower对心曲柄滑块机构 in-line slider-crank (or crank-slider) mechanism 多列轴承 multi-row bearing多楔带 poly V-belt多项式运动规律 polynomial motion多质量转子 rotor with several masses惰轮 idle gear额定寿命 rating life额定载荷 load ratingII 级杆组 dyad发生线 generating line发生面 generating plane法面 normal plane法面参数 normal parameters法面齿距 normal circular pitch法面模数 normal module法面压力角 normal pressure angle法向齿距 normal pitch法向齿廓 normal tooth profile法向直廓蜗杆 straight sided normal worm法向力 normal force反馈式组合 feedback combining反向运动学 inverse ( or backward) kinematics反转法 kinematic inversion反正切 Arctan范成法 generating cutting仿形法 form cutting方案设计、概念设计 concept design, CD防振装置 shockproof device飞轮 flywheel飞轮矩 moment of flywheel非标准齿轮 nonstandard gear非接触式密封 non-contact seal非周期性速度波动 aperiodic speed fluctuation非圆齿轮 non-circular gear粉末合金 powder metallurgy分度线 reference line; standard pitch line分度圆 reference circle; standard (cutting) pitch circle分度圆柱导程角 lead angle at reference cylinder分度圆柱螺旋角 helix angle at reference cylinder分母 denominator分子 numerator分度圆锥 reference cone; standard pitch cone分析法 analytical method封闭差动轮系 planetary differential复合铰链 compound hinge 复合式组合 compound combining复合轮系 compound (or combined) gear train 复合平带 compound flat belt复合应力 combined stress复式螺旋机构 Compound screw mechanism 复杂机构 complex mechanism杆组 Assur group干涉 interference刚度系数 stiffness coefficient刚轮 rigid circular spline钢丝软轴 wire soft shaft刚体导引机构 body guidance mechanism刚性冲击 rigid impulse (shock)刚性转子 rigid rotor刚性轴承 rigid bearing刚性联轴器 rigid coupling高度系列 height series高速带 high speed belt高副 higher pair格拉晓夫定理 Grashoff`s law根切 undercutting公称直径 nominal diameter高度系列 height series功 work工况系数 application factor工艺设计 technological design工作循环图 working cycle diagram工作机构 operation mechanism工作载荷 external loads工作空间 working space工作应力 working stress工作阻力 effective resistance工作阻力矩 effective resistance moment公法线 common normal line公共约束 general constraint公制齿轮 metric gears功率 power功能分析设计 function analyses design共轭齿廓 conjugate profiles共轭凸轮 conjugate cam构件 link鼓风机 blower固定构件 fixed link; frame固体润滑剂 solid lubricant关节型操作器 jointed manipulator惯性力 inertia force如有你有帮助,请购买下载,谢谢!惯性力矩 moment of inertia ,shaking moment惯性力平衡 balance of shaking force惯性力完全平衡 full balance of shaking force惯性力部分平衡 partial balance of shaking force 惯性主矩 resultant moment of inertia惯性主失 resultant vector of inertia冠轮 crown gear广义机构 generation mechanism广义坐标 generalized coordinate轨迹生成 path generation轨迹发生器 path generator滚刀 hob滚道 raceway滚动体 rolling element滚动轴承 rolling bearing滚动轴承代号 rolling bearing identification code 滚针 needle roller滚针轴承 needle roller bearing滚子 roller滚子轴承 roller bearing滚子半径 radius of roller滚子从动件 roller follower滚子链 roller chain滚子链联轴器 double roller chain coupling滚珠丝杆 ball screw滚柱式单向超越离合器 roller clutch过度切割 undercutting函数发生器 function generator函数生成 function generation含油轴承 oil bearing耗油量 oil consumption耗油量系数 oil consumption factor赫兹公式 H. Hertz equation合成弯矩 resultant bending moment合力 resultant force合力矩 resultant moment of force黑箱 black box横坐标 abscissa互换性齿轮 interchangeable gears花键 spline滑键、导键 feather key滑动轴承 sliding bearing滑动率 sliding ratio滑块 slider环面蜗杆 toroid helicoids worm环形弹簧 annular spring 缓冲装置 shocks; shock-absorber灰铸铁 grey cast iron回程 return回转体平衡 balance of rotors混合轮系 compound gear train积分 integrate机电一体化系统设计 mechanical-electrical integration system design 机构 mechanism机构分析 analysis of mechanism机构平衡 balance of mechanism机构学 mechanism机构运动设计 kinematic design of mechanism机构运动简图 kinematic sketch of mechanism机构综合 synthesis of mechanism机构组成 constitution of mechanism机架 frame, fixed link机架变换 kinematic inversion机器 machine机器人 robot机器人操作器 manipulator机器人学 robotics技术过程 technique process技术经济评价 technical and economic evaluation技术系统 technique system机械 machinery机械创新设计 mechanical creation design, MCD机械系统设计 mechanical system design, MSD机械动力分析 dynamic analysis of machinery机械动力设计 dynamic design of machinery机械动力学 dynamics of machinery机械的现代设计 modern machine design机械系统 mechanical system机械利益 mechanical advantage机械平衡 balance of machinery机械手 manipulator机械设计 machine design; mechanical design机械特性 mechanical behavior机械调速 mechanical speed governors机械效率 mechanical efficiency机械原理 theory of machines and mechanisms机械运转不均匀系数 coefficient of speed fluctuation机械无级变速 mechanical stepless speed changes基础机构 fundamental mechanism基本额定寿命 basic rating life基于实例设计 case-based design,CBD基圆 base circle如有你有帮助,请购买下载,谢谢!基圆半径 radius of base circle基圆齿距 base pitch基圆压力角 pressure angle of base circle基圆柱 base cylinder基圆锥 base cone急回机构 quick-return mechanism急回特性 quick-return characteristics急回系数 advance-to return-time ratio急回运动 quick-return motion棘轮 ratchet棘轮机构 ratchet mechanism棘爪 pawl极限位置 extreme (or limiting) position极位夹角 crank angle between extreme (or limiting) positions计算机辅助设计 computer aided design, CAD计算机辅助制造 computer aided manufacturing, CAM计算机集成制造系统 computer integrated manufacturing system, CIMS计算力矩 factored moment; calculation moment计算弯矩 calculated bending moment加权系数 weighting efficient加速度 acceleration加速度分析 acceleration analysis加速度曲线 acceleration diagram尖点 pointing; cusp尖底从动件 knife-edge follower间隙 backlash间歇运动机构 intermittent motion mechanism减速比 reduction ratio减速齿轮、减速装置 reduction gear减速器 speed reducer减摩性 anti-friction quality渐开螺旋面 involute helicoid渐开线 involute渐开线齿廓 involute profile渐开线齿轮 involute gear渐开线发生线 generating line of involute渐开线方程 involute equation渐开线函数 involute function渐开线蜗杆 involute worm渐开线压力角 pressure angle of involute渐开线花键 involute spline简谐运动 simple harmonic motion键 key键槽 keyway交变应力 repeated stress 交变载荷 repeated fluctuating load交叉带传动 cross-belt drive交错轴斜齿轮 crossed helical gears胶合 scoring角加速度 angular acceleration角速度 angular velocity角速比 angular velocity ratio角接触球轴承 angular contact ball bearing角接触推力轴承 angular contact thrust bearing角接触向心轴承 angular contact radial bearing角接触轴承 angular contact bearing铰链、枢纽 hinge校正平面 correcting plane接触应力 contact stress接触式密封 contact seal阶梯轴 multi-diameter shaft结构 structure结构设计 structural design截面 section节点 pitch point节距 circular pitch; pitch of teeth节线 pitch line节圆 pitch circle节圆齿厚 thickness on pitch circle节圆直径 pitch diameter节圆锥 pitch cone节圆锥角 pitch cone angle解析设计 analytical design紧边 tight-side紧固件 fastener径节 diametral pitch径向 radial direction径向当量动载荷 dynamic equivalent radial load径向当量静载荷 static equivalent radial load径向基本额定动载荷 basic dynamic radial load rating 径向基本额定静载荷 basic static radial load tating径向接触轴承 radial contact bearing径向平面 radial plane径向游隙 radial internal clearance径向载荷 radial load径向载荷系数 radial load factor径向间隙 clearance静力 static force静平衡 static balance静载荷 static load静密封 static seal如有你有帮助,请购买下载,谢谢!局部自由度 passive degree of freedom矩阵 matrix矩形螺纹 square threaded form锯齿形螺纹 buttress thread form矩形牙嵌式离合器 square-jaw positive-contact clutch绝对尺寸系数 absolute dimensional factor绝对运动 absolute motion绝对速度 absolute velocity均衡装置 load balancing mechanism抗压强度 compression strength开口传动 open-belt drive开式链 open kinematic chain开链机构 open chain mechanism可靠度 degree of reliability可靠性 reliability可靠性设计 reliability design, RD空气弹簧 air spring空间机构 spatial mechanism空间连杆机构 spatial linkage空间凸轮机构 spatial cam空间运动副 spatial kinematic pair空间运动链 spatial kinematic chain空转 idle宽度系列 width series框图 block diagram雷诺方程Reynolds‘s equation离心力 centrifugal force离心应力 centrifugal stress离合器 clutch离心密封 centrifugal seal理论廓线 pitch curve理论啮合线 theoretical line of action隶属度 membership力 force力多边形 force polygon力封闭型凸轮机构 force-drive (or force-closed) cam mechanism 力矩 moment力平衡 equilibrium力偶 couple力偶矩 moment of couple连杆 connecting rod, coupler连杆机构 linkage连杆曲线 coupler-curve连心线 line of centers链 chain链传动装置 chain gearing 链轮 sprocket ; sprocket-wheel ; sprocket gear ; chain wheel 联组V 带 tight-up V belt联轴器 coupling ; shaft coupling两维凸轮 two-dimensional cam临界转速 critical speed六杆机构 six-bar linkage龙门刨床 double Haas planer轮坯 blank轮系 gear train螺杆 screw螺距 thread pitch螺母 screw nut螺旋锥齿轮 helical bevel gear螺钉 screws螺栓 bolts螺纹导程 lead螺纹效率 screw efficiency螺旋传动 power screw螺旋密封 spiral seal螺纹 thread (of a screw)螺旋副 helical pair螺旋机构 screw mechanism螺旋角 helix angle螺旋线 helix ,helical line绿色设计 green design ; design for environment马耳他机构 Geneva wheel ; Geneva gear马耳他十字 Maltese cross脉动无级变速 pulsating stepless speed changes脉动循环应力 fluctuating circulating stress脉动载荷 fluctuating load铆钉 rivet迷宫密封 labyrinth seal密封 seal密封带 seal belt密封胶 seal gum密封元件 potted component密封装置 sealing arrangement面对面安装 face-to-face arrangement面向产品生命周期设计 design for product`s life cycle, DPLC 名义应力、公称应力 nominal stress模块化设计 modular design, MD模块式传动系统 modular system模幅箱 morphology box模糊集 fuzzy set模糊评价 fuzzy evaluation模数 module如有你有帮助,请购买下载,谢谢!摩擦 friction摩擦角 friction angle摩擦力 friction force摩擦学设计 tribology design, TD摩擦阻力 frictional resistance摩擦力矩 friction moment摩擦系数 coefficient of friction摩擦圆 friction circle磨损 abrasion ;wear; scratching末端执行器 end-effector目标函数 objective function耐腐蚀性 corrosion resistance耐磨性 wear resistance挠性机构 mechanism with flexible elements 挠性转子 flexible rotor内齿轮 internal gear内齿圈 ring gear内力 internal force内圈 inner ring能量 energy能量指示图 viscosity逆时针 counterclockwise (or anticlockwise) 啮出 engaging-out啮合 engagement, mesh, gearing啮合点 contact points啮合角 working pressure angle啮合线 line of action啮合线长度 length of line of action啮入 engaging-in牛头刨床 shaper凝固点 freezing point; solidifying point扭转应力 torsion stress扭矩 moment of torque扭簧 helical torsion spring诺模图 NomogramO 形密封圈密封 O ring seal盘形凸轮 disk cam盘形转子 disk-like rotor抛物线运动 parabolic motion疲劳极限 fatigue limit疲劳强度 fatigue strength偏置式 offset偏( 心) 距 offset distance偏心率 eccentricity ratio偏心质量 eccentric mass偏距圆 offset circle 偏心盘 eccentric偏置滚子从动件 offset roller follower偏置尖底从动件 offset knife-edge follower偏置曲柄滑块机构 offset slider-crank mechanism拼接 matching评价与决策 evaluation and decision频率 frequency平带 flat belt平带传动 flat belt driving平底从动件 flat-face follower平底宽度 face width平分线 bisector平均应力 average stress平均中径 mean screw diameter平均速度 average velocity平衡 balance平衡机 balancing machine平衡品质 balancing quality平衡平面 correcting plane平衡质量 balancing mass平衡重 counterweight平衡转速 balancing speed平面副 planar pair, flat pair平面机构 planar mechanism平面运动副 planar kinematic pair平面连杆机构 planar linkage平面凸轮 planar cam平面凸轮机构 planar cam mechanism平面轴斜齿轮 parallel helical gears普通平键 parallel key其他常用机构 other mechanism in common use起动阶段 starting period启动力矩 starting torque气动机构 pneumatic mechanism奇异位置 singular position起始啮合点 initial contact , beginning of contact气体轴承 gas bearing千斤顶 jack嵌入键 sunk key强迫振动 forced vibration切齿深度 depth of cut曲柄 crank曲柄存在条件 Grashoff`s law曲柄导杆机构 crank shaper (guide-bar) mechanism曲柄滑块机构 slider-crank (or crank-slider) mechanism 曲柄摇杆机构 crank-rocker mechanism如有你有帮助,请购买下载,谢谢!曲齿锥齿轮 spiral bevel gear曲率 curvature曲率半径 radius of curvature曲面从动件 curved-shoe follower曲线拼接 curve matching曲线运动 curvilinear motion曲轴 crank shaft驱动力 driving force驱动力矩 driving moment (torque)全齿高 whole depth权重集 weight sets球 ball球面滚子 convex roller球轴承 ball bearing球面副 spheric pair球面渐开线 spherical involute球面运动 spherical motion球销副 sphere-pin pair球坐标操作器 polar coordinate manipulator燃点 spontaneous ignition热平衡 heat balance; thermal equilibrium人字齿轮 herringbone gear冗余自由度 redundant degree of freedom柔轮 flexspline柔性冲击 flexible impulse; soft shock柔性制造系统 flexible manufacturing system; FMS柔性自动化 flexible automation润滑油膜 lubricant film润滑装置 lubrication device润滑 lubrication润滑剂 lubricant三角形花键 serration spline三角形螺纹 V thread screw三维凸轮 three-dimensional cam三心定理 Kennedy`s theorem砂轮越程槽 grinding wheel groove砂漏 hour-glass少齿差行星传动 planetary drive with small teeth difference 设计方法学 design methodology设计变量 design variable设计约束 design constraints深沟球轴承 deep groove ball bearing生产阻力 productive resistance升程 rise升距 lift实际廓线 cam profile 十字滑块联轴器double slider coupling; Oldham‘s coupling 矢量 vector输出功 output work输出构件 output link输出机构 output mechanism输出力矩 output torque输出轴 output shaft输入构件 input link数学模型 mathematic model实际啮合线 actual line of action双滑块机构 double-slider mechanism, ellipsograph双曲柄机构 double crank mechanism双曲面齿轮 hyperboloid gear双头螺柱 studs双万向联轴节 constant-velocity (or double) universal joint 双摇杆机构 double rocker mechanism双转块机构 Oldham coupling双列轴承 double row bearing双向推力轴承 double-direction thrust bearing松边 slack-side顺时针 clockwise瞬心 instantaneous center死点 dead point四杆机构 four-bar linkage速度 velocity速度不均匀( 波动) 系数 coefficient of speed fluctuation 速度波动 speed fluctuation速度曲线 velocity diagram速度瞬心 instantaneous center of velocity塔轮 step pulley踏板 pedal台钳、虎钳 vice太阳轮 sun gear弹性滑动 elasticity sliding motion弹性联轴器 elastic coupling ; flexible coupling弹性套柱销联轴器 rubber-cushioned sleeve bearing coupling 套筒 sleeve梯形螺纹 acme thread form特殊运动链 special kinematic chain特性 characteristics替代机构 equivalent mechanism调节 modulation, regulation调心滚子轴承 self-aligning roller bearing调心球轴承 self-aligning ball bearing调心轴承 self-aligning bearing调速 speed governing如有你有帮助,请购买下载,谢谢!调速电动机 adjustable speed motors调速系统 speed control system调压调速 variable voltage control调速器 regulator, governor铁磁流体密封 ferrofluid seal停车阶段 stopping phase停歇 dwell同步带 synchronous belt同步带传动 synchronous belt drive凸的,凸面体 convex凸轮 cam凸轮倒置机构 inverse cam mechanism凸轮机构 cam , cam mechanism凸轮廓线 cam profile凸轮廓线绘制 layout of cam profile凸轮理论廓线 pitch curve凸缘联轴器 flange coupling图册、图谱 atlas图解法 graphical method推程 rise推力球轴承 thrust ball bearing推力轴承 thrust bearing退刀槽 tool withdrawal groove退火 anneal陀螺仪 gyroscopeV 带 V belt外力 external force外圈 outer ring外形尺寸 boundary dimension万向联轴器 Hooks coupling ; universal coupling 外齿轮 external gear弯曲应力 beading stress弯矩 bending moment腕部 wrist往复移动 reciprocating motion往复式密封 reciprocating seal网上设计 on-net design, OND微动螺旋机构 differential screw mechanism位移 displacement位移曲线 displacement diagram位姿 pose , position and orientation稳定运转阶段 steady motion period稳健设计 robust design蜗杆 worm蜗杆传动机构 worm gearing蜗杆头数 number of threads 蜗杆直径系数 diametral quotient蜗杆蜗轮机构 worm and worm gear蜗杆形凸轮步进机构 worm cam interval mechanism蜗杆旋向 hands of worm蜗轮 worm gear涡圈形盘簧 power spring无级变速装置 stepless speed changes devices无穷大 infinite系杆 crank arm, planet carrier现场平衡 field balancing向心轴承 radial bearing向心力 centrifugal force相对速度 relative velocity相对运动 relative motion相对间隙 relative gap象限 quadrant橡皮泥 plasticine细牙螺纹 fine threads销 pin消耗 consumption小齿轮 pinion小径 minor diameter橡胶弹簧 balata spring修正梯形加速度运动规律 modified trapezoidal acceleration motion 修正正弦加速度运动规律 modified sine acceleration motion斜齿圆柱齿轮 helical gear斜键、钩头楔键 taper key泄漏 leakage谐波齿轮 harmonic gear谐波传动 harmonic driving谐波发生器 harmonic generator斜齿轮的当量直齿轮 equivalent spur gear of the helical gear心轴 spindle行程速度变化系数 coefficient of travel speed variation行程速比系数 advance-to return-time ratio行星齿轮装置 planetary transmission行星轮 planet gear行星轮变速装置 planetary speed changing devices行星轮系 planetary gear train形封闭凸轮机构 positive-drive (or form-closed) cam mechanism虚拟现实 virtual reality虚拟现实技术 virtual reality technology, VRT虚拟现实设计 virtual reality design, VRD虚约束 redundant (or passive) constraint许用不平衡量 allowable amount of unbalance许用压力角 allowable pressure angle如有你有帮助,请购买下载,谢谢!许用应力 allowable stress; permissible stress悬臂结构 cantilever structure悬臂梁 cantilever beam循环功率流 circulating power load旋转力矩 running torque旋转式密封 rotating seal旋转运动 rotary motion选型 type selection压力 pressure压力中心 center of pressure压缩机 compressor压应力 compressive stress压力角 pressure angle牙嵌式联轴器 jaw (teeth) positive-contact coupling雅可比矩阵 Jacobi matrix摇杆 rocker液力传动 hydrodynamic drive液力耦合器 hydraulic couplers液体弹簧 liquid spring液压无级变速 hydraulic stepless speed changes液压机构 hydraulic mechanism一般化运动链 generalized kinematic chain移动从动件 reciprocating follower移动副 prismatic pair, sliding pair移动关节 prismatic joint移动凸轮 wedge cam盈亏功 increment or decrement work应力幅 stress amplitude应力集中 stress concentration应力集中系数 factor of stress concentration应力图 stress diagram应力—应变图 stress-strain diagram优化设计 optimal design油杯 oil bottle油壶 oil can油沟密封 oily ditch seal有害阻力 useless resistance有益阻力 useful resistance有效拉力 effective tension有效圆周力 effective circle force有害阻力 detrimental resistance余弦加速度运动 cosine acceleration (or simple harmonic) motion 预紧力 preload原动机 primer mover圆带 round belt圆带传动 round belt drive 圆弧齿厚 circular thickness圆弧圆柱蜗杆 hollow flank worm圆角半径 fillet radius圆盘摩擦离合器 disc friction clutch圆盘制动器 disc brake原动机 prime mover原始机构 original mechanism圆形齿轮 circular gear圆柱滚子 cylindrical roller圆柱滚子轴承 cylindrical roller bearing圆柱副 cylindric pair圆柱式凸轮步进运动机构 barrel (cylindric) cam圆柱螺旋拉伸弹簧 cylindroid helical-coil extension spring圆柱螺旋扭转弹簧 cylindroid helical-coil torsion spring圆柱螺旋压缩弹簧 cylindroid helical-coil compression spring 圆柱凸轮 cylindrical cam圆柱蜗杆 cylindrical worm圆柱坐标操作器 cylindrical coordinate manipulator圆锥螺旋扭转弹簧 conoid helical-coil compression spring圆锥滚子 tapered roller圆锥滚子轴承 tapered roller bearing圆锥齿轮机构 bevel gears圆锥角 cone angle原动件 driving link约束 constraint约束条件 constraint condition约束反力 constraining force跃度 jerk跃度曲线 jerk diagram运动倒置 kinematic inversion运动方案设计 kinematic precept design运动分析 kinematic analysis运动副 kinematic pair运动构件 moving link运动简图 kinematic sketch运动链 kinematic chain运动失真 undercutting运动设计 kinematic design运动周期 cycle of motion运动综合 kinematic synthesis运转不均匀系数 coefficient of velocity fluctuation运动粘度 kenematic viscosity载荷 load载荷—变形曲线 load—deformation curve载荷—变形图 load—deformation diagram窄V 带 narrow V belt如有你有帮助,请购买下载,谢谢!毡圈密封 felt ring seal展成法 generating张紧力 tension张紧轮 tension pulley振动 vibration振动力矩 shaking couple振动频率 frequency of vibration振幅 amplitude of vibration正切机构 tangent mechanism正向运动学 direct (forward) kinematics正弦机构 sine generator, scotch yoke织布机 loom正应力、法向应力 normal stress制动器 brake直齿圆柱齿轮 spur gear直齿锥齿轮 straight bevel gear直角三角形 right triangle直角坐标操作器 Cartesian coordinate manipulator 直径系数 diametral quotient直径系列 diameter series直廓环面蜗杆 hindley worm直线运动 linear motion直轴 straight shaft质量 mass质心 center of mass执行构件 executive link; working link质径积 mass-radius product智能化设计 intelligent design, ID中间平面 mid-plane中心距 center distance中心距变动 center distance change中心轮 central gear中径 mean diameter终止啮合点 final contact, end of contact周节 pitch周期性速度波动 periodic speed fluctuation周转轮系 epicyclic gear train肘形机构 toggle mechanism轴 shaft轴承盖 bearing cup轴承合金 bearing alloy轴承座 bearing block轴承高度 bearing height轴承宽度 bearing width轴承内径 bearing bore diameter轴承寿命 bearing life 轴承套圈 bearing ring轴承外径 bearing outside diameter轴颈 journal轴瓦、轴承衬 bearing bush轴端挡圈 shaft end ring轴环 shaft collar轴肩 shaft shoulder轴角 shaft angle轴向 axial direction轴向齿廓 axial tooth profile轴向当量动载荷 dynamic equivalent axial load轴向当量静载荷 static equivalent axial load轴向基本额定动载荷 basic dynamic axial load rating轴向基本额定静载荷 basic static axial load rating轴向接触轴承 axial contact bearing轴向平面 axial plane轴向游隙 axial internal clearance轴向载荷 axial load轴向载荷系数 axial load factor轴向分力 axial thrust load主动件 driving link主动齿轮 driving gear主动带轮 driving pulley转动导杆机构 whitworth mechanism转动副 revolute (turning) pair转速 swiveling speed ; rotating speed转动关节 revolute joint转轴 revolving shaft转子 rotor转子平衡 balance of rotor装配条件 assembly condition锥齿轮 bevel gear锥顶 common apex of cone锥距 cone distance锥轮 bevel pulley; bevel wheel锥齿轮的当量直齿轮 equivalent spur gear of the bevel gear 锥面包络圆柱蜗杆 milled helicoids worm准双曲面齿轮 hypoid gear子程序 subroutine子机构 sub-mechanism自动化 automation自锁 self-locking自锁条件 condition of self-locking自由度 degree of freedom, mobility总重合度 total contact ratio总反力 resultant force如有你有帮助,请购买下载,谢谢!总效率 combined efficiency; overall efficiency组成原理 theory of constitution组合齿形 composite tooth form组合安装 stack mounting组合机构 combined mechanism阻抗力 resistance最大盈亏功 maximum difference work between plus and minus work纵向重合度 overlap contact ratio纵坐标 ordinate组合机构 combined mechanism最少齿数 minimum teeth number最小向径 minimum radius作用力 applied force坐标系 coordinate frame。
英译汉1.tolerance公差 puter-aided manufacturing计算机辅助制造 3.numerically controlled machines数控机床 4.necking颈缩 5.turning,drilling and boring operation 6.formability and machinability成形与可加工性 7.assembly lines装配线 8.dimensional accuracy尺寸精度 9.cross-sectional area横截面积 10.percentage elongation伸长率 11.structural strength结构强度 12.stress-strain curver应力应变曲淬火和内应力 14.earthmoving and construction equipment线 13.quenching and internal stresses土建设备 15.straightening operation 16.cracking and distortoon断裂和扭曲变形 17.light service at fractional horsepower小马力轻载 18.screw pump螺杆泵 19.steel sheet and rolled-steel shapes钢板和滚压成型钢 20.straightening operation矫正操作 21.sensing devices 传感器 21.digital or pulse motor数字与脉冲马达 22.drilling钻 boring齿轮加工镗 reaming铰 gear-cutting operations齿轮加工汉译英1.切削刀具cutting tools 2.紧固件,如螺母fasteners such as nuts 3.刚和铸铁steels and cast irons 4.马氏体和奥氏体martensite and autenite 5.机械特性mechanical properties puter-aided manufacturing计算机辅助制造 7.数控系统numerically controlled systems 8.大批量生产技术mass production techology 9.控制单元control units 10.靠模附件profiling attachment 11.弹性模量和伸长率elastic modulus and percentage elongation 12.规模经济economy of scale 13.闭环系统close-loop system 14.有色金属non-ferrous 15.液压系统hydraulic system 16.弹性和屈服极限elastic and yield limit 17.龙门刨工作台低碳钢和合金钢low-carbon steel and alloy steel 18.pianner-table 短句:1、low carbon steels do not become hard when subjected to such a heat treatment, because of the sma ll amount of carbon contained.当经历热处理、低碳钢不会变硬、因为含有少量碳。
常用机械英语大全pneumatic [nju:'mætik]∙adj. 气动的;有气胎的;充气的∙n. 气胎worktable 工作桌fit together 组装在一起[fɪt]vt. 安装;使……适应;使……合身;与……相符vi. 符合,配合;适合;合身adj. 健康的;合适的;恰当的;准备好的n. 合身;发作;痉挛fasten 锁紧(螺丝) ['fɑːs(ə)n]fixture 夹具(治具) ['fɪkstʃə; -tjə]pallet 栈板['pælɪt]barcode条码['bɑrkod]barcode scanner 条码扫描器['skænə]fuse together 熔合fuse [fju:z]∙vi. 融合;熔化,熔融∙vt. 使融合;使熔化,使熔融∙n. 保险丝;导火线,雷管thumb screw 大头螺丝thumb[θʌm]∙vt. 以拇指拨弄;作搭车手势;笨拙地摆弄;翻阅∙vi. 用拇指翻书页;竖起拇指要求搭车∙n. 拇指lbs. inch 镑、英寸front plate 前板[pleɪt]rear plate 后板 [rɪə]chassis 基座chassis ['ʃæsi] n. 底盘,底架bezel panel 面板bezel ['bezəl]∙n. 刀具的刃角;宝石的斜面;遮光板;斜视规∙vt. 把…切成或磨成斜面power button 电源按键['bʌt(ə)n]reset button 重置键voltage ['vəultidʒ]n. [电]电压sheet metal parts 冲件plastic parts 塑胶件work cell 工作间trolley 台车['trɔli]carton 纸箱sub-line 支线left fork 叉车punching machine 冲床robot 机械手diameter [daɪ'æmɪtə] 直径lathe车床[leið]planer |plein|刨床miller 铣床grinder 磨床['ɡraində]linear cutting 线切割['liniə]electrical sparkle 电火花sparkle ['spɑ:kl]n. 活力;火花;闪耀∙vt. 使闪耀;使发光∙vi. 闪耀;发泡;活跃welder ['weldə]电焊机staker=reviting machine铆合机to move, to carry, to handle搬运be put in storage['stɔːrɪdʒ]入库pack[pæk] packing包装to apply[ə'plaɪ] oil[ɒɪl]擦油to file burr 锉毛刺burr [bə:] n. 粗喉音,呼呼声∙vi. 用喉音说话∙vt. 以粗喉音发出final inspection 终检to connect material 接料to reverse material 翻料wet station 沾湿台Tiana 天那水cleaning cloth 抹布to load material 上料to unload material 卸料to return material/stock to 退料scraped 报废[skreipt]scrape ..v.刮;削deficient purchase 来料不良purchase ['pə:tʃəs]∙n. 购买;紧握;起重装置∙vt. 购买;赢得∙vi. 购买东西manufacture procedure 制程deficient manufacturing procedure 制程不良oxidation | [,ɔksi'deiʃən] |氧化scratch刮伤[skrætʃ]dents压痕defective up siding down抽芽不良defective to staking 铆合不良embedded lump 镶块feeding is not in place 送料不到位stamping-missing 漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer 备件forklift叉车['fɔ:k,lift]trailer=long vehicle拖板车['vi:ikl,compound die合模die locker锁模器pressure plate=plate pinch 压板[pintʃ]bolt 螺栓administration/general affairs dept 总务部automatic screwdriver 电动启子['skru:,draivə]thickness gauge厚薄规gauge(or jig)治具[ɡeidʒ]power wire 电源线buzzle 蜂鸣器defective product label 不良标签identifying sheet list 标示单location 地点present members 出席人员subject主题conclusion结论decision items决议事项responsible department 负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by 核准/审核/承办PCE assembly production schedule sheetPCE组装厂生产排配表model 机锺work order 工令revision 版次remark 备注production control confirmation 生产确认checked by初审approved by核准department 部门stock age analysis sheet 库存货龄分析表on-hand inventory现有库存inventory ['invəntəri, -tɔ:ri]∙n. 存货,存货清单;详细目录;财产清册available material良品可使用obsolete material良品已呆滞obsolete ['ɔbsəli:t, ,ɔbsə'li:t]∙adj. 老式的;废弃的∙n. 废词;陈腐的人∙vt. 废弃;淘汰to be inspected or reworked 待验或重工total合计cause description原因说明part number/ P/N 料号type 形态item/group/class 类别quality 品质prepared by 制表notes 说明year-end physical inventory difference analysis sheet 年终盘点差异分析表physical inventory盘点数量['invəntəriphysical count quantity 帐面数量difference quantity 差异量cause analysis 原因分析raw materials 原料materials 物料finished product 成品semi-finished product 半成品packing materials 包材good product/accepted goods/ accepted parts/goodparts 良品defective product/non-good parts 不良品disposed goods处理品warehouse/hub 仓库on way location在途仓oversea location 海外仓spare parts physical inventory list 备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM 线割EDM 放电机Coil stock 卷料sheet stock 片料tolerance 工差score=groove 压线cam block 滑块pilot 导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius 半径shim(wedge)楔子torch-flame cut 火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper 清角active plate活动板baffle plate挡块baffle ['bæfl]基本翻译n. 挡板;困惑vt. 使…困惑;使…受挫折;用挡板控制vi. 做徒劳挣扎网络释义baffle:挡板|遮蔽体|调节阻板baffle plate:遮挡板|隔板,导流板|导流板baffle board:反射板|挡板|挡水板cover plate盖板male die公模female die母模groove punch 压线冲子air-cushion eject-rod 气垫顶杆spring-box eject-plate 弹簧箱顶板bushing block 衬套insert 入块club car 高尔夫球车capability 能力parameter 参数[pə'ræmitə]factor 系数phosphate 皮膜化成['fɔsfeit] viscosity 涂料粘度[vi'skɔsəti] alkalidipping 脱脂main manifold 主集流脉bezel 斜视规['bezəl]blanking穿落模dejecting顶固模[di'dʒekt]demagnetization去磁;消磁['di:,mæɡnitai'zeiʃən, -ti'z-]high-speed transmission高速传递heat dissipation 热传[disi'peiʃən]rack 上料degrease 脱脂[di:'ɡri:s]rinse 水洗alkaline etch 龄咬['ælkəlain] [etʃ]desmut 剥黑膜D.I. rinse纯水次Chromate铬酸处理['krəumeit]Anodize阳性处理['ænəudaiz]seal封孔revision版次part number/P/N 料号good products 良品scraped products 报放心品[skreipt]defective products 不良品finished products成品disposed products处理品barcode条码flow chart 流程表单assembly组装stamping冲压molding成型spare parts=buffer 备品coordinate座标[kəu'ɔ:dinit, kəu'ɔ:dineit]dismantle the die折模auxiliary fuction 辅助功能auxiliary [ɔ:ɡ'ziljəri]基本翻译n. 助动词;辅助者,辅助物;附属机构adj. 辅助的;副的;附加的网络释义Auxiliary:辅助的|助动词|附属的auxiliary projection:辅助投影|辅视图|辅助视图auxiliary function:辅助函数|辅助功能|辅助功能[函数,操作程序poly-line 多义线heater band 加热片thermocouple 热电偶['θə:məu,kʌpl]sand blasting喷沙grit 砂砾[ɡrit]derusting machine除锈机[di:'rʌstiŋ]degate打浇口[di:'geit]dryer 烘干机induction 感应induction light感应光response=reaction=interaction感应ram连杆edge finder 巡边器concave凸concave [kɔn'keiv, 'kɔnkeiv]基本翻译n. 凹面adj. 凹的,凹面的vt. 使成凹形网络释义concave:凹的|脚窝板面凹下部分,板凹可增加板面强度和滑手动作的杠杆作用。
机械专业英语1. Introduction机械工程是一门涉及机械设备和工具设计、制造、使用和维护的学科,是工程技术领域中的一个重要分支。
机械专业英语是机械工程学习中必不可少的一部分,它涉及到机械工程师需要掌握的英语词汇、专业术语、文档阅读和撰写技巧等方面。
本文将介绍一些常用的机械专业英语词汇和常用的表达方式,以帮助读者更好地掌握机械专业英语。
2. Mechanical Engineering Vocabulary以下是一些常用的机械工程专业词汇,可以帮助读者对机械工程领域的基本概念有更好的了解:•Mechanical Engineering(机械工程): A discipline of engineering that deals with the design, construction, and operation of machinery.•Engineer(工程师): A person who designs, builds, or maintains engines, machines, or public works.•CAD(计算机辅助设计): Computer-Aided Design, a software tool used by engineers to create and modifymechanical designs.•CAM(计算机辅助制造): Computer-Aided Manufacturing, a software tool used to controlmanufacturing processes.•CNC(计算机数控): Computer Numerical Control,a method of controlling manufacturing machines usingcomputers.3. Common Expressions in Mechanical Engineering在机械工程领域,有一些常用的表达方式,以下是一些示例:•According to the design specifications(根据设计规范): Indicates that something is done in accordance with the design requirements.•The machine is in operation(机器正在运行): Indicates that the machine is currently running andperforming its intended function.•The material is heat-treated(材料经过热处理): Indicates that the material has undergone a specific heat treatment process for improved properties.•The system is experiencing mechanical failure(系统发生机械故障): Indicates that the system is notfunctioning properly due to a mechanical issue.•The component needs to be lubricated regularly(零部件需要定期加润滑油): Indicates that regularlubrication is required to ensure proper functioning of the component.4. Reading and Writing Documents in Mechanical Engineering在机械工程领域,阅读和撰写文档是非常重要的技能。
机械工程专业英语翻译Introduction机械工程是一门涵盖机械原理、设计、制造以及维护的综合性学科,其中涉及许多专业术语和英语翻译。
良好的英语翻译能力对机械工程师在国际合作和成果交流中至关重要。
本文将介绍机械工程专业中常见的英语单词和短语,并提供中文翻译和相关注释。
Mechanical Principles 机械原理对于机械原理,下面是一些常见的英语单词和短语。
1.Mechanism(机构):A mechanism is a device designedto transform input forces and movement into a desiredoutput force and movement.2.Kinematics(运动学):Kinematics is the study ofmotion, without regard to the cause of the motion.3.Statics(静力学):Statics is the study of thebehavior of structures, under the action of forceswithout producing motion.4.Dynamics(动力学):Dynamics is the study of thebehavior of motion of objects under the action of forces.5.Thermodynamics(热力学):Thermodynamics deals withthe relationships between heat, work, and energy.6.Fluid Mechanics(流体力学):Fluid mechanics is thestudy of the behavior of fluids at rest or in motion. Mechanical Design 机械设计对于机械设计,下面是一些常见的英语单词和短语。
机械制图Descriptive Geometry & Engineering Graphing 85机械工程材料Mechanical Engineering Material 90工程力学Engineering Mechanics 89机械原理Principle of Mechanics 85机械原理课程设计Course Exercise for Principle of Mechanics good良好机械设计Mechanical Design 80机械设计课程设计Course Exercise for Mechanical Design good良好液压与气压传动Hydraulic & Pneumatic Technology 89机械制造技术基础Fundamentals of Manufacturing Technology 77机械制造装备设计Modern Manufacturing Equipment Design 84电工与电子技术Mechanical Electric Electronic Control Technique 86微型计算机原理Principle and Application of Microcomputer 81互换性与测量技术Fundamentals of Exchangeability and Measurement Technology 77机械工程控制基础Introduction to Control Engineering 85计算机数控技术Technology and Application of Numerical Control Programming77PLC Principle and Application of PLC 82模具制造技术Mould Manufacture Technology 76传感器与测试技术Measurement and Testing Technology 81计算机辅助设计Computer-aided Design 86机械系统设计Mechanical System Design 88生产实习Production Practical Training good良好机械制图、机械工程材料、工程力学、机械原理、机械原理课程设计、机械设计、机械设计课程设计、液压与气压传动、机械制造技术基础、机械制造装备设计、电工与电子技术、微型计算机原理、互换性与测量技术、机械工程控制基础、计算机数控技术、PLC、模具制造技术、传感器与测试技术、计算机辅助设计、机械系统设计、生产实习等由于在大二第一学期就过了英语6级,所以,从那个时候起,一直都在通过选修口语课,加入英语角,看美剧,晨读等方式学英语口语,因此口语水平良好,可以和以英语为母语的人进行交流。
一、汉译英
载荷:load
内应力internal stress
灵敏度sensitivity
疲劳强度fatigue strength
铣床milling machine
供水系统water supply system
进料速度feedrate
闭合序列closed sequence
专家系统expert system
CAE computer –aided engineering 二、英译汉
impurity杂志
machinability加工性能
sound judgement正确的判断力dynamic load动载荷
lathe车床
vertical support垂直支撑
speed indicator速度表
machine vision机器视觉manipulator操纵器
三、句子汉译英
1、金属和合金的差异一般很难界定。
The distinction between a metal and a nonmetal is not always clear out. 2、钢的冷成型性是由它的拉伸强度与延展性共同决定的。
The cold-formability of steel is a function of its tensile strength combined with ductility.
3、当承载时,材料将发生变形,变形量取决于载荷的大小。
A material tends to change or changes its dimensions when it is loaded ,depending upon the magnitude of the load.
4、机电一体化是一个用于描述机械和电子工程集成的术语。
“Mechatronics”is a term to describe the integration of mechanical and electronical engineering.
5、机器人执行的工作可分为两类:危险性工作和重复性工作。
Jobs performed by robots can be devided into two major categories :hazardous jobs and repetitive jobs.
6、CIM系统不仅包含生产控制系统,还有生产计划和管理系统。
CIM technology will be used implement plant-wide integration ,and intelligent maintenance system.
四、句子英译汉
1、The most important by far is iron, on which are based the
ubiquitous steels and cast irons.
2、The properties of the final part (hardness, strength, and
machinability), rather than properties required by forging, govern the selection of material.
3、Logically speaking, once the elastic limit is exceeded, the metal
should start to yield, and finally break, without any increase in the value of stress.
4、 A machine control system is a combination of electronic circuitry
sensing devices, and mechanical components.
5、Grinding operation are used to impart a high-quality surface finish
on the workpiece.
6、The tensile strength of a material is obtained by dividing the
maximum load, which the specimen bears by the area of cross-section of the specimen.
7、The purpose of the design calculation is to attempt to predict the
stress or deformation in the part.
8、Automatic control systems are sometimes called
servomechanisms. which may be a complex array of electromechanical components or a simple mechanical device.
9、Fluid mechanics is the branch of engineering science that is
concerned with forces and energies generated by fluids at rest and in motion.
10、Except for machine vision and software,Japanese basic research
was comparable to the United States.
五、段落翻译
Machinability is not determined by hardness alone,but by the youghness,microstructure,chemical composition,and tendency of a me没写完
忠才() 00:02:16
Machinability is not determined by hardness alone,but by the toughness,microstructure,chemical composition,and tendency of a metal to harden under cold work.In the misleading expression “too hard to machine”, the work “hard”is usually meant to be synonymous with “difficult”. Many times a material is actually too soft to machine rea dily. Softness and toughness may cause the metal to tear and flow ahead of the cutting tool rather than cut cleanly. Metal that are inherently soft and tough are sometimes alloyed to improve their machinability at some sacrifice in ductility. Examples are use of lead in brass and of sulfur in steel.
加工性不仅仅只由硬度决定,它还由韧性,微观结构,化学成分和在冷加工下金属所呈现的硬化特性所决定。
在容易混淆的表示“难加工”中,难与困难同义。
许多时候,因为材料过软而难于稳定加工。
材料
柔软性和韧性能够产生金属撕裂,使金属在完成切削前流动至刀具前端。
柔软的金属往往会被加入合金从而牺牲它的延展性来提高加工性能。
如黄铜中加入铅钢中加入硫
概念在控制系统中发挥着重要的作用。
反馈是闭环系统的一个重要的必要条件。
没有反馈,一个控制系统在大多数的实际应用中将不能保证准确性和可靠性。
实际上,应用反馈系统的原因是它带来的意义远不止简单的为了减少错误而比较输入与输出。
系统错误的减少仅仅是反馈可能带给一个系统的许多影响中的一个。
我们现在应该知道反馈也对系统的基本性能有影响,如稳定性,带宽,总增益,阻抗和灵敏度。