sh39f003规格书

This is information on a product in full production. August 2018DS7147 Rev 10Value line, 16-MHz STM8S 8-bit MCU, 8-Kbyte Flash memory, 128-byte data EEPROM, 10-bit ADC, 3 timers, UART, SPI, I²CDatasheet - production dataFeaturesCore•16 MHz advanced STM8 core with Harvardarchitecture and 3-stage pipeline•Extended instruction setMemories•Program memory: 8 Kbyte Flash memory; dataretention 20 years at 55 °C after 100 cycles•RAM: 1 Kbyte•Data memory: 128 bytes true data EEPROM;endurance up to 100 k write/erase cyclesClock, reset and supply management•2.95 V to 5.5 V operating voltage•Flexible clock control, 4 master clock sources–Low-power crystal resonator oscillator–External clock input–Internal, user-trimmable 16 MHz RC–Internal low-power 128 kHz RC•Clock security system with clock monitor•Power management–Low-power modes (wait, active-halt, halt)–Switch-off peripheral clocks individually–Permanently active, low-consumptionpower-on and power-down resetInterrupt management•Nested interrupt controller with 32 interrupts•Up to 27 external interrupts on 6 vectorsTimers•Advanced control timer: 16-bit, 4 CAPCOMchannels, 3 complementary outputs, dead-time insertion and flexible synchronization•16-bit general purpose timer, with 3 CAPCOMchannels (IC, OC or PWM)•8-bit basic timer with 8-bit prescaler•Auto wakeup timer•Window and independent watchdog timersCommunications interfaces •UART with clock output for synchronousoperation, SmartCard, IrDA, LIN master mode•SPI interface up to 8 Mbit/s•I2C interface up to 400 Kbit/sAnalog to digital converter (ADC)•10-bit ADC, ± 1 LSB ADC with up to 5multiplexed channels, scan mode and analogwatchdogI/Os•Up to 28 I/Os on a 32-pin package including 21high-sink outputs•Highly robust I/O design, immune againstcurrent injectionDevelopment support•Embedded single-wire interface module(SWIM) for fast on-chip programming and non-intrusive debugging

MF51E

High Precision

NTC Thermistor for

Extremely Accurate

Temperature

Measurement

/Main Techno-Parameter High Precision NTC Thermistors for

Extremely Accurate Temperature Measurement.

The MF51E NTC Thermistors were specially designed for use in electronic thermometers which require better than average accuracy. The extremely small size allows the thermistor to respond very quickly to tiny changes in temperature. The MF51E can be supplied un-calibrated with standard tolerances or calibrated and grouped according to R at 37°C±0.01% for extreme interchangeability so as to eliminate the need for other calibrations.MF51E

Dimensions

/

KΩKΩKΩApplication• Electronic Thermometers• Medical Equipment and Patient MonitoringCharacteristics• Small Size and fast response and light weight• Available tolerances: ±0.5%, ±1%, ±2%, ±3% and ±5%• B Value tolerances: ±0.5%, ±1.0% and ±2.0%• Resistance calibration available at 37°C ±0.01% (see table for details of grouping)• Long-term Stability and Reliability• Excellent Tolerance and Interchangeability• Available in all popular resistance values• Dissipation Constant ≥0.7mW/°C• Time Constant of ≤3.2 seconds • Rated Power: 3.5mW• Operating Temperature Range -40°C to 100°CSpecification

SaRonixNTH / NCH SeriesSaRonixCrystal Clock OscillatorTechnical Data3.3V, LVCMOS / HCMOS, Tri-State

141 Jefferson Drive • Menlo Park, CA 94025 • USA • 650-470-7700 • 800-227-8974 • Fax 650-462-9894DS-159 REV DSymmetry:Rise and Fall Times:Logic 0:Logic 1:Load:Period Jitter RMS:0.5 MHz to 106.25 MHzFrequency Stability:Frequency Range:±20, ±25, ±50 or ±100 ppm over all conditions: calibrationtolerance, operating temperature, input voltage change,load change, 30 day aging, shock and vibration.Temperature Range:Operating:Storage:0 to +70°C or -40 to +85°C, See Part Numbering Guide-55 to +125°CSupply Voltage:Recommended Operating:3.3V ±10%Supply Current:20mA max, 0.5 to 30 MHz25mA max, 30+ to 50 MHz30mA max, 50+ to 80 MHz35mA max, 80+ to 106.25 MHzACTUAL SIZEDescriptionA crystal controlled, low current, lowjitter and high frequency oscillator withprecise rise and fall times demanded innetworking applications. The tri-statefunction on the NTH enables the outputto go high impedance. Device is pack-aged in a 14 or an 8-pin DIP compatibleresistance welded, all metal groundedcase to reduce EMI. True SMD DIL14versions for IR reflow are available, se-lect option "S" in part number builder.See separate data sheet for SMD packagedimensions.Output Drive:45/55% max 0.5 to 70 MHz max40/60% max @ 50% VDD4ns max 0.5 to 50 MHz, 20% to 80% VDD3ns max 50+ to 80 MHz1.5ns max 80+ to 106.25 MHz10% VDD max90% VDD min50 pF, 0.5 to 50 MHz30pF, 50+ to 70 MHz15pF, 70+ to 106.25 MHz8ps maxHCMOS

/

/

/

/

/

/

/

Descriptions:

1. Delta will not guarantee the performance of the products if the application condition falls

outside the parameters set forth in the specification.

2. A written request should be submitted to Delta prior to approval if deviation from this

specification is required.

3. Please exercise caution when handling fans. Damage may be caused when pressure is applied

to the impeller, if the fans are handled by the lead wires, or if the fans are hard-dropped to the

production floor.

4. Except as pertains to some special designs, there is no guarantee that the products will be free

from any such safety problems or failures as caused by the introduction of powder, droplets of

water or encroachment of insect into the hub.