CAR PARKING SENSOR说明书004款

Controls Light SwitchesRotating the light switch turns the lights onand off, regardless of the power modesetting.■High beamsPush the lever forward until you hear a click.■Low beamsWhen in high beams, pull the lever back toreturn to low beams.■Flashing the high beamsPull the lever back, and release it.■Lights offTurn the lever to OFF either when:•The transmission is in P.•The parking brake is applied.To turn the lights on again, turn the lever toOFF to cancel the lights off mode. Even if youdo not cancel the lights off mode, the lightscome on automatically when:•The transmission is taken out of P and theparking brake is released.•The vehicle starts to move.■Manual Operation1Light SwitchesIf you leave the power mode in VEHICLE OFF whilethe lights are on, a chime sounds when the driver’sdoor is opened.When the lights are on, the lights on indicator in theinstrument panel will be on.Do not leave the lights on when the engine is offbecause it will cause the battery to discharge.If you sense that the level of the headlights isabnormal, have the vehicle inspected by a dealer.Flashing the high beamsLow BeamsFlashing the high beamsLow BeamsCanadian modelsControlsAutomatic lighting control can be used when the power mode is in ON.When the light switch is in AUTO , theheadlights and other exterior lights will switch on and off automatically depending on the ambient brightness.The headlights comes on when you unlock a door in dark areas with the headlight switch in AUTO .u Once you lock the door, the headlights will go off.■Automatic Operation (automatic lighting control)1Automatic Operation (automatic lighting control)We recommend that you turn on the lights manually when driving at night, in a dense fog, or in dark areas such as long tunnels or parking facilities.The light sensor is in the location shown below.Do not cover this light sensor with anything;otherwise, the automatic lighting system may notwork properly.Light SensorModels without automaticintermittent wipersLight SensorModels with automatic intermittent wipers*Controls The headlights automatically come on when the wipers are used several times withina certain number of intervals with the headlight switch in AUTO.The headlights automatically go off a few minutes later if the wipers are stopped.The headlights, all other exterior lights, and the instrument panel lights turn off 15seconds after you set the power mode to VEHICLE OFF, take the remote with you,and close the driver’s door.If you set the power mode to VEHICLE OFF with the headlight switch on, but do notopen the door, the lights turn off after 10 minutes (three minutes, if the switch is inthe AUTO position).The lights turn on again when you unlock or open the driver’s door. If you unlockthe door, but do not open it within 15 seconds, the lights go off. If you open thedriver’s door, you will hear a reminder chime alerting you that the lights are on.Fog Lights*When the low beam headlights are on, turnthe fog light switch on to use the fog lights.■Headlight Integration with Wipers■Automatic Lighting Off Feature1Automatic Operation (automatic lighting control)You can adjust the auto light sensitivity as follows:SettingThe exterior lights come onwhen the ambient light is atMaxHighMidLowMinU.S. modelsBrightDark1Headlight Integration with WipersThis feature activates while the headlights are off inAUTO.The instrument panel brightness does not changewhen the headlights come on.At dark ambient light levels, the automatic lightingcontrol feature turns on the headlights, regardless ofthe number of wiper sweeps.1Automatic Lighting Off FeatureYou can change the headlight auto off timer setting.Fog Light SwitchControlsAuto High-BeamThe front sensor camera detects the light sources ahead of the vehicle such as the lights of a preceding or oncoming vehicle, or street lights. When you are driving at night, the system automatically switches the headlights between low beam and high beam depending on the situation.When all of the following conditions have been met, the auto high-beam indicator comes on and the auto high-beam is activated.•The power mode is in ON.•The light switch is in AUTO .•The lever is in the low beam position.•The headlights have been automatically activated.•It is dark outside the vehicle.If the auto high-beam indicator does not come on even when all the conditions have been met, carry out the following procedure and the indicator will come on.•Pull the lever toward you for flashing the high beams then release it while driving.1Auto High-BeamThe auto high-beam system does not always operate in every situation. This system is just for assisting the driver. Always observe your surroundings and switch the headlights between high beam and low beam manually if necessary.If you find the timing of beam changes inconvenient for driving, change the headlight beams manually.The range and the distance at which the camera can recognize varies depending on conditions surrounding your vehicle.Regarding the handling of the camera mounted to the inside of the windshield, refer to the following.2Front Sensor Camera For the auto high-beam to work properly:•Do not place an object that reflects light on the dashboard.•Keep the windshield around the camera clean.•When cleaning the windshield, be careful not to apply the windshield cleanser to the camera lens.•Do not attach an object, sticker or film to the area around the camera.•Do not touch the camera lens.If the camera receives a strong impact, or repairing of the area near the camera is required, consult a dealer.■How to Use the Auto High-BeamFront Sensor CameraAuto High-Beam IndicatorLight SwitchControls ■Automatic switching between high-beam and low-beamWhen auto high-beam is active, the headlights switch between high beam and lowbeam based on the following conditions.■Manual switching between high-beam and low-beamIf you want to manually switch the headlights between high beam and low beam,follow either of the procedures below. Note that when you do this, the auto high-beam indicator will turn off and the auto high-beam will be deactivated.Using the lever:Pull the lever toward you for flashing the high beams then release it within aboutone second while driving.u To reactivate the auto high-beam, pull the lever toward you for flashing thehigh beams then release it while driving. The auto high-beam indicator willcome on.Using the light switch:Turn the light switch to .u To reactivate the auto high-beam, turn the light switch to AUTO when theSwitching to high beam:Switching to low beam:All of the following conditions mustbe met before the high beams turnon.●Your vehicle speed is 25 mph (40km/h) or more.●There are no preceding oroncoming vehicle with headlightsor taillights turned on.●There are few street lights on theroad ahead.One of the following conditionsmust be met before the low beamsturn on.●Your vehicle speed is 15 mph (24km/h) or less.●There is a preceding or oncomingvehicle with headlights ortaillights turned on.●There are many street lights onthe road ahead.1How to Use the Auto High-BeamIn the following cases, the auto high-beam systemmay not switch the headlights properly or theswitching timing may be changed. In case of theautomatic switching operation does not fit for yourdriving habits, please switch the headlights manually.•The brightness of the lights from the preceding oroncoming vehicle is intense or poor.•Visibility is poor due to the weather (rain, snow,fog, windshield frost, etc.).•Surrounding light sources, such as street lights,electric billboards and traffic lights are illuminatingthe road ahead.•The brightness level of the road ahead constantlychanges.•The road is bumpy or has many curves.•A vehicle suddenly appears in front of you, or avehicle in front of you is not in the preceding oroncoming direction.•Your vehicle is tilted with a heavy load in the rear.•A traffic sign, mirror, or other reflective objectahead is reflecting strong light toward the vehicle.•The oncoming vehicle frequently disappears underroadside trees or behind median barriers.•The preceding or oncoming vehicle is a motorcycle,bicycle, mobility scooter, or other small vehicle.The auto high-beam system keeps the headlight lowbeam when:•Windshield wipers are operating at a high speed.•The camera has detected a dense fog.ControlsYou can turn the auto high-beam system off. If you want to turn the system off or on, set the power mode to ON, then carry out the following procedures while the vehicle is stationary.To turn the system off:With the light switch is in AUTO , pull the levertoward you and hold it for at least 40 seconds. After the auto high-beam indicator light blinks twice, release the lever.To turn the system on:With the light switch is in AUTO , pull the lever toward you and hold it for at least 30 seconds. After the auto high-beam indicator light blinks once, release the lever.■How to Turn Off the Auto High-Beam1How to Use the Auto High-BeamIf the Some Driver Assist Systems CannotOperate: Camera Temperature Too High message appears:•Use the climate control system to cool down the interior and, if necessary, also use defroster mode with the airflow directed toward the camera.•Start driving the vehicle to lower the windshield temperature, which cools down the area around the camera.If the Some Driver Assist Systems Cannot Operate: Clean Front Windshield message appears:•Park your vehicle in a safe place, and clean the windshield. If the message does not disappear after you have cleaned the windshield and driven for a while, have your vehicle checked by a dealer.1How to Turn Off the Auto High-BeamIf you turn the auto high-beam system off, the system does not operate until you turn the system on.Park in a safe place before turning the system off oron.。

Rotating Display Euro NCAP Five-Star Rating Ultra-Safe Patented Blade Battery TechnologyBYD ATTO 3 SPECIFICATIONSSpeci cationsOverall length (mm)Overall width (mm)Overall height (mm)Wheel track - front / rear (mm)Wheelbase (mm)Ground clearance unladen (mm)Luggage capacity - Min (L)Luggage capacity - Max (L)Kerb weight (kg)Gross vehicle mass (kg)PowertrainMotor typeMaximum power (kW/Hp)Maximum torque (N.m)PerformanceAcceleration 0-100km/h (s)Driving range: NEDC (km)Seating capacityBatteryBattery typeBattery capacity (kWh)SuspensionFront suspensionRear suspensionBrakeFrontRearTyreWheel typeTyre sizeNew EnergyDomestic 3-pin plug AC chargerAC charging port - Type 2DC charging port - CCS 2 (70kW)DC charging port - CCS 2 (80kW)VTOL mobile power supply function4,4551,8751,6151,575/1,5802,7201754401,3401,680 1,7502,090 2,160Permanent magnetsynchronous motor150/2033107.3410 4805BYD Blade Battery49.92 60.48Macpherson strutMulti-linkVentilated discDiscAlloy215/60 R17 215/55 R18VTOL mobile power supply unitRegenerative brakingExteriorPanoramic sunroof with electric slide and anti-trapElectric unlock tailgateOne-touch open / close tailgateRoof railsElectrically heated and adjustable exterior mirrorsElectrically retractable exterior mirrorsInteriorSteering wheel mounted controls - audio, phone,ACC and multi-function displayElectric power assisted steering system5" digital instrument panelSynthetic leather seat60/40 split fold rear seats6-way power adjustment - driver seat4-way power adjustment - front passenger seatISOFIX child restraint anchorage points(outer rear seats)SafetyFront airbags - driver & front passengerSide airbags - driver & front passengerSide curtain airbags - front & rearFar-side airbag - driverSeat belt reminder - front & rear360° view monitorTyre Pressure Monitoring System (TPMS)Front 2 radars (Parking Sensor)Rear 4 radars (Parking Sensor)Auto holdElectric Parking Brake System (EPB)Anti-Lock Braking System (ABS)Electronic Stability Program (ESP)Traction Control System (TCS)Electronic Brake Force Distribution (EBD)Hill Decent Control (HDC)Stop & Go Full Speed Adaptive Cruise Control(ACC-S&G)Automatic Emergency Braking System (AEB)Front Collision Warning (FCW)Rear Collision Warning (RCW)Blind Spot Detection (BSD)Door Open Warning (DOW)Rear Cross Tra c Alert (RCTA)LightLED headlightFollow me home headlightAdaptive Front Light (AFL)LED rear lightSingle-color gradient ambient lighting - door handleMulti-color gradient ambient lighting with musicrhythm - door handleEntertainmentFM radio*Bluetooth® phone connectivity and audiostreaming12.8" intelligent rotating touch screen6 speakers*Dirac HD sound®, 8 speakers*Apple CarPlay® (USB) and Android Auto™(wireless) (available in Q2 2023)Voice assistant - English*Satellite navigation*Music streamingUSB - C port ×1 + USB - A port ×1, centre consoleUSB - C port ×1 + USB - A port ×1, rearComfort & ConvenienceWireless phone charger12V socketKeyless entry & Keyless startPortable card key4-door window one touch up-down with anti-pinchCentre console storage compartmentEmergency kit with warning triangle and safety vestTyre repair kitAir ConditioningAutomatic air-conditioningHeat pumpCN95 air lterPM 2.5 air lter*Note:The real range is in uenced by many factors such as individual driving style, load, tra c etc. The declared range isestimated for reference only.Bluetooth® is a registered trademark of Bluetooth SIG, Inc. Compatibility and functionality varies dependingon device.Apple CarPlay® is a registered trade mark of Apple Inc. Requires compatible device, USB connectionAndroid Auto™ is a registered trade mark of Google Inc. Requires compatible device, and wireless Android Auto™ iscompatible with an active data plan, 5 GHz Wi-Fi support, and the latest version.Dirac HD sound® is a registered trade mark of Dirac Research AB .BYD provides free map update for 3 years.Music streaming requires data usage or over Wi-Fi.Colours depicted are a guide only and may vary from actual colours due to the printing.Driving assist system are not a substitute for the driver’s responsibility of the vehicle.Emergency kit includes safety vest, warning triangle, front tow connection and clip for tyre.BYD reserves the right to vary vehicle speci cations and standard features from those detailed in this brochure.ENCAP test car is left hand version.2,720mm4,455mm1,615mm1,580mm1,875mm1,575mm1,875mmDIMENSIONSBODY COLORCONFIGURATIONS●●●●●●●●●—●●●●—●●●●●●—●●●●●●●●●●—●●●●●●●●—●●●●—●●●●●●●●●●●●●●●●●●●●●●●—●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●●—●●●—●●Advanced SuperiorINTERIOR COLOREclipse Blue + Hazy GreySTANDARDRANGEEXTENDEDRANGESTANDARDRANGEEXTENDEDRANGEbyd.simedarbymotors.my1300-38-1888BYD Cars MalaysiaSime Darby Motors City, No. 6, Jalan P JU 1A/7Ara Damansara, 47301 Petaling Jaya, Selangor, Malaysia.SIME DARBY BEYOND AUTO SDN. BHD.Forest Green Parkour Red Boulder Grey Ski WhiteSurf Blue。

CONTENTSWHAT’S IN THE BOX (2)SAFETY PRECAUTIONS (2)INSTALLATION SAFETY WARNING (2)INSTALLATION SAFETY INSTRUCTIONS (3)PRODUCT INFORMATION (4)PRODUCT OVERVIEW (4)PRODUCT FEATURES (5)PRODUCT TECHNICAL SPECIFICATIONS (6)GETTING STARTED (7)EQUIPMENT INSTALLATION - PREPARATIONFOR INITIAL USAGE (7)MEMORY CARD OPTION (8)MEMORY CARD FORMATTING (8)SOFTWARE SETTING (9)LANGUAGE SETTING (9)TIME SETTING (9)MAIN FUNCTIONS AND BASIC OPERATIONSOF THE DEVICE (10)DEVICE POWER ON/OFF MODE (10)PARKING MONITORING MODE (10)VIDEO RECORDING MODE (11)PHOTOGRAPH MODE (12)PLAYBACK MODE (12)FILE MANAGEMENT (13)SPECIFICATIONS FOR SHORCUT KEY FUNCTIONS (14)DISCLAIMER (14)219354687101513141112PRODUCT TECHNICAL SPECIFICATIONSNote:HELLA reserves the rights of modification for design and specifications without further notice. If there is any difference, please subject to the actual device.EQUIPMENT INSTALLATIO N - PREPARATIO N FO R INITIAL USAGE1.Please fix the vehicle powerline according to the diagrambelow to avoid blockingvisibility during driving.It is better that the drivingvideo recorder be fixed at thefront of the interior mirror tohave a better recording angle.2. Please do not install the driving video recorder at any place that may distract the attention of the driver.SOFTWARE SETTINGMAIN FUNCTIONS AND BASIC OPERATIONSOF THE DEVICEDEVICE POWER ON/OFF MODEPARKING MONITORING MODEThis device has two parking monitoring mode which are P mode and T mode. The specific application and instructions are as follows:function will be activated upon vibration,and an icon ofthe screen. Start this function, and ifthe vehicle experience collision afterpower-off, the driving video recordertime-lapse video recording function.An icon ofscreen after this function is started. Thevideo recording will continually snap atthe speed of 1 shot per second, and laterVIDEO RECORDING MODEAfter starting up, video recording will commence. Video recording can be operated by pressing the OK button.PHOTOGRAPH MODEUnder the video recording mode, hold the menu button for 3 seconds to enter the Photograph Mode. Enter OK button to take one photo. Press menu button to enter main menu selection for option setting including image size, AWB (picture contrast), image quality, exposure adjustment and photo sensitivity, etc.PLAYBACK MODEUnder the stop status of video recording, press the Playback Mode button twice to switch to Playback Mode. Under thePlayback Mode, press the menu button for a list of operationincluding volume adjustment, delete, delete all files, protect and cancel a single file. If the current file is a video file, press OK button for play or pause on this device, press the Up/ Down button for the fast forward/ fast backward operations, press the menu button to stop and quit the current video playing.FILE MANAGEMENTSPECIFICATIONS FOR SHORCUT KEY FUNCTIONSNote: The on-state is “” under the menu setting and the off-state is “”.- This device is NOT intended to be used for illegal purposes; surveillance and shall not be used in any form as evidence for claim purposes.- Some countries prohibit drivers from mounting anything on the windshield, or restrict mounting to specific areas of the windshield. It is the owner’s responsibility to mount the device in compliance with local laws.- Errors may occur depending on the surrounding environment and the voltage of the car.- Company is not liable/responsible for non-recorded event, missing files, etc.目录包装盒中有哪些内容 (16)安全须知 (16)安装安全警告 (16)安装安全说明 (17)产品信息 (18)产品概述 (18)产品特性 (19)产品技术规格 (20)入门指南 (21)设备安装 - 初次使用准备 (21)储存卡选配 (21)储存卡格式化 (21)软件设定 (22)语言设定 (22)时间设置 (22)设备的主要功能及基本操作 (23)设备开启/关闭模式 (23)停车监控模式 (23)录影模式 (24)拍照模式 (25)回放模式 (25)文件管理 (26)快捷键功能说明 (26)免责声明 (27)219354687101513141112产品技术规格注意:HELLA保留设计和规格更改权，恕不另行通知。

INSTRUMENT PANELIndicators, gauges, and displays related to driving the vehicle.Indicators briefly appear with each engine start and then go out. Red and amber indicators are most critical. Blue and green indicators are used for general information.Malfunction IndicatorsThese are the most critical indicators. If they come on and stay lit while driving or at any other time, there may be a problem. See your dealer for assistance.U .S .Can adaBrake system (red)•Comes on when the parking brake is applied, and goes off when it is released.•Comes on when the brake fluid is low.•Comes on if there is a problem with the brake system.•The beeper sounds and the indicator comes on if you drive with the parking brake not fully released.•Comes on while driving - Make sure the parking brake is released. Check the brake fluid level.•Comes on along with the ABS indicator - Have your vehicle checked by a dealer.•Blinks and the parking brake and brake system indicator (amber)comes on at the same time - There is a problem with the electric parking brake system. The parking brake may not be set.Avoid using the parking brake and have your vehicle checked by a dealer immediately.Brake system (amber)•Comes on if there is a problem with the radar sensor.•Indicator may come on temporarily when the Maximum Load Limit is exceeded.•Comes on if there is a problem with a system related to braking other than the conventional brake system.•Comes on if there is a problem with the electric parking brake system or the automatic brake hold system.Low oil pressureEngine oil pressure is low.•Comes on while driving - Immediately stop in a safe place. Charging System IndicatorComes on when the battery is not charging.Supplemental Restraint System (SRS)Comes on if a problem with any of the following is detected:•Supplemental restraint system•Side airbag system•Side curtain airbag system•Seat belt tensionerStays on constantly or does not come on at all - Have your vehicle checked by a dealer.Lane Keeping Assist System (LKAS)There is a problem with the system.Stays on constantly or does not come on at all - Have your vehicle checked by a dealer.Malfunction Indication Lamp (check engine light)1.5 L engine models:•Comes on when you turn the ignition switch to ON*1, and goes off when the engine starts, or after several seconds if the engine did not start. If "readiness codes" have not been set, it blinks five times before it goes off.2.0 L engine models:•Comes on when you turn the power mode ON, and goes off when the engine starts If "readiness codes" have not been set, it blinks five times before it goes off.•Comes on if there is a problem with the emissions control system.•Blinks when a misfire in the engine's cylinders is detected.•Readiness codes are part of the on board diagnostics for the emissions control systems.•Comes on while driving - Have your vehicle checked by a dealer.•Blinks while driving - Stop in a safe place where there are no flammable objects. Stop the engine for 10 minutes or more, and wait for it to cool down. Then, take your vehicle to a dealer.Anti-lock Brake System (ABS)There is a problem with the anti-lock brake system. Your vehicle still has normal braking ability, but no anti-lock function.Low Tire Pressure / Tire Pressure Monitoring System (TPMS)*13 Comes on and stays on when:•One or more tires' pressures are determined to be significantly low.•The system has not been calibrated.•Comes on while driving - Stop in a safe place, check tire pressures, and inflate the tires(s) if necessary.•Stays on after the tires are inflated to the recommended pressures - The system needs to be calibrated.Vehicle Stability Assist® (VSA®) SystemComes on if there is a problem with the brake assist system, VSA®or hill start assist system.•Stays on constantly - Have your vehicle checked by a dealer.*1 - If equipped*13 - US models only, if equippedCollision Mitigation Braking System™ (CMBS™)•Stays on constantly without the CMBS™ off - Have your vehicle checked by a dealer.•Comes on if the CMBS™ is deactivated temporarily after the battery has been disconnected, then re-connected.•Drive a short distance at more than 12 mph (20 km/h). The indicator should go off. If it does not, have your vehicle checked by a dealer.•Comes on when the CMBS™ system shuts itself off.•Stays on - The area around the camera is blocked by dirt, mud, etc. Stop your vehicle in a safe place, and wipe it off with a soft cloth.•Stays on - The temperature inside the camera is too high. Use the climate control system to cool down the camera. The system activates when the temperature inside the camera cools down.•Indicator may come on temporarily when the Maximum Load Limit is exceeded.•Make sure the total load is within the Maximum Load Limit.•Stays on constantly - Have your vehicle checked by a dealer.Road Departure Mitigation (RDM)•Comes on if there is a problem with the RDM system.•Stays on constantly - Have your vehicle checked by a dealer.•Comes on if the RDM is deactivated temporarily after the battery has been disconnected, then re-connected. Drive a short distance at more than 12 mph (20 km/h). The indicator should go off. If it does not, have your vehicle checked by a dealer.•Comes on when the RDM system shuts itself off.•Indicator may come on temporarily when passing through an enclosed space, such as tunnel.•The area around the radar sensor is blocked by dirt, mud, etc. Stop your vehicle in a safe place, and wipe it off with a soft cloth.•Have your vehicle checked by a dealer if the indicator does not go off even after you cleaned the radar sensor.•Stays on - The temperature inside the camera is too high. Use the climate control system to cool down the camera. The system activates when the temperature inside the camera cools down.•Indicator may come on temporarily when the Maximum Load Limit is exceeded.•Make sure the total load is within the Maximum Load Limit. Blind Spot Information*1There is a problem with the system, or the sensor is blocked. Electric Power Steering (EPS) SystemComes on if there is a problem with the EPS system.*1 - If equippedAdaptive Cruise Control (ACC)*1 with Low Speed Follow*1•Comes on if there is a problem with ACC with Low Speed Follow.•Comes on while driving - Have your vehicle checked by a dealer.•Comes on if the ACC with Low Speed Follow*1 is deactivated temporarily after the battery has been disconnected, thenreconnected.•Drive a short distance at more than 12 mph (20 km/h). The indicator should go off. If it does not, have your vehicle checked by a dealer.•Indicator may come on temporarily when the Maximum Load Limit is exceeded.•ACC with Low Speed Follow has been automatically canceled.•Make sure the total load is within the Maximum Load Limit.•Stays on constantly - Have your vehicle checked by a dealer. Electric Parking Brake SystemStays on constantly or does not come on at all - Have your vehicle checked by a dealer.Transmission System Indicator*1•Blinks if the transmission system has a problem.•Blinks while driving - Avoid sudden starts and acceleration and have your vehicle checked by a dealer immediately.*1 - If equippedCondition IndicatorsThese indicators may require you to perform an action.U.S. Can ada Parking BrakeRelease the parking brake before driving. You will hear a beep if you drive with it not fully released.Seat Belt ReminderThe indicator blinks and beeps sound continuously if you or your front passenger has not fastened your seat belts when you begin driving. If the indicator remains on after seat belts are fastened, see your dealer.Low FuelRefuel as soon as possible. If the indicator blinks, there is a problem with the fuel gauge. See your dealer.•Comes on when the fuel reserve is running low (approximately 1.8 U.S. gal/7.0 Liter left).•Blinks if there is a problem with the fuel gauge.Low Tire Pressure / Tire Pressure Monitoring System (TPMS)*1•Comes on while driving:Stop in a safe place, check tire pressures, and inflate tire(s) ifnecessary.System MessageComes on along with a beep when a problem is detected. A system message on the driver information interface (DII) appears at the same time. Check the display for more information.*1 - If equippedImmobilizerYour key or remote transmitter cannot be recognized by thevehicle.•Blinks - You cannot start the engine. Turn the ignition switch toLOCK (0)*1, pull the key out (for Canadian models only: apply andhold the brake pedal before turning the ignition on). Then insertthe key and turn it to ON*1 again.•Repeatedly Blinks - The system may be malfunctioning. Haveyour vehicle checked by a dealer.•Do not attempt to alter this system or add other devices to it.Electrical problems can occur.Shift Indicators*1Upshift or downshift when the arrow comes on, for betterefficiency.On/Off IndicatorsThese indicators remind you when an item is on or off.VSA® offVSA®engaged (blinks)LKAS onACC*1 with Low SpeedFollow*1 onTurn signals/hazards onFog lights*1 onHigh beams onExterior lights onAuto High Beam System onECON mode*1onAutomatic brake hold onAutomatic brake activated*1 - If equipped。

The New JettaSleek and sporty, practical and spacious, the New Jetta is more stylish, more aerodynamic and more efficient than ever before. Newly designed front and rear styling reinforces its contemporary appeal, while enhanced features and trim levels provide new levels of elegance and luxury. Designed to take the challenges of the road in its stride, the New Jetta combines responsive steering with refined handling to deliver maximum driving enjoyment, ensuring every journey is a relaxing, stress-free experience. Never has driving been so easy or effortless.optional Bi-xenon headlamps and optional Park Distance Control (front and rear).Made to meet life’s challenges.Irresistible from every angle.The beauty of classic design is its timeless appeal,as exemplified by the New Jetta. Elegant and exciting,the enhanced front design features a revised frontbumper with three chrome trimmed louvres, contouredheadlights and a re-profiled bumper. On Comfortlineand Highline models, standard integrated fog lightsflow seamlessly into the bumper creating a dynamicpresence. Sleeker than ever before, the updated stylingdelivers a 10% improvement in aerodynamics over theprevious model.As you’d expect, what starts at the front concludesat the rear, with a redesigned boot lid featuring anaerodynamically efficient lip extending into the sidewings, a reshaped bumper and stylish new rear lightclusters. The sleek, sculptured bodylines exude styleand charisma, giving the New Jetta itscharacteristic identity.An inner world of peace and order.No question about it, the world is moving faster, life is more pressured and it’s hard to stay in control. Unless you’re sitting in the New Jetta. Here, everything is exactly where you would expect it to be, ergonomically arranged and intuitively to hand, providing a stress-free haven of tranquillity and order. The multifunction computer displays important driving information, such as current or average fuel consumption and the status of your connected mobile phone.Intelligent systems to help keep you safe. Travel in style. Arrive in good time.The rear-view camera helps you reverse park by giving you a clear view to the rear of your vehicle via the display of your radio/navigation system, featuring auxiliary lines to help you park and enabling you to recognise even small obstacles such as kerbs. Optional on all models in conjunction with the RCD 510 or RNS 510.Radio/Satellite Navigation RNS 510 SatNav with TFT Display, touch screen, 30-GB harddisk, SD card reader and DVD drive.The parking sensor pack comprises front and rear parking sensors and reverse activated kerb-view adjustment on the passenger’s side door mirror. The parking sensors assist in parking manoeuvres by emitting ultrasonic, audible and visual signals, alerting the driver to any obstacles in the way. In addition, an optical parking display extends the functions of the parking sensors by indicating your position, either on the RCD 510 radio system (Optional on Trendline, standard on Comfortline and Highline) or the RNS 510 radio system (Optional on Trendline, Comfortline and Highline), on the vehicle’s audio display during parking.The RCD 310 DAB radio system/MP3 compatible CD player provides excellentacoustics via eight speakers with an output of 4 x 20 watts. The radio system displays DAB digital information transmitted by the radio station, track display, song titles and artists. It also features an AUX-in socket for connection to an external multimediasource, such as an iPod or MP3 player. Standard on Trendline.The Multi Device Interface (MDI) with USB port enables you to connect and charge a compatible device, while track selection is viewed and selected via the vehicle’s radio system. USB port Standard on all models. USB port with iPod cable optional.Beige interior not available, black interior only.RCD 510 radio/CD player with 6-disc CD changer and SD card reader.Who doesn’t occasionally long to sit back, relax and catch breath? Thanks to the New Jetta’s comfortable interior and exciting new trim levels, you can do this while on the road. Take for example the Highline model, everything has been designed for your total comfort and relaxation, from the Sports comfort seats to the revised dashboard instrumentation and new steering wheel design. Stylish, refined and practical, it all makes for a pleasant journey, ensuring you arrive at your destination refreshed,replenished and re-energised.Sit back, relaxand enjoy the drive.Add a touch of individuality with a stylish choice of wheels.‘Sedona’ 6.5J x 16” alloy wheels with 205/55 R16tyres. Standard on Comfortline.‘Porto’ 7J x 17" alloy wheels with 225/45 R17 tyres and anti-theft wheel bolts. Standard on Highline.‘Navarra’ 6.5J x 16” alloy wheels with 205/55 R16 tyres. Standard on Trendline.‘Lancaster’ 7J x 17” alloy wheels with 225/45 R17 tyres. Optional on Comfortline.Tornado Red Non-Metallic G2G2Toffee Brown Metallic 4Q4Q Moon Rock SilverMetallic 0B0BReflex Silver Metallic 8E8EPure White Non-Metallic0Q0Q Blue Silk Metallic 2B2B Deep Black Pearlescent 2T2T Platinum Grey Metallic 2R2R The perfect finish, inside and out.Optional on Comfortline & Highline “Vienna” Leather Black TWTrendline“Doryc” Black JM Comfortline“Sienna” Black JM Highline“Gloss Black JM Model shown is Jetta Highline with standard 17” Porto alloy wheels, optional metallic paint, optional Bi-xenon headlamps and optional Park Distance Control (front and rear).Think award-winning TSI engines.*Fuel Consumption and Carbon Dioxide Emission Figures. The figures reflected were obtained in accordance with prescribed uniform measuring standards (SANS 20101: 2006 / ECE R101: 2005 in their currently applicable versions) under laboratory type conditions. The measuring standards are stipulated by law. They do not apply to a specific vehicle and are provided to enable comparison between different vehicle models tested using the same uniform measuring standard. The values are accordingly not necessarily representative of real-life driving conditions. Factors such as driving style, vehicle load, road conditions, tyre size, traffic and ambient conditions may result in different fuel consumption and carbon dioxide emission levels to those achieved under the test parameters referred to above. More details are contained in the owner’s manual.The award-winning TSI engine range benefits from combining innovative direct injection technology and turbocharging. This combination works to produce power far more effectively than normally aspirated engines. It’s a level of performance that will surprise you every time you take to the wheel. Precision engineered, the new generation TSI engine range offers outstanding driving enjoyment with the benefit of reduced fuel consumption and CO 2 emissions, which results in less impact on the environment. It’s no wonder Volkswagen’s multi- award-winning TSI engines have won respect all round as they break new ground in the automotive world and set new standards for others to follow. Jetta TSI engines are fitted with a 6-speed manual gearbox or a 7-speed DSG ® and whether it’s the entry-level 1.2 77kW TSI or the 1.4 90kW TSI, all the way up to the supercharged,flagship 1.4 118kW TSI, you’ll enjoy a spirited and refined performance that’s also environmentally friendly.1.4 118kW Highline TSI winning engine for each year.Safety that inspires driving confidence.The road ahead may have its ups and downs, but to ensure that the ups don’t get the best of you, the Hill-Hold control function activates on inclines, keeping your vehicle stationary until pressure is applied to the accelerator pedal. The Hill-Hold function then disengages and allows acceleration. No more rolling back on inclines. Effortless control. Electronic Differential Lock (EDL) makes it easy for you to drive off with the wheels on two differing road surfaces. Built with a level of safety that ensures peace of mind on every journey, the Jetta makes certain that once you are on the road, you remain there. Electronic Stability Programme (ESP), standard across the range, recognises the first signs of a critical situation and intervenes in milliseconds by utilising engine management control systems to stabilise the Jetta. This, in conjunction with ABS (Anti-lock Braking System) and EDL (Electronic Differential Lock), make for one of the safest and most secure driving experiences. It’s no wonder the New Jetta has been awarded a 5 star Euro NCAP safety rating. Euro NCAP organises crash-tests and provides motoring consumers with a realistic and independent assessment of the safety performance of some of the most popular cars sold in Europe. So relax and enjoy the drive, knowing that Volkswagen putsyou and your family’s safety first. Always.The Jetta is the ultimate realisation of the Das Auto brand philosophy. Das Auto means The Car, and is Volkswagen’s brand ambition to produce the best car in every vehicle class. TSI technology combines impressive performance with lower fuel consumption and emissions. The *Dual-zone climatronic air conditioning creates superior levels of in-cabin comfort that allows each passenger to define their own temperature level. Innovative features like separate daytime running lights, Cruise Control, *Bluetooth cellphone preparation and *Park Distance Control maximise driving pleasure. Nothing has been left unconsidered. From the Rain Sensor to the manual “Coming home/Leavinghome” Lights On Function, the Jetta is at the forefront of innovation and technological excellence.*Features optional on certain models.Think Blue fora greener future.With the Jetta, you can liberate your inner driver and mother nature. The Jetta uses cutting edge technology to deliver on Volkswagen’s determination to protect the environment. Pioneering technologies like Turbo Stratified Injection (TSI), Direct Shift Gearbox (DSG®) and Turbocharged Direct Injection (TDI) are the pillars of Think Blue – Volkswagen’s brand vision of creating efficient and sustainable vehicles for all. The engineering dynamics employed in common rail diesel injection technology produces cleaner, more refined and efficient combustion, for improved performance and fuel consumption. TSI petrol engines blend the best of Volkswagen’s TDI diesel and FSI (Fuel Stratified Injection) petrol technology to be more compact, high-powered and fuel efficient. There’s no need to choose between performance and economy – the cleaner TSI engines have a smaller impact on the environment, are kinder to your pocket, and, best of all, offer outstanding performance. Thanks to the Jetta and Think Blue, the future is looking greener than ever.Think Blue.Volkswagen Service ®Genuine Parts & Accessories ®With 106 Volkswagen Dealerships in South Africa, Namibia and Botswana, you can be assured that, no matter where you are, top quality parts and service will be available, helping you get back on the road sooner. You can expect nothing less from one of the world’s leading car brands. Visit a Volkswagen Dealer and test drive this remarkable example of German engineering today. You can find a comprehensive list of VolkswagenDealerships on our website: vw.co.za/dealersNobody knows your Volkswagen better than we do.Peace of mind included as standard.Volkswagen Financial Services is a division of WesBank, a division of FirstRand Bank Limited. An authorised Financial Services and Credit Provider. NCRCP20When purchasing and insuring a vehicle it makes sense to enlist the help of a trusted partner. Volkswagen Financial Services’ team of dedicated advisers will assist with every aspect of the vehicle purchasing and insuring process, making it as quick and easy as possible. Volkswagensure is a comprehensive range ofaffordable motor insurance products available to Volkswagen owners. Brought to you by Volkswagen Financial Services, Volkswagensure is underwritten by The Hollard Insurance Company Ltd. All Volkswagen Financial Services products are designed to provide you with a hassle free motoring experience and are conveniently available from any Volkswagen Dealer in South Africa. With Volkswagen Financial Services, driving home your Jetta will be easier and faster than you ever imagined.Volkswagen Financial Services ®VolkswagenSureCall centre: 0800 204 638Volkswagen Financial ServicesCall centre: 0861 111 172Every Volkswagen driver is unique.This information was effective as at November 2014 and is subject to change without notice.Visit us at vw.co.za©Volkswagen South AfricaThis has been printed on unbleached fully recyclable paper. Please consider the environment and recycle.。

DrivingLow Speed Braking Control *Using sonar sensors located on the front and rear bumpers, and the front grille, this system detects if there is danger of a potential collision with a wall or other obstacle during normal driving or when the accelerator pedal is depressed with too much force. The system then assists in avoiding collisions and reducing damage from impact through assistive braking and/or assistive driving power suppression.1Low Speed Braking Control *If the Low Speed Braking Control activates in a situation where you do not want automatic brake application (such as when the vehicle is between two railroad crossing gates), simply press the brake pedal to deactivate the system and then continue to drive as intended.3WARNINGThe Low Speed Braking Control System cannot avoid all collisions and may not reduce damage in each situation where the accelerator is mistakenly or aggressively pressed. Overreliance on the system may result in a collision with serious injury or death. Always check your surroundings, your shift position, and your pedal use.Driver remains responsible for safely operating the vehicle.Driving■Assistive brakingAssistive braking provides a visual and audible alert when the vehicle is moving between approximately 1 and 6 mph (2 and 10 km/h) and there is the possibility of a collision with a detected wall or other obstacles, as well as providing assistance with braking.If the only rear sensors are turned off using the parking sensor system, the assistive braking is not working when reversing.2Turning off All Rear Sensors P.619■How the System Works1Low Speed Braking Control *For directions on the proper handling of the sonar sensors, please refer to the following page.2Sonar Sensors * P.600The vehicle will release the brake and start moving a few seconds after the system is activated. To keep the vehicle stopped, keep the brake pedal depressed or put the transmission into P .In order to prevent the system from activating when not needed, always turn it off during vehiclemaintenance, when loading on ships, trucks, and so on, or when using a chassis dynamometer, free rollers for inspection or when washing the car in conveyor type car wash machine.Audible AlertBeepBeepThe vehicle applies brakeDriver depresses brake pedalRemove brake after maintaining stationary positionStopDriving■Assistive driving power suppressionWhen the vehicle is stopped or moving at less than 6 mph (10 km/h) and there is an obstacle such as a wall detected near the front of or back of the vehicle, if the accelerator pedal is depressed more than necessary, the system will inform you with a visual and audible alert. At the same time, the system will prevent sudden forward or backwards movement by limiting the output of the engine, then assistive braking will activate nearby the obstacle.Assistive driving power suppression will not activate in the following situations.When moving forward:When on a steep slope or the shift position is in P , R , or N .When reversing:When on a steep slope or the shift position is in a position other than R .If the only rear sensors are turned off using the parking sensor system, the assistive driving power suppression is not working when reversing.2Turning off All Rear Sensors P.619DrivingWhen you turn the system on and off, do the following.1.Press the safety support switch.2.Roll the right selector wheel to the symbol and push it.u A message appears on the driverinformation interface when the system turns on or off.u A check mark appears in the box and the color of the symbol changes to green when the system is on. The check mark disappears and the color of thesymbol changes to gray when the system is off.The system is turned on every time you start the engine, even if you turned it off the last time you drove the vehicle.■System On and Off1System On and OffYou can also select safety support content from the driver information interface.2Driver Information Interface (Right Side Area) P.142The system may temporarily turn off after reconnecting the battery.The system will automatically turn ON after the vehicle has been moving at over 12 mph (20 km/h) for some time.If the system does not turn on, have your vehicle checked by a dealer.Safety Support SwitchDrivingConditions for assistive driving power suppression.•When the accelerator is no longer depressed.•When the accelerator is depressed for approximately four seconds.•When the brake pedal is depressed.•When the steering wheel is turned and a collision avoided.Conditions for assistive braking cancellation.• A certain amount of time has passed since activation.The system may not operate correctly in the following conditions:■Examples of obstacles the sonar sensor cannot detect•Obstacles that do not reflect sound waves well, such as people, snow, cloth,sponges, etc.•Thin obstacles such as fences, bicycles, sign posts, etc.•Short or small obstacles.•Obstacles immediately in front of the bumper.•Moving objects or obstacles that suddenly enter the road.•Obstacles that are not perpendicular to the ground.■Conditions for Cancellation■Low Speed Braking Control System Conditions and Limitations1Conditions for CancellationAfter Low Speed Braking Control has activated once, it will not activate again for the same obstacle.They can be activated again after driving for a certain distance after last activation.Low Speed Braking Control activates separately when moving forward and reversing. (For example, if it activates when moving forward, it can be activated again immediately if reversing.)However, if assistive braking has been activated, in order to activate assistive driving power suppression again, it is necessary to drive for a certain distance to reset the system.Driving ■Examples of situations where the sonar sensor cannot detect obstacles •The sonar sensor is dirty (covered by snow, water, mud, etc.).•The vehicle is too hot or cold.•The steering wheel is turned sharply when approaching the obstacle at an angle.■Examples of other cases where the system may not work correctly •The vehicle is tilted due to heavy load or suspension modifications.•An abnormal tire or wheel condition (incorrect sizes, varied sizes or construction, improperly inflated, compact spare tire, etc.).•Bad weather conditions such as heavy rain, fog, snow, sandstorms, etc.•The ambient temperature/humidity is too high or low.•When going down a very steep slope.•When close to other vehicles with sonar sensors or other objects that emit ultrasonic waves.■Situations where the system may activate even without risk of a collision •When passing through short or narrow gates.•When driving on uneven surfaces, grassy areas, or places with steps.•When a sloped pillar or wall is protruding from a high position.•When there are obstacles next to the road.•When driving toward flags, curtains, tree branches, railroad crossing bars, etc.•When driving on flooded roads.DrivingLow Speed Braking Control *Using sonar sensors located on the front and rear bumpers, and the front grille, this system detects if there is danger of a potential collision with a wall or other obstacle during normal driving. The system then assists in avoiding collisions and reducing damage from impact through assistive braking.1Low Speed Braking Control *If the Low Speed Braking Control activates in a situation where you do not want automatic brake application (such as when the vehicle is between two railroad crossing gates), simply press the brake pedal to deactivate the system and then continue to drive as intended.3WARNINGThe Low Speed Braking Control System cannot avoid all collisions and may not reduce damage in each situation where the accelerator is mistakenly or aggressively pressed. Overreliance on the system may result in a collision with serious injury or death. Always check your surroundings, your shift position, and your pedal use.Driver remains responsible for safely operating the vehicle.Driving The Low Speed Braking Control provides a visual and audible alert when the vehicleis moving between approximately 1 and 6 mph (2 and 10 km/h) and there is thepossibility of a collision with a detected wall or other obstacles, as well as providingassistance with braking.If the only rear sensors are turned off using the parking sensor system, the LowSpeed Braking Control is not working when reversing.2Turning off All Rear Sensors P.619■How the System Works1Low Speed Braking Control*For directions on the proper handling of the sonarsensors, please refer to the following page.2Sonar Sensors* P.600The vehicle will release the brake a few seconds afterthe system is activated. Keep the brake pedaldepressed.In order to prevent the system from activating whennot needed, always turn it off during vehiclemaintenance, when loading on ships, trucks, and soon, or when using a chassis dynamometer, freerollers for inspection or when washing the car inconveyor type car wash machine.The vehicle RemoveStopDrivingWhen you turn the system on and off, do the following.1.Press the safety support switch.2.Roll the right selector wheel to the symbol and push it.u A message appears on the driverinformation interface when the system turns on or off.u A check mark appears in the box and the color of the symbol changes to green when the system is on. The check mark disappears and the color of thesymbol changes to gray when the system is off.The system is turned on every time you start the engine, even if you turned it off the last time you drove the vehicle.■System On and Off1System On and OffYou can also select safety support content from the driver information interface.2Driver Information Interface (Right Side Area) P.142The system may temporarily turn off after reconnecting the battery.The system will automatically turn ON after the vehicle has been moving at over 12 mph (20 km/h) for some time.If the system does not turn on, have your vehicle checked by a dealer.Right Selector WheelSafety Support SwitchDriving A certain amount of time has passed since activation.The system may not operate correctly in the following conditions:■Examples of obstacles the sonar sensor cannot detect•Obstacles that do not reflect sound waves well, such as people, snow, cloth,sponges, etc.•Thin obstacles such as fences, bicycles, sign posts, etc.•Short or small obstacles.•Obstacles immediately in front of the bumper.•Moving objects or obstacles that suddenly enter the road.•Obstacles that are not perpendicular to the ground.■Conditions for Cancellation■Low Speed Braking Control System Conditions and Limitations1Conditions for CancellationAfter Low Speed Braking Control has activated once,it will not activate again for the same obstacle.They can be activated again after driving for a certaindistance after last activation.Low Speed Braking Control activates separately whenmoving forward and reversing. (For example, if itactivates when moving forward, it can be activatedagain immediately if reversing.)Driving ■Examples of situations where the sonar sensor cannot detect obstacles •The sonar sensor is dirty (covered by snow, water, mud, etc.).•The vehicle is too hot or cold.•The steering wheel is turned sharply when approaching the obstacle at an angle.■Examples of other cases where the system may not work correctly •The vehicle is tilted due to heavy load or suspension modifications.•An abnormal tire or wheel condition (incorrect sizes, varied sizes or construction,improperly inflated, compact spare tire, etc.).•Bad weather conditions such as heavy rain, fog, snow, sandstorms, etc.•The ambient temperature/humidity is too high or low.•When going down a very steep slope.•When close to other vehicles with sonar sensors or other objects that emit ultrasonic waves.■Situations where the system may activate even without risk of a collision •When passing through short or narrow gates.•When driving on uneven surfaces, grassy areas, or places with steps.•When a sloped pillar or wall is protruding from a high position.•When there are obstacles next to the road.•When driving toward flags, curtains, tree branches, railroad crossing bars, etc.•When driving on flooded roads.。

uu Operating the Switches Around the Steering Wheel u LightsControls LightsThe lights will turn on automaticallydepending on the ambient brightness. Theycan also be switched on and off manually.The exterior lights will switch on automaticallywhen the light switch is set to AUTO whilethe power mode is in ON.■Manual operationHeadlights/parking lights:Turn the light switch to .Parking lights:Turn the light switch to .Headlight/parking lights off:Turn the light switch to OFFand release it while the transmission is inP or theparking brake is applied.u The lights will come back on automatically when:•The light switch is turned to OFF again and released.•The transmission is changed out of P or the parking brake is released.■Headlights/Parking Lights1LightsWhen the lights are on, the lights on indicator in theinstrument panel will be on.2Lights On Indicator P.961Headlights/Parking LightsWhen the parking lights are on, the side marker, tail,and rear license plate lights will also switch on.Do not leave the lights on when the engine is offbecause it will cause the battery to discharge.When the light switch is turned to or andthe power is turned to OFF, a beeper sounds whenthe driver’s door is opened.When the light switch is turned to AUTO and theambient light levels are low, the headlights andparking lights will switch on if you unlock a door.They will switch off when the door is locked.If you sense that the level of the headlights isabnormal, have the vehicle inspected by a dealer.uu Operating the Switches Around the Steering Wheel u LightsControlsWhen the headlights are on, push the lever forward. Pull the lever back to return to low beams.■Flashing the high beamsPull the lever back to switch on the high beams.u Release the lever to return to low beams.■High Beams1Headlights/Parking LightsThe light sensor is in the location shown below. Do not cover this light sensor with anything; otherwise, the automatic lighting system may not work properly.You can adjust the auto light sensitivity as follow:2Settings * P.1232How to Customize the Vehicle Settings P.357Setting The exterior lights come on when the ambient light is atMaxHighMid Low MinU.S. modelsBrightDarkModels with 7-in. Color TouchscreenModels with 9-in. Color Touchscreenuu Operating the Switches Around the Steering Wheel u LightsControls The turn signals can be used when the power mode is in ON.direction you want to turn, and the turn signal will blink.and release it, the turn signal will blink 3times.u If you lightly push the lever in theopposite direction while it is blinking, theblinking will stop.■Turn Signals1Turn SignalsThe turn signal indicator on the instrument panel willblink when the external turn signal blinks.2Indicators P.86uu Operating the Switches Around the Steering Wheel u LightsControlsThe headlights automatically come on when the wipers are used several times within a certain number of intervals with the headlight switch in AUTO .The headlights automatically go off a few minutes later if the wipers are stopped.The headlights, all other exterior lights, and the instrument panel lights turn off 15 seconds after you set the power mode to VEHICLE OFF, take the remote with you, and close the driver’s door.If you set the power mode to VEHICLE OFF with the headlight switch on, but do not open the door, the lights turn off after 10 minutes (3 minutes, if the switch is in the AUTO position).The lights turn on again when you unlock or open the driver’s door. If you unlock the door, but do not open it within 15 seconds, the lights go off. If you open the driver’s door, you will hear a reminder chime alerting you that the lights are on.■Headlight Integration with Wipers■Automatic Lighting Off Feature1Headlight Integration with WipersThis feature activates while the headlights are off in AUTO .The instrument panel brightness does not change when the headlights come on.At dark ambient light levels, the automatic lighting control feature turns on the headlights, regardless of the number of wiper sweeps.You can turn the headlight integration with wipers function on and off.2Settings * P.1232How to Customize the Vehicle Settings P.357Models with 7-in. Color TouchscreenModels with 9-in. Color Touchscreen1Automatic Lighting Off FeatureYou can change the headlight auto off timer setting.2Settings * P.1232How to Customize the Vehicle SettingsP.357Models with 7-in. Color TouchscreenModels with 9-in. Color Touchscreenuu Operating the Switches Around the Steering Wheel u LightsControls The parking/daytime running lights come on when the following conditions have been met:•The power mode is in ON.•The headlight switch is AUTO or.•The parking brake is released.The lights remain on even if you set the parking brake. Setting the power mode toVEHICLE OFF will turn off the daytime running lights.While the vehicle is stopped, if you turn the light switch toOFF and release it, thedaytime running lights will turn off. When the transmission is changed out of Pand the parking brake is released, the lights will come on again. Otherwise, if thelight switch is once more turned to OFF, the lights will come on again.■Daytime Running Lights1Daytime Running LightsThe daytime running lights come on dimmer whenthe headlight switch is in than when it is inAUTO. In AUTO, if the ambient brightness is dark,the low beam headlights come on.uu Operating the Switches Around the Steering Wheel u Auto High-BeamControlsAuto High-BeamThe front wide view camera detects the light sources ahead of the vehicle such as the lights of a preceding or oncoming vehicle, or street lights. When you are driving at night, the system automatically switches the headlights between low beam and high beam depending on the situation.When all of the following conditions have been met, the auto high-beam indicator comes on and the auto high-beam is activated.•The power mode is in ON.•The light switch is in AUTO .•The lever is in the low beam position.•The headlights have been automatically activated.•It is dark outside the vehicle.If the auto high-beam indicator does not come on even when all the conditions have been met, carry out the following procedure and the indicator will come on.1Auto High-BeamThe auto high-beam system does not always operatein every situation. This system is just for assisting the driver. Always observe your surroundings and switch the headlights between high beam and low beam manually if necessary.If you find the timing of beam changes inconvenient for driving, change the headlight beams manually.The range and the distance at which the camera can recognize varies depending on conditions surrounding your vehicle.Regarding the handling of the camera mounted to the inside of the windshield, refer to the following.2Front Wide View Camera P.525For the auto high-beam to work properly:•Do not place an object that reflects light on the dashboard.•Keep the windshield around the camera clean. When cleaning the windshield, be careful not to apply the windshield cleanser to the camera lens.•Do not attach an object, sticker or film to the area around the camera.•Do not touch the camera lens.If the camera receives a strong impact, or repairing of the area near the camera is required, consult a dealer.■How to Use the Auto High-BeamLight SwitchAuto High-Beam Indicatoruu Operating the Switches Around the Steering Wheel u Auto High-BeamControls ■Automatic switching between high-beam and low-beamWhen auto high-beam is active, the headlights switch between high beam and lowbeam based on the following conditions.1How to Use the Auto High-BeamIn the following cases, the auto high-beam systemmay not switch the headlights properly or theswitching timing may be changed. In case of theautomatic switching operation does not fit for yourdriving habits, please switch the headlights manually.•The brightness of the lights from the preceding oroncoming vehicle is intense or poor.•Visibility is poor due to the weather (rain, snow,fog, windshield frost, etc.).•Surrounding light sources, such as street lights,electric billboards and traffic lights are illuminatingthe road ahead.•The brightness level of the road ahead constantlychanges.•The road is bumpy or has many curves.•A vehicle suddenly appears in front of you, or avehicle in front of you is not in the preceding oroncoming direction.•Your vehicle is tilted with a heavy load in the rear.•A traffic sign, mirror, or other reflective objectahead is reflecting strong light toward the vehicle.•The oncoming vehicle frequently disappears underroadside trees or behind median barriers.•The preceding or oncoming vehicle is a motorcycle,bicycle, mobility scooter, or other small vehicle.The auto high-beam system keeps the headlight lowbeam when:•Windshield wipers are operating at a high speed.•The camera has detected a dense fog. Switching to high beam:All of the following conditionsmust be met before the highbeams turn on.•Your vehicle speed is 25 mph(40 km/h) or more.•There are no preceding oroncoming vehicle withheadlights or taillights turnedon.•There are few street lights onthe road ahead.Switching to low beam:One of the following conditionsmust be met before the low beamsturn on.•Your vehicle speed is 15 mph(24 km/h) or less.•There is a preceding oroncoming vehicle withheadlights or taillights turnedon.•There are many street lights onthe road ahead.uu Operating the Switches Around the Steering Wheel u Auto High-BeamControls■Manual switching between high-beam and low-beamIf you want to manually switch the headlights between high beam and low beam,follow either of the procedures below. Note that when you do this, the auto high-beam indicator will turn off and the auto high-beam will be deactivated.Using the lever:Pull the lever toward you for flashing the high beams then release it within about one second while driving.u To reactivate the auto high-beam, pull the lever toward you for flashing the high beams then release it while driving. The auto high-beam indicator will come on.Using the light switch:Turn the light switch to .u To reactivate the auto high-beam, turn the light switch to AUTO when thelever is in the low beam position, the auto high-beam indicator will come on.1How to Use the Auto High-BeamHow to turn off the Auto High-Beam System You can turn the auto high-beam system on and off.2Settings * P.1232How to Customize the Vehicle Settings P.357If the Some driver assist systems cannot operate: Camera temperature too high message appears:•Use the climate control system to cool down the interior and, if necessary, also use defroster mode with the airflow directed toward the camera.•Start driving the vehicle to lower the windshield temperature, which cools down the area around the camera.If the Some driver assist systems cannot operate: Clean front windshield or poor viewing condition. message appears:•Park your vehicle in a safe place, and clean the windshield. If the message does not disappear after you have cleaned the windshield and driven for a while, have your vehicle checked by a dealer.Models with 7-in. Color TouchscreenModels with 9-in. Color Touchscreen。

DrivingBrake SystemUse the parking brake to keep the vehicle stationary when parked. When the parking brake is applied, you can manually or automatically release it.■To applyThe electric parking brake can be applied any time the vehicle has battery, no matter which position the power mode is in.Pull the electric parking brake switch up gently and securely.u The indicator in the switch comes on.u The parking brake and brake system indicator (red) comes on.■To releaseThe power mode must be in ON in order to release the electric parking brake. 1.Depress the brake pedal.2.Press the electric parking brake switch.u The indicator in the switch goes off.u The parking brake and brake system indicator (red) goes off.Manually releasing the parking brake using the switch helps your vehicle start slowly and smoothly when facing downhill on steep hills.■Parking Brake1Parking BrakeYou may hear the electric parking brake systemmotor operating from the rear wheel area when you apply or release the parking brake. This is normal.The brake pedal may slightly move due to the electric parking brake system operation when you apply or release the parking brake. This is normal.You cannot apply or release the parking brake if the battery goes dead.2If the Battery Is Dead P.727If you pull up and hold the electric parking brake switch while driving, the brakes on all four wheels are applied by the VSA ® system until the vehicle comes to a stop. The electric parking brake then applies, and the switch should be released.Electric Parking Brake SwitchElectric Parking Brake Switchuu Braking u Brake SystemDriving ■Automatic parking brake feature operationIf the automatic parking brake feature has been activated:•The parking brake is applied automatically when you set the power mode toVEHICLE OFF.•To confirm that the parking brake is applied, check if the parking brake and brakesystem indicator (red) is on.2Activating and deactivating the automatic parking brake feature P.618■To release automaticallyDepressing the accelerator pedal releases the parking brake.Use the accelerator pedal to release the parking brake when you are starting thevehicle facing uphill, or in a traffic jam.Gently depress the accelerator pedal.When on a hill, it may require moreaccelerator input to release.u The parking brake and brake systemindicator (red) goes off.You can release the parking brake automatically when:•You are wearing the driver’s seat belt.•The engine is running.•The transmission is not in P or N.1Parking BrakeIn the following situations, the parking brakeautomatically operates.•When the vehicle stops with the automatic brakehold system activated for more than 10 minutes.•When the driver’s seat belt is unfastened whileyour vehicle is stopped and brake hold is applied.•When the engine is turned off, except by Auto IdleStop system, while brake hold system is applied.•When there is a problem with the brake holdsystem while brake hold is applied.•When the vehicle stops more than 10 minuteswhile ACC with Low Speed Follow is activated.•When the driver’s seat belt is unfastened whileyour vehicle is stopped automatically by ACC withLow Speed Follow.•When the engine is turned off, except by Auto IdleStop system, while ACC with Low Speed Follow isactivated.Models with Adaptive Cruise Control (ACC) withLow Speed FollowAccelerator Pedaluu Braking u Brake SystemDrivingDepress the accelerator pedal while releasing the clutch pedal releases the parking brake.Use the accelerator pedal to release the parking brake when you are starting the vehicle facing uphill, or in a traffic jam.Gently depress the accelerator pedal and release the clutch pedal.u The parking brake and brake system indicator (red) goes off.The parking brake automatically releases as you depress the accelerator pedal when:•You are wearing the driver’s seat belt.•The engine is running.•The transmission is not in N .1Parking BrakeIf the parking brake cannot be released automatically, release it manually.When the vehicle is traveling uphill, the accelerator pedal may need to be pressed farther toautomatically release the electric parking brake.The parking brake cannot be released automatically while the following indicators are on:•Malfunction indicator lamp •Transmission system indicatorThe parking brake may not be released automatically while the following indicators are on:•Parking brake and brake system indicator (red)•VSA ® system indicator •ABS indicator•Supplemental restraint system indicatorThe clutch pedal is fully depressed before gently depress the accelerator pedal and release the clutch pedal.Manual transmission modelsuu Braking u Brake SystemDriving ■Activating and deactivating the automatic parking brake featureWith the power mode is in ON, carry out the following steps to either activate ordeactivate the automatic parking brake feature.1.Put the transmission into P.2.Without depressing the brake pedal, pull up and release the electric parking brakeswitch.u Check that the parking brake and brake system indicator (red) has come on.3.Pull up and hold the electric parking brake switch. When you hear a beepingsound, release the switch and within 3 seconds pull up and hold the switch again.4.When you hear a sound indicating that the procedure is completed, release theswitch.u Two beeps indicates that the feature has been activated.u One beep indicates that the feature has been deactivated.u When you have completed activating the feature, the parking brake willremain applied after you turn off the engine.u To confirm that the parking brake is applied, check if the parking brake andbrake system indicator (red) is on.If you need to temporarily deactivate the feature while putting your vehicle througha conveyor type car wash, you can follow the procedure explained below.1.Depress the brake pedal and bring the vehicle to a stop.2.Set the power mode to VEHICLE OFF and then within 2 seconds push down theelectric parking brake switch.u Activation and deactivation settings for the feature will not be affected.u Before temporarily deactivating the feature, make sure to first turn off bothAdaptive Cruise Control (ACC) with Low Speed Follow and the automaticbrake hold system.u To confirm that the parking brake is applied, check if the parking brake andbrake system indicator (red) is on.1Parking BrakeIn cold climates, the parking brake may freeze inplace if applied.When parking the vehicle, chock the wheels andmake sure the automatic parking brake feature isdeactivated.Also, when putting your vehicle through a conveyor-type car wash or when having your vehicle towed,deactivate the automatic parking brake feature andleave the parking brake released.uu Braking u Brake SystemDrivingYour vehicle is equipped with disc brakes at all four wheels. A vacuum power assist helps to reduce the effort needed on the brake pedal. The brake assist system increases the stopping force when you depress the brake pedal hard in anemergency situation. The anti-lock brake system (ABS) helps you retain steering control when braking very hard.2Brake Assist System P.6242Anti-lock Brake System (ABS) P.623■Foot Brake1Foot BrakeCheck the brakes after driving through deep water, or if there is a buildup of road surface water. If necessary, dry the brakes by lightly depressing the pedal several times.If you hear a continuous metallic friction sound when applying the brakes, this is caused by the brake wear indicator rubbing on the brake rotor and indicates that the brake pads need to be replaced. Have the vehicle checked by a dealer. If you hear only anoccasional squeak or squeal when you initially apply the brake pedal, this may be normal and caused by high frequency vibration of the brake pads against the rotating brake disc.Constantly using the brake pedal while going down a long hill builds up heat, which reduces the brake effectiveness. Apply engine braking by taking your foot off the accelerator pedal and downshifting to a lower gear/speed position. With manual transmission use a lower gear for greater engine braking.Do not rest your foot on the brake pedal while driving, as it will lightly apply the brakes and cause them to lose effectiveness over time and reduce pad life. It will also confuse drivers behind you.uu Braking u Brake SystemDriving Keeps the brake applied after releasing the brake pedal until the accelerator pedal ispressed. You can use this system while the vehicle is temporarily stopped, like attraffic lights and in heavy traffic.■Automatic Brake Hold1Automatic Brake Hold3WARNINGActivating the automatic brake hold systemon steep hills or slippery roads may stillallow the vehicle to move if you removeyour foot from the brake pedal.If a vehicle unexpectedly moves, it maycause a crash resulting in serious injury ordeath.Never activate the automatic brake holdsystem or rely on it to keep a vehicle frommoving when stopped on a steep hill orslippery roads.3WARNINGUsing the automatic brake hold system topark the vehicle may result in the vehicleunexpectedly moving.If a vehicle moves unexpectedly, it maycause a crash, resulting in serious injury ordeath.Never leave the vehicle when braking istemporarily kept by automatic brake holdand always park the vehicle by putting thetransmission in P and applying the parkingbrake.Continuously variable transmission models Automatic Brakeuu Braking u Brake SystemDrivingKeeps the brake applied after releasing the brake pedal until you shift into one of the gears other than N and:•Release the clutch pedal on a level road or when facing downhill.•Release the clutch pedal and depress the accelerator pedal when facing uphill.You can use this system while the vehicle is temporarily stopped, like at traffic lights and in heavy traffic.1Automatic Brake HoldWhile the system is activated, you can turn off the engine or park the vehicle through the same procedure as you normally do.2When Stopped P.625Whether the system is on, or the system is activated, the automatic brake hold turns off once the engine is off.You may hear an operating noise if the vehicle moves while the automatic brake hold system is in operation.The system turns off if the engine stalls while automatic brake hold is active or the system is on.Manual transmission models1Turning on the systemMake sure to turn off the automatic brake hold system before using an automated car wash.uu Braking u Brake SystemDriving ■The system automatically cancels when:•You engage the parking brake.•You depress the brake pedal and put the transmission into P or R.■The system automatically cancels and the parking brake is applied when:•Braking is kept for more than 10 minutes.•The driver’s seat belt is unfastened.•The engine is turned off.•There is a problem with automatic brake hold system.•The engine stalls.■Turning off the automatic brake hold systemWhile the system is on, press the automaticbrake hold button again.u The automatic brake hold systemindicator goes off.If you want to turn off automatic brake holdwhile the system is in operation, press theautomatic brake hold button with the brakepedal depressed.。

零件中英文对照Replacement Parts / Repair Parts 备用零件LCD Screen 液晶Touch Screen / Digitizer 触摸屏LCD Assembly 液晶总成Battery 电池Flex Cable 排线Keypad / Keypad Flex Cable 按键排线Audio Earphone Flex Cable 音频排线Charging Port Dock Connector Flex Cable 尾插排线Proximity Light Sensor Flex Cable 感应排线Home button 返回键Power Button 开关键Mute/Silent Button 静音键Housing / Back Cover 后盖Metallic / Metal Brushed Housing 金属拉丝后盖Middle Plate 中板Middle Bezel / Frame 中框Motor / Vibration Motor 马达Full Housing / Faceplates 全套壳Front Facing Camera 前置摄像头Back Camera 后置摄像头Speaker / Loud Speaker 喇叭Earpiece speaker 听筒Microphone 麦克风Ringer Buzzer 振铃器SIM Card Tray 卡托Headphone Jack Hole 耳机孔Glass Screen Lens 镜面SIM Card Holder / Connector SIM卡座Memory Card Holder 内存卡卡座Battery FPC Plug 电池座Screw 螺丝Anti-dust Mesh 防尘网Adhesive Strip Sticker 贴纸Ejection Pin 取卡针Mainboard / Motherboard 主板配件及电子产品壳子主要有：硬壳（hard case）清水套（TPU case/ gel case）硅胶（silicone case）皮套( leather case)，贴钻壳（diamond/rhinestone/diamante/Swarovski case）边框（bumper case）水晶壳（crystal case）混合壳(hybrid case) (defender)直插皮套（pouch）臂带（armband）防水袋（waterproof bag）枪套( holster leather case )钱包型皮套( wallet leather case )工艺：拉丝(brushed)电镀(electroplating/ plating)磨砂(matte/frosted)光面(glossy)喷油( rubberized）纹路：碳化纤维( carbon fiber )豹纹( leopard )斑马纹( zebra )鳄鱼纹( crocodile / croco )蛇纹( snake )蜥蜴纹( lizard )木纹( wood grain )凯蒂猫(Hello Kitty)史迪奇（Stitch）松弛熊（Rilakkuma）米奇（Mickey）米妮（Minnie）唐老鸭（Donald Duck）蓝精灵（Smurf）奥特曼(Ultraman)乔巴超人（Chopper Man）美乐蒂（My Melody）阿拉蕾（Arale ）泰迪熊（Teddy bear）芭比（Barbie）蒙奇奇(Monchhichi)马里奥(Mario)海贼王（One Piece）品牌：LV, Chanel (香奈儿) , Gucci (古琦), Coach（寇兹）, Burberry（巴宝莉）, Paul Frank (大嘴猴), Polo Shirt(马球衫), Ferrari(法拉利), Audi(奥迪), Lamborghini (兰博基尼，爱马仕（Hermes），Monster Beats (魔声耳机)屏贴主要分四种（screen protector）:透明（clear），磨砂（matte/anti-glare/frosted），镜面（mirror），防偷窥（privacy/ anti-spy）特殊的: 钻石（diamond）3D效果(3D effect)充电相关：充电器( charger )适配器( adapter )电源适配器( power adapter )车充( car charger )旅行充/墙充( wall charger/travel charger/home charger)座充( cradle dock desktop cradle/ charger dock )电池充电器( battery charger )充电器套件( charger kit )移动电源( portable power bank/emergency battery )充电皮套( charger case )USB数据线( USB data cable )充电线( data sync charger cable )转接头/ 器( converter adapter )延长线( extension cable/extender cable )音频线( audio cable )网线( network cable )电池：battery备用电池( battery replacement )后备电池( external battery / backup battery )太阳能后备电池( solar external battery )厚电加后盖( extended battery with battery door cover )耳机：earphone /headphone/headset入耳式耳机( in-ear headphone )头戴式耳机(over-ear / on-ear headphone )立体声耳机( stereo earphone )蓝牙耳机( Bluetooth earphone )带麦和线控的耳机(earphone / headphones with mic and remote )灯：lighting / lampLED灯( LED light )吊灯( ceiling lighting lamp )灯泡( bulb light )灯管( light bar )灯条( strip light )车灯( car light / lamp/bulb )灯头转换器( lamp adapter converter )手电筒( flashlight / flashlight torch )闪光灯( flashlight )镭射手电筒( laser flashlight )前头灯( headlight )聚光灯( spotlight )探照灯( searchlight )桌灯( table light )光板( light panel )电子表( digital watch )LED表( LED watch )运动手表( sport watch )石英表( quartz watch )手表( wrist watch )相机：camera便携式摄像机( camcorder )柔光箱( soft box )柔光罩( flash diffuser )滤光镜( filter lens )滤光镜保护器( filter lens protector )光学玻璃保护膜( optical glass led screen protector ) 相机镜头盖( camera lens cap )镜头罩( lens hood )数码相框( digital photo frame )热靴( hot shoe )三脚架( tripod )其他：触摸笔( touch pen / stylus )模型机( dummy / fake / display / model phone )音箱( speaker )记忆卡( memory card )微型SD / TF卡( Micro SD/TF Card )读卡器( card reader )包装盒( package / packing box )键盘( keyboard )蓝牙键盘( Bluetooth keyboard )支架( stand / holder )U盘( USB flash disk )防盗支架( anti-shoplifting display stand )腕带( wrist strap )工具( tool )修理工具( repair tool )螺丝刀( screw driver )望远镜( telescope )望远镜摄像头( telescope camera lens )接收器( receiver )手镯( bracelet )游戏手柄( game controller )车载支架( car holder/car mount )喷头/ 花洒( shower head )消毒器/杀菌器( sterilizer )鱼探器( fish finder )训狗器( dog training )狗脖套( dog collars )显微镜( microscope )温度计( thermometer )罗盘( compass )冷却风扇( cooling fan )心跳监视器( heart rate monitor )功率平衡腕( power balance wristband bracelet ) 提醒器( reminder )血压监护仪( blood pressure monitor )奶瓶( milk feeding bottle )收音机( radio )钱包( wallet / purse )存储箱( storage box )手提包( handbag )酒精测试仪( breath alcohol tester )呼气测醉器( breathalyzer )录像机(DVR)? ( digital video record )摄像手表( spy watch )秤( scale )电子秤( electronic scale )追踪器( tracker )GPS追踪器( GPS tracker )遥控装置( remote control )触发器( trigger )泊车传感器系统( car parking sensor system ) 尖嘴钳( needle nose pliers )USB集线器(USB Hub )电源开关( power switch )插头( plug adapter )锁( lock )传感报警器( sensor alarm )收发器(transceiver )摄像头( camera )视频捕获卡(video capture card )电子狗( dongle )投影仪( projector )路由器( router )网卡( network adapter )网线接头( network connector )电缆测试器( cable tester ) 端口集线器( port hub )音频分配器( audio splitter )。

Features Use the audio/information screen to customize certain features.With the power mode in ON, press the button, and then select GeneralSettingsand select a setting item.■How to Customize the General Settings1Customized FeaturesWhen you customize settings:•Make sure that the vehicle is at a complete stop.•Shift to P.To customize features detail, refer to the following.2Customization flow P.3772System P.3812Smartphone Connection P.3842Connections P.3852Display P.3862Sound P.3862Camera P.3872Voice Control P.387Audio/Information Screenuu Customized Features uContinuedFeatures■Customization flowPress thebutton.System Sounds SystemDate Format Time FormatText-to-Speech Phone Calls Automatic Time Zone *System VolumesLanguageDefaultSelect General Settings .Time Zone(Select time zone)*Not available on all modelsuu Customized Features u Features*Not available on all modelsuu Customized Features uFeaturesContinueduu Customized Features u Features*1:Models with BOSE AMP*2:Models with Normal AMPuu Customized Features uContinuedFeatures■System*1:Default Setting*2:Default Setting for U.S. models*3:Default Setting for Canadian modelsCustomizable FeaturesDescriptionSelectable Settings Date & TimeSet Date & TimeAutomatic Date & TimeSelects ON to have the GPS automatically adjust the clock. Select OFF to cancel this function.ON *1/OFF Set Date Adjusts date.2Adjusting the Clock P.146Day /Month /Year Set Time Adjusts time.2Adjusting the Clock P.146Hour /Minute AM /PM Time ZoneAutomatic Time Zone *Sets the audio system to automatically adjust the clock when driving through different time zones.ON *1/OFF(Select time zone)Changes the time zone manually.—Auto Daylight Saving Time Sets the clock to update based on daylight savings time.ON *1/OFF Date Format Select a date format.MM/DD/YYYY *2/DD/MM/YYYY *3/YYYY/MM/DD Time FormatSelect a time format.12H *1/24H*Not available on all modelsuu Customized Features uFeatures*1:Default SettingCustomizable FeaturesDescriptionSelectable Settings Language Changes the driver information interface and audio/information screen language separately.English *1/Español /Français Touch Panel SensitivitySets the sensitivity of the touch panel screen.High /Normal *1System VolumesSystem Sounds Sets the system sound volume level.—Text-to-SpeechSets the text-to-speech volume level.—Navigation Guidance Sets the navigation guidance volume level.—Phone Calls Sets the phone call volume level.—DefaultResets all System Volumes settings to default values.Data Sharing SettingTurns the data sharing setting on and off.2Start Up P.272ON *1/OFF Refuel Recommend *Turns the refuel recommend function on and off.2Refuel Recommend P.439ON *1/OFF*Not available on all modelsuu Customized Features uContinued FeaturesCustomizable Features Description Selectable SettingsAbout StatusDisplays the Android setting items.—Legal InformationModel NumberAndroid VersionKernel VersionBuild NumberFactory Data Reset Resets all the settings to their factory default.2Defaulting All the Settings P.399Continue/CancelDetail Information App ManagerDisplays the Android system memory and appsinformation.—uu Customized Features uFeatures ■Smartphone ConnectionCustomizable Features Description Selectable Settings Apple CarPlay+Connect New DevicePairs a new phone to Apple CarPlay.2Phone Setup P.425—(Saved Devices)Connects, disconnects, or deletes a paired phone.2Phone Setup P.425—Android Auto+Connect New DevicePairs a new phone to Android Auto.2Phone Setup P.425—(Saved Devices)Connects, disconnects, or deletes a paired phone.2Phone Setup P.425—uu Customized Features uContinuedFeatures■Connections*1:Default Setting*2:Appears only when Apple CarPlay or Android Auto is connected wirelessly.Customizable FeaturesDescriptionSelectable Settings Wi-FiChange ModeChanges the Wi-Fi mode.Network *1/Smartphone *2/OFF(Available Networks/Connected Devices)Displays the available network(s) or current connected device(s).—OptionsAdd Network Adds a new network to connect Wi-Fi.—Saved Networks Saves the connected network.—SetupNetwork SSID Sets the network name.—SecurityDisplays the network security.—Password Sets password for require entering password when connecting Wi-Fi device to the network.—Wi-Fi BandDisplays the Wi-Fi band.—BluetoothOptionsBluetooth Turns the Bluetooth ® on and off.ON *1/OFFPriority DeviceDisplays the priority device.—+Connect New Device Pairs a new phone to HFL.2Phone Setup P.425—(Saved Devices)Connects, disconnects, or deletes a paired phone.2Phone Setup P.425—Features ■Display■Sound*1:Models with BOSE AMP*2:Models with Normal AMPCustomizable Features Description Selectable Settings Brightness Changes the brightness of the audio/information screen.—Contrast Changes the contrast of the audio/information screen.—Black Level Changes the black level of the audio/information screen.—DefaultResets all customized settings for the brightness,contrast, and black level.—Customizable Features Description Selectable Settings Bass / TrebleTrebleAdjusts the settings of the audio speakers’ sound.2Adjusting the Sound P.290—MidrangeBassAudio Zones & Balance / Fader*1Bose Centerpoint*1Bose Dynamic Speed Compensation*1Balance / Fader*2Speed Volume Compensation*2ContinuedFeatures■Camera*1:Default Setting■Voice Control*1:Default SettingCustomizable FeaturesDescriptionSelectable Settings Rear CameraFixed GuidelineShows the guideline that does not move with the steering wheel.2Multi-View Rear Camera P.593ON *1/OFFDynamic GuidelineShows the guideline that moves with the steering wheel.2Multi-View Rear Camera P.593ON *1/OFFCross Traffic Monitor Shows arrows on the rear camera image to indicate vehicles approaching from the sides.2Cross Traffic Monitor P.589ON *1/OFFCustomizable FeaturesDescriptionSelectable Settings Voice Control Mode Selects a mode of the voice portal screen.2Voice Control Operation P.293Assist /Normal *1FeaturesWith the power mode in ON, press the button, and then select Vehicle Settingsand select a setting item.■How to Customize the Vehicle SettingsAudio/Information ScreenContinuedFeatures■Customization flowPress thebutton.Blind Spot InfoTPMS Calibration *Select Vehicle Settings .Rear Sensor Setting*Not available on all modelsFeaturesFeatures *Not available on all modelsContinuedFeatures ■TPMS Calibration*■Driver Assist System Setup*1:Default SettingCustomizable Features Description Selectable Settings TPMS CalibrationCancels/Calibrates the tire pressure monitoring system (TPMS).2Tire Pressure Monitoring System (TPMS) P.480Calibrate/CancelCustomizable Features Description Selectable SettingsForward Collision WarningDistanceSelects distance for Forward Collision Warning audible and visualalerts.2Collision Mitigation Braking System TM (CMBS TM) P.495Long/Normal*1/ShortACC Forward Vehicle DetectBeepTurns On/Off audible notification when vehicle has moved in/out ofadaptive cruise control range.2Adaptive Cruise Control (ACC) with Low Speed Follow P.513ON/OFF*1Road Departure MitigationSettingSelects operating mode of the Road Departure Mitigation system.2Road Departure Mitigation System P.554Narrow/Normal*1/Wide/Warning OnlyLane Keeping AssistSuspend BeepSwitches the LKAS and Traffic Jam Assist alert beeps on and off.2Lane Keeping Assist System (LKAS) P.5332Traffic Jam Assist P.545ON/OFF*1*Not available on all modelsContinuedFeatures*1:Default SettingCustomizable Features DescriptionSelectable Settings Blind Spot InfoSelects On/Off the blind spot information system audible alert.2Blind Spot Information System P.487Audible And Visual Alert *1/Visual Alert Traffic Sign Recognition System Display Setting Displays the traffic sign recognition system on the instrument panel.2Traffic Sign Recognition System P.562Display *1/NoneTraffic Sign Recognition System Speed Limit WarningEnables over speed limit warning when speed limit is exceeded.2Traffic Sign Recognition System P.562ON /OFF *1Speed Limit Warning Threshold SettingWhen Traffic Sign Recognition System Speed Limit Warning setting is on, select speed limit warning threshold based on personal preference.2Traffic Sign Recognition System P.562Speed Limit *1/Speed Limit +3mph /Speed Limit +5mph /Speed Limit +10mph (When mph is selected)Speed Limit *1/Speed Limit +5km/h /Speed Limit +10km/h /Speed Limit +15km/h(When km/h is selected)Driver Attention MonitorChanges the setting for the driver attention monitor.2Driver Attention Monitor P.126OFF /Tactile Alert /Tactile And Audible Alert *1Rear Sensor SettingSelect to turn the rear parking sensor ON or OFF. This selection will also affect the rear Low Speed Braking Control if equipped.2Parking Sensor System * P.5842Low Speed Braking Control * P.507ON *1/OFF*Not available on all modelsFeatures■Meter Setup*1:Default SettingCustomizable Features DescriptionSelectable SettingsAdjust Outside Temp. DisplaySelects to adjust outside temperature reading by a few degrees.2Outside Temperature P.115-5°F ~ ±0°F *1 ~ +5°F (U.S.)-3°C ~ ±0°C *1 ~ +3°C (Canada)"Trip A" Reset TimingSelects the timing to reset Trip A.2Range / Fuel / Trip Meter P.1212Speed / Time / Trip Meter P.123When Fully Refueled /IGN OFF /Manually Reset *1"Trip B" Reset TimingSelects the timing to reset Trip B.2Range / Fuel / Trip Meter P.1212Speed / Time / Trip Meter P.123When Fully Refueled /IGN OFF /Manually Reset *1Adjust Alarm Volume Changes volume level of all system warnings, door opening warning and indicator.High /Mid *1/Low Fuel Efficiency Backlight Turns the ambient meter feature on and off.ON *1/OFF Turn By Turn Auto DisplayTurns the pop-up warning ON/OFF in the turn-by-turn navigation in the driver information interface.2Turn-by-Turn Directions P.125ON *1/OFFSpeed/Distance Units Selects the trip computer units.2No Content P.132km/h · km /mph · miles *1 (U.S.)km/h · km *1/mph · miles (Canada)Rear Seat Reminder Turns the Rear Seat Reminder feature on and off.ON *1/OFFContinuedFeatures■Driving Position Setup*1:Default Setting■Keyless Access Setup*1:Default SettingCustomizable Features DescriptionSelectable Settings Memory Position Link Turns the driving position memory system on and off.ON *1/OFF Seat Position Movement At Entry/Exit Moves the seat rearward when you get in/get out of the vehicle. Changes the setting for this feature.ON *1/OFFCustomizable Features DescriptionSelectable SettingsDoor Unlock Mode Changes which doors unlock when you grab the driver’s door handle.Driver Door Only *1/All Doors Keyless Access Light Flash Causes some exterior lights to flash when you unlock/lock the doors.ON *1/OFF Keyless Access Beep Causes the beeper to sound when you unlock/lock the doors.ON *1/OFF Remote Start System ON/OFFTurns the remote engine start feature on and off.ON *1/OFF Lockout Protection Changes the settings for the lockout protection function.ON *1/OFFuu Customized Features uFeatures■Lighting Setup*1:Default SettingCustomizable Features DescriptionSelectable Settings Auto High BeamTurns on/off auto high beam function.ON *1/OFFInterior Light Dimming TimeSelects the length of time the interior lights stay on after doors are closed.2Interior Lights P.21660sec /30sec *1/15secHeadlight Auto OFF Timer Selects the length of time the exterior lights stay on after you close the driver's door.2Automatic Lighting Off Feature P.19160sec /30sec /15sec *1/0sec Auto Light Sensitivity *Changes the timing for the headlights to come on.Max /High /Mid *1/Low /Min Auto Headlight On with Wiper On Selects On/Off headlight function and wiper operation when the headlight is in AUTO setting.2Headlight Integration with Wipers P.190ON *1/OFF*Not available on all modelsuu Customized Features uContinuedFeatures■Door/Window Setup*1:Default SettingCustomizable Features DescriptionSelectable Settings Auto Door LockChanges the setting for the automatic locking feature.With Vehicle Speed *1/Shift From P /OFFAuto Door Unlock Changes the setting for when the doors unlock automatically.All Doors When Driver’s Door Opens *1/All Doors When Shifted to Park /All Doors With IGN OFF /OFF Walk Away Auto Lock Changes the settings for the auto lock function when you walk away from the vehicle.ON /OFF *1Lock PresettingTurns on/off the lock presetting function.ON *1/OFF Keyless Lock Answer Back Turns on/off flash of exterior lights when doors are locked/unlocked by the keyless remote.2Using the Remote Transmitter P.157ON *1/OFF Remote Window Control Turns the remote window control on and off.ON *1/OFFuu Customized Features uFeatures ■Power Tailgate Setup*1:Default Setting■Predictive Eco Assist**1:Default Setting■Maintenance Info.Customizable Features Description Selectable Settings Keyless Open Mode Changes the keyless setting for when the power tailgate opens.Anytime*1/When Unlocked Power Open By OuterHandleChanges the setting to open power tailgate by tailgate outer handle.ON (Power/Manual)*1/OFF(Manual Only)Hands Free Access Function*Changes the setting to open power tailgate by a swift forward in andout kicking motion under the rear bumper.ON*1/OFFCustomizable Features Description Selectable Settings Predictive Eco Assist Turns the Predictive Eco Assist on and off.ON*1/OFFCustomizable Features Description Selectable Settings Maintenance Info.Resets the maintenance information.2Maintenance Minder TM P.603Select Reset Items*Not available on all modelsuu Customized Features u Defaulting All the SettingsFeaturesDefaulting All the SettingsReset all the menu and customized settings as the factory defaults.1.Press thebutton.2.Select General Settings .3.Select System .4.Select Factory Data Reset .u A confirmation message appears on the screen.5.Select Continue to reset the settings.6.Select Continue again to reset the settings.u The system will reboot.1.Press the button.2.Select Vehicle Settings .3.Select Default .4.Select Yes .■Defaulting General Settings1Defaulting All the SettingsWhen you transfer the vehicle to a third party, reset all settings to default and delete all personal data.If you perform Factory Data Reset , it will reset the preinstalled apps to their factory default.If you perform Factory Data Reset , you cannot use the HondaLink ® because it goes offline.2HondaLink ® P.320■Defaulting Vehicle Settings。