圆锥滚子轴承尺寸表
- 格式：docx
- 大小：37.86 KB
- 文档页数：8
圆锥滚子轴承尺寸表
以下是___的产品检验尺寸表（/7200E系列），已经经过审核和批准。
序号。产品型号。总装高度。尺寸公差。外圈高度。尺寸公差。内圈高度。尺寸公差。外径尺寸。尺寸公差。内径尺寸。尺寸公差
1..11.75.+0.20.-0.20.-0.12.10.-0.15.35.-0.20.15.-0.15
2..13.25.+0.20.-0.20.-0.12.11.-0.15.40.-0.20.17.-0.15
3..15.25.+0.20.-0.20.-0.12.14.-0.12.47.-0.20.20.-0.15
4..16.25.+0.20.-0.20.-0.12.15.-0.12.52.-0.20.22.-0.15
5..17.25.+0.20.-0.20.-0.12.16.-0.12.62.-0.20.25.-0.15
6..18.25.+0.20.-0.20.-0.12.17.-0.12.72.-0.20.30.-0.15
7..19.75.+0.20.-0.20.-0.12.18.-0.12.80.-0.20.36.-0.20
8..20.75.+0.20.-0.20.-0.12.19.-0.12.85.-0.20.38.-0.20
9..21.75.+0.20.-0.20.-0.12.20.-0.12.90.-0.20.42.-0.20
10..22.75.+0.20.-0.20.-0.15.21.-0.15.100.-0.20.45.-0.20
11..23.75.+0.20.-0.20.-0.15.22.-0.15.110.-0.20.50.-0.20
12..24.75.+0.20.-0.20.-0.15.23.-0.15.120.-0.20.55.-0.20 13..26.25.+0.20.-0.20.-0.15.24.-0.15.125.-0.20.60.-0.20
14..27.25.+0.20.-0.20.-0.15.25.-0.15.130.-0.20.65.-0.20
15..28.25.+0.20.-0.20.-0.15.26.-0.15.140.-0.20.70.-0.20
16..30.5.+0.20.-0.20.-0.20.28.-0.20.150.-0.20.75.-0.20
17..32.5.+0.20.-0.20.-0.20.30.-0.20.160.-0.20.80.-0.20
18..34.5.+0.20.-0.20.-0.20.32.-0.20.170.-0.20.85.-0.20
19..37.+0.20.-0.20.-0.20.34.-0.20.180.-0.20.90.-0.20
20..39.+0.20.-0.20.-0.20.36.-0.20
21..41.+0.20.-0.20.-0.20.38.-0.20
本产品检验尺寸表适用于/7200E系列，由___编制并经过审核和批准。每个产品型号的总装高度、外圈高度、内圈高度、外径尺寸和内径尺寸等参数均在表格中列出，并标注了相应的尺寸公差。请注意，本表格中的尺寸公差是指允许的最大偏差值，其中“+”表示上限，“-”表示下限。
___ /7300E series bearings。The table includes the product
model number。overall height。outer ring height。inner ring
height。outer diameter。and inner diameter ns。along with their
___.
The table shows that the overall height of the bearings
increases from 14.25mm for the model to 51.50mm for the model。The tolerances for the overall height are all within +0.20mm.
The outer ring height of the bearings ranges from 11mm for
the model to 39mm for the model。The tolerances for the outer
ring height are all within -0.12mm.
The inner ring height of the bearings ranges from 11mm for
the model to 39mm for the model。The tolerances for the inner
ring height are all within -0.12mm.
___ 34mm for the model to 100mm for the model。The
tolerances for the outer diameter are within +0.20mm for all
models except the model。which has a tolerance of -0.20mm.
___ the bearings ranges from 15mm for the model to 60mm
for the model。The tolerances for the inner diameter are within
+0.20mm for all models except the model。which has a tolerance
of -0.20mm.
Overall。___ /7300E series bearings。which can be used to
___.
Product ___ (/7500E Series)
Product Model Number Total Assembly Height ___
1 17.25 -0.014/-0.012 12.75 -0.014/-0.012 14.25 -0.014/-0.012 40 -0.20 17 -0.20
2 19.25 -0.014/-0.012 14.75 -0.014/-0.012 15.25 -0.014/-0.012 47 -0.20 20 -0.20
3 19.25 -0.014/-0.012 15.25 -0.014/-0.012 16.25 -0.014/-0.012 52 -0.20 25 -0.20
4 21.25 -0.016/-0.012 16.75 -0.016/-0.012 17.25 -0.016/-0.012 62 -0.20 30 -0.20
5 24.25 -0.016/-0.012 18.75 -0.016/-0.012 19.25 -0.016/-0.012 72 -0.20 35 -0.20
6 24.75 -0.016/-0.012 19.75 -0.016/-0.012 20.25 -0.016/-0.012 80 -0.20 40 -0.20 7 24.75 -0.016/-0.012 20.75 -0.016/-0.012 21.25 -0.016/-0.012 85 -0.20 45 -0.20
8 24.75 -0.016/-0.012 21.75 -0.018/-0.012 22.25 -0.018/-0.012 90 -0.20 50 -0.20
9 26.75 -0.018/-0.012 22.75 -0.018/-0.012 23.25 -0.018/-0.012 100 -0.20 55 -0.20
10 29.75 -0.018/-0.015 24.75 -0.018/-0.015 25.25 -0.018/-0.015 110 -0.20 60 -0.20
11 32.75 -0.018/-0.015 26.75 -0.018/-0.015 27.25 -0.018/-0.015 120 -0.20 65 -0.20
12 33.25 -0.018/-0.015 27.75 -0.018/-0.015 28.25 -0.018/-0.015 125 -0.20 70 -0.20
13 33.25 -0.020/-0.015 28.75 -0.020/-0.015 29.25 -0.020/-0.015 130 -0.20 75 -0.25
14 37.25 -0.025/-0.015 29.75 -0.025/-0.015 30.25 -0.025/-0.015 140 -0.20 80 -0.25
15 39.25 -0.025/-0.015 31.75 -0.025/-0.015 32.25 -0.025/-0.015 150 -0.20 85 -0.25
16 41.25 -0.025/-0.020 33.75 -0.025/-0.020 34.25 -0.025/-0.020 160 -0.20 90 -0.30 17 43.25 -0.030/-0.020 35.75 -0.030/-0.020 36.25 -0.030/-0.020 170 -0.20 95 -0.30
18 47.25 -0.030/-0.020 39.75 -0.030/-0.020 40.25 -0.030/-0.020 180 -0.20 100 -0.30
Note: Any paragraphs with us errors have been deleted。The
remaining paragraphs have been ___.
产品型号：、、、
总装高度：63.50、67.51、71.51、75.51
尺寸：+0.20/-0.20
这四个产品型号的总装高度分别为63.50、67.51、71.51、75.51，尺寸方面允许的偏差为+0.20/-0.20.
注意：文章中存在大量表格和编号，但没有明确的描述和解释，因此无法完全理解文章的内容和意图。建议在改写时加入必要的说明和解释。
Product ___ (/xxxxxxxE Series)
