轮机英语10

北极星电力中国电力联盟孤独不孤5854210zzw19890219豆丁5854210汽轮机英语词汇TURBINE VOCABULARYI Power station电站1. power station电站2. power plant电站，发电设备3. utility电力部门4.independent power producer (IPP)独立发电项目，独立发电站5.nuclear power station核电站6. thermal power station火电站7. fossil (fired) power plant化石燃料电站，常规火电站8. combined heat power (CHP) plant热电联供机组9. steam power plant蒸汽电站，蒸汽发电设备10. cogeneration power station热电联供电站11. coal fired power plant燃煤电站12. oil fired power plant燃油电站13. gas filed power plant燃气电站14. LNG power plant (liquefied natural gas)燃液化天然气电站15. BoP (balance of plant)电站辅机16. I&C (instrumentation and control)仪表和控制系统II Turbine透平，涡轮17. Turbine透平，涡轮18. steam turbine汽轮机19. gas turbine燃气轮机20. nuclear turbine核电汽轮机21. fossil turbine火电汽轮机22. industrial turbine工业透平23. cogeneration turbine热电联供透平24. condensing turbine凝汽式汽轮机25. back pressure turbine背压式汽轮机26. extraction turbine抽汽式汽轮机27. extraction condensing turbine抽汽凝汽式汽轮机28. single-extraction turbine单抽汽轮机29. double-extraction turbine双抽汽轮机30. mechanical drive turbine机械驱动汽轮机31. HP (IP, LP) turbine高（中、低）压缸32. sub-critical pressure turbine亚临界汽轮机33. super-critical pressure (SC) turbine 超临界汽轮机34. ultra-super critical (USC) pressure turbine超朝临界汽轮机35. BFPT (boiler feed pump turbine)给水泵汽轮机36. steam turbine with air-cooled condenser（air cooled steam turbine）空冷汽轮机37. reheat turbine再热汽轮机38. double-reheat turbine二次再热汽轮机39. wet steam turbine湿蒸汽汽轮机40. saturated steam turbine饱和蒸汽汽轮机41. full-speed turbine全速汽轮机42. half-speed turbine半速汽轮机43. tandem compound turbine单轴汽轮机44. cross compound turbine双轴汽轮机45. super (over)-high pressure turbine过高压汽轮机46. impulse (type) turbine冲动式汽轮机47. reaction (type) turbine反动式汽轮机48. axial flow turbine轴流透平49. radial flow turbine径流透平50. turbine with axial condenser轴向排汽汽轮机51. turbine with horizontal joint带有水平中分面的汽轮机52. turbine with vertical joint带有垂直中分面的汽轮机53. double flow turbine两排汽汽轮机54. triple flow turbine三排汽汽轮机56. single-casing turbine单缸汽轮机57. double-casing turbine双缸汽轮机58. turbine proper汽轮机本体59. oil turbine 油透平60. hydraulic turbine水轮机61. marine steam turbine船用汽轮机62. aeroderivative gas turbine航改式燃气轮机63. stationary steam turbine电站汽轮机64. auxiliary turbine辅助透平III Rotary parts回转件65. rotor转子66. rigid rotor刚性转子67. flexible rotor挠性转子68. solid (forged) rotor (monobloc rotor)整锻转子69. welded rotor焊接转子70. (hollow) drum (type) rotor鼓型转子71. built-up rotor组装转子72. rotor without center bore无中心孔转子73. HP-LP integrated rotor高/低压一体化转子74. shafting (shaft)轴系75. HP (IP, LP) rotor高（中、低）压转子76. thrust collar推力盘77. journal轴颈78. section of rotor转子区段79. (first, second ) critical speed一阶（二阶）临界转速80. extension shaft (spacer)中间轴，延伸段81. coupling联轴节82. flexible coupling挠性联轴节83. rigid coupling刚性联轴节84. semi-flexible coupling半挠性联轴节85. half coupling联轴节半部86. integral (forged) coupling整体（锻制）联轴节87. shrunk-on coupling红套联轴节88. spigot（rabbet）止口89. disk (disc) 叶轮90. rim (steeple)轮缘（枞树型叶根槽）91. hub轮毂92. body（web）轮体93. T （fir tree-type ) groove T型（枞树型）叶根槽94. balance hole (plane, weight, plug)平衡孔（平衡平面，平衡配重，平衡旋塞）95. keyway键槽96. disk of constant stress (conical profile)等强度（锥形）叶轮97. disk of constant thickness等厚度叶轮98. shrunk-on disk红套叶轮99. blade叶片100. moving (rotating, rotor) blade动叶101. bucket 动叶102. straight (tapered, twisted) blade直叶片（变截面叶片，扭曲叶片）103. last stage (last but one, penultimate) blade末级叶轮（次末级叶片）104. last (locking , gate) blade (piece)末叶片（锁紧叶片，锁紧件）105. free-stand blade自由叶片106. integral shroud blade整体围带叶轮107. triple-pin blade三联叶片 108. bow blade马刀型叶片109. compound lean blade复合弯扭叶片110. concave (pressure) side内弧（压力侧）111. convex (suction) side 背弧（负压侧）112. tenon铆钉头113. leading (inlet) edge 进汽边114. trailing (outlet, exit) edge出汽边115. blade wake叶片尾流116. convergent-divergent channel (CD passage)缩张通道117. brazed (stellite) shield钎焊（斯太立）防蚀片118. lacing hole拉筋孔119. profile (section of blade)叶型，型线部分（叶片截面）120. reaction（degree）反动度121. cascade叶栅122. blade root叶根123. (three teeth, straight, curved ) fir- tree (blade) root（三齿直线/弧形）枞树型叶根 124. ( five finger) fork type (blade) root（五叉）插入式叶根，叉型叶根 125. tee (T-type) root T型叶根126. inverted-T (blade) root倒T型叶根127. straddle-type (blade) root 外包叶根128. straddle inverted T-root 外包倒T型叶根129. dovetail root (serrated root)燕尾型（齿型）叶根130. lacing (tie) wire 拉筋131. (lacing) lug (stub) 拉筋凸台132. loose lacing wire松拉筋133. tubular lacing wire管状拉筋134. shroud (band，cover)围带135. whole circle packed (continuously connected) shroud 整圈连接围带136. integral shroud整体围带137. snubber整体围带138. gauging (throat)喉节比（喉部）139. pitch diameter节径，平均直径140. top diameter（叶片）顶部直径IV. Stationary parts静止件141. casing (cylinder)汽缸，缸体142. outer casing外缸143. inner casing内缸144. single-shell casing单层缸145. double-shell casing双层缸146. cover (upper half)上半部147. base (lower half)下半部148. horizontal (split) joint水平中分面149. (massive) flange（厚）法兰150. (casing) bore（汽缸）洼窝151.fastener (bolt, nut, stud, dowel)紧固件（螺栓、螺母、螺柱、定位销）152. vertical flange垂直法兰153. tightness气密性154. inlet进口155. exhaust排汽口156. exhaust hood 排汽缸157. guide plate导流板158. diffuser扩压管159. flange bolt hole法兰螺栓孔160. shrunk-on ring红套箍环161. combined HP-IP casing高中压合缸162. thermal shield (baffle)挡热板163. single (double) flow HP turbine单流（双流）高压缸164. flow path (steam path)通流部分165.center support system滑键系统166. lug ( foot, pawl)猫爪167. thermal insulation保温设施168. enclosure (lagging)罩壳（外壳）169. diaphragm隔板170. blade ring ( diaphragm carrier)叶片持环，隔板套171. outer (inner) ring (of diaphragm)（隔板）外环（内环，隔板体）172. stationary (stator, guide ,nozzle) blade静叶，导叶，喷嘴173. vane (partition) 静叶174. cast-in (welded-in) diaphragm铸造（焊接）隔板 rotary diaphragm回转隔板 175. nozzle block (chest)喷嘴组（喷嘴室）176. diaphragm deflection隔板挠度177. bearing housing (pedestal)轴承箱178. front bearing housing (standard) 前轴承箱179. rear bearing housing 后轴承箱180. floor(-type) bearing落地式轴承181. bearing轴承182. journal (radial) bearing支持轴承（径向轴承）183. thrust ( axial) bearing推力轴承（轴向轴承）184. tilting pad bearing可倾瓦轴承185. Kingsburg type thrust bearing金斯布里推力轴承186. Babbitt (white metal, bearing metal)巴氏合金187. bearing bush轴承壳体188. bearing body轴承体189. bearing pad轴瓦190. bearing cover (cap) 轴承上半191. 360°bearing整圆轴承192. elliptical bearing椭圆轴承193. three wedge bearing三油楔轴承194. self-aligning bearing自找中轴承195. sleeve bearing套筒式轴承196. sliding bearing滑动轴承197. (oil) pocket (wedge)油袋（油楔）198. oil film油膜199. oil (film) whip油膜振荡200. setting pad (segment)安装瓦块201. working pad (segment)工作瓦块202. oil ring (oil deflector)挡油环203. oil film stiffness油膜刚度204. armored thermocouple铠装式热电偶V. Main Valves主要阀门205. Main (HP) stop valve (MSV)主汽阀206. control (governing) valve (CV, GV)调节阀207. reheat (IP) stop valve(RSV)再热主汽阀208. intercept valve再热调节阀209. Combined main stop/governing valve联合式主汽/调节阀210. butterfly valve蝶阀211. piloted (pre-inlet) valve预启阀212. fast valve快速动作阀213. check (non-return) valve逆止阀214. solenoid valve电磁阀215. motor driven (operated) valve电动阀216.drain valve疏水阀217. diaphragm valve (atmospheric)膜片阀（大气阀）218. relief (exhaust) valve释放阀（放汽阀）219. safety valve安全阀220. extraction valve 抽汽阀221. stop valve截止阀222. flap valve翻板阀223. gate valve闸阀224. steam chest蒸汽室225. (valve) stem阀杆226. (valve) disk (plug)阀碟227. (valve ) seat阀座228. (valve) bonnet (cover)阀帽（阀盖）229. valve casing (chest)阀壳230. (valve) travel (stroke)阀门行程231. cross over (cross under)连通管232. anti-jamming(stick) test防卡涩试验VI. Various systems各种系统(1) Control system (control and protection system)调节系统（调节保安系统） 233. Electro-hydraulic control system电液调节系统234. hydro-mechanical control system液压调节系统235. DEH (digital electro-hydraulic control system)数字式电液调节系统236. electro-hydraulic converter电液转换器237. trip跳闸，脱扣238. actuator执行机构239. servomotor油动机240. pilot (slide, spool) valve滑阀241. piston活塞242. piston rod活塞杆243. (oil) cylinder油缸244. (oil) window油口（窗）245. overlap覆盖度246. emergency governor危急遮断器247. speed governor 调速器248. MSV servomotor 主汽阀油动机249. spring support操纵座250. centrifugal stop bolt撞击子251. LVDT (linear variable differential transformer)线性阀位传感器252. safety test box安全试验盒253. relay继电器，继动器254. relay valve继动滑阀255. axial displacement indicator (transducer)轴向位移指示器（传感器） 256. overspeed protection超速保护257. differential expansion detector (transducer)差胀检出器（传感器） 258 lever杠杆259. (cam type) steam distribution device凸轮式排汽机构260. throttle governing节流调节261. nozzle governing喷嘴调节262. partial admission (degree)部分进汽（度）263.full arc admission全周进汽264. governing (control) stage (Curtis stage) 调节级（复速级）(2) Oil system油系统265. Main oil reservoir (tank)主油箱266. turbine oil透平油267. fire-resistant fluid抗燃油268. lube (lubrication ) oil润滑油269. HP control fluid高压控制油270. pressure (feed) line (pipe)供油管道271. return (relief) line (pipe) 回油管道273. nested pipe （pipe in pipe）system套管式274. demister除油雾器275. fan风机276. mist separator 油污分离器277. oil purifier净油装置，油净化器278. oil filter滤油器279. oil cooler 冷油器280. overflow valve溢流阀281. oil vapour油雾，油气282. main oil pump( shaft driven)主油泵283. impeller（主油泵）叶轮284. switch-over (change-over)切换(3) Gland system汽封系统285. Labyrinth gland 拉别林汽封，迷宫式汽封286. gland housing (casing)汽封体287. gland segment汽封弧段288. gland (sealing) ring 汽封环289. gland strip (comb)汽封片（齿）290. brush sealing刷子汽封291. leaf sealing薄叶汽封292. diaphragm gland隔板汽封293. gland over shroud (tip gland)围带汽封294. shaft gland轴封295. gland steam condenser (cooler)汽封冷却器296. spring-back sealing回弹式汽封297. gland leak-off 漏汽298. gland ejector 汽封抽气器299. packing盘根，填函，汽封300. inner (outer) gland 内侧（外侧）汽封301. gland chamber (pocket) 汽封腔室302. dummy ring (balance piston)平衡环(4) Drain system疏水系统303. (drain) flash tank （疏水）扩容器304. drain port 疏水口305. cascade drain (system)逐级疏水306. drain cooler疏水冷却器(5) Bypass system旁路系统307. capacity容量308. HP (IP) bypass loop高压（中压）旁路回路309. start with bypass system利用旁路系统启动310. desuperheating and reducing device减温减压装置(6) Regenerative system回热系统311. HP heater高压给水加热器（高加）312. LP heater低压给水加热器（低加） deaerator除氧器313. terminal (temperature) difference (TTD) （温度）端差 314. drain subcooler approach (DCA)疏水过冷段315. shell side (design pressure)壳侧（设计压力）316. tube side (design pressure)管侧（设计压力）317. condensing zone冷凝区318. drain subcooling zone疏水过冷区319. direct contact (LP) heater混合式（低压）加热器320. U tube U型管(7) Reheat system再热系统321. Cold reheat line再热冷端管道322. hot reheat line 再热热端管道323. MSR (moisture separator reheater)汽水分离再热器 324. (single) reheat（一次）再热325. double reheat二次再热VII Auxiliaries辅机(1) Condenser凝汽器326. Shell-tube type heat exchanger壳管式热交换器327. surface condenser 表面式凝汽器328. direct contact condenser混合式凝汽器329. shell壳体330. (divided) water box (chamber)（对分）水室331. tube bundle管束332. tube plate (sheet) 管板333. support plate 支承隔板334. tube cleaner管子清洗器335. sponge ball cleaning system海绵球清洗系统336. double-shell condenser双壳体凝汽器337. single pass condenser单流程凝汽器338. air cooling zone空气冷却区339 air (cooled) condenser空冷凝汽器340. vacuum system真空系统341. evacuate 抽真空342. tube expander胀管器343. condensate冷凝水344. hot well (condensate sump)热井345. cooling rate冷却速率346. cleanness 清洁度347. condensate pump凝结水泵348. (condenser) neck（凝汽器）喉部349. expansion joint膨胀接头350. wave type (bellows) compensator波纹管补偿器351. deaerating capacity除氧能力352. subcooling degree过冷度353. non-condensed (condensable) gas不凝结气体354. booster pump增压泵(2) Oil cooler冷油器355. Filter过滤器 strainer滤网356. cartridge滤芯357. vent通风口358. clogging堵塞359. twin-filter双联冷油器360. on－line change-over (switch-over) 在线切换(3) Ejector 抽气器361. Steam jet (air) ejector射汽抽气器362. water jet (air) ejector 射水抽气器363. (water ring) vacuum pump（水环）真空泵364. evacuation 抽真空365. vacuum establishing (forming) 建立真空366. starting ejector启动抽气器367. vacuum breaker真空破坏阀(4) Turning gear (device) or barring gear盘车装置368. Bull gear大齿轮369. driving gear驱动装置370. worm and (worm) gear涡轮蜗杆副371. turning by (every) 180°（每次）盘转180度372. jacking-up oil pump顶轴油泵373. (dis) engagement 啮合（脱开）VIII Operation运行374. Operation mode运行方式 Start (up)启动375. (emergency) shut down （紧急）停机376. daily start- stop (DSS) 日启停377. initial start初次启动378. cold (state) start 冷态启动379. warm start 温态启动380. hot start 热态启动381. extreme hot start极热态启动382. base load (unit) 基荷机组383. cyclic load循环负荷384. peak load峰荷385. peak shaving调峰386. two-shift (operation)两班制（运行）387. cyclic duty capacity变负荷能力388. life cycle（使用）寿命389. life expenditure (CLE)寿命消耗390. life extension 寿命延长391. trip(ping)跳闸392. load tracking (following) capacity负荷跟踪能力393. boiler-turbine coordination control锅炉－汽机协调控制 394. warming暖机395. loading-up (down)升负荷（降负荷）396. unloading甩负荷 397. load throw-off甩负荷398. run up升速 399. run away飞车400. idle running惰行，空负荷运行401. speed up升速402 synchronization同步403. synchronizer同步器404. connect to grid并网405. rolling (by steam)冲转（用蒸汽）406. fixed pressure (start)定压（启动）407. sliding pressure (start)滑压（启动）408. combined (hybrid) fixed/sliding pressure operation定压/滑压混合运行方式 409. routine inspection日常检查410. planned maintenance计划维修411. overhaul (intervel)大修（间隔期）412. forced outage rate (FOR)强迫停机率413. repair检修414. availability可用率415. reliability可靠性416. control room 控制室417. corrosion腐蚀 erosion浸蚀，水涮418. stress corrosion cracking (SCC) 应力腐蚀裂纹419. latch-on (reset)挂闸420. commission调试，试运行，交付使用希望以下的内容对大家有点帮助。

轮机英语词汇目录1）第一部分柴油机Diesel Engine5）第二部分制冷和空调7）第三部分燃、滑油系统及油参数Fuel System ,Lubricating System &Oil Properties10）第4部分泵及其系统Pump &Pumping System11）第5部分船用锅炉Mair Boiler14）第6部分液压甲板机Hydraulic Deck Machinery17第7部分油水处理设备，轴系及推进器，造水机Oil Treatment,Oily Water Separator,Shafting &Propeller,Fresh Water Generator 18）第8部分交流发电机及配电板Alternating Current Generator& Switchboard20）第9部分法规及消防设备Watchkeeping,International Convention &Fire Fighting22）第10 部分维修常用词汇Useful Expressions in Repair List29）工具和量具Tools and Maeasuring Tools34）常用量词与缩写35）金属材料及其制品36）非金属材料及其制品36）化工材料37）电气材料37）油类38）紧固件,管接头39）船型40）船上构造The Structure of A ship第一部分柴油机Diesel Engine二冲程船用柴油机two stroke marine diesel engine四冲程船用柴油机four stroke marine diesel engine高（中，低）速柴油机high(medium, lower)speed engine气缸cylinder气缸盖cylinder cover(cylinder head)苏尔寿发动机Sulzer engineB&W型发动机Burmeister and Wain engine哥塔维根型发动机Gotaverken engine曼恩型发动机M.A.N.engineV型发动机V-type engine直流扫气式发动机uniflow scavenging type engine回流扫气式发动机loop flow scavenging type engine横流扫气式发动机crow-flow scavenging type engine十字头式发动机crosshead engine筒形活塞式发动机trunk-piston engine涡轮增压式发动机turbocharge engine固定部件fixed parts耐磨部件wear parts运动部件moving parts互换部件interchangeable parts气缸套cylinder liner示功阀indicator cock(indicator valve)安全阀safety valve气缸启动阀cylinder air starting valve缸套顶圈head ring for cylinder liner排气阀exhaust valve进气阀air inlet valve(suction valve)气阀传动机构valve driving mechanism顶杆tapper rod推杆push rod摇臂rocker rod (rocking lever)活塞piston十字头式活塞crosshead type piston筒形活塞trunk piston活塞头piston crown(head)活塞裙piston skirt活塞体piston body活塞销piston pin(gudgeon pin)活塞环piston ring气环（压缩环）compression ring刮油环oil scraper ring(oil ring,scraper ring)布油环oil distributing ring耐磨环wear ring活塞环槽piston ring groove活塞冷却水管piston cooling pipe往复管reciprocating pipe伸缩管telescope pipe铰链管articulated pipe活塞杆piston rod活塞杆凸缘piston rod flange活塞杆填料函stuffing box for piston rod活塞杆填料箱gland box for piston rod.packing gland for piston rod填料函壳体stuffing box casing填料函张力弹簧tension spring for stuffing box填料函密封环sealing ring for stuffing box填料函刮油环scraper ring for stuffing box填料函压环pressure ring for stuffing box填料函压盖stuffing box gland十字头cross head十字头销cross head pin十字头销轴承cross head bearing(cross head pin bearing)十字头滑块cross head shoe(guide shoe)十字头导板cross head guide(guide rail,guide way,guide plate)连杆connecting rod连杆小端轴承connecting rod small end bearing连杆大端轴承connecting rod large end bearing;connecting rod bottom end bearing 曲柄销轴承crankpin bearing曲轴crank shaft曲轴臂crank arm曲轴销crank pin曲轴箱crankcase曲轴箱道门crankcase door(crankcase manhole)曲轴箱防爆门crankcase explosion door主轴承main bearing (bed plate bearing)倒挂式主轴承main bearing of under slung type轴承轴瓦上半块bearing bush-upper half轴承衬下半块bearing shell-lower half主轴承撑杆螺栓main bearing stay bolt主轴颈crank shaft journal(main journal)机座bed plate底座横隔板bed plate transverse member机架frame(column,entablature)底角螺栓holding down bolt (anchor bolt)贯穿螺栓through bolt (tie rod,tie bolt)贯穿螺栓护盖protecting covering for tie rod贯穿螺栓导套guide bush for tie rod推力轴thrust shaft推力轴承thrust bearing推力块thrust pad盘车机turning gear废气涡轮增压器exhaust gas turbocharge (turbo-blower)增压系统super charging system机械增压mechanical supercharging单（复）式增压系统single(complex)type super charging system二级增压two-stage supercharging定压增压系统constant pressure charging system脉冲增压系统impulse pressure charging system变压增压variable pressure charging system串联增压super charging in series syatem并联增压super charging in parallel system直流扫气unislow scavenging回流扫气loop scavenging横流扫气cross scavenging气口扫气port scavenging气口-气阀扫气port-valve scavenging扫气口scavenging port排气口exhaust port排气总管exhaust manifold排气管exhaust pipe上止点top dead center(TDC)下止点bottom dead center(BDC)燃烧室combustion chamber吸气行程inlet(suction) atroke压缩行程compression stroke做功行程power (working) stroke排气行程exhaust stroke定时图timing diagram指示功indicated power轴功shaft power示功图indicator power控制系统control system启动控制装置control devic for starting起动装置starting devic主起动阀main starting valve空气压缩机air compressor空气瓶air bottle(air container,air cylinder,air reservoir) 起动手柄starting lever(starting handle)起动空气控制阀starting air control valve起动空气导阀starting air pilot valve起动阀starting valve分级活塞stepped piston起动阀连锁装置starting valve blocking device起动凸轮starting cam起动空气管starting air pipe单凸轮换向装置single cam reversing device双凸轮换向装置double cam reversing device正车凸轮ahead cam正车油缸ahead oil cylinder (ahead oil bottle) 自动停车装置automatic cut-out device空气分配器凸轮air distributor cam转向指示器running direction indicator换向杆reversing lever换向控制杆reversing control lever排气凸轮exhaust cam喷油凸轮fuel cam主起动阀手轮hand wheel for starting valve飞轮flywheel;turning wheel调速器goernor调速装置control device for running the engine 极限调速装置maximum-speed governor gear定速调速装置constant-speed governor gear全制式调速装置variable-speed governor gear机械调速器mechanical governor液压调速器hydraulic governor车钟telegraph凸轮传动机构camshaft transmission gear链条传动chain transmission(chain drive)齿轮传动gear tansmission链轮sprocket (sprocket wheel)惰轮idle wheel备车stand by engine完车finish engine停车stop engine微速前进（后退）dead slow ahead (astern)前进（后退）一slow ahead (astern)前进（后退）二half ahead (astern)前进（后退）三full ahead (astern)紧急前进（后退）三emergency full ahead(astern)起动start倒车reverse空气分配器air distributor气缸注油器cylinder lubricator第2 部分制冷和空调Refrigeration & air conditioning制冷refrigeration空调air conditioning通风ventilation盐水制冷brine refrigeration热电制冷thermoelectric refrigeration蒸汽压缩循环vapour-compression cyle制冷剂refrigerant直接制冷剂primary refrigerant间接制冷剂secondary refrigerant氟利昂freon氟化氢fluorinated hydrocarbon临界温度critical temperature压缩机compressor蒸发器evaporator感温包sensing bulb膨胀阀expansion valve电磁阀solenoid valve干燥器drier/dryer冷凝器condenser储液器liquid receiver油分离器oil seperator中间冷却器inter cooler内部均压装置internal equalizer风冷冷凝器air-cooled condenser双阀座截止阀double seat stop valve手动能量控制阀hand capacity control valve水量调节阀water regulating valve气动薄膜碟阀pneumatic film flap valve出液阀delivery valve出液管outlet pipe外平衡管outer balance pipe半封闭式压缩机semi-enclosed compressor节流阀throttle valve加湿器humidifier回油装置oil-return device回气管return pipe自动水量调节阀automatic water regulating valve自动液压能量控制装置automatic hydraulic capacity control device 压力控制器pressure control压差控制器differential pressure control吸入截止阀suction stop valve吸入滤网suction stainer充液阀charging valve冷凝器进入阀condenser inlet valve冷凝器出液阀condenser outlet valve冷却盘管cooling coil冷库insulted hold空气加热器air heater空气滤清器air cleaner油位检查镜inspection glass for oil level油预热器oil preheater卸载油缸unloading cylinder波纹管bellows制冷剂瓶refrigerant bottle热力膨胀阀thermostatic expansion valve毛细管capillary tube膜片diaphragm阀孔隙orifice恒温器thermostant诱导器inducer背压调节阀back-pressure valve浮动式自动回油阀floating type automatic oil return valve热交换器heat exchanger高压继电器high voltage relay温度调节器humidistat能量调节阀capacity regulator通风机ventilator舱室温度控制器cabin type temperature control排气融霜管discharge defrost pipe液位控制器liquid level control液体分离器liquid separator捡漏灯halide lamp船用臭氧发生器marine ozonizer温包式温度控制器phial type temperature controller湿度控制器humidity controller蒸发盘管evaporator coil tube散热器radiator空气调节器air conditioner二次空气系统secandary air conditioning system中央空调系统central air conditioning system高速诱导式空调系统high speed induction air conditioning system 半导体空调器semi-conductor air conditioner热泵式空调器heat-pump air conditioner窗式空调器window-type air conditioner毛发式气动湿度控制器pneumatic hair humidity controller风管air pipe出风栅outlet grid再加热盘管reheating coil空气干燥室air drying chamber 顶式布风器top ventilator进风栅inlet grid挡水曲板curve flap翅片管tuberculat pipe散热盘管radiator coil tube 挡板baffle翅状散热片fin波形散热片gill单风管系统single duct system 双风管系统twin duct system 分区加热器zone heater终端加热器terminal-heater压力通风plenum第3部分燃，滑油系统及油参数Fuel System ,Lubricating System &Oil Properties燃油系统fuel oil system双层底油舱double bottom fuel tank粗滤器strainer细滤器filter双联细滤器dual oil filter(duplex oil filter)燃油驳运泵fuel transfer pump沉淀柜settling tank分油机oil separator滑油柜/日用油柜lubricating oil tank\daily service tank加热器heater增压泵booster pump三通阀three way valve集油井oil head tank (oil header,oil collector buffer tank ,balance tank) 高压油泵（燃油喷射泵)fuel injection pump柱塞式油泵plunger type fuel injection pump布式油泵Bosch fuel injection pump回油孔fuel return hole进油孔fuel inlet hole柱塞（芯子）plunger柱塞套筒（柱塞导管）plunger guide bush(plunger barrel,plunger load)调节齿杆（调节齿条）control rack(toothed control rod)调节齿圈（调节齿套）control sleeve(control pinion)排油阀fuel delivery valve回油阀式高压油泵spill valve type fuel injection pump进油阀suction valve (spill valve,blowthrough valve)油量调节机构fuel relgulation linkage油泵行程调节杆regulating lever for pump stoke油压调节阀fuel pressure regulating valve保压阀pressure retaining valve高压油管high pressure fuel pipe喷油器fuel injector,fuel valve,fuel injection valve喷油器壳体fuel injector holder(fuel injector housing)喷油嘴injectin nozzle(nozzle)针阀needle valve针阀顶杆spindle溢流管overflow pipe蒸汽加热器steam heater蒸汽加热管steam heating pipe蒸汽加热盘管steam heating coil润滑系统lubricating system干油底壳式润滑dry oil sump type lubrication湿油底壳式润滑wet oil sump type lubrication飞溅润滑splash lubrication中压（低压）润滑系统medium pressure lubrication system (low pressure lubrication system) 气缸润滑cylinder lubrication轴承润滑bearing lubrication气缸注油器oil squirt(cylinder lubricator)吸油管suction duct(suction line)储油箱oil storage tank调节控制杆control lever for adjusting oil油孔oil orifice(oil hole)油道oil way(oil channel)油底壳oil sump(sump tank,crank bilge)污油柜oil sludge tank滑油循环柜circulating lube oil tank滑油粗滤器lube oil strainer滑油泵lube oil pump滑油冷却器lube oil cooler比重（相对密度）specific gravity (relative density)黏度viscosity发火质量ignition quality十六烷值cetane number柴油指数diesel index闪点（开口/闭口）flash point (open /closed)倾点pour point浊点cloud point凝点freezing point残碳值carbon residue灰份ash content水分water content硫分sulphur content热值calorific value机械杂质mechanical impurities油品等级grade of oil馏程distilling rang矾含量vanadium content铝含量alumminium content船用轻柴油marine gas oil (MGO)船用燃料油marine fuel oil(MFO)船用柴油marine diesel oil (MDO)中间燃料油internal fuel oil添加剂additive总酸值total acid number(TAN)强酸值strong acid number (SAN)总碱值total base number (TBN)沉淀物含量sediment抗氧化安定性oxidation resistance抗腐蚀性corrosion极压添加剂extreme pressure additive 黏度指数viscosity index第4部分泵及其系统Pump &Pumping System船用泵marine pump立式泵vertical pump卧式泵horizontal pump单缸泵single cylinder pump双缸泵duplex pump单（双）作用泵single(double)-acting pump单级泵single-stage pump双级泵double-stage pump定量泵constant-delivery pump变量泵constant displacement pump(constant delivey pump) 自吸式泵self-priming pump非自吸式泵none-self priming pump容积式泵displacement pump轴流泵axial-flow pump离心泵centrifugal pump往复泵reciprocating pump活塞泵piston pump柱塞泵plunger pump径向柱塞泵radial plunger pump轴向柱塞泵axial plunger pump回转泵rotary pump叶片泵vane pump单（双）作用叶片泵single(double)-acting pump齿轮泵gear pump水环泵water ring pump内（外）齿轮泵inside(outside)gearing pump螺杆泵screw pum液压泵hydraulic pump径流泵radial-flow pump旋涡泵volute pump喷射泵ejector pump蒸汽直接作用泵direct-acting steam driven pump主机驱动泵min-engine-driven pump冷却水（油）泵cooling water(oil)pump给水泵feed pump备用给水泵donkey feed water pump卫生水泵sanitary pump出灰泵ash-ejecting pump压载水泵ballast pump污水泵sewage pump凝水泵condensate pump引水泵priming pump(primer pump)盐水泵brine pump淡水泵fresh water pump消防泵fire pump舱底水泵bilge pump循环泵circulating pump真空泵vacuum pump驳运泵transfer pump排污泵slusge pump变量泵variable output pump洗仓泵tank cleaning pump增压泵booster pump泵壳pump housing泵体pump body泵缸pump cylinder泵缸套pump line填料箱stuffing box吸入阀suction valve净正吸入压头net positive suction head (NPSH) 系统水头损失system head loss泵浦特性曲线pump characteristic curve排出discharge (delivery)流道liquid path叶轮impeller (vane wheel)扩压管diffuser蜗壳volute管路pipe line旋塞（考克）cock止回阀non-return valve碟形阀butterfly valve闸板阀gate valve转阀rotary(rotating) valve滑阀slide (sliding)valve球形阀globe valve安全阀relief valve速闭阀quick closing valve (strip valve) 集中引水系统central priming system (CPS)第5部分船用锅炉Mair Boiler火（水）管锅炉fire (water) tube boiler立（卧）式锅炉vertical (horizonatal)boiler直（横，弯，盘，指）管锅炉straight(cross,bent,coil,thimble)-tube boiler 废气锅炉exhaust boiler管式锅炉tubular boiler筒形锅炉cylindr boiler (shell type boiler)鼓筒形锅炉drum boiler燃油辅助锅炉oil-burning auxiliary boiler立式横烟管锅炉vertical fire tube boiler卧式三回程火管锅炉horizontal triple-pass fire tube boiler盘管式强制循环废气锅炉coil-tube forced-circulation exhaust boiler人孔门manhole door水包water drum水管联箱water header水冷壁water-cooled wall (water screen, water wall)上升管riser tube下降管down comer后水冷壁rear water wall tube侧水冷壁side water wall tube沸腾联箱steaming header沸水管boiling-water tube炉膛furnace (fire box)炉胆furnace flue炉排fire bar(fire grate)炉门fire door炉衣boiler clothing (boiler lagging)炉墙furnace wall耐火砖衬层fire-brick lining挡烟墙baffle wall给水阀feed water valve给水截止阀feed water stop valve给水止回阀feed water check valve汽鼓（汽锅筒）steam drum汽水分离器steam purifier (steam separator)内给水管internal feed pipe给水离子交换器feed water ion exchanger省煤器（经济器）economizer上部联管upper header下部联管lower header前部联管front header后部联管rear header进口分配联管inlet distributing header出口分配联管outlet distributing header水位表water level gauge玻璃水位表glass water level gauge低位水位表bottom water level gauge远距离水位显示计remote water level indicator水位计分支阀（通汽考克，通水考壳）water level root valve(steam cock,water cock) 光滑管plain tube带肋片的蛇形管coil tube with ribs水位调节器water level regulator低水位保险装置low-water level cut-off device危险水位报警器low-water level alarm热水井hot well热水循环泵hot water regulating pump水处理water treatment上排污阀surface blow-down valve底部排污阀bottom blow down valve上（下）部吹除阀surface(bottom) blow-off valve浮渣盘scum dish烟管smoke tube烟箱smoke chamber(smoke box)烟道smoke flue烟囱chimney(funnel)烟喉furnace uptake牵条stay牵条管stay tube支承管support tube波形管sinuflo tube麻花管swirlyflo tube吹灰器soot blower单层盘管single-layer tube燃烧器oil burner燃油预热器oil preheater雾化器burner atomize (sprayer)雾化片sprayer plate喷油嘴burner tip (nozzle)喷油嘴管架nozzle support喷油嘴体nozzle holder喷孔nozzle hole(nozzle orifice)旋涡室swirl chamber点火器igniter点火喷油嘴ignition nozzle点火变压器ignition transformer预燃室precombustion chamber调风器air register调风门air damper风门throttle (air intake flap)风门伺服器servomotor for throttle regulation 风口draught door风箱burner wind box风机blower手调风门hand regulating throttle空气调温器air attemperator空气扩散盘air diffuse disk导流器air director空气调节器air regulator (air register)强制通风机force draught fan火焰检测器flame detector火口fire hole(combustion head)比例操作器proportional ratio apparatus压力比例操作器pressure ratio regulator停汽阀steam stop valve集汽管steam receive蒸汽分配器steam distributor阻汽器steam trap过热器super-heater减热器desuper heater旋风汽水分离器cyclone steam separator除氧器deaerator第6部分液压甲板机械Hydraulic Deck Machinery液压泵hydraulic pump径向柱塞泵radial plunger pump中央阀center valve配油轴oil distribution shaft配油盘oil distribution disc配油套oil distribution sleeve配油口oil distribution port配油壳oil distribution casing配油阀oil distribution valve浮动环floating ring压力管pressure pipe伺服活塞srevo-piston差动活塞differential piston倾斜盘swash plate液压放大器hydraulic amplifier液压马达hydraulic motor高速小扭矩油马达high speed low torque oil motor齿轮式（叶片式，轴向柱塞式）油马达gear-type (vane-type,axial-plunger-type)oil motor 低速大扭矩油马达low speed high torque oil motor柱塞式油马达plunger-type oil motor径向柱塞式油马达radial-plunger-type oil motor单作用径向柱塞式油马达single-acting radial-plunger-type oil motor轴向双斜盘式油马达axial-double-tilting frame type oil motor液压油缸hydraulic oil cylinder单作用柱塞油缸single-acting plunger oil cylinder摆动油缸oscillating oil cylinder差动油缸differential oil cylinder转叶式油缸rotary-vane-type oil cylinder定叶fixed vane转叶rotary vane密封条sealing strip定子stator转子totor压力控制阀pressure control valve顺序阀sequence valve直控～direct-control valve单向～one-way valve(check valve)卸载～off-load valve遥控～telecontrolled valve液控～hydraulically controlled valve减压阀pressure-reducing valve定压～constant pressure valve定差～constant difference valve定比～constant ratio valve溢流阀overflow valve先导式～pilot valve直动式～direct-acting valve差动式～differential valve流量控制阀flow control valve节流阀throttle valve调速阀speed-regulating valve方向控制阀direction control valve直通式～straight one-way valve直角式～angle one way valve手动截止阀hand stop valve (hand cut-off valve)双路油压自锁阀double-circuit oil pressure self-closing valve换向阀change-over valve (change valve)电磁～electro-magnetic valve电液～electro-hydraulic valve转阀（滑阀）ritary valve (side valve)三位四通阀three-position four-way valve主阀main valve辅阀auxiliary valve先导阀pilot valve阻尼孔damper hole节流缝隙throttle slot舵机steering gear定量泵开式系统open oil system of the constant delivery pump变量泵闭式系统closed oil system of the variable delivery pump撞杆式舵机ram type steering gear转叶式舵机rotary vane type steering gear工况选择阀operating mode selector valve手动旁通阀hand by-pass valve反馈杆feed back rod自锁阀self-locking valve防浪阀storm valve舵rudder舵柱rudder post舵柄rudder tiller舵托（承）rudder carrier舵叶rudder blade舵杆rudder stock撞杆ram操纵系统control system机械杠杆反馈式追随机构follow-up system of the mechanical lever feedback type应急手动操纵装置emergency hand control device浮动杆floating lever副杠杆auxiliary lever遥控操舵装置telemotor steering gear起货装置cargo handing gear起货绞车cargo winch回转起货机crane吊扬索（千斤索）topping lift吊货杆boom(derrick boom)吊臂jib(crane jib)吊臂止动器jib stopper机械制动器machanicalbrake防索松保护器slack wire protection变幅绞车luffing winch货物定位装置cargo psotler差动型限位开关differential limit switich旋转绞车slewing winch带式刹车band brake旋转底盘slewing rim起锚机windlass止链器cable stopper锚anchor锚链anchor chain(anchor cable,chain cable)锚链轮chain lifter(cable lifter,cable holder)锚链舱chain locker链轮止动器chain lifter brake离合器clutch绞盘capstan绞盘卷筒capstan barrel带缆卷筒warping drum锚链卷筒chain drum绞车卷筒winch barrel(winch drum ,winding barrel)第7部分油水处理设备，轴系及推进器，造水机Oil Treatment,Oily Water Separator,Shafting &Propeller,Fresh Water Generator分油机oil separator离心分油机oil centrifuge分杂机clarifier分水机purifie造水机fresh water generator真空沸腾式造水机vacuum boiling type fresh-water genetator真空闪发式造水机vacuum flash type fresh-water generator工作水operating water冲洗水flushing water配水盘paring disc活动底盘sliding bowl bottom滑动圈operating slide污渣出口sludge outlet分离筒separator bowl分离筒本体bowl body分离筒盖bowl hood分离筒转轴bowl spindle分离盘bowl discs机盖frame cap阻水环damp ring比重环gravity disc油水分离器oily water separator舱底水bilge锥形盘conical plates粗粒化coalesce放油阀oil drain valve检验旋塞check cock自动空气释放阀automatic air rlease valve除油阀oil rcovery valve (recovered oil valve)液位探测电极liquid level electronic probe除渣阀scum valve自动出油阀automatic oil outlet valve储油柜oil storage tank控制板control panel轴系shafting螺旋桨propeller传动轴transmission shaft中间轴intermeditate shaft (tunnel shaft)推力轴thrust shaft单环推力轴single collar thrust shaft艉轴tail shaft (tube shaft)可调螺距螺旋桨adjustable pitch propeller (variable pitch propeller,controllable pitch propeller)定距桨constant pitch propeller固定桨叶螺旋桨fixed-blade propeller艏部螺旋桨bow propeller横向推理器transverse propeller左（右）螺旋桨left(right)handed propeller推力轴承thrust block推力块thrust pad推力环thrust collar刮油器scraper挡油圈oil deflector油位显示器oil level indicator单环推力轴承（密歇尔推力轴承）Michell thrust bearing(single collar(thrust)bearing)支撑轴承（中间轴轴承)tunnel bearing(intermediate shaft bearing)艉轴管轴承sterntube bearing (stern bearing)铁梨木轴承lignumvitae bearing水润滑轴承water-lubricated bearing白合金轴承white metal bearing桨叶propeller blade空泡cavitation螺旋桨空泡propeller-cavitation压力面空泡pressure-face cavitation(face cavitation)吸力面空泡suction-face cavitation导边空泡leading edge cavitation蒸发器evaporator加热器heater冷凝器condenser挡水器demiser抽气喷射器air ejector凝水泵distillate pump盐水泵brine pump闪发室flash chamber盐度计salinity indicator第8部分交流发电机及配电板Alternating Current Generator& Switchboard交流发电机altemator直流发电机dynamo发电机generator电磁式发电机electro-magnetic generator励磁场线圈magnetic field coil自励self-excited串励serise-wound并励shunt-wound复励compound-wound定子stator转子rotor电刷electric brush灭弧罩arc shield原动机prime motor配电箱distribution board主配电板main switch board区域配电板section board汇流排bus bar配电板load-dispatching board(switch board)频率fequency相位phase同相in phase同步指示器synchroscope自动电压调节器automatic voltage regulator (AVR)自动分载装置automatic load-sharing device自动调频调载器automatic frequency and load regulator发电机屏genertor pnel试验板test board供电网supply network岸电接线箱shore connection box脱扣装置trip device保护装置protection device欠压装置under-voltage protection失压装置no-voltage protection过载保护over-load protection过流保护over-current protection逆功率保护reverse power protection缺相保护open-phase protection短路电流保护short circuit current protection操纵平台control platform开关switch过载开关overload switch双刀开关double pole switch限位开关limit switch断路器breaker断流器cut-out自动断路器automatic circuit breaker过载断路器over load circuit breaker空气断路器air circuit breaker整流器rectifier变压器transformer耦合变压器couple transformer放大器amplifier换向器commutator起动器stater继电器relay电抗器reactor电阻器resisor电容器condenser (capacitor)接触器contactor接线盒connection box并车操作parallel operation电流表ammeter电压表voltmeter功率表wattmeter频率表frequency meter并车开关paralleling switch电动机motor三相电动机three-phase motor同步感应电动机synchronous induction motor 异步电动机asynchronous motor鼠笼式电动机squirrel cage motor第9部分法规及消防设备Watchkeeping,International Convention &Fire FightingSTCW 公约《1978年international convention on standards of training,海员培训，发证和值certification and watchkeeping for seafarers 1978班标准国际公约》值班watchkeeping值班人员watchkeeper (watchkeeping personnel)航行值班underway watch接班人员relief定员rating任职资格qualification值班要求watch requirements对职责的适应fitness for duty职责范围areas of responsibility日常调节routine adjustment逃生路线escape routes驾驶台命令bridge order轮机日志engine room log book无人机舱un-attended machinery space (UMS)(unmanned machinery space)国际公约international convention国际海事组织international maritime organization (IMO)海事委员会maritime commission()MARPOL公约《1973年防止international convention for the prevention of pollution船舶污染国际公约》（1978年修正）from ships 1973 (as modified by the protocol of 1978 relating therto)SOLAS公约《国际海上人命安全公约》international convention for the safety of life at sea油类记录簿oil record book国际防止污染证书(IOPP)international oil pollution prevention certificate原油洗舱(COW) crude oil washing system惰性气体系统(IGS) inert gas system专用压载舱(SBT) segregated ballast tanks清洁压载舱(CBT) clean ballast tanks排油监控系统oil discharge monitoring and control system焚烧炉incinerator散装有害液体货物记录簿cargo record book for ships carrying noxious liquid substances in bulk 国际散装有害液体运输防污证书international pollution prevention certificate for the carriage of noxious liquid substances in bulk客船安全证书passenger ship safety certificate货船无线电安全证书cargo ship safety radio certificate货船结构安全证书cargo ship safety construction certificate货船设备安全证书cargo ship safety equipment certificate中国船级社china classification society(CCS)中华人民共和国船舶检验局the register of shipping of the people's republic of china (ZC)定期检验periodical survey更新检验renewal survey年检annual survey中间检验intermediate survey火警探测器fire detector感烟探测器smoke detector火焰探测器flame detector感温探测器heat detector烟管警报系统smoke pipe fire alarm system 蜂鸣器buzzer警铃alarm bell警报器howler灭火剂extinguishant灭火设备fire fighting equipment固定灭火设备fixed fire fighting equipment 便携式灭火器portable extinguisher碳酸钠与酸混和灭火器soda-acid extinguisher泡沫式灭火器foam extinguisher化学泡沫式灭火器chemical foam extinguisher 机械泡沫式灭火器mechanical foam extinguisher 二氧化碳灭火器carbon-dioxide extinguisher 干粉灭火器dry powder extinguisher插销plunger钢瓶steel container喷嘴nozzle把手handle排出管discharge hose触发开关trigger control喇叭状喷管horn固定灭火装置fixed fire fighting installation 救火泵fire pump应急救火泵emergency fire pump增压泵booster pump消防栓hydrant皮龙管hosepipe(hose)快速扣合接头snap-in connector喷头sprinkler head (sprayer)泡沫发生器foam generator惰性气体发生器insert gas generator消防部署fire fighting strategy消防演习fire fighting drills呼吸面具breathing apparatus卤化烃系统halon system卤化烃1301 halon 1301(BTM)卤化烃1211 halon 1211(BCF)第10 部分维修常用词汇Useful Expressions in Repair ListA. 故障Troubles发现已无法修复found beyond repir发现尺寸过大found over-sized发现反应缓慢found slow function发现不正常found out of order发现不合标准found not up to standard发现不准确found inaccurate发现失效found ineffective发现失去作用found out of function发现咬住found seized发现冻结found stuck fast by icing发现过热found over heated发现过度磨损found excessive wear(found worn out;found worn away) 发现有一点倾斜found a little bit inclined发现因过热而毁坏found destroyed by over heating发现龟裂found chapped发现塌陷found collapaed发现运转失灵found out of operation发现呈椭圆形found oval发现拉痕found scored发现拉毛面积found scuffed about XX in area发现变形found deformed发现变形超过xx mm found deformed over a length of XX MM发现松动found loose发现油污found greasy发现赃污found dirty发现挤铅found squeezed发现弯曲found bent发现故障found faulty发现结霜found frosted发现损坏found damaged发现破裂成片found broken into pieces发现部分剥离found partly detached发现部分阻塞found partly blocked发现剧烈震动found violent vibration发现效率不高found low efficiency发现挠曲found twisted发现烧坏found burnt发现堵塞found choked发现断裂found fractured发现接地found earthed发现敲缸found knocking发现漏泄found leaking(leaky)发现熔化found melted away发现缩减约10mm found reduced about 10 mm发现在气缸内卡住found jammed up in the cylinder在某部位发现裂纹found cracked in way of如必要if necessary如发现必要if found chapped如发现有毛病any defectives if foundB.一般要求General Requirement s一式两份交轮机长to be handed over to C/Ein duplicate(two copies)一式三份交轮机长to be handed over to C/Ein triplicate(three copies)一式四份交轮机长to be handed over to C/E in quadruplicate送交轮机长to be sent to C/E(to be delivered to C/E;TO be submitted to C/E) 厂供to be supplied by yard以备检验to be prepared for survey用波浪键修补to be remedied by means of metallock用船上备件替换to be replaced with ship's spare用千斤顶提起to be jacked up出具证书certificates to be issued出具检验报告survey report to be issued充to be charged充以二氧化碳气体to be filled with co2 gas运至to be transported to取消to be cancelled供应to be provided供验船师检验to be presented for surveyor's inspection所有钢瓶测试all bottles to be calibrated所有钢瓶称重all bottles to be weighted制造并供应to be made and supplied按现有的制作并安装to be fabricated and installed according to the existing one除霜to be defrosted砌to be paved重充氟里昂12 to be refilled with freon 12重充水银ti be recharged with marcury送至to be removed to(to be sent to;to be transferred to )送车间修理to be sent to work shop for repaira退回船上作备用to be returned to ship as spare绘制图纸交船srawing to be made and sumitted to ship按要求修理to be repaired as required按302项处理treated as item 302换新to be renewed消除eliminated。

1、主机Main Engine (M.E.)2、主机遥控M.E. remote control3、螺旋桨propeller4、可调螺旋桨CPP (Controllable pitch propeller)5、齿轮箱gearbox6、轴承bearing7、推力（中间）轴承thrust (intermediate) bearing8、凸轮轴camshaft9、活塞piston10、主起动阀main starting valve11、调速器governor12、气缸cylinder13、高压油泵high-pressure oil pump14、调油杆oil-adjusting lever15、油排齿条格数tooth sector16、起动（停止）电磁阀starting (stopping) electric-magnetic valve17、盘车机turning gear18、扫气空气scanvage air19、泵（马达）pump(motor)20、鼓风机blower21、转速rpm22、流量flow23、手动manual24、自动automatic25、应急emergency26、限制limit27、指示indicate28、故障abnormal/trouble29、工况（负荷）working condition (load)30、确认（应答）confirm (response)31、平稳steady (smooth)32、调节adjust33、复位reset34、自检self-check35、备用stand-by36、啮合gear37、脱开detach38、减速slow-down39、失败failure40、零位nil position41、反馈信号feed signal42、转换信号change-over signal44、换向信号reverse signal45、接通connect46、断开cut-off47、切断cut48、正常normal49、无异常现象no abnormal50、闭锁lock51、试验test & trial52、电源power supply (source)53、交流电源AC 220V SOURCE54、直流电源DC 24V SOURCE1、主机推进系统M/E propulsion system2、主机遥控装置M/E remote control unit3、机旁local (by engine side)4、集控室ECR (centralized control room)5、驾驶室W/H (wheel-house)5、桥楼bridge6、遥控主车钟remote control main telegraph7、微速dead slow8、半速half8、全速full9、完车finish10、辅车钟aux. telegraph11、应急车钟emergency telegraph12、车钟记录仪telegraph recorder13、设定速度rated speed14、定速constant speed15、模拟试验simulation test16、测速装置speed-measuring unit17、转速传感器rpm sensor18、起动空气压力表starting air pressure gauge1、程序（换向/起动/慢转起动/转速/转速自动）控制program (change-over / starting / slow starting / rpm / rpm automatic) control2、三次自动重复起动automatic restarting for three times3、重起动restart4、错向报警wrong-way alarm5、临界转速（最小转速/最大倒车转速/热负荷/手动转速/燃油/扫气压力/手动燃油）限制critical rpm (Min. rpm / Max. astern rpm / hot load / manual rpm / F.O. / scanvage pressure / manual F.O.) limit6、应急操纵（运行）emergency maneuvering (running)7、应急（自动）停车emergency（automatic）stop8、安全保护装置safety protection unit9、盘车机未脱开Turning gear is still geared10、滑油压力低The pressure of L.O. is too low.11、气缸（活塞）冷却水压力低The pressure of cooling water for cylinder (piston) is too low.12、超速overspeed13、活塞冷却水流量低The flow cooling water for piston is too low.14、扫气空气（推力轴承）温度高The temperature of scanvage air (thrust bearing) is too high.15、起动时间过长The starting time is too long.16、三次起动失败starting failure for a third time17、起动（控制）空气压力低The pressure of starting（control）air is too low.18、主起动阀未打开The main starting valve isn’t opened.19、机旁操纵（调油）手柄位置The local handle position for maneuvering.20、系统故障system failure21、内部电源故障inside power source failure22、故障显示failure display23、气缸油断流cylinder oil non-flow24、越空skip25、油雾探油装置oil mist detector26、鼓风机接通（断开）The blower is powered (out down).27、调速器governor28、报警器消音按钮The silencer push button for alarm unit.29、试灯按钮push button for lighting30、凸轮轴位置检测器detector for camshaft position31、电气转换I/P32、故障指示灯failure indicator33、调光器旋钮snob for light regulator34、执行机构actuator35、燃油刻度指示表fuel oil dial indicator电站自动化Automation of power StationⅠ.1、柴油发电机起动失败D/G start failure.2、柴油发电机超速停车D/G overspeed stop.3、柴油发电机滑油低压停车D/G Lub. oil low press. stop.4、柴油发电机淡水高温停车D/G F.W. high temp. stop.5、柴油发电机起动空气低压D/G starting air low press.6、柴油发电机停车电磁阀故障D/G auto-stop magnetic valve failure.7、柴油发电机测速装置故障D/G speed measurement failure.8、柴油发电机空气低压D/G control air low press.9、柴油发电机电源故障D/G power source failure.10、柴油发电机增压器滑油低压D/G turbocharger Lub. Oil low press.11、柴油发电机燃油泄漏柜液位高D/G F.O. drain tank high level12、柴油发电机预滑油故障D/G L.O. preheatment failure.13、柴油发电机报警闭锁D/G alarm lock.14、柴油发电机功率管理故障D/G power control failure.15、柴油发电机公共报警D/G common alarm.16、柴油发电机燃油模块故障D/G F.O. module failure.17、柴油发电机测速传感器D/G speed sensor.18、柴油发电机预供油泵马达D/G presupply oil pump motor.19、主配电板调速马达Main switchboard speed-governing motor.20、遥控和自动起动（控制）Remote control and auto start (control)21、就地控制local control22、遥控（手动）停车stop by remote (hand) control23、发电机运行D/G operation24、发电机温度及压力显示Temperature & pressure display of D/G25、发电机燃油进口压力D/G F.O. inlet press.26、发电机高温淡水（滑油）进口压力D/G high-temp. F.W. (Lub.Oil.) intlet press.27、发电机燃油（滑油）进口温度D/G F.O. (L.O.) inlet temp.28、发电机高温淡水出口温度D/G high-temp. F.W. outlet temp.29、发电机1－3缸排气温度Exhaust temp. from the first to the third cylinder.30、发电机R相（S相、TS相）绕组温度D/G R (S、TS)-phase coil temp.31、主空气断路器main air breaker32、电压表（电流表、功率表、同步表、功率因素表、频率表）Voltmeter (Ammeter / powermeter / synchronoscope / power factor meter / frequency meter)33、转换开关change-over switch34、发电机加热器开关D/G heater switch35、调频转换开关frequency-regulating switch36、充磁（消音/复位）按钮magnetic push button (silencer / reset)37、岸电供电（同步）指示灯shore electricity-supply (synchronous) indicator38、绝缘监视仪insulation monitor39、熔断器fuseⅡ.（主机主要部件）Main Parts for M/E1、engine frame 机架2、cylinder 气缸3、piston 活塞4、crosshead 十字头5、bedplate 机座6、crankshaft 曲轴7、cylinder cover/head 气缸盖8、connecting rod 连杆9、turbocharger 增压器10、driving chain 传动链11、air cooler 空气冷却器12、scanvage box 扫气箱13、oil sprayer 喷油器14、oil nozzle 喷油嘴15、exhaust valve 排气阀16、sealing ring密封环17、cylinder liner 气缸套18、piston rod 活塞杆Ⅲ.机舱布置图Engine room arrangement1、main engine /M.E.主机2、intermediate shaft中间轴3、bearing轴承4、propeller shaft螺旋桨轴5、stern tube艉管6、aft seal head tank 后密封油箱7、FWD seal head tank前密封油箱8、stern tube L.O. drain tank 艉管滑油泄放柜9、chemical cleaning tank 化学清洗柜10、L.O. drain tank11、sludge oil trap 油渣收集柜12、rust preventer tank 防锈剂柜13、oily water separator油水分离器14、Low sea chest 低位海水门15、L.O. transfer pump16、bilge pump 舱底泵17、M/E lub oil pump18、M/E S.W. cooling pump 主机海水泵19、sludge pump 油渣泵20、ejector pump for F.W.G 造水装置工作水泵21、stern tube L.O. pump 艉轴管滑油泵22、H.F.O. Transfer pump 燃油输送泵23、ballast pump压载泵24、bilge & G.S. pump 舱底总用泵25、Fire & G.S. pump 消防总用泵26、Provision Ref. Unit S.W. pump伙食冷藏海水泵27、aux. S.W. Cooling pump 辅海水泵28、L.O. purify cleaning tray 滑油分油机洗池。

轮机专业英语词汇Lesson 1 accommodation房间，居住区arbitrary 任意的，武断的，独裁的bulkhead 船舱壁，船舱的隔墙cruise 巡游，巡航destroyer 驱逐舰distinct 清楚的，明显的，独特的dredger 挖泥船，挖泥机endure度过，忍受evaporator 造水机frigate 护卫舰funnel 烟囱habitability 可居住性hatch 舱口layout 规划，设计，布局longitudinal 经度的，纵向的metric 米制的，公制的stabilizer减摇鳍transverse 横向的，横断的trawler [渔]拖捞船tug 拖船cutter suction dredger 绞吸式挖泥船elevation drawing 正面图naval architect 造船工程师oily water separator 油水分离器prime mover 原动机self--sustaining 自维持trailing hopper suction dredger 耙吸式挖泥船twin--screw drive 双桨推进Lesson 2accomplish 完成adjacent 临近的advantage 优势，优点，长处alternator 交流发电机application 请求，应用，运用，施用aspirate吸入，吸出atomized雾化的attain 达到，到达auxiliary 辅助的balance 平衡，抵消blow 吹，鼓风burn燃烧cause引起，原因centripetal 向心的chamber 腔，室charge装，充，充填物clockwise 顺时针方向closure 关闭combine 组合，联合combustion 燃烧compress 压缩consist (of) 由…组成continue 继续进行contrive 设计，设法crank 曲柄crankshaft 曲轴cycle 循环cylinder 气缸Descend 下降，下行diesel 柴油，柴油机draw 抽吸encourage 促使entrain 进入event 事件，过程exhaust 排出，耗尽，排气，废气expel 排出，驱逐explain 解释，说明fine 细小的，好的fix 固定force迫使fresh 新鲜的，淡水的generator发电机generous 丰富的，充分的ignite 点燃imply暗示induce引起，招致inefficient 效率低的，无效的inertia 惯性inhale 吸入inject 喷射injector喷射器，喷油器inlet 进口，入口internal 内部的majority 多数，大多数marine 海运的，船用的maximize 把……增加到最大量medium中间的，介质mixing 混合naturally 自然的operation工作，操作，运转，进程overlap﹙与…﹚交叠，重叠，搭接piston 活塞poppet 提升positive正的preserve 保留prevent 妨碍，阻止Principle 原则，原理proceed 进行promote促进，加速，引起propeller 螺旋桨，推进器propulsion推进﹙装置﹚remain剩下，残存residual剩下的，残余的retard 推迟，延迟revolution 转rotate旋转，回转scavenge扫除，吹除separate 分离，分开sequence顺序，系列sound声音spray 喷雾，﹙水，油﹚雾stroke 冲程，行程theoretically 理论上地Throughflow 进流量，贯穿气流timing定时turbocharge 涡轮增压turbocharger涡轮增压器typical 典型的value 价值，数值vast 大量的，巨大的via 经由，通过Blow down 排出，下降bottom dead centre 下止点in turn 依次，轮流变成loop scavenge 回流扫气on board ship 在船上r/min 转／分钟reduction gear box减速齿轮箱slight ram 进气阀座top dead centre 上止点turn into 变成uniflow scavenge 直流扫气unexpelled 未排出的Lesson 3 adequate 足够的，充分的adjustment 调整，调节admit允许进入，导入advanced 高级的，先进的annular 环形的appropriate 适当的approx 大约assembly 组件，组装bearing 轴承bedplate 机座benefit 利益，好处，有益于，有助于，收益block块，体bore螺栓，用螺栓固定bolt 缸孔，钻孔，镗孔camshaft凸轮轴cap盖，帽casing 箱，外壳caulk敛缝，嵌塞channel 通道chock 侧块，锲型块chromium镀铬clearance 间隙cock 旋塞component 部件conical锥形的construction 结构crankpin曲柄销cross十字的，交叉的，交叉，横过current 当前的，流行的，电流，水流，气流diagonal 对角的，斜的diameter 直径displace 错位，变位distributor分配器double 双层的dowel销钉drill 钻孔duct管道edg边缘efficient 高效的，有效率的，能干的electronic电子的emission散发，发射，喷射，烟雾排放enclose 包围，封闭ensure 保证，担保environmental周围的，环境的expose 暴露，露出extend延长，伸长film油膜flange 法兰，翻边flat 平的foremost 最前的forge锻造frame机架groove 槽，沟guide导板，导向器，导向，引导height 高度horizontally 水平的indicator示功器insert 插入integral 整体的jacket 夹层，水套joint接合，接头journal 轴颈liner﹙气缸﹚衬套locate 位于，查出，找出，置于某位longitudinal 纵向的maneuverability机动操作性，机动性mount安装narrow 狭窄的opening开口opposite 在…对面，与…相对optimal 最理想的，最佳的period 期间pin 销子precise精确的，准确的，精确recess 凹槽，凹座，凹入处reliability可靠性requiremment 需求，要求rest 放置，坐落rotary 旋转的round圆的，使成圆形scraper 刮油器，刮子screw螺钉，用螺钉固定，拧入seating座，底座section段，表面secure固定shim 垫片shoe滑靴，滑块shrink 红套slightly轻微的slot槽，缝，开槽specification 详述，规格，说明书，规范stud双头螺栓surface 表面technology工艺，科技，技术chickness厚度thrust推，推力topmost 最上部transverse横向的turn 车削，转动variable变量，可变的vertical垂直的vital生命的，至关重要的weld 焊接built in 内装的，机内的，固定的carrier ring承磨环cast iron铸铁chain transmission链条传动﹙机构﹚fitted bolt拂配螺栓heat resistant耐热的machine turned车削的，车制的MEP 平均有效压力SFOC 比耗油率tap bolt 椎体螺栓telescopic pipe伸缩管，拉管well—proven充分证明的white metal 白合金Lesson 4 catalyst催化剂catalytic催化剂的cavitation 气穴现象centrifuge分油机component﹙组合﹚成分，元件，构件consumption 消费，消费量contaminant 杂质contaminate 污染conventional惯例的，常规的，传统的deaerate除气，除氧delivery 传递，输送deterioration变坏，退化，变质flexibility 灵活性，变通性impurity 杂质混杂物，夹杂物incorporate合并的，组合，混合，一体化irrespective不顾的，不考虑的occasionally 有时候，偶尔overflow溢流overhaul 大修particularly 独特的，显著的pressurize增压，密封，使…加压provided 倘若purifier/clarifier 分水机\ 分杂机recommendation推荐，建议refinery炼油厂rust 铁锈，﹙使﹚生锈safeguard 维护，保护，保护装置，保护措施traditional传统的，惯例的black—out全船停电booster pump增压泵catalytic fine 催化粉末gasway气道in parallel并联in series串联in view of 考虑到，由于residual fuel渣油spring—loaded弹簧回复的with regard to关于Lesson 5 accommodate收容，装有additional另外的，附加的，额外的alternatively 可供选择的办法auxiliary辅助的，备用的，副的chest 箱，柜deaeration除气inhibit约束，限制于系统内integrate 使成整体，使一体化，结合malfunction故障，失灵，不正常工作scoop 收集器，吸入口standstill 停车thermostatic恒温的by—pass旁通管，旁路，并联的，旁路的expansion tank 膨胀﹙水﹚柜，膨胀水箱in accordance with与…一致，按照Lesson 6attempt 试图，企图automatic 自动的，自动机械burst 突然破裂，爆发，冲破careful谨慎的，小心的compressor 压缩机deposit 沉淀，沉积物direct指导，指挥，直接的，直接地disc 盘drainage排放，排泄，排出物drop下跌，下落，下降effect 实现，达到目的，作用，影响，效果engage 啮合，从事explosion 爆炸facility设备feature功能，部件Fusible易熔的，可熔的guard 防护装置，防护，防卫humidity湿气，湿度immediate 立即的interlock连锁isolate隔缘，绝缘lever杆，杠杆，控制杆，抬起manoeuvring操纵的，机动的melt熔化，融化moisture潮湿，湿气，水汽，湿度，水分occurrence发生，事物pilot 引水员，引导的，控制的，先导的pipeline 管路，管系plug堵，塞，塞子，插头，插销possibility可能性，可能发生的事情Prevent 防止，预防properly适当的ready准备好的，有准备的redundant 备用的reservoir容器﹙空气瓶﹚，蓄压器slight 轻微的，微小的，弱的stringent严厉的，严格的suck 吸，吸取trap挡板，收集器bursting cap 防爆帽by means of 利用，用…方法Lesson 7alkalinity碱度，碱性assist 帮助，协助carbonaceous炭的，含炭的centrifuge离心分离机cleaner清洁剂，清油器cleanse清洗，纯净commercially商业上considerable相当的，大量的counteract 客服detergency去垢能力deterioration变质，恶化detritus碎石，磨屑duplicate双倍的，副本，备品，使加倍exception 例外expose 暴露feature是…特色起重要作用，特性，特点filter过滤，滤器formation形成，构成formulate配制friction摩擦力，摩擦gauge测量，仪表，量规impart耳轴，销轴impinge 给予﹙尤指抽象事物﹚Injector注射器，注油塞interfere影响，干扰involve涉及lacquer用漆涂于…，胶膜，漆lubricator注油器Property 财产，性质，特性quill 注油针replenish补充，补偿residual剩余的，残留的，残渣，残液reversal 反向，变换Rupture破裂store物料﹙间﹚，贮存successful 成功的，良好的undesirable不需要的gudgeon pin 轴销，十字头销，活塞销lubricatingstud 注油塞read out 读数telescope pipe伸缩套管，拉管Lesson 8adequate适当的，充分的adjacent临近的arrangement布置，安排atmosphere 大气，大气的blow鼓风，冲洗blower鼓风机，增压器compressor 压缩机density 密度，浓度differential微分，压差，差别的，微分的electrically电力地，电动地escape 出口，逃逸，溢出essential本质，要点，基本的，重要的pressurize增压，加压process 处理，过程removal排除，移动supercharge增压swirl 漩涡，涡状形，打漩，使…漩涡运动turbine涡轮，涡轮机Lesson 10boss 螺旋桨轴榖cascade倾泻，倾注cone 螺旋桨轴帽，锥形物，使成锥形counteract 抵消，中和，阻碍employ用，使用extend扩充，延伸，伸展helicoidal螺旋面hub桨榖integral 完整的，整体的intermediate中间的，温和的﹙天气﹚outboard外侧的，向舷外的pad垫，衬垫，便笺簿，加上衬垫pitch螺距pivot枢轴，支点，枢轴的，在枢轴上转动，装枢轴于propeller螺旋桨rigid刚性的，刚硬的taper逐渐变细，逐渐减少thrust推力，用力推，冲，插入，挤进tilt ﹙使﹚倾斜，﹙使﹚翘起transfer传递，转移transmission传动，传送cater for供应伙食，迎合face seal 面密封ingot steel钢锭journal bush 轴颈衬套lignum citae铁犁木shuttle tanker穿梭油船stuffing box填料函tailshaft艉轴thrust block 推力块thrust collar推力环Lesson 13 attemperator保温装置，保温器casing 包装，保护性外套convection传送，对流diesel柴油机downcomer下水管，下导管furnace炉子，熔炉，鼓风炉gasstight不漏气的，耐气构造的mounting设备propulsion推进，推进力spherical 球形的，球面的tangent接触的，切线的，相切的variation 变化，变动，变异vertical 垂直的，竖直的combustion chamber燃烧室draw off 撤退，排除﹙水﹚refractory lining 耐火炉衬，耐火﹙材料﹚衬里saturated steam 饱和水蒸气steam generation蒸发，汽化lesson 14bilge舱底bulge不规则突起，鼓起之处condensate冷凝物detritus碎石dislodge 驱逐fracture破裂friable 易碎的，脆的gauge 量，测量，标准尺ignite引燃，着火impurity不纯，杂质，混杂物periodically 周期性地，定时性地precaution预防，警惕preferential 优先的，特惠的rupture破裂，裂开salinity 盐分，盐度scavenge 打扫，从废气中提取sludge淤泥，矿泥，煤泥engine cylinder 发动机气缸non–return 止回pressure gauge 压力计residual heat剩余热sample connection取样口soot blower吹灰器steam trap 疏水器，汽水分离器，凝气阀turbine–generator涡轮发电机lesson 15axial 轴的，轴向的centrifugal离心的configuration构造，结构de–aerate 使除去空气，从﹙液体﹚中除去气泡elliptical椭圆的，省略的equilibrium 平衡，均衡，相称，匀称，平静erratically 不规律的，不定的hydraulic水力的，水压的overhaul 检查piston活塞reciprocate互给，互换，酬答reservoir 水库，水柜axial flow 轴流relief valve安全阀lesson 16 aluminium铝，铝的ammonia 氨，氨水azeotropic共沸的，恒沸点的corrosive腐蚀的，蚀坏的crankcase 曲轴箱elastomer 弹性体，人造橡胶flammable 易燃的，可燃性的fluorinate使与氟素化合glycol 乙二醇hazardous 危险地，冒险的liquefy﹙使﹚溶解，﹙使﹚液化ozonosphere臭氧层shaft 轴，杆状物solenoid螺线管suction 吸入，抽气toxit有毒的，中毒的ventilation 通风methyl–chloride氯甲烷calcium chloride brine氯化钙卤水lesson 18 renewal 更新，恢复thermostat 温度调节装置pneumatic 空气的，气动的alleyway小巷，﹙船上的﹚通道porthold舷窗filter 过滤，过滤器，滤波器damper起抑制作用的因素，节气阀stuffiness 不通风，闷热odor 气味，名声louver天窗，屋顶窗lesson 23cavity 洞，空穴，腔conjunction联合，关联，连接词hydraulic 水力的，水压的incorporate合并的，一体化的，合并multiple多样的，多重的，倍数offset偏移量，偏移orifice孔，口swashplate旋转斜盘torqueses 颈部四周的彩色项毛圈lbf∕in²压强单位﹙in²为平方英寸﹚pressure control valves压力控制阀sequence valves次序阀slow speed high torque motor 低速高扭矩电动机lesson 24derrick起重机grease油脂，涂抹油handling处理，操作的hydraulic水力的，水压的inspection检查，视察luffing 转舵luff 俯仰运动，上下摆动，起动机臂的转动winch 绞盘deck cranes 甲板起重机lesson 25anchor 锚bollard系缆桩capstan 绞缆机clutch 离合器grip 夹住，夹具发卡handle 处理hatch 舱口haul 拖，绞moor 系泊，系缆render绞，拖snug凸起，突齿split分离的substantial坚实ension 张力wrap卷，包，使弯曲windlass 锚机worm蜗杆cable lifter 锚链轮let go 放出pay out 放出，放开，松开﹙绳索﹚spurling \pipe 锚链筒lesson 26 activate 使活动changeover 转换consequently从而，因此exclusive唯一的identical 完全相同的lam撞杆linkage 连接mechanism 机械装置necessitate成为必要，需要response 反应rotary旋转的spindle 轴，杆switch开关，电闸，转换telemotor液压传动操舵装置audible and visual alarms 声光报警floating lever 浮动杆rudder stock 舵柱rotary vane tpye转页式steering gear操舵装置steering gear compartment 舵机房variable delivery pump变量泵lesson 28 amplifier扩音器，放大器inductive诱导的，感应的installation安装，装置magnetic磁的，有磁性的navigation航海，航空preliminary 预备的，初步的rectifier校正器，矫正器，整流器rotation旋转segment段，节，片段，分割switchboard配电盘，接线总机alternating current 交流电lesson 28 alternator交流发电机dial刻度盘，钟面，转盘frequency频率instrumentation 使用仪器negligible可以忽略的，不予重视的synchroscope同步检定器voltmeters伏特表，电压表overspeed governor 限速器reverse power protection逆功率保护lesson 29 adjacent相邻的amplifier放大器armature电枢brighten﹙使﹚变亮brushless 无﹙电﹚刷的capacitive电容性的clockwise顺时针方向的，顺时针方向地commutator整流子，换向器compounded 负激励的counter计数器，相反的，抵消darken﹙使﹚变暗electromagnet电磁铁exciter励磁机feature部件，特性fluctuation波动hunting 振荡inductive ﹙电﹚感性的instrumentation仪器lagging 绝缘层材料，滞后leading超前pointer指针polarity极性pole棒，柱，杆，极，磁极，电极product 产品，产物，乘机series串联，系列shunt并激statically 静止的synchdroscope同步指示器trip 脱扣机构voltage电压，伏特数winding绕组a.c.distribution system交流电分配系统brushgear电刷机构d.c.distribution system直流电分配系统delta formation 三角形接法earthed neutral 接地点excitation励磁field coil 励磁线圈，磁场线圈incoming machine待并机indicating lamps 指示灯miniature circuit breakers 微型断路器navigation lights 航行灯overcorrecting过调parallel operation并车操作power factor功率因数prime mover原动机reverse power protection 逆功率保护slip–ring滑环start formation星形连法Leeson 30commutator换向器，转接器straightforward简单的，易懂的，直截了当的，坦率的interpole 极间极，附加极，辅助整流极，换向极momentary 瞬间的，刹那间的multiplicity多样性outgoing 引出的，外行的feeder 馈线，馈电板panel仪表盘，控制面板dead死的，不带电的live活的，带电的permissible容许的，许可的breaker 断路器rear背面﹙的﹚，后面﹙的﹚isolator 绝缘子，隔离开关ammeter安培表，电流表voltmeter 伏特计，电压表additional额外的，附加的frequency频率transformer 变换器，变压器synchroscope 同步指示器wattmeter瓦特计，功率表corresponding相应的，相当的extremely极端的rare罕见的alive 带电的alternating current 交流电bus bar 汇流排dead front type 前端不带电式differ from 不同于，区别于direct current 直流电distribution board分电板，分电箱field circuit 磁场电路shunt wound motor并励电动机splitting up分解，分裂sub board 分区﹙区域﹚配电板tripping device跳闸开关﹙装置﹚。

1.Lesson12.internal combustion engine 内燃机3.marine diesel engine 船用柴油机4.naturally aspirated 自然吸气5.two - stroke cycle 二冲程循环6.auxiliary generator engine 辅助发电柴油机7.centrifugal turbocharger 离心式涡轮增压器8.exhaust valve 排气阀9.top dead centre 上止点10.bottom dead centre 下止点11.loop scavenge 回流扫气12.uniflow scavenge 直流扫气13.the period of valve overlap 气阀重叠期14.fuel injector 喷油器bustion chamber 燃烧室16.power stroke 做功冲程Lesson21.side - chock bolt 侧楔螺栓2.end - chock bolt 端楔螺栓3.cross girder 横梁4.main bearing 主轴承5.thrust block 推力轴承6.scavenging air box 扫气箱7.chain transmission 链传动8.cylinder block 气缸体9.tie rod 贯穿螺栓10.scavenging air port 扫气口11.cylinder cover 气缸盖12.cylinder liner 气缸套13.indicator cock 示功考克14.dowel pin 定位销15.piston skirt 活塞裙16.piston crown 活塞头17.running - in period 磨合期18.thermal stress 热应力19.crosshead shoe 十字头滑块20.tap- bolt 锥形螺栓21.stuffing box 填料函22.connecting rod 连杆23.force - feed lubrication system 强力润滑系统24.bearing clearance 轴承间隙25.crank journal 曲柄轴颈Lesson31.cetane number 十六烷值2.calorific value 热值3.carbon residue 残炭4.specific gravity 比重5.sulphur content 硫分6.ash content 灰分7.ignition delay 滞燃期8.catalytic fine 催化粉末9.settling tank 沉淀柜1/ 910.service tank 日用柜11.booster pump 增压泵12.viscosity regulator 粘度调节器13.quick closing valve 速闭阀14.needle valve 针阀15.flyweight type governor 飞重式调速器Lesson41.trouble free life 无故障使用寿命2.lubricating oil film 润滑油膜3.carbonaceous deposit 积碳4.wear detritus 磨屑5.ring land 活塞环岸6.ring groove 环槽7.friction loss 摩擦损失8.detergency property 去垢能力9.feed ratel 供油率10.sulphuric acid 硫酸11.drain tank 循环油柜12.level gauge 液位表13.gudgeon pin 活塞销14.crosshead bearing 十字头轴承15.gas seal 气封Lesson51.heat engine 热机2.cylinder jacket 气缸水套3.pressure relief valve 溢流阀4.fresh water cooler 淡水冷却器5.distilled water 蒸馏水6.corrosion inhibitor 缓蚀剂7.chemical additive 化学添加剂8.galvanized piping 镀锌管9.expansion tank 膨胀水箱10.air lock 气塞11.auxiliary engine 副机12.central cooling system 中央冷却系统13.fresh water generator 造水机14.three - way valve 三通阀15.blind －flange 盲板Lesson 6pressed air 压缩空气2.air reservoir 空气瓶3.non - return valve 止回阀或单向阀4.cylinder air start valve 气缸启动阀5.pilot air 控制空气6.pilot air control valve 起动控制阀7.air distributor 空气分配器8.air start lever 起动手柄9.turning gear 盘车机10.air start manifold 起动空气总管11.air compressor 空压机12.flame trap 阻焰器13.relief valve 安全阀2/ 914.bursting caps or discs 防爆帽或防爆盘15.fusible plug 易熔塞Lesson71.reversing gearbox 换向齿轮箱2.controllable - pitch propeller 调距桨3.instruction book 说明书4.indicator cock 示功考克5.auxiliary scavenge blower 辅助鼓风机6.direction handle 换向手柄7.telegraph reply lever 车钟应答手柄8.manoeuvring handle 操纵手柄9.regular maintenance work 定期维修工作10.instruction manual 安装手册11.indicator card 示功图12.fuel valve 燃油阀13.carbon deposit 积炭14.connecting rod top and bottom ends 连杆大小端15.lubricating oil sump 滑油机箱Lesson81.motor vessel 内燃机船2.SCR ( Selective Catalytic NO Reduction system) 选择性催化还原系统3.VIT 可调喷油定时4.add - on device 附加设备5.fuel injection timing 喷油定时6.fuel injection rate 喷油率7.cylinder lube oil feed 气缸滑油供油率8.Alpha Lubricator 阿尔法气缸注油器9.mechanical lubricator 机械注油器10.times between overhauls 大修间隔时间11.diagnostic system 诊断系统12.fuel injection pump 喷油泵13.exhaust valve actuator 排气阀操作机构14.starting air distributor 起动空气分配器15.local control stand 机旁控制台16.Hydraulic Power Supply ( HPS ) 液压动力源17.Hydraulic Cylinder Units ( HCU ) 液压控制单元18.Engine Control System ( ECS) 发动机控制系统19.crankshaft position sensing system 曲轴位置传感系统20.Local Operating Panel ( LOP ) 机旁控制面板21.self cleaning filter 自清滤器22.axial piston pump 轴向柱塞泵23.engine driven pump 机带泵24.hydraulic pump 液压泵25.second - order moment compensator 二阶力矩补偿器26.integrated control system 综合控制系统27.double - walled piping 双壁管28.ELFI 比例电子喷射控制阀29.ELV A 电子排气阀操作器30.pressure accumulator 蓄压器Lesson91.auxiliary machinery 辅助机械3/ 92.fire - tube boiler 火管锅炉3.donkey boiler 辅锅炉4.water-tube boiler 水管锅炉5.steam drum 汽包6.generating tube 蒸发管7.heat transfer surface 传热面8.down comer 下降管9.water drum 水筒10.superheated steam 过热蒸汽11.exhaust gas boiler 废气锅炉12.boiler mounting 锅炉附件13.main stop valve 主停汽阀14.feed check valve 给水止回阀15.water level indicator 水位计16.blow - down valve 下排污阀17.scum valve 浮渣阀18.salinometer valve 盐度计阀19.chemical dosing valve 投药阀20.smoke indicator 烟气指示器21.primary swirler 主配风器22.air register 调风门23.wire bristle brush 钢丝刷24.waste heat recovery plant 废热回收装置25.water carry - over 蒸汽携水26.forced draught air pressure 强力风压27.soot blower 吹灰器28.air / fuel ratio 风油比29.high salinity alarm 高盐度报警30.condensate system 凝水系统Lesson101.displacement pump 容积式泵2.centrifugal pump 离心泵3.reciprocating pump 往复泵4.rotary pump 回转泵5.gear pump 齿轮泵6.volute pump 蜗壳式泵7.diffuser pump 导轮式泵8.mixed - flow pump 混流泵9.axial pump 轴流泵10.regenerative pump 旋涡泵11.relief valve 安全阀12.suction lift 吸高13.centrifugal force 离心力14.bearing bush 轴瓦15.sealing arrangement 密封装置16.packed gland 填料压盖17.mechanical seal 机械密封18.priming unit 引水装置19.wear ring 承磨环20.atmospheric pressure 大气压力21.suction valve 吸入阀22.discharge valve 排出阀4/ 923.self - priming 自吸24.saturation temperature 饱和温度25.vapor bubble 气泡26.Available Net Positive Suction Head 有效汽蚀余量27.wear and tear 磨损28.volumetric efficiency 容积效率29.shaft seal 轴封30.the eye of the impeller 叶轮中心Lesson111.marine refrigeration 船舶制冷2.air conditioning 空调3.vapour compression cycle 蒸汽压缩循环4.expansion valve 膨胀阀5.evaporator coil 蒸发盘管tent heat 潜热7.throttling effect 节流作用8.cooling medium 冷却介质9.secondary refrigerant 载冷剂10.critical temperature 临界温度11.carbon dioxide 二氧化碳12.sub - cooling 过冷13.calcium chloride brine 氯化钙盐水14.charging valve 充剂阀15.CFC 不含氢的氯氟烃16.HCFC 含氢的氯氟烃17.purge valve 驱气阀18.liquid line sight glass 液管视液镜19.leak detector lamp 检漏灯20.high pressure cut - out 高压控制器21.low pressure cut - out 低压控制器22.oil failure cut - out 油压差控制器23.liquid - hammering 液击24.oil - hammering 油击25.under - charge 冲击不足Lesson121.dry bulb temperature 干球温度2.wet bulb temperature 湿球温度3.relative humidity 相对湿度4.dew point 露点5.air conditioning system 空调系统6.refrigeration plant 制冷装置7.single - duct system 单风管系统8.twin - duct system 双风管系统9.“ single - duct with reheat ” system 单风管再热系统10.natural ventilation 自然通风11.mechanical ventilation 机械通风12.intermediate weather condition 中间气候条件13.by trial and error 用试凑法14.insulation vapour seal 隔热气封15.plastic film 塑料膜Lesson131.oily water separator 油水分离器5/ 92.Crude Oil Washing 原油洗舱3.bunker tank 燃料舱4.load on top 置于上部法5.slop tank 污油柜6.Segregated Ballast Tank ( SBT ) 隔离压载舱7.Clean Ballast Tank ( CBT ) 清洁压载舱8.coarse separating compartment 粗分离室9.International Oil Pollution Prevention ( IOPP ) certificates 国际防油污染证书10.oil - free water 无油的水11.oil collection spacel 集油室12.catch plate 捕集板13.steam or electric heating coils 蒸汽或电加热盘管14.de - oiling 去油15.surface tension 表面张力Lesson141.territorial waters 领海2.sewage treatment plant 生活污水处理装置3.extended aeration process 充分曝气过程4.inert sludge 惰性淤泥5.Bio - chemical Oxygen Demand ( BOD ) 生化需氧量6.aerobic bacteria 好氧菌7.anaerobic bacteria 厌氧菌8.suspended solids 悬浮固体9.coliform count 大肠杆菌数10.hydrogen sulphide 硫化氢11.sullage tank 污水柜12.chemical dosage rate 加药率13.watertight compartment 水密舱14.aeration compartment 曝气室15.activated sludge 活性污泥Lesson151.centrifugal separation 离心分离2.batch operation 间歇运行3.cylindrical interface 圆柱形分界面4.dam ring or gravity disc 比重环5.bowl periphery 分离筒边缘6.centrifugal force 离心力7.back pressure 背压8.ejection process 排渣过程9.flushing water 冲洗水10.operating water 工作水11.heavy fuel oil 重油12.water transducer 水分传感器13.special tool 专用工具14.catalytic fine 催化粉末15.left - hand thread 左旋螺纹Lesson161.air compressor 空压机2.spring - loaded 弹簧加载3.non - return delivery valve 排出止回阀4.first - stage cooler 第一级冷却器6/ 95.centrifugal compressor 离心式压缩机6.axial compressor 轴向压缩机7.unloaded running 卸载运行8.automatic drain 自动放残9.buffer plate 缓冲片10.valve plate 阀片11.spring plate 弹簧片12.split pin 开口销13.castle nut 开槽螺母14.nut washer 螺母垫圈15.lift washer 升程垫圈16.damper plate 阻尼片17.valve seat 阀座18.foreign matter 杂质19.shaft seal 轴封20.stationary part 静止部件Lesson171.fresh water generator 造水机2.distillation process 蒸馏过程3.shell - and - tube type 壳管式4.plate type 板式5.vacuum distillation 真空蒸馏6.periodically unmanned engine room 定期无人机舱7.heating medium 加热介质8.titanium plate heat exchanger 钛板热交换器9.two - stage brine / air ejector 两级排盐/真空泵10.ejector pump 喷射器供水泵（海水泵）11.built - in fresh water pump 内置凝水泵12.feed water anti - scale chemical dosing unit 给水防结垢药剂添加装置13.evaporating temperature 蒸发温度14.solenoid valve 电磁阀15.dump valve 泄放阀Lesson181.hydraulic system 液压系统2.hydraulic motor 液压马达3.marine engineering 轮机工程4.linear motion 直线运动5.hydraulic energy 液压能6.swashplate type 倾斜盘7.prime mover 原动机8.kidney - shaped 腰形的9.variable capacity 变量10.fixed capacity 定量11.eccentric cam 偏心凸轮12.speed reduction gearbox 减速齿轮箱13.pressure control valve 压力控制阀14.reducing valve 减压阀15.pilot valve 导阀16.flow control valve 流量控制阀17.bleed - off flow control 溢流流量控制阀18.series flow control 串联流量控制阀19.sequence valve 顺序阀7/ 920.sliding spool type 滑阀型Lesson191.deck machinery 甲板机械2.hatch cover 舱口盖3.mooring equipment 绞缆设备4.winch barrel 绞缆卷筒5.warp end 卷缆端6.spur gear transmission 直齿轮传动7.split windlass 分离式锚机8.cable lifter 锚链轮9.cable locker 锚链舱10.anchor capstan 锚绞盘11.cargo winch 起货机12.hoisting motor 起升马达13.luffing motor 变幅马达14.slewing motor 回转马达15.mooring winch 绞缆机Lesson201.steering gear 舵机2.rudder stock 舵杆3.rudder angle 舵角4.steering wheel 舵轮5.rotary vane type 转叶式6.variable delivery pump 变量泵7.control spindle 控制杆8. a floating lever feedback mechanism 浮动杆反馈机构9.audible and visual alarm 声、光报警10.rudder angle indicator 舵角指示器Lesson211.magnetic field 磁场2.carbon brush 碳刷3.field coil 励磁线圈4.power factor 功率因数5.alternating current generator 交流发电机6.automatic voltage regulator 自动电压调节器7.squirrel cage motor 鼠笼式电机8. D . C . exciter 直流励磁机9.shaft - driven alternator 轴带发电机10.emergency generator 应急发电机Lesson221.parallel operation 并车操作2.reverse power protection 逆功率保护3.reverse current protection 逆电流保护4.in phase 同相5.anticlockwise rotation 逆时针转动6.incoming generator 待并机7.bus frequency 汇流排频率8.synchronizing lamp 同步指示灯9.space heater 空间加热器10.АСВ( Air Circuit Breaker ) 空气断路器Lesson231.electrical energy 电能8/ 92.main switchboard 主配电板3.section board 区域配电板4.distribution board 分配电板5.deadfront type 前段不带电式6.“ draw out ” circuit breaker “抽出式”断路器7.tripping device 脱扣装置8.frequency meter 频率表9.voltage transformer 变压器10.curent transformer 电流变送器11.bus bar 汇流排12.“ plug in ” contact 插入式触头13.mechanical interlock 机械联锁14.no - volt coil 失压线圈15.isolating switch 隔离开关Lesson241.Classification Society 船级社2.drip - proof 防滴的3.watertight enclosure 水密机壳4.lead - acid battery 铅酸蓄电池5.alkaline battery 碱性蓄电池6.induction motor 感应式电机7.synchronous motor 同步电机8.induced e . m . f . 感应电动势9.direct on - line starting 直接起动10.star delta starter 星形三角形起动器11.auto transformer 自耦变压器12.stator resistance 定子电阻13.single phasing protection device 缺相保护装置14.overload protection device 过载保护设备15.undervoltage protective device 欠压保护装置16.“ no volts ” protective device 失压保护装置17.insulation resistance 绝缘电阻18.electric shock 电击19.artificial respiration 人工呼吸20.non - conducting material 非导电材料9/ 9。

一、专业词汇翻译1. Connecting rod 连杆/活塞杆2. four-stroke diesel engine 四冲程柴油机3. top dead center上止点/下止点4. reduction gear box 减速齿轮箱5. cooling jacket 冷却水套6. cylinder liner 气缸套7. piston skirt 活塞裙/活塞环8. running-in period 磨合期9.船用排气锅炉marine exhaust gas boiler 10. crankpin bearing 曲柄销轴承11.吸气行程suction stroke/压缩冲程12. circulating pump循环泵13. sea water cooling system海水冷却系统14. indicated power 指示功/效率15. compression ratio 压缩比16. 废热回收系统waste heat recovery system17.废气再循环exhaust gas recirculation 18. 扫气口scavenge port/扫气箱19.船级社classification society 20. 辅助风机auxiliary blower21. inlet valve 进气阀/排气阀22. 涡轮增压器turbocharger23. main starting valve主启动阀 24. 曲轴crankshaft25.机架/燃烧室/直流扫气/十字头滑块/导板……二、英译汉1．It is usually desirable to fit charge-air coolers to turbocharged two-stroke engines. The coolers are located between the turbo-blowers and the cylinders. As the charge-air density increases, the amount of air flowing into the cylinders is increased and as the charge-air temperature lowers, the exhaust temperature and the engine thermal loading are reduced.1．对于涡轮增压式二冲程发动机来说，通常希望能装有增压空气冷却器。

轮机英语词汇，带音标Aabnormal[æb’nэ:m(∂)l] adj. 反常的, 变态的 ,不正常的,abrasive [∂‘breısıv] adj.使磨损的, 粗糙的, (n.) 研磨料.absolute [‘æbs∂lu:t] adj. 完全的, 绝对的,静的。

acceleration [∂ksel∂reı(∂)n] n. 加速度.变速，过载。

accurate [‘ækjύr∂t] adj. 准确的, 精确的.精密的，已校准的,acetylene [∂‘set∂li:n] n. [化] 乙炔, 电气石.acid [‘æsıd] n. [化]酸, <俚>迷幻药, (adj.) 酸的,酸性的,act [ækt] vi. 行动，产生...的效果. (n.) 行为，法令，节目。

activator [`æktıveıt∂(r)] n. [化]催化剂，激励器，抖动器。

add [æd] v. 増加，添加，合计，累计.additive [∂’dıtıv] n.添加剂。

(adj.) 附加的，添加的.adhesive [∂d’hi:sıv] n.粘合剂，胶布。

(adj..) 粘着的，胶粘的，adjustable [∂’dЗ۸st∂b(∂)l] adj 可调整的；可调节的advicee [∂d’vaıs] n.忠告，建议，通知。

alarm [∂lа:m] n. 警报，警报器，报警装置。

alignment [∂’laınm∂nt] n. 队列，校直，调正，调准，定线。

alkaline [`ælk∂laın] adj.[化]碱的，碱性的。

allow [∂’laύ] vt.准许，许可，承认，打算。

allowance [∂’laύ∂ns] n. 津贴，补助，宽容，余量，容限，容差，公差。

alloy [‘ælэı] n. 合金。

轮机英语词汇汇总一．职位及工种(Titles and type of work) 1．船长 Captain2．大副 Chief officer3．二副 Second officer4．三副 Third officer5．四副 Fourth officer6．水手长 Boatswain7．水手 Sailor & Seaman8．木匠 Carpenter9．轮机长 Chief engineer10．大管轮 Second engineer11．二管轮 Third engineer12．三管轮 Fourth engineer13．机匠长 Chief motorman15．机匠 Fitter16．加油工 Oil man17．大电 Chief electrician18．电工 Electrician19．车间主任 Workshop director20．工长 Section chief21．班长 Fore man22．钳工 Fitter23．主管工程师 Engineer in charge24．机务&船东 Superintendent &Super &Owner 25．助理工程师 Assistant engineer26．验船师（机）Register27．验船师（船）Surveyor28．油漆工 Painter29．焊工 Welder30．大橱 Chief cook31．物料员 Store keeper32．加油工 Oiler33．机工 Mechanic34．甲板员 Deck man35．电线工 Wireman36．外包工 Laborer37．铸工 Molder38．管子工 Pipe fitter39．起重工 Crane operator二、柴油机类(Words about diesel engine) 1．主机 Main engine2．二冲程柴 Twostrokediesel engine3．四冲程柴 Forestrokediesel engine4．高速柴油 High speed diesel engine5．中速柴油 Middle speed diesel engine6．低速柴油机 Low speed diesel engine7．气缸盖(缸头) Cylinder head8．安全阀 Safety valve9．释放阀 Relief valve10．示功阀 Indicator valve11．示功考克 Indicator cock12．空气起动阀 Air starting valve13．起动空气分配器 Air starting distributor 14．油头(燃油喷射器) Fuel injector15．排气阀 Exhaust valve16．气缸套 Cylinder liner17．冷却水套 Cooling water jacket18．气缸注油器 Cylinder lubricator19．活塞 Piston20．活塞头 Piston crown21．活塞裙 Piston skirt22．活塞销 Piston gudgeon pin24．活塞杆 Piston rod25．活塞环 Piston ring26．活塞环槽 Piston ring groove27．压缩环 (气环) Compression ring28．刮油环 (油环) Oil scraper ring29．减磨令 Wear ring (copper ring)30．伸缩管(水拉管) Telescopic pipe31．活塞冷却空间 Piston cooling space32．填料箱(函) Stuffing box33．填料箱密封环 Sealing ring for Stuffing box 34．填料箱压缩环 Pressure ring for Stuffing box 35．填料箱刮油环 Scraper ring for Stuffing box 36．扫气箱 Scavenging receiver37．扫气口 Scavenging port38．排气口 Exhaust port39．十字头 Cross head40．十字头销 Crosshead pin41．十字头轴承 Crosshead bearing42．十字头滑块 Crosshead slipper43．滑块 Guide shoe44．十字头导板 Crosshead guide plate45．连杆 Connecting rod46．连杆大端轴承 Bid end bearing47．连杆小端轴承 Small end bearing48．曲柄轴承 Crank bearing49．曲柄销 Crank pin50．曲轴 Crank shaft51．曲轴颈 Crank journal52．曲柄臂 Crank web53．拐档差 Crank deflection54．主轴承 Main bearing55．主轴颈 Main journal56．轴承瓦 Bearing bush57．上轴瓦 Upper bearing bush58．上轴瓦 Upper half59．下轴瓦 Lower bearing bush60．下轴瓦 Lower half61．推力轴承 Thrust bearing62．推力块 Thrust pad63．推力盘 Thrust disc64．推力轴 Thrust shaft65．底座 Bed plate66．机架 Frame67．曲柄箱 Crank case68．曲柄箱导门 Crank case door69．曲柄箱防爆门 ExplosionproofCrank case.70．定时齿轮 Timing gear71．飞轮 Flying wheel72．凸轮 Cam73．凸轮轴 Cam shaft74．喷油凸轮 Fuel injection cam75．链条 Chain76．链条轮 Chain wheel77．链条箱 Chain box78．推杆 Push rod79．摇臂 Rocker arm80．排气阀 Exhaust valve81．吸气阀 Suction valve82．排气总管 Exhaust manifold83．进气总管 Air inlet manifold84．高压燃油管 High pressure fuel pipe 85．活塞冷却水管 Piston cooling water pipe 86．法兰 Flange87．贯穿螺栓 Tie bolt (tie rod)88．端盖 Side cover89．滑油泵 Lubricating oil pump90．燃油泵 Fuel oil pump91．滑油泵齿轮 Gear for lubricating oil pump 92．燃油泵齿轮 Gear for fuel oil pump93．叶轮 Impeller94．柱塞 Plunger95．导杆 Guide rod96．导套 Sleeve97．滚动轴承 Ball bearing98．滑动轴承 Sliding bearing99．推力滚动轴承 Thrust ball bearing100．推力面 Thrust surface (thrust side) 101．盘车机 Turning gear102．增压器 Turbocharger103．涡轮机(透平) Turbine104．涡轮 Turbine wheel105．涡轮叶片 Turbine blade106．喷嘴 Nozzle107．废气叶轮 Exhaust impeller108．废气叶轮片 Exhaust blade109．废气端 Exhaust side110．透平端 Turbine side111．转子轴 Rotor shaft112．油泵 L.O. pump113．换向装置 Reversing device114．换向伺服期 Reversing servomotor115．压气机(鼓风机) Blower116．膨胀接 Expansion joint117．调速器 governor118．飞重 Flying weight119．补偿阀 Compensate valve120．针阀 Needle valve121．开口销 Cotter pin122．轴封 Shaft seal123．机械密封 Machinery seal124．配电盘 Switchboard125．应急配电盘 Emergency switchboard 126．应急发电机 Emergency generator127．滤器 Filter128．细滤器 Filter129．粗滤器 Strainer130．滑油滤器 L.O. filter131．燃油滤器 F.O. filter132．空气消音器 Air intake silencer132．空气滤器 Air intake filter133．空气瓶 Air bottle (receiver)134．分油机 Separator135．油水分离器 Wateroil separator136．净油机 Purifier137．燃油净化器 F.O. purifier138．二氧化碳 CO2139．二氧化碳瓶 CO2 bottle140．正时齿轮 Timing gear141．导向棒装置 Guide bar142．注油器驱动 Lubricator driver143．链条张紧装置 Chain tightener144．凸轮轴传动轮 Chain wheel on cam shaft 145．中间链链传动轮 Intermediate chain wheel 146．注油器驱动装置 Lubricator drive147．链条张紧装置 Chain tightener148．滚筒导座 Roller guide housing149．应急操纵台 Emergency console150．力矩平衡器 Moment compensator151．主启动阀 Main starting valve152．启动空气分配器 Starting air distributor 153．喷油器 Fuel valve154．扫气系统 Scavenge air system155．安全帽 Safety cap156．机座 Bed plate157．轴向振动减振器 Axial vibration damper158 贯穿螺栓 Arrangement of stay bolt159．示功器驱动装置 Indicator driver160．端罩 End shields161．气缸架 Cylinder frame162 气阀传动装置 Valve operating device163．摇臂润滑油泵 Rocker arm lubricating oil pump 164．摇臂润滑油柜 Rocker arm lubricating tank 165．摇臂润滑滤器 Rocker arm lubricating filter 三、船舶机械类(Words about marinemachinery)1．船用锅炉 Marine boiler2．废气锅炉 Exhaust boiler3．辅锅炉 Donkey boiler4．组合式锅炉 Combined boiler5．火管 Fire tube6．给水管 Feed pipe7．炉膛 Furnace8．炉墙 Furnace wall9．火侧 Fire side10．水侧 Water side11．燃烧器 Oil burner12．安全阀 Safety valve13．上排污 Upper drain14．下排污 Lower drain15．锅炉皮阀 Mounting valve16．水位计 Water level gauge17．压力表 Pressure gauge18．主汽门 Main steam valve19．玻璃管 Glass tube20．空调装置 Airconditioning plant21．制冷装置 Refrigerating plant22．冰机 Fridge. Machine23．空气压缩机 Air compressor24．造水机 Fresh water generator25．板式冷却器 Plate type cooler26．机舱天车 Engine room crane27．天车导轨 Crane rail28．电磁阀 Solenoid valve29．舵机 Steering gear30．舵承 Rudder bearing carrier31．液压缸 Hydraulic cylinder32．废气涡轮增压器 Exhaust gas turbocharger 33．弹簧阀 Spring loaded valve34．冷凝器 Condenser35．分油器 Oil separator36．轴带发电机 Shaft generator37．焚烧炉 Oil burner38．分油机 Separator39．分离筒 Separator bowl40．配水盘装置 Paring disc device41．转数计 Revolution counter42．控制阀 Control valve43．辅机 Auxiliary machinery44．制冷装置 Refrigerating plant45．海水淡化装置 Sea water desalting plant 46．热交换器 Heat exchanger47．船用气瓶 Marine air bottle48．冷风机 Cooler unit49．防水风门 Fire damper50．气密挡板 Gas tight damper51．排气风机 Exhaust fan52．舱室通风机 Cabin fan53．机舱通风机 Engine room fan54．应急鼓风机 Emergency blower四、阀门(Words about valve)1．吸气阀 Suction valve2．排气阀 Exhaust valve3．控制阀 Control valve4．导阀 Pilot valve5．单向阀 Nonreturn valve6．口琴阀 Flap valve7．调节阀 Regulating valve8．液压阀 Hydraulic valve9．膨胀阀 Expansion valve10．给水阀 Feed valve11．排水阀 Discharge valve12．截止阀 Stop valve13．吹泄阀 Blowoff valve14．空气阀 Air valve15．泄放阀 Drain valve16．止回阀 Check valve17．海底阀 Sea valve18．回流阀 Retune valve19．节流阀 Throttle valve20．进气阀 Inlet valve21．出气阀 Outlet valve22．热力阀 Thermal valve23．中央阀 Center valve24．单向阀 One way valve25．二通阀 Two way valve26．三通阀 Triple valve27．旁通阀 Bypass valve28．换向阀 Changeover valve30．溢流阀 Overflow valve31．自闭阀 Selflocking valve32．针阀 Needle valve33．平衡阀 Balance valve34．循环阀 Circulation valve35．主阀 Main valve36．滑阀 Slide valve37．蝶阀 Butterflyvalve38．截止阀 Shutoffvalve39．闸板阀 Gate valve40．通海阀 Sea suction valve41．吹除阀 Sea chest cleaning valve 42．防浪阀 Storm valve43．舱壁阀 Bulkhead valve44．快关阀 Emergency shut off valve 45．呼吸阀 Breather valve五、泵类(Words about pump)1．电动泵 Motordrivenpump2．柱塞泵 Plunger pump3．叶片泵 Vane pump4．回转泵 Rotary pump5．齿轮泵 Gear pump6．往复泵 Reciprocating pump7．离心泵 Centrifugal pump8．真空泵 Vacuum pump9．螺杆泵 Screw pump10．喷射泵 Ejector pump11．冷却泵 Cooling pump12．淡水泵 Fresh water pump13．海水泵 Sea water pump14．给水泵 Feed water pump15．循环泵 Circulating pump16．锅炉给水泵 Boiler feed pump 17．卫生水泵 Sanitary pump18．压载泵 Ballast pump19．舱底泵 Bilge pump20．污水泵 Sewage pump21．燃油泵 Fuel pump22．高压油泵 High pressure pump 23．低压油泵 Low pressure pump 24．驳运泵 Transfer pump25．增压泵 Booster pump26．消防泵 Fire pump27．通用泵 G.S. pump28．旋涡泵 Regenerative29．蜗壳泵 Volute pump30．导叶泵 Diffuser pump31．单联泵 Simplex pump32．双联泵 Duplex pump33．多联泵 Multiplex pump34．活塞泵 Piston pump35．减摇泵 Antirollpump36．总用泵 General service pump 37．应急消防泵 Emergency fire pump 38．扫舱泵 Stripping pump39．货油泵 Cargo oil pump 40．滑油泵 Lubricating oil pump 六、甲板机械类（Deck machinery）1．锚机 Windlass2．锚机轴 Windlass shaft3．刹车带 Brake lining4．离合器 Clutch5．锚链轮 Anchor Chain wheel 6．轴承瓦 Bearing bush7．轴承盖 Bearing cover8．绞揽机 Capstan9．系揽绞车 Mooring winch 10．卷缆车 Reel 个11．钢丝绳 Wire rope12．卡环 Shackle13．缆绳 Mooring rope14．滑轮 Block15．刹车装置 Brake device 16．制链器 Anchor chain stopper 17．舱盖滚轮 Hatch cover wheel 18．舱盖铰链 Hatch cover hinge 19．液压油缸 Hydraulic jack 20．起货机 Cargo winch21．克令吊 Crane22．生活吊 Accommodation crane 23．吊杆 Derrick boom24．桅杆 Mast25．救生艇 Lifeboat26．艇架 Davit27．艇机 Lifeboat capstan 28．救生筏 Life raft29．救生衣 Life jacket七、工具类(Word about tools) 1．车床 Lathe2．刨床 Planing machine3．钻床 Drill machine4．砂轮机 Grinding machine 5．磨床 Grinder6．铣床 Milling machine7．镗床 Boring machine8．手锤 Engineer’s hammer 9．冲击板手 Impact wrench 10．板手 Spanner11．活络板手 Screw spanner12．梅花板手 Ring spanner13．呆扳手 Open spanner15．套筒板手 Socket spanner16．管子钳 Pipe spanner17．螺丝刀 Screw driver18．钢丝钳 Wire pliers19．尖嘴钳 Long nose pliers20．钢锯 Hack saw21．剪刀 Scissors22．手电筒 Torch23．扁铲(凿子) Chisel24．锉刀 File25．丝攻 Thread tap26．板牙 Thread die27．绞刀 Reamer28．刮刀 Scraper29．油石 Oil stone30．拔子(拉马) Puller31．沙布 Emery cloth32．破布 Rag33．卷尺 Measuring tape34．空心冲 Hole punch35．样冲 Joint punch36．油壶 Oil gun37．牛油枪 Grease gun38．手电钻 Handle drill39．钻头 Drill40．液压千斤 Hydraulic jack.41．塞尺 Feeler gauge42．游标卡尺 Vernier caliper43．外卡尺 Outside calipers44．内卡尺 Inside calipers45．螺纹量规 Screw gauge46．桥规 Bridge gauge47．电焊机 Electrode welding machine 48．气焊机 Gas welding machine 49．电焊钳 Electric welding pliers 50．气割枪 Cutting touch51．电焊条 Electric soldering iron 52．电工刀 Electrician knife53．电笔 Test pen54．剥线钳 Wire stripping pliers 55．圆规 Compass56．量表 Gauge57．拐档表 Crank deflection gauge58．深度规 Depth gauge59．千分表 Micrometer gauge60．台虎钳 Table vice61．柴油 Diesel oil62．滑油 Lubricating oil63．液压油 Hydraulic oil64．重油 Heavy oil65．燃油 Fuel oil66．黄油 Grease67．螺栓 Bolt68．螺帽 Nut69．垫片 Washer70．研磨沙 Grinding sand71．研磨膏 Grinding paste72．石棉板 Asbestos plate73．青壳纸 Fish paper74．盘根 Packing75．细钢丝 Thin steel wire76．密封圈 Rubber seal ring77．塑料管 Plastic pipe78．胶皮管 Rubber hose79．电灯泡 Electric bulb80．工作灯 Working lamp81．插头 Electric plug82．插座 Electric socket.93．喷砂机 Sand blaster outfit94．空气马达 Air motor95 油柜清洁器 Tank cleaning machine96．高压冲水机 High pressure hose for hydraulic 97．真空泵 Vacuum pump98．套筒扳手组 Socket wrench set99．深头套筒 Deep socket wrench100．套筒扳手 Box wrench101 单开口扳手 Single open end wrench102．双开口扳手 Double open end wrench103．转矩扳手 Torque wrench104．电动机扳手 Motor wrench105．侧剪钳 Slide cutting plier106．活节钳 Combination plier107．可调快速扳手 Speed wrench108．螺丝起子 Screwdriver109．偏向螺丝起子 Offset screw110．六角螺帽起子组 Hexagon nut drivers set111．手摇钻 Straight hand drill112．手工锯 Hacksaw frame113．锯片 Hacksaw blade114．砂纸 Silicon paper115．手拉葫芦 Chain block116．高压管 High pressure hose117．液压千金顶 Hydraulic jack118．锤子 Hammer119．平錾 Cold chisel120．活动扳手 Adjustable wrench121．螺丝刀 Screwdriver122．侧剪铗 Side cutting hipper123．螺栓剪 Cable cutter124．敲击管钳 Rap wrench125．砂轮 Grinding wheel126．老虎钳 Utility vise127．直梯 Straight ladder128．踏梯 Step ladder129．平台推车 Platform trunk130．搬平车 Gas cylinder carrier131．给油机 Grease lubricator132．强力油泵 Heavy duty pump oiler133．油壶 Oil jag134．麻花钻 Twist drill135．绞刀 Pin reamer136．旋转中心钻 Rolling center137 ．外径测微计 Outside micrometer with counter 138．六折式尺 Sixfolding rule139．弹性带尺 Convex rule140．不锈钢直尺 Stainless steel straight rule 141．平面规 Surface gauge142．平行直角定规 Precision flat try square 143．温度计 Thermometer八、常用物料(Material in common use)1．阀研磨剂 valve grinding compound2．电焊条 steel electrode3．气焊条 Steel welding wire4．细钢丝绳 Seizing wire5．刚焊条 Steel welding rod6．紫铜管 Copper tube7．乙炔气瓶 Acetylene cylinder8．木屑 Saw dust9．水泥 Cement10．石灰 Lime11．帆布手套 Canvas glove12．垫片 Gasket.13．氧气瓶 Oxygen cylinder14．抹布 Rag15．垫隙片 Shim16．电线 Wire17．电缆 Electric cylinder18．电池 Rag19．灯泡 Bulb20．胶布 Insulating tape21．插头 Plug22．插座 Socket23．保险丝 Fuse24．不锈钢 Stainless steel25．铸铁 Cast iron26．黄铜 Brass27．青铜 Bronze28．铝合金 Aluminium alloy29．橡胶 Rubber30．石棉 Asbestus31．低碳钢 Soft steel32．高碳钢 Highcarbon steel33．合金钢 Alloy steel34．木材 Wood35．塑料 Plastic36．球墨铸铁 Nodular iron九、常用紧固件(Part of fixation in common use)1．螺栓 Bolt2．螺丝 Screw3．螺母 Nut4．方头螺栓 Sq head bolt5．埋头螺栓 Counter sunk head screw6．套筒螺栓 Socket head bolt7．定位螺栓 Set screw8．十字接头 Cross9．锥形销 Taper pin10．锁紧螺母 Lock nut11．六角头螺栓 Hex head bolt十、常用油类(Oil in common use)1．汽油 Gas oil2．煤油 Kerosene3．润滑油 Lubricating oil4．汽缸油 Cylinder oil5．压缩机油 Compressor oil6．齿轮油 Gear oil7．机油 Motor oil8．凡士林 Vaseline9．燃油 Fuel oil10．油脂 Grease11．柴油 Diesel oil十一、常用量词(Quantifier in common use) 1．件，只，个 Piece2．条，张，片 Sheet3．双 Pair4．套，组，副 Set.5．盒 Box6．箱 Case7．瓶 Bottle8．米 Meter9．厘米 Centimeter10．毫米 Millimeter11．公斤 Kilogram12．克 Gram13．公升 Liter14．平方 Square15．袋 Bag16．码 Yard17．吨 Ton18．磅 Pound19．加仑 Gallon20．立方 Cubic十二、国家名称(Name of country)1．中国 China2．美国 American3．日本 Japan4．英国 Britain5．法国 France6．德国 German7．韩国 South Korea8．希腊 Greece9．泰国 Thailand10．印度 India11．挪威 Norway12．俄罗斯 Russia13．新加坡 Singapore14．澳大利亚 Australia15．伊朗 Iran16．丹麦 Denmark17．加拿大 Canada18．丹麦 Denmark19．芬兰 Finland20．巴基斯坦 Pakistan21．意大利 Italy十三、常用缩语(abbreviation in common use)1．主机 M/E2．付机 A/E3．阀 V/V4．泵 P/P5．备车 St/by6．完车 F.W.E.7．前进三 FAHD8．微速后退 D.S.Ast9．前进二 H.Ahd10．高压 H.P.11．低压 L.P.12．重油/柴油 H.O./D.O.13．前后 F/A14．左舷 P: port15．无人机舱 UMS16．自动 Auto17．气缸 Cyl18．燃油柜 19．滑油柜 20．沉淀柜 .21．排出 Disc22．吸入 Suct23．柴油柜 十四、船用动态常用单词(marine tends word) 1．停靠 Alongside2．接近 Approach3．停泊 Berth4．浮筒 Buoy5．码头 Pier6．港口 Port7．移泊 Shift8．航次 Voyage9．试验 Try10．值班 Watch11．航行 Sail十五、船舶机电设备操作词汇(manipulate of marine equipment) 1．调整 Adjust2．压载 Ballast3．转换 Change over4．清洁 Clean5．联接 Connect6．排放压载 Deballast7．放残水 Drain8．卸载 Off9．油漆 Paint10．接通 Put on11．吹灰 Soot blown12．开始 Start13．顶端 Top14．洗 Wash15．吹 Blow16．检查 Check17．铲 Chip18．断开 Cut out19．排放 Discharge20．除垢 Descale21．检验 Examine22．受载 On(load)23．用泵排出 Pump out24．调整 Set25．停止 Stop26．调驳 Transfer27．加满 Top up十六、故障常用单词(words about malfunction)1．失常的 Abnormal2．烧坏 Burn3．堵塞 Clog4．裂缝 Crack5．变形 Deform6．毁坏 Destroy7．磨损 Wear8．出故障 In trouble9．敲击 Knock10．松开 Loose11．不对中 Misalign12．不足的 Insufficient13．失灵 Out of order14．过载 Overload15．过度磨损 Overworn16．尺寸过大 Oversized17．尺寸过小 Undersized18．振动 Vibrate19．不平的 Uneven20．不准确 Inaccurate21．全船断电 Black out22．出故障 Fail23．关掉 Shut off24．弯曲 Bend25．停车 Break drown26．腐蚀 Corrode27．腐蚀的 Corrosive28．损坏 Damage29．有毛病的 Faulty30．有缺陷的 Defective31．破裂 Fracture32．卡住 Jam33．漏泄 Leak34．漏泄的 Leaky35．融化 Melt36．噪声 Noise37．过热 Overheat38．咬住 Seize39．紧的 Tight40．松的 Loosen41．发现 Find42．停止 Stop43．脏的 Dirty44．油污的 greasy45．失效的 ineffective46．椭圆形的 oval47．点不着火 misfire48．接错 misjoin49．放错 misplace50．老化 perish51．麻点 pit52．凸起 ridge53．划伤 score54．拉痕 scuff十七、保养检修常用词汇(Words about maintain and examination) 1．卡死 Blind2．用卡钳量 Caliper3．关闭 Close4．解体 Disassemble5．安装 Fix6．组装 Box up7．检验 Check8．拆卸 Dismantle9．装配 Fit10．紧固 Fasten11．测量 Gauge12．安装 Install13．测量 Measure14．打开 Open15．上油漆 Paint16．换新 Renew17．上紧 Tighten18．洗 Wash19．涂油脂 Grease20．松开 Loosen21．加油 Oil22．检修 Overhaul23．重新组装 Reassemble 24．测取读数 Take reading 25．拧开螺栓 Unbolt26．抽出 Withdraw十九、时间、季节与方向(Time、Season and Direction) 1．星期一 Monday2．星期二 Tuesday3．星期三 Wednesday4．星期四 Thursday5．星期五 Friday6．星期六 Saturday7．星期日 Sunday8．春季 Spring9．夏季 Summer10．秋季 Autumn11．冬季 Winter12．一月 January13．二月 February14．三月 March15．四月 April16．五月 May17．六月 June18．七月 July19．八月 August20．九月 September21．十月 October22．十一月 November23．十二月 December24．小时 Hour25．分钟 Minute26．秒 Second27．月 Month28．天 Day29．夜 Night30．周 Week31．早晨、上午 Morning32．下午 Afternoon33．傍晚 Evening34．正午 Noon35．今天 Today36．昨天 Yesterday37．明天 Tomorrow38．前天 The day before yesterday 39．后天 The day after tomorrow40．本周 This week41．上周 Last week42．下周 Next week43．九月十日 Sep.10 th44．去年 Last year45．明年 Next year46．上周二 Last Tuesday47．下周一 Next Monday48．东 East49．西 West50．南 South51．北 North52．西北 Northwest53．东北 Northeast54．东南 Southeast55．西南 Southwest56．世纪 Century二十、常用词组（Phrases in common use）1 已无法修复 beyond repair2．尺寸过大 oversized3．反应缓慢 slow function4．不正常 out of order5 不合标准 not up to standard6．不准确 inaccurate7．失去作用 out of function8．轧住 seized9．过热 overheated10 过度磨损 ound excessive wear 11．过度磨掉 worn out12．有一点倾斜 a little bit inclined 13．不正常 abnormal14．因过热而损坏 founDestroyed by overheating15．龟裂 chapped16．塌陷 collapsed17．运转失灵 out of operation18．呈椭圆形 oval19．拉痕 scored20．拉毛 scuffed21．变形 deformed22．松动 loose23．油污 greasy24．肮脏 dirty25．咬住 stuck26．挤压 squeezed27．弯曲 bent28．故障 faulty29．损坏 damaged30．破碎成片 broken to pieces31．部分剥离 partly detached32．部分堵塞 partly choked33．剧烈震动 violent vibration 34．烧坏 burnt35．断裂 fractured36．接地 earthed37．敲缸 knocking38．溶化 melted away39．发现泄漏 leaking ( leaky) 40．冻结 stuck fast by icing41．锈蚀 rusty42．失效 ineffective43．故障 out of order44．结霜 frosted45．丢失 lost46．出故障 in trouble47．失灵 out of order48．失灵 out of action49．不一致 out of operation50．错位 out of place二十一、常用动词和例句(Verb in common use and example)1．借 borrow我要向你借这份图纸I want to borrow the drawing from you.我可以向你借这个手锤吗?May I borrow the hammer from you?2．裂 break阀杆断裂了The valve spindle is broken.滚动轴承断裂成碎片了The ball bearing are broken to pieces.3．加强 build up叶轮应该堆焊 The impeller should be built upby welding.4．烧 burn电动机烧了 The motor is burnt.5．进行 carry out应进行负载试验The load test should be carried out.6．吹 blow管子必须用压缩空气吹清The pipe should be blown with compressed air. 7．铸 cast按原样铸造一个 Cast one piece as per sample. 8．引起 cause损坏是有剧烈振动引起的The damage was caused by violent vibration. 9．倒角 chamfer油槽须倒角 Oil groove is to be chamfered.法兰切削后须倒角The flange should be chamfered after being machined.10．换掉 change把它们换掉,否则我拒绝验收Have them changed, otherwise I refuse to accept them.11．龟裂 chap轴瓦上的白合金龟裂了 The white metal onthe bearing bush is chapped.12．核查 check用桥规核查主轴承 Check the main bearingwith bridge gauge.修理前后要核查拐档差Check the crankshaft deflection before andafter repair.13．清洁 clean装前须清洁 Clean it before fit back.14．阻塞 clog燃油滤器阻塞了 The fuel filter is clogged.15．涂漆 coat用红丹涂管子 Coat the pipe with red lead.泵壳里涂防护漆The pump casing is to be coated with antifouling. 16．完成 complete finish你什么时候能完成修理工作?When can you complete (finish) the repair job? 17．连接 connect把电动机和淡水泵连接起来 Connect the motorwith the fresh water pump18．腐蚀 corrode泵壳和叶轮均有腐蚀 The pump casing andimpeller are corroded.19．盖 cover请把所有卸下的部件盖起来Please cover all the removed parts.20．裂二号缸头裂开穿透至冷却水空间No.2 cylinder head is cracked.21．吊 crane把液压马达吊上岸去修理Crane the hydraulic motor ashore for repair. 22．割 cut把底座割掉Cut off the bedplate.23．损坏 damage滚动轴承严重损坏The ball bearings are seriously damaged.24．脱落 detach白合金部分脱落了The white metal is partly detached.25．查看 detect查看氟里昂系统有无泄漏Detect the Freon system for leakage.26．解体 disassemble解体,清洁并检查高压油泵Disassemble, clean and check the H.P. fuel pump. 27．脱开 disconnect把起动空气管脱开Disconnect the starting air pipe.将发电机与原动机脱开。

轮机英语- 轮机工程原理（英文版）Principles of Marine Engineering2010. 10ContentsContents (2)1 Main propulsion plant (篇标题) (3)1.1 Ships and machinery (章标题) (3)1.2 Diesel engine (9)1.3 Shaft and propellers (46)2 Marine auxiliary machinery (55)2.1 boilers (55)2.2 Pumps (55)2.3 Refrigeration, air conditioning and ventilation (55)2.4 Pollution prevention devices (55)2.5 Centrifugal separator and fresh water generator (55)2.6 Deck machinery (55)3 Electrical equipment and automatic control (56)3.1 Alternating current generators (56)3.2 Main switchboard and distribution system (56)3.3 Marine electrical equipment (56)3.4 Marine automatic control (56)4 Watch keeping and equipment operation (57)4.1 operation procedures (57)4.2 Safety operation (57)4.3 Stores and spare parts (57)4.4 Shipp repair and docking (57)4.5 Pollution prevention operation and Port State Control (57)5 International conventions and regulations (58)5.1 STCW (58)5.2 MAPROL (58)5.3 SOLAS (58)5.4 ISM (58)5.5 ISPS (58)6 Marine business writing (59)6.1 Engine log book (59)6.2 Repair list (59)6.3 Store order and spare parts requisition form (59)6.4 Accident report (59)6.5 Engineer’s reports, letters, faxes and emails (59)Index ............................................................................................................... 错误！未定义书签。