注塑常用术语英文表达

  • 格式:doc
  • 大小:15.00 KB
  • 文档页数:3

1.雾气 Moisture Streaks

2.玻纤分配不均 Glass Fiber Streaks

3。困气 Gas Trap Effect

4.银丝纹 Sliver Marks

5.结合线 Weld Line

6。水波痕 Water Wave Effect

7.黑点 Dark Sport

8。顶出印 Visible Ejector Marks

9。变形 Deformation During Demolding

10.填充不足 Short Filling

11。冷料流痕 Cold Slug

12。进胶口点不良 Dull Spots Near The Sprue

13.喷射痕 Jetting

14.表面起层 Flaking Of The Surface Layer

15.浮泡 Entrapped Air

16。过热变色 Burnt Streaks

17.龟裂 Stress Crack

18。缩水痕 Sink Marks

19。真空气泡 Density Bubble

20。披锋 Flash

21.擦伤印 Scratch MarksGlass fiber rich surface/glass emergence on the surface

22 尺寸过大 Over dimension

23尺寸过小 Under dimension

24 翘曲 Warpage/warped

25 收缩 Shrinkage/shrink

26 缩影 Sink marks

27 打不满 Short shot/short molding

塑料模具mould of plastics

注塑模具injection mould

冲压模具die

模架mould base

定模座板Top clamping plate

Top plate

Fixed clamp plate

水口推板stripper plate

A板A plate

B板B plate

支承板 support plate

方铁 spacer plate

底针板 ejector plate

面针板 ejector retainer plate

回针 Return pin

导柱 Guide pin

有托导套 Shoulder Guide bush 直导套 Straight Guide bush

动模座板Bottom clamp plate

Moving clamp plate

基准线datum line

基准面datum plan

型芯固定板core—retainer plate

凸模固定板punch-retainer plate

顶针ejector pin

单腔模具single cavity mould

多腔模具multi-cavity mould

多浇口multi—gating

浇口gate

缺料starving

排气breathing

光泽gloss

合模力mould clamping force

锁模力mould locking force

挤出extrusion

开裂crack

循环时间cycle time

老化aging

螺杆screw

麻点pit

嵌件insert

活动镶件movable insert

起垩chalking

浇注系统feed system

主流道 sprue

分流道runner

浇口gate

直浇口direct gate , sprue gate

轮辐浇口spoke gate , spider gate

点浇口pin-point gate

测浇口edge gate

潜伏浇口submarine gate , tunnel gate

料穴cold-slug well

浇口套sprue bush

流道板runner plate

排飞槽vent

分型线(面)parting line

定模stationary mould,Fixed mould

动模movable mould, movable half

上模upper mould, upper half

下模lower mould, lower half 型腔cavity

凹模cavity plate,cavity block

拼块split

定位销dowel

定位销孔dowel hole

型芯core

斜销angle pin, finger cam

滑块slide

滑块导板slide guide strip

楔紧块heel block, wedge lock

拉料杆sprue puller

定位环locating ring

冷却通cooling channel

脱模斜度draft

滑动型芯slide core

螺纹型芯threaded core

热流道模具hot—runner mould

绝热流道模insulated runner mould

熔合纹weld line (flow line)

三板式模具three plate mould

脱模ejection

换模腔模具 interchangeable cavity mould

脱模剂release agent

注射能力shot capacity

注射速率injection rate

注射压力injection pressure

差色剂colorant

保压时间holdup time

闭模时间closing time

定型装置sizing system

阴模female mould,cavity block

阳模male mould

电加工设备Electron Discharge Machining

数控加工中心CNC machine center

万能铁床Universal milling machine

卧式刨床Horizontal planer

车床Engine lathe

平面磨床Surface grinding machine

去磁机Demagnetization machine

万能摇臂钻床Universal radial movable driller

立式钻床Vertical driller

超声波清洗机Ultrasonic clearing machine