船用英语

一、船舶类型常用英语ship, vessel 船，船舶boat, craft 艇sampan 舢板, 小船manpowered boat 人力船sailor; sailing boat 帆船motor sailor 机帆船power-driven ship 机动船paddle steamer, paddle wheel vessel 明轮船screw ship; propeller vessel 螺旋桨船airscrew ship; aerial propeller vessel 空气螺旋桨船hovercraft; aircushion craft 气垫船hydrofoil 水翼船hydrojet propelled boat, water jet boat 喷水船steamship; steamer 蒸汽机船motor ship 内燃机船diesel ship 柴油机船electrically-propelled ship 电力推进船steam turbine ship 汽轮机船gas turbine ship 燃气轮机船nuclear-power ship 核动力船deck ship 甲板船flush deck ship 平甲板船raised quarter-deck ship 尾升高甲板船well-deck ship 半舱船single side ship 单舷长大舱口船three-island ship 三岛式船double shell ship 双壳船riveted ship 铆接船welded ship 焊接船transversely framed ship 横骨架式船longitudinally framed ship 纵骨架式船combined framed ship 混合骨架式船sea-going vessel 海船ocean-going vessel 远洋船coaster 沿海船channel ship 海峡船inland waterway vessel 内河船civil ship; merchant ship 民用船；商船transport ship 运输船pleasure yacht 游艇passenger ship 客船coasting passenger and cargo ship沿海客货船passenger and auto-car carrier 旅客及汽车运输船tourist ship; passenger carrier 旅游船cargo ship; freighter 货船cargo liner 定期货船tramp ship 不定期货船container ship 集装箱船full-container ship 全集装箱船semi-container ship 半集装箱船multi-purpose container ship 多用途集装箱船general cargo ship/vessel/carrier 杂货船bulk (cargo) carrier 散货船ore carrier 矿砂船grain carrier 运粮船coal carrier; coaler 运煤船lumber(timber) carrier 运木船cattle carrier 运牲畜船multi-purpose ship 多用途船liquid cargo ship 液体货货船chemical tank 化学品液货船liquid chemical tanker 液体化学品船liquefied gas carrier 液化气体船liquefied petroleum gas tanker (LPG) 液化石油气运输船liquefied natural gas tanker (LNG) 液化天然气运输船tanker; oil tanker 油轮super tanker 超级油轮VLCC (very large crude carrier) (吨位在20万至30 万吨之间的) 巨型油轮ULCC (ultra-large crude carrier) (吨位在30万至50万吨之间的) 超巨型油船refrigerated ship; cold storage ship 冷藏船roll-on/roll-off ship (RO/RO ship) 滚装船ferry 渡船passenger ferry 旅客渡船freight ferry 货物渡船fishing vessel(boat) 渔轮trawler 拖网渔轮barge carrier; lighter aboard ship(LASH)载驳船barge; lighter 驳船deck barge 甲板驳well-deck barge 半舱驳double shell barge 双壳驳single side barge 单舷长大舱口驳oil barge 油驳container barge 集装箱驳船RO/RO barge 滚装驳船liquefied gas barge 液化气体驳hopper barge 开底泥驳split hopper barge 对开泥驳pusher; pushboat 顶推船；推船working ship 工程船tug; tugboat; towboat 拖船harbor tug 港作拖船rescue tug 救助拖轮salvage ship 救捞船dredger 挖泥船trailing suction dredge 耙吸挖泥船cutter suction dredger 绞吸挖泥船bucket wheel dredger 斗轮挖泥船bucket dredger 链斗挖泥船reclamation craft 吹泥船grab dredger 抓斗挖泥船dipper dredger 铲斗挖泥船floating pitter; drive pitter 打桩船floating crane; derrick boat 起重船floating dock 浮船坞cable layer; cable ship 布缆船scientific surveying ship 科学考察船research ship 科学调查船oceanographic research vessel 海洋调查船surveying ship 测量船ice-breaker 破冰船pontoon 浮舟; 浮桥; 趸船, 浮码头high speed craft 高速船passenger catamaran 双体客船vehicle ferry catamaran 双体车辆渡船vehicle-passenger ferry catamaran 双体车客渡船pontoon catamaran 双体趸船二、船舶结构常用英语center line 中心线，中线athwartships 横对船体（与船首尾线直交）bevel 斜角；斜面base line 基线amidships 在船中部；在纵中线上designed waterline breadth 设计水线宽designed waterline length 设计水线长draft 吃水former/aft draft 首/尾吃水draft figures 吃水尺度intersection 交点；交叉；横断面knuckle 折角线length between perpendicular 垂线间长length overall 总长load waterline length 满载水线长register length (breadth; depth) 登记长度（宽度、深度）freeboard 干舷rise of floor (dead; rise) 舭高；船底loadline mark 载重水线标记fresh water load line (F.) 淡水载重线fresh water timber load line (L.F.) 淡水木材载重线tropical fresh water load line (TF) 热带淡水载重线tropical load line (T) 热带载重线summer load line(S) 夏季载重线summer freshwater load line(F) 夏季淡水载重线winter load line(W) 冬季载重线winter North Atlantic load line(WNA) 冬季北大西洋载重线even keel （首尾）等吃水，平载extreme breadth 最大宽度floatable length 可浸长度sheer at forward (after) perpendicular 首尾舷弧sheer line 舷弧线accommodation 居住舱室accommodation deck 起居舱室；旅客甲板accommodation ladder 舷梯accommodation ladder platform 舷梯平台accommodation ladder manrope 舷梯扶索after body 后（部船）体after peak bulkhead 艉尖舱舱壁after peak tank 艉尖舱air hole 空气孔air pipe 空气管appendage （船体水线下的）附体；附件auxiliary machinery 辅助机械；辅机balanced rudder 平衡舵ballast 压载（物）ballast line 压载水管系ballast pump 压载水泵ballast pumping system 压载水系统ballast tank(water) 压载舱（水）batten 板条；压条（封仓用）batten-ceiling （货舱内）护舱条，护板beam 横梁beam bracket 梁肘板bearding 交合线，榫（艏柱或艉柱上）bending moment 弯矩bilge 舭部；舱底；（船底）污水沟bilge bracket 舭肘板bilge keel(chock, piece) 舭龙骨bilge knee 舭肘板bilge line 舭水管系bilge main 舭水总管bilge pipe (suction) 舭吸水管bilge pump 舭水泵bilge strake(plate) 舭列板bilge well 污水井bitt 系缆桩bollard 系缆桩；系船柱；双系柱bolster 枕垫bonnet 烟囱帽；机罩boom 杆；吊杆；桁；叉架boom crutch(support; rest) 吊杆支架bossing 尾管突出部；轴包套bottom frame 船底横骨bottom longitudinal 船底纵骨bottom plate 船底板bow 船首，船头bow fender 艏护垫bow flare 艏部外飘bow thruster 首侧推器bracket 肘板；（三角）拖架breakwater 挡浪板bridge 桥；桥楼；驾驶台bulb angle 圆头角材bulbous bow 球形船首，球鼻首bulb stern 球形船尾bulkhead 舱壁bulkhead plating 舱壁板bulkhead stiffener 舱壁扶强材bulwark 舷墙bulwark plating 舷墙板bulwark stay 舷墙扶强材bunker tank 燃料舱bushing 衬套butt 端接；残片butt joint(seam) 平接缝butt riveting 对接铆butt welding 对接焊butterfly clip 蝴蝶夹bypass valve 旁通阀cable stopper 止链器camber 翘曲camber of beam 梁拱cant beam 斜梁cant bracket 斜角板cant frame 斜肋骨cantilever 悬臂梁capstan 绞盘；绞缆机cargo batten 货舱护板cargo block 吊货滑车cargo port 装货舷梯，舷门cat walk （油轮上的）天桥，步桥center girder 中底桁center strake 中央内底板chafing plate 防擦板chafing ring 防擦环chain lock(well) 锚链舱chain pipe 锚链管chain stopper 止链器chock 导缆器；垫木clamp plate 夹板，压板cleat 羊角；系绳铁栓；防滑条coaming 围板；舱口围板cofferdam 隔离舱collar plate 封板collision bulkhead 船首舱壁；防撞舱壁companion way(hatch) 升降口corrugated bulkhead 槽形舱壁corrugation 皱；槽形；波形cross deck structure 舱间甲板结构crossing strength member 交叉强力构件cruiser stern 巡洋舰型船尾curtain plate 幕板cut out 开口；切davit 吊艇架；吊艇柱deck 甲板deck beam 甲板横梁deckhouse 甲板室deck line 甲板线deck longitudinal 甲板纵骨deck stringer(plate) 甲板边板deep tank 深舱derrick 吊杆diaphragm 隔板double bottom 双层底doubling plate 双层焊合板drain hole 排水孔duct keel 箱形龙骨dunnage 垫舱（物料）；衬垫dunnage wood 垫木dynamic load 动载荷end bracket 端肘板escape trunk （船内）应急通道engine bed 机座engine casing 机舱围壁escape scuttle （船内）应急出口escape vent 脱险口expansion joint 伸缩接头expansion trunk(tank) （油船）膨胀深井extension bracket 延伸肘板face plate 面板fender 碰垫；护舷材fender bar 护舷条fair lead 导缆器flame screen 防焰罩flange 折边flanged bracket 折边肘板flat keel 平板龙骨floor 肋板folding door 折门forecastle deck 艏楼甲板fore peak tank （船的）首舱；前尖舱forward perpendicular 首垂线foundation 底座frame 肋骨frame number 肋骨跨数frame space 肋距freeing port 甲板排水孔；放水孔gangway (gang ladder or gang board) 舷梯gasket 垫圈，垫料（集）密封垫general service pipe (G.S pump) 通用泵，总用泵girder 桁材gooseneck(parity iron) 鹅颈头；吊杆弯头grating 格子板；滑铁板ground tackle 锚泊索具gunwale 舷缘；舷边gunwale angle 舷边角钢gunwale bar 舷边角材gunwale railing 舷边栏杆gunwale tank 舷侧水柜（甲板下）gusset 角板；扣板gutter （甲板）水沟；槽沟gutter angle; waterway angle （舷侧）排水沟角钢gypsy 绞筒（锚机绞车上的）handrail 舷墙扶手hanging rudder; hinged rudder 吊舵；悬舵hatch; hatchway; hatch opening 舱口hatch bar 封舱压条hatch batten 舱口边压条hatch beam (web) 舱口大梁hatch booby 活动舱口盖hatch coaming 舱口板hatch cover 舱口盖hatch end beam 舱口端梁hatch moulding 舱口椽材hatch side girder 舱口纵桁hatch tarpaulin 盖舱布hatch trunk 舱口围阱hawse pipe 锚链管hawser 绳索；大缆heel 踵材；横倾hinged cover(door) 铰链盖（门）hold 货舱hold beam 舱内梁hold frame 舱内肋骨hold ladder 舱内梯hold stanchion(pillar) 舱内支柱hold stringer 舱内纵桁hopper 漏斗；开舱泥驳hopper tank 底边舱hopper tank sloping plating 底边舱斜板horizontal margin plate 水平内底板horizontal girder 水平桁horizontal stiffener 水平扶强材（防挠材）hull 船壳，船体hull construction 船体结构hull plating 船壳板hull strength 船体强度inner bottom 内底inner bottom plating 内底板insert plate 嵌板；衬板jack 千斤顶jack ladder 绳梯Jacob's ladder 软梯；绳梯Joggled joint 折接；弯合joggling machine 折曲机keel 龙骨keelblock 龙骨墩keel line 龙骨线；艏艉线keel plate 龙骨板keel rail （救生艇）艇底把手keelson 内龙骨kingpost 起重柱；将军柱knee 肘板；弯头knee of the deck 甲板梁肘板lightening hole 减轻孔lignum vitae 铁梨木local strength 局部强度local stress 局部应力longitudinal 纵骨；纵材；纵桁longitudinal bulkhead 纵舱壁longitudinal bending 纵向弯曲longitudinal framing system 纵骨架式longitudinal strength 纵向强度lug 耳板main deck 主甲板main frame 主肋骨manhole 人孔man hole door 人孔盖man hole coaming 人孔围板moment of inertia 惯性矩margin plate 内底边板molded breadth 型宽molded depth 型深mooring hole 导缆孔mooring post 系缆柱；岸柱mud box 泥箱non-return valve 止回阀non-watertight bulkhead 非水密舱壁notch 切口；槽口；刻痕oscillating load 振动负荷parallel middle body 平行中体panel stiffener 板格扶强材panting arrangement 防挠振结构panting beam 防挠振梁panting stringer 防挠振纵桁pillar 支柱；墩pintle 舵销plane bulkhead 平面舱壁plane keel 平板龙骨pump room 泵舱helm(rudder) pintle 舵销horizontal margin plate 水平内底边板out bottom plating 外底板platform 平台plating 壳板plimsoll mark 载重线标志poop 艉楼；船尾poop deck 艉楼甲板port 舷门；舱门；（装货）口；窗；门；孔porthole 舷窗；（装货）舷门propeller; propellor 推进器；螺旋桨propeller aperture 螺旋桨空间propeller boss(bub) 螺旋桨毂propeller shaft 艉轴racking （船体）横向挠度rail 扶手；栏杆rolling 横摇round of beam 梁拱round stern 圆（船）尾rudder 舵rudder carrier 舵托rudder casing 舵杆管rudder pintle 舵针；舵栓rudder plate; rudder blade 舵叶；舵板rudder post 舵柱rudder stock 舵杆rudder trunk 舵杆围壁；舵杆管rung （梯子）踏步；横档scallop 扇形开孔scantling 构件尺寸scantling of the structure 结构尺寸scarf; scarph 嵌接处；斜面；斜接scarf joint 斜（嵌）接scarf weld （斜面）焊接scarfing bracket 嵌接肘板scupper 排水孔scupper pipe 排水管scuttle 舷窗；人孔（盖）；小舱口盖seam 焊缝；接缝section 剖面section modulus 剖面模数semi-balanced rudder 半平衡舵shaft 轴shaft bracket 轴架shaft tube; stern tube 艉轴管shaft tunnel(alley; passage; trunk) 轴隧；地轴弄shedder plate 泄板；斜板sheer 舷弧；偏航sheer strake 舷顶列板shell 船壳；壳shell frame 舷侧肋骨shell plating 船壳板；外板shell strake; outside plating 船体外板shelter deck 遮蔽甲板shifting beam 活动舱口梁shifting board (or plank) 止移板（散装谷类）；防动板side girder 旁桁材side longitudinal 舷侧纵骨side plating 舷侧外板side strake 舷侧列板single bottom 单层底skid 护舷木；垫板skylight 天窗slanting plate 斜板slop tank 污油水舱sloping plate 斜板sloping plate longitudinal 斜板纵骨slot 槽；开缝sluice 水密门；水闸sluice valve 闸阀sniped end 削斜端soft toe 软趾solid floor 实肋板sounding pipe 测量管；测深管stabilizer 减摇装置stabilizing tank 减摇水舱staging 构架；台架；脚手架stanchion 支柱；栏杆柱static load 静载荷stay 支柱；撑条；支索stay bar(or rod) 撑杆stay plate 撑板stem 艏；艏柱；艏材stem post 艏柱stern 船尾，艉部stern counter 船尾突出体stern shaft; propeller shaft 艉轴stern poop 艉楼stern post 尾柱stiffener 防挠材；扶强材；加固物stool 托架，座，凳strake 列板strength calculation 强度计算strength deck 强力甲板stringer 纵桁stringer plate 甲板边板structural member 构件structural strength 结构强度strum box （舱底水）过滤箱strut 撑材，支柱，轴架stuffing box 填料箱superstructure 上层建筑tail (end) shaft 艉轴tarpaulin 防水油布，帆布，舱盖布thrust bearing(block) 推力轴承thrust shaft collars 推力环tieplate 带板，牵板，连接板topside tank 顶边舱；上边柜topside tank sloping plating 顶边舱斜板torsion 扭转torsion strength 扭转强度transom stern 方形船尾transverse 横梁，横材transverse bulkhead 横舱壁transverse frame 横肋骨，横框transverse framing system 横骨架式transverse ring 横环transverse strength 横向强度tripping bracket 防倾肘板tween deck 中间甲板tween deck frame 甲板间肋骨twisting distortion 扭转变形twisting moment 扭转力矩tunnel 轴隧，隧道，风筒tunnel escape 轴隧应急出口tunnel shaft bearing 中间轴支撑轴承ullage pipe (port) 油位测定管（孔）ullage space 空挡空间upper deck 上甲板upper (reverse) frame 内底横骨upper (lower) shelf plate 上（下）支架板upper (lower) stool 上（下）托架ventilator 通风筒vertical ballast trunk 竖向压载通道vertical girder 竖桁warping chocks 滚轮导缆钳wash bulkhead 可荡舱壁，挡水舱壁watertight bulkhead 水密舱壁watertight deck 水密门weather deck 露天甲板web beam 强横梁，桁板横梁web frame 加强肋骨，框架肋骨，桁板肋骨web plate 腹板wedge 楔木，楔子winch 起货机winch-head 绞车卷筒windlass 起锚机wing tank 翼舱，翼柜wire clip 钢缆夹wire reel 卷缆车，钢丝滚筒三、船舶材料及工艺常用英语A.Shipbuilding material (造船材料)T-bar T型钢Z-bar Z型钢I-B ar 工字钢channel bar 槽钢angle steel 角钢equal angle steel 等边角钢unequal angle steel 不等边角钢offset bulb plate 球扁钢flat plate 钢板round steel 圆钢half round steel 半圆钢steel pipe 钢管alloy steel 合金钢special steel 特种钢tempering steel 回火钢材low carbon steel 低碳钢high tensile steel 高强度钢copper 紫铜brass 黄铜aluminum alloy 铝合金stainless steel 不锈钢mechanical property 机械性能tensile test 拉伸试验bend test 弯曲试验impact test 冲击试验torsion test 扭转试验torsion strength 抗扭强度torsional deflection 扭转；扭转变形tensile strength 拉伸强度yield strength 屈服强度yield point 屈服点yield stress 屈服应力elastic limit 弹性极限ultimate strength 极限强度ultimate tensile stress 极限拉伸应力elasticity 弹性ductility 延展性，可塑（锻）性flexibility 挠性，柔性，易弯性toughness 韧性brittleness 脆性friability 易碎性hardness 硬度rigidity 刚性，稳定性heat treatment 热处理quench 淬火normalising 正火annealing 退火hardening 硬化，淬火tempering 回火casting 铸件，铸造forging 锻件，锻造pickling 酸洗ship timber 船用木材lignumvitae 铁梨木three-plywood 三夹板asbestos 石棉asbestos cloth 石棉布asbestos board 石棉板asbestos sheet 石棉纸asbestos cord 石棉绳asbestos paint 石棉涂料fiberglass 玻璃丝plastics 塑料resin 树脂rubber 橡皮painting 油漆cladding 镀层，表面处理coating 涂层，敷料corrosion 腐蚀，侵蚀wastage 损耗，蚀耗wear and tear 蚀损，磨损fracture 裂纹fatigue fracture 疲劳裂纹hairline fracture 发式裂纹buckling 皱折deformation 变形deflection, deflexion 挠曲flexion 弯曲lamellar tearing 层间撕裂rust 铁锈scale 锈皮pitting 点蚀，锈斑indent 凹痕，凹陷groove 槽沟detachment 脱开，脱焊rupture 断裂，破裂cropping 割掉renewal 换新descale 除锈grind 磨平be veed out 刨除alignment 对准，校直snip 剪断，剪片taper 削斜，斜度B.Shipbuilding workmanship （造船工艺）Working drawing 施工图end elevation 后面图front elevation 正面图side elevation 侧面图plane 平面图lines plan 型线图plan of waterlines 水线图general arrangement plan 总布置图construction plan 结构图damage plan 损坏示意图shell expansion plan 外板展开图docking plan 进坞图framing plan 船体构架图inboard profile plan 纵剖面图midship section plan 舯剖面图loaded waterline plane 满载水线图half breadth plan 半宽水线图stowage plan 配载图laying off lofting 放样mold loft floor 放样台mold loft 放样间template 样板mold loft batten, template batten 木样条evolute 展开线allowance 余量assembly 装配subassembly 分段装配subdivision length 分段长度shipbuilding tolerance 造船公差building berth 船台building dock 干坞slip dock 湿坞marine slipway, railway dry dock 船排marine slipway cradle 船排支架building block, stocks 枕木launch 下水launching ways 下水滑道launching grade 下水坡度launching cradle 下水架end launching 纵向下水side way launching 横向下水hydraulic press 水压机flanging machine 折边机plate bending machine 弯板机angle cutter 角钢切断机planing machine 刨边机shearing machine 剪床guillotine shear 龙门剪床oxy-acetylene welding 氧-乙炔焊co2 gas welding 二氧化碳气体焊arc welding 电弧焊unionmelt welding 埋弧自动焊fusion welding 熔焊fillet welding 角焊flat seam 对接缝butt joint welding 对接焊intermittent welding 间断焊；断续焊staggered intermittent welding 交错断续焊缝lap weld 搭接焊slot weld 槽焊；长孔焊plug weld 塞焊；圆孔焊run of welding 焊道welding torch 焊炬welding rod 焊条flux 焊药filler metal; deposited metal 熔敷金属welding stress 焊接应力welding procedure 焊接方法welding throat 焊喉cutting torch 割炬acetylene generator 乙炔发生器slag 熔渣undercut （焊接）咬边；根切hydraulic test 水压试验pressure test 压力试验flooding test 灌水试验hose test 冲水试验oil tight test 油密试验purchase trial 交船试验四、船舶性能常用英语angle of vanishing stability 稳性消失角buoyancy 浮性buoyancy curve 浮力曲线capsizing lever, upsetting lever 倾覆力臂capsizing moment, upsetting moment 倾覆力矩center of buoyancy 浮心center of floatation 漂心center of gravity 重心curve of areas of waterplanes 水线面积曲线curve of section areas 横剖面面积曲线curve of volumes of displacement 排水量曲线dynamical stability（curve）动稳性（曲线）entrance angle 进水角floodable length 可浸长度force of buoyancy, buoyant force 浮力free surface 自由液面heaving 垂荡heeling angle 横倾角heeling moment 横倾力矩hogging 中拱hogging condition 中拱状态hogging moment(stress) 中拱力矩（应力）hydrostatic curves 静水力曲线initial metacenter 初稳心initial stability 初稳性insubmersibility 抗沉性longitudinal inclination; list; heel 纵倾longitudinal stability 纵稳性panting （波浪对船体的）冲击period of rolling 横摇周期pitching 纵摇pounding 波浪冲击maneuverability 操纵性margin line 限界线metacenter 稳心moment to change trim one centimeter 每厘米纵倾力矩permissible length 许可长度potential head 势头pressure head 压头restoring moment, righting moment 复原力矩restoring lever, righting lever 复原力臂rolling 横摇sagging 中垂sagging condition 中垂状态sagging moment(stress) 中垂力矩（应力）seaworthiness 适航性stability 稳性stability at large angles 大倾角稳性stability criterion numeral 稳性横准数static head 静压头（力）statical stability (curve) 静稳性（曲线）surging 纵荡swaying 横荡tons per centimeter of immersion 每厘米吃水吨数total head (pressure) 总压头（力）transverse inclination, trim 纵倾transverse (longitudinal) metacenter 横（纵）稳心transverse (longitudinal) stability 横（纵）稳性trim by the bow (stern) 首（尾）倾turning quality (circle) 回转性（圈）velocity head 速头weigh curve 重力曲线yawing 艏摇五、船体检验常用英语THE DESCRIPTION OF DAMAGEA.General descriptions1.in good condition 情况良好2.in poor condition 情况欠佳3.in bad condition 情况不佳，情况不良4.in a neglected condition 缺乏保养5.not properly serviced 未经正常保养6.not properly cleaned 未经正常清洁7.not properly protected未经正常保护8.not properly insulated未经正常隔热（或电气绝缘）9.not properly adjusted 未经正常校正10.defective 有缺陷的（失效）11.damaged 损坏damaged beyond repair 损坏了无法修复12.failed (in failure) 失效13.cut of order (in trouble) 故障out of action 停止工作（作用），不是指故障14.in disorder 零乱（船属具零乱了）15.not working 不能工作16.inoperative 不能工作（失效）unworkable, inoperable 指本身不能工作，在损坏状况判断中不能使用17.out of function 不能工作，失去作用，不起作用18.unserviceable (useless) 不能使用（指必须换新的损坏部件）19.could not be started(failed to start) 不能启动20.empty 空的21.fitted incorrectly 安装不正确（指小型的装置设备）installed incorrectly 安装不正确（指较大的装置设备）22.dangerous accumulation of inflammablevapors 可燃气体危险集积it was obvious that this state had existed for a considerable time （损坏）状况是长期存在的23.sluggish in (action, answering) （动作、应答）迟钝B.Deficiencies1.no…fitted, no…provided 未装2.no…available未备有3.missing 遗失4.incomplete 不齐全，不完整5.deficient 不足，缺少6.insufficient 不足7.neglected 遗漏8.omitted 遗漏，省去9.removed 移开，拆走10.washed overboard 冲走11.dropped 跌落12.fitted with wrong ….(size, material, devices…)错用（尺寸，材料，仪器）C.Tightness, stains, loss of etc.1.Leaking 漏2.infiltrating (seeping) 渗漏3.weeping 泪滴4.sweating 汗滴5.not watertight 不水密6.loss of watertightness 失去水密性（比5好）7.loss of airtightness 失去气密性8.loss of oiltightness 失去油密性9.escaping of cool 逃冷10.loss of lub-oil pressure 滑油压力降低11.loss of water pressure 水压力降低12.oil polluted 油污染13.oil soaked 油浸14.water soaked 水浸15.water stained 水渍16.oil stained 油渍17.rust in patches 锈斑18.verdigris in patches 铜绿斑19.water marks 水渍D.Crack, score, break etc.1.scuffed 拉毛（仅从反光上可观察到）2.chafed 擦痕3.scored 拉痕（痕较chafed深）4.scratched 抓痕（硬拉过的痕）5.scraped 刮痕（长期运行刮的痕）6.grooved 槽痕（比pitting深）7.ridged 凸起雷治痕（环状的痕）8.cracked 裂痕hair crack 发痕surface crack 表面裂痕through crack 穿透裂痕non-through crack 未穿透裂痕9.chapped 龟裂，折裂10.fractured 折裂11.broken off 破掉（破裂后跌落）broken 破裂，破碎12.holed 穿洞13.holed & flooded 破洞浸水14.opened 开口15.bent 弯曲16.canted 倾斜17.buckled 皱折18.warped 翘起，翘曲19.indented (dented) 凹痕，凹陷（指船壳板在两档肋位间的凹陷）20.set in 凹陷（指船壳板较大面积的凹陷）21.waved 波曲22.curled 卷曲（指绳索）23.rumpled 褶皱（指垫片）24.bulged 鼓起，凸出25.collapsed 倾陷，倾倒26.ruptured 毁损27.torn off 撕破torn 拉脱28.pierced 刺破29.peeled 剥皮（油漆剥落）30.burst 爆破（指高压管路）31.blown off (packing) 吹脱32.distorted 扭曲，歪扭33.engine break-down 因故障机器突然停车E.Corrosion, seizing, choking etc.1.corrosion 腐蚀2.wasted 耗油3.deteriorated 蚀薄4.thinned 变薄5.pitted 麻点6.eroded 侵蚀7.rusted 生锈8.rotten （木、橡胶）腐烂、腐坏9.decayed （电缆）腐烂、腐坏10. aerated（橡胶、电缆）腐烂、腐坏11. aged 老化12. seized 咬住13. seized by corrosion 锈死14. stuck （粘）咬住15. rust-jammed 锈轧16. fouled 拥塞17. clogged堵塞（常指管子的堵塞）18. blocked 阻塞19. gagged 塞口20. foul & dirty 闭塞21. blanked 封没22. plugged 闭塞23. choked 卡住，阻塞F.Wear, loose, clearance etc.1.Loose 松动2.starting （铆钉）松动3.slack 松动slack back 松出4.worn 磨损5.worn cut evenly 均匀磨损6.worn cut unevenly 不均匀磨损7.worn on one side 单边磨损8.worn out symmetrically 对称磨损9.distorted （轴线弯曲并扭转）扭曲10.sprung （铆钉）扭歪11.twisted （轴线未弯、纯扭转）扭转12.excess clearance 间隙过大13.excess backlash 齿隙过大14.excess vibration 振动过大15.excess noise level 噪音过大16.loose engagement 啮合太松17.loose connection 接头松动18.tooth 齿worn out 磨损chopped off 崩缺fractured 折断19.knocking 敲击knocking cylinder 敲缸knocking valve gear 伐件敲缸knocking bearing 轴承敲缸20.bearing metal 轴承合金detached 脱壳cracked 开裂wiped 铺铅belted 熔化oil groove blocked 油槽堵塞21.out off roundness 失圆22.out off alignment 拉线不直23.off-centering 偏心24.deflected 偏斜G.Burning, heating, etc.1.Sparking 火花2.arcking (arcing) 电弧mutator 整流器scored 拉痕burnt 烧坏worn 磨耗，磨损uneven 不平sparking 火花blackened 发黑rough 粗糙mica undercut 弧坑4.brush set incorrectly 碳刷安装不正确5.scorched 烤焦6.coked 结焦7.charred 结碳8.overheated 过热9.broken down 击穿10. short-circuit 短路11. setting incorrect 整定值不正确12. tripped incorrect 脱扣不正常13. batteriescompletely discharged（电）完全发光undercharged 未充满overcharged 充电过量dry water 水干A. Remove, crop etc.1.Removed 拆下2.removed & replaced 拆装3.removed, faired & replaced拆装拷平4.cropped & renewed 割换（管、板、栏杆）5.partly renewed 部分换新6.partly cropped & renewed 部分割换7.cut off 割除8.faired 拷平9.faired on 原地拷平10.faired in place 原地拷平11.straightened 拷直、校直12.dismantle 拆卸（某一零件）13.disassembled 拆散（解体）14.stripped 拆除（某一部件）15.unshipped 拆下16.disconnected 断开（线、管接头）17.opened 打开18.lifted 抬升、举起19.jacked 顶起（用千斤顶顶起）20.replaced (by, with) 换用21.patch 贴补B.Fit, scrape, grind etc.1.fitted & scraped 拂刮2.fitted & ground 拂磨3.scraped & ground 刮磨4.made to fit 拂合（装配好）5.run to fit 跑合（运动磨合）6.ground round 磨圆7.ground smooth 磨光8.ground & reamed 磨绞9.bored round 镗圆10.planed smooth 刨光11.polished 抛光12.machined 光车13.skimmed 光刀14.finish machined 精加工15.rough machine 粗加工C.Re-metal, adjust, check etc1.Remetalled 重浇白合金2.re-babbitted 重浇白合金（专指巴氏合金）3.pulled out 拉出4.drawn out 抽出5.taken out 取出6.adjusted 调整，校正adjusted for alignment 校正拉线adjusted true 校正拉线adjusted for clearance 校正间隙adjusted for centering 校中adjusted for deflection 校偏7.checked 检查checked for roundness 检查圆度checked for insulation resistance 检查绝缘电阻checked for centering检查中心位置checked for alignment 检查拉线checked for clearance 检查间隙8.cleaned 清洁9.wire-scrubbed 钢丝刷（除锈）10.chipped & scraped 拷锈（油漆）11.measured & recorded 测量并记录12.logged (hourly) 记录（小时）D.weld, rivet, wind etc.1.r epaired by welding 电焊修理2.w elded 补焊、焊接3.c losed up by welds （面积、深度、高度较大）焊补4.b uilt up by welds 堆焊5.p lug welded 塞焊6.s pot welded 点焊7.b utt welded 对接焊8 tackweld 点焊、平头焊、定位焊。

船舶英语词汇dugout 独木舟barge 驳船kayak （爱斯基摩人的）木排outrigger 桨叉架船rowing boat 划艇（美作：rowboat）gondola （意大利的）长平底船whale mother ship 捕鲸母船hydrofoil 水翼船catamarans 双体船dredger 挖泥船boat 船brig, brigantine 双桅船canoe 小船，独木舟caravel 快帆船cargo boat 货船coaster 近海贸易货船cod-fishing boat 捕鳕鱼船whaler 捕鲸船collier 运煤船battleship 战船shallop 小型战船coastguard cutter, coastguard vessel 巡逻艇，缉私艇revenue cutter 缉私船patrol boat 巡逻艇minelayer 布雷艇minesweeper 扫雷艇torpedo boat 鱼雷艇frigate 轻护航舰gunboat 炮舰submarine 潜水艇destroyer 驱逐舰corvette 轻巡洋舰cruiser 巡洋舰aircraft carrier 航空母舰ferry, ferryboat 渡船，渡轮fishing boat 渔船freighter 货船galleon 大型帆船galley 大划桨船hovercraft 气垫船icebreaker 破冰船launch 艇lifeboat 救生艇lighter 驳船liner, ocean liner 远洋班轮merchant ship, merchantman 商船motorboat 摩托艇outboard 尾部装有马达的小艇paddle steamer, paddle boat 明轮船passenger boat 客船piragua, pirogue 独木舟raft 木筏rowing boat 划艇sailing boat, sailing ship 帆船schooner 纵帆船ship 船skiff 小艇sloop 单桅船steamer, steamship 汽轮tanker 油轮trawler 拖网渔船tug, tugboat 拖轮vessel 船yacht 游艇yawl 船载小艇构架结构 Framed structure清洁压载舱Clean ballast tank纵桁结构 Girder structure冷凝水柜Condensate catch tank人孔 manhole干舱 Dry tank饮用水舱 Drinking water tank密封圈 Sealing ring污水舱 Bilge tank铰链 Hinge应急淡水柜Emergency fresh water tank 把手 Handle首舱 Fore tank平衡块 Balance block首尖舱 Fore peak tank斜边舱Hopper side tankwelding焊接液舱 Liquid tank坡口 groove龙骨舱 Keel tank单面坡口 Single groove右舷舱 Starboard tank双面坡口 Double groove顶边水舱 Topside tankⅠ形坡口 Square groove顶边翼舱Topside wing tankV型坡口Single v groove小舱口盖Small hatch coverU型坡口Single u groove水密舱口盖Water-tight small hatch coverX形坡口Single v groove风雨密舱口盖Weather-tight small hatch coverK形坡口 Single bevel grooveY形坡口Single v groove with broad rood face填充金属 Filler metal坡口面 Groove face热影响区 Heat-affected zone(HAZ)坡口角度 Groove angle过热区 Overheated zone焊缝倾角 Weld slope焊合线 Bond line(fusion line)接头根部 Root of joint焊接区 Weld zone根部间隙 Root gap焊缝区Weld metal area钝边 Root face焊缝 weld焊接接头 Welding joint连续焊缝 Continuous weld对接接头 Butt joint断续焊缝 Intermittent weld角接接头 Corner joint纵向焊缝 Longitudinal weldT形接头 T-joint横向焊缝 Transverse weld搭接接头 Lap joint对接焊缝隙 Butt weld十字接头Cross shaped joint角焊缝 Filled weld母材 Base metal(parent metal)并列断续角焊缝Chain intermittent fillet交错断续角焊缝Staggered intermittent fillet弧焊整流器 Arc welding rectifier焊缝正面 Face of weld自动焊 Automatic welding焊缝背面 Back of weld埋弧自动焊Submerged arc welding焊缝宽度 Weld width半自动焊Semi- automatic welding焊缝长度 Weld length氩弧焊 Argon-arc welding焊缝余高 Reinforcement二氧化碳气体保护焊CO2 gas shielded arc welding 焊脚Leg(of a fillet weld)氧乙炔焊 Oxy-acetylene welding焊脚长度 Leg length气割 Gas cutting套管接头 Muff joint碳弧气刨Carbon arc air gouging手工电弧焊Manual arc welding(shielded metal arc welding)水下切割 Underwater cutting直流电弧焊Direct current arc welding等离子弧切割Plasma arc cutting交流电弧焊alternating current arc welding连续焊 Continuous welding弧焊变压器 Arc welding transformer断续焊 Intermittent welding点焊 Sport welding对接焊 Butt welding分段退焊Back step welding角焊 Fillet welding分段多层焊 Block welding搭接焊 Lap welding深溶焊 Deep penetrating welding返修焊 Re-welding跳焊 Skip welding补焊 Repair welding陶质衬垫焊Ceramic backing welding定位焊 Tack welding引弧 Striking the arc封底焊Back sealing welding焊接工艺参数 Welding condition打底焊 Backing welding焊接电流 Welding current堆焊 Surfacing(overlaying)焊接电压 Welding voltage塞焊 Plug welding焊接速度 Welding speed槽焊 Slot welding电弧电压 Arc voltage盖面焊 Consmetic welding焊丝间距 Wire spacing前倾焊 Forward welding空载电压Open circuit voltage后倾焊 Backward welding熔化速度 Melting rate41． 300吨，是船台用起重机，跨度72m。

dugout 独木舟barge 驳船kayak （爱斯基摩人的）木排outrigger 桨叉架船rowing boat 划艇（美作：rowboat）gondola （意大利的）长平底船whale mother ship 捕鲸母船hydrofoil 水翼船catamarans 双体船dredger 挖泥船boat 船brig, brigantine 双桅船canoe 小船，独木舟caravel 快帆船cargo boat 货船coaster 近海贸易货船cod-fishing boat 捕鳕鱼船whaler 捕鲸船collier 运煤船battleship 战船shallop 小型战船coastguard cutter, coastguard vessel 巡逻艇，缉私艇revenue cutter 缉私船patrol boat 巡逻艇minelayer 布雷艇minesweeper 扫雷艇torpedo boat 鱼雷艇frigate 轻护航舰gunboat 炮舰submarine 潜水艇destroyer 驱逐舰corvette 轻巡洋舰cruiser 巡洋舰aircraft carrier 航空母舰ferry, ferryboat 渡船，渡轮fishing boat 渔船freighter 货船galleon 大型帆船galley 大划桨船hovercraft 气垫船icebreaker 破冰船launch 艇lifeboat 救生艇lighter 驳船liner, ocean liner 远洋班轮merchant ship, merchantman 商船motorboat 摩托艇outboard 尾部装有马达的小艇paddle steamer, paddle boat 明轮船passenger boat 客船piragua, pirogue 独木舟raft 木筏rowing boat 划艇sailing boat, sailing ship 帆船schooner 纵帆船ship 船skiff 小艇sloop 单桅船steamer, steamship 汽轮tanker 油轮trawler 拖网渔船tug, tugboat 拖轮vessel 船yacht 游艇yawl 船载小艇。

船的英文怎么读翻译及例句船是重要的水上交通工具，如今航行的速度令人吃惊，最高时速已经可以达到500千米以上了。

今天店铺在这里为大家介绍船的英文怎么读，欢迎大家阅读!船的英文读法vessels英 ['vesəlz]美 ['vesəlz]ship英 [ʃɪp] 美 [ʃɪp]boat英 [bəʊt]美 [boʊt]船的英文例句1. Driving a boat is not the same as driving a car.驾船和开车不是一回事。

2. They had almost reached the boat when a figure shot past them.他们差不多快到船边时，一个人影从他们旁边飞奔而过。

3. He found the binoculars and focused them on the boat.他找到双筒望远镜，然后调焦对准那艘船看。

4. The boat started to spin around in the water.船开始在水中打旋。

5. The boat was anchored off the northern coast of the peninsula.这艘船停泊在离该半岛北部海岸不远的地方。

6. The path serves as an approach to the boat house.这条小路通往船屋。

7. Blake jumped in expertly; the boat dipped slightly under his weight.布莱克很熟练地跳上了船，他的重量使小船微微向下沉了沉。

8. I had to stock the boat up with food.我得在船上备足干粮。

9. It would be just his luck to miss the last boat.他就这运气，误了最后一班船也毫不出奇。

船舶常用英语 船舶类型常用英语liner定期货船tramp ship 不定期货船ship, vessel boat, craft sampan船，船舶艇舢 板 , 小 船 container ship container ship ship集装 箱船 full-全集装箱船 semi-container半集装箱船 multi-purpose containermanpowered boat 人力船ship 多用途集装箱船sailor; sailing boat sailor ship帆船 motor机帆船 power-driven机动船 paddle steamer, paddlegeneral cargo ship/vessel/carrier (cargo) carrier ore carrier杂 货 船 bulk散货船矿砂船wheel vessel 明 轮 船 screw ship; propeller vessel grain carrier 运粮 船 coal螺旋桨船 airscrew ship; aerial propeller vessel 螺旋桨船空气 carrier; coaler carrier运煤船 lumber(timber) 运 木 船 cattle carrierhovercraft; aircushion craft 气垫船 hydrofoil运牲畜船 multi-purpose ship 多用途船水翼船hydrojet propelled boat, water jet boat 喷水船 liquid cargo ship tank 液体货货船 chemical化学品液货船 liquid chemical steamship; steamer 蒸汽机船 motor tanker液 体 化 学 品 船 liquefied gas carriership内燃 机船 diesel ship液化气体船 liquefied petroleum gas tanker (LPG) 液 柴油机船 electrically-propelled ship电力推进船化石油气运输船steam turbine ship 汽轮机船 gas turbineliquefied natural gas tanker (LNG) 液化天然气运输船 ship 核动力船 燃气轮机船 nuclear-power shiptanker; oil tanker tanker 油轮 super超级油轮 VLCC (verydeck ship flush deck ship quarter-deck ship 半舱船 single side ship 甲板船平甲板船 raised尾升高甲板船 well-deck ship单舷长大舱口船 large crude carrier) (吨位在 20 万至 30 万吨之间的)巨型油轮ULCC (ultra-large crude carrier) (吨位在 30 万至 50 万吨之间的) 超巨型油船 three-island ship 三岛式船 doublerefrigerated ship; cold storage ship冷 藏 船 roll- shell ship riveted ship welded shiptransversely framed ship longitudinally framed ship 双壳船铆接船 焊接船横 骨 架 式 船 纵骨架式船 combinedon/roll-off ship (RO/RO ship) ferry ferry 货物渡船 fishing vessel(boat)trawler 滚装船 渡船 passenger旅 客 渡 船 freight ferry渔轮拖网渔轮 barge framed ship 混合 骨 架 式 船 sea-going vesselcarrier; lighter aboard ship(LASH)载驳船海船 ocean-going vesselcoaster ship 远洋船沿海船 channel海峡船 inland waterwaybarge; lighter甲板驳 well-deck barge double shell barge 驳船 deck barge半舱驳双壳驳 single sidevessel 民用船；商船 transport ship yacht 内河船 civil ship; merchant ship运输船 pleasure 游艇 passenger shipbarge 油驳 container barge RO/RO barge gas barge 单 舷 长 大 舱 口 驳 oil barge集装箱驳船 滚装驳船 liquefied液化 气 体 驳 hopper barge客船coasting passenger and cargo ship 沿海客货船开底泥驳 split hopper bargepusher; pushboat ship对开泥驳顶推船；推船 working工程船passenger and auto-car carrier 旅客及汽车运输 tug; tugboat; towboat 拖船 harbor tugcutter suction dredger 绞吸挖泥船bucket winter load line(W) 冬季载重线wheel dredger 斗轮挖泥船bucket dredger winter North Atlantic load line(WNA) 冬季北大西洋链斗挖泥船reclamation craft 吹泥载重线船even keel （首尾）等吃水，平载grab dredger dredger抓斗挖泥船dipper铲斗挖泥船floating pitter;extreme breadthfloatable length最大宽度可浸长度drive pitter 打桩船floating crane; derrick sheer at forward (after) perpendicular 首尾舷弧boat 起重船floating dock sheer line 舷弧线浮船坞cable layer; cable ship scientific surveying ship布缆船科学考察船researchaccommodationaccommodation deck居住舱室起居舱室；旅客甲板ship 科学调查船oceanographic accommodation ladder 舷梯research vessel 海洋调查船accommodation ladder platform 舷梯平台surveying ship ice-breaker 测量船破冰船accommodation ladder manrope 舷梯扶索after body后（部船）体pontoonhigh speed craft 浮舟;浮桥;趸船, 浮码头高速船after peak bulkheadpeak tank艉尖舱舱壁after艉尖舱passenger catamaran vehicle ferry catamaran双体客船双体车辆渡船air holeair pipe空气孔空气管appendagevehicle-passenger ferry catamaran 双体车客渡船（船体水线下的）附体；附件pontoon catamaran二、center line双体趸船船舶结构常用英语中心线，中线auxiliary machinerybalanced rudder压载（物）ballast line系ballast pump辅助机械；辅机平衡舵ballast压载水管压载水泵athwartships 横对船体（与船首尾线直交）ballast pumping system 压载水系统bevel base line amidships斜角；斜面基线在船中部；在纵中线上ballast tank(water)battenbatten-ceiling压载舱（水）板条；压条（封仓用）（货舱内）护舱条，护板designed waterline breadth designed waterline length draftformer/aft draft 设计水线宽设计水线长吃水首/尾吃水beambeam bracket交合线，榫（艏柱或艉柱上）bending moment横梁梁肘板bearding弯矩draft figures intersection吃水尺度交点；交叉；横断面bilgebilge bracket舭部；舱底；（船底）污水沟舭肘板knucklelength between perpendicular折角线垂线间长bilge keel(chock, piece)舭肘板舭龙骨bilge kneelength overallwaterline length 满载水线长总长load bilge linebilge main舭水管系舭水总管register length (breadth; depth) 度）freeboardrise of floor (dead; rise) 登记长度（宽度、深干舷舭高；船底loadlinebilge pipe (suction)bilge pumpstrake(plate)bilge well舭吸水管舭水泵bilge舭列板污水井bittmark 载重水线标记系缆桩bollard 系缆桩；系船柱；双系柱fresh water load line (F.) 淡水载重线bolster 枕垫fresh water timber load line (L.F.) 淡水木材载重线bonnet 烟囱帽；机罩tropical fresh water load line (TF) 热带淡水载重线boom 杆；吊杆；桁；叉架tropical load line (T) 热带载重线boom crutch(support; rest) 吊杆支架summer load line(S) 夏季载重线bossing 尾管突出部；轴包套bottom summer freshwater load line(F) 夏季淡水载重线frame 船底横骨bottomlongitudinal 船底板bowbow fender 船底纵骨bottom plate船首，船头艏护垫coamingcofferdamcollar platecollision bulkhead围板；舱口围板隔离舱封板船首舱壁；防撞舱壁bow flarebow thruster bracket breakwater bridgebulb angle bulbous bowbulb stern bulkhead bulkhead plating bulkhead stiffener bulwarkbulwark plating bulwark stay bunker tank bushingbuttbutt joint(seam) butt rivetingbutt welding butterfly clip bypass valve艏部外飘首侧推器肘板；（三角）拖架挡浪板桥；桥楼；驾驶台圆头角材球形船首，球鼻首球形船尾舱壁舱壁板舱壁扶强材舷墙舷墙板舷墙扶强材燃料舱衬套端接；残片平接缝对接铆对接焊蝴蝶夹旁通阀companion way(hatch)corrugated bulkheadcorrugationcross deck structurecrossing strength membercruiser sterncurtain platecut outdavitdeckdeck beamdeckhousedeck linedeck longitudinaldeck stringer(plate)deep tankderrickdiaphragmdouble bottomdoubling platedrain holeduct keel升降口槽形舱壁皱；槽形；波形舱间甲板结构交叉强力构件巡洋舰型船尾幕板开口；切吊艇架；吊艇柱甲板甲板横梁甲板室甲板线甲板纵骨甲板边板深舱吊杆隔板双层底双层焊合板排水孔箱形龙骨cable stopper camber camber of beam cant beamcant bracket cant frame cantilever capstancargo batten cargo block止链器翘曲梁拱斜梁斜角板斜肋骨悬臂梁绞盘；绞缆机货舱护板吊货滑车dunnagedunnage wooddynamic loadend bracketescape trunkengine bedengine casingescape scuttleescape ventexpansion joint垫舱（物料）；衬垫垫木动载荷端肘板（船内）应急通道机座机舱围壁（船内）应急出口脱险口伸缩接头cargo port 装货舷梯，舷门expansion trunk(tank) （油船）膨胀深井cat walk center girder center strake chafing plate chafing ring chain lock(well) chain pipe chain stopper chockclamp plate cleat （油轮上的）天桥，步桥中底桁中央内底板防擦板防擦环锚链舱锚链管止链器导缆器；垫木夹板，压板羊角；系绳铁栓；防滑条extension bracketface platefenderfender barfair leadflame screenflangeflanged bracketflat keelfloorfolding door延伸肘板面板碰垫；护舷材护舷条导缆器防焰罩折边折边肘板平板龙骨肋板折门forecastle deck fore peak tank艏楼甲板（船的）首舱；前尖舱hopperhopper tank漏斗；开舱泥驳底边舱forward perpendicular 首垂线hopper tank sloping plating 底边舱斜板horizontalfoundation frame 底座肋骨margin platehorizontal girder水平内底板水平桁frame number 肋骨跨数horizontal stiffener 水平扶强材（防挠材）frame space freeing port肋距甲板排水孔；放水孔hullhull construction船壳，船体船体结构gangway (gang ladder or gang board) 舷梯hull plating 船壳板gasket 垫圈，垫料（集）密封垫hull strength 船体强度general service pipe (G.S pump) 通用泵，总用泵inner bottom 内底girdergooseneck(parity iron) gratingground tackle gunwalegunwale angle gunwale bar gunwale railing gunwale tank gussetgutter桁材鹅颈头；吊杆弯头格子板；滑铁板锚泊索具舷缘；舷边舷边角钢舷边角材舷边栏杆舷侧水柜（甲板下）角板；扣板（甲板）水沟；槽沟inner bottom platinginsert platejackjack ladderJacob's ladderJoggled jointjoggling machinekeelkeelblockkeel linekeel plate内底板嵌板；衬板千斤顶绳梯软梯；绳梯折接；弯合折曲机龙骨龙骨墩龙骨线；艏艉线龙骨板gutter angle; waterway angle （舷侧）排水沟角钢keel rail （救生艇）艇底把手gypsy handrail 绞筒（锚机绞车上的）舷墙扶手keelsonkingpost内龙骨起重柱；将军柱hanging rudder; hinged rudder hatch; hatchway; hatch opening hatch bar 吊舵；悬舵舱口封舱压条kneeknee of the decklightening hole肘板；弯头甲板梁肘板减轻孔hatch batten hatch beam (web) hatch booby hatch coaming hatch cover hatch end beam 舱口边压条舱口大梁活动舱口盖舱口板舱口盖舱口端梁lignum vitaelocal strengthlocal stresslongitudinalbulkheadlongitudinal bending铁梨木局部强度局部应力纵骨；纵材；纵桁longitudinal纵舱壁纵向弯曲hatch moulding hatch side girder hatch tarpaulin hatch trunk hawse pipe hawserheel舱口椽材舱口纵桁盖舱布舱口围阱锚链管绳索；大缆踵材；横倾longitudinal framing systemlongitudinal strengthlugmain deckframe人孔man hole doorman hole coaming纵骨架式纵向强度耳板主甲板main主肋骨manhole人孔盖人孔围板moment ofhinged cover(door) holdhold beamhold framehold ladderhold stanchion(pillar) hold stringer 铰链盖（门）货舱舱内梁舱内肋骨舱内梯舱内支柱舱内纵桁inertiamargin platemolded breadthmolded depthmooring holepostmud box惯性矩内底边板型宽型深导缆孔mooring系缆柱；岸柱泥箱non-return valvenon-watertight bulkhead notchoscillating load parallel middle body panel stiffenerpanting arrangement panting beampanting stringer止回阀非水密舱壁切口；槽口；刻痕振动负荷平行中体板格扶强材防挠振结构防挠振梁防挠振纵桁scupperscupper pipescuttleseamsectionmodulusruddershaftshaft bracket排水孔排水管舷窗；人孔（盖）；小舱口盖焊缝；接缝剖面section剖面模数semi-balanced半平衡舵轴轴架pillar 支柱；墩shaft tube; stern tube 艉轴管pintle 舵销shaft tunnel(alley; passage; trunk) 轴隧；地轴弄plane bulkheadplane keelpump roomhelm(rudder) pintle horizontal margin plate plating平台platingplimsoll markpoop平面舱壁平板龙骨泵舱舵销水平内底边板out bottom外底板platform壳板载重线标志艉楼；船尾shedder platesheersheer strakeshellshell frameshell platingshell strake; outside platingshelter deckshifting beam泄板；斜板舷弧；偏航舷顶列板船壳；壳舷侧肋骨船壳板；外板船体外板遮蔽甲板活动舱口梁poop deck 艉楼甲板shifting board (or plank) 止移板（散装谷类）；防动port 舷门；舱门；（装货）口；窗；门；孔板portholepropeller; propellor propeller aperture propeller boss(bub) propeller shaft rackingrailrollinground of beam sternrudderrudder carrier casing舵针；舵栓舷窗；（装货）舷门推进器；螺旋桨螺旋桨空间螺旋桨毂艉轴（船体）横向挠度扶手；栏杆横摇梁拱round圆（船）尾舵舵托rudder舵杆管rudder pintleside girderside longitudinalside platingside strakesingle bottomskidskylightslanting plate污油水舱sloping platesloping plate longitudinalslotsluicesluice valve旁桁材舷侧纵骨舷侧外板舷侧列板单层底护舷木；垫板天窗斜板slop tank斜板斜板纵骨槽；开缝水密门；水闸闸阀rudder plate; rudder blade rudder postrudder stock 舵叶；舵板舵柱舵杆sniped endsoft toesolid floor削斜端软趾实肋板rudder trunk rung scallop scantling舵杆围壁；舵杆管（梯子）踏步；横档扇形开孔构件尺寸sounding pipestabilizerstabilizing tankstaging测量管；测深管减摇装置减摇水舱构架；台架；脚手架scantling of the structure 结构尺寸stanchion 支柱；栏杆柱scarf; scarph scarf joint scarf weld scarfing bracket 嵌接处；斜面；斜接斜（嵌）接（斜面）焊接嵌接肘板static loadstaystay bar(or rod)stay plate静载荷支柱；撑条；支索撑杆撑板stemstem poststernstern counterstern shaft; propeller shaft stern poop 艏；艏柱；艏材艏柱船尾，艉部船尾突出体艉轴艉楼upper (lower) shelf plateupper (lower) stoolventilatorvertical ballast trunkvertical girderwarping chocks上（下）支架板上（下）托架通风筒竖向压载通道竖桁滚轮导缆钳stern post stiffener stool strake尾柱防挠材；扶强材；加固物托架，座，凳列板wash bulkheadwatertight bulkheadwatertight deckweather deck可荡舱壁，挡水舱壁水密舱壁水密门露天甲板strength calculation 强度计算web beam 强横梁，桁板横梁strength deck 强力甲板web frame 加强肋骨，框架肋骨，桁板肋骨stringer stringer plate structural member structural strength strum boxstrutstuffing box superstructure tail (end) shaft tarpaulin纵桁甲板边板构件结构强度（舱底水）过滤箱撑材，支柱，轴架填料箱上层建筑艉轴防水油布，帆布，舱盖布web platewedgewinchwinch-headwindlasswing tankwire clipwire reel三、腹板楔木，楔子起货机绞车卷筒起锚机翼舱，翼柜钢缆夹卷缆车，钢丝滚筒船舶材料及工艺常用英语thrust bearing(block) 推力轴承 A. Shipbuilding material (造船材料)thrust shaft collars tieplatetopside tank推力环带板，牵板，连接板顶边舱；上边柜T-barZ-barI-BarT 型钢Z 型钢工字钢topside tank sloping plating torsion 顶边舱斜板扭转channel barangle steel槽钢角钢torsion strength transom stern transverse扭转强度方形船尾横梁，横材equal angle steelunequal angle steeloffset bulb plate等边角钢不等边角钢球扁钢transverse bulkhead transverse frame横舱壁横肋骨，横框flat plateround steel钢板圆钢transverse framing system 横骨架式half round steel 半圆钢transverse ring transverse strength tripping bracket横环横向强度防倾肘板steel pipealloy steelspecial steel钢管合金钢特种钢tween deck tween deck frame twisting distortion中间甲板甲板间肋骨扭转变形tempering steellow carbon steelhigh tensile steel回火钢材低碳钢高强度钢twisting moment tunnel扭转力矩轴隧，隧道，风筒copperbrass紫铜黄铜tunnel escape tunnel shaft bearing轴隧应急出口中间轴支撑轴承aluminum alloystainless steel铝合金不锈钢ullage pipe (port) 油位测定管（孔）mechanical property 机械性能ullage spaceupper deckupper (reverse) frame 空挡空间上甲板内底横骨tensile testbend testimpact test拉伸试验弯曲试验冲击试验torsion test 扭转试验hairline fracture 发式裂纹torsion strength 抗扭强度buckling 皱折torsional deflection 扭转；扭转变形deformation 变形tensile strength 拉伸强度deflection, deflexion 挠曲yield strength 屈服强度flexion 弯曲yield point 屈服点lamellar tearing 层间撕裂yield stress 屈服应力rust 铁锈elastic limit 弹性极限scale 锈皮ultimate strength 极限强度pitting 点蚀，锈斑ultimate tensile stress 极限拉伸应力indent 凹痕，凹陷elasticity 弹性groove 槽沟ductility 延展性，可塑（锻）性detachment 脱开，脱焊flexibility 挠性，柔性，易弯性rupture 断裂，破裂toughness brittleness friability hardness 韧性脆性易碎性硬度croppingrenewaldescalegrind割掉换新除锈磨平rigidity 刚性，稳定性be veed out 刨除heat treatment 热处理alignment 对准，校直quench 淬火snip 剪断，剪片normalising annealing正火退火taper 削斜，斜度B. Shipbuilding workmanship （造船工艺）hardening tempering casting forging pickling ship timber硬化，淬火回火铸件，铸造锻件，锻造酸洗船用木材Working drawingend elevationfront elevationside elevationplanelines plan施工图后面图正面图侧面图平面图型线图lignumvitae 铁梨木plan of waterlines 水线图three-plywood 三夹板general arrangement plan 总布置图asbestos 石棉construction plan 结构图asbestos cloth 石棉布damage plan 损坏示意图asbestos board 石棉板shell expansion plan 外板展开图asbestos sheet asbestos cord 石棉纸石棉绳docking planframing plan进坞图船体构架图asbestos paint fiberglass石棉涂料玻璃丝inboard profile planmidship section plan纵剖面图舯剖面图plastics 塑料loaded waterline plane 满载水线图resin rubber树脂橡皮half breadth planstowage plan半宽水线图配载图painting 油漆cladding 镀层，表面处理laying off loftingmold loft floor放样放样台coating 涂层，敷料mold loft 放样间corrosion 腐蚀，侵蚀template 样板wastage 损耗，蚀耗mold loft batten, template batten 木样条wear and tear 蚀损，磨损evolute 展开线fracture 裂纹allowance 余量fatigue fracture 疲劳裂纹assembly 装配subassembly 分段装配subdivision length 分段长度pressure testflooding test压力试验灌水试验shipbuilding tolerance 造船公差hose test 冲水试验building berth building dock 船台干坞oil tight testpurchase trial油密试验交船试验slip dock 湿坞marine slipway, railway dry dock 船排四、船舶性能常用英语marine slipway cradle 船排支架angle of vanishing stability 稳性消失角building block, stocks 枕木buoyancy 浮性launch 下水buoyancy curve 浮力曲线launching ways 下水滑道capsizing lever, upsetting lever 倾覆力臂launching grade 下水坡度capsizing moment, upsetting moment 倾覆力矩launching cradle 下水架center of buoyancy 浮心end launching 纵向下水center of floatation 漂心side way launching 横向下水center of gravity 重心hydraulic press 水压机curve of areas of waterplanes 水线面积曲线flanging machine 折边机curve of section areas 横剖面面积曲线plate bending machine 弯板机curve of volumes of displacement 排水量曲线angle cutter 角钢切断机dynamical stability（curve）动稳性（曲线）planing machine shearing machine 刨边机剪床entrance anglefloodable length进水角可浸长度guillotine shear 龙门剪床force of buoyancy, buoyant force 浮力oxy-acetylene welding 氧-乙炔焊free surface 自由液面co 2 gas welding 二氧化碳气体焊heaving 垂荡arc welding 电弧焊heeling angle 横倾角unionmelt welding 埋弧自动焊heeling moment 横倾力矩fusion welding 熔焊hogging 中拱fillet welding 角焊hogging condition 中拱状态flat seam 对接缝hogging moment(stress) 中拱力矩（应力）butt joint welding intermittent welding 对接焊间断焊；断续焊hydrostatic curvesinitial metacenter静水力曲线初稳心staggered intermittent welding 交错断续焊缝initial stability 初稳性lap weld 搭接焊insubmersibility 抗沉性slot weld 槽焊；长孔焊longitudinal inclination; list; heel 纵倾plug weld 塞焊；圆孔焊longitudinal stability 纵稳性run of welding 焊道panting （波浪对船体的）冲击welding torch 焊炬period of rolling 横摇周期welding rod 焊条pitching 纵摇flux 焊药pounding 波浪冲击filler metal; deposited metal 熔敷金属maneuverability 操纵性welding stress welding procedure 焊接应力焊接方法margin linemetacenter限界线稳心welding throat 焊喉moment to change trim one centimeter 每厘米纵倾cutting torch 割炬力矩acetylene generator 乙炔发生器permissible length 许可长度slag 熔渣potential head 势头undercut （焊接）咬边；根切pressure head 压头hydraulic test 水压试验restoring moment, righting moment 复原力矩restoring lever, righting lever 复原力臂unworkable, inoperable 指本身不能工作，rolling 横摇在损坏状况判断中不能使用sagging 中垂17. out of function 不能工作，失去作用，不sagging condition 中垂状态起作用sagging moment(stress) 中垂力矩（应力）18. unserviceable (useless) 不能使用（指必须seaworthiness 适航性换新的损坏部件）stability 稳性19. could not be started(failed to start) 不能stability at large angles 大倾角稳性启动stability criterion numeral 稳性横准数20. empty 空的static head 静压头（力）21. fitted incorrectly 安装不正确（指小型statical stability (curve) 静稳性（曲线）的装置设备）surging swaying 纵荡横荡installed incorrectly的装置设备）安装不正确（指较大tons per centimeter of immersion 每厘米吃水吨数22. dangerous accumulation of inflammable total head (pressure) 总压头（力）vapors 可燃气体危险集积transverse inclination, trim 纵倾it was obvious that this state had existedfor atransverse (longitudinal) metacentertransverse (longitudinal) stability横（纵）稳心横（纵）稳性considerable time期存在的（损坏）状况是长trim by the bow (stern) 首（尾）倾23. sluggish in (action, answering) （动作、应turning quality (circle) 回转性（圈）答）迟钝velocity head 速头 B. Deficienciesweigh curve 重力曲线 1. no…fitted, no…provided 未装yawing 艏摇 2. no…available3. missing 未备有遗失五、船体检验常用英语 4. incomplete 不齐全，不完整THE DESCRIPTION OF DAMAGE A. General descriptions 5. deficient6. insufficient不足，缺少不足1. in good condition2. in poor condition3. in bad condition情况良好情况欠佳情况不佳，情况不良7. neglected8. omitted9. removed遗漏遗漏，省去移开，拆走4. in a neglected condition 缺乏保养10. washed overboard 冲走5. not properly serviced 未经正常保养6. not properly cleaned 未经正常清洁7. not properly protected 未经正常保护11.12.droppedfitted with wrong ….(size, material, devices…)跌落错用（尺8. not properly insulated 未经正常隔热（或电气绝缘）寸，材料，仪器）C. Tightness, stains, loss of etc.9. not properly adjusted 未经正常校正 1. Leaking 漏10.11. defectivedamaged有缺陷的（失效）损坏2. infiltrating (seeping)3. weeping渗漏泪滴damaged beyond repair 损坏了无法修 4. sweating5. not watertight汗滴不水密12.13. failed (in failure)cut of order (in trouble)失效故障6. loss of watertightness7. loss of airtightness失去水密性（比 5 好）失去气密性out of action 停止工作（作用），不是指故8. loss of oiltightness9. escaping of cool 失去油密性逃冷14. in disorder 零乱（船属具零乱了）10. loss of lub-oil pressure 滑油压力降低13.14. oil soakedwater soaked油浸水浸车E. Corrosion, seizing, choking etc.15.16.17.18.19. water stainedoil stainedrust in patchesverdigris in patcheswater marks水渍油渍锈斑铜绿斑水渍1. corrosion2. wasted3. deteriorated4. thinned5. pitted腐蚀耗油蚀薄变薄麻点D. Crack, score, break etc.1. scuffed 拉毛（仅从反光上可观察到）6. eroded7. rusted侵蚀生锈2. chafed3. scored擦痕拉痕（痕较chafed 深）8. rotten9. decayed（木、橡胶）腐烂、腐坏（电缆）腐烂、腐坏4. scratched 抓痕（硬拉过的痕）10. aerated（橡胶、电缆）腐烂、腐坏5. scraped6. grooved7. ridged8. cracked hair crack 刮痕（长期运行刮的痕）槽痕（比pitting 深）凸起雷治痕（环状的痕）裂痕发痕11. aged12. seized13. seized by corrosion14. stuck15. rust-jammed老化咬住锈死（粘）咬住锈轧surface crack 表面裂痕16. fouled 拥塞through crack 穿透裂痕17. clogged 堵塞（常指管子的堵塞）non-through crack 9. chapped 未穿透裂痕龟裂，折裂18. blocked19. gagged阻塞塞口10. fractured 折裂20. foul & dirty 闭塞11. broken off 破掉（破裂后跌落）21. blanked 封没broken 破裂，破碎22. plugged 闭塞12. holed 穿洞23. choked 卡住，阻塞13. holed & flooded 破洞浸水 F. Wear, loose, clearance etc.14.15.16.17.18.19. openedbentcantedbuckledwarpedindented (dented)开口弯曲倾斜皱折翘起，翘曲凹痕，凹陷（指船壳板1. Loose2. starting3. slackslack back4. worn5. worn cut evenly松动（铆钉）松动松动松出磨损均匀磨损在两档肋位间的凹陷） 6. worn cut unevenly 不均匀磨损20.21. set inwaved凹陷（指船壳板较大面积的凹陷）波曲7. worn on one side8. worn out symmetrically单边磨损对称磨损22. curled 卷曲（指绳索）9. distorted （轴线弯曲并扭转）扭曲23. rumpled 褶皱（指垫片）10. sprung （铆钉）扭歪24. bulged 鼓起，凸出11. twisted （轴线未弯、纯扭转）扭转25.26.27.28.29.30. collapsedrupturedtorn offtornpiercedpeeledburst倾陷，倾倒毁损撕破拉脱刺破剥皮（油漆剥落）爆破（指高压管路）12.13.14.15.16.17.18.excess clearanceexcess backlashexcess vibrationexcess noise levelloose engagementloose connectiontooth间隙过大齿隙过大振动过大噪音过大啮合太松接头松动齿31.32.33. blown off (packing)distortedengine break-down吹脱扭曲，歪扭因故障机器突然停worn outchopped offfractured磨损崩缺折断第10 页共12 页19. knockingknocking cylinder敲击敲缸8. faired9. faired on拷平原地拷平knocking valve gear knocking bearing 伐件敲缸轴承敲缸10.11.faired in placestraightened原地拷平拷直、校直20.21.22. bearing metaldetachedcrackedwipedbeltedoil groove blockedout off roundnessout off alignment轴承合金脱壳开裂铺铅熔化油槽堵塞失圆拉线不直12.13.14.15.16.17.18.19.dismantledisassembledstrippedunshippeddisconnectedopenedliftedjacked拆卸（某一零件）拆散（解体）拆除（某一部件）拆下断开（线、管接头）打开抬升、举起顶起（用千斤顶顶起）23.24. off-centeringdeflected偏心偏斜20.21.replaced (by, with)patch换用贴补G. Burning, heating, etc. B. Fit, scrape, grind etc.1. Sparking2. arcking (arcing)3. commutator scoredburntwornuneven sparking blackened roughmica undercut火花电弧整流器拉痕烧坏磨耗，磨损不平火花发黑粗糙弧坑1. fitted & scraped2. fitted & ground3. scraped & ground4. made to fit5. run to fit6. ground round7. ground smooth8. ground & reamed9. bored round10. planed smooth11. polished拂刮拂磨刮磨拂合（装配好）跑合（运动磨合）磨圆磨光磨绞镗圆刨光抛光4. brush set incorrectly 碳刷安装不正确12. machined 光车5. scorched6. coked7. charred8. overheated 烤焦结焦结碳过热13. skimmed14. finish machined15. rough machineC. Re-metal, adjust, check etc光刀精加工粗加工9. broken down10. short-circuit11. setting incorrect12. tripped incorrect击穿短路整定值不正确脱扣不正常1. Remetalled2. re-babbitted合金）3. pulled out重浇白合金重浇白合金（专指巴氏拉出13. batteriescompletely discharged（电）完全发光4. drawn out5. taken out抽出取出underchargedoverchargeddry waterA. Remove, crop etc.1. Removed2. removed & replaced未充满充电过量水干拆下拆装6. adjustedadjusted for alignmentadjusted trueadjusted for clearanceadjusted for centeringadjusted for deflection调整，校正校正拉线校正拉线校正间隙校中校偏3. removed, faired & replaced 拆装拷平7. checked 检查4. cropped & renewed 割换（管、板、栏杆）checked for roundness 检查圆度5. partly renewed 部分换新checked for insulation resistance 检查绝缘6. partly cropped & renewed 部分割换电阻7. cut off 割除第11 页共12 页checked for centering 检查中心位置checked for alignmentchecked for clearance 8. cleaned 检查拉线检查间隙清洁9. wire-scrubbed 钢丝刷（除锈）10. chipped & scraped 拷锈（油漆）11. measured & recorded 测量并记录12. logged (hourly)D. weld, rivet, wind etc.1.repaired by welding2.welded3.closed up by welds大）焊补4.built up by welds5.plug welded6.spot welded7.butt welded记录（小时）电焊修理补焊、焊接（面积、深度、高度较堆焊塞焊点焊对接焊8 tackweld 点焊、平头焊、定位焊第12 页共12 页。

中国海员之家网站航海英语系列船舶常用英语第 1 页“中国海员之家”网站（http://www.seaman­ ）搜集整理，更多航海英语资料请到网站免费下载。

一、船舶类型常用英语ship, vessel 船，船舶boat, craft 艇sampan 舢板 , 小船manpowered boat 人力船sailor;sailing boat 帆船 motorsailor 机帆船power­drivenship 机动船 paddle steamer, paddlewheel vessel 明轮船screw ship;propeller vessel螺旋桨船 airscrew ship; aerial propeller vessel 空气螺旋桨船hovercraft; aircushion craft 气垫船 hydrofoil水翼船hydrojet propelled boat, water jet boat 喷水船steamship;steamer 蒸汽机船 motorship 内燃机船diesel ship柴油机船 electrically­propelled ship 电力推进船steam turbine ship 汽轮机船gas turbineship 燃气轮机船 nuclear­power ship核动力船deck ship 甲板船flush deck ship 平甲板船raisedquarter­deck ship 尾升高甲板船 well­deck ship半舱船single side ship 单舷长大舱口船three­island ship 三岛式船doubleshell ship 双壳船riveted ship 铆接船welded ship 焊接船transversely framed ship 横骨架式船longitudinally framed ship 纵骨架式船 combinedframed ship 混合骨架式船sea­going vessel海船ocean­going vessel 远洋船coaster 沿海船channelship 海峡船inland waterwayvessel 内河船civil ship; merchant ship民用船；商船transport ship 运输船 pleasureyacht 游艇passenger ship客船coasting passenger and cargo ship 沿海客货船passenger and auto­car carrier 旅客及汽车运输船tourist ship; passenger carrier 旅游船cargo ship;freighter 货船cargoliner 定期货船tramp ship 不定期货船container ship 集装箱船full­container ship 全集装箱船 semi­containership 半集装箱船 multi­purpose containership 多用途集装箱船general cargo ship/vessel/carrier 杂货船bulk (cargo) carrier 散货船ore carrier 矿砂船grain carrier 运粮船coalcarrier; coaler 运煤船 lumber(timber)carrier 运木船cattle carrier运牲畜船 multi­purpose ship 多用途船liquid cargo ship 液体货货船 chemicaltank 化学品液货船liquid chemicaltanker 液体化学品船liquefied gas carrier液化气体船liquefied petroleum gas tanker (LPG) 液化石油气运输船liquefied natural gas tanker (LNG) 液化天然气运输船tanker;oil tanker 油轮supertanker 超级油轮 VLCC (verylarge crude carrier) (吨位在20万至30 万吨之间的) 巨型油轮ULCC (ultra­large crude carrier) (吨位在 30 万至 50 万吨之间的) 超巨型油船refrigerated ship;cold storage ship 冷藏船roll-on/roll­off ship (RO/RO ship) 滚装船ferry 渡船 passengerferry 旅客渡船freight ferry货物渡船 fishing vessel(boat) 渔轮trawler 拖网渔轮bargecarrier; lighter aboard ship(LASH)载驳船barge; lighter 驳船 deck barge甲板驳 well­deck barge 半舱驳double shell barge 双壳驳 single sidebarge 单舷长大舱口驳oil barge油驳container barge 集装箱驳船RO/RO barge 滚装驳船liquefiedgas barge 液化气体驳hopper barge开底泥驳 split hopper barge 对开泥驳pusher; pushboat 顶推船；推船 workingship 工程船tug;tugboat; towboat 拖船 harbor tug港作拖船 rescue tug 救助拖轮salvage ship 救捞船 dredger挖泥船trailing suction dredge 耙吸挖泥船第 2 页共12 页cutter suction dredger 绞吸挖泥船bucketwheel dredger 斗轮挖泥船 bucket dredger链斗挖泥船reclamation craft 吹泥船grab dredger 抓斗挖泥船 dipperdredger 铲斗挖泥船floating pitter;drive pitter 打桩船floating crane; derrickboat 起重船floating dock浮船坞 cable layer; cable ship 布缆船scientific surveying ship 科学考察船researchship 科学调查船oceanographicresearch vessel 海洋调查船surveying ship 测量船ice­breaker 破冰船pontoon 浮舟;浮桥;趸船, 浮码头high speed craft 高速船passenger catamaran 双体客船vehicle ferry catamaran 双体车辆渡船vehicle­passenger ferry catamaran 双体车客渡船pontoon catamaran 双体趸船二、船舶结构常用英语center line 中心线，中线athwartships 横对船体（与船首尾线直交）bevel 斜角；斜面base line 基线amidships 在船中部；在纵中线上designed waterline breadth 设计水线宽designed waterline length 设计水线长draft 吃水former/aft draft 首/尾吃水draft figures 吃水尺度intersection 交点；交叉；横断面knuckle 折角线length between perpendicular 垂线间长length overall 总长loadwaterline length 满载水线长register length (breadth; depth) 登记长度（宽度、深度）freeboard 干舷rise of floor (dead; rise) 舭高；船底loadline mark 载重水线标记fresh water load line (F.) 淡水载重线fresh water timber load line (L.F.) 淡水木材载重线tropical fresh water load line (TF) 热带淡水载重线tropical load line (T) 热带载重线summer load line(S) 夏季载重线summer freshwater load line(F) 夏季淡水载重线winter load line(W) 冬季载重线winter North Atlantic load line(WNA) 冬季北大西洋载重线even keel （首尾）等吃水，平载extreme breadth 最大宽度floatable length 可浸长度sheer at forward (after) perpendicular 首尾舷弧sheer line 舷弧线accommodation 居住舱室accommodation deck 起居舱室；旅客甲板accommodation ladder 舷梯accommodation ladder platform 舷梯平台accommodation ladder manrope 舷梯扶索 after body 后（部船）体after peak bulkhead 艉尖舱舱壁afterpeak tank 艉尖舱air hole 空气孔air pipe 空气管appendage（船体水线下的）附体；附件auxiliary machinery 辅助机械；辅机balanced rudder 平衡舵 ballast压载（物）ballast line 压载水管系 ballast pump 压载水泵ballast pumping system 压载水系统ballast tank(water) 压载舱（水）batten 板条；压条（封仓用）batten­ceiling （货舱内）护舱条，护板beam 横梁beam bracket 梁肘板 bearding交合线，榫（艏柱或艉柱上）bending moment 弯矩bilge 舭部；舱底；（船底）污水沟bilge bracket 舭肘板bilge keel(chock, piece) 舭龙骨bilge knee舭肘板bilge line 舭水管系bilge main 舭水总管bilge pipe (suction) 舭吸水管bilge pump 舭水泵bilgestrake(plate) 舭列板bilge well 污水井bitt系缆桩 bollard 系缆桩；系船柱；双系柱bolster 枕垫bonnet 烟囱帽；机罩boom 杆；吊杆；桁；叉架boom crutch(support; rest) 吊杆支架bossing 尾管突出部；轴包套bottom frame 船底横骨bottom第 3 页共12 页longitudinal 船底纵骨bottom plate船底板bow 船首，船头bow fender 艏护垫bow flare 艏部外飘bow thruster 首侧推器bracket 肘板；（三角）拖架breakwater 挡浪板bridge 桥；桥楼；驾驶台bulb angle 圆头角材bulbous bow 球形船首，球鼻首bulb stern 球形船尾bulkhead 舱壁bulkhead plating 舱壁板bulkhead stiffener 舱壁扶强材bulwark 舷墙bulwark plating 舷墙板bulwark stay 舷墙扶强材bunker tank 燃料舱bushing 衬套butt 端接；残片butt joint(seam) 平接缝butt riveting 对接铆butt welding 对接焊butterfly clip 蝴蝶夹bypass valve 旁通阀cable stopper 止链器camber 翘曲camber of beam 梁拱cant beam 斜梁cant bracket 斜角板cant frame 斜肋骨cantilever 悬臂梁capstan 绞盘；绞缆机cargo batten 货舱护板cargo block 吊货滑车cargo port 装货舷梯，舷门cat walk （油轮上的）天桥，步桥center girder 中底桁center strake 中央内底板chafing plate 防擦板chafing ring 防擦环chain lock(well) 锚链舱chain pipe 锚链管chain stopper 止链器chock 导缆器；垫木clamp plate 夹板，压板cleat 羊角；系绳铁栓；防滑条coaming 围板；舱口围板cofferdam 隔离舱collar plate 封板collision bulkhead 船首舱壁；防撞舱壁companion way(hatch) 升降口corrugated bulkhead 槽形舱壁corrugation 皱；槽形；波形cross deck structure 舱间甲板结构crossing strength member 交叉强力构件cruiser stern 巡洋舰型船尾curtain plate 幕板cut out 开口；切davit 吊艇架；吊艇柱deck 甲板deck beam 甲板横梁deckhouse 甲板室deck line 甲板线deck longitudinal 甲板纵骨deck stringer(plate) 甲板边板deep tank 深舱derrick 吊杆diaphragm 隔板double bottom 双层底doubling plate 双层焊合板drain hole 排水孔duct keel 箱形龙骨dunnage 垫舱（物料）；衬垫dunnage wood 垫木dynamic load 动载荷end bracket 端肘板escape trunk （船内）应急通道engine bed 机座engine casing 机舱围壁escape scuttle （船内）应急出口escape vent 脱险口expansion joint 伸缩接头expansion trunk(tank) （油船）膨胀深井extension bracket 延伸肘板face plate 面板fender 碰垫；护舷材fender bar 护舷条fair lead 导缆器flame screen 防焰罩flange 折边flanged bracket 折边肘板flat keel 平板龙骨floor 肋板folding door 折门第 4 页共12 页forecastle deck 艏楼甲板fore peak tank （船的）首舱；前尖舱forward perpendicular 首垂线foundation 底座frame 肋骨frame number 肋骨跨数frame space 肋距freeing port 甲板排水孔；放水孔gangway (gang ladder or gang board) 舷梯gasket 垫圈，垫料（集）密封垫general service pipe (G.S pump) 通用泵，总用泵girder 桁材gooseneck(parity iron) 鹅颈头；吊杆弯头grating 格子板；滑铁板ground tackle 锚泊索具gunwale 舷缘；舷边gunwale angle 舷边角钢gunwale bar 舷边角材gunwale railing 舷边栏杆gunwale tank 舷侧水柜（甲板下）gusset 角板；扣板gutter （甲板）水沟；槽沟gutter angle; waterway angle （舷侧）排水沟角钢gypsy 绞筒（锚机绞车上的）handrail 舷墙扶手hanging rudder; hinged rudder 吊舵；悬舵hatch;hatchway; hatch opening 舱口hatch bar 封舱压条hatch batten 舱口边压条hatch beam (web) 舱口大梁hatch booby 活动舱口盖hatch coaming 舱口板hatch cover 舱口盖hatch end beam 舱口端梁hatch moulding 舱口椽材hatch side girder 舱口纵桁hatch tarpaulin 盖舱布hatch trunk 舱口围阱hawse pipe 锚链管hawser 绳索；大缆heel 踵材；横倾hinged cover(door) 铰链盖（门）hold 货舱hold beam 舱内梁hold frame 舱内肋骨hold ladder 舱内梯hold stanchion(pillar) 舱内支柱hold stringer 舱内纵桁hopper 漏斗；开舱泥驳hopper tank 底边舱hopper tank sloping plating 底边舱斜板 horizontal margin plate 水平内底板horizontal girder 水平桁horizontal stiffener 水平扶强材（防挠材）hull 船壳，船体hull construction 船体结构hull plating 船壳板hull strength 船体强度inner bottom 内底inner bottom plating 内底板insert plate 嵌板；衬板jack 千斤顶jack ladder 绳梯Jacob's ladder 软梯；绳梯Joggled joint 折接；弯合joggling machine 折曲机keel 龙骨keelblock 龙骨墩keel line 龙骨线；艏艉线keel plate 龙骨板keel rail （救生艇）艇底把手keelson 内龙骨kingpost 起重柱；将军柱knee 肘板；弯头knee of the deck 甲板梁肘板lightening hole 减轻孔lignum vitae 铁梨木local strength 局部强度local stress 局部应力longitudinal 纵骨；纵材；纵桁 longitudinal bulkhead 纵舱壁longitudinal bending 纵向弯曲longitudinal framing system 纵骨架式longitudinal strength 纵向强度lug 耳板main deck 主甲板 mainframe 主肋骨 manhole人孔 man hole door 人孔盖man hole coaming 人孔围板moment ofinertia 惯性矩margin plate 内底边板molded breadth 型宽molded depth 型深mooring hole 导缆孔 mooringpost 系缆柱；岸柱mud box 泥箱第 5 页共12 页non­return valve 止回阀non­watertight bulkhead 非水密舱壁notch 切口；槽口；刻痕oscillating load 振动负荷parallel middle body 平行中体panel stiffener 板格扶强材panting arrangement 防挠振结构panting beam 防挠振梁panting stringer 防挠振纵桁pillar 支柱；墩pintle 舵销plane bulkhead 平面舱壁plane keel 平板龙骨pump room 泵舱helm(rudder) pintle 舵销horizontal margin plate 水平内底边板 out bottomplating 外底板platform平台 plating 壳板plimsoll mark 载重线标志poop 艉楼；船尾poop deck 艉楼甲板port 舷门；舱门；（装货）口；窗；门；孔porthole 舷窗；（装货）舷门propeller; propellor 推进器；螺旋桨propeller aperture 螺旋桨空间propeller boss(bub) 螺旋桨毂propeller shaft 艉轴racking （船体）横向挠度rail 扶手；栏杆rolling 横摇round of beam 梁拱roundstern 圆（船）尾rudder 舵rudder carrier 舵托ruddercasing 舵杆管rudder pintle舵针；舵栓rudder plate; rudder blade 舵叶；舵板rudder post 舵柱rudder stock 舵杆rudder trunk 舵杆围壁；舵杆管rung （梯子）踏步；横档scallop 扇形开孔scantling 构件尺寸scantling of the structure 结构尺寸scarf; scarph 嵌接处；斜面；斜接scarf joint 斜（嵌）接scarf weld （斜面）焊接scarfing bracket 嵌接肘板scupper 排水孔scupper pipe 排水管scuttle 舷窗；人孔（盖）；小舱口盖seam 焊缝；接缝section 剖面sectionmodulus 剖面模数semi­balancedrudder 半平衡舵shaft 轴shaft bracket 轴架shaft tube; stern tube 艉轴管shaft tunnel(all ey;passage; trunk) 轴隧；地轴弄shedder plate 泄板；斜板sheer 舷弧；偏航sheer strake 舷顶列板shell 船壳；壳shell frame 舷侧肋骨shell plating 船壳板；外板shell strake; outside plating 船体外板shelter deck 遮蔽甲板shifting beam 活动舱口梁shifting board (or plank) 止移板（散装谷类）；防动板side girder 旁桁材side longitudinal 舷侧纵骨side plating 舷侧外板side strake 舷侧列板single bottom 单层底skid 护舷木；垫板skylight 天窗slanting plate 斜板 slop tank污油水舱sloping plate 斜板sloping plate longitudinal 斜板纵骨slot 槽；开缝sluice 水密门；水闸sluice valve 闸阀sniped end 削斜端soft toe 软趾solid floor 实肋板sounding pipe 测量管；测深管stabilizer 减摇装置stabilizing tank 减摇水舱staging 构架；台架；脚手架stanchion 支柱；栏杆柱static load 静载荷stay 支柱；撑条；支索stay bar(or rod) 撑杆stay plate 撑板第 6 页共12 页stem 艏；艏柱；艏材stem post 艏柱stern 船尾，艉部stern counter 船尾突出体stern shaft; propeller shaft 艉轴stern poop 艉楼stern post 尾柱stiffener 防挠材；扶强材；加固物stool 托架，座，凳strake 列板strength calculation 强度计算strength deck 强力甲板stringer 纵桁stringer plate 甲板边板structural member 构件structural strength 结构强度strum box （舱底水）过滤箱strut 撑材，支柱，轴架stuffing box 填料箱superstructure 上层建筑tail (end) shaft 艉轴tarpaulin 防水油布，帆布，舱盖布thrust bearing(block) 推力轴承thrust shaft collars 推力环tieplate 带板，牵板，连接板topside tank 顶边舱；上边柜topside tank sloping plating 顶边舱斜板torsion 扭转torsion strength 扭转强度transom stern 方形船尾transverse 横梁，横材transverse bulkhead 横舱壁transverse frame 横肋骨，横框transverse framing system 横骨架式transverse ring 横环transverse strength 横向强度tripping bracket 防倾肘板tween deck 中间甲板tween deck frame 甲板间肋骨twisting distortion 扭转变形twisting moment 扭转力矩tunnel 轴隧，隧道，风筒tunnel escape 轴隧应急出口tunnel shaft bearing 中间轴支撑轴承ullage pipe (port) 油位测定管（孔）ullage space 空挡空间upper deck 上甲板upper (reverse) frame 内底横骨upper (lower) shelf plate 上（下）支架板upper (lower) stool 上（下）托架ventilator 通风筒vertical ballast trunk 竖向压载通道vertical girder 竖桁warping chocks 滚轮导缆钳wash bulkhead 可荡舱壁，挡水舱壁watertight bulkhead 水密舱壁watertight deck 水密门weather deck 露天甲板web beam 强横梁，桁板横梁web frame 加强肋骨，框架肋骨，桁板肋骨web plate 腹板wedge 楔木，楔子winch 起货机winch­head 绞车卷筒windlass 起锚机wing tank 翼舱，翼柜wire clip 钢缆夹wire reel 卷缆车，钢丝滚筒三、船舶材料及工艺常用英语A. Shipbuilding material (造船材料)T­bar T 型钢Z­bar Z 型钢I­Bar 工字钢channel bar 槽钢angle steel 角钢equal angle steel 等边角钢unequal angle steel 不等边角钢offset bulb plate 球扁钢flat plate 钢板round steel 圆钢half round steel 半圆钢steel pipe 钢管alloy steel 合金钢special steel 特种钢tempering steel 回火钢材low carbon steel 低碳钢high tensile steel 高强度钢copper 紫铜brass 黄铜aluminum alloy 铝合金stainless steel 不锈钢mechanical property 机械性能tensile test 拉伸试验bend test 弯曲试验impact test 冲击试验第7 页共12 页torsion test 扭转试验torsion strength 抗扭强度torsional deflection 扭转；扭转变形tensile strength 拉伸强度yield strength 屈服强度yield point 屈服点yield stress 屈服应力elastic limit 弹性极限ultimate strength 极限强度ultimate tensile stress 极限拉伸应力elasticity 弹性ductility 延展性，可塑（锻）性flexibility 挠性，柔性，易弯性toughness 韧性brittleness 脆性friability 易碎性hardness 硬度rigidity 刚性，稳定性heat treatment 热处理quench 淬火normalising 正火annealing 退火hardening 硬化，淬火tempering 回火casting 铸件，铸造forging 锻件，锻造pickling 酸洗ship timber 船用木材lignumvitae 铁梨木three­plywood 三夹板asbestos 石棉asbestos cloth 石棉布asbestos board 石棉板asbestos sheet 石棉纸asbestos cord 石棉绳asbestos paint 石棉涂料fiberglass 玻璃丝plastics 塑料resin 树脂rubber 橡皮painting 油漆cladding 镀层，表面处理coating 涂层，敷料corrosion 腐蚀，侵蚀wastage 损耗，蚀耗wear and tear 蚀损，磨损fracture 裂纹fatigue fracture 疲劳裂纹hairline fracture 发式裂纹buckling 皱折deformation 变形deflection, deflexion 挠曲flexion 弯曲lamellar tearing 层间撕裂rust 铁锈scale 锈皮pitting 点蚀，锈斑indent 凹痕，凹陷groove 槽沟detachment 脱开，脱焊rupture 断裂，破裂cropping 割掉renewal 换新descale 除锈grind 磨平be veed out 刨除alignment 对准，校直snip 剪断，剪片taper 削斜，斜度B. Shipbuilding workmanship （造船工艺）Working drawing 施工图end elevation 后面图front elevation 正面图side elevation 侧面图plane 平面图lines plan 型线图plan of waterlines 水线图general arrangement plan 总布置图construction plan 结构图damage plan 损坏示意图shell expansion plan 外板展开图docking plan 进坞图framing plan 船体构架图inboard profile plan 纵剖面图midship section plan 舯剖面图loaded waterline plane 满载水线图half breadth plan 半宽水线图stowage plan 配载图laying off lofting 放样mold loft floor 放样台mold loft 放样间template 样板mold loft batten, template batten 木样条evolute 展开线allowance 余量assembly 装配第8 页共12 页subassembly 分段装配subdivision length 分段长度shipbuilding tolerance 造船公差building berth 船台building dock 干坞slip dock 湿坞marine slipway, railway dry dock 船排marine slipway cradle 船排支架building block, stocks 枕木launch 下水launching ways 下水滑道launching grade 下水坡度launching cradle 下水架end launching 纵向下水side way launching 横向下水hydraulic press 水压机flanging machine 折边机plate bending machine 弯板机angle cutter 角钢切断机planing machine 刨边机shearing machine 剪床guillotine shear 龙门剪床oxy­acetylene welding 氧­乙炔焊co 2gas welding 二氧化碳气体焊arc welding 电弧焊unionmelt welding 埋弧自动焊fusion welding 熔焊fillet welding 角焊flat seam 对接缝butt joint welding 对接焊intermittent welding 间断焊；断续焊staggered intermittent welding 交错断续焊缝lap weld 搭接焊slot weld 槽焊；长孔焊plug weld 塞焊；圆孔焊run of welding 焊道welding torch 焊炬welding rod 焊条flux 焊药filler metal; deposited metal 熔敷金属welding stress 焊接应力welding procedure 焊接方法welding throat 焊喉cutting torch 割炬acetylene generator 乙炔发生器slag 熔渣undercut （焊接）咬边；根切hydraulic test 水压试验pressure test 压力试验flooding test 灌水试验hose test 冲水试验oil tight test 油密试验purchase trial 交船试验四、船舶性能常用英语angle of vanishing stability 稳性消失角buoyancy 浮性buoyancy curve 浮力曲线capsizing lever, upsetting lever 倾覆力臂capsizing moment, upsetting moment 倾覆力矩center of buoyancy 浮心center of floatation 漂心center of gravity 重心curve of areas of waterplanes 水线面积曲线curve of section areas 横剖面面积曲线curve of volumes of displacement 排水量曲线dynamical stability（curve）动稳性（曲线）entrance angle 进水角floodable length 可浸长度force of buoyancy, buoyant force 浮力free surface 自由液面heaving 垂荡heeling angle 横倾角heeling moment 横倾力矩hogging 中拱hogging condition 中拱状态hogging moment(stress) 中拱力矩（应力）hydrostatic curves 静水力曲线initial metacenter 初稳心initial stability 初稳性insubmersibility 抗沉性longitudinal inclination;list; heel 纵倾longitudinal stability 纵稳性panting （波浪对船体的）冲击period of rolling 横摇周期pitching 纵摇pounding 波浪冲击maneuverability 操纵性margin line 限界线metacenter 稳心moment to change trim one centimeter 每厘米纵倾力矩permissible length 许可长度potential head 势头pressure head 压头restoring moment, righting moment 复原力矩第9 页共12 页restoring lever, righting lever 复原力臂rolling 横摇sagging 中垂sagging condition 中垂状态sagging moment(stress) 中垂力矩（应力）seaworthiness 适航性stability 稳性stability at large angles 大倾角稳性stability criterion numeral 稳性横准数static head 静压头（力）statical stability (curve) 静稳性（曲线）surging 纵荡swaying 横荡tons per centimeter of immersion 每厘米吃水吨数total head (pressure) 总压头（力）transverse inclination, trim 纵倾transverse (longitudinal) metacenter 横（纵）稳心transverse (longitudinal) stability 横（纵）稳性trim by the bow (stern) 首（尾）倾turning quality (circle) 回转性（圈）velocity head 速头weigh curve 重力曲线yawing 艏摇五、船体检验常用英语THE DESCRIPTION OF DAMAGEA. General descriptions1. in good condition 情况良好2. in poor condition 情况欠佳3. in bad condition 情况不佳，情况不良4. in a neglected condition 缺乏保养5. not properly serviced 未经正常保养6. not properly cleaned 未经正常清洁7. not properly protected 未经正常保护8. not properly insulated 未经正常隔热（或电气绝缘）9. not properly adjusted 未经正常校正10. defective 有缺陷的（失效）11. damaged 损坏damaged beyond repair 损坏了无法修复12. failed (in failure) 失效13. cut of order (in trouble) 故障out of action 停止工作（作用），不是指故障14. in disorder 零乱（船属具零乱了）15. not working 不能工作16. inoperative 不能工作（失效）unworkable, inoperable 指本身不能工作，在损坏状况判断中不能使用17. out of function 不能工作，失去作用，不起作用18. unserviceable (useless) 不能使用（指必须换新的损坏部件）19. could not be started(failed to start) 不能启动20. empty 空的21. fitted incorrectly 安装不正确（指小型的装置设备）installed incorrectly 安装不正确（指较大的装置设备）22. dangerous accumulation of inflammable vapors 可燃气体危险集积it was obvious that this state had existed for a considerable time （损坏）状况是长期存在的23. sluggish in (action, answering) （动作、应答）迟钝B. Deficiencies1. no…fitted, no…provided 未装2. no…available 未备有3. missing 遗失4. incomplete 不齐全，不完整5. deficient 不足，缺少6. insufficient 不足7. neglected 遗漏8. omitted 遗漏，省去9. removed 移开，拆走10. washed overboard 冲走11. dropped 跌落12. fitted with wrong ….(size, material, devices…) 错用（尺寸，材料，仪器）C. Tightness, stains, loss of etc.1. Leaking 漏2. infiltrating (seeping) 渗漏3. weeping 泪滴4. sweating 汗滴5. not watertight 不水密6. loss of watertightness 失去水密性（比 5 好）7. loss of airtightness 失去气密性8. loss of oiltightness 失去油密性9. escaping of cool 逃冷10. loss of lub­oil pressure 滑油压力降低11. loss of water pressure 水压力降低12. oil polluted 油污染第10 页共12 页13. oil soaked 油浸14. water soaked 水浸15. water stained 水渍16. oil stained 油渍17. rust in patches 锈斑18. verdigris in patches 铜绿斑19. water marks 水渍D. Crack, score, break etc.1. scuffed 拉毛（仅从反光上可观察到）2. chafed 擦痕3. scored 拉痕（痕较 chafed 深）4. scratched 抓痕（硬拉过的痕）5. scraped 刮痕（长期运行刮的痕）6. grooved 槽痕（比 pitting深）7. ridged 凸起雷治痕（环状的痕）8. cracked 裂痕hair crack 发痕surface crack 表面裂痕through crack 穿透裂痕non­through crack 未穿透裂痕9. chapped 龟裂，折裂10. fractured 折裂11. broken off 破掉（破裂后跌落）broken 破裂，破碎12. holed 穿洞13. holed & flooded 破洞浸水14. opened 开口15. bent 弯曲16. canted 倾斜17. buckled 皱折18. warped 翘起，翘曲19. indented (dented) 凹痕，凹陷（指船壳板在两档肋位间的凹陷）20. set in 凹陷（指船壳板较大面积的凹陷）21. waved 波曲22. curled 卷曲（指绳索）23. rumpled 褶皱（指垫片）24. bulged 鼓起，凸出25. collapsed 倾陷，倾倒26. ruptured 毁损27. torn off 撕破torn 拉脱28. pierced 刺破29. peeled 剥皮（油漆剥落）30. burst 爆破（指高压管路）31. blown off (packing) 吹脱32. distorted 扭曲，歪扭33. engine break­down 因故障机器突然停车E. Corrosion, seizing, choking etc.1. corrosion 腐蚀2. wasted 耗油3. deteriorated 蚀薄4. thinned 变薄5. pitted 麻点6. eroded 侵蚀7. rusted 生锈8. rotten （木、橡胶）腐烂、腐坏9. decayed （电缆）腐烂、腐坏10. aerated（橡胶、电缆）腐烂、腐坏11. aged 老化12. seized 咬住13. seized by corrosion 锈死14. stuck （粘）咬住15. rust­jammed 锈轧16. fouled 拥塞17. clogged 堵塞（常指管子的堵塞）18. blocked 阻塞19. gagged 塞口20. foul & dirty 闭塞21. blanked 封没22. plugged 闭塞23. choked 卡住，阻塞F. Wear, loose, clearance etc.1. Loose 松动2. starting （铆钉）松动3. slack 松动slack back 松出4. worn 磨损5. worn cut evenly 均匀磨损6. worn cut unevenly 不均匀磨损7. worn on one side 单边磨损8. worn out symmetrically 对称磨损9. distorted （轴线弯曲并扭转）扭曲10. sprung （铆钉）扭歪11. twisted （轴线未弯、纯扭转）扭转12. excess clearance 间隙过大13. excess backlash 齿隙过大14. excess vibration 振动过大15. excess noise level 噪音过大16. loose engagement 啮合太松17. loose connection 接头松动18. tooth 齿worn out 磨损chopped off 崩缺fractured 折断第11 页共12 页19. knocking 敲击knocking cylinder 敲缸knocking valve gear 伐件敲缸knocking bearing 轴承敲缸20. bearing metal 轴承合金detached 脱壳cracked 开裂wiped 铺铅belted 熔化oil groove blocked 油槽堵塞21. out off roundness 失圆22. out off alignment 拉线不直23. off­centering 偏心24. deflected 偏斜G. Burning, heating, etc.1. Sparking 火花2. arcking (arcing) 电弧3. commutator 整流器scored 拉痕burnt 烧坏worn 磨耗，磨损uneven 不平sparking 火花blackened 发黑rough 粗糙mica undercut 弧坑4. brush set incorrectly 碳刷安装不正确5. scorched 烤焦6. coked 结焦7. charred 结碳8. overheated 过热9. broken down 击穿10. short­circuit 短路11. setting incorrect 整定值不正确12. tripped incorrect 脱扣不正常13. batteriescompletely discharged（电）完全发光undercharged 未充满overcharged 充电过量dry water 水干A. Remove, crop etc.1. Removed 拆下2. removed & replaced 拆装3. removed, faired & replaced 拆装拷平4. cropped & renewed 割换（管、板、栏杆）5. partly renewed 部分换新6. partly cropped & renewed 部分割换7. cut off 割除8. faired 拷平9. faired on 原地拷平10. faired in place 原地拷平11. straightened 拷直、校直12. dismantle 拆卸（某一零件）13. disassembled 拆散（解体）14. stripped 拆除（某一部件）15. unshipped 拆下16. disconnected 断开（线、管接头）17. opened 打开18. lifted 抬升、举起19. jacked 顶起（用千斤顶顶起）20. replaced (by, with) 换用21. patch 贴补B. Fit, scrape, grind etc.1. fitted & scraped 拂刮2. fitted & ground 拂磨3. scraped & ground 刮磨4. made to fit 拂合（装配好）5. run to fit 跑合（运动磨合）6. ground round 磨圆7. ground smooth 磨光8. ground & reamed 磨绞9. bored round 镗圆10. planed smooth 刨光11. polished 抛光12. machined 光车13. skimmed 光刀14. finish machined 精加工15. rough machine 粗加工C. Re-metal, adjust, check etc1. Remetalled 重浇白合金2. re­babbitted 重浇白合金（专指巴氏合金）3. pulled out 拉出4. drawn out 抽出5. taken out 取出6. adjusted 调整，校正adjusted for alignment 校正拉线adjusted true 校正拉线adjusted for clearance 校正间隙adjusted for centering 校中adjusted for deflection 校偏7. checked 检查checked for roundness 检查圆度checked for insulation resistance 检查绝缘电阻checked for centering 检查中心位置第12 页共12 页checked for alignment 检查拉线checked for clearance 检查间隙8. cleaned 清洁9. wire­scrubbed 钢丝刷（除锈）10. chipped & scraped 拷锈（油漆）11. measured & recorded 测量并记录12. logged (hourly) 记录（小时）D. weld, rivet, wind etc.1.repaired by welding 电焊修理2.welded 补焊、焊接3.closed up by welds （面积、深度、高度较大）焊补4.built up by welds 堆焊5.plug welded 塞焊6.spot welded 点焊7.butt welded 对接焊8 tackweld 点焊、平头焊、定位焊。

一、船舶类型常用英语ship, vessel 船，船舶boat, craft 艇sampan 舢板, 小船manpowered boat 人力船sailor; sailing boat 帆船motor sailor 机帆船power-driven ship 机动船paddle steamer, paddle wheel vessel 明轮船screw ship; propeller vessel 螺旋桨船airscrew ship; aerial propeller vessel 空气螺旋桨船hovercraft; aircushion craft 气垫船hydrofoil 水翼船hydrojet propelled boat, water jet boat 喷水船steamship; steamer 蒸汽机船motor ship 内燃机船diesel ship 柴油机船electrically-propelled ship 电力推进船steam turbine ship 汽轮机船gas turbine ship 燃气轮机船nuclear-power ship 核动力船deck ship 甲板船flush deck ship 平甲板船raised quarter-deck ship 尾升高甲板船well-deck ship 半舱船single side ship 单舷长大舱口船three-island ship 三岛式船double shell ship 双壳船riveted ship 铆接船welded ship 焊接船transversely framed ship 横骨架式船longitudinally framed ship 纵骨架式船combined framed ship 混合骨架式船sea-going vessel 海船ocean-going vessel 远洋船coaster 沿海船channel ship 海峡船inland waterway vessel 内河船civil ship; merchant ship 民用船；商船transport ship 运输船pleasure yacht 游艇passenger ship 客船coasting passenger and cargo ship沿海客货船passenger and auto-car carrier 旅客及汽车运输船tourist ship; passenger carrier 旅游船第 1 页共24 页cargo ship; freighter 货船cargo liner 定期货船tramp ship 不定期货船container ship 集装箱船full-container ship 全集装箱船semi-container ship 半集装箱船multi-purpose container ship 多用途集装箱船general cargo ship/vessel/carrier 杂货船bulk (cargo) carrier 散货船ore carrier 矿砂船grain carrier 运粮船coal carrier; coaler 运煤船lumber(timber) carrier 运木船cattle carrier 运牲畜船multi-purpose ship 多用途船liquid cargo ship 液体货货船chemical tank 化学品液货船liquid chemical tanker 液体化学品船liquefied gas carrier 液化气体船liquefied petroleum gas tanker (LPG) 液化石油气运输船liquefied natural gas tanker (LNG) 液化天然气运输船tanker; oil tanker 油轮super tanker 超级油轮VLCC (very large crude carrier) (吨位在20万至30 万吨之间的) 巨型油轮ULCC (ultra-large crude carrier) (吨位在30万至50万吨之间的) 超巨型油船refrigerated ship; cold storage ship 冷藏船roll-on/roll-off ship (RO/RO ship) 滚装船ferry 渡船passenger ferry 旅客渡船freight ferry 货物渡船fishing vessel(boat) 渔轮trawler 拖网渔轮barge carrier; lighter aboard ship(LASH)载驳船barge; lighter 驳船deck barge 甲板驳well-deck barge 半舱驳double shell barge 双壳驳single side barge 单舷长大舱口驳oil barge 油驳container barge 集装箱驳船RO/RO barge 滚装驳船liquefied gas barge 液化气体驳. 专业.专注.hopper barge 开底泥驳split hopper barge 对开泥驳pusher; pushboat 顶推船；推船working ship 工程船tug; tugboat; towboat 拖船harbor tug 港作拖船rescue tug 救助拖轮salvage ship 救捞船dredger 挖泥船trailing suction dredge 耙吸挖泥船cutter suction dredger 绞吸挖泥船bucket wheel dredger 斗轮挖泥船bucket dredger 链斗挖泥船reclamation craft 吹泥船grab dredger 抓斗挖泥船dipper dredger 铲斗挖泥船floating pitter; drive pitter 打桩船floating crane; derrick boat 起重船floating dock 浮船坞cable layer; cable ship 布缆船scientific surveying ship 科学考察船research ship 科学调查船oceanographic research vessel 海洋调查船surveying ship 测量船ice-breaker 破冰船pontoon 浮舟; 浮桥; 趸船, 浮码头high speed craft 高速船passenger catamaran 双体客船vehicle ferry catamaran 双体车辆渡船vehicle-passenger ferry catamaran 双体车客渡船pontoon catamaran 双体趸船二、船舶结构常用英语center line 中心线，中线athwartships 横对船体（与船首尾线直交）bevel 斜角；斜面base line 基线amidships 在船中部；在纵中线上designed waterline breadth 设计水线宽designed waterline length 设计水线长draft 吃水former/aft draft 首/尾吃水draft figures 吃水尺度intersection 交点；交叉；横断面knuckle 折角线length between perpendicular 垂线间长. 专业.专注.length overall 总长load waterline length 满载水线长register length (breadth; depth) 登记长度（宽度、深度）freeboard 干舷rise of floor (dead; rise) 舭高；船底loadline mark 载重水线标记fresh water load line (F.) 淡水载重线fresh water timber load line (L.F.) 淡水木材载重线tropical fresh water load line (TF) 热带淡水载重线tropical load line (T) 热带载重线summer load line(S) 夏季载重线summer freshwater load line(F) 夏季淡水载重线winter load line(W) 冬季载重线winter North Atlantic load line(WNA) 冬季北大西洋载重线even keel （首尾）等吃水，平载extreme breadth 最大宽度floatable length 可浸长度sheer at forward (after) perpendicular 首尾舷弧sheer line 舷弧线accommodation 居住舱室accommodation deck 起居舱室；旅客甲板accommodation ladder 舷梯accommodation ladder platform 舷梯平台accommodation ladder manrope 舷梯扶索after body 后（部船）体after peak bulkhead 艉尖舱舱壁after peak tank 艉尖舱air hole 空气孔air pipe 空气管appendage （船体水线下的）附体；附件auxiliary machinery 辅助机械；辅机balanced rudder 平衡舵ballast 压载（物）ballast line 压载水管系ballast pump 压载水泵ballast pumping system 压载水系统ballast tank(water) 压载舱（水）batten 板条；压条（封仓用）batten-ceiling （货舱内）护舱条，护板beam 横梁beam bracket 梁肘板bearding 交合线，榫（艏柱或艉柱上）. 专业.专注.bending moment 弯矩bilge 舭部；舱底；（船底）污水沟bilge bracket 舭肘板bilge keel(chock, piece) 舭龙骨bilge knee 舭肘板bilge line 舭水管系bilge main 舭水总管bilge pipe (suction) 舭吸水管bilge pump 舭水泵bilge strake(plate) 舭列板bilge well 污水井bitt 系缆桩bollard 系缆桩；系船柱；双系柱bolster 枕垫bonnet 烟囱帽；机罩boom 杆；吊杆；桁；叉架boom crutch(support; rest) 吊杆支架bossing 尾管突出部；轴包套bottom frame 船底横骨bottom longitudinal 船底纵骨bottom plate 船底板bow 船首，船头bow fender 艏护垫bow flare 艏部外飘bow thruster 首侧推器bracket 肘板；（三角）拖架breakwater 挡浪板bridge 桥；桥楼；驾驶台bulb angle 圆头角材bulbous bow 球形船首，球鼻首bulb stern 球形船尾bulkhead 舱壁bulkhead plating 舱壁板bulkhead stiffener 舱壁扶强材bulwark 舷墙bulwark plating 舷墙板bulwark stay 舷墙扶强材bunker tank 燃料舱bushing 衬套butt 端接；残片butt joint(seam) 平接缝butt riveting 对接铆butt welding 对接焊butterfly clip 蝴蝶夹bypass valve 旁通阀cable stopper 止链器. 专业.专注.camber 翘曲camber of beam 梁拱cant beam 斜梁cant bracket 斜角板cant frame 斜肋骨cantilever 悬臂梁capstan 绞盘；绞缆机cargo batten 货舱护板cargo block 吊货滑车cargo port 装货舷梯，舷门cat walk （油轮上的）天桥，步桥center girder 中底桁center strake 中央内底板chafing plate 防擦板chafing ring 防擦环chain lock(well) 锚链舱chain pipe 锚链管chain stopper 止链器chock 导缆器；垫木clamp plate 夹板，压板cleat 羊角；系绳铁栓；防滑条coaming 围板；舱口围板cofferdam 隔离舱collar plate 封板collision bulkhead 船首舱壁；防撞舱壁companion way(hatch) 升降口corrugated bulkhead 槽形舱壁corrugation 皱；槽形；波形cross deck structure 舱间甲板结构crossing strength member 交叉强力构件cruiser stern 巡洋舰型船尾curtain plate 幕板cut out 开口；切davit 吊艇架；吊艇柱deck 甲板deck beam 甲板横梁deckhouse 甲板室deck line 甲板线deck longitudinal 甲板纵骨deck stringer(plate) 甲板边板deep tank 深舱derrick 吊杆diaphragm 隔板double bottom 双层底doubling plate 双层焊合板drain hole 排水孔. 专业.专注.duct keel 箱形龙骨dunnage 垫舱（物料）；衬垫dunnage wood 垫木dynamic load 动载荷end bracket 端肘板escape trunk （船内）应急通道engine bed 机座engine casing 机舱围壁escape scuttle （船内）应急出口escape vent 脱险口expansion joint 伸缩接头expansion trunk(tank) （油船）膨胀深井extension bracket 延伸肘板face plate 面板fender 碰垫；护舷材fender bar 护舷条fair lead 导缆器flame screen 防焰罩flange 折边flanged bracket 折边肘板flat keel 平板龙骨floor 肋板folding door 折门forecastle deck 艏楼甲板fore peak tank （船的）首舱；前尖舱forward perpendicular 首垂线foundation 底座frame 肋骨frame number 肋骨跨数frame space 肋距freeing port 甲板排水孔；放水孔gangway (gang ladder or gang board) 舷梯gasket 垫圈，垫料（集）密封垫general service pipe (G.S pump) 通用泵，总用泵girder 桁材gooseneck(parity iron) 鹅颈头；吊杆弯头grating 格子板；滑铁板ground tackle 锚泊索具gunwale 舷缘；舷边gunwale angle 舷边角钢gunwale bar 舷边角材gunwale railing 舷边栏杆gunwale tank 舷侧水柜（甲板下）gusset 角板；扣板gutter （甲板）水沟；槽沟. 专业.专注.gutter angle; waterway angle （舷侧）排水沟角钢gypsy 绞筒（锚机绞车上的）handrail 舷墙扶手hanging rudder; hinged rudder 吊舵；悬舵hatch; hatchway; hatch opening 舱口hatch bar 封舱压条hatch batten 舱口边压条hatch beam (web) 舱口大梁hatch booby 活动舱口盖hatch coaming 舱口板hatch cover 舱口盖hatch end beam 舱口端梁hatch moulding 舱口椽材hatch side girder 舱口纵桁hatch tarpaulin 盖舱布hatch trunk 舱口围阱hawse pipe 锚链管hawser 绳索；大缆heel 踵材；横倾hinged cover(door) 铰链盖（门）hold 货舱hold beam 舱内梁hold frame 舱内肋骨hold ladder 舱内梯hold stanchion(pillar) 舱内支柱hold stringer 舱内纵桁hopper 漏斗；开舱泥驳hopper tank 底边舱hopper tank sloping plating 底边舱斜板horizontal margin plate 水平内底板horizontal girder 水平桁horizontal stiffener 水平扶强材（防挠材）hull 船壳，船体hull construction 船体结构hull plating 船壳板hull strength 船体强度inner bottom 内底inner bottom plating 内底板insert plate 嵌板；衬板jack 千斤顶jack ladder 绳梯Jacob's ladder 软梯；绳梯Joggled joint 折接；弯合joggling machine 折曲机keel 龙骨. 专业.专注.keelblock 龙骨墩keel line 龙骨线；艏艉线keel plate 龙骨板keel rail （救生艇）艇底把手keelson 内龙骨kingpost 起重柱；将军柱knee 肘板；弯头knee of the deck 甲板梁肘板lightening hole 减轻孔lignum vitae 铁梨木local strength 局部强度local stress 局部应力longitudinal 纵骨；纵材；纵桁longitudinal bulkhead 纵舱壁longitudinal bending 纵向弯曲longitudinal framing system 纵骨架式longitudinal strength 纵向强度lug 耳板main deck 主甲板main frame 主肋骨manhole 人孔man hole door 人孔盖man hole coaming 人孔围板moment of inertia 惯性矩margin plate 内底边板molded breadth 型宽molded depth 型深mooring hole 导缆孔mooring post 系缆柱；岸柱mud box 泥箱non-return valve 止回阀non-watertight bulkhead 非水密舱壁notch 切口；槽口；刻痕oscillating load 振动负荷parallel middle body 平行中体panel stiffener 板格扶强材panting arrangement 防挠振结构panting beam 防挠振梁panting stringer 防挠振纵桁pillar 支柱；墩pintle 舵销plane bulkhead 平面舱壁plane keel 平板龙骨pump room 泵舱helm(rudder) pintle 舵销horizontal margin plate 水平内底边板. 专业.专注.out bottom plating 外底板platform 平台plating 壳板plimsoll mark 载重线标志poop 艉楼；船尾poop deck 艉楼甲板port 舷门；舱门；（装货）口；窗；门；孔porthole 舷窗；（装货）舷门propeller; propellor 推进器；螺旋桨propeller aperture 螺旋桨空间propeller boss(bub) 螺旋桨毂propeller shaft 艉轴racking （船体）横向挠度rail 扶手；栏杆rolling 横摇round of beam 梁拱round stern 圆（船）尾rudder 舵rudder carrier 舵托rudder casing 舵杆管rudder pintle 舵针；舵栓rudder plate; rudder blade 舵叶；舵板rudder post 舵柱rudder stock 舵杆rudder trunk 舵杆围壁；舵杆管rung （梯子）踏步；横档scallop 扇形开孔scantling 构件尺寸scantling of the structure 结构尺寸scarf; scarph 嵌接处；斜面；斜接scarf joint 斜（嵌）接scarf weld （斜面）焊接scarfing bracket 嵌接肘板scupper 排水孔scupper pipe 排水管scuttle 舷窗；人孔（盖）；小舱口盖seam 焊缝；接缝section 剖面section modulus 剖面模数semi-balanced rudder 半平衡舵shaft 轴shaft bracket 轴架shaft tube; stern tube 艉轴管shaft tunnel(alley; passage; trunk) 轴隧；地轴弄shedder plate 泄板；斜板sheer 舷弧；偏航. 专业.专注.sheer strake 舷顶列板shell 船壳；壳shell frame 舷侧肋骨shell plating 船壳板；外板shell strake; outside plating 船体外板shelter deck 遮蔽甲板shifting beam 活动舱口梁shifting board (or plank) 止移板（散装谷类）；防动板side girder 旁桁材side longitudinal 舷侧纵骨side plating 舷侧外板side strake 舷侧列板single bottom 单层底skid 护舷木；垫板skylight 天窗slanting plate 斜板slop tank 污油水舱sloping plate 斜板sloping plate longitudinal 斜板纵骨slot 槽；开缝sluice 水密门；水闸sluice valve 闸阀sniped end 削斜端soft toe 软趾solid floor 实肋板sounding pipe 测量管；测深管stabilizer 减摇装置stabilizing tank 减摇水舱staging 构架；台架；脚手架stanchion 支柱；栏杆柱static load 静载荷stay 支柱；撑条；支索stay bar(or rod) 撑杆stay plate 撑板stem 艏；艏柱；艏材stem post 艏柱stern 船尾，艉部stern counter 船尾突出体stern shaft; propeller shaft 艉轴stern poop 艉楼stern post 尾柱stiffener 防挠材；扶强材；加固物stool 托架，座，凳strake 列板strength calculation 强度计算. 专业.专注.strength deck 强力甲板stringer 纵桁stringer plate 甲板边板structural member 构件structural strength 结构强度strum box （舱底水）过滤箱strut 撑材，支柱，轴架stuffing box 填料箱superstructure 上层建筑tail (end) shaft 艉轴tarpaulin 防水油布，帆布，舱盖布thrust bearing(block) 推力轴承thrust shaft collars 推力环tieplate 带板，牵板，连接板topside tank 顶边舱；上边柜topside tank sloping plating 顶边舱斜板torsion 扭转torsion strength 扭转强度transom stern 方形船尾transverse 横梁，横材transverse bulkhead 横舱壁transverse frame 横肋骨，横框transverse framing system 横骨架式transverse ring 横环transverse strength 横向强度tripping bracket 防倾肘板tween deck 中间甲板tween deck frame 甲板间肋骨twisting distortion 扭转变形twisting moment 扭转力矩tunnel 轴隧，隧道，风筒tunnel escape 轴隧应急出口tunnel shaft bearing 中间轴支撑轴承ullage pipe (port) 油位测定管（孔）ullage space 空挡空间upper deck 上甲板upper (reverse) frame 内底横骨upper (lower) shelf plate 上（下）支架板upper (lower) stool 上（下）托架ventilator 通风筒vertical ballast trunk 竖向压载通道vertical girder 竖桁warping chocks 滚轮导缆钳wash bulkhead 可荡舱壁，挡水舱壁watertight bulkhead 水密舱壁watertight deck 水密门. 专业.专注.weather deck 露天甲板web beam 强横梁，桁板横梁web frame 加强肋骨，框架肋骨，桁板肋骨web plate 腹板wedge 楔木，楔子winch 起货机winch-head 绞车卷筒windlass 起锚机wing tank 翼舱，翼柜wire clip 钢缆夹wire reel 卷缆车，钢丝滚筒三、船舶材料及工艺常用英语A.Shipbuilding material (造船材料) T-bar T型钢Z-bar Z型钢I-B ar 工字钢channel bar 槽钢angle steel 角钢equal angle steel 等边角钢unequal angle steel 不等边角钢offset bulb plate 球扁钢flat plate 钢板round steel 圆钢half round steel 半圆钢steel pipe 钢管alloy steel 合金钢special steel 特种钢tempering steel 回火钢材low carbon steel 低碳钢high tensile steel 高强度钢copper 紫铜brass 黄铜aluminum alloy 铝合金stainless steel 不锈钢mechanical property 机械性能tensile test 拉伸试验bend test 弯曲试验impact test 冲击试验torsion test 扭转试验torsion strength 抗扭强度torsional deflection 扭转；扭转变形tensile strength 拉伸强度yield strength 屈服强度yield point 屈服点yield stress 屈服应力. 专业.专注.elastic limit 弹性极限ultimate strength 极限强度ultimate tensile stress 极限拉伸应力elasticity 弹性ductility 延展性，可塑（锻）性flexibility 挠性，柔性，易弯性toughness 韧性brittleness 脆性friability 易碎性hardness 硬度rigidity 刚性，稳定性heat treatment 热处理quench 淬火normalising 正火annealing 退火hardening 硬化，淬火tempering 回火casting 铸件，铸造forging 锻件，锻造pickling 酸洗ship timber 船用木材lignumvitae 铁梨木three-plywood 三夹板asbestos 石棉asbestos cloth 石棉布asbestos board 石棉板asbestos sheet 石棉纸asbestos cord 石棉绳asbestos paint 石棉涂料fiberglass 玻璃丝plastics 塑料resin 树脂rubber 橡皮painting 油漆cladding 镀层，表面处理coating 涂层，敷料corrosion 腐蚀，侵蚀wastage 损耗，蚀耗wear and tear 蚀损，磨损fracture 裂纹fatigue fracture 疲劳裂纹hairline fracture 发式裂纹buckling 皱折deformation 变形deflection, deflexion 挠曲flexion 弯曲. 专业.专注.lamellar tearing 层间撕裂rust 铁锈scale 锈皮pitting 点蚀，锈斑indent 凹痕，凹陷groove 槽沟detachment 脱开，脱焊rupture 断裂，破裂cropping 割掉renewal 换新descale 除锈grind 磨平be veed out 刨除alignment 对准，校直snip 剪断，剪片taper 削斜，斜度B.Shipbuilding workmanship （造船工艺）Working drawing 施工图end elevation 后面图front elevation 正面图side elevation 侧面图plane 平面图lines plan 型线图plan of waterlines 水线图general arrangement plan 总布置图construction plan 结构图damage plan 损坏示意图shell expansion plan 外板展开图docking plan 进坞图framing plan 船体构架图inboard profile plan 纵剖面图midship section plan 舯剖面图loaded waterline plane 满载水线图half breadth plan 半宽水线图stowage plan 配载图laying off lofting 放样mold loft floor 放样台mold loft 放样间template 样板mold loft batten, template batten 木样条evolute 展开线allowance 余量assembly 装配subassembly 分段装配subdivision length 分段长度shipbuilding tolerance 造船公差. 专业.专注.building berth 船台building dock 干坞slip dock 湿坞marine slipway, railway dry dock 船排marine slipway cradle 船排支架building block, stocks 枕木launch 下水launching ways 下水滑道launching grade 下水坡度launching cradle 下水架end launching 纵向下水side way launching 横向下水hydraulic press 水压机flanging machine 折边机plate bending machine 弯板机angle cutter 角钢切断机planing machine 刨边机shearing machine 剪床guillotine shear 龙门剪床oxy-acetylene welding 氧-乙炔焊co2 gas welding 二氧化碳气体焊arc welding 电弧焊unionmelt welding 埋弧自动焊fusion welding 熔焊fillet welding 角焊flat seam 对接缝butt joint welding 对接焊intermittent welding 间断焊；断续焊staggered intermittent welding 交错断续焊缝lap weld 搭接焊slot weld 槽焊；长孔焊plug weld 塞焊；圆孔焊run of welding 焊道welding torch 焊炬welding rod 焊条flux 焊药filler metal; deposited metal 熔敷金属welding stress 焊接应力welding procedure 焊接方法welding throat 焊喉cutting torch 割炬acetylene generator 乙炔发生器slag 熔渣undercut （焊接）咬边；根切hydraulic test 水压试验. 专业.专注.pressure test 压力试验flooding test 灌水试验hose test 冲水试验oil tight test 油密试验purchase trial 交船试验四、船舶性能常用英语angle of vanishing stability 稳性消失角buoyancy 浮性buoyancy curve 浮力曲线capsizing lever, upsetting lever 倾覆力臂capsizing moment, upsetting moment 倾覆力矩center of buoyancy 浮心center of floatation 漂心center of gravity 重心curve of areas of waterplanes 水线面积曲线curve of section areas 横剖面面积曲线curve of volumes of displacement 排水量曲线dynamical stability（curve）动稳性（曲线）entrance angle 进水角floodable length 可浸长度force of buoyancy, buoyant force 浮力free surface 自由液面heaving 垂荡heeling angle 横倾角heeling moment 横倾力矩hogging 中拱hogging condition 中拱状态hogging moment(stress) 中拱力矩（应力）hydrostatic curves 静水力曲线initial metacenter 初稳心initial stability 初稳性insubmersibility 抗沉性longitudinal inclination; list; heel 纵倾longitudinal stability 纵稳性panting （波浪对船体的）冲击period of rolling 横摇周期pitching 纵摇pounding 波浪冲击maneuverability 操纵性margin line 限界线metacenter 稳心moment to change trim one centimeter 每厘米纵倾力矩permissible length 许可长度. 专业.专注.potential head 势头pressure head 压头restoring moment, righting moment 复原力矩restoring lever, righting lever 复原力臂rolling 横摇sagging 中垂sagging condition 中垂状态sagging moment(stress) 中垂力矩（应力）seaworthiness 适航性stability 稳性stability at large angles 大倾角稳性stability criterion numeral 稳性横准数static head 静压头（力）statical stability (curve) 静稳性（曲线）surging 纵荡swaying 横荡tons per centimeter of immersion 每厘米吃水吨数total head (pressure) 总压头（力）transverse inclination, trim 纵倾transverse (longitudinal) metacenter 横（纵）稳心transverse (longitudinal) stability 横（纵）稳性trim by the bow (stern) 首（尾）倾turning quality (circle) 回转性（圈）velocity head 速头weigh curve 重力曲线yawing 艏摇五、船体检验常用英语THE DESCRIPTION OF DAMAGEA.General descriptions1.in good condition 情况良好2.in poor condition 情况欠佳3.in bad condition 情况不佳，情况不良4.in a neglected condition 缺乏保养5.not properly serviced 未经正常保养6.not properly cleaned 未经正常清洁7.not properly protected未经正常保护8.not properly insulated未经正常隔热（或电气绝缘）9.not properly adjusted 未经正常校正10.defective 有缺陷的（失效）11.damaged 损坏damaged beyond repair 损坏了无法修复. 专业.专注.12.failed (in failure) 失效13.cut of order (in trouble) 故障out of action 停止工作（作用），不是指故障14.in disorder 零乱（船属具零乱了）15.not working 不能工作16.inoperative 不能工作（失效）unworkable, inoperable 指本身不能工作，在损坏状况判断中不能使用17.out of function 不能工作，失去作用，不起作用18.unserviceable (useless) 不能使用（指必须换新的损坏部件）19.could not be started(failed to start)不能启动20.empty 空的21.fitted incorrectly 安装不正确（指小型的装置设备）installed incorrectly 安装不正确（指较大的装置设备）22.dangerous accumulation of inflammable vapors 可燃气体危险集积it was obvious that this state had existed for a considerable time （损坏）状况是长期存在的23.sluggish in (action, answering) （动作、应答）迟钝B.Deficiencies1.no…fitted, no…provided 未装2.no…available未备有3.missing 遗失4.incomplete 不齐全，不完整5.deficient 不足，缺少6.insufficient 不足7.neglected 遗漏8.omitted 遗漏，省去9.removed 移开，拆走10.washed overboard 冲走11.dropped 跌落12.fitted with wrong ….(size, material, devices…)错用（尺寸，材料，仪器）C.Tightness, stains, loss of etc.1.Leaking 漏2.infiltrating (seeping) 渗漏3.weeping 泪滴. 专业.专注.4.sweating 汗滴5.not watertight 不水密6.loss of watertightness 失去水密性（比5好）7.loss of airtightness 失去气密性8.loss of oiltightness 失去油密性9.escaping of cool 逃冷10.loss of lub-oil pressure 滑油压力降低11.loss of water pressure 水压力降低12.oil polluted 油污染13.oil soaked 油浸14.water soaked 水浸15.water stained 水渍16.oil stained 油渍17.rust in patches 锈斑18.verdigris in patches 铜绿斑19.water marks 水渍D.Crack, score, break etc.1.scuffed 拉毛（仅从反光上可观察到）2.chafed 擦痕3.scored 拉痕（痕较chafed深）4.scratched 抓痕（硬拉过的痕）5.scraped 刮痕（长期运行刮的痕）6.grooved 槽痕（比pitting深）7.ridged 凸起雷治痕（环状的痕）8.cracked 裂痕hair crack 发痕surface crack 表面裂痕through crack 穿透裂痕non-through crack 未穿透裂痕9.chapped 龟裂，折裂10.fractured 折裂11.broken off 破掉（破裂后跌落）broken 破裂，破碎12.holed 穿洞13.holed & flooded 破洞浸水14.opened 开口15.bent 弯曲16.canted 倾斜17.buckled 皱折18.warped 翘起，翘曲19.indented (dented) 凹痕，凹陷（指船壳板在两档肋位间的凹陷）20.set in 凹陷（指船壳板较大面积的凹陷）21.waved 波曲. 专业.专注.22.curled 卷曲（指绳索）23.rumpled 褶皱（指垫片）24.bulged 鼓起，凸出25.collapsed 倾陷，倾倒26.ruptured 毁损27.torn off 撕破torn 拉脱28.pierced 刺破29.peeled 剥皮（油漆剥落）30.burst 爆破（指高压管路）31.blown off (packing) 吹脱32.distorted 扭曲，歪扭33.engine break-down 因故障机器突然停车E.Corrosion, seizing, choking etc.1.corrosion 腐蚀2.wasted 耗油3.deteriorated 蚀薄4.thinned 变薄5.pitted 麻点6.eroded 侵蚀7.rusted 生锈8.rotten （木、橡胶）腐烂、腐坏9.decayed （电缆）腐烂、腐坏10. aerated（橡胶、电缆）腐烂、腐坏11. aged 老化12. seized 咬住13. seized by corrosion 锈死14. stuck （粘）咬住15. rust-jammed 锈轧16. fouled 拥塞17. clogged堵塞（常指管子的堵塞）18. blocked 阻塞19. gagged 塞口20. foul & dirty 闭塞21. blanked 封没22. plugged 闭塞23. choked 卡住，阻塞F.Wear, loose, clearance etc.1.Loose 松动2.starting （铆钉）松动3.slack 松动slack back 松出4.worn 磨损5.worn cut evenly 均匀磨损6.worn cut unevenly 不均匀磨损. 专业.专注.7.worn on one side 单边磨损8.worn out symmetrically 对称磨损9.distorted （轴线弯曲并扭转）扭曲10.sprung （铆钉）扭歪11.twisted （轴线未弯、纯扭转）扭转12.excess clearance 间隙过大13.excess backlash 齿隙过大14.excess vibration 振动过大15.excess noise level 噪音过大16.loose engagement 啮合太松17.loose connection 接头松动18.tooth 齿worn out 磨损chopped off 崩缺fractured 折断19.knocking 敲击knocking cylinder 敲缸knocking valve gear 伐件敲缸knocking bearing 轴承敲缸20.bearing metal 轴承合金detached 脱壳cracked 开裂wiped 铺铅belted 熔化oil groove blocked 油槽堵塞21.out off roundness 失圆22.out off alignment 拉线不直23.off-centering 偏心24.deflected 偏斜G.Burning, heating, etc.1.Sparking 火花2.arcking (arcing) 电弧mutator 整流器scored 拉痕burnt 烧坏worn 磨耗，磨损uneven 不平sparking 火花blackened 发黑rough 粗糙mica undercut 弧坑4.brush set incorrectly 碳刷安装不正确5.scorched 烤焦6.coked 结焦7.charred 结碳8.overheated 过热. 专业.专注.9.broken down 击穿10. short-circuit 短路11. setting incorrect 整定值不正确12. tripped incorrect 脱扣不正常13. batteriescompletely discharged（电）完全发光undercharged 未充满overcharged 充电过量dry water 水干A. Remove, crop etc.1.Removed 拆下2.removed & replaced 拆装3.removed, faired & replaced拆装拷平4.cropped & renewed 割换（管、板、栏杆）5.partly renewed 部分换新6.partly cropped & renewed 部分割换7.cut off 割除8.faired 拷平9.faired on 原地拷平10.faired in place 原地拷平11.straightened 拷直、校直12.dismantle 拆卸（某一零件）13.disassembled 拆散（解体）14.stripped 拆除（某一部件）15.unshipped 拆下16.disconnected 断开（线、管接头）17.opened 打开18.lifted 抬升、举起19.jacked 顶起（用千斤顶顶起）20.replaced (by, with) 换用21.patch 贴补B.Fit, scrape, grind etc.1.fitted & scraped 拂刮2.fitted & ground 拂磨3.scraped & ground 刮磨4.made to fit 拂合（装配好）5.run to fit 跑合（运动磨合）6.ground round 磨圆7.ground smooth 磨光8.ground & reamed 磨绞9.bored round 镗圆10.planed smooth 刨光11.polished 抛光12.machined 光车13.skimmed 光刀. 专业.专注.14.finish machined 精加工15.rough machine 粗加工C.Re-metal, adjust, check etc1.Remetalled 重浇白合金2.re-babbitted 重浇白合金（专指巴氏合金）3.pulled out 拉出4.drawn out 抽出5.taken out 取出6.adjusted 调整，校正adjusted for alignment 校正拉线adjusted true 校正拉线adjusted for clearance 校正间隙adjusted for centering 校中adjusted for deflection 校偏7.checked 检查checked for roundness 检查圆度checked for insulation resistance 检查绝缘电阻checked for centering检查中心位置checked for alignment 检查拉线checked for clearance 检查间隙8.cleaned 清洁9.wire-scrubbed 钢丝刷（除锈）10.chipped & scraped 拷锈（油漆）11.measured & recorded 测量并记录12.logged (hourly) 记录（小时）D.weld, rivet, wind etc.1.r epaired by welding 电焊修理2.w elded 补焊、焊接3.c losed up by welds （面积、深度、高度较大）焊补4.b uilt up by welds 堆焊5.p lug welded 塞焊6.s pot welded 点焊7.b utt welded 对接焊8 tackweld 点焊、平头焊、定位焊. 专业.专注.。

一、船舶类型常用英语ship, vessel 船，船舶boat, craft 艇sampan 舢板, 小船manpowered boat 人力船sailor; sailing boat 帆船motor sailor 机帆船power-driven ship 机动船paddle steamer, paddle wheel vessel 明轮船screw ship; propeller vessel 螺旋桨船airscrew ship; aerial propeller vessel 空气螺旋桨船hovercraft; aircushion craft 气垫船hydrofoil 水翼船hydrojet propelled boat, water jet boat 喷水船steamship; steamer 蒸汽机船motor ship 内燃机船diesel ship 柴油机船electrically-propelled ship 电力推进船steam turbine ship 汽轮机船gas turbine ship 燃气轮机船nuclear-power ship 核动力船deck ship 甲板船flush deck ship 平甲板船raised quarter-deck ship 尾升高甲板船well-deck ship 半舱船single side ship 单舷长大舱口船three-island ship 三岛式船double shell ship 双壳船riveted ship 铆接船welded ship 焊接船transversely framed ship 横骨架式船longitudinally framed ship 纵骨架式船combined framed ship 混合骨架式船sea-going vessel 海船ocean-going vessel 远洋船coaster 沿海船channel ship 海峡船inland waterway vessel 内河船civil ship; merchant ship 民用船；商船transport ship 运输船pleasure yacht 游艇passenger ship 客船coasting passenger and cargo ship沿海客货船passenger and auto-car carrier 旅客及汽车运输船tourist ship; passenger carrier 旅游船cargo ship; freighter 货船cargo liner 定期货船tramp ship 不定期货船container ship 集装箱船full-container ship 全集装箱船semi-container ship 半集装箱船multi-purpose container ship 多用途集装箱船general cargo ship/vessel/carrier 杂货船bulk (cargo) carrier 散货船ore carrier 矿砂船grain carrier 运粮船coal carrier; coaler 运煤船lumber(timber) carrier 运木船cattle carrier 运牲畜船multi-purpose ship 多用途船liquid cargo ship 液体货货船chemical tank 化学品液货船liquid chemical tanker 液体化学品船liquefied gas carrier 液化气体船liquefied petroleum gas tanker (LPG) 液化石油气运输船liquefied natural gas tanker (LNG) 液化天然气运输船tanker; oil tanker 油轮super tanker 超级油轮VLCC (very large crude carrier) (吨位在20万至30 万吨之间的) 巨型油轮ULCC (ultra-large crude carrier) (吨位在30万至50万吨之间的) 超巨型油船refrigerated ship; cold storage ship 冷藏船roll-on/roll-off ship (RO/RO ship) 滚装船ferry 渡船passenger ferry 旅客渡船freight ferry 货物渡船fishing vessel(boat) 渔轮trawler 拖网渔轮barge carrier; lighter aboard ship(LASH)载驳船barge; lighter 驳船deck barge 甲板驳well-deck barge 半舱驳double shell barge 双壳驳single side barge 单舷长大舱口驳oil barge 油驳container barge 集装箱驳船RO/RO barge 滚装驳船liquefied gas barge 液化气体驳hopper barge 开底泥驳split hopper barge 对开泥驳pusher; pushboat 顶推船；推船working ship 工程船tug; tugboat; towboat 拖船第 1 页共12 页。

船舶常用英语(一)一、船舶类型常用英语ship, vessel 船，船舶boat, craft 艇sampan舢板, 小船manpowered boat人力船sailor; sailing boat 帆船motor sailor 机帆船power-driven ship 机动船paddle steamer, paddle wheel vessel 明轮船screw ship; propeller vessel 螺旋桨船airscrew ship; aerial propeller vessel 空气螺旋桨船hovercraft; aircushioncraft 气垫船hydrofoil水翼船hydrojet propelled boat, water jet boat 喷水船steamship; steamer 蒸汽机船motor ship 内燃机船diesel ship 柴油机船electrically-propelledship 电力推进船steam turbine ship 汽轮机船gas turbine ship 燃气轮机船nuclear-power ship核动力船deck ship 甲板船flush deck ship 平甲板船raised quarter-deck shipVLCC (very large crude carrier) (吨位在20万至30 万吨之间的) 巨型油轮ULCC (ultra-large crude carrier) (吨位在30万至50万吨之间的) 超巨型油船refrigerated ship; cold storage ship 冷藏船roll-on/roll-off ship(RO/RO ship) 滚装船ferry渡船passenger ferry 旅客渡船freight ferry 货物渡船fishing vessel(boat) 渔轮trawler拖网渔轮barge carrier; lighteraboard ship(LASH)载驳船barge; lighter 驳船deck barge 甲板驳well-deck barge 半舱驳double shell barge 双壳驳single side barge 单舷长大舱口驳oil barge 油驳container barge 集装箱驳船RO/RO barge 滚装驳船liquefied gas barge 液化气体驳hopper barge 开底泥驳split hopper barge 对开泥驳pusher; pushboat 顶推船；推船working ship 工程船tug; tugboat; towboat 拖船harbor tug 港作拖船rescue tug 救助拖轮salvage ship 救捞船dredger挖泥船trailing suction dredge 耙吸挖泥船cutter suction dredger 绞吸挖泥船bucket wheel dredger 斗轮挖泥船bucket dredger 链斗挖泥船reclamation craft吹泥船grab dredger 抓斗挖泥船dipper dredger 铲斗挖泥船floating pitter; drive pitter 打桩船floating crane; derrick boat 起重船floating dock 浮船坞cable layer; cable ship 布缆船scientific surveying ship 科学考察船research ship 科学调查船oceanographic research vessel 海洋调查船surveying ship 测量船ice-breaker破冰船pontoon 浮舟; 浮桥; 趸船, 浮码头high speed craft 高速船passenger catamaran 双体客船vehicle ferry catamaran 双体车辆渡船vehicle-passenger ferry catamaran 双体车客渡船pontoon catamaran 双体趸船二、船舶结构常用英语center line 中心线，中线athwartships 横对船体（与船首尾线直交）bevel斜角；斜面base line 基线amidships 在船中部；在纵中线上designed waterline breadth 设计水线宽designed waterline length 设计水线长draft吃水former/aft draft 首/尾吃水draft figures 吃水尺度intersection 交点；交叉；横断面knuckle折角线length between perpendicular 垂线间长length overall 总长load waterline length 满载水线长register length (breadth;depth) 登记长度（宽度、深度）freeboard干舷rise of floor (dead; rise) 舭高；船底loadlinemark载重水线标记fresh water load line (F.) 淡水载重线fresh water timber load line (L.F.) 淡水木材载重线tropical fresh water load line (TF) 热带淡水载重线tropical load line (T) 热带载重线summer load line(S) 夏季载重线summer freshwater load line(F) 夏季淡水载重线winter load line(W) 冬季载重线winter North Atlantic load line(WNA) 冬季北大西洋载重线even keel （首尾）等吃水，平载extreme breadth 最大宽度floatable length 可浸长度sheer at forward (after) perpendicular 首尾舷弧sheer line 舷弧线accommodation居住舱室accommodation deck 起居舱室；旅客甲板accommodation ladder舷梯accommodation ladder platform 舷梯平台accommodation laddermanrope 舷梯扶索after body 后（部船）体after peak bulkhead 艉尖舱舱壁after peak tank 艉尖舱air hole 空气孔air pipe 空气管appendage （船体水线下的）附体；附件auxiliary machinery 辅助机械；辅机balanced rudder 平衡舵ballast压载（物）ballast line压载水管系ballast pump 压载水泵ballast pumping system 压载水系统ballast tank(water) 压载舱（水）batten 板条；压条（封仓用）batten-ceiling （货舱内）护舱条，护板beam横梁beam bracket 梁肘板bearding 交合线，榫（艏柱或艉柱上）bending moment 弯矩bilge 舭部；舱底；（船底）污水沟bilge bracket 舭肘板bilge keel(chock, piece) 舭龙骨bilge knee 舭肘板bilge line 舭水管系bilge main 舭水总管bilge pipe (suction) 舭吸水管bilge pump 舭水泵bilge strake(plate) 舭列板bilge well 污水井bitt系缆桩bollard 系缆桩；系船柱；双系柱bolster枕垫bonnet烟囱帽；机罩boom 杆；吊杆；桁；叉架boom crutch(support; rest) 吊杆支架bossing 尾管突出部；轴包套bottom frame 船底横骨bottom longitudinal 船底纵骨bottom plate 船底板bow船首，船头bow fender 艏护垫bow flare 艏部外飘bow thruster 首侧推器bracket 肘板；（三角）拖架breakwater挡浪板bridge桥；桥楼；驾驶台bulb angle 圆头角材bulbous bow 球形船首，球鼻首bulb stern 球形船尾bulkhead舱壁bulkhead plating 舱壁板bulkhead stiffener 舱壁扶强材bulwark舷墙bulwark plating 舷墙板bulwark stay 舷墙扶强材bunker tank燃料舱bushing衬套butt端接；残片butt joint(seam) 平接缝butt riveting 对接铆butt welding 对接焊butterfly clip 蝴蝶夹bypass valve 旁通阀cable stopper 止链器camber翘曲camber of beam 梁拱cant beam 斜梁cant bracket 斜角板cant frame 斜肋骨cantilever悬臂梁capstan绞盘；绞缆机cargo batten 货舱护板cargo block 吊货滑车cargo port 装货舷梯，舷门cat walk （油轮上的）天桥，步桥center girder 中底桁center strake 中央内底板chafing plate 防擦板chafing ring防擦环chain lock(well) 锚链舱chain pipe 锚链管chain stopper 止链器chock导缆器；垫木clamp plate 夹板，压板cleat 羊角；系绳铁栓；防滑条coaming围板；舱口围板cofferdam隔离舱collar plate 封板collision bulkhead 船首舱壁；防撞舱壁companion way(hatch) 升降口corrugated bulkhead 槽形舱壁corrugation皱；槽形；波形cross deck structure 舱间甲板结构crossing strength member 交叉强力构件cruiser stern 巡洋舰型船尾curtain plate 幕板cut out 开口；切davit吊艇架；吊艇柱deck甲板deck beam 甲板横梁deckhouse甲板室deck line甲板线deck longitudinal 甲板纵骨deck stringer(plate) 甲板边板deep tank 深舱derrick吊杆diaphragm隔板double bottom 双层底doubling plate 双层焊合板drain hole 排水孔duct keel 箱形龙骨dunnage 垫舱（物料）；衬垫dunnage wood 垫木dynamic load 动载荷end bracket 端肘板escape trunk （船内）应急通道engine bed 机座engine casing 机舱围壁escape scuttle （船内）应急出口escape vent 脱险口expansion joint 伸缩接头expansion trunk(tank) （油船）膨胀深井extension bracket 延伸肘板face plate 面板fender碰垫；护舷材fender bar 护舷条fair lead 导缆器flame screen 防焰罩flange折边flanged bracket 折边肘板flat keel 平板龙骨floor肋板folding door 折门forecastle deck 艏楼甲板fore peak tank （船的）首舱；前尖舱forward perpendicular 首垂线foundation底座frame肋骨frame number 肋骨跨数frame space 肋距freeing port 甲板排水孔；放水孔gangway (gang ladder or gang board) 舷梯gasket 垫圈，垫料（集）密封垫general service pipe (G.S pump) 通用泵，总用泵girder桁材gooseneck(parity iron) 鹅颈头；吊杆弯头grating格子板；滑铁板ground tackle 锚泊索具gunwale舷缘；舷边gunwale angle 舷边角钢gunwale bar 舷边角材gunwale railing 舷边栏杆gunwale tank 舷侧水柜（甲板下）gusset角板；扣板gutter （甲板）水沟；槽沟gutter angle; waterway angle （舷侧）排水沟角钢gypsy 绞筒（锚机绞车上的）handrail舷墙扶手hanging rudder; hinged rudder 吊舵；悬舵hatch; hatchway; hatch opening 舱口hatch bar 封舱压条hatch batten 舱口边压条hatch beam (web) 舱口大梁hatch booby 活动舱口盖hatch coaming 舱口板hatch cover 舱口盖hatch end beam 舱口端梁hatch moulding 舱口椽材hatch side girder 舱口纵桁hatch tarpaulin盖舱布hatch trunk 舱口围阱hawse pipe 锚链管hawser绳索；大缆heel踵材；横倾hinged cover(door) 铰链盖（门）hold货舱hold beam 舱内梁hold frame 舱内肋骨hold ladder 舱内梯hold stanchion(pillar) 舱内支柱hold stringer 舱内纵桁hopper漏斗；开舱泥驳hopper tank 底边舱hopper tank sloping plating 底边舱斜板horizontal margin plate 水平内底板horizontal girder 水平桁horizontal stiffener 水平扶强材（防挠材）hull船壳，船体hull construction 船体结构hull plating 船壳板hull strength 船体强度inner bottom 内底inner bottom plating 内底板insert plate 嵌板；衬板jack千斤顶jack ladder 绳梯Jacob's ladder 软梯；绳梯Joggled joint 折接；弯合joggling machine 折曲机keel龙骨keelblock龙骨墩keel line 龙骨线；艏艉线keel plate 龙骨板keel rail （救生艇）艇底把手keelson内龙骨kingpost起重柱；将军柱knee肘板；弯头knee of the deck 甲板梁肘板lightening hole 减轻孔lignum vitae 铁梨木local strength 局部强度local stress 局部应力longitudinal纵骨；纵材；纵桁longitudinal bulkhead 纵舱壁longitudinal bending 纵向弯曲longitudinal framingsystem 纵骨架式longitudinal strength 纵向强度lug耳板main deck 主甲板main frame 主肋骨manhole人孔man hole door 人孔盖man hole coaming 人孔围板moment of inertia 惯性矩margin plate 内底边板molded breadth 型宽molded depth 型深mooring hole 导缆孔mooring post 系缆柱；岸柱mud box 泥箱non-return valve 止回阀non-watertight bulkhead 非水密舱壁notch 切口；槽口；刻痕oscillating load 振动负荷parallel middle body 平行中体panel stiffener 板格扶强材panting arrangement 防挠振结构panting beam 防挠振梁panting stringer防挠振纵桁pillar支柱；墩pintle舵销plane bulkhead 平面舱壁plane keel 平板龙骨pump room 泵舱helm(rudder) pintle 舵销horizontal margin plate 水平内底边板out bottom plating 外底板platform平台plating壳板plimsoll mark 载重线标志poop艉楼；船尾poop deck 艉楼甲板port 舷门；舱门；（装货）口；窗；门；孔porthole 舷窗；（装货）舷门propeller; propellor 推进器；螺旋桨propeller aperture 螺旋桨空间propeller boss(bub) 螺旋桨毂propeller shaft 艉轴racking（船体）横向挠度rail扶手；栏杆rolling横摇round of beam梁拱round stern 圆（船）尾rudder舵rudder carrier 舵托rudder casing 舵杆管rudder pintle 舵针；舵栓rudder plate; rudder blade 舵叶；舵板rudder post 舵柱rudder stock 舵杆rudder trunk 舵杆围壁；舵杆管rung （梯子）踏步；横档scallop扇形开孔scantling构件尺寸scantling of the structure 结构尺寸scarf; scarph 嵌接处；斜面；斜接scarf joint 斜（嵌）接scarf weld （斜面）焊接scarfing bracket 嵌接肘板scupper排水孔scupper pipe 排水管scuttle 舷窗；人孔（盖）；小舱口盖seam焊缝；接缝section剖面section modulus剖面模数semi-balanced rudder半平衡舵shaft轴shaft bracket 轴架shaft tube; stern tube 艉轴管shaft tunnel(alley; passage;trunk) 轴隧；地轴弄shedder plate 泄板；斜板sheer舷弧；偏航sheer strake 舷顶列板shell船壳；壳shell frame 舷侧肋骨shell plating 船壳板；外板shell strake; outside plating 船体外板shelter deck 遮蔽甲板shifting beam 活动舱口梁shifting board (or plank) 止移板（散装谷类）；防动板side girder 旁桁材side longitudinal 舷侧纵骨side plating 舷侧外板side strake 舷侧列板single bottom 单层底skid护舷木；垫板skylight天窗slanting plate 斜板slop tank 污油水舱sloping plate 斜板sloping plate longitudinal 斜板纵骨slot槽；开缝sluice水密门；水闸sluice valve 闸阀sniped end 削斜端soft toe 软趾solid floor 实肋板sounding pipe 测量管；测深管stabilizer减摇装置stabilizing tank 减摇水舱staging 构架；台架；脚手架stanchion支柱；栏杆柱static load 静载荷stay 支柱；撑条；支索stay bar(or rod) 撑杆stay plate 撑板stem艏；艏柱；艏材stem post 艏柱stern船尾，艉部stern counter 船尾突出体stern shaft; propeller shaft 艉轴stern poop 艉楼stern post 尾柱stiffener 防挠材；扶强材；加固物stool托架，座，凳strake列板strength calculation 强度计算strength deck 强力甲板stringer纵桁stringer plate 甲板边板structural member 构件structural strength结构强度strum box （舱底水）过滤箱strut 撑材，支柱，轴架stuffing box 填料箱superstructure上层建筑tail (end) shaft 艉轴tarpaulin 防水油布，帆布，舱盖布thrust bearing(block) 推力轴承thrust shaft collars 推力环tieplate 带板，牵板，连接板topside tank 顶边舱；上边柜topside tank sloping plating 顶边舱斜板torsion扭转torsion strength 扭转强度transom stern 方形船尾transverse横梁，横材transverse bulkhead 横舱壁transverse frame 横肋骨，横框transverse framing system 横骨架式transverse ring 横环transverse strength 横向强度tripping bracket 防倾肘板tween deck 中间甲板tween deck frame 甲板间肋骨twisting distortion 扭转变形twisting moment 扭转力矩tunnel 轴隧，隧道，风筒tunnel escape 轴隧应急出口tunnel shaft bearing 中间轴支撑轴承ullage pipe (port) 油位测定管（孔）ullage space 空挡空间upper deck 上甲板upper (reverse) frame 内底横骨upper (lower) shelf plate 上（下）支架板upper (lower) stool上（下）托架ventilator通风筒vertical ballast trunk 竖向压载通道vertical girder 竖桁warping chocks 滚轮导缆钳wash bulkhead 可荡舱壁，挡水舱壁watertight bulkhead 水密舱壁watertight deck 水密门weather deck 露天甲板web beam 强横梁，桁板横梁web frame 加强肋骨，框架肋骨，桁板肋骨web plate 腹板wedge楔木，楔子winch起货机winch-head绞车卷筒windlass起锚机wing tank 翼舱，翼柜wire clip 钢缆夹wire reel 卷缆车，钢丝滚筒三、船舶材料及工艺常用英语A.Shipbuilding material(造船材料)T-bar T型钢Z-bar Z型钢I-Bar 工字钢channel bar 槽钢angle steel 角钢equal angle steel 等边角钢unequal angle steel 不等边角钢offset bulb plate 球扁钢flat plate 钢板round steel 圆钢half round steel 半圆钢steel pipe 钢管alloy steel 合金钢special steel 特种钢tempering steel 回火钢材low carbon steel 低碳钢high tensile steel 高强度钢copper 紫铜brass 黄铜aluminum alloy 铝合金stainless steel 不锈钢mechanical property 机械性能tensile test 拉伸试验bend test 弯曲试验impact test 冲击试验torsion test 扭转试验torsion strength 抗扭强度torsional deflection 扭转；扭转变形tensile strength 拉伸强度yield strength 屈服强度yield point 屈服点yield stress 屈服应力elastic limit 弹性极限ultimate strength 极限强度ultimate tensile stress 极限拉伸应力elasticity 弹性ductility 延展性，可塑（锻）性flexibility 挠性，柔性，易弯性toughness 韧性brittleness 脆性friability 易碎性hardness 硬度rigidity 刚性，稳定性heat treatment 热处理quench 淬火normalising 正火annealing 退火hardening 硬化，淬火tempering 回火casting 铸件，铸造forging 锻件，锻造pickling 酸洗ship timber 船用木材lignumvitae 铁梨木three-plywood 三夹板asbestos 石棉asbestos cloth 石棉布asbestos board 石棉板asbestos sheet 石棉纸asbestos cord 石棉绳asbestos paint 石棉涂料fiberglass 玻璃丝plastics 塑料resin 树脂rubber 橡皮painting 油漆cladding 镀层，表面处理coating 涂层，敷料corrosion 腐蚀，侵蚀wastage 损耗，蚀耗wear and tear 蚀损，磨损fracture 裂纹fatigue fracture 疲劳裂纹hairline fracture 发式裂纹buckling 皱折deformation 变形deflection, deflexion 挠曲flexion 弯曲lamellar tearing 层间撕裂rust 铁锈scale 锈皮pitting 点蚀，锈斑indent 凹痕，凹陷groove 槽沟detachment 脱开，脱焊rupture 断裂，破裂cropping 割掉renewal 换新descale 除锈grind 磨平be veed out 刨除alignment 对准，校直snip 剪断，剪片taper 削斜，斜度B.Shipbuildingworkmanship （造船工艺）Working drawing 施工图end elevation 后面图front elevation 正面图side elevation 侧面图plane 平面图lines plan 型线图plan of waterlines 水线图general arrangement plan 总布置图construction plan 结构图damage plan 损坏示意图shell expansion plan 外板展开图docking plan 进坞图framing plan 船体构架图inboard profile plan 纵剖面图midship section plan 舯剖面图loaded waterline plane 满载水线图half breadth plan 半宽水线图stowage plan 配载图laying off lofting 放样mold loft floor 放样台mold loft 放样间template 样板mold loft batten, template batten 木样条evolute 展开线allowance 余量assembly 装配subassembly 分段装配subdivision length 分段长度shipbuilding tolerance 造船公差building berth 船台building dock 干坞slip dock 湿坞marine slipway, railway dry dock 船排marine slipway cradle 船排支架building block, stocks 枕木launch 下水launching ways 下水滑道launching grade 下水坡度launching cradle 下水架end launching 纵向下水side way launching 横向下水hydraulic press 水压机flanging machine 折边机plate bending machine 弯板机angle cutter 角钢切断机planing machine 刨边机shearing machine 剪床guillotine shear 龙门剪床oxy-acetylene welding 氧-乙炔焊co2gas welding 二氧化碳气体焊arc welding 电弧焊unionmelt welding 埋弧自动焊fusion welding 熔焊fillet welding 角焊flat seam 对接缝butt joint welding 对接焊intermittent welding 间断焊；断续焊staggered intermittent welding 交错断续焊缝lap weld 搭接焊slot weld 槽焊；长孔焊plug weld 塞焊；圆孔焊run of welding 焊道welding torch 焊炬welding rod 焊条flux 焊药filler metal; deposited metal 熔敷金属welding stress 焊接应力welding procedure 焊接方法welding throat 焊喉cutting torch 割炬acetylene generator 乙炔发生器slag 熔渣undercut （焊接）咬边；根切hydraulic test 水压试验pressure test 压力试验flooding test 灌水试验hose test 冲水试验oil tight test 油密试验purchase trial 交船试验四、船舶性能常用英语第 31 页共 45 页angle of vanishing stability 稳性消失角buoyancy 浮性buoyancy curve 浮力曲线capsizing lever, upsetting lever 倾覆力臂capsizing moment, upsetting moment倾覆力矩center of buoyancy 浮心center of floatation 漂心center of gravity 重心curve of areas of waterplanes 水线面积曲线curve of section areas 横剖面面积曲线curve of volumes of displacement 排水量曲线dynamical stability（curve）动稳性（曲线）entrance angle 进水角floodable length 可浸长度force of buoyancy, buoyant force 浮力free surface 自由液面heaving 垂荡heeling angle 横倾角heeling moment 横倾力矩hogging 中拱hogging condition 中拱状态hogging moment(stress) 中拱力矩（应力）hydrostatic curves 静水力曲线initial metacenter 初稳心initial stability 初稳性insubmersibility 抗沉性longitudinal inclination;第 32 页共 45 页list; heel 纵倾longitudinal stability 纵稳性panting （波浪对船体的）冲击period of rolling 横摇周期pitching 纵摇pounding 波浪冲击maneuverability 操纵性margin line 限界线metacenter 稳心moment to change trim one centimeter 每厘米纵倾力矩permissible length 许可长度potential head 势头pressure head 压头restoring moment, righting moment 复原力矩restoring lever, righting lever 复原力臂rolling 横摇sagging 中垂sagging condition 中垂状态sagging moment(stress) 中垂力矩（应力）seaworthiness 适航性stability 稳性stability at large angles 大倾角稳性stability criterion numeral 稳性横准数static head 静压头（力）statical stability (curve) 静稳性（曲线）surging 纵荡swaying 横荡tons per centimeter of immersion 每厘米吃水吨数total head (pressure) 总压头（力）transverse inclination, trim第 33 页共 45 页纵倾transverse (longitudinal) metacenter 横（纵）稳心transverse (longitudinal) stability 横（纵）稳性trim by the bow (stern) 首（尾）倾turning quality (circle) 回转性（圈）velocity head 速头weigh curve 重力曲线yawing 艏摇五、船体检验常用英语THE DESCRIPTION OF DAMAGEA.General descriptions1.in good condition情况良好2.in poor condition情况欠佳3.in bad condition 情况不佳，情况不良4.in a neglectedcondition 缺乏保养5.not properly serviced未经正常保养6.not properly cleaned未经正常清洁7.not properly protected未经正常保护8.not properly insulated未经正常隔热（或电气绝缘）9.not properly adjusted未经正常校正10.defective 有缺陷的（失效）11.damaged损坏damaged beyondrepair 损坏了无法修复12.failed (in failure)第 34 页共 45 页失效13.cut of order (in trouble)故障out of action 停止工作（作用），不是指故障14.in disorder 零乱（船属具零乱了）15.not working 不能工作16.inoperative 不能工作（失效）unworkable, inoperable 指本身不能工作，在损坏状况判断中不能使用17.out of function 不能工作，失去作用，不起作用18.unserviceable (useless)不能使用（指必须换新的损坏部件）19.could not bestarted(failed to start)不能启动20.empty 空的21.fitted incorrectly安装不正确（指小型的装置设备）installed incorrectly 安装不正确（指较大的装置设备）22.dangerousaccumulation ofinflammable vapors可燃气体危险集积it was obvious that this state had existedfor a considerable time（损坏）状况是长期存在的23.sluggish in (action,answering) （动作、应答）迟钝B.Deficiencies1.no…fitted,no…provided 未第 35 页共 45 页装2.no…available未备有3.missing遗失4.incomplete 不齐全，不完整5.deficient不足，缺少6.insufficient不足7.neglected遗漏8.omitted遗漏，省去9.removed移开，拆走10.washed overboard冲走11.dropped跌落12.fitted with wrong ….(size, material,devices…)错用（尺寸，材料，仪器）C.Tightness, stains, lossof etc.1.Leaking漏2.infiltrating (seeping)渗漏3.weeping泪滴4.sweating汗滴5.not watertight不水密6.loss of watertightness失去水密性（比5好）7.loss of airtightness失去气密性8.loss of oiltightness失去油密性9.escaping of cool逃冷第 36 页共 45 页10.loss of lub-oil pressure滑油压力降低11.loss of water pressure水压力降低12.oil polluted油污染13.oil soaked油浸14.water soaked水浸15.water stained水渍16.oil stained油渍17.rust in patches锈斑18.verdigris in patches铜绿斑19.water marks水渍D.Crack, score, breaketc.1.scuffed 拉毛（仅从反光上可观察到）2.chafed擦痕3.scored 拉痕（痕较chafed深）4.scratched 抓痕（硬拉过的痕）5.scraped 刮痕（长期运行刮的痕）6.grooved 槽痕（比pitting深）7.ridged 凸起雷治痕（环状的痕）8.cracked裂痕hair crack 发痕surface crack 表面裂痕through crack 穿透裂痕non-through crack 未穿透裂痕第 37 页共 45 页9.chapped龟裂，折裂10.fractured折裂11.broken off 破掉（破裂后跌落）broken 破裂，破碎12.holed穿洞13.holed & flooded破洞浸水14.opened开口15.bent弯曲16.canted倾斜17.buckled皱折18.warped翘起，翘曲19.indented (dented)凹痕，凹陷（指船壳板在两档肋位间的凹陷）20.set in 凹陷（指船壳板较大面积的凹陷）21.waved波曲22.curled 卷曲（指绳索）23.rumpled 褶皱（指垫片）24.bulged 鼓起，凸出25.collapsed 倾陷，倾倒26.ruptured毁损27.torn off撕破torn拉脱28.pierced刺破29.peeled 剥皮（油第 38 页共 45 页漆剥落）30.burst 爆破（指高压管路）31.blown off (packing)吹脱32.distorted 扭曲，歪扭33.engine break-down因故障机器突然停车E.Corrosion, seizing,choking etc.1.corrosion腐蚀2.wasted耗油3.deteriorated蚀薄4.thinned变薄5.pitted麻点6.eroded侵蚀7.rusted生锈8.rotten （木、橡胶）腐烂、腐坏9.decayed （电缆）腐烂、腐坏10. aerated（橡胶、电缆）腐烂、腐坏11. aged老化12. seized咬住13. seized by corrosion锈死14. stuck （粘）咬住15. rust-jammed锈轧16. fouled拥塞17. clogged堵塞（常指管子的堵塞）18. blocked第 39 页共 45 页阻塞19. gagged塞口20. foul & dirty闭塞21. blanked封没22. plugged闭塞23. choked 卡住，阻塞F.Wear, loose, clearanceetc.1.Loose松动2.starting（铆钉）松动3.slack松动slack back松出4.worn磨损5.worn cut evenly均匀磨损6.worn cut unevenly不均匀磨损7.worn on one side单边磨损8.worn outsymmetrically 对称磨损9.distorted （轴线弯曲并扭转）扭曲10.sprung（铆钉）扭歪11.twisted （轴线未弯、纯扭转）扭转12.excess clearance间隙过大13.excess backlash齿隙过大14.excess vibration振动过大15.excess noise level噪音过大第 40 页共 45 页16.loose engagement啮合太松17.loose connection接头松动18.tooth齿worn out 磨损chopped off 崩缺fractured折断19.knocking敲击knocking cylinder 敲缸knocking valve gear 伐件敲缸knocking bearing 轴承敲缸20.bearing metal轴承合金detached脱壳cracked开裂wiped铺铅belted熔化oil groove blocked 油槽堵塞21.out off roundness失圆22.out off alignment拉线不直23.off-centering偏心24.deflected偏斜G.Burning, heating, etc.1.Sparking火花2.arcking (arcing)电弧mutator第 41 页共 45 页整流器scored拉痕burnt烧坏worn 磨耗，磨损uneven不平sparking火花blackened发黑rough粗糙mica undercut弧坑4.brush set incorrectly碳刷安装不正确5.scorched烤焦6.coked结焦7.charred结碳8.overheated过热9.broken down击穿10. short-circuit短路11. setting incorrect 整定值不正确12. tripped incorrect脱扣不正常13. batteriescompletely discharged（电）完全发光undercharged未充满overcharged充电过量dry water水干A. Remove, crop etc.1.Removed第 42 页共 45 页拆下2.removed & replaced拆装3.removed, faired &replaced拆装拷平4.cropped & renewed割换（管、板、栏杆）5.partly renewed部分换新6.partly cropped &renewed 部分割换7.cut off割除8.faired拷平9.faired on原地拷平10.faired in place原地拷平11.straightened拷直、校直12.dismantle 拆卸（某一零件）13.disassembled拆散（解体）14.stripped 拆除（某一部件）15.unshipped拆下16.disconnected 断开（线、管接头）17.opened打开18.lifted抬升、举起19.jacked 顶起（用千斤顶顶起）20.replaced (by, with)换用21.patch贴补B.Fit, scrape, grind etc.1.fitted & scraped拂刮2.fitted & ground拂磨第 43 页共 45 页3.scraped & ground刮磨4.made to fit 拂合（装配好）5.run to fit 跑合（运动磨合）6.ground round磨圆7.ground smooth磨光8.ground & reamed磨绞9.bored round镗圆10.planed smooth刨光11.polished抛光12.machined光车13.skimmed光刀14.finish machined精加工15.rough machine粗加工C.Re-metal, adjust,check etc1.Remetalled重浇白合金2.re-babbitted重浇白合金（专指巴氏合金）3.pulled out拉出4.drawn out抽出5.taken out取出6.adjusted调整，校正adjusted for alignment 校正拉线adjusted true 校正拉线adjusted for clearance第 44 页共 45 页校正间隙adjusted for centering 校中adjusted for deflection 校偏7.checked检查checked for roundness 检查圆度checked for insulation resistance 检查绝缘电阻checked for centering检查中心位置checked for alignment 检查拉线checked for clearance 检查间隙8.cleaned清洁9.wire-scrubbed 钢丝刷（除锈）10.chipped & scraped拷锈（油漆）11.measured & recorded测量并记录12.logged (hourly)记录（小时）D.weld, rivet, wind etc.1.repaired by welding电焊修理2.welded补焊、焊接3.closed up by welds（面积、深度、高度较大）焊补4.built up by welds堆焊5.plug welded塞焊6.spot welded点焊7.butt welded对接焊8 tackweld 点焊、平头焊、定位焊第 45 页共 45 页。