DATA MAN 8600参数

COGNEX®DataMan™ 100 Verifier Quick Reference GuideViewing and Saving Data4Calibration and Verification3Preparing the Reader2Hardware Installation1DataMan 100 Verifier Kit ContentsThe DM100-100V-00 reader-only kit contains these items:Documentation andCD-ROMOverviewThe DataMan 100 Verifier performs symbol and code quality verification following AIM DPM Guidelines and supporting ISO15415 and AS9132 Install PC Software and Connect Verifier1. Install the DataMan software on your PC. (Insert the CD-ROM and follow the on-screen 11Click Results Display13244Mark the position of the reader on the vertical slide, then remove the carrier from the slide.7Re-mount the carrier at the position marked in step 4.Calibrate the DataMan 100You have to calibrate the DataMan 100 regardless of which kit you use. 1Calibrate the DataMan 100Wait for the calibration process to finish. The Setup tool will indicate when the DataMan reader is calibrated:Code Quality On iconCopyright © 2010 Cognex Corporation All Rights Reserved. This document may not be copied in whole or in part, nor transferred to any other media or language, without the written permission of Cognex Corporation. The hardware and portions of the software described in this document may be covered by one or more of the U.S. patents listed on the Cognex web site / patents.asp. Other U.S. and foreign patents are pending. Cognex, the Cognex logo, and DataMan are trademarks, or registered trademarks, of Cognex Corporation. 。

AT-8600系列可堆叠三层交换机AT-8624T/2M10/100TX 端口 x 24 + 扩展插槽 x 2AT-8624POE10/100TX POE 端口 x 24 + 扩展插槽 x 2AT-8648T/2SP10/100TX 端口 x 48 + 10/100/1000T 端口x 2 + Combo SFP 插槽 x 2产品特性：z AT-8624T/2M 和AT-8624POE ：11.8 Gbps 交换矩阵, 6.6Mpps 转发速率 z AT-8648T/2SP ：23.6 Gbps 交换矩阵，10.1Mpps 转发速率z L2/L3/L4+的QoS 服务质量z 端口带宽限制，精度为进64K 、出1Mbps z 线速L2/L3/L4+数据包过滤 z 利用通用端口可堆叠至9台 z 支持RIP v1/v2 z 支持OSPF v2 z 支持VRRP z支持802.1xz 支持SSH 和SSL 安全管理 z Radius/TACACS+安全认证 z广播风暴控制z 支持SNMPv1/v2c/v3z 基于MAC 地址的端口安全性 z 支持GVRP ，GARP z 255个VLAN z Protected VLANz IGMP ，IGMP snooping ，IGMP proxy ，MVR z 8K MAC 地址表 z 802.3ad 链路聚合 z 802.1w Rapid STP z 支持冗余电源 z MSTPAT-8600系列交换机是安奈特公司推出的一款高性价比的三层快速以太网交换机，可以为网络边缘提供较高安全保障和智能的流量控制，同时兼具路由功能和增强的堆叠特性可以保护用户投资，适应网络快速增长的需求。

AT-8600系列交换机是一款专为大型企业高需求用户、中小型网络以及校园网络设计的高性能边缘/接入交换机。

用户可以受益于其智能的L2/L3/L4+控制，保障音视频等多媒体数据的传输。

凭借其丰富的QoS 功能，可以提供L2/L3/L4+的智能流分类、带宽限制、Diffserv 以及硬件ACL 访问控制，此款交换机也成为了多用户、多业务的运营商边缘交换机首选。

DataMan®360Series Quick Reference Guide04/26/2017Version:5.7.0.361PrecautionsLASER LIGHT,DO NOT STARE INTO BEAM:CLASS2PRODUCT FAILURE TO FOLLOW THESE INSTRUCTIONS CAUSE SERIOUS INJURYl CAUTION-Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiationexposure.l Do not attempt to service or repair this product--return it to Cognex for service.l Do not permit anyone other than Cognex Corporation to service,repair,or adjust this product.l Do not attempt to open or modify this device except as described in this document.l Do not direct or reflect laser light toward people or reflective objects.l Do not operate this device if it is damaged or if the covers or seals are missing or damaged.l IP protection is ensured only when all connectors are attached to cables or shielded by a sealing cap.This Laser Product is designated as Class2during all procedures of operation. Wavelength650nmLaser Power for classification<1mWBeam Diameter<3mm at apertureDivergence<1.5mradProduct Overview1Laser aimer2Illumination LED clusters3External illumination mounting point 4Mounting holes(M3x5mm)5Indicator light ring6Trigger button7Power8Train status9Read/no-read indicator10Network11Error12Peak meter13Tuning button14Ethernet15SD card slot16External light control17Power,I/O,and RS232DataMan360AccessoriesLENS OPTIONS AND COVERS10.3mm M12lens with locking(DM300-LENS-10)and10.3mm IR M12lenswith locking(DM300-LENS-10-IR)Liquid lens module and pre-focused10.3mm or10.3mm IR M12lens withwrench(DM300-LENS-10LL),(DM300-LENS-10LL-IR)19mm liquid lens module(DM300-LENS-19LL)16mm M12lens with locking(DM300-LENS-16)24mm liquid lens module(DM360-LENS-24LL)25mm M12lens with lens spacer and hex wrench(DM300-LENS-25)(alsorequires Extension kit)Extension kit(DM300-EXT)DM500C-Mount cover(DM500-CMTLC-000)(use with HPIA)DM500Lens cover extender(DM500-LNSEXT-000)Blue(CKR-BP470),red(CKR-BP635),green(CKR-BP525),orange(CKR-BP590)bandpass filtersClear lens cover(DM300-CLCOV)Clear lens cover with white LED illumination(DM300-CLCOV-WHI)Diffuse lens cover with red LED illumination(DM300-DLCOV-RE),with blue LED illumination(DM300-DLCOV-BL),with IR LED illumination(DM300-DLCOV-IR),Polarizer lens cover with red LED illumination(DM300-PLCOV-RE)EXTERNAL LIGHTS(RED LED)AND HIGH POWER ILLUMINATIONSRing Light(CLRR-R7030G1CLR)Back light(CLRB-F100100G1)Coaxial(DOAL)light(CLRO-K5050G1)Spot light(CLRS-P14G1)Dark-field light(CLRD-D120G1)Red narrow(DM30X-HPIA-625)or wide(DM30X-HPIA-625-W)White narrow(DM30X-HPIA-WHI)or wide(DM30X-HPIA-WHI-W)Blue narrow(DM30X-HPIA-470)or wide(DM30X-HPIA-470-W)Infrared narrow(DM30X-HPIA-IR)or wide(DM30X-HPIA-IR-W)Connection cable24V,I/O,RS-232(CCB-M12x12Fy-xx)(y straight/angled,xx specifies length),and(CCBL-05-01)Power and I/O breakout cable,M12-12(CCB-PWRIO-xx)(straight,xx specifies length:5m,10m,15m),(CCB-PWRIO-xxR)(angled,xx specifies length:5m,10m,15m)Connection cable RS-232(CCB-M12xDB9Y-05)Ethernet M12to RJ45cable(CCB-84901-y00x-xx)(y straight/angled,x-xx specifies length)External light cable(CCB-M12x4MS-xxx)(xxx specifies length)I/O extension cable,5m straight(CKR-200-CBL-EXT)Laser aimer(DM300-AIMER-00)(use with HPIA)24V power supply(ACC-24l)or(PS-KIT-1)External light mounting brackets(DM300-ELMB-xx)(xx specifies light type) (may get used in combination with DM500-BRKT-000if pivoting is required)Universal Mounting Bracket(DM100-UBRK-000)Pivot Mounting Bracket(DM100-PIVOTM-00)DimensionsField of View and Reading DistancesConnecting the ReaderInstallationInstallation procedures and specifications are presented in detail in the DataMan360 Reference Manual,which is installed with the DataMan Setup Tool.From the Windows Start menu,select the following to access the manual:All Programs> Cognex>DataMan Software vx.x.x>Documentation.:All cable connectors are"keyed"to fit the connectors on thesystem;do not force the connectors or damage may occur. MountingMounting the DataMan reader at a slight angle(15°)can reduce reflections and improve performance.Use the set of mounting holes on the rear part to mount the DataMan reader.Connect the Ethernet Cable1.Connect the Ethernet cable's M12connector to the DataMan system'sENET connector.2.Connect the Ethernet cable's RJ-45connector to a switch/router or PC,asapplicable.Connect the Breakout Cable1.Verify that the24VDC power supply being used is unplugged and notreceiving power.2.Attach the Breakout cable's+24VDC and Ground to the correspondingterminals on the power supply.:Never connect voltages other than24VDC.Alwaysthe polarity shown.3.Attach the Breakout cable's M12connector to the DataMan360reader's24VDC connector.4.Restore power to the24VDC power supply and turn it on if necessary.Install Software and Documentation and Connect the ReaderFollow the steps below to connect your reader to power and network:1.Connect the I/O+RS232+24V cable to your reader.2.For a network connection,connect your reader through an Ethernet cableto your network.3.Connect the cable to a24V power supply.To configure a DataMan360reader,the DataMan Setup Tool software must be installed on a networked PC.The DataMan Setup Tool is available from the DataMan support site:/support/dataman.1.After installing the software,connect the DataMan360Series reader toyour PC.unch the DataMan Setup Tool and click Refresh.3.Select your DataMan360Series reader from the list and click Connect.DataMan360Series SpecificationsWeight165gOperating Temperature0ºC—40ºC(+32ºF—104ºF)Storage Temperature-10ºC—+60ºC(+14ºF—+140ºF)Maximum Humidity<95%(non-condensing)Environmental IP65(with cable or protection cap attached to all connectors,front cover properlyinstalled)LED Safety IEC62471:red illumination:Exempt Risk Group,blue and white illuminations:Risk Group1(Low-Risk).No further labeling is required.RS-232RxD,TxD according to TIA/EIA-232-FCodes1-D barcodes:Codabar,Code39,Code128,and Code93,Interleaved2of5,MSI,Pharma,Postal,UPC/EAN/JAN2-D codes:Data Matrix(IDMax and IDQuick:ECC0,50,80,100,140,and200),QR Code and microQR Code,MaxiCode,DotCode,Aztec Code,RSS/CSStacked codes:PDF417,MicroPDF417Discrete I/O operating limits HS Output0,1,2,3IMAX50mAR MIN@12VDC200ΩInput0(Trigger)V IH±15—±28VInput1,2,3V IL0—±5VI TYP@12VDC 2.0mA@24VDC 4.2mADataMan360Series Imager SpecificationsLimitations to C-Mount lenses:l The length of the thread may not exceed5.4mm.l The back side of the lens may not exceed beyond the C-Mount threads.Possibly a lens spacer is required.l When using the C-Mount lens cover,lens dimensions including spacer and filters may not exceed32x42mm(diameter x length).degradation,consider the following duty cycle limits above25°C(77°F): l at35°C(95°F):4%duty cycle,for example,750µs exposure and18493µs intervall at45°C(113°F):2%duty cycle,for example,350µs exposure and18093µs interval or1000µs exposure and50000µs intervalRegulations/ConformityDataMan360and362readers have Regulatory Model1AA4,DataMan363 readers have Reguatory Model1ABG and meet or exceed the requirements of all applicable standards organizations for safe operation.However,as with any electrical equipment,the best way to ensure safe operation is to operate them according to the agency guidelines that follow.Please read these guidelines carefully before using your device.Manufacturer:Cognex CorporationFCC ClassCanadianComplianceC-TickStatementUL and cULStatementLaser Safety StatementCompliance with FDA performance standards for laser products except for deviations pursuant to Laser Notice No.50,dated June24,2007.This device has been tested in accordance with IEC60825-12nd ed.,and has been certified to be under the limits of a Class2Laser device.Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.LED Safety StatementThis device has been tested in accordance with IEC62471,and red illumination has been certified to be under the limits of Exempt Risk Group,blue and white illuminations have been certified to be under the limits of Risk Group1(Low-Risk). No further labeling is required.For European Community UsersCognex complies with Directive2012/19/EU OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of4July2012on waste electrical and electronic equipment (WEEE).This product has required the extraction and use of natural resources for its production.It may contain hazardous substances that could impact health and the environment,if not properly disposed.In order to avoid the dissemination of those substances in our environment and to diminish the pressure on the natural resources,we encourage you to use the appropriate take-back systems for product disposal.Those systems will reuse or recycle most of the materials of the product you are disposing in a sound way.The crossed out wheeled bin symbol informs you that the product should not be disposed of along with municipal waste and invites you to use the appropriate separate take-back systems for product disposal.If you need more information on the collection,reuse,and recycling systems,please contact your local or regional waste administration.You may also contact your supplier for more information on the environmental performance of this product.China RoHSHazardous Substances 有害物质Part Name 部件名称Lead (Pb)铅Mercury (Hg)汞Cadmium (Cd)镉Hexavalent Chromium (Cr (VI))六价铬Polybrominated biphenyls (PBB)多溴联苯Polybrominated diphenyl ethers (PBDE)多溴二苯醚Regulatory Model 1AA4ReguatoryModel 1ABGX O O O O O This table is prepared in accordance with the provisions of SJ/T 11364.这个标签是根据SJ /T 11364的规定准备的。

DataMan®8600Verifier Reference Manual2020March20Revision:6.1.7.1Legal NoticesThe software described in this document is furnished under license,and may be used or copied only in accordance with the terms of such license and with the inclusion of the copyright notice shown on this page.Neither the software,this document,nor any copies thereof may be provided to,or otherwise made available to,anyone other than the licensee. Title to,and ownership of,this software remains with Cognex Corporation or its licensor.Cognex Corporation assumes no responsibility for the use or reliability of its software on equipment that is not supplied by Cognex Corporation. Cognex Corporation makes no warranties,either express or implied,regarding the described software,its merchantability,non-infringement or its fitness for any particular purpose.The information in this document is subject to change without notice and should not be construed as a commitment by Cognex Corporation.Cognex Corporation is not responsible for any errors that may be present in either this document or the associated software.Companies,names,and data used in examples herein are fictitious unless otherwise noted.No part of this document may be reproduced or transmitted in any form or by any means,electronic or mechanical,for any purpose,nor transferred to any other media or language without the written permission of Cognex Corporation.Copyright©2020.Cognex Corporation.All Rights Reserved.Portions of the hardware and software provided by Cognex may be covered by one or more U.S.and foreign patents,as well as pending U.S.and foreign patents listed on the Cognex web site at:/patents.The following are registered trademarks of Cognex Corporation:Cognex,2DMAX,Advantage,AlignPlus,Assemblyplus,Check it with Checker,Checker,Cognex Vision for Industry, Cognex VSOC,CVL,DataMan,DisplayInspect,DVT,EasyBuilder,Hotbars,IDMax,In-Sight,Laser Killer,MVS-8000, OmniView,PatFind,PatFlex,PatInspect,PatMax,PatQuick,SensorView,SmartView,SmartAdvisor,SmartLearn, UltraLight,Vision Solutions,VisionPro,VisionViewThe following are trademarks of Cognex Corporation:The Cognex logo,1DMax,3D-Locate,3DMax,BGAII,CheckPoint,Cognex VSoC,CVC-1000,FFD,iLearn,In-Sight (design insignia with cross-hairs),In-Sight 2000,InspectEdge,Inspection Designer,MVS,NotchMax,OCRMax,PatMax RedLine,ProofRead,SmartSync,ProfilePlus,SmartDisplay,SmartSystem,SMD4,VisiFlex,XpandPortions copyright©Microsoft Corporation.All rights reserved.Portions copyright©MadCap Software,Inc.All rights reserved.Other product and company trademarks identified herein are the trademarks of their respective owners.Table of ContentsLegal Notices2Table of Contents3 Symbols4 8600Series Handheld Verifier Kit Contents5Data Matrix Symbol Quality Verification6 Upgrading a Device for Verification6Getting Started7 Stand-off7 Stand-off Installation7 Calibration8 Code Quality10 Verification10 Formatting Output Data10Verification Configuration12 Saving the Setup12 Code Quality Configuration Codes12Precautions13SymbolsThe following symbols indicate safety precautions and supplementalinformation:WARNING:This symbol indicates a hazard that could cause death,serious personal injury or electricalshock.CAUTION:This symbol indicates a hazard that could result in property damage.8600Series Handheld Verifier KitContents8600verifierstand-off Calibration card (stored in protectivesleeve)This documentWARNING :LASER LIGHT,DO NOT STARE INTO BEAM:CLASS 2LASER PRODUCT FAILURE TO FOLLOW THESE INSTRUCTIONS MAY CAUSE SERIOUS INJURYData Matrix Symbol Quality VerificationDataMan8600Verifier handheld verifiers ensure that a Data Matrix symbol meets the AIM DPM(Direct Part Mark)/ISO/IEC TR29158Quality Guideline.The DataMan8600Verifier handheld verifiers provide:l Contract Compliance:The DataMan8600Verifier software,integrated lighting,and fixed optics meet the AIM-DPM/ISO/IEC TR29158Quality Guideline.l System Calibration:The DataMan8600Verifier verifier includes a certified calibration card necessary to calibrate the reader.Upgrading a Device for VerificationIf you are upgrading a previously purchased DataMan8600Verifier reader to be used as a verifier,your reader must be using firmware version5.4.4or newer.To update the firmware:1.Connect your reader to the DataMan Setup Tool.2.Choose System>Update Firmware.3.Select the file DM8600_v.5.4.4.bin.gz or newer from the directory where the firmware update automaticallynavigates(Cognex\DataMan\Firmware\DM8000Series).To enable the DPM Verification feature,you must upload a feature key file to the reader:1.Connect the reader to the DataMan Setup Tool.2.Choose System>Upload Feature Key.3.Select the feature key file that you received from Cognex.4.The reader automatically reboots after the upgrade and it is ready to use for verification.Getting StartedStand-offThe stand-off is an accessory that consists of a plastic frame that is attachable to the device(see below). The stand-off accessory comes with one set of7mm spacers which must be screwed onto the stand-off.The reading distance the spacer provides is7mm.Stand-off Installation1.Attach the stand-off carefully to your DataMan8600Verifier reader.2.The stand-off snap-fits into the reader.Calibration1.Start the DataMan Setup Tool and connect to your reader.2.Select the Code Quality Settings task pane.3.Check the box for Verification Enabled under the Verification tab.4.Place the verifier against the calibration card with the symbol centered below the reader,and squeeze the trigger5.Continue squeezing the trigger.Calibration can take several secondsThe DataMan Setup Tool displays a graphic guide if the symbol is not precisely aligned with the reader.Adjust the position and rotation of the reader until the center of the red rectangle lies inside the green rectangle and there is no more than10degrees rotation between the symbol and the reader.The reader beeps once when calibration is complete.6.The system displays a green check box that says System Calibrated under Calibration in Verification Settings.Code QualityVerificationIn order to perform Direct Part Mark Verification,your reader must be calibrated as described in the previous section.To read symbols and view verification results,perform the following steps:1.Start the DataMan Setup Tool and connect to your reader.2.Navigate to Settings >Code Quality .3.Under the Verification Settings tab,check Verification Enabled .4.Select the Results Display task pane by clicking Code Quality under View ).5.Place the verifier against the symbol and squeeze the trigger.The symbol must be centered within the field ofview,and the reader must be perpendicular to the surface containing the symbol and at the correct rotation.If the reader is out of position,the DataMan Setup Tool displays thisguide:The verifier stand-off must be used to ensure correct symbol presentation and lighting requirements for the AIM-DPM /ISO/IEC TR 29158Quality Guideline.6.Move the reader until the center of the red rectangle lies within the green target rectangle.The reader beeps toindicate that the symbol has been read and verified.Formatting Output DataUse the Data Formatting task pane of the DataMan Setup Tool to construct a customized output string each time you read and verify a symbol.This allows the verifier to return Code Quality results when connected to a third-party application instead of the DataMan Setup Tool.In addition to standard formatting,the DataMan Setup Tool supports the use of Perl-Style Regular Expression features in Advanced mode.After verification,when connected to the DataMan Setup Tool,you can configure the Code Quality results be saved by enabling Report Storage under the Data Logging task pane.Code Quality results can be sent from the reader by configuring the output format in the Standard Formatting task pane. The reader does not have to be connected to the DataMan Setup Tool to send Code Quality results.Verification ConfigurationSaving the SetupOnce you have configured your reader with the settings you want it to use,choose System>Save Settings to save the configuration or click the Save Settings icon on the top icon row.Use the Backup feature to save the configuration to a directory on the PC.A saved configuration can be opened later and uploaded to any reader,allowing multiple readers to use the same configuration settings.Code Quality Configuration CodesPrecautionsTo reduce the risk of injury or equipment damage,observe the following precautions when you install the Cognex product:l Route cables and wires away from high-current wiring or high-voltage power sources to reduce the risk of damage or malfunction from the following causes:over-voltage,line noise,electrostatic discharge(ESD),power surges,or other irregularities in the power supply.l Changes or modifications not expressly approved by the party responsible for regulatory compliance could void the user’s authority to operate the equipment.l Ensure that the cable bend radius begins at least six inches from the connector.Cable shielding can be degraded or cables can be damaged or wear out faster if a service loop or bend radius is tighter than10X the cable diameter.l This device should be used in accordance with the instructions in this manual.l All specifications are for reference purposes only and can change without notice.Copyright©2020 Cognex Corporation.All Rights Reserved.。

康耐视手持式读码器DataMan 8600
佚名
【期刊名称】《物流技术与应用》
【年(卷),期】2014(0)10
【摘要】全球机器视觉领域的领导者康耐视公司近日推出最新的DataMan。

8600系列手持式直接部件标识（DPM）读码器。

该产品将经过业界测试的
2DMax＋TM算法和获得专利的康耐视Ultra LightTM技术相结合，可读取最棘手的各种材料表面的直接部件标识（DPM）代码。

【总页数】1页(P157-157)
【关键词】读码器;手持式;机器视觉;材料表面;领导者;M算法;标识;部件
【正文语种】中文
【中图分类】TP391.41
【相关文献】
1.康耐视DataMan®8050系列手持式读码器 [J],
2.新一代康耐视DataMan手持式ID读码器 [J],
3.康耐视推出DataMan8050系列读码器——全新的DataMan 8050手持式读码器拓展了DataMan的应用范围 [J], 无;
4.康耐视提供最广泛的基于图像的ID读码器—DataMan700手持式读码器提供完全可信赖的读码功能，可应用于任何代码、任何表面、任何打码方式 [J], 无
5.康耐视：新一代DATAMAN手持式ID读码器 [J],
因版权原因，仅展示原文概要，查看原文内容请购买。

DataMan®503Quick Reference Guide2020April14Revision:6.1.6SR1.10PrecautionsTo reduce the risk of injury or equipment damage,observe the following precautions when you install the Cognex product:l Route cables and wires away from high-current wiring or high-voltage power sources to reduce the risk of damage or malfunction from thefollowing causes:over-voltage,line noise,electrostatic discharge(ESD),power surges,or other irregularities in the power supply.l Changes or modifications not expressly approved by the party responsible for regulatory compliance could void the user’s authority to operate theequipment.l Ensure that the cable bend radius begins at least six inches from the connector.Cable shielding can be degraded or cables can be damaged orwear out faster if a service loop or bend radius is tighter than10X the cablediameter.l This device should be used in accordance with the instructions in this manual.l All specifications are for reference purposes only and can change without notice.1External illumination mounting point 2Mounting holes(M3x5mm)3Trigger button4Power5Train status6Good/bad read7Network8Error9Tuning button10Peak meter11Synchronized Acquisition12RS-23213External light control14Ethernet15Power I/O16mm,25mm and35mm lens(LEC-CFFxx-F8)(xx specifies focal length)Connection cable24V,I/O(CCBL-05-01)Ethernet M12to RJ45cable(CCB-84901-y00x-xx)(y straight/angled,x-xx specifies length)External light cable(CCB-M12x4MS-xxx)(xxx specifies length)I/O extension cable,5m straight(CKR-200-CBL-EXT)RS-232M8to SUB-D cable(CCB-M8X4-xx)Synchronization Cable(DM503-SYNC-012-1.2meter,DM503-SYNC-05-5 meter)Xpand15(DMA-FOVE-15)Xpand25(DMA-FOVE-25)SVL Light Bar(IVSL-YLW300-xxx)DM503high power illumination(DM503-HPIA-xxx)Field of View and Reading Distances16mm lens for1D codes(green)25mm lens for1D codes (blue)35mm lens for1D codes(red)Perform the following steps:1.Mount the reader.2.Connect the Ethernet cable to a computer or a switch.3.Connect the breakout cable.For information on the cable pinout and wire colors,see section Connections,Optics and Lighting in the DataMan503Reference Manual.Installation procedures and specifications are presented in detail in the DataMan®503Reference Manual,which is installed with the DataMan Setup Tool.From the Windows Start menu,select the following to access the manual:All Programs> Cognex>DataMan Software vx.x.x>Documentation.:All cable connectors are"keyed"to fit the connectors on thesystem;do not force the connectors or damage may occur.Connect the ReaderFollow the steps below to connect your reader to power and network:1.Connect the I/O+RS232+24V cable to your reader.2.For a network connection,connect your reader through an Ethernet cableto your network.3.Connect the cable to a24V power supply.To configure a DataMan503reader,the DataMan Setup Tool software must be installed on a networked PC.The DataMan Setup Tool is available from the DataMan support site:/support/dataman.1.After installing the software,connect the DataMan503reader to your PC.unch the DataMan Setup Tool and click Refresh.3.Select your DataMan503reader from the list and click Connect.Weight1602gOperatingTemperature0ºC—45ºC(32ºF—113ºF)StorageTemperature-10ºC—60ºC(-14ºF—140ºF)MaximumHumidity<95%(non-condensing)RS-232RxD,TxD according to TIA/EIA-232-FCodes1-D barcodes:Codabar,Code39,Code128,and Code93,Interleaved2of5,MSI,Pharma, GS1DataBar,Postal,UPC/EAN/JAN2-D barcodes:Data Matrix(IDMax:ECC0,50,80,100,140,and200;IDQuick:ECC200),QR Code and microQR Code,RSS/CS,PDF417,MicroPDF417Discrete I/O operating Limits HS Output0,1I MAX@24VDC50mAR MAX@12VDC150Ω@24VDC470ΩInput0(Trigger)Input1V IL0—±7VI TYP@12VDC 2.0mA@24VDC 4.2mAPower Supply Requirements 24V+/-10%Maximum current:500mA(at25ºC)Maximum power:18W(external lights)Ethernet Speed10/100/1000Duplex Mode Full duplex or half duplexThe DataMan503series meets or exceeds the requirements of all applicable standards organizations for safe operation.However,as with any electrical equipment,the best way to ensure safe operation is to operate them according to the agency guidelines that follow.Please read these guidelines carefully before using your device.CanadianComplianceC-TickStatementUL and cULStatementFor European Community UsersCognex complies with Directive2012/19/EU OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of4July2012on waste electrical and electronic equipment (WEEE).This product has required the extraction and use of natural resources for its production.It may contain hazardous substances that could impact health and the environment,if not properly disposed.In order to avoid the dissemination of those substances in our environment and to diminish the pressure on the natural resources,we encourage you to use the appropriate take-back systems for product disposal.Those systems will reuse or recycle most of the materials of the product you are disposing in a sound way.The crossed out wheeled bin symbol informs you that the product should not be disposed of along with municipal waste and invites you to use the appropriate separate take-back systems for product disposal.If you need more information on the collection,reuse,and recycling systems,please contact your local or regional waste administration.You may also contact your supplier for more information on the environmental performance of this product.China RoHSHazardous Substances 有害物质Part Name 部件名称Lead (Pb)铅Mercury (Hg)汞Cadmium (Cd)镉Hexavalent Chromium (Cr (VI))六价铬Polybrominated biphenyls (PBB)多溴联苯Polybrominated diphenyl ethers (PBDE)多溴二苯醚DM503X O O OOOThis table is prepared in accordance with the provisions of SJ/T 11364.这个标签是根据SJ /T 11364的规定准备的。

DataMan®8600快速参考指南2017/11/15预防措施激光，不要直视激光束：2级激光产品不遵守这些指示可能导致严重安装Cognex产品时请遵守这些注意事项，以降低受伤或设备损坏的风险︰l为了减少由于过电压、线路噪音、静电放电(ESD)、电涌或其他电源不正常原因造成的损害或故障风险，可以远离高电压电源来确定线缆电路。

l未经负责合规性一方的明确批准，擅自更改或修改可能使用户操作设备的权限失效。

l如果维修圈或折弯半径比电缆直径紧10倍，会降低电缆屏蔽效果或损坏电缆。

折弯半径必须在距接口至少六英寸处开始。

l应遵照本手册中的说明使用该设备。

l所有规格仅供参考，如有更改，恕不另行通知。

1UltraLight2激光瞄准器3触发器（按住读码）4通信模块插入点5指示灯6挂绳钩7扩展的读码尝试按钮8RS-232连接9USB连接10电源插头（24伏，最大1511备用电源连接器（24上标有极性）串行/USB滑件(DMCM-SERIALM-00)以太网滑件(DMCM-ENETM-00)蓝牙滑件(DMCM-BTM-00)无线滑件(DMCM-WLESSM-00)充电基站(DMA-CBASE-01)智能基站(DMA-IBASE-01)智能蓝牙基站(DMA-IBASE-BT-01)智能蓝牙基站(DMA-IBASE-BT-02)基站电源(DMA-24VPWR-xx)读码器电源(DM100-PWR-00)无线读码器电池(DMA-HHBATTERY-01)多电池充电器(DMA-MBC-xx)POE适配器(CPS-24V-POE1)POE适配器(CPS-24V-POE4)壁挂支架(DMA-WALL-8000-00)基站壁挂支架(DMA-IBASE-WALL-00)POE适配器(CPS-AC-POE1A-xx)支架(DM-STAND-00)橡胶衬套(DM8000-SLEEVE-00)读码器RS-232螺旋电缆，2.5米(DM8000-RS232-02)读码器RS-232工业电缆，2.5米(DM8000-RS232IND-02)读码器RS-232螺旋电缆，5米(DM8000-RS232-05)USB螺旋电缆，2.5米(DM8500-USBC-02)以太网电缆，2.5米(DM8000-ECABLE-02)以太网电缆，30米(DM8000-ECABLE-30)以太网电缆，5米(DM8000-ECABLE-05)USB电缆，2.5米(DM8500-USB-00)以太网螺旋电缆，5米DM8000-ECABLEC-05*基站的RJ25(RJ12)至DSUB9电缆，5米DMA-RS232RJ-05*包括DM8000-ECABLE-X的校准电缆长度不应超过50米。

扫描头设置方法Dataman setup tool软件连接扫描头方法Dataman调试软件通过以太网对扫描头进行参数设置，在对扫描头进行参数设置前必须将扫描头IP与所连接的计算机IP设置到一个网段中，如果不知道扫描头的IP,可以通过康耐视提供的cognex explorer软件直接进行读取，或者通过强制改变扫描头IP的方法给扫描头更改一个已知的IP。

Cognex explorer直接读取：点击可执行文件后可以直接显示目前网络中已经连接的扫描头IP地址，只需将计算机IP 更改为同扫描头一个网段即可通讯。

强制更改扫描头IP:进行此操作需要获取扫描头的MAC地址，MAC地址在扫描头背面的标签上有注明。

添入MAC 地址，设置将要更改的IP地址，子网掩码，点击ok按钮，扫描头自动重启后新的IP地址即生效。

将扫描头和计算机设置为一个网段，点击软件可执行文件setup tool弹出以下画面。

从画面中可以看出已经连接的扫描头已被识别，双击相应的扫描头图标即可进入设定画面。

注：如果dataman 软件没有连接到任何扫描头，是不能进入软件进行任何设置的。

连接扫描头后进入dataman的初始画面工作模式设置快速设置相关参数设定Exposure曝光参数：默认数值200Focus焦距设定：根据实际扫描效果由PLC进行设定Trigger settings触发模式：设定为congtinuous（external）外部触发连续方式。

光源模式可以通过点击扫描头光源图标所示的led灯进行灵活配置。

码制设置点击主菜单中symbology settings，弹出以上窗口，在这里主要进行读取码制的设定，可以进行多重组合，本扫描头可以进行一维码，二维码的读取，解码方式有两种ID MAX和ID QUICK。

ID MAX解码特点：解码能力强，解码过程相对耗时。

ID QUICK解码特点：解码速度快，解码能力稍弱。

通讯设置主页面communication settings选项中设置扫描头IP地址，例子中设置为192.168.1.8，子网掩码255.255.255.0，默认网关可不填communication settings->network setting选项中按照上图进行参数设置，host address中配置的是与之通讯的PLC 系统网络模块的IP地址（192.168.1.6）和端口号（2000），client port代理端口（2000），protocol必须设置为UDP 通讯方式。