三菱电机空调通风产品说明01

Thank you for choosing our product.Please read this Owner’s Manual carefully before operation and retain it for future reference.Owner's ManualOriginal InstructionsWireless Controller YAP1F7ACCMI-26HRDC1A ACCMI-36HRDC1A ACCMI-53HRDC1A ACMI-70HRDC1A1.1 Buttons on remote controller 1.2 Introduction for icons on display screen1.Operation and introductionof remote controllerDC Inverter Free match Series Cassette Type Unit31.3 Introduction for buttons on remote controllerPress this button to turn on the unit. Press this button again to turn off the unit.ion mode.AUTO COOL DRYFANHEATadjust fan blowing angle.Under COOL or HEAT mode, press this button toWhen selecting heating mode, the air condition-er operates under heat mode. Press "" or " " button to adjust set temperature. Press "FAN" button to adjust fan speed. Press " " / " " button to adjust fan blowing angle. (Cooling only unit won't receive heating mode signal. If setting heat mode with remote controller, press ON/OFF button can’t start up the unit).When selecting auto mode, air conditioner will operate automatically according to ex-factory setting. Press "FAN" button can adjust fan speed. Press " " / " " button can adjust fan blowing angle.After selecting cool mode, air conditioner will operate under cool mode. Press "" or " " button to adjust set temperature. Press "FAN" button to adjust fan speed. Press " " / " " button to adjust fan blowing angle.When selecting dry mode, the air conditioner operates at low speed under dry mode. Under dry mode, fan speed can’t be adjusted. Press " " / " " button to adjust fan blowing angle.When selecting fan mode, the air conditioner will only blow fan, no cooling and no heating. All indicators are OFF. Press "FAN" button to adjust fan speed. Press " " / " " button to,, to , then back to Auto.ƔƔƔƔThis button is used for setting Fan Speed in thesequence that goes from AUTO,, ,, 4setting.It '" "mode.ON/OFFƔƔƔƔƔƔPress this button can select left & right swing angle.Fan blow angle can be selected circularly as below:Press this button can select up & down swing angle. Fan blow angle can be selected circularly as below:Ɣ NOTENOTEƔWhen selecting " ", air conditioner is blowingfan automatically. Horizontal louver will automat-Hold " "button above 2s to set your required swing angle. When reaching your required angle, release the button. immediately.stated above.no display position)(stops at current“ 、 、fan automatically.stated above.Ɣ Ɣno display(horizontal louvers stops at current position)When selecting " ", air conditioner is、 、 ically swing up & down at maximum angle.When selecting 、 " "、 、 、, air condition-er is blowing fan at ¿xed position. Horizontal ORXYHU ZLOO VWRS DW WKH ¿[HG SRVLWLRQPress "" or " " button once increase or d e cr-ease set temperature 1℃ (°F). Holding "" or" " button, 2s later, set temperature on remote controller will change quickly. On releasing button after setting is finished, temperature indicator on indoor unit will change accordingly.When setting T-ON, T-OFF or CLOCK, press "" or " " button to adjust time. (Refer to CLOCK, T-ON, T-OFF buttons)blowing fan at ¿xed angle. Horizontal louver will VHQG DLU DW WKH ¿[HG DQJOH"T-ON" button can set the time for timer on. After button to cancel it.pressing this button, " " icon disappears and the word "ON" on remote controller blinks. Press "" or " " button to adjust T-ON setting. After each pressing "" or " " button, T-ON setting will increase or decrease 1min. Hold "" or " "button, 2s later, the time will change quickly u ntil reaching your required time. Press "T-ON " to confirm it. The word "ON" will stop blinking. "" icon resumes displaying. Cancel T-ON: Under thecondition that T-ON is started up, press "T-O N"button to cancel it. T-OFF button"T-OFF" button can set the time for timer off. Af-ter pressing this button, " " icon disappears and the word "OFF" on remote controller blinks. Press "" or " " button to adjust T-OFF setting. 5turn to quick COOL or quick HEAT mode. " " icon is displayed on remote controller. Press this button again to exit turbo function and " " icon will disappear. If start this function, the unit will run at super-high fan speed to cool or heat quickly so that the ambient temperature approaches the preset temperature as soon as possible.After each pressing "" or " " button, T-OFF setting will increase or decrease 1min. Hold "" or " " button, 2s later, the time will change qui-ckly until reaching your required time. Press "T-OFF" word "OFF" will stop blinking. " " icon resumes displaying. Cancel T-OFF. Under the condition that T-OFF is started up, press "T-OFF"ƔƔNOTEƔPress this button, can select Sleep 1 ( 1),Sleep 2 ( 2), Sleep 3 ( 3) and cancel theƔSleep, circulate between these, after electrified, Sleep Cancel is defaulted.Sleep 1 is Sleep mode 1, in Cool modes; sleep ' 6status after run for one hour, the main unit setting temperature will increase 1 , two hours, setting temperature increased 2℃, then the unit will run at this setting temperature; In Heat mode: sleep " button within 5s to set clock time. Each pressing of "" or "" button, clock time will increas e or decrease 1 min. If hold "" or "" button , 2s later, time will change quickly. Release this button when reaching your required time. Press "CLOCK" button to confirm the time. " " icon stops blink-ing.status after run for one hour, the setting tempera- ture will decrease 1 , two hours, setting tempera-ture will decrease 2 , then the unit will run at this setting temperature.ƔSleep 2 is sleep mode 2, that is air conditioner will run according to the presetting a group of sleep temperature curve.ƔSleep 3-the sleep curve setting under Sleep mode by DIY;(1) Under Sleep 3 mode, press “Turbo” button for a long time, remote controller enters into user indi-viduation sleep setting status, at this time, the time of remote controller will display “1hour”, the setting temperature “88” will display the corresponding temperature of last setting sleep curve and blink (The first entering will display according to the initial curve setting value of original factory);(2) Adjust “△” and “▽” button, could change the corresponding setting temperature, after adjusted, press “Turbo” button for confirmation;(3) At this time, 1hour will be automatically increased at the timer position on the remote con-trol, (that are "2hours" or "3hours" or "8hours"), the place of setting temperature "88" will display the corresponding temperature of last setting sleep curve and blink;(4) Repeat the above step (2)~(3) operation, until 8 hours temperature setting finished, sleep,curve setting finished, at this time, the remote controller will resume the original timer display; temperature display will resume to original setting temperature.ƔSleep3- the sleep curve setting under Sleep mode by DIY could be inquired:The user could accord to sleep curve setting method to inquire the presetting sleep curve, enter into user individuation sleep setting status, but do not change the temperature, press "Turbo " button directly for confirmation. Note: In the above preset-ting or enquiry procedure, if continuously within 10s, there is no button pressed, the sleep curve setting within 10s, there is no button pressed, the sleep curve setting status will be automatically quit and resume to display the original displaying. In the presetting or enquiry procedure, press "ON/OFF" button, "Mode" button, "Sleep" button, the sleep curve setting or enquiry status will quit similarly.function is set, the remote controller will send the detected ambient temperature to the controller a nd the unit will automatically adjust the indoor te-mperature according to the detected temperatu re. button again to cancel I FEEL function this function is set. Do not put the remote contro ller near the object of high temperature or low temper-ature in order to avoid detecting inaccurate ambie-nt temperature.When I FEEL function is turned on, the remote controller should be put within the a reawhere indoor unit can receive the signal sent bythe remote controller.Ɣ8ȭ heating functionƔƔƔNOTENOTEƔƔƔPress this button to turn off display light on indoor unit. " " icon on remote controller disappears. Press this button again to turn on display light. " " icon is displayed.7Under heat mode, press "TEMP" and "CLOCK" buttons simultaneously to start up or turn off 8ȭ ȭ" will be shown on remote controller, and the air conditioner keep the heating status at 8ȭ. Press "TEMP" and "CLOCK" buttons simulta-neously again to exit 8ȭ heating function.Press this button, you can see indoor set tempera-ture, indoor ambient temperature on indoor unit' s display. The setting on remote controller is select-ed circularly as below:Energy-saving function1.4 Function introduction for combination buttons''t''t oper-ƔNOTENOTEƔ Under 8ȭ' Under 8ȭ't be ' ȭ't operate at the same time. If 8ȭ heating function has been set ȭ heat mode, start up the 8ȭ heating function will cancel sleep function.Under ȯwill display 46ȯ heating.Press " WiFi " b utton to turn on WiFi function, "WiFi " icon will be displayed on the remote controller;Hold " WiFi " button for 5s to turn off WiFi function and " WiFi " icon will disappear.Under off status, press "MODE" and " WiFi " buttons simultaneously for 1s, WiF i module will restorefactory settings.Press this button to turn on or turn off the health and scavenging functions in operation status.Press this button for the first time to start scaveng-ing function; LCD displays " ". Press the button for the second time to start health and scaveng-ing functions; LCD displays " " and " ". Press this button for the third time to quit health and scavenging functions simultaneously. Press the button for the fourth time to start health function; LCD display " ". Press this button again to repeat the operation above.Under cooling mode, press "TEMP" and "CLOCK" buttons simultaneously to start up or turn off ener-gy-saving function. When energy-saving function is started up, "SE" will be shown on remote con-troller, and air conditioner will adjust the set tem-perature automatically according to ex-factory setting to reach to the best energy-saving effect. Press "TEMP" and "CLOCK" buttons simultane-ously again to exit energy-saving function.81. 2. 3. 4. Fig.1Reinstall the cover (as shown in Fig 2④).1.5 Replacement of batteries in remote controllerFig.2Lift the cover along the direction of arrow (as shown in Fig 1①).Child lock functionTemperature display switchover functionTake out the original batteries (as shown inFig 1②).Place two 7# (AAA 1.5V) dry batteries, and makesure the position of “ + ” polar and “ - ” polar is correct (as shown in Fig 2③).Under OFF status, press "" and "MODE" buttons simultaneously to switch temperature display between ȭ and ȯ.Press "" and "" simultaneously to turn on or turn off child lock function. When child lock func-tion is on, " " icon is displayed on remote control-ler. If you operate the remote controller, the " " icon will blink three times without sending signal to the unit.during operation.When you don ' 's66129937831。

This guide provides simple advice for both installers and residents looking to purchase a heat pump, air conditioning unit, or other exterior mechanical system.It will help you to:• determine an optimum outdoor location • select a quiet heat pump system • properly maintain your heat pump • control and prevent noise travelCITY OF VANCOUVER NOISE BYLAWThe City of Vancouver Noise Control By-Law #6555 has been protecting residents from excessive noise since its inception in 1989. This bylaw has residential noise limits depending on the time of day.WHAT ARE THE LIMITS INTHE RESIDENTIAL NEIGHBOURHOODS?HOW TO SELECT A HEAT PUMP1. SELECT A QUIET UNITMost manufacturers will specify a ‘sound power rating,’ a lab-tested decibel dB(A) measurement of the sound generated by a heat pump at full capacity. Most quality models are around 60 dB(A) while newer ‘ultra-quiet’ models are achieving lower ratings.These mechanical ratings are different than the Noise Bylaw which specifies a ‘sound pressure rating’ measured with a noise meter at the property line.That’s why properly locating the unit is critical to achieving a no-complaint system.WHAT HEAT PUMPS ARE THE QUIETEST?Look for models that have the lowest decibel rating, as well as the following features:• Variable speed fans and compressors • Soft start and stop functions• Nighttime/low sound modes • Insulated compressors55dB45dB7 am7 am10pmHEAT PUMPS & NOISEA NEIGHBOURLY INSTALLATION GUIDEWhat you need to know in order to have a smooth, nuisance-free heat pump installationpage 1 of 22. SELECT PROPERLY SIZED EQUIPMENTThe contractor should select the appropriately sized system based on the space that is to be heated/cooled. An oversized unit may ‘short cycle’ i.e. turn on and off more than necessary. This can result in excess noise and can reduce the life of the system.Consider other energy efficient improvements with your heat pump installation. A less leaky house with more insulation requires less energy to heat and cool, and could help further reduce the size of the unit needed.LOCATING THE HEAT PUMPMost noise complaints are a result of locating the outdoor unit facing, or too close to neighbouring windows, bedrooms or living areas. Consider the following unit placement to reduce noise travel:1. Locate as far away from the property line as possible.your heat pump. You may need to install a barrier if your unit can only be installed in a sensitive location.4. Mount the unit on the ground.Install the unit on a solid base such as a concrete pad or block, with rubber pads or dampeners to further minimize vibration. Wall-mounted units are generally higher which could allow for easier unimpeded noise travel. 5. Ensure sufficient air flow clearance.While locating the unit underneath a deck, patio, or in a dedicated outdoor mechanical space can be a good option, heat pumps require access to clear outdoor air flow to maintain high efficiencies. Follow the manufacturer’s instructions for best practices. 6. Consider acoustic barriers if a noise issue persists.Heat pumps generate both high and low frequency noise.June 2020 20-104• “whirring”• your unit).COMPRESSOR• High frequency sounds are readily reduced by structures, but lower frequencies may penetrate structures unless they are reduced at the source. Acoustic barriers or acoustic treatment may be necessary to further reduce noise issues.selection criteria with them, and ensure the details are in writing before signing a contract.By considering these recommendations, a new heat pump owner can experience many years of comfort and good neighbourly relations.FOR MORE INFORMATIONIf you have questions, please contact staff at 3-1-1 or visit vancouver.ca/heat-pumpspage 2 of 2。

使用说明书OPERATING INSTRUCTIONSMSD-LD23VD-H1SPLIT-TYPE AIR CONDITIONER分体褂壁式房间空调器SAFETY PRECAUTIONS NAME OF EACH PARTPREPARATION BEFORE OPERATION "I FEEL..."AUTO OPERATIONMANUAL OPERATION (COOL, DRY, FAN)AIR FLOW VELOCITY AND DIRECTION ADJUSTMENT LONG OPERATIONECONO COOL OPERATION(HEALTHY, COMFORT, ECONOMICAL OPERATION)TIMER OPERATION(OFF TIMER .ON TIMER)WHEN THE AIR CONDITIONER IS NOT GOING TO BE USED FOR A LONG TIME MAINTENANCECLEANING THE CATECHIN FILTERBEFORE CONTACTING THE SERVICEMAN,CHECK THE FOLLOWING AGAINWHEN YOU THINK THAT TROUBLE HAS OCCURED INSTALLATION, RELOCATION AND INSPECTION SPECIFICATIONSADVANCED AND EVER ADVANCINGMITSUBISHI ELECTRIC警告注意CAUTIONWARNING 安全事项各部件名称操作前的準备工作“I FEEL …”(体感…)自动运转用户自己选择运转模式时(製冷·除湿·送风)风速·风向的调节超远送风凉感运转(健康·舒适·省电运转)定时器设定(定时关·定时开)长期不使用时室内机组的清理茶精清新网的清理在请维修人员之前，请再次检查以下项目当您认为「发生故障?」时安装·移机·检查技术性能表5 7 911131516171819202122242526303234363840414243444546474950文中所用“符号”的意思如下。

Fig. 1 —Size 36KFig. 2 —Sizes 48K and 58KNOTE: Read the entire instruction manual before starting the installation.NOTE: Images are for illustration purposes only. Actual models may differ slightly.TABLE OF CONTENTSSAFETY CONSIDERATIONS (2)PARTS LIST (3)SYSTEM REQUIREMENTS (4)WIRING (4)DIMENSIONS (5)CLEARANCES (7)INSTALLATION TIPS (8)ELECTRICAL DATA (10)CONNECTION DIAGRAMS (10)SYSTEM VACUUM AND CHARGE (10)START-UP (11)OUTDOOR UNIT DIAGNOSTIC GUIDES (12)Installation InstructionsSpecifications subject to change without notice.SAFETY CONSIDERATIONS Installing, starting up, and servicing air- conditioning equipmentcan be hazardous due to system pressures, electrical components,and equipment location (roofs, elevated structures, etc.).Only trained, qualified installers and service mechanics should install, start- up, and service this equipment.Untrained personnel can perform basic maintenance functions such as coil cleaning. All other operations should be performed by trained service personnel only.When working on the equipment, observe the precautions in the literature and on tags, stickers, and labels attached to the equipment.Follow all safety codes.Wear safety glasses and work gloves. Keep a quenching cloth and a fire extinguisher nearby when brazing. Use care in handling, rigging, and setting bulky equipment. Read these instructions thoroughly and follow all warnings or cautions included in literature and attached to the unit. Consult local building codes and National Electrical Code (NEC) for special requirements. Recognize safety information.This is the safety- alert symbol . When you see this symbol on the unit and in instructions or manuals, be alert to the potential for personal injury. Understand these signal words: DANGER,W ARNING, and CAUTION. These words are used with the safety- alert symbol. DANGER identifies the most serious hazards which will result in severe personal injury or death. WARNING signifies hazards which could result in personal injury or death. CAUTION is used to identify unsafe practices which may result in minor personal injury or product and property damage.NOTE is used to highlight suggestions which will result in enhanced installation, reliability, or operation.ELECTRICAL SHOCK HAZARDFailure to follow this warning could result in personal injury or death. Before installing, modifying, or servicing system, main electrical disconnect switch must be in the OFF position. There may be more than 1 disconnect switch. Lock out and tag switch witha suitablewarning label.EXPLOSION HAZARDFailure to follow this warning couldresult in death, serious personal injury,and/or property damage.Never use air or gases containing oxygenfor leak testing or operating refrigerantcompressors. Pressurized mixtures of airor gases containing oxygen can lead toan explosion.EQUIPMENT DAMAGE HAZARDFailureto follow this caution may result in equipment damage or improper operation.Do not bury more than 36 in. (914 mm) of refrigerant pipe in the ground. If any section of pipe is buried, there must be a 6 in. (152 mm) vertical rise to the valve connections on the outdoor units. If more than the recommended length is buried, refrigerant may migrate to the cooler buried section during extended periods of system shutdown. This causes refrigerant slugging and could possibly damage the compressor at start-up.2 Specifications subject to change without notice. 38MBR-03SI38MBR-03SI Specifications subject to change without notice. 3PARTS LISTTable 1 —Parts ListFig. 3 —Parts ListNOTE:- If the outdoor unit is higher than the indoor unit, prevent rain from flowing into the indoor unit along the connection pipe by making a downward arc in the connection pipe before it enters the wall to the indoor unit. This ensures that rain drips from the connection pipe before it enters the wall.- Piping and the interconnecting wiring are field supplied.- The illustration above is only a sketch. Different models may be slightly different.The following units are covered in these installation instructions.Table 2 — Unit SizesPART NO.PART NAMEQTY.1Outdoor unit1-Literature package including installation instructions and warranty1-Grommet to secure the outdoor unit (helps with vibration prevention during unit operation)4-Drain Joint 1-Drain Hose1SYSTEM TONSKBTUH VOLTAGE - PHASEOUTDOOR MODEL 336,000208/230 - 138MBRQ36A - - 3448,000208/230 - 138MBRQ48A - - 3558,000208/230 - 138MBRQ58A - - 34 Specifications subject to change without notice. 38MBR-03SISYSTEM REQUIREMENTSAllow sufficient space for airflow and service of the unit. See Fig. 6 for the required minimum distances between the unit, walls or ceilings.PipingIMPORTANT: Both refrigerant lines must be insulated separately.Table 3 contains piping information for the product covered within this document.Table 3 — Piping and Refrigerant InformationAll outdoor units have an electronic expansion valve to manage the refrigerant flow of the fan coil connected.WIRINGAll wires must be sized per NEC (National Electrical Code) or CEC (Canadian Electrical Code) and local codes. Use Electrical Data table MCA (minimum circuit amps) and MOCP (maximum over current protection) to correctly size the wires and the disconnect fuse or breakers respectively.SIZES 36 - 58 RECOMMENDEDCONNECTION METHOD FOR POWER AND COMMUNICATION WIRINGPower and Communication Wiring:The main power is supplied to the outdoor unit. The field supplied power wiring from the outdoor unit to the indoor unit consists of three (3) wires and provides the power for the indoor unit. Two wires are high voltage AC power and one is a ground wire. To minimize voltage drop, the factory recommended wire size is 14/2stranded with a ground.Communication Wiring:A separate shielded stranded copper conductor only, with a 600 volt rating and double insulated copper wire, must be used as the communication wire from the outdoor unit to the indoor unit.Please use a separate shielded 16GA stranded control wire.SYSTEM SIZE36K 48K 58K PIPINGMin. Piping Length ft(m)10(3)10(3)10(3)Standard Piping Lengthft(m)25(7.5)25(7.5)25(7.5)Max. outdoor - indoor height difference (OU higher than IU)ft(m)98(30)98(30)98(30)Max. outdoor - indoor height difference (IU higher than OU)ft(m)98(30)98(30)98(30)Max. Piping length with no additional refrigerant charge ft(m)26(8)26(8)26(8)Max. Piping Lengthft(m)213(65)213(65)213(65)Additional refrigerant charge(between Standard - Max piping length)Oz/ ft(g/m)0.32 (30)0.32(30)0.32(30)Gas Pipe (size - connection type)in(mm)5/8(16)5/8(16)3/4(19)Liquid Pipe (size- connection type)in(mm)3/8(9.52)3/8(9.52)3/8(9.52)REFRIGERANTRefrigerant Type - - R410A R410A R410A Charge AmountLbs(kg)6.72(3.05)9.26(4.2)10.19(4.62)EQUIPMENT DAMAGE HAZARDFailure to follow this caution may result in equipment damage or improper operation.Wires should be sized based on NEC and local codes.EQUIPMENT DAMAGE HAZARDFailure to follow this caution may result in equipment damage or improper operation.Be sure to comply with local codes while running wire from the indoor unit to the outdoor unit.Every wire must be connected firmly. Loose wiring may cause the terminal to overheat or result in unit malfunction. A fire hazard may also exist. Ensure all wiring is tightly connected.No wire should touch the refrigerant tubing, compressor or any moving parts.Disconnecting means must be provided and shall be located within sight and readily accessible from the air conditioner.Connecting cable with conduit shall be routed through the hole in the conduit panel.38MBR-03SI Specifications subject to change without notice. 5DIMENSIONSSize 36KFig. 4 —Size 36K Table 4 — Dimensions 36KUNIT SIZEWIDTH IN (MM)DEPTH IN (MM)HEIGHT IN (MM)L1 IN (MM)L2 IN (MM)OPERATING WEIGHT LB (KG)36K37.24 (946)16.14 (410)31.89 (810)26.50 (673)15.87 (403)136.47 (61.9)Sizes 48K and 58KFig. 5 —Sizes 48K and 58KTable 5 — Dimensions 48K and 58KUNIT SIZE WIDTH IN (MM)DEPTH IN (MM)HEIGHT IN (MM)L1 IN (MM)L2 IN (MM)OPERATINGWEIGHT LB (KG) 48K37.22 (945)15.58 (396)52.48 (1333)24.96 (634)15.90 (404)217.4 (98.6) 58K37.22 (945)15.58 (396)52.48 (1333)24.96 (634)15.90 (404)217.4 (98.6)6 Specifications subject to change without notice. 38MBR-03SI38MBR-03SI Specifications subject to change without notice. 7CLEARANCESFig. 6 — Outdoor Unit ClearancesTable 6 — Outdoor Unit Clearance DimensionsFig. 7 —Clearances for multiple unitsUNIT MINIMUM VALUEIN. (MM)A 24 (610)B 24 (610)C 24 (610)D 4 (101)E4 (101)8cm) o r more ultiple parall el range ment cm) or more on le para llel un it ementor mo re or mor e on a multip le para llel unit ar rangem ent 24in (61cm) o r more on a si ngle p arallel unit ar rangem entINSTALLATION TIPSIdeal installation locations include:Outdoor Unit• A location which is convenient to installation and not exposed to strong winds.• A location which can bear the weight of the outdoor unit and where the outdoor unit can be mounted in a level position.• A location which provides appropriate clearances (see Fig. 6).•Do not install the indoor or outdoor units in a location with special environmental conditions. For those applications, contact your Ductless representative.OUTDOOR UNIT INSTALLATIONe a rigid base to support the unit in a level position.2.Locate the outdoor unit and connect piping and wiring.Fig. 8 —High Wind InstallationMAKE REFRIGERANT PIPING CONNECTIONS (OUTDOOR UNIT) IMPORTANT: Use refrigeration grade tubing ONLY. No other type of tubing may be used. Use of other types of tubing will void the manufacturer's warranty.Do not open the service valves or remove the protective caps from the tubing ends until all connections are made.Bend the tubing with bending tools to avoid kinks and flat spots. Keep the tubing free of dirt, sand, moisture, and other contaminants to avoid damaging the refrigerant system.Avoid sags in the suction line to prevent the formation of oil traps. Insulate each tube with a minimum 3/8-in. (10 mm) wall thermal pipe insulation. Inserting the tubing into the insulation before making the connections will save time and improve installation quality.1.Remove the service valve cover, if provided with the unit.2.Cut the pipe, with a pipe cutter, at 90 degrees (see Fig. 9).3.Remove the service connection, if provided with the unit.Fig. 9 —Cut the pipe 4.Remove all the burrs from the cut cross section of the pipe avoidingany burrs inside the tubes.5.Remove the flare nuts attached to the indoor and outdoor units.6.Install the correct size flare nut onto the tubing and make a flareconnection. Refer to Table7 for the flare nut spaces.Table 7 — Flare Nut SpacingFig. 10 —Flare Nut Spacing7.Apply a small amount of refrigerant oil to the flare connection onthe tubing.8.Align the center of the pipes and/or service valve.Fig. 11 —Align Pipe Center9.Connect both the liquid and gas piping to the indoor unit.10.Tighten the flare nut using a torque wrench as specified in Table8.plete the installation.Table 8 — Tightening TorqueFig. 12 —Tighten the Flare Nut EQUIPMENT DAMAGE HAZARDFailure to follow this caution may result in equipment damage orimproper operation.In regions with snowfall and cold temperatures, avoid installing theoutdoor unit in areas where it can be covered by snow. If the outdoorunit is installed in areas where heavy snow is expected, a fieldsupplied ice or snow stand and/or field supplied-installed wind baffleshould be installed to protect the unit from snow accumulation and/orblocked air intake. Blocking the air intake may result in reducedairflow, significantly reduced performance and damage to theequipment.StrongwindOUTER DIAM. (MM)A (MM)MAX. MIN.Ø1/4”(6.35)0.05 (1.3)0.03 (0.7)Ø3/8”(9.52)0.06 (1.6)0.04 (1.0)Ø1/2”(12.7)0.07 (1.8)0.04 (1.0)Ø5/8”(15.88)0.09 (2.2)0.08 (2.0)PIPE DIAMETERINCH (MM)TIGHTENINGTORQUEFT - LB N- MØ1/4” (6.35)10 to 1313.6 to 17.6Ø3/8” (9.52)24 to 3132.5 to 42.0Ø1/2” (12.7)37 to 4650.1 to 62.3Ø5/8” (15.88)50 to 6067.7 to 81.3Flare nutCopper tubeEQUIPMENT DAMAGE HAZARDFailure to follow this caution may result in equipment damage orimproper operation.Excessive torque can break the flare nut depending on installationconditions.CAUTION8 Specifications subject to change without notice. 38MBR-03SI38MBR-03SI Specifications subject to change without notice. 9Install All Power and Interconnecting Wiring to Outdoor Units1.Mount the outdoor power disconnect.2.Run the power wiring from the main box to disconnect per NEC and local codes.3.Remove the field wiring cover from the unit by loosening the screws.4.Remove the caps on the conduit panel.5.Connect the conduit to conduit panel (see Fig.13).6.Properly connect both the power supply and control lines to the terminal block per the connection diagram for the appropriate unit capacity and voltage.7.Ground the unit in accordance with NEC and local electrical codes. e the lock nuts to secure the conduit.9.Reinstall the field wiring cover.Fig. 13 —Field WiringDrain ConnectionsInstall drains must meet local sanitation codes.Install the outdoor unit drain jointFit the seal into the drain joint, then insert the drain joint into the base pan hole of the outdoor unit. Rotate 90° to securely assemble them. Connect the drain joint with an extension drain hose to avoid condensate from draining off the outdoor unit during the heating mode.Fig. 14 —Drain JointNOTE: Images are for illustration purposes only.NOTE: Basepan built-in with multiple holes for properdraining during defrost. For applications where it is required to seal these holes, and re-direct the condensate drain, rubber plugs are available through RCD.Table 9 — Base Pan Base Rubber PlugsEQUIPMENT DAMAGE HAZARDFailure to follow this caution may result in equipment damage or improper operation.Be sure to comply with local codes while running wire from indoor unit to outdoor unit.Every wire must be connected firmly. Loose wiring may cause the terminal to overheat or result in unit malfunction. A fire hazard may also exist. Therefore, ensure all wiring is tightly connected. No wire should be allowed to touch the refrigerant tubing, compressor or any moving parts.Disconnecting means must be provided and shall be located within sight and readily accessible from the air conditioner.Connecting cable with the conduit shall be routed through hole in the conduit panel.O v OUTDOOR UNIT MODEL NUMBERPER UNIT BASE PAN BASE RUBBER PLUGS RCDPART NUMBER QUANTITY38MBRQ36A - - 312600801A00117538MBRQ48A - - 312600801A00118538MBRQ58A - - 312600801A001185Seal Base pan holeDrain jointSealBase panDrain jointEQUIPMENT DAMAGE HAZARDIn cold climates, ensure the drain hose is as vertical as possible to ensure swift water drainage. If water drains too slowly, it can freeze in the hose and flood the unit.10 Specifications subject to change without notice. 38MBR-03SIELECTRICAL DATATable 10 — Electrical Data*Permissible limits of the voltage range at which the unit will operate satisfactorily.LEGENDFLA - Full Load AmpsMCA - Minimum Circuit AmpsMOCP - Maximum Over-Current Protection RLA - Rated Load AmpsCONNECTION DIAGRAMSFig. 15 —Connection DiagramsNOTES:1.Do not use the thermostat wire for any connection between indoor and outdoor units.2.All connections between indoor and outdoor units must be as shown. The connections are sensitive to polarity and will result in a fault code.SYSTEM V ACUUM AND CHARGERefrigerant tubes and the indoor coil should be evacuated using the recommended 500 microns deep vacuum method. The alternate triple evacuation method may beused if the procedure outlined below is followed.NOTE: Always break a vacuum with dry ing Vacuum Pumppletely tighten flare nuts A, B, C, D, connect the manifold gage charge hose to a charge port of the low side service valve (see Fig. 16).2.Connect the charge hose to vacuum pump.3.Fully open the low side of manifold gage (see Fig. 17).4.Start the vacuum pump.5.Evacuate using either the deep vacuum or triple evacuation method.6.After evacuation is complete, fully close the low side of manifold gage and stop the vacuum pump operation.7.The factory charge contained in the outdoor unit is good for up to 25 ft. (8 m) of line length. For refrigerant lines longer than 25 ft. (8m), add refrigerant, up to the allowable length, as specified in the System Requirements section.8.Disconnect the charge hose from the charge connection of the low side service valve.9.Fully open service valves B and A. 10.Securely tighten the service valve caps.Fig. 16 —Service ValveFig. 17 — ManifoldOUTDOOR UNIT SIZE36K 48K 58K POWER SUPPLY208/230 - 1 - 60208/230 - 1 - 60208/230 - 1 - 60Max – Min* Oper. Voltage253 - 187253 - 187253 - 187MCA 303535MOCP505050COMPRESSORVolts- PH- Hz208/230 - 1 - 60208/230 - 1 - 60208/230 - 1 - 60RLA 8.8511.8611.86OUTDOOR FAN MOTORFLA1.21 1.17 1.17Rated HP 0.160.140.14Output1208585UNIT DAMAGE HAZARDFailure to follow this caution may result in equipment damage or improper operation.Never use the system compressor as a vacuum pump.hosepump38MBR-03SI Specifications subject to change without notice. 11Deep Vacuum MethodThe deep vacuum method requires a vacuum pump capable of pulling a vacuum of 500 microns and a vacuum gage capable of accurately measuring this vacuum depth. The deep vacuum method is the best way to assure a system is free of air and moisture (see Fig. 18).Fig. 18 — Deep Vacuum GraphTriple Evacuation MethodThe triple evacuation method should only be used when the vacuum pump is only capable of pumping down to 28 in. of mercury vacuum and the system does not contain any liquid water.Refer to Fig. 19 and proceed as follows:1.Pump the system down to 28 in. of mercury and allow the pump to continue operating for an additional 15 minutes.2.Close the service valves and shut off the vacuum pump.3.Connect a nitrogen cylinder and regulator to the system and open until the system pressure is 2 psig.4.Close the service valve and allow the system to stand for 1 hr.During this time, dry nitrogen can diffuse throughout the system absorbing moisture.5.Repeat this procedure as indicated in Fig. 19. The system will then be free of any contaminants and water vapor.Fig. 19 — Triple Evacuation MethodFinal Tubing CheckIMPORTANT: Check to be certain factory tubing on both the indoor and outdoor unit has not shifted duringshipment. Ensure tubes are not rubbing against each other or any sheet metal. Pay close attention to the feeder tubes, making sure wire ties on feeder tubes are secure and tight.START-UPTest OperationPerform a test operation after completing a gas leak and electrical safety check. See the indoor unit installation instructions and owner's manual for additional start up information.System Checks1.Conceal the tubing where possible.2.Make sure that the drain tube slopes downward along its entire length.3.Ensure all tubing and connections are properly insulated.4.Fasten the tubes to the outside wall, when possible.5.Seal the hole through which the cables and tubing pass.Outdoor Unit1.Are there unusual noises or vibrations during operation?Explain the Following Items to the Customer (with the aid of the Owner's Manual):1.Explain care and maintenance.2.Present the installation instructions to the customer.500MINUTES123456710001500LEAK IN SYSTEMVACUUM TIGHT TOO WET TIGHTDRY SYSTEM 2000M I C R O N S250030003500400045005000Copyright 2018 CAC/BDP D 3300 Riverwood Parkway Atlanta GA, 30339 Edition Date: 09/18 Catalog No. 38MBR-03SI Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations. Replaces: 38MBR-02SIOUTDOOR UNIT DIAGNOSTIC GUIDESFor ease of service, the systems are equipped with a diagnostic code display LEDs on both the indoor and outdoor units. The outdoor diagnostic is displayed on the outdoor unit microprocessor board.There may be a few error codes displayed in the indoor unit that might relate to the outdoor unit's problems. If possible, always check the diag -nostic codes displayed on the indoor unit first.The diagnostic codes displayed on the outdoor units are listed on Table 11.Table 11 — Unit Diagnostic GuidesFor additional diagnostic information, refer to the service manual.DISPLAYLED STATUSE1Communication malfunction between indoor and outdoor units.F0Protection of over - currentF1Open circuit or short circuit of outdoor ambient temperature sensor T4F2Open circuit or short circuit of condenser coil temperature sensor T3F3Open circuit or short circuit of Compressor discharge temperature sensor T5F4Outdoor unit EEPROM errorF5Outdoor fan speed has been out of control P0IPM malfunctionP1Over voltage or over low voltage protection P2High temperature protection of compressor top P3Outdoor low temperature protection P4Inverter compressor drive error P7Outdoor IGBT temperature sensor errorJ0High temperature protection of indoor coil in heating J1Outdoor temperature protection of outdoor coil in cooling J2Discharge temperature protection J3Protection of active PFC moduleJ4Communication error between control board and IPM board J5High - pressure switch protection J6Low - pressure switch protection J8AC voltage protection。

各部件名称...........................操作前的准备工作.....................“I FEEL...”（体感...）自动运转 ....选择运转模式时（製冷、除湿、製热、送风）..动态地面测温控製操作.................动态地面测温传感器的测温方向设定.....风速·风向的调节.....................睡眠模式运转.........................凉感控製运转.........................定时器运转（定时开·定时关）.........空调机长期不使用时...................维护.................................前面板的清扫.........................过滤网的清扫.........................在请维修人员之前，请再次检查以下项目.当您认为「发生故障」时...............移机·检查...........................安装安全事项.........................安装说明.............................135678910121313141414151616171720Safety precautions .....................................Part name ..................................................Preparation before operation ....................."I FEEL..." Auto Operation .........................Manual operation (Cooling, Dry, Heating,Fan) ..........................................................."MOVE EYE"CONTROL OPERATION ......AREA SETTING ........................................Air flow velocity and direction adjustmentSleep operationEcono Cool operation .......Econo Cool operation ................................Timer operation (OFF TIMER-ON TIMER) ...When the air conditioner is not used fora long time .................................................Maintenance ..............................................Front panel cleaning ..................................Filter Cleaning ...........................................Please check the following itemsbefore connecting a serviceman...............When you think trouble occurs ..................Removal and inspection ............................Safety precautions for Installation .............Installation instructions ..............................2729303233343537383939404040414242434346安装结束后，请安装人员务必在安装结算联和保修卡上按要求贴好条形码。

安装结束后，请安装人员务必在安装保修指南的制造商信息登记联和保修卡上按要求贴好条形码本空调机充注R32环保制冷剂，请在安装、使用、维修前阅读使用安装说明书，否则可能会引发火灾造成人身伤害和财产损失。

使用前，请务必详读此「安全事项」。

这里所示的注意事项，是一些有关安全的非常重要的内容，一定要遵守。

绝对禁止。

请务必按指示操作。

禁止插入手指头或棒条等。

请务必关闭电源。

文中所用“图形符号”含义如下警告禁止在电源线的中途引线或延长电源线禁止用杀虫剂·消毒剂·可燃性本空调机的安装、移机、维修必须由厂家指定的且有专业资质的人员进行操作因为若操作不当将可能引起火空调不制冷·不制热时有制冷剂泄漏的可能。

如发现制冷剂泄漏，请立即停机且打开所有门窗换气，并立即与本空调机的出售店或售后服务中心联系！和燃烧器具一起使用时，应该时常换气可能产生氧气不足的现象。

注意室内外机组下面不得堆放必须安装漏电断路器警告注意注意若不装漏电断路器，便可能有触电的危险。

禁止给电池充电或拆卸电池，禁止投入火中如果电池液沾到皮肤或衣服，请安装机器禁止在直接吹到空调机气流的地方放置动植物禁止敞开门窗，在高湿度状况下作长时间的运转禁止踩在室内/室外机组上或在上面堆放东西可能跌下受伤或机器掉落伤人。

长期不使用机器时,应关闭电源开关因堆积灰尘而有可能引起火灾和事故。

室内机组室外机组（背面·侧面）进 风 口 进风口前面板内侧导风板（左右风向）正面导风板前导风板后导风板温度传感器湿度传感器「清扫复位」键左右风向导风板上下风向导风板无线适配器〈大文字画面显示例〉请点击液晶画面，画面灯亮后开始遥控器操作。

约过30秒不进行操作的话，液晶画面会再暗掉。

液晶画面灯灭后一分钟内再点击的话会显示灯灭前的画面。

关于液晶画面（触屏画面）在菜单或设定画面中呈阴影状的是无法设定的项目，点击这些项目会显示简单的说明。

在触屏上点击显示的图标或项目即可进行操作。

FX2N-10PG 用 户 手 册用户手册 FX2N-10PGFX2N 10PG 脉冲输出模块序言本手册中的文本说明， 图表以及注释等内容都是为了指导读者能够正确地安装和操作FX2N -10PG脉冲 输出模块。

用户在安装和使用该模块之前请务必阅读并且理解手册的内容。

有关更加详尽的信息，可以参考FX2N 系列硬件手册，FX2N 系列硬件手册和FX系列可编程序控制器的 编程手册 I I 。

如果在安装 FX2N -10PG 脉冲输出模块的过程中有任何疑问的话， 请务必向有资格的以及接受过适合于安 装现场的国家标准知识的专业电气工程师咨询。

如果在使用FX2N -10PG脉冲输出模块的过程中有任何疑问的话， 请务必向最近的三菱电机的代理商咨询。

本手册发生修改时不另行通知。

FX2N -10PGFX 2N -10PGiFX2N-10PGiiFX2N 10PG 脉冲输出模块传真反馈 三菱电机在不断地致力于发展和推广全球工业自动化的新领域方面享有声誉。

可能有时本书中的一些细节部分会 被用户所疏忽。

然而， 在三菱电机持续改进的过程中， 我们热忱欢迎三菱的用户给我们提出宝贵的意见。

此页内 容就是特意为广大读者而设计， 请将您的意见填写在下表中并且回传给我们。

我们热切期待你的反馈。

传真号码： 三菱电机…. 美国 (01) 847-478-2253 澳大利亚 (02) 638-7072 德国 南非 英国 (0 21 02) 4 86- 1 12 (0 27) 11 444-0223 (01707)278-695姓名 ．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．． ．． ．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．． ．． 公司 ．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．． ．． ．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．． ．． 地点 ．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．． ．． ．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．． ．．请在下表中选择 您的手册送达时的状态如何？ 您是否会使用文件夹来保存手册？ 您如何评价手册中的给你的外观印象？ 您觉得手册中的内容是否能够理解？ □良好 □是 □整齐的 □是 □轻微损坏 □不是 □不友好的 □不算太差 □不能使用□不能理解您认为手册中最难理解的内容是什么：．．．．．．．．．．．．． ．．．．．．．．．．．．． ．．．．．．．．．．．． ．．．．．．．．．．．．． ．． ．．．．．．．．．．．． ．．． ．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．． ． 是否有不够清晰的图表? □有 □没有 如果有的话，是哪个：．．．．．．．．．．．．．．．．．．．．．．．．．．．．．． ．．．．．．．．．．．．．．．．．．．．．．．．．．．．． ．．．．．．．．．．．．．．．．．．．．． ．．．． 您认为该手册的版面设计如何？ □良好 □不算太差 □无用的 如果有您认为需要改进的地方，您认为是什么？．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．． ．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．． ．．． ． ．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．． ． ．．． ．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．． ．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．． ．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．． 您是否能够通过使用目录轻易地找到您所需要的信息， 如果可能的话请传授您的经验： ．．．．．．．．．．．．．．．．．． ．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．． ．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．． ．．．． ．．． ．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．． ．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．． ．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．． ．．．．．．．． ．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．． ．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．． 大体上您对三菱的产品手册有什么意见？．．．．．．． ．．．．．． ．．．．．．．．．．．．．．．．．． ．．．．．．．． ．．．．．．．．． ．．．．． ．．．．． ．．．．． ．． ．．．．．．．．．．．．．．．．．．．．．．．． ．．． ．．．．．．．．．．．．．．．．．．．．．．． ．．．．． ．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．． ．．．．．．．．．．．．．．．．．． ．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．． ．．．．．．．．．．．．．．．．．．．．．．．．．．．．．． ．．．．．．．．．．．．．．．．．．．．．．．．．．．．． ．．．．．．．．．．．．．． ．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．． ．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．． ．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．． ．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．．． 感谢占用您宝贵的时间来完成这份问卷调查。