GEPLC第3讲 PACsystem RX3i指令系统1

前言在工业化大生产中，随着PLC技术的普及应用，社会上对PLC技术人才的需求明显增加。

可编程序控制器简称PLC，是以微处理器为核心的工业自动控制通用装置。

它具有控制功能强、可靠性高、使用灵活方便、易于扩展、通用性强等一系列优点。

尤其现代的可编程序控制器，其功能已经大大超过了逻辑控制的范围，还包括运动控制、闭环过程控制、数据处理、通信网络等。

它不仅可以取代传统的继电一接触器控制系统，进行复杂的生产过程控制，还可以应用于工厂自动化网络。

目前PLC与CAD／CAM、机器人技术一起并称为当代工业自动化的三大支柱。

因此，PLC应用技术已成为自动化类、机电一体化等专业学生就业时必须掌握的一项技能。

本书从应用的角度出发，以GE-FANUC公司RX3i系列PLC为样机，简单介绍了其指令系统、PLC程序设计的方法与技巧、PLC控制系统的设计和调试等。

本书主要以实例形式介绍了PLC模拟量的处理、人机界面的应用等。

本书在编写时力求由浅入深、通俗易懂、淡化理论、注重应用。

全书共分3章，内容包括：GE-FANUC公司RX3i系列PLC系统特性及硬件构成，RX3i系列系列PLC的编程语言及程序结构，RX3i系列PLC控制系统设计与调试实践和PLC 应用系统设计实例。

本书由南京工程学院郁汉琪担任主编。

参加编写的有南京工程学院许其清、陈巍、王刚、熊新娟、陈兴荣、苏醒、陈国军、陈凯荣、陆欣云、程启华、、史建俊、张志伟、严奎。

由于编者水平有限，书中难免有不足和错漏之处，恳请读者批评指正。

第一篇GE－FANUC简介及基本知识一、基本知识一）硬件介绍——PAC Systems RX3i的特点PAC Systems RX3i控制器是创新的可编程自动化控制器PAC Systems家族中最新增加的部件。

它是中、高端过程和离散控制应用的新一代控制器。

如同家族中的其它产品一样，PAC Systems RX3i的特点是具有单一的控制引擎和通用的编程环境，提供应用程序在多种硬件平台上的可移植性和真正的各种控制选择的交叉渗透。

通用GE PACSystems RX3i系列PLC配置教程
PACSystems RX3i系列PLC的编程软件为“Proficy Machine Edition 7.5”。

目的是完成PLC新IP设置，通过网口完成程序下载。

一、已知PLC内设默认IP为192.168.0.100。

二、将编程电脑IP设为与PLC同网段IP，如图1。

图1
再点按钮，可见图2如下。

图2
点上面的按钮，添加100网段IP如图3，填写完毕点，结果如图4。

图3
图4
三、打开PLC程序，将Target内IP和CPU新IP设置如下图5。

图5
四、点击按钮，进行PLC连接，结果如下图6。

图6
五、PLC已连接上，为只读状态，点击变绿的手掌图案按钮，进入可编辑状态，如图7。

图7
六、点击下载按钮，设置如下图8。

图8
七、下载过程中出现如下图9提示，不用理会，点是。

图9
八、图10显示下载成功后的界面。

图10
九、以上下载完成后，PLC会试图与编程电脑连接，如下图11，但由于下载完成后，PLC的IP已经被修改为192.168.100.10，连接会不成功，这是正常的，点Cancel按钮，如下图12，点确定。

图11
图12
十、修改Target中IP如下图13。

图13
十一、重复第四至六步骤后，如下图14，点OK，即完成程序下载。

图14
全文完。

GE Fanuc 自动化可编程控制器产品PAC Systems RX3i系统手册GFK-2314June 2004杭州集益科技有限公司-您身边的GE PLC专家 0571-********目录第一章产品介绍 ............................................................................................................ 1-1 PACSystems RX3i............................................................................................. 1-2 PACSystems RX3i 性能 ...................................................................... 1-2编程和配置 ................................................................ 1-2从 Series 90-30移植到PACSystems RX3i..................................... 1-2 RX3i Systems模块................................................................................. 1-3 RX3i 模块 (IC695)................................................................................ 1-3RX3i 模块 (IC694)................................................................................ 1-4RX3i 模块 (IC694)................................................................................ 1-5用于 RX3i 系统中的系列90-30 (IC693) 模块 ....................................... 1-6用于 RX3i PAC Systems 的系列 90-30 (IC693) 模块 ................................ 1-7 不能用于R X3i系统中的系列90-30模块........................1-8背板和电源 ..................................................................... 1-10 RX3i Systems的背板........................................................... 1-11RX3i Systems的电源............................................................ 1-11 扩展系统 ......................................................................................... 1-12 使用多个扩展和远程背板.................................1-13 第二章安装 ....................................................................................................... 2-1预安前检测........................................................................................ 2-2系统布局指导 ................................................................................. 2-3 R X3i通用背板尺寸和间距.................................2-5R X3i串行扩展背板尺寸和间距......................2-6 系统配线 ................................................................................................... 2-7 常规配线信息........................................................................ 2-7色标线.................................................................................... 2-7布线安排.............................................................................................. 2-8 系统接地 ............................................................................................. 2-9 接地导体.................................................................................. 2-10背板安全和E M C参考接地...................................2-10电源接地 ......................................................................... 2-11编程器接地 ........................................................................... 2-11屏蔽接地 ..................................................................................... 2-11 系统安装 .......................................................................................... 2-12 通用背板 .............................................................................. 2-12扩展背板............................................................................. 2-14将背板安装在一个19-英寸的机架上 ................................................. 2-16模块 ................................................................................................... 2-18CPU ......................................................................................................... 2-34电源 ........................................................................................ 2-35 GFK-2314 iii杭州集益科技有限公司-您身边的GE PLC专家 0571-********目录串行总线传输模块................................................................. 2-39模块安装................................................................................... 2-39扩展电缆安装 .................................................................... 2-39 第三章背板 ...................................................................................................... 3-1背板种类 ............................................................................................... 3-1RX3i 通用背板: IC695CHS012, IC695CHS016 .............................. 3-2通用背板特性 ................................................................... 3-3通用背板T B1输入端子..................................................3-4Slot 0 ......................................................................................................... 3-4Slot 1到Slot 11 或者15 ................................................................................ 3-5扩展插槽 (Slot 12 或者 16).................................................................... 3-5通用背板上的模块位置...............................................3-6 串行扩展背板: IC694CHS392, IC694CHS398 ........................... 3-7 第四章电源................................................................................................ 4-1电源总览..................................................................................... 4-224 VDC 隔离电源.............................................................................. 4-3RX3i IC695 电源输出 ............................................................ 4-3扩展电源输出 ..............................................................4-4 模块负载要求............................................................................... 4-5电源负载示例 ................................................................ 4-7 用于中性点不接地系统的交流电源连接......................4-8电源, 120/240 VAC 或 125 VDC, 40 Watt: IC695PSA040.................... 4-9指标: IC695PSA040 .................................................................. 4-11发热额定值降级 ................................................................................... 4-12过电流保护 ............................................................................. 4-13现场接线: IC695PSA040 ..................................................................... 4-13 电源, 24 VDC, 40 Watt: IC695PSD040 ............................................. 4-14指标: IC695PSD040 .................................................................. 4-16发热额定值降级 ................................................................................... 4-17过电流保护............................................................................. 4-18现场接线: IC695PSD040 ..................................................................... 4-18 电源, 120/240 VAC或者125 VDC: IC694PWR321............................... 4-19指标: IC694PWR321 ................................................................. 4-20过电流保护............................................................................. 4-20现场接线: IC694PWR321 .................................................................... 4-21 电源, 120/240 VAC 或者 125 VDC 高容量: IC694PWR330........ 4-22指标: IC694PWR330 ................................................................. 4-23过电流保护............................................................................. 4-23现场接线: IC694PWR330 .................................................................... 4-24 电源, 24 VDC高容量: I C694PW R331 ................................... 4-25 iv PACSystems RX3i 系统手册– June 2004 GFK-2314杭州集益科技有限公司-您身边的GE PLC专家 0571-********目录指标: IC694PWR331 ................................................................. 4-26过热额定值降级 ..................................................................................... 4-26过电流保护 ............................................................................. 4-27计算输入功率要求:P W R331 .................................... 4-27现场接线: IC694PWR331 .................................................................... 4-28 第五章串行总线传输模块和扩展电缆....................................5-1串行总线传输模块: IC695LRE001................................................... 5-2 技术指标: LRE001 .............................................................................. 5-3扩展模块安装.................................................................... 5-4关闭独立的扩展背板或者远程背板的电源....................5-4 I/O 总线扩展电缆: IC693CBL300, 301, 302 ,312, 313, 314.................. 5-5 带两个接口的电缆: IC693CBL302 ............................................... 5-5带三个接口的电缆: IC693CBL300, 301, 312, 313, 314 ........... 5-6指标: IC693CBL300, 301, 302, 312, 313, 314 ............................. 5-7自制电缆 .......................................................................................... 5-8扩展或远程背板的端接要求....................5-10 第六章离散输入模块................................................................................... 6-1输入模块, 120 Volt AC, 8 点隔离: IC694MDL230 .............................. 6-2 指标: MDL230 ............................................................................. 6-2现场接线: MDL230 ............................................................................... 6-3 输入模块, 240 Volt AC, 8 点隔离: IC694MDL231 .............................. 6-4 指标: MDL231 ............................................................................. 6-4现场接线: MDL231 ................................................................................ 6-5 输入模块, 120 Volt AC, 16 点: IC694MDL240 ......................................... 6-6 指标: MDL240 ............................................................................. 6-7现场接线: MDL240 ................................................................................ 6-8 输入模块, 24 VAC/ VDC 16 点正/负逻辑: IC694MDL241................. 6-9 指标: MDL241 ............................................................................. 6-9现场接线: MDL241 .............................................................................. 6-10 输入模块, 125 Volt DC正/负, 8 点: IC694MDL632........................... 6-11 指标: MDL632 ........................................................................... 6-12现场接线: MDL632 .............................................................................. 6-13 输入模块, 24 Volt DC正/负, 8 点: IC694MDL634............................. 6-14 指标: MDL634 ........................................................................... 6-14现场接线: MDL634 .............................................................................. 6-15 输入模块, 24 Volt DC正/负, 16 点: IC694MDL645........................... 6-16 指标: MDL645 ........................................................................... 6-16现场接线: MDL645 .............................................................................. 6-17 输入模块: 24 Volt DC 16 点正/负逻辑: IC694MDL646 .................. 6-18 指标: MDL646 ........................................................................... 6-18GFK-2314 目录v杭州集益科技有限公司-您身边的GE PLC专家 0571-********目录现场接线: MDL646 .............................................................................. 6-19 输入模块, 5/12 VDC (TTL) 32 点正/负逻辑: IC694MDL654 .......... 6-20指标: MDL654 ........................................................................... 6-21现场接线: MDL654 .............................................................................. 6-22 输入模块, 24 VDC 正/负逻辑, 32 点: IC694MDL655 ...................... 6-23指标: MDL655 ........................................................................... 6-24现场接线: MDL655 .............................................................................. 6-25 输入模拟器, 8/16 点: IC694ACC300 ...................................................... 6-26指标: ACC300 ........................................................................... 6-26 第七章离散输出模块 ................................................................................ 7-1输出模块, 120 Volt AC, 0.5 Amp, 12 点: IC694MDL310 ....................... 7-2指标: MDL310 ............................................................................. 7-3现场接线: MDL310 ................................................................................ 7-4 输出模块, 120/240 Volt AC, 2 Amp, 8 点: IC694MDL330...................... 7-5指标: MDL330 ............................................................................. 7-6现场接线: MDL330 ................................................................................ 7-7 输出模块, 120 Volt AC, 0.5 Amp, 16 点: IC694MDL340 ....................... 7-8指标: MDL340 ............................................................................. 7-8现场接线: MDL340 ................................................................................ 7-9 输出模块, 120/240 Volt AC 隔离, 2 Amp, 5 点: IC694MDL390 ........... 7-10指标: MDL390 ........................................................................... 7-11现场接线: MDL390 .............................................................................. 7-12 输出模块, 12/24 Volt DC 正逻辑 0.5A 8 点, IC694MDL732 .......... 7-13指标: MDL732 ........................................................................... 7-13现场接线: MDL732 .............................................................................. 7-14 输出模块 125VDC 正/负, 1 Amp, 隔离 6 点: IC694MDL734.......... 7-15指标: MDL734 ........................................................................... 7-15现场接线: MDL734 .............................................................................. 7-16 输出模块, 12/24VDC 正逻辑, 0.5 Amp, 16 点: IC694MDL740 ........... 7-17指标: MDL740 ........................................................................... 7-17现场接线: MDL740 .............................................................................. 7-18 输出模块, 12/24VDC 负逻辑 0.5 Amp, 16 点: IC694MDL741 ............ 7-19指标: MDL741 ........................................................................... 7-19现场接线: MDL741 .............................................................................. 7-20 输出模块, 12/24VDC正逻辑 ESCP, 1A, 16 点: IC694MDL742 .... 7-21电子短路保护............................................................7-21指标: MDL742 ........................................................................... 7-22现场接线: MDL742 .............................................................................. 7-23 输出模块, 5/24 VDC (TTL) 负逻辑, 32 点: IC694MDL752 .......... 7-24指标: MDL752 ........................................................................... 7-25 vi PACSystems RX3i 系统手册– June 2004 GFK-2314杭州集益科技有限公司-您身边的GE PLC专家 0571-********目录现场接线: MDL752 .............................................................................. 7-26典型连接: MDL752 ................................................................. 7-27 输出模块, 12/24VDC, 0.5A 正逻辑, 32 点: IC694MDL753 ............ 7-28 指标: MDL753 ........................................................................... 7-29现场接线: MDL753 .............................................................................. 7-30 输出模块,隔离继电器, N.O., 4 Amp, 8 点: IC694MDL930.............. 7-31 指标: MDL930 ........................................................................... 7-32负载电流限制 .......................................................................... 7-33现场接线: MDL930 .............................................................................. 7-34 输出模块,隔离继电器, N.C. 和 Form C型, 8A , 8 点: IC694MDL931 .... 7-35 指标: MDL931 ........................................................................... 7-36现场接线: MDL931 .............................................................................. 7-37MDL931的负载电流限制....................................................... 7-38 输出模块, 继电器输出, N.O., 2 Amp, 16 点: IC694MDL940 ............. 7-39 指标: MDL940 ........................................................................... 7-40负载电流限制: MDL940........................................................... 7-41现场接线: MDL940 .............................................................................. 7-42 第八章离散混合模块 .................................................................................... 8-1高速计数器模块: IC694APU300 ..................................................... 8-2 指标: APU300.............................................................................. 8-3现场接线: APU300................................................................................. 8-4 第九章模拟量输入模块 ..................................................................................... 9-1模拟量输入处理...................................................................................... 9-2 差分输入 ....................................................................................... 9-2 模拟量输入模块,4通道差分电压:I C694A L G220................. 9-3 指标: ALG220.............................................................................. 9-4数据格式: ALG220 ................................................................................ 9-5现场接线: ALG220 ................................................................................. 9-6 模拟量输入模块,4通道差分电流:I C694A L G221 ................. 9-7 LEDs.......................................................................................................... 9-7指标: ALG221.............................................................................. 9-8数据格式: ALG221 ................................................................................ 9-9现场接线: ALG221 ............................................................................... 9-10 模拟量输入模块, 16 / 8 通道电压: IC694ALG222.......................... 9-11 LEDs........................................................................................................ 9-11指标: ALG222........................................................................... 9-12配置: ALG222 ............................................................................ 9-13数据格式: ALG222 .............................................................................. 9-14现场接线: ALG222 ............................................................................... 9-16 模拟量输入模块, 16 通道电流: IC694ALG223.............................. 9-17GFK-2314 目录vii杭州集益科技有限公司-您身边的GE PLC专家 0571-********目录模块电源 .......................................................................................... 9-17LEDs........................................................................................................ 9-17指标: ALG223............................................................................ 9-18配置: ALG223 ............................................................................ 9-19数据格式: ALG223 .............................................................................. 9-20现场接线: ALG223 ............................................................................... 9-22 第十章模拟量输出模块 ................................................................................ 10-1模拟量输出模块, 2 通道电压: IC694ALG390............................... 10-2LED.......................................................................................................... 10-2指标: ALG390............................................................................ 10-3数据格式: ALG390 .............................................................................. 10-4现场接线: ALG390 ............................................................................... 10-5 模拟量输出模块, 电流, 2 通道: IC694ALG391 ............................. 10-6LED.......................................................................................................... 10-6指标: ALG391............................................................................ 10-7负载电流降级 ............................................................................. 10-7数据格式: ALG391 .............................................................................. 10-8现场接线: ALG391 ............................................................................... 10-9 模拟量输出模块,电流/电压, 8 通道:I C694ALG392 .............. 10-11LEDs...................................................................................................... 10-11指标: ALG392.......................................................................... 10-12额定降低曲线: ALG392 ...................................................................... 10-13电流和电压范围和分辨率 .........................................10-15模块数据 .......................................................................................... 10-16现场接线: ALG392 ............................................................................. 10-17配置: ALG392 .......................................................................... 10-18 第十一章模拟量混合模块 .................................................................................... 11-1模拟量模块, 4 输入/2 输出, 电流/电压型: IC694ALG442............... 11-2模块特性 ...................................................................................... 11-2隔离的 +24 VDC 电源.......................................................................... 11-2LEDs........................................................................................................ 11-2指标: ALG442............................................................................ 11-3现场接线: ALG442 ............................................................................... 11-5输入缩放比例 ............................................................................................ 11-6I/O 数据: ALG442 .................................................................................... 11-8状态数据: ALG222 ............................................................................... 11-9配置: ALG442 .......................................................................... 11-10ALG442的斜坡模式处理....................................................... 11-11根据需求转换模块处理............................................11-13 viii PACSystems RX3i 系统手册 – June 2004 GFK-2314杭州集益科技有限公司-您身边的GE PLC专家 0571-********目录第十二章特殊模块 ............................................................................. 12-1以太网接口模块: IC695ETM001 ....................................................... 12-2 指标: IC695ETM001 .................................................................. 12-3以太网接口 ........................................................................... 12-3站管理器 ...................................................................................... 12-4固件升级 ................................................................................. 12-4以太网全局数据 (EGD) .................................................................... 12-4 以太网接口的控制和指示器....................................................... 12-5 LEDs........................................................................................................ 12-5以太网重启动按钮 .................................................................... 12-5连接器 .............................................................................................. 12-5 运动控制模块: IC694DSM314 ............................................................... 12-6 总览.................................................................................................. 12-7特性: DSM314 ................................................................................... 12-8屏蔽接地连接 ....................................................................... 12-8 附录 A 产品认证和遵循的安装指导.........A-1 RX3i 机构认证 .....................................................................................A-1UL Class 1 Division 2 危险区域必须条件 .................................A-2AT EX Cl a s s 1 Z o n e 2危险区域必须条件.................................A-2标准总揽..........................................................................................A-3 P A C S y s t e m s R X3i环境指标.......................................A-3附加的 RX3i 技术指标....................................................................A-3技术指标 Group 1 ...............................................................................A-4技术指标 Group 2 ...............................................................................A-5 政府规定...................................................................................A-6和标准一致的安装向导.......................................A-7 安装金属外壳的要求.....................................A-8 屏蔽电缆替代金属管道选择...............................................................A-9 通信电缆 ..............................................................................A-9I/O 电缆..................................................................................................A-9模拟/高速计数器电缆 ........................................................................A-9控制柜供电(I C694电源)..............................A-10屏蔽终端 ...................................................................................A-11专业的屏蔽电缆供货商 ...........................................................A-11 欧洲地区有关安全的安装指导....................A-12GFK-2314 目录ix杭州集益科技有限公司-您身边的GE PLC专家 0571-******** Contents附录 B 32-点模块的I/O电缆 .................................................................... B-1预制I/O电缆:I C693C B L327/328和IC693CBL329/330/331/332/333/334..................................................................B-2连接器深度........................................................................................B-3 32-点模块的接线端子块: IC693ACC337.........................................B-4自制长度的 24–针连接器电缆制作 ............................................B-5自制电缆的连接器深度..................................................B-6 附录 C 散热计算 .........................................................................C-1模块散热 ........................................................................... C-1电源散热 .................................................................C-1离散输出模块散热...........................................C-2离散输入模块散热..............................................C-3总散热 ............................................................................... C-4 附录 D 电缆屏蔽层箝位组件................................................................. D-1安装电缆夹子组件...............................................................D-2电缆直径 ......................................................................................... D-2剥去绝缘外壳 ................................................................. D-3典型安装.................................................................................... D-3 x PACSystems RX3i 系统手册– June 2004 GFK-2314产品介绍本章节将对 PACSystems™ RX3i 产品和其特性进行概括性的介绍。

GE智能平台PACSystemsRX3i系统在油库站控系统中的应用摘要:本文通过对大庆南三油库站控系统的介绍，向读者描述了GEIP智能平台PAC3i系统在油库站控系统中成功应用的一套完整解决方案。

关键字：GE智能平台 PACSystems RX3i 站控系统油库应用背景：位于黑龙江省大庆市林源的南三油库隶属于中国石油天然气集团公司，是大庆油田的原油储备库和中转枢纽。

同时，南三油库也是我国从陆路进口俄罗斯原油的重要战略储备库，2004年至今南三油库已累计接卸俄油3000余万吨。

坐落在南三油库的生产运行库是为提高油库原油集中输送与储运能力而修建的大型储运工程，主要发挥将南一油库和北油库的原油集中存储并择机向下游林源泵站外输，并最终外运的功能。

解决方案南三油库的主要作用是完成大庆油田原油和俄罗斯进口原油的收、发、输转和储存任务。

油库的站控系统则是使整个油库储运系统的各个环节有机结合起来，并保证各个环节正常运转，以达到及时、保质、保量、安全地完成原油的收、发、输转和储存任务。

为此，南三油库站控系统需要一套可靠性高、易于操作、维护方便、性价比高的一套自动化控制系统。

北京中佳荣盛科技有限公司结合多年以来石油化工领域应用经验，并结合GE智能平台的先进控制器产品，给出了一套适合于用户需求的自动化控制系统方案。

根据南三油库工艺流程和结构，油库站控系统主要由三个流程部分组成。

这三个流程具体是储运流程、冷凝水流程、给排水流程。

这三个流程由一套GE智能平台的PACSystems RX3i 高性能、先进控制系统来实现控制。

解决方案可大致分为以下三个部分。

• 高速以太通讯网络。

• PACSystems RX3i 高性能、先进控制控制器及其本地I/O系统。

• 上位机操作员站和工程师维护工作站。

系统结构图可以参见图1所示。

图1 系统结构图1、高速以太通讯网络以太网通讯快速地发展与广泛地普及，其无可比拟的高速与互联互通的优势，使以太网通讯成为目前世界上工业控制领域高速通讯的事实标准与未来通讯的发展趋势。

Rx3i PacSystem919-535-3180*******************GE Fanuc IC695NIU001/automation/ge-fanuc/rx3i-pacsystem/IC695NIU001RX3i NIU with two serial ports and 20K of local logic. IC695N IC695NIIC695NIUPACSystems* RX3iIC695NIU001 PLUSGFK-2598 Ethernet Network Interface UnitMarch 2011The PACSystems * RX3i Ethernet NIU PLUS,IC695NIU001, makes it possible to use PACSystems RX3i and Series 90-30 I/O remotely on an Ethernet network. Once set up by configuration, data exchange is completely automatic. System control can be provided by any master device capable of exchanging Ethernet Global Data (EGD). The Ethernet NIU automatically provides the controller with status information in each exchange. The application program logic in the controller can monitor this status data, and issue appropriate commands to the Ethernet NIU.▪ ▪ ▪ ▪ ▪ ▪ ▪see the Manual, GFK-2314.▪ ▪ storage.▪ ▪ ▪ RS-232 serial port.▪ based Ethernet Interface module (IC695ETM001) ▪ Data exchange using EGD▪ TCP/IP communication services using SRTP ▪Comprehensive station management/diagnostic tools*indicates a trademark of GE Intelligent Platforms, Inc. and/or its affiliates. All other trademarks are the property of their respective owners.▪ Supports operation with redundant controllers▪ PACSystems RX7i and RX3i controllers can sendselected COMMREQs to the RX3i ENIU via EGD. The ENIU executes the COMMREQs and returns the results to the controller.▪ During EGD configuration, RX3i Ethernet interfaces are identified by their Backplane/Slot locations.▪Supports display of module hardware revision, serial number and date code in Machine Edition Logic Developer software.GFK-2598Ethernet Global Data FeaturesThe Ethernet NIU communicates with its controller via EGD exchanges. One exchange is used to send outputs to the ENIU and another exchange is used to send inputs back to the controller. The ENIU supports receiving outputs from redundant controllers. By sending the EGD exchange to a group address both controllers can receive the inputs. Up to 1300 bytes of outputs can be sent to a set of ENIUs from a controller. Each ENIU can send up to 1300 bytes of inputs to the controller.A typical system might consist of a controller with five ENIUs. The controller sends 1300 bytes of outputs and each ENIU sends 100 bytes of inputs to the controller. This typical system would have its I/O updates occur in less than 25 milliseconds. If the controller scan time is greater than 25 milliseconds, the update occurs at the controller’s scan rate. This performance timing is a guideline, not a guarantee, and assumes that there is no other traffic on the Ethernet link to the I/O. Performance data for other system configurations can be found in the Ethernet NIU User’s Manual, GFK-2439. Ethernet NIU COMMREQ SupportThe Ethernet NIU supports COMMREQs that are sent to it by a C block application in a PACSystems RX7i or RX3i controller. This feature is not available with other types of controllers. Ladder code in the RX7i or RX3i CPU interfaces to the C block. The C block sends COMMREQ commands to the Ethernet NIU in an Ethernet Global Data Exchange. The Ethernet NIU executes the COMMREQ and sends the results back to the RX7i or RX3i using another EGD exchange. The following COMMREQs can be sent in this way:▪Modbus Master – function codes 1, 2, 3, 4, 5, 6, 7, 15, 16, 17▪Genius – enable/disable outputs, switch BSM, clear fault, clear all faults, assign monitor, read diagnostic▪PROFIBUS Master – COMMREQs 1, 2, 4, 5, 6▪Motion (DSM314/DSM324) – load parameters▪High Speed Counter – Data command▪DeviceNet Master – COMMREQs 1, 4, 5, 6, 7, 9▪Analog Module – HART Protocol COMMREQs.In addition, any COMMREQ supported by a module in the Ethernet NIU can be sent as a Generic COMMREQ, with the exception of DeviceNet Master Send Extended Explicit Message. For more information, see the PACSystems RX3i Ethernet NIU User’s Manual, GFK-2439.For environmental specifications and compliance to standards (for example, FCC or European Union Directives), refer to the PACSystems RX3i Hardware and Installation Manual, GFK-2314.GFK-2598Note: For Conformal Coat option, please consult the factory for price and availability.NIU Plus Battery and Switch LocationsFront View Rear ViewGFK-2598 SwitchesThe Ethernet NIU Plus has two switches. The Reset switch is not used. The three-position Run/Stop switch is located behind the protective door, as shown above.Unlike the Run/Stop switch on a CPU module, on an Ethernet NIU the use of this switch is disabled by default. If the switch is to be used to control the Run or Stop mode operation of the NIU, clear faults, and/or prevent writing to program memory or configuration, it must be enabled on the Settings Tab of the Ethernet NIU configuration in the folder, and stored to the ENIU.Stop, I/O DisabledStop, I/O EnabledReal Time Clock BatteryThe NIU Plus is shipped with a real time clock (RTC) battery (IC690ACC001) installed, with a pull-tab on the battery. The pull-tab should be removed before installing the module.The RTC battery has an estimated life 5 years. Battery must be replaced every 5 years on a regular maintenance schedule.GFK-2598Important Product Information for this ReleaseThe NIU001 Plus is a drop-in replacement for the NIU001 Classic module, with no changes to configuration, logic or wiring required. For new features and problems resolved, see page 6.UpgradesNIU001 Plus firmware upgrades are not compatible with NIU001 Classic hardware.GFK-2598NIU001+ Problems Resolved by Release 6.80SVC_REQ 57: Logic Driven Write to Nonvolatile Storage: In previous versions of the firmware, writing a partial block of word memory would result in incorrect data being written.For example:∙%R1 to %R10 are written to flash using SVC_REQ 57∙The values of %R3, %R4, %R6 changes∙%R1 to %R10 are again written to flash using SVC_REQ 57. The actual values written to flash will be incorrect.If all of the values, %R1 through %R10 have changed, the correct values would be written to flash.This issue has been fixed in firmware version 6.80New Features in Release 6.80∙This release enables support that is functionally identical to the IC695NIU001 on the new IC695NIU001+.∙The hardware revision, serial number and date code of the Ethernet NIU IC695NIU001+ can be displayed after upgrading to Proficy Machine Edition version 6.5 or later. To access this information, select Online Commands, Show Status and then click the Details button.GFK-2598GFK-2598GFK-2598GFK-2598GFK-2598GFK-2598User Manual UpdatesThe following information will be included in the next scheduled revision of the PACSystems CPU Reference Manual,GFK-2222.SVC_REQ 57: Logic Driven Write to Nonvolatile StorageThe following paragraphs will be added to the discussion of SVC_REQ 57 on page 9-59 of the CPU Reference Manual.This feature uses 65,536 bytes of nonvolatile storage. But not all of this memory is available for the actual data being written by the service request. Some of the memory is used internally by the PLC to maintain information about the data being stored.You can generally make the most efficient use of nonvolatile storage by transferring data in 56-byte increments, since this will actually write 64 bytes to the device. Given the bookkeeping overhead required by the PLC and possiblefragmentation, at least 54,912 bytes and no more than 64,000 bytes will be available for the reference data and the 8 bytes of command data for each invocation. For additional information on fragmentation see page 9-12.FragmentationDue to the nature of the media in PACSystems CPUs, writes may produce fragmentation of the memory. That is, small portions of the memory may become unavailable, depending upon the sequence of the writes and the size of each one.Data is stored on the device in 128 512-byte sections. Each section uses 12 bytes of bookkeeping information, leaving a maximum of 64,000 bytes devoted to the reference data and command data for each invocation. However, the data for a single invocation cannot be split across sections. So, if there is insufficient space in the currently used section to contain the new data, the unused portion of that section becomes lost. For example, suppose that the current operation is writing64 bytes of reference data and 8 bytes of command data (72 bytes total). If there are only 71 bytes remaining in the currentsection, the new data will be written to a new section and the unused 71 bytes in the old section become unavailable.RX3i I/O Module Sweep Impact TimesThe following table will be added to the RX3i sweep impact data on page A-22 of the CPU Reference Manual.DSM314 Scan Time Contribution in milliseconds.UL Class 1 Division 2 & ATEX Zone 2 Hazardous Area Warnings1. EQUIPMENT LABELED WITH REFERENCE TO CLASS I, GROUPS A, B, C, D, DIV. 2 HAZARDOUS AREAS ISSUITABLE FOR USE IN CLASS I, DIVISION 2, GROUPS A, B, C, D OR NON–HAZARDOUS LOCATIONS ONLY.2. WARNING – EXPLOSION HAZARD – SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FORCLASS I, DIVISION 2 & ATEX ZONE 2.3. WARNING – EXPLOSION HAZARD – DO NOT DISCONNECT EQUIPMENT UNLESS POWER HAS BEENSWITCHED OFF OR THE AREA IS KNOWN TO BE NON–HAZARDOUS.ATEX Zone 2 Hazardous Area RequirementsIn order to maintain compliance with the ATEX Directive, a RX3i system located in a Zone 2 area (Category 3) must be installed within a protective enclosure meeting the criteria detailed below:∙IP54 or greater, and∙Mechanical strength to withstand an impact energy of 3.5 Joules。

Rx3i PacSystem919-535-3180*******************GE Fanuc IC694APU300/automation/ge-fanuc/rx3i-pacsystem/IC694APU300High speed counter module 200KHZ A B and C type. IC694A IC694APIC694APU8-2 PACSystems* RX3i – August 2011 GFK-2314DHigh-speed Counter Module: IC694APU300The High-speed Counter module, IC694APU300, provides direct processing of rapid pulse signals up to 80 kHz. The module senses inputs, processes the input count information, and controls the outputs without needing to communicate with a CPU.The High Speed Counter uses 16 bits of discrete input memory (%I), 15 words of analog input memory (%AI), and 16 bits of discrete outputmemory (%Q) in the CPU. The High-speed Counter can be configured to have:▪ 4 identical, independent simple counters ▪ 2 identical, independent more complex counters ▪ 1 complex counterTwo green LEDs indicate the operating status of the module and the status of configuration parameters. Additional module features include:▪ 12 positive logic (source) inputs with input voltage range selection of either 5 VDC or 10 to 30 VDC ▪ 4 positive logic (source) outputs▪ Counts per timebase register for each counter ▪ Internal module diagnostics▪A removable terminal board for field wiringInputs can be used as count signals, direction, disable, edge-sensitive strobe, and preload inputs depending on the counter type selected by the user. Outputs can be used to drive indicating lights, solenoids, relays, and other devices. Power for the module is drawn from the backplane’s 5VDC bus. Power sources for input and output devices must be supplied by the user or by the +24 VDC Isolated output of the power supply. The module also provides a selectable threshold voltage to allow the inputs to respond to either 5VDC signal levels or 10 to 30VDC signal levels.The blue bands on the label show that APU300 is a low-voltage module. This module can be installed in any I/O slot in an RX3i system.Refer to Appendix A for product standards and general specifications.Input ImpedanceGFK-2314D Chapter 8 Discrete Mixed Modules 8-3Field Wiring: APU300Wiring information for APU300 is shown below.Shielded cable must be used for connecting to the High Speed Counter module. The shield for the cable must have a high frequency ground within 6 inches (15.24 cm) of the module to meet the IEC 1000-4-4 levels specified in Appendix A. The cable’s length is limited to 30 meters.Terminals Field WiringAll 12 High Speed Counter inputs are single-ended positive logic (source) type inputs. Transducers with CMOS buffer outputs (74HC04 equivalent) can directly drive the High-speed Counter inputs using the 5V input range. Transducers using TTL totem pole or open-collector outputs must include a 470 ohm pull-up resistor (to 5V) to guarantee compatibility with the High-speed Counter inputs. Transducers using high voltage open collector (sink) type outputs must have a 1K pull-up resistor to + 12V for compatibility with the High-speed Counter 10 to 30 volt input range.The 5VDC threshold is selected by connecting a jumper between two terminals on the detachable terminal board connector. Leaving the threshold selection terminals unconnected places the inputs in the default 10 to 30 VDC voltage range.Do not connect 10 to 30 VDC to the module inputs when the 5 VDC inputrange (pins 13 to 15 jumpered) is selected. Doing so will damage themodule.8-4 PACSystems* RX3i – August 2011 GFK-2314DTerminal Assignments for Each Counter TypeThe following table shows which terminals to use for the type of counter selected during module configuration.(1). Type B counter:A1, B1 are the A and B inputs for counter 1.A2, B2 are the A and B inputs for counter 2.(2) Type C Counter:A1, B1 are the A and B count inputs for (+) loopA2, B2 are the A and B count inputs for (–) loop(3) OUTPWR does not source power for user loads. Output power must be supplied from an external supply.* Inputs and outputs identified by two numbers separated by a decimal point indicate the counter number to the left of the decimal point and the element number on the right. For example, STRB1.2 indicates Counter 1, Strobe 2 input.GFK-2314D Chapter 8 Discrete Mixed Modules 8-5。

Rx3i PacSystem919-535-3180*******************GE Fanuc IC695HSC304/automation/ge-fanuc/rx3i-pacsystem/IC695HSC304RX3i High Speed Counter, 4 channels. 8 configurable inputs and 7 con-figurable IC695H IC695HS IC695HSCPACSystems* RX3iIC695HSC304 and IC695HSC308 GFK-2458C High-Speed Counter ModulesMarch 2012provide direct processing of rapid pulse signals up to 1.5MHz for industrial control applications such as:▪Turbine flowmeter▪Meter proving▪Velocity measurement▪Material handling▪Motion control▪Process controlThese modules can sense inputs, process input countinformation, and control outputs without CPUintervention.High-speed Counter module IC695HSC304 provides: 8high-speed inputs, 7 high-speed outputs, and 1 to 4counters.High-speed Counter module IC695HSC308 provides: 16high-speed inputs, 14 high-speed outputs, and 1 to 8counters.Standard counter types A, B, C, D, E , Z, and a user-defined type can be combined on a module.Module features include:▪Hot insertion/extraction▪Terminal Block insertion or removal detection▪Meets CE, UL/CUL 508 and 1604, and ATEXrequirements▪Flash memory for future upgrades▪Module fault reporting▪Configurable I/O InterruptsSelect module parameters easily changed without re-configuration.These modules must be located in an RX3i Universal Backplane.High-Speed Counter modules can be used with a Box-style (IC694TBB032), Extended Box-style (IC694TBB132), Spring-style (IC694TBS032), or Extended Spring-style (IC694TBS132)) Terminal Block. Extended terminal blocks provide the extra shroud depth needed for shielded wiring. See the PACSystems RX3i System Manual,GFK-2314 revision B or later for more information about Terminal Blocks. Terminal Blocks are ordered separately. RX3i High-speed Counter Modules can be hot-inserted and removed following the instructions in the PACSystems RX3i System Manual, GFK-2314. When the module is removed from the backplane or power-cycled, it stops counting and accumulated counts are lost.*indicates a trademark of GE Intelligent Platforms, Inc. and/or its affiliates. All other trademarks are the property of their respective owners. All rights reserved.GFK-2458CSpecifications: IC695HSC304 and IC695HSC308For product standards and general specifications, refer to the PACSystems RX3i System Manual, GFK-2314.For detailed information on High Speed Counter module installation, configuration, operation, and diagnostics, refer to PACSystems RX3i High-speed Counter Modules User’s Manual, GFK-2441.GFK-2458COutput Points versus TemperatureThe charts below show thermal deratings for modules IC695HSC304 and IC695HSC308 with maximum loads of 0.75A on each output.For example, if five outputs are used on module IC695HSC304, at 60C the total current of all outputs would be 3.75 Amps. If smaller loads are used on the outputs, then more output channels can be used at a given temperature.IC695HSC304 with 0.75A Output Loads454647484950515253545556575859601234567Output ChannelsA m b i e n t (D e g r e e s C )For module IC695HSC308, more output channels can be used at the same time at a given ambient temperature when outputs are evenly distributed into two groups. If outputs are either set up as one output group or unevenly distributed between two output groups, fewer output channels can be used for a given ambient temperature. For example, if eight outputs are used on module IC695HSC308, and they are equally distributed between two output groups, the total current of all outputs at 60C can be up to 6 Amps. At a given ambient temperature, if smaller loads are used on the outputs, more output channels can be used.IC695HSC308 with 0.75A Output LoadsOutput Channels354045505560A m b i e n t (D e g r e e s C )Combined Groups, with outputs evenly distributed into two output groupsSingle Group of outputs1234567891011121314GFK-2458CInstallation in Hazardous Areas∙EQUIPMENT LABELED WITH REFERENCE TO CLASS I, GROUPS A, B, C & D, DIV. 2 HAZARDOUS AREAS IS SUITABLE FOR USE IN CLASS I, DIVISION 2, GROUPS A, B, C, D OR NON-HAZARDOUS AREAS ONLY ∙WARNING - EXPLOSION HAZARD - SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR CLASS I, DIVISION 2;∙WARNING - EXPLOSION HAZARD - WHEN IN HAZARDOUS AREAS, TURN OFF POWER BEFORE REPLACING OR WIRING MODULES; AND∙WARNING - EXPLOSION HAZARD - DO NOT CONNECT OR DISCONNECT EQUIPMENT UNLESS POWER HAS BEEN SWITCHED OFF OR THE AREA IS KNOWN TO BE NONHAZARDOUS.Diagnostic and Status DataFor additional information, refer to “Module Data” in the PACSystems RX3i High-speed Counter Modules User’s Manual, GFK-2441. Manuals and other user documentation are available for download on the Support website:/supportCounter Status Data Format for Each CounterFor each Counter, the Counter Status data has the format shown below. Unused bits are set to 0. Status bits for Preloads (and others) are set if a source triggers an event.GFK-2458CI/O Status Data FormatThe I/O Status Data has the format shown below. Reserved bits are always 0.* The Output Status bits are set regardless of the source (Module Control data or Setpoints).Module Status DataThe Module Status data provides the CPU with basic diagnostic information about module operation. For both RX3iHigh-Speed Counter modules the length of this data is 32 bits. During module configuration, it can be assigned to any available references in %I, %M, or %T memory, or to discrete I/O variables.GFK-2458CLEDsIndividual green LEDs indicate the ON/OFF status of the module’s extern al input and output points. These LEDs are green when the corresponding points are on. They are off when the corresponding points are off. LED positions are illustrated below.External Input PointsThe Module Status (S1) LED indicates the status of the module. Solid green indicates that the module has been configured. Blinking green indicates no configuration. Blinking amber/yellow indicates a fatal module failure.The Field Status (S2) LED is off if field power is not present. For module IC695HSC308, this LED is off unless power is present on BOTH V A and V B. Solid green indicates that field power is present and that no output circuit faults have been detected on circuits for which fault detection has been enabled in the configuration. If S2 is amber/yellow, field power is present but circuit faults exist for one or more outputs.The module’s red/green Terminal Block LED is green when the module’s removable terminal block is locked in place. It is red when the terminal block is not locked. The module also sends an Addition of Terminal Block or Loss of Terminal Block message to the RX3i CPU to report the Terminal Block status.During a firmware update, the S1, S2, and TB LEDs blink in a green/off pattern.GFK-2458CField Wiring: IC695HSC304Field wiring connections to the module are made to the removable terminal assembly, as described in the RX3i System Manual, GFK-2314. For this module, each row of terminals (eg: 1-18, 19-36) is internally connected. The dual connection points are for wiring convenience; the module cannot be wired for differential inputs. For installations that must meet radiated emissions requirements as in EN 55022, this module’s high-speed connections must be made with double-shielded cable. The outside braided shield should be terminated at the entrance to the enclosure and not continue within the enclosure. Both ends of the shielded cable should be grounded. If low-frequency (power line) ground loops are an issue with the application, directly ground one end of the shielded cable and capacitively tie the other end of the shielded cable to ground with approximately 0.01µf capacitance.All outputs on module IC695HSC304 form a single output group.Field Wiring Terminals Field WiringGFK-2458CField Wiring: IC965HSC308Field wiring connections to the module are made to the removable terminal assembly, as described in the RX3i System Manual, GFK-2314. All 16 High-Speed Counter inputs on this module are positive logic (source) type. For installations that must meet radiated emissions requirement s as in EN 55022, this module’s high-speed connections must be made with double-shielded cable. The outside braided shield should be terminated at the entrance to the enclosure and not continue within the enclosure. Both ends of the shielded cable should be grounded. If low-frequency (power line) ground loops are an issue with the application, directly ground one end of the shielded cable and capacitively tie the other end of the shielded cable to ground with approximately 0.01µf capacitance.Field Wiring Terminals Field Wiring Inputs 1 to 16 form one isolated inputgroup. Outputs 1 to 7 and 8 to 14form two isolated output groups, eachwith its own voltage connections.Outputs should be evenly distributedbetween the two output groups, asdiscussed under “Output Pointsversus Temperature”.GFK-2458C Release HistoryThese modules must be located in an RX3i Universal Backplane. An RX3i CPU with firmware version 3.81 or later is required. Machine Edition 5.50 with Service Pack 2 SIM 3 or later is required for configuration.Important Product Information for this ReleaseRestrictions and Open Issues in this ReleaseDescription: In applications that include Timed Interrupts or I/O Interrupts, some IC693****** and IC694****** modules in a PACSystems RX3i main or expansion backplane may occasionally be lost during interrupt processing. A fault is logged in the fault table.Recommendations: Minimize the time of individual interrupts and the elapsed time of overlapping interrupt blocks. Cycle power to a lost module to restore operation. If the module supports hot-swapping, that will also restore operation.。

PACSystems RX3i 控制器第一章 PACSystems RX3i 控制器全新的控制器 RX3i 是 PACSystems 可编程自动化控制器 （PAC ） 家族的最新成员。

同 PACSystems 家族的其他成员一样，PACSystems RX3i 拥有一个单一的控制引擎和一个通用的编程环境，它能方便地应用在多种硬件平台上，并且提供真正的集中控制选择。

GFK-2222GFK-2224GFK-2225GFK-2259GFK-2314参考出版物表 ：PACSystems CPU 参考手册PACSystems TCP/IP 以太网通讯手册PACSystems 站管理 用户手册PACSystems C 语言编程工具包用户手册PACSystems RX3i 硬件与安装手册背板 第3页电源模块 第4页-第5页扩展模块 第32页模拟量I/O 模块（输入） 第9页-第15页模拟量I/O 模块（输出） 第21页-第22页CPU 第2页离散量I/O 模块（输出） 第16页-第20页离散量I/O 模块（输入） 第6页-第8页分布式I/O 通讯模块 第28页特殊/运动控制模块 第29页-第31页RX3i 特性Proficy TM Machine Edition拥有300M H z I n t e l 微处理器和10Mbytes 用户内存的高性能控制器。

无需多个控制器，使您的控制更加简单。

广泛的 I/O 模块选择（已推出40多种）适合从简单到复杂的应用；此外，系统还提供多种网络接口模块。

PACSystems 便携控制引擎在不同的平台上都能提供出色的性能，使 OEM 和最终用户都能从众多的应用选择方案中找到最适合他们需要的控制系统硬件 —— 所有需要都在一个单一、紧凑而且高度集成的组件中。

通用的PCI 总线背板，背板高速PCI 总线速度为 27MHz ，使得复杂 I/O 的数据吞吐率更大，简单 I/O 的串行总线读写更快，优化了系统的性能和投资。

4-36 PACSystems™ RX3i System Manual – October 2005 GFK-2314CPower Supply, 120/240 VAC or 125 VDC High Capacity: IC694PWR330outputs:▪ ▪ ▪LEDsor power is not applied.The green OK LED is steady ON if the PLC isoperating properly. It is OFF if a problem is detected by the PLC.The green RUN LED is ON when the PLC is in Run mode.GFK-2314C Chapter 4 Power Supplies 4-37Specifications: IC694PWR330Nominal Rated VoltageInput Voltage Range AC DC120/240 VAC or 125 VDC85 VAC to 264 VAC 100 VDC to 300 VDCInput Power(Maximum with Full Load) 100 VA with VAC Input 50 W with VDC InputInrush Current 4 Amperes peak, 250ms maximumOutput Power5 VDC: 30 Watts maximum24 VDC Relay: 15 Watts maximum 24 VDC Isolated: 20 Watts maximumNOTE: 30 Watts maximum total (all three outputs) Output Voltage5 VDC: 5.0 VDC to 5.2 VDC (5.1 VDC nominal) 24 VDC Relay: 24 VDC to 28 VDC24 VDC Isolated: 21.5 VDC to 28 VDC Isolation (input to backplane):1500 VAC (for 1 minute)Protective Limits Overvoltage: Overcurrent:5 VDC output: 6.4 VDC to 7 VDC 5 VDC output: 7 Amperes maximumRide-through Time:20 ms minimum. This is the length of time the Power Supply maintains valid outputs if the power source is interrupted.Fuse2 Amps, GE Fanuc part number 44A724627-109 (2). See chapter 2 for more information.Overcurrent ProtectionThe 5 VDC output is electronically limited to 7 Amps. If an overload (including short circuits) occurs, it is sensed internally and the Power Supply shuts down. The Power Supply continually tries to restart until the overload condition is removed. An internal fuse in the input line isprovided as a backup. The Power Supply usually shuts down before the fuse blows. The fuse also protects against internal supply faults.WarningThe power supply’s door must be closed. During normal operation with an AC power source either 120 VAC or 240 VAC is present on the AC Power Supply. The door protects against accidental shock hazard that could cause severe or fatal injury to personnel.4-38 PACSystems™ RX3i System Manual – October 2005 GFK-2314CField Wiring: IC694PWR330AC Power Source ConnectionsThe Hot, Neutral, and Ground wires from the 120 VAC power source or L1, L2, and Ground wires from the 240 VAC power source connect to the top three terminals on the Power Supply.DC Power Source ConnectionsConnect the + and - wires from the 125 VDC power source to the top two terminals. These connections are not polarity-sensitive on Power Supply PWR330.WarningIf the same external DC power source is used to provide power to two or more power supplies in the system, connection polarity must be identical at each power supply. A resulting difference in potential can injure personnel or cause damage to equipment. Also, each backplane must be connected to a common system ground.The bottom two terminals of the power supply terminal strip provide output connections to the Isolated +24 VDC. This output can be used to provide power for external circuits (within power limitations of the supply).CautionIf the Isolated 24 VDC supply is overloaded or shorted, the PLC will stop operation.Input Overvoltage ProtectionTerminal 4 is normally connected to frame ground (terminal 3) with a factory-installed jumper strap. If overvoltage protection is not required or is supplied upstream, this feature can be disabled by removing the jumper. To Hi-pot test this supply, overvoltageprotection must be disabled during the test by removing the terminal strip jumper. Re-enable overvoltage protection after testing by reinstalling the strap.In systems with a floating neutral input (the neutral line is not referenced to Protective Earth Ground), this jumper must NOT be installed. In a floating neutral system, voltage surge protection devices such as MOVs must be installed from L1 to earth ground, and from L2 (Neutral) to earth ground.。

Rx3i PacSystem919-535-3180*******************GE Fanuc IC694MDL350/automation/ge-fanuc/rx3i-pacsystem/IC694MDL350120/240 Vac Isolated Output, 2 Amp (16 Points). IC694M IC694MDIC694MDL7-10 PACSystems™ RX3i System Manual – October 2005 GFK-2314COutput Module, 120VAC 16 Point Isolated, IC694MDL350The 120/240VAC 16-Point Isolated Output module, IC694MDL350, provides 16 individually-isolated output points. A high level of noise immunity minimizes the need for external snubbers to protect theoutputs against transient electrical noise on the power line. The outputs can control a wide range of inductive and incandescent loads. Power to operate the output loads must be provided with an external AC power supply.A DIP switch on back of the module is used to select the outputs’ default mode: Force Off or Hold Last State. The module must be removed from the backplane to set this switch.This module can be used with a Box-style (IC694TBB032), Extended Box-style (IC694TBB132), Spring-style (IC694TBS032), or Extended Spring-style (IC694TBS132) Terminal Block. Extended terminal blocks provide the extra shroud depth typically needed for field wiring to AC devices. See chapter 15 for more information on Terminal Blocks. Terminal Blocks are ordered separately.Individually-numbered LEDs show the ON/OFF status of each output point. The TB LED indicates presence of the removable Terminal Block. The TB LED is green when the Terminal Block is present or red when the Terminal Block is not present. The red bands on the door card indicate the MDL350 is a high-voltage module.The IC694MDL350 module can be installed in any I/O slot in an RX3i system. It must be used with an RX3i CPU release 3.50 or greater. It cannot be used with a Series 90-30 PLC CPU.GFK-2314C Chapter 7 Discrete Output Modules 7-11Specifications: IC694MDL350Rated Voltage 120/240 volts ACOutput Voltage Range74 – 265VAC (47 to 63 Hz), 120/240VAC nominal Outputs per Module 16 isolated Isolation:Field to Logic Side 250 VAC continuous; 1500 VAC for 1 minute Group to Group250 VAC continuous; 1500 VAC for 1 minutePower Consumption 315 mA (with all outputs ON) from 5 volt bus on backplane Diagnostics Field side terminal block status reported to RX3i CPU Output Current (Linear derating) Per Point 2A max. @ 30°C, 1A max. @ 60°CPer Module 5A max. @ 30°C, 4A max. @ 60°C Output CharacteristicsInrush Current 20 Amps maximum for one cycle Minimum Load Current 10 mA per point Output Voltage Drop 1.5 volts maximum Output Leakage Current 2 mA maximum On, Off Response Times 1/2 cycle maximumFuses No internal fusing. Use of appropriate external fuses is recommended for short circuit protection.Refer to Appendix A for product standards and general specifications.Setting the Output DefaultsThe DIP switch on back of the module selects the default operation for the module’s outputs. The module must be removed from the backplane to set this switch. Note that there are two DIP switches on the module. Only the upper switch is used for this module.With the Outputs Default Mode switch in the right (open) position, the outputs will turn off whenever communication with the CPU is lost. When the switch is in the left position, the outputs will hold their last programmed value whenever communication with the CPU is lost.Backplane power and power to the outputs must be present to Hold Last State. Otherwise, the module will default outputs regardless of the DIP switch setting.The Outputs Default Mode selection made with the DIP switch must match the selection made for this feature in the module’s software configuration. If the two do not match, a warning message is displayed in the fault table.7-12 PACSystems™ RX3i System Manual – October 2005 GFK-2314CField Wiring: MDL350Connections Terminals Terminals Connections Output 1 1 19 Output 9 Output 1 Supply 2 20 Output 9 SupplyOutput 2 3 21 Output 10 Output 2 Supply 4 22 Output 10 SupplyOutput 3 5 23 Output 11 Output 3 Supply 6 24 Output 11 SupplyOutput 4 7 25 Output 12 Output 4 Supply 8 26 Output 12 SupplyOutput 5 9 27 Output 13 Output 5 Supply 10 28 Output 13 SupplyOutput 6 11 29Output 14 Output 6 Supply 12 30Output 14 SupplyOutput 7 13 31 Output 15 Output 7 Supply 14 32 Output 15 SupplyOutput 8 15 33 Output 16 Output 8 Supply 16 34 Output 16 Supply No connection 17 35 No connection No connection 18 36 No connectionField Wiring TerminalsField Wiring。

PACSystems™ RX3iIC695CMM002 and IC695CMM004 GFK-2461B Serial Communications Modules August 2007communications capabilities of the RX3i system.in the main PACSystems RX3i backplane.module can only be configured for DNP3 Master or Slave.Additional module features include:▪Port-to-port isolation and port-to-backplane isolation▪▪Hardware handshake: RTS/CTS for RS-232▪57.6K, 115.2K▪▪indicators▪▪Flash memory for future upgradesThese modules must be located in an RX3i Universal Backplane.RX3i Serial Communications can be hot-inserted and removedfollowing the instructions in the PACSystems RX3i System Manual,GFK-2314.2 RX3i Serial Communications Modules GFK-2461BRelease InformationThis release is an upgrade of previous version 1.10.Release HistoryRelease UpgradeKitCommentsIC695CMM002-AA IC695CMM004-AA N/A InitialReleaseIC695CMM002-AB IC695CMM004-AB 44A753277-G0244A753278-G02Supports CCM Slave ProtocolIC695CMM002-AC IC695CMM004-AC 44A753277-G0344A753278-G03Supports DNP3 Master and DNP3 Slave ProtocolNew for this ReleaseThis release of the RX3i Serial Module adds support for Distributed Network Protocol 3.0 Master and Slave to the other protocols: MODBUS Master/Slave, CCM, and Serial I/O. This module does not operate with COMMREQs but rather uses preconfigured mappings of the I/O reference memory.MODBUS Master and MODBUS Slave Protocols now support the configuration of 1 stop bit, for compatibility with some GE Fanuc Automation MODBUS Slaves.CompatibilityProgrammer: Proficy® Machine Edition Logic Developer 5.6 with Service Pack 2 SIM 10RX3i CPU: PACSystems RX3i CPU Version 5.00 or later is required to be able to use the timesynchronization feature on a DNP3 Master port.Problems Resolved for This ReleaseWhen parity is set to none in the port configuration for the Modbus Master or Modbus Slave protocols, the stop bits were forced to 2. This restriction has now been removed and the stop bits can be set to 1 or 2.RX3i Serial Communications Modules 3GFK-2461BRestrictions and Open Issues in this Release1. When multiple group objects (i.e. %I and %AI memory) are read in a single request, the DNP3 port willignore all but the first object. Operations of multiple group objects should be split into multiple successiveexchanges (i.e. exchange 1 - %I, exchange 2 - %AI).2. The DNP3 slave port has problems using the link layer to validate frame receipt. The DNP3 organizationencourages users not to do this.3. These modules do not support GE Fanuc special MODBUS commands for use with a Daniels FlowComputer.4. PLC Reference Address and Reference Length Parameters do not support bit length/start. Bit and Non-Byte Length operations must begin on a byte boundary.5. When a port is configured for CCM Slave protocol, and:▪ a new configuration is stored to the PLC using Machine Edition, or▪the system is power-cycled, or▪the module is hot-inserted,if the first query received from the CCM Master is a Read Scratchpad request, the module will reject thatrequest. All subsequent Read Scratchpad requests will be successful unless one of the above conditionsoccurs again.Operating NotesThe maximum resolution for the MODBUS drop delay is 420us, so the minimum time for a drop delay is 420us.Installation in Hazardous Locations•EQUIPMENT LABELED WITH REFERENCE TO CLASS I, GROUPS A, B, C & D, DIV. 2 HAZARDOUSLOCATIONS IS SUITABLE FOR USE IN CLASS I, DIVISION 2, GROUPS A, B, C, D OR NON-HAZARDOUSLOCATIONS ONLY•WARNING - EXPLOSION HAZARD - SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR CLASSI, DIVISION 2;•WARNING - EXPLOSION HAZARD - WHEN IN HAZARDOUS LOCATIONS, TURN OFF POWER BEFOREREPLACING OR WIRING MODULES; AND•WARNING - EXPLOSION HAZARD - DO NOT CONNECT OR DISCONNECT EQUIPMENT UNLESS POWER HASBEEN SWITCHED OFF OR THE AREA IS KNOWN TO BE NONHAZARDOUS.4 RX3i Serial Communications ModulesGFK-2461BSpecifications: IC695CMM002 and IC695CMM004Refer to the PACSystems RX3i System Manual , GFK-2314, for product standards and general specifications.Number of Serial PortsIC695CMM002: two independent serial ports IC695CMM004: four independent serial portsConnectors RJ-45 Number of Serial Communications Modules per CPU Six in the main CPU backplaneIC695CMM002 ********************************************Backplane power requirementsIC695CMM004********************************************LEDs Module OK, Port Fault, Port Status (2 or 4)Port TypeRS-232 or RS-485/22. 4-wire (full duplex) or 2-wire (half-duplex) operation for RS-485/422Flow Control for R-232 Selectable: Hardware (CTS/RTS) or noneBaud rates 1200, 2400, 4800, 9600, 19.2K, 38.4K, 57.6K, 115.2k Parity Even, odd, noneData bits 7, 8 Stop bits1, 2Operating Temperature 0°C to + 60°CInput Impedance Zin > 96 kOhm for RS-485/422 3 kOhm < Zin < 7 kOhm for RS-232 Max Overvoltage +/- 25VChannel-Channel Crosstalk –55dB minimumIsolationPort to Backplane and to frame ground: 250 VAC continuous; 1500 VAC for 1 minute, 2550VDC for one second. Port to port: 500VDC continuous, 710VDC for one minute.In order to meet emission and immunity requirements for the EMC directive (CE mark), shielded cable must be used with this module.RX3i Serial Communications Modules 5GFK-2461BLEDsSerial PortsEach port is a standard RJ-45 female connector with the following pin assignments. For MODBUS applications,note that these pin assignments are different than the standard MODBUS pin assignments. If the port isconfigured for MODBUS master or slave operation, custom cables are needed.6 RX3i Serial Communications Modules GFK-2461BIf the Serial Communications module is communicating with a Series 90-30 CPU363 or external PACSystemsRX3i CPU, the connections are:RX3i Serial Module CPU363/RX3iRD('B')T+ ToT- ToRD('A')SD('B')R+ ToSD('A')R- ToTerminationBy default, each port is set for no termination. Termination is needed if the module is the first or last device on an RS-485 network, even if there is only one other device on the network. Termination can be provided using either an external resistor as shown below or the port’s built-in 120-Ohm termination. If line termination other than 120 Ohms is required, an appropriate external resistor must be supplied.User-Supplied Termination for RS-485Termination using the built-in 120-Ohm resistor can be provided by either setting the appropriate RS-4851. Remove the module’s faceplate by pressing in on the side tabs and pulling the faceplate away from themodule.2. With the module oriented as shown, move either the upper or lower jumper:。

Rx3i PacSystem919-535-3180*******************GE Fanuc IC694TBB032/automation/ge-fanuc/rx3i-pacsystem/IC694TBB032Box Style High Density Terminal Block - 36 Connections IC694T IC694TB IC694TBBHigh-density Terminal BlocksThis chapter describes Terminal Blocks for high-density RX3i modules.Terminal Block Type Catalog Number Box-style Terminal Block, 36 pins, One IC694TBB032Spring-style Terminal Block, 36 pins, One IC694TBS032Extended Box-style Terminal Block, 36 pins, One IC694TBB132Extended Spring-style Terminal Block, 36 pins, One IC694TBS132 Extended High-Density Terminal BlocksExtended High-Density Terminal Blocks IC694TBB132 and IC694TBS132 are functionally-identical to High-Density Terminal Blocks IC694TBB032 and IC694TBS032. The Extended High-Density Terminal Blocks have an outer cover that is approximately ½-inch (13mm) deeper, to accommodate wires with thicker insulation, such as that typically used with AC I/O modules.GFK-2314C 15-115-2 PACSystems™ RX3i System Manual – October 2005 GFK-2314CBox-style Terminal Blocks, 36 Pins: IC694TBB032 and TBB132Box-style Terminal Blocks , IC694TBB032 andIC694TBB132, are used with high-density PACSystemsRX3i modules and equivalent Series 90-30 PLC modules.These terminal blocks provide 36 screw terminals for fieldwiring to the module.Terminal Blocks IC694TBB032 and TBB132 arefunctionally identical. Terminal Block IC694TBB032 comeswith a standard-depth outer cover. When installed, it is thesame depth as most other PACSystems and Series 90-30PLC modules.Extended Terminal Block IC694TBB132 comes with anouter cover that is approximately ½-inch (13mm) deeperthan Terminal Block IC694TBB032, to accommodate wireswith thicker insulation, such as that typically used with ACI/O modules.Specifications: TBB032 and TBB132Torque 7 lb-inWire strip length 0.310 inches (7.87 mm)Wire gauges supported #14-26 AWG (solid or stranded)Connecting Field Wiring to a Box-Style High-density Terminal Block The bottom of the terminal block can be used as a gauge for the wire strip length, as shown below. The stripped wire must be fully-inserted into the terminal block so that the insulation meets the stop position inside the terminal, and the end of the wire is bent. Tightening the terminal screw raises the wire and clamps it in place.GFK-2314C Chapter 15 High-density Terminal Blocks 15-3Spring-style Terminal Blocks, 36 Pins: IC694TBS032 and TBS132 Spring-style Terminal Blocks , IC694TBS032 andIC694TBS132, are used with high-density PACSystemsRX3i modules and equivalent Series 90-30 PLCmodules. These terminal blocks provide 36 spring-styleterminals for field wiring to the module.Terminal Blocks IC694TBS032 and TBS132 arefunctionally identical. Terminal Block IC694TBS032comes with a standard-depth outer cover. Wheninstalled, it is the same depth as most otherPACSystems and Series 90-30 PLC modules.Extended Terminal Block IC694TBS132 comes with anouter cover that is approximately ½-inch (13mm) deeperthan Terminal Block IC694TBS032, to accommodatewires with thicker insulation, such as that typically usedwith AC I/O modules.Specifications: TBS032 and TBS132Wire strip length0.310 inches (7.87 mm) Wire gauges supported#14-28 AWG (solid or stranded)15-4 PACSystems™ RX3i System Manual – October 2005 GFK-2314CInstalling and Removing High-density Terminal BlocksThis section has special installation instructions for High-density Terminal Blocks. See chapter 2 for general installation information. WarningField power must be turned off when installing or removing a Terminal Block assembly. Installing or Removing a Module’s Terminal Block Assembly1. Install the small catalog number label (for example: “ALG600”) supplied with the module inthe slot on the top of the Terminal Block.2. Complete the module wiring and secure the wire bundles to the tie-downs on the bottom ofthe Terminal BlockInserting a Terminal Block in itsCover1. Align the top of the Terminal Block with thebottom of the cover, making sure that thenotches in the Terminal Block match up withthe grooves in the cover.2. Slide the Terminal Block upward until it clicksinto place..GFK-2314C Chapter 15 High-density Terminal Blocks 15-51. 2. 3. Check to be sure the terminalblock is fully seated.Removing a High-density TerminalBlock from the Module1. Open the terminal block door.2. Push the latch down as shown at left veryfirmly until the terminal block is released.3. Pull the terminal block away from themodule until the contacts have separated.Removing a Terminal Block from itsCoverTo remove a Terminal Block from its cover:1. Grasp the sides of the Terminal Block cover.2. Pull down on the bottom of the Terminal Block.。

PACSystems RX3i Controller1 .8Automation & Control SystemsProcess Automation Control SystemsRX3i baseplates are available in 7, 12 and 16 slot configurations to the meet the needs of your application . The RX3i Universal baseplates support hot swap capability to reduce downtime . Expansion bases are available in 5 and 10 slot versions to maximize flexibility .BaseplatesIC695CHS007IC695CHS012 IC695CHS016 IC694CHS398 IC693CHS399 IC694CHS392 IC693CHS393Product NamePACSystems RX3i 7 slot high speed controller base supports only 5 serial bus slots supported . Not expandable .PACSystems RX3i 12 slot high speed controller base supports PCI and serial bus PACSystems RX3i 16 slot high speed controller base supports PCI and serial bus PACSystems RX3i serial 5-slot Expansion Baseplate (serial bus only) PACSystems RX3i serial 5-slot Remote Baseplate (serial bus only) PACSystems RX3i serial 10-slot Expansion Baseplate (serial bus only) PACSystems RX3i serial 10-slot Remote Baseplate (serial bus only) Lifecycle Status Active Active Active Active Mature Active Mature Module TypeUniversal Controller and I/O Base Universal Controller and I/O Base Universal Controller and I/O BaseStandard I/OStandard I/OStandard I/OStandard I/OBackplane Support Supports both PCI and High Speed SerialSupports both PCI and High Speed Serial .Supports both PCI and High Speed Serial .Supports High Speed Serial Only .No PCI support .Supports High Speed Serial Only . No PCI support .Supports High Speed Serial Only . No PCI support .Supports High Speed Serial Only . No PCI support .Module Hot Swap SupportYes Yes Yes No No No No Baseplate OptionController Base and Ethernet Expansion Base .No local base expansionController Base and Ethernet Expansion BaseController Base and Ethernet Expansion BaseExpansionExpansionExpansionExpansionDistance N/A N/A N/A Up to 50 feetUp to 700 feetUp to 50 feetUp to 700 feetNumber of Slots 71216551010Dimension(W x H x D) in . (mm) 10 .43 x 5 .57 x 5 .80 (265 x 142 x 147)18 .01 x 5 .57 x 5 .80 (458 x 142 x 147)23 .7 x 5 .57 x 5 .80 (602 x 142 x 147)10 .43 x 5 .12 x 5 .59 (245 x 130 x 142)10 .43 x 5 .12 x 5 .59 (245 x 130 x 142) 17 .44 x 5 .12 x 5 .59 (443 x 130 x 142)17 .44 x 5 .12 x 5 .59 (443 x 130 x 142)Internal Power Used600 mA @ 3 .3 VDC; 240 mA @ 5 VDC ************;240 mA @ 5 VDC 600 mA @ 3 .3 VDC; 240 mA @ 5 VDC170 mA @ 5 VDC480 mA @ 5 VDC150 mA @ 5 VDC460 mA @ 5 VDC。