DWC-60说明书1

OPERATION AND INSTALLATION MANUAL for 48” REFRIGERATED BACK COUNTER (RBC 48) DIGITAL60” REFRIGERATED BACK COUNTER (RBC 60) DIGITALPlease read this manual completely before attemptingto install, operate or service this equipmentThis manual is Copyright ©2012 Duke Manufacturing Company. All rights reserved.Reproduction without written permission is prohibited. Duke is a registeredtrademark of the Duke Manufacturing Company.Duke Manufacturing Company2305 N. Broadway St. Louis, MO 63102Phone: 314-231-1130 Toll Free: 1-800-735-3853Fax: 314-231-5074 RBC 60RBC 48IMPORTANT WARNING AND SAFETY INFORMATION WARNING: READ THIS MANUAL THOROUGHLY BEFORE OPERATING,INSTALLING OR PERFORMING MAINTENANCE ON THE EQUIPMENT.FAILURE TO FOLLOW INSTRUCTIONS IN THIS MANUAL CAN CAUSEPROPERTY DAMAGE, INJURY OR DEATH.DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORSOR LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE.UNLESS ALL COVER AND ACCESS PANELS ARE IN PLACE ANDPROPERLY SECURED, DO NOT OPERATE THIS EQUIPMENT.CAUTION: OBSERVE THE FOLLOWING:•Minimum clearances must be maintained from all walls and combustible materials.• Keep the equipment area free and clear of combustible material.• Adequate clearance for air openings.• Unit exhausts air to the bottom and the rear.• Do not set unit on a curb or seal to the wall.• Do not block the slots in the front kickplate• Operate equipment only on the type of electricity indicated on the specification plate.• Retain this manual for future reference.Table of Contents: Introduction (4)Serial Number (4)Receiving & Inspecting the Equipment (5)Specifications (5)Installation (5)Location (5)Inside Unit (6)Leveling (6)Stabilizing (6)Electrical Connection (6)Operation (7)Location of Controls (7)Operating Procedure (7)Energy Mode Switch (7)Maintenance (7)Stainless Steel care & Cleaning (7)Cleaning the Condensor Coil (8)Door Gasket Care (9)Drain Maintenance (9)Drain Pan Access (10)INTRODUCTIONThis publication contains information regarding the installation and operation of Duke Refriger-ated Back Counter units. The information contained within applies to the models RBC 48 and RBC 60. Please read this manual completely before attempting to install and/or operate this equipment.Model number RBC 48 describes the 48” wide version of the Refrigerated Back Counter. (Fig. 1)Model number RBC 60 describes the 60” wide version of the Refrigerated Back Counter. (Fig. 2)SERIAL NUMBERAlways have the serial number of your unit available when calling for parts or service.Figure. 1 RBC 48Figure. 2 RBC 60RECEIVING & INSPECTING THE EQUIPMENTCare should be taken during unloading so the equipment is not damaged while being moved into the building.1. Visually inspect the exterior of the package and skid or container. Any damage should be noted and reported to the delivering carrier immediately.2. If damaged, open and inspect the contents with the carrier.3. In the event that the exterior is not damaged, yet upon opening, there is concealed damage to the equipment notify the carrier. Notification should be made verbally as well as in written form.4. Request an inspection by the shipping company of the damaged equipment. This should be done within 10 days from receipt of the equipment.5. Check the lower portion of the unit to be sure legs/casters are not bent.6. Also view compressor compartment housing and visually inspect the refrigeration package. Be sure lines are secure and base is still intact.7. Freight carriers can supply the necessary damage forms upon request. 8. Retain all shipping material until an inspection has been made or waived.SPECIFICATIONSINSTALLATION - LocationUnits represented in this manual are intended for indoor use only. Be sure the location chosen has a floor or counter strong enough to support the total weight of the units. Reinforce the floor or counter if necessary to provide for maximum loading. For the most efficient operation, be sure to provide good air circulation inside and out. These units should be located so that they can be moved for service. Major service to the refrigeration system is done from the end of the cabinet.The outline dimensional drawings for the units are shown in Figures 3 and 4.MODEL DESCRIPTIONVOLTAGE AMPS PHRBC 4848” Refrigerated Back Counter48” Refrigerated Back Counter with Energy Star120 VAC (60 Hz) 230 VAC (50 Hz)120 VAC (60Hz) 220 VAC (50Hz) 6 (max) 3 (max)5.5 (max) 2.5 (max) 1 1 1 1RBC 6060” Refrigerated Back Counter60” Refrigerated Back Counter with Energy Star120 VAC (60 Hz) 220 VAC (50 Hz)120 VAC (60 Hz) 220 VAC (50 Hz) 6 (max) 3 (max)5.5 (max) 2.5 (max) 1 1 1 1MODEL DESCRIPTIONHEIGHT WIDTH LENGTHRBC 48 48” Refrigerated Back Counter40.00 In.29.50 In.48.00 In.RBC 6060” Refrigerated Back Counter40.00 In.29.50 In.60.00 In.INSTALLATION – Inside UnitTake care not to block air flow to the fans and allow space along the front, back and sides.INSTALLATION – Outside UnitBe sure that the unit has access to ample air; avoid hot corners and locations near stoves and ovens.CAUTION:This unit exhausts air to the bottom and the back. Do not seal the unit to the wall or set unit on a curb. The ventilation slots in the kickplate must remain open.INSTALLATION – LevelingBe sure that the units are placed on a firm, flat surface/floor. Check for cracks in flooring or tile and avoid these areas if possible. If necessary place support pads, properly rated for the weight of the unit, to “bridge” uneven or cracked flooring. Level unit accordingly.INSTALLATION – StabilizingUse the leg adjustments to insure that the unit is solid to the floor surface at all four contact points. Insure that the unit does not “rock” when pressure is applied to the top corners.INSTALLATION – Electrical WiringThe RBC 48 and RBC 60 are available as a 120VAC, 60 Hz or as 220VAC, 50 Hz dependent on model. All electrical connections should be performed by a certified electrician and should comply with local electrical codes for your municipality.WARNING:REFER TO THE AMPERAGE DATA LIST IN THE SPECIFICATIONS OR THE SERIAL TAG DATA AND YOUR LOCAL CODE OR THE NATIONAL ELECTRICAL CODE TO BE SURE UNIT IS CONNECTED TO THE PROPER POWER SOURCE. A PROTECTED CIRCUIT OF THE CORRECT VOLTAGE AND AMPERAGE MUST BE RUN FOR CONNECTION OF THE SUPPLY CORD OR PERMANENT CONNECTION TO THE UNIT. THE POWER MUST BE TURNED OFF AND DISCONNECTED WHENEVER PERFORMING MAINTENANCE OR REPAIR FUNCTIONS.Figure. 3 RBC 48Figure. 4RBC 60OPERATION – Location of ControlsThe refrigeration control/temperature setting adjustment is located on the back splash. The energy saving mode switch (if equipped) is located inside the right front access panel. (See figure 5 & 6.) Remove front panel and access plate.These are the only user adjustable components on the unit.OPERATION – Operating ProcedurePress and hold the (i) button to display setpoint. Keep (i) button pressed and use the up/down arrows to adjust setpoint. When the (i) button is released, the new setpoint is stored. To exit from the setup, press the power button or wait 30 seconds. Display will display “dEF” while unit is in defrost mode. Check the cooling specifications required for the products/goods to be stored.Use a simple thermometer to set to a specific temperature. Allow time for temperature chang -es before making a final temperature check.OPERATION – Energy Mode SwitchWhen the mode switch (if equipped) is set to “energy save” mode, the condensate heaters around the door openings are de-energized to reduce power consumption. If condensation forms around the doors, then turn this switch to “normal” mode.MAINTENANCE – Stainless Steel Care & CleaningTo prevent discoloration or rust on stainless steel several important steps need to be taken. Stainless steel contains 70-80% iron which will rust. It also contains 12-30% chromium which forms an invisible passive film over the steels surface which acts as a shield against corrosion. As long as the protective layer is intact, the metal will not corrode. If the film is broken or contaminated, outside elements can begin to breakdown the steel and begin to form rust or discoloration.Figure. 6MAINTENANCE – Stainless Steel Care & Cleaning – cont.Proper cleaning of stainless steel requires soft cloths or plastic scouring pads.CAUTION: Never use steel pads, wire brushes or scrapers.Cleaning solutions need to be alkaline based or non-chloride cleaners. Any cleaner containing chlorides will damage the protective film of the stainless steel. Chlorides are also commonly found in hard water, salts and household and industrial cleaners. If cleaners containing chlorides are used, be sure to rinse repeatedly and dry thoroughly upon completion.Routine cleaning of stainless steel can be done with soap and water. Extreme stains or grease should be cleaned with a non-abrasive cleaner and plastic scrub pad. It is always good to rub with the grain of the steel. There are also stainless steel cleaners available which can restore and preserve the finish of the steels protective layer.Early signs of stainless steel breakdown can consist of small pits and cracks. If this has begun, clean thoroughly and start to apply stainless steel cleaners in attempt to restore the passivity ofMAINTENANCE – Cleaning the Condenser CoilThe condenser coil is located behind the filter panel and is accessed through the front of the unit (See Figure 7). Filter can be cleaned by rinsing with water. Allow to dry completely before reinstalling. The condenser coil requires regular cleaning and is recommended every 60 days. However, in some instances you may find that there is a large amount of debris, dust or grease that has accumulated prior to the 60 day time frame. In these cases the condenser coil should be cleaned every 30 days.Figure. 7MAINTENANCE – Cleaning the Condenser Coil – cont.If the build up on the coil consists of only light dust and debris the condenser coil can be cleaned with a simple brush, heavier dust buildup may require a vacuum or even compressed air to blow through the condensor coil.If heavy grease is present degreasing agents are available for refrigeration use and specifically for the condenser coils. The condenser coil may require a spray with the degreasing agent and then blown through with compressed air.Failure to maintain a clean condenser coil can initially cause high temperatures and excessive run times. Continuous operation with dirty or clogged condenser coils can result in compressor failures. Neglecting the condenser coil cleaning procedures will void any warranties associated with the compressor or cost to replace the compressor.CAUTION:NEVER USE A HIGH-PRESSURE WATER WASH FOR THIS CLEANING PROCEDURE AS WATER CAN DAMAGE ELECTRICAL COMPONENTS LOCATED NEAR OR AT THE CONDENSER COIL. MAINTENANCE – Door Gasket CareGaskets require regular cleaning to prevent mold and mildew build up and also to keep the elasticity of the gasket. Gasket cleaning can be done with the use of warm soapy water. Avoid full strength cleaning products on gaskets as this can cause them to become brittle and prevent proper seals. Also, never use sharp tools or knives to scrape or clean the gasket which could possibly tear the gasket and rip the bellows.Gaskets can easily be replaced and do not require the use of tools or authorized service persons. The gaskets are “Dart” style and can be pulled out of the grove in the door and new gaskets can be “pressed” back into place.MAINTENANCE – DrainEach unit has a copper drain tube located inside the unit which removes condensation from the evaporator coil and deposits it onto a drain pan where it can evaporate (See Fig. 8). If you notice excessive water accumulation on the inside of the unit be sure that the drain tube is connected from the evaporator housing to the condensate evaporator drain pan. If water is collecting underneath the unit you may want to check the condensate evaporator drain tube to be sure it is still located above the drain pan. The leveling of the unit is also important as the units are designed to drain properly when on a level surface, if your floor is not level this can also cause drain problems. Be sure the drain pan is kept free of dirt, dust and other debris as excessive amounts wi ll cause water to back up and overflow from the drain pan.MAINTENANCE – Drain Pan AccessThe drain pan and drain tube can be accessed from the rear of the unit. Pull the unit away from wall to expose the opening in the rear of the cabinet. The drain pan is located under the refrigeration system unit (see fig. 8)NOTES229917 11 10/03/16229917 12 10/03/16Duke Manufacturing Company 2305 N. Broadway St. Louis, MO 63102 Phone: 314-231-1130 Toll Free: 1-800-735-3853 Fax: 314-231-5074 。

DC/DC ConvertersTMDC 60 Series, 60 WattFeatures◆ Fully encapsulated low profile plastic case ◆ Ultra wide 4:1 input voltage range ◆ Operating temperature range–40°C to +85°C◆ I/O isolation 2500 VDC (functional)◆ Excellent efficiency up to 92 %◆ Input filter to meet EN 55032, class A ◆ Optional DIN-Rail mount adapter ◆ No minimum load required ◆ Input polarity protection ◆ Power good LED indicator ◆ Remote On/Off◆ 3-year product warrantyThe TMDC 60 Series is a range of encapsulated high performance DC/DC con-verter modules with ultra wide input voltage ranges. With a very high efficiency of up to 92% and the use of highest grade components these 60 W converters can be operated in an ambient temperature range of -40°C up to 70°C with full load and up to 85°C with 50% load reduction. The EMC immunity is aligned for industrial applications and DIN-rail mount adapters are available as option. Input polarity protection remote On/Off function and power good LED indicator makes this unit to a practical and reliable DC source for any application - Fit and forget!C BSchemeInput current at no load – 24 Vin 5.1 & 12 VDC models:100 mA typ.(nominal input voltage)24 VDC models: 110 mA typ.48 VDC models: 60 mA typ.–48 Vin 5.1 VDC models:40 mA typ.12 & 24 VDC models:60 mA typ.48 VDC models:50 mA typ.Surge voltage (100 msec. max.) 24 Vin models:50 V max.48 Vin models:100 V max.Start up time 50 ms max.Start-up voltage 24 Vin models:9 VDC max.48 Vin models:18 VDC max.Under voltage lockout 24 Vin models:7.5 VDC typ.48 Vin models:16 VDC typ.EMI Conducted EN 55032 class A, FCC part 15 class Awithout external componentsEMI Radiated EN 55032 class A, FCC part 15 class Awith external components/overview/tmdc60 EMC immunity EN 55024–ESD (electrostatic discharge)EN 61000-4-2, air ±8 kV, contact ±4 kV,perf. criteria A–Radiated immunity EN 61000-4-3, 10 V/m, perf. criteria A– Fast transient / surge EN 61000-4-4, ±2 kV, perf. criteria AEN 61000-4-5, ±2 kV, perf. criteria A– Conducted immunity EN 61000-4-6, 10 Vrms, perf. criteria A– Magnetic field immunity EN 61000-4-8, 30 A/m, perf. criteria AVoltage set accuracy ±2.0 % max.Regulation – Input variation Vin min. to Vin max. 1.5 % max.– Load variation 0 – 100 % 1.0 % max.Minimum load not requiredTemperature coefficient ±0.02 %/KRipple and noise (20 MHz Bandwidth) 5.1 VDC models:100 mVpk-pk. typ.12 & 24 VDC models:150 mVpk-pk typ.48 VDC models:200 mVpk-pk. typ.Transient response (alignment to 1% at load step change 75% to 100% )– Recovery time250 µs typ.– Deviation ±5 % max.Over voltage protection 120 % of Vout (Zener diode clamp) Output current limitation at 150 % of Iout max.Short circuit protection hiccup mode, automatic recovery Capacitive load 5.1 VDC models:20‘400 µF max.12.0 VDC models:3’540 µF max.24.0 VDC models:890 µF max.48.0 VDC models:220 µF max.Temperature ranges – Operating ambient with natural convection (20 LFM)–40°C to +85°C (see load derating)– IEC/EN/UL60950-1 approved ambient+60°C max. (without derating)– Case temperature+95°C max.– Storage–50°C to +125°CLoad derating (with natural convection 20 LFM) 3.3 %/K above +70°CThermal impedance – Natural convection 20 LFM 3.5 K/WHumidity (non condensing)95 % rel H max.Reliability, calculated MTBF (MIL-HDBK-217F, at +25°C, ground benign)242’029 hIsolation voltage (60 sec.)– Input/Output2500 VDCIsolation capacitance – Input/Output3000 pF max. (100 kHz, 1 V)Isolation resistance – Input/Output>1000 Mohm (500 VDC)Altitude during operation 2’000 m max.Switching frequency210 kHz typ.Remote On/Off – On: 3.5 to 12 VDC to on terminal 1 or open circuit.– Off:0 to +1.2 VDC on terminal 1 reference to -Vin– Off idle current: 3 mA typ.Safety standards –CB test report UL/cUL 60950-1 2nd edition,IEC 60950-1:2005 (2nd edition)+Am1:2009+Am2:2013, EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013–UL test certificat UL/cUL 60950-1 2nd edition,CSA C22.2 No. 60950-1-07, 2nd Ed.–Certification documents /overview/tmdc60Casing material plastic resin (UL 94V-0 rated)Weight 300 g (10.57 oz)Environmental compliance – Reach declaration /info/reach-declaration.pdf – RoHS directive 2011/65/EUSupporting documents: /overview/tmdc60Dimensions in [mm], () = Inch Terminals: Wires 1.5mm 2 max. Recommended tightening torque: 0.5 to 0.7 Nm (4.5 to 6.2 lb.in.) Case tolerances: ±0.25 (±0.01)。

Thank you for choosing COLBOR product. Please read this manual carefully before use and follow all instructions mentioned herein.CL60Video LightUser ManualSafety InstructionsPlease read and fully understand this manual before using the product.Please remove the COB protective film to avoid damage by overheat before first use.Please remove the COB protective cover to avoid damage by overheat before every use.Do not use the product under moist environment or with wet hands. Do not allow the product to be splashed or soaked in water.Keep the product away from corrosive chemicals and liquid to avoid damage.Keep the product out of children’s reach during use. Do not leave the product unattended.When the product is working, the COB and heat sink will produce high temperature. Do not block, turn upside down and touch with hands.To ensure the service life, the cooling system still runs for a while after shutdown until the COB is below 45℃.Please disconnect the power supply and put away the power cord when it is not in use.During use, arrange the power cord in order to avoid tripping and cutting off the power or damaging the product.Let the product cool completely before storage. Remove the power cable from the product and put it in the corresponding position of carrying bag after cooling down.Do not disassemble the product by yourself, otherwise the warranty will be invalid. If any fault occurs, please refer it to an authorized technician for inspection or maintenance.Recommend to use the original parts of COLBOR. If the product is damaged due to the use of the non-original parts, it is not included in the warranty of our products.Drop or external impact may cause product failure. Artificial damage is not covered by warranty.COLBOR reserves the right of final interpretation of the products. The product design and specifications are subject to change without notice.Product Instructions① COB Bead ② Bead Heat Sink ③ Bowen Mount Adapter ④ Ejector Pin ⑤ Rail ⑥ Vent⑦ Quick-mount Holder ⑧ LCD Display Screen ⑨ Brightness Control Wheel⑩ Color Temperature Control Wheel ⑪ Settings Button⑫ EFF Rate Option Button⑬ EFF Mode Button ⑭ CCT Mode Button ⑮ Type-C Power Input⑯ Power ButtonInstallation & DisassemblyHold the COB protective cover and pull it out as the arrow shows.Note: Make sure remove the cover before every use to avoid heat damage.①Align the inner frame of adapter ring with the outer frame of light, andpush the adapter ring into the light from the head. Fasten two marbles on the adapter ring to the chute.①Slide the quick-mount holder into the chute under the light and rotate the knob a tightly.②Install tripod into the quick-mount holder and rotate the knob b tightly.③Slide the rail of one light into the chute of the other until the pins inlay.Slide VM2 into the chute of light, determine the fixed position and adjust the lever to lock.(1) DC power supply(2) Battery power supplyTurn on power after installing V-mount and battery.Operation Instructions1. Remove COB protective cover2. Install adapter and reflector3. Fixing of the video light4. Multi-light connection & disassembly5. Install VM26. Power supply1. Before using the product for the first time, please be sure to tear off the protective film in front of the COB bead.2. Power On: connect the power cord with the power adapter, plug the connector of adapter into the fixture’s power input, then attach to an electricity supply.3. Function: long press the power button, then the power button lights up. The product enters operation interface.(Factory default mode: CCT)4. Power Off: press the power button.Status Icon DescriptionCCT Mode (Short press CCT Mode Button to enter)operation②Align the reflector with the adapter ring and insert it. The ejector pin is pinched by reflector. Rotate the reflector tightly clockwise and the ejector pin springs back.anticlockwise.Settings1. Short press Settings Button to enter settings menu.2. Roll the Brightness Control Wheel to choose setting.3. Roll the Color Temperature Control Wheel to adjust corresponding setting (Wireless connection adjust need short press).When Group function is on, if the product is operated after a periodof time, it takes time to connect between products, so there will bemillisecond delay.The effective distance of transmitter(TX), receiver (RX), transmitter &receiver (TXRX) is 10 meters.Repeater (RP) function is the auxiliary function to enhance the signal oflight control and the effective distance of light control. However, too manyuses of RP function can affect product response time due to environmentalfactors.If the distance between lights in a group is more than 10 meter, it isrecommended to set a light in the middle as a signal RP point to increasethe control distance. In addition, in the state of multi-light connection, theresponse of the product can be effectively improved when the RP functionof one light is turned on if connected lights are more than five, the RPfunction of two lights are turned on if there are more than ten, and so on.Restore factory settings: long press two wheels together for 5 secondsand the product reboots to restore the factory default mode.SpecificationsColor Rendering IndexColor Temperature RangeBeam AngleIlluminationCOB Output PowerRated PowerLight Working VoltageCooling ModeConnectorBody MaterialLight Dimension (mm)WeightOperating Environment Temperature97+2700K-6500K(±200)≈∠120° Reflector≈∠15°See the Form Below＞60W80W (Max)DC 20V 4ASMART/QUIETType-C, supports PD3.0 20V 4AAluminum Alloy+ABS140*80*90 (Light Base Not Included)Light: 550g Light Base: 160g-10~50℃Packaging ListCL60 Video Lightx1Standard Adapter(Bowens Mount)x1Light Base x1Bowen MouthReflector x1COB protectivecover x1Power Adapter x1Carrying Bagx1User Manualx1WARRANTYWarranty PeriodThank you for purchasing COLBOR products.1. Customers are entitled to free replacement or repair service in case ofquality defect(s) found in the product under normal use within 30 days uponreceipt of the product.2. Original COLBOR products are entitled to 12-month limited warranty service.The warranty period begins on the date of purchase of brand new, unusedproducts by the first end-user.Within the warranty period, if product defect or failure is attributable to materialdefection or technological problem, the defective product or defective part willbe repaired or replaced without charge (service and materials fee).Warranty Exclusions and Limitations1. Faults resulted from inappropriate use of a product without following itsoperation specification2. Artificial damage, e.g. crash, squeeze, scratch, soaking, exposing to rain ordamp3. Modifications to a product by its user or a third party without prior writtenconsent of COLBOR, e.g. replacement of element or circuit, label alteration4. The code on product is inconsistent with that of warranty certificate, or thecode on the product or warranty certificate is altered or torn off5. All consumable accessory attached to a product, like cable, cover6. Faults as a result of force majeure, such as fire, flood, lightning, etc.Warranty Claim Procedure1. If failure or any problem occurs to your product after purchase, pleasecontact a local agent for assistance, or you can always contact COLBOR’scustomer service through email.2. Please retain your sales receipt and warranty certificate as proof ofpurchase. If any of these documents is missing, only sales return or chargeableservice will be provided.3. If the COLBOR product is out of the warranty coverage, the service and theparts cost will be charged.About Product1. After the test, the product with assembly structure has bearing capacity of4kg. Customers need to use according to actual conditions.2. It is recommended to use the original power adapter for power supply.The malfuction will not be included in the warranty if use other equipment topower the product.3. When more than five lights are assembled into a light matrix, turningon the RP function in one of them to provide better control stability. If thenumber of lights reaches 10, enable the RP function for two of them，and soon.Form 1The data is given from testing in a laboratory.IlluminationLight BaseLight BaseLight BaseLight BaseLight BaseReflectorReflectorReflectorReflectorReflector0.5mLUXFCLUXFCLUXFCLUXFCLUXFCLUXFCLUXFCLUXFCLUXFCLUXFC908585356695527797069026037556121041996866010613011006102270610656711259104572795677232330156414536634169115639737186317342439199018543540205919124752301615515022579239167901564270125118055167928432651966518292888268202401886187176185719919666622172073368230217817323722807753m1m5mCCT2700K3200K4300K5600K6500KDownload COLBOR Studio™ APP1.Scan the following QR code to install.2.Search COLBOR STUDIO on App Store or Google Play.COLBOR STUDIORESULT Solved Unsolved Returned(Replaced)Room 2401, 24 / F, South Tower, Lisheng Plaza, No. 68 Huadi Avenue, Liwan District,Guangzhou, China, 510000***********************Guangzhou Zhiying Technology Co., Ltd。

围上。按
键和
键光标可以向前或向后的范围内移动。
FASTER 无 论 光 标 在 本 页 的 什 么 位 置 上 ， 同 时 按
和
键
可以把光标移在本页面上的第一编程范围上。
键盘
键盘被分为 6 个区域： z数 字 键 z屏 幕 页 面 选 择 键 z工 作 模 式 区 域 z指 令 键 z光 标 键 z手 动 模 式 键
编程。该软件完成机器、模具和材料性质计算出来的折
弯先后秩序模拟图像显示。
选 项（ L I N K 7 0 0 0 见 下 面 ）允 许 产 品 输 至 D N C 7 0 0 0 ，D N C 7 0 ，
DNC50 和 DNC60。
LINK7000 软 件 PC900/PC1200 选 项 用 串 行 线 把 产 品 传 输 至 DNC700，
在有非灵敏区域或在没有非灵敏区域的情况下都有高性能闭环调 节 — — 计 数 频 率 ： 250KHZ — — 运 动 速 度 、加 速 度 减 速 度 、调 节 增 益 、PID、安 全 装 置 和 限 位
开关都以数字形式编程在机器参数中 ——自动初始化过程 z电 源 断 电 后 后 挡 料 位 置 保 存 z每 个 产 品 每 个 步 序 对 各 轴 都 有 修 正 值 zRS232 串 行 接 口 （ 供 选 择 ）
数字键盘
数字键及
（负号） 和
入各个范围。
（小数点）键用于把数字或数值输
13
屏幕页面选择键 主菜单键。进入主菜单页面。 产 品 目 录 键 ，又 叫 双 重 功 能 键 。按 该 键 一 次 显 示 内 存 中 的 产 品 目 录 。第 二 次 按 该 键 按 有 关 指 标 页 面 显 示 搜 索 产 品。 产品键。又叫三次功能键。按该键一次显示长度角度 L— α 数 值 。 按 第 二 次 显 示 有 关 挡 料 折 弯 秩 序 。 按 第 三