下载文档原格式
FORESEE（霍斯）F-330350车库门遥控器对码方法
F-330设置面板
一、F-330对码方法：
F-330主机面板共有4个按键（S P + -）和一个一位数的LED数码管显示器。
点按S键，2秒后显示屏右下角指示灯亮，按遥控器任意按键三次，小圆点显示灯闪烁后配码完成。
（按下电机上面"S键"，对码指示灯亮后，在按3下遥控器上面的“锁键”，对码指示灯闪动几下熄灭，遥控器就可以使用了。
【切记不能按S键以外的键】）透明霍斯遥控通道转换方法：有些透明霍斯的遥控器，能够成功正确对码，但是遥控器无法正常使用。
这个时候需要将接收控制通道进行转换，具体方法如下：点按P直到显示5；再按2次+号，然后按住P不松手直到返回到0，此时可以正常使用。
F-350设置面板
二、F-350的对码方法：
F-350主机面板共有4个按键（S P + -）和一个两位数的LED数码管显示器。
初始状态其个位数的外围六段按顺时针流动显示0，十位数不显示。
对码时先按主机面板上的S键，当十位数显示0并立即消
失，再按遥控器任意键两次，主机发出“滴”声，表示对码成功。
三、上下限行程设置：
1、开门上限：按住P键不放，直到显示1，点按P键1闪动，按+或者-键，门体上升或者下降，到达合理位置后点按P键保存。
2、关门下限：点按-键显示2，点按P键2闪动，按+或者-键，门体上升或者下降，关闭至合理位置后，按P键保存。
S M A N U As of date of manufacture, meets all ANSI/UL 325 Safety Requirements for Vehicular Garage Door OpenersM A N U A L C A R E F U L L Y B E F O R E I N S T A L A T I O N O R INSTALLER: Place this manual in the plastic envelope provided andpermanently attach to the wall near the pushbutton.Product Features....................................................2 Tools Required/Component Identification.....2 & 3 Assembly Instructions...........................................3 Identify Your Door Type.........................................4 Important Installation Instructions........................5 Installing the Opener..............................................6 Mounting the Front Bracket............................6 Mounting the Power Head...............................7 Using the Manual Release Mechanism...........7 Installation......................................8 Requirements/Permanent Wiring........9 Control and Auxiliary Equipment........................10 Standard Wall Push Button Installation.......10 Installation of the Super Station...................10 Remote Control Radio System .....................11 TABLE OF CONTENTSOR DEATH. Gives instructions to avoid FCC and IC Radio Operation Statement ......12 Installation of Safe Finish Photosystem.......13 Installation Checklist.....................................14 Operation and Adjustment Instructions............15 Important Safety Instructions.......................15 Basic Operating Parameters.........................15 Testing the Limit Settings.............................16 Testing the Sensitivity...................................16 Testing the Reversing System......................16 Testing the Safe Finish Photosystem...........17 Operating the Super Station Wall Station Wiring Diagram.....................................................18 Auxiliary Equipment Wiring Diagram..................19 Troubleshooting Guide........................................19 Warranty Statement. (20)CAUTION READ THESE STATEMENTS CAREFULLY AND FOLLOW THE INSTRUCTIONS CLOSELY The Warning and Caution boxes throughout this manual are there to protect you and your equipment.Pay close attention to these boxes as you follow the manual.WARNING CAUTION Indicates an ELECTRICAL hazard of DAMAGE to the door, door opener, or equipment. Gives instructions to avoid thehazard .Indicates an ELECTRICAL hazard of INJURY OR DEATH. Gives instructions to avoid the hazard . Indicates a MECHANICAL hazard of DAMAGE to the door, door opener, or equipment. Gives instructions to avoid the hazard . Residential Vehicular Garage Door OperatorMODELS: MVP and MVP-SQSTEPLADDER TAPE MEASUREWOOD BLOCKHAMMERHACKSAW TOOLS REQUIRED FOR INSTALLATION1/2” OPEN ENDWRENCHLEVELSCREW DRIVERSMALL SCREW DRIVER (1/8” HEAD)NOTE:Rail/Chain Assembly is packaged separately from the Power Unit. The Inner Trolley half, Front Idler Sprocket, Chain, and Limit Cams are assembled on the Tee Rail at the factory.Follow the steps outlined below to complete assembly prior to installation. Refer to the component identification illustrations on the previous page.STEP 1: Protect the Power Unit cover fromscratching during assembly by placing it on cardboard. Remove the two 5/16"-18 washered nuts and save them for later use. STEP 2: Position the Tee Rail/Chain Assembly box near the Power Unit. Open the box and locate theInstallation Hardware Packet.STEP 3: Locate the Outer Trolley half (packaged 104363ASSEMBLY INSTRUCTIONSDOOR MOUNTINGFRONT IDLERTROLLEY OUTER CHAIN GUARDWALL MOUNTING BRACKETRELEASE ROPE AND KNOBOPENER HARDWAREBAGTEE RAILRUBBER BUMPEROPENER HEAD UNITPHOTOSYSTEM HARDWARERADIO TRANSMITTERCONTROL WIRESPOOLIMPORTANT!IDENTIFY YOUR DOOR TYPE FROM THOSE ILLUSTRATED BELOW ANDFOLLOW INSTRUCTIONS FOR THAT TYPE OF DOORFOR THESE TYPES OF DOORS USE MODEL MVP OR MODEL MVP-SB. USE 7 FT, 8 FT OR 10 FT RAIL (MATCH DOOR HEIGHT)THE MODEL MVP SERIES IN NOT DESIGNED TO OPERATE THESETYPES OF DOORSone 5/16"-18 washered nut (supplied) Tighten the bolt a MAXIMUM of 1.5 turns after the bolt and nut are Recheck the nuts used to secure the TeeRail to the Power Unit, making sure they are tight. the Chain tension, Chain twist, Chain Guard and the position of both the Close Limit Switch and Open Limit Switch Actuators.CHAIN GUARDACTUATORSPROCKETSPROCKET 104366Assembly is now complete and you are ready to begin installation of the opener.CHAINMASTER LINKOUTER NUTINNER NUTMASTER LINKCHAINDOOR TYPE IDENTIFICATIONONE PIECE DOOR NO TRACKJAMB HARDWAREONE PIECE DOOR NO TRACKPIVOT HARDWAREHIGH ARC OF DOOR TRAVELHIGH ARC OF DOOR TRAVELDOORPIVOT104368TRACKTRACKDOORDOOR104367SECTIONAL DOOR CURVED TRACKONE PIECE DOOR HORIZONTAL TRACK JAMB HARDWAREHIGH ARC OF DOOR TRAVELHIGH ARC OF DOOR TRAVELPower Unit on a ladder or other sturdy support.Open the door to the full open position. Allowsection of the door (as shown in the illustration104372Step 8: Connecting the Door Arm to the Door Type 1: Door Mounted BracketVisually align the door arm connecting hole with the middle hole of the door bracket by rotating the tube section in the appropriate direction.Release the trolley (leave door arm attached) with the manual release cord and pull trolley toward the power head unit. Now rotate the door arm tube section two turns counterclockwise (increasing the exposed length of the door rod) to provide a cushion when the door is closed or encounters an obstruction. Align connecting hole in the door arm to middle hole in the door bracket; insert 3/8” diameter bolt and tighten locking nut, allowing for free pivot of the arm. Note: Do not overtighten locking nut as this will cause binding between the door arm and door bracket.Type 2: Strut Mounted BracketVisually align the door arm connecting hole with the connecting pin of the strut by rotating the tube section in the appropriate direction.Release the trolley (leave door arm attached) with the manual release cord and pull trolley toward the power head unit. Now rotate the door arm tube section two turns counter-clockwise (increasing the exposed length of the door rod) to provide a cushion when the door is closed or encounters an obstruction. Align connecting hole in the door arm with the strut mounted connecting bracket. Insert connecting pin through the hole in the door arm. Secure the connecting pin to the strut bracket according to the manufacturer’s instructions. Note: Door Bracket Mount or Strut Mount - If rod bottoms in cushion tube, cut rod to allow for proper function of this assembly. Set the outer trolley to re-engage, see page 7.Alternate StrutConnecting BracketCut to Fit110054-2Openers are subject to vibration during normal operation which may shorten their life spans.Rough Service bulbs, available at most hardware stores, are recommended. Fit Light Diffuser tabs into the panel slots as shown.On most models, theLimit Cams are installed at the factory. If the Limit Cams have not been installed, or it is necessary to move a Limit Cam to a different link, fasten them to the chain as shown at right in the approximate positions as illustrated below. Position theSwitch Actuators as shown below.104380106428FASTENING LIMIT CAM TOCHAINunder “Special Notes” at the While the LED is. The .LED will blink twice to confirm a valid code and Special Notes - Express CodingRepeat the steps listed above as needed or desired for each button. Each button can be programmed to a unique code, however all three buttons may be programmed at one time (Express Coding). To Express Code, select the “+” button in Step 2, then end the code entry in Step 3 with the “+” button (the first 8 entries can be any random code). The code for each button may be changed at any time.However, if the plus button is programmed as described above, it will replace the existing code settings of the zeroStep 1Step 2Step 3used, slide it into the recess provided on the back of the transmitter caseuntil the snaps on the caseHomeLink® is a registered trade mark of Johnson Controls, Inc. This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept anyPRE-POWER ON-INSTALLATION CHECKLISTBefore continuing with the operation andadjustment section, make sure that:1. The front and rear mounts for the opener aresound and secure and the rail is positionedcorrectly above the high arc of the door, and thatthe opener is positioned over the door actioncenterline.2. For sectional door and one piece door withtracks, the position of the door arm (with thedoor closed), is such that it’s connecting point onthe trolley is 5” to 8” behind it’s connectingpoint on the door bracket. The door arm shouldnever be perfectly vertical when the door in inthe closed position.3. The Manual Release Label and cord are secureto the Manual Release Lever. The handle islocated 6 FT above floor level and requires nomore than a 50 pound pull to activate. Thetrolley and the release mechanism are properlylubricated.4. The standard wall push button or the SuperStation (deluxe wall push button station) is insuch a position and of such a height that it canonly be actuated by an adult of average height.The Control Button Warning label isprominently displayed next to the push button orwall station.5. All wiring is correct to codes or better. There isground continuity form the supply. The groundprong on the power cord is intact.6. All ropes have been removed from the door.The door moves freely without binding whenraised or lowered manually. The door iscorrectly balanced and lubricated. All doorhardware is secure and sound. The sensitivityhas been adjusted to minimum force for theapplication.7. The door reverses on obstructions to within 1.5"of the floor. The concrete or other surfacebeneath the closed door provided uniformcontact.8. The plastic envelope for this manual is attachedto the wall near the push button or wall stationand this manual is placed there for owner useand reference.9. On door with extension type counterbalancesprings, restraint cables have been placedthrough the springs.10. There is Ground Fault Interruption (GFI)protection of the power line to the opener or inthe receptacle.11. On doors with adjustable bottom edges, edgeshave been locked after adjustment.TURNING ON POWER TO THE OPENERNOTE: It is now necessary to turn on the power in order to run the opener to test the operation and check the limit settings. Before doing so, ensure that all mounting hardware is installed and has been properly tightened, that all electrical connections are per local code requirements, and that proper wiring practices have been followed. Also, double-check that all ropes have been removed from the door and that the doorway is clear.BASIC OPERATING PARAMETERS Please note the following Operating Parameters which apply to Openers with Auxiliary Entrapment Protection System (Safe Finish™ Photosystem, Installation Instructions on Page 15) and a standard wall push button connected. Please see page 17 for instructions concerning the Super Station Deluxe Wall Push Button operating parameters.IF THE DOOR IS…...FULLY OPEN, then pushing the standard wall Push Button or the radio control will cause the door to begin MOVING DOWNWARD. ...FULLY CLOSED, then pushing the wall Push Button or the radio control will cause the door to begin MOVING UPWARD....MOVING UPWARD, then pushing the wall Push Button will cause the door to STOP. The next push of the wall button will cause the door to begin MOVING DOWNWARD (Alternate Action Operation)....MOVING UPWARD, then pushing the radio control will cause the door to STOP. The next push of the wall button will cause the door to RESUME UPWARD MOVEMENT (Radio Operation). ...MOVING DOWNWARD, then pushing the wall Push Button or the radio control will cause the door to STOP, PAUSE FOR APPROXIMATELY ONE SECOND, AND THEN BEGIN MOVING UPWARD....MOVING DOWNWARD then reaches the down limit, the lamp will blink off for a 1/2 second then turn back on again, remaining on for 4 minutes 30 seconds and will then automatically turn off....MOVING UPWARD then reaches the open limit, the lamp will remain on for 4 minutes 30 seconds and will then automatically turn off.STEP 3: Testing the Sensitivity Force — To test theSensitivity System, start the Opener and grasp the bottom door handle halfway through the door's travel(opening or closing). When testing in the CLOSEdirection, a second person will be needed to maintainpressure on the Push Button IF an Auxiliary EntrapmentProtection Device has not yet been fitted. If a secondperson isunavailable, use astiff cardboard carton placed in the door's downward path to indicate the force the Opener isOPEN FORCEADJUSTMENTCLOSE FORCE ADJUSTMENT104391THE SENSITIVITY SYSTEM REVERSING TESTENSURE THAT THIS IMPORTANT SYSTEMW A R N I N G1 2 3 4 5 6 7 8 9 Plus Button Zero Button Minus ButtonIF DESIRED, RECORD YOUR RADIO TRANSMITTER CODE POSITIONSETTINGS HERESee Page 11 for Radio System programming instructions and FCC/RSS-210 Industry Canada statement. The opener radio system is HomeLink® compatible.Serial #: Date Installed: Your Dealer:This garage door operatorcomplies with all requirements ofANSI/UL Standard 325.P/N 190-111069 Rev. FX1 August 2007Copyright © 2007 Linear LLC。
车库门发展到现在主要分为遥控、感应、电动、手动几种，而车库门遥控器[1]即为远程控制车库门启闭的装置。
一般来讲，车库门遥控器通常采用遥控器中的无线电遥控器，而非红外遥控器，因为与家电常用的红外遥控器相比，无线电遥控器拥有以下的优点，无线电遥控器是用无线电波来传送控制信号的，它的特点是无方向性、可以不“面对面”控制、距离远（可达数十米，甚至数公里）、容易受电磁干扰。
在需要远距离穿透或者无方向性控制领域，比如车库门遥控控制、工业控制等等，使用无线电遥控器较易解决。
下面对无线遥控器做一个简单的介绍：无线遥控器（RF Remote Control）是利用无线电信号对远方的各种机构进行控制的遥控设备。
这些信号被远方的接收设备接收后，可以指令或驱动其它各种相应的机械或者电子设备，去完成各种操作，如闭合电路、移动手柄、开动电机，之后再由这些机械进行需要的操作。
作为一种与红外遥控器相补充的遥控器种类，在车库门、电动门、道闸遥控控制，防盗报警器，工业控制以及无线智能家居领域得到了广泛的应用。
常用的无线电遥控系统一般分发射和接收两个部分。
发射部分一般分为两种类型，即遥控器与发射模块，遥控器和遥控模块是对于使用方式来说的，遥控器可以当一个整机来独立使用，对外引出线有接线桩头；而遥控模块在电路中当一个元件来使用，根据其引脚定义进行应用，使用遥控模块的优势在于可以和应用电路天衣无缝的连接、体积小、价格低、物尽其用，但使用者必须真正懂得电路原理，否则还是用遥控器来的方便。
接收部分一般来说也分为两种类型，即超外差与超再生接收方式，超再生解调电路也称超再生检波电路，它实际上是工作在间歇振荡状态下的再生检波电路。
超外差式解调电路与超外差收音机相同，它是设置一本机振荡电路产生振荡信号，与接收到的载频信号混频后，得到中频（一般为465kHz）信号，经中频放大和检波，解调出数据信号。
由于载频频率是固定的，所以其电路要比收音机简单一些。
目录介绍 2-7安全标记和信号词 (2)车库门准备 (3)必需的工具 (4)计划准备 (4)纸箱清单 (7)紧固件清单 (7)装配 8-14装配导轨和滑套 (8)将导轨固定到电机单元上 (9)安装导向滑轮 (10)安装链条/钢丝绳 (11)拉紧链条 (14)安装 15-40重要的安装说明 (15)定位头部支架 (15)安装头部支架.........................................21安装墙壁开关. (28)安装灯泡 (29)安装紧急释放绳和手柄 (30)安装电源 (30)安装保护系统 (31)固定门支架 (34)连接门臂到滑套上 (36)调整 41-43力的调整 (41)门位置的调整 (41)安全反转系统测试 (42)操作 44-51重要安全说明 (44)使用开门器 (45)使用墙壁开关 (46)手动开门 (46)开门器的保养 (47)您有问题吗？ (49)将导轨安装到头部支架遥控器编程 52上 (23)固定开门器 (24)悬挂开门器 (26)说明安全标记和信号词本车库门开门机只有严格按照本说明书进行安装，使用，检修与检查才安全可靠。
当你在后面看到这些安全标记和信号词时，他们将警告你如果你不遵守这些警告事项将可能导致严重的伤害或死亡，这些可能是由机械或电所致，仔细阅读警告事项。
当你在后面看到这些信号词时，它将警告你如果不遵守这些注意事项可能会破坏车库门和/或开门器，仔细阅读它们。
车库门准备安装开始前：●去掉锁；●去掉任何连接在车库门上的绳索；●完成以下测试来确定门是否已经被调平衡，以及能否正确的开启和关闭：1、让门停在开启一半的位置，松开手，如果门能够被扭簧支撑而停住，说明门已经调试平衡。
2、开启和关闭门，看是否有卡夹现象如果门被卡住，或没有调试平衡，请打电话给专业安装人员。
必需的工具在开门器的装配、安装和调试过程中，需要图示中的手工具计划准备确定门的类型和重量，测量门的面积，看符合以下那种安装条件，可能需要额外的材料，你会发现这些对你安装开门器是很有用的。
自动开门机•资料.使用说明书标准技术参数◊机箱材料：国产标准45钢◊传动臂角度：180度◊开门方向：单向◊工作电压：AC220 ±10% V/50 ±10% HZ◊驱动电机：24V直流有刷电机◊输入接口：干接点信号O开、关门时间：仁9秒（可调）◊上电后进入通行状态所需时间：3秒◊工作环境：室内、室外（阴棚）◊温度：-1CTC一一50°C相对湿度：＜90%,不凝露—、安装说明1、设备的安装：开门机中预埋铺设RVV4X0.75mm2信号线及2X1.5mm2控制线。
并将控制线接至控制室。
用四个膨胀螺丝按下图底座安装尺寸将开门机固定。
设备安装尺寸图2、设备接线安装1） 输入接口： OPEN 、GND 为干接点短路信号； 2） 接线排的连接：按接线排的标识接好电源和开闸信号; 与门禁控制板、出门按钮、 电锁电路连接图 出门按钮锁负 锁正 口吁亠以口 nE J fe GND OPEN用户门禁控制板端子mGND +12V 丄X 磁力锁电轍(<2A) l=fl~采删加 >训玮殲―祠 ORW2X0.5mm^t^B1if ：哪号飆娜餓購序銀CJE'Z-- •—・■• — ------- -- - - ------- --T卫L3J控制箱内接线端注明：仁提供的开闸信号接法：干接点信号：GND为公共端，OPEN和GND短接就分别开信号；2、将磁力锁的正极(+12V)和负极(GND),分别接入控制箱内。
3、检查接线是否与接线图一致，检査所有插头是否有松动；检査设备是否接地可靠；确认无误后可上电调试。
3> 注意事项：未经许可，设备上请勿添加外围设备且确保设备接地可靠，保证设备工作的安全可靠;二、设备参数设置操作说明一、通用描述1.显示屏是指主控板上的从左到右显示的2位LED：2.三个按键从左到右依次为INC键，DEC键，SET键，SET键用于进入和退出功能设定；INC键用于对需要设定的参数进行加1； DEC键用于对需要设定的参数进行减1,或退出菜单（显示01时按DEC键退出菜单）；当要进入某项功能号时按SET键，此时显示屏显示2位当前功能号参数并闪烁，表示可以用INC键（+ ）, DSC键（一）对此功能号参数进行修改, 修改完成后按SET键退出此项参数设置。
车库门发展到现在主要分为遥控、感应、电动、手动几种，而车库门遥控器[1]即为远程控制车库门启闭的装置。
一般来讲，车库门遥控器通常采用遥控器中的无线电遥控器，而非红外遥控器，因为与家电常用的红外遥控器相比，无线电遥控器拥有以下的优点，无线电遥控器是用无线电波来传送控制信号的，它的特点是无方向性、可以不“面对面”控制、距离远（可达数十米，甚至数公里）、容易受电磁干扰。
在需要远距离穿透或者无方向性控制领域，比如车库门遥控控制、工业控制等等，使用无线电遥控器较易解决。
下面对无线遥控器做一个简单的介绍：无线遥控器（RF Remote Control）是利用无线电信号对远方的各种机构进行控制的遥控设备。
这些信号被远方的接收设备接收后，可以指令或驱动其它各种相应的机械或者电子设备，去完成各种操作，如闭合电路、移动手柄、开动电机，之后再由这些机械进行需要的操作。
作为一种与红外遥控器相补充的遥控器种类，在车库门、电动门、道闸遥控控制，防盗报警器，工业控制以及无线智能家居领域得到了广泛的应用。
常用的无线电遥控系统一般分发射和接收两个部分。
发射部分一般分为两种类型，即遥控器与发射模块，遥控器和遥控模块是对于使用方式来说的，遥控器可以当一个整机来独立使用，对外引出线有接线桩头；而遥控模块在电路中当一个元件来使用，根据其引脚定义进行应用，使用遥控模块的优势在于可以和应用电路天衣无缝的连接、体积小、价格低、物尽其用，但使用者必须真正懂得电路原理，否则还是用遥控器来的方便。
接收部分一般来说也分为两种类型，即超外差与超再生接收方式，超再生解调电路也称超再生检波电路，它实际上是工作在间歇振荡状态下的再生检波电路。
超外差式解调电路与超外差收音机相同，它是设置一本机振荡电路产生振荡信号，与接收到的载频信号混频后，得到中频（一般为465kHz）信号，经中频放大和检波，解调出数据信号。
由于载频频率是固定的，所以其电路要比收音机简单一些。
霍斯F-330车库门开门机调试说明书来源:车库门时间:2013-07-25 14:02调试方式非专业人员禁止调试、调试准备1移动门板，直致离合器锁上，以使开门器在调试过程中可直接牵动门板。
2接上电源，照明灯亮。
电机发出“嘟” 一声，显示窗口出现0字并循环转动。
（注意：当用户进入程序三分钟后不按键，程序会自动退出；另当设置程序错误时，可先将电源关闭，再开启，按以下步骤重新设置。
）二、显示模式CD +S遥控配码消码键。
P功能键与储存“ +”“ - ”调节键1上行程设置点按p键不放手（约5秒），“嘟”一声显示屏出现1，按“ + ” / “- ”键设置上行程，设置完毕按p键，储存并显示“ 2”。
2下行程设置S ■=■丄■」n厂At按“ + ” / “-”键设置下行程，设置完毕按p键。
储存并显示“ 3”3运行阻力曲线跟踪自动下降。
在此过程，电脑自动跟踪运行阻力，编写阻力曲线。
（一般用户此时再按p键不放手，5秒后显示“0”，即可退出设置程序，完成开门器的基本设置）。
按下遥控器开门器可正常运行（注：用户必须完成以上调试步骤后退出程序，所有设置才有效）4阻力设置。
注：出厂时已设置，默认第四级，一般用户无须此设置点p键，显示屏出现4再按“ + ”键，或“-”键设置阻力完毕后按p键，储存并显示“ 5”。
（注：用户选择反弹力过大或过小会影响车库门运行不稳定）5遥控上下键切换（备注：此功能可用一个遥控器上的不同按键控制2台开门器）按“ + ”键，上键控制车库门。
按“-”键，下键控制车库门，点按p键出现66自动关门功能点按“ + ”键2次，出现1表示自动关门开启。
按“-”键出现0表示关闭。
自动关门功能开启后，过5分钟开始自动关门。
关门前20秒，蜂鸣器响及指示灯闪烁。
一、钢架的安装用标准规格的钢架立于洞口的两侧，保证钢架的垂直度和水平度，然后用10个M10×110㎜的膨胀螺栓固定到墙壁上，保证每个点能承受1000N的垂直拉力而不脱落、不松动，并注意避开轨道固定件的安装位置。
二、轨道的安装根据门板的宽度和高度确定两轨道固定件的位置并用水平管测水平，再用M8×41㎜的方头螺钉固定。
用卷尺测准水平轨与墙壁及两水平轨之间的间距，用水平尺测准水平轨的水平，然后用M6.4×14㎜的小帽螺丝和六角螺帽将水平轨连接件与水平轨和轨道固定件连接固定。
用带眼角钢制成两个三角架，然后将其与水平轨的末端用M6.4×14㎜的小帽螺丝、螺帽连接，并用M8×70㎜的膨胀螺栓固定到天棚或墙壁上。
三、扭簧的安装将扭簧中心支架、尼龙胶圈、固定法兰、与门体重量相匹配的扭簧、锁紧法兰、绕线轮、轴承支架按顺序（分清左右侧）套在镀锌钢管上，并注意各零部件是否安装正确。
用M8×41㎜的方头螺钉将扭簧中心支架固定到洞口上部中间位置的短木板上，并注意避开链盒的安装位置。
用M8×40㎜的螺栓将扭簧中心支架、尼龙胶圈、固定法兰和扭簧连接，再将扭簧和锁紧法兰连接。
然后将轴承支架的下端用M9.5×19㎜的大帽螺丝和螺帽与水平轨连接件连接固定，轴承支架的上端用M8×41㎜的方头螺钉固定到侧木框上。
四、门板的安装将底密封条放到底门板的底部，并用M4×16㎜或M6.4×16㎜的自攻钉将其从背面固定到门板上。
将底轮支架放到门板的两侧*近底密封条的位置，1＃折页分别放到门板顶部的左中右三个位置上（宽度低于10英尺，中间位置是一个；宽度在10英尺至14英尺，中间位置是二个；宽度在15英尺至18英尺，中间位置是三个），并分别用M6.4×16㎜的自攻钉固定。
然后将滚轮涂上甘油穿入底轮支架和1＃折页中，将此门板放到立好的轨道里并使其水平。
车库门是企业的常用设施，适用于商业门面等，常见的车库门主要有遥控、电动、手动几种。
其中遥控、感应、电动都可统称为自动车库门。
手动车库门和自动车库门主要区别是没有电机。
自动车库门现在主要分类为：翻板车库门与卷帘车库门。
尤其是门洞较大，不便安装地面门体的地方起到方便、快捷开启作用。
车库门的安装一般比较繁琐，需要专业人士进行操作。
以下是中博门业提供的车库门安装步骤。
希望能给大家带来帮助。
1、量出门板与洞口宽度，确认洞口两侧边沿到门板边沿所预留的尺寸。
并在门垛上做出标记。
2、立直轨：在门垛上的标记处向墙壁方向15mm处做另一个标记，直轨里口应与此标记对齐。
先安一侧直轨，另一侧直轨安装前要在两顶口找一水平。
为使门板运行自如，直轨并非垂直地面而是略向库内倾斜，倾斜角度以门体上下运行协调顺畅为原则，可在门板安完之后再调节。
3、找到底板，上好底密封，底轮架。
将铰链下半部分先固定在底板上，注意铰链号码应为自下而上排列。
4、将两块门板放入直轨，固定铰链，然后将门板找水平，确认水平后，即可上第三、四块门板，每块门板要两端对齐，后面一块门板不安装。
5、安装平衡系统：在门顶两侧固定吊架角铁，将弹簧及调整法兰、固定法兰、中间支架、两侧钢丝轮、两侧轴承支架套上钢管后把整个平衡系统擎起，将轴承支架固定在吊架角铁上并在墙壁上固定中间支架，为避免安装电机时出现障碍，中间支架位置应偏左100mm。
6、架弯轨：用直板连接直弯轨接口，在轴承支架与弯轨之间连接吊架角铁，装上一侧弯轨后，要将此弯轨确认水平后在固定。
另一侧弯轨自身可不测水平，只需在顶端处与第一根弯轨找一次水平即可。
7、安装最后一块门板，上顶轮架，顶滑轮距离调整以第五块门板能够靠近洞口为准。
8、配重：用撬杠绞扭弹簧，一般为6-8圈，不可过强过弱，原则上门体运行不畅亦加重电机负担，将钢丝绳底端套住底轮架，顶端套在钢丝轮上，确认两边钢丝绳松紧度一致后在钢管上固定钢丝轮。
9、由法兰中撤出撬杠，此过程应使一人下扳门板，令门体缓慢上升，使门体在运行过程中钢丝绳环绕钢丝轮，在凹槽内逐一归位，切不应产生窜扣现象。
