HP-CP1025-M175拆装机-对位.doc
- 格式:doc
- 大小:606.00 KB
- 文档页数:3
HPM1005更换部件拆机图解(英⽂版)6Removal and replacementThis chapter provides information about the following topics.●Removal and replacement strategyENWW59Removal and replacement strategyNOTE Some photos show a device other than the HP LaserJet M1005 MFP. Repair andreplacement procedures in this chapter are for the HP LaserJet M1005 MFP and are not affectedby cosmetic differences (for example, the color of the covers) shown in these photos.This chapter documents the removal and replacement of field replaceable parts (FRUs) only.Reinstallation is generally the reverse of removal. Occasionally, notes and hints are included to provide directions for difficult or critical replacement procedures.AdmonitionsWARNING!Unplug the power cord from the power outlet (at the wall receptacle) beforeattempting to service the device. It this warning is not followed, severe injury can result. Certainfunctional checks during troubleshooting must be performed with power supplied to the device.However, the power supply should be disconnected during removal.Sheet-metal and plastic edges in the device can be sharp. Use caution when servicing this device.Never operate or service the device with the protective cover removed from the laser/scannerassembly. The invisible reflected beam can damage your eyes.CAUTION The device contains components that are sensitive to electrostatic discharge (ESD).Always perform service work at an ESD-protected workstation. If an ESD-protected workstationis not available, discharge body static by grasping the print engine chassis before touching anESD-sensitive component. Ground the print engine chassis before servicing the device.CAUTION Do not bend or fold the FFCs during the removal or reinstallation process.NOTE For service purposes, the upper part of the HP LaserJet M1005 MFP is, in effect, the"scanner" and the lower part is the "printer". Together, they also act as a photocopier, but theservice description here is simplified by referring to copier functionality only when specificallynecessary.Tip To install a self-tapping screw, first turn it counterclockwise to align it with the existing threadpattern, then carefully turn it clockwise to tighten. Do not overtighten.Required tools●#2 Phillips screwdriver with magnetic tip●Small flat-blade screwdriver●#8 and #10 torx screwdrivers●Needle-nose pliers●ESD mat (if available)●Penlight (optional)●Long flat-blade screwdriver (optional)60Chapter 6 Removal and replacement ENWWCAUTION Do not use a pozidrive screwdriver or any motorized screwdriver. These can damagescrews or screw threads on the device.Before performing service●If possible, print a configuration page (to record customer settings) and menu structure report.See Troubleshooting tools on page 140.●Remove all media from the device and remove the media input tray. See Media input trayon page 78.●Turn off the power by using the power switch.●Unplug the power cord from the wall receptacle.●Place the device on an ESD mat, if available. If an ESD-protected workstation is not available,discharge body static and ground the print engine chassis before servicing the device.●Remove the print cartridge.After performing service●Replace the print cartridge.●Reload the input tray with media.●Restore customer configuration settings.Parts removal orderUse the following diagrams to determine which parts of the device must be removed before servicing. ENWW Removal and replacement strategy61Control panel overlayControl panelScanner lidScanner assemblyLink assembly and scanner springPrinter separation padPrint cartridgePrinter pickup rollerTransfer rollerMedia input trayPrinter side coversRear cover and fuser coverPower supplyScanner assemblyPrint-cartridge doorFront coverScanner support frameEngine controller unitLaser/scanner assemblyMain motorFuser assemblyPaper pickup assemblyFront coverFormatterFigure 6-1 Parts removal order for the HP LaserJet M1005 MFP62Chapter 6 Removal and replacement ENWWFlatbed lid1.Open the flatbed lid.2.Lift the lid up and off of the scanner assembly to remove it.NOTE The lid must be in the fully opened position to release the hinge pins from the hinge brackets.Figure 6-2 Remove the flatbed lid (1 of 2)Tip When the flatbed lid is reinstalled, make sure that the hinge pins are fully seated inthe hinge brackets on the scanner flatbed assembly.ENWW Removal and replacement strategy63Control-panel overlayUse a small flat blade screwdriver to lift up the control-panel overlay and then remove it.CAUTION Be careful to not damage the overlay if it will be reinstalled after servicing the device.Figure 6-3 Remove the control-panel overlay64Chapter 6 Removal and replacement ENWWControl panelTip Lift up the control-panel overlay to see the screw. See Control-panel overlay on page 64.Figure 6-4 Remove the control panel (1 of 4)1.Remove one screw.Figure 6-5 Remove the control panel (2 of 4)ENWW Removal and replacement strategy652.Slide the control panel toward you and slightly lift up the control panel.Figure 6-6 Remove the control panel (3 of 4)3.Disconnect one flat flexible cable (callout 1) and remove the control panel.Figure 6-7 Remove the control panel (4 of 4)Tip When reinstalling the control panel, make sure the rear mounting tabs on the bottom rear of the control panel engage the holes in the scanner assembly, and then slide the control panel toward the rear of the device.66Chapter 6 Removal and replacement ENWWScanner assembly1.Remove the flatbed lid. See Flatbed lid on page 63.2.Remove one screw (callout 1).Figure 6-8 Remove the scanner assembly (1 of 11)3.Gently pry the side cover away from the device chassis.Figure 6-9 Remove the scanner assembly (2 of 11)ENWW Removal and replacement strategy674.Release the side cover bottom locking tab and remove the cover.Figure 6-10 Remove the scanner assembly (3 of 11)5.Disconnect two FFCs (callout 2).Figure 6-11 Remove the scanner assembly (4 of 11)68Chapter 6 Removal and replacement ENWW6.Push the print-cartridge-door button and raise the scanner assembly.Figure 6-12 Remove the scanner assembly (5 of 11)7.Remove the shield and the FFCs from the guide (callout 3).NOTE The screw (callout 4) that fastens the shield to the device chassis does not needto be removed.Figure 6-13 Remove the scanner assembly (6 of 11)ENWW Removal and replacement strategy698.Release the tab on the gear-drive arm bracket and carefully flex it away from the scanner assembly.Figure 6-14 Remove the scanner assembly (7 of 11)9.Pull the bracket toward the right side of the device until its mounting tabs clear the holes in thescanner assembly.Figure 6-15 Remove the scanner assembly (8 of 11)70Chapter 6 Removal and replacement ENWW/doc/e46440e0856a561252d36f48.html e a small flat-blade screwdriver to release the hinge tabs on each front hinge (right side shown).WARNING!When the front hinges are disengaged, the scanner assembly can easily falloff of the device base if it is rotated too far toward the back of the product.CAUTION Do not push too hard on the link tabs or the tabs might break.Figure 6-16 Remove the scanner assembly (9 of 11)11.Remove the hinges (right side shown).Figure 6-17 Remove the scanner assembly (10 of 11)ENWW Removal and replacement strategy7112.Rotate the scanner assembly toward the rear of the product until the rear hinges clear the chassis hinge pins. Lift the scanner assembly up and off of the device base.Figure 6-18 Remove the scanner assembly (11 of 11)72Chapter 6 Removal and replacement ENWWDevice separation padNOTE Some photos show a device other than the HP LaserJet M1005 MFP. Repair and replacement procedures in this chapter are for the HP LaserJet M1005 MFP and are not affected by cosmetic differences (for example, the color of the covers) shown in these photos.1.At the back of the device, remove two screws (callout 1).Figure 6-19 Remove the device separation pad (1 of 2)2.Remove the device separation pad and frame.Figure 6-20 Remove the device separation pad (2 of 2)ENWW Removal and replacement strategy73Print cartridgeCAUTION To prevent damage, do not expose the print cartridge to direct or bright light. Cover it with a piece of paper.1.Push the print-cartridge-door button to release the print-cartridge door.Figure 6-21 Remove the print cartridge (1 of 2)2.Pull the print cartridge up and out of the device.Figure 6-22 Remove the print cartridge (2 of 2)74Chapter 6 Removal and replacement ENWWDevice pickup roller1.Remove the print cartridge and locate the device pickup roller. See Print cartridge on page 74.Figure 6-23 Remove the device pickup roller (1 of 5)2.Gently release the small, white tabs on each side of the pickup roller by pushing them away fromthe roller, and then rotate the roller away from the mounting frame.CAUTION Do not touch the black-sponge transfer roller inside the device. Touching the transfer roller can damage the device.Use gentle pressure to release the small white tabs to avoid breaking them.Figure 6-24 Remove the device pickup roller (2 of 5)ENWW Removal and replacement strategy753.Gently pull the roller up and out of the device.Figure 6-25 Remove the device pickup roller (3 of 5)4.Circular and rectangular pegs on each side of the pickup roller fit into corresponding slots on the pickup-roller mounting frame to prevent the roller from being incorrectly installed. Position the replacement pickup roller in the slots on the pickup-roller frame.Figure 6-26 Remove the device pickup roller (4 of 5)76Chapter 6 Removal and replacement ENWW5.Rotate the top of the pickup roller into position until the white tabs on each side of the roller snap into place.Figure 6-27 Remove the device pickup roller (5 of 5)ENWW Removal and replacement strategy77。
中国惠普惠普激光产品故障诊断和排除手册中国惠普PPS CSS维修中心专用中国惠普PPS CSS 技术委员会2012-10-23针对激光产品的各种常见故障现象,提供相应的解决方案。
目录更新说明: (5)第一章:总则 (6)第二章:通用故障检查和排除方法 (7)第一节:加电问题 (7)第二节:纸路问题 (7)第三节:USB连接问题 (7)第四节:打印质量问题 (8)第五节:复印扫描问题 (8)第六节:传真问题 (8)第七节:其它问题 (9)第三章:产品不加电 (10)第一节:P1007/P1008/M1136/M1213/M1216不加电 (10)第二节:LJ1020/LJ1020PLUS不加电 (10)第三节:M1319不加电 (11)第四节:CP1215/CP1515/CP1518/CP1525不加电 (12)第五节:CM1415FN/cm1415FNW不加电 (13)第六节:CP1025不加电 (14)第四章:产品开机不就绪及打印报错 (15)第一节:LJ1020+ 开机不就绪 (15)第二节:P1007/P1008 开机不就绪 (15)第三节:M1213/M1216 开机不就绪 (16)第四节:M1319 开机不就绪 (19)第五节:M1536开机不就绪 (21)第六节:CP1025 开机不就绪 (22)第七节:CM1415 开机不就绪 (23)第八节:M175开机不就绪 (26)第九节:M1136 错误代码说明 (28)第十节:CP1025状态指示灯故障说明 (31)第五章:联机或连接问题 (35)第一节:M1319联机问题 (35)第二节:CM1415 联机问题 (35)第六章:纸路问题 (37)第一节:单功能黑白激光纸路问题 (37)第二节:彩色激光纸路问题 (39)第七章:打印质量问题 (45)第一节:黑白激光打印质量问题 (45)第二节:彩色激光打印质量问题 (48)第三节:重复性等距离打印缺陷 (54)第八章:复印扫描问题 (58)第一节:扫描故障错误 (58)第二节:复印全黑 (60)第三节:打印正常、复印有底灰 (60)第四节:M1536/CM1415 ADF故障现象 (61)第九章:传真问题 (63)第十章:噪音问题 (67)第十一章:软件和使用问题 (68)第十二章:加热组件及其它 (72)第一节:加热组件问题 (72)第二节:打开M1213/M1216 ADF上盖时,扫描平台自动弹起 (73)第三节:如何查看LJ1020+ 的打印量和Service ID (75)附录A:激光打印机拆机要点 (76)第一节:黑白激光产品搓纸轮和分页器拆卸方法 (76)第二节:彩色激光打印机搓纸轮的拆卸方法 (76)第三节:CP1025/M175拆装注意事项 (81)附录B:水货/假货判断 (87)第一节:检查方法 (87)第二节:根据产品序列号判断 (88)第三节:P1005/P1006冒充P1007/P1008 (90)第四节:P1106/P1108冒充P1007/P1008 (92)第五节:CP1025 水货/假货鉴别 (94)第六节:M1536 水货/假货鉴别 (96)第七节:M1213水货/假货鉴别 (96)更新说明:2012-01-16:正式发布《惠普激光产品故障诊断和排除手册》第一版。
富士施乐深度拆解 XEROX CP105B本来说前几日要传图,工作有点忙,今天才基本整理好不管是给鲜花还是拍砖头,大家权作见见新鲜,懂技术的朋友多多交流先将XEROX CP 105B家族的族谱列下1、XEROX CP105B2、XEROX CP205B3、XEROX CM205B(彩色一体机)4、XEROX P105B(黑白机)5、XEROX M105B(黑白一体机)这几款机型同时使用的是SLED成像技术,LED大家估计都比较熟悉啦,OKI的最爱XEROX 在前面加了个S,估计就是SUPER的意思,也就是超级吧(这里的是猜想,具体是不是关系也不大)在此之前OKI推出过低端的LED成像设备“OKI B2200”,说实话样子很小,销量很少,价格很高,耗材很贵基本上可以说是不太成功;XEROX的这个机器估计也汲取了OKI的教训,在机器外观上下了功夫总体这几款外观都还不错,而且低端的P105B还没有芯片,同时还把终身免换硒鼓作为噱头来宣传同时还请了梁大官人来做代言,可见扎本不小,所以对这个系列的机型确实有必要好好了解一起学习吧,本人也是第一次拆这款机型,相机效果也一般,保证看的见,觉得看不清者自己可从新拆过。
废话不讲啦,上图吧交流再引玉一次2 机器正面视图(我的是港行CP105B,黑色机身,国行的颜色和这个不一样)3 先取下纸盒托纸板一边的卡位,(以前也试过从后面拆,发现不行)4 取掉托纸板两边的卡位,即可拿掉托纸板;然后拆掉红圈中两个螺丝,即可取掉前盖5 取掉前盖的CP105B6 前盖拿掉后即可取下上盖(卡位连接),电源板与高压板的靓照!7 拆下机器左边外壳,即可看到主板(红框中)8 拆后盖过程中,看到后门传感器,留念一张,上次从后面拆时就是这个东西有连线拆不下9 给连接板拍下,以防线序错乱(我就这么叫吧,也不知标准名字是什么)10 定影组件左边的螺丝,关于这个螺丝没有专用工具拆确实费劲,不过还是拆下来啦11 给这个破螺丝来个特写!12 同时给定影组件来个近距离特写未完待续[原创]深度拆解XEROX CP105B13 给高压板来个特写14 左边四个黄色圈中就是粉盒芯片读取装置的连线15 怕记不清,再给连接板来个图16 图中红框内是有个板子的,SLED头的排线就接在上面,我们姑且叫做SLED控制板吧17 拆掉电源板等几块板子后就可以看到部分转印带,先不管,直接往下拆,我们要的是整个全看到18 图中排线就是其中SLED头排线中的一条19 终于看到整个转印带啦,先咔嚓一张,再“修理”它20 排线卡21 红色的为主驱动电机,黄色的为纸盒离合器22 离合器以及耦合齿轮23 目的之一,还拆掉的整个显影组件,过程没有记录;红色圈中的黄色塑料杆是用来清洁每个SLED头的,后面还有对应每个清洁孔的位置24 这次是真的全部拆下来,TMD,是一体的,想拆开不太容易,但已经到了这个份上啦,就稍微拆一下啦待续这时候应该抽支烟,写的比拆的还累25 可以看到鼓芯啦,和C1110B颜色差不多,不知道终身不换是否可行 [em87]26 四个颜色圈中就是SLED头清洁杆的入孔,很小但正合适;主要不要插反27这个就是SLED头了,和OKI的差不多,就没有整个拆下来28 不过我还是拆下了一个显影仓,黄色的29 拆下来的定影组件和点烟用的火机哈哈,30 拨开显影辊表面,可以确定是金属棍至此拆机完成,总计一下,这款机器总体设计还是不错,纸路相对简单,体积也很合理,比老的HP1020大不了多少,另外这款机器采用一体式高集成度成像单元(鼓芯显影仓SLED头转印带),如果其中某一个配件坏掉,更换起来就很麻烦,这样看来施乐的终身不用更换硒鼓也是被逼的,这样设计你是想换都换不了;由于这个显影仓是有载体,所以外置的粉盒其实是一个和成像没有太大关系的盒子,因此粉变的尤其重要;所以针对此机再生选粉是关键!!。
激光打印机主要由激光扫描系统、成像转印系统、机械传动系统、传感器和电路等部分构成。
4.1 激光打印机外壳的结构与拆卸
图4-1所示为激光打印机(HP LaserJet 2200D )的整机结构,从图中可以看出激光打印机的基本结构和组成。
图4-1 激光打印机的整机结构
激光打印机是由激光系统、显影系统、定影系统、走纸系统和系统控制电路等部分组成的。
图4-2所示为激光打印机的内部结构。
下面以惠普(HP LaserJet 2200D )激光打印机为例,介绍一下激光打印机外壳的拆卸方法。
拆卸激光打印机之前,应先将激光打印机的上盖打开,从机体中取出显影系统,并将激光打印机的自动输纸纸盒取出,如图4-3所示。
激光打印机的右侧由螺钉和卡扣固定,将螺钉拧下后,拨动卡扣即可将右侧盖板从整机上取下,如图4-4所示。
1、打印头故障主要表现为缺针与打印点薄或打印不清:此故障表现为缺针现象,当打印机出现此类故障时(某些故障中可出现1#、2#或多根针不出针情况);可主要分三个方向查询故障原因。
一、主板不良(针驱动信号及芯片的损坏或不良),二、打印头的不良(断针/短针与磁轭线圈的损坏);三、打印头联接电缆线(开路与短路)。
首先,根据主板驱动芯片的损坏而导致的缺针来逐步推进,如右图所示可以看到:→逻辑主板门阵列控制芯片IC→输出24针信号到打印针大功率驱动电路→24针信号经过驱动电路放大以及消磁电路作相关控制→由PCB板线路搭接到两个插座上(如DS-1700打印机主板上的CN3与CN4)→再经两条软性联接电缆(打印头头缆)联接到打印头(打印头+38V电源在联接头缆插座CN3/CN4处接入)。
即:在主控逻辑电路板上引起缺针的关键部件,如门阵列芯片、各打印针驱动芯片模块(如TRA4、TRA5等)、消磁驱动模块(如TRA3、TRA6等)、及相关周边电路及线路的开路与短路。
再次,在打印头上引起缺针的主要部件:打印针的磨损/断针、打印头内部24组线圈绕组的短路/开路。
→打印针短针与断针,当出现短针与断针时可把打印头拆卸下来后,通过观察便可得知。
→打印头内部线圈磁轭组件开路或短路时,可通过使用万用表测量线圈阻值得知。
第三,打印头联接电缆不良,简称头缆不良;这一类不良的主要产生原因为头缆的插头因插拔的次数累计,头缆线头与主板插座的插拔磨擦使得软电缆线中金属导体脱离、至相邻间引脚短路或断裂而引起的开路与短路。
当开路时可表现为因驱动信号不能到达打印头线圈进行激励驱动而缺针,出现短路时,在自检“针号测试”中可表现为同一根针号出针两次(或不出针),而这样的短路会最终导致因线圈的阻抗小而烧毁;两针同时损坏、缺针。
打印头头缆不良时,最简单的方法就是通过肉眼观察是否存在破损、金属导体翘起及短路;也可通过使用万用表欧姆档测量其导通性。
2、故障排除划分打印头故障的排除可划分为:1)主板故障引起(更换主板)、2)打印头头缆不良引起(更换头缆)、3)打印头不良可划分为:①打印针不良, ②线圈磁轭不良。
柯美黑白机复印件跟原件对不齐调整步骤柯美彩机复印件跟原件对不齐调整步骤第一步:打一张测试页做原件及进维修模式方法1、2、4、进维修模式方法:停止健(STOP)0 0 停止健0 1这个就是停止健第二步:先对齐“打印区域”(调整这项,一般是在复印机做总清之后才做的,如果师傅没有说做这一项,请不要调该项)1、2、3、4、侧缘:这个方向线条空白跟对面的空白不相等,就调侧缘,直到测试页这些线侧缘方向左右两边的空白都差不多就好了(如上图左右方法)主缘:就是主缘方向(如上图上下方向),这些线条的上下空白相差很远,就调主缘,直到测试页这些线主缘方向上下两边的空白都差不多就好了纸张FD方向调整:就是主缘这个方向这些线条缩小较严重,就调该值,做总清后,一般这个值应调到0.8-1.0之间。
这种测试页如果这些线条不居中,也就是说线条在复印纸上四周的空白长度不相同,就应调以上三个值。
而且每个纸盒都需要调整,但是主缘的值应该所有的纸盒都应差不多。
第三步:再对好“扫描区域”(也就是在玻璃稿台上复印对齐问题)1、先分清“扫描区域”里的,主缘、侧端、FD方向、CD方向如上图所示,原件这样放在玻璃上主缘:原件放好在玻璃上的左边,那是复印件跟原件这个地方对不齐,就调这个值。
侧端:最上面那里原件和复印件有对不齐的,就调这个值。
CD方向调整(侧缘方向):就是原件跟复印件上下方向的扩大或缩小了,调该值。
FD方向调整(主缘方向):就是原件跟复印件左右方向的扩大或缩小了,调该值。
2、第四步:自动输稿对位调整1、2、进纸方向里面50% 100% 200%,每个选项的值都可调到一样,就是双面100%这个选项比其它的大0.2值就可以了。
3、如上图所示:前缘:就是左右方向,原件跟复印健前缘对不齐,就调这个值侧缘:就是上下方向,原件跟复印健侧缘对不齐,就调这个值进维修模式方法:进纸方向(前缘方向):就是上下方向的扩大或缩小,如原件跟复印件这个方向扩大或缩小了,就调这个值。
hp cp1025 彩色打印机- 闪烁的指示灯控制面板上的指示灯用于指示产品状态。
根据打印机的状态,这些指示灯可能会亮起、熄灭或闪烁。
这些指示灯能够以不同方式闪烁,反映打印机状态或潜在的错误情况。
note: 本文将打印机指示灯的指示方式描述为“闪烁”或“闪亮”。
在本文中,这两个词的意思完全相同。
figure 1: hp laserjet pro cp1025 和cp1025nw 控制面板指示灯和按钮1. 无线按钮和指示灯(仅限cp1025nw)2 - 5. 硒鼓按钮和指示灯6. “警示”指示灯7. “就绪”指示灯8. “恢复”按钮9. “取消”按钮闪烁的指示灯下面介绍了一些最常见的闪烁组合,并针对每种组合提供了相应的解决方法。
根据您的打印机上指示灯的闪烁情况,在下表中找到相应的指示灯闪烁方式,并按照说明排除故障。
note: 您或许可以通过多种方法解决某些指示灯闪烁的问题。
如果您找到了与您打印机当前的指示灯状态相同的闪烁方式,请尝试使用每种解决方法解决该问题。
问题:指示灯全部熄灭指示灯全部熄灭的解决方法指示灯全部熄灭。
打印机处于“自动开启/自动关闭”模式或处于关闭状态。
按电源按钮()停用“自动开启/自动关闭”模式或启动打印机。
问题:“警示”和“就绪”指示灯循环闪烁“警示”和“就绪”指示灯循环闪烁的解决方法接口初始化(开启)过程中或者产品执行清洁页过程中,状态指示灯循环闪烁。
无需执行任何操作。
等待初始化过程完成。
完成初始化过程后,打印机进入就绪状态。
问题:“就绪”指示灯亮起“就绪”指示灯亮起的解决方法打印机进入就绪状态。
无需执行任何操作。
打印机已准备好接收打印作业。
问题:“就绪”指示灯闪烁“就绪”指示灯闪烁的解决方法打印机正在接收或处理数据。
无需执行任何操作。
打印机正在接收或处理打印作业。
问题:“警示”指示灯闪烁,“就绪”指示灯亮起“警示”指示灯闪烁,“就绪”指示灯亮起的解决方法打印机处于手动送纸模式,或者打印机正在等待打印双面打印机作业的另一面。
理光1075、2075常见问题及解决方法:理光复印机进入维修模式是:黄键+107+红键不动(三秒以上)。
当显示屏有变化的时候,我们也能看到屏幕上会出现sp模式。
理光sc541.sc542. sc543。
sc545。
sc546. sc547. sc548等开关机不能消除的代码,可以使用上面的操作消除。
(理光35张以下的机器锁机的消除方法就不一样了.)进入维修模式我们看以下,sp3001代码显示,如果不是255数字,硒鼓基本工作正常,如果接近255,有两种情况,硒鼓老化和传感器脏了,sp2801-002如果这个数字,很小说明定影器里面载体老化或者是太脏。
脏的话我可以拿细筛子筛除里面的异物。
重新做sp2801—001 自动检测一次。
Sp2001是充电高压(电压越高复印效果越差,颜色浅),sp2201是显影偏压(电压越低复印效果越差,颜色浅)复印机复印颜色浅,造成这种情况有很多,载体老化,硒鼓老化,碳粉质量(大部分待用粉通病:颜色过浅颜色过深,定影卡纸.)扫描玻璃脏,激光器脏,如何判断什么情况引起的颜色变浅呢?如果有打印卡的话,打印一张,再复印一张就能判断出是不是扫描玻璃引起的颜色浅了。
激光器造成复印颜色浅,一般观察复印件就能判断,如果是均匀的颜色浅,一般就不是激光器造成的。
如果复印件表面有低灰,多数因为硒鼓老化,或者载体老化引起的.碳粉质量引起的话,就比较不好判断了。
更换一个别用的非常好的,测试一下,测试之前,最好清理一下硒鼓,转印,显影器.现在着重说一下。
理光1075和2090等高速机器的问题吧。
Sc550 清洁纸使用完毕,更换清洁纸需要将sp1902-001 改为0 按# 确认一下,sc300一般是因为硒鼓充电架脏了,我们一颗螺丝取下来,用脱脂棉酒精。
进行清理。
如果定影器经常卡纸,加上你使用的是待用粉的话我推荐大家。
将清洁纸的速度调快一点(一般10-15). 理光1075理光2075复印机故障代码541怎么处理 1.热敏电阻温度侦测错应该是跳543 544,跳541等于是灯管没加热,可能是白色温度保险丝跳电,可能的话将180P或185P保险丝改成190p至195p耐温系数,或是将保险丝卸下检查受热面是否陷落,直接将跳电的保险丝跳线,或是摔击地面让其弹起。
HP2550彩色激光打印机拆解三接口板Post By:2005-4-20 13:20:18
HP2550系列彩色激光打印机在市场上占有率颇高,为方便各位会员进一步清晰了解此系列打印机的各部分结构及拆卸方法,上海普广数码科技有限公司特意购置一台HP Laser jet2550L打印机供业内人士观摩,参考!本系列拆解共分六辑. 第一辑,介绍搓纸轮分页器的拆解更换
第二辑,介绍定影组件的拆解
第三辑,介绍接口板的拆解
第四辑,介绍激光器的拆解
第五辑,介绍电源板的拆解
第六辑,机器其它部分配件观摩,HP2500/1500/2550系列彩色激光打印机原厂维修手册
以上六辑将分期登出,请各位会员关注!
此主题相关图片如下:
此主题相关图片如下:
此主题相关图片如下:
此主题相关图片如下:
此主题相关图片如下:
此主题相关图片如下:
此主题相关图片如下:
此主题相关图片如下:
此主题相关图片如下:
此主题相关图片如下:
此主题相关图片如下:
此主题相关图片如下:
此主题相关图片如下:
此主题相关图片如下:
此主题相关图片如下:
此主题相关图片如下:。
HP CP1025/M175拆装机(对位)注意事项
故障现象:CP1025,M175拆装事项,请特别注意红色字体内容。
适用机型:CP1025/M175
解决方案:
CP1025和M175打印平台是一样,区别在于M175多一个扫描平台。
这里以M175为例说明。
一)拆扫描头注意事项
二)拆装加热组件注意事项
三)安装ITB注意事项
四)机器发出异响注意事项
一)拆扫描组件注意事项
1.注意拆卸着力点的部位: 1)机器底部;2)侧盖几个着力点。
参考下图:
3. 两边分离开盖合页后,双手把扫描组件拿开。
二)拆加热组件注意事项
1.下面拆打印部分,和CP1025基本相同。
在拆打印部分的过程中,不管是拆CP1025还是M175,打印机一定先要完全关机,确保加热组件的压力滚轴归位后,才能拆机。
如果压力滚轴没有归位,就拆机,以后回装加热组件时,会有安装问题。
2.如何判断加热组件的压力滚轴归位?
查看加热组件中间第二个孔中,是否有一白色突起?如果有,说明压力滚轴归位了。
如果没有,则没有归位。
4.当安装加热组件时, 确保加热组件释压驱动凸轮(红圈所标)保持下图所示位置。
即凸轮手柄处于最低端。
三)拆装ITB注意事项
安装的ITB备件分两种来源:1)从机器上拆下来的ITB备件;2)从SRFR系统申请到的ITB备件。
1. 从机器上拆下来的ITB备件安装注意事项:
回装ITB时,需注意ITB左边(从后面看)有个白色齿轮。
白色齿轮缺口应与侧面的一个小黑三角标记对齐,然后回装ITB。
红圈为白色齿轮缺口和小黑三角对应好的位置,如下图:
2)安装SRFR到货新ITB注意事项:
a.新到货ITB需要释放TIB弹簧。
可以用一字螺丝刀,把两边画圈的地方向内顶开,这时ITB会自动把皮带拉紧,如下图:
b.安装新的ITB皮带时,注意左侧白色齿轮缺口应与小黑三角标记对应。
如果此白色齿轮和小黑三角没有对好,装上去后会发出咔咔声响。
c.新到的ITB备件有个桔红色的卡子,可以不用取出。
把ITB完全装入机器中,方可取出,如下图。
四)机器发出异响问题注意事项
1.首先排查机器是否有过灌装耗材或非HP原装耗材,可以更换新碳粉盒来测试,需一次更换四个碳粉盒。
更换后看是否解决异响问题,如果解决,可以再用原来碳粉盒一个个去测试,查看是其中哪一个碳粉盒的问题。
2.如果更换碳粉盒无效,需检查机器右侧一处齿轮组,是否发出咔咔响声,我们可以开机时,用手按住右上盖中间部位。
感应是否有轻微震动声,如下图所示:
3.如果有震动,折下右侧盖,揭开上图红圈所标塑料护盖。
可以看到下图的这块转动齿轮,仔细观察可以发现齿轮在咬合处,有一齿轮不同,如下图:
4.在机器上面齿轮,有一组齿轮是两个齿牙联在一起和别的齿轮牙不一样。
拆下来的齿轮组,有个齿轮和别的齿轮略短一些。
重点就在于,一定要让拆下来略短齿轮和机器上面并联齿轮咬合一致。
如果安装的过程中,发现不好很好掌握对齐,我们可以把机器左边带动碳粉盒转轴马达拆下,再来安装,这样就比较容易安装。
知识改变命运。