当前位置：文档之家 › 53203中文资料

53203中文资料

  • 格式：pdf
  • 大小：96.32 KB
  • 文档页数：4

53200 SPDT SOLID-STATE RELAYS 5320353204Mii MICROCIRCUITS PRODUCTSDIVISIONFeatures:• Replacements for M31-1, M31-1A, M31-2 A• SPDT, Break-Before-Make• Up to 1500 V RMS Optical Isolation• Output current up to 8.2 Amps (53203)• Power FET Output Low On-state Resistance • Full Military Temperature Operation: -55ºC to +125ºC• Military Environmental Screening Available Applications:• Heater Load Switching • Sensor Activation• Remote Signal Activation • Servo and synchro control • High power switchingDESCRIPTIONThe MII 53200, 53203, and 53204 are military SPDT high power, solid-state relays. These light-weight devices are resistant to damage from shock and vibration, and are immune to contact-related problems (contamination, arcing) associated with mechanical equivalents. Optical coupling between the input and output stages provides effective isolation up to 1500 volts AC RMS. Power FET outputs eliminate bipolar offset, and minimize output voltage drop for high current capability. The control logic is CMOS compatible, and will accommodate bias supplies between 4 and 16 VDC. A TTL input driver with pull-up resistor may also be used. These solid-state relays are ideal for use in military systems, or wherever high reliability, low power actuation, and light-weight are design considerations. Applications include general-purpose signal switching and electronic load control.ABSOLUTE MAXIMUM RATINGSIsolation Voltage1.................................................................................................................................................1000 VAC RMS Continuous Operating Output Voltage3: 53200...............................................................................................................80 VDC53203..............................................................................................................80 VDC53204............................................................................................................160 VDC Load Current2: 53200...........................................................................................................................................4.8 Amps DC 53203 ..........................................................................................................................................8.2 Amps DC53204...........................................................................................................................................5.2 Amps DC Bias Supply Voltage, V DD .................................................................................................................................................16 VDC Control Logic Input Voltage..............................................................................................................................................16 VDC Operating Temperature ...........................................................................................................................-55ºC to +125ºC Case Storage Temperature .........................................................................................................................................-55ºC to +125ºC Notes: 1 60 Hz sine wave 2 at 25ºC with 2.0º C/W heat sink 3 Reversing polarity on the output may cause permanent damage.Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement.ELECTRICAL CHARACTERISTICST A = +25° CPARAMETER CONDITIONSMINTYPMAXUNIT Isolation Voltage, I/O 60 Hz Sine Wave 1500 VAC RMSIsolation Resistance Input to Case, at 50V 109Ohms Continuos Operating Output Voltage53200 53203 532048080160VDCVDCVDCTransient Output Voltage53200 53203 532048080180VDCVDCVDCLoad Current: 532005320353204 2.0 ºC/W Heat Sink 4.88.25.2Amps DCAmps DCAmps DCOn Resistance: 5320053203532040.3 0.150.38OhmsOhmsOhmsCapacitance, I/O 25 V, 1 MHz 5 PFLeakage Current: 532005320353204 Load Voltage =Maximum204040µAµAµABias Supply Voltage, V DD 4 16VDC Bias Current 13 16 MAControl Logic Voltage 16 VDCControl Logic Current 2 µAControl Logic Level – High 0.75VDDVDCControl Logic Level – Low 0 0.15 V DD VDCt r (Rise Time): 53200 53203 53204 Load Voltage = 25 VDCR L = 50Ω2.03.03.0msmsmst on (Turn-On-Time): 53200 5320353204 3.04.04.0msmsmst f (Fall Time) 50 µst off (Turn-Off-Time): 53200 5320353204 200 250250µsµsµst d (Dwell Time) 0.5 1.5 ms Thermal Resistance, θJA:53200 5320353204 232020ºC/WºC/WºC/WThermal Resistance, θJC:53200 5320353204 7.04.24.2ºC/WºC/WºC/WMicropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement.Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement.Truth TableINPUT (PIN 1)PIN 12 PIN 16High Closed OpenLow Open Closed1COMMONFET OUTPUTV DD CONTROL LOGICGNDINPUT BUFFERMicropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement..735(.060)(1.390).240 MAX.1.000.600.800.200TOL: ±.010(BOTTOM VIEW).200.4002216311291.4501.7502.100.45 MIN.Ø.1572 PLACESØ.040, 6 PLACES.795。

合集下载

AD5320中文资料

AD5320中文资料

元器件交易网
a
+2.7 V to +5.5 V, 140 ␮A, Rail-to-Rail Output 12-Bit DAC in a SOT-23 AD5320*
FUNCTIONAL BLOCK DIAGRAM
VDD GND POWER-ON RESET
FEATURES Single 12-Bit DAC 6-Lead SOT-23 and 8-Lead ␮SOIC Packages Micropower Operation: 140 ␮A @ 5 V Power-Down to 200 nA @ 5 V, 50 nA @ 3 V +2.7 V to +5.5 V Power Supply Guaranteed Monotonic by Design Reference Derived from Power Supply Power-On-Reset to Zero Volts Three Power-Down Functions Low Power Serial Interface with Schmitt-Triggered Inputs On-Chip Output Buffer Amplifier, Rail-to-Rail Operation SYNC Interrupt Facility APPLICATIONS Portable Battery Powered Instruments Digital Gain and Offset Adjustment Programmable Voltage and Current Sources Programmable Attenuators
VDD 10
1/4 Scale to 3/4 Scale Change (400 Hex to C00 Hex). RL = 2 kΩ; 0 pF < CL < 200 pF. See Figure 16. RL = 2 kΩ; CL = 500 pF RL = ∞ RL = 2 k Ω 1 LSB Change Around Major Carry. See Figure 19.
53253中文资料

53253中文资料

Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement.Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible.PRELIMINARY DATA SHEET53253 RADIATION TOLERANT, 90V - 0.8ADUAL POWER MOSFET OPTOCOUPLERSMiiHYBRID MICROELECTRONICSPRODUCTS DIVISIONFeatures:• Designed for 100 krad(Si) Total Dose • 8-Pin Dual-In-Line Hermetic Package • Performance over –55°C to +125°C • Compact Isolation Solid State Switches • Continuous Output Current: 0.8 A (1)• Optically Coupled between Input and Output • Isolation Tested to 1000 VDC • High Level of Transient Immunity • 3 A Output Surge Current• Shock and Vibration Resistant•MIL-PRF-38534 screening optionalA pplications:• Satellite/Spacesystems • Military/High Reliability Systems• Standard 28 VDC and 48 VDC Load Driver• AircraftControls • Electromechanical and Solid State RelayReplacement• I/OModules • SwitchingHeaters DESCRIPTIONThe 53253 is two power MOSFET optocouplers in a single 8-pin dual-in-line package suitable for applications wheretwo independent switches and radiation tolerant performance are required. The popular hermetic eight-pin dual-in-line ceramic package combined with 1000 VDC isolation between input and output and between two isolated relays,makes this device ideal for solid-state relay applications. Performance is specified over the full military temperature range. This device is available as COTS, or screened to MIL-PRF-38534, Table C-IX, Class H or custom screening.Lead options support both through-hole and surface-mount assembly. Gold plated leads are standard, but other lead finishes per MIL-PRF-38534 are also available.Functionally, the device operates as two SPST, normally open (2 Form A) solid-state relays. Each relay is actuated by an input current, which can be driven from a standard TTL device. The input current biases a light emitting diode that is optically coupled to an integrated photovoltaic diode array. The photovoltaic diode array energizes control circuitry that operates the output MOSFET.Preliminary Data Sheet53253 Radiation Tolerant Dual Power MOSFET Optocouplers ABSOLUTE MAXIMUM RATINGS:(Per relay unless otherwise noted)Storage Temperature Range ..………………………………………………………….........………........... -65°C to +150°C Operating Ambient Temperature - T A ...................……………………………………………….…....….. -55°C to +125°C Junction Temperature - T J ..............................……………………………………………………...…..….........…. +150°C Lead Solder Temperature for 10 seconds .......................………………………………………....…...….............. +260°C (1.6 mm below seating plane) Average Input Current - I F ....................…...……………………………………………………….......................... 20 mA Peak Repetitive Input Current - I Fpk .............……………………………………...…………..………...................... 40 mA(pulse width < 100 ms; duty cycle < 50%) Peak Surge Input Current - I Fpk surge .............…………………………………..……………………................... 100 mA(pulse width < 0.2 ms; duty cycle < 0.1%) Continuous Output Current per relay - I O ...…………………………………....………..............................…....... 0.8 A (1) Single Shot Output Current per relay- I Opk surge (pulse width < 10 ms) ………..……………..…...………………...... 3 A Output Voltage - V O ............................…...………………………………………….……………….…….............. 90 VDC RECOMMENDED OPERATING CONDITIONS:Parameter Symbol Min.Max.UnitsInput Current (ON)I F (ON)520mAInput Voltage (OFF)V F (OFF)00.6VDCOperating Temperature T A-55+125°CMicropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement.Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible.Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement.Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible.Preliminary Data Sheet 53253Radiation Tolerant Dual Power MOSFET Optocouplers ELECTRICAL SPECIFICATIONS (Pre-Irradiation)T A = -55°C to +125°C, unless otherwise specified.A F (ON) F (OFF)Notes:1.Maximum average current rating where the case temperature (T C ) is maintained below 120°C.2.During the pulsed R ON measurement (I O duration < 30 ms), ambient (T A ) and case temperature (T C ) are equal.3.This is a momentary withstand test, not a continuous operating condition.4.Typical junction to case thermal resistance (θJC ) for the device is 15°C/W, where case temperature (T C ) is measured at the center of the package bottom.CAUTION:Care should be taken not to exceed the maximum output power dissipation, maximum case temperature, and maximum junction temperature when repetitively switching loads.元器件交易网Micropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement.Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible.Preliminary Data Sheet53253Radiation Tolerant Dual Power MOSFET Optocouplers元器件交易网元器件交易网Preliminary Data Sheet53253Radiation Tolerant Dual Power MOSFET OptocouplersMicropac Industries cannot assume any responsibility for any circuits shown or represent that they are free from patent infringement.Micropac reserves the right to make changes at any time in order to improve design and to supply the best product possible.。

耐中性盐雾性能的测试中文

耐中性盐雾性能的测试中文

van Laar-划痕雕刻 Clemen-划痕雕刻对于第二段引用的国际标准所对应的德国标准如下：ISO 1512 见 DIN EN ISO 15528ISO 1513 见 DIN EN ISO 1513ISO 1514 见DIN EN ISO 1514ISO 2808 见DIN ISO 2808ISO 3270 见 DIN ISO 23270ISO 3574 见 DIN 1623-1ISO 3696 见 DIN ISO 3696ISO 4628-1 见 DIN 53230，E DIN ISO 4823-1大众集团 按照DIN说明进行复制ISO 4628-2 见DIN 53209，E DIN ISO 4823-2ISO 4628-3 见DIN 53210，E DIN ISO 4823-3ISO 4628-4 见DIN ISO 4628-4，E DIN ISO 4823-4ISO 4628-4 见DIN ISO 4628-5，E DIN ISO 4823-5修改相对于DIN 53167:1985-12对如下内容进行了修改：等效采用国际标准ISO 7253:1996的规定。

无本质性的变动，因为以前的版本标准DIN 53167：1985-12对测试的描述在内容上与国际标准ISO 7253一致。

ISO 4628-8应采纳DIN 53176：1985-12对样板评价的描述，并计划作为欧洲标准（DIN EN ISO 4628-8）采用。

以前的版本DIN 53167：1972-08，1985-12国家的附录（NA）(资料性附录)国家之间的附录的文献指示DIN 53209，涂层气泡度的标志DIN 53210，涂层或类似的涂覆层的生锈标志DIN 53230，涂料和类似的涂覆层材料的检验——检验的分析结果鉴定系统DIN EN 10130 用于冷变型的低碳钢冷轧板——交货技术条件DIN EN 23270，清漆和色漆以及它们的材料——预处理和试验用的温度和湿度（ISO 3270:1984）；德语版本EN 23270：1991DIN EN ISO 1513，清漆和色漆——用于进一步测试的取样的预测试和准备（ISO 1513:1992）；德语版本EN ISO 1513：1994。

LEICA Q3相机使用说明书

LEICA Q3相机使用说明书

镜头
• 直射阳光从正前方照到相机时，镜头会发挥犹如聚焦镜的效力。因此，必须保护相机免受强光照射。装上镜头盖、并将相 机置于阴凉处（或最好放进袋子里），有助于避免相机内部损坏。
电池
• 新电池必须在首次使用前充电，以便能在相机中使用。建议给电池充满电，因为电池在交付时只充了部分电。 • 电池使用不当或使用非指定型号的电池都可能引起爆炸！ • 请勿将电池长时间暴露于阳光下、高温、潮湿或有冷凝水的环境中。也不得将电池放在微波炉或高压容器中，否则有引起
19 方向按钮 在菜单中： – 在菜单中导航 – 套用菜单设置 在拍摄模式下： – 移动自动对焦测距区
20 中间按钮 在菜单中： – 套用菜单设置 在拍摄模式下： – 直接访问菜单功能 – 出厂设置：切换配置文件信息 在回放模式下： – 出厂设置：切换配置文件信息
21 扬声器 22 电池仓 23 电池解锁滑块 24 三脚架螺口
（5180-5320 MHz）
接入点+客户端模式：
IEEE802.11a/n/ac: 149–165频道 (5745–5825 MHz)
日本
接入点+客户端模式： 客户端模式： （仅适用于室内） （仅适用于室内）
IEEE802.11a/n/ac: IEEE802.11a/n/ac: 52–144
36–48频道
安全须知
一般性
• 请勿在有强力磁场、静电或电磁场的装置（例如电磁炉、微波炉、电视或计算机显示器、视频游戏机、手机、收音机）的附近 使用您的相机。其电磁场可能会干扰影像记录。
• 强磁场，例如扬声器或大型电动机，可能会损坏储存的数据或影响拍摄。 • 如果相机因受到电磁场影响而出现故障，请您关闭相机，取出电池，稍后重新开启相机。 • 请按照下列要求保存好小部件，例如配件靴座盖：