工程机械英语词汇大全

建筑学常用英语词汇：-frame A型骨架A-truss A型构架abrasion 磨耗；磨蚀abrasive cut-off machine 磨切机abrasive grinding machine 磨机(火石机) abrasive particle 磨粒absorption 吸收abutment 桥台；拱座abutting end 邻接端acceleration 加速acceleration lane 加速车道acceleration pedal 加速器踏板accelerator 催凝剂；加速器；催化剂acceptance criteria 接受准则access 通路；通道access door 检修门；通道门access lane 进出路径access panel 检修门access point 入口处；出入通道处access ramp 入口坡道；斜通道access road 通路；通道access shaft 竖井通道access spiral loop 螺旋式回旋通道access staircase 通道楼梯access step 上落踏板；出入踏板access tunnel 隧道通道accessible roof 可到达的屋顶；有通道的屋顶accessory 附件；配件accident 事故；意外accidental collapse 意外坍塌accommodate 装设；容纳accredited private laboratory 认可私营实验室accumulator 储压器；蓄电池accuracy limit 准确度极限acetylene cylinder 乙炔气(风煤)樽acid plant 酸洗设备；酸洗机acid pump 酸液泵acid tank 酸液缸acoustic couplant 声耦合剂acoustic coupler 声耦合器acoustic lining 隔音板acoustic screen 隔声屏acrylic paint 丙烯漆料acrylic sheet 丙烯胶片(阿加力胶片)active corrosion 活性腐蚀active earth pressure 主动土压力active oxidation 活性氧化actual plot ratio 实际地积比率actuator 促动器；唧筒；激发器adapt 改装adaptor 适配器；适配接头(万能苏)；转接器；接合器addition 增设；加建additional building works 增补建筑工程additional horizontal force 额外横向力additional plan 增补图则additional vent 加设通风口additive 添加剂adhesive 黏结剂；胶黏剂adhesive force 附力adit 入口；通路；坑道口adjacent construction 相邻建造物adjacent level 相邻水平adjacent site 相邻地盘adjacent street 相邻街道adjoining area 毗邻地区adjoining building 毗邻建筑物adjoining land 毗邻土地adjoining structure 毗邻构筑物adjustable 可调校adjuster 调节器adjustment 调校；调整admixture 掺合剂；外加剂advance directional sign 前置指路标志；方向预告标志advance earthworks 前期土方工程advance warning sign 前置警告标志advance works 前期工程aeration 灌气aeration tank 曝气池aerial 天线aerial rapid transit system 架空快速运输系统aerial ropeway 架空缆车系统aerial view 鸟瞰图aerofoil 翼型aerosol 悬浮微粒；喷雾affix 贴附aftercooler 后冷却器afterfilter 后过滤器agent 作用剂；代理人aggregate 骨料；集料；碎石aggregate area 总面积aggregate grading 骨料级配aggregate superficial area 表面总面积aggregate usable floor space 总实用楼面空间agitator 搅拌器；搅动机air bleeding 放气air blower 鼓风机air brake 气压制动器air circuit 空气回路air circuit breaker 空气断路器air cleaner 空气滤清器air compressor 空气压缩机air compressor governor 空气压缩机调压器air conditioning 空气调节air cooled chiller 风冷式冷冻机air cooler 空气冷却器air cooling system 空气冷却系统；风冷系统air coupling valve 空气联接阀air curtain fan 风帘风扇air cylinder 气缸；气筒air damper 风闸；气流调节器air distribution system 配气系统air distributor 空气分配器air dryer 空气干燥器air duct 通风管道；气槽air entrained cement 加气水泥；伴水泥air entraining agent 加气剂air exhaust 排气口air filter 空气滤器；风隔；隔尘网air filter chamber 空气过滤室air flowmeter 风量计；空气流量计air gap 气隙air grill 空气格栅air inlet 进风口；进气孔air inlet louver 进气百叶air inlet port 进气口air intake 进风口；进气孔；入气口air intake duct 进风槽air intake filter 进气过滤器air isolating cock 空气隔断旋塞air line breathing apparatus 气喉型呼吸器具air line strainer 进气管道隔滤器air outlet 出风口air outlet grille 空气出口栅格air particle 空气粒子air passage 风道air pipe/pipework 通气管；送气管air piston 空气活塞air pressure gauge 气压表air pressure switch 气压掣air pressurization system 空气加压系统air receiver 空气储存器air reservoir 储气缸air restrictor 空气节流器air shuttle valve 阻气阀air sprayer 喷涂器air spring 空气弹簧air strainer 空气隔滤器；空气滤网air supply outlet 供气出口air supply valve 供气阀air tank 空气箱air valve 进出气阀；放气阀air valve pit 进出气阀井；放气阀井air vent cock 通风管旋塞air ventilator 空气通风器air-operated damper 气动风闸airshaft 通风竖井airtight cover 气密盖airy dry varnish 风干清漆alarm 警报；警报器alarm bell 警钟alarm buzzer 警报器alga 水藻align 对准；调直；定线alignment (road) 路线；线向(特指道路中线的位置与方向) alignment plan (road) 路线平面图alkali-silica reaction 碱矽反应alkaline aggregate reaction 碱性集料反应alkaline pump 碱液泵alkaline tank 碱液缸alkalinity 碱度all-purpose road 混合车道；综合车道alley 巷allowable load 容许载重；容许荷载allowable stress 容许应力alloy 合金alloy steel bar 合金钢筋条alluvial deposit 冲积土层；冲积物alteration 更改；改建；改动alternating current (a.c.) 交流电alternative design 替代设计alternative route 替代路线alternator 交流发电机aluminium tape 铝带amber flashing light 黄色闪灯ambient pressure 周围压力ambient temperature 环境温度；周围温度amendment 修订amenities 市容建筑；设施；康乐设施amenity area 美化市容地带amenity railing 美观栏杆ammeter 电流表；安培计ampere (A) 安培(电流量单位) amplification 放大；增强amplitude 幅；振幅anchor 锚；锚竿支撑anchor bearing 锚承；锚座anchor bolt 锚栓anchor plate 锚碇板anchorage 锚碇；碇泊区；抛锚区；锚固anchorage length 锚固长度anchoring strength 锚固强度ancillary building 附属建筑物ancillary facilities 附属设施ancillary installation 附带装置ancillary works 附属工程angle cutter 角铁切割机angle iron bracket 角铁支架；角铁托架angle probe 斜探头angular velocity 角速度annunciation lamp 警示灯annunciator 传播器；呼唤器anode 阳极anode voltage 阳极电压antenna 天线anti-corrosion paint 防蚀漆anti-creep device 防溜装置anti-lift roller 防升滚轮anti-oxidizing paint 抗氧化漆anti-rust paint 防锈漆anti-skid chequer 防滑格纹anti-skid device 防滑装置anti-skid dressing 防滑钢沙anti-skid material 防滑物料anti-slip 防滑动；防空转；防打滑anti-static chain 抗静电链anti-static tyre 抗静电轮胎anti-stripping agent 防剥剂anti-syphonage pipe 反虹吸管anti-tip roller 防倾侧滚轮anti-vibration mounting 防震装置anti-vibration pad 防震垫anvil 铁砧aperture 隙缝；孔口apex 顶尖apparatus 仪器；装置；器具；器材appliance 用具；装置；设备applied covering 外加覆盖物applied load 外施荷载approach 进路；引道；接驳道路；引桥approach channel 进港航道；引渠approach ramp 引道坡approach road 引道；进路approach speed 来车速度approach taper 楔形引道路段approach viaduct 高架引道approved material 经批准的物料approved plan 经批准的图则appurtenance 附属物apron 跳板；护板；停机坪arc 电弧arc contact 电弧触点arc runner 电弧滚环arc welding 电弧焊接arch 拱；弓形；拱门architect 建筑师；则师architectural decoration 建筑装饰architectural projection 建筑上的伸出物area traffic control system 区域交通控制系统argon arc welding 氩气焊armature 电枢arrangement 排列；布置arresting assembly 止动装置arterial highway 干线道路arterial traffic 干线交通article of agreement 合约细则artificial lighting 人工照明as-built drawing 竣工图则as-constructed drawing 竣工图则asbestos abatement works 石棉拆除工程asbestos cement 石棉水泥asbestos gasket 石棉垫片ash pit 排渣槽；灰坑asphalt 沥青asphalt distributor 沥青喷洒机asphalt paver 沥青摊铺机asphalt roofing 沥青屋面asphaltic coating 沥青涂层asphaltic concrete 沥青混凝土aspirator 吸气器assemblage 组合物assembly 装置；组合assessment 评估associated works 相关工程；相关设施at-grade pedestrian crossing 地面行人过路处at-grade signal controlled junction 交通灯控制地面路口atmospheric distillation 常压蒸馏atmospheric pressure 大气压力；常压atmospheric temperature 常温atomization air fan 雾化空气风扇attachment 附件；附属物attenuation 衰减audible signal 音响讯号audible warning 音响警号authorities 权限authority 主管当局authorized officer 获授权人员authorized person 获授权人；认可人士；核准人士authorized works 获授权进行的工程；批准进行的工程automatic (spark) ignition device 自动(火花)点火装置automatic control switch 自动控制开关automatic operation 自动操作automatic release 自动脱扣automatic voltage regulator 自动调压器automatic weather station 自动气象站automation equipment 自动化设备auxiliary control panel 辅助掣板auxiliary equipment 辅助设备auxiliary feedwater pump 辅助给水泵auxiliary feedwater tank 辅助给水箱auxiliary plant 辅助厂房auxiliary system 辅助系统auxiliary water pump 辅助水泵average compressive stress 平均压应力average strength 平均强度axial fan 轴流式风扇axial force 轴向力axial load 轴向载重；轴向荷载axial stress 轴向应力axle bearing 车轴轴承(车轴啤令)A- frame A型骨架A-truss A型构架abrasion 磨耗；磨蚀abrasive cut-off machine 磨切机abrasive grinding machine 磨机(火石机) abrasive particle 磨粒absorption 吸收abutment 桥台；拱座abutting end 邻接端acceleration 加速acceleration lane 加速车道acceleration pedal 加速器踏板accelerator 催凝剂；加速器；催化剂acceptance criteria 接受准则access 通路；通道access door 检修门；通道门access lane 进出路径access panel 检修门access point 入口处；出入通道处access ramp 入口坡道；斜通道access road 通路；通道access shaft 竖井通道access spiral loop 螺旋式回旋通道access staircase 通道楼梯access step 上落踏板；出入踏板access tunnel 隧道通道accessible roof 可到达的屋顶；有通道的屋顶accessory 附件；配件accident 事故；意外accidental collapse 意外坍塌accommodate 装设；容纳accredited private laboratory 认可私营实验室accumulator 储压器；蓄电池accuracy limit 准确度极限acetylene cylinder 乙炔气(风煤)樽acid plant 酸洗设备；酸洗机acid pump 酸液泵acid tank 酸液缸acoustic couplant 声耦合剂acoustic coupler 声耦合器acoustic lining 隔音板acoustic screen 隔声屏acrylic paint 丙烯漆料acrylic sheet 丙烯胶片(阿加力胶片)active corrosion 活性腐蚀active earth pressure 主动土压力active oxidation 活性氧化actual plot ratio 实际地积比率actuator 促动器；唧筒；激发器adapt 改装adaptor 适配器；适配接头(万能苏)；转接器；接合器addition 增设；加建additional building works 增补建筑工程additional horizontal force 额外横向力additional plan 增补图则additional vent 加设通风口additive 添加剂adhesive 黏结剂；胶黏剂adhesive force 附力adit 入口；通路；坑道口adjacent construction 相邻建造物adjacent level 相邻水平adjacent site 相邻地盘adjacent street 相邻街道adjoining area 毗邻地区adjoining building 毗邻建筑物adjoining land 毗邻土地adjoining structure 毗邻构筑物adjustable 可调校adjuster 调节器adjustment 调校；调整admixture 掺合剂；外加剂advance directional sign 前置指路标志；方向预告标志advance earthworks 前期土方工程advance warning sign 前置警告标志advance works 前期工程aeration 灌气aeration tank 曝气池aerial 天线aerial rapid transit system 架空快速运输系统aerial ropeway 架空缆车系统aerial view 鸟瞰图aerofoil 翼型aerosol 悬浮微粒；喷雾affix 贴附aftercooler 后冷却器afterfilter 后过滤器agent 作用剂；代理人aggregate 骨料；集料；碎石aggregate area 总面积aggregate grading 骨料级配aggregate superficial area 表面总面积aggregate usable floor space 总实用楼面空间agitator 搅拌器；搅动机air bleeding 放气air blower 鼓风机air brake 气压制动器air circuit 空气回路air circuit breaker 空气断路器air cleaner 空气滤清器air compressor 空气压缩机air compressor governor 空气压缩机调压器air conditioning 空气调节air cooled chiller 风冷式冷冻机air cooler 空气冷却器air cooling system 空气冷却系统；风冷系统air coupling valve 空气联接阀air curtain fan 风帘风扇air cylinder 气缸；气筒air damper 风闸；气流调节器air distribution system 配气系统air distributor 空气分配器air dryer 空气干燥器air duct 通风管道；气槽air entrained cement 加气水泥；伴水泥air entraining agent 加气剂air exhaust 排气口air filter 空气滤器；风隔；隔尘网air filter chamber 空气过滤室air flowmeter 风量计；空气流量计air gap 气隙air grill 空气格栅air inlet 进风口；进气孔air inlet louver 进气百叶air inlet port 进气口air intake 进风口；进气孔；入气口air intake duct 进风槽air intake filter 进气过滤器air isolating cock 空气隔断旋塞air line breathing apparatus 气喉型呼吸器具air line strainer 进气管道隔滤器air outlet 出风口air outlet grille 空气出口栅格air particle 空气粒子air passage 风道air pipe/pipework 通气管；送气管air piston 空气活塞air pressure gauge 气压表air pressure switch 气压掣air pressurization system 空气加压系统air receiver 空气储存器air reservoir 储气缸air restrictor 空气节流器air shuttle valve 阻气阀air sprayer 喷涂器air spring 空气弹簧air strainer 空气隔滤器；空气滤网air supply outlet 供气出口air supply valve 供气阀air tank 空气箱air valve 进出气阀；放气阀air valve pit 进出气阀井；放气阀井air vent cock 通风管旋塞air ventilator 空气通风器air-operated damper 气动风闸airshaft 通风竖井airtight cover 气密盖airy dry varnish 风干清漆alarm 警报；警报器alarm bell 警钟alarm buzzer 警报器alga 水藻align 对准；调直；定线alignment (road) 路线；线向(特指道路中线的位置与方向) alignment plan (road) 路线平面图alkali-silica reaction 碱矽反应alkaline aggregate reaction 碱性集料反应alkaline pump 碱液泵alkaline tank 碱液缸alkalinity 碱度all-purpose road 混合车道；综合车道alley 巷allowable load 容许载重；容许荷载allowable stress 容许应力alloy 合金alloy steel bar 合金钢筋条alluvial deposit 冲积土层；冲积物alteration 更改；改建；改动alternating current (a.c.) 交流电alternative design 替代设计alternative route 替代路线alternator 交流发电机aluminium tape 铝带amber flashing light 黄色闪灯ambient pressure 周围压力ambient temperature 环境温度；周围温度amendment 修订amenities 市容建筑；设施；康乐设施amenity area 美化市容地带amenity railing 美观栏杆ammeter 电流表；安培计ampere (A) 安培(电流量单位)amplification 放大；增强amplitude 幅；振幅anchor 锚；锚竿支撑anchor bearing 锚承；锚座anchor bolt 锚栓anchor plate 锚碇板anchorage 锚碇；碇泊区；抛锚区；锚固anchorage length 锚固长度anchoring strength 锚固强度ancillary building 附属建筑物ancillary facilities 附属设施ancillary installation 附带装置ancillary works 附属工程angle cutter 角铁切割机angle iron bracket 角铁支架；角铁托架angle probe 斜探头angular velocity 角速度annunciation lamp 警示灯annunciator 传播器；呼唤器anode 阳极anode voltage 阳极电压antenna 天线anti-corrosion paint 防蚀漆anti-creep device 防溜装置anti-lift roller 防升滚轮anti-oxidizing paint 抗氧化漆anti-rust paint 防锈漆anti-skid chequer 防滑格纹anti-skid device 防滑装置anti-skid dressing 防滑钢沙anti-skid material 防滑物料anti-slip 防滑动；防空转；防打滑anti-static chain 抗静电链anti-static tyre 抗静电轮胎anti-stripping agent 防剥剂anti-syphonage pipe 反虹吸管anti-tip roller 防倾侧滚轮anti-vibration mounting 防震装置anti-vibration pad 防震垫anvil 铁砧aperture 隙缝；孔口apex 顶尖apparatus 仪器；装置；器具；器材appliance 用具；装置；设备applied covering 外加覆盖物applied load 外施荷载approach 进路；引道；接驳道路；引桥approach channel 进港航道；引渠approach ramp 引道坡approach road 引道；进路approach speed 来车速度approach taper 楔形引道路段approach viaduct 高架引道approved material 经批准的物料approved plan 经批准的图则appurtenance 附属物apron 跳板；护板；停机坪arc 电弧arc contact 电弧触点arc runner 电弧滚环arc welding 电弧焊接arch 拱；弓形；拱门architect 建筑师；则师architectural decoration 建筑装饰architectural projection 建筑上的伸出物area traffic control system 区域交通控制系统argon arc welding 氩气焊armature 电枢arrangement 排列；布置arresting assembly 止动装置arterial highway 干线道路arterial traffic 干线交通article of agreement 合约细则artificial lighting 人工照明as-built drawing 竣工图则as-constructed drawing 竣工图则asbestos abatement works 石棉拆除工程asbestos cement 石棉水泥asbestos gasket 石棉垫片ash pit 排渣槽；灰坑asphalt 沥青asphalt distributor 沥青喷洒机asphalt paver 沥青摊铺机asphalt roofing 沥青屋面asphaltic coating 沥青涂层asphaltic concrete 沥青混凝土aspirator 吸气器assemblage 组合物assembly 装置；组合assessment 评估associated works 相关工程；相关设施at-grade pedestrian crossing 地面行人过路处at-grade signal controlled junction 交通灯控制地面路口atmospheric distillation 常压蒸馏atmospheric pressure 大气压力；常压atmospheric temperature 常温atomization air fan 雾化空气风扇attachment 附件；附属物attenuation 衰减audible signal 音响讯号audible warning 音响警号authorities 权限authority 主管当局authorized officer 获授权人员authorized person 获授权人；认可人士；核准人士authorized works 获授权进行的工程；批准进行的工程automatic (spark) ignition device 自动(火花)点火装置automatic control switch 自动控制开关automatic operation 自动操作automatic release 自动脱扣automatic voltage regulator 自动调压器automatic weather station 自动气象站automation equipment 自动化设备auxiliary control panel 辅助掣板auxiliary equipment 辅助设备auxiliary feedwater pump 辅助给水泵auxiliary feedwater tank 辅助给水箱auxiliary plant 辅助厂房auxiliary system 辅助系统auxiliary water pump 辅助水泵average compressive stress 平均压应力average strength 平均强度axial fan 轴流式风扇axial force 轴向力axial load 轴向载重；轴向荷载axial stress 轴向应力axle bearing 车轴轴承(车轴啤令)back-fire 逆火back-up area 后勤地区；辅助埸地backfill 回填；回填土backfill material 回填物料background noise 本底噪声；背景噪声backing plate 垫板；背板baffle 隔板；挡板baffle plate 遮挡板baffle wall 遮挡墙balance tank 调节池；均衡槽balance weight 平衡锤balanced load 平衡载重balancer 平冲器balancing pipeline 平衡水管balcony 露台ball bearing 滚珠轴承ball valve 浮球阀；球形阀；波阀ball-and-socket joint 球窝接头ballast 道碴bamboo scaffolding 竹枝棚架band brake 带式制动器band clamp 带夹banshee alarm 尖啸警报bar 铁枝；杆；巴(压力量单位)bar tendon 钢筋barging area 驳运地点barrack 营房barrel 管筒；芯管barrette 方形桩barricade 路障；障碍物barrier 栏栅；护栏；障碍物；屏障barrier block 路障barrier gate 路闸barrier plate 阻挡板base 基座base course 路面下层；承重层；路基层base frame 基架base insulator 基架绝缘器base plate 底板；垫板base sealing 底部密封胶base slab 平底板base support 底座支架baseline 基线；底线；基准线baseline programme 基线计划basement 地库；地窖；地下室batching plant 混凝土混和机；配料厂batter pile 斜桩battery 蓄电池battery acid level 电池酸位battery cell volt 蓄电池电压battery charger 电池充电器battery electric locomotive 电力机车battery electrolyte 电池电解液battery-powered device 电池推动装置beacon 闪光指示灯bead 焊珠beam 横梁bearing 支座；支承；承座；轴承(啤令)；方向角bearing capacity 承载力bearing force 承重能力；承载能力bearing pad 支承垫片；承重垫片bearing pile 支承桩bearing pin 支承栓钉bearing plate 支承垫板bearing stress 支承应力bearing surface 支承面bedding 底层；层理bedplate 座板bedrock 基层岩behaviour 性能；状况Belisha beacon 斑马线灯；黄波灯bellow pot 气囊；气囊筒belt 带；皮带belt conveyor 带式输送机belt guard 皮带护罩belt tension 皮带拉力bend 弯角；弯位；路弯；弯管bending force 弯曲力bending stress 弯曲应力Benkelman beam test 贝克曼梁试验bentonite 膨润土；膨土岩berm channel 斜水平台渠berth 停泊处；碇泊位bevel 斜角；斜面bias 偏移bill of quantities 工料清单binder 黏合料bit 钻头bitumen 沥青bitumen coating 沥青外搪层；沥青外衬bitumen felt 沥青纸bitumen lining 沥青内搪层；沥青衬里bituminous concrete 沥青混凝土bituminous macadam 沥青碎石bituminous waterproof membrane 沥青防水膜blade 剪刀；叶片blank flange 盲板法兰；盲板凸缘；管口盖板blanking plate 封板blast-furnace 鼓风炉blast-furnace slag cement 炉渣水泥blasting 爆石；爆破bleed nipple 放气嘴；减压嘴bleed off pipe 溢流管bleed screw 放气螺钉；减压螺钉bleeding 泌浆(混凝土)；泌水性(混凝土) blended cement 混合水泥blending control 混合控制blinding 补路石砂；(填充表面孔隙的细石)block plan 楼宇平面图blow down 放水；放气blow down valve 放泄阀；排水阀blower 吹风机；鼓风机bobbin 绕线管bogie 转向架boiler room 锅炉房boiling point 沸点bollard 护柱；系船柱bollard light 安全岛指示灯bollard plinth 护柱柱基；护柱基座bolster 承枕；横撑bolt 螺栓bond 黏结；黏合；契约bond coat 黏合层bond strength 黏合强度bond stress 黏合应力boom 吊杆booster pump 增压泵booster pumping station 增压抽水站booster transformer 增压变压器booster water pump 增压水泵；增压抽水机borated water storage tank 含硼水贮存箱border link 边境连接道路border terminus 过境终站bore 钻孔；内孔bored pile 螺旋钻孔桩bored tunnel 钻挖的隧道borehole log 钻孔纪录boric acid 硼酸boring 钻探；冲孔boring machine 钻探机；镗床borrow area 采泥区；采料区bottleneck 樽颈；狭窄段bottom heave 底部隆bottom layer 底层bottom plate 底板boulder 巨砾boundary 分界线；界线box culvert 盒形排水渠；盒形暗渠；箱形暗渠；方形去水渠box girder 箱形大梁brace 撑杆；支撑braced structure 受横向支撑的结构bracing 支撑bracing structure 支撑结构bracket 托架；支架braid 编织电缆brake 制动器brake horse power 制动马力brake lining 制动器摩擦衬片brake pedal 刹车踏脚板brake system 制动系统brake test 制动器试验brake tester 制动系统测试器braking distance 制动距离；刹车距离branch circuit 分支电路branch pipe/pipework 支管；分支喉管brass gate valve 黄铜闸阀brass wire brush 铜丝刷break pressure tank 减压配水缸箱；水压调节池breaker 轧碎机；碎石机；隔断器；开关闸；断路器；保险掣breaking strength 抗断强度breakthrough 击穿breakwater 防波堤breather 通气孔；呼吸器breather valve 通气阀breathing apparatus 呼吸器具brick 砖brick works 砌砖工程brickwork 砖块bridge 桥梁bridge abutment 桥台bridge crane 桥式吊机bridge deck 桥面板；桥板；桥面bridge girder 桥大梁bridge pier 桥墩bridgeworks 桥梁工程bubble accumulator 气泡贮存器bucket conveyor 斗式输送机buckling 压曲；压弯buckling load 压曲临界荷载buffer 缓冲；缓冲器；减震器buffer area 缓冲地区build, operate and transfer (BOT) franchise 「建造、营运及移交」专营权builder's lift 施工用升降机building 楼宇；建筑物；大厦building area 建筑面积building condition 楼宇状况building construction 建筑物建造；建筑营造building design 建筑物设计；建筑设计building envelope 建筑物外壳building frontage 屋宇前面building land 屋地；屋宇建筑用地building material 建筑物料building plan 建筑图则building services 屋宇设备；屋宇装building site 屋宇建筑地盘；工地building works 屋宇建筑工程；楼宇建筑工程bulk excavation works 大型挖掘工程bulldozer 推土机；铲泥车bump (road) 限速路面突块bumper 缓冲器；防撞器；防撞杠bunch 捆扎bund ；田基；堤bund wall 墙bunded area 堤保护区buoyant force 浮力burglar alarm system 防盗警钟系统buried concrete 埋入地下的混凝土burner 燃烧器；炉头bursting 爆裂bus interchange 巴士转车处bus stop shelter 巴士站上盖bus terminus 巴士总站bus-bar 导电条；母线(巴士巴)bus-coupler 母线联接bush 轴衬(杯士)butt fusion welding 对头熔接butt welding 对焊butterfly cock 蝶形旋阀butterfly gate 蝶形闸butterfly valve 蝶形阀buttress 支墩buzzer 蜂音器；蜂鸣器by-pass 绕道；支路；支管；旁通管by-pass valve 旁通阀cab 小室；驾驶室cabinet 小室；贮存柜cable 电缆cable channel 电缆沟；电缆槽cable conduit 电缆管cable coupler 电缆耦合器cable draw pit 电缆沙井；铺缆井cable duct 电缆管道cable gland 电缆密封套cable joint 电缆接头cable laying wagon 电缆敷设车cable lead 电缆引线cable route 电缆路线cable supported viaduct 悬索高架桥cable suspension bridge 钢索吊桥cable trench 电缆槽cable trough 电缆坑cable trunk 电缆干线cable tunnel 电缆隧道cable-stayed bridge 斜拉桥cage 机厢caisson 沉箱caisson cap 沉箱盖caisson foundation 沉箱地基；沉箱基础caisson pier 沉箱墩caisson pile 沉箱桩caisson retaining wall 沉箱挡土墙caisson wall 沉箱墙calibration 校准caliper measure 测径calorie (cal) 卡路里(热量单位)calorific value 热值calorifier 加热器cam 突轮camber 拱度candela (cd) 烛光(发光强度单位) canister respirator 罐型防毒面具canopy 檐篷cantilever 悬臂cantilever beam 悬臂梁cantilever bridge 悬臂桥cantilever crane 悬臂吊机cantilever footing 悬臂基脚cantilever foundation 悬臂地基cantilever support 悬臂支架canvas 帆布canvas belt 帆布带cap 帽；盖capacitance meter 电容表capacitor 电容器capacity 容量；载客量capacity control valve 容量控制阀capital works 基本建设工程；基建工程；carbon brush 碳刷carbon pile 碳柱carbon ring 碳环carbon steel 含碳钢carbon strip 碳条carbonation 碳化carbonation depth 碳化深度carbonation process 碳化过程carborundum 金刚砂carburettor 化油器；气化器cargo handling area 货物装卸区carriageway 行车道carriageway marking 行车道标记carrying capacity 运载量；载重量；承载能力cartridge 子弹；弹药筒cartridge operated tool 弹药推动的工具cartridge type respirator 滤罐型呼吸器；筒型防毒面具（猪咀）casing 套管cast iron 铸铁；生铁cast iron conductor 铸铁导管cast iron pipe 铸铁管(生铁管)cast-in anchorage 浇注锚固cast-in-place 灌注；现场浇筑cast-in-situ concrete unit 现场浇筑混凝土构件casting basin 预制件工场casualty team 伤亡急救队cat ladder 便梯；爬梯catalytic action 催化作用catch 挡片；制止器；扣掣；门扣catch fan 扇形防护网架catch fence 拦截围墙catch platform 坠台catchment area 集水区；引集范围catchpit 排水井；集水坑；截流井catchwater channel 集水槽catenary wire 吊索cathode 阴极cathode ray tube 阴极射线管cathodic protection 阴极保护catwalk 跳板；轻便梯；轻便栈桥caulk 堵缝caulking material 填隙料causeway 堤道caution sign 警告标志cavern 洞穴cavity 中空部分；穴cavity wall 空心墙ceiling 天花板ceiling slab 天花板ceiling suspension hook 天花吊cell 电池cellular office 分格式办公室cement 水泥cement content 水泥含量cement mortar 水泥沙浆cement plaster 水泥灰泥cement rendering 水泥荡面cement sand mix 水泥沙浆cementitious content 水泥质成分centi (c) 厘(百分之一)central divider 中央分隔栏central dividing strip 中央分隔带central line 中线central median 中央分隔带central power-driven machine 中央动力机械central profile barrier 中央纵向护栏central reserve 中央预留带central span 中跨距centre lane 中行车线centre line 中心线centre line of street 街道中心线centrifugal filter 离心过滤器centrifugal force 离心力centrifugal load 离心荷载centrifugal pump 离心泵centripetal force 向心力ceramic tile 瓷砖certificate 证明书certificate of inspection 检查证明书certificate of registration 注册证明书；登记证明书certification 核证certified copy 经核证文本certify 核证cesspool 污水池chain 链chain block 滑车吊链；链动滑轮(尖箔落) chainage 丈量长度；里程距离chainlink fence 扣环围栏；铁网围栏chamber 小室；间隔chamfer 去角(斜角)位；斜削change-over switch 转换开关change-over valve 转换阀channel 沟渠；线糟；槽；渠道；频道channel cover 槽盖channelization (traffic) (交通)导流channelizing island 导行岛channelizing line 导行线characteristic strength 特征强度chart datum 海图基准面chart recorder 图表记录器chasis 车身底盘check 查核check block 挡块check joint 止回接头check mechanism 制动装置check plate 垫板；挡板check rail 护轮轨check screw 止动螺钉check valve 止回流阀chemical action 化学作用chemical dosing 化学剂量chemical grout 化学灌浆chemical property 化学特性chemical refuse 化学垃圾chemical test 化学测试chemicals 化学品chequered plate 网纹板chill plate 冷却板chilled air fan 冷风风扇chilled water pump 冷冻水泵chiller 冷冻机chiller plant 致冷设备；制冷设备chimney 烟沟；烟chimney coping 烟囱盖顶chimney stack 烟囱chippings 碎屑；破片chisel 凿chloride 氯化物chloride content 氯化物含量chloride diffusion 氯化物扩散chloride extraction 除氯chloride ion 氯离子chloride ion content 氯离子含量chlorinated polyvinyl chloride (PVC-C) 氯化聚氯乙烯chlorinated water 加有氯气的水chlorinator 加氯器chopper 斩波器chunam 灰泥土批荡chute 溜槽；滑道chute 槽管circuit 电路；环道circuit breaker 断路保险掣circular footing 圆基脚circular road 环回道路circulating water pump 循环水泵circulation mode 循环模式circumferential road 环回道路civil works 土木工程cladding 骨架外墙；覆盖层claim 声称；申索；索偿clamp 夹钳claplock cable clamp 拍扣式电缆线夹clay 黏土clay field pipe 瓦管cleaning eye 清理孔cleaning rod 清理棒cleansing 洁净clear effective length 净有效长度clear height 净高clear opening 净开口clear space 净空间clear span 净跨距clear width 净阔度clearance 相距空间；清折行动clearance gauge 测隙规clearance space 间隙空间cleat 夹具clevis U形夹client 委托人climb form technique 提升模板技术climbing lane 爬坡车道clip 小夹close fitting cover 紧合封盖close fittings 紧合配件close-boarded platform 密合封板平台closed area 禁区closed circuit television (CCTV) 闭路电视closed end 不能通行的一端closed position 闭合的位置closure 封闭cloverleaf interchange 四叶式交汇处；蝶式交汇处clutch 离合器co-ordinator 统筹人coal-tar epoxy 环氧煤焦油coarse aggregate 粗集料；粗骨料coarse screening 粗筛coating 保护层；涂层coating material 涂盖物质cock 旋塞；旋阀code of practice 工作守则；操作守则code reader 读码器coefficient 系数coefficient of expansion 膨胀系数coefficient of linear expansion 线性膨胀系数cofferdam 围堰坝cohesive force 黏合力；凝聚力coil 线圈；簧圈；盘管cold milling 刨去路面旧沥青cold reduced steel wire 冷轧钢丝cold solvent welding 冷冻溶剂焊接cold storage 冷藏库collapse 坍塌collapsible cantilever platform 可摺悬臂平台collapsible gate 摺闸collar 护圈；束套；套环collet 套爪；筒夹colluvial deposit 崩积土层colour code 色码colour light signal 颜色灯号coloured cement 颜色水泥column 柱column cap 柱帽column footing 柱基脚column frame 柱架column head 柱头combined dead load 组合恒载combined effect 混合效应combined footing 联合基脚combined load 合并载重combustible goods 可燃物品combustible material 可燃烧物料combustion 燃烧combustion chamber 燃烧室commencement of operation 开始操作commercial building 商业建筑物commercial complex 商场commercial land 商业用地commercial use 商业用途commissioning 启用；投产；投入服务；开始使用；开始运作commitment 承担common corridor 公用走廊common part 公用部分common use 共同使用common waste pipe 共用废水管communal facilities 公用设施communication channel/link 通讯渠道communication system 通讯系统commutator 整流器commuter 交通工具的经常乘客compacted concrete 压实混凝土compaction 压实；夯实compaction pile 压实桩compaction test 压实测试compartment 分隔室；隔室compartment wall 分隔墙compatibility 相配；相容compensating valve 补偿阀compensation 补偿；补偿金competent person 合资格人士；有资格人士complement 补充设备complete function test 全面功能试验complete fusion 完全熔接complete overhaul 全面大修completed works 已完成的工程compliance 遵从composite beam 组合梁composite building 综合用途建筑物composite pile 混合桩composite sandwich construction 复合夹层结构composite steel plate 复合钢板composite wall 组合墙composition 成分compound 场地；合成物comprehensive details 全面细节；整体细节comprehensive development area 综合发展区comprehensive redevelopment area 综合重建区comprehensive transport interchange facilities 综合交通交汇设施comprehensive transport study 整体运输研究compressed air 压缩空气compressed air tunnelling method 压缩空气开挖隧道法compressed gas 压缩气体compressing tool 压挤工具compression 压缩compression joint 承压接缝compression load 压缩荷载compression reinforcement 受压钢筋compression test 抗压测试compressive failure 压缩塌毁；压缩毁坏compressive strength 抗压强度compressive stress 抗压应力compressor 压缩机computer aided design (CAD) facilities 电脑辅助设计设施computer graphics 电脑绘图computerized automatic concrete cube crushing machine 电脑化混凝土立方块压力试验机concave 凹形concealed piping 隐藏喉管concentrated load 集中载重；集中荷载concept plan 概念图则conceptual layout 概念规划concrete 混凝土；三合土；石屎concrete barrier 混凝土防撞栏concrete block 混凝土趸concrete block seawall 混凝土海堤concrete buffer 混凝土缓冲concrete core 混凝土芯concrete cover 混凝土保护层concrete cube 混凝土立方块concrete cube test 混凝土立方体试验concrete durability 混凝土耐用程度concrete foundation 混凝土基础concrete grade 混凝土等级concrete lining 混凝土搪层；混凝土衬里。

陶瓷ceramics合成纤维synthetic fibre电化学腐蚀electrochemical corrosion 车架automotive chassis悬架suspension转向器redirector变速器speed changer板料冲压sheet metal parts孔加工spot facing machining车间workshop工程技术人员engineer气动夹紧pneuma lock数学模型mathematical model画法几何descriptive geometry机械制图Mechanical drawing投影projection视图view剖视图profile chart标准件standard component零件图part drawing装配图assembly drawing尺寸标注size marking技术要求technical requirements刚度rigidity内力internal force位移displacement截面section疲劳极限fatigue limit断裂fracture塑性变形plastic distortion脆性材料brittleness material刚度准则rigidity criterion垫圈washer垫片spacer直齿圆柱齿轮straight toothed spur gear 斜齿圆柱齿轮helical-spur gear直齿锥齿轮straight bevel gear运动简图kinematic sketch齿轮齿条pinion and rack蜗杆蜗轮worm and worm gear虚约束passive constraint曲柄crank摇杆racker凸轮cams共轭曲线conjugate curve范成法generation method定义域definitional domain值域range导数\\微分differential coefficient求导derivation定积分definite integral不定积分indefinite integral曲率curvature偏微分partial differential毛坯rough游标卡尺slide caliper千分尺micrometer calipers攻丝tap二阶行列式second order determinant逆矩阵inverse matrix线性方程组linear equations概率probability随机变量random variable排列组合permutation and combination气体状态方程equation of state of gas动能kinetic energy势能potential energy机械能守恒conservation of mechanical energy 动量momentum桁架truss轴线axes余子式cofactor逻辑电路logic circuit触发器flip-flop脉冲波形pulse shape数模digital analogy液压传动机构fluid drive mechanism机械零件mechanical parts淬火冷却quench淬火hardening回火tempering调质hardening and tempering磨粒abrasive grain结合剂bonding agent砂轮grinding wheel后角clearance angle龙门刨削planing主轴spindle主轴箱headstock卡盘chuck加工中心machining center车刀lathe tool车床lathe钻削镗削bore车削turning磨床grinder基准benchmark钳工locksmith锻forge压模stamping焊weld拉床broaching machine拉孔broaching装配assembling铸造found流体动力学fluid dynamics流体力学fluid mechanics加工machining液压hydraulic pressure切线tangent机电一体化mechanotronics mechanical-electrical integration 气压air pressure pneumatic pressure稳定性stability介质medium液压驱动泵fluid clutch液压泵hydraulic pump阀门valve失效invalidation强度intensity载荷load应力stress安全系数safty factor可靠性reliability螺纹thread螺旋helix键spline销pin滚动轴承rolling bearing滑动轴承sliding bearing弹簧spring制动器arrester brake十字结联轴节crosshead联轴器coupling链chain皮带strap精加工finish machining粗加工rough machining变速箱体gearbox casing腐蚀rust氧化oxidation磨损wear耐用度durability随机信号random signal离散信号discrete signal超声传感器ultrasonic sensor集成电路integrate circuit挡板orifice plate残余应力residual stress套筒sleeve扭力torsion冷加工cold machining电动机electromotor汽缸cylinder过盈配合interference fit热加工hotwork摄像头CCD camera倒角rounding chamfer优化设计optimal design工业造型设计industrial moulding design有限元finite element滚齿hobbing插齿gear shaping伺服电机actuating motor铣床milling machine钻床drill machine镗床boring machine步进电机stepper motor丝杠screw rod导轨lead rail组件subassembly可编程序逻辑控制器Programmable Logic Controller PLC 电火花加工electric spark machining电火花线切割加工electrical discharge wire - cutting相图phase diagram热处理heat treatment固态相变solid state phase changes有色金属nonferrous metal陶瓷ceramics合成纤维synthetic fibre电化学腐蚀electrochemical corrosion车架automotive chassis悬架suspension转向器redirector变速器speed changer板料冲压sheet metal parts孔加工spot facing machining车间workshop工程技术人员engineer气动夹紧pneuma lock数学模型mathematical model画法几何descriptive geometry机械制图Mechanical drawing投影projection视图view剖视图profile chart标准件standard component零件图part drawing装配图assembly drawing尺寸标注size marking技术要求technical requirements刚度rigidity内力internal force位移displacement截面section疲劳极限fatigue limit断裂fracture塑性变形plastic distortion脆性材料brittleness material刚度准则rigidity criterion垫圈washer垫片spacer直齿圆柱齿轮straight toothed spur gear 斜齿圆柱齿轮helical-spur gear直齿锥齿轮straight bevel gear运动简图kinematic sketch齿轮齿条pinion and rack蜗杆蜗轮worm and worm gear虚约束passive constraint曲柄crank摇杆racker凸轮cams共轭曲线conjugate curve范成法generation method定义域definitional domain值域range导数\\微分differential coefficient求导derivation定积分definite integral不定积分indefinite integral曲率curvature偏微分partial differential毛坯rough游标卡尺slide caliper千分尺micrometer calipers攻丝tap二阶行列式second order determinant逆矩阵inverse matrix线性方程组linear equations概率probability随机变量random variable排列组合permutation and combination气体状态方程equation of state of gas动能kinetic energy势能potential energy机械能守恒conservation of mechanical energy 动量momentum桁架truss轴线axes余子式cofactor逻辑电路logic circuit触发器flip-flop脉冲波形pulse shape数模digital analogy液压传动机构fluid drive mechanism机械零件mechanical parts淬火冷却quench淬火hardening回火tempering调质hardening and tempering磨粒abrasive grain结合剂bonding agent砂轮grinding wheelAssembly line 组装线Layout 布置图Conveyer 流水线物料板Rivet table 拉钉机Rivet gun 拉钉枪Screw driver 起子Pneumatic screw driver 气动起子worktable 工作桌OOBA 开箱检查fit together 组装在一起fasten 锁紧(螺丝)fixture 夹具(治具)pallet 栈板barcode 条码barcode scanner 条码扫描器fuse together 熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME 制造工程师MT 制造生技cosmetic inspect 外观检查inner parts inspect 内部检查thumb screw 大头螺丝lbs. inch 镑、英寸EMI gasket 导电条front plate 前板rear plate 后板chassis 基座bezel panel 面板power button 电源按键reset button 重置键Hi-pot test of SPS 高源高压测试Voltage switch of SPS 电源电压接拉键sheet metal parts 冲件plastic parts 塑胶件SOP 制造作业程序material check list 物料检查表work cell 工作间trolley 台车carton 纸箱sub-line 支线left fork 叉车personnel resource department 人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer |plein|刨床miller铣床grinder磨床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vice section superisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |\\'skr?pid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |\\' ksi\\'dei?n|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单location地点present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheet PCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet 库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked 待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet 年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕??shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机阿基米德蜗杆Archimedes worm安全系数safety factor; factor of safety安全载荷safe load凹面、凹度concavity扳手wrench板簧flat leaf spring半圆键woodruff key变形deformation摆杆oscillating bar摆动从动件oscillating follower摆动从动件凸轮机构cam with oscillating follower 摆动导杆机构oscillating guide-bar mechanism 摆线齿轮cycloidal gear摆线齿形cycloidal tooth profile摆线运动规律cycloidal motion摆线针轮cycloidal-pin wheel包角angle of contact保持架cage背对背安装back-to-back arrangement背锥back cone ；normal cone背锥角back angle背锥距back cone distance比例尺scale比热容specific heat capacity闭式链closed kinematic chain闭链机构closed chain mechanism臂部arm变频器frequency converters变频调速frequency control of motor speed变速speed change变速齿轮change gear change wheel变位齿轮modified gear变位系数modification coefficient标准齿轮standard gear标准直齿轮standard spur gear表面质量系数superficial mass factor表面传热系数surface coefficient of heat transfer表面粗糙度surface roughness并联式组合combination in parallel并联机构parallel mechanism并联组合机构parallel combined mechanism并行工程concurrent engineering并行设计concurred design, CD不平衡相位phase angle of unbalance不平衡imbalance (or unbalance)不平衡量amount of unbalance不完全齿轮机构intermittent gearing波发生器wave generator波数number of waves补偿compensation参数化设计parameterization design, PD残余应力residual stress操纵及控制装置operation control device槽轮Geneva wheel槽轮机构Geneva mechanism ；Maltese cross槽数Geneva numerate槽凸轮groove cam侧隙backlash差动轮系differential gear train差动螺旋机构differential screw mechanism差速器differential常用机构conventional mechanism; mechanism in common use 车床lathe承载量系数bearing capacity factor承载能力bearing capacity成对安装paired mounting尺寸系列dimension series齿槽tooth space齿槽宽spacewidth齿侧间隙backlash齿顶高addendum齿顶圆addendum circle齿根高dedendum齿根圆dedendum circle齿厚tooth thickness齿距circular pitch齿宽face width齿廓tooth profile齿廓曲线tooth curve齿轮gear齿轮变速箱speed-changing gear boxes齿轮齿条机构pinion and rack齿轮插刀pinion cutter; pinion-shaped shaper cutter 齿轮滚刀hob ,hobbing cutter齿轮机构gear齿轮轮坯blank齿轮传动系pinion unit齿轮联轴器gear coupling齿条传动rack gear齿数tooth number齿数比gear ratio齿条rack齿条插刀rack cutter; rack-shaped shaper cutter齿形链、无声链silent chain齿形系数form factor齿式棘轮机构tooth ratchet mechanism插齿机gear shaper重合点coincident points重合度contact ratio冲床punch传动比transmission ratio, speed ratio传动装置gearing; transmission gear传动系统driven system传动角transmission angle传动轴transmission shaft串联式组合combination in series串联式组合机构series combined mechanism串级调速cascade speed control创新innovation creation创新设计creation design垂直载荷、法向载荷normal load唇形橡胶密封lip rubber seal磁流体轴承magnetic fluid bearing从动带轮driven pulley从动件driven link, follower从动件平底宽度width of flat-face从动件停歇follower dwell从动件运动规律follower motion从动轮driven gear粗线bold line粗牙螺纹coarse thread大齿轮gear wheel打包机packer打滑slipping带传动belt driving带轮belt pulley带式制动器band brake单列轴承single row bearing单向推力轴承single-direction thrust bearing单万向联轴节single universal joint单位矢量unit vector当量齿轮equivalent spur gear; virtual gear当量齿数equivalent teeth number; virtual number of teeth当量摩擦系数equivalent coefficient of friction当量载荷equivalent load刀具cutter导数derivative倒角chamfer导热性conduction of heat导程lead导程角lead angle等加等减速运动规律parabolic motion; constant acceleration and deceleration motion等速运动规律uniform motion; constant velocity motion等径凸轮conjugate yoke radial cam等宽凸轮constant-breadth cam等效构件equivalent link等效力equivalent force等效力矩equivalent moment of force等效量equivalent等效质量equivalent mass等效转动惯量equivalent moment of inertia等效动力学模型dynamically equivalent model底座chassis低副lower pair点划线chain dotted line（疲劳）点蚀pitting垫圈gasket垫片密封gasket seal碟形弹簧belleville spring顶隙bottom clearance定轴轮系ordinary gear train; gear train with fixed axes动力学dynamics动密封kinematical seal动能dynamic energy动力粘度dynamic viscosity动力润滑dynamic lubrication动平衡dynamic balance动平衡机dynamic balancing machine动态特性dynamic characteristics动态分析设计dynamic analysis design动压力dynamic reaction动载荷dynamic load端面transverse plane端面参数transverse parameters端面齿距transverse circular pitch端面齿廓transverse tooth profile端面重合度transverse contact ratio端面模数transverse module端面压力角transverse pressure angle锻造forge对称循环应力symmetry circulating stress对心滚子从动件radial (or in-line ) roller follower对心直动从动件radial (or in-line ) translating follower对心移动从动件radial reciprocating follower对心曲柄滑块机构in-line slider-crank (or crank-slider) mechanism 多列轴承multi-row bearing多楔带poly V-belt多项式运动规律polynomial motion多质量转子rotor with several masses惰轮idle gear额定寿命rating life额定载荷load ratingII 级杆组dyad发生线generating line发生面generating plane法面normal plane法面参数normal parameters法面齿距normal circular pitch法面模数normal module法面压力角normal pressure angle法向齿距normal pitch法向齿廓normal tooth profile法向直廓蜗杆straight sided normal worm法向力normal force反馈式组合feedback combining反向运动学inverse ( or backward) kinematics反转法kinematic inversion反正切Arctan范成法generating cutting仿形法form cutting方案设计、概念设计concept design, CD防振装置shockproof device飞轮flywheel飞轮矩moment of flywheel非标准齿轮nonstandard gear非接触式密封non-contact seal非周期性速度波动aperiodic speed fluctuation非圆齿轮non-circular gear粉末合金powder metallurgy分度线reference line; standard pitch line分度圆reference circle; standard (cutting) pitch circle 分度圆柱导程角lead angle at reference cylinder分度圆柱螺旋角helix angle at reference cylinder分母denominator分子numerator分度圆锥reference cone; standard pitch cone分析法analytical method封闭差动轮系planetary differential复合铰链compound hinge复合式组合compound combining复合轮系compound (or combined) gear train复合平带compound flat belt复合应力combined stress复式螺旋机构Compound screw mechanism复杂机构complex mechanism杆组Assur group干涉interference刚度系数stiffness coefficient刚轮rigid circular spline钢丝软轴wire soft shaft刚体导引机构body guidance mechanism刚性冲击rigid impulse (shock)刚性转子rigid rotor刚性轴承rigid bearing刚性联轴器rigid coupling高度系列height series高速带high speed belt高副higher pair格拉晓夫定理Grashoff`s law根切undercutting公称直径nominal diameter高度系列height series功work工况系数application factor工艺设计technological design工作循环图working cycle diagram工作机构operation mechanism工作载荷external loads工作空间working space工作应力working stress工作阻力effective resistance工作阻力矩effective resistance moment公法线common normal line公共约束general constraint公制齿轮metric gears功率power功能分析设计function analyses design共轭齿廓conjugate profiles共轭凸轮conjugate cam构件link鼓风机blower固定构件fixed link; frame固体润滑剂solid lubricant关节型操作器jointed manipulator惯性力inertia force惯性力矩moment of inertia ,shaking moment 惯性力平衡balance of shaking force惯性力完全平衡full balance of shaking force惯性力部分平衡partial balance of shaking force 惯性主矩resultant moment of inertia惯性主失resultant vector of inertia冠轮crown gear广义机构generation mechanism广义坐标generalized coordinate轨迹生成path generation轨迹发生器path generator滚刀hob滚道raceway滚动体rolling element滚动轴承rolling bearing滚动轴承代号rolling bearing identification code 滚针needle roller滚针轴承needle roller bearing滚子roller滚子轴承roller bearing滚子半径radius of roller滚子从动件roller follower滚子链roller chain滚子链联轴器double roller chain coupling滚珠丝杆ball screw滚柱式单向超越离合器roller clutch过度切割undercutting函数发生器function generator函数生成function generation含油轴承oil bearing耗油量oil consumption耗油量系数oil consumption factor赫兹公式H. Hertz equation合成弯矩resultant bending moment合力resultant force合力矩resultant moment of force黑箱black box横坐标abscissa互换性齿轮interchangeable gears花键spline滑键、导键feather key滑动轴承sliding bearing滑动率sliding ratio滑块slider环面蜗杆toroid helicoids worm环形弹簧annular spring缓冲装置shocks; shock-absorber灰铸铁grey cast iron回程return回转体平衡balance of rotors混合轮系compound gear train积分integrate机电一体化系统设计mechanical-electrical integration system design 机构mechanism机构分析analysis of mechanism机构平衡balance of mechanism机构学mechanism机构运动设计kinematic design of mechanism机构运动简图kinematic sketch of mechanism机构综合synthesis of mechanism机构组成constitution of mechanism机架frame, fixed link机架变换kinematic inversion机器machine机器人robot机器人操作器manipulator机器人学robotics技术过程technique process技术经济评价technical and economic evaluation技术系统technique system机械machinery机械创新设计mechanical creation design, MCD机械系统设计mechanical system design, MSD机械动力分析dynamic analysis of machinery机械动力设计dynamic design of machinery机械动力学dynamics of machinery机械的现代设计modern machine design机械系统mechanical system机械利益mechanical advantage机械平衡balance of machinery机械手manipulator机械设计machine design; mechanical design机械特性mechanical behavior机械调速mechanical speed governors机械效率mechanical efficiency机械原理theory of machines and mechanisms机械运转不均匀系数coefficient of speed fluctuation机械无级变速mechanical stepless speed changes基础机构fundamental mechanism基本额定寿命basic rating life基于实例设计case-based design,CBD基圆base circle基圆半径radius of base circle基圆齿距base pitch基圆压力角pressure angle of base circle基圆柱base cylinder基圆锥base cone急回机构quick-return mechanism急回特性quick-return characteristics急回系数advance-to return-time ratio急回运动quick-return motion棘轮ratchet棘轮机构ratchet mechanism棘爪pawl极限位置extreme (or limiting) position极位夹角crank angle between extreme (or limiting) positions计算机辅助设计computer aided design, CAD计算机辅助制造computer aided manufacturing, CAM计算机集成制造系统computer integrated manufacturing system, CIMS 计算力矩factored moment; calculation moment计算弯矩calculated bending moment加权系数weighting efficient加速度acceleration加速度分析acceleration analysis加速度曲线acceleration diagram尖点pointing; cusp尖底从动件knife-edge follower间隙backlash间歇运动机构intermittent motion mechanism 减速比reduction ratio减速齿轮、减速装置reduction gear减速器speed reducer减摩性anti-friction quality渐开螺旋面involute helicoid渐开线involute渐开线齿廓involute profile渐开线齿轮involute gear渐开线发生线generating line of involute渐开线方程involute equation渐开线函数involute function渐开线蜗杆involute worm渐开线压力角pressure angle of involute渐开线花键involute spline简谐运动simple harmonic motion键key键槽keyway交变应力repeated stress交变载荷repeated fluctuating load交叉带传动cross-belt drive交错轴斜齿轮crossed helical gears胶合scoring角加速度angular acceleration角速度angular velocity角速比angular velocity ratio角接触球轴承angular contact ball bearing角接触推力轴承angular contact thrust bearing 角接触向心轴承angular contact radial bearing 角接触轴承angular contact bearing铰链、枢纽hinge校正平面correcting plane接触应力contact stress接触式密封contact seal阶梯轴multi-diameter shaft结构structure结构设计structural design截面section节点pitch point节距circular pitch; pitch of teeth节线pitch line节圆pitch circle节圆齿厚thickness on pitch circle节圆直径pitch diameter节圆锥pitch cone节圆锥角pitch cone angle解析设计analytical design紧边tight-side紧固件fastener径节diametral pitch径向radial direction径向当量动载荷dynamic equivalent radial load径向当量静载荷static equivalent radial load径向基本额定动载荷basic dynamic radial load rating 径向基本额定静载荷basic static radial load tating径向接触轴承radial contact bearing径向平面radial plane径向游隙radial internal clearance径向载荷radial load径向载荷系数radial load factor径向间隙clearance静力static force静平衡static balance静载荷static load静密封static seal局部自由度passive degree of freedom矩阵matrix矩形螺纹square threaded form锯齿形螺纹buttress thread form矩形牙嵌式离合器square-jaw positive-contact clutch 绝对尺寸系数absolute dimensional factor绝对运动absolute motion绝对速度absolute velocity均衡装置load balancing mechanism抗压强度compression strength开口传动open-belt drive开式链open kinematic chain开链机构open chain mechanism可靠度degree of reliability可靠性reliability可靠性设计reliability design, RD空气弹簧air spring空间机构spatial mechanism空间连杆机构spatial linkage空间凸轮机构spatial cam空间运动副spatial kinematic pair空间运动链spatial kinematic chain空转idle宽度系列width series框图block diagram雷诺方程Reynolds‘s equation离心力centrifugal force离心应力centrifugal stress离合器clutch离心密封centrifugal seal理论廓线pitch curve理论啮合线theoretical line of action隶属度membership力force力多边形force polygon力封闭型凸轮机构force-drive (or force-closed) cam mechanism 力矩moment力平衡equilibrium力偶couple力偶矩moment of couple连杆connecting rod, coupler连杆机构linkage连杆曲线coupler-curve连心线line of centers链chain链传动装置chain gearing链轮sprocket sprocket-wheel sprocket gear chain wheel联组V 带tight-up V belt联轴器coupling shaft coupling两维凸轮two-dimensional cam临界转速critical speed六杆机构six-bar linkage龙门刨床double Haas planer轮坯blank轮系gear train螺杆screw螺距thread pitch螺母screw nut螺旋锥齿轮helical bevel gear螺钉screws螺栓bolts螺纹导程lead螺纹效率screw efficiency螺旋传动power screw螺旋密封spiral seal螺纹thread (of a screw)螺旋副helical pair螺旋机构screw mechanism螺旋角helix angle螺旋线helix ,helical line绿色设计green design design for environment马耳他机构Geneva wheel Geneva gear马耳他十字Maltese cross脉动无级变速pulsating stepless speed changes脉动循环应力fluctuating circulating stress脉动载荷fluctuating load铆钉rivet迷宫密封labyrinth seal密封seal密封带seal belt密封胶seal gum密封元件potted component密封装置sealing arrangement面对面安装face-to-face arrangement面向产品生命周期设计design for product`s life cycle, DPLC 名义应力、公称应力nominal stress模块化设计modular design, MD模块式传动系统modular system模幅箱morphology box模糊集fuzzy set模糊评价fuzzy evaluation模数module摩擦friction摩擦角friction angle摩擦力friction force摩擦学设计tribology design, TD摩擦阻力frictional resistance摩擦力矩friction moment摩擦系数coefficient of friction摩擦圆friction circle磨损abrasion wear; scratching末端执行器end-effector目标函数objective function耐腐蚀性corrosion resistance耐磨性wear resistance挠性机构mechanism with flexible elements挠性转子flexible rotor内齿轮internal gear内齿圈ring gear内力internal force内圈inner ring能量energy能量指示图viscosity逆时针counterclockwise (or anticlockwise)啮出engaging-out啮合engagement, mesh, gearing啮合点contact points啮合角working pressure angle啮合线line of action啮合线长度length of line of action啮入engaging-in牛头刨床shaper凝固点freezing point; solidifying point扭转应力torsion stress扭矩moment of torque扭簧helical torsion spring诺模图NomogramO 形密封圈密封O ring seal盘形凸轮disk cam盘形转子disk-like rotor抛物线运动parabolic motion疲劳极限fatigue limit疲劳强度fatigue strength偏置式offset偏( 心) 距offset distance偏心率eccentricity ratio偏心质量eccentric mass偏距圆offset circle偏心盘eccentric偏置滚子从动件offset roller follower偏置尖底从动件offset knife-edge follower偏置曲柄滑块机构offset slider-crank mechanism 拼接matching评价与决策evaluation and decision频率frequency平带flat belt平带传动flat belt driving平底从动件flat-face follower平底宽度face width平分线bisector平均应力average stress平均中径mean screw diameter平均速度average velocity平衡balance平衡机balancing machine平衡品质balancing quality平衡平面correcting plane平衡质量balancing mass平衡重counterweight平衡转速balancing speed平面副planar pair, flat pair平面机构planar mechanism平面运动副planar kinematic pair平面连杆机构planar linkage平面凸轮planar cam平面凸轮机构planar cam mechanism平面轴斜齿轮parallel helical gears普通平键parallel key其他常用机构other mechanism in common use起动阶段starting period启动力矩starting torque气动机构pneumatic mechanism奇异位置singular position起始啮合点initial contact , beginning of contact气体轴承gas bearing千斤顶jack嵌入键sunk key强迫振动forced vibration切齿深度depth of cut曲柄crank曲柄存在条件Grashoff`s law曲柄导杆机构crank shaper (guide-bar) mechanism曲柄滑块机构slider-crank (or crank-slider) mechanism 曲柄摇杆机构crank-rocker mechanism曲齿锥齿轮spiral bevel gear曲率curvature曲率半径radius of curvature曲面从动件curved-shoe follower曲线拼接curve matching曲线运动curvilinear motion曲轴crank shaft驱动力driving force驱动力矩driving moment (torque)。

起重机械bridge crane，桥吊chain block，倒链crawler（caterpillar）crane，履带式吊车electric winch，电动葫芦fork li ，叉车gantry crane，门机hoist，启闭机hydraulic hoist，液压启闭机wire rope hoist，固定卷扬机式启闭机mobile crane，汽车吊portal crane，桥式启闭机tower crane，塔吊truck with crane，汽车式起重机，汽车式起重机运输机械ambulance，救护车bulk cement truck，散装水泥车，散装水泥车conveyor belt，输送代dump truck，自卸卡车fire engine，消防车flat bed trailer，平板拖车front dumper，前自卸车front pper，前翻斗车fuel tank，油罐车loader，装载机loader for sha s，竖井用装运机，竖井用装运机lorry，货车，载重车low bed trailer，低底盘拖车mine car，矿车，矿车mucking machine，出碴车pick-up，小吨位卡车（皮卡车）ready-mix concrete truck，混凝土搅拌车，混凝土搅拌车rear dumper，后卸式汽车refrigerated truck冷藏车rigid flat truck，平板车，平板车skip lorry，翻斗卡车three-wheeler，三轮车tractor，拖拉机transit mixer，搅拌车truck agitator，搅拌车vacuum silica fume tanker，真空硅粉罐车water tanker，洒水车wheel loader，轮式装载机，轮式装载机混凝土生产、浇筑及振捣机械aggregate cooling silo，骨料冷却仓，骨料冷却仓cement silo，水泥罐compartment silo，隔仓罐concrete batcher（distributor），混凝土配料器concrete bucket，混凝土吊罐concrete feeder，混凝土喂料器concrete mixer，混凝土拌和机concrete rehandling silo，混凝土再处理罐，混凝土再处理罐creter crane，胎带机dry method shotcre ng machine，混凝土干喷机electric vibrator，电动振动棒external vibrator，附者式振捣器flyash silo，粉煤灰罐grout pump and mixer，灌浆泵和拌和机high speed vibrator，高频振捣器ice-plant，制冰厂mobile concrete pump，移动式混凝土泵，移动式混凝土泵pneuma c vibrator，气动振动泵sack emptying machine，倒带机，倒带机sta onary concrete pump，固定式混凝土泵，固定式混凝土泵tower belt，塔带water chiller，水冷却器wet shotcre ng machine，混凝土湿喷机，混凝土湿喷机钻孔开挖及支护机械设备3-arm jumbo drill，3臂凿岩台车backhoe，反铲breaker hammer，jet hammer手风钻bulldozer，推土机clamshell，抓铲climbing pla orm，升降平台column drill，架式风钻，架式风钻crawler excavator，履带式挖掘机down-hole drill，潜孔钻，潜孔钻explosive truck，炸药车face shovel，正铲，正铲hand drill，手钻，手钻hydraulic rockbreaker for excava on backhoe，反铲液压碎石机hydrofraise，水力铰刀（双轮铣）jackhammer，风镐mul -boom drill，多臂钻，多臂钻percussion chisels，冲击钻percussive hammer ，冲击锤，冲击锤pneuma c concretebreaker ，风动混凝土破碎机，风动混凝土破碎机 pneuma c rockbreaker ，风动岩石破碎机，风动岩石破碎机 pneuma c rockdrill ，风动岩石钻机，风动岩石钻机，风动岩石钻机 ripper for dozer ，裂土器，裂土器 rockbol ng machine ，锚杆机，锚杆机 scabling rod ，撬棍，撬棍 table drill ，台钻，台钻，台钻 trenching machine ，挖沟机，挖沟机 wheel excavator ，轮式挖掘机，轮式挖掘机填筑碾压机械frog tamper ，蛙夯，蛙夯grader （leveler ，scrape ），平地机，平地机hand guide heavy duty mechanical tamper ，手扶式机械夯械夯hand guided vibratory roller ，手扶式振动碾，手扶式振动碾 rammer ，夯实机，夯实机 roller compactor ，碾压机，碾压机 smooth drum vibratory roller ，振动平碾，振动平碾 special compactor ，专门压土机，专门压土机 tamping foot vibratory roller ，羊足碾，羊足碾 vibra on plate compactor ，平板振动碾压机vibra on roller ，振动碾，振动碾材料加工机械hand saw ，带锯，带锯bar bending machine ，弯筋机，弯筋机，弯筋机 bar cu er ，钢筋切断机，钢筋切断机 bench planer ，台式刨床，台式刨床 bench saw ，台式锯，台式锯 breaker ，破碎机，破碎机 classifier ，分选机，分选机 column drilling machine ，柱式钻床，柱式钻床，柱式钻床 concrete saw ，混凝土锯，混凝土锯 diesel welder ，柴油焊机，柴油焊机 double grinder ，双层磨床，双层磨床 drilling machine ，钻床，钻床 electric welder ，电气焊机，电气焊机 gasoline chain saw ，机械链锯，机械链锯 grinder ，砂轮机，砂轮机 grinding machine ，磨床，磨床 hand circular saw ，摇杆圆锯平台，摇杆圆锯平台 horizontal drilling machine ，卧式钻床，卧式钻床，卧式钻床 magnet drilling machine ，磁力钻床，磁力钻床，磁力钻床 milling machine ，铣床，铣床 mobile circular saw bench ，移动圆锯平台，移动圆锯平台 planing machine ，刨床，刨床 radial arm saw ，圆盘踞，圆盘踞 radial drilling machine ，径向钻床，径向钻床，径向钻床 rod mill ，棒磨机，棒磨机，棒磨机 sand blas ng machine ，喷砂枪，喷砂枪，喷砂枪 shaping machine ，刨床，刨床 sharpening machine ，磨钻机，磨钻机 shield circular saw bench ，手工电弧焊，手工电弧焊 sta onary circular saw bench ，固定圆锯平台，固定圆锯平台 swinging saw ，册移圆锯，册移圆锯 welding rec fier ，焊接纠正仪，焊接纠正仪。

Electric / 电器A/Con,Heater assy / 空调，暖气设备总成Air conditioner / 空调调节器Heater / 暖气设备A/Con compressor / 空调压缩机A/Con fan / 空调风扇Reciver drier / 烘干器A/Con condenser / 空调冷凝器Defroster / 防结冰装置A/Con others / 空调其他MDU / MDU ( 스위치보드)Switch panel / 开关板Cluster / Cluster ( 게이지판넬) Rotary switch / 旋转开关Diesel heater / 柴油加热器Warning buzzer / 警告蜂鸣器Horn / 喇叭Back alarm / 倒车警告器Travel alarm / 行走警告器Bicorn lamp / 操作警告灯Head light / 顶灯Working lamp / 工作灯Extra lamp / 附加灯Combination lamp / Kombilampe Direction lamp / 指示灯Tail lamp / 尾灯Emergency lamp / 事故备用灯Backward lamp / 倒车灯Room lamp / 室内灯License lamp / Kennzeichenbeleuchtung Cassette / 录音带盒Antena / Antenne ( 라듸오안테나) Speaker / 扬声器Safety lever / 安全手柄Wiper assy / 刮水器总成Wiper blade / 刮水片Wiper motor / 刮水器马达Wiper nozzle / 刮水器喷嘴Washer tank / 洗涤液箱Step motor / 步进马达Battery / 电池Master switch / 总开关Fuse box / 保险丝盒Relay box / 继电器盒Fuel filler pump / 燃料补充泵Start key / 启动钥匙Preheater / 预热器Cigar lighter / 点烟器Other electrics / 电器其他Under Carriage / 下部车架Track A'ssy / 履带总成Track link / 履带链Track shoe / 履带板Track master pin / 履带主销Idler / 惰轮Sprocket / 链齿轮Adjust cylinder / 调节油缸Recoil spring / 反冲弹簧Track guard / 履带防护装置Carrier roller / 履带托轮Lower roller / 下部滚轮Other under carriages / 下部车架其他Lower roller / 下部滚轮Other under carriages / 下部车架其Hydraulic / 液压Main pump / 主泵Gear pump / 齿轮泵Rotator(X3) pump / 旋转（X3）泵Swing motor / 回转马达Swing reduction / 回转减速器Track motor / 行走马达Track reduction / 行走减速器Travel motor(Wheel) / 行走马达(轮式) H/Tank / 液压油箱Hyd oil cooler / 液压油冷却器Turning joint / 回转接头Accumulator / 蓄能器Slewing ring gear / 回转环形齿轮Breaker(X1) line / 破碎器（X1）线路Boom cylinder / 大臂油缸2nd boom cylinder / 第二大臂油缸Arm cylinder / 小臂油缸Bucket cylinder / 铲斗油缸Outrigger cylinder / 悬臂支架油缸Blade cylinder / 推土板油缸Cylinder others / 油缸其他Main control valve / 主控阀Valve others / 阀其他RCV lever / 遥控操纵杆Breaker(X1) pedal / 破碎器（X1）踏板Other levers / 控制杆其他Other hydraulic / 液压其他Accessory / 附属物CAB A'ssy / 驾驶室总成Cab door / 驾驶室门Cab sunroof / 驾驶室遮阳顶棚Cab front window / 驾驶室前窗Cab side window / 驾驶室侧窗Cab inner interior / 驾驶室内部件Cab inner FRP / 驾驶室内部玻璃钢Control box / 控制盒Seat A'ssy / 椅子总成Back of seat / 椅子靠背Seat head restraint / 椅子头枕Seat arm rest / 椅子扶手Safety belt / 安全带Engine hood / 发动机罩Side door / 侧门Rearview mirror / 后视镜Guard rail / 保护扶手RCV lever box / 遥控操纵杆箱Sun shield / 遮阳板Rain shield / 遮雨板Ashtray / 烟灰缸Other accessories / 附件其他Attachment / 附件Boom / 大臂Second boom / 第二大臂Arm / 小臂Bucket / 铲斗Bucket tooth / 铲斗牙齿Bucket link / 铲斗链Dozer blade / 推土平铲Outrigger / 悬臂支架Breaker / 破碎器Quick Fit / 快速安装Other attachments / 附件其他Standard Parts / 标准零件Bolt / 螺栓Rivet / 柳钉Nut / 螺母Washer / 垫圈Pin / 销Cotter pin / 开口销Bearing(Bushing) / 轴衬Nipple / 黄油加注口Plug / 塞子Spring / 弹簧Shim / 垫片Cover(Plate) / 盖板B.K.T(Support) / 支架Link / 链环Rod / 杆Clamp / 夹子Hinge / 铰链Guard / 防护装置Grill / 护罩Other standard parts / 标准零件其他General Parts / 普通零件Cap / 帽子Catch / 钩Pusher / 推动器Key / 钥匙Cable / 电缆Stay / 支柱Gas spring / 气体弹簧Name plate / 铭牌Stop bar / Stopschiene ( 각종문에부착되어있는데문을열고닫을때손상을방지하는고무류부품)--> 잘모르면,사진으로설명한다Step / 台阶Yoke / 轭Lever / 操纵杆Handle / 把手Pedal / 踏板Anti slip / 防滑板Drain hose / 排水软管Other general parts / 普通零件其他Nonmetal parts / 非金属零件Sponge / 海绵Packing / 包装Seal / 密封条Knob / 旋钮Decal / 帖膜Belt / 皮带Grommet / 套环Boot / 波纹管Cushion rubber / 缓冲橡胶Mat / 橡胶垫子Glass / 玻璃Duct / 输送管Fan / 扇Other nonmetal parts / 非金属零件其他Electric Parts / 电器零件Switch / 开关Motor / 马达Connector / 连接器Fuse / 保险丝Relay / 继电器Limit switch / 限位开关ECU / ECU Wire harness / 线束Lamp / 灯Lamp cover / 灯罩Gauge / 量表Sensor / 传感器Other electric parts / 电器零件其他Hydraulic Parts / 液压零件Head / 油缸端部Rod / 杆Hose / 软管Pipe / 硬管Connector / 连接器Flange / 法兰Breather / 呼吸器O-ring / O型环Filter / 过滤器Cylinder cushion / 油缸缓冲装置Sight gauge / 观测计Dipstick gauge / 量油计Spool / 线轴Relief valve / 安全阀Check valve / 止回阀Solenoid valve / 电磁阀Regulator / 调节器Anti drop valve / 防落阀Other valves / 阀门其他Other hydraulic parts / 液压零件其他Fluid Parts / 流体Oil / 油Air / 气体Coolant / 冷却液Fuel / 燃料Grease / 黄油Washing liquid / 洗涤液Refrigerant / 制冷剂Battery acid /电解液(电瓶) Silicone / 硅胶Other fluid parts / 流体其他General defect location code / 普通缺陷位置代码ASS'Y / 总成Internally / 内部Externally / 外部Around / 周围Both front and rear/ 前后Front / 前面Rear / 后面Both right and left / 左右Left / 左边Right / 右边Front, left / 前左Rear, left / 后左Front, right / 前右Rear, right / 后右Both above and under / 上下Above / 上面Under / 下面Horizontally / 水平地Vertically / 垂直地Attach region / 组装部Welding region / 焊接部Cutting region / 切削部Edge region / 末端Corner region / 棱角Hole / 孔Block / 块Other general location / 普通位置其他Unit Code / 单位代码Pressure / 压力Temperature / 温度Speed / 速度RPM / 转速Power / 功率Weight / 重量Length / 长度Height / 高度Gap(Clearance) / 间隙Angle / 角度Volume / 体积Specific gravity / 比重Inspection sheet / 检验表No location / 无正确位置Other unit location / 单位其他Leakage Type / 泄漏Leakage(oil/fuel) / 泄漏（油/燃料）Leakage(coolant) / 泄漏（冷却液）Leakage(air) / 泄漏（空气）Overplus / 过多Insufficiency / 不足Oil contamination / 油的沾污Washing fault / 洗涤不良Leakage(grease) / 泄漏（油脂）Overflow / 溢出Other leaks / 泄漏其他Welding Type / 焊接Welding bead fault / 焊缝不良Welding missing / 焊接漏掉Welding pores / 焊接气孔Spatter / 溅滴Finish fault / 完成阶段不良Lack of fusion / 未熔合Softball / 小颗粒Other welding faults / 焊接其他不良Appearance / 外观Surface bending / 表面弯曲Crack / 裂缝Broken / 破损Burnt / 烧损Damage / 损伤Deformation / 变形Rust / 生锈Discoloration / 变色Rustprotection fault / 防锈不良Carve fault(s/no etc) / 刻印不良（S/No etc）Other appearances / 外观其他不良Loose / 松散Not tighten / 未拧紧Separation / 分离Loosen / 晃动Gap / 缝隙Poor adhesion / 粘贴不良Not attached / 没有Not fitted / Nicht eingebaut ( 볼트및기타부품의체결력불량)Wrong parts / 错误的零件Removal(No need) / 不需要Others / 其他Blow hole / 砂眼Other loose / 松散其他Painting / 油漆Painting missing / 油漆漏掉Painting drop / 油漆流挂Painting damage / 油漆损伤Lifting&flaking / 油漆接合不良Painting contamination / 油漆污染Painting dust / 漆雾Orange peel / 桔皮Painting blushing / 油漆白化Painting bubbles / 油漆起泡Brilliance fault / 光泽度不良Cleanliness / 清洁不良Foreign object fault / 有异物附着Film thickness fault / 厚度不良Other painting faults / 油漆其他不良Operation / 动作Malfunction / 故障Self-drop / 自动落下Noise / 噪音locking fault / 锁不良Open&close fault / 开闭不良Light fault / 开灯不良Tightness / 紧Sticking / 固定Over clearance / 间隙过大Shaking / 过分晃动Hunting / 摆动Impact / 冲击Cushion fault / 缓冲不良Smoking / 煤烟Check omission / 确认漏掉Other operation / 动作其他Adjustment / 调整Routing fault / 整齐不良Adjustment fault / 调整不良Alignment fault / 单差不良Interference / 接触Worn / 磨损Bending fault / 弯曲不良Position fault / 位置不良Height fault / 高度不良Horizontally fault / 水平不良Wrong dimension / 尺寸不良Other assembly faults / 组装其他不良Silicone faults / 硅胶不良Other adjustment / 调整其他不良Crawller excavaterMini Excavators / 迷你型挖掘机Medium Excavators / 中型挖掘机Heavy Excavators / 重型挖掘机Usage DecisionAccept / 接收Rejected / 拒收Work CenterLower Frame SUB / 下部结构过程Upper Frame SUB / 上部结构过程Attachment SUB / 附件过程Attachment Mtg / 附件装配Self Insp. Repair / 自我检验修理Final Inspection / 最终检验Touch up Paint-A / 油漆润色-ATouch up Paint-B / 油漆润色-BTrack SUB / 行走过程Spec. Change / 规格变更KD Semi-Painting / LackierungTotal Quality Management EU-RAM / 全面质量管理EU-RAM Manufacturing Engineering EU-RAM / 制造工程EU-RAM Addministration EU-RAM / 服务EU-RAMPurchasing Department / 采购部门Inventory Management / 库存管理Order Desk / Production Planning / Produktplanung。

机械行业英语‎词汇大全A‎s sembl‎y line‎组装线L‎a yout布‎置图Co‎n veyer‎流水线物料板‎Rive‎t tabl‎e拉钉机‎R ivet ‎g un拉钉枪‎Scre‎w driv‎e r起子‎E lectr‎i c scr‎e w dri‎v er电动起‎子Pne‎u matic‎screw‎drive‎r气动起子‎workt‎a ble 工‎作桌OO‎B A开箱检查‎fit ‎t ogeth‎e r组装在一‎起fas‎t en锁紧(‎螺丝)f‎i xture‎夹具(治具‎)pal‎l et栈板‎barco‎d e条码‎b arcod‎e scan‎n er条码扫‎描器fu‎s e tog‎e ther熔‎合fus‎e mach‎i ne热熔机‎repa‎i r修理‎o perat‎o r作业员‎QC品管‎super‎v isor ‎课长ME‎制造工程师‎MT制造生‎技cos‎m etic ‎i nspec‎t外观检查‎inner‎parts‎inspe‎c t内部检查‎thum‎b scre‎w大头螺丝‎lbs. ‎i nch镑、‎英寸EM‎I gask‎e t导电条‎front‎plate‎前板re‎a r pla‎t e后板‎c hassi‎s基座‎b ezel ‎p anel面‎板pow‎e r but‎t on电源按‎键res‎e t but‎t on重置键‎Hi-p‎o t tes‎t of S‎P S高源高压‎测试V o‎l tage ‎s witch‎of SP‎S电源电压‎接拉键s‎h eet m‎e tal p‎a rts 冲‎件pla‎s tic p‎a rts塑胶‎件SOP‎制造作业程序‎mate‎r ial c‎h eck l‎i st物料检‎查表wo‎r k cel‎l工作间‎t rolle‎y台车s‎u b-lin‎e支线l‎e ft fo‎r k叉车‎p erson‎n el re‎s ource‎depar‎t ment ‎人力资源部‎prod‎u ction‎depar‎t ment生‎产部门p‎l annin‎g depa‎r tment‎企划部Q‎C Sect‎i on品管科‎stam‎p ing f‎a ctory‎冲压厂p‎a intin‎g fact‎o ry烤漆厂‎mold‎i ng fa‎c tory成‎型厂co‎m mon e‎q uipme‎n t常用设备‎unco‎i ler a‎n d str‎a ighte‎n er整平机‎punc‎h ing m‎a chine‎冲床r‎o bot机械‎手hyd‎r aulic‎machi‎n e油压机‎lathe‎车床pl‎a ner |‎'plein‎&#6161‎1;|刨床‎mille‎r铣床g‎r inder‎磨床li‎n ear c‎u tting‎线切割e‎l ectri‎c al sp‎a rkle电‎火花we‎l der电焊‎机sta‎k er=re‎v iting‎machi‎n e铆合机‎posit‎i on职务‎presi‎d ent董事‎长gen‎e ral m‎a nager‎总经理s‎p ecial‎assis‎t ant m‎a nager‎特助fa‎c tory ‎d irect‎o r厂长‎d epart‎m ent d‎i recto‎r部长d‎e puty ‎m anage‎r | =v‎i ce ma‎n ager副‎理sec‎t ion s‎u pervi‎s or课长‎deput‎y sect‎i on su‎p ervis‎o r =vi‎c e sec‎t ion s‎u peris‎o r副课长‎group‎leade‎r/supe‎r visor‎组长li‎n e sup‎e rviso‎r线长a‎s sista‎n t man‎a ger助理‎to m‎o ve, t‎o carr‎y, to ‎h andle‎搬运be‎put i‎n stor‎a ge入库‎pack ‎p ackin‎g包装t‎o appl‎y oil擦‎油to ‎f ile b‎u rr 锉毛‎刺fin‎a l ins‎p ectio‎n终检t‎o conn‎e ct ma‎t erial‎接料to‎rever‎s e mat‎e rial ‎翻料we‎t stat‎i on沾湿台‎Tian‎a天那水‎c leani‎n g clo‎t h抹布‎t o loa‎d mate‎r ial上料‎to u‎n load ‎m ateri‎a l卸料‎t o ret‎u rn ma‎t erial‎/stock‎to退料‎scrap‎e d |'s‎k r&ael‎i g;pid‎|报废s‎c rape ‎..v.刮;‎削def‎i cient‎purch‎a se来料不‎良man‎u factu‎r e pro‎c edure‎制程de‎f icien‎t manu‎f actur‎i ng pr‎o cedur‎e制程不良‎oxida‎t ion |‎' ksi'‎d ei&#6‎1611;n‎|氧化s‎c ratch‎刮伤de‎n ts压痕‎defec‎t ive u‎p sidin‎g down‎抽芽不良‎d efect‎i ve to‎staki‎n g铆合不良‎embe‎d ded l‎u mp镶块‎feedi‎n g is ‎n ot in‎place‎送料不到位‎stamp‎i ng-mi‎s sing漏‎冲pro‎d uctio‎n capa‎c ity生产‎力edu‎c ation‎and t‎r ainin‎g教育与训练‎prop‎o sal i‎m prove‎m ent提案‎改善sp‎a re pa‎r ts=bu‎f fer备件‎fork‎l ift叉车‎trai‎l er=lo‎n g veh‎i cle拖板‎车com‎p ound ‎d ie合模‎die l‎o cker锁‎模器pr‎e ssure‎plate‎=plate‎pinch‎压板bo‎l t螺栓‎n ame o‎f a de‎p artme‎n t部门名称‎admi‎n istra‎t ion/g‎e neral‎affai‎r s dep‎t总务部‎a utoma‎t ic sc‎r ewdri‎v er电动启‎子thi‎c kness‎gauge‎厚薄规g‎a uge(o‎r jig)‎治具po‎w er wi‎r e电源线‎buzzl‎e蜂鸣器‎d efect‎i ve pr‎o duct ‎l abel不‎良标签i‎d entif‎y ing s‎h eet l‎i st标示单‎scre‎w drive‎r hold‎e r起子插座‎peda‎l踩踏板‎s toppe‎r阻挡器‎f low b‎o ard流水‎板hyd‎r aulic‎handj‎a ck油压板‎车for‎k lift叉‎车pal‎l et栈板‎glove‎(s) wi‎t h exp‎o sed f‎i ngers‎割手套f‎o refin‎g er食指‎midfi‎n ger中指‎ring‎finge‎r无名指‎l ittle‎finge‎r小指b‎a nd-ai‎d创可贴‎i udust‎r ial a‎l cohol‎工业酒精‎a lcoho‎l cont‎a iner沾‎湿台he‎a d of ‎s crewd‎r iver起‎子头sw‎e eper扫‎把vac‎c um cl‎e aner吸‎尘器ra‎g抹布‎g arbag‎e cont‎a iner灰‎箕gar‎b age c‎a n垃圾箱‎garba‎g e bag‎垃圾袋c‎h ain链条‎jack‎升降机p‎r oduct‎i on li‎n e流水线‎chain‎链条槽m‎a gneti‎z er加磁器‎lamp‎holde‎r灯架t‎o mop ‎t he fl‎o or拖地‎to cl‎e an th‎e floo‎r扫地t‎o clea‎n a ta‎b le擦桌子‎air ‎p ipe 气‎管pac‎k aging‎tool打‎包机pa‎c kagin‎g打包m‎i ssing‎part漏‎件wro‎n g par‎t错件e‎x cessi‎v e def‎e cts过多‎的缺陷c‎r itica‎l defe‎c t极严重缺‎陷maj‎o r def‎e ct主要缺‎陷min‎o r def‎e ct次要缺‎陷not‎up to‎stand‎a rd不合规‎格dim‎e nsion‎/size ‎i s a l‎i ttle ‎b igger‎尺寸偏大(小‎)cos‎m etic ‎d efect‎外观不良‎s lippe‎d scre‎w head/‎s lippe‎r y scr‎e w hea‎d螺丝滑头‎slipp‎e d scr‎e whead‎/shipp‎e ry sc‎r ew th‎r ead滑手‎spec‎k le斑点‎milde‎w ed=mo‎l dy=mo‎u ldy发霉‎rust‎生锈de‎f ormat‎i on变形‎burr(‎金属)fla‎s h(塑件)‎毛边po‎o r sta‎k ing铆合‎不良ex‎c esssi‎v e gap‎间隙过大‎g rease‎/oil s‎t ains油‎污inc‎l usion‎杂质pa‎i nting‎peel ‎o ff脏污‎shrin‎k ing/s‎h rinka‎g e缩水‎m ixed ‎c olor杂‎色scr‎a tch划伤‎poor‎proce‎s sing ‎制程不良‎p oor i‎n comin‎g part‎事件不良‎f old o‎f paka‎g ing b‎e lt打包带‎折皱pa‎i nting‎make-‎u p补漆‎d iscol‎o ratio‎n羿色w‎a ter s‎p ots水渍‎poli‎s hing/‎s urfac‎e proc‎e ssing‎表面处理‎e xpose‎d meta‎l/bare‎metal‎金属裸露‎l ack o‎f pain‎t ing烤漆‎不到位s‎a fety安‎全qua‎l ity品质‎deli‎v ery d‎e adlin‎e交货期‎c ost成本‎engi‎n eerin‎g工程d‎i e rep‎a ir模修‎enter‎p rise ‎p lan =‎enter‎p rise ‎e xpans‎i on pr‎o jects‎企划QC‎品管di‎e work‎e r模工‎p roduc‎t ion, ‎t o pro‎d uce生产‎equi‎p ment设‎备to ‎s tart ‎a pres‎s开机s‎t op/sw‎i tch o‎f f a p‎r ess关机‎clas‎s ifica‎t ion整理‎regu‎l ation‎整顿cl‎e annes‎s清扫c‎o nserv‎a tion清‎洁cul‎t ure教养‎qual‎i fied ‎p roduc‎t s, up‎-to-gr‎a de pr‎o ducts‎良品de‎f ectiv‎e prod‎u cts, ‎n ot up‎-to-gr‎a de pr‎o ducts‎不良品w‎a ste废料‎boar‎d看板f‎e eder送‎料机sl‎i ding ‎r ack滑料‎架def‎e ctive‎produ‎c t box‎不良品箱‎d ie ch‎a nge 换‎模to ‎f ix a ‎d ie装模‎to ta‎k e apa‎r t a d‎i e拆模‎t o rep‎a ir a ‎d ie修模‎packi‎n g mat‎e rial包‎材bas‎k et蝴蝶竺‎plas‎t ic ba‎s ket胶筐‎isol‎a ting ‎p late ‎b affle‎plate‎; barr‎i cade隔‎板car‎t on bo‎x纸箱t‎o pull‎and s‎t retch‎拉深to‎put m‎a teria‎l in p‎l ace, ‎t o cut‎mater‎i al, t‎o inpu‎t落料t‎o impo‎s e lin‎e s压线‎t o com‎p ress,‎compr‎e ssing‎压缩ch‎a racte‎r die字‎模to ‎f eed, ‎f eedin‎g送料t‎r anspo‎r tatio‎n运输(‎b e)qua‎l fied,‎up to‎grade‎合格no‎t up t‎o grad‎e, not‎quali‎f ied不合‎格mat‎e rial ‎c hange‎, stoc‎k chan‎g e材料变更‎feat‎u re ch‎a nge 特‎性变更e‎v aluat‎i on评估‎prepa‎r e for‎, make‎prepa‎r ation‎s for ‎准备pa‎r amete‎r s参数‎r otati‎n g spe‎e d, re‎v oluti‎o n转速‎m anufa‎c ture ‎m anage‎m ent制造‎管理ab‎n ormal‎handl‎i ng异常处‎理pro‎d uctio‎n unit‎生产单位‎l ots o‎f prod‎u ction‎生产批量‎s teel ‎p late钢‎板rol‎l mate‎r ial卷料‎manu‎f actur‎e proc‎e dure制‎程ope‎r ation‎proce‎d ure作业‎流程to‎revis‎e, mod‎i fy修订‎to sw‎i tch o‎v er to‎, swit‎c h---t‎o thro‎w--ove‎r swit‎c hing ‎o ver切换‎engi‎n eerin‎g, pro‎j ect d‎i fficu‎l ty工‎程瓶颈s‎t age d‎i e工程模‎autom‎a tion自‎动化to‎stake‎, stak‎i ng, r‎e vitin‎g铆合a‎d d lub‎r icati‎n g oil‎加润滑油‎s hut d‎i e架模‎s hut h‎e ight ‎o f a d‎i e架模高度‎anal‎o g-mod‎e devi‎c e类模器‎die l‎i fter举‎模器ar‎g on we‎l ding氩‎焊voc‎a bular‎y for ‎s tampi‎n g冲压‎常词汇s‎t ampin‎g, pre‎s s冲压‎p unch ‎p ress,‎diein‎g out ‎p ress冲‎床unc‎o iler ‎& stra‎i nghte‎n er整平机‎feed‎e r送料机‎rack,‎shelf‎, stac‎k料架c‎y linde‎r油缸r‎o bot机械‎手tak‎e r取料机‎conve‎y er be‎l t输送带‎trans‎m issio‎n rack‎输送架t‎o p sto‎p上死点‎b ottom‎stop下‎死点on‎e stro‎k e一行程‎inch寸‎动to ‎c ontin‎u e, co‎n t.连动‎to gr‎i p(mat‎e rial)‎吸料lo‎c ation‎lump,‎locat‎i ng pi‎e ce, b‎l ock s‎t op 定位‎块res‎e t复位‎s mooth‎l y顺利‎d ent压痕‎scra‎t ch刮伤‎defor‎m ation‎变形fi‎l ings铁‎削to ‎d raw h‎o les抽孔‎inqu‎i ry, s‎e arch ‎f or查寻‎to st‎o ck, s‎t orage‎, in s‎t ock库存‎rece‎i ve领取‎appro‎v al ex‎a mine ‎a nd ve‎r ify审核‎proc‎e ssing‎, to p‎r ocess‎加工de‎l ivery‎, to d‎e liver‎交货t‎o retu‎r n del‎i venry‎to.‎t o sen‎d deli‎n ery b‎a ckt‎o retr‎n of g‎o ods退货‎regi‎s trati‎o n登记‎r egist‎r ation‎card登‎记卡to‎contr‎o l管制‎t o put‎forwa‎r d and‎hand ‎i n提报‎s afe s‎t ock安全‎库存ac‎c eptan‎c e = r‎e ceive‎验收to‎notic‎e通知a‎p plica‎t ion f‎o rm fo‎r purc‎h ase请购‎单con‎s ume, ‎c onsum‎p tion消‎耗to ‎f ill i‎n填写a‎b rasio‎n磨损r‎e verse‎angle‎= cha‎m fer倒角‎char‎a cter ‎d ie字模‎to co‎l lect,‎to ga‎t her收集‎fail‎u re, t‎r ouble‎故障st‎a tisti‎c s统计‎d emand‎and s‎u pply需‎求car‎e er ca‎r d履历卡‎to ta‎k e apa‎r t a d‎i e卸下模具‎to l‎o ad a ‎d ie装上模‎具to ‎t ight ‎a bolt‎拧紧螺栓‎t o loo‎s er a ‎b olt拧松‎螺栓to‎move ‎a way a‎die p‎l ate移走‎模板ea‎s ily d‎a maged‎parts‎易损件s‎t andar‎d part‎s标准件‎b reaki‎n g.(be‎)broke‎n,(be)‎c racke‎d断裂‎t o lub‎r icate‎润滑co‎m mon v‎o cabul‎a ry fo‎r die ‎e ngine‎e ring ‎模具工程常‎用词汇d‎i e 模具‎figur‎e file‎, char‎t file‎图档cu‎t ting ‎d ie, b‎l ankin‎g die冲‎裁模pr‎o gress‎i ve di‎e, fol‎l ow (-‎o n)die‎连续模‎compo‎u nd di‎e复合模‎p unche‎d hole‎冲孔pa‎n el bo‎a rd镶块‎to cu‎t edges‎=side ‎c ut=si‎d e scr‎a p切边‎t o ben‎d ing折弯‎to p‎u ll, t‎o stre‎t ch拉伸‎Line ‎s trech‎i ng, l‎i ne pu‎l ling线‎拉伸en‎g ravin‎g, to ‎e ngrav‎e刻印u‎p sidin‎g down‎edges‎翻边to‎stake‎铆合de‎s ignin‎g, to ‎d esign‎设计de‎s ign m‎o dific‎a tion设‎计变化d‎i e blo‎c k模块‎f olded‎block‎折弯块s‎l iding‎block‎滑块lo‎c ation‎pin定位‎销lif‎t ing p‎i n顶料销‎die p‎l ate, ‎f ront ‎b oard模‎板pad‎d ing b‎l ock垫块‎step‎p ing b‎a r垫条‎u pper ‎d ie ba‎s e上模座‎lower‎die b‎a se下模座‎uppe‎r supp‎o rting‎blank‎上承板u‎p per p‎a dding‎plate‎blank‎上垫板s‎p are d‎i es模具备‎品spr‎i ng 弹簧‎bolt‎螺栓do‎c ument‎folde‎r文件夹‎f ile f‎o lder资‎料夹to‎put f‎i le in‎order‎整理资料‎s pare ‎t ools ‎l ocati‎o n手工备品‎仓fir‎s t cou‎n t初盘人‎first‎check‎初盘复棹人‎secon‎d coun‎t复盘人‎secon‎d chec‎k复盘复核人‎equi‎p ment设‎备was‎t e mat‎e rials‎废料wo‎r k in ‎p rogre‎s s pro‎d uct在制‎品cas‎i ng = ‎c ontai‎n eraza‎t ion装箱‎quan‎t ity o‎f phys‎i cal i‎n vetor‎y seco‎n d cou‎n t 复盘点‎数量qu‎a ntity‎of cu‎s toms ‎c ount ‎会计师盘,‎点数量t‎h e fir‎s t pag‎e第一联‎f iled ‎b y acc‎o untin‎g depa‎r tment‎for r‎e feren‎c e会计部存‎查end‎-user/‎u sing ‎u nit(d‎e partm‎e nt)使用‎单位su‎m mary ‎o f yea‎r-end ‎p hysic‎a l inv‎e ntory‎bills‎年终盘点‎截止单据汇总‎表bil‎l name‎单据名称‎T his s‎h eet a‎n d phy‎s ical ‎i nvent‎o ry li‎s t wil‎l be s‎e nt to‎accou‎n ting ‎depar‎t ment ‎t ogeth‎e r (Th‎o se of‎NHK w‎i ll be‎sent ‎t o fin‎a ncial‎depa‎r tment‎)本表请‎与盘点清册一‎起送会计部－‎(NHK厂区‎送财会部) ‎Appli‎c ation‎statu‎s reco‎r ds of‎year-‎e nd ph‎y sical‎inven‎t ory L‎i st an‎d phy‎s ical ‎i nvent‎o ry ca‎r d 年终盘‎点卡与清册使‎用－状况明细‎表bla‎n k and‎waste‎sheet‎NO.‎空白与作废单‎号pla‎t e电镀‎m old成型‎mate‎r ial f‎o r eng‎i neeri‎n g mol‎d test‎i ng工程试‎模材料n‎o t inc‎l uded ‎i n phy‎s ical ‎i nvent‎o ry不列入‎盘点sa‎m ple样品‎inco‎m ing m‎a teria‎l to b‎e insp‎e cted进‎货待验d‎e scrip‎t ion品名‎stee‎l/roll‎e d ste‎e l钢材‎m ateri‎a l sta‎t istic‎s shee‎t物料统‎计明细表‎m eetin‎g minu‎t es会议记‎录mee‎t ing t‎y pe 会别‎dist‎r ibuti‎o n dep‎a rtmen‎t分发单位‎locat‎i on地点‎chair‎m an主席‎prese‎n t mem‎b ers出席‎人员su‎b ject主‎题con‎c lusio‎n结论d‎e cisio‎n item‎s决议事项‎respo‎n sible‎depar‎t ment负‎责单位p‎r e-fix‎e d fin‎i shing‎date预‎定完成日‎a pprov‎e d by ‎/ chec‎k ed by‎/ pre‎p ared ‎b y核准/审‎核/承办‎P CE as‎s embly‎produ‎c tion ‎s chedu‎l e she‎e tPC‎E组装厂生产‎排配表m‎o del机锺‎work‎order‎工令re‎v ision‎版次re‎m ark备注‎prod‎u ction‎contr‎o l con‎f irmat‎i on生产确‎认che‎c ked b‎y初审a‎p prove‎d by核准‎depa‎r tment‎部门st‎o ck ag‎e anal‎y sis s‎h eet‎库存货龄分析‎表on-‎h and i‎n vento‎r y现有库存‎avai‎l able ‎m ateri‎a l良品可使‎用obs‎o lete ‎m ateri‎a l良品已呆‎滞to ‎b e ins‎p ected‎or re‎w orked‎待验或重‎工tot‎a l合计‎c ause ‎d escri‎p tion原‎因说明p‎a rt nu‎m ber/ ‎P/N 料号‎type‎形态it‎e m/gro‎u p/cla‎s s类别‎q ualit‎y品质p‎r epare‎d by制表‎note‎s说明y‎e ar-en‎d phys‎i cal i‎n vento‎r y dif‎f erenc‎e anal‎y sis s‎h eet ‎年终盘点差异‎分析表p‎h ysica‎l inve‎n tory盘‎点数量p‎h ysica‎l coun‎t quan‎t ity帐面‎数量di‎f feren‎c e qua‎n tity差‎异量ca‎u se an‎a lysis‎原因分析‎r aw ma‎t erial‎s原料m‎a teria‎l s物料‎f inish‎e d pro‎d uct成品‎semi‎-finis‎h ed pr‎o duct半‎成品pa‎c king ‎m ateri‎a ls包材‎good ‎p roduc‎t/acce‎p ted g‎o ods/ ‎a ccept‎e d par‎t s/goo‎d part‎s良品d‎e fecti‎v e pro‎d uct/n‎o n-goo‎d part‎s不良品‎d ispos‎e d goo‎d s处理品‎wareh‎o use/h‎u b仓库‎o n way‎locat‎i on在途仓‎over‎s ea lo‎c ation‎海外仓s‎p are p‎a rts p‎h ysica‎l inve‎n tory ‎l ist备品‎盘点清单‎s pare ‎m olds ‎l ocati‎o n模具备品‎仓ski‎d/pall‎e t栈板‎t ox ma‎c hine自‎铆机wi‎r e EDM‎线割ED‎M放电机‎c oil s‎t ock卷料‎shee‎t stoc‎k片料t‎o leran‎c e工差‎s core=‎g roove‎压线ca‎m bloc‎k滑块p‎i lot导正‎筒tri‎m剪外边‎p ierce‎剪内边d‎r ag fo‎r m压锻差‎pocke‎t for ‎t he pu‎n ch he‎a d挂钩槽‎slug ‎h ole废料‎孔fea‎t ure d‎i e公母模‎expan‎s ion d‎w g展开图‎radiu‎s半径s‎h im(we‎d ge)楔子‎torc‎h-flam‎e cut火‎焰切割s‎e t scr‎e w止付螺丝‎form‎block‎折刀st‎o p pin‎定位销r‎o und p‎i erce ‎p unch=‎d ie bu‎t ton圆冲‎子sha‎p e pun‎c h=die‎inser‎t异形子‎s tock ‎l ocate‎r bloc‎k定位块‎u nder ‎c ut=sc‎r ap ch‎o pper清‎角act‎i ve pl‎a te活动板‎baff‎l e pla‎t e挡块‎c over ‎p late盖‎板mal‎e die公‎模fem‎a le di‎e母模g‎r oove ‎p unch压‎线冲子a‎i r-cus‎h ion e‎j ect-r‎o d气垫顶杆‎spri‎n g-box‎eject‎-plate‎弹簧箱顶板‎bushi‎n g blo‎c k衬套‎i nsert‎入块c‎l ub ca‎r高尔夫球车‎capa‎b ility‎能力pa‎r amete‎r参数f‎a ctor系‎数pho‎s phate‎皮膜化成‎v iscos‎i ty涂料粘‎度alk‎a lidip‎p ing脱脂‎main‎manif‎o ld主集流‎脉bez‎e l斜视规‎blank‎i ng穿落模‎deje‎c ting顶‎固模de‎m agnet‎i zatio‎n去磁;消磁‎high‎-speed‎trans‎m issio‎n高速传递‎heat ‎d issip‎a tion热‎传rac‎k上料d‎e greas‎e脱脂r‎i nse水洗‎alka‎l ine e‎t ch龄咬‎desmu‎t剥黑膜‎D.I. r‎i nse纯水‎次Chr‎o mate铬‎酸处理A‎n odize‎阳性处理‎s eal封孔‎revi‎s ion版次‎part‎numbe‎r/P/N料‎号goo‎d prod‎u cts良品‎scra‎p ed pr‎o ducts‎报放心品‎d efect‎i ve pr‎o ducts‎不良品f‎i nishe‎d prod‎u cts成品‎disp‎o sed p‎r oduct‎s处理品‎b arcod‎e条码f‎l ow ch‎a rt流程表‎单ass‎e mbly组‎装sta‎m ping冲‎压mol‎d ing成型‎spar‎e part‎s=buff‎e r备品‎c oordi‎n ate座标‎dism‎a ntle ‎t he di‎e折模a‎u xilia‎r y fuc‎t ion辅助‎功能po‎l y-lin‎e多义线‎h eater‎band ‎加热片t‎h ermoc‎o uple热‎电偶sa‎n d bla‎s ting喷‎沙gri‎t砂砾‎d erust‎i ng ma‎c hine除‎锈机de‎g ate打浇‎口dry‎e r烘干机‎induc‎t ion感应‎indu‎c tion ‎l ight感‎应光re‎s ponse‎=react‎i on=in‎t eract‎i on感应‎ram连杆‎edge‎finde‎r巡边器‎c oncav‎e凸co‎n vex凹‎short‎射料不足‎n ick缺口‎spec‎k瑕??‎s hine亮‎班spl‎a y 银纹‎gas m‎a rk焦痕‎delam‎i natio‎n起鳞c‎o ld sl‎u g冷块‎b lush ‎导色go‎u ge沟槽;‎凿槽sa‎t in te‎x ture段‎面咬花w‎i tness‎line证‎示线pa‎t ent专利‎grit‎沙砾gr‎a nule=‎p euet=‎g rain细‎粒gri‎t make‎r抽粒机‎c ushio‎n缓冲m‎a gnali‎u m镁铝合金‎magn‎e sium镁‎金met‎a l pla‎t e钣金‎l athe车‎mill‎锉pla‎n e刨g‎r ind磨‎drill‎铝bor‎i ng镗‎b linst‎e r气泡‎f illet‎镶;嵌边‎t hroug‎h-hole‎form通‎孔形式v‎o ller ‎p in fo‎r malit‎y滚针形式‎cam d‎r iver铡‎楔sha‎n k摸柄‎c rank ‎s haft曲‎柄轴au‎g ular ‎o ffset‎角度偏差‎v eloci‎t y速度‎p roduc‎t ion t‎e mpo生产‎进度现状‎t orque‎扭矩sp‎l ine=t‎h e mul‎t iple ‎k eys花键‎quen‎c hing淬‎火tem‎p ering‎回火an‎n ealin‎g退火c‎a rboni‎z ation‎碳化al‎l oy合金‎tungs‎t en hi‎g h spe‎e d ste‎e l钨高速的‎moly‎high ‎s peed ‎s teel钼‎高速的o‎r ganic‎solve‎n t有机溶剂‎brac‎k et小磁导‎liai‎s on联络单‎vola‎t ile挥发‎性res‎i stanc‎e电阻i‎o n离子‎t itrat‎o r滴定仪‎beaco‎n警示灯‎c oolan‎t冷却液‎c rushe‎r破碎机‎模具工程类‎plain‎die简易‎模pie‎r ce di‎e冲孔模‎f ormin‎g die成‎型模pr‎o gress‎i ve di‎e连续模‎g ang d‎i es复合模‎shea‎r ing d‎i e剪边模‎rivet‎i ng di‎e铆合模‎p ierce‎冲孔fo‎r ming成‎型(抽凸,冲‎凸)dr‎a w hol‎e抽孔b‎e nding‎折弯tr‎i m切边‎e mboss‎凸点do‎m e凸圆‎s emi-s‎h earin‎g半剪s‎t amp m‎a rk冲记号‎debu‎r r or ‎c oin压毛‎边pun‎c h riv‎e ting冲‎压铆合s‎i de st‎r etch侧‎冲压平r‎e el st‎r etch卷‎圆压平g‎r oove压‎线bla‎n king下‎料sta‎m p let‎t er冲字(‎料号)s‎h earin‎g剪断t‎i ck-ma‎r k nea‎r side正‎面压印t‎i ck-ma‎r k far‎s ide反面‎压印冲压‎名称类e‎x tensi‎o n dwg‎展开图p‎r ocedu‎r e dwg‎工程图d‎i e str‎u cture‎dwg模具‎结构图m‎a teria‎l材质m‎a teria‎l thic‎k ness料‎片厚度f‎a ctor系‎数upw‎a rd向上‎downw‎a rd向下‎press‎speci‎f icati‎o n冲床规格‎die ‎h eight‎range‎适用模高‎d ie he‎i ght闭模‎高度bu‎r r毛边‎g ap间隙‎weigh‎t重量t‎o tal w‎t.总重量‎punch‎wt.上模‎重量五金‎零件类i‎n ner g‎u iding‎post内‎导柱in‎n er he‎x agon ‎s crew内‎六角螺钉‎d owel ‎p in固定销‎coil‎sprin‎g弹簧l‎i fter ‎p in顶料销‎eq-h‎e ight ‎s leeve‎s=spoo‎l等高套筒‎pin销‎lifte‎r guid‎e pin浮‎升导料销‎g uide ‎p in导正销‎wire‎sprin‎g圆线弹簧‎outer‎guidi‎n g pos‎t外导柱‎s top s‎c rew止付‎螺丝lo‎c ated ‎p in定位销‎oute‎r bush‎外导套模‎板类to‎p plat‎e上托板（顶‎板）to‎p bloc‎k上垫脚‎p unch ‎s et上模座‎punc‎h pad上‎垫板pu‎n ch ho‎l der上夹‎板str‎i pper ‎p ad脱料背‎板up ‎s tripp‎e r上脱料板‎male‎die公模‎(凸模)‎f eatur‎e die公‎母模fe‎m ale d‎i e母模(凹‎模)up‎p er pl‎a te上模板‎lowe‎r plat‎e下模板‎d ie pa‎d下垫板‎d ie ho‎l der下夹‎板die‎set下模‎座bot‎t om bl‎o ck下垫脚‎bott‎o m pla‎t e下托板(‎底板)s‎t rippi‎n g pla‎t e内外打(‎脱料板)‎o uter ‎s tripp‎e r外脱料板‎inne‎r stri‎p per内脱‎料板lo‎w er st‎r ipper‎下脱料板‎零件类p‎u nch冲头‎inse‎r t入块(嵌‎入件)d‎e burri‎n g pun‎c h压毛边冲‎子gro‎o ve pu‎n ch压线冲‎子sta‎m ped p‎u nch字模‎冲子ro‎u nd pu‎n ch圆冲子‎spec‎i al sh‎a pe pu‎n ch异形冲‎子ben‎d ing b‎l ock折刀‎roll‎e r滚轴‎b affle‎plate‎挡块lo‎c ated ‎b lock定‎位块su‎p porti‎n g blo‎c k for‎locat‎i on定‎位支承块‎a ir cu‎s hion ‎p late气‎垫板ai‎r-cush‎i on ej‎e ct-ro‎d气垫顶杆‎trimm‎i ng pu‎n ch切边冲‎子sti‎f fenin‎g rib ‎p unch ‎= stin‎g er 加强‎筋冲子r‎i bbon ‎p unch压‎筋冲子r‎e el-st‎r etch ‎p unch卷‎圆压平冲子‎guide‎plate‎定位板s‎l iding‎block‎滑块sl‎i ding ‎d owel ‎b lock滑‎块固定块‎a ctive‎plate‎活动板l‎o wer s‎l iding‎plate‎下滑块板‎u pper ‎h older‎block‎上压块u‎p per m‎i d pla‎t e上中间板‎spri‎n g box‎弹簧箱s‎p ring-‎b ox ej‎e ct-ro‎d弹簧箱顶杆‎spri‎n g-box‎eject‎-plate‎弹簧箱顶板‎bushi‎n g bol‎c k衬套‎c over ‎p late盖‎板gui‎d e pad‎导料块塑‎件&模具相关‎英文co‎m pre s‎i on mo‎l ding压‎缩成型f‎l ash m‎o ld溢流式‎模具pl‎s itive‎mold挤‎压式模具‎s plit ‎m old分割‎式模具c‎a vity型‎控母模‎c ore模心‎公模t‎a per锥拔‎leat‎h er cl‎o ak仿皮革‎shiv‎e r饰纹‎f low m‎a rk流痕‎weldi‎n g mar‎k溶合痕‎p ost s‎c rew i‎n sert螺‎纹套筒埋值‎self ‎t appin‎g scre‎w自攻螺丝‎strip‎e r pla‎t e脱料板‎pisto‎n活塞c‎y linde‎r汽缸套‎c hip细碎‎物han‎d le mo‎l d手持式模‎具移转成‎型用模具‎e ncaps‎u latio‎n mold‎i ng低压封‎装成型射‎出成型用模具‎two ‎p late两‎极式（模具）‎well‎type蓄‎料井in‎s ulate‎d runn‎e r绝缘浇道‎方式ho‎t runn‎e r热浇道‎runne‎r plat‎浇道模块‎v alve ‎g ate阀门‎浇口ba‎n d hea‎t er环带状‎的电热器‎s pindl‎e阀针s‎p ear h‎e ad刨尖头‎slag‎well冷‎料井co‎l d sla‎g冷料渣‎a ir ve‎n t排气道‎h=0.0‎2~0.05‎m mw=‎3.2mm ‎L=3~5‎m mwe‎l ding ‎l ine熔合‎痕eje‎c t pin‎顶出针k‎n ock p‎i n顶出销‎retur‎n pin回‎位销反顶针‎sleav‎e套筒s‎t rippe‎r plat‎e脱料板‎i nsert‎core放‎置入子r‎u nner ‎s tripp‎e r pla‎t e浇道脱料‎板gui‎d e pin‎导销ej‎e ct ro‎d (bar‎)（成型机）‎顶业捧s‎u bzero‎深冷处理‎t hree ‎p late三‎极式模具‎r unner‎syste‎m浇道系统‎stres‎s crac‎k应力电裂‎orien‎t ation‎定向sp‎r ue ga‎t e射料浇口‎，直浇口‎n ozzle‎射嘴sp‎r ue lo‎c k pin‎料头钩销(拉‎料杆) s‎l ag we‎l l冷料井‎side ‎g ate侧浇‎口edg‎e gate‎侧缘浇口‎t ab ga‎t e搭接浇口‎film‎gate薄‎膜浇口f‎l ash g‎a te闸门浇‎口sli‎t gate‎缝隙浇口‎f an ga‎t e扇形浇口‎dish‎gate因‎盘形浇口‎H=F=1/‎2t~1/5‎tT=2‎.5~3.5‎m mdi‎a phrag‎m gate‎隔膜浇口‎r ing g‎a te环形浇‎口sub‎a rine ‎g ate潜入‎式浇口t‎u nnel ‎g ate隧道‎式浇口p‎i n gat‎e针点浇口‎Φ0.8~‎1.0mm ‎Runne‎r less‎无浇道(‎s prue ‎l ess)无‎射料管方式‎long ‎n ozzle‎延长喷嘴方式‎spru‎e浇口;溶渣‎品质人‎员名称类‎Q C qua‎l ity c‎o ntrol‎品质管理人‎员FQC‎final‎quali‎t y con‎t rol 终‎点品质管制人‎员IPQ‎C in p‎r ocess‎quali‎t y con‎t rol 制‎程中的品质管‎制人员O‎Q C out‎p ut qu‎a lity ‎c ontro‎l最终出货‎品质管制人员‎IQC ‎i ncomi‎n g qua‎l ity c‎o ntrol‎进料品质管‎制人员T‎Q C tot‎a l qua‎l ity c‎o ntrol‎全面质量管‎理POC‎passa‎g e qua‎l ity c‎o ntrol‎段检人员‎QA qu‎a lity ‎a ssura‎n ce 质量‎保证人员‎O QA ou‎t put q‎u ality‎assur‎a nce 出‎货质量保证人‎员QE ‎q ualit‎y engi‎n eerin‎g品质工程‎人员品质‎保证类F‎A I fir‎s t art‎i cle i‎n spect‎i on 新品‎首件检查‎F AA fi‎r st ar‎t icle ‎a ssura‎n ce 首件‎确认TV‎R tool‎verif‎i catio‎n repo‎r t 模具确‎认报告3‎B 3B 模‎具正式投产前‎确认CP‎capab‎i lity ‎i ndex ‎能力指数‎C PK ca‎p abili‎t y ind‎e x of ‎p roces‎s模具制程‎能力参数‎S SQA s‎t andar‎d ized ‎s uppli‎e r qua‎l ity 合‎格供应商品质‎评估OO‎B A out‎of bo‎x audi‎t开箱检查‎QFD ‎q ualit‎y func‎t ion d‎e ploym‎e nt 品质‎机能展开‎F MEA f‎a ilure‎model‎effec‎t ivene‎s s ana‎l ysis ‎失效模式分析‎8 di‎s cipli‎n es 8项‎回复内容‎F A fin‎a l aud‎i t 最後一‎次稽核C‎A R cor‎r ectiv‎e acti‎o n req‎u est 改‎正行动要求‎corre‎c tive ‎a ction‎repor‎t改正行动‎报告FQ‎C运作类‎A QL Ac‎c eptab‎l e Qua‎l ity L‎e vel 运‎作类允收品质‎水准S/‎S Samp‎l e siz‎e抽样检验‎样本大小‎A CC Ac‎c ept 允‎收REE‎Rejec‎t拒收‎C R Cri‎t ical ‎极严重的‎M AJ Ma‎j or 主要‎的MIN‎Minor‎轻微的‎A OQ A v‎e rage ‎O utput‎Quali‎t y 平均出‎厂品质A‎O QL A v‎e rage ‎O utput‎Quali‎t y Lev‎e l 平均出‎厂品质Q‎/R/S Q‎u ality‎/Relia‎b ility‎/Servi‎c e 品质/‎可靠度服务‎MIL-S‎T D Mil‎i tary-‎S tanda‎r d 军用标‎准S I‎-S IV ‎S pecia‎l I-Sp‎e cial ‎I V 特殊抽‎样水准等级‎P/N P‎a rt Nu‎m ber 料‎号L/N‎Lot N‎u mber ‎特采AO‎D Acce‎p t On ‎D eviat‎i on 特采‎UAI ‎U se As‎It 首件‎检查报告‎F PIR F‎i rst P‎i ece I‎n spect‎i on Re‎p ort 百‎万分之一‎P PM Pe‎r cent ‎P er Mi‎l lion ‎批号制程‎统计品管专类‎SPC ‎S tatis‎t ical ‎P roces‎s Cont‎r ol 统计‎制程管制‎S QC St‎a tisti‎c al Qu‎a lity ‎C ontro‎l统计品质‎管制R ‎R ange ‎全距AR‎A vera‎r y Ran‎g e 全距平‎均值UC‎L Uppe‎r Cent‎r al Li‎m it 管制‎上限LC‎L Lowe‎r Cent‎r al Li‎m it 管制‎下限MA‎X Maxi‎m um 最大‎值MIN‎Minim‎u m 最小值‎GRR ‎G auge ‎R eprod‎u cibil‎i ty&Re‎p eatab‎i lity ‎量具之再制性‎及重测性判断‎量可靠与否‎DIM D‎i mensi‎o n 尺寸‎DIA D‎i amete‎r直径‎F REQ F‎r equen‎c y 频率‎N Num‎b er 样品‎数其它品‎质术语类‎Q CC Qu‎a lity ‎C ontro‎l Circ‎l e 品质圈‎QIT ‎Q ualit‎y Impr‎o vemen‎t Team‎品质改善小‎组PDC‎A Plan‎Do Ch‎e ck Ac‎t ion 计‎划执行检‎查总结‎Z D Zer‎o Defe‎c t 零缺点‎QI Q‎u ality‎Impro‎v ement‎品质改善‎QP Qu‎a lity ‎P olicy‎目标方针‎TQM T‎o tal Q‎u ality‎Manag‎e ment ‎全面品质管理‎MRB ‎M ateri‎a l Rej‎e ct Bi‎l l 退货单‎LQL ‎L imiti‎n g Qua‎l ity L‎e vel 最‎低品质水准‎RMA R‎e turn ‎M ateri‎a l Aud‎i t 退料认‎可QAN‎Quali‎t y Ame‎l ionra‎t e Not‎i ce 品质‎改善活动‎A DM Ab‎s olute‎Dimen‎s ion M‎e asure‎m at 全尺‎寸测量Q‎T Qual‎i ty Ta‎r get 品‎质目标7‎Q CTool‎s 7 Qu‎a lity ‎C ontro‎l l Too‎l s 品管七‎大手法通‎用之件类‎E CN En‎g ineer‎i ng Ch‎a nge N‎o tes 工‎程变更通知(‎供应商)‎E CO En‎g ineer‎i ng Ch‎a nge O‎r der 工‎程改动要求(‎客户)P‎C N Pro‎c ess C‎h ange ‎N otice‎工序改动通‎知PMP‎Produ‎c t Man‎a gemen‎t Plan‎生产管制计‎划SIP‎Speci‎f icati‎o n In ‎P roces‎s制程检验‎规格SO‎P Stan‎d ard O‎p erati‎o n Pro‎c edure‎制造作业规‎范IS ‎I nspec‎t ion S‎p ecifi‎c ation‎成品检验规‎范BOM‎Bill ‎O f Mat‎e rial ‎物料清单‎P S Pac‎k age S‎p ecifi‎c ation‎包装规范‎SPEC ‎S pecif‎i catio‎n规格‎D WG Dr‎a wing ‎图面系统‎文件类Q‎C Qual‎i ty Sy‎s tem 品‎质系统E‎S Engi‎n eerin‎g Stan‎d ariza‎t ion 工‎程标准C‎G OO Ch‎i na Ge‎n eral ‎P CE龙华厂‎文件H ‎H uston‎(美国)休‎斯敦C ‎C ompaq‎(美国)康‎伯公司C‎China‎中国大陆‎A Ass‎e mbly ‎组装(厂) ‎S Sta‎m ping ‎冲压(厂) ‎P Pai‎n ting ‎烤漆(厂) ‎I Int‎e l 英特尔‎公司T ‎T AIWAN‎台湾I‎W S Int‎e rnati‎o nal W‎o rkman‎Stand‎a rd 工艺‎标准IS‎O Inte‎r natio‎n al St‎a ndard‎Organ‎i zatio‎n国际标准‎化组织G‎S Gene‎r al Sp‎e cific‎a tion ‎一般规格‎C MCS C‎-China‎M-Man‎u fact ‎C-Comp‎a q S-S‎t ampin‎g Comp‎a q产品在龙‎华冲压厂制造‎作业规范‎C QCA Q‎-Quali‎t y A-A‎s sembl‎y Comp‎a q产品在龙‎华组装厂品管‎作业规范‎C QCP P‎-Paint‎i ng Co‎m paq产品‎在龙华烤漆厂‎品管作业规范‎部类‎P MC Pr‎o ducti‎o n & M‎a teria‎l Cont‎r ol 生产‎和物料控制‎PPC P‎r oduct‎i on Pl‎a n Con‎t rol 生‎产计划控制‎MC Ma‎t erial‎Contr‎o l 物料控‎制ME ‎M anafa‎c ture ‎E ngine‎e ring ‎制造工程部‎PE Pr‎o ject ‎E ngine‎e ring ‎产品工程部‎A/C A‎c count‎a nt De‎p t 会计部‎P/A‎P erson‎a l & A‎d minis‎t ratio‎n人事行政‎部DC ‎D ocume‎n t Cen‎t er 资料‎中心QE‎Quali‎t y Eng‎i neeri‎n g 品质工‎程(部)‎Q A Qua‎l ity A‎s suran‎c e 品质保‎证(处)‎Q C Qua‎l ity C‎o ntrol‎品质管制(‎课)PD‎Produ‎c t Dep‎a rtmen‎t生产部‎LAB L‎a bratr‎y实验室‎IE In‎d ustri‎a l Eng‎i neeri‎n g 工业工‎程R&D‎Resea‎r ch & ‎D esign‎设计开发部‎P Pa‎i nting‎烤漆(厂)‎A As‎s sembl‎y组装(厂‎)S S‎t ampin‎g冲压(厂‎)生产类‎PCS ‎P ieces‎个(根,块‎等)PR‎S Pair‎s双(对等‎)CTN‎Carto‎n卡通箱‎PAL P‎a llet/‎s kid 栈‎板PO ‎P urcha‎s ing O‎r der 采‎购订单M‎O Manu‎f actur‎e Orde‎r生产单‎D/C D‎a te Co‎d e 生产日‎期码ID‎/C Ide‎n tific‎a tion ‎C ode (‎供应商)识别‎码SWR‎Speci‎a l Wor‎k Requ‎e st 特殊‎工作需求‎L/N Lo‎t Numb‎e r 批号‎P/N P‎a rt Nu‎m ber 料‎号其它‎OEM O‎r igina‎l Equi‎p ment ‎M anufa‎c ture ‎原设备制造‎PCE P‎e rsona‎l Comp‎u ter E‎n closu‎r e 个人电‎脑外设P‎C Pers‎o nal C‎o mpute‎r个人电脑‎CPU ‎C entra‎l Proc‎e ssing‎Unit ‎中央处理器‎SECC ‎S ECC` ‎电解片S‎G CC SG‎C C 热浸镀‎锌材料N‎H K Nor‎t h of ‎H ongko‎n g 中国大‎陆PRC‎Peopl‎e's Re‎p ublic‎of Ch‎i na 中国‎大陆U.‎S.A th‎e Unit‎e d Sta‎t es of‎Ameri‎c a 美国‎A.S.A‎.P As ‎S oon A‎s Poss‎i ble 尽‎可能快的‎E-MAIL‎Elect‎r ical-‎M ail 电‎子邮件N‎/A Not‎Appli‎c able ‎不适用Q‎T Y Qua‎n tity ‎数量VS‎以及R‎E V Rev‎i sion ‎版本JI‎T Just‎In Ti‎m e 零库存‎I/O ‎I nput/‎O utput‎输入/输出‎OK O‎k好N‎G Not ‎G ood 不‎行,不合格‎C=0 C‎r itica‎l=0 极严‎重不允许‎E SD El‎e ctry-‎s tatic‎Disch‎a rge 静‎电排放5‎S希腊语‎整理,整顿,‎清扫,清洁,‎教养A T‎I N Att‎e ntion‎知会C‎C Carb‎o n Cop‎y副本复印‎相关人员‎A PP Ap‎p rove ‎核准,认可,‎承认CH‎K Chec‎k确认‎A M Ant‎e Meri‎d ian 上‎午PM ‎P ost M‎e ridia‎n下午‎C D Com‎p act D‎i sk 光碟‎CD-R‎O M Com‎p act D‎i sk Re‎a d-Onl‎y Memo‎r y 只读光‎碟FDD‎Flopp‎y Disk‎Drive‎软碟机‎H DD Ha‎r d Dis‎k Driv‎e碟碟机‎REF R‎e feren‎c e 仅供参‎考CON‎N Conn‎e ctor ‎连接器C‎A V Cav‎i ty 模穴‎CAD ‎C omput‎e r Aid‎Desig‎n计算机辅‎助设计A‎S S'Y A‎s sembl‎y装配,组‎装MA T‎'S Mat‎e rial ‎材料IC‎Integ‎r ated ‎C ircui‎t集成电路‎T/P ‎T rue P‎o sitio‎n真位度‎TYP T‎y pe 类型‎WDR ‎W eekly‎Deliv‎e ry Re‎q uitem‎e nt 周出‎货需求C‎?T Cyc‎l e Tim‎e制程周期‎L/T ‎L ead T‎i me 前置‎时间(生产前‎准备时间) ‎S/T S‎t andar‎d Time‎标准时间‎P/M P‎r oduct‎Marke‎t产品市场‎3C C‎o mpute‎r,Comm‎u mcati‎o n,Con‎s umer ‎e lectr‎o nic's‎消费性电子‎5WIH‎When,‎W here,‎W ho,Wh‎a t,Why‎,How t‎o5M ‎M an,Ma‎c hine,‎M ateri‎a l,Met‎h od,Me‎a surem‎e nt4‎M IH Ma‎n,Mate‎r ia,Mo‎n ey,Me‎t hod,T‎i me 人力‎,物力,财务‎,技术,时间‎(资源) ‎S QA St‎r ategy‎Quali‎t y Ass‎u rance‎策略品质保‎证DQA‎Desig‎h Qual‎i ty As‎s uranc‎e设计品质‎保证MQ‎A Manu‎f actur‎e Qual‎i ty As‎s uranc‎e制造品质‎保证SS‎Q A Sal‎e s and‎servi‎c e Qua‎l ity A‎s suran‎c e 销售及‎服务品质保证‎LRR ‎L ot Re‎j eet R‎a te 批退‎率BS ‎B rain ‎s tormi‎n g 脑力激‎荡EMI‎Elect‎r onic ‎M agnet‎i on In‎s pect ‎高磁测试‎F MI Fr‎e quenc‎y Modu‎l atim ‎I nspec‎t高频测试‎B/M ‎B oar/M‎o lding‎(flat ‎c able)‎C/P ‎C onnec‎t or of‎PCA‎/P Ass‎e mbly ‎SPS S‎w itchi‎n g pow‎e r sup‎p ly 电源‎箱DT ‎D esk T‎o p 卧式(‎机箱)M‎T Mini‎-Tower‎立式(机箱‎)DVD‎Digit‎a l V ed‎i o Dis‎kVCD‎Vdeio‎Compa‎c t Dis‎kLCD‎Liqui‎d Crys‎t al Di‎s play ‎CAD C‎o mpute‎r AID ‎D esign‎CAM ‎C omput‎e r AID‎Manuf‎a cturi‎n gCA‎E Comp‎u ter A‎I D Eng‎i neeri‎n gAB‎I OS Ac‎h anced‎Basic‎in pu‎t/outp‎u t sys‎t em 先进‎的基本输入/‎输出系统‎C MOS C‎o mplem‎e ruary‎Metol‎l Oxid‎e Semi‎c onduc‎t or 互补‎金属氧化物半‎导体PD‎A Pers‎o nal D‎i gital‎Assis‎t ant 个‎人数字助理‎IC In‎t egrat‎e d Cir‎c uit 集‎成电路I‎S A Ind‎u stry ‎S tanda‎r d Arc‎h itect‎u re 工业‎标准体制结构‎MCA‎M icro ‎C hanne‎l Arch‎i tectu‎r e 微通道‎结构EI‎S A Ext‎e nded ‎I ndust‎r y Sta‎n dard ‎A rchit‎e cture‎扩充的工业‎标准结构‎S IMM S‎i ngle ‎i n-lin‎e memo‎r y mod‎u le 单项‎导通汇流组件‎DIMM‎Dual ‎i n-lin‎e Memo‎r y Mod‎u le 双项‎导通汇流组件‎LED ‎L ight-‎E mitti‎n g Dio‎d e 发光二‎级管FM‎E A Fai‎l ure M‎o de Ef‎f ectiv‎e nes 失‎效模式分析‎W/H W‎i re Ha‎r ness ‎金属线绪束集‎组件F/‎C Flat‎Calle‎排线P‎C B Pri‎n ted C‎i rcuit‎Board‎印刷电路板‎CAR ‎C orrec‎t ion A‎c tion ‎R eport‎改善报告‎NG No‎t Good‎不良。

常用工业英语词汇(个人整理资料)BOX 组件Plastic 塑胶cabinet 壳cover 上盖support 下盖top 上部bottom 底部cap (帽，杯) housing 壳insert(型，芯) Box 组件holder 支座roller 转子belt 皮带impeller风扇case 箱filter 滤网flex hose 软管metal 金属shaft 轴gear 齿轮washer 垫片die cast 铸件nut 螺母bush 轴套chuck 锁头screw 螺丝ring 垫圈spring 弹弓bit 铁嘴plate 片bar 杆spindle轴芯pin 小轴bearing 轴承thread 螺纹powder metal 粉末冶金key 锁匙pinion 小齿轮electric 电气件nameplate 铭牌cord 电线cable 电缆motor 电机switch 开关plug插头fuse 保险丝battery电池button 按钮cell电池adaptor 火牛socket插座P.C.B 电路板charger 充电座/器HI-POT高压测试timer定时器Power pack 电池组resistor电阻IC集成电路terms 术语toque 扭矩force 力speed 速度rating 额定值sampling 抽样fitting 装配futtonal 功能part line分型线aperance 外观testure 纹理vibration 振动finished 表面处理cavity 模腔model 型号part 零件assembly 部件accessory附件remark 注释mark 标记approve 认可defect 缺陷nonconformity 不合格comformity 合格sinkage 缩水burr 毛刺flash 披锋sharp edge 尖缘scratch刮花flow mark 流痕weld line 夹水纹rusty 铸跡hardness 硬度treatment 热处理cycle 循环freouency频数description名称inspection 检验check 检查dispose 处理injection注射revise 更改material 材料purchasing 采购gate 水口current 电流voltage电压power功率I.N.T接触不良rework 加工sort 拣货A.O.D 有偏差接收reject 退货Sketch 简图urgent 紧急Tolerance 公差fit配合Run-out跳动dimention 尺寸AQL 允收水准Packing 包装Label 标签sheet 纸Gift box 彩盒carton 箱Poly bag 塑料袋tape 带BMC 工具盒silk screen 丝印Card 卡片bar code 条形码Instruction manual 说明书M.O 订单B.O.M 物料清单R.O. 接收单I.R 检查报告Drill 电钻driver 电批vacuum cleaner 吸尘器Oven 烤炉trimmer 剪草机Instrument 仪器Gauge 量规pin gauge 芯棒Hole test 内径千分尺projector 投影仪Blocks 量块go-no go 通尺规Caliper 卡尺micpo meter 千分尺Dial indication 百分表miltimeter 万用表Calibration校正torque meter 扭力表QA 质量保证QC 质量控制PMC 物料控制R&D 工程研发PIE 生产工业工程P&A 人事SER 样本评估报告SDS来货检验资料ACCOUNTING 会计Accessory 附件Accounting 会计Actuate switch 启动开关Adapter 火牛Adhesive tape 胶粘带Adjustor调节器Agitator 搅拌器Air intel进气口Aluminum foil tape 铝箔带Anchor锚Appearance外观Approve认可Assembly装配Armature电枢/转子Ball holder铜珠套筒Bar棒Bar code 条形码Barbed connector 有倒扣的连接片Battery电池Battery cave电池底壳Battery cave cover电池盒/盖Battery tag电池片Bearing轴承Bearing-lock轴承-锁Belt皮带Bit铁嘴Bit guard防护罩Bit storage批嘴储存件Block量块Bottle connector瓶口连接Bottom底部Bottom cabinet-charger充电座底壳Box 箱Charger bracket充电座支架Bracket固定架/支架Brand label商标贴纸Bristle brush毛刷Bristle holder毛刷(柄)Brush roller 毛刷巻轴Bubble lever 水平珠Bucket箱Bulb reflector 电灯反射器Bulb support电灯泡支撑座Bundle捆/扎Burr毛刺Bush轴套Bushing-bearing lock轴套锁製Bushing-case adaptor轴套外套适配器Bush-output shaft带轴套的输出轴Button按钮Brush刷子/碳刷Cabinet壳Cabinet-cover面壳Cabinet-support底壳Cable电缆Cable clamp plate电线夹片Calibration校正Caliper卡尺Cam凸轮Cam plate偏心片Cap杯帽Carbon film resistor碳膜电阻Card卡片Carrying strip手带Carton箱Case箱Cavity模腔Cell电池Charger充电器Circuit ass’y循环装置Fasten-knob钮扣状旋钮Felt seal毛毡封Ferrite bead磁珠Fibre glass sleeve玻纤套Filler填空件Filter过滤器Filter bag bracker 过滤袋支架Filter frame过滤栏架Finished完成的First layer internal gear第一层内齿轮圈First layer sun gear第一层行星齿轮Fit配合Fitting装置Flash闪光Flex hose弯管Flow mark流痕Foam holder泡沫支架Force力Frequency频率Front cover cabinet 前面壳Front grill前脚架Front housing-gear box牙箱前壳Front support cabinet前底壳Function功能Fuse保险丝Fuse clip保险管夹Fuse P.C.B ass’y 保险丝底板组件Field 定子线圈Gasket 垫片/圈Gate水口Gauge量规Gear齿轮Gear box adaptor牙箱调整装置Gear housing cover牙箱盖Inverted retaining ring 反向保持介子Go-no go gauge通止规Gear box housing 牙箱壳Grease油脂Grease leak 漏油Handle catch手柄扣Handle grip手柄Hardness硬度Heat sink散热器Hex nut六角螺帽Hi-pot高压测试Holder支座Holder cover支座盖Hose elbow弯管Hose wrap plate软管扎带Housing壳Housing cover机壳上盖Housing handle机壳手柄Housing support机壳底座Idler gear-A变速齿轮“A”Idler gear-B变速齿轮“B”Idler shaftImpact drill(cap)冲击钻(杯)Impeller风扇叶Indicator cover指示器盖Indicator switch knob指示开关旋钮Injection注射Insert型芯/插入Insert refill bottle插入式替换瓶Inspection检验Instruction manual说明书Instrument仪器Insultator绝缘体Motor fixity-external马达外定位件Motor fixity-internal马达内定位件Key锁匙Key holder锁匙支架Label标签Lanyard手带Latch锁扣/门锁Led发光二极管Left head screw左牙螺丝Lens透镜Leveler accessory水平珠组件Leveler body水平珠本体Leveler cover水平珠盖Lever控制杆Lever oil水平珠油Lever-speed change调速杆Location spacer定位隔离器Louver天窗Lubricant润滑油Machine screw机器螺丝Mark 标记Massage ring按摩环Material材料Metal金属Metal washer ring 金属介子Micrometer千分尺Motor pulley 马达滑轮Model型号Motor accessory马达组件Motor bracket 马达支架Poly bag 塑料袋Project management项目管理Motor mounting马达定位Motor mounting bracket马达定位架Mounting plate杯片Multimeter 万用表Nameplate 铭牌Nonconformity不合格/不一致Nut 螺母o-ring 胶圈output shaft 轴芯，输出轴oven 烤炉p/p cover电池盒上座p/p support 电池盒底座packing包装part 零件part line 分型线pedestal台座，基座，垫座pin销pin gauge芯棒pinion小齿轮pinion-motor马达牙仔Pivot tube 转轴套plain washer-motor平面介子plant gear 行星齿轮plastic塑料plastic gear塑胶齿轮plastic tape胶纸plastic washer胶介子plate片plug插头run out摆动/跳动rusty生锈的powder metal粉末冶金power功率power pack电池组projector 投影仪Pulley flange 滑轮法兰pulley flange泵翼pump vane采购purchasing按钮push rod推杆PVC tubePVC sleeveRotor转子Ratchet 转轮Ratchet plate转轮片Rating额定值Rear cover cabinet后面盖Rear housing-gear box牙箱后壳Rear support cabinet后底盖Receptacle 插座Rectifier整流器Recycling label环保标签Reflector cap反光杯Reject退货Remark备注/注释Resistor电阻Reverse反向Revise更改Rework加工Ring垫圈Ring bolt有环螺钉Ring gear内齿轮圈Rocker switch摇杆开关Roller滚筒/辊子Rotary cap旋转杯Spring弹弓Spring clip弹性夹子Safety switch安全开关Sampling抽样Sander base磨沙机底座Scrap报废Scratch刮花Screw螺丝Screwdriver电批Screwdriver bit批嘴Second layer internal gear第二层内齿轮圈Second layer planet gear第二层行星齿轮Second layer run gear第二层恒星齿轮Secondary blower flangeSelf-tapping screw自攻螺丝Shaft轴芯Sharp edge锐边Sheet 纸/表格Shrinkable sleeve热缩管Silkscreen 丝印Sinkage缩水Sketch简图Sleeve套子Sliding rod滑动杆Socket (jack)插座Solution tank溶解槽Sort分类Spacer隔离件Speed速度Speed change knob变速钮Spindle轴芯Spindle gear-A转动齿轮“A”Spindle gear-B转动齿轮“B”Spine-ball刺珠Sponge海绵Spotter nozzle定心喷嘴Spring plate弹弓片Spring washer弹性介子Spring-torque control扭力控制弹簧Steel roller钢辊子Stopper-motor马达制动Stopper-right右制动Sun gear恒星/太阳齿轮Support下盖Support cabinet下壳Switch 开关Switch button (knob)开关按钮Switch lock锁掣Stator定子Tape带Tapping type攻牙形式Terminal接触片Terminal holder接触片支座Term术语/期间Thermal protector热保护器Thermal-fuse热感应保险丝Thermostat热敏开关Third layer internal gear第三层内齿轮圈Third layer planet gear第三层行星齿轮Third layer sun gear 第三层恒星齿轮Thread 螺纹Timer定时器Tolerance 公差Top cabinet-charger 充电座面壳Torque 扭矩Top上部Torque control knob 扭力调节器Torque meter扭力表Transformer变压器Heat treatment 热处理Grass trimmer剪草机Twisting screwdriver螺旋形电批UL approvel power cord UL认可的电线UL wire AWG 16 red UL16号红色电线UL wire AWG 16 black UL16号黑色电线Unit & accessory主机及附件Urgent紧急U-spring U型弹弓Vacuum cleaner真空吸尘器Variable speed switch变速开关Vibration振动V oltage电压W/o battery paper sleeve 无纸套电池Wall anchors挂墙胶条Washer垫片Washer ring-motor马达介子Washer-ball cover玻璃盖处的介子Washer-clutch扭力杯处的介子Washer-ring环形介子Zener diode齐纳二极管。

Lesson 1 Basic Concepts in Mechanics机械学的基本概念mechanics n.力学modify v.修改，调解，变更manageable a.可控制【管理】的incline v.（使）倾斜ramp n.斜板，斜坡【道】slope v.（使）倾斜friction n.摩擦roll v.滚动multiplier n.放大器，乘法器broom n.扫帚convert v.转变【化】handle n.手柄【把】sweep v.扫荡【描】，掠过efficiency n.效率gauge vt.测【计】量，校验bearing n.轴承ideal mechanical advantage 理想的机械效益neglect vt.忽略Lesson 2 Basic Assumption in Plasticity Theory 塑性理论的基本假设assumption n.假定plasticity n.塑性investigate v.调查，研究deformation n.变形metal forming process 金属成型工艺【过程】strain (rate) n.应变【速率】strength n.强度stress n.应力yield stress 屈服应力flow stress 流动应力tensile stress 拉【伸】应力compressive stress 压【缩】应力shear stress 剪【切】应力geometry n.几何形状elastic a.弹性的springback n.回弹bending n.弯曲，折弯precision forming 精密成型tolerance n.公差continuum n.连续（体）metallurgical a.冶金（学）的grain n.晶粒dislocation n.位错（uni-,tri-,multi-）axial a.（单，三，多）轴（向）的anisotropy n.各向异性cylindrical a.圆柱体的cross-section n.横截面platen n.（工作）台板，模板coincide with 一致，相符validity n.正确有效，合法with ease 轻（而）易（举）的，很容易的Lesson 3 Optimization for Finite Element Applications有限元优化的应用optimization n.优化，优选（法）finite element 有限元iterative a.反复的，迭代的alternative n.a.交替（的），可供选择的manual a.手动的，人工的trial-and-error 试凑法bias vt,n.（使）偏向【重、差】a desktop platform （计算机）桌面平台constrain(t) v,n.强制，约束response n.反【响】应，灵敏度parameter n.参数parametric a.参数的preprocess vt.预（先）加工，预处理mesh n,v.网格，啮合capability n.能力，性能，容量loop n.环，回路，循环pose v.提出model n.模型，样品displacement n.位移，排量，替换buckling n.弯【翘】曲，挠度factor n.因素gradient n.坡【梯】度，斜率flur n.【电，磁，热，光】通量，流量multidisciplinary a.多学科的deflection n.偏移【转，离】，挠曲Lesson 4 Metals 金属toughness n.韧性corrosion n.腐蚀dump v.倾倒，堆放recyle v.反复【循环】利用copper n.铜aluminum n.铝bronze n.青铜（器）alloy n.合金wear v.磨损metallic a.（含）金属（制）的specification n.操作规程，技术要求，说明书extract vt.提炼，萃取iron n.铁carbon n.碳ferrous a.（含）铁的ferrous metals 黑色金属lead n.铅zinc n.锌tin n.锡ore n.矿（石）mineral n,a.矿物（的）impurity n.杂质，不纯Lesson 5 Metallic and Nonmetallic Materials金属和非金属材料magnesium n.镁nickel n.镍brass n.黄铜luster n.光泽ductility n.延展性，可锻性it is likely that 很可能it is certain to (inf.)必然，一定density n.密度be distinguished from 与…区分coefficient n.系数in connection with 关于，与…相关【结合】category n.种类hardness n.硬度elasticity n.弹性beam n.横梁，一束（光）penetration n.贯穿，渗透abrasion n.磨损【耗】roll n,v.轧辊，滚，轧mill n.轧钢机，铣床spring n.弹簧permanent a.永久的rupture n.破【开】裂stamp n.冲压hammer n.（锻）锤Lesson 6 Plastics and Other Materials塑料和其他材料inorganic acid 无机酸sulphuric acid 硫酸hydrochloric acid 盐酸solvent n.溶剂carbon tetrachloride 四氯化碳rigid a,n.坚硬的，刚性（的），刚度mould(mold) n.模子，塑模，铸模decoration n.装饰fabricate vt.制造【备】，生产injection molding 注射模塑（法）blow molding 吹塑（法）compression molding 压塑（法），模压（法）extrusion n.挤压vacuum forming 真空模塑（法）powder metallurgy 粉末冶金constituent n,a.组成【的，部分】，组元simultaneously adv.同时subsequently adv.随后coherent a.互相凝聚的，协调一致的fusion n.熔化，熔接crystalline n,a.结晶【的】，晶体【的】restriction n.限制【定】，节流blend n,v.混合【物】，融合press n,v.压力机，压制homogeneous a.均匀的sinter n,vt.烧结【物】Lesson 7 Die Life and Die Failure模具的寿命和失效die n.模具，锻【冲】模，凹模die life 模具寿命die failure 模具损坏deterioration n.变坏，退化，损耗surface finish 表面光洁度breakdown n.破坏，击穿lubrication n.润滑cracking n.裂纹breakage n.断裂mode n.方式，状态，模式thermal fatigue 热疲劳layer n.层abrasive n,a.（研）磨料（的），磨损（的）impression n.模膛，型腔（槽）heat checking 热裂纹，龟裂steep n,a.陡（坡）的，急剧的reversal n.颠倒，相反overload n,v.（使）过【超】载initiation n.开【初】始，发【产】生discrete a.不连续的，单个的variable n.变量cavity n.模膛，型槽stock n.坯料，原材料impact n,v.冲击，碰撞Lesson 8 Cold Working and Hot Working 冷加工和热加工cold[hot] working 冷热加工forging n.锻造，锻件classification n.分类recrystallization n.再结晶take place 发生strain [deformation] hardening 应变【变形】硬化be referred to as 叫做，称为，被认为是warm working 温加工，温锻ultimate a,n.最终的，首要的，极限stress relieving 消除应力处理austenitic a.奥氏体的stainless steel 不锈钢annealing n.退火grain size 晶粒度solid solution 固溶体refinement n.精炼【制】，细化hazard n.危险，未知数，意外事件inherent a.固有的，先天的，本质的sensitive a.灵敏的，敏感的abnormal a.非正常的critical strain 临界应变Lesson 9 Casting 铸造casting n.铸造【件】die-casting n.模铸【件】foundry n.铸造【车间】pour v.浇注suitability n.适应性pig iron 生铁cupola n.冲天炉，化铁炉erosion n.腐蚀，（侵、烧）蚀ladle n.铁水包graphite n.石墨solidify v.（使）凝固disjoin v.拆散，分开ingot n.（钢）锭destructive a.破坏（性）的，有害的retard vt,n.（使）延缓，推迟solvent n,a.溶剂（的）copper-base alloy 铜基合金Lesson 10 Metal Forming Processes in Manufacturing 制造中的金属成形工艺machine-building 机械制造plastic working 塑性加工billet n 坯料，锻坯blank n.坯料，（冲压）板坯configuration n.外形，配置，排布stroke n.行程，冲程amortize v.阻尼，缓冲，分期偿还reliability n. 可靠性，安全性drawing n.（锻坯）拔长，【线，管材】拉拔deep drawing 深冲（压）brake forming 【压】折弯（机）成型stretch forming 张拉成型military n,a.军队【事，人】（的）consumer goods 消费品integrity n.完整性，完全（善）jet engine 喷气发动机turbine n.涡【汽】轮（机），透平（机）regarding 考虑到，关于Lesson 11 Forging锻造armor n.铠甲immortalize vt.（使）不朽（灭）blacksmith n.锻工mechanical press 机械压力机hydranlic press 液压机anvil n.（锤）砧，砧座craftsman n.技工handling n.处理，装卸，搬运flexibility n.柔（韧）性，灵活性drawn out 拔长upset n.镦粗，顶锻closed impression die 闭式模锻rapid-impact blow 快速冲击，猛打vertical a.立式的ram n.锤头，滑块，活动横梁block n.（模）块draft n.模锻斜度symmetrical a.轴对称的sizing n.整形，校正，定径drop forging 落锻，锤模锻impression die forging 模锻final forging 终锻overheat n.过热furnace n.【熔，高】炉pyrometer n.高温计Lesson 12 Benefits and Principles of Forging锻造的优点和工作原理metalworking n.金属压力加工knead v.揉搓【制】refine v.精炼【制】，细化porosity n.多孔性，疏松orient v.（使）定【取】向flow line 流线stress field 应力场manual skill 手工技巧at one’s command 自由使用，支配soundness n.致密性，坚固性，无缺陷attainable a.可达【得】到的open die forging 自由锻gross n.总共，重大confine vt. 限制，约束convert v.转变【换】，更换broken up 破【断】裂，分散microshrinkage n.显微缩孔elimination n.消除，淘汰align v.调整，对中，校直Lesson 13 Welding焊接weld(ing) v,n.焊接，熔焊pressurewelding 压力焊spotwelding 点焊buttwelding 对头（缝）焊fusionwelding 熔焊，熔接fiux-shielded arc welding 熔剂保护电弧焊diversity n.不同多样性fasten(ing) v,n.连接（件），紧固（件）shielding n.遮护，屏蔽solder(ing) v,n.软钎焊，（低温）焊料bismuth n.铋cadmium n.镉rivet n,v.铆钉，铆接braze n,vt.硬钎焊，铜焊oxidation n.氧化flux n.焊接，助溶剂squeeze v.挤压oxy-acetylene n,a.氧（乙）炔（的）torch n.焊炬electrode n.电（焊）极，焊条filler n.填充（剂）overlap v.搭接，重叠strike v.攻【打】击，放电Lesson 14 Heat Treatment热处理heat treatment 热处理microstructure n.显微组织low-carbon steel 低碳钢prescribe v.规定，指示microscopic a.显微的，微观的spheroidizing n.球化（处理）normalizing n.正火，（正）常化annealing n.退火hardening n.淬火tempering n.回火soaking(=holding) n.均热，保温retarding media 延缓介质prolonged a.长时间的，持续很久的critical temperature 临界温度globular a.球形（状）的carbide n.碳化物，硬质合金quenching n.淬火，骤冷removal n.除去，放出Lesson 15 Introduction to Mechanism机构介绍mechanism n.机械，机构，机构学kinematic a.=kinematical 运动的，运动学的kinematic chain 运动链link n.构件，杆件. v.连接【结】definite a.确定的constrained a.约束的，限定的unconstrained a.无约束的linkage n.连杆（组，机构）joint n.结【接】台，铰链. a.连接的，联合的pin n.销【钉】，铰销revolution v.旋转，转动. n.回转体prismatic a.棱柱（形）的nonlinear a.非线性的four-bar linkage 四杆机构kinematic chain 运动链prime mover 原动者【机】，驱动件coupler n.连接件，连杆pivot n.枢（轴），轴销，回转副，旋转中心configuration n.外形，构造，结构inversion n.转换，更换slider-crank mechanism 曲柄滑块机构multiloop n.多环链，a.多回路的sketch n.草【简，示意】图，v.画草图，草拟skeleton diagram 草图，示意图，简图envision v.想象binary a.二【双，复】的，二元的ternary a.三元的ternary links 三杆组quaternary a.四元的quaternary links 四杆组cam 凸轮cam follower n.凸轮从动件gear n.齿轮sprocket n.链轮belt n.【皮，布，钢】带pulley n.带轮spherical a.球的，球面的helical a.螺旋的three-dimensional 三维的，空间的intuitively adv.直觉【观】地synthesis n.合成（法），综合kinematician n.运动学研究者（家）innate a.先天的，固有的Lesson 16 Movement Analysis 运动分析criterion(pl.criteria) n.（判断）标准，判据，准则branch n,v.分（部，支）transmission angle 传动角rock n.摆动，v.摇动oscillate v.摆动，摇动parallelogram n.平行四边形antiparallelogram n.反平行四边形frame n.机架，构架impart v.给予，分给to impart M to N 把M给Ntorque n.力矩，扭矩dynamic a.=dynamical 动力的，动力学的inertia n.惯性（物），惯量static a.=statical 静力【学】的，静的index n.指数，指标friction n.摩擦thumb n.拇指，v.用拇指翻rule of thumb 根据经验和实际所得的做法matrix n.矩阵determinant n.行列式derivative n.导数derivative of M with respect to N M对于N的导数movability n.可动性，易动性parameter n.参数discount v.打折扣，忽视absolute a.绝对的graphical a.图形的，图解的polygon n.多边形theorem n.定理stress n.应力bearing n.轴承centripetal a.向心的Lesson 17 Kinematic Synthesis运动的综合packaging machinery 包装机械lubrication n.润滑specification n.技术要求actuation n.驱动jerk n.震动，冲击axis n.(pl.axes)轴【线，心】，中心线contour n.外形，轮廓线eccentricity n.偏心【度，率】gear ration 齿轮【速，齿数】比topologically adv.拓扑学地customary a.通常的，习惯的correlate v.使相关，使发生关系analog n.=analogue 类似（物），模拟linear analog 线性模拟second acceleration 二阶加速度higher acceleration 高阶加速度paraphrase v.释义，意译describe v.叙述，描述，作…运动category n.种类，类别deliberation n.慎重考虑province n.省，领域preconceive v.预想，事先想好analog computer 模拟计算机trace v.追踪，描画timing n.定时，计时，配时pitch v.投掷trajectory n.轨迹embed v.嵌入，夹在层间orientation n.（定）方位，（取）方向scoop n.勺子，铲斗，v.挖，掘，铲Lesson 18 Cams and Gears凸轮和齿轮cam n.凸轮gear n.齿轮curve n.曲线a.弯曲的groove n.槽，沟mate v.配合，啮合cylindrical a.圆柱的two-dimensional or planer 两维的或平面的three-dimensional or spatial 三维的或空间的normal n.法线a.垂直的complement n,a.余角，余的collinear a.共线的lateral a.横向的，侧向的stem n.杆guide n.导向件【器，装置】，导槽（座）intermittent a.间断的，不连续的dwell n,v.停止，小停顿inertial a.惯性的，惯量的engage v.啮合rack n.齿条noncircular a.非圆的conjugate a.共轭的，n.共轭值（线）cycloidal a.摆线的involved a.渐开线的，n.渐开线tolerance n.间隙，公差spur gear 直齿圆柱轮radial a.径向的，沿半径的offset n,vt.偏移，偏心a.偏心的disk cam 盘形凸轮tangent n.切线a.相切的，切线的concentric a.同圆（的），同心（的）camshaft n.凸轮轴pitch curve 节线herringbone a.人字形的intersect v.横穿，相交parallel helical gear斜齿轮，平行轴螺旋齿轮crossed helical gear 交错轴螺旋齿轮face gear 端面齿轮spiral bevel gear 螺旋齿圆锥齿轮worm n.蜗杆skew bevel 斜齿圆锥齿轮hypoid gear 准双曲面（直角交错轴双曲面）齿轮addendum (pl.addenda) n.齿顶，齿顶高project v.伸出，突出clearance n.间隙dedendum (pl. dedenda)n.齿根，齿根高tooth space 齿间距backlash n.间隙，齿隙Lesson 19 Screws, fasteners and joints螺纹件、紧固件和联接件screw n.螺钉，螺丝，v.旋紧，攻丝fastener n.紧固件joint n.连【联】接，接合bolt n.螺栓nut n.螺母cap screw 有头螺钉setscrew n.定位【固定，调整】螺钉rivet n.铆钉，v.用铆钉铆接key n.键weld n,v.焊接，熔焊braze n,v.钎焊，铜焊clip n.夹子，v.夹住，夹紧synonymous a.同意义的monotonous a.单调的taint n.污点，污染v.弄脏tough a.坚韧的ductile a.可延伸的，有延展性的，韧性的tighten v.上紧，拉紧twist v.扭转jumbo n.大型喷气式客机titanium n.钛close-tolerance 高精密度的tooling n.工具，刀具v.用刀具（切削）加工proliferate v.增殖，增殖assembly n.安装，装配，组件tap n.丝锥，v.攻螺丝stud n.双头螺栓resemble v.类似，像thread n.螺纹（线），v.车螺纹drill n,v.钻孔hexagon head 六角头fillister n.凹槽flat head 平头hexagon socket head 六角沉头disassemble v.拆开tensile a.拉【张】力的，受拉的shear n.剪切【力】v.剪切【断】harden v.使硬【化】washer n.垫圈preload n.预载荷fatigue n.疲劳micrometer n.千分尺，千分表elongation n.拉【伸】长modulus n.(pl.moduli)模数，模量wrench n.扳手dial n.刻度盘fractional a.分数的，小数的Lesson 21 Helical, Worm and Bevel Gears 斜齿轮、蜗杆蜗轮和锥齿轮helical gear 斜齿轮worm n.蜗杆，螺杆bevel gear 圆锥齿轮helix n,a.(pl. helices 或helixes)螺旋线，螺旋线的right hand 右手，右旋的helicoid n.a.螺旋【面，体】，螺旋（状，纹）的wrap v.缠绕unwind v.解开，展开generate v.产生，展成（加工）engagement n.啮合，接触diagonal n,a.对角线（的）objectionable a.该反对的，不能采用的spiral n,a. 螺旋线（的），卷线（的）spiral gear 螺旋齿轮mesh n.啮合worm gear 蜗轮pinion n.小齿轮pitch cylinder 节圆柱concave a.中凹的curvature a.曲率screw-like 像螺丝（杆）的thread n.线状物，螺纹线envelop v.包围，封闭enclose v.包围lead angle 导角cast v.铸造mill v.铣削outboard a,ad.外侧的，向外pronounced a.明确的，显著的stress n.应力tapered a.锥形的positively ad.确定地，强制（传动）地Pitch-line velocity 节线速度automobile differential 汽车差速器gearing n.齿轮传动（装置）offset n.偏置，横距hypoid a.准双曲面的hyperboloid n.双曲面，双曲面体Lesson 22 Shafts, Clutches and Brakes轴、离合器和制动器shaft n.轴clutch n.离合器brake n.制动器pulley n.（皮，胶）带轮flywheel n.飞轮sprocket n.链轮，星轮bending moment 弯曲力矩torsional a.扭转的static a.静（力，态）的axle n.心轴，轮轴spindle n.心轴，主轴deflection n.偏移，弯曲fillet n.圆角，倒角peening n.喷射（加工硬化法）shot peening 喷丸硬化stiff a.刚性的inertia n.惯性，惯量slippage n.滑动actuation n.驱动，开动coefficient n.系数statics n.静力学rim n.边缘，轮缘shoe n.闸瓦，制动片【块】band n.带，条cone n.圆锥miscellaneous a.（混）合的，杂项的assume v.假设，承担statical a.=static,静态的equilibrium n.平衡reaction n.反应，反力overload-release clutch 超载释放（保护）离合器magnetic fluid clutch 磁液离合器shift v.变换，（使）移动lever n.杆，（手）柄jaw n.颚板，夹爪ratchet n.棘轮circumferentiallyad v.周围地，圆周地mate v.配合，啮合，联接synchronous a.同步的linear drive 线性驱动装置clicking n.‘卡塔’声freewheel v.空转coupling n.联轴器sleeve n.套筒flat n.平面（部分）a.平的periphery n.圆周，周边wedge n.楔（形物）v.楔入pawl n.棘爪powder n.粉末mixture n.混合物electromagnetic a.电磁的coil n.线圈excitation n.刺激，激励shearing a.剪切的lockup n.锁住Lesson 41 Definition of Robotics and the Robot Systemmanipulator n.操作器，控制器，机械手peripheral a.周围的，外围的idiot n.白痴integrate v.使成为一体，使结合起来hard automation 刚性自动化a host of 许多Lesson 42 Basics of Computers(I)execute v.执行binary a.二进制的read only memory (ROM) 只读存储器random access memory (RAM)读写存储器，随机存储器erasable a.可擦去的volatile a.可丢失的Lesson 43 Basics of Computers(二)harsh a.恶劣的robust a.稳定的configuration n.结构，组态Morse Code 莫尔斯电码suffice v.足够interference n.干扰fluctuation n.脉动，波动expendable a.可消耗的intermediate a.中间的adaptor n.转换器transformer n.变压器rectifier n.整流器capacitor n.电容器Zener diode 齐纳（稳压）二极管buffer n.缓冲寄存器come across 碰到Baud rate 波特率Lesson 44 Programmable Controllersalbeit conj.虽然light-emitting diodes 发光二极管relay ladder logic 继电器梯形逻辑图archaically a.古体的，旧式的retention n.保留，保持versed a.熟练的，精通的fluidics n.射流sheer a.完全的，绝对的profligate a.浪费的proprietary a.专利的，专有的boolean expression 布尔表达式Lesson 45 CAD/CAMComputed-aided design(CAD) n.计算机辅助设计Computed-aided manufacturing(CAM) n.计算机辅助制造automatic factory n.自动化工厂drafting n.制图Computer-aided engineering n.计算机辅助工程management information systems n.管理信息系统graphics terminal n.图像终端a shared data base n.公用数据库three-dimensional a.三维的keyboard n.键盘lightpen=light pen n.光笔magnify v.放大flip v,n.翻转copy v.拷贝a mirror image 镜像symmetrical a.对称的artwork n.印刷线路原图Geometric modeling n.几何模型制造kinematics n.运动学Lesson 48 Flexible Manufacturing Systemsfexible manufacturing systems(FMS)柔性制造系统flexible manufacturing celles(FMC) 柔性制造单元automated guided vehicles 自动搬运小车conveyor n.传送装置pallet loading and unloading carts 上下料小车part program 零件程序data base 数据库data processing networks 数据处理网络inspection program 检测程序robot program 自动机程序real-time control data 实时控制数据the Control hierarchy 控制层次real-time fault recovery 实时故障恢复unmanned operation 无人化操作chip removel 排屑module n.模块，组件intelligent node智能节点。

Assembly line 组装线Layout 布置图Conveyer 流水线物料板Rivet table 拉钉机Rivet gun 拉钉枪Screw driver 起子Pneumatic screw driver 气动起子worktable 工作桌OOBA 开箱检查fit together 组装在一起fasten 锁紧(螺丝)fixture 夹具(治具)pallet 栈板barcode 条码barcode scanner 条码扫描器fuse together 熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME 制造工程师MT 制造生技cosmetic inspect 外观检查inner parts inspect 内部检查thumb screw 大头螺丝lbs. inch 镑、英寸EMI gasket 导电条front plate 前板rear plate 后板chassis 基座bezel panel 面板power button 电源按键reset button 重置键Hi-pot test of SPS 高源高压测试Voltage switch of SPS 电源电压接拉键sheet metal parts 冲件plastic parts 塑胶件SOP 制造作业程序material check list 物料检查表work cell 工作间trolley 台车carton 纸箱sub-line 支线left fork 叉车personnel resource department 人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer |plein|刨床miller铣床grinder磨床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vice section superisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |\\'skr?pid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |\\' ksi\\'dei?n|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单location地点present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheet PCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet 库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked 待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet 年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕??shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机。

动力输出装置POWER TAKE OFF燃油操作 FUEL CONTROL LINKAGE 减速踏板 DECELERATOR PEDAL 散热器 RADIATOR机油冷却器 OIL COOLER燃油箱 FUEL TANK燃油管路 FUEL PIPNG电气系统ELECTRICAL SYSTEM 工程机械常用英文词汇动力输出装置POWER TAKE OFF风扇及皮带FAN AND BELT吸油管总成INTAKE ASS’Y万向节UNIVERSAL JONT变距器外壳及调节阀TORQUE CONVERTER HOUSING AND REGULATOR VALVE 蜗轮轴及导轮TURBINE SHAFT AND STATOR液力变速箱TORQFLOW TRANSMISSION行星齿轮与轴PLANETARY GEAR AND SHAFT增速箱 TRANSFER CASE变速控制阀TRANSMISSION CONTROL VALVE盖与阀控制杆COVER AND VALVE调压阀PRESSURE REGULATOR VALVE变速杆GEARSHIFTLEVER变速锁定杆GEARSHIFT LOCK LEVEA变速箱油泵TRANSMISSIONPUMP变速箱机油滤清器TRANSMISSIONOIL FIL TER液力变距器管路系统TORQUE CONVERTER PIPLNG液力变速箱管路系统TORQFLOW TRANSMISSION PIPING三。

转向装置及最终传动STEERING SYSTEM AND FINAL DRIVE 后桥箱及大梁STEERING CASE AND MAIN FRAME机油器及油尺OIL FILLER AND LEVER GAUGE伞齿轮及轴BEVEL GEAR AND SHAFT转向离合器STEERING CLUTCH制动带和联动机构BRAKEBAND AND LINKAGE制动助力器及管路系统BRAKEBOOSTER AND PIPING转向控制杆STEERING CONTROL LEVER制动踏板BRAKE PEDAL制动连杆BRAKELINKAGE停车制动杆PARKING BRAKELEVER转向油泵STEERING PUMP机油过滤器OIL STRAINER转向机油过滤器STEERING OIL FIL TER转向控制阀STEERING CONTROL VALVE转向溢流阀MAIN RELIEF VALVE转向管路系统STEERING OIL PIPING最终传动箱FINAL DRIVE CASE四.台车台车架 TRACK ROLLER FRAME缓冲弹簧RECOIL SPRING台车架罩盖TRACK ROLLER FRAME COVER支重轮防护装置TRACK ROLLER GUARD引导轮FRONT IDLER支重轮TRACK ROLLER随动轮CARRIER ROLLER履带(主销型(标准型TRACK SHOE(MASTER PIN TYPE (STD 五.防护装置 GUARD散热器防护装置RADIATOR GUARD发动机护罩ENGINE HOOD翼板FENDER支撑架和后盖SUPPORTAND REAR COVER地板FLOOR PLATE下部防护罩BOTTOM GUARD驾驶座OPERATOR SEAT标牌与工具MARKS AND TOOLS平衡梁EQUALIZER BAR油缸支撑架CYLINDER STAY牵引装置DRAWBAR六。

工程机械英汉词典Engineering Machinery English-Chinese Dictionary1. Excavator - 挖掘机2. Bulldozer - 推土机3. Crane - 起重机4. Loader - 装载机5. Forklift - 叉车6. Dozer - 推土机7. Roller - 滚压机8. Grader - 平地机9. Paver - 铺路机10. Dump Truck - 自卸车11. Concrete Pump - 混凝土泵12. Mixer Truck - 搅拌车13. Drill Rig - 钻机14. Skid Steer Loader - 小型装载机15. Backhoe Loader - 装载机兼挖掘机16. Asphalt Paver - 沥青铺路机17. Road Roller - 道路压路机18. Tower Crane - 塔吊19. Mobile Crane - 移动式起重机20. Crawler Crane - 履带式起重机21. Wheel Loader - 轮式装载机22. Hydraulic Excavator - 液压挖掘机23. Telescopic Handler - 伸缩臂叉车24. Articulated Boom Lift - 叉车25. Aerial Work Platform - 空中作业平台26. Scissor Lift - 剪叉式吊篮27. Tractor - 拖拉机28. Skid Loader - 履带装载机29. Motor Grader - 自行式平地机30. Bulldozer - 推土机以上是一些常见的工程机械英汉词汇，希望对你有所帮助。

Assembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Pneumatic screw driver气动起子worktable 工作桌OOBA开箱检查fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet栈板barcode条码barcode scanner条码扫描器fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cosmetic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs. inch镑、英寸EMI gasket导电条front plate前板rear plate后板chassis 基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS 电源电压接拉键sheet metal parts 冲件plastic parts塑胶件SOP制造作业程序material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线left fork叉车production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer 'plein?刨床miller铣床grinder磨床driller铣床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager =vice manager副理section supervisor课长deputy section supervisor =vice section superisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped 'skr?pid报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation ' ksi'dei?n氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓name of a department部门名称administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单screwdriver holder起子插座pedal踩踏板stopper阻挡器flow board流水板hydraulic handjack油压板车forklift叉车pallet栈板glove(s)手套glove(s) with exposed fingers割手套thumb大拇指forefinger食指midfinger中指ring finger无名指little finger小指band-aid创可贴iudustrial alcohol工业酒精alcohol container沾湿台head of screwdriver起子头sweeper扫把mop拖把vaccum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋chain链条jack升降机production line流水线chain链条槽magnetizer加磁器lamp holder灯架to mop the floor拖地to clean the floor扫地to clean a table擦桌子air pipe 气管packaging tool打包机packaging打包missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a little bigger尺寸偏大(小)cosmetic defect外观不良slipped screwhead/slippery screw head螺丝滑头slipped screwhead/shippery screw thread 滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色scratch划伤poor processing 制程不良poor incoming part事件不良fold of pakaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍polishing/surface processing表面处理exposed metal/bare metal金属裸露lack of painting烤漆不到位safety安全quality品质delivery deadline交货期cost成本engineering工程die repair模修enterprise plan = enterprise expansion projects企划QC品管die worker模工production, to produce生产equipment设备to start a press开机stop/switch off a press关机classification整理regulation整顿cleanness清扫conservation清洁culture教养qualified products, up-to-grade products良品defective products, not up-to-grade products不良品waste废料board看板feeder送料机sliding rack滑料架defective product box不良品箱die change 换模to fix a die装模to take apart a die拆模to repair a die修模packing material包材basket蝴蝶竺plastic basket胶筐isolating plate baffle plate; barricade隔板carton box纸箱to pull and stretch拉深to put material in place, to cut material, to input落料to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料transportation运输(be)qualfied, up to grade合格not up to grade, not qualified不合格material change, stock change材料变更feature change 特性变更evaluation评估prepare for, make preparations for 准备parameters参数rotating speed, revolution转速manufacture management制造管理abnormal handling异常处理production unit生产单位lots of production生产批量steel plate钢板roll material卷料manufacture procedure制程operation procedure作业流程to revise, modify修订to switch over to, switch---to throw--over switching over切换engineering, project difficulty工程瓶颈stage die工程模automation自动化to stake, staking, reviting铆合add lubricating oil加润滑油shut die架模shut height of a die架模高度analog-mode device类模器die lifter举模器argon welding氩焊vocabulary for stamping冲压常词汇stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, block stop 定位块reset复位smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货to return delivenry to.to send delinery backto retrn of goods退货registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收to notice通知application form for purchase请购单consume, consumption消耗to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked 断裂to lubricate润滑common vocabulary for die engineering 模具工程常用词汇die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die连续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder文件夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备waste materials废料work in progress product在制品casing = containerazation装箱quantity of physical invetory second count 复盘点数量quantity of customs count会计师盘,点数量the first page第一联filed by accounting department for reference会计部存查end-user/using unit(department)使用单位summary of year-end physical inventory bills年终盘点截止单据汇总表bill name单据名称This sheet and physical inventory list will be sent to accountingdepartment together (Those of NHK will be sent to financialdepartment)本表请与盘点清册一起送会计部－(NHK 厂区送财会部)Application status records of year-end physical inventory List andphysical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO.空白与作废单号plate电镀mold成型material for engineering mold testing工程试模材料not included in physical inventory不列入盘点sample样品incoming material to be inspected进货待验description品名steel/rolled steel钢材material statistics sheet物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点chairman主席present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheet PCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory differenceanalysis sheet年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕?? shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸) draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件) deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相关英文compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具移转成型用模具encapsulation molding低压封装成型射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道h=0.02~0.05mmw=3.2mmL=3~5mmwelding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆) slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口H=F=1/2t~1/5tT=2.5~3.5mmdiaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Φ0.8~1.0mmRunner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣品质人员名称类QC quality control 品质管理人员FQC final quality control 终点品质管制人员IPQC in process quality control 制程中的品质管制人员OQC output quality control 最终出货品质管制人员IQC incoming quality control 进料品质管制人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance 出货质量保证人员QE quality engineering 品质工程人员品质保证类FAI first article inspection 新品首件检查FAA first article assurance 首件确认TVR tool verification report 模具确认报告3B 3B 模具正式投产前确认CP capability index 能力指数CPK capability index of process 模具制程能力参数SSQA standardized supplier quality 合格供应商品质评估OOBA out of box audit 开箱检查QFD quality function deployment 品质机能展开FMEA failure model effectiveness analysis 失效模式分析8 disciplines 8项回复内容FA final audit 最後一次稽核CAR corrective action request 改正行动要求corrective action report 改正行动报告FQC运作类AQL Acceptable Quality Level 运作类允收品质水准S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的AOQ Average Output Quality 平均出厂品质AOQL Average Output Quality Level 平均出厂品质Q/R/S Quality/Reliability/Service 品质/可靠度服务MIL-STD Military-Standard 军用标准S I-S IV Special I-Special IV 特殊抽样水准等级P/N Part Number 料号L/N Lot Number 特采AOD Accept On Deviation 特采UAI Use As It 首件检查报告FPIR First Piece Inspection Report 百万分之一PPM Percent Per Million 批号制程统计品管专类SPC Statistical Process Control 统计制程管制SQC Statistical Quality Control 统计品质管制R Range 全距AR Averary Range 全距平均值UCL Upper Central Limit 管制上限LCL Lower Central Limit 管制下限MAX Maximum 最大值MIN Minimum 最小值GRR Gauge Reproducibility&Repeatability 量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径FREQ Frequency 频率N Number 样品数其它品质术语类QCC Quality Control Circle 品质圈QIT Quality Improvement Team 品质改善小组PDCA Plan Do Check Action 计划执行检查总结ZD Zero Defect 零缺点QI Quality Improvement 品质改善QP Quality Policy 目标方针TQM Total Quality Management 全面品质管理MRB Material Reject Bill 退货单LQL Limiting Quality Level 最低品质水准RMA Return Material Audit 退料认可QAN Quality Amelionrate Notice 品质改善活动ADM Absolute Dimension Measuremat 全尺寸测量QT Quality Target 品质目标7QCTools 7 Quality Controll Tools 品管七大手法通用之件类ECN Engineering Change Notes 工程变更通知(供应商)ECO Engineering Change Order 工程改动要求(客户)PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Specification In Process 制程检验规格SOP Standard Operation Procedure 制造作业规范IS Inspection Specification 成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类QC Quality System 品质系统ES Engineering Standarization 工程标准CGOO China General PCE龙华厂文件H Huston (美国)休斯敦C Compaq (美国)康伯公司C China 中国大陆A Assembly 组装(厂)S Stamping 冲压(厂)P Painting 烤漆(厂) I Intel 英特尔公司T TAIWAN 台湾IWS International Workman Standard 工艺标准ISO International Standard Organization 国际标准化组织GS General Specification 一般规格CMCS C-China M-Manufact C-Compaq S-Stamping Compaq产品在龙华冲压厂制造作业规范CQCA Q-Quality A-Assembly Compaq产品在龙华组装厂品管作业规范CQCP P-Painting Compaq产品在龙华烤漆厂品管作业规范部类PMC Production & Material Control 生产和物料控制PPC Production Plan Control 生产计划控制MC Material Control 物料控制ME Manafacture Engineering 制造工程部PE Project Engineering 产品工程部A/C Accountant Dept 会计部P/A Personal & Administration 人事行政部DC Document Center 资料中心QE Quality Engineering 品质工程(部)QA Quality Assurance 品质保证(处)QC Quality Control 品质管制(课)PD Product Department 生产部LAB Labratry 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部P Painting 烤漆(厂)A Asssembly 组装(厂)S Stamping 冲压(厂)生产类PCS Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供应商)识别码SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号其它OEM Original Equipment Manufacture 原设备制造PCE Personal Computer Enclosure 个人电脑外设PC Personal Computer 个人电脑CPU Central Processing Unit 中央处理器SECC SECC` 电解片SGCC SGCC 热浸镀锌材料NHK North of Hongkong 中国大陆PRC People's Republic of China 中国大陆U.S.A the United States of America 美国A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量VS 以及REV Revision 版本JIT Just In Time 零库存I/O Input/Output 输入/输出OK Ok 好NG Not Good 不行,不合格C=0 Critical=0 极严重不允许ESD Electry-static Discharge 静电排放5S 希腊语整理,整顿,清扫,清洁,教养ATIN Attention 知会CC Carbon Copy 副本复印相关人员APP Approve 核准,认可,承认CHK Check 确认AM Ante Meridian 上午PM Post Meridian 下午CD Compact Disk 光碟CD-ROM Compact Disk Read-Only Memory 只读光碟FDD Floppy Disk Drive 软碟机HDD Hard Disk Drive 碟碟机REF Reference 仅供参考CONN Connector 连接器CAV Cavity 模穴CAD Computer Aid Design 计算机辅助设计ASS'Y Assembly 装配,组装MAT'S Material 材料IC Integrated Circuit 集成电路T/P True Position 真位度TYP Type 类型WDR Weekly Delivery Requitement 周出货需求C?T Cycle Time 制程周期L/T Lead Time 前置时间(生产前准备时间) S/T Standard Time 标准时间P/M Product Market 产品市场3C Computer,Commumcation,Consumer electronic's 消费性电子5WIH When,Where,Who,What,Why,How to 5MMan,Machine,Material,Method,Measurem ent4MIH Man,Materia,Money,Method,Time 人力,物力,财务,技术,时间(资源)SQA Strategy Quality Assurance 策略品质保证DQA Desigh Quality Assurance 设计品质保证MQA Manufacture Quality Assurance 制造品质保证SSQA Sales and service Quality Assurance 销售及服务品质保证LRR Lot Rejeet Rate 批退率BS Brain storming 脑力激荡EMI Electronic Magnetion Inspect 高磁测试FMI Frequency Modulatim Inspect 高频测试B/M Boar/Molding(flat cable)C/P Connector of PCA/P AssemblySPS Switching power supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital Vedio DiskVCD Vdeio Compact DiskLCD Liquid Crystal DisplayCAD Computer AID DesignCAM Computer AID ManufacturingCAE Computer AID EngineeringABIOS Achanced Basic in put/output system 先进的基本输入/输出系统CMOS Complemeruary Metoll Oxide Semiconductor 互补金属氧化物半导体PDA Personal Digital Assistant 个人数字助理IC Integrated Circuit 集成电路ISA Industry Standard Architecture 工业标准体制结构MCA Micro Channel Architecture 微通道结构EISA Extended Industry Standard Architecture 扩充的工业标准结构SIMM Single in-line memory module 单项导通汇流组件DIMM Dual in-line Memory Module 双项导通汇流组件LED Light-Emitting Diode 发光二级管FMEA Failure Mode Effectivenes 失效模式分析W/H Wire Harness 金属线绪束集组件F/C Flat Calle 排线PCB Printed Circuit Board 印刷电路板CAR Correction Action Report 改善报告NG Not Good 不良WPR Weekly Delivery Requirement 周出货要求PPM Parts Per Million 百万分之一TPM Total Production Maintenance 全面生产保养MRP Material Requiremcnt Planning 物料需计划OC Operation System 作业系统TBA To Be Design 待定,定缺D/C Drawing ChangeP/P Plans & ProceduneEMI Electrical-Music Industry 电子音乐工业RFI Read Frequency Input 读频输入MMC Maximum Material ConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material Size模具技术用语各种模具常用成形方式accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming ?泡成形sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模landed plunger mold 有肩柱塞式模具burnishing die 挤光模landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模ouvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 叠层模family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模模具厂常用之标准零配件air vent vale 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流档板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 托架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁) cavity retainer plate 模穴托板center pin 中心梢clamping block 锁定块coil spring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底die block 块形模体die body 铸模座die bush 合模衬套die button 冲模母模die clamper 夹模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲模板die set 冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘?flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧?goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶?冲头headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar 脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶?lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢locating ring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush 活动衬套making die 打印冲子manifold block 歧管档块master plate 靠模样板match plate 分型板mold base 塑胶模座mold clamp 铸模紧固夹mold platen 模用板moving bolster 换模保持装置moving bolster plate 可动侧模板one piece casting 整体铸件parallel block 平行垫块paring line 分模线parting lock set 合模定位器pass guide 穴型导板peened head punch 镶入式冲头pilot pin 导?pin gate 针尖浇口plate 衬板pre extrusion punch 顶挤冲头punch 冲头puncher 推杆pusher pin 衬套梢rack 机架rapping rod 起模杆re-entrant mold 凹入模retainer pin 嵌件梢retainer plate 托料板return pin 回位梢riding stripper 浮动脱模器ring gate 环型浇口roller 滚筒runner 流道runner ejector set 流道顶出器runner lock pin 流道拉梢screw plug 头塞set screw 固定螺丝shedder 脱模装置shim 分隔片shoe 模座之上下模板shoot 流道shoulder bolt 肩部螺丝skeleton 骨架slag riser 冒渣口slide(slide core) 滑块slip joint 滑配接头spacer block 间隔块spacer ring 间隔环spider 模蕊支架spindle 主轴sprue 注道sprue bushing 注道衬套sprue bushing guide 注道导套sprue lock bushing 注道定位衬套sprue puller 注道拉料?spue line 合模线square key 方键square nut 方螺帽square thread 方螺纹stop collar 限位套stop pin 止动梢stop ring 止动环stopper 定位停止梢straight pin 圆柱? stripper bolt 脱料螺栓stripper bushing 脱模衬套stripper plate 剥料板stroke end block 行程止梢submarine gate 潜入式浇口support pillar 支撑支柱/顶出支柱support pin 支撑梢supporting plate 托板sweep templete 造模刮板tab gate 辅助浇口taper key 推拔键taper pin 拔锥梢/锥形梢teeming 浇注three start screw 三条螺纹thrust pin 推力销tie bar 拉杵tunnel gate 隧道形浇口vent 通气孔wortle plate 拉丝模板模具常用之工作机械3D coordinate measurement 三次元量床boring machine 搪孔机cnc milling machine CNC铣床contouring machine 轮廓锯床copy grinding machine 仿形磨床copy lathe 仿形车床。

机械类各行业专业英语词汇1. 汽车行业 (Automotive Industry)•Engine（发动机）•Transmission（传动装置）•Suspension（悬挂系统）•Brake（刹车系统）•Steering（转向系统）•Exhaust system（排气系统）•Fuel injection（燃油喷射系统）•Tire（轮胎）•Battery（电池）•Alternator（发电机）2. 航空航天工业 (Aerospace Industry)•rcraft（飞机）•Wing（机翼）•Fuselage（机身）•Cockpit（驾驶舱）•Landing gear（起落架）•Jet engine（喷气发动机）•leron（副翼）•Thrust（推力）•Propeller（螺旋桨）•Avionics（航空电子设备）3. 重工业 (Heavy Industry)•Machinery（机械）•Crane（起重机）•Bulldozer（推土机）•Excavator（挖掘机）•Boiler（锅炉）•Conveyor belt（输送带）•Generator（发电机）•Drill（钻机）•Foundry（铸造厂）•Welding（焊接）4. 电子行业 (Electronics Industry)•Circuit board（电路板）•Microchip（微芯片）•Transistor（晶体管）•Capacitor（电容器）•Resistor（电阻器）•Diode（二极管）•Integrated circuit（集成电路）•Semiconductor（半导体）•Printed circuit board (PCB)（印刷电路板）•Soldering（焊接）5. 工程机械 (Construction Machinery)•Cranes（起重机）•Excavators（挖掘机）•Bulldozers（推土机）•Loaders（装载机）•Rollers（压路机）•Pavers（铺路机）•Concrete mixer（混凝土搅拌机）•Tower crane（塔式起重机）•Trencher（挖沟机）•Forklift（叉车）6. 机床行业 (Machine Tool Industry)•Lathe（车床）•Milling machine（铣床）•Drilling machine（钻床）•Grinding machine（磨床）•Boring machine（镗床）•Shaping machine（拉坯机）•CNC machine tool（数控机床）•Power press（压力机）•Shearing machine（剪板机）•Woodworking machine（木工机械）7. 包装机械 (Packaging Machinery)•Filling machine（灌装机）•Sealing machine（封口机）•Labeling machine（贴标机）•Capping machine（旋盖机）•Wrapping machine（包装机）•Coding machine（打码机）•Shrinking machine（收缩机）•Vacuum packaging machine（真空包装机）•Cartoning machine（装箱机）•Palletizing machine（托盘包装机）8. 纺织机械 (Textile Machinery)•Spinning machine（纺纱机）•Weaving machine（织布机）•Knitting machine（针织机）•Dyeing machine（染色机）•Printing machine（印花机）•Stenter machine（拉伸机）•Embroidery machine（绣花机）•Textile finishing machine（纺织整理机）•Yarn twisting machine（纱线捻接机）•Textile testing equipment（纺织测试设备）9. 精密仪器 (Precision Instruments)•Optical microscope（光学显微镜）•Electronic balance（电子天平）•Spectrophotometer（分光光度计）•Ultrasonic cleaner（超声波清洗机）•Atomic force microscope (AFM)（原子力显微镜）•Mass spectrometer（质谱仪）•X-ray diffractometer（X射线衍射仪）•Scanning electron microscope (SEM)（扫描电子显微镜）•Electron beam lithography (EBL)（电子束曝光机）•Surface profilometer（表面粗糙度仪）10. 医疗器械 (Medical Devices)•MRI machine（核磁共振机）•CT scanner（计算机断层扫描仪）•X-ray machine（X射线机）•Ultrasound machine（超声波仪）•Surgical microscope（手术显微镜）•Electrocardiogram (ECG) machine（心电图机）•Defibrillator（除颤仪）•Anesthesia machine（麻醉机）•Blood pressure monitor（血压监测仪）•Thermometer（体温计）以上是机械类各行业中常见的专业英语词汇。

（整理）工程机械技术词汇中英对照工程机械技术词汇术语中英对照挖掘机械Excavator 液压挖掘机Hydraulic excavator 履带式液压挖掘机Track hydraulic excavator轮胎式液压挖掘机Wheel hydraulic excavator机械式挖掘机Mechanicel excavator轮式挖掘机Bucket wheel excavator盾构挖掘机Shield boring machine 隧道掘进机Tunnel多斗挖沟机Multi-bucket treucher 挖掘装载机Sideshift backhre loader 步进式挖掘机Walking excavator 挖沟机Treucher 开沟铺管机Treucher/pipelayer铲土运输机械Earthe-moving machinery推土机Bulldozer 履带式推土机Track bulldozer轮胎式推土机Wheel bulldozer 湿地推土机Swamp bulldozer 沙漠推土机Desert bulldozer 推耙机Trimming dozer通井机Well dredger 铲运机Scraper自行式升运链板铲运机Elevator flight scraper拖式铲运机Tracion scraper平地机Motor grader 翻斗车Dump truck自卸卡车装载机Loader履带式装载机Track loader 轮胎式装载机Wheel loader滑移式装载机Skid steer loader 多功能装载机Universal loader 起重机械Crane 液压汽车起重机Hydraulic truck crane轮胎汽车起重机Wheel crane 履带起重机Track crane塔式起重机T ower crane 高空作业机械Aerial platform随车起重机On board lift 全地面汽车起重机All-torrain crane 卷扬机Specification 建筑升降机Lipting platform多功能作业车Multi-functional work horse 吊管机Pipelayer起重器、千斤顶Jacr 压实机械Compactor静碾压路机Static roller 振动压路机Vibratory roller振荡压路机Oscillate roller 夯土机Compactor混沌振动压路机Chaotic Vibratory voller手扶式振动压路机Walking-behind Vibratory V oller振捣器Vibratory compactor 轮胎压路机Pneumatic tired V oller 压实机Soil Compactor 垃圾填坦压实机Landfill Compactor 路面机械Road machinery 稳定土拌和机Soil stabilizer沥青混凝土拌和机Asphalt combined paver稳定土摊铺机沥青路面摊铺机Asphalt Paver 路面铣刨机Road planer沥青路面摊铺机Asphalt sprinkler滑模摊铺机Slipform paver 稀浆封层机沥青路面联合摊铺机Asphalt combined paver混凝土路面修筑机械Concrete pavement maintenance machinery公路养护车Road maintenance truck路面切碎机Road reclaimer沥青混凝土搅拌车Asphalt concrete mixer切缝机Slot cutler 桩工机械Pile dviver桩锤Hammer 桩架Derrick液压锤Hydraulic hammer空气柴油锤Air/Diesel hammer 钻孔机Drill水平钻机Horizontal drill 混凝土机械混凝土泵车Concrete-pump truck混凝土输送泵Concrete transit pump混凝土搅拌运输车Concrete mixing transit truck散装水泥输送车Bulk cement transit cal混凝土搅拌楼（站）Concrete mixing拖式混凝土泵车Stationary concrete pump钢筋和预应力机械钢筋调直切断机Steel bar rectifier/cutter钢筋弯曲机Steel bar binder钢筋加工机械Steel bar processing machine预应力机械Pre-stressing machine 凿岩机械Rock machinery 凿岩机Rock drill 凿岩台车Rock drill carrier 破碎机Crusher 叉车Lift truck隧道凿岩机器人Tunnel rock-drilling robot气动工具Pneumatic tools工业车辆Motorized industrial vehicle平衡重式叉车Counterbalance lift truck电瓶叉车Butlery fork lift内燃液力叉车Engine driven converter lift集装箱叉车Container fork lift 堆垛车Stacker越野叉车Off-road fork lift 圆木装卸叉Log fork lift板材装卸叉Lumber fork lift 市政机械Utility noachinery 环卫机械Environment Protection machinery园林机械Gardening machinery扫雪车Snow-moving vehicle.垃圾处理机械Carbage-processing machinery牵引车Tractor二.发动机型号Engine model 额定功率Rated horsepower进气方式Aspiration 气缸直径Cylinder bore活塞行程Piston stroke 燃油消耗率Fuel consumption rate 最大挖掘半径Max. digging reach 最大挖掘深度Max. digging olepth 最大挖掘高度Max. cutting height 最大卸载高度Max. dumping height 后部回转半径Rear-end swing radius最小离地间隙Min. ground clearance铲斗容量Bucket capacity 接地比压Ground pressure回转速度Swing speed 爬坡能力Gradeability行走速度Travel speed 整机工作质量Operating weight铲斗挖掘力Bucket digging force斗杆挖掘力Arm crowa force外形尺寸(长×宽×高) Overall dimensions推土机使用工作质量Operating weight 履带中心距Track guage 履带接地长度Lenght of track on ground前进速度Forward travel speed后退速度Reverse travel speed最大铲土深度Max. drop below ground最大松土深度Max. vipper digging depht铲刀提升高度Biade lift above ground松土器提升高度Ripper lift above ground铲土容量Dozing capacity工作效率Efficiency链轨节距Pitch铲刀(宽×高) Blade(width×height)铲运机牵引功率(拖式) Pulling power使用质量Operating weight铲土宽度Cuting width几何容量堆尖容量Hauling capacity铲土角Cutting angle切土深度Cutting depth装载机液力变矩器型式T orque converter type变速箱型式Transmission type 变速档位Gears主传动型式Main drive type 转向型式Steerin g type转向角度Steering angle 脚制动型式Foot brake type 手制动型式Hand brake type 最大牵引力Max. drqwbar pull 最大掘起力Max. breakout force 最大爬坡能力Max. grade ability 最大卸载高度Max. dumping clearance最小转弯半径Min tarning radius 动臂提升时间Raise time ofboom 动臂下降时间Lower time of boom 轮距Tread width 轴距Wheel base起重机械最大额定起重量Max. rated load 最大起重力矩Max. lifting moment 最大起升高度Max. lifting height 最大起升速度Max. lifting speed回转速度Slewing speed 最小转弯直径Min. turning diameter 最高行驶速度Max. traveling speed 接近角Approach angle 离去角Olepart angle 最小离地间隙Minimum gap支脚跨距Dimensions of outriggers 底盘型号Chassis model 主臂Main boom 主臂加副臂Boom and jib工作幅度Working radius 主臂仰角Main boom elerricking起升高度曲线Lifting performance chart压实机械工作质量Operating weight 前轮载荷Axle load front后轮载荷Axle load rear 静线压力Statc limear load front压实宽度Rolling width 转弯半径Turning radius inside轮胎规格Size of tyres 激振力Centrifugal force频率Frequency 振幅Amplityude行驶速度Speed range叉车额定起重量Rated capacity 载荷中心距Loading center起升高度Lifting height 货叉Fork prong门架倾斜Mast titlting 外侧转弯半径Outside steering radius 门悬距Forward overhang 起升速度Lifting speed净重Dead weight 蓄电池Battery supply最小离地间隙Min. ground clearance前轴负荷Load on front axle 后轴负荷Load on rear axle传动档数Number of gears 零部件液压件公称排量Displacement 额定压力Reted pressure最低转速Min speed 最大流量Max. flow rate允许背压Permitable back pressure公称通径Nominal diameter 调压范围Pressure adjustment运载阀压力Pressure on overload relief valve进油Inlet 出油Outlet轴伸型式Shaft end 推力Pushing force拉力Pulling force 缸径Bore杆径Rod diameter 速比Speed ratio标准行程Standard stroke 衬套销轴孔径Pin hole diameter 内密封Inside seals 外密封Outside seals泄漏量Leakage 过滤精度Filtering precision阻力Resistance基础件额定负荷Rated load 传动比Transmission ration安装距Installatin 最小轮钢尺寸Min. rim dimension 涡轮最大输出力矩Max. turbine output torque最大变矩比Stall torque ratio 直接安装Direct mounted分体安装Separate mounted 变速器速比Transmission ratio输出法兰Output flange 循环圆直径Cycle diameter循环流量Circulating flow 驱动油压Operating pressure驱动油量Required oil flow 最大张幅Max. opening width破碎力Max. crushing force 切断力Max. cutting force切刀长Cutter length 应力Stress张力Tension 冲程、行程Stroke轴向力、推力Thrust 压力Pressure重力Gravity 扭矩Moment发动机Engine 涡轮增压器Turbocharger电动机Electric 发电机Generator液压元件Hydrotatic power unit 液压泵Hydraulic pump压缩机Compressor 齿轮泵Gear pump柱塞泵Plunger pump 叶片泵控制阀Control valve 液压油缸Cylinder液压马达Hydraulic otor 蓄能器Accumulator液压软管Hose assembly 快换接头Ouick coupler液压油箱Hydraulic tank 变速器Power shift transmission 液力变矩器T orque converter 传动轴Driveaxle联轴节Coupler 转向器Steering轴承Bearing 制动器Brake离合器Clutch 差速器Differential车桥Axle 回转支承Swing bearing车轮Wheel 密封件Seal散热器Raclitor 空气滤清器Clnr却器Cooler 滤油器Hydraulic filter履带总成Track assembly 链轨总成Track link assmbly轨链节Track link 驱动轮Drive sprocket引导轮Front idier 支重轮Track roller万向节Universal socket 托链轮Carrier rolley张紧装置Track adjuster 履带板Track sloe终传动Final drive 平衡重Counterweight行走机构Undercarriage 动臂Boom斗杆Arm 铲斗Bucket斗齿Point tooth 松土器Ripper液压破碎锤Hydraulic impact hammer液压破碎钳Hydraulic impact clamp空调驾驶室Air-conditioned cabin防翻滚驾驶室Rops canopy 防重物驾驶室Fops canopy 悬挂系统Suspension 冷却系统Cooling system电器系统Electrical system 控制装置Control熨平板Screed 多功能熨平板Omniscreed 液压伸缩熨平装置Sereed hydraulic extension电子监控系统Electronic monitoring system 工作装置Front-end attachments。

这里汇聚了建筑和工程施工行业的大部分英语词汇和详细解说，如果要查询相关词汇，你可以点此word文档工具栏的“编辑”，找到“查找”，然后点开输入你要查询的词汇就可以查询了。

建筑学常用英语词汇：-frame A型骨架A-truss A型构架abrasion 磨耗；磨蚀abrasive cut-off machine 磨切机abrasive grinding machine 磨机(火石机)abrasive particle 磨粒absorption 吸收abutment 桥台；拱座abutting end 邻接端acceleration 加速acceleration lane 加速车道acceleration pedal 加速器踏板accelerator 催凝剂；加速器；催化剂acceptance criteria 接受准则access 通路；通道access door 检修门；通道门access lane 进出路径access panel 检修门access point 入口处；出入通道处access ramp 入口坡道；斜通道access road 通路；通道access shaft 竖井通道access spiral loop 螺旋式回旋通道access staircase 通道楼梯access step 上落踏板；出入踏板access tunnel 隧道通道accessible roof 可到达的屋顶；有通道的屋顶accessory 附件；配件accident 事故；意外accidental collapse 意外坍塌accommodate 装设；容纳accredited private laboratory 认可私营实验室accumulator 储压器；蓄电池accuracy limit 准确度极限acetylene cylinder 乙炔气(风煤)樽acid plant 酸洗设备；酸洗机acid pump 酸液泵acid tank 酸液缸acoustic couplant 声耦合剂acoustic coupler 声耦合器acoustic lining 隔音板acoustic screen 隔声屏acrylic paint 丙烯漆料acrylic sheet 丙烯胶片(阿加力胶片)active corrosion 活性腐蚀active earth pressure 主动土压力active oxidation 活性氧化actual plot ratio 实际地积比率actuator 促动器；唧筒；激发器adapt 改装adaptor 适配器；适配接头(万能苏)；转接器；接合器addition 增设；加建additional building works 增补建筑工程additional horizontal force 额外横向力additional plan 增补图则additional vent 加设通风口additive 添加剂adhesive 黏结剂；胶黏剂adhesive force 附力adit 入口；通路；坑道口adjacent construction 相邻建造物adjacent level 相邻水平adjacent site 相邻地盘adjacent street 相邻街道adjoining area 毗邻地区adjoining building 毗邻建筑物adjoining land 毗邻土地adjoining structure 毗邻构筑物adjustable 可调校adjuster 调节器adjustment 调校；调整admixture 掺合剂；外加剂advance directional sign 前置指路标志；方向预告标志advance earthworks 前期土方工程advance warning sign 前置警告标志advance works 前期工程aeration 灌气aeration tank 曝气池aerial 天线aerial rapid transit system 架空快速运输系统aerial ropeway 架空缆车系统aerial view 鸟瞰图aerofoil 翼型aerosol 悬浮微粒；喷雾affix 贴附aftercooler 后冷却器afterfilter 后过滤器agent 作用剂；代理人aggregate 骨料；集料；碎石aggregate area 总面积aggregate grading 骨料级配aggregate superficial area 表面总面积aggregate usable floor space 总实用楼面空间agitator 搅拌器；搅动机air bleeding 放气air blower 鼓风机air brake 气压制动器air circuit 空气回路air circuit breaker 空气断路器air cleaner 空气滤清器air compressor 空气压缩机air compressor governor 空气压缩机调压器air conditioning 空气调节air cooled chiller 风冷式冷冻机air cooler 空气冷却器air cooling system 空气冷却系统；风冷系统air coupling valve 空气联接阀air curtain fan 风帘风扇air cylinder 气缸；气筒air damper 风闸；气流调节器air distribution system 配气系统air distributor 空气分配器air dryer 空气干燥器air duct 通风管道；气槽air entrained cement 加气水泥；伴水泥air entraining agent 加气剂air exhaust 排气口air filter 空气滤器；风隔；隔尘网air filter chamber 空气过滤室air flowmeter 风量计；空气流量计air gap 气隙air grill 空气格栅air inlet 进风口；进气孔air inlet louver 进气百叶air inlet port 进气口air intake 进风口；进气孔；入气口air intake duct 进风槽air intake filter 进气过滤器air isolating cock 空气隔断旋塞air line breathing apparatus 气喉型呼吸器具air line strainer 进气管道隔滤器air outlet 出风口air outlet grille 空气出口栅格air particle 空气粒子air passage 风道air pipe/pipework 通气管；送气管air piston 空气活塞air pressure gauge 气压表air pressure switch 气压掣air pressurization system 空气加压系统air receiver 空气储存器air reservoir 储气缸air restrictor 空气节流器air shuttle valve 阻气阀air sprayer 喷涂器air spring 空气弹簧air strainer 空气隔滤器；空气滤网air supply outlet 供气出口air supply valve 供气阀air tank 空气箱air valve 进出气阀；放气阀air valve pit 进出气阀井；放气阀井air vent cock 通风管旋塞air ventilator 空气通风器air-operated damper 气动风闸airshaft 通风竖井airtight cover 气密盖airy dry varnish 风干清漆alarm 警报；警报器alarm bell 警钟alarm buzzer 警报器alga 水藻align 对准；调直；定线alignment (road) 路线；线向(特指道路中线的位置与方向) alignment plan (road) 路线平面图alkali-silica reaction 碱矽反应alkaline aggregate reaction 碱性集料反应alkaline pump 碱液泵alkaline tank 碱液缸alkalinity 碱度all-purpose road 混合车道；综合车道alley 巷allowable load 容许载重；容许荷载allowable stress 容许应力alloy 合金alloy steel bar 合金钢筋条alluvial deposit 冲积土层；冲积物alteration 更改；改建；改动alternating current (a.c.) 交流电alternative design 替代设计alternative route 替代路线alternator 交流发电机aluminium tape 铝带amber flashing light 黄色闪灯ambient pressure 周围压力ambient temperature 环境温度；周围温度amendment 修订amenities 市容建筑；设施；康乐设施amenity area 美化市容地带amenity railing 美观栏杆ammeter 电流表；安培计ampere (A) 安培(电流量单位)amplification 放大；增强amplitude 幅；振幅anchor 锚；锚竿支撑anchor bearing 锚承；锚座anchor bolt 锚栓anchor plate 锚碇板anchorage 锚碇；碇泊区；抛锚区；锚固anchorage length 锚固长度anchoring strength 锚固强度ancillary building 附属建筑物ancillary facilities 附属设施ancillary installation 附带装置ancillary works 附属工程angle cutter 角铁切割机angle iron bracket 角铁支架；角铁托架angle probe 斜探头angular velocity 角速度annunciation lamp 警示灯annunciator 传播器；呼唤器anode 阳极anode voltage 阳极电压antenna 天线anti-corrosion paint 防蚀漆anti-creep device 防溜装置anti-lift roller 防升滚轮anti-oxidizing paint 抗氧化漆anti-rust paint 防锈漆anti-skid chequer 防滑格纹anti-skid device 防滑装置anti-skid dressing 防滑钢沙anti-skid material 防滑物料anti-slip 防滑动；防空转；防打滑anti-static chain 抗静电链anti-static tyre 抗静电轮胎anti-stripping agent 防剥剂anti-syphonage pipe 反虹吸管anti-tip roller 防倾侧滚轮anti-vibration mounting 防震装置anti-vibration pad 防震垫anvil 铁砧aperture 隙缝；孔口apex 顶尖apparatus 仪器；装置；器具；器材appliance 用具；装置；设备applied covering 外加覆盖物applied load 外施荷载approach 进路；引道；接驳道路；引桥approach channel 进港航道；引渠approach ramp 引道坡approach road 引道；进路approach speed 来车速度approach taper 楔形引道路段approach viaduct 高架引道approved material 经批准的物料approved plan 经批准的图则appurtenance 附属物apron 跳板；护板；停机坪arc 电弧arc contact 电弧触点arc runner 电弧滚环arc welding 电弧焊接arch 拱；弓形；拱门architect 建筑师；则师architectural decoration 建筑装饰architectural projection 建筑上的伸出物area traffic control system 区域交通控制系统argon arc welding 氩气焊armature 电枢arrangement 排列；布置arresting assembly 止动装置arterial highway 干线道路arterial traffic 干线交通article of agreement 合约细则artificial lighting 人工照明as-built drawing 竣工图则as-constructed drawing 竣工图则asbestos abatement works 石棉拆除工程asbestos cement 石棉水泥asbestos gasket 石棉垫片ash pit 排渣槽；灰坑asphalt 沥青asphalt distributor 沥青喷洒机asphalt paver 沥青摊铺机asphalt roofing 沥青屋面asphaltic coating 沥青涂层asphaltic concrete 沥青混凝土aspirator 吸气器assemblage 组合物assembly 装置；组合assessment 评估associated works 相关工程；相关设施at-grade pedestrian crossing 地面行人过路处at-grade signal controlled junction 交通灯控制地面路口atmospheric distillation 常压蒸馏atmospheric pressure 大气压力；常压atmospheric temperature 常温atomization air fan 雾化空气风扇attachment 附件；附属物attenuation 衰减audible signal 音响讯号audible warning 音响警号authorities 权限authority 主管当局authorized officer 获授权人员authorized person 获授权人；认可人士；核准人士authorized works 获授权进行的工程；批准进行的工程automatic (spark) ignition device 自动(火花)点火装置automatic control switch 自动控制开关automatic operation 自动操作automatic release 自动脱扣automatic voltage regulator 自动调压器automatic weather station 自动气象站automation equipment 自动化设备auxiliary control panel 辅助掣板auxiliary equipment 辅助设备auxiliary feedwater pump 辅助给水泵auxiliary feedwater tank 辅助给水箱auxiliary plant 辅助厂房auxiliary system 辅助系统auxiliary water pump 辅助水泵average compressive stress 平均压应力average strength 平均强度axial fan 轴流式风扇axial force 轴向力axial load 轴向载重；轴向荷载axial stress 轴向应力axle bearing 车轴轴承(车轴啤令)A- frame A型骨架A-truss A型构架abrasion 磨耗；磨蚀abrasive cut-off machine 磨切机abrasive grinding machine 磨机(火石机)abrasive particle 磨粒absorption 吸收abutment 桥台；拱座abutting end 邻接端acceleration 加速acceleration lane 加速车道acceleration pedal 加速器踏板accelerator 催凝剂；加速器；催化剂acceptance criteria 接受准则access 通路；通道access door 检修门；通道门access lane 进出路径access panel 检修门access point 入口处；出入通道处access ramp 入口坡道；斜通道access road 通路；通道access shaft 竖井通道access spiral loop 螺旋式回旋通道access staircase 通道楼梯access step 上落踏板；出入踏板access tunnel 隧道通道accessible roof 可到达的屋顶；有通道的屋顶accessory 附件；配件accident 事故；意外accidental collapse 意外坍塌accommodate 装设；容纳accredited private laboratory 认可私营实验室accumulator 储压器；蓄电池accuracy limit 准确度极限acetylene cylinder 乙炔气(风煤)樽acid plant 酸洗设备；酸洗机acid pump 酸液泵acid tank 酸液缸acoustic couplant 声耦合剂acoustic coupler 声耦合器acoustic lining 隔音板acoustic screen 隔声屏acrylic paint 丙烯漆料acrylic sheet 丙烯胶片(阿加力胶片)active corrosion 活性腐蚀active earth pressure 主动土压力active oxidation 活性氧化actual plot ratio 实际地积比率actuator 促动器；唧筒；激发器adapt 改装adaptor 适配器；适配接头(万能苏)；转接器；接合器addition 增设；加建additional building works 增补建筑工程additional horizontal force 额外横向力additional plan 增补图则additional vent 加设通风口additive 添加剂adhesive 黏结剂；胶黏剂adhesive force 附力adit 入口；通路；坑道口adjacent construction 相邻建造物adjacent level 相邻水平adjacent site 相邻地盘adjacent street 相邻街道adjoining area 毗邻地区adjoining building 毗邻建筑物adjoining land 毗邻土地adjoining structure 毗邻构筑物adjustable 可调校adjuster 调节器adjustment 调校；调整admixture 掺合剂；外加剂advance directional sign 前置指路标志；方向预告标志advance earthworks 前期土方工程advance warning sign 前置警告标志advance works 前期工程aeration 灌气aeration tank 曝气池aerial 天线aerial rapid transit system 架空快速运输系统aerial ropeway 架空缆车系统aerial view 鸟瞰图aerofoil 翼型aerosol 悬浮微粒；喷雾affix 贴附aftercooler 后冷却器afterfilter 后过滤器agent 作用剂；代理人aggregate 骨料；集料；碎石aggregate area 总面积aggregate grading 骨料级配aggregate superficial area 表面总面积aggregate usable floor space 总实用楼面空间agitator 搅拌器；搅动机air bleeding 放气air blower 鼓风机air brake 气压制动器air circuit 空气回路air circuit breaker 空气断路器air cleaner 空气滤清器air compressor 空气压缩机air compressor governor 空气压缩机调压器air conditioning 空气调节air cooled chiller 风冷式冷冻机air cooler 空气冷却器air cooling system 空气冷却系统；风冷系统air coupling valve 空气联接阀air curtain fan 风帘风扇air cylinder 气缸；气筒air damper 风闸；气流调节器air distribution system 配气系统air distributor 空气分配器air dryer 空气干燥器air duct 通风管道；气槽air entrained cement 加气水泥；伴水泥air entraining agent 加气剂air exhaust 排气口air filter 空气滤器；风隔；隔尘网air filter chamber 空气过滤室air flowmeter 风量计；空气流量计air gap 气隙air grill 空气格栅air inlet 进风口；进气孔air inlet louver 进气百叶air inlet port 进气口air intake 进风口；进气孔；入气口air intake duct 进风槽air intake filter 进气过滤器air isolating cock 空气隔断旋塞air line breathing apparatus 气喉型呼吸器具air line strainer 进气管道隔滤器air outlet 出风口air outlet grille 空气出口栅格air particle 空气粒子air passage 风道air pipe/pipework 通气管；送气管air piston 空气活塞air pressure gauge 气压表air pressure switch 气压掣air pressurization system 空气加压系统air receiver 空气储存器air reservoir 储气缸air restrictor 空气节流器air shuttle valve 阻气阀air sprayer 喷涂器air spring 空气弹簧air strainer 空气隔滤器；空气滤网air supply outlet 供气出口air supply valve 供气阀air tank 空气箱air valve 进出气阀；放气阀air valve pit 进出气阀井；放气阀井air vent cock 通风管旋塞air ventilator 空气通风器air-operated damper 气动风闸airshaft 通风竖井airtight cover 气密盖airy dry varnish 风干清漆alarm 警报；警报器alarm bell 警钟alarm buzzer 警报器alga 水藻align 对准；调直；定线alignment (road) 路线；线向(特指道路中线的位置与方向) alignment plan (road) 路线平面图alkali-silica reaction 碱矽反应alkaline aggregate reaction 碱性集料反应alkaline pump 碱液泵alkaline tank 碱液缸alkalinity 碱度all-purpose road 混合车道；综合车道alley 巷allowable load 容许载重；容许荷载allowable stress 容许应力alloy 合金alloy steel bar 合金钢筋条alluvial deposit 冲积土层；冲积物alteration 更改；改建；改动alternating current (a.c.) 交流电alternative design 替代设计alternative route 替代路线alternator 交流发电机aluminium tape 铝带amber flashing light 黄色闪灯ambient pressure 周围压力ambient temperature 环境温度；周围温度amendment 修订amenities 市容建筑；设施；康乐设施amenity area 美化市容地带amenity railing 美观栏杆ammeter 电流表；安培计ampere (A) 安培(电流量单位) amplification 放大；增强amplitude 幅；振幅anchor 锚；锚竿支撑anchor bearing 锚承；锚座anchor bolt 锚栓anchor plate 锚碇板anchorage 锚碇；碇泊区；抛锚区；锚固anchorage length 锚固长度anchoring strength 锚固强度ancillary building 附属建筑物ancillary facilities 附属设施ancillary installation 附带装置ancillary works 附属工程angle cutter 角铁切割机angle iron bracket 角铁支架；角铁托架angle probe 斜探头angular velocity 角速度annunciation lamp 警示灯annunciator 传播器；呼唤器anode 阳极anode voltage 阳极电压antenna 天线anti-corrosion paint 防蚀漆anti-creep device 防溜装置anti-lift roller 防升滚轮anti-oxidizing paint 抗氧化漆anti-rust paint 防锈漆anti-skid chequer 防滑格纹anti-skid device 防滑装置anti-skid dressing 防滑钢沙anti-skid material 防滑物料anti-slip 防滑动；防空转；防打滑anti-static chain 抗静电链anti-static tyre 抗静电轮胎anti-stripping agent 防剥剂anti-syphonage pipe 反虹吸管anti-tip roller 防倾侧滚轮anti-vibration mounting 防震装置anti-vibration pad 防震垫anvil 铁砧aperture 隙缝；孔口apex 顶尖apparatus 仪器；装置；器具；器材appliance 用具；装置；设备applied covering 外加覆盖物applied load 外施荷载approach 进路；引道；接驳道路；引桥approach channel 进港航道；引渠approach ramp 引道坡approach road 引道；进路approach speed 来车速度approach taper 楔形引道路段approach viaduct 高架引道approved material 经批准的物料approved plan 经批准的图则appurtenance 附属物apron 跳板；护板；停机坪arc 电弧arc contact 电弧触点arc runner 电弧滚环arc welding 电弧焊接arch 拱；弓形；拱门architect 建筑师；则师architectural decoration 建筑装饰architectural projection 建筑上的伸出物area traffic control system 区域交通控制系统argon arc welding 氩气焊armature 电枢arrangement 排列；布置arresting assembly 止动装置arterial highway 干线道路arterial traffic 干线交通article of agreement 合约细则artificial lighting 人工照明as-built drawing 竣工图则as-constructed drawing 竣工图则asbestos abatement works 石棉拆除工程asbestos cement 石棉水泥asbestos gasket 石棉垫片ash pit 排渣槽；灰坑asphalt 沥青asphalt distributor 沥青喷洒机asphalt paver 沥青摊铺机asphalt roofing 沥青屋面asphaltic coating 沥青涂层asphaltic concrete 沥青混凝土aspirator 吸气器assemblage 组合物assembly 装置；组合assessment 评估associated works 相关工程；相关设施at-grade pedestrian crossing 地面行人过路处at-grade signal controlled junction 交通灯控制地面路口atmospheric distillation 常压蒸馏atmospheric pressure 大气压力；常压atmospheric temperature 常温atomization air fan 雾化空气风扇attachment 附件；附属物attenuation 衰减audible signal 音响讯号audible warning 音响警号authorities 权限authority 主管当局authorized officer 获授权人员authorized person 获授权人；认可人士；核准人士authorized works 获授权进行的工程；批准进行的工程automatic (spark) ignition device 自动(火花)点火装置automatic control switch 自动控制开关automatic operation 自动操作automatic release 自动脱扣automatic voltage regulator 自动调压器automatic weather station 自动气象站automation equipment 自动化设备auxiliary control panel 辅助掣板auxiliary equipment 辅助设备auxiliary feedwater pump 辅助给水泵auxiliary feedwater tank 辅助给水箱auxiliary plant 辅助厂房auxiliary system 辅助系统auxiliary water pump 辅助水泵average compressive stress 平均压应力average strength 平均强度axial fan 轴流式风扇axial force 轴向力axial load 轴向载重；轴向荷载axial stress 轴向应力axle bearing 车轴轴承(车轴啤令)back-fire 逆火back-up area 后勤地区；辅助埸地backfill 回填；回填土backfill material 回填物料background noise 本底噪声；背景噪声backing plate 垫板；背板baffle 隔板；挡板baffle plate 遮挡板baffle wall 遮挡墙balance tank 调节池；均衡槽balance weight 平衡锤balanced load 平衡载重balancer 平冲器balancing pipeline 平衡水管balcony 露台ball bearing 滚珠轴承ball valve 浮球阀；球形阀；波阀ball-and-socket joint 球窝接头ballast 道碴bamboo scaffolding 竹枝棚架band brake 带式制动器band clamp 带夹banshee alarm 尖啸警报bar 铁枝；杆；巴(压力量单位)bar tendon 钢筋barging area 驳运地点barrack 营房barrel 管筒；芯管barrette 方形桩barricade 路障；障碍物barrier 栏栅；护栏；障碍物；屏障barrier block 路障barrier gate 路闸barrier plate 阻挡板base 基座base course 路面下层；承重层；路基层base frame 基架base insulator 基架绝缘器base plate 底板；垫板base sealing 底部密封胶base slab 平底板base support 底座支架baseline 基线；底线；基准线baseline programme 基线计划basement 地库；地窖；地下室batching plant 混凝土混和机；配料厂batter pile 斜桩battery 蓄电池battery acid level 电池酸位battery cell volt 蓄电池电压battery charger 电池充电器battery electric locomotive 电力机车battery electrolyte 电池电解液battery-powered device 电池推动装置beacon 闪光指示灯bead 焊珠beam 横梁bearing 支座；支承；承座；轴承(啤令)；方向角bearing capacity 承载力bearing force 承重能力；承载能力bearing pad 支承垫片；承重垫片bearing pile 支承桩bearing pin 支承栓钉bearing plate 支承垫板bearing stress 支承应力bearing surface 支承面bedding 底层；层理bedplate 座板bedrock 基层岩behaviour 性能；状况Belisha beacon 斑马线灯；黄波灯bellow pot 气囊；气囊筒belt 带；皮带belt conveyor 带式输送机belt guard 皮带护罩belt tension 皮带拉力bend 弯角；弯位；路弯；弯管bending force 弯曲力bending stress 弯曲应力Benkelman beam test 贝克曼梁试验bentonite 膨润土；膨土岩berm channel 斜水平台渠berth 停泊处；碇泊位bevel 斜角；斜面bias 偏移bill of quantities 工料清单binder 黏合料bit 钻头bitumen 沥青bitumen coating 沥青外搪层；沥青外衬bitumen felt 沥青纸bitumen lining 沥青内搪层；沥青衬里bituminous concrete 沥青混凝土bituminous macadam 沥青碎石bituminous waterproof membrane 沥青防水膜blade 剪刀；叶片blank flange 盲板法兰；盲板凸缘；管口盖板blanking plate 封板blast-furnace 鼓风炉blast-furnace slag cement 炉渣水泥blasting 爆石；爆破bleed nipple 放气嘴；减压嘴bleed off pipe 溢流管bleed screw 放气螺钉；减压螺钉bleeding 泌浆(混凝土)；泌水性(混凝土) blended cement 混合水泥blending control 混合控制blinding 补路石砂；(填充表面孔隙的细石) block plan 楼宇平面图blow down 放水；放气blow down valve 放泄阀；排水阀blower 吹风机；鼓风机bobbin 绕线管bogie 转向架boiler room 锅炉房boiling point 沸点bollard 护柱；系船柱bollard light 安全岛指示灯bollard plinth 护柱柱基；护柱基座bolster 承枕；横撑bolt 螺栓bond 黏结；黏合；契约bond coat 黏合层bond strength 黏合强度bond stress 黏合应力boom 吊杆booster pump 增压泵booster pumping station 增压抽水站booster transformer 增压变压器booster water pump 增压水泵；增压抽水机borated water storage tank 含硼水贮存箱border link 边境连接道路border terminus 过境终站bore 钻孔；内孔bored pile 螺旋钻孔桩bored tunnel 钻挖的隧道borehole log 钻孔纪录boric acid 硼酸boring 钻探；冲孔boring machine 钻探机；镗床borrow area 采泥区；采料区bottleneck 樽颈；狭窄段bottom heave 底部隆bottom layer 底层bottom plate 底板boulder 巨砾boundary 分界线；界线box culvert 盒形排水渠；盒形暗渠；箱形暗渠；方形去水渠box girder 箱形大梁brace 撑杆；支撑braced structure 受横向支撑的结构bracing 支撑bracing structure 支撑结构bracket 托架；支架braid 编织电缆brake 制动器brake horse power 制动马力brake lining 制动器摩擦衬片brake pedal 刹车踏脚板brake system 制动系统brake test 制动器试验brake tester 制动系统测试器braking distance 制动距离；刹车距离branch circuit 分支电路branch pipe/pipework 支管；分支喉管brass gate valve 黄铜闸阀brass wire brush 铜丝刷break pressure tank 减压配水缸箱；水压调节池breaker 轧碎机；碎石机；隔断器；开关闸；断路器；保险掣breaking strength 抗断强度breakthrough 击穿breakwater 防波堤breather 通气孔；呼吸器breather valve 通气阀breathing apparatus 呼吸器具brick 砖brick works 砌砖工程brickwork 砖块bridge 桥梁bridge abutment 桥台bridge crane 桥式吊机bridge deck 桥面板；桥板；桥面bridge girder 桥大梁bridge pier 桥墩bridgeworks 桥梁工程bubble accumulator 气泡贮存器bucket conveyor 斗式输送机buckling 压曲；压弯buckling load 压曲临界荷载buffer 缓冲；缓冲器；减震器buffer area 缓冲地区build, operate and transfer (BOT) franchise 「建造、营运及移交」专营权builder's lift 施工用升降机building 楼宇；建筑物；大厦building area 建筑面积building condition 楼宇状况building construction 建筑物建造；建筑营造building design 建筑物设计；建筑设计building envelope 建筑物外壳building frontage 屋宇前面building land 屋地；屋宇建筑用地building material 建筑物料building plan 建筑图则building services 屋宇设备；屋宇装building site 屋宇建筑地盘；工地building works 屋宇建筑工程；楼宇建筑工程bulk excavation works 大型挖掘工程bulldozer 推土机；铲泥车bump (road) 限速路面突块bumper 缓冲器；防撞器；防撞杠bunch 捆扎bund ；田基；堤bund wall 墙bunded area 堤保护区buoyant force 浮力burglar alarm system 防盗警钟系统buried concrete 埋入地下的混凝土burner 燃烧器；炉头bursting 爆裂bus interchange 巴士转车处bus stop shelter 巴士站上盖bus terminus 巴士总站bus-bar 导电条；母线(巴士巴)bus-coupler 母线联接bush 轴衬(杯士)butt fusion welding 对头熔接butt welding 对焊butterfly cock 蝶形旋阀butterfly gate 蝶形闸butterfly valve 蝶形阀buttress 支墩buzzer 蜂音器；蜂鸣器by-pass 绕道；支路；支管；旁通管by-pass valve 旁通阀cab 小室；驾驶室cabinet 小室；贮存柜cable 电缆cable channel 电缆沟；电缆槽cable conduit 电缆管cable coupler 电缆耦合器cable draw pit 电缆沙井；铺缆井cable duct 电缆管道cable gland 电缆密封套cable joint 电缆接头cable laying wagon 电缆敷设车cable lead 电缆引线cable route 电缆路线cable supported viaduct 悬索高架桥cable suspension bridge 钢索吊桥cable trench 电缆槽cable trough 电缆坑cable trunk 电缆干线cable tunnel 电缆隧道cable-stayed bridge 斜拉桥cage 机厢caisson 沉箱caisson cap 沉箱盖caisson foundation 沉箱地基；沉箱基础caisson pier 沉箱墩caisson pile 沉箱桩caisson retaining wall 沉箱挡土墙caisson wall 沉箱墙calibration 校准caliper measure 测径calorie (cal) 卡路里(热量单位)calorific value 热值calorifier 加热器cam 突轮camber 拱度candela (cd) 烛光(发光强度单位) canister respirator 罐型防毒面具canopy 檐篷cantilever 悬臂cantilever beam 悬臂梁cantilever bridge 悬臂桥cantilever crane 悬臂吊机cantilever footing 悬臂基脚cantilever foundation 悬臂地基cantilever support 悬臂支架canvas 帆布canvas belt 帆布带cap 帽；盖capacitance meter 电容表capacitor 电容器capacity 容量；载客量capacity control valve 容量控制阀capital works 基本建设工程；基建工程；carbon brush 碳刷carbon pile 碳柱carbon ring 碳环carbon steel 含碳钢carbon strip 碳条carbonation 碳化carbonation depth 碳化深度carbonation process 碳化过程carborundum 金刚砂carburettor 化油器；气化器cargo handling area 货物装卸区carriageway 行车道carriageway marking 行车道标记carrying capacity 运载量；载重量；承载能力cartridge 子弹；弹药筒cartridge operated tool 弹药推动的工具cartridge type respirator 滤罐型呼吸器；筒型防毒面具（猪咀）casing 套管cast iron 铸铁；生铁cast iron conductor 铸铁导管cast iron pipe 铸铁管(生铁管)cast-in anchorage 浇注锚固cast-in-place 灌注；现场浇筑cast-in-situ concrete unit 现场浇筑混凝土构件casting basin 预制件工场casualty team 伤亡急救队cat ladder 便梯；爬梯catalytic action 催化作用catch 挡片；制止器；扣掣；门扣catch fan 扇形防护网架catch fence 拦截围墙catch platform 坠台catchment area 集水区；引集范围catchpit 排水井；集水坑；截流井catchwater channel 集水槽catenary wire 吊索cathode 阴极cathode ray tube 阴极射线管cathodic protection 阴极保护catwalk 跳板；轻便梯；轻便栈桥caulk 堵缝caulking material 填隙料causeway 堤道caution sign 警告标志cavern 洞穴cavity 中空部分；穴cavity wall 空心墙ceiling 天花板ceiling slab 天花板ceiling suspension hook 天花吊cell 电池cellular office 分格式办公室cement 水泥cement content 水泥含量cement mortar 水泥沙浆cement plaster 水泥灰泥cement rendering 水泥荡面cement sand mix 水泥沙浆cementitious content 水泥质成分centi (c) 厘(百分之一)central divider 中央分隔栏central dividing strip 中央分隔带central line 中线central median 中央分隔带central power-driven machine 中央动力机械central profile barrier 中央纵向护栏central reserve 中央预留带central span 中跨距centre lane 中行车线centre line 中心线centre line of street 街道中心线centrifugal filter 离心过滤器centrifugal force 离心力centrifugal load 离心荷载centrifugal pump 离心泵centripetal force 向心力ceramic tile 瓷砖certificate 证明书certificate of inspection 检查证明书certificate of registration 注册证明书；登记证明书certification 核证certified copy 经核证文本certify 核证cesspool 污水池chain 链chain block 滑车吊链；链动滑轮(尖箔落) chainage 丈量长度；里程距离chainlink fence 扣环围栏；铁网围栏chamber 小室；间隔chamfer 去角(斜角)位；斜削change-over switch 转换开关change-over valve 转换阀channel 沟渠；线糟；槽；渠道；频道channel cover 槽盖channelization (traffic) (交通)导流channelizing island 导行岛channelizing line 导行线characteristic strength 特征强度chart datum 海图基准面chart recorder 图表记录器chasis 车身底盘check 查核check block 挡块check joint 止回接头check mechanism 制动装置check plate 垫板；挡板check rail 护轮轨check screw 止动螺钉check valve 止回流阀chemical action 化学作用chemical dosing 化学剂量chemical grout 化学灌浆chemical property 化学特性chemical refuse 化学垃圾chemical test 化学测试chemicals 化学品chequered plate 网纹板chill plate 冷却板chilled air fan 冷风风扇chilled water pump 冷冻水泵chiller 冷冻机chiller plant 致冷设备；制冷设备chimney 烟沟；烟chimney coping 烟囱盖顶chimney stack 烟囱chippings 碎屑；破片chisel 凿chloride 氯化物chloride content 氯化物含量chloride diffusion 氯化物扩散chloride extraction 除氯chloride ion 氯离子chloride ion content 氯离子含量chlorinated polyvinyl chloride (PVC-C) 氯化聚氯乙烯chlorinated water 加有氯气的水chlorinator 加氯器chopper 斩波器chunam 灰泥土批荡chute 溜槽；滑道chute 槽管circuit 电路；环道circuit breaker 断路保险掣circular footing 圆基脚circular road 环回道路circulating water pump 循环水泵circulation mode 循环模式circumferential road 环回道路civil works 土木工程cladding 骨架外墙；覆盖层claim 声称；申索；索偿clamp 夹钳claplock cable clamp 拍扣式电缆线夹clay 黏土clay field pipe 瓦管cleaning eye 清理孔cleaning rod 清理棒cleansing 洁净clear effective length 净有效长度clear height 净高clear opening 净开口clear space 净空间clear span 净跨距clear width 净阔度clearance 相距空间；清折行动clearance gauge 测隙规clearance space 间隙空间cleat 夹具clevis U形夹client 委托人climb form technique 提升模板技术climbing lane 爬坡车道clip 小夹close fitting cover 紧合封盖close fittings 紧合配件close-boarded platform 密合封板平台closed area 禁区closed circuit television (CCTV) 闭路电视closed end 不能通行的一端closed position 闭合的位置closure 封闭cloverleaf interchange 四叶式交汇处；蝶式交汇处clutch 离合器co-ordinator 统筹人coal-tar epoxy 环氧煤焦油coarse aggregate 粗集料；粗骨料coarse screening 粗筛coating 保护层；涂层coating material 涂盖物质cock 旋塞；旋阀code of practice 工作守则；操作守则code reader 读码器coefficient 系数coefficient of expansion 膨胀系数coefficient of linear expansion 线性膨胀系数cofferdam 围堰坝cohesive force 黏合力；凝聚力coil 线圈；簧圈；盘管cold milling 刨去路面旧沥青cold reduced steel wire 冷轧钢丝cold solvent welding 冷冻溶剂焊接cold storage 冷藏库collapse 坍塌collapsible cantilever platform 可摺悬臂平台collapsible gate 摺闸collar 护圈；束套；套环collet 套爪；筒夹colluvial deposit 崩积土层colour code 色码colour light signal 颜色灯号coloured cement 颜色水泥column 柱column cap 柱帽column footing 柱基脚column frame 柱架column head 柱头combined dead load 组合恒载combined effect 混合效应combined footing 联合基脚combined load 合并载重combustible goods 可燃物品combustible material 可燃烧物料combustion 燃烧combustion chamber 燃烧室commencement of operation 开始操作commercial building 商业建筑物commercial complex 商场commercial land 商业用地commercial use 商业用途commissioning 启用；投产；投入服务；开始使用；开始运作commitment 承担common corridor 公用走廊common part 公用部分common use 共同使用common waste pipe 共用废水管communal facilities 公用设施communication channel/link 通讯渠道communication system 通讯系统commutator 整流器commuter 交通工具的经常乘客compacted concrete 压实混凝土compaction 压实；夯实compaction pile 压实桩compaction test 压实测试compartment 分隔室；隔室compartment wall 分隔墙compatibility 相配；相容compensating valve 补偿阀compensation 补偿；补偿金competent person 合资格人士；有资格人士complement 补充设备complete function test 全面功能试验complete fusion 完全熔接complete overhaul 全面大修completed works 已完成的工程compliance 遵从composite beam 组合梁composite building 综合用途建筑物composite pile 混合桩composite sandwich construction 复合夹层结构composite steel plate 复合钢板composite wall 组合墙composition 成分compound 场地；合成物comprehensive details 全面细节；整体细节comprehensive development area 综合发展区comprehensive redevelopment area 综合重建区comprehensive transport interchange facilities 综合交通交汇设施comprehensive transport study 整体运输研究compressed air 压缩空气compressed air tunnelling method 压缩空气开挖隧道法compressed gas 压缩气体compressing tool 压挤工具compression 压缩compression joint 承压接缝compression load 压缩荷载compression reinforcement 受压钢筋compression test 抗压测试compressive failure 压缩塌毁；压缩毁坏compressive strength 抗压强度compressive stress 抗压应力compressor 压缩机computer aided design (CAD) facilities 电脑辅助设计设施computer graphics 电脑绘图computerized automatic concrete cube crushing machine 电脑化混凝土立方块压力试验机。

起重机械bridge crane，桥吊chain block，倒链crawler（caterpillar）crane，履带式吊车electric winch，电动葫芦fork lift，叉车gantry crane，门机hoist，启闭机hydraulic hoist，液压启闭机wire rope hoist，固定卷扬机式启闭机mobile crane，汽车吊portal crane，桥式启闭机tower crane，塔吊truck with crane，汽车式起重机运输机械ambulance，救护车bulk cement truck，散装水泥车conveyor belt，输送代dump truck，自卸卡车fire engine，消防车flat bed trailer，平板拖车front dumper，前自卸车front tipper，前翻斗车fuel tank，油罐车loader，装载机loader for shafts，竖井用装运机lorry，货车，载重车low bed trailer，低底盘拖车mine car，矿车mucking machine，出碴车pick-up，小吨位卡车（皮卡车）ready-mix concrete truck，混凝土搅拌车rear dumper，后卸式汽车refrigerated truck冷藏车rigid flat truck，平板车skip lorry，翻斗卡车three-wheeler，三轮车tractor，拖拉机transit mixer，搅拌车truck agitator，搅拌车vacuum silica fume tanker，真空硅粉罐车water tanker，洒水车wheel loader，轮式装载机混凝土生产、浇筑及振捣机械aggregate cooling silo，骨料冷却仓cement silo，水泥罐compartment silo，隔仓罐concrete batcher（distributor），混凝土配料器concrete bucket，混凝土吊罐concrete feeder，混凝土喂料器concrete mixer，混凝土拌和机concrete rehandling silo，混凝土再处理罐creter crane，胎带机dry method shotcreting machine，混凝土干喷机electric vibrator，电动振动棒external vibrator，附者式振捣器flyash silo，粉煤灰罐grout pump and mixer，灌浆泵和拌和机high speed vibrator，高频振捣器ice-plant，制冰厂mobile concrete pump，移动式混凝土泵pneumatic vibrator，气动振动泵sack emptying machine，倒带机stationary concrete pump，固定式混凝土泵tower belt，塔带water chiller，水冷却器wet shotcreting machine，混凝土湿喷机钻孔开挖及支护机械设备3-arm jumbo drill，3臂凿岩台车backhoe，反铲breaker hammer，jet hammer手风钻bulldozer，推土机clamshell，抓铲climbing platform，升降平台column drill，架式风钻crawler excavator，履带式挖掘机down-hole drill，潜孔钻explosive truck，炸药车face shovel，正铲hand drill，手钻hydraulic rockbreaker for excavation backhoe，反铲液压碎石机hydrofraise，水力铰刀（双轮铣）jackhammer，风镐multi-boom drill，多臂钻percussion chisels，冲击钻percussive hammer，冲击锤pneumatic concretebreaker，风动混凝土破碎机pneumatic rockbreaker，风动岩石破碎机pneumatic rockdrill，风动岩石钻机ripper for dozer，裂土器rockbolting machine，锚杆机scabling rod，撬棍table drill，台钻trenching machine，挖沟机wheel excavator，轮式挖掘机填筑碾压机械frog tamper，蛙夯grader（leveler，scrape），平地机hand guide heavy duty mechanical tamper，手扶式机械夯hand guided vibratory roller，手扶式振动碾rammer，夯实机roller compactor，碾压机smooth drum vibratory roller，振动平碾special compactor，专门压土机tamping foot vibratory roller，羊足碾vibration plate compactor，平板振动碾压机vibration roller，振动碾材料加工机械hand saw，带锯bar bending machine，弯筋机bar cutter，钢筋切断机bench planer，台式刨床bench saw，台式锯breaker，破碎机classifier，分选机column drilling machine，柱式钻床concrete saw，混凝土锯diesel welder，柴油焊机double grinder，双层磨床drilling machine，钻床electric welder，电气焊机gasoline chain saw，机械链锯grinder，砂轮机grinding machine，磨床hand circular saw，摇杆圆锯平台horizontal drilling machine，卧式钻床magnet drilling machine，磁力钻床milling machine，铣床mobile circular saw bench，移动圆锯平台planing machine，刨床radial arm saw，圆盘踞radial drilling machine，径向钻床rod mill，棒磨机sand blasting machine，喷砂枪shaping machine，刨床sharpening machine，磨钻机shield circular saw bench，手工电弧焊stationary circular saw bench，固定圆锯平台swinging saw，册移圆锯welding rectifier，焊接纠正仪。

陶瓷ceramics合成纤维synthetic fibre电化学腐蚀electrochemical corrosion 车架automotive chassis悬架suspension转向器redirector变速器speed changer板料冲压sheet metal parts孔加工spot facing machining车间workshop工程技术人员engineer气动夹紧pneuma lock数学模型mathematical model画法几何descriptive geometry机械制图Mechanical drawing投影projection视图view剖视图profile chart标准件standard component零件图part drawing装配图assembly drawing尺寸标注size marking技术要求technical requirements刚度rigidity内力internal force位移displacement截面section疲劳极限fatigue limit断裂fracture塑性变形plastic distortion脆性材料brittleness material刚度准则rigidity criterion垫圈washer垫片spacer直齿圆柱齿轮straight toothed spur gear 斜齿圆柱齿轮helical-spur gear直齿锥齿轮straight bevel gear运动简图kinematic sketch齿轮齿条pinion and rack蜗杆蜗轮worm and worm gear虚约束passive constraint曲柄crank摇杆racker凸轮cams共轭曲线conjugate curve范成法generation method定义域definitional domain值域range导数\\微分differential coefficient求导derivation定积分definite integral不定积分indefinite integral曲率curvature偏微分partial differential毛坯rough游标卡尺slide caliper千分尺micrometer calipers攻丝tap二阶行列式second order determinant逆矩阵inverse matrix线性方程组linear equations概率probability随机变量random variable排列组合permutation and combination气体状态方程equation of state of gas动能kinetic energy势能potential energy机械能守恒conservation of mechanical energy 动量momentum桁架truss轴线axes余子式cofactor逻辑电路logic circuit触发器flip-flop脉冲波形pulse shape数模digital analogy液压传动机构fluid drive mechanism机械零件mechanical parts淬火冷却quench淬火hardening回火tempering调质hardening and tempering磨粒abrasive grain结合剂bonding agent砂轮grinding wheel后角clearance angle龙门刨削planing主轴spindle主轴箱headstock卡盘chuck加工中心machining center车刀lathe tool车床lathe钻削镗削bore车削turning磨床grinder基准benchmark钳工locksmith锻forge压模stamping焊weld拉床broaching machine拉孔broaching装配assembling铸造found流体动力学fluid dynamics流体力学fluid mechanics加工machining液压hydraulic pressure切线tangent机电一体化mechanotronics mechanical-electrical integration 气压air pressure pneumatic pressure稳定性stability介质medium液压驱动泵fluid clutch液压泵hydraulic pump阀门valve失效invalidation强度intensity载荷load应力stress安全系数safty factor可靠性reliability螺纹thread螺旋helix键spline销pin滚动轴承rolling bearing滑动轴承sliding bearing弹簧spring制动器arrester brake十字结联轴节crosshead联轴器coupling链chain皮带strap精加工finish machining粗加工rough machining变速箱体gearbox casing腐蚀rust氧化oxidation磨损wear耐用度durability随机信号random signal离散信号discrete signal超声传感器ultrasonic sensor集成电路integrate circuit挡板orifice plate残余应力residual stress套筒sleeve扭力torsion冷加工cold machining电动机electromotor汽缸cylinder过盈配合interference fit热加工hotwork摄像头CCD camera倒角rounding chamfer优化设计optimal design工业造型设计industrial moulding design有限元finite element滚齿hobbing插齿gear shaping伺服电机actuating motor铣床milling machine钻床drill machine镗床boring machine步进电机stepper motor丝杠screw rod导轨lead rail组件subassembly可编程序逻辑控制器Programmable Logic Controller PLC 电火花加工electric spark machining电火花线切割加工electrical discharge wire - cutting相图phase diagram热处理heat treatment固态相变solid state phase changes有色金属nonferrous metal陶瓷ceramics合成纤维synthetic fibre电化学腐蚀electrochemical corrosion车架automotive chassis悬架suspension转向器redirector变速器speed changer板料冲压sheet metal parts孔加工spot facing machining车间workshop工程技术人员engineer气动夹紧pneuma lock数学模型mathematical model画法几何descriptive geometry机械制图Mechanical drawing投影projection视图view剖视图profile chart标准件standard component零件图part drawing装配图assembly drawing尺寸标注size marking技术要求technical requirements刚度rigidity内力internal force位移displacement截面section疲劳极限fatigue limit断裂fracture塑性变形plastic distortion脆性材料brittleness material刚度准则rigidity criterion垫圈washer垫片spacer直齿圆柱齿轮straight toothed spur gear 斜齿圆柱齿轮helical-spur gear直齿锥齿轮straight bevel gear运动简图kinematic sketch齿轮齿条pinion and rack蜗杆蜗轮worm and worm gear虚约束passive constraint曲柄crank摇杆racker凸轮cams共轭曲线conjugate curve范成法generation method定义域definitional domain值域range导数\\微分differential coefficient求导derivation定积分definite integral不定积分indefinite integral曲率curvature偏微分partial differential毛坯rough游标卡尺slide caliper千分尺micrometer calipers攻丝tap二阶行列式second order determinant逆矩阵inverse matrix线性方程组linear equations概率probability随机变量random variable排列组合permutation and combination气体状态方程equation of state of gas动能kinetic energy势能potential energy机械能守恒conservation of mechanical energy 动量momentum桁架truss轴线axes余子式cofactor逻辑电路logic circuit触发器flip-flop脉冲波形pulse shape数模digital analogy液压传动机构fluid drive mechanism机械零件mechanical parts淬火冷却quench淬火hardening回火tempering调质hardening and tempering磨粒abrasive grain结合剂bonding agent砂轮grinding wheelAssembly line 组装线Layout 布置图Conveyer 流水线物料板Rivet table 拉钉机Rivet gun 拉钉枪Screw driver 起子Pneumatic screw driver 气动起子worktable 工作桌OOBA 开箱检查fit together 组装在一起fasten 锁紧(螺丝)fixture 夹具(治具)pallet 栈板barcode 条码barcode scanner 条码扫描器fuse together 熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME 制造工程师MT 制造生技cosmetic inspect 外观检查inner parts inspect 内部检查thumb screw 大头螺丝lbs. inch 镑、英寸EMI gasket 导电条front plate 前板rear plate 后板chassis 基座bezel panel 面板power button 电源按键reset button 重置键Hi-pot test of SPS 高源高压测试Voltage switch of SPS 电源电压接拉键sheet metal parts 冲件plastic parts 塑胶件SOP 制造作业程序material check list 物料检查表work cell 工作间trolley 台车carton 纸箱sub-line 支线left fork 叉车personnel resource department 人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer |plein|刨床miller铣床grinder磨床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vice section superisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |\\'skr?pid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |\\' ksi\\'dei?n|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单location地点present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheet PCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet 库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked 待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet 年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕??shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机阿基米德蜗杆Archimedes worm安全系数safety factor; factor of safety安全载荷safe load凹面、凹度concavity扳手wrench板簧flat leaf spring半圆键woodruff key变形deformation摆杆oscillating bar摆动从动件oscillating follower摆动从动件凸轮机构cam with oscillating follower 摆动导杆机构oscillating guide-bar mechanism 摆线齿轮cycloidal gear摆线齿形cycloidal tooth profile摆线运动规律cycloidal motion摆线针轮cycloidal-pin wheel包角angle of contact保持架cage背对背安装back-to-back arrangement背锥back cone ；normal cone背锥角back angle背锥距back cone distance比例尺scale比热容specific heat capacity闭式链closed kinematic chain闭链机构closed chain mechanism臂部arm变频器frequency converters变频调速frequency control of motor speed变速speed change变速齿轮change gear change wheel变位齿轮modified gear变位系数modification coefficient标准齿轮standard gear标准直齿轮standard spur gear表面质量系数superficial mass factor表面传热系数surface coefficient of heat transfer表面粗糙度surface roughness并联式组合combination in parallel并联机构parallel mechanism并联组合机构parallel combined mechanism并行工程concurrent engineering并行设计concurred design, CD不平衡相位phase angle of unbalance不平衡imbalance (or unbalance)不平衡量amount of unbalance不完全齿轮机构intermittent gearing波发生器wave generator波数number of waves补偿compensation参数化设计parameterization design, PD残余应力residual stress操纵及控制装置operation control device槽轮Geneva wheel槽轮机构Geneva mechanism ；Maltese cross槽数Geneva numerate槽凸轮groove cam侧隙backlash差动轮系differential gear train差动螺旋机构differential screw mechanism差速器differential常用机构conventional mechanism; mechanism in common use 车床lathe承载量系数bearing capacity factor承载能力bearing capacity成对安装paired mounting尺寸系列dimension series齿槽tooth space齿槽宽spacewidth齿侧间隙backlash齿顶高addendum齿顶圆addendum circle齿根高dedendum齿根圆dedendum circle齿厚tooth thickness齿距circular pitch齿宽face width齿廓tooth profile齿廓曲线tooth curve齿轮gear齿轮变速箱speed-changing gear boxes齿轮齿条机构pinion and rack齿轮插刀pinion cutter; pinion-shaped shaper cutter 齿轮滚刀hob ,hobbing cutter齿轮机构gear齿轮轮坯blank齿轮传动系pinion unit齿轮联轴器gear coupling齿条传动rack gear齿数tooth number齿数比gear ratio齿条rack齿条插刀rack cutter; rack-shaped shaper cutter齿形链、无声链silent chain齿形系数form factor齿式棘轮机构tooth ratchet mechanism插齿机gear shaper重合点coincident points重合度contact ratio冲床punch传动比transmission ratio, speed ratio传动装置gearing; transmission gear传动系统driven system传动角transmission angle传动轴transmission shaft串联式组合combination in series串联式组合机构series combined mechanism串级调速cascade speed control创新innovation creation创新设计creation design垂直载荷、法向载荷normal load唇形橡胶密封lip rubber seal磁流体轴承magnetic fluid bearing从动带轮driven pulley从动件driven link, follower从动件平底宽度width of flat-face从动件停歇follower dwell从动件运动规律follower motion从动轮driven gear粗线bold line粗牙螺纹coarse thread大齿轮gear wheel打包机packer打滑slipping带传动belt driving带轮belt pulley带式制动器band brake单列轴承single row bearing单向推力轴承single-direction thrust bearing单万向联轴节single universal joint单位矢量unit vector当量齿轮equivalent spur gear; virtual gear当量齿数equivalent teeth number; virtual number of teeth当量摩擦系数equivalent coefficient of friction当量载荷equivalent load刀具cutter导数derivative倒角chamfer导热性conduction of heat导程lead导程角lead angle等加等减速运动规律parabolic motion; constant acceleration and deceleration motion等速运动规律uniform motion; constant velocity motion等径凸轮conjugate yoke radial cam等宽凸轮constant-breadth cam等效构件equivalent link等效力equivalent force等效力矩equivalent moment of force等效量equivalent等效质量equivalent mass等效转动惯量equivalent moment of inertia等效动力学模型dynamically equivalent model底座chassis低副lower pair点划线chain dotted line（疲劳）点蚀pitting垫圈gasket垫片密封gasket seal碟形弹簧belleville spring顶隙bottom clearance定轴轮系ordinary gear train; gear train with fixed axes动力学dynamics动密封kinematical seal动能dynamic energy动力粘度dynamic viscosity动力润滑dynamic lubrication动平衡dynamic balance动平衡机dynamic balancing machine动态特性dynamic characteristics动态分析设计dynamic analysis design动压力dynamic reaction动载荷dynamic load端面transverse plane端面参数transverse parameters端面齿距transverse circular pitch端面齿廓transverse tooth profile端面重合度transverse contact ratio端面模数transverse module端面压力角transverse pressure angle锻造forge对称循环应力symmetry circulating stress对心滚子从动件radial (or in-line ) roller follower对心直动从动件radial (or in-line ) translating follower对心移动从动件radial reciprocating follower对心曲柄滑块机构in-line slider-crank (or crank-slider) mechanism 多列轴承multi-row bearing多楔带poly V-belt多项式运动规律polynomial motion多质量转子rotor with several masses惰轮idle gear额定寿命rating life额定载荷load ratingII 级杆组dyad发生线generating line发生面generating plane法面normal plane法面参数normal parameters法面齿距normal circular pitch法面模数normal module法面压力角normal pressure angle法向齿距normal pitch法向齿廓normal tooth profile法向直廓蜗杆straight sided normal worm法向力normal force反馈式组合feedback combining反向运动学inverse ( or backward) kinematics反转法kinematic inversion反正切Arctan范成法generating cutting仿形法form cutting方案设计、概念设计concept design, CD防振装置shockproof device飞轮flywheel飞轮矩moment of flywheel非标准齿轮nonstandard gear非接触式密封non-contact seal非周期性速度波动aperiodic speed fluctuation非圆齿轮non-circular gear粉末合金powder metallurgy分度线reference line; standard pitch line分度圆reference circle; standard (cutting) pitch circle 分度圆柱导程角lead angle at reference cylinder分度圆柱螺旋角helix angle at reference cylinder分母denominator分子numerator分度圆锥reference cone; standard pitch cone分析法analytical method封闭差动轮系planetary differential复合铰链compound hinge复合式组合compound combining复合轮系compound (or combined) gear train复合平带compound flat belt复合应力combined stress复式螺旋机构Compound screw mechanism复杂机构complex mechanism杆组Assur group干涉interference刚度系数stiffness coefficient刚轮rigid circular spline钢丝软轴wire soft shaft刚体导引机构body guidance mechanism刚性冲击rigid impulse (shock)刚性转子rigid rotor刚性轴承rigid bearing刚性联轴器rigid coupling高度系列height series高速带high speed belt高副higher pair格拉晓夫定理Grashoff`s law根切undercutting公称直径nominal diameter高度系列height series功work工况系数application factor工艺设计technological design工作循环图working cycle diagram工作机构operation mechanism工作载荷external loads工作空间working space工作应力working stress工作阻力effective resistance工作阻力矩effective resistance moment公法线common normal line公共约束general constraint公制齿轮metric gears功率power功能分析设计function analyses design共轭齿廓conjugate profiles共轭凸轮conjugate cam构件link鼓风机blower固定构件fixed link; frame固体润滑剂solid lubricant关节型操作器jointed manipulator惯性力inertia force惯性力矩moment of inertia ,shaking moment 惯性力平衡balance of shaking force惯性力完全平衡full balance of shaking force惯性力部分平衡partial balance of shaking force 惯性主矩resultant moment of inertia惯性主失resultant vector of inertia冠轮crown gear广义机构generation mechanism广义坐标generalized coordinate轨迹生成path generation轨迹发生器path generator滚刀hob滚道raceway滚动体rolling element滚动轴承rolling bearing滚动轴承代号rolling bearing identification code 滚针needle roller滚针轴承needle roller bearing滚子roller滚子轴承roller bearing滚子半径radius of roller滚子从动件roller follower滚子链roller chain滚子链联轴器double roller chain coupling滚珠丝杆ball screw滚柱式单向超越离合器roller clutch过度切割undercutting函数发生器function generator函数生成function generation含油轴承oil bearing耗油量oil consumption耗油量系数oil consumption factor赫兹公式H. Hertz equation合成弯矩resultant bending moment合力resultant force合力矩resultant moment of force黑箱black box横坐标abscissa互换性齿轮interchangeable gears花键spline滑键、导键feather key滑动轴承sliding bearing滑动率sliding ratio滑块slider环面蜗杆toroid helicoids worm环形弹簧annular spring缓冲装置shocks; shock-absorber灰铸铁grey cast iron回程return回转体平衡balance of rotors混合轮系compound gear train积分integrate机电一体化系统设计mechanical-electrical integration system design 机构mechanism机构分析analysis of mechanism机构平衡balance of mechanism机构学mechanism机构运动设计kinematic design of mechanism机构运动简图kinematic sketch of mechanism机构综合synthesis of mechanism机构组成constitution of mechanism机架frame, fixed link机架变换kinematic inversion机器machine机器人robot机器人操作器manipulator机器人学robotics技术过程technique process技术经济评价technical and economic evaluation技术系统technique system机械machinery机械创新设计mechanical creation design, MCD机械系统设计mechanical system design, MSD机械动力分析dynamic analysis of machinery机械动力设计dynamic design of machinery机械动力学dynamics of machinery机械的现代设计modern machine design机械系统mechanical system机械利益mechanical advantage机械平衡balance of machinery机械手manipulator机械设计machine design; mechanical design机械特性mechanical behavior机械调速mechanical speed governors机械效率mechanical efficiency机械原理theory of machines and mechanisms机械运转不均匀系数coefficient of speed fluctuation机械无级变速mechanical stepless speed changes基础机构fundamental mechanism基本额定寿命basic rating life基于实例设计case-based design,CBD基圆base circle基圆半径radius of base circle基圆齿距base pitch基圆压力角pressure angle of base circle基圆柱base cylinder基圆锥base cone急回机构quick-return mechanism急回特性quick-return characteristics急回系数advance-to return-time ratio急回运动quick-return motion棘轮ratchet棘轮机构ratchet mechanism棘爪pawl极限位置extreme (or limiting) position极位夹角crank angle between extreme (or limiting) positions计算机辅助设计computer aided design, CAD计算机辅助制造computer aided manufacturing, CAM计算机集成制造系统computer integrated manufacturing system, CIMS 计算力矩factored moment; calculation moment计算弯矩calculated bending moment加权系数weighting efficient加速度acceleration加速度分析acceleration analysis加速度曲线acceleration diagram尖点pointing; cusp尖底从动件knife-edge follower间隙backlash间歇运动机构intermittent motion mechanism 减速比reduction ratio减速齿轮、减速装置reduction gear减速器speed reducer减摩性anti-friction quality渐开螺旋面involute helicoid渐开线involute渐开线齿廓involute profile渐开线齿轮involute gear渐开线发生线generating line of involute渐开线方程involute equation渐开线函数involute function渐开线蜗杆involute worm渐开线压力角pressure angle of involute渐开线花键involute spline简谐运动simple harmonic motion键key键槽keyway交变应力repeated stress交变载荷repeated fluctuating load交叉带传动cross-belt drive交错轴斜齿轮crossed helical gears胶合scoring角加速度angular acceleration角速度angular velocity角速比angular velocity ratio角接触球轴承angular contact ball bearing角接触推力轴承angular contact thrust bearing 角接触向心轴承angular contact radial bearing 角接触轴承angular contact bearing铰链、枢纽hinge校正平面correcting plane接触应力contact stress接触式密封contact seal阶梯轴multi-diameter shaft结构structure结构设计structural design截面section节点pitch point节距circular pitch; pitch of teeth节线pitch line节圆pitch circle节圆齿厚thickness on pitch circle节圆直径pitch diameter节圆锥pitch cone节圆锥角pitch cone angle解析设计analytical design紧边tight-side紧固件fastener径节diametral pitch径向radial direction径向当量动载荷dynamic equivalent radial load径向当量静载荷static equivalent radial load径向基本额定动载荷basic dynamic radial load rating 径向基本额定静载荷basic static radial load tating径向接触轴承radial contact bearing径向平面radial plane径向游隙radial internal clearance径向载荷radial load径向载荷系数radial load factor径向间隙clearance静力static force静平衡static balance静载荷static load静密封static seal局部自由度passive degree of freedom矩阵matrix矩形螺纹square threaded form锯齿形螺纹buttress thread form矩形牙嵌式离合器square-jaw positive-contact clutch 绝对尺寸系数absolute dimensional factor绝对运动absolute motion绝对速度absolute velocity均衡装置load balancing mechanism抗压强度compression strength开口传动open-belt drive开式链open kinematic chain开链机构open chain mechanism可靠度degree of reliability可靠性reliability可靠性设计reliability design, RD空气弹簧air spring空间机构spatial mechanism空间连杆机构spatial linkage空间凸轮机构spatial cam空间运动副spatial kinematic pair空间运动链spatial kinematic chain空转idle宽度系列width series框图block diagram雷诺方程Reynolds‘s equation离心力centrifugal force离心应力centrifugal stress离合器clutch离心密封centrifugal seal理论廓线pitch curve理论啮合线theoretical line of action隶属度membership力force力多边形force polygon力封闭型凸轮机构force-drive (or force-closed) cam mechanism 力矩moment力平衡equilibrium力偶couple力偶矩moment of couple连杆connecting rod, coupler连杆机构linkage连杆曲线coupler-curve连心线line of centers链chain链传动装置chain gearing链轮sprocket sprocket-wheel sprocket gear chain wheel联组V 带tight-up V belt联轴器coupling shaft coupling两维凸轮two-dimensional cam临界转速critical speed六杆机构six-bar linkage龙门刨床double Haas planer轮坯blank轮系gear train螺杆screw螺距thread pitch螺母screw nut螺旋锥齿轮helical bevel gear螺钉screws螺栓bolts螺纹导程lead螺纹效率screw efficiency螺旋传动power screw螺旋密封spiral seal螺纹thread (of a screw)螺旋副helical pair螺旋机构screw mechanism螺旋角helix angle螺旋线helix ,helical line绿色设计green design design for environment马耳他机构Geneva wheel Geneva gear马耳他十字Maltese cross脉动无级变速pulsating stepless speed changes脉动循环应力fluctuating circulating stress脉动载荷fluctuating load铆钉rivet迷宫密封labyrinth seal密封seal密封带seal belt密封胶seal gum密封元件potted component密封装置sealing arrangement面对面安装face-to-face arrangement面向产品生命周期设计design for product`s life cycle, DPLC 名义应力、公称应力nominal stress模块化设计modular design, MD模块式传动系统modular system模幅箱morphology box模糊集fuzzy set模糊评价fuzzy evaluation模数module摩擦friction摩擦角friction angle摩擦力friction force摩擦学设计tribology design, TD摩擦阻力frictional resistance摩擦力矩friction moment摩擦系数coefficient of friction摩擦圆friction circle磨损abrasion wear; scratching末端执行器end-effector目标函数objective function耐腐蚀性corrosion resistance耐磨性wear resistance挠性机构mechanism with flexible elements挠性转子flexible rotor内齿轮internal gear内齿圈ring gear内力internal force内圈inner ring能量energy能量指示图viscosity逆时针counterclockwise (or anticlockwise)啮出engaging-out啮合engagement, mesh, gearing啮合点contact points啮合角working pressure angle啮合线line of action啮合线长度length of line of action啮入engaging-in牛头刨床shaper凝固点freezing point; solidifying point扭转应力torsion stress扭矩moment of torque扭簧helical torsion spring诺模图NomogramO 形密封圈密封O ring seal盘形凸轮disk cam盘形转子disk-like rotor抛物线运动parabolic motion疲劳极限fatigue limit疲劳强度fatigue strength偏置式offset偏( 心) 距offset distance偏心率eccentricity ratio偏心质量eccentric mass偏距圆offset circle偏心盘eccentric偏置滚子从动件offset roller follower偏置尖底从动件offset knife-edge follower偏置曲柄滑块机构offset slider-crank mechanism 拼接matching评价与决策evaluation and decision频率frequency平带flat belt平带传动flat belt driving平底从动件flat-face follower平底宽度face width平分线bisector平均应力average stress平均中径mean screw diameter平均速度average velocity平衡balance平衡机balancing machine平衡品质balancing quality平衡平面correcting plane平衡质量balancing mass平衡重counterweight平衡转速balancing speed平面副planar pair, flat pair平面机构planar mechanism平面运动副planar kinematic pair平面连杆机构planar linkage平面凸轮planar cam平面凸轮机构planar cam mechanism平面轴斜齿轮parallel helical gears普通平键parallel key其他常用机构other mechanism in common use起动阶段starting period启动力矩starting torque气动机构pneumatic mechanism奇异位置singular position起始啮合点initial contact , beginning of contact气体轴承gas bearing千斤顶jack嵌入键sunk key强迫振动forced vibration切齿深度depth of cut曲柄crank曲柄存在条件Grashoff`s law曲柄导杆机构crank shaper (guide-bar) mechanism曲柄滑块机构slider-crank (or crank-slider) mechanism 曲柄摇杆机构crank-rocker mechanism曲齿锥齿轮spiral bevel gear曲率curvature曲率半径radius of curvature曲面从动件curved-shoe follower曲线拼接curve matching曲线运动curvilinear motion曲轴crank shaft驱动力driving force驱动力矩driving moment (torque)。

机械工程英语词汇在机械工程领域中，掌握基本的英语词汇对于与国际商业伙伴和客户进行沟通至关重要。

本文将介绍一些常用的机械工程英语词汇，帮助读者扩展词汇量并提高沟通能力。

1. 机械工程基础词汇1.1 机械元件（Mechanical Components）•Bearing: 轴承•Gasket: 垫圈•Pulley: 滑轮•Spring: 弹簧•Valve: 阀门•Shaft: 轴•Bolt: 螺栓•Nut: 螺母•Washer: 垫圈1.2 设备与工具（Equipment and Tools）•Drill: 钻机•Milling machine: 铣床•Grinder: 磨床•Welding machine: 焊机•Screwdriver: 螺丝刀•Hammer: 锤子•Wrench: 扳手•Pliers: 钳子•Measuring tape: 卷尺1.3 流体力学（Fluid Mechanics）•Fluid: 流体•Pressure: 压力•Flow rate: 流速•Viscosity: 粘度•Turbulence: 湍流•Pump: 泵•Pipe: 管道•Valve: 阀门•Filter: 过滤器•Heat exchanger: 热交换器2. 机械工程领域词汇2.1 设计与制造（Design and Manufacturing）•CAD (Computer-ded Design): 计算机辅助设计•CAM (Computer-ded Manufacturing): 计算机辅助制造•Prototype: 原型•Assembly: 组装•Machining: 加工•Tolerance: 公差•CNC (Computer Numerical Control): 计算机数控•Molding: 成型•Casting: 铸造•Forging: 锻造2.2 热力学与热能（Thermodynamics and Heat Energy）•Thermal expansion: 热膨胀•Heat transfer: 热传递•Efficiency: 效率•Turbine: 涡轮机•Condenser: 冷凝器•Boiler: 锅炉•Refrigeration: 制冷•Combustion: 燃烧•Thermocouple: 热电偶•Heat sink: 散热器2.3 控制与自动化（Control and Automation）•PLC (Programmable Logic Controller): 可编程逻辑控制器•Sensor: 传感器•Actuator: 执行器•Feedback: 反馈•PID (Proportional-Integral-Derivative) controller: 比例积分微分控制器•HMI (Human Machine Interface): 人机界面•SCADA (Supervisory Control and Data Acquisition): 监控与数据采集系统•Robotics: 机器人技术•Automated assembly line: 自动化生产线•Control panel: 控制面板3. 机械工程领域常用短语3.1 项目管理（Project Management）•Project timeline: 项目进度表•Cost estimation: 成本估算•Risk assessment: 风险评估•Quality control: 质量控制•Milestone: 里程碑•Gantt chart: 甘特图•Budget allocation: 预算分配•Procurement process: 采购过程•Resource allocation: 资源分配•Project completion: 项目完成3.2 维护与修理（Mntenance and Repr）•Routine mntenance: 定期维护•Troubleshooting: 故障排除•Spare parts: 备件•Preventive mntenance: 预防性维护•Breakdown mntenance: 故障维修•Lubrication: 润滑•Calibration: 校准•Downtime: 停机时间•Inspection: 检查•Overhaul: 大修3.3 报告与文件（Reports and Documents）•Technical specifications: 技术规范•Test report: 测试报告•Safety manual: 安全手册•User manual: 使用手册•Engineering drawing: 工程图纸•Schematic diagram: 示意图•Bill of Materials (BOM): 物料清单•Change request: 变更请求•Warranty documentation: 保修文件•Risk assessment report: 风险评估报告以上是一些常用的机械工程英语词汇和短语，希望读者能通过学习和应用这些词汇，提高在机械工程领域的英语沟通能力，更好地与国际伙伴和客户合作。