DIN 929-2000 六角焊接螺母

January 2000©No part of this translation may be reproduced without the prior permission ofDIN Deutsches Institut für Normung e.V., Berlin. Beuth Verlag GmbH, 10772Berlin, Germany, has the exclusive right of sale for German Standards (DIN-Normen).English price group06Sales No.010606.00Page 2DIN 929:2000-01DIN 13-1General purpose ISO metric screw threads – Nominal sizes for 1 mm to 68 mm diameter coarse pitch threadsDIN 13-5General purpose ISO metric screw threads – Nominal sizes for 1 mm and 1,25 mm finepitch threads with diameters from 7,5 mm to 200 mmDIN 13-6General purpose ISO metric screw threads – Nominal sizes for 1,5 mm fine pitch threadswith diameters from 12 mm to 300 mmDIN 13-15ISO metric screw threads – Fundamental deviations and tolerances for screw threads of1 mm diameter and largerDIN 267-2Fasteners – Technical delivery conditions – Product grades and tolerances DIN 977Hexagon weld nuts with flange DIN 4000-2Tabular layouts of article characteristics for bolts, screws and fit bolts DIN EN 20898-2Mechanical properties of fasteners – Part 2: Nuts with coarse pitch thread and specifiedproof load values (ISO 898-2:1992)DIN EN ISO 898-1Mechanical properties of fasteners made of carbon steel and alloy steel – Part 1: Bolts,screws and studs (ISO 898-1:1999)DIN EN ISO 898-6Mechanical properties of fasteners – Part 6: Nuts with fine pitch thread and specifiedproof load values (ISO 898-6:1994)DIN EN ISO 3269Fasteners – Acceptance inspection (ISO/DIS 3269:1998)*)DIN EN ISO 4042Fasteners – Electroplated coatings (ISO 4042:1999)DIN EN ISO 4759-1Tolerances for fasteners – Part 1: Bolts, screws, studs and fit bolts – Product grades A,B andC (ISO/DIS 4759-1:1997)*)ISO 8992:1986Fasteners – General requirements for bolts, screws, studs and fit bolts ANSI B1.1-1989Unified inch screw threads (UN and UNR thread form)1)*) Currently at draft stage.1) Obtainable from Beuth Verlag GmbH (Auslandsnormen-Service), 10772 Berlin, Germany.Detail XDetail Y(sectional view)Page3 DIN929:2000-01Page4DIN929:2000-01Nut DIN 929 – M10 – StNut DIN 929 – 7/16-20 UNF-2B – SW17 – StPage 5DIN 929:2000-017Figure 2:8Figure 3:。

2000年4月7日第一版00工厂现有DIN标准目录及与GB国标参考对照表0本文件使用说明：01、本文件没有经过编制部门的同意，任何人不得私自更改和删除。

002、本文件中所列相关标准，在总师办均可查到完整的标准原件，欢迎查阅使用。

003、本文件中所列相关标准对照仅供参考。

由于许多DIN 标准无法与GB标准完全等同，所以具体使用中应参阅原标准文件对照选用。

0序号D IN标准号中文名称参考GB国标号备注1 DIN 1圆锥销GB117-862 DIN 7 圆柱销GB119-863 DIN13T13 公制ISO螺纹GB196-814 DIN 93 单耳止动垫圈GB854-885 DIN 94开口销GB91-866 DIN 95开槽半沉头木螺钉GB101-867 DIN 101 铆钉技术条件GB116-868 DIN 124 半圆头铆钉GB863.1-869 DIN 125垫片(精制) GB97.1(2)-8510 DIN 126垫片(粗制) GB95-8511 DIN 127弹簧垫圈GB7244-8712 DIN 128 弹簧垫圈（鞍形及波形）GB7246-87 、GB7245-8713 DIN 137 弹簧垫圈（鞍形及波形）GB860-87 、GB955-8714 DIN 258 螺伪锥销GB881-8615 DIN 267 金属连接元件16 DIN 268 切向键及键槽GB1974-8017 DIN 271 切向键及键槽GB1974-8018 DIN 302 沉头铆钉GB866-8619 DIN 315 碟形螺母GB94.1-8720 DIN 431 管螺母GB62-8821 DIN 432外舌止动垫圈GB856-8822 DIN 433垫圈(针对螺栓)23 DIN 434垫圈(矩形,用于U形梁)24 DIN 435垫圈(矩形,用于I形梁)25 DIN 436垫圈(矩形,用于木形梁)26 DIN 439轻型六角螺母GB6174-8627 DIN 440垫圈(用于木结构) GB5287-85(圆孔)28 DIN 442密封盖(压制型)29 DIN 463双耳止动垫圈GB855-8830 DIN 466滚花螺母（高式）GB806-8831 DIN 467滚花螺母（低式）GB807-8832 DIN 471弹性挡圈(轴用) GB894.1(2)-8633 DIN 472弹性挡圈(孔用) GB893.1-8634 DIN 522 金属结构垫圈GB8286-8535 DIN 526 保险帽（与DIN84配用）36 DIN 546 带槽螺母G817-88B37 DIN 547 端面带孔圆螺母GB815-8838 DIN 548 侧面带孔圆螺母GB816-8839 DIN 555螺母(M5～M100×6 C级) GB41-8640 DIN 557 方螺母（C级）41 DIN 562 方螺母（B级薄形）42 DIN 571六角头木螺钉GB102-8643 DIN 582环形螺母GB63-8844 DIN 603大半圆头方颈螺栓GB14-8845 DIN 604沉头带榫螺钉GB11-8846 DIN 625滚动轴承(单列带凹槽) GB176-8247 DIN 660 半圆头铆钉GB867-8648 DIN 661 沉头螺钉49 DIN 662 埋头螺钉50 DIN 674 大扁圆头螺栓GB1011-8651 DIN 675 半埋头螺钉52 DIN 798 锚固用螺母53 DIN 910螺塞54 DIN 912内六角圆头螺钉GB70-8554.1 DIN 913 内六角平端紧定螺钉GB77-8555 DIN 917 六角带帽螺母56 DIN 918 金属连接元件（与ISOB比较）57 DIN 928 方形焊接螺母58 DIN 929 六角焊接螺母GB/T13681-199259 DIN 931 六角螺栓(带柱) GB5782-8660 DIN 933六角螺栓(全螺纹) GB5783-8661 DIN 934六角螺母(A、B级) GB6170-8662 DIN 935T1 六角带槽螺母(A、B级) GB 6178-8663 DIN 935T2 六角带槽螺母(C级) GB 6179-8664 DIN 936 六角薄螺母(A、B级) GB 6172-8665 DIN 937开槽薄螺母GB6181-8666 DIN 938 双头螺柱bm≈1d GB897-8867 DIN 939双头螺柱bm≈1.25d GB898-8868 DIN 946 螺栓、螺母摩擦系数69 DIN 960螺栓GB5782-8670 DIN 963开槽沉头螺钉GB68-8571 DIN 964开槽半沉头螺钉GB69-8572 DIN 971T1 螺母（6、8级）GB6171-8673 DIN 971T2 螺母（10、12级）GB6176-8674 DIN 975螺纹杆75 DIN 979 开槽薄螺母GB6181-8676 DIN 980 螺母77 DIN 982螺母GB41-86、GB6170-8678 DIN 带齿弹性挡圈79 DIN 带齿弹性挡圈80 DIN 985螺母GB6172-8681 DIN 986六角带帽螺母82 DIN 988调整环支撑垫圈GB886-8583 DIN 1143 机械钉84 DIN 1144 平板头钉85 DIN 1151 圆直钉86 DIN 1152 圆直钉87 DIN 1157 装修用钉88 DIN 1158 钩头钉89 DIN 1160 平头钉90 DIN 1163 钉91 DIN 1433无头柱销GB880-8692 DIN 1434小头柱销GB882-8693 DIN 1435小头柱销94 DIN 1436大头柱销95 DIN 1440垫圈（销用中型）GB848-8596 DIN 1441垫圈（粗制）97 DIN 1445 销钉98 DIN 1469 带颈凹口销99 DIN 1471凹口锥销100 DIN 1473凹口柱销101 DIN 1475翼形凹口销102 DIN 1478拉线螺母103 DIN 1479 拉线螺母104 DIN 1480 拉线螺母105 DIN 1481弹性圆柱销（重型）GB879-86 106 DIN 1499张紧套107 DIN 1587 六角带帽螺母GB 802-88 108 DIN 2510 带接口螺母109 DIN 3404平头注油嘴110 DIN 5401球111 DIN 5417开口垫圈112 DIN 5525无头柱销（线路机械用）113 DIN 5526带头柱销（线路机械用）114 DIN 6303 滚花螺母115 DIN 6330 1.5d高六角螺母116 DIN 6331 1.5d高带缘螺母117 DIN 6340 压紧机构用螺母118 DIN 6796 夹紧垫圈119 DIN 6791 圆头带孔铆钉120 DIN 6792 沉头带孔铆钉GB874-86121 DIN 6797 内、外齿锁紧垫圈GB862.2-87、GB861.1-87 、GB956.1-87 122 DIN 6798锯齿锁紧垫圈GB861.2-87、GB862.2-87 、GB956.2-87 123 DIN 6799保险垫片GB896-86 124 DIN 6880精制楔铁125 DIN 6881 孔用楔键126 DIN 6883 平面楔键127 DIN 6884 钩头楔键128 DIN 6885键及槽GB1095-79 129 DIN 6886键及槽GB1563-79 130 DIN 6887钩头楔键GB1565-79 131 DIN 6888半圆键GB1098-79GB1099-79 132 DIN 6889钩头楔键133 DIN 6902 垫圈134 DIN 6903 垫圈135 DIN 6904 波形弹性垫圈136 DIN 6905 鞍形弹性垫圈GB7245-87 137 DIN 6907 外锯齿锁紧垫圈GB862.2-87 138 DIN 6908 夹紧垫圈139 DIN 6912内六角圆柱头螺钉140 DIN 6913带支撑套的弹簧挡圈141 DIN 6914螺栓（长导杆）142 DIN 6915 螺母143 DIN 6916 垫片144 DIN 6917 方楔形垫片145 DIN 6918 方楔形垫片146 DIN 6923 带法兰螺母147 DIN 6924 锁紧螺母148 DIN 6925 锁紧螺母149 DIN 6926 带法兰锁紧螺母150 DIN 6927 带法兰锁紧螺母GB6187-86 151 DIN 7331 空心销152 DIN 7337 抽心铆钉153 DIN 7338 铆钉GB875-86、GB876-86、GB975-86、GB872-86 154 DIN 7339 空心铆钉GB876-86 155 DIN 7340 管状铆钉GB975-86 156 DIN 7341 无头铆钉GB1016-86 157 DIN 7346弹性圆柱销（轻型）158 DIN 7349垫圈159 DIN 7603密封圈160 DIN 7604螺堵161 DIN 7623空心六角螺栓162 DIN 7793 轴、孔用钢丝挡圈GB895.1-86、GB895.2-86 163 DIN 7933加固支座164 DIN 7965旋入螺母165 DIN 7967保险螺母166 DIN 7980弹簧垫圈GB93-87 167 DIN 7984内六角圆柱头螺钉GB70-85 168 DIN 7991内六角沉头螺钉169 DIN 8187滚子链170 DIN 9021垫片GB96-85 171 DIN 9045 张力垫圈172 DIN 00124 插簧173 DIN 22425 三边形螺母174 DIN 71412锥形注油嘴175 DIN 71752 叉头176 DIN 71802角接头组件177 DIN 80705薄螺母178179180181182183184185186187188189190191192193194195196197。

标准汇总（2013年）德国标准（DIN）一.螺栓类序号名称标准代号版本/年号备注1外六角螺栓/全牙DIN93319872外六角螺栓/半牙DIN93119873圆头方颈（马车）螺栓DIN60319814六角法兰螺栓DIN692119835活节螺栓DIN4441983二.螺钉类序号名称标准代号版本/年号备注1开槽圆锥头螺钉DIN8419902开槽盘头螺钉DIN8519903开槽长圆柱端紧钉螺钉DIN41719864开槽长平端紧钉螺钉/半牙DIN42719865开槽凹端紧钉DIN43819866开槽平端紧钉DIN55119867开槽锥端紧钉DIN55319868六角头圆柱端紧钉DIN56119959吊环螺钉DIN580200310内六角锥型闭锁螺钉DIN906199211内六角直型闭锁螺钉DIN908199212外六角锥型闭锁螺钉DIN909199213外六角直型闭锁螺钉DIN910199214内六角扳手DIN911198715内六角圆柱头螺钉DIN912198316内六角平端紧钉DIN913198017内六角尖端紧钉DIN914198018内六角柱端紧钉DIN915198019内六角凹端紧钉DIN916198020开槽沉头螺钉DIN963199021开槽半沉头螺钉DIN964199022十字槽沉头螺钉DIN965199023十字槽半沉头螺钉DIN966199024薄型带孔内六角圆柱头螺钉DIN6912198525薄型内六角圆柱头螺钉DIN7984198526十字槽盘头螺钉DIN7985198627内六角沉头螺钉DIN79911986三、螺柱类序号名称标准代号版本/年号备注1双头螺柱/bm=2d DIN83519952双头螺柱/bm=1d DIN93819953双头螺柱/bm=1.5d DIN93919954双头螺柱/bm=1.25d DIN9401995四、螺母类序号名称标准代号版本/年号备注1蝶形螺母--圆翼DIN31519832管螺母DIN43119823六角薄螺母DIN43919874滚花高螺母DIN46619885滚花薄螺母DIN46719866开槽圆螺母DIN54619867六角螺母/C级DIN55519878四方螺母/C级DIN55719859薄型方螺母/B级DIN562198710吊环螺母DIN582197111薄型盲螺母DIN917198712焊接方螺母DIN928198313焊接六角螺母DIN9291987141型六角螺母DIN934198715六角薄螺母DIN936198516全金属六角锁紧螺母（1型）DIN980198717六角头尼龙锁紧螺母DIN982198718六角头薄型尼龙锁紧螺母DIN985198719六角盖型尼龙锁紧螺母DIN986198720组合式盖型螺母DIN1587198721长六角螺母DIN633422大六角螺母DIN6915198923全金属六角锁紧螺母（2型）DIN6925198724六角法兰面螺母DIN69231983五、自攻钉类序号名称标准代号版本/年号备注1开槽盘头自攻螺钉DIN797119902开槽沉头螺钉DIN797219903开槽半沉头自攻钉DIN797319904六角头自攻钉DIN797619905十字槽盘头自攻钉DIN798119846十字槽沉头自攻钉DIN798219907十字槽半沉头自攻钉DIN798319908自攻自钻螺钉/多种头型DIN75041982六、木螺钉类序号名称标准代号版本/年号备注1开槽半沉头木螺钉DIN9519862开槽半圆头木螺钉DIN9619863开槽沉头木螺钉DIN9719864六角头木螺钉DIN57119865十字槽半沉头木螺钉DIN799519846十字槽圆头木螺钉DIN799619867十字槽沉头木螺钉DIN79971984七、垫圈类序号名称标准代号版本/年号备注1平垫DIN125-A19902平垫(带倒角)DIN125-B19903平垫DIN12619904重型弹垫DIN127A19875标准弹垫DIN127B19876鞍型垫圈DIN128A19877弹簧止动垫圈DIN137A19878波形弹垫DIN137B19879外舌止动垫圈DIN432198310小垫圈DIN433199011方斜垫圈（U型）DIN434199012方斜垫圈（I型）DIN435198913方垫圈DIN436199014木螺钉专用垫圈DIN440199015内舌止动垫圈DIN46216锁紧垫圈DIN470200817外齿锁紧垫圈DIN6797A198818内齿锁紧垫圈DIN6797I198819外锯齿锁紧垫圈DIN6798A198820内锯齿锁紧垫圈DIN6798I198821大垫圈DIN6916198922重型垫圈DIN7349197423圆柱头螺钉用弹簧垫圈DIN7980198724平垫DIN90211990八、挡圈类序号名称标准代号版本/年号备注1轴用弹性挡圈DIN47119812孔用弹性挡圈DIN47219813开口挡圈DIN679919814轴用钢丝挡圈DIN79931970九、销类序号名称标准代号版本/年号备注1开口销DIN9419832螺纹圆锥销DIN25819773圆柱销DIN6325十、铆钉类序号名称标准代号版本/年号备注1沉头实心铆钉DIN30219932半圆头铆钉DIN66019933半沉头铆钉DIN66119934大半圆头铆钉DIN67419935沉头铆钉DIN67519936铆钉用具DIN643419847盘头半空心铆钉DIN679119938沉头半空心铆钉DIN679219939开口型铆钉DIN73371991。

October 2000©No part of this translation may be reproduced without the prior permission ofDIN Deutsches Institut für Normung e.V., Berlin. Beuth Verlag GmbH, 10772Berlin, Germany, has the exclusive right of sale for German Standards (DIN-Normen).English price group06Sales No.010602.01Page 2DIN 1587:2000-10DIN EN ISO 3269Fasteners – Acceptance inspection (ISO/DIS 3269:1998)*)DIN EN ISO 3506-2Mechanical properties of corrosion-resistant stainless steel fasteners – Part 2: Nuts (ISO 3506-2:1997)DIN EN ISO 4042Fasteners – Electroplated coatings (ISO 4042:1999)DIN EN ISO 4759-1Tolerances for fasteners – Part 1: Bolts, screws, studs and fit bolts – Product grades A,B and C (ISO/DIS 4759-1:1997)*)DIN EN ISO 10683Fasteners – Non-electrically applied zinc flake coatings (ISO/DIS 10683:1999)*)ISO 8992:1986Fasteners – General requirements for bolts, screws, studs and fit bolts3Dimensions Nut dimensions shall be as given in figures 1 and 2 and table 1.*) Currently at draft stage.m w is the minimum wrenching height.Figure 1:Nut dimensions for sizes up to M10 (notation)15°to 30°r (s ph e r i c a l )Other dimensions as in figure 1.Figure 2:Nut dimensions for sizes M12 and above (notation)(with thread undercut)Page3DIN 1587:2000-10Table 1:Nut dimensionsPage 4DIN 1587:2000-104Technical delivery conditionsTable 2:Technical delivery conditions5DesignationDesignation of a size M8 hexagon domed cap nut of property class 6:Nut DIN 1587 – M8 – 6The designation of sizes M10, M12, M14 and M22 nuts shall also include the width across flats.EXAMPLE:Designation of a size M12 hexagon domed cap nut of property class 6 and with a width across flats of 18 mm (SW18):Nut DIN 1587 – M12 – SW18 – 6If cap nuts for thread sizes up to M10 are to be supplied with thread undercut, the symbol Ri shall be included in the designation.EXAMPLE:Nut DIN 1587 – M8 – Ri – 6Where a specific product grade is required, the letter denoting the product grade shall be included in the designation.EXAMPLE:Nut DIN 1587 – M8 – 6 – A6MarkingNuts of grade CU3 or CU6 copper-zinc alloy are to be marked as specified in DIN EN 28839. For nuts of product grade A, the symbol (CU3 or CU6) shall be stamped on one of the hexagon flats, viz. in the middle of the flat and with the lettering parallel to the nut axis. For nuts of product grade B, the symbol shall be cast on, embossed or punched on the curved portion of the cap.MaterialSteel Stainless steel Nonferrous metal GeneralAs specified in ISO 8992.requirementsThread Tolerance6H As specified inDIN 13-15.Property class 1)6A1-50CuZn 2)Mechanical (material)properties As specified inDIN EN 20898-2 and DIN EN ISO 3506-2.DIN EN 28839.DIN EN ISO 898-6.Product gradeA or B, at the manufacturer’s discretion.As specified in DIN EN ISO 4759-1.As processed.Plain PlainDIN EN ISO 4042 applies with regard to electroplating.DIN EN ISO 10683 applies with regard to zinc flake coatings.Surface finish DIN 267-2 applies with regard to surface roughness.DIN EN 493 applies with regard to surface discontinuities.DIN 267-10 applies with regard to hot-dip galvanizing.Acceptance inspectionDIN EN ISO 3269 applies with regard to acceptance inspec-tion.1)The use of other materials or property classes or of a particular grade of material shall be subject to agreement.2)CU3 or CU6 grade copper-zinc alloy, at the manufacturer’s discretion.Limit deviations and geometricaltolerancesPage5DIN1587:2000-10 If cap nuts are to be supplied without this marking, this shall be indicated by including the symbol oK in the designation.EXAMPLE:Nut DIN 1587 – M8 – Cu6 – oKThe DIN 4000-2–7.1 tabular layout of article characteristics shall apply to nuts covered in this standard.。

德标、欧标、国际、国标对照表—— DIN EN ISO GB 对照表新德标旧德标 英文名 中文名 国标 DIN EN ISO 4014DIN 931-1 Hexagon head bolts - Product grades A and B(ISO 4014:1999) 六角头螺栓 GB/T 5782-2000 DIN EN ISO 4016DIN 601 Hexagon head bolts - Product grade C(ISO 4016:1999) 六角头螺栓 C 级 GB/T 5780-2000 DIN EN ISO 4017DIN 933 Hexagon head screws - Product grade A and B (ISO 4017:1999) 六角头螺栓 全螺纹 GB/T 5783-2000 DIN EN ISO 4018DIN 558 Hexagon head screws - Product grade C (ISO 4018:1999) 六角头螺栓 全螺纹 C 级 GB/T 5781-2000 DIN EN ISO 8676DIN 961 Hexagon head screws with metric fine pitch thread - Product grade A and B(ISO 8676:1999) 六角头螺栓 细牙 全螺纹 GB/T 5786-2000 DIN EN ISO 8765DIN 960 Hexagon head bolts with fine pitch thread - Product grades A and B(ISO 8765:1999) 六角头螺栓 细牙 GB/T 5785-2000 DIN EN ISO 4032DIN 934 Hexagon nuts,style 1-Product grades A and B(ISO: 4032:1999) 1型六角螺母 GB/T 6170-2000 DIN EN ISO 4033Hexagon nuts,style 2-Product grades A and B(ISO: 4033:1999) 2型六角螺母 GB/T 6175-2000 DIN EN ISO 4034DIN 555 Hexagon nuts - Product grade C (ISO 4034:1999) 六角螺母 C 级 GB/T 41-2000 DIN EN ISO 4035DIN 439-2 Hexagon thin nuts(chamfered)-Product grade A and B (ISO 4035:1999) 六角薄螺母 GB/T 6172.1-2000 DIN EN ISO 4036DIN 439-1 Hexagon thin nuts - Product grade B(unchamfered)(ISO 4036:1999) 六角薄螺母 无倒角 GB/T 6174-2000 DIN EN ISO 8673DIN 934| DIN 971-1 Hexagon nuts,style 1,with metric fine pitch thread - Product grades A and B (ISO 8673:1999) 1型六角螺母 细牙 GB/T 6171-2000 DIN EN ISO 8674DIN 971-2 Hexagon nuts,style 2,with metric fine pitch thread - Product grades A and B (ISO 8674:1999) 2型六角螺母 细牙 GB/T 6176-2000 DIN EN ISO 8675DIN 439-2 Hexagon thin nuts with metric fine pitch thread - Product grades A and B (ISO 8675:1999) 六角薄螺母 细牙 GB/T 6173-2000 DIN EN ISO 4762DIN 912 Hexagon socket head cap screws(ISO 4762:1997) 内六角圆柱头螺钉 GB/T 70.1-2000 DIN EN ISO 7380 Hexagon socket button head sxrews (ISO 7380:1997) 内六角平圆头螺钉GB/T 70.2-2000DIN EN ISO 10642DIN 7991 Hexagon socket countersunk head screws (ISO 10642:1997) 内六角沉头螺钉 GB/T 70.3-2000 DIN EN ISO 1207DIN 84 Slotted cheese head screws-Product grade A(ISO 1207:1992) 开槽圆柱头螺钉 GB/T 65-2000 DIN EN ISO 1580DIN 85 Slotted pan head screws-Product grade A(ISO 1580:1994) 开槽盘头螺钉 GB/T 67-2000 DIN EN ISO 2009DIN 963 Slotted countersunk flat head screws(common head style)(ISO 2009:1994) 开槽沉头螺钉 GB/T 68-2000 DIN EN ISO 2010DIN 964 Countersunk slotted raised head screws(common head style)-Produce grade A(ISO 2010:1994) 开槽半沉头螺钉 GB/T 69-2000 DIN EN ISO 7045DIN 7985 Pan head screws with type H or type Z cross recess-Product grade A(ISO 7054:1994) 十字槽盘头螺钉 GB/T 818-2000 DIN EN ISO 7046-1DIN 965 Countersunk flat head screws (common head style)with type H or type Z cross recess,product grade A-Part 1:Steel of property class 4.8(ISO 7046-1:1994) 十字槽盘头螺钉 第1部分：钢4.8级 GB/T 819.1-2000 DIN EN ISO 7046-2DIN 965 Cross recessed countersunk flat head screws (common head style),product grade A-Part2:Steel of property class 8.8,stainless steel and nonferous metals(ISO 7046-2:1990) 十字槽沉头螺钉 第2部分：钢8.8、不锈钢A2-70和有色金属CU2或CU3 GB/T 819.2-1997 DIN EN ISO 7047DIN 966 Countersunk raised head screws (common head style) with type H or type Z cross recess-Product grade A(ISO 7047:1994) 十字槽半沉头螺钉 GB/T 820-2000 DIN EN ISO 7048Cross recessed cheese head screws (ISO 7048:1998) 十字槽圆柱头螺钉 GB/T 822-2000 DIN EN ISO 10644Screw and washer assemblies with plain washers-Washer hardness classes 200HV and 300HV(ISO 10644:1998) 螺栓或螺钉和平垫圈组合件 GB/T 9074.1-2002 DIN EN ISO 10510Tapping screw and washer assemblies with plain washers(ISO 10510l:1999) 自攻螺钉和平垫圈组合件 GB/T 9074.18-2002 IDN EN ISO 15480Hexagon washer head drilling screws with tapping screws thread (ISO 15480:1999) 六角凸缘自钻自攻螺钉 GB/T 15856.5-2002 IDN EN ISO 15481Cross recessed pan head drilling screws with tapping screw thread(ISO 15481:1999) 十字槽盘头自钻自攻螺钉 GB/T 15856.1-2002 IDN EN ISO 15482 Cross recessed countersunk head drilling screws with tapping screw thread (ISO 15482:1999) 十字槽沉头自钻自攻螺钉GB/T 15856.2-2002IDN EN ISO 15483Cross recessed raised countersunk head drilling screws with tapping screw thread(ISO 15483:1999) 十字槽半沉头自钻自攻螺钉 GB/T 15856.3-2002 DIN EN ISO 10669Plain washers for tapping screw and washer assemblies - Normal and large series - Product grade A （ISO 10669:1999) 平垫圈 用于自攻螺钉和垫圈组合件 GB/T 97.5-2002 DIN EN ISO 10673Plain washers for screw and washer assemblies - Small,normal and large series - Product grade A (ISO 10673:1998) 平垫圈 用于螺钉和垫圈组合件 GB/T 97.4-2002 DIN EN ISO 2338DIN 7 Parallel pins,of unhardened steel and austenitic stainless steel(ISO 2338:1997) 圆柱销 不淬硬钢和奥氏体不锈钢 GB/T 119.1-2000 DIN EN ISO 8733DIN 7979 Parallel pins whit internal thread,of unhardened steel and austenitic stainless steel(ISO 8733:1997) 内螺纹圆柱销 不淬硬钢和奥氏体不锈钢 GB/T 120.1-2000 DIN EN ISO 8734DIN 6325 Parallel pins,of hardened steel or martensitic stainless steel(Dowel pins)(ISO 8734:1997) 圆柱销 淬硬钢和马氏体不锈钢 GB/T 119.2-2000 DIN EN ISO 8735DIN 7979 Parallel pins with internal thread,of hardened steel and martensitic stainless steel(ISO 8735:1997) 内螺纹圆柱销 淬硬钢和马氏体不锈钢 GB/T 120.2-2000 DIN EN ISO 8748DIN 7344 Spring-type straight pins,coiled,heavy duty (ISO 8748:1997) 弹性圆柱销 卷制 重型 GB/T 879.3-2000 DIN EN ISO 8750DIN 7343 Spring-type straight pins,coiled,standard duty (ISO 8750:1997) 弹性圆柱销 卷制 标准型 GB/T 879.4-2000 DIN EN ISO 8751Spring-type straight pins,coiled,light duty （ISO 8751:1997) 弹性圆柱销 卷制 轻型 GB/T 879.5-2000 DIN EN ISO 8752DIN 1481 Spring-type straight pins,slotted,heavy duty (ISO 8752:1997) 弹性圆柱销 直槽 重型 GB/T 879.1-2000 DIN EN ISO 13337DIN 7346 Spring-type straight pins,slotted,light duty (ISO 13337:1997) 弹性圆柱销 直槽 轻型 GB/T 879.2-2000 DIN EN ISO 1234DIN 94 Split pins （ISO1234:1997) 开口销 GB/T 91-2000 DIN EN ISO 7089Plain washers-Normal series-Product grade A 平垫圈 A 级 GB/T 97.1-2002 DIN EN ISO 7090Plain washers,chamfered-Normal series-Product grade A(ISO 7090:2000) 平垫圈 倒角型 A 级 GB/T 97.2-2002 DIN EN ISO 7091Plain washers-Normal series-Product grade C(ISO 7091:2000) 平垫圈 C 级 GB/T 95-2002 DIN EN ISO 7092 Plain washers-Small series-Product grade A(ISO 7092:2000)小垫圈 A 级 GB/T 848-2002DIN EN ISO 7093-1 Plain washers-Large series-Part 1: Product grade A(ISO 70931-1:2000)大垫圈 A 级 GB/T 96.1-2002DIN EN ISO 7093-2Plain washers-Normal series-Part 3: Product grade C(ISO 70936-2:2000) 大垫圈 C 级 GB/T 96.2-2002 DIN EN ISO 7094Plain washers-Extra large series -Product grade C(ISO 7094:2000) 特大垫圈 C 级 GB/T 5287-2002 DIN EN ISO 7040DIN 982| DIN 6924 Prevailing torque type hexagon nuts (with non-metallic insert),style 1 - Property classes 5,8 and 10(ISO 7040:1997) 1型非金属嵌件六角锁紧螺母 GB/T 889.1-2000 DIN EN ISO 7042DIN 980| DIN 6925 Prevailing torque type all-metal hexagon nuts,style 2 - Property classes 5,8, 10 and 12(ISO 7042:1997) 2型全金属六角锁紧螺母 GB/T 6185.1-2000 DIN EN ISO 7719Prevailing torque type all-metal hexagon nuts,style 1- Property classes 5,8 and 10(ISO 7719:1997) 1型全金属六角锁紧螺母 GB/T 6184-2000 DIN EN ISO 10511DIN 985 Prevailing torque type hexagon thin nuts (with non-metallic insert )(ISO 10511:1997) 非金属嵌件六角锁紧薄螺母 GB/T 6072.2-2000 DIN EN ISO 10512DIN 982| DIN 6924 Prevailing torque type hexagon nuts (with non-metallic insert),style 1,with metric fine pitch thread-Property classes 6,8 and 10(ISO 10512:1997) 1型非金属嵌件六角锁紧螺母 细牙 GB/T 889.2-2000 DIN EN ISO 10513 DIN 980|DIN 6925 Prevailing torque type all-metal hexagon nuts,style 2,with metric fine pitch thread - Property classes 8,10 and 12(ISO 10513:1997)2型全金属六角锁紧螺母 细牙GB/T 6185.2-2000原汁原味的德标 DIN (ISO、EN)、美标 IFI (ANSI, ASME, SAE)、公制美标、日标 JIS 资料！。

ICS 21.060.20Sechskant-SchweißmutternDEUTSCHE NORM January 2000929{Continued on pages 2 to 5.©No part of this translation may be reproduced without the prior permission ofDIN Deutsches Institut für Normung e.V., Berlin. Beuth Verlag GmbH , 10772Berlin, Germany,has the exclusive right of sale for German Standards (DIN-Normen).Translation by DIN-Sprachendienst.In case of doubt, the German-language original should be consulted as the authoritative text.Hexagon weld nutsRef.No.DIN 929:2000-01English price group 06Sales No.010606.00SupersedesFebruary 1998 edition.In keeping with current practice in standards published by the International Organization for Standardization (ISO), a comma has been used throughout as the decimal marker.ForewordThis standard has been prepared by Technical Committee Schrauben und Muttern mit Außenantrieb of the Normenausschuss Mechanische Verbindungselemente (Fasteners Standards Committee).In the December 1972 edition of this standard, nuts of property class 8 (‘weldable’) were specified. Since then, proof loads have been increased and new nut heights specified both in International and European Standards (cf. DIN EN 20898-2).I t did not seem advisable to adapt the nut heights to those of nuts with full loadability, since weld nut mounting is largely automated. Changing the nut dimensions would thus have given rise to considerable difficulties (retooling), which would not have been offset by the advantage of a slightly higher resistance to stripping.Instead, this standard specifies steel with a maximum carbon content of 0,25 % and proof loads which are deemed sufficient for weld nuts to be used together with bolts of property classes lower than 8.8. Weld nuts with a higher loadability are specified in DIN 977.The DIN 4000-2-9.4 tabular layout of article characteristics shall apply to nuts covered in this standard.AmendmentsThis standard differs from the February 1998 edition as follows:a)Table 1 has been amended to include limit deviations for dimension h 2 for thread sizes M8 and M10.b)The designation of hexagon weld nuts with UNF thread has been specified.c)Some editorial amendments have been made.Previous editionsDIN 929: 1965-09, 1972-12, 1983-08, 1987-09, 1998-02.All dimensions are in millimetres.1ScopeThis standard specifies requirements for sizes M3 to M16 coarse and fine pitch thread hexagon weld nuts of product grade A, for use with bolts of property classes below 8.8 as specified in DIN EN ISO 898-1.Hexagon weld nuts with flange are specified in DIN 977.2Normative referencesThis standard incorporates, by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text, and the titles of the publications are listed below. For dated references, subsequent amendments to or revisions of any of these publications apply to this standard only when incorporated in it by amendment or revision. For undated references, the latest edition of the publication referred to applies.Page 2DIN 929:2000-01DIN 13-1General purpose ISO metric screw threads – Nominal sizes for 1 mm to 68 mm diameter coarse pitch threadsDIN 13-5General purpose ISO metric screw threads – Nominal sizes for 1 mm and 1,25 mm finepitch threads with diameters from 7,5 mm to 200 mmDIN 13-6General purpose ISO metric screw threads – Nominal sizes for 1,5 mm fine pitch threadswith diameters from 12 mm to 300 mmDIN 13-15ISO metric screw threads – Fundamental deviations and tolerances for screw threads of1 mm diameter and largerDIN 267-2Fasteners – Technical delivery conditions – Product grades and tolerances DIN 977Hexagon weld nuts with flange DIN 4000-2Tabular layouts of article characteristics for bolts, screws and fit bolts DIN EN 20898-2Mechanical properties of fasteners – Part 2: Nuts with coarse pitch thread and specifiedproof load values (ISO 898-2:1992)DIN EN ISO 898-1Mechanical properties of fasteners made of carbon steel and alloy steel – Part 1: Bolts,screws and studs (ISO 898-1:1999)DIN EN ISO 898-6Mechanical properties of fasteners – Part 6: Nuts with fine pitch thread and specifiedproof load values (ISO 898-6:1994)DIN EN ISO 3269Fasteners – Acceptance inspection (ISO/DIS 3269:1998)*)DIN EN ISO 4042Fasteners – Electroplated coatings (ISO 4042:1999)DIN EN ISO 4759-1Tolerances for fasteners – Part 1: Bolts, screws, studs and fit bolts – Product grades A,B andC (ISO/DIS 4759-1:1997)*)ISO 8992:1986Fasteners – General requirements for bolts, screws, studs and fit bolts ANSI B1.1-1989Unified inch screw threads (UN and UNR thread form)1)3DimensionsThe design shown is for illustrative purposes only, but the dimensions of nuts shall be as specified.Figure 1:Nut dimensions (notation)*) Currently at draft stage.1) Obtainable from Beuth Verlag GmbH (Auslandsnormen-Service), 10772 Berlin, Germany.Detail XDetail Y(sectional view)Page 3DIN 929:2000-01Table 1:Nut dimensionsThread sizebd 2d 3d 4e 1)d 1d 1 × P 2)Limit d11H13Max.Min.deviationsM3––0,84,54,53,158,15M4––0,8±0,2664,29,83M5––0,8775,2510,95M6––0,9±0,22886,312,02M8M8 × 1–1±0,2510,510,58,415,38M10M10 × 1,25M10 × 11,2512,512,510,518,74––7/16-20 UNF-2B 3)1,25±0,312,513,511,718,74––7/16-20 UNF-2B 3)1,2513,513,511,720,91M12M12 × 1,25M12 × 1,51,2514,814,812,620,91(M14)(M14 × 1,5)–1,5±0,416,816,814,724,27M16M16 × 1,5–1,518,818,816,826,51Thread sizeh 1h 2m s Approx. mass,in kg, per d 1d 1 × P 2)h14h131000 unitsM3––0,550,2537,50,78M4––0,650,353,591,13M5––0,70,44101,73M6––0,750,45112,5M8M8 × 1–0,90,56,5145,27M10M10 × 1,25M10 × 11,150,658179,58––7/16-20 UNF-2B 3)1,150,65101712––7/16-20 UNF-2B 3)1,40,8101914M12M12 × 1,25M12 × 1,51,40,8101913,7(M14)(M14 × 1,5)–1,81112221,3(M16)(M16 × 1,5)–1,81132428,5Bracketed sizes should not be used.1)emin = 1,12s min .2)Thread pitch.3)Thread series to ANSI B1.1; only to be used for fastening of seat belts in motor vehicles.Limit de-viationsLimit de-viations 0–0,10–0,150–0,20–0,10–0,150–0,24Technical delivery conditions4.1General requirements General requirements for standardized bolts, screws, studs and nuts are specified in ISO 8992.4.2MaterialWeld nuts shall be made of steel with a maximum carbon content of 0,25 %. If a specific steel grade is required,this shall be agreed on ordering.Page 4DIN 929:2000-014.3DesignWeld nuts shall be of product grade A conforming to DIN EN ISO 4759-1 or DIN 267-2, with diameters and pitches in accordance with DIN 13-1 (coarse thread) or DIN 13-5 and DIN 13-6 (fine thread), tolerance class 6G to DIN 13-15 being permitted.4.4Mechanical propertiesIf the proof load test specified in DIN EN 20898-2 or DIN EN ISO 898-6 is carried out, the loads given in table 2 shall be used. In case of dispute, welding projections shall be removed prior to testing.4.5Surface finishAs a rule, hexagon weld nuts are to be supplied uncoated. Electroplated coatings shall comply with the specifications given in DIN EN ISO 4042.Since uncoated weld nuts may be affected by corrosion during transit or storage, the manufacturer shall provide corrosion protection that does not impair nut weldability.4.6Acceptance inspectionAcceptance inspection shall comply with the specifications given in DIN EN ISO 3269.5DesignationDesignation of a size M10 hexagon weld nut made of steel (St):Nut DIN 929 – M10 – StI f a hexagon weld nut with UNF thread is to be supplied, the width across flats shall be included in the designation.EXAMPLE:Designation of a size 7/16-20 UNF-2B hexagon weld nut, made of steel (St), with a width across flats of 17 mm (SW17):Nut DIN 929 – 7/16-20 UNF-2B – SW17 – St6MarkingHexagon weld nuts of sizes M5 and above shall be imprinted with the manufacturer’s symbol.Table 2:Proof loadsCoarse threadProof load,Fine thread Proof load,(size)in N (size)in Nd 1d 1 ×PM33800––M46800––M511600––M615500––M828300M8×130200M1044800M10×150200––M10×1,2547800––7/16-20 UNF-2B 53600M1265300M12×1,2572100––M12×1,568200M1489700M14×1,597500M16123000M16×1,5132000Page 5DIN 929:2000-017Indication on drawingsFigure 2:Indication on drawings8Connecting dimensionsFigure 3:Connecting dimensions (nut not welded on)Table 3:Connecting dimensionsThread size as in table 1Plate thickness, a Hole diameter, d 5d 1d 1×PMin.Max.(H11)M3––0,631,54,5M4––0,751,56M5––0,8827M6––0,882,58M8M8×1–1310,5M10M10×1,25M10×11,25412,5––7/16-20UNF-2B 1,25413,5M12M12×1,25M12×1,51,5514,8M14M14×1,5–2616,8M16M16×1,5–2618,8。

101 DIN927 开槽无头轴肩螺钉 slotted shoulder screws102 DIN928 焊接方螺母 square weld nuts GB/T13680-92103 DIN929 焊接六角螺母 hexagon weld nuts GB/T13681-92104 DIN931 六角头螺栓（半牙） hexagon head screws ISO4014 GB5782-86105 DIN933 六角头螺栓（全牙）hexagon head screws ISO4017 GB5783-86106 DIN934 六角头螺母(1型) hexagon full nuts ISO4032 GB6170-86107 DIN934 细牙六角头螺母(1型) hexagon full nuts ISO8673 GB6171-86108 DIN935 开槽六角螺母 hexagon slotted and castle nuts ISO7035 GB6178-86109 DIN936 六角头薄螺母 hexagon thin nuts ISO4035 GB6172.1-86110 DIN937 六角头开槽薄螺母 hexagon thin slotted and castle nuts ISO7038 GB6181-86 111 DIN938 双头螺距（牙长=1D） studs metal (end=1d) GB897-88112 DIN939 双头螺距（牙长=1.25D） studs metal (end=1.25d) GB898-88113 DIN940 双头螺距（牙长=1.5D）studs metal (end=1.5d)114 DIN960 六角头细牙螺栓（半牙） hexagon head boltsmetric fine pitchthread ISO8765 GB5785-86115 DIN961 六角头细牙螺栓（全牙） hexagon head boltsmetric fine pitchthread ISO8676 GB5786-86116 DIN962 头部穿孔六角头螺栓 additional shapes and versions for bolts117 DIN963 开槽沉头螺钉 slotted countersund head screwsISO 2009 GB68-85118 DIN964 开槽半沉头螺钉 slotted raised countersunk oval head screwsISO2010 GB69-85119 DIN965 十字槽沉头螺钉 cross recessed countersunk headscrews ISO7046 GB819-85120 DIN966 十字槽半沉头螺钉 cross recessed raised countersunk headscrews ISO7047 GB820-85121 DIN970 六角头螺母 hexagon nuts type-1122 DIN971 六角头螺母 hexagon nuts type-2123 DIN972 细牙六角头螺母(2型) hexagon nuts with fine thread ISO8674 GB6176-86 124 DIN975 牙条(全螺纹) threaded rods(studdings) GB15389-94125 DIN976 螺纹销 threaded pins(stud bolts)126 DIN979 六角头开槽薄螺母（2型） hexagon thin slotted and castle nuts127 DIN980 全金属六角锁紧螺母（1型） prevailling torque type hexagon nutsall metall nuts ISO7199 GB6184-86128 DIN981 圆螺母 locknuts ISO2982 GB812-88129 DIN982 六角头尼龙锁紧螺母 prevailling torque type hexagon nutsheavy type with nylon insert ISO7040 GB889.1-86130 DIN985 六角头薄型尼龙锁紧螺母 prevailling torque type hexagon nutsheavy type with nylon insert ISO10511 GB6172.2-86131 DIN986 六角盖型尼龙锁紧螺母 prevailling torque typedomed capnuts with nylon insert132 DIN988 配合垫片shim rings133 DIN1052 木材连接用垫片 washers for timber connectors134 DIN1151 沉头钢钉 round plain head nails135 DIN1440 销钉专用垫片A型 plain washers for clevis pins(A型) ISO8738136 DIN1441 销钉专用垫片 plain washers for clevis pins137 DIN1444 带头销钉 clevis pins with head ISO2341138 DIN1471 圆锥型槽销 grooved pinstaper grooved ISO8744 GB/T13829.2139 DIN1472 圆锥型槽销(半槽)grooved pinstaper grooved halflength ISO8745 GB/T13829.2140 DIN1473 平行槽销(带倒角) grooved pinsparallel grooved full length ISO8740 141 DIN1474 前端凹槽槽销 grooved pinsreserve grooved half length ISO8741142 DIN1475 中部凹槽槽销 grooved pinscentre grooved ISO8742143 DIN1476 圆头槽销 grooved pins with round head ISO8746 GB/T13829.3144 DIN147 7沉头槽销 grooved pins with countersunk head ISO8747145 DIN1479 六角螺母棒turnuckles(centre parts)made out of hexagon bar146 DIN1480 花篮螺栓 turnuckles with eye bolt and hook bolt147 DIN1481 弹性圆柱销 spring pinsheavy type ISO8752 GB879-86148 DIN1587 组合式盖型螺母 hexagon domed cap nuts GB802-88149 DIN1804 开槽圆螺母（配合沟头扳手） slotted round nuts for hook spanner 150 DIN1816 圆螺母（带插销孔） round nuts with set holes151 DIN2093 盘型弹簧垫圈disc springs152 DIN3017 喉箍 hose clamps153 DIN3404 润滑油嘴（旋扭头） lubricating nipplesbutton head154 DIN3567 管夹shackles for conduilts155 DIN3570 U型螺栓 stirrup bolts(U-bolts)156 DIN6319 球面垫圈 spherical washersconical seats GB849-88157 DIN6325 圆柱销 parallel pins ISO8734158 DIN6330 厚六角螺母 hexagon nuts 1.5d GB56-88159 DIN6331 厚六角法兰面螺母 hexagon nuts 1.5d with collar GB6177-86160 DIN6334 长六角螺母 hexagon nuts 3d。

nur mit Genehmigung des DIN Deutsches Institut für Normung e.V.,Berlin,gestattet.Alleinverkauf der Normen durch Beuth Verlag GmbH,10772Berlin Preisgr.06Vertr.-Nr.00061AnwendungsbereichDiese Norm legt Anforderungen für niedrige Sechskant-Hutmuttern mit Metrischem Gewinde (Regel-und Feingewinde)von 4mm bis 72mm Gewinde-Nenndurchmesser in der Produktklasse A fest.2Normative VerweisungenDiese Norm enthält durch datierte oder undatierte Verweisungen Festlegungen aus anderen Publikationen.Diese normati-ven Verweisungen sind an den jeweiligen Stellen im T ext zitiert,und die Publikationen sind nachstehend aufgeführt.Bei datierten Verweisungen gehören spätere ¾nderungen oder Überarbeitungen dieser Publikationen nur zu dieser Norm,falls sie durch ¾nderung oder Überarbeitung eingearbeitet sind.Bei undatierten Verweisungen gilt die letzte Ausgabe der in Bezug genommenen Publikation.DIN 13-15Metrisches ISO-Gewinde ÐGrundabmaûe und T oleranzen für Gewinde ab 1mm Durchmesser DIN 76-1Gewindeausläufe ÐGewindefreistiche für Metrisches ISO-Gewinde nach DIN 13DIN 267-2Mechanische Verbindungselemente ÐT echnische Lieferbedingungen ÐAusführung und Maûgenauigkeit DIN 267-10Mechanische Verbindungselemente ÐT echnische Lieferbedingungen ÐFeuerverzinkte T eile DIN 4000-2Sachmerkmal-Leisten ÐT eil 2:Schrauben und MutternDIN EN 493Verbindungselemente ÐOberflächenfehler ÐMuttern ;Deutsche Fassung EN 493:1992DIN EN 20898-2Mechanische Eigenschaften von Verbindungselementen ÐT eil 2:Muttern mit festgelegten Prüfkräften ÐRegelgewinde (ISO 898-2:1992);Deutsche Fassung EN 20898-2:1993DIN EN 28839Mechanische Eigenschaften von Verbindungselementen ÐSchrauben und Muttern aus Nichteisenmetallen (ISO 8839:1986);Deutsche Fassung EN 28839:1991DIN EN ISO 898-6Mechanische Eigenschaften von Verbindungselementen ÐT eil 6:Muttern mit festgelegten Prüfkräften ÐFeingewinde (ISO 898-6:1994);Deutsche Fassung EN ISO 898-6:1995E DIN EN ISO 3269Mechanische Verbindungselemente ÐAnnahmeprüfung ;Identisch mit ISO/DIS 3269:1998;Deutsche Fassung prEN ISO 3269:1998DIN EN ISO 3506-2Mechanische Eigenschaften von Verbindungselementen aus nichtrostendenStählenÐT eil 2:Muttern(ISO 3506-2:1997);Deutsche Fassung EN ISO 3506-2:1997DIN EN ISO 4042Verbindungselemente ÐGalvanische Überzüge (ISO 4042:1999);Deutsche Fassung EN ISO 4042:1999E DIN EN ISO 4759-1T oleranzen für Verbindungselemente ÐT eil 1:Schrauben und Muttern,ProduktklassenA,BundC(ISO/DIS 4759:1997);Deutsche Fassung prEN ISO 4759-1:1997E DIN EN ISO 10683Verbindungselemente ÐNichtelektrolytisch aufgebrachte Zinklamellenüberzüge (ISO/DIS 10683:1999);Deutsche Fassung prEN 10683:1999DIN ISO 272Mechanische Verbindungselemente ÐSchlüsselweiten für Sechskantschrauben und -mutternDIN ISO 8992Verbindungselemente ÐAllgemeine Anforderungen für Schrauben und Muttern ;Identisch mit ISO 8992:1986Seite 2DIN 917:2000-103MaûeMaûe siehe Bilder1und2und T abelle1Seite3 DIN917:2000-10m w Mindesthöhe für den SchlüsselangriffBild1:Sechskant-Hutmutter bis10mm Gewindedurchmesser(mit Gewindeauslauf oder Gewindefreistich nach Wahl desHerstellers)übrige Maûe wie Bild1Bild2:Sechskant-Hutmutter ab12mm Gewinde-Nenndurchmesser(mit Gewindefreistich)Seite 4DIN 917:2000-10Ta b e l l e 1:M a ûeSeite 5DIN 917:2000-10Ta b e l l e 1(a b g e s c h l o s s e n )4T echnische Lieferbedingungen5BezeichnungBezeichnung einer Hutmutter mit Gewinde M8und Festigkeitsklasse 6:Hutmutter DIN 917±M8±6Bei der Bezeichnung von Hutmuttern mit den Gewinden M10,M12,M14und M22ist die Schlüsselweite (SW)in der Bezeichnung anzugeben,z.B.SW18für M12:Hutmutter DIN 917±M12±SW18±6Wird für die Gröûen bis 10mm Gewinde-Nenndurchmesser ausdrücklich ein Gewindefreistich gewünscht,so ist das Kurz-zeichen Ri in die Bezeichnung einzufügen,z.B.:Hutmutter DIN 917±M8±Ri ±6Anhang A (informativ)Sachmerkmal-LeisteFür Muttern nach dieser Norm gilt Sachmerkmal-Leiste DIN 4000-2±7.1Seite 6DIN 917:2000-10T abelle 2:T echnische LieferbedingungenWerkstoff StahlNichtrostender Stahl NichteisenmetallAllgemeine Anforderungen Norm DIN ISO 8992GewindeT oleranz 6H NormDIN 13-15Mechanische EigenschaftenFestigkeitsklasse 1)(Werkstoff)M39:5,6>M39:nach Verein-barungM39:A1-50>M39:nach Verein-barungCuZn =Kupfer-Zink-Legierung 1)NormenDIN EN 20898-2DIN EN ISO 898-6DIN EN ISO 3506-2DIN EN 28839Grenzabmaûe,Form-und LagetoleranzenProduktklasse ANormE DIN EN ISO 4759-1Oberflächewie hergestellt blankblankFür galvanischen Oberflächenschutz gilt DIN EN ISO 4042.Für nichtelektrolytisch aufgebrachten Zinklamellenüberzug gilt E DIN EN ISO 10683.Für Feuerverzinkung gilt DIN 267-10.Für die Rauhtiefen der Oberflächen gilt DIN 267-2.Für die zulässigen Oberflächenfehler gilt DIN EN 493.AnnahmeprüfungFür die Annahmeprüfung gilt E DIN EN ISO 3269.1)Andere Festigkeitsklassen oder Werkstoffe oder eine bestimmte Werkstoffsorte,z.B.CU 3,nach Vereinbarung.。