TOSHIBATLCS-90 SeriesTMP90CH44The information contained here is subject to change without notice.The information contained herein is presented only as guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of TOSHIBA or others. These TOSHIBA products are intended for usage in general electronic equipments (office equipment, communication equipment, measuring equipment, domestic electrification, etc.) Please make sure that you consult with us before you use these TOSHIBA products in equip-ments which require high quality and/or reliability, and in equipments which could have major impact to the welfare of human life (atomic energy control, spaceship, traffic signal, combustion control, all types of safety devices, etc.). TOSHIBA cannot accept liability to any damage which may occur in case these TOSHIBA products were used in the mentioned equipments without prior consultation with TOSHIBA.CMOS 8–Bit Microcontrollers TMP90CH44N/TMP90CH44F1. Outline and CharacteristicsThe TMP90CH44 is a high-speed, high performance 8-bit microcontroller developed for application in the control of various devices.TMP90CH44, CMOS 8-bit microcontroller , integrates an 8-bit CPU, ROM, RAM, A/D converter , multi-function timer/event counter , general-purpose serial interface and slave functions in a single chip, and with which external program memory and data memory can be extended up to 48KB.TMP90CH44N is a device with a 64-pin shrink DIP . TMP90CH44F is a device with a 64-pin flat package.The following are the features of TMP90CH44:(1)Highly efficient instructions: 163 types of basic instructions, includingMultiplication, division, 16-bit arithmetic operations, bit manipulation instructions(2)Minimum instruction executing time: 250ns (at 16MHz oscillation frequency)(3)Built-in ROM: 16KB(4)Built-in RAM: 512 bytes (5)Memory expansionExternal program memory: 48KB External data memory: 48KB(6)Highly accurate 8-bit A/D converter (4 channels)(7)General-purpose serial interface (1 channel)With asynchronous mode and I/O interface mode (8)Multi-function 16-bit timer/event counter (1 channel)(9)8-bit timer (4 channels)(10)Stepping motor control and pattern generation ports (2 channels)(11)Input/Output ports: 54 pins (12)Slave function (13)Interrupt function: 12 internal, 3 external (14)Micro Direct Memory Access (DMA) function (4 channels)(15)Watchdog timer function(16)Standby function (3 HALT modes)元器件交易网元器件交易网TMP90CH44Figure 1. TMP90C844 Block DiagramTMP90CH442. Pin Assignment and FunctionsThe assignment of input/output pins for TMP90C844, their name and outline functions are described below.2.1 Pin AssignmentFigure 2.1 (1) shows pin assignment of the TMP90C844N.Figure 2.1 (1). Pin Assignment (Shrink DIP)TMP90CH44Figure 2.1 (2) shows the pin assignment of TMP90CH44F.Figure 2.1 (2). Pin Assignment (Flat Package)TMP90CH442.2 Pin Names and FunctionsThe names of input/output pins and their functions are summarized in T able 2.2.Table 2.2 (1/2)Pin Name No. of pins I/O or tristate FunctionP00 ~ P07 /AD0 ~ AD78I/O Port 0: Each bit can be set for input or output/Tristate Address/Data bus: Operates as an 8-bit bidirectional address bus or data bus when using external memory.P10 ~ P17 /A8 ~ A158I/O Port 1: An 8-bit I/O port. Each bit can be set for input or output./Output Address bus: Operates as an address bus (upper 8 bits) when using external memory.P20 ~ P27 /SB0 ~ SB7 /WAIT8(8)(1)I/OPort 2: Each bit can be set for input or output.Address bus: The upper 8 bits address bus for external memory./Input Wait: Input pin for connecting a memory or peripheral LSI with delayed access time.P30 ~ P378I/O Port 3: 8-bit I/O port which allows I/O selection on bit basis (with programmable pull-up resistor)./SWR(1)/Input Slave write: The strobe signal input to write data from the master processor./SRD(1)/Input Slave read: The strobe signal used by the master processor to read data./SCS(1)/Input Slave chip select: The chip select signal input from the master processor.C/D(1)Input Command/data: The command/data select signal input from the master processor./STA(1)/Output Status output: Used to report the slave bus status to the master processor.RxD(1)Input Receiver of serial data/SCLK(1)/I/O Serial clock/TxD(1)/Output Transmitter of serial dataP40 ~ P478I/O Port 4: 8-bit I/O port which allows I/O selection on bit basis (with programmable pull-up resistor)./TO1, 3, 4, 5(4)/Output Timer outputs 1, 3,4, and 5: Output ports for timer 0, or timer 1, timer 2, timer 3 and timer 4 (2 lines). /TI0, 2, 4, 5(4)/Input Timer inputs 0, 2, 4, and 5: Input ports for timer 0, or timer 1, timer 2 and timer 4 (2 lines)./INT0(1)/Input Interrupt request terminal 0: Interrupt request pin 0: Level/rise edge programmable interrupt request pin./INT1(1)/Input Interrupt request terminal 1: Interrupt request pin 1: Rise/fall edge programmable interrupt request pin./INT2(1)/Input Interrupt request terminal 2: Interrupt request pin 2: Rise edge interrupt request pin.P50 ~ P53 /AN0 ~ AN34InputPort 50 ~ 53: 1-bit output ports.Analog input: 4 analog inputs to A/D converter.P56 /RD 1OutputPort 56: A 1-bit output port.Read: Strobe signal output for reading external memory.元器件交易网TMP90CH44Table 2.2 (2/2)Pin name No. of pins I/O or tristate FunctionP57 /WR 1OutputPort 57: A 1-bit output port.Write: Strobe signal output for writing external memory.P60 ~ P63/M00 ~ M034I/O/OutputPort 6: 4 bit I/O port which allows I/O selection on bit basis.Stepping motor control port 0 or pattern generation port 0.P70 ~ P73/M10 ~ M134I/OOutputPort 7: 4 bit I/O port which allows I/O selection on bit basis.Stepping motor control port 0 or pattern generation port 1.ALE1Output Address latch enableCLK1Output Clock output: Generates clock pulse at 1/4 frequency of clock oscillation. It is pulled up internally during resetting.EA1Input External access: Connects with V CC pin in the TMP90C844 built ROM is used.RESET1Input Reset: Initializes the TMP90C844. (pull-up resistance is built-in).X1, X22I/O Crystal oscillator connection pinVREF1–Input of reference voltage to A/D converterAGND1–GND pin for A/D converterV CC1–Power supply (+5V +/- 10%)GND1–GND pin (0V)元器件交易网TMP90CH443. OperationThe following explains the TMP90CH44 functions and basic operations. The CPU functions and internal I/O functions of the TMP90CH44 are the same as the TMP90C844.Refer to the “TMP90C844” section concerning functions which are not explained in the following.3.1 CPUThe TMP90CH44 has an internal high performance 8-bit CPU.Refer to the book TLCS 90 Series CPU Core Architecture section concerning the CPU operation.3.2 Memory MapThe TMP90CH44 can provide a maximum 48K byte program and data memory.The program and data memories may be allocated to the address 0000H ~ FFFFH.(1)Built-in ROMThe TMP90CH44 has an internal 16K-byte ROM. ThisROM is located at addresses 0000H ~ 3FFFH. Programexecution starts from address 0000H after a resetoperation.Addresses 0008H ~ 0078H in the internal ROM area areused as the interrupt processing entry area.(2)Built-in RAMThe MP90CH44 contains a 512-byte built-in RAM which isallocated to the addresses FFC0H ~ FFBFH. The CPUcan also access some portions of the RAM (192 bytearea FF00H ~ FFBFH) using short instruction codes inthe direct addressing mode.Addresses of FF18H ~ FF78H this RAM area can beused as the parameter area for micro DMA process-ing. (This area can freely be used when the micro DMAfunction is not used.)(3)Built-in I/OThe TMP90CH44 uses 56 bytes of the address space asa built-in I/O area. The area is allocated to the addressesFFC0H ~ FFF7H. The CPU can access the built-in I/Ousing short instruction codes in the direct addressingmode.Figure 3.2 shows the memory map and the accessranges of the CPU for each addressing mode.TMP90CH44Figure 3.2. Memory MapTMP90CH44 4. Electrical CharacteristicsTMP90CH44N/TMP90CH44F4.1 Absolute Maximum RatingsSymbol Parameter Rating UnitV CC Power supply voltage-0.5 ~ + 7VV IN Input voltage-0.5 ~ V CC + 0.5VP D Power dissipation (Ta = 85°C)F 500mW N 600T SOLDER Soldering temperature (10s)260°CT STG Storage temperature-65 ~ 150°CT OPR Operating temperature-40 ~ 85°C4.2 DC CharacteristicsV CC = 5V ± 10% TA = -20 ~ 70°C (1 ~ 16MHz)Typical values are for TA = 25°C and Vcc = 5V.Symbol Parameter Min Max Unit Test Conditions V IL Input Low Voltage (P0)-0.30.8V–V IL1P1, P2, P3, P4, P5, P6, P7-0.30.3V CC V–V IL2RESET, P45 (INTO)-0.30.25V CC V–V IL3EA-0.30.3V–V IL4X1-0.30.2V CC V–V IH Input High Voltage (P0) 2.2V CC + 0.3V–V IH1P1, P2, P3, P4, P5, P6, P70.7V CC V CC + 0.3V–V IH2RESET, P45 (INTO)0.75V CC V CC + 0.3V–V IH3EA V CC - 0.3V CC + 0.3V–V IH4X10.8V CC V CC + 0.3V–V OL Output Low Voltage–0.45V I OL = 1.6mAV OHV OH1 V OH2Output High Voltage2.40.75V CC0.9V CC–VVVI OH = -400µAI OH = -100µAI OH = -20µAI DAR Darlington Drive Current(8 I/O pins) (Note)-0.1-3.5mAV EXT = 1.5VR EXT = 1.1kΩI LI Input Leakage Current0.02 (Typ)± 5µA0.0 ≤ Vin ≤ V CCI LO Output Leakage Current0.05 (Typ)± 10µA0.2 ≤ Vin ≤ V CC - 0.2I CC Operating Current (RUN)Idle 135 (Typ)1.5 (Typ)505mAmAtosc = 16MHzSTOP (TA = -20 ~ 70°C)STOP (TA = 0 ~ 50°C)0.2 (Typ)4010µAµA0.2 ≤ Vin ≤ V CC - 0.2V STOP Power Down Voltage (@STOP) 2.0 6.0V V IL2 = 0.2V CC, V IH2 = 0.8V CCR RST RESET Pull Up Register50150KΩ–CIO Pin Capacitance–10pF testfreq = 1MHzV TH Schmitt width RESET, P45)0.4 1.0 (Typ)V–元器件交易网TMP90CH44AC Measuring Conditions•Output level: High 2.2V/Low 0.8V, C L = 50pF(However, CL = 100pF for AD0 ~ 7, A8 ~ 15, ALE, RD, WR)•Input level: High 2.4V/Low 0.45V (AD0 ~ AD7)High 0.8V CC /Low 0.2V CC (excluding AD0 ~ AD7)4.3 AC CharacteristicsV CC = 5V ± 10% TA = -20 ~ 70 ° C (1 ~ 16MHz)SymbolParameterVariable12.5MHz Clock16MHz ClockUnitMinMaxMinMaxMinMaxt OSC Oscillation cycle ( = x)80100080–62.5–ns t CYC CLK Period 4x 4x 320–250–ns t WH CLK High width 2x - 40–120–85–ns t WL CLK Low width2x - 40–120–85–ns t AL A0 ~ 7 effective address → ALE fall 0.5x - 15–25–16–ns t LA ALE fall → A0 ~ 7 hold 0.5x - 15–25–16–ns t LL ALE Pulse width x - 40–40–23–ns t LC ALE fall RD/WR fall 0.5x - 30–10–1–ns t CL RD/WR → ALE rise0.5x - 20–20–11–ns t ACL A0 ~ 7 effective address → RD/WR fall x - 25–55–38–ns t ACH Upper effective address → RD/WR fall 1.5x - 50–70–44–ns t CA RD/WR fall → Upper address hold0.5x - 20–20–11–ns t ADL A0 ~ 7 effective address → Effective data input – 3.0x - 35–205–153ns t ADH Upper effective address → Effective data input – 3.5x - 55–225164164ns t RD RD fall → Effective data input – 2.0x - 50–110–75ns t RR RD Pulse width 2.0x - 40–120–85–ns t HRRD rise →Data hold 0–0–0–ns t RAE RD rise → Address enable x - 15–65–48–ns t WW WR pulse width 2.0x - 40–120–85–ns t DW Effective data →WR rise 2.0x - 50–110–75–ns t WD WR rise →Effective data hold 0.5x - 10–30–21–ns t ACKH Upper address →CLK fall 2.5x - 50–150–106–ns t ACKL Lower address →CLK fall 2.0x - 50–110–75–ns t CKHA CLK fall →Upper address hold 1.5x - 80–40–13–ns t CCK RD/WR →CLK fall x - 25–55–37–ns t CKHC CLK fall →RD/WR rise x - 60–20–2–ns t DCK Valid data CLK fall x - 50–30–12–ns t CWA RD/WR fall →Valid WAIT –x - 40–40–22ns t AWAL Lower address →Valid WAIT – 2.0x - 70–90–55ns t WAH CLK fall →Valid WAIT hold 0–0–0–ns t AWAH Upper address →Valid WAIT – 2.5x - 70–130–86ns t CPW CLK fall →Port Data Output –x + 200–280–262ns t PRC Port Data Input →CLK fall 200–200–200–ns t CPRCLK fall →Port Data hold100–100–100–ns元器件交易网4.4 A/D Conversion CharacteristicsV CC = 5V ± 10% TA = -20 ~ 70°Cf = 1 ~ 16MHzSymbol Parameter Condition Min Max Unit V REF Analog reference voltage Vcc - 1.5Vcc VccVA GND Analog reference voltage Vss Vss VssV AIN Analog input voltage range Vss–VccIREF Supply current for analog reference voltage–0.5 1.0mAError (Quantize error of ± 0.5 LSB not included)Total error(TA = 25°C, Vcc = V REF = 5.0V)––1.0LSB Total error–– 2.54.5 Zero-Cross CharacteristicsV CC = 5V ± 10% TA = -20 ~ 70°Cf = 1 ~ 16MHzSymbol Parameter Condition Min Max Unit V ZX Zero-cross detection input AC coupling C = 0.1µF1 1.8V AC P - PA ZX Zero-cross accuracy50/60Hz sine wave–135mVF ZX Zero-cross detection input frequency–0.041kHz4.6 Timer/ Counter Input Clock (TI0, TI2, and TI4)V CC = 5V ± 10% TA = -20 ~ 70°Cf = 1 ~ 16MHzSymbol ParameterVariable12.5MHz Clock16MHz ClockUnit Min Max Min Max Min Maxt VCK Clock cycle8x + 100–740–600–ns t VCKL Low clock pulse width4x + 40–360–290–ns t VCKH High clock pulse width4x + 40–360–290–ns4.7 Interrupt OperationV CC = 5V ± 10% TA = -20 ~ 70°Cf = 1 ~ 16MHzSymbol ParameterVariable12.5MHz Clock16MHz ClockUnit Min Max Min Max Min Maxt INTAL INT0 Low level pulse width4x–320–250–nst INTAH INT0 High level pulse width4x–320–250–nst INTBL INT1, INT2 Low level pulse width8x + 100–740–600–nst INTBH INT1, INT2 High level pulse width8x + 100–740–600–ns(2) SCLK Output Mode4.8 Serial Channel Timing - I/O Interface Mode (1) SCLK Input ModeV CC = 5V ± 10% TA = -20 ~ 70°Cf = 1 ~ 16MHzSymbolParameterVariable12.5MHz Clock16MHz ClockUnitMinMaxMinMaxMinMaxt SCY SCLK cycle16x – 1.28–1–µs t OSS Output Data →rising edge of SCLK t SCY /2 - 5x - 50–190–137–ns t OHS SCLK Rising Edge →output data hold 5x - 100–300–212–ns t HSR SCLK Rising Edge →input data hold 0–0–0–ns t SRDSCLK Rising Edge → effective data input–t SCY - 5x -5 0–780–587nsSymbolParameterVariable12.5MHz Clock16MHz ClockUnitMinMaxMinMaxMinMaxt SCY SCLK cycle (programmable)16x 8192x 1.28655.41512µs t OSS Output data → SCLK rising edge t SCY - 2x - 50–970–725–ns t OHS SCLK rising edge →output data hold 2x - 80–80–45–ns t HSR SCLK rising edge →input data hold 0–0–0–ns t SRDSCLK rising edge → effective data input–t SCY - 2x - 150–970–725ns4.9 Slave Bus Interface Timing: RD, WR Bus ModeV CC = 5V ± 10% TA = -20 ~ 70°Cf = 1 ~ 16MHzSymbolParameter MinMaxUnitT SAR C/D setup →SRD fall 20–ns T HRA SRD rise → C/D hold 5–ns T SCR SCS setup →SRD fall 0–ns T HRC SRD rise →SCS hold 0–ns T WRD SRD pulse width120–ns T ARD SRD fall →effective data output –80ns T VRB SRD rise →effective data hold 1085ns T SAW C/D setup →SWR fall 20–ns T HWA SWR rise →C/D hold 5–ns T SCW SCR setup →SWR fall 0–ns T HWC SWR rise →SCS hold 0–ns T WWR SWR pulse width120–ns T SBW effective data input →SWR rise 80–ns T HWBSWR rise →effective data hold10–nsSlave Bus Interface Timing: DS, R/W Bus ModeSymbol Parameter Min Max UnitT SAD C/D setup →DS fall20–nsT HDA DSrise→ C/D hold5–nsT SCD SCS setup →DS fall0–nsT HDC DS rise →SCS hold0–nsT SAD SCS setup →DS fall20–nsT HDA DS rise →R/W hold5–nsT WDS DS pulse width120–nsT ADS DS fall →effective data output–80nsT VDB DS rise →effective data hold1085nsT SBD Effective data input → DS rise80–nsT HDB DS rise →effective data hold10–nsSTA Change TimingX = 1/foscSymbol ParameterVariable16MHz ClockUnit Min Max Min Maxt RPH STA fall after Output Buffer is read–2x + 50–175ns t WPH STA rise after Input Buffer is written–2x + 50–175ns4.10 Timing Chart4.11 Timing Chart for I/O Interface Mode4.12 Timing Chart for Slave Bus Interface: RD, WR Bus Mode (1) Read Operation(2) Write Operation4.13 Timing Chart for Slave Bus Interface: DS, R/W Bus Mode (1) Read Operation(2) Write Operation。
MTMT00A08-1415034-19-1415043-17-1393163-37-1415043-1 8-1393163-3MTMT00A0..MT7874002-2017, Rev. © 2015 Tyco Electronics Corporation,a TE Connectivity Ltd. company Datasheets and product specification according to IEC 61810-1 and to be used only together with the ‘Definitions’ section.Datasheets and product data is subject to the terms of the disclaimer and all chapters of the ‘Definitions’ section, available at /definitionsDatasheets, product data, ‘Definitions’ sec-tion, application notes and all specifications are subject to change.1SCHRACKn Snap-on mounting on DIN-rail n Screw mountingn Pozidrive screws with rising clamp terminals n Logical layout of input-/output connections n White marking areaMT DIN-rail sockets with screw-type terminalsMT 78 750 MT3 DIN-rail socket with screw-type terminals, 11-pin MT 78 755 MT2 DIN-rail socket with screw-type terminals, 8-pinMT78 760 MT3 DIN-rail socket with screw-type terminals, 11-pinMT 78 740 MT3 DIN-rail socket with screw-type terminals, 11-pin MT 78 745 MT2 DIN-rail socket with screw-type terminals, 8-pinGeneral Purpose Relays AccessoriesAccessories Multimode Relay MTZF0235-BF0103-BS0414-AB S0414-ACF0103-BS0311-BB S0414-AAF0200-BS0366-ASocket system MT 78 740 and MT 78 745n 8/11 pin socket for MT2 / MT3n Double A2 screw for simple further connection of coil supplyZ Zb02-2017, Rev. 0217© 2015 Tyco Electronics Corporation, a TE Connectivity Ltd. company Datasheets and product specificationaccording to IEC 61810-1 and to be usedonly together with the ‘Definitions’ section.Datasheets and product data is subject to theterms of the disclaimer and all chapters ofthe ‘Definitions’ section, available at/definitionsDatasheets, product data, ‘Definitions’ sec-tion, application notes and all specificationsare subject to change.2SCHRACKType Part NumberMT 28 800Metal retaining clip MT 8-1393163-0LED and Protection modules for MT 78 740, MT 78 745Type Part NumberMTM T0 0A0Protection diode 1N4007 (A1+, A2-) 7-1393163-6MTM U0 730RC-network 110...230 VAC 7-1393163-8MTM L0 024red LED 24 VAC / VDC 7-1393163-4Function modules for MT 78 740, MT 78 745Type Part NumberMTM Z0 W00 Delay ON 7-1393163-9MTM F0 W00Multifunction 7-1393163-3Technical data - Function modulesNominal voltage 24...240 VDC / VACMains frequency 48...63 HzPrecision of time setting + 0.5 %Readiness for repetition ≤ 0.5 % or 5 msInfluence of temperature ≤ 0.1 %/°CTime range switchable 0.05s...240h in 8 rangesMaterial compliance: EU RoHS/ELV, China RoHS, REACH, Halogen contentrefer to the Product Compliance Support Center at/customersupport/rohssupportcenterAmbient temperature range -25…+55˚CGeneral Purpose RelaysAccessoriesAccessories Multimode Relay MT (Continued)ApprovalsVDE Cert. No. 40009096, cULus E135149Technical data MT78 750/755/760/740/745Rated voltage/Max. switching voltage AC 240/400 VACRated current 10 ADielectric strengthcoil-contact circuit 2500 V rmsopen contact circuit 1500 V rmsadjacent contact circuit 2500 V rmsClearance / creepage coil-contact circuit ≥ 2.8/4 mmMaterial group of insulation parts IIIaInsulation to IEC 60664-1Type of insulation coil-contact circuit basicopen contact circuit functionaladjacent contact circuits basicRated insulation voltage 250 VPollution degree 2Rated voltage system 230/400 VOvervoltage category IIIMaterial compliance: EU RoHS/ELV, China RoHS, REACH, Halogen contentrefer to the Product Compliance Support Center at/customersupport/rohssupportcenterAmbient temperature range -20…+80˚CTerminals screwTerminal screw torque acc. IEC 61984 0.5 Nmmax. 0.7 NmWire strip length 9 mmWire cross sectionsingle wire 2 x 2.5 mm2fine wire 2 x 2.5 mm2with bootlace crimp (DIN 46228/1) 2 x 1.5 mm2Insertion cycles A (10)Max. Insertion Force total 100 NMounting distance ≥ 0 mm, dense packingWeightMT 78 750/760 54 gMT 78 755 47 gMT 78 740 62 gMT 78 745 56 gPackaging unit 25 pcsDIN-rail sockets with screw-type terminalsType Part NumberMT 78 750DIN-rail socket with screw-type 1415035-1terminals, 11-pinMT 78 755DIN-rail socket with screw-type 3-1415035-1terminals, 8-pinMT 78 760DIN-rail socket with screw-type 8-1415034-1terminals, 11-pinMT 78 740DIN-rail socket with screw-type 8-1393163-3terminals, 11-pinMT 78 745DIN-rail socket with screw-type8-1393163-4F0201-BF0203-BF0204-B02-2017, Rev. 0117© 2015 Tyco Electronics Corporation, a TE Connectivity Ltd. company Datasheets and product specificationaccording to IEC 61810-1 and to be usedonly together with the ‘Definitions’ section.Datasheets and product data is subject to theterms of the disclaimer and all chapters ofthe ‘Definitions’ section, available at/definitionsDatasheets, product data, ‘Definitions’ sec-tion, application notes and all specificationsare subject to change.3SCHRACKFunction modules for MT 78 740, MT 78 745FunctionDelay ONDelay OFFsingle shot leading edgesingle shot trailing edgeDelay ONtriggerd by signal contactsingle shotflasher starting with pauseflasher starting with pulseAccessories Multimode Relay MT(Continued)Technical data MT78 602/603/612/613Rated voltage/Max. switching voltage AC 240/400 VACRated current 10 ADielectric strengthcoil-contact circuit 2500 V rmsopen contact circuit 1500 V rmsadjacent contact circuits 2500 V rmsClearance / creepage coil-contact circuit ≥ 2.8/4 mmMaterial group of insulation parts IIIaInsulation to IEC 60664-1Type of insulation coil-contact circuit basicopen contact circuit functionaladjacent contact circuits basicRated insulation voltage 250 VPollution degree 2Rated voltage system 230/400 VOvervoltage category IIIMaterial compliance: EU RoHS/ELV, China RoHS, REACH, Halogen contentrefer to the Product Compliance Support Center at/customersupport/rohssupportcenterAmbient temperature range -40…+70˚CTerminals pcb, solder terminalsInsertion cycles A (10)Max. Insertion Force total 100 NMounting distance ≥ 0 mm, dense packingResistance to soldering heat 270°C/10sWeight 7 gPackaging unit 25 pcsSockets with solder and PCB terminalsType Part NumberMT 78 612Socket 8-pin with solder terminals 7-1415043-1MT 78 613Socket 11-pin with solder terminals 8-1415043-1MT 78 602Socket 8-pin with PCB terminals 9-1415043-1MT 78 603Socket 11-pin with PCB terminals 1415044-1MT 78 613Socket 11-pin with solder terminalsMT 78 603Socket 11-pin with PCB terminalsF0107-AS0309-AAF0104-AS0309-ABF0105-AS0309-ACF0106-AS0309-ADGeneral Purpose RelaysAccessoriesMTMT00A08-1415034-19-1415043-17-1393163-37-1415043-1 8-1393163-3MTMT00A0..MT78740。
DMG80480F070_01WTR产品概述：●基于T5L0芯片，运行DGUS II系统。
●7寸，800*480分辨率，262K色，TN屏，普通视角。
●液晶屏与触摸屏框贴工艺，产品厚度仅5.1mm。
●COF结构，将智能屏的整个核心电路固定于液晶模组FPC上，适合结构要求轻、薄，成本要求苛刻，生产简单的应用。
●排线共50个pin脚，引出用户CPU核的IO、UART、CAN、AD、PWM等接口，二次开发十分方便。
Features:●Based on T5L0,running DGUS II system.●7inch,800*480pixels resolution,262K colors,TN-TFT-LCD,normal viewing angel.●LCD and TP frame lamination process,only5.1mm thickness.●COF structure.The entire core circuit of the smart screen is fixed on the FPC of LCM,featured by lightand thin structure,low cost and easy production.●50pins,including IO,UART,CAN,AD and PWM from user CPU core for easy secondary development.1外部接口External InterfacePIN 序号Definition 定义I/O Functional Description 功能描述1+5V I 供电输入，DC3.6-5.5V 。
Power supply,DC3.6-5.5V.2+5V I 3GND GND GND4GND GND 5GND GND 6AD7I 5路ADC 输入，3.3V 电源做为参考，12bit 分辨率，输入电压范围0-3.3V 。
