柴油机故障码汇总

上柴发动机故障列表闪码上柴发动机故障列表闪码..指示灯状态发动机静止（无故障）发动机静止（故障）发动机运行（无故障）发动机运行（故障）诊断开关关常亮常亮不亮常亮诊断开关开固定频率闪闪码固定频率闪闪码二、故障码的列表对不同车型的故障码有所不同，此故障码列表仅供参考，有所不同在所难免，使用中如有问题请与相关部门联系。

1 P0122 油门踏板传感器#1 信号过低22 完成测试2 P0123 油门踏板传感器#1 信号过高22 完成测试 3 P0222 油门踏板传感器#2 信号过低22 完成测试4 P0223 油门踏板传感器#2 信号过高22 完成测试 5 P0121 油门踏板传感器#1 常开22 完成测试6 P0221 油门踏板传感器#2 常开22 完成测试7 P0120 油门踏板传感器#1 常闭22 完成测试8 P0220 油门踏板传感器#2 常闭22 完成测试9 P2120 油门踏板传感器#1 和#2 信号无效22 完成测试10 P2163 怠速开关粘黏常开42 不具备条件测试11 P2109 怠速开关粘黏常闭42 不具备条件测试12 P0238 进气压力传感器信号过高37 完成测试13 P0237 进气压力传感器信号过低37 完成测试14 P0236 进气压力传感器无效37 不具备条件测试15 P0227 PTO踏板传感器信号过低23 取消16 P0228 PTO踏板传感器信号过高23 取消17 P0193 共轨压力传感器信号过高67 完成测试18 P0192 共轨压力传感器信号过低67 完成测试19 P0191 共轨压力传感器信号恒值67 不具备条件测试20 P0563 蓄电池电压过高26 完成测试21 P0562 蓄电池电压过低26 完成测试22 P0118 水温传感器信号过高11 完成测试23 P0117 水温传感器信号过低11 完成测试24 P0183 油温传感器信号过高14 完成测试25 P0182 油温传感器信号过低14 完成测试26 P0113 大气温度传感器信号过高16 完成测试27 P0112 大气温度传感器信号过低16 完成测试28 P2229 大气压力传感器信号过高15 完成测试29 P2228 大气压力传感器信号过低15 完成测试30 P1143 怠速量大小信号过高44 不具备条件测试31 P1142 怠速量大小信号过低44 不具备条件测试32 P0617 起动机开关对电源短路45 不具备条件测试33 P0337 曲轴转角传感器无脉冲信号13 完成测试34 P0342 凸轮转角传感器无脉冲信号12 完成测试35 P0385 凸轮转角和曲轴转角传感器无脉冲信号13 完成测试36 P0503 车速传感器信号频率过高21 不具备条件测试37 P0502 车速传感器信号输入短路或开路21 不具备条件测试38 P0501 车速传感器信号无效21 不具备条件测试39 P1681 排气制动阀输出开路或对地短路28 不具备条件测试40 P1682 排气制动阀输出对电源短路28 不具备条件测试41 P2148 喷油器公共端COM1 对电源短路57 完成测试42 P2147 喷油器公共端COM1 对地短路57 完成测试43 P2146 喷油器公共端COM1 开路57 完成测试44 P2151 喷油器公共端COM2 对电源短路58 完成测试45 P2150 喷油器公共端COM2 对地短路58 完成测试46 P2149 喷油器公共端COM2 开路58 完成测试47 P0201 喷油器#1 电磁线圈开路51 完成测试48 P0205 喷油器#2 电磁线圈开路55 完成测试49 P0203 喷油器#3 电磁线圈开路53 完成测试50 P0206 喷油器#4 电磁线圈开路56 完成测试51 P0202 喷油器#5 电磁线圈开路52 完成测试52 P0204 喷油器#6 电磁线圈开路54 完成测试53 P0611 电容充电电路由于充电不足导致失效59 不具备条件测试54 P0200 电容充电电路由于充电过度导致失效59 不具备条件测试55 P0629 油泵电磁阀#1 对电源短路71 不具备条件测试56 P2634 油泵电磁阀#2 对电源短路72 不具备条件测试57 P0629 油泵电磁阀#1 和#2 对电源短路73 不具备条件测试58 P0628 油泵电磁阀#1 开路或对地短路71 完成测试59 P2633 油泵电磁阀#2 开路或对地短路72 完成测试60 P0628 油泵电磁阀#1 和#2 开路或对地短路73 完成测试61 P2635 供油泵过载76 不具备条件测试62 P1088 供油泵过压76 不具备条件测试63 P1266 供油泵无负荷77 不具备条件测试64 P0093 供油泵由于油泵泄漏失去负荷78 不具备条件测试65 P1089 共轨压力超过上限69 不具备条件测试66 P0088 共轨压力超过最高限制68 不具备条件测试67 P0301 汽缸#1 供油系统故障61 不具备条件测试68 P0302 汽缸#2 供油系统故障65 不具备条件测试69 P0303 汽缸#3 供油系统故障63 不具备条件测试70 P0304 汽缸#4 供油系统故障66 不具备条件测试71 P0305 汽缸#5 供油系统故障62 不具备条件测试72 P0306 汽缸#6 供油系统故障64 不具备条件测试73 P0219 发动机转速超速7 不具备条件测试74 P0541 预热继电器对地短路25 不具备条件测试75 P0542 预热继电器开路或对电源短路25 不具备条件测试76 P1530 停车开关粘黏常闭46 不具备条件测试77 P0217 冷却水温超过上限6 完成测试78 P0234 进气压力超过上限39 不具备条件测试79 P0299 进气压力低于下限39 不具备条件测试80 P1676 倒档开关开路或对地短路48 不具备条件测试81 P1677 倒档开关对电源短路48 不具备条件测试82 U0073 CAN#1 节点出错8 取消83 U1001 CAN#2 节点出错9 取消84 P0704 离合器开关电路失效41 不具备条件测试85 P0850 空挡开关电路失效47 取消86 P0263 F/D#1 回路被激活61 取消87 P0275 F/D#2 回路被激活65 取消88 P0269 F/D#3 回路被激活63 取消89 P0278 F/D#4 回路被激活66 取消90 P0266 F/D#5 回路被激活62 取消91 P0272 F/D#6 回路被激活64 取消92 U0121 与ABS连接的CAN 总线开路9 取消93 U0155 与仪表连接的CAN 总线开路9 取消94 P0686 主继电器粘黏常闭 5 不具备条件测试95 P1565 巡航开关电路失效43 不具备条件测试96 P1602 QR码没有写入 2 完成测试97 P0602 QR码错误2 完成测试98 P1601 QR码定义错误0 取消99 P0607 看门狗IC故障导致CPU 故障 3 不具备条件测试100 P0606 主CPU 故障导致CPU 故障3 不具备条件测试101 P0601 FLASH 校验和错误3 不具备条件测试。

附件2：潍柴发动机故障列表闪码表
潍柴动力国III柴油机
闪码表
Blink code can be displayed in three levels of blinking.
闪码以三位的形式显示
1. First level of blinking will classify an error specific to part of an system, for e.g. if error is because of ECU, Hydraulics,Sensors,
Actuatators
第一位将错误按系统分类，比如说一个错误是否是由ECU、液压部件、传感器、执行器引起的；
2. Second Level of Blinking will indicate details about component identified.
第二位表明发生错误的部件；
3. Third Level will uniquely identify the Fault Path.
第三位确定错误路径。

闪码按系统的基本分类
主机厂安装CAN总线以后，可能出现的闪码：
目前国三上没有用到的功能及传感器、执行器：。

卡特柴油机故障代码3512B柴油机故障代码表代码故障含义E009 海拔高度减少E038 低水温报警E012 曲轴箱压力减少E013 曲轴箱压力关断E101 曲轴箱压力报警E099 曲轴箱压力报警E095 柴油滤芯堵塞报警E043 低系统电压报警030 模块033 电控模块端口034 标准的电控模块036 主控模块047 次要模块76 检测控制器97 电子通讯模块091-08 油门信号输出不正常094-03 燃油压力信号不正常（对电池短路或开路）094-04 燃油压力信号不正常（对地短路）094-13 燃油压力传感器需校正096-03 燃油油位传感器不正常100-03 机油压力信号不正常100-04 机油压力信号不正常100-13 机油压力传感器需校正101-03 曲轴箱压力传感器信号不正常101-04 曲轴箱压力传感器信号不正常101-13 曲轴箱压力标定110-03 水温信号不正常110-04 水温信号不正常127-08 动力传动油压不正常168-00 电池电压高168-01 电池电压低168-02 电池间歇性断电172-08 空气进气温度不正常175-08 机油温度不正常177-08 功率系列温度不正常190-02 转速感应塞无信号190-03 转速感应塞不正常190-08 转速感应塞不正常248-02 卡特数据连接间断或不正常253-02 个性模块不相配294-12 电控模块故障261-13 需做定时标定262-03 模拟传感器电压不正常262-04 模拟传感器电压不正常263-03 数字传感器电压不正常263-04 数字传感器电压不正常268-02 程序参数错误271-03 现时报警271-05 现时报警271-06 现时报警273-03 涡轮增压器出口压力不正常273-04 涡轮增压器出口压力不正常273-13 涡轮增压器出口压力传感器需标定274-03 大气压力信号不正常274-04 大气压力信号不正常274-13 大气压力传感器需标定275-03 右涡轮增压器进气压力信号不正常275-04 右涡轮增压气进气压力信号不正常275-13 右涡轮增压器进气压力传感器需标定276-03 左涡轮增压器进气压力信号不正常276-04 左涡轮增压器进气压力信号不正常276-13 左涡轮增压器进气压力传感器需标定279-03 后冷器水温信号不正常279-04 后冷器水温信号不正常289-03 未过滤燃油压力传感器不正常289-04 未过滤燃油压力传感器不正常289-13 未过滤的燃油压力传感器需标定336-02 启动开关不正常337-02 紧急停车开关按钮不正常338-05 预润滑继电器不正常338-06 预润滑继电器不正常342-02 备用转速传感器故障342-03 备用转速传感器故障342-08 备用转速传感器故障444-03 启动马达继电器故障444-05 启动马达继电器故障444-06 启动马达继电器故障446-05 空气关断继电器故障446-06 空气关断继电器故障542-03 未过滤的机油压力传感器不正常542-04 未过滤的机油压力传感器不正常542-13 未过滤的机油压力传感器需标定545-05 乙醚启动继电器不正常545-06 乙醚启动继电器不正常546-05 乙醚保持继电器不正常546-06 乙醚保持继电器不正常562-09 不能与显示器模块通讯819-02 显示数据间断性不正常821-03 显示器供电不正常821-04 显示器供电不正常827-08 左涡轮增压器进排气温度不正常828-08 右涡轮增压器进排气温度不正常。

上柴发动机故障列表闪码WEIHUA system office room 【WEIHUA 16H-WEIHUA WEIHUA8Q8-上柴发动机故障列表闪码..指示灯状态发动机静止（无故障）发动机静止（故障）发动机运行（无故障）发动机运行（故障）诊断开关关常亮常亮不亮常亮诊断开关开固定频率闪闪码固定频率闪闪码二、故障码的列表对不同车型的故障码有所不同，此故障码列表仅供参考，有所不同在所难免，使用中如有问题请与相关部门联系。

1 P0122 油门踏板传感器#1 信号过低 22 完成测试 2 P0123 油门踏板传感器#1 信号过高 22 完成测试 3 P0222 油门踏板传感器#2 信号过低 22 完成测试 4 P0223 油门踏板传感器#2 信号过高22 完成测试 5 P0121 油门踏板传感器#1 常开 22 完成测试 6 P0221 油门踏板传感器#2 常开 22 完成测试 7 P0120 油门踏板传感器#1 常闭 22 完成测试 8 P0220 油门踏板传感器#2 常闭 22 完成测试 9 P2120 油门踏板传感器#1 和#2 信号无效 22 完成测试 10 P2163 怠速开关粘黏常开 42 不具备条件测试 11 P2109 怠速开关粘黏常闭 42 不具备条件测试 12 P0238 进气压力传感器信号过高 37 完成测试 13 P0237 进气压力传感器信号过低37 完成测试 14 P0236 进气压力传感器无效 37 不具备条件测试 15 P0227 PTO踏板传感器信号过低 23 取消16 P0228 PTO踏板传感器信号过高 23 取消 17 P0193 共轨压力传感器信号过高 67 完成测试 18 P0192 共轨压力传感器信号过低 67 完成测试 19 P0191 共轨压力传感器信号恒值 67 不具备条件测试 20 P0563 蓄电池电压过高 26 完成测试 21 P0562 蓄电池电压过低 26 完成测试22 P0118 水温传感器信号过高 11 完成测试 23 P0117 水温传感器信号过低 11 完成测试 24 P0183 油温传感器信号过高 14 完成测试 25 P0182 油温传感器信号过低14 完成测试 26 P0113 大气温度传感器信号过高 16 完成测试 27 P0112 大气温度传感器信号过低 16 完成测试28 P2229 大气压力传感器信号过高 15 完成测试 29P2228 大气压力传感器信号过低 15 完成测试 30 P1143 怠速量大小信号过高 44 不具备条件测试 31 P1142 怠速量大小信号过低 44 不具备条件测试 32 P0617 起动机开关对电源短路 45 不具备条件测试 33 P0337 曲轴转角传感器无脉冲信号 13 完成测试 34 P0342 凸轮转角传感器无脉冲信号 12 完成测试 35 P0385 凸轮转角和曲轴转角传感器无脉冲信号 13 完成测试 36 P0503 车速传感器信号频率过高 21 不具备条件测试 37 P0502 车速传感器信号输入短路或开路 21 不具备条件测试 38 P0501 车速传感器信号无效 21 不具备条件测试 39 P1681 排气制动阀输出开路或对地短路 28 不具备条件测试 40 P1682 排气制动阀输出对电源短路 28 不具备条件测试 41 P2148 喷油器公共端COM1 对电源短路 57 完成测试 42 P2147喷油器公共端COM1 对地短路 57 完成测试 43 P2146喷油器公共端COM1 开路 57 完成测试 44 P2151 喷油器公共端COM2 对电源短路 58 完成测试 45 P2150 喷油器公共端COM2 对地短路 58 完成测试 46 P2149 喷油器公共端COM2 开路 58 完成测试 47 P0201 喷油器#1 电磁线圈开路 51 完成测试 48 P0205 喷油器#2 电磁线圈开路 55 完成测试 49 P0203 喷油器#3 电磁线圈开路 53 完成测试 50 P0206 喷油器#4 电磁线圈开路 56 完成测试 51 P0202 喷油器#5 电磁线圈开路 52 完成测试 52 P0204 喷油器#6 电磁线圈开路 54 完成测试 53 P0611 电容充电电路由于充电不足导致失效 59 不具备条件测试 54 P0200 电容充电电路由于充电过度导致失效59 不具备条件测试 55 P0629 油泵电磁阀#1 对电源短路71 不具备条件测试 56 P2634 油泵电磁阀#2 对电源短路72 不具备条件测试 57 P0629 油泵电磁阀#1 和#2 对电源短路 73 不具备条件测试 58 P0628 油泵电磁阀#1 开路或对地短路 71 完成测试 59 P2633 油泵电磁阀#2 开路或对地短路 72 完成测试 60 P0628 油泵电磁阀#1 和#2 开路或对地短路 73 完成测试 61 P2635 供油泵过载76 不具备条件测试 62 P1088 供油泵过压 76 不具备条件测试 63 P1266 供油泵无负荷 77 不具备条件测试 64 P0093 供油泵由于油泵泄漏失去负荷 78 不具备条件测试65 P1089 共轨压力超过上限 69 不具备条件测试 66P0088 共轨压力超过最高限制 68 不具备条件测试 67P0301 汽缸#1 供油系统故障 61 不具备条件测试 68P0302 汽缸#2 供油系统故障 65 不具备条件测试 69P0303 汽缸#3 供油系统故障 63 不具备条件测试 70P0304 汽缸#4 供油系统故障 66 不具备条件测试 71P0305 汽缸#5 供油系统故障 62 不具备条件测试 72P0306 汽缸#6 供油系统故障 64 不具备条件测试 73P0219 发动机转速超速 7 不具备条件测试 74 P0541 预热继电器对地短路 25 不具备条件测试 75 P0542 预热继电器开路或对电源短路 25 不具备条件测试 76 P1530 停车开关粘黏常闭 46 不具备条件测试 77 P0217 冷却水温超过上限 6 完成测试 78 P0234 进气压力超过上限 39 不具备条件测试 79 P0299 进气压力低于下限 39 不具备条件测试 80 P1676 倒档开关开路或对地短路 48 不具备条件测试 81 P1677 倒档开关对电源短路 48 不具备条件测试 82 U0073 CAN#1 节点出错 8 取消 83 U1001 CAN#2 节点出错 9 取消 84 P0704 离合器开关电路失效41 不具备条件测试 85 P0850 空挡开关电路失效 47 取消 86 P0263 F/D#1 回路被激活 61 取消 87 P0275F/D#2 回路被激活 65 取消 88 P0269 F/D#3 回路被激活 63 取消 89 P0278 F/D#4 回路被激活 66 取消 90 P0266 F/D#5 回路被激活 62 取消 91 P0272 F/D#6 回路被激活 64 取消 92 U0121 与ABS连接的CAN 总线开路 9 取消 93 U0155 与仪表连接的CAN 总线开路 9 取消 94 P0686 主继电器粘黏常闭 5 不具备条件测试 95 P1565 巡航开关电路失效 43 不具备条件测试 96 P1602 QR码没有写入 2 完成测试 97 P0602 QR码错误 2 完成测试 98 P1601 QR码定义错误 0 取消 99 P0607 看门狗IC故障导致CPU 故障 3 不具备条件测试 100 P0606 主CPU 故障导致CPU 故障 3 不具备条件测试 101P0601 FLASH 校验和错误 3 不具备条件测试。

0xa2,0x01,0x00,0x14,"0002","来自CAN的空调信号超时"0xa2,0x01,0x00,0x18,"0003","来自CAN的空调信号不可信"0xa2,0x01,0x00,0x21,"0010","模数转换器参考电压超出上限门槛值"0xa2,0x01,0x00,0x22,"0011","模数转换器参考电压低于下限门槛值"0xa2,0x01,0x00,0x24,"0012","模数转换器测试脉冲电压高出门槛值"0xa2,0x01,0x00,0x28,"0013","一定时间内只有部分数据流被转换"0xa2,0x01,0x00,0x31,"0020","HFM传感器进气温度电压值超出上限门槛值"0xa2,0x01,0x00,0x32,"0021","HFM传感器进气温度电压值低于下限门槛值"0xa2,0x01,0x00,0x41,"0030","HFM传感器平均电压值超出上限门槛值"0xa2,0x01,0x00,0x42,"0031","HFM传感器平均电压值低于下限门槛值"0xa2,0x01,0x00,0x51,"0040","空气流量比超出上限门槛值"0xa2,0x01,0x00,0x52,"0041","空气流量比低于下限门槛值"0xa2,0x01,0x00,0x61,"0050","单元时间内的空气流量超出上限门槛值"0xa2,0x01,0x00,0x62,"0051","单元时间内的空气流量低于下限门槛值"0xa2,0x01,0x00,0x71,"0060","油门踏板1电压值高出上限门槛值"0xa2,0x01,0x00,0x72,"0061","油门踏板1电压值低于下限门槛值"0xa2,0x01,0x00,0x74,"0062","油门踏板1与油门踏板2的两倍的信号关系不可信" 0xa2,0x01,0x00,0x81,"0070","油门踏板2电压值高出上限门槛值"0xa2,0x01,0x00,0x82,"0071","油门踏板2电压值低于下限门槛值"0xa2,0x01,0x00,0x84,"0072","油门踏板2与油门踏板1的1/2的信号关系不可信" 0xa2,0x01,0x00,0x91,"0080","大气压力传感器电压高出上限门槛值"0xa2,0x01,0x00,0x92,"0081","大气压力传感器电压低于下限门槛值"0xa2,0x01,0x00,0x94,"0082","来自CAN的大气压力传感器信号不可信"0xa2,0x01,0x00,0x98,"0083","大气压力传感器与进气压力传感器信号不可信"0xa2,0x01,0x00,0xa1,"0090","车速限制指示灯电源短路"0xa2,0x01,0x00,0xa2,"0091","车速限制指示灯电源短路"0xa2,0x01,0x00,0xa4,"0092","车速限制指示灯没有信号"0xa2,0x01,0x00,0xa8,"0093","车速限制指示灯超外温"0xa2,0x01,0x00,0xb8,"00a3","油门与刹车信号不可信"0xa2,0x01,0x00,0xc1,"00b0","进气量调节器正偏差超过上限门槛值"0xa2,0x01,0x00,0xd2,"00c1","进气量调节器负偏差低于下限门槛值"0xa2,0x01,0x00,0xe1,"00d0","进气加热常开故障"0xa2,0x01,0x00,0xf1,"00e0","进气加热器开时电压高于上限门槛值"0xa2,0x01,0x00,0xf2,"00e1","进气加热器开时电压低于下限门槛值"0xa2,0x01,0x01,0x01,"00f0","进气加热器闭时电压高于上限门槛值"0xa2,0x01,0x01,0x02,"00f1","进气加热器闭时电压低于下限门槛值"0xa2,0x01,0x01,0x11,"0100","进气加热器对电源短路"0xa2,0x01,0x01,0x12,"0101","进气加热器对地短路"0xa2,0x01,0x01,0x21,"0110","增压执行器电源短路故障"0xa2,0x01,0x01,0x32,"0121","增压执行器对地短路故障"0xa2,0x01,0x01,0x44,"0132","增压器没有信号"0xa2,0x01,0x01,0x48,"0133","增压器超温"0xa2,0x01,0x01,0x51,"0140","进气压力传感器电压超出上限门槛值"0xa2,0x01,0x01,0x52,"0141","进气压力传感器电压低于下限门槛值"0xa2,0x01,0x01,0x54,"0142","来自CAN的进气压力传感器信号不可信"0xa2,0x01,0x01,0x58,"0143","进气压力传感器与大气压力传感器信号不可信" 0xa2,0x01,0x01,0x61,"0150","电池电压原始值超出上限门槛"0xa2,0x01,0x01,0x62,"0151","电池电压原始值低于下限门槛"0xa2,0x01,0x01,0x74,"0162","来自CAN的刹车信号不可信"0xa2,0x01,0x01,0x78,"0163","刹车主、辅开关信号不可信"0xa2,0x01,0x01,0x81,"0170","中冷器旁通阀对电源短路"0xa2,0x01,0x01,0x82,"0171","中冷器旁通阀对地短路"0xa2,0x01,0x01,0x84,"0172","中冷器旁通阀没有信号"0xa2,0x01,0x01,0x91,"0180","冷却水水位传感器电压超出上限门槛值"0xa2,0x01,0x01,0x92,"0181","冷却水水位传感器电压低于下限门槛值"0xa2,0x01,0x01,0x94,"0182","冷却水位传感器开路"0xa2,0x01,0x01,0x98,"0183","冷却水水位传感器信号不可信"0xa2,0x01,0x01,0xa1,"0190","CRERCD电源短路"0xa2,0x01,0x01,0xa2,"0191","CRERCD地短路"0xa2,0x01,0x01,0xa4,"0192","CRERCD没有信号"0xa2,0x01,0x01,0xa8,"0193","CRERCD超温"0xa2,0x01,0x01,0xb1,"01a0","冷启动指示灯对电源短路"0xa2,0x01,0x01,0xb2,"01a1","冷启动指示灯对地短路"0xa2,0x01,0x01,0xb4,"01a2","没有冷启动指示灯信号"0xa2,0x01,0x01,0xb8,"01a3","冷启动指示灯超温"0xa2,0x01,0x01,0xc1,"01b0","冷却水温度传感器电压超出上限门槛"0xa2,0x01,0x01,0xc2,"01b1","冷却水温度传感器电压低于下限门槛"0xa2,0x01,0x01,0xc4,"01b2","来自CAN的冷却水温度传感器信号不可信"0xa2,0x01,0x01,0xc8,"01b3","冷却水温与油温信号不可信"0xa2,0x01,0x01,0xd8,"01c3","冷却水温在一定时间内没有达到最小值"0xa2,0x01,0x01,0xe8,"01d3","冷却水温在一定时间内上升幅度没有达到最小值" 0xa2,0x01,0x01,0xf1,"01e0","气缸1失火次数超过门槛值"0xa2,0x01,0x02,0x01,"01f0","气缸2失火次数超过门槛值"0xa2,0x01,0x02,0x11,"0200","气缸3失火次数超过门槛值"0xa2,0x01,0x02,0x21,"0210","气缸4失火次数超过门槛值"0xa2,0x01,0x02,0x31,"0220","气缸5失火次数超过门槛值"0xa2,0x01,0x02,0x41,"0230","气缸6失火次数超过门槛值"0xa2,0x01,0x02,0x51,"0240","多缸失火次数超过门槛值"0xa2,0x01,0x02,0x61,"0250","发动机控制单元内部错误"0xa2,0x01,0x02,0x71,"0260","压缩测试故障"0xa2,0x01,0x02,0x84,"0272","来自CAN的离合器信号不可信"0xa2,0x01,0x02,0x88,"0273","离合器状态信号不可信"0xa2,0x01,0x02,0x91,"0280","环境温度传感器电压超出上限门槛值"0xa2,0x01,0x02,0x92,"0281","环境温度传感器电压低于下限门槛值"0xa2,0x01,0x02,0x94,"0282","来自CAN的环境温度传感器信号不可信"0xa2,0x01,0x02,0xa1,"0290","环境温度传感器BET电压超出上限门槛值"0xa2,0x01,0x02,0xa2,"0291","环境温度传感器BET电压低于下限门槛值"0xa2,0x01,0x02,0xb1,"02a0","环境温度传感器CLgZn电压超出上限门槛值" 0xa2,0x01,0x02,0xb2,"02a1","环境温度传感器CLgZn电压低于下限门槛值" 0xa2,0x01,0x02,0xc1,"02b0","环境温度传感器InAir电压超出上限门槛值"0xa2,0x01,0x02,0xc2,"02b1","环境温度传感器InAir电压低于下限门槛值"0xa2,0x01,0x02,0xd8,"02c3","低怠速开关和刹车开关均激活并超过一段时间" 0xa2,0x01,0x02,0xe1,"02d0","EGR旁通阀对电源短路或超温"0xa2,0x01,0x02,0xe2,"02d1","EGR旁通阀对地短路"0xa2,0x01,0x02,0xe4,"02d2","没有EGR旁通阀信号"0xa2,0x01,0x02,0xf4,"02e2","车下启动/停止按钮卡住"0xa2,0x01,0x03,0x01,"02f0","排气管压力传感器电压超出上限门槛值"0xa2,0x01,0x03,0x02,"02f1","排气管压力传感器电压低于下限门槛值"0xa2,0x01,0x03,0x08,"02f3","排气管压力传感器信号不可信"0xa2,0x01,0x03,0x11,"0300","EGR对电源短路故障"0xa2,0x01,0x03,0x22,"0311","EGR对地短路故障"0xa2,0x01,0x03,0x34,"0322","没有EGR信号"0xa2,0x01,0x03,0x38,"0323","EGR超温"0xa2,0x01,0x03,0x41,"0330","只有凸轮轴信号,进入跛形回家状态"0xa2,0x01,0x03,0x51,"0340","没有凸轮轴信号"0xa2,0x01,0x03,0x52,"0341","凸轮轴信号不可靠"0xa2,0x01,0x03,0x61,"0350","没有曲轴信号"0xa2,0x01,0x03,0x62,"0351","曲轴信号不可信"0xa2,0x01,0x03,0x71,"0360","曲轴与凸轮轴信号偏差超出门槛值"0xa2,0x01,0x03,0x81,"0370","发动机转速超限"0xa2,0x01,0x03,0x91,"0380","排气制动蝶阀对电源短路或者超温"0xa2,0x01,0x03,0xa2,"0391","排气制动蝶阀地短路"0xa2,0x01,0x03,0xb4,"03a2","排气制动蝶阀没有信号"0xa2,0x01,0x03,0xb8,"03a3","排气制动蝶阀超温"0xa2,0x01,0x03,0xc8,"03b3","油量扭矩转化不可信"0xa2,0x01,0x03,0xd1,"03c0","燃油温度传感器电压超出上限门槛值"0xa2,0x01,0x03,0xd2,"03c1","燃油温度传感器电压超出下限门槛值"0xa2,0x01,0x03,0xe1,"03d0","风扇执行器(PWM波)对电源短路"0xa2,0x01,0x03,0xe2,"03d1","风扇执行器(PWM波)对地短路"0xa2,0x01,0x03,0xe4,"03d2","风扇执行器(PWM波)没有信号"0xa2,0x01,0x03,0xe8,"03d3","风扇执行器(PWM波)超温"0xa2,0x01,0x03,0xf1,"03e0","风扇执行器(数字信号)对电源短路"0xa2,0x01,0x03,0xf2,"03e1","风扇执行器(数字信号)对地短路"0xa2,0x01,0x04,0x01,"03f0","冷却风扇速度高出上限门槛值"0xa2,0x01,0x04,0x02,"03f1","冷却风扇速度低于下限门槛值"0xa2,0x01,0x04,0x11,"0400","燃油滤清器压差传感器电压高出上限门槛值" 0xa2,0x01,0x04,0x22,"0411","燃油滤清器压差传感器电压低于下限门槛值" 0xa2,0x01,0x04,0x38,"0423","燃油滤清器压差传感器信号不可信"0xa2,0x01,0x04,0x41,"0430","燃油滤清器加热器对电源短路"0xa2,0x01,0x04,0x42,"0431","燃油滤清器加热器对地短路"0xa2,0x01,0x04,0x51,"0440","油中有水传感器电压超出上限门槛值" 0xa2,0x01,0x04,0x62,"0451","油中有水传感器电压低于下限门槛值" 0xa2,0x01,0x04,0x74,"0462","燃油滤清器堵塞"0xa2,0x01,0x04,0x81,"0470","油中有水传感器检测到油中有水"0xa2,0x01,0x04,0x91,"0480","CAN-EngGsFlRtHtr 通讯错误"0xa2,0x01,0x04,0x92,"0481","CAN-EngGsFlRtHtr 通讯错误"0xa2,0x01,0x04,0x94,"0482","CAN-EngGsFlRtHtr 通讯错误"0xa2,0x01,0x04,0x98,"0483","CAN-EngGsFlRtHtr 通讯错误"0xa2,0x01,0x04,0xa1,"0490","CAN -RxEngTmp2Sens 通讯错误"0xa2,0x01,0x04,0xa2,"0491","CAN -RxEngTmp2Sens 通讯错误"0xa2,0x01,0x04,0xa4,"0492","CAN -RxEngTmp2Sens 通讯错误"0xa2,0x01,0x04,0xa8,"0493","CAN -RxEngTmp2Sens 通讯错误"0xa2,0x01,0x04,0xb1,"04a0","CAN -TODashDspl 通讯错误"0xa2,0x01,0x04,0xc4,"04b2","CAN-TOEBC1 通讯错误" 0xa2,0x01,0x04,0xd1,"04c0","CAN-TOERC1DR 通讯错误" 0xa2,0x01,0x04,0xe4,"04d2","CAN -TOETC1 通讯错误"0xa2,0x01,0x04,0xf4,"04e2","CAN -TOEngGsFlowR 通讯错误"0xa2,0x01,0x05,0x01,"04f0","CAN -TOHRVD 通讯错误" 0xa2,0x01,0x05,0x11,"0500","CAN -TORxAMCON 通讯错误" 0xa2,0x01,0x05,0x24,"0512","CAN-TORxCCVS 通讯错误" 0xa2,0x01,0x05,0x34,"0522","CAN-TORxEngTemp2 通讯错误" 0xa2,0x01,0x05,0x44,"0532","CAN-TOTCO1 通讯错误" 0xa2,0x01,0x05,0x51,"0540","CAN-TOTF 通讯错误" 0xa2,0x01,0x05,0x61,"0550","CAN -OTSC1AE 通讯错误" 0xa2,0x01,0x05,0x64,"0552","CAN -OTSC1AE 通讯错误" 0xa2,0x01,0x05,0x71,"0560","CAN -TOTSC1AR 通讯错误"0xa2,0x01,0x05,0x74,"0562","CAN -TOTSC1AR 通讯错误" 0xa2,0x01,0x05,0x81,"0570","CAN-TOTSC1DE 通讯错误" 0xa2,0x01,0x05,0x84,"0572","CAN-TOTSC1DE 通讯错误" 0xa2,0x01,0x05,0x91,"0580","CAN -TOTSC1DR 通讯错误" 0xa2,0x01,0x05,0x94,"0582","CAN -TOTSC1DR 通讯错误" 0xa2,0x01,0x05,0xa1,"0590","CAN-TOTSC1PE 通讯错误" 0xa2,0x01,0x05,0xa2,"0591","CAN-TOTSC1PE 通讯错误" 0xa2,0x01,0x05,0xb1,"05a0","CAN-TOTSC1TE 通讯错误" 0xa2,0x01,0x05,0xb4,"05a2","CAN-TOTSC1TE 通讯错误" 0xa2,0x01,0x05,0xc1,"05b0","CAN -TOTSC1TR 通讯错误" 0xa2,0x01,0x05,0xc4,"05b2","CAN -TOTSC1TR 通讯错误" 0xa2,0x01,0x05,0xd1,"05c0","CAN-TOTSC1VE 通讯错误" 0xa2,0x01,0x05,0xd4,"05c2","CAN-TOTSC1VE 通讯错误" 0xa2,0x01,0x05,0xe1,"05d0","CAN-TOTSC1VR 通讯错误" 0xa2,0x01,0x05,0xe4,"05d2","CAN-TOTSC1VR 通讯错误" 0xa2,0x01,0x05,0xf1,"05e0","CAN -TOTimeDate 通讯错误"0xa2,0x01,0x06,0x04,"05f2","CAN -TOWSI 通讯错误" 0xa2,0x01,0x06,0x14,"0602","CAN -TxTO通讯错误" 0xa2,0x01,0x06,0x21,"0610","档位提升间隙时间过长"0xa2,0x01,0x06,0x31,"0620","指示灯1电源短路"0xa2,0x01,0x06,0x32,"0621","指示灯1地短路"0xa2,0x01,0x06,0x34,"0622","指示灯1没有信号"0xa2,0x01,0x06,0x38,"0623","指示灯1超温"0xa2,0x01,0x06,0x41,"0630","指示灯2电源短路"0xa2,0x01,0x06,0x42,"0631","指示灯2地短路"0xa2,0x01,0x06,0x44,"0632","指示灯2没有信号"0xa2,0x01,0x06,0x48,"0633","指示灯2超温"0xa2,0x01,0x06,0x51,"0640","指示灯3电源短路"0xa2,0x01,0x06,0x52,"0641","指示灯3地短路"0xa2,0x01,0x06,0x54,"0642","指示灯3没有信号"0xa2,0x01,0x06,0x58,"0643","指示灯3超温"0xa2,0x01,0x06,0x61,"0650","CJ940通讯受干扰"0xa2,0x01,0x06,0x71,"0660","EEPROM报警"0xa2,0x01,0x06,0x72,"0661","EEPROM读错误"0xa2,0x01,0x06,0x74,"0662","EEPROM写错误"0xa2,0x01,0x06,0x78,"0663","EEPROM使用替代值"0xa2,0x01,0x06,0x88,"0673","系统修复故障"0xa2,0x01,0x06,0x98,"0683","系统修复故障"0xa2,0x01,0x06,0xa8,"0693","系统修复故障"0xa2,0x01,0x06,0xb1,"06a0","CJ940电压过高"0xa2,0x01,0x06,0xc2,"06b1","CJ940电压过低"0xa2,0x01,0x06,0xd1,"06c0","空气湿度传感器电压超出上限门槛值"0xa2,0x01,0x06,0xd2,"06c1","空气湿度传感器电压低于下限门槛值"0xa2,0x01,0x06,0xe1,"06d0","进气温度传感器电压超出上限门槛值"0xa2,0x01,0x06,0xe2,"06d1","进气温度传感器电压低于下限门槛值"0xa2,0x01,0x06,0xe4,"06d2","来自CAN进气温度传感器电压信号不可信" 0xa2,0x01,0x06,0xf1,"06e0","理想喷油次数受电流限制"0xa2,0x01,0x06,0xf2,"06e1","理想喷油次数受油量限制"0xa2,0x01,0x06,0xf4,"06e2","理想喷油次数受软件限制"0xa2,0x01,0x07,0x01,"06f0","1、2、3缸中某喷油器高端与电源或地短路" 0xa2,0x01,0x07,0x02,"06f1","1、2、3缸中某喷油器低端与地短路"0xa2,0x01,0x07,0x04,"06f2","看实际应用情况"0xa2,0x01,0x07,0x08,"06f3","没有标定的错误"0xa2,0x01,0x07,0x11,"0700","看实际应用情况"0xa2,0x01,0x07,0x12,"0701","看实际应用情况"0xa2,0x01,0x07,0x14,"0702","1、2、3缸中某喷油器断路"0xa2,0x01,0x07,0x18,"0703","看实际应用情况"0xa2,0x01,0x07,0x21,"0710","4、5、6缸中某喷油器高端与电源或地短路" 0xa2,0x01,0x07,0x22,"0711","4、5、6缸中某喷油器低端与地短路"0xa2,0x01,0x07,0x24,"0712","看实际应用情况"0xa2,0x01,0x07,0x28,"0713","没有标定的错误"0xa2,0x01,0x07,0x31,"0720","看实际应用情况"0xa2,0x01,0x07,0x32,"0721","看实际应用情况"0xa2,0x01,0x07,0x34,"0722","4、5、6缸中某喷油器断路"0xa2,0x01,0x07,0x38,"0723","看实际应用情况"0xa2,0x01,0x07,0x41,"0730","CY33X内部重新起动/时钟丢失/电压太高" 0xa2,0x01,0x07,0x42,"0731","CY33X没有被锁定/初始化错误"0xa2,0x01,0x07,0x44,"0732","CY33X工作在测试模式下"0xa2,0x01,0x07,0x48,"0733","CY33X SPI通讯错误"0xa2,0x01,0x07,0x51,"0740","CY33X内部奇偶错误"0xa2,0x01,0x07,0x52,"0741","CY33X程序错误"0xa2,0x01,0x07,0x54,"0742","CY33X check of inv. YSEL"0xa2,0x01,0x07,0x58,"0743","某缸的CY33X不工作"0xa2,0x01,0x07,0x61,"0750","喷油器1低端与电源短路"0xa2,0x01,0x07,0x62,"0751","看实际应用情况"0xa2,0x01,0x07,0x64,"0752","喷油器1高端与低端短路"0xa2,0x01,0x07,0x68,"0753","没有标定的错误"0xa2,0x01,0x07,0x71,"0760","看实际应用情况"0xa2,0x01,0x07,0x72,"0761","看实际应用情况"0xa2,0x01,0x07,0x74,"0762","喷油器1开路"0xa2,0x01,0x07,0x78,"0763","看实际应用情况"0xa2,0x01,0x07,0x81,"0770","喷油器2低端与电源短路" 0xa2,0x01,0x07,0x82,"0771","看实际应用情况"0xa2,0x01,0x07,0x84,"0772","喷油器2高端与低端短路" 0xa2,0x01,0x07,0x88,"0773","没有标定的错误"0xa2,0x01,0x07,0x91,"0780","看实际应用情况"0xa2,0x01,0x07,0x92,"0781","看实际应用情况"0xa2,0x01,0x07,0x94,"0782","喷油器2开路"0xa2,0x01,0x07,0x98,"0783","看实际应用情况"0xa2,0x01,0x07,0xa1,"0790","喷油器3低端与电源短路" 0xa2,0x01,0x07,0xa2,"0791","看实际应用情况"0xa2,0x01,0x07,0xa4,"0792","喷油器3高端与低端短路" 0xa2,0x01,0x07,0xa8,"0793","没有标定的错误"0xa2,0x01,0x07,0xb1,"07a0","看实际应用情况"0xa2,0x01,0x07,0xb2,"07a1","看实际应用情况"0xa2,0x01,0x07,0xb4,"07a2","喷油器3开路"0xa2,0x01,0x07,0xb8,"07a3","看实际应用情况"0xa2,0x01,0x07,0xc1,"07b0","喷油器4低端与电源短路" 0xa2,0x01,0x07,0xc2,"07b1","看实际应用情况"0xa2,0x01,0x07,0xc4,"07b2","喷油器4高端与低端短路" 0xa2,0x01,0x07,0xc8,"07b3","没有标定的错误"0xa2,0x01,0x07,0xd1,"07c0","看实际应用情况"0xa2,0x01,0x07,0xd2,"07c1","看实际应用情况"0xa2,0x01,0x07,0xd4,"07c2","喷油器4开路"0xa2,0x01,0x07,0xd8,"07c3","看实际应用情况"0xa2,0x01,0x07,0xe1,"07d0","喷油器5低端与电源短路"0xa2,0x01,0x07,0xe2,"07d1","看实际应用情况"0xa2,0x01,0x07,0xe4,"07d2","喷油器5高端与低端短路"0xa2,0x01,0x07,0xe8,"07d3","没有标定的错误"0xa2,0x01,0x07,0xf1,"07e0","看实际应用情况"0xa2,0x01,0x07,0xf2,"07e1","看实际应用情况"0xa2,0x01,0x07,0xf4,"07e2","喷油器5开路"0xa2,0x01,0x07,0xf8,"07e3","看实际应用情况"0xa2,0x01,0x08,0x01,"07f0","喷油器6低端与电源短路"0xa2,0x01,0x08,0x02,"07f1","看实际应用情况"0xa2,0x01,0x08,0x04,"07f2","喷油器6高端与低端短路"0xa2,0x01,0x08,0x08,"07f3","没有标定的错误"0xa2,0x01,0x08,0x11,"0800","看实际应用情况"0xa2,0x01,0x08,0x12,"0801","看实际应用情况"0xa2,0x01,0x08,0x14,"0802","喷油器6开路"0xa2,0x01,0x08,0x18,"0803","看实际应用情况"0xa2,0x01,0x08,0x21,"0810","正常工作的气缸数小于系统运转所需的最小缸数" 0xa2,0x01,0x08,0x22,"0811","未用"0xa2,0x01,0x08,0x24,"0812","未用"0xa2,0x01,0x08,0x28,"0813","未用"0xa2,0x01,0x08,0x38,"0823","巡航信号不可靠"0xa2,0x01,0x08,0x41,"0830","故障灯与电源短路"0xa2,0x01,0x08,0x42,"0831","故障灯与地短路"0xa2,0x01,0x08,0x44,"0832","故障灯没有信号"0xa2,0x01,0x08,0x48,"0833","故障灯超温"0xa2,0x01,0x08,0x51,"0840","主继电器2对电源短路"0xa2,0x01,0x08,0x52,"0841","主继电器2对地短路"0xa2,0x01,0x08,0x61,"0850","巡航开关对电源短路"0xa2,0x01,0x08,0x62,"0851","巡航开关对地短路"0xa2,0x01,0x08,0x68,"0853","巡航开关信号不可信"0xa2,0x01,0x08,0x71,"0860","主继电器1电源短路"0xa2,0x01,0x08,0x82,"0871","主继电器1地短路"0xa2,0x01,0x08,0x98,"0883","系统通讯故障"0xa2,0x01,0x08,0xa1,"0890","CAN通讯错误"0xa2,0x01,0x08,0xb1,"08a0","CAN通讯错误"0xa2,0x01,0x08,0xc1,"08b0","CAN通讯错误"0xa2,0x01,0x08,0xd1,"08c0","机油液位传感器电压电压超出上限"0xa2,0x01,0x08,0xd2,"08c1","机油液位传感器电压电压低于下限"0xa2,0x01,0x08,0xd4,"08c2","来自CAN的机油液位传感器信号不可靠" 0xa2,0x01,0x08,0xd8,"08c3","机油液位传感器信号不可靠"0xa2,0x01,0x08,0xe1,"08d0","机油压力传感器电压电压超出上限"0xa2,0x01,0x08,0xe2,"08d1","机油压力传感器电压电压低于下限"0xa2,0x01,0x08,0xe4,"08d2","机油压力传感器信号不可靠"0xa2,0x01,0x08,0xe8,"08d3","机油压力过高或机油温度信号不可靠"0xa2,0x01,0x08,0xf8,"08e3","机油压力过低"0xa2,0x01,0x09,0x01,"08f0","机油温度传感器电压超出上限门槛值"0xa2,0x01,0x09,0x02,"08f1","机油温度传感器电压低于下限门槛值"0xa2,0x01,0x09,0x04,"08f2","来自CAN的机油温度传感器信号不可信" 0xa2,0x01,0x09,0x08,"08f3","机油温度与冷却水温度信号"0xa2,0x01,0x09,0x18,"0903","机油温度与冷却水温度信号"0xa2,0x01,0x09,0x21,"0910","喷油器加电时间超出超速监视器设定值"0xa2,0x01,0x09,0x31,"0920","发动机转速不可信"0xa2,0x01,0x09,0x41,"0930","压力调节正偏差超出上限"0xa2,0x01,0x09,0x52,"0941","压力调节负偏差低于下限"0xa2,0x01,0x09,0x61,"0950","电动燃油泵对电源短路"0xa2,0x01,0x09,0x62,"0951","电动燃油泵对地短路"0xa2,0x01,0x09,0x64,"0952","电动燃油泵断路"0xa2,0x01,0x09,0x68,"0953","电动燃油泵超温"0xa2,0x01,0x09,0x78,"0963","加速测试错误"0xa2,0x01,0x09,0x82,"0971","看门狗开关错误"0xa2,0x01,0x09,0x84,"0972","冗余断缸测试电压超出上限"0xa2,0x01,0x09,0x88,"0973","冗余断缸测试电压低于下限"0xa2,0x01,0x09,0x91,"0980","传感器电源1电压超出上限门槛值"0xa2,0x01,0x09,0x92,"0981","传感器电源1电压低于下限门槛值"0xa2,0x01,0x09,0xa1,"0990","传感器电源2电压超出上限门槛值"0xa2,0x01,0x09,0xa2,"0991","传感器电源2电压低于下限门槛值"0xa2,0x01,0x09,0xb1,"09a0","传感器电源3电压超出上限门槛值"0xa2,0x01,0x09,0xb2,"09a1","传感器电源3电压低于下限门槛值"0xa2,0x01,0x09,0xc1,"09b0","断缸测试故障"0xa2,0x01,0x09,0xd1,"09c0","系统灯电源短路"0xa2,0x01,0x09,0xd2,"09c1","系统灯地短路"0xa2,0x01,0x09,0xd4,"09c2","没有系统灯信号"0xa2,0x01,0x09,0xd8,"09c3","系统灯超温"0xa2,0x01,0x09,0xe4,"09d2","T15信号错误"0xa2,0x01,0x09,0xf1,"09e0","T50接通时间超限"0xa2,0x01,0x0a,0x08,"09f3","时间处理器与系统计时器间的时间偏差超出门槛值" 0xa2,0x01,0x0a,0x11,"0a00","空气节流阀对电源短路"0xa2,0x01,0x0a,0x22,"0a11","空气节流阀对地短路"0xa2,0x01,0x0a,0x34,"0a22","空气节流阀没有信号"0xa2,0x01,0x0a,0x38,"0a23","空气节流阀超温"0xa2,0x01,0x0a,0x41,"0a30","车速1高于最大门槛值"0xa2,0x01,0x0a,0x42,"0a31","VSS或SPS传感器信号失效"0xa2,0x01,0x0a,0x44,"0a32","车速1的HW信号不可信"0xa2,0x01,0x0a,0x48,"0a33","车速1与喷油量及发动机转速不可信" 0xa2,0x01,0x0a,0x51,"0a40","车速2传感器电压高出上限门槛值" 0xa2,0x01,0x0a,0x52,"0a41","车速2传感器电压低于下限门槛值" 0xa2,0x01,0x0a,0x54,"0a42","来自CAN的车速信号无效"0xa2,0x01,0x0a,0x58,"0a43","车速2传感器电压信号不可信"0xa2,0x01,0x0a,0x61,"0a50","车速3信号脉宽超过上限门槛值"0xa2,0x01,0x0a,0x62,"0a51","车速3信号脉宽低于下限门槛值"0xa2,0x01,0x0a,0x64,"0a52","车速信号平均周期小于门槛值"0xa2,0x01,0x0a,0x74,"0a62","CAN通讯错误"0xa2,0x01,0x0a,0x78,"0a63","CAN通讯错误"0xa2,0x01,0x0a,0x88,"0a73","SPI通讯错误"0xa2,0x01,0x0a,0x91,"0a80","故障指示灯电源短路"0xa2,0x01,0x0a,0x92,"0a81","故障指示灯对地短路"0xa2,0x01,0x0a,0x94,"0a82","没有故障指示灯信号"0xa2,0x01,0x0a,0x98,"0a83","故障指示灯超温"0xa2,0x01,0x0a,0xa1,"0a90","空调压缩机对电源短路"0xa2,0x01,0x0a,0xa2,"0a91","空调压缩机对地短路"0xa2,0x01,0x0a,0xa4,"0a92","空调压缩机没有信号"0xa2,0x01,0x0a,0xa8,"0a93","空调压缩机超温"0xa2,0x01,0x0a,0xb1,"0aa0","BPA的AD转换信号超出上限"0xa2,0x01,0x0a,0xb2,"0aa1","BPA的AD转换信号低于下限"0xa2,0x01,0x0a,0xb4,"0aa2","BPA信号错误"0xa2,0x01,0x0a,0xc1,"0ab0","高压测试错误"0xa2,0x01,0x0a,0xd4,"0ac2","燃油计量器开路"0xa2,0x01,0x0a,0xd8,"0ac3","燃油计量器超温"0xa2,0x01,0x0a,0xe1,"0ad0","燃油计量器电源短路"0xa2,0x01,0x0a,0xf2,"0ae1","燃油计量器对地短路"0xa2,0x01,0x0b,0x01,"0af0","燃油计量器电压超过上限"0xa2,0x01,0x0b,0x02,"0af1","燃油计量器电压低于下限"0xa2,0x01,0x0b,0x11,"0b00","共轨泻压阀打开"0xa2,0x01,0x0b,0x12,"0b01","轨压要求时间超限"0xa2,0x01,0x0b,0x14,"0b02","压力波动时共轨泻压阀没有打开"0xa2,0x01,0x0b,0x21,"0b10","共轨泻压阀打开次数超出技术要求的最大次数"0xa2,0x01,0x0b,0x31,"0b20","轨压传感器电压超出上限门槛值"0xa2,0x01,0x0b,0x32,"0b21","轨压传感器电压低于下限门槛值"0xa2,0x01,0x0b,0x41,"0b30","轨压传感器电压超出最大偏差"0xa2,0x01,0x0b,0x42,"0b31","轨压传感器电压低于最小偏差"0xa2,0x01,0x0b,0x51,"0b40","轨压偏差超出上限门槛值"0xa2,0x01,0x0b,0x61,"0b50","轨压偏差超出上限门槛值并且喷油量超限"0xa2,0x01,0x0b,0x71,"0b60","轨压偏差低于下限门槛值并且喷油量低于门槛值"0xa2,0x01,0x0b,0x81,"0b70","轨压峰值低于下限门槛值"0xa2,0x01,0x0b,0x91,"0b80","轨压峰值超出上限门槛值"0xa2,0x01,0x0b,0xa1,"0b90","轨压下降过快"0xa2,0x01,0x0b,0xb1,"0ba0","超速模式下的油量剂量单元设定不可信"0xa2,0x01,0x0b,0xc1,"0bb0","燃油计量器中的油量超过门槛值"0xa2,0x01,0x0b,0xd1,"0bc0","轨压偏差超出门槛值并且燃油计量器中的油量超过门槛值"0xa2,0x01,0x0b,0xe1,"0bd0","12V传感器电源电压超过上限门槛值"0xa2,0x01,0x0b,0xe2,"0bd1","12V传感器电源低于下限门槛值"0xa2,0x01,0x0b,0xf1,"0be0","起动电机高端电源短路"0xa2,0x01,0x0b,0xf2,"0be1","起动电机高端对地短路"0xa2,0x01,0x0c,0x01,"0bf0","起动电机低端电源短路"0xa2,0x01,0x0c,0x02,"0bf1","起动电机低端对地短路"0xa2,0x01,0x0c,0x04,"0bf2","起动电机开路"0xa2,0x01,0x0c,0x11,"0c00","水温传感器工作正常但水温超出门槛值"0xa2,0x01,0x0c,0x21,"0c10","空转时，识别油量计量单元的变量修正错误"0xa2,0x01,0x0c,0x31,"0c20","制动开关错误的识别错误"0xa2,0x01,0x0c,0x41,"0c30","制动踏板踩下前，巡航控制抑制错误"0xa2,0x01,0x0c,0x51,"0c40","巡航控制要求的识别错误，使得故障灯常亮"0xa2,0x01,0x0c,0x61,"0c50","远程油门踏板1输出电压值超出上限" 0xa2,0x01,0x0c,0x62,"0c51","远程油门踏板1输出电压值低于下限" 0xa2,0x01,0x0c,0x64,"0c52","远程油门踏板1与远程油门踏板2的2倍的信号关系不可信" 0xa2,0x01,0x0c,0x71,"0c60","远程油门踏板2输出电压值超出上限" 0xa2,0x01,0x0c,0x72,"0c61","远程油门踏板2输出电压值低于下限" 0xa2,0x01,0x0c,0x74,"0c62","远程油门踏板2与远程油门踏板1的1/2的信号关系不可信"。