KSS(台湾凯士士) 尼龙扎线带 2012

GORE® TENARA®Sewing ThreadPROCESSING GUIDELINESFor seams thatoutlast the fabric.Successful sewing starts here GORE® TENARA® Sewing Thread is guaranteed to last for the life of the fabric in which it is sewn, making it the ideal sewing thread for outdoor and marine applications.GORE® TENARA® Sewing Thread can be sewn at 2,600 stitches per minuteor more. Because GORE® TENARA® Sewing Thread is made from expanded polytetrafluoro e thylene (ePTFE), the sewing process is slightly different from that used with typical polyester thread.Selecting and Balancing Your StitchYou can use GORE® TENARA® Sewing Thread with either a lockstitch or chainstitch type of sewing stitch. For either stitch, you should ensure the stitch is balanced to maximize seam strength and seam elasticity.Tension settings are crucial for balanced stitching. To set your lockstitch tension for GORE® TENARA® Sewing Thread:1. The starting bobbin tension setting should allow the bobbin to mimic a child’s yo-yo. The bobbin should slowly fall to the floor when suspended by the sewing thread.2. The bobbin thread tension should be adjusted as low as possible for a flat or running stitch on the bobbin thread. (See Figure 3).3. Gradually increase the tension on your top thread to obtain a balanced stitch and a tight seam.Note: To determine the stitch balance between the top and bottom threadsof a lockstitch, cut out a 10 cm length of your seam and pull out the top and bottom threads. Measure the length of both threads. If they are the same length, the stitch balance is adjusted properly.In a balanced lockstitch (stitch type 301), the topand bottom threads should meet in the middle of thefabric, forming distinct stitches on the top side andunderside o f the fabric as shown in Figures 1 and 2.If the top thread tension is too high or the bobbinthread tension too low, flat or running stitchesappear on the top of the fabric as shown in Figure 3.If the top thread tension is too low or the bobbinthread tension too high, flat or running stitchesappear on the underside of the fabric as shownin figure 4. The loose thread loops in Figure 4 arecommon when first using our heavier threads.A balanced chainstitch (stitch type 401) top threadappears similar to a balanced lockstitch as shown inFigure 5.The chainstitch top thread should be pulledcompletely to the underside o f the fabric, with thebottom thread appearing as shown in Figures 6 and 7.A poorly tensioned loose chainstitch bottom thread appears as in Figure 8.Figure 8Figure 3Figure 5Figure 7Figure 6Figure 2Figure 1Figure 4TroubleshootingWhen first using GORE® TENARA® Sewing Thread, you might find it helpful to use the following table as a guide to ensure the best performance of the thread. Once you are familiar with the characteristics of GORE® TENARA® Sewing Thread, your seams will last for the lifetime of the fabric.Possible Cause ActionExcess speed Reduce speedExcess thread tension Balance seam tension as described in“Selecting and Balancing Your Stitch.”Improper thread path Verify the thread path with your machinemanufacturer; use all recommended threadguides.Needle burr – bent or deflected needle strikes feed dog or throat plate Check the needle for burrs, and replace the needle if necessary.Burr on thread guide Use a magnifying glass to check all threadguides, and repair or replace any guides asneeded.Thread kinks Place spool socks over each spool of thread,extend spool sock up to first thread guide,or use thread brake on each spool.Broken thread take-up spring Replace.Bobbin and mechanical opener/bobbin case lifter not correctly adjusted Consult machine manufacturer or service technician.Type of Uneven Stitch ActionFlat or running top-stitch Decrease the tension of the top thread. Flat or running bottom-stitch Increase the tension of the top thread.Loops on the underside of the fabric (more common with heavy threads)Increase the tension of the top thread to approximately twice the tension used for TR/KTR thread, and balance the stitch as described in “Selecting and Balancing Your Stitch.”Possible Cause ActionImproper thread path Verify the thread path with your machinemanufacturer; use all recommended threadguides.Misaligned needle(Needle eye or cove should face the bobbin hook.)Rotate the needle clockwise until its eye faces the bobbin hook or is slightly rotated towards the hook as the hook approaches needle.Bent or deflected needle (Heavy fabrics can bend needle.)Replace the needle; if needles bend frequently, use a larger needle, or request stronger needles from your manufacturer.Incorrect needle size and/or needle construction(The needle may be too large, preventing the thread from consistently forming a loop. Special needles are available to reduce skipped stitches.)Use recommended needle size in the table, or try one size smaller. Contact needle supplier for skipped stitch reducing needles.Excess thread through the needle When pausing the machine, maintainpressure on the material with the presserfoot.Thread kinks Place spool socks over each spool of thread,or use thread brake on each spool.Worn bobbin hook(The hook should be pointed and sharp.)Replace the bobbin hook.Incorrect machine timing(The bobbin hook and needle must meet as per manufacturer specifications.)Use a timing gauge (available from your machine supplier) to adjust the machine timing per the manufacturer’s instructions.Incorrect bobbin hook placement: incorrect distance from needle Reposition the hook per the manufacturer’s instructions.Worn machine components(Needle bar, bearings, hook races, thread take-up spring, etc.)Replace components as needed. Reduce future wear by cleaning and lubricating per manufacturer’s recommendations.Chainstitching: incorrect looper position Reposition the looper closer to the needleper manufacturer’s instructions. If problemcontinues, consider replacing the looper. Chainstitching: Dull looper Replace looper, and ensure proper clearancefrom needle.Maintaining QualityMost importantly, please follow your sewing machine manufacturer’s maintenance schedule. Sewing machines are precision equipment that operates at high speeds. Cleaning and lubricating must be regularly scheduled to ensure continuous,trouble-free service. Oftentimes, problems with thread breaks and skipped stitches are due directly to misaligned and/or worn machine components. Many times these components wear out prematurely if they are not sufficiently cleaned and lubricated.You can ensure the best performance from GORE ® TENARA ® Sewing Thread by periodically checking the following parts and settings of the sewing machine:Part or Setting Visual Check ProblemSpool and thread stand alignment Spool center should be aligned with first thread guide and spool should beuprightMisalignment causes tension peaks and uneven stitches.Spool and threadstand distance Spool top should be within 6”–12”(15–30 cm) below of first thread guide Spool too close, spool will not unwind properly. Too far, thread “balloon” can catch on thread stand or other thread(double needle machines).Possible CauseAction Bobbin continues to rotate after themachine stops Use lightweight (aluminum) bobbins, anti-overrun washers, or “star washers” availablefrom your sewing machine manufacturer.When sewing double needle lockstitch applications, use an R needle pointshape on both left and right sides. If you experience skipped stitches or thread separation on the left needle, try using a CR type needle.Part or Setting Visual Check ProblemNeedle Point Point is sharp, and needleis straight.Dull or bent needles can cause skipped stitches and broken thread.Needle Condition Needle is free of burrs.Needle burrs typically occur when aneedle is deflected and strikes part ofthe machine. These burrs can causethread breakage.Needle Alignment Needle eye is alignedproperly with the hook.Misaligned needles may cause skipped stitches or thread breaks.Thread Tension Settings The thread tension onbobbin and top are assufficient to createbalanced stitches andtight seams.Tensions that are set too high can causethread to break or seams that are tootight. Tensions that are too low cancause loose and uneven stitches.Thread Guides Condition Guides should be cleanand free of burrs.Burrs and dirt on the thread guides cancatch the thread and cause unbalancedstitches or the thread to break.Hook Points Points are sharp andstraight.Hooks wear naturally during use and can cause skipped stitches or thread breaks when dull.Condition of Machine Components (Needle bar bearings, hook race, etc.)Machine components areclean and well lubricated.Worn machine components can causebroken thread, uneven seams, andskipped stitches.Bobbin Hook Position and Timing The hook is positionedclose to the needle,without touching theneedle.The bobbin hook can cause skippedstitches if too far from the needle.W. L. Gore & Associates, Inc. 100 Airport Road, PO Box 1010, Elkton, MD 21921, USA US Toll-Free 800.276.8451 T +1.410.506.8400 E *********************/tenara FOR INDUSTRIAL USE ONLY. Not for use in food, drug, cosmetic or medical device manufacturing, processing, or packaging operations. All technical information and advice given here is based on our previous experience. We give this information to the best of our knowledge, but assume no legal responsibility. The operating data given here has been determined under technically ideal conditions. Any deviations will depend on the conditions of the individual application and whether our sewing and processing instructions have been observed. In order to achieve the best possible results we would ask you to contact our product specialists with the full details of your application. They will be only too pleased to help you. Specifications are subject to change without notice.GORE, TENARA, Together, improving life and designs are trademarks of W. L. Gore & Associates. © 2011–2022 W. L. Gore & Associates, Inc.T E N -D S H -002-E N -J U L 22。

尼龙扎带之CHS长虹塑料集团知识详解尼龙扎带，作为在社会化大生产中显现的代替传统常规绑扎绳索的器材日益受到各行各业的广泛应用和普及推广。

起初，在上世纪7.80年代，我国大面积工业生产和社会日常使用涉及到的绑扎用途需求都采用诸如麻绳，棉线，草绳等等就地取材的生产产出辅料手工或机器制成，效率极低，应用领域极窄，劳动操作强度较大。

随后，由于沿海省份和地区加强外贸互动交流，尼龙扎带作为一种新奇的塑料制品渐然渗入国内，在电子，电器企业如雨后春笋般兴起的年月，真正的进入到线缆理线紧固的应用领域，用户感受到了尼龙扎带在其中的表现具有简便高效，美观实用，成本低廉，久固耐用等诸多便利和优势。

在得到实际的常规化应用后，继而在园林工艺，农业生产，建筑施工，广告施工等相关设计到固定器物，绑扎紧固的场所，尼龙扎带作为最具代表性的首选替代产品逐步的淘汰掉了传统绑扎绳索的应用。

随着生产分工的逐步细化和加深，尼龙扎带规格型号款式也由较为单一的自锁式扎带规格样式款型逐步拓展创新出各式各样扎带规格，千变万化的衍生款式出来，更加便利和有效的融入到绑扎紧固场所实际所需。

中国作为二十一世纪工业化发展排前的国度，在此领域短期内造成了相当大的需求空缺，这就迫切的需要尼龙扎带工业制造供给的配套到位。

乐清，作为最早引入这一前卫产业加工的地域，如今年月变迁虽过几十载，然而不断创新发展依然使得其依旧保持着尼龙扎带基地在乐清的不争的事实。

先进加工机器的不断升级细化，优质精密的模具加工工艺和先进的全自动机械手的引入，让尼龙扎带产品在性能和产能上有了更大的提升，让产品的成本价值有了更优势的下降。

谈到尼龙扎带，就不得不谈到长虹塑料集团，其前身由1987年的年产值不到10万，销售不过4省区的长虹塑料有限公司先前跃升到2012年的年产值3.5亿元，产品遍布全球80多个国家和地区的尼龙扎带集团化制造王国，2012年底已跻身成为亚洲最大规模产能的尼龙扎带塑料配线器材制造基地。

Stainless SPIKES NEEDLE STRIPSINSTRUCTIONMANUALINTRODUCTIONStainless SPIKES Needle Strips is the latest bird control product from Bird-X, recognized worldwide as the Bird Control "X-Perts" since 1964. We are the only company anywhere that sells a complete line of bird repelling products, including ultrasonic and sonic sound generators, visual scare devices, roosting inhibitors, netting and taste aversions. New product development is ongoing. Our sales consultants analyze problems and make recommendations based on each customer's specific needs.DESCRIPTION OF PRODUCT AND HOW IT WORKSNeedle strips are a simple, humane, maintenance-free, long-term solution to pest bird problems, and have been used on buildings and structures worldwide to eliminate roosting and nesting surfaces and landing strips. Birds avoid alighting on the spikes as humans avoid walking on a bed of nails – the spikes are not lethal, just extremely uncomfortable.Stainless SPIKES is a base mold of transparent polycarbonate with stainless steel projections protruding up and out (angled) to both sides. . There are three variations (see diagram & specs, next page):• Regular alternates wide stainless steel projections (4.5” spread) with narrow stainless steel projections (2.5” spread).• Slim Stainless SPIKES has only the narrower stainless steel projections (2.5” spread) in order to cover ledges less than 2" wide. • Extra-Wide alternates wide stainless steel projections (4.5” spread) with extra-wide (7.5” spread) AND narrower (2.5” spread)stainless steel projections.24 foot kit 50 foot kit100 foot kit REGULAR (#STS) #STS-24 #STS-50 #STS-100 SLIM (#SLS) #SLS-24 #SLS-50 #SLS-100EXTRA WIDE (#EWS) #EWS-24 #EWS-50 #EWS-100Designed and manufactured by:300 N. Oakley BlvdPhone 312-226-2473 Chicago, IL 60612 Fax 312-226-2480 USAWeb ********************SPECIFICATIONS – Stainless SPIKESDimensions: Height, Highest Point 4.3"Width, Base 1.7" Width, Widest Point (Regular) 4.5" (Slim) 2.5" (Extra Wide) 7.5”Diameter of hole in base 0.156”Net Weight: 16# per 100' Packaging: Kits of 24', 50' and 100'Material: Polycarbonate with UV Inhibitors, and ST302 Hard Surgical Grade Stainless; resistant to virtually all weather and harsh environmentsSPIKES Special Adhesive, part #SSA from Bird-X, Inc. is a high-performance weatherproof elastomeric adhesive. It exhibits exceptional bonding to a broad range of materials including metal, glass, plastic, composite, tile, cement, rubber, leather, wood and vinyl. Unlike many common adhesives:•Safe to ship by air•Not flammable material•No hazardous wasteSize: 10.5 oz. cartridge Application: standard caulking gunPRE-INSTALLATIONNo two bird infestation problems are exactly the same. Begin with research. Information related to the bird problem will have bearing on the actual installation and its success:Survey the birds. Type? Population? Patterns?Survey your property. What do birds find attractive about your area? Can it be changed?Remove all inducements. Eliminate nests, fledglings, droppings, dead birds, and the residual scent. Also remove food spillage, garbage, nesting material and other appealing items.Maintain a clean, changing environment. Continue to clean nests, debris and droppings.Install early. Install before "bird season" begins; it is easier to keep the birds away than to rout them out once they have already established a living pattern.Use products synergistically. Different kinds of devices (add a visual device or a sound repeller) produce a synergistic effect -- in combination the products yield much greater effectiveness than Stainless SPIKES alone. You may find this necessary if there are certain areas where it is undesirable or impractical to install spikes. This will maximize effectiveness throughout the entire property. Consider alternate locations. Apply to nearby locations where birds may go when they leave their current area.Familiarize yourself with the legal and public relations environment. Are there related environmental laws?Precaution: Although non-lethal, Stainless SPIKES’ actual projections are quite sharp. Wear protective gloves, and be careful duringinstallation and handling.INSTALLATIONStainless SPIKES can be mounted on any surface whether flat, curved orirregular, and on any material, whether masonry, metal, canvas, glass or wood. 24” units affix quickly with SPIKES Special Adhesive, screws, nails,wire ties, etc. Units may be “snapped” to fit lengths less than 24". Always firmly attachStainless SPIKES - never balance sections precariously or wedge them.COVERAGEStainless SPIKES is only effective where applied; nearby unprotected areas can encourage roosting. A working diagram while measuring will translate into a well-covered installation.Spacing: Measure the width of each area to be covered. For every 5" of width, use one row of Stainless SPIKES; for fractions thereof, use one row of SLIM Stainless SPIKES. For widths of 7” or more, use one row of EXTRA WIDE Stainless SPIKES. The projections from Stainless SPIKES should extend at least ½" past the exposed edge or edges of the area.Calculation of Linear Feet Needed: Measure the length of each area to be covered, allowing for curves or bends in the surface - flexible Stainless SPIKES will follow easily. Based on length (multiply length by 2, 3, etc. if necessary for wider widths) order an appropriate amount of Stainless SPIKES.AFFIXING Stainless SPIKES TO SURFACESStainless SPIKES is versatile, and easily attached to surfaces of every size, shape and material. Use any of the following methods, or devise your own.▪ SPIKES Special Adhesive: Bond only to dry, clean surfaces, when the temperature is between 32°F and 120°F. Apply a bead of adhesive to underside of base. Firmly press Stainless SPIKES onto surface so that it makes solid contact. Allow adhesive to dry and form a "rivet" through the holes in the base.) Part #SSA from Bird-X; one tube will affix approximately 20 feet of Stainless SPIKES.▪ Screws: Use #5 (1/8”) flat Phillips-head screws and a screwdriver with a shaft of at least 4". ▪ Nails: Use 1/8" nails and a nail set.▪ Wire Ties: Recommended for cabling, piping and thin railings. ▪ Clamps or Velcro : Use for temporary installations .GUIDE TO EFFECTIVE INSTALLATIONS (Reread PRE-INSTALLATION.) Thorough and proper planning, installation and follow-up maintenance are essential to bird control success.Preparation: Clean, disinfect and repair surface if damaged. Wear protection to avoid health hazards. Remove overhanging branches or foliage above the surface to be protected so birds cannot land to drop nesting material into Stainless SPIKES .Thorough Coverage: Install on all existing and potential roosting areas, and as necessary to surfaces directly above the currently infested areas, so that birds cannot drop debris into the Stainless SPIKES from these higher surfaces.Creative Coverage: Cover all exposed surfaces, inside corners and crevices. Because birds are stubborn, this may require vertical, sideways, diagonal or upside down mounting in addition to standard, right-side up mounting.APPLICATIONSCreativity and experimentation will govern, but the following illustrations suggest a few of the possibilities. ▪ Louvers, Eaves▪ Air conditioners — Use multiple strips to cover the entire depth. ▪ Ledges, Sills, Gutters and Pipes▪ Beams, Trusses, Support Structures▪ Signs, Letters, Church Crosses — Follow the shape on each letter or structure and cover every surface or crevice in which a bird canroost. Flexible Stainless SPIKES can make both concave and convex curves.Correctly spaced installations for various surface widths plus projections extending exposed edge.strips of Stainless SPIKES radiating outward anddownward from the highest point of the dome.▪ Statues, Columns, Cornices — Apply to base, andaround head, arms, curves, crevices and openings.▪ Roofs — Apply to roof perimeter, chimney, antennae,and the ridge on a gabled roof. Apply to the inside of achimney (projections facing inward) to keep animals out.▪ Cables — Apply to any cable thick enough to support abird (this is easy since base is 0.8" wide.)▪ Trees — Apply to tops of branches to stop birds. Applyin horizontal rings around a tree trunk, starting 4' fromthe ground, then higher at 5" intervals to stop climbinganimals (use a similar defense for Bird Baths and BirdFeeders.)TROUBLE SHOOTINGEvery bird infestation is a unique challenge, as numerousvariables are involved. Besides obvious differences (birdtype, infestation size, structure type and physical location…),environmental factors make it impossible to state installation“rules”. Here are suggestions to maximize effectiveness, butexperimentation is often required. Birds are creatures ofhabit, and they will try to reclaim their areas immediatelyafter installation. While they will be quickly discouraged,they will seek alternate areas. Therefore, make sureyou’ve…■ first read this manual and completely understand theinstallation procedure.■ installed sufficient linear feet, and sufficient rows onsurfaces wider than 5"■ treated non-yet-infested areas. If birds are routed from their original location only to move to a nearby untreated area, all efforts will have been in vain.■ cleaned and disinfected the infested area of nests, debris, etc. See GUIDE TO EFFECTIVE INSTALLATIONS. Repeat as necessary. ■ checked that no flaw exists in the application. If so, birds may find it and infest, and you may need to amend the application.SYNERGYYou may find certain areas where it is undesirable or impractical to install spikes. If this is the case, we suggest that you protect these untreated areas generally by using other products (visual repellers, sound repellers) in conjunction with the spikes. This will maximize effectiveness throughout the entire property. Call (312) 226-2473 or visit for information on companion products.WARRANTYBird-X, Inc. stainless spikes are manufactured to the highest quality standards of durable materials and are guaranteed to be free from defect for 10 years under normal use.Proof of purchase is required. Warranty covers cost of replacement SPIKES product only. Installation of material is not covered under warranty.Bird-X, Inc.’s warranty covers only those defects which arise as a result of normal use of the product, and do not apply to any product: (i) which has not been installed or maintained in accordance with any installation, operating or handling instructions provided by Bird-X, Inc., (ii) which has been altered or damaged by accident; (iii) which has been subjected to unusual physical stress, misuse, abuse, or negligence or (iv) which has been used other than in accordance with the product handling instructions.Your satisfaction is important to us. Since 1964, Bird-X, Inc. has helped countless corporate & institutional customers and homeowners solve their pest bird & animal problems – safely and humanely. We are proud of our products and reputation. Please contact Customer Service to answer any questions, for help in resolving any issues or problems, and prior to returning any item for any reason.*****************************.(+1)3122262473 Copyright 2014 by Bird-X, Inc. All rights reserved.。

Kuesters 2C02第十届中国国际纺织机械展览会HUBER+SUHNER集团公司下BERKOL.事业部提供各种硬度系列的皮辊满足不同需要.通过与世界各地的知名纺织厂和机器制造商的紧密合作,一直在不断地改善产品规格以满足最新的需求.皮圈BERKOL.皮圈适用于粗纱机和细纱机.保养机器全套机器设备满足纺纱厂皮辊车间的需求.KarlMayer2C07KarlMayer(卡尔?迈耶)公司将展示面向亚洲市场的系列产品.在花边生产方面将展出KarlMayer公司新一代花边机家族中最先进机型之一.这种已经在全球应用非常成功的创新生产技术采用一种全新的提花技术同时由于效率的进一步提高,这种新技术在加工产品品种方面具有更高的灵活性.3梳栉特里科经编机也经过了彻底改造它与展出的花边机在经编生产方面形成互补.在CITME2006上展出的型号工作宽度为186英寸针距为E28强调KarlMayer 公司的技术能够成功地满足特定市场需求.KarlMayer公司还将展出1台配备GV筒子架和CSB—PW1800型浆槽的ZMSP1800型直接整经机以展示该公司的经纱准备技术.这种最新一代经纱准备技术已经成功地打入全球市场现在轮到中国生产商来领略该技术的先进性.其技术特点包括OPC联网能力和分析软件,一种新开发的和受专利保护的夹纱器和具有快速反应能力的纱线传感器.另外KARLMAYERServicePlus服务包为用户提供可靠的技术支持以确保所有机械和设备不间断运转.KARLMAYERTeleservice系统是这个服务包的一部分将在展会上现场演示.总之,KarlMayer公司将通过展出这些设备来体现其在世界舞台上的地位和满足不同国家特殊需求的意识. Knotex2C21德国Knotex(诺泰克斯)公司将展示一系列新的或经过改进的产品.ASE/2quattro型结经机是Knotex公司最成功的一款结经机.该机可利用现有4种结经方法对各种天然和合成纤5召纺织导报ChinaTe×tileLeader.2006N0.10维纱进行高质量打结.它配备了具有传奇色彩的4合l装置和方便,安全的KnotexKnotControl.控制装置.RSD/2型结经机是一种新开发的结经机,适合于打单头结和双头结.采用一个操作杆来控制打结形式的转换. RSD/2~备采用各种结经方法,可互换的结经方法.Knotex KnotControl.控制装置作为选择性装置提供.Knotex公司还提供断纱检测器.这种新产品适用于Knotex公司的各种结经机.出现断头时或结经后发生漏结现象时探测器会使机器自动停机,以避免结经缺陷. KnotexOptimalSpeed是一种程序控制装置可调整效率与最高结经速度之间的关系.首台面世的结经机可通过扫描主要机器参数优化结经速度,结经速度可达600次/min. TS/2型结经机是专门为单丝结经而开发的,适合于加工纤度从l0dtex到直径为0.6mm的材料.该机已经广泛地用于全球造纸毡领域.Kuesters2C02在CITME2006上在齐塔乌新组建的KuestersTex. tileGmbH(寇司德纺织公司)和在克莱菲尔德的Andritz Kuesters(爱德华寇司德)公司的非织造部门连同寇司德上海子公司将在寇司德在北京——精诚合作"的口号下向中国市场展现寇司德公司德最新产品系列. Kuesters纺织公司对原有的着名均匀轧车的窄幅和宽幅机型都进行了升级使它们在压力调节方面具有了双倍的修正潜力.均匀辊包覆了新型蓝色的橡胶套它的表面可以适用于所有染色工艺.这种橡胶套还有着高耐化学腐蚀性!"即插即用"的设计大大简化了安装过程. AndritzKuesters公司这次带来了最新的轧光机特别是非织造布湿整理方面的技术.Kuesters公司拥有与非织造布工业不断发展的需求相配套的,经过验证的技术.例如轻薄涂层(KissRoll涂层辊筒),浸渍(均匀辊浸轧机),脱水(高效均匀辊轧水车)定量给料和工艺控制等方面的最新技术.公司同时还考虑了与着名助剂供应商的产品理第十届中国国际纺织机械展览会念相配合如碳氟化合物整理.寇司德上海公司也不甘落后在此次展览会上将隆重推出新开发的"灵巧型轧车222.65".它能灵活的组合在现有的各种纺织长车中,帮助提高原有工艺的效率,降低能耗和节约成本.在CITME期间,Kuesters将展示以下产品系列:机织和梭织织物的湿整理线(退浆,漂白,丝光,水洗,染色,脱水).也有地毯和毛圈织物的湿整理线(前处理染色,汽蒸水洗);配置有挠度补偿辊系统的纺织以及非织造布生产用轧光机;非织造布后整理技术;真空抽吸和定量给料系统,染料和化学品配给站,工艺自动化系统.Leopfe5B01作为着名的纺织质量控制设备专家,Leopfe(洛菲)公司将展出下列产品.在纺纱方面Y ARNMASTER.SPECTRA:该产品是面向络筒领域的成熟清纱和质量控制系统的延伸.Y ARNMASTER.ZENIT:最新一代的产品可满足最高生产要求包括:合成异纤的探测和清除(无论纱是何种颜色含何种异纤,即使是本色纱中白色和透明的丙纶也能探测到,并有效清除);可以探测到非常细小的异6D纺织导报ChinaTextileLeader.2006No.10纤;LabPack功能可提供表面指数SFI和纱疵指数IPI;经过长期在实际生产条件下的试验,证明该产品可靠性强. MILLMAsTER.简便型/标准型/提高型:该产品是所有Y arnMaster数据的中央和双向在线质量管理系统.它可实现对生产系统的完全监测和对质量和生产数据进行全面分析和评估.MILLMASTER.VISUAL:可使Y arnMaster在织物上检测到的质量实现在线可视化.在织造方面WEFTMASTER.:用于织造行业,包括:纬停装置,短纬探测器,纬纱制动器片梭制动器检结器,探纬针,热融织物剪刀,各种用途的断纱自停装置,等等.Mahlo2B10除了在自动化领域的诸多成果外,德国Mahlo(玛诺)公司将展出一台全新的OrthopacRVMC一12型整纬器.该机是在Mahlo公司多年制造整纬器和工艺控制系统的经验基础上开发的,采用模块式设计,可根据客户的具体需求灵活组合.OrthopacRVMC一12型整纬器采用灵敏度非常高的电子探测元件和智能化信号处理系统适用于加工各种织物.即使在加工最复杂的织物组织时这种整纬器也能进行有效探测和自动校正.另外,用于监测和控制温度,定形时间,织物含潮率,废气排放湿度和织物重量的各种传感器也可通过以太网与电子系统连接,并集成到电控箱中.包括纬斜情况在内的所有检测数值都可在作为人一机对话界面的TFT触摸式显示屏上显示.此外,Mahlo公司还将展出用于监测和控制定形时间,剩余含潮率,废弃排放和单位重量等参数的OPTICPAC VMC一12型工艺控制系统和在全幅织物上移动来检测织物单位重量,含潮率和厚度等参数的QualiscanQMS一12型质量控制系统.Monforts2C04Monforts(门富士)公司展出的新产品包括新的旗舰产品Montex6500型拉幅机,MatexTop-S轧车和用于免烫整理的湿交联工艺(MXL).Monforts公司将首次在中国展出1台与实物大小一样,。

XXXX公司自锁式聚酰胺（尼龙）扎带供货技术要求编制：审核：批准：1、概述本供货技术要求适用于XXXX公司集采招标采购范围中的自锁式聚酰胺（尼龙）扎带。

为了保证公司自锁式聚酰胺（尼龙）扎带的采购, 符合标准及各项目的技术要求，特出此文件。

2、产品设计、制造与验收标准规范扎带应符合下列标准，标准未注年代号，应为最新版本的标准。

QB/T 4494-2013 自锁式聚酰胺扎带3、使用、运输和储存条件3.1 仓储环境要求能防雨，防太阳直射，温度控制在 5-45 度之间（寒冷地区控制在-5-45度），相对湿度30%-95%，库房应保持干燥通风，以免产品水分流失或受潮而使其硬度，拉力发生变化而影响使用效果。

运输和贮存中应避免长期受压和其它机械损伤。

3.2 库存时间如超过半年需重新检验，确认产品拉力，韧性符合标准方可使用。

3.3 产品拆包后，如当天未使用完需密封包装，以免水分流失或受潮而使其变硬，拉力偏高，脆断，破裂等现象；同时避免高湿环境使扎带不断吸收水分造成拉力变低，出现拉长，拉断，松脱不良现象。

4、技术要求4.1 材料：4.1.1 扎带的材料应为尼龙66或少量的尼龙6（PA，自然色）材料，不得采用聚丙烯（PP）或类似材料。

4.1.2 扎带环保须符合欧盟 RoHS 环保指令要求。

使用范围：温度在-20℃~85℃环境下使用；长期暴露在室外场合或高温环境下应选用不同性能的扎带，如耐候或耐高温扎带，但需要根据环境情况定时更换。

（一般使用时效为3-5年）4.2 产品外观质量：4.2.1 扎带表面色泽应均匀、平整而有光泽，无暗泡、开裂及飞边，无杂色等缺陷。

4.2.2 扎带应柔软，无裂纹或断裂。

4.2.3 扎带的颜色为尼龙的自然微黄色或微白色。

4.2.4 扎带齿形正常、完整，无缺齿、少齿、断齿现象；卡扣完整无缺料现象。

4.3 结构尺寸：L——总长度；W——扎带宽度扎带的尺寸一般公差：长度公差±5mm，宽度公差±0.15mm，厚度公差±0.15mm。