FURUNO中文雷达操作说明
- 格式：pdf
- 大小：12.24 MB
- 文档页数：143
1 RADAR OPERATION 雷达操作
1.1 Turning on the Power
开启雷达
The [POWER] switch is located at the left corner of the control unit. Open the power switch cover and press the switch to turn on the radar system. To turn off the radar, press the switch again. The screen shows the bearing scale and digital timer approximately 30 seconds after power-on. The timer counts down three minutes of warm-up time. During this period the magnetron (transmitter tube) is warmed for transmission. When the timer has reached 0:00, the indication "ST-BY" appears at the screen center, meaning the radar is now ready to transmit pulses. 电源键位于控制面板的左上角。打开电源盖、按下打开电源。再次按下关闭电源。电源开启后30秒屏幕显示方位圈、电子计数器，计数器倒计时3分钟磁控管预热时间。但计数器时间归零，屏幕中央显示“待机”，表示雷达已准备发射。 In the stand-by condition, markers, rings, map, charts, etc. are not shown. Further, ARP is cancelled and the AIS display is erased. 在待机的情况下，标志、距标圈、海图登将不显示。ARPA功能取消，AIS显示取消。 In warm-up and stand-by condition, ON TIME and TX TIME counts in hours and tenths of hour appear at the screen center. 在预热和待机的情况下，使用时间和发射时间键显示在屏幕中间（*.*H） 1.2 Transmitter ON
打开发射器
After the power is turned on and the magnetron has warmed up, ST-BY appears at the screen center,
meaning the radar is ready to transmit radar pulses. You may transmit by pressing the [STBY/TX] key
on the full keyboard or roll the trackball to choose the TX STBY box at the bottom left corner of the
display and then push the left button (above the trackball). The label at the left-hand side of the
guidance box at the bottom right corner of the screen changes from TX to STBY 在电源打开、磁控管预热后，ST-BY显示在屏幕中间，表示已准备发射。按准备键或用鼠标选择屏幕左下角的发射准备框打开雷达 雷达显示
The radar is initially set to previously used range and pulse length. Other settings such as brilliance levels, VRMs,
EBLs and menu option selections are also set to previous settings.
雷达的设定（量程、脉冲长度、亮度、活动距标圈、电子方位线、菜单选项等）为上次关机时的设定
The [STBY/TX] key (orTX STBY box) toggles the radar between STBY and TRANSMIT status. The antenna stops
in stand-by and rotates in transmit. The magnetron ages with time resulting in a reduction of output power.
Therefore, it is highly recommended that the radar be set to stand-by when not used for an extended period of time. ST-BY键联系雷达待机和发射两种状态。待机状态下天线不转动、在发射状态下转动，磁控管的使用时间影响输出功
率的大小，因此前来建议在雷达长时间不使用的情况下键雷达设于待机状态。 Quick start
快速启动
Provided that the radar was once in use with the transmitter tube (magnetron) still warm, you can turn the radar into
TRANSMIT condition without three minutes of warm-up. If the [POWER] switch has been turned off by mistake or
the like and you wish to restart the radar promptly, turn on the [POWER] switch not later than 10 seconds after
power-off. 如果雷达仍在使用，磁控管仍然预热，可以无需等待3分钟。如果误关机，又马上要开机，请在10秒内马上打开电源。
1.3 Control Unit
控制单元
Two types of control units are available: Control Unit RCU-014 (full keyboard) and Control Unit RCU-105
(palm control).
本雷达提供两种控制单元，RCU-014型键盘式、RCU-105型手掌式
Control description
控键 Control控键 Description功能描述
Control Unit RCU-014 (full keyboard) RCU-014型键盘式
POWER电源 Turns the system on and off.开关电源
EBL and VRM rotary controls电子方位线、活动距标圈转盘 Adjust EBL and VRM, respectively. 调节电子方位线、活动距标圈
EBLON, EBL OFF电子方位线开关 Turns the EBLs on and off, respectively. 开关电子方位线
F1-F4功能键 Execute menu short cut assigned.快捷键
ALARM ACK警报确认 Silences audible alarm.关闭声响警报
STBY TX待机键 Toggles between stand-by and transmit.待机或发射
BRILL亮度 Adjusts display brilliance.调节显示亮度
A/C RAIN自动雨雪抑制 Suppresses rain clutter.抑制雨雪杂波
A/C SEA自动海浪抑制 Suppresses sea clutter.抑制海浪杂波
GAIN增益 Adjusts sensitivity of the radar receiver.调节雷达接收器灵敏度
HLOFF船首线关闭 Temporarily erases the heading line while pressed.临时消除船首线（按住） EBL OFFSET 电子方位线偏心显示 Enables, disables the EBL offset. In menu operation, switches polarity from North to South and East to West and vice versa.开启关闭电子方位线偏心显示，菜单操作时选择南或北、东或西 MODE显示模式 Chooses presentation mode。选择显示模式
OFF CENTER偏心显示 Shifts own ship position.调整本船位置
CU/TM RESET 真运动、航向向上显示复位 Moves own ship position in 75% radius in stern direction. • Resets the heading line
to 0° in course-up and true motion modes.
真运动、航向向上时，船首线复位至零、本船至船尾方向半径75%处， INDEX LINE索引线 Turns index lines on and off.开关索引线
VECTOR TIME矢量时间 Chooses vector time (length).调节矢量长度
VECTOR MODE矢量模式 Chooses vector mode, relative or true.选择真矢量或相对矢量
TARGET LIST物标列表 Displays ARP target list.显示ARPA物标列表
CANCEL TRAILS取消尾迹 Cancels all target trails. In menu operation it clears line of data. 取消物标尾迹，菜单操作中清除数据线
ENTER MARK插入标志 Enters marks; terminates keyboard input.插入标志；终止键盘输入
VRM ON, VRM OFF活动距标圈开关 Turns the VRMs on and off, respectively开启或关闭活动距标圈
MENU菜单 Opens and closes the MAIN menu; closes other menus.开关菜单
ACQ确认 • Acquires a target for ARP after choosing it with the trackball. • Changes a sleeping
