Ball valves_parts_DN150-1400_PN100

Metal Ball Valves—Flanged, Threaded, and Welding Ends金属球阀-法兰、螺纹、和焊接端1 Scope1 范围1.1 This standard specifies the requirements for metal ball valves suitable for petroleum, petrochemical, and industrial applications— corresponding to the nominal pipe sizes in ASME B36.10M—that have:这个标准规定了适用于石油、石化、工业应用的和公称直径阀门符合ASME B36.10M的阀门，范围如下：— flanged ends in sizes DN 15 through DN 600 (NPS 1/2 through NPS 24);--法兰端：DN15-DN600(NPS1/2-NPS24)— butt-welding ends in sizes DN 15 through DN 600 (NPS 1/2 through NPS 24);--对焊端：DN15-DN600(NPS1/2-NPS2);— socket-welding ends in sizes DN 8 through DN 50 (NPS 1/4 through NPS 2); and--套焊端：DN8-DN50(NPS1/4-NPS2);— threaded ends in sizes DN 8 through DN 50 (NPS 1/4 through NPS 2)--螺纹端：DN8-DN50(NPS1/4-NPS2)1.2 This standard applies to metal ball valves with pressure classes as follows:— flanged ends in Classes 150, 300, and 600;— butt-welding ends in Classes 150, 300, 600, and 800;— socket-welding ends in Classes 150, 300, 600, and 800;— threaded ends in Classes 150, 300, 600, and 800.1.3 This standard establishes requirements for bore sizes described as:1.3本标准对通径尺寸的要求描述如下：— full bore;--全通径— single reduced bore;--单缩径— double reduced bore.--全通径1.4 This standard applies to floating (seat-supported) ball (Figure C.1) and trunnion ball valve designs (Figure C.2). These figures are to be used only for the purpose of establishing standard nomenclature for valve components—other floating and trunnion designs also exist.1.4本标准适用浮动（阀座支撑）球阀（图C.1）和固定球阀（图C.2），这些图仅用于建立阀门部件术语的目的。

Product Manual- Operation and Maintenance Manual Product Name:API 6D Ball ValveJanuary 20121ScopeThis manual covers manually/motor/pneumatic operated seat supported /trunnion supported ball valve having tow/three pieces body with nominal sizes DN 15mm-1200mm (1/2”-48”) and class ranges PN1.6MPa-10MPa(ANS1 class 150-2500).Valve ends may be threaded, flanged, butt-welded or socket2 Applications2.1 Ball valves are used to open/close the flow in pipeline.2.2 The nature of applicable fluid depends on valve material:2.2.1 Carbon steel valve applies to non-corrosive fluid, such as water, vapor or oil etc. 2.3 Temperature range depend on sent material:PTFE ≤130℃RPTFE ≤160℃PPL ≤300℃NYLON ≤121℃3. standard：Basic design API 6D-2008Inspe crlon tesring BS EN 12266.1-2003End flange ASME B16.5-2009TEMP. & PRESSURE ASME B16.34-2009Face toface ASME B16.10-2009Main parts and materials ASME materials, see Table 1Figure 1:Trunnion Ball Valve4 Structure4.1 Ball Valve structure is shown in Fig. 1.4.2 List the major components and materials shown in Table 1:Table 1: Major Parts and Materials-29℃~38℃working pressure（bar）50℃working pressure（bar）100℃working pressure（bar）121℃working pressure（bar）6 OperationThe valve can be manually operated by using the handle for manually operated valves or motor-operated by the electric actuator for motor operated valves or pneumatic operated by pneumatic actuator for pneumatic operated valves. The valve open or closes by turning the ball. Clockwise turning to 90ºresults in valve open.6.1 The manually operated valve is opened when the handle and the position mark on stem end are parallel to pipeline. When that is perpendicular to the pipeline, the valve is closed.6.2 For motor/pneumatic operated valves, valve open/close is indicated by the positioner on the electric/pneumatic actuator.7 Storage, maintenance, installation and service7.1 The valve should be stored in dry room with good ventilation. Valve ends should be covered.7.2 For valve stored for a long period of time, regular checkup is required to ensure that the valves are in good conditions. Foreign particles should be removed and special care should be taken to keep the valve seat sealing surface clean and prevent any damage of sealing surface.7.3 Check the conformance of valve identification to the service requirements prior to installation.7.4 Check the cleanness of the valve cavity and sealing surface and sealing surface and wipe off any dirt with white cloth prior to installation.7.5 Before installation, the tightness of packing should be checked to ensure that sealing is secured without affecting the turning of stem.7.6 The valve shall be in full open position when conducting system or pip line pressure test after the valve installation.7.7 Ball valve shall be in full open or full close position while in service. partial opening for controlling the flow is not allowed.7.8 Manually operated valve should be operated by using the handle. Use of lowers or other tools is not allowed.7.9 Valve in service should be examined at prescribed intervals to see whether the wear of sealing surface or stem occurs and the gasket or packing fails. Repair or replacement shall be carried out timely if necessary.7.10 “Electric valve actuator instruction manual” and “Pneumatic valve actuator instruction manual” should be referred with regard to the storage, maintenance, installation and service for motor-operated valve and pneumatic-operated valve respectively.8 Possible troubles, causes and solutions see table9 GuaranteeGuarantee period is one year after service date no later than 18 months after delivery date. Valve failure due to material defectives, manufacturing problems, design unreasonable or any damage under normal operating conditions will be repaired or parts replaced free of charge by manufacturer within the guarantee period.。

Cat.no.:E-BFVCat.no.:E-PVCat.no.:E-CSV Cat.no.:E-PS Cat.no.:E-FSVCat.no.:E-PLVNo.999 Xiangjiang Road, Suzhou New District,P .R. China Post Code:215129Tel: 86-512-666-51365Fax: 86-512-666-51360E-Mail: neway@ C a t .n o .:E -P V -2005-U S12315 Parc Crest Drive Suite 190Stafford, T exas 77477Phone: 281-933-5775Fax: 281-933-5779JAG Flocomponents USA, Ltd.U.S. Sole Distributor:Manufacturer:Cat.no.:E-MVN the safety and protection ofe w a y r e c o g n i z e s t h eimportance of valve quality for personnel health and property. It is our quality commitment to focus our resources to provide our customers with first class products at a competitive price, that are designed, manufactured, inspected and tested in accordance with our customers, specifications and that comply with all international standards.With respect to the facts that the current industrial standards do not always take into consideration the likelihood and consequences of possible deterioration in service, related to specific service fluids or the external environment in which they operate. Our customers are requested to keep an open line of communication withNEWAY technical research center utilizes the most advanced computertechnology to improve the existing products and develop the new lines, this includes a highly educated and trained engineering team and a comprehensive internal computer network which links the entire operations of design, manufacturing and administration.NEWAY design philosophy is to develop a safety and cost-efficient valve, we introduced the latest AUTO CAD and I-DEAS software for all our new product design research which include the advanced finite element analysis to virtually verify the new design prior to production, this has resulted in dramatically reducing the new product design time and ensure a safety and cost efficient final product.NEWAY technical personnel are always ready to offer on line or on site technical training and support for all of its distributors, agents and end users.Fire safe is standard design of all NEWAY ball valve.Technical InnovationAPI 6D API 607API 6FA BS 5351BS 6755ANSI B16.34ANSI B16.10ANSI B16.5MSS SP-25MSS SP-55 NACE Std MR0175SHELL MESCAPI 598 Fire Safe Test CertificateTest FacilityTest ChartCNC LatheThe latest computer technology are also widely applied in NEWAY for valve manufacturing, this include a large number of numeric control machines (Machining center, CNC horizontal and vertical lathe, CNC drilling machine) and ERP management system which significantly improve our machining quality and process control. NEWAY also employes a number of conventional lathe with capacity up to machine 48ball valve.NEWAY manufacturing philosophy is to ensure stable quality and just in time delivery.4.2M Lathe CNC Lathe Automatic welding MachineMachining CenterCNC DrillingNEWAY developed an extensive and advanced inspection and test facilities to control the quality from rough castings or forgings to final products. These facilities enable us to do Radio graphic test, Ultra-sonic test, Dye-penetrate test, Magnetic test, Positive Material Identifier (PMI), Impact test, T ensile test, Hardness test, Fire safe test, Cryogenic test, Vacuum test, Low fugitive emission test and Hydro-static test.NEWAY Quality Assurance is dedicated to the pursuit of a zero defect valve, and this has resulted in the company having more quality qualifications and end user approval than most of our competitors. NEWAY is certified by ISO 9001 (certificate under DNV) and API 6D (registered no. 6D-0285) and our off-shore platform valves are type approved by ABS. Moreover, NEWAY is the first valve manufacturer in China to be certified to CE/PED (category IV, mode B+D, certificate under B.V.), All of NEWAY soft seated ball valves are fire safe tested and certified by Lloyd s Register.Part number identificationControlled Stem & Stuffing Box FinishFor the elimination of air pollution, it is essential to control the fugitive emissions leakage of various chemicals from valves in your chemical plant. NEWAY low emissions ball valves installed with our emissions defense packing have been designed and tested to m e e t t h e 100 P P M m a x i m u m e m i s s i o n l e v e l (acceptance test per Shell SPE 77/312). This is NEWAYstandard specification for all series BA, B and BB flanged floating ball valve.The stem surface finish is controlled between Weather proofbelleville-spring washerLow Emission packingFire Safe Seat SealingAdditionally, the fire safe metal seat can prevent the line pressure erosion on soft seat and minimize soft seat creep deformation. All NEWAY floating valves fire safe is designed and test certified in accordance with API 607.When static are generated and concentrated on the ball, the spring-loaded pins installed on ball, stem are provided to ensure electrical continuity throughout the valve.Anti-Static DeviceStem lower end is integral T shaped designed to be blow-out proof. It is internally inserted and functions as the backseat for assured stem sealing at all pressuresBlow-out Proof StemBefore FireBodyStemPacking ClosureBall StemPackingBallSeatBodyPackingStemAnti-Static DeviceClosureBodyBallGasketClosureWhen non-metal sealing material are decomposed or deteriorated by a plant fire, the upstream line pressure pull the ball into contact with the metal seat lip beneath the soft seat to shut off the line fluid to minimize the internal leakage.Design Feature:Live Loaded Gland FlangeLow Emission PackingLive loading is designed to provide gland load retention, compensating for expected in-service consolidation of the packing. A set of Belleville-Spring Washers are used on each gland stud to help exert a continuous compressive force on the gland follower flange and therefore reduce fugitive emissions from the stem packing. NEWAY standard Belleville-Spring Washers are protected by a weatherproof cap to keep them free from environmental contamination, resulting in a longstable life.The packing set is a combination of parallel and vertical layer sealing elements, which are made of expanding graphite in die-formed rings and have features of heat resistance, less stress relaxation and low creep. With this special structure, it allows for a low-friction on rotary & rising stem valves, therefore providing the stabilized seal performance for long cycle life.For medium and low temperature service, the standard V shape PTFE packing rings are installed for lowemission control.Floating Ball Valve Design FeatureLow Emission Control2963161861171514128137541110Series FE1 Ball ValveRegular port, uni-body, end entry designBlow-out Proof StemInternally inserted and functions as the backseat for assured stem sealing at all pressuresMetal-to-Metal Sealing When non-meatl sealing is deteriorated by fire,ball floats to shut off the line fruidEmission-free Graphite primary gasketIndex noPart123456789Index no PartBody Closure BallGland Flange Lever Seat Ring Stem Gland Gasket101112131415161718Grounding Washer Packing Set Stop Plate Thrust Washer Retainer Washer Bolt Rotaining SpringSeries FE1 Ball ValveSeries FE1 Ball ValveRegular port,uni-body,cast steel,end entry designClass 150LBWeight KgW mmH mmL mmD mmd mmSizeinDimensionsWW DLdHWDLddHGear Operator1 / 22 3101 / 23 / 411-1/222-1/23468101 / 23 / 49.512.71930385164761141441879.512.712.71925.43851647610215220325412.719108117127165178191203229267292330140152545964901021121211662082463035459120140140160265265265300400 300 * 400 *120140 1.72.72.985.008.7112.416.6624.38541011502.83.61638111071817962416135151412Series FB2 Ball Valveavailable in size from to 12 full port or witnessed and certified by Lloyd s Register.Double "D" Stem HeadProvides mounting of the lever handle alwaysin parallel to the flow passage Blow-out Proof Stem Internally inserted and functions as the backseat for assured stem sealing at all pressuresEmission-free Graphite primary gasket Metal-to-Metal SealingWhen non-meatl sealing isdeteriorated by fire,ball floats to shut off the line fruid easily for installation of gear, motor or pneumatic actuator 123456789Body Closure Ball Yoke Gland Flange Seat Ring Stem Gland Gasket 101112131415161718Grounding Washer Packing Set Thrust Washer Stud Nut Bolt Bolt Spring Steel BallSeries FB2 material specifications Series FB2 Ball Valve Two-piece,split body,cast steel,side entry design Full Port Size in D mm L mm H mm W mm Weight Kg Reduced Port Size in D mm L mm H mm W mm Weight Kg d mm 150L B Gear Operator Dimensions W H D L Full Port WH d D L Reduced Port W 123456789101112131415161718No. Part Standard Stainless Steel Sour Service Low TemperatureServiceASTM A352-LCB ASTM A352-LCB ASTM A182-F316ASTM A216-WCB ASTM A216-WCB PTFE ASTM A182-F316ASTM A182-F316316SS + Graphite Graphite PTFE PTFE ASTM A320-L7M ASTM A194-7M ASTM A320-L7M ASTM A320-L7M S.S.S.S.ASTM A216-WCB ASTM A216-WCB ASTM A105/ENP ASTM A216-WCB ASTM A216-WCB PTFE ASTM A182-F6a ASTM A276-420316SS + Graphite Graphite PTFE PTFE ASTM A193-B7M ASTM A194-2HM ASTM A193-B7M ASTM A193-B7M S.S.S.S.ASTM A351-CF8M ASTM A351-CF8M ASTM A182-F316ASTM A351-CF8M ASTM A351-CF8M PTFE ASTM A182-F316ASTM A182-F316316SS + Graphite Graphite PTFE PTFE ASTM A193-B8ASTM A194-8ASTM A193-B8ASTM A193-B8S.S.S.S.ASTM A216-WCB ASTM A216-WCB ASTM A105/ENP ASTM A216-WCB ASTM A216-WCB PTFE ASTM A182-F6a ASTM A276-420316SS + Graphite Graphite PTFE PTFE ASTM A193-B7ASTM A194-2H ASTM A193-B7ASTM A193-B7S.S.S.S.Body Closure Ball Yoke Gland Flange Seat Ring Stem Gland Gasket Grounding Washer Packing Set Thrust Washer Stud Nut Bolt Bolt Spring Steel Ball 1 / 23 / 411-1/222-1/23456810121 / 2131925385164761021251522032543051310811712716517819120322935639445753361014059637697107142152178252272342345479591301301602302304004007001100 300 * 300 * 400 * 600 *1303/4*1/2*3/43/4*1/2*3/41*3/4*11-1/2*1-1/22*1-1/2*22-1/2*2*2-1/23*2-1/2*34*3*46*4*68*6*810*8*1012*10*121.782.003.517.2311.0515.022.036.058.0110.0195.0309.0346.02.29131925385164761021522032541319253851647610215220325430519117127165178190203229394457530610152828510011512015316219129034044282130130160230230400400460 300 * 300 * 400 *130 3.04.57.09.515.016.029.548.0123.0212.0230.03.5Series FB2 Ball Valve122019178111354197161021181631415296Blow-out Proof Stem Internally insertedand functions as the backseat for assured stem sealing at all pressuresSeries FB2 Ball Valve Two-piece, split body, forged steel, side entry design This series ball valves are featured with two-piece bolted with flanged end body and floating ball. Body and closure are fully forged steel made which eliminate the inevitable casting defects and is ideal for high pressure service. FB2 series ball valves are available in size from 1 /2 to 4 and offers ANSI class rating 600 to 2500, all meet the fire safe requirements of BS 6755 and API 607. Blowout-proof stem, anti-static device and locking device are standard design, low emission packing with live loaded gland flange design can be available upon request. Manual handle operation is basic standard, but fully machined mounting pad can also easily install with gear, motor or pneumatic operator.ANSI Class 150 to 300 and Three-piece design can be supplied upon request.Double "D" Stem HeadProvides mounting of the lever handle always in parallel to the flow passageSecure LIne Flow Equipped with an integral locking device to secure the line flow Spring-loaded pins installed on ball, stem is provided to ensure electrical continuity throughout the valve Bolted Body/AdapterFlanged body and flanged adapter secured with cap screws to maintain seal integrity Metal-to-Metal SealingWhen non-meatl sealing is deteriorated by fire,ball floats to shut off the line fruid Index no Part 1234567891011Body Closure Ball Lever Lever Sleeve Seat Ring Stem Gland Gasket Steel Ball Packing Set Index no Part 12131415161718192021Stop Plate Thrust Washer Stud NutSpringSpring Washer Stop Pin Nut WasherLocking Plate Series FB2 Ball ValveThis is a typical Series FB2 floating ball valve illustrated cross-section drawing which is only fordemonstrating of basic design features. The actual product design may be slightly different from this sample drawing due to its size and pressure class.Series FB2 material specifications Series FB2 Ball Valve 123456789101112131415161718192021No. Part Standard Stainless Steel Sour Service Low TemperatureServiceBody Closure Ball Lever Lever Sleeve Seat Ring Stem Gland Gasket Steel Ball Packing Set Stop Plate Thrust Washer Stud Nut Spring Spring Washer Stop Pin Nut Washer Locking Plate ASTM A105ASTM A105ASTM A105/ENP Carbon Steel Polyethylene PTFE ASTM A182-F6a ASTM A276-420Graphite S.S.PTFE Carbon Steel PTFE ASTM A193-B7M ASTM A194-2HM S.S.Alloy Steel Carbon Steel Carbon Steel Carbon Steel Carbon Steel ASTM A350-LF2ASTM A350-LF2ASTM A182-F316Carbon Steel Polyethylene PTFE ASTM A182-F316ASTM A182-F316316 + Graphite S.S.PTFE S.S.PTFE ASTM A320-L7M ASTM A194-7M S.S.Alloy Steel S.S.S.S.S.S.S.S.ASTM A182-F316ASTM A182-F316ASTM A182-F316Carbon Steel Polyethylene PTFE ASTM A182-F316ASTM A182-F316Graphite S.S.PTFE S.S.PTFE ASTM A193-B8ASTM A194-8S.S.Alloy Steel S.S.S.S.S.S.S.S.ASTM A105ASTM A105ASTM A105/ENP Carbon Steel Polyethylene PTFE ASTM A182-F6a ASTM A276-420Graphite S.S.PTFE Carbon Steel PTFE ASTM A193-B7ASTM A194-2H S.S.Alloy Steel Carbon Steel Carbon Steel Carbon Steel Carbon Steel Two-piece,split body,forged steel,side entry design L W H D H Dd WL Dimensions Full Port Size in D mm L mm H mm W mm Weight Kg Reduced Port Size in D mm L mm H mm W mm Weight Kg d mm 600L B B Full Port Reduced Port 3/4*1/2*3/4713131921622970831401707.510.01/2*1/4*1/21 / 23 / 41319216229831121701708.511.01 / 23 / 411-1/2234131925385176102165191216241292356432668890120135180224160170170280300450500 3.55.16.513.229.034.0135.53/4*1/2*3/41*3/4*11-1/2*1*1-1/22*1-1/2*23*2*3713192538517613192538517610216519121624129235643243668890120135180130160170170280300450 2.93.85.310.61342.081.51/2*1/4*1/24*3*4Series FB2 Ball ValveSeries FB2 Ball Valve Series BC Ball Valve Two-piece,split body,forged steel,side entry designL W HD WLHDd DimensionsFull Port Size in D mm L mm H mm W mm Weight Kg Reduced PortSizein D mm L mm H mm W mm WeightKgd mm150LBFull Port Reduced Port1 / 23 / 411-1/22313192538517621622925430536847083112123143177200230230300400450700 6.811.016.032.664.090.0713264751708.01/2*1/4*1/21 / 213264882309.03/4*1/2*3/41*3/4*11-1/2*1*1-1/22*1-1/2*23*2*37131925385113192538517621622925430536847070831121231431771702302303004004507.510.015.028.041.082.01/2*1/4*1/2NEWAY trunnion mounted ball valve contains 3 main series: TB2 series for cast steel two-piece design, TB3 series for forged steel three-piece design and TTE series for top entry uni-body design, all designed conform to API 6D and fire safe test are satisfied to BS 6755 and API 6FA. They are available in size from 2to 48Wide range of body and trim material is available for service00temperature from -46C to 200C and pressure rating from ANSI class 150 to 1500 or for sour service to NACE Mr0175.For 6 inch and larger NEWAY Trunnion mounted ball valveswill be installed with a sealant injection fittings on both stemand seats. When the sealing materials (seat sealing or stemo-ring) are damaged or decomposed by fire or otheraccidental causes, leakage from the seat and stem can beprevented by injection of sealant into these fittings. Fitting isalso internally installed a second check valve to providesbackup sealing. Emergency sealant injection system Cavity Pressure ReliefEach ball seats shut off the line fluid independently on the upstream and downstream side, allowing double block o p e r a t i o n. W h e n t h e p r e s s u r e i s simultaneously applied to both sides of the ball in closed position, the valve bore and the body cavity will be isolated from each other, and the residue within the body cavity can be released through the drain plug.Double block and bleed Top flange Injection Closure Gland Body Ball SeatThe stem is made separately from the ball; The lover end of the stem is designed with an integral collar to be blowout-proof.Antistatic device is a standard feature of NEWAY ball valve . A spring-loaded pin assures the electrical continuity, between ball ,stem and body, so as to avoid sparks during turning of the stem to open and close the valve, which could be dangerous in caseof hazardous area installation.Super Fire safe designExternal leakage preventionLeakage from the valve stem area isprevented by double sealing with 2 O-rings and gland gasket. Leakagethrough the valve body joint is alsoblocked by double sealing with O-ringand body gasket. After a fire hasdeteriorated O-rings, gland gasket,body gasket and stem firesafe packingare the measure that prevents externalfluid leakage. When non-metal materials such as O-ring, seat insert and spacer aredecomposed or deteriorated by fire, theedge of the metal seat preloaded by theBall to shut off the line fluid to minimize internal leakage through the valve bore. Also the fire safe flexible graphite seat packing will be compressed by the seat spring to prevent fluid leakage Internal leakage preventionAnti Blow-out Stem Anti-static Device Top Flange Stem Stem fire safe packingGland O-ring Gland gasket Body Ball Anti-static spring Grounding plunger Drain plug Body Upstream seat Body cavity Closed ball Vent valve Downstream seat Body cavity Total spring force (Fs)Cavity pressure (Pc)Fig b. P*D1>FsP=Pc-Pl Cavity pressure (Pc)Total spring force (Fs)Fig a. P*D1<Fs P=Pc-Pl Stem Top Flange Gland Body Closure O-ring Ball Gland gasket Body gasket Stem firesafe packing Trunnion Mounted Ball ValveDesign FeatureTrunnion Mounted Ball Valve Design FeatureH L Dd W H L D d d mm L mm H mm W mm D mm L mm H mm W mm d mm 517610215220325430533738743843848976102152203254305337387438489540591203229394457533610686762864914101610671651932313293933934414815986436437082304004004601000*500*500*500*500*500*500*500304790161268467560766902113013001520234681012141618202224517610215220325430533738743848954059125121616523018178203229394457533610686762864914101610671651932313293934014414815986437087988632304004601000*500*500*500*500*500*500*500*500*500173350931662734755707789351190134615795176283165230383*2*34*3*46*4*68*6*810*8*1012*10*1214*12*1416*14*1618*16*1820*18*2022*20*2224*20*243*2*3WD mm L mm H mm W mm D mm L mm H mm W mm d mm 51761021522032543053373874384897610215220325430533738743848959135643255966078783888999110921194139717624727636336342654859864874081040075010001500*500*500*500*500*500*500*5004170122255440662010601440186024003240 600L B 234681012141618202451761021522032543053373874384895912351763683811922794601000529729235643559660787838889991109211941397217624727636336342654859864874081092040075010001500*500*500*500*500*500*500*500*500275080251.835060082011301550210028003626517676102381457192279460100083103--------------3*2*34*3*46*4*68*6*810*8*1012*10*1214*12*1416*14*1618*16*1820*18*2024*20*243*2*34*3*4W HL D d L H D d WTwo-piece,split body,cast steel,side entry design Full PortSizeinWeight Kg Reduced Port Size in Weight Kg DimensionsGear Operator Series TB2 Ball Valve Series TB2 Ball ValveTow-piece,split body,cast steel,side entry design Gear OperatorFull Port Size in Weight Kg Reduced Port Size in Weight Kg Dimensions 150L BWDdHWDdHLL22328201315652919810383733341426161127918363538724251221173231302230311Series TB3 Ball ValveIndex noPart12345678910111213141516171819Body Closure BallSeat Assembly( )Seat Insert Seat Ring StemTrunnion Alignment Pin ShimTrunnion Support Gasket Body Gasket Spacer GasketFiresafe Gasket Gland Cap Top Flange Thrust Washer BearingIndex noPartSeat Follower Vent Valve Drain Seat Spring Grounding Spring Grounding Plunger O-Ring O-Ring O-Ring Series TB3 Ball ValveD mmL mmH1mm2346810121416182022242651761021522032543053373884384895405916351782032293944575346106867628649149911067114320030031533540542746550662266673083389590011012616516520022026229334192435480518535265285285*300*300*300*500*600*600*600*600*600*800*80021.1132.0992190345495577859114414401918235228033200W mmH2mmSize inD mmL mmH1mmW mm3*2*34*3*46*4*68*6*810*8*1012*10*1214*12*1416*14*1618*16*1820*18*2022*18*2224*20*2426*22*2628*24*28d mm517610215220325430533738743843848954059176102152203254305337387438489540591635686203229394457534610686762864914991106711431245200300315335405427465506622666666730833895110126165170200220262293341392392435480518265285285*300*300*300*500*600*600*600*600*600*600*80026.4540102225373509730790109511522343206022152700H2mmWH 1H 2DdWLSeries TB3 Ball ValveSeries TB3 material specifications 123456789101112131415161718192021222324252627No. Part Standard Stainless Steel Sour Service Body Closure BallSeat Assembly Seat Insert Seat Ring Stem Trunnion Alignment Pin ShimTrunnion Support Gasket Body Gasket Spacer Gasket Firesafe Gasket Gland Cap Top Flange Thrust Washer Bearing Seat Follower Vent Valve Drain Seat Spring Grounding Spring Grounding Plunger O-Ring O-Ring ASTM A105ASTM A105ASTM A105/ENPAssembled By No.5&625% Glass-filled PTFE ASTM A105/ENP ASTM A105/ENP ASTM A182-F316ASTM A182-F316ASTM A216-WCB/ENP 316SS + Graphite 316SS + Graphite PTFE316SS + Graphite 316SS + Graphite ASTM A105ASTM A105316 + PTFE + MoS2316 + PTFE + MoS2ASTM A105/ENP Assembly S.S.Inconel X-750S.S.ASTM A182-F316NBR NBR ASTM A182-F316ASTM A182-F316ASTM A182-F316Assembled By No.5&625% Glass-filled PTFE ASTM A182-F316ASTM A182-F316ASTM A182-F316ASTM A182-F316ASTM A351-CF8M 316SS + Graphite 316SS + Graphite PTFE316SS + Graphite 316SS + Graphite ASTM A182-F316ASTM A182-F316316 + PTFE + MoS2316 + PTFE + MoS2ASTM A182-F316Assembly S.S.Inconel X-750S.S.ASTM A182-F316NBR NBR ASTM A105ASTM A105ASTM A105/ENPAssembled By No.5&625% Glass-filled PTFE ASTM A105/ENP ASTM A105/ENP ASTM A182-F316ASTM A182-F316ASTM A216-WCB/ENP 316SS + Graphite 316SS + Graphite PTFE316SS + Graphite 316SS + Graphite ASTM A105ASTM A105316 + PTFE + MoS2316 + PTFE + MoS2ASTM A105/ENP Assembly S.S.Inconel X-750S.S.ASTM A182-F316NBR NBR ASTM A350-LF2ASTM A350-LF2ASTM A350-LF2/ENPAssembled By No.5&625% Glass-filled PTFE ASTM A350-LF2/ENPASTM A350-LF2/ENP ASTM A182-F316ASTM A182-F316ASTM A352-LCB/ENP316SS + Graphite 316SS + Graphite PTFE316SS + Graphite 316SS + Graphite ASTM A350-LF2ASTM A350-LF2316 + PTFE + MoS2316 + PTFE + MoS2ASTM A350-LF2/ENP Assembly S.S.Inconel X-750S.S.ASTM A182-F316NBR NBR Low TemperatureServiceDimensionsClass 150LB Full PortSize inWeight KgClass 150LB Reduced portWeight KgGear OperatorThree-piece,split body,forged steel,side entry designD mmL mmH1mm234681012141618202224285176102152203254305337388438489540591686292356432559660787838889991109211941295139715492063153303454154274655196386837488549179581131291691481852262693003504024464925315564007501000*300*300*500*600*600*600*600*600*800*800*8003363.5117273.54527366251230153521352640337049206060W mmH2mmD mmL mmH1mmW mm3*2*34*3*46*4*68*6*810*8*1012*10*1214*12*1416*14*1618*16*1820*18*2022*18*2224*20*2428*24*3030*24*28d mm5176102152203254305337387438438489591591761021522032543053373874384895405916867373564325596607878388899911092119412951397164916512063153303454154274655196386836837489179171131291691481852262693003504024021165315314007501000*300*300*500*600*800*800*600*600*600*600*60046.59917630453690210901310164022702430344042504730H2mmH 1H 2LH 1H 2LD dWKgD mmL mmH1mm2346810121416182022242851761021522032543053373884384895405916862162833054045025696487628399169911093 11431347206315330345415427465519638683748854917958113129169148185226269300350402446492531556265400750*300*300*400*500*600*600*600*600*600*800*800311121137651775890013501715209022202890457545.68W mmH2mmD mmL mmH1mmW mm3*2*34*3*46*4*68*6*810*8*1012*10*1214*12*1416*14*1618*16*1820*18*2022*18*2224*20*2428*24*2830*24*30d mm5176102152203254305337387438438489591591761021522032543053373874384895405916867372833054045025696487628399199911093114313471397206315330345415427465519638683683748917917113129169148185226269300350402402446531531265400750*300*300*500*600*600*600*600*600*600*800*8003655103222381619830970153018302010222032003200H2mmWH 1H 2DdWLH 1H 2Series TB3 Ball ValveDimensionsClass 300LB Full PortSize inWeight KgClass 300LB Reduced PortSize inWeight Kg Gear OperatorDimensionsClass 600LB Full PortSize inWeight KgClass 600 LB Reduced PortSize inGear OperatorThree-piece,split body,forged steel,side entry designThree-piece,split body,forged steel,side entry design Series TB3 Ball ValveWLH 1H 2DdH 1H 2LDdW337302332322330174140826273181665562573325371412213813212810223534362843299391525Series TTE Ball Valve Series TTE Ball ValveWH 1H 2LDd H 1H 2DmmL mm2346810121416182024385176102152203254305337388438489591H2mmW mm701101101751952802853203404104455106404004007501000*300*300*500*600*600*600*600*600*600303880150248438601625123015352135264039602412923564325596607878388899911092119413971-1/2209195240280305400435440505590700775840H1mmD mmL mm2*1-1/2*23*2*34*3*46*4*68*6*810*8*1012*10*1214*12*1416*14*1618*16*1820*18*2024*20*24d mm3851761021522032543053373874384895176102152203254305337387438489591292356432559660787838889991109211941397H2mmW mm701101101751952802853203404104455104004007501000*300*300*500*600*600*600*600*60040549921230451090210901310164024303440209195240280305400435440505590700775H1mm12345678910111213141516171819202122232425262728293031No. Part Standard Stainless Steel Sour Service Body Closure BallSeat Assembly Seat Insert Seat Ring Spring Seat Stem Shim Gasket Gasket Gasket Gland Cap Top Flange Thrust Washer Shim Bearing Bearing Vent V alve DrainRetainer Ring Retainer Ring Retainer Ring Retainer Ring Seat Spring Grounding Spring Grounding Plunger O-Ring O-Ring O-Ring O-Ring ASTM A216-WCB ASTM A105ASTM A105/ENPAssembled By No.5&6Nylon 1010 + 5% MoS2ASTM A105/ENP ASTM A105/ENP ASTM A105/ENP ASTM A182-F316316SS + Graphite 316SS + Graphite 316SS + Graphite ASTM A105ASTM A105316 + PTFE + MoS2316 + PTFE + MoS2316 + PTFE + MoS2316 + PTFE + MoS2Assembly S.S.PTFE PTFE PTFE PTFEInconel X-750S.S.ASTM A182-F316NBR NBR NBR NBR ASTM A351-CF8M ASTM A182-F316ASTM A182-F316Assembled By No.5&6Nylon 1010 + 5% MoS2ASTM A182-F316ASTM A182-F316ASTM A182-F316ASTM A182-F316316SS + Graphite 316SS + Graphite 316SS + Graphite ASTM A182-F316ASTM A182-F316316 + PTFE + MoS2316 + PTFE + MoS2316 + PTFE + MoS2316 + PTFE + MoS2Assembly S.S.PTFE PTFE PTFE PTFEInconel X-750S.S.ASTM A182-F316NBR NBR NBR NBR ASTM A216-WCB ASTM A105ASTM A105/ENPAssembled By No.5&6Nylon 1010 + 5% MoS2ASTM A105/ENP ASTM A105/ENP ASTM A105/ENP ASTM A182-F316316SS + Graphite 316SS + Graphite 316SS + Graphite ASTM A105ASTM A105316 + PTFE + MoS2316 + PTFE + MoS2316 + PTFE + MoS2316 + PTFE + MoS2Assembly S.S.PTFE PTFE PTFE PTFEInconel X-750S.S.ASTM A182-F316NBR NBR NBR NBR ASTM A352-LCB ASTM A350-LF2ASTM A350-LF2/ENPAssembled By No.5&6Nylon 1010 + 5% MoS2ASTM A350-LF2/ENP ASTM A350-LF2/ENP ASTM A350-LF2/ENP ASTM A182-F316316SS + Graphite 316SS + Graphite 316SS + Graphite ASTM A350-LF2ASTM A350-LF2316 + PTFE + MoS2316 + PTFE + MoS2316 + PTFE + MoS2316 + PTFE + MoS2Assembly S.S.PTFE PTFE PTFE PTFEInconel X-750S.S.ASTM A182-F316NBR NBR NBR NBR Low TemperatureServiceSeries TTE material specifications Top entry, trun nion mounted designDimensionsGear OperatorClass 600LB Full PortSize inWeight KgClass 600LB Reduced PortSize inWeight KgSeries TTE Ball ValveSeries TTE Ball Valve。

® U.S. Registered TrademarkCopyright © 2015 Honeywell Inc. • All Rights ReservedEN0B-0717GE51 R1115VBGx-xx-xx Externally Threaded Control Ball ValvesPN25 (DN15 TO DN32)SPECIFICATION DATAAPPLICATIONThe VBG2 2-Way and VBG3 3-Way Control Ball Valves control hot and chilled water with glycol solutions up to 50% according to VDI2035 in heating, ventilating, and air conditioning (HVAC) systems to provide two-position or modulating functions.Features∙ Sizes from DN15 to DN32 with external (male) BSPP(G) connections 1" to 2".∙ Equal percentage flow characteristic.∙ Compatible MVN Rotary Valve Actuators: 2-position,floating, modulating, non-spring return.∙ Removable manual operating handle to control valveduring installation or in the event of power failure. ∙ Actuator can be mounted on the valve in any of fourorientations.∙ Wide range of k VS choices from 0.25 to 25. ∙ Nickel-chrome plated brass ball.∙ Valve installs in a globe valve "T" pattern, no extraelbows or piping required.∙ Mixing or diverting control for 3-way valves.∙ Leakage rate A, air bubble-tight (according to EN12266-1).SpecificationsValve type Control Ball Valve Body pattern 2-way (VBG2-xx-xx),3-way (VBG3-xx-xx)Nominal pressure rating PN25Media temperature range +5 … +120 °C (+41 … +248 °F) Connection type Male BSPP, threadedconnections, flat sealingControlled fluid Chilled or hot water according toVDI2035 with up to 50% Glycol. Not for use with steam or fuels.Leakage rating VBG2 Leakage rate A, air bubble-tightaccording to EN 12266-1VGB3 Leakage rate A, air bubble-tightaccording to EN 12266-1 for A-AB port, Rate I according to EN 1349 and EN 60534-4 for B-AB port (0.1% of kV)Capacity index (k vs ) see Table 1 and Table 2 Close-off pressures see Table 1 and Table 2 Materials:Body DZR Brass Stem BrassBall Chrome-plated brass Seat Teflon® seals with EPDM O-rings Flow control insert Noryl®Body Style:2-way ball valve Straight-through flow, full orreduced port using patented flow control insert3-way ball valve A-B-AB flow, full or reduced portusing patented flow control insertBody pressure rating PN25Flow Characteristics: 2-way Equal percentage with flowcontrol insert3-way Port A to AB: Equal percentage;Port B to AB: LinearApprovals/Standards CEVBGx-xx-xx EXT. THREADED CONTROL BALL VALVES PN25 (DN15 TO DN32) – SPECIFICATION DATAEN0B-0717GE51 R1115 2Table 1. VBG2 Two-way control ball valvesDN K vs A-BO.S. no.Close-off pressure with MVNRotary Valve Actuators (kPa)External threadsize150.25 VBG2-15-0.25 890 1"0.4 VBG2-15-0.4 0.63 VBG2-15-0.631 VBG2-15-11.6 VBG2-15-1.62.5 VBG2-15-2.5 4 VBG2-15-4 6.3 VBG2-15-6.3 204 VBG2-20-4890 1 ¼" 6.3 VBG2-20-6.3 8.6 VBG2-20-8.6 256.3 VBG2-25-6.36801 ½"10 VBG2-25-10 16 VBG2-25-16 25 VBG2-25-2532 16 VBG2-32-16 2" 25 VBG2-32-25Table 2. VBG3 Three-way control ball valvesDN k vs A-B k vs B-AB O.S. no.Close-off pressure with MVNRotary Valve Actuators (kPa) External thread size150.63 0.5 VBG3-15-0.63 3401"1 0.8 VBG3-15-11.6 1.28 VBG3-15-1.62.5 2 VBG3-15-2.5 43.2 VBG3-15-4 6.3 5.04 VBG3-15-6.3 204 3.2 VBG3-20-41 ¼" 6.3 5.04 VBG3-20-6.3 8.6 6.88 VBG3-20-8.6 256.3 5.04 VBG3-25-6.31 ½"10 8 VBG3-25-10 16 12.8 VBG3-25-1632 16 12.8 VBG3-32-16 270 2"25 20 VBG3-32-25VBGx-xx-xx EXT. THREADED CONTROL BALL VALVES PN25 (DN15 TO DN32) – SPECIFICATION DATA3 EN0B-0717GE51 R1115V B G 12552BALL VALVEMALE EXT. THREAD2-WAY 3-WAY2:3:25:15:0.25:0.4:0.63:1:1.6:2.5:4:6.3:8.6:10:16:25:DN25DN15Kvs = 0.25Kvs = 0.4Kvs = 0.63Kvs = 1Kvs = 1.6Kvs = 2.5Kvs = 4Kvs = 6.3Kvs = 8.6Kvs = 10Kvs = 16Kvs = 25DN32DN2032:20:Fig. 1. VBG product keyTable 3. Valve accessories and replacement partsPart no.Description5112-19 Replacement stem assembly for VBG, DN15-20 5112-20 Replacement stem assembly for VBG, DN25-32MVNAAAReplacement valve adaptor, standard profile, pre-assembled on the VBG valves AC-15TF-1 Fittings accessories DN15 VBG valves AC-20TF Fittings accessories DN20 VBG valves AC-25TF Fittings accessories DN25 VBG valves AC-32TF Fittings accessories DN32 VBG valvesTable 4. Connection sets ConnectionPipe size DN O.S. no. Connection setDescriptionInternal threadR ½"15 AC-15TF-1Consisting of 1union nut, 1 tail-piece, and 1 gasketR ¾" 20 AC-20TF R 1" 25 AC-25TF R 1-¼"32AC-32TFTable 5. Connection set dimensionsConnection setacO.S. no.G 1" G 1/2" AC-15TF-1 G 1-1/4" G 3/4" AC-20TF G 1-1/2” G 1" AC-25TF G 2” G 1-1/4"AC-32TFVBGx-xx-xx EXT. THREADED CONTROL BALL VALVES PN25 (DN15 TO DN32) – SPECIFICATION DATAEN0B-0717GE51 R1115 4Table 6. VBG2 dimensions (in mm)DNA B C D G H I J K O15 74.0 67.1 19.1 48.0 G1" 92.3 71.0 142.1 123.0 36.0 20 85.5 77.2 24.7 52.7 G1¼" 98.05 71.0 152.2 127.7 46.0 25 84.5 84.1 26.8 57.5 G1½" 97.55 71.0 159.1 132.5 50.0 32 102.0 98.1 36.0 63.4 G2" 106.3 71.0 173.1 138.4 65.0Table 7. VBG3 dimensions (in mm) DNA B C D E G H IJ K O15 74.0 107.1 41.1 49.144.0G1"92.371.0182.1 124.141.020 85.5 109.4 46.9 49.149.5G1¼"98.0571.0184.4 124.146.025 84.5 118.4 44.4 53.153.5G1½"97.5571.0193.4 128.150.032 107.5 142.3 50.9 63.069.0G2"109.0571.0217.3 138.065.0VBGx-xx-xx EXT. THREADED CONTROL BALL VALVES PN25 (DN15 TO DN32) – SPECIFICATION DATA5 EN0B-0717GE51 R1115MountingWhen installing the valve care must be taken that the flow direction is correct (see section "Typical Operation" below). The valve must not be mounted with the stem pointing downward.The valve is supplied complete with mounting instructions. The water quality must meet VDI 2035 requirements. NOTE:Mount the actuator by hand, only. Do not use a tool, as this could result in damageTypical OperationAll types of valves should be mounted in the return flow. If the Dp-values exceed 300 kPa, attention should be paid to the development of noise.Two-Way ValvesDirection of flow always from port A to port BThree-Way ValvesThese valves are used preferably as mixing valves. This means:Port AB: Total flow outlet Port A: Controlled flow inletManufactured for and on behalf of the Environmental and Combustion Controls Division of Honeywell Technologies Sàrl, Rolle, Z.A. La Pièce 16, Switzerland by its Authorized Representative:Automation and Control Solutions Honeywell GmbH Böblinger Strasse 1771101 Schönaich, Germany Phone +49 (0) 7031 637 01 Fax +49 (0) 7031 637 740 EN0B-0717GE51 R1115Subject to change without noticeDISPOSAL OF VBG CONTROLL BALL VALVESOBSERVE LOCAL REQUIREMENTS ON PROPER WASTE RECYCLING / DISPOSAL!∙ Dezincification-resistant brass body ∙ Chrome-plated brass ball∙ Teflon® seals with EPDM O-rings ∙ Noryl® flow control insert。

PTFE-lined valves V a l v e s f o r c o r r o s i v e a n d t o x i c a p p l i c a t i o n sAggressive acids and alkalis pose a challenge to many processes. It is all the more important to be able to rely on safe, proven and reliable products.Butterfly valves, ball valves and check valves from InterApp guarantee economical and safe operation over the entire service life.Valves for corrosive and toxic applicationsBody construction Wafer, Lug, U-Section Nominal diameter DN 32—900Max. working pressure Up to 16 barFlange connection PN10, PN16, ANSI cl. 150, AS 2129 Table D & E and others Temperature range –20°C up to 200°C Body materialDuctile iron, stainless steelDisc-shaft (one piece) materialStainless steel PFA overmoulded, Stainless steel PFA antistatic overmoulded, Stainless steel, Stainless steel polished Ra <0.8, Stainless steel polished Ra <0.4 and Fe <1% , Super Duplex, Super Duplex polished Ra <0.8, Hastelloy,Hastelloy polished Ra <0.8Liner materialPTFE, PTFE antistatic, Ultraflon ®, Ultralene™,Fluoroplastomer according to FDA 177.1550 and EU no. 10/2011Special executionHigh-purity, LABS-free and for explosive atmospheresPTFE Lined Butterfly Valves—BiancaPTFE lined centric butterfly valve for corrosive fluids and high-purity applications.1ReliabilityThe high liner collar, the PFA disc overmoulding on the shaft and the life-preloaded safety shaft sealing guarantee excellent shaft sealing.4TightnessThe spherically machined liner in the pole area improves life-time and tightness at the pole region. It is available in PTFE, PTFE antistatic, Ultraflon ® and Ultralene™.2Total diffusion resistanceThe PFA disc encapsulation and advanced liner material of at least 3 mm facilitate a total diffusion resistance.5Increased service lifeThe chambered liner prevents cold flow at the flange sealing surface.3Entire corrosion resistanceOne piece disc/shaft ensures anentire corrosion resistance as well as a blow-out proof shaft and excellent Kv values.6Product varietyThe Bianca butterfly valve from DN 32 up to 900 can be configured for a wide range of applications.Extremely safe and reliableThe Bianca butterfly valve offers consistent reliability and convinces with its superior technical features.Body construction 2- or 3-piece body Connections Flanged ends Nominal diameter DN 15 —100Max. working pressure up to 16 bar Max. working temperature –50°C up to 180° CFlange connection PN6, PN10, PN16, ANSI cl. 150Face to face dimension DIN3202-F1/EN556-1, ANSI B16.10Top flange According to ISO 5211Body material Carbon steel, epoxy coated with PFA and PFA antistatic body lining Seat ring material PTFE, PTFE antistatic, PTFE GF reinforcedBall material PTFE, PTFE antistatic, PTFE GF reinforced, ceramic Special executionCavity filler seats (very low dead volume)PTFE Lined Ball Valves—2-way full bore PTFE lined ball valves with flanged ends for corrosive applications. The range includes models with handlever or ISO top flange.Other ball valves—TLBVH222-piece body, handlever operated—TLBVH233-piece body, handlever operated—TLBVH23A3-piece body, handlever operated ANSI cl. 150—TLBVA233-piece body, ISO top flange—TLBVA23A3-piece body, ISO top flange ANSI cl. 150Pneumatic Actuators—IA motionType Pneumatic actuator Function Double and single actingNominal torque 15–10007 Nm (double acting at 6 bar air supply)Supply pressure 3–8 bar (IA1000D 3–7 bar)Temperature range–40°C up to 80°CInterApp offers various accessories for actuators, such as solenoid valves for pneumatic actuators, position indicators (limit switches open mounted and limit switch boxes), analog and digital positioners, air flow regulators and silencers.Wafer Poppet Check Valve—Nominal diameter DN 15-100Max. working pressure Up to 16 barFlange connection PN10, PN16, ANSI cl. 150Max. working temperature -20ºC up to 200ºCBody material Carbon steel, Stainless steel Poppet material PTFE Seal material PFASpecial executionsAlternative pressure ratings, PTFE encapsulated,alternative spring materials, without spring (floating poppet)WPCVWafer poppet check valve with guided spring and poppet for a wide range of process applications.Flanged Poppet Check Valve—Nominal diameter DN 25-100Max. working pressure Up to 16 barFlange connection PN10, PN16, ANSI cl. 150Max. working temperature -20ºC up to 200ºCBody material Carbon steel, Stainless steel Poppet material PTFESeal material PFA, PFA conductiveSpecial executionsAlternative pressure ratings, PTFE encapsulated,alternative spring materials, without spring (floating poppet)FPCVFlanged poppet check valve with flanged ends for use in the most demanding corrosive and toxic applications.Swing Check Valve—Nominal diameter DN 150-300Max. working pressure Up to 16 barFlange connection PN10, PN16, ANSI cl. 150Max. working temperature -20ºC up to 200ºC Body material Cast steel Disc material Cast steel Seal material PFASpecial executionAntistatic liner, soft seats Kalrez ® & Viton ® for gas applicationsSTCVSwing check valve with fully encapsulated one piece disc/hinge assembly for a wide range of chemical process applications.Ball Check Valve—Nominal diameter DN 15-100Max. working pressure Up to 16 bar Flange connection PN10, PN16Max. working temperature -50 °C up to 180°CBody material Carbon steel, Stainless steelBall material PTFE, PTFE antistatic, PTFE GF reinforced, ceramic Seal material PFASpecial executionAntistatic, cavity filter seats (very low dead volume)TLBCVFull bore ball check valve with flanged ends and 3-piece body for corrosive applications.A d e d i c a t e d m e m b e r o f t h e G r o u pInterApp AGGrundstrasse 246343 RotkreuzTel. +41 41 798 22 33****************.net Globally local. As a global production and distribution company, we offer the advantage of a comprehensive portfolio of products and solutions. Thanks to our local presence we are also the ideal consultant as we are familiar with your needs in every project phase and support you with efficient planning services.。

83-2R-20220525Copyright 2013 A-T Controls, Inc.SERIES 83 3-PieceTriac 83 Series 3-Piece Ball Valves are thefinest quality 3-piece valves on the market. The high quality investment castings feature a fully machined bore. The superior live-loaded packing system is accomplished with Belleville washers,“V” ring packing and a unique primary pyramidal stem seal. This advanced sealing system provides protection against stem leaks experienced by ordinary ball valves.RTFE seats are standard,but various options are availablefor seat materials. The 50/50STFE seat option is excellentfor services that call for highertemperatures and more difficultapplications including steam.Call us for details.Easy to Automate!See automated data sheets for pre-sized assembliesCincinnati, Ohio 45246 PHONE (513) 247-5465 FAX (513) 247-5462********************Pneumatic ElectricHigh Performance, Full Port 3-Piece Ball ValveISO 5211 Mounting Pad Classes up to 6001500 - 2000 psi(by size)* 1/4” THRU 2” QTY = 4 PCS* 2-1/2” QTY = 6 PCSHigh Performance, Full Port 3-Piece Ball ValveISO 5211 Mounting Pad Classes up to 600 1500 - 2000 psi (by size)Other options available—call for details.Actuators are sized based on clean/clear fluid.SAMPLE PART #Carbon Steel End ConnectionValve SeriesSeat MaterialValve Size TRIAC Actuator SeriesActuator Size Double ActingSolenoid Limit Switch83C-TX-100/2R2D-XX9955 International Blvd.Cincinnati, Ohio PHONE (513) 247-5465FAX (513) 247-5462********************DIMENSIONS SHOWN ARE FOR ASSEMBLIES SIZED FOR 80 PSI SUPPLYSERIES 83 3-Piece DIMENSIONS (IN)Other options available—call for details.Actuators are sized based on clean/clear fluid.SAMPLE PART #Carbon Steel End Connection Valve Series Seat Material Valve Size TRIAC Actuator Series Actuator Size Double Acting Solenoid Limit Switch 83C-TX-100/2R2D-XX 83DA-20150928Copyright 2013 A-T Controls, Inc.See valve part number matrix for complete partnumber and options.SERIES 83 3-PieceSERIES 83 3-Piece Other options available—call for details.Actuators are sized based on clean/clear fluid.83Series_20200812 | Copyright 2013 A-T Controls, Inc. | | (513) 247-5465SAMPLE PART #Carbon SteelEnd ConnectionValve SeriesSeat MaterialValve SizeTRIAC Actuator SeriesActuator Size Spring ReturnSolenoidLimit Switch 83C-TX-050/2R2S-XX9955 International Blvd.PHONE (513) 247-5465See valve part numbermatrix for complete partnumber and options.Other options available—call for details.Actuators are sized based on clean/clear fluid.SERIES 83 3-Piece83EL-20150928Copyright 2013 A-T Controls, Inc.9955 International Blvd.Cincinnati, Ohio PHONE (513) 247-5465FAX (513) 247-5462********************SAMPLE PART #Carbon Steel End Connection Valve SeriesSeat Material Valve Size TRIAC Actuator Series Actuator Size On-Off Voltage Options 83C-TX-050/WEA1-XXSee valve part numbermatrix for complete part number and options.Other options available - call for detailsActuators are sized based on clean/clear fluid.NOTE: Heater and thermostat standard (2) auxiliary switches standard SAMPLE PART #Carbon SteelEnd ConnectionValve SeriesSeat MaterialValve SizeTRIAC Actuator SeriesActuator SizeOn-Off VoltageOptions83C-TX-050/WEA1-XXSee valve part number matrix for complete partnumber and options.Other options available - call for detailsActuators are sized based on clean/clear fluid.NOTE: Heater and thermostat standard(2) auxiliary switches standard83C-TH-0200-XXX-X-_ _SAMPLE PART #(2) Valve Series(4) End Connection(6) Seat, Lining & TrimMaterial (5) Valve Size(7) Special Designation(8) Additional Specials(9,10,11) OptionsMANUAL VALVE(3) Body/Ball/StemMaterialHOW TO ORDER:Manual Valves w/ OptionsHOW TO ORDER:Automated Valves(10) Special DesignationSAMPLE PART #(2) Valve Series(3) Body/Ball/StemMaterial(6) Valve Size(5) Seat, Lining, & TrimMaterial(4) End Connection (7) TRIAC Actuator Series(7) Actuator Size (7) Double Acting(8) Accessory (9) Accessory 83C-TX-100/2R3D-XX-_TFM™ is a trademark of Dyneon™, a 3M Company.83-2R-20220525Copyright 2013 A-T Controls, Inc.Cincinnati, Ohio FAX (513) 247-5462********************。

BL V Series Ball ValvesPR OD U CT FEATU R E S AN D B E N E FITS• All stainless steel construction: forged body and ball• FDA approved materials including reinforced PTFE seats• Cavity filled to minimize residue build-up around ball and seat• Full port opening for unrestricted flow in the open position• High temperature and pressure ratings for demanding service applications• Maintenance-free pneumatic actuator with “Normally Closed”, “Normally Open” or “Double Acting” orientations• S tandard ISO pattern mounting pad for easy retrofit from manual handle to pneumatic actuator• Three piece design with floating seals• Lockable manual handle option for added security• Available with the identical control unit options offered on other valve types to give common look, controls interface, and spare parts across a multi-valve systemPR OD U CT S PE CI FI CATI ON S:Materials:Ball:• 1.4404 (DIN EN 10088) / AISI 316LBody:• 1.4408/1.4404 (DIN EN 10088) / AISI 316Seat:• PTFE Cavity FilledInternal Surface Finish:• ≤0.8µ (≤ 32 Ra)Sizes:• DN 15 - 100• Inch 0.50" - 4.00"PE R F OR MAN CE RATI N G S:Maximum Line Pressure:• 10 bar (145 psi)Temperature Ratings:• 0 - 140°C (0-284ºF)• Short-term steam: 160°C (320ºF)Food and Drinks Soups & Sauces Personal CareExtractsChemicalPaintsUtilitiesSteamAD D ITI ONAL OPTI ON SProximity Switch Only• Available with manual handle and pneumatic actuators • 24VDC or 120VAC prox sensors with LED• F eedback for valve open/valve closed position detectionCONTR OL U N ITS FEATURES AND BENEFITS• Automated control and position monitoring for reliable processing • Helps reduce external solenoid valve cabinets • R eliable and long service life - robust clamp connection, water tight seals and reinforced stainless steel air coupling threads to avoid air leakages• Clarity - clear and bright indication of valve position - 5 diodes in LED panel and convenient location• Standardisation - same control unit used on various SPX FLOW valve lines, offers common look and control interface • IP67 (NEMA 6) wash-down ratingCU4 & CU4plus SeriesCONNECTOR OPTIONS • S/O Cord Grip for hard wire (standard)INTERFACE OPTIONS• 24 V DC Direct Connect • AS-i Field Bus Card POSITION INDICATION OPTIONS • 2 internal feedback sensors for valve open/valve closed position detection SOLENOID VALVES • 24 V DC •120 V ACBLV1 - H - DN15-100; 0.50" - 4.00"Ball valve, manually operated, without feedbackPR OD U CT D I M E N S I ONS:BLV1 - HL - DN15-100; 0.50" - 4"Ball valve, manually operated, with feedbackD N15 - 50; 0.50” - 2.00”D N65 - 100; 2.50” - 4.00”SPX FLOW, Inc. reserves the right to incorporate our latest design and material changes without notice or obligation.Design features, materials of construction and dimensional data, as described in this bulletin, are provided for your information only and should not be relied upon unless confirmed in writing. Please contact your local sales representative for product availability in your region. For more information visit .The green “” and “” are trademarks of SPX FLOW, Inc.APV_Valve-Ball-BL V1_DST_GB Version: 05/2020Identification Number: APV-8049 COPYRIGHT © 2020 SPX FLOW, Inc.Based in Charlotte, North Carolina, SPX FLOW, Inc. (NYSE: FLOW) is a multi-industry manufacturing leader. For more information, please visit BLV1 - NC/FZ - DN15-100; .50"-4.00"Ball valve, actuated, with turning actuator / control unitMaximum Tightening Torque and Actuator SizesAD D ITI ONAL TE CH N ICAL DATA:AM E R I CAS S PX FLOW611 Sugar Creek Road Delavan, WI 53115USA+1 262 728 1900APAC S PX FLOW7F, No. 1568, Huashan Road Shanghai, 200052China+86 21 2208 5888E M EA S PX FLOWGottlieb-Daimler-Straße 13 D-59439 Holzwickede Germany+49 2301-9186-0Global locationsPR OD U CT D I M E N S I ON S (CONTI N U E D):。

n g e s e x c e p t e d . R e v i s i o n : 07/2020-005seat sealing:• PTFE-fibre glass reinforced: -10°C up to +n g e s e x c e p t e d . R e v i s i o n : 07/2020-005Carbon steel ball valves of the series KFA16 are provided with a modified coating (modified epoxy / poliamid primer RAL 5012 color blue with a film thickness of at least 0.030 mm). For outdoor applications a proper intermediate and finishing coat shall be applied within 90 days.For details about the order code see "Order information". An overview of the complete material code you can find at the beginning of each product section of the product catalogue.options:• OF: free of oil and grease • ZG: certificate 3.1• SV: spindle extension • SP: gland extension • HZ: heating jacket • FS: fire-safe design• TD: minimal clearance volume by means of half shells (• TS: minimal clearance volume• AE: external parts made o f stainless steel • EB: relief well • HG: hand gear • FW: free spindle • EX: ATEX-certificate • LD: lock deviceFor electric actuated valves only:• AP: accumulator security pack • PT: potentiometer • PO: positioning system For pneumatic actuated valves only:• SD: sound absorber • AD: exhaust air regulator • PV: pilot valve For details see data sheet"GMV3197", "GMV3163" (3/2 way) and "MVA01" (5/2 way). Other types on request.• PS: positioning indicatorFor details see data sheet "MCM2" (mechanical), "MCN2" (inductive, with ATEX 94/9/EC) and "MCS2"(inductive). Other types on request.Pressure temperature diagramThe pressure temperature diagram shows the max. permitted working pressure in relation to the media temperature.The pressure temperature diagram refers to the ball valve of this type. For the actuated units the actuator limits the permissible pressure range to the operating pressure as indicated above, as long as this is lower than the pressure range of the ball valve.If your application has strong temperature variations, you may need additional options like a relief well, to meet the figures.Please tell us your temperature variations with your order.diagram for PTFE sealingdiagram for PTFE fibre-glass reinforcedn g e s e x c e p t e d . R e v i s i o n : 07/2020-005*CV value: The nominal flow rate CVs acc. to VDI/VDE 2173 shows the water quantity in cubic meter per hour with the valve fully opened, ∆p=1 and the water temperature between 5°C and 30°C.**Breakaway torque: all data were determined with 16 bar water at normal ambient temperature. Multiplicator for frictional media is 1.3. If your configuration has special sealing material or your application has critical media consultation is obligatory.Order information:1: automation:• no specification: manually operated • D: pneumatic double acting • S: pneumatic single acting • E: electric actuated 2: type: KFA163: connection size: • 51 63 (DIN, see table)• 81-93 (ANSI, on request)4: materials:• 1. digit: body materialJ = steel O = stainless steel• 2. digit: sealing for spindle• 3. digit: ball materialO = stainless steel• 4. digit: seat sealingT = PTFE (standard) U = PTFE metal coreG = PTFE fibre-glass reinforced5: actuator:• no specification: steel hand lever • automated: see column "actuator"6: options (see "options")Please ask for field specifications that are not listed in thisdata sheet.Before installation please consider the installation and main-[X] KFA16 - [XX] [X]ROT - [X] - [XX] 1 2 3 4 5 6n g e s e x c e p t e d . R e v i s i o n : 07/2020-005Attention!To avoid corrosion inside the spring chamber for single acting actuators caused by aggressive ambient air we recommend pilot valves with integrated air recirculation.High quality pneumatic actuator made of alloy with air connection according to NAMUR and positioning indicator. The actuator works with the rack/bevel method. For further details see the technical data sheet "DR/SC".Types double acting (the actuator opens and closes with compressed air) and single acting (the actuator opens with com-pressed air and closes with spring pressure).The actuators are configured for use with fluid, gas and antifriction medium. For critical media it is strictly recom-mended to inform us!DKFA16 / SKFA16• medium temperature: -20°C up to +120°C(at max. ambient temperature 40°C)Description:• working pressure: 0 - 16 bar • pilot pressure: 6 - 8 barn g e s e x c e p t e d . R e v i s i o n : 07/2020-005High-quality electric actuator in compact design with a body made of high-strength plastics. It has a high-performance motor and a gear drive made of metal. A central control room heater and an electronic torque limiter are equipped as standard. For further details see the technical data sheet "J".Description:• working pressure: 0 - 16 bar•deviating medium temperature -20°C up to +100°C (at max. ambient temperature of 40°C)actuator of type J... (up to DN125).connection voltage type:• 19: 24V AC/DC up to 240V AC/ DC • other voltages on requestn g e s e x c e p t e d . R e v i s i o n : 07/2020-005Ball valves with heating jacket maintain a constant medium temperature inside the valve and therefore allow a defined medium viscosity.The valve is made o f solid steel or stainless steel and is provided with a one-piece shell that is filled with heating medi-um through two connections. For the ball valve all options of the type KFA16 are suitable (see data sheet). On request the ball valve can be automated electrically or pneumatically.The following properties apply for the heating jacket:• heating medium: uncritically fluids• working pressure for heating jacket: max. 25 bar • heating medium temperature: max. 60°COptionally other heating jacket connections are possible as well as higher heating medium pressure and designs for hot。