下载文档原格式
University beam (UB)----通用梁(工字梁)University columns (UC)----通用柱Rolled steel angles (RSA)----角钢RSC----C型钢(槽钢)Rectangular hollow sections (RHS)----矩形中空型钢Square hollow sections (SHS)-----正方形中空型钢Circular hollow sections (CHS)----圆形中空型钢High strength friction GRIP (HSFG)----高强度摩擦紧固螺栓Tension control (TC)----拉力控制All flux -----合金焊剂All-weld-metal test specimen------全焊缝金属试件(完全由焊缝金属组成的缩短断面试件)Automatic welding-----自动焊接Back gouging-----清根Backing----衬垫base metal----母材Bevel angle----破口面角度Box tubing-----箱型管Butt joint ---- 对接接头Butt weld ---- 对接焊缝Cap pass ---- 盖面焊道Complete penetration ---- 完全熔透Corner joint ---- 角接接头contract documents ---- 合同文件contractor ---- 承包商contractor’s Inspector ---- 承包商检验员ESW (electroslag welding) ---- 电渣焊FCA W(flux cored arc welding) ---- 药芯焊丝电弧焊。
钢结构焊接英语术语大全以下是一些常见的钢结构焊接英语术语：1. Welding:焊接2. Weld:焊缝3. Joint:焊接接头4. Fillet weld:角焊缝5. Butt weld:对接焊缝6. Fillet size:角焊缝尺寸7. Throat thickness:鞍部厚度8. Penetration:焊透9. Welding position:焊接位置10. Welding procedure:焊接工艺11. Welding current:焊接电流12. Welding voltage:焊接电压13. Welding speed:焊接速度14. Shielding gas:保护气体15. Preheating:预热16. Post-weld heat treatment:焊后热处理17. Groove:槽口18. Bevel:坡口19. Backing strip:补强条20. Welding helmet:焊接面罩21. Welding electrode:焊接电极22. Welding rod:焊条23. Welding wire:焊丝24. Welding machine:焊接机器25. Welding procedure specification (WPS):焊接工艺规范26. Welding inspector:焊接检验员27. Defect:缺陷28. Porosity:孔隙29. Inclusion:夹杂物30. Undercut:侵彻31. Cracking:裂纹32. Slag:焊渣33. Welding consumables:焊接材料34. Arc length:电弧长度35. Arc voltage:电弧电压36. Arc blow:电弧偏转37. Weld quality:焊接质量38. Non-destructive testing (NDT):无损检测39. Visual inspection:目视检验40. Ultrasonic testing (UT):超声波检测41. Radiographic testing (RT):射线检测42. Magnetic particle testing (MT):磁粉检测43. Liquid penetrant testing (PT):渗透检测44. Welder qualification:焊工资格证书45. Welding symbol:焊接符号46. Tack welds:点焊缝47. Crater:焊缝尾部凹坑48. Back gouging:反刮槽49. Weld toe:焊接母材交线处50. Arc welding:弧焊希望对你有所帮助！。
钢结构专业术语
1. 剪力墙(Shear Wall)
剪力墙是一种承受水平荷载(如风荷载和地震荷载)的结构系统,通常由钢筋混凝土或结构钢构成,在建筑物中起到抵抗侧向力的作用。
2. 抗弯构件(Bending Member)
抗弯构件是指在构件受力过程中主要承受弯矩的构件,如梁、板等。
3. 抗压构件(Compression Member)
抗压构件是指在构件受力过程中主要承受轴向压力的构件,如柱、支撑等。
4. 刚接(Rigid Connection)
刚接是指连接构件时,能够传递弯矩和剪力的连接方式,使连接处的变形很小。
5. 铰接(Hinged Connection)
铰接是指连接构件时,只能传递轴向力,不能传递弯矩的连接方式。
6. 支座(Bearing)
支座是钢结构与基础之间的连接部件,用于传递荷载并允许一定程度的位移。
7. 稳定性(Stability)
稳定性是指结构在各种荷载作用下保持平衡状态的能力,避免发生整
体或局部失稳。
8. 疲劳(Fatigue)
疲劳是指由于反复循环载荷作用导致的材料性能逐渐降低的现象。
9. 腐蚀(Corrosion)
腐蚀是指金属材料在环境作用下发生化学或电化学反应,导致材料失效的过程。
10. 防火(Fire Protection)
防火是指采取一系列措施,以降低火灾发生的风险,并限制火灾蔓延,保护人员和财产安全。
钢结构术语和符号（中英文对照）一、术语1、强度：构件截面材料或连接抵抗破坏的能力。
强度计算是防止结构构件或连接因材料强度被超过而破坏的计算。
2、承载能力：结构或构件不会因强度、稳定或疲劳等因素破坏所能承受的最大内力；或塑性分析形成破坏机构时的最大内力；或达到不适应于继续承载的变形时的内力。
3、脆断：一般指钢结构在拉应力状态下没有出现警示性的塑性变形而突然发生的脆性断裂。
4、强度标准值：国家标准规定的钢材屈服点(屈服强度)或抗拉强度。
5、强度设计值：钢材或连接的强度标准值除以相应抗力分项系数后的数值。
6、一阶弹性分析：不考虑结构二阶变形对内力产生的影响，根据未变形的结构建立平衡条件，按弹性阶段分析结构内力及位移。
7、二阶弹性分析：考虑结构二阶变形对内力产生的影响，根据位移后的结构建立平衡条件，按弹性阶段分析结构内力及位移。
8、屈曲：杆件或板件在轴心压力、弯矩、剪力单独或共同作用下突然发生与原受力状态不符的较大变形而失去稳定。
9、腹板屈曲后强度：腹板屈曲后尚能继续保持承受荷载的能力。
10、通用高厚比：参数，其值等于钢材受弯、受剪或受压屈服强度除以相应的腹板抗弯、抗剪或局部承压弹性屈曲应力之商的平方根。
11、整体稳定：在外荷载作用下，对整个结构或构件能否发生屈曲或失稳的评估。
12、有效宽度：在进行截面强度和稳定性计算时宽度。
假定板件有效的那13、有效宽度系数：板件有效宽度与板件实际宽度的比值。
14、计算长度：构件在其有效约束点间的几何长度乘以考虑杆端变形情况和所受荷载情况的系数而得的等效长度，用以计算构件的长细比。
计算焊缝连接强度时采用的焊缝长度。
15、长细比：构件计算长度与构件截面回转半径的比值。
16、换算长细比：在轴心受压构件的整体稳定计算中，按临界力相等的原则，将格构式构件换算为实腹构件进行计算时所对应的长细比或将弯扭与扭转失稳换算为弯曲失稳时采用的长细比。
17、支撑力：为减小受压构件(或构件的受压翼缘)的自由长度所设置的侧向支承处，在被支撑构件（或构件受压翼缘)的屈曲方向，所需施加于该构件(或构件受压冀缘)截面剪心的侧向力。
最全的钢结构术语（中英对照)Aacceptable quality 合格质量acceptance lot 验收批量aciera 钢材admixture 外加剂against slip coefficient between friction surface of high-strength bolted connection 高强度螺栓摩擦面抗滑移系数aggregate 骨料air content 含气量air-dried timber 气干材allowable ratio of height to sectional thickness of masonry wall or column砌体墙、柱容许高厚比allowable slenderness ratio of steel member 钢构件容许长细比allowable slenderness ratio of timber compression member 受压木构件容许长细比allowable stress range of fatigue 疲劳容许应力幅allowable ultimate tensile strain of reinforcement 钢筋拉应变限值allowable value of crack width 裂缝宽度容许值allowable value of deflection of structural member 构件挠度容许值allowable value of deflection of timber bending member 受弯木构件挠度容许值allowable value of deformation of steel member 钢构件变形容许值allowable value of deformation of structural member 构件变形容许值allowable value of drift angle of earthquake resistant structure 抗震结构层间位移角限值amplified coefficient of eccentricity 偏心距增大系数anchorage 锚具anchorage length of steel bar 钢筋锚固长度approval analysis during construction stage 施工阶段验算arch 拱arch with tie rod 拉捍拱arch-shaped roof truss 拱形屋架area of shear plane 剪面面积area of transformed section 换算截面面积aseismic design 建筑抗震设计assembled monolithic concrete structure 装配整体式混凝土结构automatic welding 自动焊接auxiliary steel bar 架立钢筋Bbackfilling plate 垫板balanced depth of compression zone 界限受压区高度balanced eccentricity 界限偏心距bar splice 钢筋接头bark pocket 夹皮batten plate 缀板beam 次梁bearing plane of notch 齿承压面bearing plate 支承板bearing stiffener 支承加劲肋bent—up steel bar 弯起钢筋block 砌块block masonry 砌块砌体block masonry structure 砌块砌体结构blow hole 气孔board 板材bolt 螺栓bolted connection (钢结构螺栓连接bolted joint (木结构螺栓连接bolted steel structure 螺栓连接钢结构bonded prestressed concrete structure 有粘结预应力混凝土结构bow 顺弯brake member 制动构件breadth of wall between windows 窗间墙宽度brick masonry 砖砌体brick masonry column 砖砌体柱brick masonry structure 砖砌体结构brick masonry wall 砖砌体墙broad—leaved wood 阔叶树材building structural materials 建筑结构材料building structural unit 建筑结构单元building structure 建筑结构built-up steel column 格构式钢柱bundled tube structure 成束筒结构burn-through 烧穿butt connection 对接butt joint 对接butt weld 对接焊缝Ccalculating area of compression member 受压构件计算面积calculating overturning point 计算倾覆点calculation of load—carrying capacity of member 构件承载能力计算camber of structural member 结构构件起拱cantilever beam 挑梁cap of reinforced concrete column 钢筋混凝土柱帽carbonation of concrete 混凝土碳化cast-in—situ concrete slab column structure 现浇板柱结构cast-in—situ concrete structure 现浇混凝土结构cavitation 孔洞cavity wall 空斗墙cement 水泥cement content 水泥含量cement mortar 水泥砂浆characteriseic value of live load on floor or roof 楼面、屋面活荷载标准值characteristi cvalue o fwindload 风荷载标准值characteristic value of concrete compressive strength 混凝土轴心抗压强度标准值characteristic value of concrete tensile strength 混凝土轴心抗拉标准值characteristic value of cubic concrete compressive strength混凝土立方体抗压强度标准值characteristic value of earthquake action 地震作用标准值characteristic value of horizontal crane load 吊车水平荷载标准值characteristic value of masonry strength 砌体强度标准值characteristic value of permanent action 永久作用标准值characteristic value of snowload 雪荷载标准值characteristic value of strength of steel 钢材强度标准值characteristic value of strength of steel bar 钢筋强度标准值characteristic value of uniformly distributed live load 均布活标载标准值characteristic value of variable action 可变作用标准值characteristic value of vertical crane load 吊车竖向荷载标准值charaeteristic value of material strength 材料强度标准值checking section of log structural member，原木构件计算截面chimney 烟囱circular double-layer suspended cable 圆形双层悬索circular single—layer suspended cable 圆形单层悬索circumferential weld 环形焊缝classfication for earthquake-resistance of buildings 建筑结构抗震设防类别clear height 净高clincher 扒钉coefficient of equivalent bending moment of eccentrically loaded steel memher （beam—column 钢压弯构件等效弯矩系数cold bend inspection of steelbar 冷弯试验cold drawn bar 冷拉钢筋cold drawn wire 冷拉钢丝cold-formed thin-walled sectionsteel 冷弯薄壁型钢cold—formed thin-walled steel structure 冷弯薄壁型钢结构cold—rolled deformed bar 冷轧带肋钢筋column bracing 柱间支撑combination value of live load on floor or roof 楼面、屋面活荷载组合值compaction 密实度compliance control 合格控制composite brick masonry member 组合砖砌体构件composite floor system 组合楼盖composite floor with profiled steel sheet 压型钢板楼板composite mortar 混合砂浆composite roof truss 组合屋架compostle member 组合构件compound stirrup 复合箍筋compression member with large eccentricity 大偏心受压构件compression member with small eccentricity 小偏心受压构件compressive strength at an angle with slope of grain 斜纹承压强度compressive strength perpendicular to grain 横纹承压强度concentration of plastic deformation 塑性变形集中conceptual earthquake—resistant design 建筑抗震概念设计concrete 混凝土concrete column 混凝土柱concrete consistence 混凝土稠度concrete floded-plate structure 混凝土折板结构concrete foundation 混凝土基础concrete mix ratio 混凝土配合比concrete wall 混凝土墙concrete-filled steel tubular member 钢管混凝土构件conifer 针叶树材coniferous wood 针叶树材connecting plate 连接板connection 连接connections of steel structure 钢结构连接connections of timber structure 木结构连接consistency of mortar 砂浆稠度constant cross—section column 等截面柱construction and examination concentrated load 施工和检修集中荷载continuous weld 连续焊缝core area of section 截面核芯面积core tube supported structure 核心筒悬挂结构corrosion of steel bar 钢筋锈蚀coupled wall 连肢墙coupler 连接器coupling wall-beam 连梁coupling wall—column.。
钢结构设计专用术语1．1结构术语1 焊接钢结构welded steel structure以手工电弧焊接或自动、半自动埋弧焊接作为连接手段并用金属焊条、焊丝作为连接材料，将钢结构和部件连接成整体的结构。
2 铆接钢结构riveted steel structure以铆钉作为连接件将钢结构或部件连接成整体的结构。
3 螺栓连接钢结构bolted steel structure以普通螺栓作为连接件将钢结构或部件连接成整体的结构。
4 高强螺栓连接钢结构high-strength boltec steel structure以高强螺栓作为连接件将钢结构件或部件连接成整体的结构。
5 冷弯薄壁型钢结构cold-formed thin-walled steel structure以冷弯薄壁型钢作为主要材料所制成的结构。
6 钢管结构steel tubular structure以圆钢管或方钢管或矩形钢管作为主要材料制成的结构7 预应力钢结构prestressed steel structure通过张拉高强度钢丝束或钢绞线等手段或调整支座等方法，再钢结构构件或结构体系内建立预加应力的结构。
1.2 构件、部件术语1 实腹式钢柱solid-web steel column腹板为整体的竖向受压钢构件2格构式钢柱built-up steel column;laced or battened compression member由钢缀才将各分肢组成整体的竖向受压钢构件。
分双肢，三肢和四肢格构式钢柱3分离式钢柱separated steel column支承屋盖的竖向刚肢体和支承吊车梁的竖向刚肢体两者用水平钢板连接而成整体的双肢受压钢构件。
4 缀才(缀件) lacing and batten elements在格构式受压钢构件中用以连接肢体并承受剪力的腹杆。
分缀条和缀板4.1缀条lacing bar在格构式受压钢构件中用以连接肢体并承受剪力的条状腹杆缀板batten plate5 钢柱分肢steel column compnent组成格构式钢柱或分离式钢柱的竖向肢体6钢柱脚steel column base扩大钢柱底端与基础相连接的加强部分。
钢构件中英文对照表序号代号(中文）中文代号（英文）英文1 钢构构件表STEEL MEMBER SCHEDULE steel member schedule2 钢架STEEL FRAME steel frame3 墙WALL wall4 屋面ROOF roof5 柱COLUMN column6 梁BEAM beam7 支撑BRACING bracing8 窗WINDOW window9 门DOOR10 包边EDGE COVER edge cover11 水槽WATER GUTTER water gutter12 落水管WATER PIPE water pipe13 漏斗FILTER filter14 夹层(阁楼）MEZZANINE FLOOR mezzanine floor15 YP 雨棚CANOPY canopy16 GZ 钢柱SC/ PC STEEL COLUMN/COLUMN steel column/17 GJ 桁架TR TRUSS truss18 GL 椽梁RB RAFTER BEAM rafter beam19 GL 屋面梁PB ROOF BEAM roof beam20 GL 边梁EB EDGE ROOF BEAM edge roof beam21 XL 系梁ST ROOF STRUT roof strut22 CG 墙面撑杆WS WALL STIFFENER wall stiffener23 DCL 吊车梁CRB CRANE RAIL BEAM crane rail beam24 MZ 门柱DC DOOR COLUMN door column25 ML 门梁DH DOOR HEAD BEAM door head beam26 SC 水平支撑BR ROOR BRACING roor bracing27 ZC 柱撑WBR WALL BRACING wall bracing28 ZL 主梁MB MEZZANINE FLOOR BEAM mezzanine floor beam29 CL 次梁MB MEZZANINE FLOOR BEAM mezzanine floor beam30 楼面托架FJ FLOOR JOIST floor joist31 YM 预埋件EMBEDMENT embedment32 KFZ 抗风柱 WIND RESISTANCE COLUMN wind resistance column33 女儿墙PARAPET parapet34 女儿墙柱 PARAPET COLUMN parapet column35 LG 拉杆TIE ROD tie rod36 屋面撑杆Bar ROOF STAY BAR37 立面图ELEVATION38 平面图PLAN39 施工图SHOP DRAWING40 屋面布置图ROOF MARKING PLAN41 节点大样DETAIL42 节点板JOINT PLATE钢结构专业英语（一）A &BAacceptable quality 合格质量；acceptance lot 验收批量；admixture 外加剂against slip coefficient between friction surface of high-strength bolted connection 高强度螺栓摩擦面抗滑移系数aggregate 骨料；air content 含气量air-dried timber 气干材allowable ratio of height to sectional thickness of masonry wall or column 砌体墙、柱容许高厚比allowable slenderness ratio of steel member 钢构件容许长细比allowable slenderness ratio of timber compression member 受压木构件容许长细比allowable stress range of fatigue 疲劳容许应力幅allowable ultimate tensile strain of reinforcement 钢筋拉应变限值allowable value of crack width 裂缝宽度容许值allowable value of deflection of structural member 构件挠度容许值allowable value of deflection of timber bending member 受弯木构件挠度容许值allowable value of deformation of steel member 钢构件变形容许值allowable value of deformation of structural member 构件变形容许值allowable value of drift angle of earthquake resistant structure 抗震结构层间位移角限值amplified coefficient of eccentricity 偏心距增大系数anchorage 锚具；anchorage length of steel bar 钢筋锚固长度approval analysis during construction stage 施工阶段验算arch 拱；arch with tie rod 拉捍拱arch—shaped roof truss 拱形屋架；area of shear plane 剪面面积area of transformed section 换算截面面积；aseismic design 建筑抗震设计assembled monolithic concrete structure 装配整体式混凝土结构automatic welding 自动焊接auxiliary steel bar 架立钢筋Bbackfilling plate 垫板；balanced depth of compression zone 界限受压区高度balanced eccentricity ；界限偏心距；bar splice 钢筋接头bark pocket 夹皮；batten plate 缀板；beam 次梁bearing plane of notch 齿承压面；bearing plate 支承板bearing stiffener 支承加劲肋；bent-up steel bar 弯起钢筋；block 砌块block masonry 砌块砌体；block masonry structure 砌块砌体结构blow hole 气孔；board 板材；bolt 螺栓bolted connection (钢结构)螺栓连接；bolted joint (木结构)螺栓连接；bolted steel structure 螺栓连接钢结构；bonded prestressed concrete structure 有粘结预应力混凝土结构bow 顺弯；brake member 制动构件breadth of wall between windows 窗间墙宽度；brick masonry 砖砌体brick masonry column 砖砌体柱；brick masonry structure 砖砌体结构brick masonry wall 砖砌体墙；broad—leaved wood 阔叶树材building structural materials 建筑结构材料；building structural unit 建筑结构单元building structure 建筑结构；built—up steel column 格构式钢柱bundled tube structure 成束筒结构burn—through 烧穿；butt connection 对接butt joint 对接；butt weld 对接焊缝。
常用字母代号B：板WJ：屋架WB：屋面板TJ：托架KB：空心板CJ：天窗架CB：槽形板KJ：框架ZB：折板GJ：钢架MB：密肋板ZJ：支架TB：楼梯板Z：柱GB：盖板或沟盖板J：基础YB：挡雨板或檐口板SJ：设备基础DB：吊车安全走道板ZH：桩QB：墙板ZC：柱间支撑TGB：天沟板CC：垂直支撑L：梁SC：水平支撑WL：屋面梁T：梯DL：吊车梁YP：雨蓬QL：圈梁YT：阳台GL：过梁LD：梁垫LL：连系梁M：预埋件JL：基础梁TD：天窗端壁TL：楼梯梁W：钢筋网LT：檩条G：钢筋骨架L：角钢GLT：刚性檩条GZ：钢柱WLT：屋脊檩条QT：球墨铸铁SC：水平支撑SC：铸钢ZC：柱间支撑SCS：不锈钢铸件GJ：刚架GJZ：刚架柱GXG：刚性系杆GJL：刚架梁YXB：压型金属板TL：托梁SQZ：山墙柱LT：檩条XT：斜拉条QL：墙梁MZ：门边柱YC：隅撑ML：门上梁T：拉条CG：撑杆HJ：桁架FHB：复合板XG：系杆LG：拉管QCG：墙撑管QLG：墙拉管GXL：斜拉条GZL：直拉条YG：压杆或是圆管（从材料表中分别）GJ30-1：跨度为30m的门式刚架，编号为1号项目编码项目名称单位所包含计算构件010417001螺栓t螺栓与螺母、垫片重量合计010601001钢屋架t(樘)钢架结构指的是整个钢架（柱、梁组合）、排架结构指钢屋架、钢屋架相接型钢类配件010601002钢网架t（樘）钢丝网片及配件010602001钢托架t托架及配件010602002钢桁架t桁架各杆件及相接型钢配件010603001实腹柱t单柱及相接型钢类配件010603002空腹柱t同上010603003钢管柱t同上010604001钢梁t同上010604002钢吊车梁t吊车梁、连接板及相接型钢类配件010605001压型钢板楼板m2屋面板010605002压型钢板墙板m2图示面积，不包括包边010606001钢支撑t支撑ZC、斜撑SC、隅撑YC010606002钢檩条t檩条LT、墙檩条QL、拉条L010606003钢天窗架t天窗架及型钢类配件010606004钢挡风架t挡风架及型钢类配件010606005钢墙架t010606006钢平台t010606007钢走道t钢走道板、栏杆扶手、支架及其它型钢类配件010606008钢梯t踏步板、底梁、平台板、护笼等其它型钢类配件010606009钢栏杆t栏杆及型钢类构件010606010钢漏斗t010606011钢支架t010606012零星钢构件t其它小型分离式型钢构件。
最全的钢结构术语和符号（二）二、符号1、作用和作用效应设计值F——集中荷载；H——水平力；M——弯矩；N——轴心力；P——高强度螺栓的预拉力；Q——重力荷载；R——支座反力；V——剪力。
2、计算指标E ——钢材的弹性模量；Ec——混凝土的弹性模量；G ——钢材的剪变模量；Nat——个锚栓的抗拉承载力设计值；Nbt、Nbv、Nbc——一个螺栓的抗拉、抗剪和承压承载力设计值；Nrt、Nrv、Nrc——一个铆钉的抗拉、抗剪和承压承载力设计值；Ncv——组合结构中一个抗剪连接件的抗剪承载力设计值；NpjtNpjc——受拉和受压支管在管节点处的承载力设计值；Sb——支撑结构的侧移刚度(产生单位侧倾角的水平力)；F ——钢材的抗拉、抗压和抗弯强度设计值；fv——钢材的抗剪强度设计值；fce——钢材的端面承压强度设计值；fst——钢筋的抗拉强度设计值；fy——钢材的屈服强度(或屈服点)；fat——锚栓的抗拉强度设计值；fbtfbvfbc——螺栓的抗拉、抗剪和承压强度设计值；frtfrvfrc——铆钉的抗拉、杭剪和承压强度设计值；fwtfwvfwc——对接焊缝的抗拉，抗剪和抗压强度设计值；fwt——角焊缝的抗拉、抗剪和抗压强度设计值；fc ——混凝土抗压强度设计值；Δu——楼层的层间位移；[υQ]——仅考虑可变荷载标准值产生的挠度的容许值；[υT]——同时考虑永久和可变荷载标准值产生的挠度的容许值；σ——正应力；σc——局部压应力；σf——垂直于角焊缝长度方向，按焊缝有效截面计算的应力；Δσ——疲劳计算的应力幅或折算应力幅；Δσ——变幅疲劳的等效应力幅；[Δσ]——疲劳容许应力幅；Σcrσc.crτcr——板件在弯曲应力、局部压应力和剪应力单独作用时的临界应力；τ——剪应力；τf——沿角焊缝长度方向，按焊缝有效截面计算的剪应力；ρ——质量密度。
3、几何参数A ——毛截面面积；An——净截面面积；H——柱的高度；H1、H2、H3——阶形柱上段、中段(或单阶柱下段)、下段的高度；I ——毛截面惯性矩；It——毛截面抗扭惯性矩；Iw——毛截面扇性惯性矩；In——净截面惯性矩；S ——毛截面面积矩；W ——毛截面模量；Wn——净截面模量；Wp——塑性毛截面模量；Wpn——塑性净截面模量；ag ——间距，间隙；b——板的宽度或板的自由外伸宽度；bo——箱形截面翼缘板在腹板之间的无支承宽度；混凝土板托顶部的宽度；bs——加劲肋的外伸宽度；be——板件的有效宽度；d ——直径；de——有效直径；do——孔径；e ——偏心距；h ——截面全高；楼层高度；hc1——混凝土板的厚度；hc2——混凝土板托的厚度；he——角焊缝的计算厚度；hf——角焊缝的焊脚尺寸；hω——腹板的高度。
强度strength构件截面材料或连接抵抗破坏的能力。
强度计算是防止结构构件或连接因材料强度被超过而破坏的计算。
★承载能力load-carrying capacity结构或构件不会因强度、稳定或疲劳等因素破坏所能承受的最大内力；或塑性分析形成破坏机构时的最大内力；或达到不适应于继续承载的变形时的内力。
★脆断brittle fracture一般指钢结构在拉应力状态下没有出现警示性的塑性变形而突然发生的脆性断裂。
★强度标准值characteristic value of strength国家标准规定的钢材屈服点(屈服强度)或抗拉强度。
★强度设计值design value of strength钢材或连接的强度标准值除以相应抗力分项系数后的数值。
★一阶弹性分析first order elastic analysis不考虑结构二阶变形对内力产生的影响，根据未变形的结构建立平衡条件，按弹性阶段分析结构内力及位移。
★阶弹性分析second order elastic analysis考虑结构二阶变形对内力产生的影响，根据位移后的结构建立平衡条件，按弹性阶段分析结构内力及位移。
★屈曲buckling杆件或板件在轴心压力、弯矩、剪力单独或共同作用下突然发生与原受力状态不符的较大变形而失去稳定。
★腹板屈曲后强度 post-buckling strength of web plate腹板屈曲后尚能继续保持承受荷载的能力。
★通用高厚 normalizde web slenderness参数，其值等于钢材受弯、受剪或受压屈服强度除以相应的腹板抗弯、抗剪或局部承压弹性屈曲应力之商的平方根。
★整体稳定 overall stability在外荷载作用一下，对整个结构或构件能否发生屈曲或失稳的评估。
★有效宽度。
effective width在进行截面强度和稳定性计算时，假定板件有效的那一部分宽度。
★有效宽度系数effective width factor板件有效宽度与板件实际宽度的比值。
★算长度effective length构件在其有效约束点间的几何长度乘以考虑杆端变形情况和所受荷载情况的系数而得的等效长度，用以计算构件的长细比。
计算焊缝连接强度时采用的焊缝长度。
★长细比、slenderness ratio构件计算长度与构件截面回转半径的比值。
★换算长细比 equivalent slenderness ratio在轴心受压构件的整体稳定计算中，按临界力相等的原则，将格构式构件换算为实腹构件进行计算时所对应的长细比或将弯扭与扭转失稳换算为弯曲失稳时采用的长细比。
★支撑力 nodal bracing force为减小受压构件(或构件的受压翼缘)的自由长度所设置的侧向支承处，在被支撑构件〔或构件受压翼缘)的屈曲方向，所需施加上该构件(或构件受压翼缘)截面剪心的侧向力。
★无支撑纯框架 unbraced frame依靠构件及节点连接的抗弯能力，抵抗侧向荷载的框架。
★强支撑框架frame braced with strong bracing system在支撑框架中，支撑结构(支撑析架、剪力墙、电梯井等)抗侧移刚度较大，可将该框架视为无侧移的框架。
★弱支撑框架frame braced with weak bracing system在支撑框架中，支撑结构抗侧移刚度较弱，不能将该框架视为无侧移的框架。
★摇摆柱 leaning column枢架内两端为铰接不能抵抗侧向荷载的柱。
★柱腹板节点域panel zone of column web框架梁柱的刚接节点处，柱腹板在梁高度范围内的区域。
★球形钢支座 spherical steel bearing使结构在支座处可以沿任意方向转动的钢球面作为传力的铰接支座或可移动支座。
★橡胶支座couposite rubber and steel support满足支座位移要求的橡胶和薄钢板等复合材料制品作为传递支座反力的支座。
★主管chord member钢管结构构件中，在节点处连续贯通的管件，如桁架中的弦杆。
★支管 bracing member钢管结构中，在节点处断开并与主管相连的管件，如桁架中与主管相连的腹杆。
★隙节点 gap joint两支管的趾部离开一定距离的管节点。
★搭接节点 overlap joint在钢管节点处，两支管相互搭接的节点。
★平面管节点 uniplanar joint支管与主管在同一平面内相互连接的节点。
★空间管节点 multiplanar joint在不同平面内的支管与主管相接而形成的管节点。
★组合构件 built-up member由一块以上的钢板(或型钢)相互连接组成的构件，如工字形截面或箱形截面组合梁或柱。
★钢与混凝土组合梁 composite steel and concrete beam由混凝土翼板与钢梁通过抗剪连接件组合而成能整体受力的梁。
Aacceptable quality 合格质量acceptance lot 验收批量aciera 钢材admixture 外加剂against slip coefficient between friction surface of high-strength bolted connection 高强度螺栓摩擦面抗滑移系数aggregate 骨料air content 含气量air-dried timber 气干材allowable ratio of height to sectional thickness of masonry wall or column砌体墙、柱容许高厚比allowable slenderness ratio of steel member 钢构件容许长细比allowable slenderness ratio of timber compression member 受压木构件容许长细比allowable stress range of fatigue 疲劳容许应力幅allowable ultimate tensile strain of reinforcement 钢筋拉应变限值allowable value of crack width 裂缝宽度容许值allowable value of deflection of structural member 构件挠度容许值allowable value of deflection of timber bending member 受弯木构件挠度容许值allowable value of deformation of steel member 钢构件变形容许值allowable value of deformation of structural member 构件变形容许值allowable value of drift angle of earthquake resistant structure抗震结构层间位移角限值amplified coefficient of eccentricity 偏心距增大系数anchorage 锚具anchorage length of steel bar 钢筋锚固长度approval analysis during construction stage 施工阶段验算arch 拱arch with tie rod 拉捍拱arch-shaped roof truss 拱形屋架area of shear plane 剪面面积area of transformed section 换算截面面积aseismic design 建筑抗震设计assembled monolithic concrete structure 装配整体式混凝土结构automatic welding 自动焊接auxiliary steel bar 架立钢筋Bbackfilling plate 垫板balanced depth of compression zone 界限受压区高度balanced eccentricity 界限偏心距bar splice 钢筋接头bark pocket 夹皮batten plate 缀板beam 次梁bearing plane of notch 齿承压面bearing plate 支承板bearing stiffener 支承加劲肋bent-up steel bar 弯起钢筋block 砌块block masonry 砌块砌体block masonry structure 砌块砌体结构blow hole 气孔board 板材bolt 螺栓bolted connection (钢结构螺栓连接bolted joint (木结构螺栓连接bolted steel structure 螺栓连接钢结构bonded prestressed concrete structure 有粘结预应力混凝土结构bow 顺弯brake member 制动构件breadth of wall between windows 窗间墙宽度brick masonry 砖砌体brick masonry column 砖砌体柱brick masonry structure 砖砌体结构brick masonry wall 砖砌体墙broad-leaved wood 阔叶树材building structural materials 建筑结构材料building structural unit 建筑结构单元building structure 建筑结构built-up steel column 格构式钢柱bundled tube structure 成束筒结构burn-through 烧穿butt connection 对接butt joint 对接butt weld 对接焊缝Ccalculating area of compression member 受压构件计算面积calculating overturning point 计算倾覆点calculation of load-carrying capacity of member 构件承载能力计算camber of structural member 结构构件起拱cantilever beam 挑梁cap of reinforced concrete column 钢筋混凝土柱帽carbonation of concrete 混凝土碳化cast-in-situ concrete slab column structure 现浇板柱结构cast-in-situ concrete structure 现浇混凝土结构cavitation 孔洞cavity wall 空斗墙cement 水泥cement content 水泥含量cement mortar 水泥砂浆characteriseic value of live load on floor or roof 楼面、屋面活荷载标准值characteristi cvalue o fwindload 风荷载标准值characteristic value of concrete compressive strength 混凝土轴心抗压强度标准值characteristic value of concrete tensile strength 混凝土轴心抗拉标准值characteristic value of cubic concrete compressive strength混凝土立方体抗压强度标准值characteristic value of earthquake action 地震作用标准值characteristic value of horizontal crane load 吊车水平荷载标准值characteristic value of masonry strength 砌体强度标准值characteristic value of permanent action 永久作用标准值characteristic value of snowload 雪荷载标准值characteristic value of strength of steel 钢材强度标准值characteristic value of strength of steel bar 钢筋强度标准值characteristic value of uniformly distributed live load 均布活标载标准值characteristic value of variable action 可变作用标准值characteristic value of vertical crane load 吊车竖向荷载标准值charaeteristic value of material strength 材料强度标准值checking section of log structural member，原木构件计算截面chimney 烟囱circular double-layer suspended cable 圆形双层悬索circular single-layer suspended cable 圆形单层悬索circumferential weld 环形焊缝classfication for earthquake-resistance of buildings 建筑结构抗震设防类别clear height 净高clincher 扒钉coefficient of equivalent bending moment of eccentrically loaded steel memher (beam-column 钢压弯构件等效弯矩系数cold bend inspection of steelbar 冷弯试验cold drawn bar 冷拉钢筋cold drawn wire 冷拉钢丝cold-formed thin-walled sectionsteel 冷弯薄壁型钢cold-formed thin-walled steel structure 冷弯薄壁型钢结构cold-rolled deformed bar 冷轧带肋钢筋column bracing 柱间支撑combination value of live load on floor or roof 楼面、屋面活荷载组合值compaction 密实度compliance control 合格控制composite brick masonry member 组合砖砌体构件composite floor system 组合楼盖composite floor with profiled steel sheet 压型钢板楼板composite mortar 混合砂浆composite roof truss 组合屋架compostle member 组合构件compound stirrup 复合箍筋compression member with large eccentricity 大偏心受压构件compression member with small eccentricity 小偏心受压构件compressive strength at an angle with slope of grain 斜纹承压强度compressive strength perpendicular to grain 横纹承压强度concentration of plastic deformation 塑性变形集中conceptual earthquake-resistant design 建筑抗震概念设计concrete 混凝土concrete column 混凝土柱concrete consistence 混凝土稠度concrete floded-plate structure 混凝土折板结构concrete foundation 混凝土基础concrete mix ratio 混凝土配合比concrete wall 混凝土墙concrete-filled steel tubular member 钢管混凝土构件conifer 针叶树材coniferous wood 针叶树材connecting plate 连接板connection 连接connections of steel structure 钢结构连接connections of timber structure 木结构连接consistency of mortar 砂浆稠度constant cross-section column 等截面柱construction and examination concentrated load 施工和检修集中荷载continuous weld 连续焊缝core area of section 截面核芯面积core tube supported structure 核心筒悬挂结构corrosion of steel bar 钢筋锈蚀coupled wall 连肢墙coupler 连接器coupling wall-beam 连梁coupling wall-column... 墙肢coursing degree of mortar 砂浆分层度cover plate 盖板covered electrode 焊条crack 裂缝crack resistance 抗裂度crack width 裂缝宽度crane girder 吊车梁crane load 吊车荷载creep of concrete 混凝土徐变crook 横弯cross beam 井字梁cup 翘弯curved support 弧形支座cylindrical brick arch 砖筒拱Ddecay 腐朽decay prevention of timber structure 木结构防腐defect in timber 木材缺陷deformation analysis 变形验算degree of gravity vertical for structure or structural member 结构构件垂直度degree of gravity vertical forwall surface 墙面垂直度degree of plainness for structural memer 构件平整度degree of plainness for wall surface 墙面平整度depth of compression zone 受压区高度depth of neutral axis 中和轴高度depth of notch 齿深design of building structures 建筑结构设计design value of earthquake-resistant strength of materials 材料抗震强度设计值design value of load-carrying capacity of members 构件承载能力设计值designations 0f steel 钢材牌号designvalue of material strength 材料强度设计值destructive test 破损试验detailing reintorcement 构造配筋detailing requirements 构造要求diamonding 菱形变形diaphragm 横隔板dimensional errors 尺寸偏差distribution factor of snow pressure 屋面积雪分布系数dogspike 扒钉yield strength (yield point of steel 钢材(钢筋屈服强度(屈服点)Carry out drilling operation in accordance with the drilling program. 按钻井程序进行钻井作业. Prepared bell nipple. 准备”喇叭口”短节.Make up 2 joints of drill pipe. 接两根钻杆.Break out this connection. 卸开该接头.Run hole opener to sea bed. 下扩眼器到海底Mix gel fluid for drilling conductor hole. 为钻导管井眼配制高粘度泥浆.Make up bottom hole assembly. 组合下部钻具Check and reset crown-saver on every tour. 每个班都要检查并重新调整天车防碰装置. Number stands on trip out and trip in. 起下钻时给立柱编号.Pick up BHA and run to seafloor. 将下部钻具下到海底.Pick up stands. 接立柱Don’t drill faster than 15 minutes for 1 stand. 钻进速度别超过15分钟1根立柱Drop TOTCO. 投(陶特)测斜仪Fish TOTCO with overshot. 用打捞筒捞起测斜仪Resume drilling to T.D. 继续钻进到总深Circulate 15 minutes.循环15分钟Run in hole. 下钻Put out of hole. 起钻Make an inventory of all ring gaskets. 开一个所有垫圈的清单Use spinning tong. 使用气动扳手Operate the air winch. 操作气动绞车Lay down 57 joints of 5”drill pipe. 甩57根钻杆Pick up drill stem test tool. 提起钻杆测试工具Circulate mud for 2 hours. 循环泥浆2小时Move string during circulation. 在循环时注意活动钻具Circulate hole clean. 循环清洗井眼Circulate bottoms up. 循环泥浆几周Fill up every 5 stands. 每5柱灌泥浆一次Check mud weight every 15 minutes. 每15分钟检查泥浆比重Reverse out excess cement. 反循环替出多余的泥浆Change/replace old mud by new mud. 用新的泥浆替换出旧的泥浆Stop drilling. 停止钻进Drilling ahead. 钻进Pull out of hole bit. 起出钻头Change bit. 换钻头Run the wear bushing. 下抗磨补心The bit thread type is regular pin. 钻头丝扣是正规公扣What’s the make-up torque? 上扣扭矩要多大?Run in 9”collars. 下9”钻铤The cathead can’t give enough torque. 猫头力量不够Connect crossover sub. 接上配合接头The tong angle is too small. 大钳的角度太小了Stop circulating. 停止循环泥浆Break out the stand. 卸立柱Set the single into the mousehole. 把这个单根放进鼠洞Can we break out the pipe with rotary table? 可用转盘卸扣吗? No! Break it out with tong. 不行! 要用大钳卸扣Spin it out with the air spanner. 用气动扳手卸扣Put the pipe wiper on the string. 装上钻杆刮泥器Don’t set this stand back. 这根钻杆不要放在钻杆盒上Make up the lift sub. 接好提升短节Secure the safety clamp. 上紧安全卡瓦The bit is nearing the shoe. 钻头快到套管鞋了Slow down the running speed. 放慢下放速度This is the undergauged interval. 这是缩径井段This is the drilling program. 这是钻井设计书How much weight on bit is required? 要加多少钻压?Keep the rotary speed at 120---140 RPM. 转速保持120---140转/分Keep the flow rate at 3000 LPM. 保持排量3000升/分The pump pressure is too high. 泵压太高了Don’t ream the hole too fast. 划眼不要太快Notice the rotary torque. 注意转盘扭矩的变化The penetration rate is getting slower. 钻速变慢了The bit is nearly worn out. 钻头快磨光了Stop drilling at 2000 meters. 钻至2000米停钻Circulate for one hour. 循环一个小时The pump pressure has increased. 泵压升高了One nozzle may be plugged. 可能有一个水眼(或: 喷嘴)堵了What is the hook load? 悬重多少?What’s the pick-up weight? 上提重量是多少?What’s the lowering weight? 下放重量是多少?Run in HWDP. 下加重钻杆A stabilizer is needed here. 这里需要一个扶正器This is a flexible sub. 这是挠性接头This is the BHA log. 这是下部钻具组合记录Record all outside and inside diameters. 记录好所有(入井工具的)内外径We need a short drill collar. 需要一根短钻铤Pull the cat line. 拉猫头Operate the break lever. 操作(或:扶)刹把Stop the pumps. 停泵Make a wiper trip. 通井Retrieve wear bushing. 取出抗磨补心Bleed off pressure. (释)放压(力)Keep 5 wraps on the drum. 滚筒上留5圈Set slips. 座上卡瓦If tight hole, repeat wiper trip. 如果井眼紧, 重复划眼Setback bottom hole assembly. 将下部钻具立于钻杆盒内Make sure all alarms are on. 确保所有的警报信号都开着Lay down TDS spinner. 拆下顶部驱动的旋扣器Run in hole bit #15 to bottom. 用15号钻头下钻到井底Run in hole to casing shoe. 下钻至套管鞋Pick up same bit and BHA. 装上同样的钻头和钻具组合Lay down 5”HW drill pipe. 甩5”加重钻杆Move string every 2 hours. 每2小时活动钻具一次Keep area around shaker clean. 保持振动筛区域干净Control trip gas. 控制起下钻气Ream if needed. 如必要时进行划眼Select the best penetration rate. 选择最佳钻进速度Fix the traveling assembly. 固定游动系统100. Check power tongs and spinning rope are on drill floor. 检查动力钳和尾绳是否在钻台What’s the weight on bit? 钻压是多少?What is the BHA of this well? 这口井的下部钻具如何组合?Drill out cement. 钻穿水泥Latch the elevator. 扣吊卡Unlatch the elevator. 开吊卡Set the slips. 放卡瓦Adjust the crown-o-matic (crown saver). 调整防碰天车Lock the hook pin. 锁紧大钩销子Check OD of stabilizer. 检查扶正器的外径Perform leak off test. 进行地层破裂(或:渗漏)测试Connect kill and choke line. 接上压井和放喷管线Reverse out the drill pipe. 反循环清洗钻杆Make a short trip. 进行短途起下钻Change the cutters. 换割刀Slug the pipe. 灌重泥浆Drill the stand down. 钻完立柱Start/run the shale shaker. 开振动筛Start the desanders. 开除砂器Start the desilters. 开除泥器Change it with a 40 mesh screen. 换成40目筛布Shut it off. 关掉Pull it to the cat ramp. 把它拉到坡道上去Make a fast connection. 接单根要快Don’t dump the mud into the sea. 不要把泥浆排放到海里Disconnect it with a chain tong. 用链钳卸开Put a thread protector. 加一个(丝扣)护箍Can we use the power slips? 可以使用动力卡瓦吗?Casing and Cementing 下套管与固井Run in hole to bottom for wiper trip. 下钻通井This is the casing program. 这是套管程序Prepare for running casing. 准备下套管Make everything ready for running 7”casing. 做好下7”套管的准备Make cementing job. 固井Displace cementing with mud pump. 用泥浆泵替泥浆Set cement plug from 2940 to 2790m. 在2940到2790米井段打水泥塞Pick up cementing head. 接水泥头Cement samples are hard. 水泥样已凝固Pump in 3 cubic meters of spacer. 注3方隔离液Pump down the plug. 泵压(胶)塞Wait on cement. 候凝The guide shoe will be connected. 接引鞋Connect the floor collar. 接浮箍Connect the air line to the casing stabbing board. 接好套管扶正台的气管线Run casing with the 350T slip elevator. 用350吨卡瓦式吊卡下套管Clean and dry 20”casing threads with rags. 清洁并擦干20”套管丝扣Where is the rabbit for drifting the casing? 套管通径规在哪里?Rig Move, Anchoring and Positioning 拖航, 抛锚, 定位What is our position now? 我们现在船位在哪里?What’s the moving speed now? (What’s the towering speed?) 拖航速度是多少? The speed is about 4 knots. 船速是4节左右Which one is the main tug? 主拖是哪条船?The main tug is Nanhai 205. 主拖是南海205Which one is the chase boat? 护航船是哪一条?How much is the horse power? 有多大马力?She has 6000 HP. 有6000马力Move the rig off location 50 feet. 将平台移开50英尺We are ready to drop the anchor. 我们已经做好抛锚的准备了Secure all the movable equipment. 固定好各种活动的设备Preload. (自升式)压载Ballast. (半潜式)压载Put the preload water into the tank. 向压载舱灌压压载水We need 5500 tons of preload water. 需要5500吨压载水Shall we preload right now? 马上开始压载吗?Drain the water off. 放水The rig is overloaded. 平台已超载Jack up (jack down) the rig. 升(降)船The draft is 3.5 meters. 船体吃水3.5米The jetting pressure is 100psi. 冲桩压力是100psiPenetrate the legs. 插桩How much penetration do we have? 入泥多深了?No.1 and No.2 legs indicate 10 meters. 1,2号桩腿插入10米Fix the upper and lower wedges. 固定上下楔块Pay out the anchor line. 放出锚缆绳Skid the derrick. 移开井架The rig is short of potable water now. 平台缺乏饮用水Drop No.2 and No.3 anchors. 抛2号和3号锚Why has the main engine stopped? 主机为什么停?Unleash the drilling tools. 卸开钻具Tighten up. 绷紧(或:上紧)一点Turn on the cooling water for the windlasses. 开锚机刹车冷却水Retrieve the No.1 to No.8 anchors. 起1到8号锚Check the paint marks at the anchor winches. 检查锚机上的油漆记号Prepare for a location move. 准备好移井位Commence anchor handling. 开始起锚(或抛锚)Secure all equipment stored on deck. 固定好所有存放在甲板上的设备Carry out stability and load calculations. 做稳性和载荷计算Pass pendant line, shackle and buoy to anchor handling vessel. 将起抛锚短索, 卸扣和浮标吊起给起锚船Lower the windward anchor to seafloor. 抛上风锚到海底Pick up the leeward anchor first. 先起下风锚Take anchor chaser (or chaser) back to rig. 将捞/抛锚环送回平台Hook up towing lines to tug boat. 将拖缆连接到拖轮Sound fog signal for two seconds every twenty seconds. 发大雾信号, 每20秒钟响两秒Fishing 打捞The bit cutters have been lost in the hole. 牙轮落井Run in the reverse-circulation basket. 下反循环打捞篮There is a lot of junk in the hole. 井下有很多落物The fish is 235.46 meters long. 落鱼长度235.46米The fish top is at 2478.34 meters. 鱼顶位置2478.34米Coring 取芯Stop drilling for coring. 停钻准备取芯Make up core bit. 接取芯钻头A-60 fire door A-60级防火门abrasive (喷砂用的)磨料abrasive paper 砂纸AC generator 交流发电机AC motor 交流电动机accelerated corrosion testing 加速腐蚀试验acceptance criteria 合格准则access hole (for welding)=cope hole 焊接工艺孔acetylene gas 乙炔acid electrode 酸性焊条acid proof cement 防酸水泥additive 添加剂AFC (approved for construction) 建造批准agitator 搅拌器air blower 鼓风机air compressor 空压机air drive pump 气动泵。
