紧固件GB大全以及美制英制德标对照表

紧固件国标德标国际标准对应表螺丝标准及国标德标国际标准对应表中文品名德国标准中国标准国际标准英文品名自攻自钻螺钉多种头型DIN7504 GB15856.1-4 Self-drilling tapping screws平垫DIN125-A GB97.1-85 ISO7089 Plain washers平垫（带倒角）DIN125-B GB97.2-85 ISO7090 Mediun washers平垫DIN126 ISO7091 Plain washers重型弹垫DIN127-A GB7244 Spring lock washers,tang ends标准弹垫DIN127-B GB93-87 Spring lock washers,square ends内六角扳手DIN911 ISO2936 Socket wrenches内六角圆柱头螺钉DIN912 GB70-85 ISO4762 Hexagon socket cap screws内六角平端紧定螺钉DIN913 GB77-85 ISO4026 Hexagon socket set screws with falt point内六角尖端紧定螺钉DIN914 GB78-85 ISO4027 Hexagon socket set screws with cone point 内六角圆柱端紧定螺钉DIN915 GB79-85 ISO4028 Hexagon socket set screws with dog point 内六角凹端紧定螺钉DIN916 GB80-85 ISO4029 Hexagon socket set screws with cup point 六角头螺栓）（半牙）DIN931 GB5782-86 ISO4014 Hexagon head screws六角头螺栓（全牙）DIN933 GB5783-86 ISO4017 Hexagon head screws开槽沉头螺钉DIN963 GB68-85 ISO2009 Slotted countersund head screws开槽半沉头螺钉DIN964 GB69-85 ISO2010 Slotted raised countersunk oval head screws 十字槽沉头螺钉DIN965 GB819-85 ISO7046 Cross recessed countersunk head screws十字槽半沉头螺钉DIN966 GB820-85 ISO7047 Cross recessed raised十字槽盘头自攻螺攻DIN7981 GB845-85 ISO7049 Pan head tapping screws with cross recessed十字槽沉头自攻螺攻DIN7982 GB846-85 ISO7050Countersunk flat head tapping screws with crossrecessed十字槽半沉头自攻螺攻DIN7983 GB847-86 ISO7051Raised countersunk oval head tapping screws withcross开槽盘头自攻螺钉DIN7971 GB5282-85 ISO1481 Pan head tapping screws with slot开槽沉头自攻螺钉DIN7972 GB5283-85 ISO1482 countersunk flat head tapping screws with slot开槽半沉头自攻螺钉DIN7973 GB5284-85 ISO1483Raised sountersunk oval head tapping screws withslot六角头自攻螺钉DIN7976 GB5285-85 ISO1479 Hexagon tapping screws十字槽盘头螺钉DIN7985 GB818-85 ISO7045 Pan head screws with cross recessed内六角沉头螺钉DIN7991 ISO10642 Hexagon socket coutersunk head screws六角头尼龙锁紧螺母DIN982 GB812-88 ISO2982Prevailing rorque type hexagon nuts,heavytype,with nylon六角头薄型尼龙锁紧螺母DIN985 GB889.1-86 ISO7040Prevalling torque type hoxagon nuts,heavytype,with nylon六角盖型尼龙锁紧螺母DIN986 GB6172.2-86 ISO10511Preailling torque typedomed capnuts with nyloninsert六角头螺母（ 1 型）DIN934 GB6170-86 ISO4032 Hexagon full nuts细牙六角头螺母（ 1型）DIN934 GB6171-86 ISO8673 Hexagon full nuts六角头薄螺母DIN936 GB6172.1-86 ISO4035 Hexagon thin nuts六角薄螺母DIN439 GB6172-86 ISO4035 Hexagon thin nuts开槽半沉头木螺钉DIN95 GB101 Slotted raised csk head wood screws 开槽半圆头木螺钉DIN96 GB99 Slotted round head wood screws开槽沉头木螺钉DIN97 GB100 Slotted countersunk head wood screws 鞍形弹垫DIN128-A GB7245-87 Single coil spring lock washers弹簧止动垫圈DIN137-A Curved spring washers波形弹垫DIN137-B GB955 Wave spring washersT 型方颈螺栓DIN186 GB37-88 T-head blots with square neckT 型双接头螺栓DIN188 T-head bolts with double nip螺纹圆锥销DIN258 ISO8737 Taper pins with threaded endT 型头螺栓DIN261 T-head bolts蝶型螺母（美制）DIN315AF Wing nuts America form蝶型螺母（德制）DIN315DF GB62-88 Wing nuts germany form蝶型螺母（美制）DIN316AF Wing screws America form蝶型螺母DIN317DF Wing screws germany form（德制）圆球型盖型DIN319 Ball knobs螺母开槽带孔球DIN404 GB832-88 Slotted capstan screws面圆柱头蚴钉开槽长圆柱DIN417 GB75-85 ISO7435 Slotted set srews with full dog point端紧定螺钉开槽平端紧DIN427 GB73-85 ISO2342 Slotted set srews with chamfered end定螺钉（半牙）小六角特薄DIN431 GB808-88 Pip nuts with thread细牙螺母外舌止动垫DIN432 GB856-88 External tap圈小垫圈(用DIN433 GB848-95 ISO7092 Washers for cheese head screws于圆柱头螺钉)方斜垫圈DIN434 GB852-88 Square taper washers for（ U 型）方斜垫圈DIN435 GB852-88 Square taper washers for（ I 型）方垫圈DIN436 Square washers开槽凹端紧DIN438 GB74-85 ISO7436 Slotted set with cup point定螺钉细牙六角薄DIN439 GB6173-86 ISO8675 Hexagon thin nuts螺母木螺钉专用DIN440 ISO7094 Rounds washers for wood constructions垫圈密封帽DIN443 Sealing caps,push-in type活节螺栓 BDIN444 GB798-88 Eye bolts form B型内舌止动垫DIN462 Internal tab washers圈双耳止动垫DIN463 GB855-88 Washers with two taps圈滚花高头螺DIN464 GB834-88 Knurled thumb screws with collar钉开槽滚花高DIN465 Slotted knurled thumb screws with collar 头螺钉滚花高螺母DIN466 GB806-88 Knurled thumb nuts with collar滚花薄螺母DIN467 GB807-88 Knurled thumb thin nuts锁紧垫圈DIN470 Sealing washers轴用弹性垫DIN471 GB893-86 Retaining rings for shafts(external),circlips 圈孔用弹性垫DIN472 GB893.86 Retaining rings for bores(internal),circlips圈方头带垫螺DIN478 Square head bolts with collar栓方头圆柱底DIN479 Square head bolts with half dog point端螺栓方头带垫关DIN480 Square head bolts with collar,half dog point圆底端螺栓T 型槽螺母DIN508 ISO299 T-slot nuts单头螺柱DIN525 Single end studs地脚螺栓DIN529 GB799-88 Masonry bolts带槽圆螺母DIN546 GB817-76 Slotted round nuts端面带孔圆DIN547 GB815-88 Round nuts with drilled holes in one face螺母开槽平端紧DIN551 GB73-85 ISO4776 Slotted set screws with flat point定螺钉开槽锥端紧DIN553 GB71-85 ISO7434 Slotted set screws with cone point定螺钉六角螺母DIN555 ISO4034 Hexagon nuts方螺母 -C DIN557 GB39-88 Square nuts六角头螺钉DIN558 ISO4018 Hexagon screws六角头圆柱DIN561 Hexagon set screws with full dog point端紧定螺钉薄型方螺母DIN562 Square nuts without bevel-B六角头木螺DIN571 GB102-86 Hexgon head wood screw钉吊环螺钉DIN580 GB825-76 ISO3266 Lifting eye bolts吊环螺母DIN582 Lifting eye nuts六角头螺栓DIN601 ISO4016 Hexagon blots大半圆头方DIN603 GB14-88 ISO8677 Mushroom head square neck bolts(carriage bolts) 颈螺栓（马车螺栓）沉头带插销DIN604 Flat countersunk nib bolts马车螺栓沉头长方颈DIN605 Flat countersunk long squareneck bolts马车螺栓半圆头带插DIN607 Cup head nib bolts销马车螺栓沉头短方颈DIN608 Flat countersunk short square neck bolts马车螺栓六角头精配DIN609 Hexagon fitted bolts,long thread螺栓（长螺纹）六角头精配DIN610 Hexagon fitted bolts short thread螺栓（短螺栓）滚花平头螺DIN653 GB835-88 Knurled thumb screws thin type钉半圆头铆钉DIN660 GB867-86 ISO1051 Round head rivets沉头铆钉DIN661 GB869-86 ISO1051 Contersunk head rivets半沉头铆DIN662 ISO1051 Raised contersunk head rivets钉大扁头铆钉DIN674 ISO1051 Mushroom head rivets重型侧面带DIN703 Adjusting rings,heavy range(shafting collars) 孔圆螺母侧面带孔圆DIN705 GB816-88 Adjusting rings,light range(shafting collars) 螺母卡头DIN741 Wire rope clipsT 型槽螺钉DIN787 ISO299 T-slot screws双头螺柱DIN835 GB900-88 Studs-metal(end=2d)（牙长=2D ）内六角锥型DIN906 Hexagon socket pipe plugs,conical thread闭锁螺钉内六角直型DIN908 Thread闭锁螺钉外六角锥型DIN909 Thread闭锁螺钉外六角直型DIN910 Hexagon head screw plugs,cyl.thread闭锁螺钉薄型盲螺母DIN917 Hexagon cap nuts开槽小圆柱DIN920 Slotted short cheese head screws头螺钉开槽大圆柱DIN921 GB838-88 Slotted large cheese head screws头螺钉开槽圆柱头DIN923 GB830-88 Slotted pan head screw with shoulder轴肩螺钉开槽无头轴DIN927 Slotted shoulder screws肩螺钉焊接方螺母DIN928 GB/T13680-92 Square weld nuts焊接六角螺DIN929 GB/T13681-92 Hexagon weld nuts母六角头螺母DIN970 Hexagon nuts type-1六角头螺母DIN971 Hexagon nuts type-2细牙六角头DIN972 Hexagon nuts with fine thread螺母（ 2型）开槽六角螺DIN935 GB6178-86 ISO7035 Hexagon slotted and castle nuts母六角头开槽DIN937 GB6181-86 ISO7038 Hexagon thin slotted and caslte nuts薄螺母双头螺距DIN938 GB897-88 Studs metal(end=1d)（牙长=1D ）双头螺距DIN939 GB898-88 Studs metal(end=1.25d)（牙长=1.5D双头螺距DIN940 Studs metal(end=1.5d)（牙长=1.25D六角头细牙DIN960 GB5785-86 ISO8765 Hexagon head bolts,metric fine pitch thread螺栓（全牙）六角头细牙DIN961 GB8786-86 ISO8676 Hexagon head bolts,metric fine pitch thread螺栓（半牙）头部穿孔六DIN962 Additional shapes and versions for bolts角头螺栓牙条（全螺DIN975 GB6176-86 ISO8674 Threaded rods(studdings)纹）螺纹销DIN976 GB15389-94 Threaded pins(stud bolts)六角头开槽DIN979 Hexagon thin slotted and castle nuts薄螺母2 型全金属六角DIN980 Prevaillng rorque type hexagon nuts,all metal nuts 锁紧螺母 1型圆螺母DIN981 GB6184-86 ISO7199 Locknuts配合垫片DIN988 Shim rings木材连接用DIN1052 Washers for timber connectors垫片沉头钢钉DIN1151 Round plain head nails销钉专用垫DIN1440 ISO8738 Plain washers for clevis pins(A 型)片 A 型销钉专用垫DIN1441 Plain washers for clevis pins片带头销钉DIN1444 ISO2341 Clevis pins with head圆锥型槽销DIN1471 GB/T13829.2 ISO8744 Grooved pins,taper grooved圆锥型槽销DIN1472 GB/T13829.2 ISO8745 Grooved pins,taper grooved half length（半槽）平行槽销DIN1473 ISO8740 Grooved pins,parallel grooved full length（带倒角）前端凹槽槽DIN1474 ISO8741 Grooved pins,reverve grooved half length销中部凹槽槽DIN1475 ISO8742 Grooved pins,center grooved销圆头槽销DIN1476 ISO8746 Grooved pins with round head沉头槽销DIN1477 ISO8747 Grooved pins with countersunk head六角螺母棒DIN1479 Turnuckles(center parts),made out of hexagon bar花蓝螺栓DIN1480 Turnuckles with eye bolt and hook bolt弹性圆柱销DIN1481 GB879-86 ISO8752 Spring pins,heavy type组合式盖型螺母DIN1587 GB802-88 Hexagon domed cap nuts开槽圆螺母(配合沟头扳手)DIN1804 Slotted round nuts for hook spammer圆螺母（带插销孔）DIN1816 Round nuts with set holes盘型弹簧垫圈DIN2093 Disc springs喉箍DIN3017 Hose clamps润滑油嘴（旋扭头）DIN3404 Lubricating nipples,button head管夹DIN3567 Shackles for conduiltsU 型螺栓DIN3570 Stirrup bolts(U-bolts)球面垫圈DIN6319 GB849-88 Spherical washers,conical seats圆柱销DIN6325 ISO8734 Parallel pins厚六角螺母DIN6330 GB56-88 Hexagon nuts,1.5d厚六角法兰面螺母DIN6331 GB6177-86 Hexagon nuts,1.5d with collar长六角螺母DIN6334 Hexagon nuts,3d外齿锁紧垫圈DIN6797-A GB862.1-87 External teeth lock washers内齿锁紧垫圈DIN6797-I GB861.1-87 Internal teeth lock washers外锯齿锁紧垫圈DIN6798-A GB862.2-87 External teeth serrated lock washers内锯齿锁紧垫圈DIN6798-I GB861.2-87 Internal teeth serrated lock washers开口挡圈DIN6799 GB896-76 Retaining rings for shafts(E-rings),circlips 平键（ A型）DIN6885 ISO773/2491 Parallel keys(form A)半圆键DIN6888 ISO3912 Woodruff keys嵌环（支撑环）DIN6899 Thimbles机器螺钉和垫圈组合件DIN6900 Screws and washers assemblies自攻螺钉和垫圈组合件DIN6901 GB9074.1-17 Tapping screws and washer assemblies薄型带孔内六角圆柱螺钉DIN6912 GB9074.18-23Hexagon cocket head cap screws with hole,lowhead大六角头螺栓DIN6914 Hexagon head bolts with large head大六角螺母DIN6915 Hexagon nuts with large wideth across flat大垫圈DIN6916 Round washers for friction grip bolts楔型方垫圈DIN6917 Spuare taper washers for friction grip bolts on T-六角法兰面螺母DIN6923 GB6187-86 ISO4161 Hexagon flange nuts全金属六角锁紧螺母 2 型DIN6925 GB6185.1-2000 ISO7042Prevailing torque type hexagon nuts,all metallicnuts轻型弹性圆柱销DIN7346 ISO13337 Spring pins,light type重型弹性圆柱销用垫圈DIN7349 Washers for bolts with heavy type spring pinss ISO 公制螺纹螺钉多种头型DIN7500 Thread forming screws for ISO-metric thread开槽切削螺纹螺钉（多种头型）DIN7513 Thread cutting screws十字槽切削螺纹螺钉（多种头型）DIN7516 Thread cutting screws cross recessT 型四爪螺母DIN7965 Tee nuts with pronge钢结构用六角头螺栓连接副DIN7968 GB1228/1229/1230 Hexagon head fitted bolts for steel structures圆柱头螺钉用弹簧垫圈DIN7980 ISO8738Spring lock washers for screws with cylindricalheads薄型内六角圆柱头螺钉DIN7984Hexagon socket head cap screws with,reducedhead钢结构用垫圈DIN7989 GB1230-84 Washers for steel structures钢结构用六角头螺栓DIN7990 GB1229-84 Hexagon head bolts for steel structures 轴用钢丝挡圈DIN7993 GB895.2-86 Roundwire snap rings for shafts十字槽半沉头木螺钉DIN7995 GB952-86Cross recessed raised countersunk head woodscrews十字槽圆头木螺钉DIN7996 GB950-86 Cross recessed round head wood screws十字槽沉头木螺钉DIN7997 GB951-86 Cross recessed countersunk head wood screws 螺纹护套DIN8140 Ciol inserts,coarse,fine thread,silf locking(普通、自锁等)大外径垫圈DIN9021 GB96-85 ISO7093 Washers,outside diameter appro.3d 弹簧卡子DIN11024 sping cotter for a bolt平板螺栓DIN13257 Belting bolts(elevator bolts)干壁钉（墙DIN18182 Dry wall screws板钉）环型螺母DIN28129 GB63-88 Lifting nuts(eye nuts)圆螺母用止DIN70952 Tab washer for slotted round nuts 退圆锥销DIN1 GB117 ISO2339 Taper pins圆柱销DIN7 GB119-86 ISO2339 Parallel pins开槽圆柱头DIN84 GB65-85 ISO1207 Slotted cheese head screws螺钉开槽盘头螺DIN85 GB67-85 ISO1580 Slotted pan head screws钉单耳止动垫DIN93 GB854 Tab washers圈开口销DIN94 GB91 ISO1234 Split cooter pins。

德国标准和国际标准、中国标准中英文对照表序号德国标准中文品名英文品名国际标准中国标准Item DIN-Standard Description in Chinese Description in English ISO-Standard GB-Standard1 DIN1 圆锥销taper pins ISO2339 GB1172 DIN7 圆柱销parallel pins ISO2338 GB119-863 DIN84 开槽圆柱头螺钉slotted cheese head screws ISO1207 GB65-854 DIN85 开槽盘头螺钉slotted pan head screws ISO1580 GB67-855 DIN93 单耳止动垫圈tab washers GB8546 DIN94 开口销split cotter pins ISO1234 GB917 DIN95 开槽半沉头木螺钉slotted raised csk head wood screws GB1018 DIN96 开槽半圆头木螺钉slotted round head wood screws GB999 DIN97 开槽沉头木螺钉slotted countersunk head wood screws GB10010 DIN125-A 平垫plain washers ISO7089 GB97.1-8511 DIN125-B 平垫(带倒角) mediun washers ISO7090 GB97.2-8512 DIN126 平垫plain washers ISO709113 DIN127-A 重型弹垫spring lock washers,tang ends GB724414 DIN127-B 标准弹垫spring lock washers,square ends GB93-8715 DIN128-A 鞍形弹垫single coil spring lock washers GB7245-8716 DIN137-A 弹簧止动垫圈curved spring washers17 DIN137-B 波形弹垫wave spring washers GB95518 DIN186 T型方颈螺栓T-head bolts with square neck GB37-8819 DIN188 T型双接头螺栓T-head bolts with double nip20 DIN258 螺纹圆锥销taper pins with threaded end ISO873721 DIN261 T型头螺栓T-head bolts22 DIN315AF 蝶型螺母(美制) wing nuts amercia form23 DIN315DF 蝶型螺母(德制) wing nuts germany form GB62-8824 DIN316AF 蝶型螺钉(美制) wing screws amercia form25 DIN317DF 蝶型螺钉(德制) wing screws germany form26 DIN319 圆球型盖型螺母ball knobs27 DIN404 开槽带孔球面圆柱头螺钉slotted capstan screws GB832-8828 DIN417 开槽长圆柱端紧定螺钉slotted set srews with full dog point ISO7435 GB75-8529 DIN427 开槽平端紧定螺钉(半牙) slotted set srews with chamfered end ISO2342 GB73-8530 DIN431 小六角特薄细牙螺母pipe nuts with thread GB808-8831 DIN432 外舌止动垫圈external tap GB856-8832 DIN433 小垫圈(用于圆柱头螺钉) washers for cheese head screws ISO7092 GB848-9533 DIN434 方斜垫圈(U型) square taper washers for U-section GB852-8834 DIN435 方斜垫圈(I型) square taper washers for I-sections GB852-8835 DIN436 方垫圈square washers36 DIN438 开槽凹端紧定螺钉slotted set with cup point ISO7436 GB74-8537 DIN439 六角薄螺母hexagon thin nuts ISO4035 GB6172-8638 DIN439 细牙六角薄螺母hexagon thin nuts ISO8675 GB6173-8639 DIN440 木螺钉专用垫圈rounds washers for wood constructions ISO709440 DIN443 密封帽sealing caps,push-in type41 DIN444 活节螺栓B 型eye bolts form B GB798-8842 DIN462 内舌止动垫圈internal tab washers43 DIN463 双耳止动垫圈washers with two taps GB855-8844 DIN464 滚花高头螺钉knurled thumb screws with collar GB834-8845 DIN465 开槽滚花高头螺钉slotted knurled thumb screws with collar46 DIN466 滚花高螺母knurled thumb nuts with collar GB806-8847 DIN467 滚花薄螺母knurled thumb thin nuts GB807-8848 DIN470 锁紧垫圈sealing washers49 DIN471 轴用弹性挡圈retaining rings for shafts(external),circlips GB894.1-8650 DIN472 孔用弹性挡圈retaining rings for bores(internal),circlips GB893.1-8651 DIN478 方头带垫螺栓square head bolts with collar52 DIN479 方头圆柱底端螺栓square head bolts with half dog point53 DIN480 方头带垫半圆底端螺栓square head bolts with collar,half dog point and rounded end54 DIN508 T型槽螺母T-slot nuts ISO29955 DIN525 单头螺柱single end studs56 DIN529 地脚螺栓masonry bolts GB799-8857 DIN546 带槽圆螺母slotted round nuts GB817-7658 DIN547 端面带孔圆螺母round nuts with drilled holes in one face GB815-8859 DIN551 开槽平端紧定螺钉slotted sit screws with flat point ISO4776 GB73-8560 DIN553 开槽锥端紧定螺钉slotted set screws with cone point ISO7434 GB71-8561 DIN555 六角螺母hexagon nuts ISO403462 DIN557 方螺母-C square nuts GB39-8863 DIN558 六角头螺钉hexagon screws ISO401864 DIN561 六角头圆柱端紧定螺钉hexagon set screws with full dog point65 DIN562 薄型方螺母-B square nuts without bevel(pressed nuts)66 DIN571 六角头木螺钉hexagon head wood screws (coach screws) GB102-8667 DIN580 吊环螺钉lifting eye bolts ISO3266 GB825-7668 DIN582 吊环螺母lifting eye nuts69 DIN601 六角头螺栓hexagon bolts ISO401670 DIN603 大半圆头方颈螺栓(马车螺栓) mushroom head square neck bolts (carriage bolts) ISO8677 GB14-8871 DIN604 沉头带插销马车螺栓flat countersunk nib bolts72 DIN605 沉头长方颈马车螺栓flat countersunk long square neck bolts73 DIN607 半圆头带插销马车螺栓cup head nib bolts74 DIN608 沉头短方颈马车螺栓flat countersunk short square neck bolts75 DIN609 六角头精配螺栓（长螺纹）hexagon fitted bolts,long thread76 DIN610 六角头精配螺栓（短螺纹）hexagon fitted bolts,short thread77 DIN653 滚花平头螺钉knurled thumb screws thin type GB835-8878 DIN660 半圆头铆钉round head rivets ISO1051 GB867-8679 DIN661 沉头铆钉contersunk head rivets ISO1051 GB869-8680 DIN662 半沉头铆钉raised contersunk head rivets ISO105181 DIN674 大扁头铆钉mushroom head rivets ISO105182 DIN703 重型侧面带孔圆螺母adjusting rings,heavy range (shafting collars)83 DIN705 侧面带孔圆螺母adjusting rings,light range (shafting collars) GB816-8884 DIN741 卡头wire rope clips85 DIN787 T型槽螺钉T-slot screws ISO29986 DIN835 双头螺柱（牙长=2D）studs-metal (end=2d) GB900-8887 DIN906 内六角锥型闭锁螺钉hexagon socket pipe plugs,conical thread88 DIN908 内六角直型闭锁螺钉hexagon socket screw plugs,cyl. thread89 DIN909 外六角锥型闭锁螺钉hexagon head pipe plugs,conical thread90 DIN910 外六角直型闭锁螺钉hexagon head screw plugs,cyl.thread91 DIN911 内六角扳手socket wrenches ISO293692 DIN912 内六角圆柱头螺钉hexagon socket cap screws ISO4762 GB70-8593 DIN913 内六角平端紧定螺钉hexagon socket set screws with flat point ISO4026 GB77-8594 DIN914 内六角尖端紧定螺钉hexagon socket set screws with cone point ISO4027 GB78-8595 DIN915 内六角圆柱端紧定螺钉hexagon socket set screws with dog point ISO4028 GB79-8596 DIN916 内六角凹端紧定螺钉hexagon socket set screws with cup point ISO4029 GB80-8597 DIN917 薄型盲螺母hexagon cap nuts98 DIN920 开槽小圆柱头螺钉slotted short cheese head screws99 DIN921 开槽大圆柱头螺钉slotted large cheese head screws GB838-88100 DIN923 开槽圆柱头轴肩螺钉slotted pan head screws with shoulder GB830-88101 DIN927 开槽无头轴肩螺钉slotted shoulder screws102 DIN928 焊接方螺母square weld nuts GB/T13680-92103 DIN929 焊接六角螺母hexagon weld nuts GB/T13681-92104 DIN931 六角头螺栓（半牙）hexagon head screws ISO4014 GB5782-86105 DIN933 六角头螺栓（全牙）hexagon head screws ISO4017 GB5783-86106 DIN934 六角头螺母(1型) hexagon full nuts ISO4032 GB6170-86107 DIN934 细牙六角头螺母(1型) hexagon full nuts ISO8673 GB6171-86108 DIN935 开槽六角螺母hexagon slotted and castle nuts ISO7035 GB6178-86109 DIN936 六角头薄螺母hexagon thin nuts ISO4035 GB6172.1-86110 DIN937 六角头开槽薄螺母hexagon thin slotted and castle nuts ISO7038 GB6181-86111 DIN938 双头螺距（牙长=1D）studs metal (end=1d) GB897-88112 DIN939 双头螺距（牙长=1.25D）studs metal (end=1.25d) GB898-88113 DIN940 双头螺距（牙长=1.5D）studs metal (end=1.5d)114 DIN960 六角头细牙螺栓（半牙）hexagon head bolts,metric fine pitch thread ISO8765 GB5785-86115 DIN961 六角头细牙螺栓（全牙）hexagon head bolts,metric fine pitch thread ISO8676 GB5786-86116 DIN962 头部穿孔六角头螺栓additional shapes and versions for bolts117 DIN963 开槽沉头螺钉slotted countersund head screws ISO 2009 GB68-85118 DIN964 开槽半沉头螺钉slotted raised countersunk oval head screws ISO 2010 GB69-85 119 DIN965 十字槽沉头螺钉cross recessed countersunk head screws ISO7046 GB819-85120 DIN966 十字槽半沉头螺钉cross recessed raised countersunk head screws ISO7047 GB820-85121 DIN970 六角头螺母hexagon nuts type-1122 DIN971 六角头螺母hexagon nuts type-2123 DIN972 细牙六角头螺母(2型) hexagon nuts with fine thread ISO8674 GB6176-86124 DIN975 牙条(全螺纹) threaded rods(studdings) GB15389-94125 DIN976 螺纹销threaded pins(stud bolts)126 DIN979 六角头开槽薄螺母（2型）hexagon thin slotted and castle nuts127 DIN980 全金属六角锁紧螺母（1型）prevailling torque type hexagon nuts,all metall nuts ISO7199 GB6184-86128 DIN981 圆螺母locknuts ISO2982 GB812-88129 DIN982 六角头尼龙锁紧螺母prevailling torque type hexagon nuts,heavy type ,with nylon insert ISO7040 GB889.1-86130 DIN985 六角头薄型尼龙锁紧螺母prevailling torque type hexagon nuts,heavy type ,with nylon insert ISO10511 GB6172.2-86131 DIN986 六角盖型尼龙锁紧螺母prevailling torque typedomed capnuts with nylon insert132 DIN988 配合垫片shim rings133 DIN1052 木材连接用垫片washers for timber connectors134 DIN1151 沉头钢钉round plain head nails135 DIN1440 销钉专用垫片A型plain washers for clevis pins(A型) ISO8738136 DIN1441 销钉专用垫片plain washers for clevis pins137 DIN1444 带头销钉clevis pins with head ISO2341138 DIN1471 圆锥型槽销grooved pins,taper grooved ISO8744 GB/T13829.2139 DIN1472 圆锥型槽销(半槽) grooved pins,taper grooved half length ISO8745 GB/T13829.2 140 DIN1473 平行槽销(带倒角) grooved pins,parallel grooved full length ISO8740141 DIN1474 前端凹槽槽销grooved pins,reserve grooved half length ISO8741142 DIN1475 中部凹槽槽销grooved pins,centre grooved ISO8742143 DIN1476 圆头槽销grooved pins with round head ISO8746 GB/T13829.3144 DIN1477 沉头槽销grooved pins with countersunk head ISO8747145 DIN1479 六角螺母棒turnuckles(centre parts),made out of hexagon bar146 DIN1480 花篮螺栓turnuckles with eye bolt and hook bolt147 DIN1481 弹性圆柱销spring pins,heavy type ISO8752 GB879-86148 DIN1587 组合式盖型螺母hexagon domed cap nuts GB802-88149 DIN1804 开槽圆螺母（配合沟头扳手）slotted round nuts for hook spanner150 DIN1816 圆螺母（带插销孔）round nuts with set holes151 DIN2093 盘型弹簧垫圈disc springs152 DIN3017 喉箍hose clamps153 DIN3404 润滑油嘴（旋扭头）lubricating nipples,button head154 DIN3567 管夹shackles for conduilts155 DIN3570 U型螺栓stirrup bolts(U-bolts)156 DIN6319 球面垫圈spherical washers,conical seats GB849-88157 DIN6325 圆柱销parallel pins ISO8734158 DIN6330 厚六角螺母hexagon nuts ,1.5d GB56-88159 DIN6331 厚六角法兰面螺母hexagon nuts ,1.5d with collar GB6177-86160 DIN6334 长六角螺母hexagon nuts ,3d161 DIN6797-A 外齿锁紧垫圈external teeth lock washers GB862.1-87162 DIN6797-I 内齿锁紧垫圈internal teeth lock washers GB861.1-87163 DIN6798-A 外锯齿锁紧垫圈external teeth serrated lock washers GB862.2-87164 DIN6798-I 内锯齿锁紧垫圈internal teeth serrated lock washers GB861.2-87165 DIN6799 开口挡圈retaining rings for shafts(E-rings),circlips GB896-76166 DIN6885 平键（A型）parallel keys(form A ) ISO773/2491167 DIN6888 半圆键woodruff keys ISO3912168 DIN6899 嵌环（支撑环）thimbles169 DIN6900 机器螺钉和垫圈组合件screws and washers assemblies GB9074.1-.17170 DIN6901 自攻螺钉和垫圈组合件tapping screws and washers assemblies GB9074.18-.23 171 DIN6912 薄型带孔内六角圆柱头螺钉hexagon socket head cap screws with hole,low head 172 DIN6914 大六角头螺栓hexagon head bolts with large head(friction grip bolts)173 DIN6915 大六角螺母hexagon nuts with large wideth across flat(friction grip nuts)174 DIN6916 大垫圈round washers for friction grip bolts175 DIN6917 楔型方垫圈spuare taper washers for friction grip bolts on T-sections176 DIN6923 六角法兰面螺母hexagon flange nuts ISO4161 GB6177-86177 DIN6925 全金属六角锁紧螺母(2型）prevailing torque type hexagon nuts,all metallic nuts ISO7042 GB6185.1-2000178 DIN7337 开口型抽芯铆钉（沉头、扁圆头）blind rivets GB12617/12618179 DIN7338 扁平头半空心/全空心铆钉rivets for brake and clutch lining GB875/975-86180 DIN7343 螺旋夹紧销spiral pins ISO8750181 DIN7346 轻型弹性圆柱销spring pins,light type ISO13337182 DIN7349 重型弹性圆柱销用垫圈washers for bolts with heavy type spring pinss183 DIN7500 ISO公制螺纹螺钉(多种头型) threadforming screws for ISO-metric thread184 DIN7504 自攻自钻螺钉(多种头型) self-drilling tapping screws185 DIN7513 开槽切削螺纹螺钉(多种头型) thread cutting screws186 DIN7516 十字槽切削螺纹螺钉(多种头型) thread cutting screws cross recess187 DIN7965 T型四爪螺母tee nuts with pronge188 DIN7968 钢结构用六角头螺栓连接副hexagon head fitted bolts for steel structures GB1228/1229/1230189 DIN7971 开槽盘头自攻螺钉pan head tapping screws with slot ISO1481 GB5282-85190 DIN7972 开槽沉头自攻螺钉countersunk flat head tapping screws with slot ISO1482 GB5283-85191 DIN7973 开槽半沉头自攻螺钉raised countersunk oval head tapping screws with slot ISO1483 GB5284-85192 DIN7976 六角头自攻螺钉hexagon tapping screws ISO1479 GB5285-85193 DIN7980 圆柱头螺钉用弹簧垫圈spring lock washers for screws with cylindrical heads ISO8738194 DIN7981 十字槽盘头自攻螺钉pan head tapping screws with cross recessed ISO 7049 GB845-85195 DIN7982 十字槽沉头自攻螺钉countersunk flat head tapping screws with cross recessed ISO7050 GB846-85196 DIN7983 十字槽半沉头自攻螺钉raised countersunk oval head tapping screws with cross recessed ISO7051 GB847-86197 DIN7984 薄型内六角圆柱头螺钉hexagon socket head cap screws with，reduced head198 DIN7985 十字槽盘头螺钉pan head screws with cross recessed ISO7045 GB818-85199 DIN7989 钢结构用垫圈washers for steel structures GB1230-84200 DIN7990 钢结构用六角头螺栓hexagon head bolts for steel structures GB1229-84201 DIN7991 内六角沉头螺钉hexagon socket countersunk head screws ISO10642202 DIN7993 轴用钢丝挡圈roundwire snap rings for shafts GB895.2-86203 DIN7995 十字槽半沉头木螺钉cross recessed raised countersunk head wood screws GB952-86204 DIN7996 十字槽圆头木螺钉cross recessed round head wood screws GB950-86205 DIN7997 十字槽沉头木螺钉cross recessed countersunk head wood screws GB951-86206 DIN8140 螺纹护套（普通\自锁等）ciol inserts,coarse,fine thread,silf locking207 DIN9021 大外径垫圈washers,outside diameter appro.3d ISO7093 GB96-85208 DIN11024 弹簧卡子spring cotter for a bolt209 DIN13257 平板螺栓belting bolts (elevator bolts)210 DIN18182 干壁钉（墙板钉）dry wall screws211 DIN28129 环型螺母lifting nuts(eye nuts) GB63-88212 DIN70952 圆螺母用止退垫圈tab washers for slotted round nuts GB858-88。

紧固件规格标准——GB标准档圈锥销锁紧档圈GB883-86螺钉锁紧档圈GB884-86带锁圈的螺钉锁紧档圈GB885-86 轴肩档圈GB886-86螺钉紧固轴端档圈GB891-86螺栓紧固轴端档圈GB892-86孔用弹性档圈-A型GB893.1-86 孔用弹性档圈-B型GB893.2-86 轴用弹性档圈-A型GB894.1-86 塑料滚花头螺钉GB840-88开槽球面圆柱头轴位螺钉GB946-88开槽球面大圆柱头螺钉GB947-88开槽沉头不脱出螺钉GB948-88开槽半沉头不脱出螺钉GB949-88内六角花形盘头螺钉GB2672-86内六角花形沉头螺钉GB2673-86内六角花形半沉头螺钉GB2674-86内六角圆柱头轴肩螺钉GB5281-85内六角花形圆柱头螺钉-4.8级GB6190-86轴用弹性档圈-B型GB894.2-86 孔用钢丝档圈GB895.1-86轴用钢丝档圈GB895.2-86开口档圈GB896-86钢丝锁圈GB921-86夹紧档圈GB960-86自攻螺钉十字槽盘头自攻螺钉GB845-85 十字槽沉头自攻螺钉GB846-85 十字槽半沉头自攻螺钉GB847-85 开槽盘头自攻螺钉GB5282-85 内六角花形圆柱头螺钉-8.8和10.9级GB6191-86 精密机械用紧固件十字槽螺钉GB/T13806.1-92十字槽半沉头螺钉GB/T820-2000方头平端紧定螺钉GB821-88十字槽圆柱头螺钉GB/T822-2000十字槽小盘头螺钉GB823-88吊环螺钉GB825-88开槽盘头定位螺钉GB828-88开槽圆柱端定位螺钉GB829-88开槽圆柱头轴位螺钉GB830-88开槽无头轴位螺钉GB831-88开槽带孔球面圆柱头螺钉GB832-88开槽沉头自攻螺钉GB5283-85开槽半沉头自攻螺钉GB5284-85六角头自攻螺钉GB5285-85十字槽盘头自攻锁紧螺钉GB6560-86十字槽沉头自攻锁紧螺钉GB6561-86十字槽半沉头自攻锁紧螺钉GB6562-86六角头自攻锁紧螺钉GB6563-86内六角花形圆柱头自攻锁紧螺钉GB6564-86 十字槽头凹穴六角头自攻螺钉GB9456-88 精密机械用紧固件十字槽自攻螺钉刮削端GB/T13806.2-92墙板自攻螺钉GB/T14210-93 开槽大圆柱头螺钉GB833-88滚花高头螺钉GB834-88滚花平头螺钉GB835-88滚花小头螺钉GB836-88垫圈标准型弹簧垫圈GB93-87平垫圈C级GB/T95-2002大垫圈A级GB/T96.1-2002大垫圈C级GB/T96.2-2002平垫圈A级GB/T97.1-2002平垫圈倒角型A级GB/T97.2-2002十字槽盘头自钻自攻螺钉GB/T15856.1-2002 十字槽沉头自钻自攻螺钉GB/T15856.2-2002 十字槽半沉头自钻自攻螺钉GB/T15856.3-2002 六角法兰面自钻自攻螺钉GB/T15856.4-2002 六角凸缘自钻自攻螺钉GB/T15856.5-2002六角凸缘自攻螺钉GB/T16824.1-1997六角法兰面自攻螺钉GB/T16824.2-1997螺栓方头螺栓C级GB8-88沉头方颈螺栓GB10-88沉头带榫螺拴GB11-88 销轴用平垫圈GB/T97.3-2000平垫圈用于螺钉和垫圈组合件GB/T97.4-2002平垫圈用于自攻螺钉和垫圈组合件GB/T97.5-2002 小垫圈A级GB/T848-2002球面垫圈GB849-88锥面垫圈GB850-88开口垫圈GB851-88工字钢用方斜垫圈GB852-88槽钢用方斜垫圈GB853-88单耳止动垫圈GB854-88双耳止动垫圈GB855-88外舌止动垫圈GB856-88半圆头方颈螺栓GB12-88半圆头带榫螺栓GB13-88大半圆头方颈螺栓C级GB14-1998大半圆头带榫螺栓GB15-88六角头铰制孔用螺栓GB27-88六角头螺杆带孔铰制孔用螺栓GB28-88六角头头部带槽螺栓A和B级GB29.1-88十字槽凹穴六角头螺栓GB29.2-88六角头螺杆带孔螺栓GB31.1-88六角头螺杆带孔螺栓细杆B级GB31.2-88六角头螺杆带孔螺栓细牙A和B级GB31.3-88 六角头头部带孔螺栓A和B级GB32.1-88 圆螺母用止动垫圈GB858-88 轻型弹簧垫圈GB859-87鞍形弹性垫圈GB860-87内齿锁紧垫圈GB861.1-87内锯齿锁紧垫圈GB861.2-87 外齿锁紧垫圈GB862.1-87外锯齿锁紧垫圈GB862.2-87 波形弹性垫圈GB955-87锥形弹性垫圈GB956.1-87锥形锯齿锁紧垫圈GB956.2-87 特大垫圈C级GB/T5287-2002 重型弹簧垫圈GB7244-87六角头头部带孔螺栓细杆B级GB32.2-88六角头头部带孔螺栓细牙A和B级GB32.3-88 下方头螺栓B级GB35-88T形槽用螺栓GB37-88加强半圆头方颈螺栓GB/T794-93活节螺栓GB798-88地脚螺栓GB799-88沉头双榫螺GB800-88小圆半头低方颈螺栓B级GB/T801-1998六角头螺栓C级GB/T5780-2000六角头螺栓全螺纹C级GB/T5781-2000六角头螺栓GB/T5782-2000 鞍形弹簧垫圈GB7245-87波形弹簧垫圈GB7246-87销开口销GB/T91-2000圆锥销GB/T117-2000内螺纹圆锥销GB/T118-2000圆柱销不淬硬钢和奥氏体不锈钢GB/T119.1-2000 圆柱销淬硬钢和马氏体不锈钢GB/T119.2-2000 内螺纹圆柱销不淬硬钢和奥氏体不锈钢GB/T120.1-2000内螺纹圆柱销淬硬钢和马氏体不锈钢六角头螺栓全螺纹GB/T5783-2000六角头螺栓-细杆-B级GB5784-86六角头螺栓细牙GB/T5785-2000六角头螺栓细牙全螺纹GB/T5786-2000六角法兰面螺栓-加大系列-B级GB5789-86六角法兰面螺栓-加大系列-细杆-B级GB5790-86 六角法兰面螺栓小系列GB/T16674-1996钢网架螺栓球节点用高强度螺栓GB/T16939-1997螺柱双头螺柱bm=1dGB897-88双头螺柱bm=1.25dGB898-88 GB/T120.2-2000开尾圆锥销GB877-76螺纹圆柱销GB878-86弹性圆柱销直槽重型GB/T879.1-2000 弹性圆柱销直槽轻型GB/T879.2-2000 弹性圆柱销卷制重型GB/T879.3-2000 弹性圆柱销卷制标准型GB/T879.4-2000 弹性圆柱销卷制轻型GB/T879.5-2000 带孔销GB880-86螺尾锥销GB/T881-2000销轴GB882-86槽销平行沟槽GB/T13829.1-92双头螺柱bm=1.5dGB899-88双头螺柱bm=2dGB900-88等长双头螺柱B级GB901-88手工焊用焊接螺柱GB902.1-89 机动弧焊用焊接螺柱GB902.2-89 储能焊用焊接螺柱GB902.3-89 等长双头螺柱C级GB953-88螺杆GB/T15389-94螺母方螺母C级GB39-88六角螺母C级GB/T41-2000 槽销锥销GB/T13829.2-92槽销圆头沉头GB/T13829.3-92木螺钉开槽圆头木螺钉GB99-86开槽沉头木螺钉GB100-86开槽半沉头木螺钉GB101-86 六角头木螺钉GB102-86十字槽圆头木螺钉GB950-86 十字槽沉头木螺钉GB951-86 十字槽半沉头木螺钉GB952-86六角厚螺母GB56-88蝶形螺母GB62-88环形螺母GB63-88组合式盖形螺母GB802-88球面六角螺母GB804-88扣紧螺母GB805-88滚花高螺母GB806-88滚花薄螺母GB807-88小六角特扁细牙螺母GB808-88 嵌装圆螺母GB809-88小圆螺母GB810-88圆螺母GB812-88 柳钉平头铆钉GB109-86标牌铆钉GB827-86半圆头铆钉GB863.1-86 小半圆头铆钉GB863.2-86 平锥头铆钉GB864-86沉头铆钉GB865-86半沉头铆钉GB866-86半圆头铆钉GB867-86平锥头铆钉GB868-86沉头铆钉GB869-86半沉头铆钉GB870-86端面带孔圆螺母GB815-88侧面带孔圆螺母GB816-88带槽圆螺母GB817-881型非金属嵌件六角锁紧螺母GB/T889.1-20001型非金属嵌件六角锁紧螺母细牙GB/T889.2-2000 盖形螺母GB923-881型六角螺母GB/T6170-20001型六角螺母细牙GB/T6171-2000六角薄螺母GB/T6172.1-2000非金属嵌件六角锁紧薄螺母GB/T6072.2-2000六角薄螺母细牙GB/T6173-2000六角薄螺母无倒角GB/T6174-2000 扁圆头铆钉GB871-86扁平头铆钉GB872-86扁圆头半空心铆钉GB873-86沉头半空心铆钉GB874-86120°扁平头半空心铆钉GB875-86空心铆钉GB876-86沉头铆钉GB954-86120°管状铆钉GB975-86大扁圆头铆钉GB1011-86半沉头铆钉GB1012-86120°平锥头半空心铆钉GB1013-86 大扁圆头半空心铆钉GB1014-862型六角螺母GB/T6175-20002型六角螺母细牙GB/T6176-2000六角法兰面螺母GB/T6177.1-2000六角法兰面螺母细牙GB/T6177.2-20001型六角开槽螺母-A和B级GB6178-861型六角开槽螺母-C级GB6179-862型六角开槽螺母-A和B级GB6180-86六角开槽薄螺母-A和B级GB6181-862型非金属嵌件六角锁紧螺母GB/T6182-2000非金属嵌件六角法兰面锁紧螺母GB/T6183.1-2000 非金属嵌件六角法兰面锁紧螺母细牙GB/T6183.2-2000 沉头半空心铆钉GB1015-86无头铆钉GB1016-86封闭型扁圆头抽芯铆钉GB12615-90封闭型沉头抽芯铆钉GB12616-90开口型沉头抽芯铆钉GB12617-90开口型扁圆头抽芯铆钉GB12618-90扁圆头击芯铆钉GB/T15855.1-1995沉头击芯铆钉GB/T15855.2-1995紧固件-组合件和连接副钢结构用高强度大六角头螺栓GB/T1228-91 钢结构用高强度大六角头螺母GB/T1229-91 钢结构用高强度垫圈GB/T1230-911型全金属六角锁紧螺母GB/T6184-20002型全金属六角锁紧螺母GB/T6185.1-20002型全金属六角锁紧螺母细牙GB/T6185.2-20002型全金属六角锁紧螺母9级GB/T6186-2000全金属六角法兰面锁紧螺母GB/T6187.1-2000全金属六角法兰面锁紧螺母细牙GB/T6187.2-2000 1型六角开槽螺母细牙A和B级GB9457-882型六角开槽螺母细牙A和B级GB9458-88六角开槽薄螺母细牙A和B级GB9459-88焊接方螺母GB/T13680-92焊接六角螺母GB/T13681-92平头铆螺母GB/T17880.1-1999 钢结构用扭剪型高强度螺栓连接副GB/T3632-1995 螺栓或螺钉和平垫圈组合件GB/T9074.1-2002十字槽头螺钉和外锯齿锁紧垫圈组合件GB9074.2-88 十字槽盘头螺钉和弹簧垫圈组合件GB9074.3-88十字槽盘头螺钉、弹簧垫圈和平垫圈组合件GB9074.4-88十字槽小盘头螺钉和平垫圈组合件GB9074.5-88十字槽小盘头螺钉和大垫圈组合件GB9074.6-88十字槽小盘头螺钉和弹簧垫圈组合件GB9074.7-88 十字槽小盘头螺钉、弹簧垫圈和平垫圈组合件GB9074.8-88十字槽沉头螺钉和锥形锁紧垫圈组合件GB9074.9-88 十字槽半沉头螺钉和锥形锁紧垫圈组合件沉头铆螺母GB/T17880.2-1999小沉头铆螺母GB/T17880.3-1999 120°小沉头铆螺母GB/T17880.4-1999 平头六角铆螺母GB/T17880.5-1999精密机械用六角螺母GB/T18195-2000螺钉开槽圆柱头螺钉GB/T65-2000开槽盘头螺钉GB/T67-2000开槽沉头螺钉GB/T68-2000开槽半沉头螺钉GB/T69-2000内六角圆柱头螺钉GB/T70.1-2000 GB9074.10-88十字曹凹穴六角头螺栓和平垫圈组合件GB9074.11-88十字槽凹穴六角头螺栓和弹簧垫圈组合件GB9074.12-88十字槽凹穴六角头螺栓、弹簧垫圈和平垫圈组合件GB9074.13-88六角头螺栓和弹簧垫圈组合件GB9074.15-88六角头螺栓和外锯齿锁紧垫圈组合件GB9074.16-88 六角头螺栓、弹簧垫圈和平垫圈组合件GB9074.17-88 自攻螺钉和平垫圈组合件GB/T9074.18-2002十字槽凹穴六角头自攻螺钉和平垫圈组合件GB9074.20-88内六角平圆头螺钉GB/T70.2-2000 内六角沉头螺钉GB/T70.3-2000开槽锥端紧定螺钉GB71-85开槽锥端定位螺钉GB72-88开槽平端紧定螺钉GB73-85开槽凹端紧定螺钉GB74-85开槽长圆柱端紧定螺钉GB75-85内六角平端紧定螺钉GB/T77-2000 内六角锥端紧定螺钉GB/T78-2000 内六角圆柱端紧定螺钉GB/T79-2000 内六角凹端紧定螺钉GB/T80-2000 方头长圆柱球面端紧定螺钉GB83-88 十字槽凹穴六角头自攻螺钉和大垫圈组合件GB9074.21-88组合件用弹簧垫圈GB9074.26-88组合件用外锯齿锁紧垫圈GB9074.27-88组合件用锥形锁紧垫圈GB9074.28-88腰状杆螺柱连接副型式分类GB/T13807.1-92腰状杆螺柱连接副螺柱GB/T13087.2-92腰状杆螺柱连接副螺母、受力套管GB/T13087.3-92 焊钉电弧螺柱焊用圆柱头焊钉GB/T10433-2002无头焊钉GB10432-89方头凹端紧定螺钉GB84-88方头长圆柱端紧定螺钉GB85-88 方头短圆柱锥端紧定螺钉GB86-88 十字槽盘头螺钉GB/T818-2000六角头不脱出螺钉GB838-88滚花头不脱出螺钉GB839-88美制英制德标对照表——德制弹簧垫圈美制英制德标对照表——自攻螺钉美制英制德标对照表——垫圈美制英制德标对照表——开口销。

序号德国标准中文品名英文品名国际标准中国标准Item DIN-Standard Description in Chinese Description in English ISO-Standard GB-Standard 1DIN1圆锥销taper pins ISO2339GB1172DIN7圆柱销parallel pins ISO2338GB119-86 3DIN84开槽圆柱头螺钉slotted cheese head screws ISO1207GB65-85 4DIN85开槽盘头螺钉slotted pan head screws ISO1580GB67-85 5DIN93单耳止动垫圈tab washers GB8546DIN94开口销split cotter pins ISO1234GB917DIN95开槽半沉头木螺钉slotted raised csk head woodscrewsGB1018DIN96开槽半圆头木螺钉slotted round head wood screws GB999DIN97开槽沉头木螺钉slotted countersunk head woodscrewsGB10010DIN125-A平垫plain washers ISO7089GB97.1-85 11DIN125-B平垫(带倒角）mediun washers ISO7090GB97.2-85 12DIN126平垫plain washers ISO709113DIN127-A重型弹垫spring lock washers,tang ends GB7244 14DIN127-B标准弹垫spring lock washers,square ends GB93-87 15DIN128-A鞍形弹垫single coil spring lock washers GB7245-87 16DIN137-A弹簧止动垫圈curved spring washers17DIN137-B波形弹垫wave spring washers GB955 18DIN186T型方颈螺栓T-head bolts with square neck GB37-88 19DIN188T型双接头螺栓T-head bolts with double nip20DIN258螺纹圆锥销taper pins with threaded end ISO873721DIN261T型头螺栓T-head bolts22DIN315AF蝶型螺母(美制）wing nuts amercia form23DIN315DF蝶型螺母(德制）wing nuts germany form GB62-88 24DIN316AF蝶型螺钉(美制）wing screws amercia form25DIN317DF蝶型螺钉(德制）wing screws germany form德国标准和国际标准、中国标准中英文对照表26DIN319圆球型盖型螺母ball knobs27DIN404开槽带孔球面圆柱头螺钉slotted capstan screws GB832-8828DIN417开槽长圆柱端紧定螺钉slotted set srews with full dogpointISO7435GB75-8529DIN427开槽平端紧定螺钉(半牙）slotted set srews withchamfered endISO2342GB73-8530DIN431小六角特薄细牙螺母pipe nuts with thread GB808-88 31DIN432外舌止动垫圈external tap GB856-88 32DIN433小垫圈(用于圆柱头螺钉）washers for cheese head screws ISO7092GB848-9533DIN434方斜垫圈(U型）square taper washers for U-sectionGB852-8834DIN435方斜垫圈(I型）square taper washers for I-sectionsGB852-8835DIN436方垫圈square washers36DIN438开槽凹端紧定螺钉slotted set with cup point ISO7436GB74-85 37DIN439六角薄螺母hexagon thin nuts ISO4035GB6172-86 38DIN439细牙六角薄螺母hexagon thin nuts ISO8675GB6173-8639DIN440木螺钉专用垫圈rounds washers for woodconstructionsISO709440DIN443密封帽sealing caps,push-in type41DIN444活节螺栓B 型eye bolts form B GB798-88 42DIN462内舌止动垫圈internal tab washers43DIN463双耳止动垫圈washers with two taps GB855-8844DIN464滚花高头螺钉knurled thumb screws withcollarGB834-8845DIN465开槽滚花高头螺钉slotted knurled thumb screws with collar46DIN466滚花高螺母knurled thumb nuts with collar GB806-88 47DIN467滚花薄螺母knurled thumb thin nuts GB807-88 48DIN470锁紧垫圈sealing washers49DIN471轴用弹性挡圈retaining rings forshafts(external),circlipsGB894.1-8650DIN472孔用弹性挡圈retaining rings forbores(internal),circlipsGB893.1-8651DIN478方头带垫螺栓square head bolts with collar52DIN479方头圆柱底端螺栓square head bolts with half dog point53DIN480方头带垫半圆底端螺栓square head bolts with collar,half dog point and54DIN508T型槽螺母T-slot nuts ISO29955DIN525单头螺柱single end studs56DIN529地脚螺栓masonry bolts GB799-88 57DIN546带槽圆螺母slotted round nuts GB817-7658DIN547端面带孔圆螺母round nuts with drilled holesin one faceGB815-8859DIN551开槽平端紧定螺钉slotted sit screws with flatpointISO4776GB73-8560DIN553开槽锥端紧定螺钉slotted set screws with conepointISO7434GB71-8561DIN555六角螺母hexagon nuts ISO403462DIN557方螺母-C square nuts GB39-88 63DIN558六角头螺钉hexagon screws ISO401864DIN561六角头圆柱端紧定螺钉hexagon set screws with full dog point65DIN562薄型方螺母-B square nuts without bevel(pressed nuts)66DIN571六角头木螺钉hexagon head wood screws (coachscrews)GB102-8667DIN580吊环螺钉lifting eye bolts ISO3266GB825-76 68DIN582吊环螺母lifting eye nuts69DIN601六角头螺栓hexagon bolts ISO401670DIN603大半圆头方颈螺栓(马车螺栓）mushroom head square neck bolts(carriage bolts)ISO8677GB14-8871DIN604沉头带插销马车螺栓flat countersunk nib bolts72DIN605沉头长方颈马车螺栓flat countersunk long square neck bolts73DIN607半圆头带插销马车螺栓cup head nib bolts74DIN608沉头短方颈马车螺栓flat countersunk short square neck bolts75DIN609六角头精配螺栓（长螺纹）hexagon fitted bolts,longthread76DIN610六角头精配螺栓（短螺纹）hexagon fitted bolts,shortthread77DIN653滚花平头螺钉knurled thumb screws thin type GB835-88 78DIN660半圆头铆钉round head rivets ISO1051GB867-86 79DIN661沉头铆钉contersunk head rivets ISO1051GB869-86 80DIN662半沉头铆钉raised contersunk head rivets ISO105181DIN674大扁头铆钉mushroom head rivets ISO105182DIN703重型侧面带孔圆螺母adjusting rings,heavy range (shafting collars)83DIN705侧面带孔圆螺母adjusting rings,light range(shafting collars)GB816-8884DIN741卡头wire rope clips85DIN787T型槽螺钉T-slot screws ISO29986DIN835双头螺柱（牙长=2D）studs-metal (end=2d)GB900-8887DIN906内六角锥型闭锁螺钉hexagon socket pipe plugs,conical thread88DIN908内六角直型闭锁螺钉hexagon socket screw plugs,cyl. thread89DIN909外六角锥型闭锁螺钉hexagon head pipe plugs,conical thread90DIN910外六角直型闭锁螺钉hexagon head screw plugs,cyl.thread91DIN911内六角扳手socket wrenches ISO293692DIN912内六角圆柱头螺钉hexagon socket cap screws ISO4762GB70-8593DIN913内六角平端紧定螺钉hexagon socket set screws withflat pointISO4026GB77-8594DIN914内六角尖端紧定螺钉hexagon socket set screws withcone pointISO4027GB78-8595DIN915内六角圆柱端紧定螺钉hexagon socket set screws withdog pointISO4028GB79-8596DIN916内六角凹端紧定螺钉hexagon socket set screws withcup pointISO4029GB80-8597DIN917薄型盲螺母hexagon cap nuts98DIN920开槽小圆柱头螺钉slotted short cheese head screws99DIN921开槽大圆柱头螺钉slotted large cheese headscrewsGB838-88100DIN923开槽圆柱头轴肩螺钉slotted pan head screws withshoulderGB830-88101DIN927开槽无头轴肩螺钉slotted shoulder screws102DIN928焊接方螺母square weld nuts GB/T13680-92 103DIN929焊接六角螺母hexagon weld nuts GB/T13681-92 104DIN931六角头螺栓（半牙）hexagon head screws ISO4014GB5782-86 105DIN933六角头螺栓（全牙）hexagon head screws ISO4017GB5783-86 106DIN934六角头螺母(1型）hexagon full nuts ISO4032GB6170-86 107DIN934细牙六角头螺母(1型）hexagon full nuts ISO8673GB6171-86 108DIN935开槽六角螺母hexagon slotted and castle nuts ISO7035GB6178-86 109DIN936六角头薄螺母hexagon thin nuts ISO4035GB6172.1-86110DIN937六角头开槽薄螺母hexagon thin slotted and castlenutsISO7038GB6181-86111DIN938双头螺距（牙长=1D）studs metal (end=1d)GB897-88 112DIN939双头螺距（牙长=1.25D）studs metal (end=1.25d)GB898-88 113DIN940双头螺距（牙长=1.5D）studs metal (end=1.5d)114DIN960六角头细牙螺栓（半牙）hexagon head bolts,metric finepitch threadISO8765GB5785-86115DIN961六角头细牙螺栓（全牙）hexagon head bolts,metric finepitch threadISO8676GB5786-86116DIN962头部穿孔六角头螺栓additional shapes and versions for bolts117DIN963开槽沉头螺钉slotted countersund head screws ISO 2009GB68-85118DIN964开槽半沉头螺钉slotted raised countersunk ovalhead screwsISO 2010GB69-85119DIN965十字槽沉头螺钉cross recessed countersunk headscrewsISO7046GB819-85120DIN966十字槽半沉头螺钉cross recessed raisedcountersunk head screwsISO7047GB820-85121DIN970六角头螺母hexagon nuts type-1122DIN971六角头螺母hexagon nuts type-2123DIN972细牙六角头螺母(2型）hexagon nuts with fine thread ISO8674GB6176-86 124DIN975牙条(全螺纹）threaded rods(studdings)GB15389-94 125DIN976螺纹销threaded pins(stud bolts)126DIN979六角头开槽薄螺母（２型）hexagon thin slotted and castlenuts127DIN980全金属六角锁紧螺母（１型）prevailling torque type hexagonnuts,all metall nutsISO7199GB6184-86128DIN981圆螺母locknuts ISO2982GB812-88129DIN982六角头尼龙锁紧螺母prevailling torque type hexagonnuts,heavy type ,with nylonISO7040GB889.1-86130DIN985六角头薄型尼龙锁紧螺母prevailling torque type hexagonnuts,heavy type ,with nylonISO10511GB6172.2-86131DIN986六角盖型尼龙锁紧螺母prevailling torque typedomed capnuts with nylon insert132DIN988配合垫片shim rings133DIN1052木材连接用垫片washers for timber connectors 134DIN1151沉头钢钉round plain head nails135DIN1440销钉专用垫片A型plain washers for clevis pins(A型）ISO8738136DIN1441销钉专用垫片plain washers for clevis pins137DIN1444带头销钉clevis pins with head ISO2341138DIN1471圆锥型槽销grooved pins,taper grooved ISO8744GB/T13829.2139DIN1472圆锥型槽销(半槽）grooved pins,taper grooved halflengthISO8745GB/T13829.2140DIN1473平行槽销(带倒角）grooved pins,parallel groovedfull lengthISO8740141DIN1474前端凹槽槽销grooved pins,reserve groovedhalf lengthISO8741142DIN1475中部凹槽槽销grooved pins,centre grooved ISO8742143DIN1476圆头槽销grooved pins with round head ISO8746GB/T13829.3144DIN1477沉头槽销grooved pins with countersunkheadISO8747145DIN1479六角螺母棒turnuckles(centre parts),made out of hexagon bar146DIN1480花篮螺栓turnuckles with eye bolt and hook bolt147DIN1481弹性圆柱销spring pins,heavy type ISO8752GB879-86 148DIN1587组合式盖型螺母hexagon domed cap nuts GB802-88149DIN1804开槽圆螺母（配合沟头扳手）slotted round nuts for hookspanner150DIN1816圆螺母（带插销孔）round nuts with set holes151DIN2093盘型弹簧垫圈disc springs152DIN3017喉箍hose clamps153DIN3404润滑油嘴（旋扭头）lubricating nipples,button head154DIN3567管夹shackles for conduilts155DIN3570U型螺栓stirrup bolts(U-bolts)156DIN6319球面垫圈spherical washers,conical seats GB849-88 157DIN6325圆柱销parallel pins ISO8734158DIN6330厚六角螺母hexagon nuts ,1.5d GB56-88 159DIN6331厚六角法兰面螺母hexagon nuts ,1.5d with collar GB6177-86 160DIN6334长六角螺母hexagon nuts ,3d161DIN6797-A外齿锁紧垫圈external teeth lock washers GB862.1-87 162DIN6797-I内齿锁紧垫圈internal teeth lock washers GB861.1-87163DIN6798-A外锯齿锁紧垫圈external teeth serrated lockwashersGB862.2-87164DIN6798-I内锯齿锁紧垫圈internal teeth serrated lockwashersGB861.2-87165DIN6799 开口挡圈retaining rings for shafts(E-rings),circlipsGB896-76166DIN6885平键（A型）parallel keys(form A )ISO773/2491167DIN6888半圆键woodruff keys ISO3912168DIN6899嵌环（支撑环）thimbles169DIN6900机器螺钉和垫圈组合件screws and washers assemblies GB9074.1-.17170DIN6901自攻螺钉和垫圈组合件tapping screws and washersassembliesGB9074.18-.23171DIN6912薄型带孔内六角圆柱头螺钉hexagon socket head cap screwswith hole,low head172DIN6914大六角头螺栓hexagon head bolts with large head(friction grip bolts)173DIN6915大六角螺母hexagon nuts with large wideth across flat(friction grip nuts)174DIN6916大垫圈round washers for friction grip bolts175DIN6917楔型方垫圈spuare taper washers for friction grip bolts on T-176DIN6923六角法兰面螺母hexagon flange nuts ISO4161GB6177-86177DIN6925全金属六角锁紧螺母(2型）prevailing torque type hexagonnuts,all metallic nutsISO7042GB6185.1-2000178DIN7337开口型抽芯铆钉（沉头、扁圆头）blind rivets GB12617/12618179DIN7338扁平头半空心/全空心铆钉rivets for brake and clutchliningGB875/975-86180DIN7343螺旋夹紧销spiral pins ISO8750 181DIN7346轻型弹性圆柱销spring pins,light type ISO13337182DIN7349重型弹性圆柱销用垫圈washers for bolts with heavy type spring pinss183DIN7500ISO公制螺纹螺钉(多种头型）threadforming screws for ISO-metric thread184DIN7504自攻自钻螺钉(多种头型）self-drilling tapping screws185DIN7513开槽切削螺纹螺钉(多种头型）thread cutting screws186DIN7516十字槽切削螺纹螺钉(多种头型）thread cutting screws crossrecess187DIN7965T型四爪螺母tee nuts with pronge188DIN7968钢结构用六角头螺栓连接副hexagon head fitted bolts forsteel structuresGB1228/1229/1230189DIN7971开槽盘头自攻螺钉pan head tapping screws withslotISO1481GB5282-85190DIN7972开槽沉头自攻螺钉countersunk flat head tappingscrews with slotISO1482GB5283-85191DIN7973开槽半沉头自攻螺钉raised countersunk oval headtapping screws with slotISO1483GB5284-85192DIN7976六角头自攻螺钉hexagon tapping screws ISO1479GB5285-85193DIN7980圆柱头螺钉用弹簧垫圈spring lock washers for screwswith cylindrical headsISO8738194DIN7981十字槽盘头自攻螺钉pan head tapping screws withcross recessedISO 7049GB845-85195DIN7982十字槽沉头自攻螺钉countersunk flat head tappingscrews with cross recessedISO7050GB846-85196DIN7983十字槽半沉头自攻螺钉raised countersunk oval headtapping screws with crossISO7051GB847-86197DIN7984薄型内六角圆柱头螺钉hexagon socket head cap screws with，reduced head198DIN7985十字槽盘头螺钉pan head screws with crossrecessedISO7045GB818-85199DIN7989钢结构用垫圈washers for steel structures GB1230-84200DIN7990钢结构用六角头螺栓hexagon head bolts for steelstructuresGB1229-84201DIN7991内六角沉头螺钉hexagon socket countersunk headscrewsISO10642202DIN7993轴用钢丝挡圈roundwire snap rings for shafts GB895.2-86203DIN7995十字槽半沉头木螺钉cross recessed raisedcountersunk head wood screwsGB952-86204DIN7996十字槽圆头木螺钉cross recessed round head woodscrewsGB950-86205DIN7997十字槽沉头木螺钉cross recessed countersunk headwood screwsGB951-86206DIN8140螺纹护套（普通\自锁等）ciol inserts,coarse,finethread,silf locking207DIN9021大外径垫圈washers,outside diameterappro.3dISO7093GB96.1-85208DIN11024弹簧卡子spring cotter for a bolt209DIN13257平板螺栓belting bolts (elevator bolts)210DIN18182干壁钉（墙板钉）dry wall screws211DIN28129环型螺母lifting nuts(eye nuts)GB63-88212DIN70952圆螺母用止退垫圈tab washers for slotted roundnutsGB858-88尺寸核对OKOKOKOKGB粗din75°GB90°OKDIN对边大１DIN对边大１din槽深din薄GB m1.6～m10 DIN m1~m20din厚内径小DIN薄外径大GB头圆弧小OK。

德标、欧标、国际、国标对照表—— DIN EN ISO GB 对照表新德标旧德标 英文名 中文名 国标 DIN EN ISO 4014DIN 931-1 Hexagon head bolts - Product grades A and B(ISO 4014:1999) 六角头螺栓 GB/T 5782-2000 DIN EN ISO 4016DIN 601 Hexagon head bolts - Product grade C(ISO 4016:1999) 六角头螺栓 C 级 GB/T 5780-2000 DIN EN ISO 4017DIN 933 Hexagon head screws - Product grade A and B (ISO 4017:1999) 六角头螺栓 全螺纹 GB/T 5783-2000 DIN EN ISO 4018DIN 558 Hexagon head screws - Product grade C (ISO 4018:1999) 六角头螺栓 全螺纹 C 级 GB/T 5781-2000 DIN EN ISO 8676DIN 961 Hexagon head screws with metric fine pitch thread - Product grade A and B(ISO 8676:1999) 六角头螺栓 细牙 全螺纹 GB/T 5786-2000 DIN EN ISO 8765DIN 960 Hexagon head bolts with fine pitch thread - Product grades A and B(ISO 8765:1999) 六角头螺栓 细牙 GB/T 5785-2000 DIN EN ISO 4032DIN 934 Hexagon nuts,style 1-Product grades A and B(ISO: 4032:1999) 1型六角螺母 GB/T 6170-2000 DIN EN ISO 4033Hexagon nuts,style 2-Product grades A and B(ISO: 4033:1999) 2型六角螺母 GB/T 6175-2000 DIN EN ISO 4034DIN 555 Hexagon nuts - Product grade C (ISO 4034:1999) 六角螺母 C 级 GB/T 41-2000 DIN EN ISO 4035DIN 439-2 Hexagon thin nuts(chamfered)-Product grade A and B (ISO 4035:1999) 六角薄螺母 GB/T 6172.1-2000 DIN EN ISO 4036DIN 439-1 Hexagon thin nuts - Product grade B(unchamfered)(ISO 4036:1999) 六角薄螺母 无倒角 GB/T 6174-2000 DIN EN ISO 8673DIN 934| DIN 971-1 Hexagon nuts,style 1,with metric fine pitch thread - Product grades A and B (ISO 8673:1999) 1型六角螺母 细牙 GB/T 6171-2000 DIN EN ISO 8674DIN 971-2 Hexagon nuts,style 2,with metric fine pitch thread - Product grades A and B (ISO 8674:1999) 2型六角螺母 细牙 GB/T 6176-2000 DIN EN ISO 8675DIN 439-2 Hexagon thin nuts with metric fine pitch thread - Product grades A and B (ISO 8675:1999) 六角薄螺母 细牙 GB/T 6173-2000 DIN EN ISO 4762 DIN 912 Hexagon socket head cap screws(ISO 4762:1997) 内六角圆柱头螺钉GB/T 70.1-2000DIN EN ISO 7380Hexagon socket button head sxrews (ISO 7380:1997) 内六角平圆头螺钉 GB/T 70.2-2000 DIN EN ISO 10642DIN 7991 Hexagon socket countersunk head screws (ISO 10642:1997) 内六角沉头螺钉 GB/T 70.3-2000 DIN EN ISO 1207DIN 84 Slotted cheese head screws-Product grade A(ISO 1207:1992) 开槽圆柱头螺钉 GB/T 65-2000 DIN EN ISO 1580DIN 85 Slotted pan head screws-Product grade A(ISO 1580:1994) 开槽盘头螺钉 GB/T 67-2000 DIN EN ISO 2009DIN 963 Slotted countersunk flat head screws(common head style)(ISO 2009:1994) 开槽沉头螺钉 GB/T 68-2000 DIN EN ISO 2010DIN 964 Countersunk slotted raised head screws(common head style)-Produce grade A(ISO 2010:1994) 开槽半沉头螺钉 GB/T 69-2000 DIN EN ISO 7045DIN 7985 Pan head screws with type H or type Z cross recess-Product grade A(ISO 7054:1994) 十字槽盘头螺钉 GB/T 818-2000 DIN EN ISO 7046-1DIN 965 Countersunk flat head screws (common head style)with type H or type Z cross recess,product grade A-Part 1:Steel of property class 4.8(ISO 7046-1:1994) 十字槽盘头螺钉 第1部分：钢4.8级 GB/T 819.1-2000 DIN EN ISO 7046-2DIN 965 Cross recessed countersunk flat head screws (common head style),product grade A-Part2:Steel of property class 8.8,stainless steel and nonferous metals(ISO 7046-2:1990) 十字槽沉头螺钉 第2部分：钢8.8、不锈钢A2-70和有色金属CU2或CU3 GB/T 819.2-1997 DIN EN ISO 7047DIN 966 Countersunk raised head screws (common head style) with type H or type Z cross recess-Product grade A(ISO 7047:1994) 十字槽半沉头螺钉 GB/T 820-2000 DIN EN ISO 7048Cross recessed cheese head screws (ISO 7048:1998) 十字槽圆柱头螺钉 GB/T 822-2000 DIN EN ISO 10644Screw and washer assemblies with plain washers-Washer hardness classes 200HV and 300HV(ISO 10644:1998) 螺栓或螺钉和平垫圈组合件 GB/T 9074.1-2002 DIN EN ISO 10510Tapping screw and washer assemblies with plain washers(ISO 10510l:1999) 自攻螺钉和平垫圈组合件 GB/T 9074.18-2002 IDN EN ISO 15480Hexagon washer head drilling screws with tapping screws thread (ISO 15480:1999) 六角凸缘自钻自攻螺钉 GB/T 15856.5-2002 IDN EN ISO 15481Cross recessed pan head drilling screws with tapping screw thread(ISO 15481:1999) 十字槽盘头自钻自攻螺钉 GB/T 15856.1-2002 IDN EN ISO 15482 Cross recessed countersunk head drilling screws with tapping screw thread (ISO 15482:1999) 十字槽沉头自钻自攻螺钉GB/T 15856.2-2002IDN EN ISO 15483Cross recessed raised countersunk head drilling screws with tapping screw thread(ISO 15483:1999) 十字槽半沉头自钻自攻螺钉 GB/T 15856.3-2002 DIN EN ISO 10669Plain washers for tapping screw and washer assemblies - Normal and large series - Product grade A （ISO 10669:1999) 平垫圈 用于自攻螺钉和垫圈组合件 GB/T 97.5-2002 DIN EN ISO 10673Plain washers for screw and washer assemblies - Small,normal and large series - Product grade A (ISO 10673:1998) 平垫圈 用于螺钉和垫圈组合件 GB/T 97.4-2002 DIN EN ISO 2338DIN 7 Parallel pins,of unhardened steel and austenitic stainless steel(ISO 2338:1997) 圆柱销 不淬硬钢和奥氏体不锈钢 GB/T 119.1-2000 DIN EN ISO 8733DIN 7979 Parallel pins whit internal thread,of unhardened steel and austenitic stainless steel(ISO 8733:1997) 内螺纹圆柱销 不淬硬钢和奥氏体不锈钢 GB/T 120.1-2000 DIN EN ISO 8734DIN 6325 Parallel pins,of hardened steel or martensitic stainless steel(Dowel pins)(ISO 8734:1997) 圆柱销 淬硬钢和马氏体不锈钢 GB/T 119.2-2000 DIN EN ISO 8735DIN 7979 Parallel pins with internal thread,of hardened steel and martensitic stainless steel(ISO 8735:1997) 内螺纹圆柱销 淬硬钢和马氏体不锈钢 GB/T 120.2-2000 DIN EN ISO 8748DIN 7344 Spring-type straight pins,coiled,heavy duty (ISO 8748:1997) 弹性圆柱销 卷制 重型 GB/T 879.3-2000 DIN EN ISO 8750DIN 7343 Spring-type straight pins,coiled,standard duty (ISO 8750:1997) 弹性圆柱销 卷制 标准型 GB/T 879.4-2000 DIN EN ISO 8751Spring-type straight pins,coiled,light duty （ISO 8751:1997) 弹性圆柱销 卷制 轻型 GB/T 879.5-2000 DIN EN ISO 8752DIN 1481 Spring-type straight pins,slotted,heavy duty (ISO 8752:1997) 弹性圆柱销 直槽 重型 GB/T 879.1-2000 DIN EN ISO 13337DIN 7346 Spring-type straight pins,slotted,light duty (ISO 13337:1997) 弹性圆柱销 直槽 轻型 GB/T 879.2-2000 DIN EN ISO 1234DIN 94 Split pins （ISO1234:1997) 开口销 GB/T 91-2000 DIN EN ISO 7089Plain washers-Normal series-Product grade A 平垫圈 A 级 GB/T 97.1-2002 DIN EN ISO 7090Plain washers,chamfered-Normal series-Product grade A(ISO 7090:2000) 平垫圈 倒角型 A 级 GB/T 97.2-2002 DIN EN ISO 7091Plain washers-Normal series-Product grade C(ISO 7091:2000) 平垫圈 C 级 GB/T 95-2002 DIN EN ISO 7092 Plain washers-Small series-Product grade A(ISO 7092:2000)小垫圈 A 级 GB/T 848-2002DIN EN ISO 7093-1 Plain washers-Large series-Part 1: Product grade A(ISO 70931-1:2000)大垫圈 A 级 GB/T 96.1-2002DIN EN ISO 7093-2Plain washers-Normal series-Part 3: Product grade C(ISO 70936-2:2000) 大垫圈 C 级 GB/T 96.2-2002 DIN EN ISO 7094Plain washers-Extra large series -Product grade C(ISO 7094:2000) 特大垫圈 C 级 GB/T 5287-2002 DIN EN ISO 7040DIN 982| DIN 6924 Prevailing torque type hexagon nuts (with non-metallic insert),style 1 - Property classes 5,8 and 10(ISO 7040:1997) 1型非金属嵌件六角锁紧螺母 GB/T 889.1-2000 DIN EN ISO 7042DIN 980| DIN 6925 Prevailing torque type all-metal hexagon nuts,style 2 - Property classes 5,8, 10 and 12(ISO 7042:1997) 2型全金属六角锁紧螺母 GB/T 6185.1-2000 DIN EN ISO 7719Prevailing torque type all-metal hexagon nuts,style 1- Property classes 5,8 and 10(ISO 7719:1997) 1型全金属六角锁紧螺母 GB/T 6184-2000 DIN EN ISO 10511DIN 985 Prevailing torque type hexagon thin nuts (with non-metallic insert )(ISO 10511:1997) 非金属嵌件六角锁紧薄螺母 GB/T 6072.2-2000 DIN EN ISO 10512DIN 982| DIN 6924 Prevailing torque type hexagon nuts (with non-metallic insert),style 1,with metric fine pitch thread-Property classes 6,8 and 10(ISO 10512:1997) 1型非金属嵌件六角锁紧螺母 细牙 GB/T 889.2-2000 DIN EN ISO 10513 DIN 980|DIN 6925 Prevailing torque type all-metal hexagon nuts,style 2,with metric fine pitch thread - Property classes 8,10 and 12(ISO 10513:1997)2型全金属六角锁紧螺母 细牙GB/T 6185.2-2000。

紧固件规格标准——GB标准档圈锥销锁紧档圈 GB 883-86螺钉锁紧档圈 GB 884-86带锁圈的螺钉锁紧档圈 GB 885-86 轴肩档圈 GB 886-86螺钉紧固轴端档圈 GB 891-86螺栓紧固轴端档圈 GB 892-86孔用弹性档圈-A型 GB 893.1-86 孔用弹性档圈-B型 GB 893.2-86 轴用弹性档圈-A型 GB 894.1-86 轴用弹性档圈-B型 GB 894.2-86 孔用钢丝档圈 GB 895.1-86轴用钢丝档圈 GB 895.2-86开口档圈 GB 896-86钢丝锁圈 GB 921-86夹紧档圈 GB 960-86 塑料滚花头螺钉 GB 840-88开槽球面圆柱头轴位螺钉 GB 946-88开槽球面大圆柱头螺钉 GB 947-88开槽沉头不脱出螺钉 GB 948-88开槽半沉头不脱出螺钉 GB 949-88内六角花形盘头螺钉 GB 2672-86内六角花形沉头螺钉 GB 2673-86内六角花形半沉头螺钉 GB 2674-86内六角圆柱头轴肩螺钉 GB 5281-85内六角花形圆柱头螺钉-4.8级 GB 6190-86内六角花形圆柱头螺钉-8.8和10.9级 GB 6191-86 精密机械用紧固件十字槽螺钉 GB /T 13806.1-92 十字槽半沉头螺钉 GB /T 820-2000方头平端紧定螺钉 GB 821-88十字槽圆柱头螺钉 GB /T 822-2000十字槽小盘头螺钉 GB 823-88吊环螺钉 GB 825-88自攻螺钉十字槽盘头自攻螺钉 GB 845-85十字槽沉头自攻螺钉 GB 846-85十字槽半沉头自攻螺钉 GB 847-85开槽盘头自攻螺钉 GB 5282-85开槽沉头自攻螺钉 GB 5283-85开槽半沉头自攻螺钉 GB 5284-85六角头自攻螺钉 GB 5285-85十字槽盘头自攻锁紧螺钉 GB 6560-86十字槽沉头自攻锁紧螺钉 GB 6561-86十字槽半沉头自攻锁紧螺钉 GB 6562-86六角头自攻锁紧螺钉 GB 6563-86内六角花形圆柱头自攻锁紧螺钉 GB 6564-86十字槽头凹穴六角头自攻螺钉 GB 9456-88精密机械用紧固件十字槽自攻螺钉刮削端 GB /T 13806.2-92 墙板自攻螺钉 GB /T 14210-93十字槽盘头自钻自攻螺钉 GB /T 15856.1-2002十字槽沉头自钻自攻螺钉 GB /T 15856.2-2002十字槽半沉头自钻自攻螺钉 GB /T 15856.3-2002 开槽盘头定位螺钉 GB 828-88开槽圆柱端定位螺钉 GB 829-88开槽圆柱头轴位螺钉 GB 830-88开槽无头轴位螺钉 GB 831-88开槽带孔球面圆柱头螺钉 GB 832-88开槽大圆柱头螺钉 GB 833-88滚花高头螺钉 GB 834-88滚花平头螺钉 GB 835-88滚花小头螺钉 GB 836-88垫圈标准型弹簧垫圈 GB 93-87平垫圈 C级 GB /T 95-2002大垫圈 A级 GB /T 96.1-2002大垫圈 C级 GB /T 96.2-2002平垫圈 A级 GB /T 97.1-2002平垫圈倒角型 A级 GB /T 97.2-2002销轴用平垫圈 GB /T 97.3-2000平垫圈用于螺钉和垫圈组合件 GB /T 97.4-2002六角法兰面自钻自攻螺钉 GB /T 15856.4-2002 六角凸缘自钻自攻螺钉 GB /T 15856.5-2002 六角凸缘自攻螺钉 GB /T 16824.1-1997六角法兰面自攻螺钉 GB /T 16824.2-1997螺栓方头螺栓 C级 GB 8-88沉头方颈螺栓 GB 10-88沉头带榫螺拴 GB 11-88半圆头方颈螺栓 GB 12-88半圆头带榫螺栓 GB 13-88大半圆头方颈螺栓 C级 GB 14-1998大半圆头带榫螺栓 GB 15-88六角头铰制孔用螺栓 GB 27-88六角头螺杆带孔铰制孔用螺栓 GB 28-88六角头头部带槽螺栓 A 和 B 级 GB 29.1-88 十字槽凹穴六角头螺栓 GB 29.2-88六角头螺杆带孔螺栓 GB 31.1-88六角头螺杆带孔螺栓细杆 B级 GB 31.2-88 平垫圈用于自攻螺钉和垫圈组合件 GB /T 97.5-2002 小垫圈 A级 GB /T 848-2002球面垫圈 GB 849-88锥面垫圈 GB 850-88开口垫圈 GB 851-88工字钢用方斜垫圈 GB 852-88槽钢用方斜垫圈 GB 853-88单耳止动垫圈 GB 854-88双耳止动垫圈 GB 855-88外舌止动垫圈 GB 856-88圆螺母用止动垫圈 GB 858-88轻型弹簧垫圈 GB 859-87鞍形弹性垫圈 GB 860-87内齿锁紧垫圈 GB 861.1-87内锯齿锁紧垫圈 GB 861.2-87外齿锁紧垫圈 GB 862.1-87外锯齿锁紧垫圈 GB 862.2-87波形弹性垫圈 GB 955-87锥形弹性垫圈 GB 956.1-87六角头螺杆带孔螺栓细牙 A和B级 GB 31.3-88 六角头头部带孔螺栓 A 和 B级 GB 32.1-88六角头头部带孔螺栓细杆 B级 GB 32.2-88六角头头部带孔螺栓细牙 A 和 B 级 GB 32.3-88 下方头螺栓 B级 GB 35-88T 形槽用螺栓 GB 37-88加强半圆头方颈螺栓 GB /T794-93活节螺栓 GB 798-88地脚螺栓 GB 799-88沉头双榫螺 GB 800-88小圆半头低方颈螺栓 B级 GB /T 801-1998六角头螺栓 C级 GB /T 5780-2000六角头螺栓全螺纹 C级 GB /T 5781-2000六角头螺栓 GB /T 5782-2000六角头螺栓全螺纹 GB /T 5783-2000六角头螺栓-细杆-B级 GB 5784-86六角头螺栓细牙 GB /T 5785-2000六角头螺栓细牙全螺纹 GB /T 5786-2000六角法兰面螺栓-加大系列-B级 GB 5789-86 锥形锯齿锁紧垫圈 GB 956.2-87特大垫圈 C级 GB /T 5287-2002重型弹簧垫圈 GB 7244-87鞍形弹簧垫圈 GB 7245-87波形弹簧垫圈 GB 7246-87销开口销 GB /T 91-2000圆锥销 GB /T 117-2000内螺纹圆锥销 GB /T 118-2000圆柱销不淬硬钢和奥氏体不锈钢 GB /T 119.1-2000圆柱销淬硬钢和马氏体不锈钢 GB /T 119.2-2000内螺纹圆柱销不淬硬钢和奥氏体不锈钢 GB /T 120.1-2000 内螺纹圆柱销淬硬钢和马氏体不锈钢 GB /T 120.2-2000 开尾圆锥销 GB 877-76螺纹圆柱销 GB 878-86弹性圆柱销直槽重型 GB /T 879.1-2000弹性圆柱销直槽轻型 GB /T 879.2-2000弹性圆柱销卷制重型 GB /T 879.3-2000六角法兰面螺栓-加大系列-细杆-B级 GB 5790-86 六角法兰面螺栓小系列 GB /T 16674-1996钢网架螺栓球节点用高强度螺栓 GB /T 16939-1997螺柱双头螺柱 bm=1d GB 897-88双头螺柱 bm=1.25d GB 898-88双头螺柱 bm=1.5d GB 899-88双头螺柱 bm=2d GB 900-88等长双头螺柱 B级 GB 901-88手工焊用焊接螺柱 GB 902.1-89机动弧焊用焊接螺柱 GB 902.2-89储能焊用焊接螺柱 GB 902.3-89等长双头螺柱 C级 GB 953-88螺杆 GB /T 15389-94螺母方螺母 C级 GB 39-88六角螺母 C级 GB /T41-2000 弹性圆柱销卷制标准型 GB /T 879.4-2000 弹性圆柱销卷制轻型 GB /T 879.5-2000 带孔销 GB 880-86螺尾锥销 GB /T 881-2000销轴 GB 882-86槽销平行沟槽 GB /T 13829.1-92槽销锥销 GB /T 13829.2-92槽销圆头沉头 GB /T 13829.3-92木螺钉开槽圆头木螺钉 GB 99-86开槽沉头木螺钉 GB 100-86开槽半沉头木螺钉 GB 101-86六角头木螺钉 GB 102-86十字槽圆头木螺钉 GB 950-86十字槽沉头木螺钉 GB 951-86十字槽半沉头木螺钉 GB 952-86柳钉六角厚螺母 GB 56-88蝶形螺母 GB 62-88环形螺母 GB 63-88组合式盖形螺母 GB 802-88球面六角螺母 GB 804-88扣紧螺母 GB 805-88滚花高螺母 GB 806-88滚花薄螺母 GB 807-88小六角特扁细牙螺母 GB 808-88嵌装圆螺母 GB 809-88小圆螺母 GB 810-88圆螺母 GB 812-88端面带孔圆螺母 GB 815-88侧面带孔圆螺母 GB 816-88带槽圆螺母 GB 817-881型非金属嵌件六角锁紧螺母 GB /T 889.1-20001型非金属嵌件六角锁紧螺母细牙 GB /T 889.2-2000 盖形螺母 GB 923-881型六角螺母 GB /T 6170-2000 平头铆钉 GB 109-86标牌铆钉 GB 827-86半圆头铆钉 GB 863.1-86小半圆头铆钉 GB 863.2-86平锥头铆钉 GB 864-86沉头铆钉 GB 865-86半沉头铆钉 GB 866-86半圆头铆钉 GB 867-86平锥头铆钉 GB 868-86沉头铆钉 GB 869-86半沉头铆钉 GB 870-86扁圆头铆钉 GB 871-86扁平头铆钉 GB 872-86扁圆头半空心铆钉 GB 873-86 沉头半空心铆钉 GB 874-86 120°扁平头半空心铆钉 GB 875-86 空心铆钉 GB 876-86沉头铆钉 GB 954-86 120°管状铆钉 GB 975-861型六角螺母细牙 GB /T 6171-2000六角薄螺母 GB /T 6172.1-2000非金属嵌件六角锁紧薄螺母 GB /T 6072.2-2000六角薄螺母细牙 GB /T 6173-2000六角薄螺母无倒角 GB /T 6174-20002型六角螺母 GB /T 6175-20002型六角螺母细牙 GB /T 6176-2000六角法兰面螺母 GB /T 6177.1-2000六角法兰面螺母细牙 GB /T 6177.2-20001型六角开槽螺母-A和B级 GB 6178-861型六角开槽螺母-C级 GB 6179-862型六角开槽螺母-A和B级 GB 6180-86六角开槽薄螺母-A和B级 GB 6181-862型非金属嵌件六角锁紧螺母 GB /T 6182-2000非金属嵌件六角法兰面锁紧螺母 GB /T 6183.1-2000非金属嵌件六角法兰面锁紧螺母细牙 GB /T 6183.2-2000 1型全金属六角锁紧螺母 GB /T 6184-20002型全金属六角锁紧螺母 GB /T 6185.1-20002型全金属六角锁紧螺母细牙 GB /T 6185.2-2000 大扁圆头铆钉 GB 1011-86半沉头铆钉 GB 1012-86 120°平锥头半空心铆钉 GB 1013-86大扁圆头半空心铆钉 GB 1014-86沉头半空心铆钉 GB 1015-86无头铆钉 GB 1016-86封闭型扁圆头抽芯铆钉 GB 12615-90封闭型沉头抽芯铆钉 GB 12616-90开口型沉头抽芯铆钉 GB 12617-90开口型扁圆头抽芯铆钉 GB 12618-90扁圆头击芯铆钉 GB /T 15855.1-1995沉头击芯铆钉 GB /T 15855.2-1995紧固件-组合件和连接副钢结构用高强度大六角头螺栓 GB /T 1228-91钢结构用高强度大六角头螺母 GB /T 1229-91钢结构用高强度垫圈 GB /T 1230-91钢结构用扭剪型高强度螺栓连接副 GB /T 3632-1995 螺栓或螺钉和平垫圈组合件 GB /T 9074.1-2002十字槽头螺钉和外锯齿锁紧垫圈组合件 GB 9074.2-882型全金属六角锁紧螺母 9级 GB /T 6186-2000全金属六角法兰面锁紧螺母 GB /T 6187.1-2000全金属六角法兰面锁紧螺母细牙 GB /T 6187.2-2000 1型六角开槽螺母细牙 A和B级 GB 9457-882型六角开槽螺母细牙 A和B级 GB 9458-88六角开槽薄螺母细牙 A和B级 GB 9459-88焊接方螺母 GB /T 13680-92焊接六角螺母 GB /T 13681-92平头铆螺母 GB /T 17880.1-1999沉头铆螺母 GB /T 17880.2-1999小沉头铆螺母 GB /T 17880.3-1999120°小沉头铆螺母 GB /T 17880.4-1999平头六角铆螺母 GB /T 17880.5-1999精密机械用六角螺母 GB /T 18195-2000螺钉开槽圆柱头螺钉 GB /T 65-2000开槽盘头螺钉 GB /T 67-2000开槽沉头螺钉 GB /T 68-2000 十字槽盘头螺钉和弹簧垫圈组合件 GB 9074.3-88十字槽盘头螺钉、弹簧垫圈和平垫圈组合件 GB 9074.4-88十字槽小盘头螺钉和平垫圈组合件 GB 9074.5-88十字槽小盘头螺钉和大垫圈组合件 GB 9074.6-88十字槽小盘头螺钉和弹簧垫圈组合件 GB 9074.7-88十字槽小盘头螺钉、弹簧垫圈和平垫圈组合件 GB 9074.8-88十字槽沉头螺钉和锥形锁紧垫圈组合件 GB 9074.9-88十字槽半沉头螺钉和锥形锁紧垫圈组合件 GB 9074.10-88十字曹凹穴六角头螺栓和平垫圈组合件 GB 9074.11-88十字槽凹穴六角头螺栓和弹簧垫圈组合件 GB 9074.12-88十字槽凹穴六角头螺栓、弹簧垫圈和平垫圈组合件 GB 9074.13-88 六角头螺栓和弹簧垫圈组合件 GB 9074.15-88六角头螺栓和外锯齿锁紧垫圈组合件 GB 9074.16-88六角头螺栓、弹簧垫圈和平垫圈组合件 GB 9074.17-88自攻螺钉和平垫圈组合件 GB /T 9074.18-2002十字槽凹穴六角头自攻螺钉和平垫圈组合件 GB 9074.20-88十字槽凹穴六角头自攻螺钉和大垫圈组合件 GB 9074.21-88组合件用弹簧垫圈 GB 9074.26-88组合件用外锯齿锁紧垫圈 GB 9074.27-88开槽半沉头螺钉 GB /T 69-2000内六角圆柱头螺钉 GB /T 70.1-2000 内六角平圆头螺钉 GB /T 70.2-2000 内六角沉头螺钉 GB /T 70.3-2000开槽锥端紧定螺钉 GB 71-85开槽锥端定位螺钉 GB 72-88开槽平端紧定螺钉 GB 73-85开槽凹端紧定螺钉 GB 74-85开槽长圆柱端紧定螺钉 GB 75-85内六角平端紧定螺钉 GB /T 77-2000 内六角锥端紧定螺钉 GB /T 78-2000 内六角圆柱端紧定螺钉 GB /T 79-2000 内六角凹端紧定螺钉 GB /T 80-2000 方头长圆柱球面端紧定螺钉 GB 83-88 方头凹端紧定螺钉 GB 84-88方头长圆柱端紧定螺钉 GB 85-88方头短圆柱锥端紧定螺钉 GB 86-88十字槽盘头螺钉 GB /T 818-2000六角头不脱出螺钉 GB 838-88 组合件用锥形锁紧垫圈 GB 9074.28-88腰状杆螺柱连接副型式分类 GB /T 13807.1-92腰状杆螺柱连接副螺柱 GB /T 13087.2-92腰状杆螺柱连接副螺母、受力套管 GB /T 13087.3-92焊钉电弧螺柱焊用圆柱头焊钉 GB /T 10433-2002无头焊钉 GB 10432-89滚花头不脱出螺钉 GB 839-88美制英制德标对照表——德制弹簧垫圈美制英制德标对照表——自攻螺钉美制英制德标对照表——垫圈美制英制德标对照表——开口销。

紧固件国标对照
紧固件（Fasteners）是机械工程中常用的一种小型元件，广泛应用于机械结构中。

由于紧固件的种类繁多，并且不同国家和地区有不同的使用标准，因此我们需要了解各个国家和地区的紧固件国标，以便正确使用和选择紧固件。

下面是中文的一些常见的紧固件国标对照表。

1. DIN（德国标准）
代码名称 GB（中国标准）
DIN6912 长轴头内六角螺栓 GB/T8992
DIN931 全螺纹六角头螺栓 GB/T5780
DIN933 长六角全螺纹螺栓 GB/T5781
DIN934 六角螺母 GB/T6170
DIN985 锁紧螺母 GB/T105-2003
DIN125A 平垫圈A型 GB/T97，GB/T848
DIN127B 弹性垫圈B型 GB/T93
3. ASTM（美国标准）
4. JIS（日本标准）
代码名称
GB/T67.1-2003 六角粗牙螺栓
GB/T5780 全螺纹六角头螺栓
GB/T5781 长六角全螺纹螺栓
GB/T6170 六角螺母
GB/T6175.3-2003 镀层紧固件的防腐蚀试验方法。

紧固件GB大全以及美制英制德标对照表紧固件规格标准——GB标准档圈锥销锁紧档圈 GB 883-86螺钉锁紧档圈 GB 884-86带锁圈的螺钉锁紧档圈 GB 885-86轴肩档圈 GB 886-86螺钉紧固轴端档圈 GB 891-86螺栓紧固轴端档圈 GB 892-86孔用弹性档圈-A型 GB 893.1-86孔用弹性档圈-B型 GB 893.2-86轴用弹性档圈-A型 GB 894.1-86轴用弹性档圈-B型 GB 894.2-86孔用钢丝档圈 GB 895.1-86轴用钢丝档圈 GB 895.2-86开口档圈 GB 896-86钢丝锁圈 GB 921-86夹紧档圈 GB 960-86自攻螺钉十字槽盘头自攻螺钉 GB 845-85十字槽沉头自攻螺钉 GB 846-85十字槽半沉头自攻螺钉 GB 847-85开槽盘头自攻螺钉 GB 5282-85开槽沉头自攻螺钉 GB 5283-85开槽半沉头自攻螺钉 GB 5284-85六角头自攻螺钉 GB 5285-85十字槽盘头自攻锁紧螺钉 GB 6560-86 塑料滚花头螺钉 GB 840-88开槽球面圆柱头轴位螺钉 GB 946-88开槽球面大圆柱头螺钉 GB 947-88开槽沉头不脱出螺钉 GB 948-88开槽半沉头不脱出螺钉 GB 949-88内六角花形盘头螺钉 GB 2672-86内六角花形沉头螺钉 GB 2673-86内六角花形半沉头螺钉 GB 2674-86内六角圆柱头轴肩螺钉 GB 5281-85内六角花形圆柱头螺钉-4.8级 GB 6190-86内六角花形圆柱头螺钉-8.8和10.9级 GB 6191-86 精密机械用紧固件十字槽螺钉GB /T 13806.1-92 十字槽半沉头螺钉GB /T 820-2000方头平端紧定螺钉 GB 821-88十字槽圆柱头螺钉 GB /T 822-2000十字槽小盘头螺钉 GB 823-88吊环螺钉 GB 825-88开槽盘头定位螺钉 GB 828-88开槽圆柱端定位螺钉 GB 829-88开槽圆柱头轴位螺钉 GB 830-88开槽无头轴位螺钉 GB 831-88开槽带孔球面圆柱头螺钉 GB 832-88开槽大圆柱头螺钉 GB 833-88滚花高头螺钉 GB 834-88滚花平头螺钉 GB 835-88滚花小头螺钉 GB 836-88十字槽沉头自攻锁紧螺钉 GB 6561-86十字槽半沉头自攻锁紧螺钉 GB 6562-86六角头自攻锁紧螺钉 GB 6563-86内六角花形圆柱头自攻锁紧螺钉 GB 6564-86十字槽头凹穴六角头自攻螺钉 GB 9456-88精密机械用紧固件十字槽自攻螺钉刮削端 GB /T 13806.2-92 墙板自攻螺钉 GB /T 14210-93十字槽盘头自钻自攻螺钉 GB /T 15856.1-2002十字槽沉头自钻自攻螺钉 GB /T 15856.2-2002十字槽半沉头自钻自攻螺钉 GB /T 15856.3-2002六角法兰面自钻自攻螺钉 GB /T 15856.4-2002六角凸缘自钻自攻螺钉 GB /T 15856.5-2002六角凸缘自攻螺钉 GB /T 16824.1-1997六角法兰面自攻螺钉 GB /T 16824.2-1997螺栓方头螺栓 C级 GB 8-88沉头方颈螺栓 GB 10-88沉头带榫螺拴 GB 11-88半圆头方颈螺栓 GB 12-88半圆头带榫螺栓 GB 13-88大半圆头方颈螺栓 C级 GB 14-1998大半圆头带榫螺栓 GB 15-88六角头铰制孔用螺栓 GB 27-88六角头螺杆带孔铰制孔用螺栓 GB 28-88六角头头部带槽螺栓 A 和 B 级 GB 29.1-88十字槽凹穴六角头螺栓 GB 29.2-88六角头螺杆带孔螺栓 GB 31.1-88 垫圈标准型弹簧垫圈 GB 93-87平垫圈 C级 GB /T 95-2002大垫圈 A级 GB /T 96.1-2002大垫圈 C级 GB /T 96.2-2002平垫圈 A级 GB /T 97.1-2002平垫圈倒角型 A级 GB /T 97.2-2002销轴用平垫圈 GB /T 97.3-2000平垫圈用于螺钉和垫圈组合件 GB /T 97.4-2002平垫圈用于自攻螺钉和垫圈组合件 GB /T 97.5-2002 小垫圈 A级GB /T 848-2002球面垫圈 GB 849-88锥面垫圈 GB 850-88开口垫圈 GB 851-88工字钢用方斜垫圈 GB 852-88槽钢用方斜垫圈 GB 853-88单耳止动垫圈 GB 854-88双耳止动垫圈 GB 855-88外舌止动垫圈 GB 856-88圆螺母用止动垫圈 GB 858-88轻型弹簧垫圈 GB 859-87鞍形弹性垫圈 GB 860-87内齿锁紧垫圈 GB 861.1-87内锯齿锁紧垫圈 GB 861.2-87外齿锁紧垫圈 GB 862.1-87外锯齿锁紧垫圈 GB 862.2-87波形弹性垫圈 GB 955-87六角头螺杆带孔螺栓细杆 B级 GB 31.2-88六角头螺杆带孔螺栓细牙 A和B级 GB 31.3-88六角头头部带孔螺栓 A 和 B级 GB 32.1-88六角头头部带孔螺栓细杆 B级 GB 32.2-88六角头头部带孔螺栓细牙 A 和 B 级 GB 32.3-88 下方头螺栓 B级GB 35-88T 形槽用螺栓 GB 37-88加强半圆头方颈螺栓 GB /T794-93活节螺栓 GB 798-88地脚螺栓 GB 799-88沉头双榫螺 GB 800-88小圆半头低方颈螺栓 B级 GB /T 801-1998六角头螺栓 C级 GB /T 5780-2000六角头螺栓全螺纹 C级 GB /T 5781-2000六角头螺栓 GB /T 5782-2000六角头螺栓全螺纹 GB /T 5783-2000六角头螺栓-细杆-B级 GB 5784-86六角头螺栓细牙 GB /T 5785-2000六角头螺栓细牙全螺纹 GB /T 5786-2000六角法兰面螺栓-加大系列-B级 GB 5789-86六角法兰面螺栓-加大系列-细杆-B级 GB 5790-86 六角法兰面螺栓小系列 GB /T 16674-1996钢网架螺栓球节点用高强度螺栓 GB /T 16939-1997螺柱双头螺柱 bm=1d GB 897-88双头螺柱 bm=1.25d GB 898-88双头螺柱 bm=1.5d GB 899-88 锥形弹性垫圈 GB 956.1-87锥形锯齿锁紧垫圈 GB 956.2-87特大垫圈 C级 GB /T 5287-2002重型弹簧垫圈 GB 7244-87鞍形弹簧垫圈 GB 7245-87波形弹簧垫圈 GB 7246-87销开口销 GB /T 91-2000圆锥销 GB /T 117-2000内螺纹圆锥销 GB /T 118-2000圆柱销不淬硬钢和奥氏体不锈钢 GB /T 119.1-2000圆柱销淬硬钢和马氏体不锈钢 GB /T 119.2-2000内螺纹圆柱销不淬硬钢和奥氏体不锈钢 GB /T 120.1-2000 内螺纹圆柱销淬硬钢和马氏体不锈钢 GB /T 120.2-2000 开尾圆锥销 GB 877-76螺纹圆柱销 GB 878-86弹性圆柱销直槽重型 GB /T 879.1-2000 弹性圆柱销直槽轻型 GB /T 879.2-2000 弹性圆柱销卷制重型 GB /T 879.3-2000 弹性圆柱销卷制标准型 GB /T 879.4-2000 弹性圆柱销卷制轻型 GB /T 879.5-2000 带孔销 GB 880-86螺尾锥销 GB /T 881-2000销轴 GB 882-86槽销平行沟槽 GB /T 13829.1-92槽销锥销 GB /T 13829.2-92槽销圆头沉头 GB /T 13829.3-92双头螺柱 bm=2d GB 900-88等长双头螺柱 B级 GB 901-88手工焊用焊接螺柱 GB 902.1-89机动弧焊用焊接螺柱 GB 902.2-89储能焊用焊接螺柱 GB 902.3-89等长双头螺柱 C级 GB 953-88螺杆 GB /T 15389-94螺母方螺母 C级 GB 39-88六角螺母 C级 GB /T41-2000六角厚螺母 GB 56-88蝶形螺母 GB 62-88环形螺母 GB 63-88组合式盖形螺母 GB 802-88球面六角螺母 GB 804-88扣紧螺母 GB 805-88滚花高螺母 GB 806-88滚花薄螺母 GB 807-88小六角特扁细牙螺母 GB 808-88嵌装圆螺母 GB 809-88小圆螺母 GB 810-88圆螺母 GB 812-88端面带孔圆螺母 GB 815-88侧面带孔圆螺母 GB 816-88带槽圆螺母 GB 817-881型非金属嵌件六角锁紧螺母 GB /T 889.1-20001型非金属嵌件六角锁紧螺母细牙 GB /T 889.2-2000 木螺钉开槽圆头木螺钉 GB 99-86开槽沉头木螺钉 GB 100-86开槽半沉头木螺钉 GB 101-86 六角头木螺钉 GB 102-86十字槽圆头木螺钉 GB 950-86 十字槽沉头木螺钉 GB 951-86 十字槽半沉头木螺钉 GB 952-86柳钉平头铆钉 GB 109-86标牌铆钉 GB 827-86半圆头铆钉 GB 863.1-86小半圆头铆钉 GB 863.2-86平锥头铆钉 GB 864-86沉头铆钉 GB 865-86半沉头铆钉 GB 866-86半圆头铆钉 GB 867-86平锥头铆钉 GB 868-86沉头铆钉 GB 869-86半沉头铆钉 GB 870-86扁圆头铆钉 GB 871-86扁平头铆钉 GB 872-86扁圆头半空心铆钉 GB 873-86 沉头半空心铆钉 GB 874-86 120°扁平头半空心铆钉 GB 875-86 空心铆钉 GB 876-86盖形螺母 GB 923-881型六角螺母 GB /T 6170-20001型六角螺母细牙 GB /T 6171-2000六角薄螺母 GB /T 6172.1-2000非金属嵌件六角锁紧薄螺母 GB /T 6072.2-2000六角薄螺母细牙 GB /T 6173-2000六角薄螺母无倒角 GB /T 6174-20002型六角螺母 GB /T 6175-20002型六角螺母细牙 GB /T 6176-2000六角法兰面螺母 GB /T 6177.1-2000六角法兰面螺母细牙 GB /T 6177.2-20001型六角开槽螺母-A和B级 GB 6178-861型六角开槽螺母-C级 GB 6179-862型六角开槽螺母-A和B级 GB 6180-86六角开槽薄螺母-A和B级 GB 6181-862型非金属嵌件六角锁紧螺母 GB /T 6182-2000非金属嵌件六角法兰面锁紧螺母 GB /T 6183.1-2000非金属嵌件六角法兰面锁紧螺母细牙 GB /T 6183.2-2000 1型全金属六角锁紧螺母 GB /T 6184-20002型全金属六角锁紧螺母 GB /T 6185.1-20002型全金属六角锁紧螺母细牙 GB /T 6185.2-20002型全金属六角锁紧螺母 9级 GB /T 6186-2000全金属六角法兰面锁紧螺母 GB /T 6187.1-2000全金属六角法兰面锁紧螺母细牙 GB /T 6187.2-20001型六角开槽螺母细牙 A和B级 GB 9457-882型六角开槽螺母细牙 A和B级 GB 9458-88六角开槽薄螺母细牙 A和B级 GB 9459-88焊接方螺母 GB /T 13680-92 沉头铆钉 GB 954-86 120°管状铆钉 GB 975-86大扁圆头铆钉 GB 1011-86半沉头铆钉 GB 1012-86 120°平锥头半空心铆钉 GB 1013-86大扁圆头半空心铆钉 GB 1014-86沉头半空心铆钉 GB 1015-86无头铆钉 GB 1016-86封闭型扁圆头抽芯铆钉 GB 12615-90封闭型沉头抽芯铆钉 GB 12616-90开口型沉头抽芯铆钉 GB 12617-90开口型扁圆头抽芯铆钉 GB 12618-90扁圆头击芯铆钉 GB /T 15855.1-1995沉头击芯铆钉 GB /T 15855.2-1995紧固件-组合件和连接副钢结构用高强度大六角头螺栓 GB /T 1228-91钢结构用高强度大六角头螺母 GB /T 1229-91钢结构用高强度垫圈 GB /T 1230-91钢结构用扭剪型高强度螺栓连接副 GB /T 3632-1995螺栓或螺钉和平垫圈组合件 GB /T 9074.1-2002十字槽头螺钉和外锯齿锁紧垫圈组合件 GB 9074.2-88十字槽盘头螺钉和弹簧垫圈组合件 GB 9074.3-88十字槽盘头螺钉、弹簧垫圈和平垫圈组合件GB 9074.4-88 十字槽小盘头螺钉和平垫圈组合件 GB 9074.5-88十字槽小盘头螺钉和大垫圈组合件 GB 9074.6-88十字槽小盘头螺钉和弹簧垫圈组合件 GB 9074.7-88十字槽小盘头螺钉、弹簧垫圈和平垫圈组合件GB 9074.8-88 十字槽沉头螺钉和锥形锁紧垫圈组合件 GB 9074.9-88焊接六角螺母 GB /T 13681-92平头铆螺母 GB /T 17880.1-1999沉头铆螺母 GB /T 17880.2-1999小沉头铆螺母GB /T 17880.3-1999 120°小沉头铆螺母GB /T 17880.4-1999 平头六角铆螺母 GB /T 17880.5-1999精密机械用六角螺母 GB /T 18195-2000螺钉开槽圆柱头螺钉 GB /T 65-2000开槽盘头螺钉 GB /T 67-2000开槽沉头螺钉 GB /T 68-2000开槽半沉头螺钉 GB /T 69-2000内六角圆柱头螺钉 GB /T 70.1-2000内六角平圆头螺钉 GB /T 70.2-2000内六角沉头螺钉 GB /T 70.3-2000开槽锥端紧定螺钉 GB 71-85开槽锥端定位螺钉 GB 72-88开槽平端紧定螺钉 GB 73-85开槽凹端紧定螺钉 GB 74-85开槽长圆柱端紧定螺钉 GB 75-85内六角平端紧定螺钉 GB /T 77-2000内六角锥端紧定螺钉 GB /T 78-2000内六角圆柱端紧定螺钉 GB /T 79-2000 内六角凹端紧定螺钉 GB /T 80-2000方头长圆柱球面端紧定螺钉 GB 83-88方头凹端紧定螺钉 GB 84-88方头长圆柱端紧定螺钉GB 85-88 十字槽半沉头螺钉和锥形锁紧垫圈组合件 GB 9074.10-88十字曹凹穴六角头螺栓和平垫圈组合件 GB 9074.11-88十字槽凹穴六角头螺栓和弹簧垫圈组合件 GB 9074.12-88十字槽凹穴六角头螺栓、弹簧垫圈和平垫圈组合件GB 9074.13-88 六角头螺栓和弹簧垫圈组合件 GB 9074.15-88六角头螺栓和外锯齿锁紧垫圈组合件 GB 9074.16-88六角头螺栓、弹簧垫圈和平垫圈组合件 GB 9074.17-88自攻螺钉和平垫圈组合件 GB /T 9074.18-2002十字槽凹穴六角头自攻螺钉和平垫圈组合件 GB 9074.20-88十字槽凹穴六角头自攻螺钉和大垫圈组合件 GB 9074.21-88组合件用弹簧垫圈 GB 9074.26-88组合件用外锯齿锁紧垫圈 GB 9074.27-88组合件用锥形锁紧垫圈 GB 9074.28-88腰状杆螺柱连接副型式分类 GB /T 13807.1-92腰状杆螺柱连接副螺柱 GB /T 13087.2-92腰状杆螺柱连接副螺母、受力套管 GB /T 13087.3-92焊钉电弧螺柱焊用圆柱头焊钉 GB /T 10433-2002无头焊钉 GB 10432-89方头短圆柱锥端紧定螺钉 GB 86-88 十字槽盘头螺钉 GB /T 818-2000 六角头不脱出螺钉 GB 838-88滚花头不脱出螺钉 GB 839-88美制英制德标对照表——德制弹簧垫圈美制英制德标对照表——自攻螺钉。