精研SK系列内置式调速器

操作终端说明书（触摸屏）武汉四创自动控制技术有限责任公司目录一、系统概述 (2)二、画面简介 (2)1.状态指示画面 (3)2.操作画面 (4)3.主菜单画 (5)4.密码框 (6)5.数值键盘画面 (7)6.参数设置 (8)7.导叶参数设置 (9)8.浆叶参数设置（*双调机组） (11)9.功率参数设置 (13)10.大网参数、小网参数、空载参数、负载频率参数 (14)11．水头参数设置 (15)12．PID优化参数设置 (16)13.过程监视 (17)14.动态过程记录 (18)15.空载频率扰动 (18)16.空载频率摆动 (20)17.甩负荷试验 (20)18.故障查询 (21)19.协联数据（*双调机组） (22)一、系统概述图示操作终端可对调速器的各种状态进行监视，如开机、停机、并网、调相、机械手动/自动、水头手动/自动、跟踪网频/跟踪频给等。

用触摸键代替按钮，当需要增加某些按键时，只须修改程序，避免了采用按钮须修改硬件的敝端。

可对调速器进行静态、动态试验；对不同操作人员设置不同的权限，只有知道密码方可操作；对采样数据和报警记录进行存储，并可打印。

图示操作终端采用24V供电，背景灯使用寿命长，亮度可根据现场进行调整。

当调速器处于运行状态而没有任何操作时，背景灯到一定时间就熄灭。

这时，画面呈黑色，当需要看画面内容时，只须用手点屏幕即可。

也可以不用此功能，而使画面总是处于显示状态。

二、画面简介图示操作终端由各种画面组成，每个画面具有不同的功能。

当进行画面操作时，请勿用尖、硬物体点画面，以免损坏机器。

下面对各种画面进行介绍。

1.状态指示画面状态指示画面双调机组状态指示画面（*双调机组）状态指示画面如图所示。

该画面显示调速器的各种状态：开机、停机、并网、调相、开度调节/功率调节、机械自动/机械手动、浆叶手动/自动（双调机组）、水头手动/水头自动、跟踪频给/跟踪网频、调速器故障/调速器正常、停机备用、故障锁定。

Absolute maximum ratingsSymbol Conditions Unit I IN MAX Maximum permanent input current A RMS I OUT MAX Maximum permanent output current A RMS V IN MAX Maximum input voltage V AC V OUT MAX Maximum output voltage V AC V BUS MAX Maximum DC Bus voltage V DC F IN MAX Inverter input frequency Hz F OUT MAX Inverter output frequency Hz F SW MAX Maximum switching frequency kHzElectrical characteristics TAMBIENT= 40°C unless otherwise specifiedSymbol Conditionsmin typ max UnitI OUT RATED Rated output current 2 400A RMSI OUT OVL Overload output current 2 640A RMSt OVL Overload duration60sT OVL Time between 2 overloads10minV OUT Output voltage620690760V AC SKiiPRACK® - Type 6A P OUT Rated output power 2 870kW 4-Quadrant 3-phase IGBT converter F SW Inverter switching frequency2kHzF OUT Output frequency50HzPF Power factor1-P LOSS INV2)Losses at rated current28 320W Ordering No.08800600η2)Efficiency at rated current99% Description SKS C 240 GDD 69/11 – A6A MA B1C AC phase GeneratorI IN RATED Rated input current 2 400A RMS Features I IN OVL Overload input current 2 640A RMSt OVL Overload duration60sDesigned in regard to EN50178 recommendations T OVL Time between 2 overloads10min Designed for a 1200 x 600 x 2000 mm cabinet V OUT Output voltage620690760V AC Embedded SKiiP® Technology 3P OUT Rated output power 2 870kW SKiiP 2403GB172-4DW, Trench 3 1700V IGBT, CAL3 diode F SW Inverter switching frequency2kHz Integrated current and temperature sensors F OUT Output frequency20100Hz Water cooling PF Power factor-1-P LOSS INV2)Losses at rated current28 320Wη2)Efficiency at rated current99% Typical ApplicationsDC BusWind generators (SG and DFIG)V BUS Rated DC voltage applied to the capacitor bank 1 100V DC High power AC drives V BUS MAX Max DC voltage applied to the caps bank (max 30% of LTE) 1 200V DCτd5%Discharge time of the capacitors (V DC < 60 V)6min Footnotes C DC Capacitor bank capacity27,0mFLTE Calculated LTE of the capacitors with forced air cooling100kh 1) Absolute maximum ratings are values not to beexceeded in any case and do not imply that the stack Stack Insulationcan operate in all these conditions taken together Crd Minimum creepage distance8,7 mm 2) fan consumption and losses in air included Cld Minimum clearance distance7,1 mmVisol Chassis / Power stage AC/DC (insulation test voltage DC, 5 s)-4 200 4 200V DC REMARKSVisol12SKiiP driver only, output 1 / output 2 (AC, rms, 2 s) 1 500Vdv/dt SKiiP driver only, secondary to primary side75kV/µs B6CI + B6CISKiiP stackV BUS = 1 100 V DCT INLET = 45°C, 50% glycolFlowrate = 12 L/min per cellT J < 125°CAir extraction according to thermaldata page 2V BUS = 1 100 V DCT INLET = 45°C, 50% glycolFlowrate = 12 L/min per cellT J < 125°CAir extraction according to thermaldata page 2This technical information specifies semiconductor devices butpromises no characteristics. No warranty or guarantee,expressed or implied is made regarding delivery, performanceor suitability.Before using the converter, please read carefully theSKiiPRACK® user manual.Values2 400760AC phase Grid2 40010010057601 200Environmental conditions T AMBIENT=40°C unless otherwise specified Characteristics Conditions min typ max UnitAmbiant temperature 1)HumidityInstallation altitude without derating 1 000mMax. installation altitudewith derating 4 000mProtection degreeIEC 60529IP00-IEC 60721-3-2, storage & transportation, 1 cell2M1-IEC 60721-3-3, in operation, 1 cell3M3-Pollution degree EN 501782-Cell80kg4-Quadrant converter550kgThermaldataSKiiPRACK® - Type 6A Water flow per cell81224L/min 4-Quadrant 3-phase IGBT converter Water flow per 4Q-converter4872144L/minOrdering No.08800600Description SKS C 240 GDD 69/11 – A6A MA B1C Water pressure Maximum water pressure permissible per cell3barCoolant type Recommended coolant50% Glycol / 50% water-Features T INLET Cooling water inlet temperature-204560°CExternal cooling airflow Snubbers, required airflow direction bottom-top1ms-1 Designed in regard to EN50178 recommendations V SUPPLY[fan]Capacitor DC fan operating voltage182428V DC Designed for a 1200 x 600 x 2000 mm cabinet P FAN per fan Fan power consumption at typical voltage supply3,6W Embedded SKiiP® Technology 3LTE[fan]Capacitor DC fan life time expectancy (L10 method)65kh SKiiP 2403GB172-4DW, Trench 3 1700V IGBT, CAL3 diodeIntegrated current and temperature sensors Gate Driver Characteristics T AMBIENT=25°C unless otherwise specified Water cooling Symbol Conditions min typ max UnitGate Driver / controler dataV S2 supply voltage non stabilized 132430V DC Typical Applications I S2 V S2 = 13V - 30 V, F SW in kHz, I AC in A330 + 55×F SW + 0.00035×I AC2mAViT+input threshold voltage HIGH 12,3V DC Wind generators (SG and DFIG)ViT-input threshold voltage LOW 4,6V DC High power AC drives R IN Input resistance10kΩC IN Input capacitance1nF Footnotes Measurement & protectionHB_I Analogue current signal HB_I245250255 A.V-1 1) the user shall ensure that the ambiant air is sufficiently I TRIPSC over current trip level(Ianalog OUT=10V) 2 450 2 500 2 550A PEAK ventilated to avoid hot spots.min17 + 10,3×CMN_TMP°CCMN_TMP Analogue temperature signal Th < 80°C typ19 + 10,5×CMN_TMP°Cmax20 + 10,5×CMN_TMP°Cmin26 + 8,8×CMN_TMP°C REMARKS CMN_TMP Analogue temperature signal Th > 80°C typ28 + 8,8×CMN_TMP°Cmax30 + 8,9×CMN_TMP°CT trip Over temperature protection110115120°C This technical information specifies semiconductor devices butpromises no characteristics. No warranty or guarantee,expressed or implied is made regarding delivery, performanceor suitability.Before using the converter, please read carefully theSKiiPRACK® user manual.5°C-2055°C∆P WATER150mbarMass∆V/∆t WATERPressure drop per cell with male and femaleconnectors, 50% glycol, 12 L/minPressure drop per 4Q converter with male andfemale connectors, 50% glycol, 72 L/min150 B6CI + B6CIClimaticMechanicalSKiiP stack6085%Vibrations & ShocksIEC 60721-3, class 1K2 & 2K2Storage & transportationIEC 60721-3-3, class 3K3 extendedIn operation-25IEC 60721-3-3, class 3K3no condensation no icingmbarDC+ DC-V1W1L31L21Phase driver connectorsDC BUS detailsDC BUS connection L11U2V2W2L32L22L12HE10-14 male connectorPinDesignation1+24VDC 2+24VDC 3GND 4GNDLEFT SIDE VIEW DC FAN CONNECTION (6 times)This technical information specifies semiconductor devices but promises no characteristics. No warranty or guarantee 12 3 4View XFRONT VIEW REAR VIEWU, V, W are generator side converter phasesL1, L2, L3 are grid side converter phases2 SKiiPs in parallel cannot be on the same SKiiPRACK cellThis technical information specifies semiconductor devices but promises no characteristics. No warranty or guaranteeDetails - View XThis technical information specifies semiconductor devices but promises no characteristics. No warranty or guarantee expressed or implied is made regarding delivery, performance or suitability.6Rev. 0 - 03.06.201300,0020,0040,0060,0080,010,0120,0145101520253035R t h (°C /W )Flowrate per cell (L/min)Stack Rth 50% glycol (°C/W)Stack Rth 10% glycol (°C/W)50010001500200025003000303540455055O u t p u t c u r r e n t (A R M S )Ambient air temperature (°C)Cooling liquid 45°C Cooling liquid 60°CV BUS = 1 100 V DCVac IN/OUT =690 V RMS F IN/OUT = 50 Hz f SW IN/OUT = 2 kHz cos ϕIN/OUT = 1Flowrate = 12 L/min per cell Glycol/water ratio = 50%Altitude <1000 m 0500100015002000250030005001000150020002500300035004000O u t p u t c u r r e n t (A R M S )Altitude (m)Cooling liquid 45°C, ambient 40°C Cooling liquid 60°C, ambient 55°CV BUS = 1 100 V DCFlowrate = 12 L/min per cell Vac IN/OUT =690 V RMS Glycol/water ratio = 50%F IN/OUT = 50 Hz Altitude <1000 mf SW IN/OUT = 2 kHz cos ϕIN/OUT = 1050010001500200025003000200400600800100012001400M a x c u r r e n t s w i t c h e d (A )DC bus voltage (V)0100200300400500600700510152025P r e s s u r e d r o p p e r S K i i P R A C K c e l l (m b a r )Flowrate (L/min)Pressure drop with 50% glycolPressure drop without glycol (mbar)0500100015002000250051015O u t p u t C u r r e n t (A R M S )AC Fundamental Frequency (Hz)V BUS = 1 100 V DCVac IN/OUT =690 V RMS f SW IN/OUT = 2 kHz cos ϕIN/OUT = 1Water temperature = 45°C Flowrate = 12 L/min per cell Glycol/water ratio = 50%Air temperature = 40°C T J = 125°C。

用户指南安装使用前请仔阅读本说明书目录引言产品外观系统功能主要参数安装接线基本操作联网设置故障检修原装附件软件安装门禁软件考勤软件一、引言：感谢您使用本非接触式感应卡门禁考勤管理系统，在使用本系统之前，请您详细阅读本用户指南，并严格按照手册中的要求来操作。

此用户指南将介绍本系统主要功能及操作使用方法。

本门禁系统采用目前世界上先进的技术-非接触式感应卡技术（也称射频识别卡（RFID）技术，RFID卡具有全球卡号唯一、不易仿制的读写特性和安全性能。

RFID卡片不会产生使用磁卡时因磁头磨损、磁粉脱落、灰尘等影响所带来的麻烦，而且避免了接触式IC卡因芯片与读卡器外露而引起的沾污、接触不良和外物损伤而导致的读卡不良现象，RFID卡适应各种环境，经久耐用。

每一次感应卡读的信息，无论是否向电锁发出开锁指令，系统都自动记录下来，管理者可以通过计算机下载调阅门禁控制系统存储的信息资料，轻松查阅、打印所有的通行事件。

管理软件将根据此原始资料自动统计员工考勤情况、编制考勤报表。

本系统提供了一种智能化的出入口控制及考勤管理方式，适用于需要控制人员出入的通道、商务机构、政府机关、住宅小区等等。

二、产品外观：465604162465604162三、系统功能：1、存储容量达8000条通行记录，1000张用户卡及密码2、每天自由设定八个限制通行时段3、具备读卡开门、读卡加密码开门、读卡或密码开门三种方式4、内置、外接读卡器，可实时区分进入、外出人次数5、采用RS485总线联网通讯方式，布线简易实用，联网可达64台6、19,200Bps高速传输下载数据7、主要输入/输出功能：电锁、开门按钮、报警器、门磁、门铃8、管理软件集门禁、考勤、人事于一体9、管理软件界面人性化，操作简易，使用方便10、系统图示可导入电子地图，自由设定门的名称、位置11、实时显示通过人员的姓名、相片、卡号、编号等资料12、自定义考勤规则及班次设定等13、自动统计迟到、早退、缺勤的次数及时间14、考勤结果可打印成报表或按Excel导出,.四、主要参数：五、安装接线：1．接线示意图：注：不要带电安装接线；不要从控制器直接接锁，电锁直接由电源接出；2．接线说明：A、读卡器到控制器的线，建议用6芯屏蔽多股双绞网线（其中2芯备用），数据线Data1 Data0互为双绞。

JD、JZT、ZLK、ZTK系列电磁调速电动机控制装置J D、JZT、ZLK、ZTK系列电磁调速电动机控制器是原机械工业部全国联合(统一)设计产品，用于电磁调速电动机(滑差电机)的调速控制，实现恒转矩无级调速。

本控制器只适用于滑差电机不适用于普通电机。

1 适用范围3.1 调速范围电源：~220V(±10%)，50Hz或60Hz、100r/min~1300r/min3.2 转速变化率(机械特性硬度)≤2.5%；3.3 稳速精度：≤1%；3.4 最大输出：DC90V,8A；3.5 控制电机功率：0.55kW90kW；3.6 测速发电机三相中频电压转速比：≥2V/100r/min。

~JD、JZT、ZLK、ZTK □□-□被控电动机最大功率(W)A：手操普通型 B：手操精密型设计序号(1-指针式 2-数显式 3和4-指针式，容量不同见表3)电磁调速电机控制器5%负载下的转-100%负载下的转速额定转速转速变化率=×100%3 主要参数及技术性能2 型号及含义插头号码1234567连接对应的名称~220V~220V离合器激励绕组F1离合器激励绕组F2测速发电机输出端U测速发电机输出端V测速发电机输出端W222注：F1、F2选用导线(推荐)0.55kW~40kW：1mm铜导线；45kW-90kW：1.5mm铜导线；U、V、W 导线选用 (推荐)0.75mm2或1mm铜导线。

型号电源电压最大输出定额(直流90V)可控制电动机功率(kW)测速发电机转速变化率稳速精度调速范围(r/min)JD A-11~220V(±10%) 50Hz~60Hz3.15A0.55~11三相中频电压转速比为≥2V/100r/min≤2.5%≤1%1300~1003.7 手操普通型12JD A-405A15~401300~100JD A-90*8A45~901300~130表 11212F3.8 手操精密型型号电源电压最大输出定额(直流90V)可控制电动机功率(kW)测速发电机转速变化率调速范围(r/min)JD B-11~220V(±10%) 50Hz~60Hz3.15A0.55~11三相中频电压转速比为≥2V/100r/min≤1%1300~10012JD B-405A15~401300~100JD B-90*8A45~901300~1303.9 JZT、ZLK-1、ZTK-1技术参数型号电源电压最大输出定额(直流90V)可控制电动机功率(kW)测速发电机转速变化率调速范围(r/min)JZT3~220V(±10%) 50Hz60Hz5A0.5540单相或三相中频电压转速比为≥2V/100r/min≤2.5%1300~100~~JZT48A45901300~130~ZLK-15A0.55401300100~~ZTK-18A45~901300~1305A0.55401300100~~表2表3*：大于8A小于12A时，其工作时间不大于30min。

JD1A-40JD1A电磁调速电动机控制器1. 简介JD1A-40JD1A电磁调速电动机控制器是一种专用于电动机调速的设备。

它采用电磁调速方式，通过调节电机的电源电压和频率来实现电机的调速控制。

2. 特点电磁调速：通过控制电机的电源电压和频率，实现电机的调速控制。

稳定性高：控制器采用先进的控制算法和传感器，保证电机的稳定运行。

易于操作：控制器配备了直观的操作界面和人性化的按键，方便用户进行参数设置和操作。

多种保护功能：控制器具备过载保护、过热保护、短路保护等多种保护功能，保证电机的安全运行。

多种工作模式：控制器支持多种工作模式，满足不同应用场景的需求。

3. 技术参数额定功率：40KW额定电压：380V控制方式：电磁调速控制精度：±2%工作温度：-10℃～＋55℃接口：RS485、MODBUS重量：10kg4. 应用领域JD1A-40JD1A电磁调速电动机控制器广泛应用于工业生产线、机械设备、风扇、水泵等需要调速控制的场合。

它具备稳定性高、操作简单、保护功能多等特点，能够满足不同场景的调速需求。

5. 安装与维护安装：请按照产品说明书中的安装步骤进行安装，确保设备安装牢固。

维护：控制器需要定期清理和检查，及时修复故障并更换损坏的部件。

6. 注意事项在使用过程中，请确保设备连接正确，以免引起电机或其他设备故障。

请勿超过产品的额定功率和额定电压，以免危及安全。

在操作控制器时，请谨慎调节参数，以免影响电机的正常运行。

以上是关于JD1A-40JD1A电磁调速电动机控制器的基本介绍，希望能对大家有所帮助。

如有更多问题，请咨询相关厂家或专业人士。

SSE苏州迅达电梯有限公司215004 苏州/中国Skiip模块说明技术培训中心编制：李志弘2003/05/13 A. 变频功率装置所用大功率晶体管的重要参数比较：双极晶体管MOS IGBT 驱动方式电流电压电压载波频率≤3KHz ≤60 KHz ≤20KHz 电流容量中低中击穿电压中低高短路安全工作区好好不好饱和电压高低中综合特点1．电机啸叫噪音高2．调制精度要求不高3．输出容量小4．截止频率低5．抗短路性能好1．输出容量小2．输出电压、电流小3．调制精度高4．无噪音5．截止频率高1．输出容量大2．输出电压、电流大3．调制精度高4．当载波频率≥10.8KHz时，电机无啸叫声。

5．功率因素可达16．抗短路性能差B．变频器基本工作原理：变频器工作基本原理如下：a. 三相交流电源输入三相桥式整流器整流。

（将AC变为DC）b. 整流后进入直流中间回路滤波。

（对DC进行滤波）c. 滤波后的直流电进入逆变器（由六个IGBT组成）。

（再将DC逆变成频率、电压可变的三相交流电）d. 由驱动控制部分控制逆变器的导通和关断，把直流电压转换成新的频率和电压均可调制的三相交流电源，U2，f2，于是电机就以设定速度n运行。

e. 驱动控制部分能形成闭环控制，同时监控整个系统。

f. 电机处于发电状态时（例如：电梯空载上行或重载下行的减速时）制动斩波器工作，通过制动电阻R使多余能量消耗。

（也可采用逆变至送电电网）电梯所用逆变器基本上都采用IGBT型场效应管作为开关管。

C.变频器主要特性分析：1．变频器在逆变输出期间，其输出端的三相交流电压中包含着nfc（fc为载波频率，n= 1,2…）的高次谐波，而这种频率的谐波电压会使电机产生刺耳的噪音，通常采取的措施是增加载波频率使之大于10.8KHz，使电机共振啸叫噪音超出工频电源的频率，从而保证频率在0~50Hz范围内变化时，电机无噪音。

但在增加载波频率的同时，会增加变频器周围电磁波的发射，导致周围的空间污染，这已经在欧、美国家引起高度重视和法律、法规的限制。

SK120,SK200,SK350 Series Pure Sine Wave InverterUser’s ManualTable of contents1. Important Safety Information.……………………………………………… 1-1 General Safety Precautions……………………………………………1-2Precautions When Working with Batteries……….…………………..2. Features………………………………………………………………………... 2-1 Electrical Performance………………………………………………… 2-2 Mechanical Drawing of Socket Type(Power Claw PP75)… …..….2-3Mechanical Drawing of Strip Wire Type……………….…………….3. Instructions………………………………………………….………………… 3-1 Front Panel Operation..………………………………………………...3-2Rear Panel Operation..…………………………………………………3-3 Protections Features……..……………………………………………. 3-4 Installation.………………………………………………….…………...3-5Making DC Wiring Connections……...………………………………..3-6 AC Safety Grounding…………………………………………………... 3-7 Inverter Operation……………………………………………………… 4. Troubleshooting guide……………………………………………………… 5. Maintenance……………………………………………………………………6. Warranty………………………………………………………………………..D Copyright ：This manual is the copyright of COTEK Electronic lnd. Co., Ltd. Be not allowed to reproduc or copywithout permission of the owner.1. Important Safety Information1-1. General Safety Precautions1-1-1. Do not expose the Inverter to rain, snow, spray, bilge or dust.To reduce risk of hazard, do not cover or obstruct the ventilationopenings. Do not install the Inverter in a zero-clearance compartment.Over heating may result.1-1-2. To avoid a risk of fire and electronic shock. Make sure that existing wiring is in good electrical condition; and that wire size is notundersized.Do not operate the Inverter with damaged or substandard Wiring.1-1-3. This equipment contains components which can produce arcs or sparks. To prevent fire or explosion do not install in compartmentscontaining batteries or Flammable materials or in locations whichrequire ignition protected equipment. This includes any spacecontaining gasoline-powered machinery, fuel tanks, or joints, fittings,or other connection between components of the fuel system.1-2. Precautions When Working with Batteries1-2-1. If battery acid contacts skin or clothing, wash immediately with soap and water. If acid enters eye, immediately flood eye with runningcold water for at least 20 minutes and get medical attentionimmediately.1-2-2. Never smoke or allow a spark or flame in vicinity of battery or engine.1-2-3. Do not drop a metal tool on the battery. The resulting spark orshort-circuit on the battery of other electrical part may cause anexplosion.1-2-4. Remove personal metal items such as rings, bracelets, necklaces, and watches when working with a lead-acid battery,A lead-acid battery produces a short-circuit current high enough toweld a ring or the like to metal, causing a severe burn.2. FeaturesPure sine wave output (THD < 3%)Output frequency：50 / 60Hz switch selectionsInput & output completely isolated designHigh efficiency 84~94%Capable of driving inductive & capacitive loads at the start moment.A LED Indicator with twin color displays all operation status.Loading and temperature controlled cooling fan.Built in advanced microprocessor to make friendly interface with user.Protection：Input low voltage Overload Short circuit Low battery alarm Input over voltage Over temperature2-1. Electrical PerformanceItem SK120-112SK120-124SK120-148SK120-212 SK120-224 SK120-248 Continuous Output Power 120WMaximum Output Power 132WSurge Rating (Max) 240WInput voltage 12Vdc 24Vdc 48Vdc 12Vdc 24Vdc 48Vdc Output Voltage 100 / 110 / 120Vac +/- 5% 220 / 230 / 240Vac +/- 3%Frequency(Switch Selections)50 / 60Hz +/- 0.05%Output Waveform Pure Sine Wave ( THD < 3% ) Efficiency (full load) Max *1 89% 91% 93% 92% 93% 94%Input Voltage Regulation 10.5-15VDC21.0-30VDC42-60VDC10.5-15VDC21.0-30VDC42-60VDCFailure Indicator Red LEDProtectionOverload (Shut down),Short Circuit (Shut down),Reverse Polarity (Fuse), Over / Under Input Voltage (Auto recovery), Over Temperature (Auto recovery).Remote Control Yes (ON / OFF mode controlled by hard wire) See 3-2 Safety Meet UL458 EN60950-1EMC FCC Class A EN55022:1997EN61000-3-2:1998EN61000-3-3:1995EN55024:2001e-marke13 023495Operating Temperature Range 0 - 40 ℃Storage Temperature Range -30℃ to 70℃Cooling convection coolingDimensions 185(L)x147(W)x60(H)mm / 7.3(L)x5.8(W)x2.36(H) Inch Weight 1kgNote: The specifications are subject to change without notice.Item SK200-112SK200-124SK200-148SK200-212 SK200-224 SK200-248 Continuous Output Power 200WMaximum Output Power 220WSurge Rating (Max) 400WInput voltage 12Vdc 24Vdc 48Vdc 12Vdc 24Vdc 48Vdc Output Voltage 100 / 110 / 120Vac +/- 5% 220 / 230 / 240Vac +/- 3%Frequency(Switch Selections)50 / 60Hz +/- 0.05%Output Waveform Pure Sine Wave ( THD < 3% )Efficiency (full load) Max *187% 90% 92% 90% 93% 94%Input Voltage Regulation 10.5-15VDC21.0-30VDC42-60VDC10.5-15VDC21.0-30VDC42-60VDCFailure Indicator Red LEDProtectionOverload (Shut down),Short Circuit (Shut down),Reverse Polarity (Fuse), Over / Under Input Voltage (Auto recovery), Over Temperature (Auto recovery).Remote Control Yes (ON / OFF mode controlled by hard wire) See 3-2 Safety Meet UL458 EN60950-1EMC FCC Class A EN55022:1997EN61000-3-2:1998EN61000-3-3:1995EN55024:2001e-marke13 023496Operating Temperature Range 0 - 40 ℃Storage Temperature Range -30℃ to 70℃Cooling FAN (Controlled by load and temperature)Dimensions 185 (L) x 147 (W) x 60 (H) mm / 7.3 (L) x 5.8 (W) x 2.36 (H) Inch Weight 1.2kgNote: The specifications are subject to change without notice.Item SK350-112SK350-124SK350-148SK350-212 SK350-224 SK350-248 Continuous Output Power 350WMaximum Output Power 385WSurge Rating (Max) 700WInput voltage 12Vdc 24Vdc 48Vdc 12Vdc 24Vdc 48Vdc Output Voltage 100 / 110 / 120Vac +/- 5% 220 / 230 / 240Vac +/- 3%Frequency(Switch Selections)50 / 60Hz +/- 0.05%Output Waveform Pure Sine Wave ( THD < 3% )Efficiency (full load) Max *184% 86% 88% 86% 89% 90%Input Voltage Regulation 10.5-15VDC21.0-30VDC42-60VDC10.5-15VDC21.0-30VDC42-60VDCFailure Indicator Red LEDProtectionOverload (Shut down),Short Circuit (Shut down),Reverse Polarity (Fuse), Over / Under Input Voltage (Auto recovery), Over Temperature (Auto recovery).Remote Control Yes (ON / OFF mode controlled by hard wire) See 3-2 Safety Meet UL458 EN60950-1EMC FCC Class A EN55022:1997EN61000-3-2:1998EN61000-3-3:1995EN55024:2001e-marke13 023497Operating Temperature Range 0 - 40 ℃Storage Temperature Range -30℃ to 70℃Cooling FAN (Controlled by load and temperature)Dimensions 185(L)x147(W)x60(H)mm / 7.3(L)x5.8(W)x2.36(H) Inch Weight 1.4kgNote: The specifications are subject to change without notice.2-2. Mechanical Drawing of Socket (Power Claw PP75)2-3. Mechanical Drawing of Strip Wire Type3. InstructionsThis power inverter series is a the member of the most advanced line of mobile AC power systems available.To get the most out of the power inverter, it must be installed and used properly.Please read the instructions in this manual before installation and operation this model.3-1. Front Panel Operation：3-1-1. Front view：POWERSTATUS50HzFREQ.60HzAC OUTPUTPURE SINE WAVE INVERTERPURE SINEWAVE INVERTERAC OUTPUT60Hz50Hz FREQ.POWERSTATUS3-1-2. AC Frequency：Selected by Dip Switch50 HZ ON60 HZ OFF3-1-3. Status：Display Power & Fault Status3-1-4. AC Output (available Sockets)：3-1-5. DC Input (available type)：3-2. Rear Panel Operation ：3-2-1. ON / OFF / REMOTE Main Switch.3-2-1-1. Before installing the inverter, make sure the main switch mustbe “OFF”. 3-2-1-2. Before using the remote unit, make sure the main switch mustbe “ REMOTE”. 3-2-1-3. Ensure the remote control contact is off.3-2-1-4. Remote Port ：Place 0.75mm 2 and Screw type cable betweenthe remote port and the panel.3-2-1-5. Remote port ON/OFF inverter setup statusVCEO > VBATMODE Ⅱ MODE ⅠNOTE: Only one of control mode can be presented. When operating. 3-2-2. DC Input Terminals ：Connect to 12V / 24V / 48V battery or the other power sources. 【＋】is positive,【－】is negative. Reverse polarity connection will blow internal fuse and may damage inverter permanently.DC Input Voltage MinimumMaximum 12 V 10.5 15.0 24 V 21.0 30.0 48 V42.060.03-2-3. Chassis Ground: using # 8 AWG wire to connect vehicle chassis.MODE ⅢMODE Ⅳ3-3. Protections Features:12 V 16V 13V11.0V <10.5V12.524 V 32V 26V22.0V <21.0V25.055℃ 45℃48V 62V 52V44.0V <42.0V50.0Note: The specifications are subject to change without notice.3-4. Installation：Where to install. The power inverter should be installed in a location thatMeets the following requirements：3-4-1. Dry – Do not allow water to drip or splash on the inverter.3-4-2. Cool – Ambient air temperature should be between 0℃ and 40℃, the cooler the better.3-4-3. Safe – Do not install in a battery compartment or other areas where flammable fumes may exist, such as fuel storage areas or enginecompartments.3-4-4. Ventilated – Allow at least one inch of clearance around the inverter for air flow. Ensure the ventilation openings on the rear and frontof the unit are not obstructed.3-4-5. Dust – Do not install the Inverter in a dusty environmentswhere are dust, wood particles or other filings/shavings are present.These dust can be pulled into the unit when the cooling fan isoperating.3-4-6. Close to batteries – Avoid excessive cable lengths but do not install the Inverter in the same compartment as batteries.Use the recommended wire lengths and sizes (see section 3-5).Also do not mount the Inverter where it will be exposed to thegases produced by the battery.These gases are very corrosive and prolonged exposure also willdamage the Inverter.3-5. Making DC Wiring Connections：Follow this procedure to connect the battery cables to the DC input terminals of the Inverter. Your cables should be as short as possible (Ideally,less than 6 feet / 1.8 meters ) enough to handle the required current inaccordance with the electrical codes or regulations application. Cables are not an adequate gauge (too narrow) or too long will decrease the inverterperformances such as poor surge capability and low input voltage warnings frequently and shutdowns. UVP warning presents due to DC voltage drop across the cables from the inverter to the batteries.The longer or narrower the cables, the greater the voltage drop.Increasing your DC cable size will help improve the situation.Following cable recommendations for the best performance of inverter.(Apply both 120V and 230V versions )3-6. AC Safety Grounding：The AC output ground wire should go to the grounding point for your loads ( for example, a distribution panel ground bus ).3-6-1. Neutral Grounding (GFCI’S)：3-6-1-1. 120V models：The neutral conductor of the AC output circuit of the Inverter is automatically connected to the safetyground during inverter operation. In accordance with theNational Electrical Code requirements that separately derivedAC sources (such as inverter and generators) have theirneutral conductors tied to ground in the same way that theneutral conductor from the utility is tied to ground at the ACbreaker panel. For models configured with a transfer relay,while AC utility power is presenting and the Inverter is inbypass mode, this connection (neutral of the Inverter’s ACoutput to input safety ground) is not present so that the utilityneutral is only connected to ground at your breaker panel,as required.3-6-1-2. 230V models：There is no connection made inverter interiorbetween either the line or neutral conductor to the safetyground.Ground Fault Circuit Interrupters (GFCI)：Installations in Recreational Vehicles (for North American approvals) willrequire GFCI protection of all branch circuit connected to the AC output ofthe hardwire terminal equipped Inverter. In addition, electrical codesrequire GFCI protection of certain receptacles in residential installations.While the pure sine wave output of the Inverter is equivalent to thewaveform provided by utilities, compliance with UL standards requires us to test and recommend specific GFCI.Cotek has tested the following GFCI – protected 20A receptacles and found that they functioned properly when connected to the output of the Inverter.3-7. Inverter Operation：To operate the power inverter, turn the main switch ON. The power inverter is now ready to deliver AC power to your loads. If there is several loads use, turn them on separately after the inverter has been “ON” in order to prevent the OVP present caused by the surge power.3-7-1. Set the power switch to the “ON” position and the buzzer will send out “Beep” sounds at the moment the inverter will do self-diagnosis,then the Power Status LED indicators will also appear various colors.Finally the buzzer will sound another “Beep” and the Power StatusLED indicators will turn to “Green” color, the inverter starts workingsuccessfully.3-7-2. Set the power switch to the OFF position, the inverter stops and all the lights that are On, go Off.3-7-3. Set power inverter switch to the ON position and turn the test load On. The inverter should supply power to the load. If you plan toaccurately measure the true output r.m.s. voltage of inverter, a metersuch ad FLUKE 45 BECKMAN 4410 or TRIPLETT 4200 must beused.4. Troubleshooting guide：Problems and Symptoms Possible Cause Solutions “No AC Power Output”STATUS illuminates the red LEDa. Blinking fast Over input voltage.( OVP ) Check input voltage. Reduce input voltage.b. Blinking slow. Low input voltage.( UVP ) Recharge battery. Check connections and cable.c. Blinking Intermittently. Thermal shutdown.( OTP ) Improve ventilation. Make sure ventilation openings in inverter are not obstructed. Reduce ambient temperature.d. Solid ON. Short circuit or Wiringerror.Overload.(OLP) Check AC wiring for short circuit. Reduce load.5. Maintenance：Very little maintenance is required to keep your inverter operating properly.You should clean the exterior of the unit periodically with a damp cloth toprevent accumulation of dust and dirt.At the same time, tighten the screws on the DC input terminals.6. Warranty：We warrant this product against defects in materials and workmanship for a period of 24 months from the date of purchase and will repair or replace any defective Power Inverter when directly returned, postage paid, to us.This warranty will be considered void if the unit has suffered any obviousphysical damage or alteration either internally or externally and does notcover damage arising from improper use such as plugging.The unit into an unsuitable power sources attempts to operate products with excessive power consumption requirements, or use in unsuitable environments.This is the only warranty that the company makes.No other warranties express or imply including warranties of merchantability and fitness for a particular purpose.Repair and replacement are your sole remedies and the company shall not be liable for damages, whether direct, incidental, special or consequential, even though caused by negligence or other fault.。

Stud ThyristorLine ThyristorSKT 100Features∙Hermetic metal case with glass insulator∙Threaded stud ISO M12 x 1,75 or ½” - 20 UNF 2A∙Interchangeable withinternational standard case Typical Applications *∙DC motor control(e.g. for machine tools)∙Controlled rectifiers(e.g. for battery charging)∙AC controllers(e.g. for temperature control) ∙Recommended snubbernetwork e.g. for V RMS≤ 400 V: R= 47 Ω/10 W, C = 0,22 µF1) Mounting with grease-like thermal compound or joint contact compound2) M12 x 1,75 is standard, “UNF” shou ld be added in description for ½” - 20 2A thread.e.g.: SKT 100/08 D UNFSKTV RSMVV RRM, V DRMVI TRMS = 175 A (maximum value for continuous operation)I TAV = 100 A (sin. 180; T c = 85 °C)500 400 SKT 100/04 D900 800 SKT 100/08 D1300 1200 SKT 100/12 E1500 1400 SKT 100/14 E1700 1600 SKT 100/16 E1900 1800 SKT 100/18 ESymbol Condition Values Units I TAVI DI RMSsin. 180 ; T C = 100 (85) °C2 x P1/120; T a = 50 °C; B2/B62 x P1/120F; T a = 40 °C; B2/B62 x P1/120; T a = 45 °C; W1C74 (100)125 / 176182 / 250146AAAA I TSM T vj = 25 °C ; 10 ms 2000 AT vj = 130 °C ; 10 ms 1750 A i2t T vj = 25 °C ; 8,3...10 ms 20000 A2s T vj = 130 °C ; 8,3...10 ms 15300 A2s V T T vj = 25 °C, I T = 300 A max. 1,75 V V T(TO)T vj = 130 °C max. 1 V r T T vj = 130 °C max. 2,4 mΩI DD; I RD T vj = 130 °C; V RD = V RRM; V DD = V DRM max. 30 mA t gdt grT vj = 25 °C; I G = 1A; di G/d t = 1 A/µsV D = 0,67 * V DRM12µsµs (d i/d t)cr(d V/d t)crt qI HI LT vj = 130 °CT vj = 130 °C; D (E)T vj = 130 °CT vj = 25 °C; typ. / maxT vj = 25 °C; typ. / maxmax. 50500 (1000)100150 / 250300 / 600A/µsV/µsµsmAmA V GTI GTV GDI GDT vj = 25 °C; d.c.T vj = 25 °C; d.c.T vj = 130 °C; d.c.T vj = 130 °C; d.c.min. 3min. 150max. 0,25max. 10VmAVmA R th(j-c)R th(j-c)R th(j-c)R th(c-s)T vjT stgcont.sin. 180rec. 1200,250,280,310,08-40...+130-55...+150K/WK/WK/WK/W°C°C V isol- V~ M S M12 or ½” - 20 UNF 10 Nm M12 or ½” - 20 UNF (lubricated)1)7,5 Nm a 5 * 9,81 m/s2 m approx. 100 g Case B5Fig. 1L Power dissipation vs. on-state current Fig. 2 Rated on-state current vs. case temperature Fig. 4 Transient thermal impedance vs. time Fig. 1R Power dissipation vs. ambient temperature Fig. 3 Recovered charge vs. current decrease Fig. 5 Thermal resistance vs. conduction angleFig. 6 On-state characteristicsFig. 7 Power dissipation vs. on-state current Fig. 8 Surge overload current vs. timeFig. 9 Gate trigger characteristicsDimensions in mmCase B5 (IEC 60191-2: A12MA, A12U; JEDEC: TO-209 (TO94))*IMPORTANT INFORMATION AND WARNINGSThe specifications of SEMIKRON products may not be considered as guarantee or assurance of product characteristics ("Beschaffenheitsgarantie"). The specifications of SEMIKRON products describe only the usual characteristics of products to be expected in typical applications, which may still vary depending on the specific application. Therefore, products must be tested for the respective application in advance. Application adjustments may be necessary. T he user of SEMIKRON products is responsible for the safety of their applications embedding SEMIKRON products and must take adequate safety measures to prevent the applications from causing a physical injury, fire or other problem if any of SEMIKRON product s become faulty. The user is responsible to make sure that the application design is compliant with all applicable laws, regulations, norms and standards. Except as otherwise explicitly approved by SEMIKRON in a written document signed by authorized representatives of SEMIKRON, SEMIKRON products may not be used in any applications where a failure of the product or any consequences of the use thereof can reasonably be expected to result in personal injury. No representation or warranty is given and no liability is assumed with respect to the accuracy, completeness and/or use of any information herein, including without limitation, warranties of non-infringement of intellectual property rights of any third party. SEMIKRON does not assume any liability arising out of the applications or use of any product; neither does it convey any license under its patent rights, copyrights, trade secrets or other intellectual property rights, nor the rights of others. SEMIKRON makes no representation or warranty of non-infringement or alleged noninfringement of intellectual property rights of any third party which may arise from applications. Due to technical requirements our products may contain dangerous substances. For information on the types in question please contact the nearest SEMIKRON sales office. This document supersedes and replaces all information previously supplied and may be superseded by updates. SEMIKRON reserves the right to make changes.。

用户指南安装使用前请仔阅读本说明书目录引言产品外观系统功能主要参数安装接线基本操作联网设置故障检修原装附件软件安装门禁软件考勤软件一、引言：感谢您使用本非接触式感应卡门禁考勤管理系统，在使用本系统之前，请您详细阅读本用户指南，并严格按照手册中的要求来操作。

此用户指南将介绍本系统主要功能及操作使用方法。

本门禁系统采用目前世界上先进的技术-非接触式感应卡技术（也称射频识别卡（RFID）技术，RFID卡具有全球卡号唯一、不易仿制的读写特性和安全性能。

RFID卡片不会产生使用磁卡时因磁头磨损、磁粉脱落、灰尘等影响所带来的麻烦，而且避免了接触式IC卡因芯片与读卡器外露而引起的沾污、接触不良和外物损伤而导致的读卡不良现象，RFID卡适应各种环境，经久耐用。

每一次感应卡读的信息，无论是否向电锁发出开锁指令，系统都自动记录下来，管理者可以通过计算机下载调阅门禁控制系统存储的信息资料，轻松查阅、打印所有的通行事件。

管理软件将根据此原始资料自动统计员工考勤情况、编制考勤报表。

本系统提供了一种智能化的出入口控制及考勤管理方式，适用于需要控制人员出入的通道、商务机构、政府机关、住宅小区等等。

二、产品外观：465604162465604162三、系统功能：1、存储容量达8000条通行记录，1000张用户卡及密码2、每天自由设定八个限制通行时段3、具备读卡开门、读卡加密码开门、读卡或密码开门三种方式4、内置、外接读卡器，可实时区分进入、外出人次数5、采用RS485总线联网通讯方式，布线简易实用，联网可达64台6、19,200Bps高速传输下载数据7、主要输入/输出功能：电锁、开门按钮、报警器、门磁、门铃8、管理软件集门禁、考勤、人事于一体9、管理软件界面人性化，操作简易，使用方便10、系统图示可导入电子地图，自由设定门的名称、位置11、实时显示通过人员的姓名、相片、卡号、编号等资料12、自定义考勤规则及班次设定等13、自动统计迟到、早退、缺勤的次数及时间14、考勤结果可打印成报表或按Excel导出,.四、主要参数：五、安装接线：1．接线示意图：注：不要带电安装接线；不要从控制器直接接锁，电锁直接由电源接出；2．接线说明：A、读卡器到控制器的线，建议用6芯屏蔽多股双绞网线（其中2芯备用），数据线Data1 Data0互为双绞。