球化率 Spheroidization rate(中英文对照)

1. charging mixture (配料)2. gas vent (通气孔)air vent (通气孔)3. alcohol base wash (酒精基涂模剂)4. alloy (合金)alloy cast iron (合金铸铁)5. anchor pin (定位销)6. annealing (退火)annealing furnace (退火炉)7. arc welding (电弧熔接)8. as cast (铸胚/毛胚铸件)9. atmospheric core / pencil core(砂心/ 增压/透气砂心)10. bath analysis (炉前分析)11. hand molding (手工造模)12. bending strength (抗弯强度)13. bending test (弯曲试验)14. binder (黏结剂)15. furan resin 夫喃树脂16. blow hole / gas hole (气孔) 17. Brinell hardness (布氏硬度)18. brittleness (脆性)19. broken casting at gate / riser or vent(铸件破损) 去除浇口, 冒口, 溢流口时 , 一起将铸件主体部分也去除的破坏缺陷20. case hardening (表面硬化)21. pouring / pour / cast (浇铸/浇注)22. castability (铸造性)23. casting design / casting plan ( 铸造方案)24. cast iron / iron castings (铸铁)25. cavity (缩孔)26. ceramic core (陶瓷砂心)27. ceramic filter (陶瓷过滤片)28. ceramic tube (陶管)29. chaplet (砂心撑)30. chill (冷硬/冷激)31. chiller / densener (冷铁)32. chunky graphite (块状/短小石墨)33. clay (黏土)34. riser(冒口)35. coat/mold wash/facing material (涂料/涂模剂)36. washing / coating (涂模/上涂料)37. cold junction (冷接点)38. composites / composite material ( 复合材料)sand mill / sand mixer ( 混砂机)sand mixing (练砂)sand mold (砂模)39. contraction / shrinkage (收缩/缩孔/疏松)40. conveyor (输送机)41. core assemble (组合砂心)44. core box (砂心盒)45. core grid / rodding ( 砂心骨)46. core making machine ( 砂心机)47. lifting / raised mold / core raise ( 砂心上浮)48. core washing (砂心涂料)49. corrosion (腐蚀)50. crack (裂痕)=龟裂51. crystal (晶体)52. curing (硬化)53. cut (冲砂)=冲蚀54. metallic pattern (金属模)55. galvanizing (镀锌)56 . dirt / scum / dross / slag ( 熔渣 / 浮渣 / 炉渣)57. sprue / down sprue / down gate (下浇道 /竖浇道)58. draft (拔模斜度)59. drag (下模/下砂箱/下模箱)60. dressing / cleaning (上涂料/涂料/清理)61. electric furnace (电炉)62. electron microscope (电子显微镜)63. elongation (伸长/伸长率)64. etching solution/etching agent/etchingreagent (浸蚀液)65. open shrinkage / external shrinkage (外缩孔)66. ferritic spheroidal graphite cast iron(肥粒体球状石墨铸铁)67. ferrite (肥粒铁) 68. machining allowance / finishing allowance(加工余量)69. flake graphite cast iron ( 片状石墨铸铁)70. flow chart (流程图)71. CE meter (热分析)72. full size /full dimension (全尺寸)73. graphitic carbon / graphite carbon ( 石墨碳)74. gray cast iron (灰口铸铁/普通铸铁/片状石墨铸铁)75. green sand mold (湿砂模)76. hardener / hardening agent ( 硬化剂)77. hardness test (硬度试验)78. high frequency electric induction furnace ( 高周波感应电炉)79. holding furnace (保温炉)80. impact test (冲击试验)81. Charpy impact test (夏比冲击试验)82. impact value (冲击值)83. indirect chiller (间接冷铁)84. inlet / pouring basin / pouring cup ( 浇杯)85. Inoculant (接种剂)86. Inoculation (接种)87. ladle (浇包/浇桶/铁水包)88. molding flask (砂箱)89. joint surface (合模面)90. keel block (Y 型试块)91. knock-out / shake-out (清箱/开箱)92. low frequency induction furnace ( 低周波感应电炉)93. liquid penetrant testing (渗透探伤试验/PTtest)94. low temperature annealing ( 低温退火)95. magnetic powder test (MT/ 磁粉探伤)96. melting furnace (熔解炉)97. metal flask (金属砂箱)98. metallographic microscope ( 金相显微镜)99. metallography (金相学)100. parting line (分模线).101. parting plane (分割面)102. pattern (模型/模具)103. pattern coating (模型涂漆)104. pearlite (波来铁)105. burn on / sand burning ( 烧结/结砂) 106. pig iron (生铁)107. scrap steel (废钢)108. pin hole (针孔)109. pore (气孔)110. porosity (多孔性/气孔率)111. pouring rate (浇铸速度)112. pouring temperature (浇注温度)113. pouring time ( 浇注时间)114. pouring weight ( 浇注重量)115. quality control ( 质量管理)116. X-ray inspection / radiography (X 线探伤) 117. rapping (起模)118. ratio of graphite spheroidization ( 球化率) 119. rejected castings (不良品)120. residual stress (残留应力/铸造应力) 121. roll over machine ( 翻转机)122. sag core (砂心下垂) 123. sand blast (喷砂)124. sand inclusion ( 夹砂)125. short pours / short run ( 浇注不足)126. shot blast (抛丸)127. shrinkage cavity ( 缩孔)128. shrinkage crack (缩裂)129.slag off agent / slag disposal agent ( 除渣剂)130.slag inclusion (夹渣)131.solidification time (凝固时间)132.spherodial graphite (球状石墨)133.spheroidizing agent (球化剂)134. strength test (强度试验)135. stress concentration ( 应力集中)136. stress relief (应力消除)137. rough surface (表面粗糙)138. surface fold / gas run ( 皱皮/流缝/冷隔)139. surface roughness ( 表面粗糙度)140. surface treatment ( 表面处理)141. tensile strength ( 抗拉强度)142. tensile test (拉伸试验)143. test piece/test lug ( 试片)144. used sand (旧砂)145. working reference point ( 加工基准)146. Ultrasonic testing (UT/超声波检测)147. Gating system (浇注系统)148. test coupon (试棒)149. Non-destructive testing (NDT/非破坏性测试)150. Visual inspection (VT/ 目测)151. rough machining (粗加工)152. finishing machining (精加工)153. Non conformity report (NCR 不符合报告)154. Corrective action report ( 改善措施报告)155. solidification simulation ( 凝固模拟)。

English 中文释义A.C magnetic saturation 交流磁饱和Absorbed dose 吸收剂量Absorbed dose rate 吸收剂量率Acceptanc limits 验收范围Acceptance level 验收水平Acceptance standard 验收标准Accumulation test 累积检测Acoustic emission count（emission count）声发射计数（发射计数） Acoustic emission transducer 声发射换能器（声发射传感器）Acoustic emission(AE) 声发射Acoustic holography 声全息术Acoustic impedance 声阻抗Acoustic impedance matching 声阻抗匹配Acoustic impedance method 声阻法Acoustic wave 声波Acoustical lens 声透镜Acoustic—ultrasonic 声-超声（AU）Activation 活化Activity 活度Adequate shielding 安全屏蔽Ampere turns 安匝数Amplitude 幅度Angle beam method 斜射法Angle of incidence 入射角Angle of reflection 反射角Angle of spread 指向角Angle of squint 偏向角Angle probe 斜探头Angstrom unit 埃(A)Area amplitude response curve 面积幅度曲线Area of interest 评定区Arliflcial disconlinuity 人工不连续性Artifact 假缺陷Artificial defect 人工缺陷Artificial discontinuity 标准人工缺陷A-scan A 型扫描A-scope; A-scan A 型显示Attenuation coefficient 衰减系数Attenuator 衰减器Audible leak indicator 音响泄漏指示器Automatic testing 自动检测Autoradiography 自射线照片Avaluation 评定Barium concrete 钡混凝土Barn 靶Base fog 片基灰雾Bath 槽液Bayard- Alpert ionization gage B- A 型电离计Beam 声束Beam ratio 光束比Beam angle 束张角Beam axis 声束轴线Beam index 声束入射点Beam path location 声程定位Beam path; path length 声程Beam spread 声束扩散Betatron 电子感应加速器Bimetallic strip gage 双金属片计Bipolar field 双极磁场Black light filter 黑光滤波器Black light; ultraviolet radiation 黑光Blackbody 黑体Blackbody equivalent temperature 黑体等效温度 Bleakney mass spectrometer 波利克尼质谱仪Bleedout 渗出Bottom echo 底面回波Bottom surface 底面Boundary echo(first) 边界一次回波Bremsstrahlung 轫致辐射Broad-beam condition 宽射束Brush application 刷涂B-scan presenfation B 型扫描显示B-scope; B-scan B 型显示C- scan C 型扫描Calibration,instrument 设备校准Capillary action 毛细管作用Carrier fluid 载液Carry over of penetrate 渗透剂移转Cassette 暗合Cathode 阴极Central conductor method 中心导体法Characteristic curve 特性曲线Characteristic curve of film 胶片特性曲线Characteristic radiation 特征辐射Chemical fog 化学灰雾Cine-radiography 射线(活动)电影摄影术Cintact pads 接触垫Circumferential coils 圆环线圈Circumferential field 周向磁场Circumferential magnetization method 周向磁化法Clean 清理Clean- up 清除Clearing time 定透时间Coercive force 矫顽力Coherence 相干性Coherence length 相干长度（谐波列长度）Coi1，test 测试线圈Coil size 线圈大小Coil spacing 线圈间距Coil technique 线圈技术Coil method 线圈法Coilreference 线圈参考Coincidence discrimination 符合鉴别Cold-cathode ionization gage 冷阴极电离计Collimator 准直器Collimation 准直Collimator 准直器Combined colour comtrast and fluorescent penetrant 着色荧光渗透剂 Compressed air drying 压缩空气干燥Compressional wave 压缩波Compton scatter 康普顿散射Continuous emission 连续发射Continuous linear array 连续线阵Continuous method 连续法Continuous spectrum 连续谱Continuous wave 连续波Contract stretch 对比度宽限Contrast 对比度Contrast agent 对比剂Contrast aid 反差剂Contrast sensitivity 对比灵敏度Control echo 监视回波Control echo 参考回波Couplant 耦合剂Coupling 耦合Coupling losses 耦合损失Cracking 裂解Creeping wave 爬波Critical angle 临界角Cross section 横截面Cross talk 串音Cross-drilled hole 横孔Crystal 晶片C-scope; C-scan C 型显示Curie point 居里点Curie temperature 居里温度Curie(Ci) 居里Current flow method 通电法Current induction method 电流感应法Current magnetization method 电流磁化法Cut－off level 截止电平Dead zone 盲区Decay curve 衰变曲线Decibel(dB) 分贝Defect 缺陷Defect resolution 缺陷分辨力Defect detection sensitivity 缺陷检出灵敏度Defect resolution 缺陷分辨力Definition 清晰度Definition， image definition 清晰度，图像清晰度Demagnetization 退磁Demagnetization factor 退磁因子Demagnetizer 退磁装置Densitometer 黑度计Density 黑度（底片）Density comparison strip 黑度比较片Detecting medium 检验介质Detergent remover 洗净液Developer 显像剂Developer， agueons 水性显象剂Developer， dry 干显象剂Developer， liquid film 液膜显象剂Developer， nonaqueous （sus- pendible）非水（可悬浮）显象剂 Developing time 显像时间Development 显影Diffraction mottle 衍射斑Diffuse indications 松散指示Diffusion 扩散Digital image acquisition system 数字图像识别系统Dilatational wave 膨胀波Dip and drain station 浸渍和流滴工位Direct contact magnetization 直接接触磁化Direct exposure imaging 直接曝光成像Direct contact method 直接接触法Directivity 指向性Discontinuity 不连续性Distance- gain- size-German A VG 距离- 增益- 尺寸（DGS 德文为A VG） Distance marker; time marker 距离刻度Dose equivalent 剂量当量Dose rate meter 剂量率计Dosemeter 剂量计Double crystal probe 双晶片探头Double probe technique 双探头法Double transceiver technique 双发双收法Double traverse technique 二次波法Dragout 带出Drain time 滴落时间Drain time 流滴时间Drift 漂移Dry method 干法Dry powder 干粉Dry technique 干粉技术Dry developer 干显像剂Dry developing cabinet 干显像柜Dry method 干粉法Drying oven 干燥箱Drying station 干燥工位Drying time 干燥时间D-scope; D-scan D 型显示Dual search unit 双探头Dual-focus tube 双焦点管Duplex-wire image quality indicator 双线像质指示器Duration 持续时间Dwell time 停留时间Dye penetrant 着色渗透剂Dynamic leak test 动态泄漏检测Dynamic leakage measurement 动态泄漏测量Dynamic range 动态范围Dynamic radiography 动态射线透照术Echo 回波Echo frequency 回波频率Echo height 回波高度Echo indication 回波指示Echo transmittance of sound pressure 往复透过率Echo width 回波宽度Eddy current 涡流Eddy current flaw detector 涡流探伤仪Eddy current testiog 涡流检测Edge 端面Edge effect 边缘效应Edge echo 棱边回波Edge effect 边缘效应Effective depth penetration （EDP）有效穿透深度Effective focus size 有效焦点尺寸Effective magnetic permeability 有效磁导率Effective permeability 有效磁导率Effective reflection surface of flaw 缺陷有效反射面Effective resistance 有效电阻Elastic medium 弹性介质Electric displacement 电位移Electrical center 电中心Electrode 电极Electromagnet 电磁铁Electro-magnetic acoustic transducer 电磁声换能器Electromagnetic induction 电磁感应Electromagnetic radiation 电磁辐射Electromagnetic testing 电磁检测Electro-mechanical coupling factor 机电耦合系数Electron radiography 电子辐射照相术Electron volt 电子伏恃Electronic noise 电子噪声Electrostatic spraying 静电喷涂Emulsification 乳化Emulsification time 乳化时间Emulsifier 乳化剂Encircling coils 环绕式线圈End effect 端部效应Energizing cycle 激励周期Equalizing filter 均衡滤波器Equivalent 当量Equivalent I．Q. I. Sensitivity 象质指示器当量灵敏度 Equivalent nitrogen pressure 等效氮压Equivalent penetrameter sensifivty 透度计当量灵敏度 Equivalent method 当量法Erasabl optical medium 可探光学介质Etching 浸蚀Evaluation 评定Evaluation threshold 评价阈值Event count 事件计数Event count rate 事件计数率Examination area 检测范围Examination region 检验区域Exhaust pressure/discharge pressure 排气压力Exhaust tubulation 排气管道Expanded time-base sweep 时基线展宽Exposure 曝光Exposure table 曝光表格Exposure chart 曝光曲线Exposure fog 曝光灰雾Exposure，radiographic exposure 曝光，射线照相曝光 Extended source 扩展源Facility scattered neutrons 条件散射中子False indication 假指示Family 族Far field 远场Feed-through coil 穿过式线圈Field， resultant magnetic 复合磁场Fill factor 填充系数Film speed 胶片速度Film badge 胶片襟章剂量计Film base 片基Film contrast 胶片对比度Film gamma 胶片γ值Film processing 胶片冲洗加工Film speed 胶片感光度Film unsharpness 胶片不清晰度Film viewing screen 观察屏Filter 滤波器/滤光板Final test 复探Flat-bottomed hole 平底孔Flat-bottomed hole equivalent 平底孔当量Flaw 伤Flaw characterization 伤特性Flaw echo 缺陷回波Flexural wave 弯曲波Floating threshold 浮动阀值Fluorescence 荧光Fluorescent examination method 荧光检验法Fluorescent magnetic particle inspection 荧光磁粉检验 Fluorescent dry deposit penetrant 干沉积荧光渗透剂Fluorescent light 荧光Fluorescent magnetic powder 荧光磁粉Fluorescent penetrant 荧光渗透剂Fluorescent screen 荧光屏Fluoroscopy 荧光检查法Flux leakage field 磁通泄漏场Flux lines 磁通线Focal spot 焦点Focal distance 焦距Focus length 焦点长度Focus size 焦点尺寸Focus width 焦点宽度Focus(electron) 电子焦点Focused beam 聚焦声束Focusing probe 聚焦探头Focus-to-film distance(f.f.d) 焦点-胶片距离（焦距） Fog 底片灰雾Fog density 灰雾密度Footcandle 英尺烛光Freguency 频率Frequency constant 频率常数Fringe 干涉带Front distance 前沿距离Front distance of flaw 缺陷前沿距离Full- wave direct current（FWDC）全波直流Fundamental frequency 基频Furring 毛状迹痕Gage pressure 表压Gain 增益Gamma radiography γ射线透照术Gamma ray source γ射线源Gamma ray source container γ射线源容器Gamma rays γ射线Gamma-ray radiographic equipment γ射线透照装置 Gap scanning 间隙扫查Gas 气体Gate 闸门Gating technique 选通技术Gauss 高斯Geiger-Muller counter 盖革.弥勒计数器Geometric unsharpness 几何不清晰度Gray(Gy) 戈瑞Grazing incidence 掠入射Grazing angle 掠射角Group velocity 群速度Half life 半衰期Half- wave current （HW）半波电流Half-value layer(HVL) 半值层Half-value method 半波高度法Halogen 卤素Halogen leak detector 卤素检漏仪Hard X-rays 硬X 射线Hard-faced probe 硬膜探头Harmonic analysis 谐波分析Harmonic distortion 谐波畸变Harmonics 谐频Head wave 头波Helium bombing 氦轰击法Helium drift 氦漂移Helium leak detector 氦检漏仪Hermetically tight seal 气密密封High vacuum 高真空High energy X-rays 高能X 射线Holography (optical) 光全息照相Holography， acoustic 声全息Hydrophilic emulsifier 亲水性乳化剂Hydrophilic remover 亲水性洗净剂Hydrostatic text 流体静力检测Hysteresis 磁滞Hysteresis 磁滞IACS IACSID coil ID 线圈Image definition 图像清晰度Image contrast 图像对比度Image enhancement 图像增强Image magnification 图像放大Image quality 图像质量Image quality indicator sensitivity 像质指示器灵敏度Image quality indicator(IQI)/image quality indication 像质指示器 Imaging line scanner 图像线扫描器Immersion probe 液浸探头Immersion rinse 浸没清洗Immersion testing 液浸法Immersion time 浸没时间Impedance 阻抗Impedance plane diagram 阻抗平面图Imperfection 不完整性Impulse eddy current testing 脉冲涡流检测Incremental permeability 增量磁导率Indicated defect area 缺陷指示面积Indicated defect length 缺陷指示长度Indication 指示Indirect exposure 间接曝光Indirect magnetization 间接磁化Indirect magnetization method 间接磁化法Indirect scan 间接扫查Induced field 感应磁场Induced current method 感应电流法Infrared imaging system 红外成象系统Infrared sensing device 红外扫描器Inherent fluorescence 固有荧光Inherent filtration 固有滤波Initial permeability 起始磁导率Initial pulse 始脉冲Initial pulse width 始波宽度Inserted coil 插入式线圈Inside coil 内部线圈Inside- out testing 外泄检测Inspection 检查Inspection medium 检查介质Inspection frequency/ test frequency 检测频率Intensifying factor 增感系数Intensifying screen 增感屏Interal,arrival time （Δtij)/arrival time interval（Δtij）到达时间差(Δtij) Interface boundary 界面Interface echo 界面回波Interface trigger 界面触发Interference 干涉Interpretation 解释Ion pump 离子泵Ion source 离子源Ionization chamber 电离室Ionization potential 电离电位Ionization vacuum gage 电离真空计Ionography 电离射线透照术Irradiance， E 辐射通量密度， EIsolation 隔离检测Isotope 同位素Kaiser effect 凯塞(Kaiser)效应Kilo volt kv 千伏特Kiloelectron volt keV 千电子伏特Krypton 85 氪85L／D ratio L/D 比Lamb wave 兰姆波Latent image 潜象Lateral scan 左右扫查Lateral scan with oblique angle 斜平行扫查Latitude (of an emulsion) 胶片宽容度Lead screen 铅屏Leak 泄漏孔Leak artifact 泄漏器Leak detector 检漏仪Leak testtion 泄漏检测Leakage field 泄漏磁场Leakage rate 泄漏率Leechs 磁吸盘Lift-off effect 提离效应Light intensity 光强度Limiting resolution 极限分辨率Line scanner 线扫描器Line focus 线焦点Line pair pattern 线对检测图Line pairs per millimetre 每毫米线对数Linear (electron) accelerator(LINAC) 电子直线加速器 Linear attenuation coefficient 线衰减系数Linear scan 线扫查Linearity （time or distance）线性（时间或距离） Linearity， anplitude 幅度线性Lines of force 磁力线Lipophilic emulsifier 亲油性乳化剂Lipophilic remover 亲油性洗净剂Liquid penetrant examination 液体渗透检验Liquid film developer 液膜显像剂Local magnetization 局部磁化Local magnetization method 局部磁化法Local scan 局部扫查Localizing cone 定域喇叭筒Location 定位Location accuracy 定位精度Location computed 定位，计算Location marker 定位标记Location upon delta-T 时差定位Location， clusfer 定位，群集Location，continuous AE signal 定位，连续AE 信号 Longitudinal field 纵向磁场Longitudinal magnetization method 纵向磁化法Longitudinal resolution 纵向分辨率Longitudinal wave 纵波Longitudinal wave probe 纵波探头Longitudinal wave technique 纵波法Loss of back reflection 背面反射损失Loss of back reflection 底面反射损失Love wave 乐甫波Low energy gamma radiation 低能γ辐射Low－enerugy photon radiation 低能光子辐射Luminance 亮度Luminosity 流明Lusec 流西克Maga or million electron volts MeV 兆电子伏特Magnetic history 磁化史Magnetic hysteresis 磁性滞后Magnetic particle field indication 磁粉磁场指示器Magnetic particle inspection flaw indications 磁粉检验的伤显示 Magnetic circuit 磁路Magnetic domain 磁畴Magnetic field distribution 磁场分布Magnetic field indicator 磁场指示器Magnetic field meter 磁场计Magnetic field strength 磁场强度(H)Magnetic field/field，magnetic 磁场Magnetic flux 磁通Magnetic flux density 磁通密度Magnetic force 磁化力Magnetic leakage field 漏磁场Magnetic leakage flux 漏磁通Magnetic moment 磁矩Magnetic particle 磁粉Magnetic particle indication 磁痕Magnetic particle testing/magnetic particle examination 磁粉检测 Magnetic permeability 磁导率Magnetic permeability 磁导率Magnetic pole 磁极Magnetic saturataion 磁饱和Magnetic saturation 磁饱和Magnetic writing 磁写Magnetizing 磁化Magnetizing current 磁化电流Magnetizing coil 磁化线圈Magnetostrictive effect 磁致伸缩效应Magnetostrictive transducer 磁致伸缩换能器Main beam 主声束Manual testing 手动检测Markers 时标MA-scope; MA-scan MA 型显示Masking 遮蔽Mass attcnuation coefficient 质量吸收系数Mass number 质量数Mass spectrometer （M.S.）质谱仪Mass spectrometer leak detector 质谱检漏仪Mass spectrum 质谱Master/slave discrimination 主从鉴别MDTD 最小可测温度差Mean free path 平均自由程Medium vacuum 中真空Mega or million volt MV 兆伏特Micro focus X - ray tube 微焦点X 光管Microfocus radiography 微焦点射线透照术Micrometre 微米Micron of mercury 微米汞柱Microtron 电子回旋加速器Milliampere 毫安（mA）Millimetre of mercury 毫米汞柱Minifocus x- ray tube 小焦点调射线管Minimum detectable leakage rate 最小可探泄漏率Minimum resolvable temperature difference （MRTD）最小可分辨温度差（MRDT）Mode 波型Mode conversion 波型转换Mode transformation 波型转换Moderator 慢化器Modulation transfer function （MTF）调制转换功能（MTF）Modulation analysis 调制分析Molecular flow 分子流Molecular leak 分子泄漏Monitor 监控器Monochromatic 单色波Movement unsharpness 移动不清晰度Moving beam radiography 可动射束射线透照术Multiaspect magnetization method 多向磁化法Multidirectional magnetization 多向磁化Multifrequency eddy current testiog 多频涡流检测Multiple back reflections 多次背面反射Multiple reflections 多次反射Multiple back reflections 多次底面反射Multiple echo method 多次反射法Multiple probe technique 多探头法Multiple triangular array 多三角形阵列Narrow beam condition 窄射束NC NCNear field 近场Near field length 近场长度Near surface defect 近表面缺陷Net density 净黑度Net density 净(光学)密度Neutron 中子Neutron radiograhy 中子射线透照Neutron radiography 中子射线透照术Newton （N）牛顿Nier mass spectrometer 尼尔质谱仪Noise 噪声Noise 噪声Noise equivalent temperature difference （NETD）噪声当量温度差（NETD） Nominal angle 标称角度Nominal frequency 标称频率Non-aqueous liquid developer 非水性液体显像剂Noncondensable gas 非冷凝气体Nondcstructivc Examination（NDE）无损试验Nondestructive Evaluation（NDE）无损评价Nondestructive Inspection（NDI）无损检验Nondestructive Testing（NDT）无损检测Nonerasble optical data 可固定光学数据Nonferromugnetic material 非铁磁性材料Nonrelevant indication 非相关指示Non-screen-type film 非增感型胶片Normal incidence 垂直入射（亦见直射声束）Normal permeability 标准磁导率Normal beam method; straight beam method 垂直法Normal probe 直探头Normalized reactance 归一化电抗Normalized resistance 归一化电阻Nuclear activity 核活性Nuclide 核素Object plane resolution 物体平面分辨率Object scattered neutrons 物体散射中子Object beam 物体光束Object beam angle 物体光束角Object-film distance 被检体-胶片距离Object 一film distance 物体- 胶片距离Over development 显影过度Over emulsfication 过乳化Overall magnetization 整体磁化Overload recovery time 过载恢复时间Overwashing 过洗Oxidation fog 氧化灰雾P PPair production 偶生成Pair production 电子对产生Pair production 电子偶的产生Palladium barrier leak detector 钯屏检漏仪Panoramic exposure 全景曝光Parallel scan 平行扫查Paramagnetic material 顺磁性材料Parasitic echo 干扰回波Partial pressure 分压Particle content 磁悬液浓度Particle velocity 质点(振动)速度Pascal （Pa）帕斯卡（帕）Pascal cubic metres per second 帕立方米每秒（Pa?m3/s ） Path length 光程长Path length difference 光程长度差Pattern 探伤图形Peak current 峰值电流Penetrameter 透度计Penetrameter sensitivity 透度计灵敏度Penetrant 渗透剂Penetrant comparator 渗透对比试块Penetrant flaw detection 渗透探伤Penetrant removal 渗透剂去除Penetrant station 渗透工位Penetrant， water- washable 水洗型渗透剂Penetration 穿透深度Penetration time 渗透时间Permanent magnet 永久磁铁Permeability coefficient 透气系数Permeability，a-c 交流磁导率Permeability，d－c 直流磁导率Phantom echo 幻象回波Phase analysis 相位分析Phase angle 相位角Phase controlled circuit breaker 断电相位控制器Phase detection 相位检测Phase hologram 相位全息Phase sensitive detector 相敏检波器Phase shift 相位移Phase velocity 相速度Phase-sensitive system 相敏系统Phillips ionization gage 菲利浦电离计Phosphor 荧光物质Photo fluorography 荧光照相术Photoelectric absorption 光电吸收Photographic emulsion 照相乳剂Photographic fog 照相灰雾Photostimulable luminescence 光敏发光Piezoelectric effect 压电效应Piezoelectric material 压电材料Piezoelectric stiffness constant 压电劲度常数 Piezoelectric stress constant 压电应力常数 Piezoelectric transducer 压电换能器Piezoelectric voltage constant 压电电压常数 Pirani gage 皮拉尼计Pirani gage 皮拉尼计Pitch and catch technique 一发一收法Pixel 象素Pixel size 象素尺寸Pixel， disply size 象素显示尺寸Planar array 平面阵(列)Plane wave 平面波Plate wave 板波Plate wave technique 板波法Point source 点源Post emulsification 后乳化Post emulsifiable penetrant 后乳化渗透剂Post-cleaning 后清除Post-cleaning 后清洗Powder 粉未Powder blower 喷粉器Powder blower 磁粉喷枪Pre-cleaning 预清理Pressure difference 压力差Pressure dye test 压力着色检测Pressure probe 压力探头Pressure testing 压力检测Pressure- evacuation test 压力抽空检测Pressure mark 压痕Pressure,design 设计压力Pre-test 初探Primary coil 一次线圈Primary radiation 初级辐射Probe gas 探头气体Probe test 探头检测Probe backing 探头背衬Probe coil 点式线圈Probe coil 探头式线圈Probe coil clearance 探头线圈间隙Probe index 探头入射点Probe to weld distance 探头-焊缝距离Probe/ search unit 探头Process control radiograph 工艺过程控制的射线照相Processing capacity 处理能力Processing speed 处理速度Prods 触头Projective radiography 投影射线透照术Proportioning probe 比例探头Protective material 防护材料Proton radiography 质子射线透照Pulse 脉冲波Pulse 脉冲Pulse echo method 脉冲回波法Pulse repetition rate 脉冲重复率Pulse amplitude 脉冲幅度Pulse echo method 脉冲反射法Pulse energy 脉冲能量Pulse envelope 脉冲包络Pulse length 脉冲长度Pulse repetition frequency 脉冲重复频率Pulse tuning 脉冲调谐Pump- out tubulation 抽气管道Pump-down time 抽气时间Q factor Q 值Quadruple traverse technique 四次波法Quality (of a beam of radiation) 射线束的质Quality factor 品质因数Quenching 阻塞Quenching of fluorescence 荧光的猝灭Quick break 快速断间Rad(rad) 拉德Radiance， L 面辐射率，LRadiant existence， M 幅射照度MRadiant flux； radiant power，ψe辐射通量、辐射功率、ψe Radiation 辐射Radiation does 辐射剂量Radio frequency （r- f） display 射频显示Radio- frequency mass spectrometer 射频质谱仪Radio frequency(r-f) display 射频显示Radiograph 射线底片Radiographic contrast 射线照片对比度Radiographic equivalence factor 射线照相等效系数Radiographic exposure 射线照相曝光量Radiographic inspection 射线检测Radiographic inspection 射线照相检验Radiographic quality 射线照相质量Radiographic sensitivity 射线照相灵敏度Radiographic contrast 射线底片对比度Radiographic equivalence factor 射线透照等效因子 Radiographic inspection 射线透照检查Radiographic quality 射线透照质量Radiographic sensitivity 射线透照灵敏度Radiography 射线照相术Radiological examination 射线检验Radiology 射线学Radiometer 辐射计Radiometry 辐射测量术Radioscopy 射线检查法Range 量程Rayleigh wave 瑞利波Rayleigh scattering 瑞利散射Real image 实时图像Real-time radioscopy 实时射线检查法Rearm delay time 重新准备延时时间Rearm delay time 重新进入工作状态延迟时间Reciprocity failure 倒易律失效Reciprocity law 倒易律Recording medium 记录介质Recovery time 恢复时间Rectified alternating current 脉动直流电Reference block 参考试块Reference beam 参考光束Reference block 对比试块Reference block method 对比试块法eference coil 参考线圈Reference line method 基准线法Reference standard 参考标准Reflection 反射Reflection coefficient 反射系数Reflection density 反射密度Reflector 反射体Refraction 折射Refractive index 折射率Refrence beam angle 参考光束角Reicnlbation 网纹Reject; suppression 抑制Rejection level 拒收水平Relative permeability 相对磁导率Relevant indication 相关指示Reluctance 磁阻Rem(rem) 雷姆Remote controlled testing 机械化检测Replenisers 补充剂Representative quality indicator 代表性质量指示器Residual magnetic field/field， residual magnetic 剩磁场 Residual technique 剩磁技术Residual magnetic method 剩磁法Residual magnetism 剩磁Resistance （to flow）气阻Resolution 分辨力Resonance method 共振法Response factor 响应系数Response time 响应时间Resultant field 复合磁场Resultant magnetic field 合成磁场Resultant magnetization method 组合磁化法Retentivity 顽磁性Reversal 反转现象Ring-down count 振铃计数Ring-down count rate 振铃计数率Rinse 清洗Rise time 上升时间Rise-time discrimination 上升时间鉴别Rod-anode tube 棒阳极管Roentgen(R) 伦琴Roof angle 屋顶角Rotational magnetic field 旋转磁场Rotational magnetic field method 旋转磁场法Rotational scan 转动扫查Roughing 低真空Roughing line 低真空管道Roughing pump 低真空泵S SSafelight 安全灯Sampling probe 取样探头Saturation 饱和Saturation，magnetic 磁饱和Saturation level 饱和电平Scan on grid lines 格子线扫查Scan pitch 扫查间距Scanning 扫查Scanning index 扫查标记Scanning directly on the weld 焊缝上扫查Scanning path 扫查轨迹Scanning sensitivity 扫查灵敏度Scanning speed 扫查速度Scanning zone 扫查区域Scattared energy 散射能量Scatter unsharpness 散射不清晰度Scattered neutrons 散射中子Scattered radiation 散射辐射Scattering 散射Schlieren system 施利伦系统Scintillation counter 闪烁计数器Scintillator and scintillating crystals 闪烁器和闪烁晶体 Screen 屏Screen unsharpness 荧光增感屏不清晰度Screen-type film 荧光增感型胶片SE probe SE 探头Search-gas 探测气体Second critical angle 第二临界角Secondary radiation 二次射线Secondary coil 二次线圈Secondary radiation 次级辐射Selectivity 选择性Semi-conductor detector 半导体探测器Sensitirity va1ue 灵敏度值Sensitivity 灵敏度Sensitivity of leak test 泄漏检测灵敏度Sensitivity control 灵敏度控制Shear wave 切变波Shear wave probe 横波探头Shear wave technique 横波法Shim 薄垫片Shot 冲击通电Side lobe 副瓣Side wall 侧面Sievert(Sv) 希(沃特)Signal 信号Signal gradient 信号梯度Signal over load point 信号过载点Signal overload level 信号过载电平Signal to noise ratio 信噪比Single crystal probe 单晶片探头Single probe technique 单探头法Single traverse technique 一次波法Sizing technique 定量法Skin depth 集肤深度Skin effect 集肤效应Skip distance 跨距Skip point 跨距点Sky shine(air scatter) 空中散射效应Sniffing probe 嗅吸探头Soft X-rays 软X 射线Soft-faced probe 软膜探头Solarization 负感作用Solenoid 螺线管Soluble developer 可溶显像剂Solvent remover 溶剂去除剂Solvent cleaners 溶剂清除剂Solvent developer 溶剂显像剂Solvent remover 溶剂洗净剂Solvent-removal penetrant 溶剂去除型渗透剂 Sorption 吸着Sound diffraction 声绕射Sound insulating layer 隔声层Sound intensity 声强Sound intensity level 声强级Sound pressure 声压Sound scattering 声散射Sound transparent layer 透声层Sound velocity 声速Source 源Source data label 放射源数据标签Source location 源定位Source size 源尺寸Source-film distance 射线源-胶片距离Spacial frequency 空间频率Spark coil leak detector 电火花线圈检漏仪 Specific activity 放射性比度Specified sensitivity 规定灵敏度Standard 标准Standard 标准试样Standard leak rate 标准泄漏率Standard leak 标准泄漏孔Standard tast block 标准试块Standardization instrument 设备标准化Standing wave; stationary wave 驻波Step wedge 阶梯楔块Step- wadge calibration film 阶梯楔块校准底片 Step- wadge comparison film 阶梯楔块比较底片 Step wedge 阶梯楔块Step-wedge calibration film 阶梯-楔块校准片Step-wedge comparison film 阶梯-楔块比较片 Stereo-radiography 立体射线透照术Subject contrast 被检体对比度Subsurface discontinuity 近表面不连续性Suppression 抑制Surface echo 表面回波Surface field 表面磁场Surface noise 表面噪声Surface wave 表面波Surface wave probe 表面波探头Surface wave technique 表面波法Surge magnetization 脉动磁化Surplus sensitivity 灵敏度余量Suspension 磁悬液Sweep 扫描Sweep range 扫描范围Sweep speed 扫描速度Swept gain 扫描增益Swivel scan 环绕扫查System exanlillatien threshold 系统检验阈值System inclacel artifacts 系统感生物System noise 系统噪声Tackground， target 目标本底Tandem scan 串列扫查Target 耙Target 靶Television fluoroscopy 电视X 射线荧光检查Temperature envelope 温度范围Tenth-value-layer(TVL) 十分之一值层Test coil 检测线圈Test quality level 检测质量水平Test ring 试环Test block 试块Test frequency 试验频率Test piece 试片Test range 探测范围Test surface 探测面Testing，ulrasonic 超声检测Thermal neutrons 热中子Thermocouple gage 热电偶计Thermogram 热谱图Thermography， infrared 红外热成象Thermoluminescent dosemeter(TLD) 热释光剂量计Thickness sensitivity 厚度灵敏度Third critiical angle 第三临界角Thixotropic penetrant 摇溶渗透剂Thormal resolution 热分辨率Threading bar 穿棒Three way sort 三档分选Threshold setting 门限设置Threshold fog 阈值灰雾Threshold level 阀值Threshotd tcnet 门限电平Throttling 节流Through transmission technique 穿透技术Through penetration technique 贯穿渗透法Through transmission technique; transmission technique 穿透法 Through-coil technique 穿过式线圈技术Throughput 通气量Tight 密封Total reflection 全反射Totel image unsharpness 总的图像不清晰度Tracer probe leak location 示踪探头泄漏定位Tracer gas 示踪气体Transducer 换能器/传感器Transition flow 过渡流Translucent base media 半透明载体介质Transmission 透射Transmission densitomefer 发射密度计Transmission coefficient 透射系数Transmission point 透射点Transmission technique 透射技术Transmittance，τ透射率τTransmitted film density 检测底片黑度Transmitted pulse 发射脉冲Transverse resolution 横向分辨率Transverse wave 横波Traveling echo 游动回波Travering scan; depth scan 前后扫查Triangular array 正三角形阵列Trigger/alarm condition 触发/报警状态Trigger/alarm level 触发/报警标准Triple traverse technique 三次波法True continuous technique 准确连续法技术 Trueattenuation 真实衰减Tube current 管电流Tube head 管头Tube shield 管罩Tube shutter 管子光闸Tube window 管窗Tube-shift radiography 管子移位射线透照术 Two-way sort 两档分选Ultra- high vacuum 超高真空Ultrasonic leak detector 超声波检漏仪Ultrasonic noise level 超声噪声电平Ultrasonic cleaning 超声波清洗Ultrasonic field 超声场Ultrasonic flaw detection 超声探伤Ultrasonic flaw detector 超声探伤仪Ultrasonic microscope 超声显微镜Ultrasonic spectroscopy 超声频谱Ultrasonic testing system 超声检测系统Ultrasonic thickness gauge 超声测厚仪Ultraviolet radiation 紫外辐射Under development 显影不足Unsharpness 不清晰Useful density range 有效光学密度范围UV-A A 类紫外辐射UV-A filter A 类紫外辐射滤片Vacuum 真空Vacuum cassette 真空暗盒Vacuum testing 真空检测Vacuum cassette 真空暗合Van de Graaff generator 范德格喇夫起电机 Vapor pressure 蒸汽压Vapour degreasing 蒸汽除油Variable angle probe 可变角探头Vee path V 型行程Vehicle 载体Vertical linearity 垂直线性Vertical location 垂直定位Visible light 可见光Vitua limage 虚假图像V oltage threshold 电压阈值V oltage threshold 阈值电压Wash station 水洗工位Water break test 水膜破坏试验Water column coupling method 水柱耦合法 Water column probe 水柱耦合探头Water path; water distance 水程Water tolerance 水容限Water-washable penetrant 可水洗型渗透剂Wave 波Wave guide acoustic emission 声发射波导杆 Wave train 波列Wave from 波形Wave front 波前Wave length 波长Wave node 波节Wave train 波列Wedge 斜楔Wet slurry technique 湿软磁膏技术Wet technique 湿法技术Wet method 湿粉法Wetting action 润湿作用Wetting action 润湿作用Wetting agents 润湿剂Wheel type probe; wheel search unit 轮式探头 White light 白光White X-rays 连续X 射线Wobble 摆动Wobble effect 抖动效应Working sensitivity 探伤灵敏度Wrap around 残响波干扰Xeroradiography 静电射线透照术X-radiation X 射线X-ray controller X 射线控制器X-ray detection apparatus X 射线探伤装置X-ray film 射线胶片X-ray paper X 射线感光纸X-ray tube X 射线管X-ray tube diaphragm X 射线管光阑Yoke 磁轭Yoke magnetization method 磁轭磁化法Zigzag scan 锯齿扫查Zone calibration location 时差区域校准定位 Zone location 区域定位。

质谱仪常用参数中英文对照质谱仪是一种广泛应用于化学、生物、环境等领域的仪器，用于分析和识别样品中的化合物。

以下是质谱仪常用参数的中英文对照及其解释。

1. Mass range（质量范围）：The range of masses that can be detected and measured by the mass spectrometer.（质谱仪可以检测和测量的质量范围。

）2. Mass resolution（质量分辨率）：The ability of a mass spectrometer to distinguish between two peaks with similar masses. It is defined as the ratio of the difference in mass between two ions to the width of the peak at a defined fraction (usually 10%) of the maximum height.（质谱仪区分两个质量相似的峰的能力。

它定义为两个离子之间质量差与峰半高宽度的比值（通常为最大高度的10%））3. Sensitivity（灵敏度）：The ability of a mass spectrometer to detect and quantify trace amounts of analytes in a sample.（质谱仪检测和定量样品中微量分析物的能力。

）4. Scan speed（扫描速度）：The speed at which a mass spectrometer can acquire a spectrum. It is usually expressed in scans per second.（质谱仪获取光谱的速度，通常以每秒扫描次数计算。

）5. Dynamic range（动态范围）：The ratio between the largest and smallest signals a mass spectrometer can measure. Itreflects the ability of the instrument to measure both low andhigh abundance ions.（质谱仪能够测量的最大和最小信号之间的比值。

coextrusion加工 processing 反应性加工 reactive processing 等离子体加工 plasma processing 加工性 processability 熔体流动指数 melt [flow] index 门尼粘度 Mooney index塑化 plasticizing 增塑作用 plasticization 内增塑作用internal plasticization 外增塑作用 externalplasticization 增塑溶胶 plastisol 增强 reinforcing 增容作用 compatibilization 相容性 compatibility 相溶性intermiscibility 生物相容性 biocompatibility 血液相容性blood compatibility 组织相容性 tissue compatibility 混炼 milling, mixing 素炼 mastication 塑炼 plastication 过炼 dead milled 橡胶配合 rubber compounding 共混blend 捏和 kneading 冷轧 cold rolling 压延性calenderability 压延 calendaring 埋置 embedding 压片 performing 模塑 molding 模压成型 compressionmolding 压缩成型 compression forming 冲压模塑impact moulding, shock moulding 叠模压塑 stackmoulding 复合成型 composite molding 注射成型injection molding 注塑压缩成型 injection compressionmolding 射流注塑 jet molding 无流道冷料注塑runnerless injection molding 共注塑 coinjectionmolding 气辅注塑 gas aided injection molding 注塑焊接 injection welding 传递成型 transfer molding树脂传递成型 resin transfer molding铸塑cast熔铸 fusion casting铸塑成型 cast molding单体浇铸 monomer casting挤出 extrusion多层挤塑 multi-layer extrusion共挤吹塑 coextrusion blow molding同轴挤塑 coaxial extrusion吹胀挤塑 blown extrusion挤出吹塑 extrusion blow molding 挤拉吹塑成型extrusion draw blow molding吹塑 blow molding多层吹塑 multi-layer blow molding 拉伸吹塑成型stretch blow molding 滚塑 rotational moulding反应注射成型reaction injection molding, RIM 真空成型vacuum forming无压成型zero ressure molding真空烧结vacuum sintering真空袋成型vacuum bag molding热成型thermal forming拉伸热成型stretch thermoforming袋模塑bag molding糊塑paste molding镶铸imbedding冲压成型impact molding触压成型impression molding层压材料laminate泡沫塑料成型foam molding包模成型drape molding充气吹胀inflation橡胶胶乳rubber latex胶乳latex高分子胶体polymer colloid生橡胶raw rubber ，crude rubber硬质胶ebonite再生胶reclaimed rubber充油橡胶oil-extended rubber母胶masterbatch硫化vulcanization后硫化post cure , post vulcanization 自硫［化］bin cure自交联self crosslinking , self curing过硫over cure返硫reversion欠硫under cure动态硫化dynamic vulcanization不均匀硫化heterogeneous vulcanization开始［硫化］效应set-up effect自动硫化self-curing, self-vulcanizing焦烧scorching无压硫化non-pressure cure模压硫化moulding curing常温硫化auto-vulcanization热硫化heat curing蒸汽硫化steam curing微波硫化micro wave curing辐射硫化radiation vulcanization辐射交联radiation crosslinking连续硫化continuous vulcanization无模硫化open vulcanization成纤fiber forming 可纺性spinnability 纺丝spinning 干纺dry spinning 湿纺wet spinning 干湿法纺丝dry wet spinning干喷湿法纺丝dry jet wet spinning溶液纺丝solution spinning孚L液纺丝emulsion spinning孚L液闪蒸纺丝法e mulsion flash spinning process喷射纺丝jet spinning喷纺成形spray spinning液晶纺丝liquid crystal spinning熔纺melt spinning共混纺丝blended spinning 凝胶纺［丝］gel spinning 反应纺丝reaction spinning静电纺丝electrostatic spinning高压纺丝high-pressure spinning复合纺丝conjugate spinning无纺布non-woven fabrics单丝monofilament, monofil复丝multifilament全取向丝fully oriented yarn中空纤维hollow fiber皮芯纤维sheath core fiber共纺cospinning冷拉伸cold drawing, cold stretching单轴拉伸uniaxial drawing ，uniaxial elongation双轴拉伸biaxial drawing多轴拉伸multiaxial drawing皮心效应skin and core effect皮层效应skin effect防缩non-shrink熟成ripening垂挂sag定型sizing起球现象pilling effect捻度twist旦denier特tex纱yarn股strand粘合adhesion反应粘合reaction bonding压敏粘合pressure sensitive adhesion底漆primer浸渍impregnation浸渍树脂solvent impregnated resin基体matrix聚合物表面活性剂polymeric surfactant高分子絮凝剂polymeric flocculant预发颗粒pre-expanded bead高分子膜polymeric membraneH-膜H-filmLB 膜Langmuir Blodgett film (LB film)半透膜semipermeable membrane反渗透膜Reverse osmosis membrance多孔膜porous membrane各向异性膜anisotropic membrane 正离子交换膜cation exchange membrane 负离子交换膜anionic exchange membrane 吸附树脂polymeric adsorbent潜固化剂latent curing agent硫化剂vulcanizing agent给硫剂sulfur donor agent, sulfur donor 硫化促进剂Ivulcanization accelerator 硫化活化齐U vulcanizationactivator 活化促进剂I activating accelerator 活化剂activator防焦剂scorch retarder抗硫化返原剂anti-reversion agent 塑解剂peptizer偶联剂coupling agent硅烷偶联剂silane coupling agent 钛酸酯偶联剂titanate coupling agent 铝酸酯偶联齐U aluminatecoupling agent增塑增容剂plasticizer extender 分散剂dispersantagent结构控制齐U constitution controller 色料colorant荧光增白剂optical bleaching agent 抗降解剂antidegradant 防老剂anti-aging agent防臭氧剂antiozonant除臭剂re-odorant 抗氧齐U antioxidant热稳定剂heat stabilizer抗静电添加剂antistatic additive 抗静电剂antistatic agent紫外线稳定剂ultraviolet stabilizer 紫外光吸收剂ultraviolet absorber润滑剂lubricant 湿润剂wetting agent 隔离剂separant 增韧剂toughening agent 抗冲改性剂impact modifier 消泡剂antifoaming agent 减阻剂drag reducer 破乳剂demulsifier 粘度改进剂viscosity modifier 增稠剂thickening agent, thickener 阻黏剂abhesive 洗脱剂eluant 附聚剂agglomerating agent 后处理剂I after-treating agent 催干剂drier 防结皮剂anti-skinning agent 纺织品整理剂textile finishing agent aggregation聚集体aggregate 凝聚、聚集coalescence 链缠结chain entanglement 凝聚缠结cohesional entanglement 物理缠结physical entanglement 凝聚态condensed state 凝聚过程condensing process 临界聚集浓度critical aggregation concentration线团-球粒转换coil-globule transition 受限链confined chain 受限态confined state数均分子量number-average molecular weight, number-average molar mass重均分子量weight-average molecular weight, weight-average molar massZ 均分子量Z（Zaverage）-average molecular weight, Z-molar mass黍占均分子量viscosity-average molecular weight , viscosity-average molar mass 聚合度degree of polymerization分子量分布molecular weight distribution , MWD多分散性指数polydispersity index , PID结晶聚合物crystalline polymer聚合物形态学morphology of polymer成核作用nucleation分子成核作用molecular nucleation阿夫拉米方程Avrami equation织构texture液晶态liquid crystal state相分离phase separation微相microphase最低临界共溶（溶解）温度lower critical solution temperature, LCST 最高临界共溶（溶解）温度upper critical solution temperature , UCST 橡胶态rubber state 玻璃态glassy state 高弹态elastomeric state 黍占流态viscous flow state 伸长elongation 高弹形变high elastic deformation 回缩性，弹性复原nerviness 拉伸比draw ratio, extension ratio 泊松比Poisson's ratio 杨氏模量Young's modulus本体模量bulk modulus颈缩现象necking脆-韧转变brittle ductile transition压缩强度compressive strength 氏硬度Rockwell hardness延迟弹性retarded elasticity可逆形变reversible deformation 应力开裂stress cracking应力-应变曲线stress strain curve假塑性pseudoplastic拉胀性auxiticity牛顿流体Newtonian fluid非牛顿流体non-Newtonian fluid宾汉姆流体Bingham fluid冷流cold flow牛顿剪切黏度Newtonian shear viscosity 剪切黏度shear viscosity表观剪切黏度apparent shear viscosity剪切变稀shear thinning触变性thixotropy塑性形变plastic deformation塑性流动plastic flow体积弛豫volume relaxation拉伸黏度extensional viscosity弛豫［作用］relaxation弛豫模量relaxation modulus蠕变柔量creep compliance热畸变温度heat distortion temperature 弛豫谱relaxation spectrum推迟［时间］谱retardation ［time］ spectrum弛豫时间relaxation time推迟时间retardation time动态力学行为dynamic mechanical behavior 动态黏弹性dynamic viscoelasticity 热-机械曲线thermo-mechanical curve 动态转变dynamic transition储能模量storage modulus损耗模量loss modulus复数模量complex modulus复数柔量complex compliance动态黏度dynamic viscosity复数黏度complex viscosity复数介电常数complex dielectric permittivity 介电损耗因子dielectric dissipation factor 介电损耗常数dielectric loss constant 介电弛豫时间dielectric relaxation time 玻璃化转变glass transition 玻璃化转变温度glass-transition temperature次级弛豫secondary relaxation 次级转变secondary transition次级弛豫温度secondary relaxation temperature 开尔文模型Kelvin model麦克斯韦模型Maxwell model时-温叠加原理time-temperature superposition principle玻耳兹曼叠加原理Boltzmann superposition principle平移因子shift factor WLF 公式WLF[Williams-Lendel-Ferry] equation 软化温度softening temperature平衡熔点equilibrium melting point计算机模拟computer simulation分子动力学模拟molecular dynamics simulation蒙特卡洛模拟Monte Carlo simulation。

塑胶模具相关名词中英文对照（精选）第一篇：塑胶模具相关名词中英文对照（精选）射出壓力---injection pressure射出成形---injection molding射出成形機---injection molding machine射出成形模具---injection mold射出裝置---injection unit射出速度---injection speed射出噴嘴,注料嘴---injection nozzle射出容量---machine shot capacity射出率(量)---injection rate煮沸試驗---boiling test手動模具---hand mold,loose mold手動油壓機---hand press縮窩,凹孔---shrinkage pool噴嘴,注嘴---nozzle噴嘴接觸---nozzle touching噴嘴止流---nozzle shut-off支管形噴嘴---nozzle manifold背壓---back pressure止回閥,止逆閥---back pressure valve脫模銷,頂出銷---knock-out pin脫模銷托板,頂出銷托板---knock-out pin plate注射,射料---shot成形壓力,模製壓力---molding pressure成形溫度,模製溫度---molding temperature成形循環,成形週期---molding cycle成形時間,模製時間---molding time成形收縮,模壓收縮---mold shrinkage, molding shrinkage窄澆口,限制形澆口---restricted gate剪切強度,抗剪強度---shear strength增亮劑---brightening agent,optical brightener,optical whitening agent 加速試驗---accelerated test加速老化---accelerated ageing塑性變形---plastic deformation塑性流動---plastic fiow翹曲---warp(ing),warpage拉桿,導柱---tie-bar拉桿間距---tie-bar distance多模穴模具---multi-cavity mold雙色射出成形---double-shot molding超音(聲)波鑲嵌---ultrasonic inserting超音(聲)波焊接---ultrasonic welding頂出,脫模---ejection頂出組合---ejector頂出板---ejector plate,knock-out plate頂出桿,脫模桿---knock-out bar,ejector rod無光面---dull surface低壓射出成形法---low pressure injection molding硬度計---durometer電鍍---electroplating,electrodeposition電鑄模具---electroformed mold尼龍,(聚醯胺樹脂之俗稱)---nylon尼龍纖維---nylon fiber扭曲試驗---torsion test扭力矩---torsion moment發泡劑---blowing agent,expanding agent發泡塑膠,泡沫塑料---plastics foam,expanded plastics, foamed plastics,cellular plastics,plastics sponge拋光布輪---buff,buffing wheel布輪拋光---buffing修邊,除邊---deflashing,definning修邊機,修毛邊機---deflasher剝離,剝皮加工---peeling拉出成形---pultrusion抗刮硬度,刮痕硬度---scratch hardness非破壞性試驗---non-destructive testing疲勞壽命---fatigue life疲勞強度---fatigue strength針眼,針孔---pinhole玻璃纖維強化,熱塑塑膠射出成形---fiberfil molding底漆,底膠,引發劑---primer溢料縫,毛邊槽---flash groove流痕---flow mark冷卻線---frost line原型模,試驗模---prototype mold環境溫度---ambient temperature止流閥---shut-off valve放電---discharge全壓式模具---positive mold輔助壓缸---auxiliary cylinder燙印---hot stamping,roll leaf stamping 彎曲龜裂---flex cracking磨損---abrasion,wear磨耗---abrasion loss莫斯硬度---Mohs’hardness退火---annealing回火---tempering楊氏彈性係數---Young’s modulus of elasticity 油壓增壓器---hydraulic intensifier油壓機---hydraulic press油壓馬達---hydraulic motor焊接---welding老化試驗---ageing test對位圈,定位環---locating ring肉厚---wall thickness脫模斜度---draft angle第二篇：测量学名词中英文对照测绘学名词(中英对照)01.001 测绘学 surveying and mapping, SM01.002 中华人民共和国测绘法 Law of Surveying and Mapping of the People's Republic of China01.003 测绘标准 standards of surveying and mapping01.004 测量规范 specifications of surveys01.005 地形图图式 topographic map symbols01.006 大地测量学 geodesy01.007 地球形状 earth shape, figure of the earth01.008 重力基准网 gravity standard network01.009 重力场gravity field01.010 地心坐标系 geocentric coordinate system01.011 地球椭球 earth ellipsoid01.012 大地原点 geodetic origin01.013 水准原点 leveling origin01.014 测量标志survey mark01.015 测量觇标observation target01.016 高程基准height datum01.017 1954年北京坐标系Beijing geodetic coordinate system195401.018高程系统height system01.019平均海[体]面mean sea level01.020黄海平均海[水]面Huanghai mean sea level01.021海拔height above sea level01.022海军导航卫星系统Navy Navigation Satellite System，NNSS01.023NAVSTAR全球定位系统NAVSTAR Global Positioning System，NAVSTAR GPS01.024 惯性测量系统inertial surveying system，ISS01.025 摄影测量与遥感学photogrammetry and remote sensing01.026 航空摄影测量aerophotogrammetry, aerial photogrammetry01.027 航天摄影测量（又称“太空摄影测量”）space photogrammetry01.028 非地形摄影测量non-topographic photogrammetry01.029 水下摄影测量underwater photogrammetry01.030 航空航天摄影aero—space photogrammetry01.031 航空遥感aerial remote sensing01.032 航天遥感space remote sensing01.033 图像image01.034 影像image, imagery01.035 图形Graphics01.036判读（又称“判释”、“解译”）interpretation01.037 模拟摄影测量analog photogrammetry01.038 解析摄影测量analytical photogrammetry, numerical photogrammetry01.039数字摄影测量digital photogrammetry01.040数字地图模型（又称“数值地型”）digital terrain model, DTM01.041 遥感图象处理image processing of remote sensing01.042 遥感模式识别pattern recognition of remote sensing01.043 地图制图学（又称“地图学”）cartography01.044 地理坐标网geographic graticule01.045 经纬网fictitious graticule01.046 方里网kilometer grid01.047 邻带方里网grid of neighboring zone01.048 坐标格网coordinate grid01.049 地理坐标参考系geographical reference system，GEOREF01.050 地图map01.051 地形图topographic map01.052 平面图plan01.053 普通地图general map01.054 专题地图thematic map01.055 地图集atlas01.056 地球仪globe01.057 地图规范map specifications01.058 地图生产map production01.059 地图投影map projection01.060 地图编制（又称“编图”）map compilation01.061 地图复制map reproduction01.062 地图印刷map printing01.063 地图利用map use01.064 地图量算cartometry01.065 机助地图制图computer-aided cartography，computer-assisted cartography, CAC01.066 自动化制图automatic cartography01.067 自动绘图automatic plotting01.068 图形显示graphic display01.069 遥感制图remote sensing mapping01.070 地名学toponomastics, toponymy01.071 地名geographical name, place name01.072 工程测量学engineering surveying01.073 比例尺scale01.074 基本比例尺basic scale01.075 等高线contour01.076 等高距contour interval01.077 测量平差survey adjustment，adjustment of observations01.078 精度估计precision estimation01.079 精［密］度precision01.080 准确度accuracy01.081 偶然误差accident error01.082 系统误差systematic error01.083 粗差gross error01.084 常差constant error01.085 多余观测redundant observation01.086 闭合差closing error, closure01.087 限差tolerance01.088 相对误差relative error01.089 绝对误差absolute error01.090 中误差mean square error01.091 误差椭圆error ellipse01.092 边长中误差mean square error of side length01.093 测角中误差mean square error of angle observation01.094 方位角中误差mean square error of azimuth01.095 坐标中误差mean square error of coordinate01.096 点位中误差mean square error of a point01.097 高程中误差mean square error of height01.098 国土基础信息系统land base information system01.099 大地控制数据库geodetic data base01.100 重力数据库gravimetric data base01.101 地形数据库topographic data base01.102 地理信息系统geographical information system，GIS01.103 地图数据库map data base01.104 地图数据库管理系统cartographic data basemanagement system01.105 地名数据库place-name data base01.106 地籍信息系统cadastral information system01.107 土地信息系统land information system，LIS01.108 制图专家系统cartographic expert system01.109 海洋测绘hydrographic surveying and charting01.110 测绘仪器instrument of surveying and mapping01.111 大地测量仪器geodetic instrument01.112 测距仪distance measuring instrument，rangefinder01.113 重力仪gravimeter01.114 定位系统positioning system01.115 摄影测量仪器photogrammetric instrument01.116 立体测图仪stereoplotter01.117 数字摄影测量工作站 digital photogrammetric station01.118 全数字化自测图系统full digital automatic mapping system01.119 图形输入设备graphic input unit01.120 图形输出设备graphic output unit01.121 中国测绘学会Chinese Society of Surveying and Mapping，CSSM01.122 国际测绘联合会International Union of Surveying and Mapping，IUSM01.123 国际测量师联合会Federation Internationale des Geometres，FIG（法语）01.124 国际大地测量学与地球物理学International Union of Geodesy and Geophysics，IUGG01.125 国际大地测量学协会International Association of Geodesy IAG01.126 国际摄影测量与遥感学会 International Society forPhotogrammetry and Remote Sensing，ISPRS01.127 国际地图学协会International Cartographic Association，ICA01.128国际海道测量组织International Hydrography Organization, IHO第三篇：物流常用名词中英文对照物流常用名词中英文对照alternate tiers row pattern交错码放AGV无人搬运车anchoring 膨胀螺丝AS/RS(Automatic Storage Retrieval System)自动存取机/系统自动存取仓储系统自动仓库系统assembly packaging集合包装average inventory平均存货battery电瓶beam橫撑，横梁belt conveyor皮带式输送机（带）block pattern row pattern整齐码放bonded warehouse国际物流中心保税仓库brick pattern砌砖式码放buffer stock 缓冲储备cantilever shalving悬臂架cargo freight 货物carrying搬运chain conveyor链条式输送机（带）charger充电机cold chain system冷冻链系统common carrier 公共承运人consolidation装运整合container terminal集装箱中转站contract carrier 契约承运人contract logistics契约物流counterbalance truck平衡式电动(柴油、电动、瓦斯)堆高机cycle inventory周期存货delivery配送depalletizer托盘拆垛机devanning拆箱diagonal bracing斜撑dock leveller月台调整板dock shelter 月台门封(充气式,非充气式)double-deep pallet racking双层深式重型物料钢架drive-in pallet racking直入式重型物料钢架dry cargo干货dunnage填充electronic data interchange电子资料交换EDIexport processing zone加工出口区fill rate供应比率floor utilization percentage地面面积利用率flow(dynamic)racking重型流力架flow(dynamic)rack shelving 轻型(料盒、纸箱)流力架forklift truck 叉车four-way reach truck四向式电动堆高机frame 支柱组frame feet脚底板frame joint柱连杆freight container货物集装箱general cargo一般货物hand pallet truck油压拖板车horizontal bracing橫撑industrial door 工业门industrial vehicle工业车辆intermodal transportation复合一贯运输lashing捆扎加固levelling plate垫片LGV激光引导无人搬运车 load efficient装载效率loading and unloading 装卸logistical utilities物流效用logistics物流materials handling物料搬运mezzanines floor 积层架mini-load AS/RS料盒式自动仓库系統mobile dock leveller月台桥板mobile shelving移动柜net unit load size 净单元货载尺寸operation area 理货区order picking truck电动拣料车order picking指令拣选order shipped complete订货完成率packaged cargo包装货物packaging包装pallet托盘，(木质)栈板pallet container栈板笼架pallet pool system 通用托盘系统pallet racking传统式重型物料钢架palletization托盘化palletizer托盘堆垛机palletizing pattern托盘装载方式pick up货物聚集picking拣货，拣选作业pictorial marking for handling货运标识pinwheel pattern针轮式码放plan view size平面尺寸plastic bin物料盒plastic pallet塑胶栈板platform物流容器，站台，月台physical distribution model物流标准powered pallet truck电动拖板车powered stacker自走式电动堆高机push-back pallet racking后推式重型物料钢架rack 货架rack notice标示牌reach truck前伸式电动堆高机returnable container 通用容器roll container笼车roller conveyor滚筒式输送机（带）safety pin插销safety stock安全储备scrubber洗地机shed临时周转仓库shelving轻量型物料钢架shuttle car梭车slat conveyor条板式输送机（带）slotted-angle shelving角钢架sorting 分类special cargo特殊货物spot stock现场储备stacker crane自动存取机高架吊车stacking堆垛stockout frequency缺货频率storage存储support bar跨梁surface utilization percentage表面利用率sweeper扫地机table trolley物流台车third part logistics第三方物流third party logistics service provider第三方物流服务商transit inventory中转存货transportation运输transportation package size by modular coordination 运输包装系列尺寸tray conveyor盘式输送机（带）truck terminal卡车货运站turntable转盘(变更输送方向)unit load单元货载unit load system单元货载系统upright支柱upright protctors护脚value added network—VAN加值网络vanning装箱vertical conveyor垂直输送机very narrow aisle truck窄巷道电动堆高机warehouse仓库WCS(Warehouse Control System)仓储控制系统WMS(Warehouse Management System)仓储管理系统第四篇：质量管理中英文名词对照质量管理中英文名词对照质量管理中英文名词对照表Accuracy 准确度Active 主动Action 评价.处理Activity 活动Add 加Addition rule 加法运算规则Analysis Covariance 协方差分析Analysis of Variance 方差分析Appraisal Variation 评价变差Approved 承认ASQC 美国质量学会Attribute 计数值Audit 审核Automatic database recovery 数据库错误自动回复 Average 平均数balance 平衡Balance sheet 资产负债对照表Binomial 二项分配Body 机构Brainstorming Techniques 脑力风暴法Business Systems Planning 企业系统规划 Cable 电缆Capability 能力Cause and Effect matrix 因果图.鱼骨图 Center line 中心线check 检查Check Sheets 检查表Chi-square Distribution 卡方分布Clutch spring 离合器弹簧Coining 压印加工Common cause 共同原因Complaint 投诉Compound factor 调合因素Concept 新概念Condenser 聚光镜Conformity 合格Connection 关联Consumer’s risk 消费者之风险Control 控制Control characteristic 管制特性Control chart管制图Control plan 管制计划Correction 纠正Correlation Methods 相关分析法Cost down 降低成本CPI: continuouse Process Improvement 连续工序改善Creep 渐变Cross Tabulation T ables 交叉表CS: customer Sevice 客户中心Cushion 缓冲Customer 顾客DSA: Defects Analysis System 缺陷分析系统Data 数据Data Collection 数据收集Data concentrator 资料集中缓存器DCC: Document Control Center 文控中心Decision 决策.判定Defects per unit 单位缺点数Description 描述Detection 难检度Device 装置Digital 数字Do 执行DOE: Design of Experiments 实验设计Element 元素Else 否则Engineering recbnology 工程技术Entropy 函数Environmental 环境Equipment 设备Estimated accumulative frequency 计算估计累计数EV: Equipment Variation 设备变异Event 事件External Failure 外部失效,外部缺陷FA: Failure Analysis 坏品分析Fact control 事实管理Fatique 疲劳FMEA: Failure Mode and Effect analysis 失效模式与效果分析FPY 合格率FQA: Final Quality Assurance 最终品质保证FQC: Final Quality control 最终品质控制Full-steer 完全转向function 职能Gauge system 量测系统Grade 等级Gum-roll 橡皮滚筒Health meter 体重计Heat press 冲压粘着Histogram 直方图Hi-tech 高科技hypergeometric 超几何分配hysteresis 磁滞现象Improvement 改善Inductance 电感Information 信息Initial review 先期审查Inspection 检验Internal Failure 内部失效,内部缺陷IPQC: In Process Quality Control 制程品质控制IQC: Incomming Quality Control 来料品质控制ISO: International Organization for Standardization 国际标准组织 Law of large number 大数法则Link 连接LCL: Lower Control limit 管制下限LQC: Line Quality Control 生产线品质控制LSL: Lower Size Limit 规格下限Machine 机械Manage 管理Materials 物料Measurement 量测Median 中位数Miss feed 漏送Module,sub-system,sub-unit 单位Momentum 原动力Monte garlo method 原子核分裂热运动法MSA: Measurement System Analysis 量测系统分析Multiplication rule 乘法运算规则NIST 美国:标准技术院Normal 常态分布Occurrence 发生率On.off system 开,关系统Operation Instruction 作业指导书Organization 组织Parameter 参数Parto 柏拉图Parts 零件Parts per million 不良率Passive 消极的,被动的Plan 计划Pulse 脉冲Policy 方针Population 群体Power 力量,能源PQA: Process Quality Assurance 制程品质保证Practice 实务Precision 精密度preemptive 先占式多任务Pressure 压缩Prevention 预防Probability 机率Probability density function 机率密度函数Procedure 流程Process 过程Process capability analysis 制程能力分析图Process control and process capability 制程管制与制程能力Producer’s risk 生产者之风险Product 产品Production 生产Program 方案Projects 项目QA: Quality Assurance 品质保证QC: Quality Control 品质控制QE: Quality Engineering 品质工程QFD: Quality Function Desgin 品质机能展开Quality 质量Quality manual 品质手册Quality policy 品质政策Random experiment 随机试验Random numbers 随机数Range 全距Record 记录Reflow 回流Reject 拒收Repair 返修Repeatusility 再现性Reproducibility 再生性Requirement 要求Residual 误差Response 响应Responsibilities 职责Review 评审Reword 返工Robustness 稳健性Rolled yield 直通率RPN: Risk Priority Number 风险系数sample 抽样,样本Sample space 样本空间Sampling with replacement 放回抽样Sampling without peplacement 不放回抽样Scatter diagram 散布图分析Scrap 报废Screw 螺旋Severity 严重度Shot-peening 微粒冲击平面法Simple random sampling 简单随机取样Size 规格SL: Size Line 规格中心线Slip 滑动Stratified random sampling 分层随机抽样SOP: Standard Operation Procedure 标准作业书SPC: Statistical Process Control 统计制程管制Special cause 特殊原因Specification 规范SQA: Source(Supplier)Quality Assurance 供货商品质保证Stage sampling 分段随机抽样Standard Deviation 标准差Sum of squares 统计表supplier 平方和System 供方systematic sampling 系统,体系Statistical tables 系统抽样Taguchi-method 田口方法Technical committees 技术委员会Test piece 测试片Theory 原理Time stamp 时间戳印Time-lag 延迟Title 标题Torque 转矩Total 求和TQC: Total Quality Control 全面品质控制TQM: Total Quality Management 全面品质管理 Traceablity 追溯Training 培训Transaction processing and logging 交易处理 Trouble 困扰Up and down 上和下UCL: Upper Control Limit 管制上限 USL: Upper Size Limit 规格上限Validation 确认Variable 计量值Variance 变异和Vector 向量Verification 验证Version 版本VOC: voice of Customer 客户需求 VOE: Voice of Engineer 工程需求第五篇：品管中英文名词对照品管中英文名词对照Accuracy 准确度Active 主动Action 评价.处理Activity 活动Add 加Addition rule 加法运算规则Analysis Covariance 协方差分析Analysis of Variance 方差分析Appraisal Variation 评价变差Approved 承认 ASQC 美国质量学会 Attribute 计数值 Audit 审核Automatic database recovery 数据库错误自动回复Average 平均数 balance 平衡Balance sheet 资产负债对照表 Binomial 二项分配 Body 机构Brainstorming Techniques 脑力风暴法Business Systems Planning 企业系统规划 Cable 电缆 Capability 能力Cause and Effect matrix 因果图.鱼骨图Center line 中心线check 检查Check Sheets 检查表Chi-square Distribution 卡方分布Clutch spring 离合器弹簧Coining 压印加工 Common cause 共同原因 Complaint 投诉Compound factor 调合因素 Concept 新概念 Condenser 聚光镜 Conformity 合格 Connection 关联Consumer’s risk 消费者之风险 Control 控制Control characteristic 管制特性 Control chart 管制图 Control plan 管制计划 Correction 纠正Correlation Methods 相关分析法 Cost down 降低成本CPI: continuouse Process Improvement 连续工序改善Creep 渐变Cross Tabulation T ables 交叉表 CS: customer Sevice 客户中心Cushion 缓冲 Customer 顾客DSA: Defects Analysis System 缺陷分析系统 Data 数据Data Collection 数据收集Data concentrator 资料集中缓存器DCC: Document Control Center 文控中心 Decision 决策.判定Defects per unit 单位缺点数 Description 描述 Detection 难检度 Device 装置 Digital 数字 Do 执行DOE: Design of Experiments 实验设计 Element 元素 Else 否则Engineering recbnology 工程技术Entropy 函数Environmental 环境 Equipment 设备Estimated accumulative frequency 计算估计累计数EV: Equipment Variation 设备变异 Event 事件External Failure 外部失效,外部缺陷 FA: Failure Analysis 坏品分析 Fact control 事实管理 Fatique 疲劳FMEA: Failure Mode and Effect analysis 失效模式与效果分析FPY 合格率FQA: Final Quality Assurance 最终品质保证 FQC: Final Quality control 最终品质控制 Full-steer 完全转向 function 职能Gauge system 量测系统 Grade 等级 Gum-roll 橡皮滚筒 Health meter 体重计 Heat press 冲压粘着 Histogram 直方图 Hi-tech 高科技hypergeometric 超几何分配hysteresis 磁滞现象Improvement 改善Inductance 电感Information 信息 Initial review 先期审查 Inspection 检验Internal Failure 内部失效,内部缺陷IPQC: In Process Quality Control 制程品质控制IQC: Incomming Quality Control 来料品质控制ISO: International Organization for Standardization 国际标准组织Law of large number 大数法则 Link 连接LCL: Lower Control limit 管制下限 LQC: Line Quality Control 生产线品质控制LSL: Lower Size Limit 规格下限Machine 机械Manage 管理Materials 物料Measurement 量测Median 中位数Miss feed 漏送Module,sub-system,sub-unit 单位 Momentum 原动力Monte garlo method 原子核分裂热运动法MSA: Measurement System Analysis 量测系统分析Multiplication rule 乘法运算规则 NIST 美国:标准技术院 Normal 常态分布 Occurrence 发生率 On.off system 开,关系统Operation Instruction 作业指导书Organization 组织Parameter 参数 Parto 柏拉图 Parts 零件Parts per million 不良率 Passive 消极的,被动的 Plan 计划 Pulse 脉冲 Policy 方针 Population 群体 Power 力量,能源PQA: Process Quality Assurance 制程品质保证Practice 实务Precision 精密度preemptive 先占式多任务Pressure 压缩Prevention 预防Probability 机率Probability density function 机率密度函数Procedure 流程Process 过程Process capability analysis 制程能力分析图Process control and process capability 制程管制与制程能力Producer’s risk 生产者之风险Product 产品Production 生产Program 方案 Projects 项目QA: Quality Assurance 品质保证 QC: Quality Control 品质控制QE: Quality Engineering 品质工程QFD: Quality Function Desgin 品质机能展开 Quality 质量Quality manual 品质手册Quality policy 品质政策Randomexperiment 随机试验 Random numbers 随机数 Range 全距 Record 记录 Reflow 回流 Reject 拒收 Repair 返修Repeatusility 再现性 Reproducibility 再生性 Requirement 要求Residual 误差Response 响应Responsibilities 职责Review 评审Reword 返工 Robustness 稳健性 Rolled yield 直通率RPN: Risk Priority Number 风险系数 sample 抽样,样本 Sample space 样本空间Sampling with replacement 放回抽样Sampling without peplacement 不放回抽样Scatter diagram 散布图分析Scrap 报废Screw 螺旋Severity 严重度Shot-peening 微粒冲击平面法Simple random sampling 简单随机取样 Size 规格SL: Size Line 规格中心线 Slip 滑动Stratified random sampling 分层随机抽样SOP: Standard Operation Procedure 标准作业书 SPC: Statistical Process Control 统计制程管制 Special cause 特殊原因 Specification 规范SQA: Source(Supplier)Quality Assurance 供货商品质保证Stage sampling 分段随机抽样 Standard Deviation 标准差 Sum of squares 统计表 supplier 平方和 System 供方systematic sampling 系统,体系Statistical tables 系统抽样Taguchi-method 田口方法 Technical committees 技术委员会 Test piece 测试片 Theory 原理Time stamp 时间戳印Time-lag 延迟Title 标题Torque 转矩Total 求和TQC: T otal Quality Control 全面品质控制 TQM: Total Quality Management 全面品质管理 Traceablity 追溯 Training 培训Transaction processing and logging 交易处理 Trouble 困扰 Up and down 上和下UCL: Upper Control Limit 管制上限 USL: Upper Size Limit 规格上限 Validation 确认 Variable 计量值 Variance 变异和 Vector 向量Verification 验证 Version 版本VOC: voice of Customer 客户需求 VOE: Voice of Engineer 工程需求质量相关术语英中文对照IQC: incomming quality control 进料检验LQC: line quality control 生产线品质控制IPQC: inprocess quality control 制程品质控制FQC: final quality control 最终品质控制OQC: outgoing quality control 出货品质控制PQA: process quality control 制程品质保证FQA: final quality assurance 最终品质保证SQA: source(supplier)quality assurance 供应商品质保证DAS: defect analysis system 缺陷分析系统DCC: document control center 文控中心QCC: quality control circle 品管圈QA: quality assurance OR quality audit 品质保证品质稽核QC: quality control 品质控制QE: quality engineering 品质工程TRAINING: 培训ZD: zero defect 零缺陷FMEA: failure mode and effects analysis 潜在缺陷模式和影响分析FMA: failure mode analysis 故障模式分析FEA: failure effect analysis 故障效应分析FCA: failure criticality analysis 故障危害度分析FA: failure analysis 坏品分析 CS: customer service 客户服务CPI: continuous process improvement 连续工序改善DOE: design of experiment 实验设计SQC: statistical quality control 统计品质控制TQC: total quality control 全面品质控制CWQC: company-wide quality control 全公司品质管理GWQC: group-wide quality control 全集团品质管理PDCA: plan do check action 计划执行检查矫正AQL: acceptable quality level 允收水准(接收质量限)SOP: standard operation procedure 操作标准SIP: standard inspection procedure 检验标准IE: industrial research 工业工程MR: method research 方法研究OR: operation research 工作研究VE: value engineering 价值工程5W2H: what 做什么？有必要吗？ Why 为什么要做？目的在哪里？where 哪里做？没有更合适的地方吗？When 何时做？时间是否合适？Who 谁做？有没有更合适的人？How 如何做？有没有更好的方法？how much 需要的成本如何？4M1E: manpower 人员method 方法machine 机器material物料environment 环境。

铸造实用词汇(英文)————————————————————————————————作者：————————————————————————————————日期：21. charging mixture (配料)2. gas vent (通气孔)air vent (通气孔)3. alcohol base wash (酒精基涂模剂)4. alloy (合金)alloy cast iron (合金铸铁)5. anchor pin (定位销)6. annealing (退火)annealing furnace (退火炉)7. arc welding (电弧熔接)8. as cast (铸胚/毛胚铸件)9. atmospheric core / pencil core(砂心/ 增压/透气砂心)10. bath analysis (炉前分析)11. hand molding (手工造模)12. bending strength (抗弯强度)13. bending test (弯曲试验)14. binder (黏结剂)15. furan resin夫喃树脂16. blow hole / gas hole (气孔) 17. Brinell hardness (布氏硬度)18. brittleness (脆性)19. broken casting at gate / riser or vent(铸件破损)去除浇口, 冒口, 溢流口时, 一起将铸件主体部分也去除的破坏缺陷20. case hardening (表面硬化)21. pouring / pour / cast (浇铸/浇注)22. castability (铸造性)23. casting design / casting plan (铸造方案)24. cast iron / iron castings (铸铁)25. cavity (缩孔)26. ceramic core (陶瓷砂心)27. ceramic filter (陶瓷过滤片)28. ceramic tube (陶管)29. chaplet (砂心撑)30. chill (冷硬/冷激)31. chiller / densener (冷铁)32. chunky graphite (块状/短小石墨)33. clay (黏土)34. riser(冒口)35. coat/mold wash/facing material (涂料/涂模剂)36. washing / coating (涂模/上涂料)37. cold junction (冷接点)38. composites / composite material (复合材料)sand mill / sand mixer (混砂机)sand mixing (练砂)sand mold (砂模)39. contraction / shrinkage (收缩/缩孔/疏松)40. conveyor (输送机)41. core assemble (组合砂心)44. core box (砂心盒)45. core grid / rodding (砂心骨)46. core making machine (砂心机)47. lifting / raised mold / core raise (砂心上浮)48. core washing (砂心涂料)49. corrosion (腐蚀)50. crack (裂痕)=龟裂51. crystal (晶体)52. curing (硬化)53. cut (冲砂)=冲蚀354. metallic pattern (金属模)55. galvanizing (镀锌)56. dirt / scum / dross / slag (熔渣/ 浮渣/ 炉渣)57. sprue / down sprue / down gate (下浇道/ 竖浇道)58. draft (拔模斜度)59. drag (下模/下砂箱/下模箱)60. dressing / cleaning (上涂料/涂料/清理)61. electric furnace (电炉)62. electron microscope (电子显微镜)63. elongation (伸长/伸长率)64. etching solution/etching agent/etchingreagent (浸蚀液)65. open shrinkage / external shrinkage (外缩孔)66. ferritic spheroidal graphite cast iron(肥粒体球状石墨铸铁)67. ferrite (肥粒铁)68. machining allowance / finishing allowance (加工余量)69. flake graphite cast iron (片状石墨铸铁) 70. flow chart (流程图)71. CE meter (热分析)72. full size /full dimension (全尺寸)73. graphitic carbon / graphite carbon (石墨碳)74. gray cast iron (灰口铸铁/普通铸铁/片状石墨铸铁)75. green sand mold (湿砂模)76. hardener / hardening agent (硬化剂)77. hardness test (硬度试验)78. high frequency electric induction furnace (高周波感应电炉)79. holding furnace (保温炉)80. impact test (冲击试验)81. Charpy impact test（夏比冲击试验）82. impact value (冲击值)83. indirect chiller (间接冷铁)84. inlet / pouring basin / pouring cup (浇杯)85. Inoculant (接种剂)86. Inoculation (接种)87. ladle（浇包/浇桶/铁水包）88. molding flask (砂箱)89. joint surface (合模面)90. keel block (Y型试块)91. knock-out / shake-out (清箱/开箱)92. low frequency induction furnace (低周波感应电炉)93. liquid penetrant testing (渗透探伤试验/PTtest)94. low temperature annealing (低温退火)95. magnetic powder test (MT/磁粉探伤)96. melting furnace (熔解炉)97. metal flask (金属砂箱)98. metallographic microscope (金相显微镜)99. metallography (金相学)100. parting line (分模线).101. parting plane（分割面）102. pattern (模型/模具)103. pattern coating (模型涂漆)104. pearlite (波来铁)105. burn on / sand burning (烧结/结砂)4106. pig iron (生铁)107. scrap steel (废钢)108. pin hole (针孔)109. pore (气孔)110. porosity (多孔性/气孔率)111. pouring rate (浇铸速度)112. pouring temperature (浇注温度)113. pouring time (浇注时间)114. pouring weight (浇注重量)115. quality control (质量管理)116. X-ray inspection / radiography (X线探伤) 117. rapping (起模)118. ratio of graphite spheroidization (球化率) 119. rejected castings (不良品)120. residual stress (残留应力/铸造应力) 121. roll over machine (翻转机)122. sag core (砂心下垂)123. sand blast (喷砂)124. sand inclusion (夹砂)125. short pours / short run (浇注不足) 126. shot blast (抛丸)127. shrinkage cavity (缩孔)128. shrinkage crack (缩裂)129. s lag off agent / slag disposal agent (除渣剂)130. s lag inclusion (夹渣)131. s olidification time (凝固时间)132. s pherodial graphite (球状石墨)133. s pheroidizing agent (球化剂)134. strength test (强度试验)135. stress concentration (应力集中)136. stress relief (应力消除)137. rough surface (表面粗糙)138. surface fold / gas run (皱皮/流缝/冷隔)139. surface roughness (表面粗糙度)140. surface treatment (表面处理)141. tensile strength (抗拉强度)142. tensile test (拉伸试验)143. test piece/test lug (试片)144. used sand (旧砂)145. working reference point (加工基准)146. Ultrasonic testing (UT/超声波检测)147. Gating system （浇注系统）148. test coupon （试棒）149. Non-destructive testing (NDT/非破坏性测试)150. Visual inspection (VT/目测)151. rough machining (粗加工)152. finishing machining（精加工）153. Non conformity report (NCR 不符合报告)154. Corrective action report (改善措施报告)155. solidification simulation (凝固模拟)5。

材料性能中英文对照物理性能Physical properties机械性能Mechanical properties 热性能Thermal properties难燃性Flame retardance玻纤含量Glass Fiber Content比重Specific gravity抗张性Tensile properties弯曲性Flexural properties IZOD 缺口冲击强度IZOD impact value热变形温度Deflection temperatureunder load拉伸强度Tensile strength断裂伸长率Elongation at break熔融指数Melt flow rate弯曲强度Flexural strength弯曲弹性率/摸量Flexural modulus测试项目Properties item测试条件Test condition测试方法Test method测试数值Test method单位Unites吸水率Water Absorption全光线透射率Light Transmittance雾度Haze折射率Refractive Index抗拉强度Resistance strength伸长率Tensility拉伸弹性率Tensile flexibility弯曲弹性模量Curve flexibility module 悬臂梁式冲击强度Izod impact strength ofunnotched specimens洛氏硬度Rockwell hardness表面电阻系数Surface Resistivity体积电阻系数Volume Resistivity绝缘击穿强度Dielectric Strength介电常数Dielectric Constant介质衰耗因数Dissipation Factor维卡软化温度Vicat Softening Poin比热Specific heat线膨胀系数Coefficient of LinearThermal Expansion。

（完整版）流体力学常用名词中英文对照流体力学常用名词流体动力学fluid dynamics 连续介质力学mechanics of continuous 介质medium 流体质点fluid particle 无粘性流体nonviscous fluid, inviscid 连续介质假设continuous medium hypothesis 流体运动学fluid kinematics 水静力学hydrostatics 液体静力学hydrostatics 支配方程governing equation 伯努利方程Bernoulli equation 伯努利定理Bernonlli theorem 毕奥- 萨伐尔定律Biot-Savart law 欧拉方程Euler equation 亥姆霍兹定理Helmholtz theorem 开尔文定理Kelvin theorem 涡片vortex sheet 库塔- 茹可夫斯基条件Kutta-Zhoukowski condition 布拉休斯解Blasius solution 达朗贝尔佯廖d'Alembert paradox 雷诺数Reynolds number 施特鲁哈尔数Strouhal number 随体导数material derivative 不可压缩流体incompressible fluid 质量守恒conservation of mass 动量守恒conservation of momentum 能量守恒conservation of energy 动量方程momentum equation 能量方程energy equation 控制体积control volume 液体静压hydrostatic pressure 涡量拟能enstrophy 压差differential pressure 流［动］flow 流线stream line 流面stream surface 流管stream tube 迹线path, path line 流场flow field 流态flow regime 流动参量flow parameter 流量flow rate, flow discharge 涡旋vortex 涡量vorticity 涡丝vortex filament 涡线vortex line 涡面vortex surface 涡层vortex layer 涡环vortex ring 涡对vortex pair 涡管vortex tube 涡街vortex street 卡门涡街Karman vortex street 马蹄涡horseshoe vortex 对流涡胞convective cell 卷筒涡胞roll cell 涡eddy 涡粘性eddy viscosity 环流circulation 环量circulation 速度环量velocity circulation 偶极子doublet, dipole 驻点stagnation point 总压[ 力] total pressure 总压头total head 静压头static head 总焓total enthalpy 能量输运energy transport 速度剖面velocity profile 库埃特流Couette flow 单相流single phase flow 单组份流single-component flow 均匀流uniform flow 非均匀流nonuniform flow 二维流two-dimensional flow 三维流three-dimensional flow 准定常流quasi-steady flow 非定常流unsteady flow, non-steady flow 暂态流transient flow 周期流periodic flow 振荡流oscillatory flow 分层流stratified flow 无旋流irrotational flow 有旋流rotational flow 轴对称流axisymmetric flow 不可压缩性incompressibility 不可压缩流[动] incompressible flow 浮体floating body 定倾中心metacenter 阻力drag, resistance 减阻drag reduction 表面力surface force 表面张力surface tension 毛细[ 管]作用capillarity 来流incoming flow 自由流free stream 自由流线free stream line 外流external flow 进口entrance, inlet 出口exit, outlet 扰动disturbance, perturbation 分布distribution 传播propagation 色散dispersion 弥散dispersion 附加质量added mass ,associated mass 收缩contraction 镜象法image method 无量纲参数dimensionless parameter 几何相似geometric similarity 运动相似kinematic similarity 动力相似[ 性] dynamic similarity 平面流plane flow 势potential 势流potential flow 速度势velocity potential 复势complex potential 复速度complex velocity 流函数stream function 源source 汇sink 速度[ 水] 头velocity head 拐角流corner flow 空泡流cavity flow 超空泡supercavity 超空泡流supercavity flow 空气动力学aerodynamics 低速空气动力学low-speed aerodynamics 高速空气动力学high-speed aerodynamics 气动热力学aerothermodynamics 亚声速流[ 动] subsonic flow 跨声速流[ 动] transonic flow 超声速流[ 动] supersonic flow 锥形流conical flow 楔流wedge flow 叶栅流cascade flow 非平衡流[ 动] non-equilibrium flow 细长体slender body 细长度slenderness 钝头体bluff body 钝体blunt body 翼型airfoil 翼弦chord 薄翼理论thin-airfoil theory 构型configuration 后缘trailing edge 迎角angle of attack 失速stall 脱体激波detached shock wave 波阻wave drag 诱导阻力induced drag 诱导速度induced velocity 临界雷诺数critical Reynolds number 前缘涡leading edge vortex 附着涡bound vortex 约束涡confined vortex 气动中心aerodynamic center 气动力aerodynamic force 气动噪声aerodynamic noise 气动加热aerodynamic heating 离解dissociation 地面效应ground effect 气体动力学gas dynamics 稀疏波rarefaction wave 热状态方程thermal equation of state 喷管Nozzle 普朗特- 迈耶流Prandtl-Meyer flow 瑞利流Rayleigh flow 可压缩流[ 动] compressible flow 可压缩流体compressible fluid 绝热流adiabatic flow 非绝热流diabatic flow 未扰动流undisturbed flow 等熵流isentropic flow 匀熵流homoentropic flow 兰金- 于戈尼奥条件Rankine-Hugoniot condition 状态方程equation of state 量热状态方程caloric equation of state 完全气体perfect gas 拉瓦尔喷管Laval nozzle 马赫角Mach angle 马赫锥Mach cone 马赫线Mach line 马赫数Mach number 马赫波Mach wave 当地马赫数local Mach number 冲击波shock wave 激波shock wave 正激波normal shock wave 斜激波oblique shock wave 头波bow wave 附体激波attached shock wave 激波阵面shock front 激波层shock layer 压缩波compression wave 反射reflection 折射refraction 散射scattering 衍射diffraction 绕射diffraction 出口压力exit pressure 超压[ 强] over pressure 反压back pressure 爆炸explosion 爆轰detonation 缓燃deflagration 水动力学hydrodynamics 液体动力学hydrodynamics 泰勒不稳定性Taylor instability盖斯特纳波Gerstner wave 斯托克斯波Stokes wave 瑞利数Rayleigh number 自由面free surface 波速wave speed, wave velocity 波高wave height 波列wave train 波群wave group 波能wave energy 表面波surface wave表面张力波capillary wave 规则波regular wave 不规则波irregular wave 浅水波shallow water wave 深水波deep water wave 重力波gravity wave 椭圆余弦波cnoidal wave 潮波tidal wave 涌波surge wave 破碎波breaking wave 船波ship wave 非线性波nonlinear wave 孤立子soliton 水动［力］噪声hydrodynamic noise 水击water hammer 空化cavitation 空化数cavitation number 空蚀cavitation damage 超空化流supercavitating flow 水翼hydrofoil 水力学hydraulics 洪水波flood wave 涟漪ripple 消能energy dissipation 海洋水动力学marine hydrodynamics 谢齐公式Chezy formula 欧拉数Euler number 弗劳德数Froude number 水力半径hydraulic radius 水力坡度hvdraulic slope 高度水头elevating head 水头损失head loss 水位water level 水跃hydraulic jump 含水层aquifer 排水drainage 排放量discharge 壅水曲线back water curve 压［强水］头pressure head 过水断面flow cross-section 明槽流open channel flow 孔流orifice flow 无压流free surface flow 有压流pressure flow 缓流subcritical flow急流supercritical flow 渐变流gradually varied flow 急变流rapidly varied flow 临界流critical flow 异重流density current, gravity flow 堰流weir flow 掺气流aerated flow 含沙流sediment-laden stream 降水曲线dropdown curve 沉积物sediment, deposit 沉［降堆］积sedimentation, deposition 沉降速度settling velocity 流动稳定性flow stability 不稳定性instability 奥尔- 索末菲方程Orr-Sommerfeld equation 涡量方程vorticity equation 泊肃叶流Poiseuille flow 奥辛流Oseen flow 剪切流shear flow 粘性流［动］viscous flow 层流laminar flow 分离流separated flow 二次流secondary flow 近场流near field flow 远场流far field flow 滞止流stagnation flow 尾流wake ［flow］回流back flow 反流reverse flow 射流jet 自由射流free jet 管流pipe flow, tube flow 内流internal flow 拟序结构coherent structure 猝发过程bursting process 表观粘度apparent viscosity 运动粘性kinematic viscosity 动力粘性dynamic viscosity 泊poise 厘泊centipoise 厘沱centistoke 剪切层shear layer 次层sublayer流动分离flow separation 层流分离laminar separation 湍流分离turbulent separation 分离点separation point 附着点attachment point 再附reattachment 再层流化relaminarization 起动涡starting vortex 驻涡standing vortex 涡旋破碎vortex breakdown 涡旋脱落vortex shedding 压［力］降pressure drop 压差阻力pressure drag 压力能pressureenergy 型阻profile drag 滑移速度slip velocity 无滑移条件non-slip condition 壁剪应力skin friction, frictional drag 壁剪切速度friction velocity 磨擦损失friction loss 磨擦因子friction factor 耗散dissipation 滞后lag 相似性解similar solution 局域相似local similarity 气体润滑gas lubrication 液体动力润滑hydrodynamic lubrication 浆体slurry 泰勒数Taylor number 纳维- 斯托克斯方程Navier-Stokes equation 牛顿流体Newtonian fluid 边界层理论boundary later theory 边界层方程boundary layer equation 边界层boundary layer 附面层boundary layer 层流边界层laminar boundary layer 湍流边界层turbulent boundary layer 温度边界层thermal boundary layer 边界层转捩boundary layer transition 边界层分离boundary layer separation 边界层厚度boundary layer thickness 位移厚度displacement thickness 动量厚度momentum thickness 能量厚度energy thickness 焓厚度enthalpy thickness 注入injection 吸出suction 泰勒涡Taylor vortex 速度亏损律velocity defect law 形状因子shape factor 测速法anemometry 粘度测定法visco[si] metry 流动显示flow visualization 油烟显示oil smoke visualization 孔板流量计orifice meter 频率响应frequency response 油膜显示oil film visualization 阴影法shadow method 纹影法schlieren method 烟丝法smoke wire method 丝线法tuft method 说明氢泡法nydrogen bubble method 相似理论similarity theory 相似律similarity law 部分相似partial similarity 定理pitheorem, Buckingham theorem 静[态]校准static calibration 动态校准dynamic calibration 风洞wind tunnel 激波管shock tube 激波管风洞shock tube wind tunnel 水洞water tunnel 拖曳水池towing tank 旋臂水池rotating arm basin 扩散段diffuser 测压孔pressure tap 皮托管pitot tube 普雷斯顿管preston tube 斯坦顿管Stanton tube 文丘里管Venturi tube U 形管U-tube 压强计manometer 微压计micromanometer 多管压强计multiple manometer 静压管static [pressure]tube 流速计anemometer 风速管Pitot- static tube 激光多普勒测速计laser Doppler anemometer ,laser Doppler velocimeter 热线流速计hot-wire anemometer 热膜流速计hot- film anemometer 流量计flow meter 粘度计visco[si] meter 涡量计vorticity meter 传感器transducer , sensor 压强传感器pressure transducer 热敏电阻thermistor 示踪物tracer 时间线time line 脉线streak line 尺度效应scale effect 壁效应wall effect 堵塞blockage 堵寒效应blockage effect 动态响应dynamic response 响应频率response frequency 底压base pressure 菲克定律Fick law 巴塞特力Basset force 埃克特数Eckert number 格拉斯霍夫数Grashof number 努塞特数Nusselt number 普朗特数prandtl number 雷诺比拟Reynolds analogy 施密特数schmidt number 斯坦顿数Stanton number 对流convection 自由对流naturalconvection, free convec-tion 强迫对流forced convection 热对流heat convection 质量传递mass transfer 传质系数mass transfer coefficient 热量传递heat transfer 传热系数heat transfer coefficient 对流传热convective heat transfer 辐射传热radiative heat transfer 动量交换momentum transfer 能量传递energy transfer 传导conduction 热传导conductive heat transfer 热交换heat exchange 临界热通量critical heat flux 浓度concentration扩散diffusion 扩散性diffusivity 扩散率diffusivity 扩散速度diffusionvelocity 分子扩散molecular diffusion 沸腾boiling 蒸发evaporation 气化gasification 凝结condensation 成核nucleation 计算流体力学computational fluid mechanics 多重尺度问题multiple scale problem 伯格斯方程Burgers equation 对流扩散方程convection diffusion equationKDU 方程KDV equation 修正微分方程modified differential equation 拉克斯等价定理Lax equivalence theorem 数值模拟numerical simulation 大涡模拟large eddy simulation 数值粘性numerical viscosity 非线性不稳定性nonlinear instability 希尔特稳定性分析Hirt stability analysis 相容条件consistency condition CFL 条件Courant- Friedrichs- Lewy condition ,CFL condition 狄里克雷边界条件Dirichlet boundary condition 熵条件entropy condition 远场边界条件far field boundary condition 流入边界条件inflow boundary condition 无反射边界条件nonreflecting boundary condition 数值边界条件numerical boundary condition 流出边界条件outflow boundary condition 冯. 诺伊曼条件von Neumann condition 近似因子分解法approximate factorization method 人工压缩artificial compression 人工粘性artificial viscosity 边界元法boundary element method 配置方法collocation method 能量法energy method 有限体积法finite volume method 流体网格法fluid in cell method,FLIC method 通量校正传输法flux-corrected transport method 通量矢量分解法flux vector splitting method 伽辽金法Galerkin method 积分方法integral method标记网格法marker and cell method, MAC method 特征线法method ofcharacteristics 直线法method of lines 矩量法moment method 多重网格法multi- grid method 板块法panel method 质点网格法particle incell method, PIC method 质点法particle method 预估校正法predictor-corrector method 投影法projection method 准谱法pseudo-spectral method 随机选取法random choice method 激波捕捉法shock-capturing method 激波拟合法shock-fitting method 谱方法spectral method 稀疏矩阵分解法split coefficient matrix method 不定常法time-dependent method 时间分步法time splitting method 变分法variational method 涡方法vortex method 隐格式implicit scheme 显格式explicit scheme 交替方向隐格式alternating direction implicit scheme, ADI scheme 反扩散差分格式anti-diffusion difference scheme 紧差分格式compact difference scheme 守恒差分格式conservation difference scheme 克兰克- 尼科尔森格式Crank-Nicolson scheme 杜福特- 弗兰克尔格式Dufort-Frankel scheme 指数格式exponential scheme 戈本诺夫格式Godunov scheme 高分辨率格式high resolution scheme 拉克斯- 温德罗夫格式Lax-Wendroff scheme 蛙跳格式leap-frogscheme 单调差分格式monotone difference scheme 保单调差分格式monotonicity preserving diffe-rence scheme 穆曼- 科尔格式Murman-Cole scheme 半隐格式semi-implicit scheme 斜迎风格式skew-upstream scheme 全变差下降格式total variation decreasing scheme TVD scheme 迎风格式upstream scheme , upwind scheme 计算区域computational domain 物理区域physical domain 影响域domain of influence 依赖域domain of dependence区域分解domain decomposition 维数分解dimensional split 物理解physical solution 弱解weak solution 黎曼解算子Riemann solver 守恒型conservation form 弱守恒型weak conservation form强守恒型strong conservation form 散度型divergence form 贴体曲线坐标body-fitted curvilinear coordi-nates [ 自] 适应网格[self-] adaptive mesh 适应网格生成adaptive grid generation 自动网格生成automatic gridgeneration 数值网格生成numerical grid generation 交错网格staggered mesh 网格雷诺数cell Reynolds number 数植扩散numericaldiffusion 数值耗散numerical dissipation 数值色散numerical dispersion 数值通量numerical flux 放大因子amplification factor 放大矩阵amplification matrix 阻尼误差damping error 离散涡discrete vortex 熵通量entropy flux 熵函数entropy function 分步法fractional step method。

一、基本术语1。

铸造：casting , founding ，foundry2.砂型铸造: Sand casting process3.特种铸造：Special casting process4。

铸件: casting5。

毛坯铸件：Rough casting6.砂型铸件：Sand casting7.试制铸件：Pilot casting8.铸态铸件：as-cast casting9。

铸型［型]：mold10。

铸造工艺：Casting process, foundry technology11.铸造用材料: Foundry materials12.铸造工艺材料：Consumable materials13。

铸造设备：Foundry equipment，foundry facilities14.铸工：Caster，founder, foundry worker15.铸造工作者: foundryman16。

铸造车间: Foundry shop17.铸造厂：Foundry18。

铸造分厂：Attached foundry, captive foundry, tied foundry 19.铸造三废: Foundry affluent20。

一批： A batch21。

一炉： A cast，a heat，a melt22.铸焊: Cast welding，flow welding23。

铸锭：ingot二、铸造合金及熔炼、浇注2。

1铸造合金基础术语1。

铸造合金: Cast alloy2。

共晶合金系: Eutectic alloy system3。

共晶合金: Eutectic alloy4.亚共晶合金：Hypoeutectic alloy5。

过共晶合金：Hypereutectic alloy6。

共晶团：Eutectic cell7.共晶温度: Eutectic temperature8.共晶转变：Eutectic reaction, eutectic transformation 9。