下载文档原格式
测井3233 1logging job order sheet测井通知单34 2real time data实时资料35 3depth match校深36 4reservoir储层37 5contract合同38 6raw record data原始资料39 7quality rule质量标准40 8sensor传感器41 9gainning mud漏泥浆42 10 2 decimal places两位数43 11inclination井斜44 12azimmuth方位45 13slide造斜46 14abnormal curve非正式曲线47 15absolute permeabiliy绝对渗透率48 16abysmal deposit深海沉积49 17acceptance quality level验收质量标准50 18acoustic imaging声成像51 19porosity孔隙度52 20acoustic scanner tool声波扫描仪53 21acoustic signature log声波波列测井54 22active活动的，有效的55 23actual实际的，有效的，现行的56 24error误差5725resolution分辨率58 26DD（directional drilling定向钻井59 27exploration勘探60 28adjoining rock围岩61 29adjacent formation围岩62 30adjoining well邻井63 31adjustment well调整井6465bad finishing job复杂的打捞工作99 66bad parity奇偶错误100 67bailed (sand) sample捞出的砂样101 68balance平衡102 69bale (baling)打包103 70balling formation易泥包的地层,易在井壁形104成泥饼的地层105 71band sediment(oil pool)条带状沉积物(油藏)106 72barite重晶石107 73bar diagram直方图108 74bare裸的;无反应;仅仅109 75barrier layer(zone)阻挡层110 76base-line shift基线偏移111 77base price底价112 78bass粘土岩113 79bating井眼加深114 80beach海滩,海滨,湖滩115 81bed correction层厚校正116 82bed of interest目的层11783bed resolution分层能力118 84bed response地层响应119 85before calibration summary测前刻度记录120 86before log verification测前校验121 87belly band(buster)安全带122 88below zero低于零123 89bench section横剖面124 90best-fit line最佳拟合线125 91BHCS(borehole compensated sonic)井眼补偿声波测井126 92B-H curve(magnetization curve)磁化曲线127 93BHC-VD(sonic,variable density log)井眼补偿声波变密度测井128 94bond index胶结指数129 95borehole status井眼状况130 96BHT(bottom hole temperature)井底温度131 97BHTV(borehole televiewer)井下电视132 98big casing gun大套管射孔器133134connate water(saturation)原生水(饱和度)169 135connected graph连通图170 136connate fluid原生流体,残余流体171 137consistency一致性;稠度172 138consistancy check一致性检查173 139constant porosity line等孔隙度线174 140contact well logging贴井壁测井174 141container rock储层175 142continuity sand production连续出砂176 143continuity check通断检查177144continuous flow profile连续流量剖面178 145contour of oil sand油层等高线图,油层构造图179 146contrast对比;反差180 147conventional惯用的,常规的,约定的181 148conventional water injection正注182 149cooperation合作,协作183 150core bit取芯钻头184 151core container岩心筒185 152core intersection岩心断面186 153core recovery岩心收获率187 154core run取芯进尺188 155core sample岩样189 156coring gun井壁取芯器190 157coring operation(tool)取芯作业(工具)191 158corrected depth校正后的深度192 159correlation logging对比测井193 160country rock原岩,母岩,围岩194 161cross-section display剖面显示195 162crude data原始资料196 163curve plotter曲线绘图仪197 164curve scale曲线比例尺198 165curve separation曲线的幅度差199 166cyberlook快速直观解释,计算机解释结果200 167dielectric constant介电常数201 168domnhole calibration井下刻度202203DIFL Dual Induction-Focused Log 双感应-聚焦测井239204DIP High Resolution 4-Arm Diplog 高分辨率4臂倾角测井240205DLL Dual Laterolog 双侧向测井241206DPIL Dual Phase Induction Log 双相位感应测井207FMT Formation Multi-Tester 重复地层测试208GR Gamma Ray 自然伽玛209HDIL High Difinition Induction Log 高分辨率感应210HDLL High resolusion Dual Latero Log 高分辨率侧向211MAC Multipole Array Acoustilog 多极子阵列声波212MLL Micro Laterolog 微侧向测井213MRIL Megnetic Resonance Image Log 核磁共振214NEU Neutron Log 中子测井215RCI Reservoir Characterization Instrument 储层描述仪216ROCR Rotary Sidewall Coring Tool旋转井壁取心217SBT Segmented Bond Tool 扇区水泥胶结测井仪218SL Spectralog 自然伽玛能谱测井219SP Salt-Proximity Surver 自然电位220STAR Simultaneous Acoustic and Resistivity Imager 声电波成像仪221SWC Sidewall Corgun 井壁取心222VSP Vertical Seismic Profile 垂直地震剖面223XMAC Cross Multipole Array Acostilog 交叉多极子阵列声波224ZDL Compensated Z-Densilog 补偿Z-密度测井225AIT Array Induction Imager Tool 阵列感应成像仪226ARI Azimuthal Resistivity Imager 方位电阻率成像仪227HRLA High-Resolusion Laterolog Array Tool 高分辨率阵列侧向仪228FMI(Fullbore Formation Microscan Imager)微电阻率成像仪229IPL Integrated Porosity Lithology 综合孔隙度岩性测井仪230DSI Dipole Shear Sonic Imager 偶极子声波成像仪231CMR Combinable Megnetic Resonance Tool 核磁共振测井232MDT Modular Formation Dynamics Tester 模块式地层动态测试器233LWD Log While Drilling 随钻测井仪器234RAB Resistivity At the Bit 近钻头电阻率仪器235AND Azimuthal Density Neutron Tool 位密度中子仪236CDR Compensated Dual Resistivity 井眼补偿的双电阻率仪器237GST GeoSteering Tool 地质导向仪238CSI Combinable Seismic Imager 组合式地震成像仪1 A blessing in disguise. 塞翁失马(因祸得福)372 a case in point一个恰当的例子3 a close game势均力敌的比赛4 a day in the country郊区一日游5 A faint heart never wine fair lady不入虎穴，焉得虎子6 A faint heart never wine fair lad浪子回头金不换7 A miss is as good as a mile失之毫厘，谬以千里8 a place of interest名胜9 A tower of strength中流砥柱10 a wedding reception结婚宴会11admire to do sth. (美口)很想做某事12after a little过了一会儿13after class下课后14after school放学后15Curie居里(16Custom House海关大楼17Do as you would be done by others己所不欲，勿施与人18do one's bit尽自己的一份力量19January一月20February二月21March三月22April四月23May五月24June六月25July七月26August八月27September九月28October十月29November十一月30December十二月31Monday星期一32Tuesday星期二33wednesday星期三34Thursday星期四35Friday星期五36Saturday星期六admissible error容许误差AND方位密度中子仪data processing center数据处理中心advanced experience（technology）先进经验（技术）geophysical survey地球物理勘探AFP（abnormal formation pressure）异常地层压力after survey calibration summary测后刻度记录after tool check summary测后仪器检查记录after-treatment profile log油井（增产）处理后生产剖面AL block铝块aleurite粉砂aleurolite粉砂岩allowable error容许误差all-wave全波along-track resolution纵向分辨率amass聚积ambient influnence环境影响angular discordance角度不整合angular correction角度校正anisotorpic各向异性的anticline背斜4-arm caliper log四臂井径测井arrival-time curve波至时间曲线attention singal注意信号attenuation衰减；变细；稀释；熄灭，constant常数attitude of rock岩石产状audio logging声频测井，噪声测井 background activIty （correction）本底放射性（校正）back-up curve辅助曲线backup shoe推靠臂bad hole复杂井眼bad earth接地不良big hole大井眼bioarenite生物砂屑岩bioconstructed limestone生物灰岩biolithite(原地)生物灰岩bound water束缚水bow spring centralizer弓形扶正器brine water mud盐水泥浆build-up curve压力恢复曲线build section增斜井段cable continuity电缆通断情况cablehead马笼头cable winch电缆绞车calibrater刻度器calibration summary刻度记录caliper survey井径测量cancel取消;删去casing collar log CCL(套管接箍测井) casing running下套管cased hole套管井chart interpretation图版解释check for zero校对零点check list检验单,总表chloride氯化物clay粘土clayey sandstone泥质砂岩clean sandstone纯砂岩clean out修井compacted formation压实地层company standard企业标准comprehensive evaluation综合评价compression curve压缩曲线computation center计算中心computed log analysis计算机测井分析computed porosity计算的孔隙度conductance传导性dromned水淹的electrode system电极系empirical relationship经验关系error band误差范围normal moveout正常时差oil-bearing formation含油地层oil base油基oil cutting油侵oil-producting formation产油层oil saturation含油饱和度oil sheet薄油层oil shale油页岩oil-water interface油水界面on-site processing（interpretation）现场处理（解释）quicklook interpretation快速解释resistivity log电阻率测井rework返工sonic differential time声波时差master calibration主刻度production log生产井deck甲板masterlog气测carbohydrate碳水化合物carbon dioxide二氧化碳fresh water淡水salinity矿化度2CAL 2-Arm Caliper Log 2臂井径测井3CAL 3-Arm Caliper Log 3臂井径测井4CAL 4-Arm Caliper Log 4臂井径测井AC BHC Acoustilog 声波测井CBIL Circumferential Borehole Imaging Log井周成像测井CBL Acoustic Cement Bond Log 水泥胶结评价测井CDL Compensated Densilog 补偿密度测井CN Compensated Neutron Log补偿中子测井DAC Digital Array Acoustilog 数字阵列声波UBI Ultrasonic Borehole Imager 超声波井眼成像仪senic cycie skipping周波跳跃sea level海平面Sunday星期天。
Electric heating cable 加热电缆field development 油田开发flexible riser 挠性隔水管heating line 加热管线‘host' platform “主"平台‘surface’ conductor “表层”导管“dual bore” type tree “双筒"型采油树“temporary" guide base “临时"导向基座“two stack” approach “双防喷器组”法Abandonment and Recovery 弃置与回收acceptance criteria 验收标准Acceptance Test 验收测试accumulator bottle 蓄能器瓶alignment 找正alternating current 交流电ambient seawater temperature 周围海水温度ambient temperature 环境温度ancillary equipment 辅助设备annular space 环形空间annulus bore 环空孔annulus master valve 环空主阀annulus seal assembly 环空密封总成anti-rotation pin 防旋转销armour wire 铠装线armours layer 铠装层artificial lift 人工举升artificial lift method 人工举升法Asgard project Asgard项目Atmospheric Diving Suit 常压潜水服atmospheric pressure 大气压力attachement point 固着点Austenitic Stainless Steel 奥氏体不锈钢austenitic-ferric steel 奥氏体-铁素体钢auto depth 自动定深automatic connector 自动连接器average unevenness height 平均不均匀高度axial tension 轴向拉力backing steel 背钢backup function 备份功能barrier coating 防护涂层barrier protection 隔层保护basic oxygen furnace 碱性氧气转炉basket storage carousel 篮式存管盘bend limiter 弯曲限幅器bend radius 弯曲半径bend restrictor 弯曲限制器bend stiffener 弯曲加强杆bending loads 弯曲载荷bending moment 弯曲力矩bending reaction ring 弯曲止推环bending stiffness 抗弯刚度bending stress 弯曲应力Billet piercing process 坯板料穿孔工艺bleed valve 泄放阀blind cap 盲帽block valves 断流阀bypass valves 旁通阀Blowout Preventer 防喷器bollard pull 系缆拉力bolt flange connection 螺栓法兰连接bolted flange connection 螺栓法兰连接BOP connector 防喷器连接器BOP pipe ram 防喷器管闸板BOP Stack 防喷器组Bore Protector 井筒保护器bottom crawling vehicle 海底爬行车Buckle propagation 弯曲传播buckle propagation 弯曲传播Bull Nose 圆头管堵bundle 管束buoyancy module 浮力块Campos basin Campos盆地carbon steel 碳钢Carbon steel tube 碳钢管Carbon—Manganese steel pipe 碳锰钢管carrier pipe 输送管Casing Hanger 套管悬挂器casing pup joint 套管短节catenary curve 悬链曲线catenary shape 悬链线型cathodic protection 阴极保护detection system 检测系统Centrifugation Process 离心工艺Check Valve 止回阀chemical fluids 化学流体chemical injection 化学剂注入choke actuator 油嘴促动器choke insert 油嘴嵌件choke position 油嘴位置circuit breaker 断路器circuit length 电路长度circulate hot water 循环热水clad corrosion resistant alloy 复合防腐合金Clad Metal 复合金属clad pipe structure 复合管结构Clad pipe system 复合管系统clamp connector 紧固连接器clamp hub 卡箍Class I 第一类Class II 第二类Class III 第三类Class IV 第四类C—Mn steel pipe 碳锰钢管coating defect 涂层缺陷Coil tubing 连续油管coiled skelp 挠性管材collet connection 套管连接collet connector 套管连接器Completion / Workover Riser System 完井/修井隔水管系统completion equipment 完井设备completion guide base 完井导向基座Completion Guidebase 完井导向基座completion riser system 完井隔水管系统Component Change—Out tool 部件更换工具composite armour 复合铠装composite armour layer 复合铠装层composite material 复合材料compression force 压缩力compressive load 压缩载荷concentric tubing hanger 同心油管悬挂器Conductor Housing 导管头conductor resistance 导体电阻conductor string 导管柱Connection/reaction loads 连接/反作用载荷Connector profile 连接器剖面Continuous lamination 连续分层continuous length 连续长度continuous slab caster 板坯连铸机continuous strand caster 流坯连铸机control cabin 控制舱control fluid 压井液Control Function 控制功能Control junction plate 控制连接板control module 控制模块control pod 控制盒control room 控制室Control Station 控制站control umbilical 控制脐带管control valve 控制阀conventional style trees 常规型采油树Conventional Tree 常规采油树correct orientation 正确方向corrosion allowance 腐蚀裕量corrosion control 腐蚀控制corrosion inhibition 腐蚀抑制corrosion inhibitor 缓蚀剂CORROSION MONITORING 腐蚀监控corrosion protection 腐蚀防护corrosion protection system 腐蚀防护系统corrosion rate 腐蚀速度corrosion resistance 耐腐蚀corrosion resistant alloy 耐腐蚀合金corrosion resistant materials 耐腐蚀材料corrosive agent 腐蚀剂corrosive environment 腐蚀性环境coupler hydraulic 接头液压CROSS SECTION 截面cross sectional area 截面面积Cross Wound Polyethylene 交叉卷绕聚乙烯cross-flow oscillations 横流振动cross-section 截面crushing load 压碎载荷residual strain 残余应变Cumulative strain deformation 累积应变变形cumulative strain 累积应变current drag 海流阻力Current Limiter 限流器current loads 海流载荷current saturation 当前饱和current velocity 海流速度cylindrical billet 圆柱坯料data collection 数据采集data sheets 数据表data transmission 数据传输DC conductor resistance 直流导体电阻Dead Weight 船舶载重量debris cap 岩屑帽deck level 甲板水平面deck load 甲板载荷Deck space 甲板空间deep water 深水deepwater developments 深水开发deepwater field development 深水油气田开发DEEPWATER FIELD DEVELOPMENT REFERENCE BOOK 深水油气田开发参考手册deepwater flowline 深水出油管线deepwater pipeline 深水管道DEEPWATER REFERENCE BOOK 深水参考手册deepwater riser 深水隔水管Destructive Examination 破坏性检验development option 开发方案Differential Global Positioning System 差分全球定位系统Differential Pressure 压力差Digging chain 开挖链direct current 直流Direct Heating System 直接加热系统Directional Control Valve 方向控制阀Distributed Control System 分布式控制系统distribution piping systems 分配管道系统distribution system 配电系统Distribution Unit 分配装置Diving Support Vessel 潜水供应船Dolly base 转管滚座downhole gauges 井下压力计Downhole Pressure 井下压力Downhole Safety Valve 井下安全阀drag loads 拉力载荷drill pipe string 钻杆柱drilling operation 钻井作业drilling riser 钻井隔水管Driving wheel 驱动轮Dual Bore Split Body Tree 双筒拼合本体采油树dual bore subsea tree 双筒水下采油树dual bore tree 双筒采油树dual redundant 双冗余dual SEMs 双SEMDual Systems 双机系统Duplex stainless pipe 双相不锈钢管Duplex stainless steel 双相不锈钢Dynamic analysis 动态分析Dynamic positioning 动力定位dynamic positioning （DP) system 动力定位系统dynamic positioning system 动力定位系统dynamic response 动态响应dynamic riser 动力隔水管dynamically positioned lay vessel 动力定位铺管船Earth continuity test 接地连续性试验Edge trimming 切边edge-crimping 卷边Effective tension 有效张力electric cable 电缆electric current 电流electric heating 电加热electric power 电力Electric Power Unit 电力装置electric pump 电动泵electric resistance welded 电阻焊Electric resistance welded pipe 电阻焊管electric submersible pump 电动潜油泵electrical cable 电缆electrical component 电气部件electrical conductor 电气导线Electrical connection 电气连接electrical connector 电气连接件electrical current 电流Electrical Distribution Unit 配电装置Electrical electrode 电极Electrical Flying Lead 电引线Electrical isolation 电气隔离Electrical Jumper 电气跨接线Electrical junction box 电气接线盒electrical motor 电动机electrical noise 电噪音Electrical penetrators 电动穿孔器Electrical Power Unit 电力装置ELECTRICAL POWER UNIT 电力装置(EPU）electrical pump 电动泵Electrical signal 电信号Electrical Umbilical 电气脐带管electric—arc furnace 电弧炉electric—welded pipe 电焊接管electro—hydraulic control systems 电动液压控制系统electro-hydraulic multiplexed subsea control system 电动液压多路复用水下控制系统Electro—hydraulic umbilical 电动液压脐带管electronic components 电子元件Emergency Shut Down 应急关断empirical curve 经验曲线empirical uplift coefficient 经验上提系数end fitting 端部配件end riser termination 端部隔水管终端environment loads 环境载荷environmental condition 环境条件environmental loads 环境载荷ERW line pipe 电阻焊管线ESD sequence 应急关断顺序ESD signal 应急关断信号export line 输送管线external corrosion 外部腐蚀external diameter 外径external hydrostatic pressure 外部静水压力external pressure 外部压力External Welding 外部焊接Extrusion Process 挤压工艺Extrusion throat 挤压式喉管fabrication 制造fabrication times 制造时间Factory Acceptance Test 工厂验收试验fatigue damage 疲劳损坏fatigue life 疲劳寿命female connector 母连接器female couplers 母接头female couplings 母接头fibre optic 光纤fibre optic cables 光纤电缆fibre optic technology 光纤技术field development 油气田开发field joint 现场连接接头deepwater，reference，terms分享到: QQ空间腾讯微博腾讯朋友新浪微博人人网豆瓣更多.。
REPORT NO.DATEOPERATORCONTRACTORSIGNATURE OF OPERATOR'S REPRESENTATIVE RIG NO.WELL NO.LAST CSG. TBG. OR LINERSIZEMAKEWT.&GR.NO.JOINTMETERRKB. TO CSG. HD.SET AT.WIRE LINE RECORDREEL NO.SIZENO.LINESMT.SLIPPEDMT.CUT OFFPRESENT LENGTHTON KIMT. OR TRIPS SINCE LAST CUT CUMULATIVE TON KIMT. OR TRIPSP PRSPUMP NO.LINER SIZEFLOE RATE(LPS)MTD. RUN(METHOD RUN)SGL.(SINGLE)PARALLELDEV.DIR.TVD.HORZ. DISP(HORIZONTAL DISPLACEMENT) TIME LOGELAPSED TIMECODE NO.DETAILS OF OPERATION IN SEQUENCE REMARKNAMEDRILLERASST. DRILLERDRKMAN(DERRICKMAN)FLRMAN(FLOORMAN)MOTORMANRSTABOUT(ROUSTABOUT)D.P.SIZE/WT.-FT/GRADETOOL JT. OD.(TOOL JOINT OUTSIDE DIAMETER) STRING NO.PUMP NO.PUMP MANUFACTURERTYPESTROKE LENGTHTIME DISTRIBUTION-HOURSCODE NO.-OPERATIONNIGHTDAYRIG UP AND TEAR DOWNDRILL ACTUALREAMINGCORINGCONDITION MUD AND CIR.TRIPSLUBRICATE RIGREPAIR RIGCUT OFF DRILLING LINE DEVIATION SURVEYWIRE LINE LOGSRUN CASING AND CEMENT WAIT ON CMT.NIPPLE UP B.O.P.TEST B.O.P.DRILL STEM TESTPLUG BACKSQUEEZE CEMENT FISHINGDIR. WORKTOTALPERFORATIONTBG TRIPSTREATINGSWABBINGTESTINGADDITIONALDAY WORK TIME SUMMARY OFFICE USE ONLYHRS. W/CONTR.D.P.HRS. W/OPR.D.P.HRS. WO/D.P.HRS.STANDBYTOTAL DAY WORK DRILLING ASSEMBLYBITSTANDS D.P.SINGLES D.P.KELLY DOWNTOTALWEIGHT OF STRINGBIT RECORDBIT NO.SIZELADC CODEMFG(MANUFACTURING) TYPEJETSDEPTH OUTDEPTH INTOTAL FOOTAGETOTAL HOURSCUTTING STRUCTURE INNEROUTERDULL CHAR.(CHARACTER) LOCATIONBEAR/SEALSGAGEREASON PLD.(PULLED) MUD RECORDTIMEWEIGHTPRESSURE GRADIENT VISC.PV/YPGELSWL.PHSOLIDS%MUD AND CHEMICAL ADDED TYPEAMT.(AMOUNT)NO.OF DAYS FROM SPUD CUMULATIVE ROTATING HOURS TOTAL MUD COSTWELLRIGSPUDRIG COST/HOURBIT DATARUN NO.BIT NO.BIT SIZEBIT MAKEBIT TYPESERIAL NO.IADC CODEbit costdepth indepth outdrilled intervalbit performancerotat. Hoursrop(m/hr)tripping hoursavg.wobavg.rpmavg.torquecost/ftbit dull gradingcutting structramarkshydraulic datarun no.jets sizeT.F.A.Flow rate(l/s)st.pipe pressure(Mpa)BIT HHPBIT HISJETS VEL.(M/SEC.)ANNULUS VEL.MUD DATAmud typemud weight(kg/cm3)mud visc.(cp)mud y.p.(pa)DIRECTIONALDEPTHINCL.(inclination)AZ.(azimuth)LITHOLOGY FORMATION TOPS REMARKSTOOLPUSHER'S SIGNATURE编号日期作业者（甲方）承包者甲方代表签名钻机编号井号截止到当日该井已下入的套管，油管或尾管数据尺寸厂家每米重量和钢级根数总长转盘面至套管头顶部长度（联入）下深大绳记录现用大绳滚筒编号尺寸大绳股数该次倒大绳米数该次割掉大绳米数筒上大绳现存长度自上次倒大绳后大绳完成的公里数或起下钻次数该筒大绳完成的总吨公里数或起下钻次数钻盘每分转数泵编号钢套尺寸排量运行方式单泵双泵井斜角方位角垂深水平位移时间记录所用时间编号按时间顺序作业内容异常情况或必要提示姓名司钻副司钻井架工钻工机房工场地工钻杆尺寸/每米重量/钢级钻杆接头外径钻杆数量泵数量泵生产厂家泵型号泵冲程长度时效分析栏作业内容-分类编号夜班白班安装和拆卸纯钻进扩眼取心循环与处理泥浆起下钻钻机保养钻机修理倒大绳测斜测井下套管，固井候凝安装封井器封井器测试中途测试打水泥塞挤水泥打捞定向合计射孔起下油管处理抽吸测试其他时间日工作时间分类小结仅供办公室使用使用承包商钻杆工作时间使用作业方（甲方）钻杆工作时间未使用钻杆工作时间组织停工时间合计工作时间钻具结构钻头钻杆立柱数钻杆单根数（余1OR2）方入合计悬重钻头记录钻头序号尺寸国际钻井承包商协会给予钻头的编号厂家类型水眼尺寸起出井深下入井深总进尺该钻头入井至今总时间钻头起初后对钻头情况的描述内排齿情况外排齿情况主要钝化特征磨损位置轴密封情况钻头外径起钻原因泥浆记录时间密度泥浆液柱压力梯度粘度塑性粘度/屈服值切力失水PH值含沙加入泥浆和药品类型加重开钻至今天数累计钻进小时开钻至今泥浆费用井号钻机编号开钻日期钻机使用每小时费用钻头数据该井钻头序号该井使用钻头按顺序编号钻头尺寸钻头厂家钻头类型钻头系列号国际承包商协会给予钻头的编号钻头成本钻头下入井深钻头起出井深钻头进尺钻头使用情况钻头在井底使用情况钻头机械速度起下钻换钻头时间平均钻压平均钻盘转速平均钻进扭矩该钻头单位进尺成本钻头磨损级别切削结构备注ramakes水力参数同‘BIT NO.’水眼尺寸钻头总喷面积排量力管压力钻头水马力比水马力喷射速度环空返速泥浆数据泥浆类型泥浆密度泥浆粘度屈服值井斜情况井深起钻井斜度方位所钻地层顶界深备注井队长签字。
REPORT NO.DATEOPERATORCONTRACTORSIGNATURE OF OPERATOR'S REPRESENTATIVE RIG NO.WELL NO.LAST CSG. TBG. OR LINERSIZEMAKEWT.&GR.NO.JOINTMETERRKB. TO CSG. HD.SET AT.WIRE LINE RECORDREEL NO.SIZENO.LINESMT.SLIPPEDMT.CUT OFFPRESENT LENGTHTON KIMT. OR TRIPS SINCE LAST CUT CUMULATIVE TON KIMT. OR TRIPSP PRSPUMP NO.LINER SIZEFLOE RATE(LPS)MTD. RUN(METHOD RUN)SGL.(SINGLE)PARALLELDEV.DIR.TVD.HORZ. DISP(HORIZONTAL DISPLACEMENT) TIME LOGELAPSED TIMECODE NO.DETAILS OF OPERATION IN SEQUENCE REMARKNAMEDRILLERASST. DRILLERDRKMAN(DERRICKMAN)FLRMAN(FLOORMAN)MOTORMANRSTABOUT(ROUSTABOUT)D.P.SIZE/WT.-FT/GRADETOOL JT. OD.(TOOL JOINT OUTSIDE DIAMETER) STRING NO.PUMP NO.PUMP MANUFACTURERTYPESTROKE LENGTHTIME DISTRIBUTION-HOURSCODE NO.-OPERATIONNIGHTDAYRIG UP AND TEAR DOWNDRILL ACTUALREAMINGCORINGCONDITION MUD AND CIR.TRIPSLUBRICATE RIGREPAIR RIGCUT OFF DRILLING LINE DEVIATION SURVEYWIRE LINE LOGSRUN CASING AND CEMENT WAIT ON CMT.NIPPLE UP B.O.P.TEST B.O.P.DRILL STEM TESTPLUG BACKSQUEEZE CEMENT FISHINGDIR. WORKTOTALPERFORATIONTBG TRIPSTREATINGSWABBINGTESTINGADDITIONALDAY WORK TIME SUMMARY OFFICE USE ONLYHRS. W/CONTR.D.P.HRS. W/OPR.D.P.HRS. WO/D.P.HRS.STANDBYTOTAL DAY WORK DRILLING ASSEMBLYBITSTANDS D.P.SINGLES D.P.KELLY DOWNTOTALWEIGHT OF STRINGBIT RECORDBIT NO.SIZELADC CODEMFG(MANUFACTURING) TYPEJETSDEPTH OUTDEPTH INTOTAL FOOTAGETOTAL HOURSCUTTING STRUCTURE INNEROUTERDULL CHAR.(CHARACTER) LOCATIONBEAR/SEALSGAGEREASON PLD.(PULLED) MUD RECORDTIMEWEIGHTPRESSURE GRADIENT VISC.PV/YPGELSWL.PHSOLIDS%MUD AND CHEMICAL ADDED TYPEAMT.(AMOUNT)NO.OF DAYS FROM SPUD CUMULATIVE ROTATING HOURS TOTAL MUD COSTWELLRIGSPUDRIG COST/HOURBIT DATARUN NO.BIT NO.BIT SIZEBIT MAKEBIT TYPESERIAL NO.IADC CODEbit costdepth indepth outdrilled intervalbit performancerotat. Hoursrop(m/hr)tripping hoursavg.wobavg.rpmavg.torquecost/ftbit dull gradingcutting structramarkshydraulic datarun no.jets sizeT.F.A.Flow rate(l/s)st.pipe pressure(Mpa)BIT HHPBIT HISJETS VEL.(M/SEC.)ANNULUS VEL.MUD DATAmud typemud weight(kg/cm3)mud visc.(cp)mud y.p.(pa)DIRECTIONALDEPTHINCL.(inclination)AZ.(azimuth)LITHOLOGY FORMATION TOPS REMARKSTOOLPUSHER'S SIGNATURE编号日期作业者（甲方）承包者甲方代表签名钻机编号井号截止到当日该井已下入的套管，油管或尾管数据尺寸厂家每米重量和钢级根数总长转盘面至套管头顶部长度（联入）下深大绳记录现用大绳滚筒编号尺寸大绳股数该次倒大绳米数该次割掉大绳米数筒上大绳现存长度自上次倒大绳后大绳完成的公里数或起下钻次数该筒大绳完成的总吨公里数或起下钻次数钻盘每分转数泵编号钢套尺寸排量运行方式单泵双泵井斜角方位角垂深水平位移时间记录所用时间编号按时间顺序作业内容异常情况或必要提示姓名司钻副司钻井架工钻工机房工场地工钻杆尺寸/每米重量/钢级钻杆接头外径钻杆数量泵数量泵生产厂家泵型号泵冲程长度时效分析栏作业内容-分类编号夜班白班安装和拆卸纯钻进扩眼取心循环与处理泥浆起下钻钻机保养钻机修理倒大绳测斜测井下套管，固井候凝安装封井器封井器测试中途测试打水泥塞挤水泥打捞定向合计射孔起下油管处理抽吸测试其他时间日工作时间分类小结仅供办公室使用使用承包商钻杆工作时间使用作业方（甲方）钻杆工作时间未使用钻杆工作时间组织停工时间合计工作时间钻具结构钻头钻杆立柱数钻杆单根数（余1OR2）方入合计悬重钻头记录钻头序号尺寸国际钻井承包商协会给予钻头的编号厂家类型水眼尺寸起出井深下入井深总进尺该钻头入井至今总时间钻头起初后对钻头情况的描述内排齿情况外排齿情况主要钝化特征磨损位置轴密封情况钻头外径起钻原因泥浆记录时间密度泥浆液柱压力梯度粘度塑性粘度/屈服值切力失水PH值含沙加入泥浆和药品类型加重开钻至今天数累计钻进小时开钻至今泥浆费用井号钻机编号开钻日期钻机使用每小时费用钻头数据该井钻头序号该井使用钻头按顺序编号钻头尺寸钻头厂家钻头类型钻头系列号国际承包商协会给予钻头的编号钻头成本钻头下入井深钻头起出井深钻头进尺钻头使用情况钻头在井底使用情况钻头机械速度起下钻换钻头时间平均钻压平均钻盘转速平均钻进扭矩该钻头单位进尺成本钻头磨损级别切削结构备注ramakes水力参数同‘BIT NO.’水眼尺寸钻头总喷面积排量力管压力钻头水马力比水马力喷射速度环空返速泥浆数据泥浆类型泥浆密度泥浆粘度屈服值井斜情况井深起钻井斜度方位所钻地层顶界深备注井队长签字。
专业录井、钻井词汇英汉对照1. DRILLING ENGINEERING 钻井工程1.1 THE COMPENTS OF THE ROTARY DRILLING RIG钻机系统的组成1.1.1 Hoisting System 提升系统sub structure 井架底座，底部结构derrick (mask) 井架crown block 天车traveling block 游动滑车wire line (drill line) 钢丝绳，钻井大绳deadline死绳air hoist气压提升机，气压提升绞车drilling rig (drilling machine) 钻机drawwork绞车drum滚筒brake crank (handle, bar) 刹把hydraulic brake水刹车electric brake 电磁刹车mechanical friction device 机械磨擦装置cathead猫头elevator吊卡slip type casing elevator卡瓦型套管吊卡pipe elevator 钻杆吊卡 slip卡瓦safety slip 安全卡瓦collar rotary slip 环形钻铤转盘卡瓦drill pipe rotary slips 环形钻杆转盘卡瓦links连杆hook大钩hook load 大钩负荷 hook speed 大钩速度hook weight大钩悬重DF (drill floor) 钻台monkey board 二层台1.1.2 Circulating & Solids Control System 循环及固控系统drilling mud (drilling fluid) 钻井泥浆，钻井液water mud 淡水泥浆 water-base mud水基泥浆salt mud 盐水泥浆salt-base mud盐水基泥浆oil-base mud 油基泥浆oilemuision 油包水泥浆，石油乳浊液mud property 泥浆性能 mud weight out/in 泥浆密度进/出mud density out/in 泥浆密度进/出mud viscosity 泥浆粘度 mud conductivity 泥浆电导率mud resistivity 泥浆电阻 PH-value PH值water loss 失水 sand content 含砂量 gel strength 静切力mud cake 泥饼mud cake effect泥饼效应mud filtrate 泥浆滤液mud loss 泥浆漏失mud column 泥浆液柱mud sample 泥浆试样mud stability泥浆稳定性mud pump (pump) 泥浆泵pump body 泵体 pump capacity (discharge) 泵排量（泵容量） pump displacement泵排量pump output 泵排量pump efficiency 泵效率pump stroke 泵冲程pump cylinder 缸套mud pump rod 泥浆泵拉杆piston活塞mud room泵房mud lin浆管线choke line 地面管汇high pressure line 高压管线standpipe立管standpipe valve 立管闸门hose水龙带swivel水龙头swivel bail 水龙头吊环 swivel sub (joint) 水龙头接头swivel stem 水龙头中心管goosenec颈管wash pipe冲管wash pipe swivel 冲管旋转接头kelly方钻杆kelly cock 方钻杆上旋塞kelly dog nut 方钻杆下旋塞HWDP height weight drillpipe 加重钻杆DP drillpipe 钻杆DC drill collar 钻铤spiral collar螺旋钻铤pony DC (collar) 短钻铤NMDC non-monel collar 无磁钻铤tool join头sub (joint) 接头tool joint box 接头母扣tool joint pin 接头公扣X-O (crossover) subs 配合接头（转换接头）shock sub 减震接头bumper sub 缓冲器接头bit sub钻头接头flex sub 柔性短接string stabilizer (pin ×box) 钻具扶正器（公扣对母扣）near bit stabilizer (box ×box) 扶正器（母扣对母扣） centrallizer 扶正器bumpers (shock absorber) 减震器drilling junk basket 随钻打捞杯drilling jar 随钻震击器jar震击器BHA bottomhole assembly 下部钻具总成HDRT high data rate tool 高速数据传输钻具（M WD用）drill stem (drill string) 钻柱bit钻头drag bit (blade bit) 刮刀钻头cone bit (roller bit) 牙轮钻头 tri-cone bit 三牙轮钻头jet bit 喷射式牙轮钻头core drilling bit 取心钻头 milled tooth bit 铣齿钻头 insert bit 镶齿钻头gauge insert bit 保径镶齿钻头diamond bit 金刚石钻头bit cone 钻头牙轮bit size 钻头尺寸bit cost 钻头成本bit record 钻头记录bit type 钻头类型bit jets 钻头水眼bit nozzle 钻头喷嘴TFA total flow area 钻头水眼总流量面积bit consumption 钻头用量bit footage 钻头进尺 bit factor 钻头因素bit grading 钻头磨损等级bit-tooth dullness 钻头牙齿磨钝程度bit life 钻头寿命bit HHP hydraulic horsepower 钻头水马力hole opener 扩眼器underreamer 管下扩眼器annular 环空wellhead 井口flowline 架空管线shale shaker 震动筛mud tank (mud pits) 泥浆罐suction pit 进口罐setting pit 沉砂罐waste pit 泥浆坑desander 除砂器desilter 除泥器degasser 除气器mud cleaner 清洁器centrifuge 离心机agitator 搅拌机1.1.3 Rotary System 旋转系统prime mover 原动机 diesel engine 柴油机engine 引擎rotary table 转盘rotary base 转盘底座rotary chain 转盘传动链条 KB kelly bushing 方钻杆补心roller type bushing滚子方补心master bushing 转盘补心slip type casing spider 卡瓦型套管卡盘tongs 大钳，吊钳lead tongs 内钳back-up tongs 外钳hydraulic tongs 液压大钳chain tongs 链钳pipe tongs (spanner) 管钳spinning chain 旋链power tongs 动力大钳spanning wrench 旋转扳手1.1.4 Blowout Prevention System 防喷系统kick井涌blowout井喷blowout control 井控blowout control equipment井控设备blowout hookup 防喷装置BOP blowout prevention 防喷器annular ram prevention （万能）环形防喷器pipe rams （半封）闸板防喷器 blind rams 盲板全封式防喷器 shear rams 剪切闸板式全封防喷器blowout plug 防喷塞blowout preventer of three stage packer 三级密封式防喷器control console 控制台remote control console 远程控制台conductor line 导管choke line manifold 节流管线fill line 灌浆管线kill line 压井管线emergency line 紧急压井管线chokes节流阀hydraulic valve 液压阀gas buster 泥气分离器poor boy 泥气分离器choke pressure 节流压力blowout prevention procedure 防喷措施1.1.5 Motion Compensation System 运动补偿系统offshore floating rigs 海上浮式钻机drillstring compensator 钻柱补偿器sea level海平面sea floor海底deck甲板air pressure vessels 空气压力容器hydraulic cylinder assembles 液压缸总成piston rod 活塞杆standard hook assembles标准大钩总成riser隔水导管guideline tensioner 导索拉紧装置control panel 控制盘 guide base 导引底盘marine riser 海中隔水导管 moon pool 月形开口riser tensioner 隔水导管拉紧装置1.2 WELLS & DRILLING CRAFT 井与钻井工艺流程well, drilling well 井，钻井 wildcat well 预探，初探井delineation well 探边井 development well 生产井，开发井 satellite well 丛式井 injection well 注水井 direction well 定向井 deviation well 斜井 COST continental offshore stratigraphic test well（美）大陆近海地层探井to rig up 安装（钻机）to install the equipment 安装设备to get drill pipes in order 排钻具to measure & inspect drillstring仗量，检查钻具to measure the length of drill pipes &drill collars 量钻杆，量钻铤to nipple up BOP 装封井器 to spud in 开钻to turn on the pumps 开泵to circulate, circulation 循环circulate to the bottom up 完全循环reserve circulation 反循环bit break-in procedure 磨合钻头reaming扩眼drilling钻进coring drilling 取心钻进rough drilling (bouncing of drilling tool) 跳钻bit bouncing 蹩钻reverse rotation (running) 打倒车correct drift 纠斜 lost circulation 井漏 slough (cave-in) 井塌 to stop the pump 停泵 PC pipe connection 接单根make a joint 接单根 wire line survey 吊测deviation survey 测斜 to change the shaker screen 换筛布to repair the pump 修泵to break down a joint 卸一个单根to slug the pipe 往钻杆内打重泥浆POOH to pull out of hole 起钻to trip out the hole 起钻touch sticking 遇卡pulling a piston 拔活塞 to lubricate rig (drawwork) 保养钻机（绞车）to repair rig 维修钻机to cut & slip the drillline 倒大绳to clean the mud tank 清罐well logging, E-log 电测SWC sidewall coring 井壁取心DST drill stem test 钻杆中途测试 to running casing, casing 下套管surface casing 表层套管intermediate casing 技术套管liner尾管to running cementing 固井to squeeze cement 挤水泥 WOC wait on cement 侯凝to nipple up BOP 换装封井器 to install the BOP 装封井器 to test BOP 封井器试压to change bit, bit change 换钻头RIH run in hole 下钻to trip in 下钻 touchdown, touching resistance 遇阻RTO round trip operation 起下钻作业short tripping 短起下钻reaming划眼to cement plug , plug back 打水泥塞side tracking 侧钻to kick off 造斜KOD kick off depth 造斜深度KOP kick off point 造斜点to hang up 意外停机to survey the flowout 监测溢流flow check 溢流检查WOO wait on order 等指令WOW wait on weather等天气WOL wait on logging 等测井WOE wait on equipment 等设备WOFT wait on fishing tools等打捞工具to finish drilling 完钻to running the liner 挂尾管to plug-back 填井 final testing 完井测试to install the Chirstmas tree (production) 装采油树well completion 完井to prevent sticking 防卡to prevent caving 防塌to prevent loss of circulation 防漏to prevent blowout 防喷1.3 SPECIAL ENGINEERING OPERATION 特殊工程施工Coring取心1.3.1.1 Coring Equipment 取心及岩心分析设备coring drill 取心钻具 core drilling bit 取心钻头core bit 取心钻头coring crown 金刚石取心钻头 core cone bit 牙轮取心钻头 core basket 岩心爪 core barrel catcher 岩心抓取器core catcher 岩心爪 core catcher case 岩心爪外套core gripper 岩心爪 core-gripper with slip 卡瓦式岩心爪core-gripper with slipcollar 卡箍式岩心爪core-gripper with slipspring 卡簧式岩心爪core spring 岩心卡簧core barrel 岩心筒 core container 内岩心筒 core chamber 岩心室core barrel head 岩心筒上盖core barrel ring 取心筒垫圈core shoe （压力式）取心筒鞋core plunger 岩心推取杆 core pusher 岩心推取塞 core fisher 井底岩心打捞器core picker 落井岩心打捞器core bag 岩心袋core box 岩心盒core tray 岩心盒core house 岩心存储室core storage 岩心库core library 岩心库core breaker 岩心切断器 core slicer (splitter) 岩心切断器core-drying oven 岩心烘箱core cutter 岩心切片机core distillation apparatus 岩心蒸馏仪core interpreting device 岩心分析仪core laboratory 岩心分析实验室1.3.1.2 Core Drilling Operation 取心钻进作业core hole 取心井core boring 取心钻进core drilling 取心钻进cored-up mould 岩心造型coring depth 取心井深coring footage (run) 取心进尺coring weight 取心钻压 coring formation 取心地层 core grouting 取心被卡core breaking 割断岩心core breaking by hydraulic pressure 投球液压割心core breaking by mechanical loading 机械加压割心1.3.1.3 Core Analysis 岩心分析core-analysis data 岩心分析数据core data 岩心数据core log 岩心录井core graph 岩心图core cross section 岩心横剖面 core-description graph 岩心描述图core sample 岩心样core orientation 岩心方向 core inlet face 岩心入口面core outlet face 岩心出口面core diameter 岩心直径core intervals 取心井段 core footage (run) 取心进尺core recovery 岩心收获率 core porosity 岩心空隙度 core oil saturation 岩心含油饱和度 core permeability 岩心渗透率1.3.2 Directional Well Drilling & Deviation Survey 定向钻井和井斜监测directional well 定向井 directional hole 定向井directional drilling 定向钻井directional drilling contractor定向井承包商directional MWD 定向随钻测量directional drill tool 定向钻井工具 directional orientation tool 定向工具the steering tool 定向工具deflecting tool 造斜工具 directional-survey tool 定向测量工具direction finder 测向仪direction instrument 方向仪directional tool (steering tool) 随钻测斜仪inclinometer 测斜仪 single shot inclinometer 单点测斜仪syphon inclinometer 虹吸测斜仪continuous inclinometer 连续测斜仪gyroscope 陀螺仪pendulums (plumb bob) 测棰magnetic compass 磁螺盘directional turbodrill 定向涡轮钻具directional bit 定向钻头 directional-type tricone bit定向三牙轮钻头directional clinograph 方位测斜仪deviation replot 井斜图 side track 定向设计剖面图horiz projection 水平投影图 vertical projection 垂直投影图projection on a vertical plane 垂直面上的投影图deviation map 井斜图 perspective view 透视图3 dimensions visualisation三维空间透视图directional diagram 方位图deviation report 井斜报告directional data 井斜数据surveys 井斜数据deviation measurement data 井斜测量数据directional line 方向线main direction 主方向E.W.S.N 东，西，南，北directional control 方位控制directional characteristics 方位特征directional accuracy 方向性精度directional elements 定向要素direction parameter 方位参数horizontal plane 水平面vertical plane 垂直面directional angle 方位角the drift angle 井斜角the azimuth 方位角bearing (north) 方位角angle of projection投影角desired drift angle 设计的造斜角the bottom hole coordinate 井底坐标coarse coordinates 水平位移坐标the vertical depth 垂直深度KOD kick off depth 造斜深度end off deviation vertical depth 稳斜结束时的垂直深度end kick off vertical depth 结束造斜时的垂直深度final re-entry depth 恢复点的深度average angle method 平均角度法radius of curvature method 曲率半径法KOP kick off point 初试造斜点end of kick off 造斜终点end of deviation 斜井段终点re-entry point 返直点dog leg 井斜度，狗腿角dog leg scale 狗腿度比例dog leg severity 狗腿严重程度angle build up 增斜angle drop off 降斜dog leg at kick off point增斜率dog leg at re-entry point 降斜率the actual well path 井眼轨迹1.3.3 Casing 下套管casing套管casing joint 套管单根，一节套管casing starter 入井第一节套管 casing nipple 套管短节casing string 套管柱casing tally 套管记录 casing type 套管类型casing weight 套管重量 casing size 套管尺寸casing diameter 套管直径casing length 套管长度casing volume 套管容积casing grade 套管钢级casing depth 套管深度casing setting depth 套管下入深度casing accessories (hardware) 套管附件casing guide shoe 引鞋casing float shoe 套管鞋casing shoe depth 套管鞋深度casing centralizer 套管扶正器casing collar 套管接箍 casing check valve 回压凡儿casing float (collar) 回压凡儿casing sub 套管异径接头casing head 套管头casinghead spool 套管头四通casing landing 联顶节casing job下套管作业casing running(installation) 下套管casing-bearing formation好套管下入地层casing appliances 下套管工具casing connection套管连接casing elevator 套管吊卡casing slip 套管卡瓦casing spider 套管卡盘式吊卡casing suspender 套管悬挂器casing hanger 套管悬挂器casing screw protector 套管公扣护丝casing screw head 套管母扣护丝casing seal 套管密封件casing annular 套管环空casing-to-hole annular 套管井壁环空casing pressure 套管压力casing head pressure 套管头压力casing pressure test套管试压casingless completion裸眼完井casing inspection 套管探伤casing programme 套管程序casing severing 割套管casing sticking 套管被卡casing wear 套管磨损casing split 套管裂纹casing leak 套管漏casing imperfection套管缺陷casing failure 套管损坏casing damage 套管损伤casing deformation套管变形casing corrosion 套管腐蚀casing collapse 套管挤坏casing buckling 套管弯曲casing bridge plug套管桥塞casing bowl 套管打捞筒casing collar location 套管接箍测定器casing corrosion monitoring 套管腐蚀监测casing knife 套管割刀casing mandrel 胀管器casing mill 套管铣鞋casing packer 套管封隔器casing perforator 套管射孔器casing section mill 套管铣刀casing splitter 套管割刀casing withdrawal 拔套管1.3.4 Well Cementing 固井open hole 裸眼井cased hole 套管井pocket口袋the pocket volume 口袋体积normal volume 正常体积extra volume 额外体积hole description 井眼描述string / casing description 钻柱和套管描述surface cement line description 地面水泥管线描述cement 水泥number of sacks 水泥袋数cement factor 水泥系数 volume of the cement 水泥体积cement mark 水泥标号 cement brand 水泥牌号cement filtrate 水泥滤液cement slurry 水泥浆 cement paste 水泥浆cement milk 水泥浆 slurry in string 钻柱内水泥浆cement slurry volume 水泥浆体积（用量）slurry excess 水泥浆余量 slurry density 水泥浆密度 cement column 水泥浆液柱cement consistency 水泥浆稠度cement flow 水泥浆液流cement additive 水泥添加剂additive name 添加剂名称bentonite 膨润土additive volume 添加物体积cementer 粘结剂 cement accelerator 水泥促凝剂cement hardener 水泥速凝剂cement agent 粘结剂 cement concrete 水泥混凝土cement-water ratio 水灰比cement operation (jobs)固井作业cement method 固井方法first stage cementation一级注水泥two stage cementation 二级注水泥multi-stage cementation 多级注水泥liner cementation 衬管注水泥cement equipment (unit)固井设备cementing tool 固井工具 cementing pump 固井泵cementing pump skid 撬装注水泥泵组cementing tank 水泥罐cement blender 水泥搅拌器cement mixer 水泥搅拌器 cement practice 固井施工cement squeeze work 挤水泥作业cementing formulation 注水泥配方cement point 封固段 cementing through 全井封固seal liquid (spacer fluid) injection 注隔离液cementing injection 注水泥浆chasing 替浆cement displacement 替浆cementing reaction 胶结反应cement setting 水泥凝固cement curing time 水泥候凝时间cementing strength 水泥强度cemented up 注完水泥。
钻井常用术语英汉对照汉语英语汉语英语井位Contract Area动塑比PV/YP井号Well Name初终切Gel 0/10承包商Contractor失水Water Loss设计井深T.D.pH值pH天气情况Weather固相含量Solids日期Date成分Comments钻井日报Daily Drilling Report泥浆泵参数Mud Pump Output and Hydraulics+A53钻机编号Rig No泵号Pump #上报时间Activity @ Report Time类型Model现井深Depth @ noon冲数Stroke起始井深Previous Depth缸套直径Liner日进尺Meterage/Footage套管及固井Casing and Cementing开钻天数Days Since Spud套管尺寸Casing Size时间情况Time Distribution总数Total JTS自From总长Length到To总重Weight小时Hours钢级Grade工作内容Description of Operations扣型Thread钻井监督Representative范围Range安全提示Safety meeting下深Shoe @明日计划forward plan其它信息Other information钻头报告Bit Record测斜情况Surveys钻头号Bit No.井深Depth尺寸Bit Size井斜角Angle厂家MFG.悬重String Weight类型Type井场钻具数量Tubulars on Location序列号Ser. No.方位Azim水眼Jets测深TVD进尺Meters井斜Dev钻头时间Bit Hrs.取心井段coring depth机械钻速MPH心长core longth地层Drillig收获率recovery钻压W.O.B下深102.39米on bottom at 102.39m转速RPM钻井队drilling team封井器BOP固井公司cementing泥浆报告Mud Report录井公司mud logging采样时间Time电测队wireline logging密度 (g/cm3)Den (g/cm3)胜利定向井directional engineer粘度 (s)Vis (s)晴Sunny & warm开钻准备prepare to spud.钻进drilling循环circulate circulating短起下3柱make a 3 stand trip起钻POOH.下套管run casing .landed CSG固井do cement job .侯凝waiting on cement.封井器试压test BOP.检修repair the instrument等电测waiting for the wireline logging team.电测wireline logging.通井run in hole.cir.and pull out of the hole.二开准备prepare to the second spud.下钻make in hole.钻水泥塞drill cement plug.测斜make a survey.取心钻进coring割心cut core.出心take out the core划眼ream from固井后测井wireline logging三开准备prepare the third spud.检修maintenance rig低压钻进drilling with low WOB修泵repair pump发电机generatorA53。
钻井工程术语Terms of well drilling engineering2钻井总论 general2.1井的基本概念basic concept of a well井well ，井口wellhead，井底hole bottom，裸眼open-hole，井深well depth，井壁well wall，annulus井眼轴线hole axis:井眼的中心线，井身结构casing program2.2井的类别well type:探井exploratory well，开发井development well，直井straight well3钻井方法drilling method:顿钻钻井cable tool drilling:，杆式顿钻rod tool drilling，绳式顿钻cable drilling，旋转钻井rotary drilling，转盘钻井rotary drilling，顶部驱动钻井top drive drilling，井底动力钻井down hole motor drilling，涡轮钻井turbo-drilling，螺杆钻井Dyna-drilling，电动钻井electric drilling:2.4钻井种类kinds of drilling海上钻井offshore drilling，沙漠钻井desert drilling，清水钻井water drilling，空气（天然气）钻井air(gas) drilling，泡沫钻井foam drilling，雾化钻井mist drilling，充气钻井液钻井aerated drilling fluid drilling，平衡压力钻井balanced pressure drilling，欠平衡压力钻井under-balanced drilling，近平衡压力钻井near balanced drilling，小井眼钻井slim hole drilling，取芯钻井core drilling，2.5工程报废井engineering abandoned well2.6钻井设计well design2.7单井工程设计engineering design of a single well2.8钻井工程质量drilling engineering quality2.9钻井工序drilling process2.10钻井进度drilling progress2.11钻井条件drilling condition3岩石的物理机械性质及可钻性rock physical mechanical properties and drillability3.1岩石的物理机械性质rock mechanical properties:矿物的微硬度mineral micro-hardness，岩石的微硬度rock micro-hardness，岩石的硬度rock hardness，肖氏岩石硬度Shore's hardness，岩石的筒形抗内压胀烈试验hollow cylinder burst test:，岩石的常规抗压缩强度rock compressive strength，岩石的捣碎法压缩试验crashing compression test for rock，岩石的抗压入破碎强度rock fragmenting strength，压模静压入static impact test，压力面pressure face，等剪应力球面iso-shear sphere，压模压入岩石时的变形曲线force-penetration curve，动压入(冲击压入) impact penetration，岩石的抗剪切强度rock shear strength，岩石的抗剪切强度试验rock shear testing，三轴应力状态tri-axial stress state，岩石的三轴强度试验tri-axial compressive test of rock，岩石的常规三轴试验conventional triaxial test of rock，岩石的真三轴试验true triaxial test of rock，脆性岩石brittle rock，岩石的塑性rock plasticity，塑性岩石plastic rock，岩石的塑性变形rock plastic deformation，，岩石的假塑性破坏rock pseudo-plastics breakage，，岩石的塑性系数rock plasticity coefficient，岩石脆塑性转变压力(临界压力) rock brittle-plastic transition pressure，岩层蠕变strata creep，岩石的库仑-纳维尔强度准则Coulomb-Navier strengthcriterion for rock，岩石的莫尔强度准则Mohr failure criterion for rock，岩石的格里菲斯脆性破坏准则Griffith theory for rock brittle failure，统计强度理论statistical strength theory，破碎机理crushing mechanism，单齿压入试验single tooth penetration test，破碎坑cruched crater，破碎接触压力fracture contact pressure，牙轮钻头承压面积bit bearing area，岩石的表面破碎rock surface fracture:，岩石的疲劳破碎rock fatigue fracture，岩石的体积破碎rock volumetric fracture，岩石的单位体积破碎功rock specific volumetric fragile work，地温梯度geothermal gradient，地温级度geothermal step，高导热系数层high thermal conductivity strata，地应力in-situ stress，岩层的水平侧向应力strata lateral stress，侧压系数lateral pressure coefficient，围压confinning pressure，各向压缩效应triaxial compressibility effect，有效应力effective stress，零有效应力zero effective stress:，压持效应chip hold-down effect，岩石硬度减低剂rock hardness reducer，3.2岩石的微观结构rock micro-structure，3.3岩石的宏观结构rock macro-structure 3.4岩石的不均匀性rock heterogeneity，3.5岩石的各向异性rock anisotropy3.6岩石的可钻性rock drill-ability，微观钻头可钻性试验micro-bit drill-ability test，微型钻头micro-bit，微型钻头钻速micro-bit drilling rate，微型钻头刀片齿磨损量micro-bit cutter wear，3.7岩石研磨性rock abrasive properties，3.8岩石的渗透率rock permeability，4钻前工程 prespud operation4.1定井位location determination，4.2选线route selection，4.3井场well site，4.4井场布置well site arrangement:，4.5井场道路access road at well site，4.6设备安装equipment installation，4.7圆井cellar，4.8废泥浆池waste(reserve) pit，4.9泥浆罐mud tank，4.10钻机基础rig foundation，预制基础(活动基础) pre-fabricated foundation，现浇基础(死基础) foundation grouted in situ，桩基础pile supported foundation，4.11钻机基础设计rig foundation design，4.12基础安装(摆基础)pre-fabricated foundation setting，4.13基础浇筑(打基础)foundation grouting，基坑放线foundation pit delimitation，挖基坑foundation pit excavation，填石灌浆grout for bonding rubbles placed into pit，4.14基础找平foundation levelling，4.15基础养护concret foundation curing，4.16井架derrick(mast)，塔形井架pyramid mast，自升式井架self erection mast，前开口式井架cantilever mast，A形井架A-mast，桅形井架mast，4.17井架结构参数derrick structural parameter，井架公称高度derrick nominal height，井架底尺寸derrick base size，井架上底尺寸water table size，二层台公称高度monkey board nominal height:，井架大门高度V-door height，井架大门开档尺寸V-door demensions，4.18井架构件derrick member，井架大腿derrick leg，底板(支脚板) bottom plate，横杆(横拉筋) girt，斜杆(斜拉筋) brace，联接板(节点板) connection angle-plate，操作台working platform:，指梁finger board，二层台racking platform(monkey board)，三层台auxillary racking platform，天车台crown safety platform(crown runaround)，天车台人字架gin pole，立管台standpipe board，井架绷绳derrick guy line，绷绳锚guy line anchor(dead-man)，扶梯ladder，钻台derrick floor，立根盒pipe setback(setback)，井架大门(前大门) V-door，绞车大门(后大门) draw-works window opening，挡风墙wind wall，4.19塔形井架安装pyramid derrick standing，运井架derrick members transportation:，整理井架rig spotting，安装索具string drilling line and install raising line:，吊扒杆cantilever gin-polehoisting and setting，封装井架大门V-door closing，升扒杆cantilever gin-pole raising，降扒杆cantilever gin-pole lowering，放扒杆cantilever gin-pole laying down，变幅amplitude，穿钢丝绳string up(stringing up)，对吊balance hoisting with two cantilever，起天车crown block hoisting，放天车crown block dis mounting，高空操作手erector work high above ground，第一操作手first erector，第二操作手erector，第三操作手assistant erector，4.20自升式井架安装erection of self-erection mast，组装井架mast assembling，井架支架mast bracket，起升支架mast raising，起升绳raising line，底座人字架A-frame of substructure:，井架调节装置balance-adjusting device of mast，井架缓冲器mast damper，4.21整拖井架skid-mounted derrick，4.22钻机整体拖运rig skidding，4.23校正井架derrick aligning，4.24机泵房engine-pump housing，4.25钻井队野营房drilling crew mobile camp，4.26扒杆cantilever gin-pole，单扒杆single cantilever gin-pole，悬转扒杆rotable turning and suspended cantilever gin-pole:，吊臂(臂杆) cantilever，主扒杆main pole，上撑杆upper supporting pole，下撑杆lower support pole，辅助撑杆accessory supporting pole，底部转座bottom rotary table，中部转座middle rotary table，顶部转座top rotary table，座板bottom plate，臂顶滑轮cantilever top sheave，变幅滑轮cantilever amplitude sheave，底滑轮bottom sheave，起重钢丝绳hoisting line，变幅钢丝绳amplitude line，4.27井架安装车A-frame truck:，4.28静力触探车truck-mounted static probe detector，4.29尖槟吊扳手(尖扳手)cuspate spanner，5钻头的选择和使用 bit selection and application5.1钻头选型bit selection，5.2钻头检查bit inspection，5.3钻头使用寿命bit life，5.4钻头合理起钻时间reasonable time to pull the bi，5.5钻头过度使用overuse of bit，5.6钻头正常磨损bit uniform wear，5.7钻头异常磨损bit unfavorable wear，5.8钻头过度磨损bit excessive wea，5.9牙轮钻头轴承失效bit bearing failure，5.10钻头磨损分析bit dullness analysi s，牙齿的磨损分级tooth dullness grading，轴承磨损分级bearing wear grading，钻头直径磨损bit gage wear，钻头磨损特征dull bit a ppearance，牙齿折断tooth breakage，牙齿脱落lost teeth，牙齿磨损tooth wear，牙轮掉落cone losing:，牙轮破裂cone cracking，牙轮互咬cone interference，牙轮冲蚀cone-shell erosion，牙轮旷动cone shaking，牙轮卡死cone locked，轴承密封失效bearing seal failure，钻头直径磨小bit gauge wear，喷嘴脱落nozzle losing，水眼螺纹刺坏thread puncture，水眼刺坏water course puncture，喷嘴刺坏nozzle puncture，喷嘴堵塞nozzle plugging，中心磨损严重bit center cored out，巴掌断落shirt-tail cut，巴掌断裂shirt-tail breaking，巴掌尖磨损严重shirt-tail severely worn out，钻头泥包bit balling，井底落物损坏damage from foreign material，6钻柱、钻井工具及仪表 drill string, drilling tool and instrumentation6.1钻具drilling tool，方钻杆kelly，钻杆drill pipe，铝合金钻杆aluminium drill pipe，加重钻杆(厚壁钻杆) heavy wall drill pipe，钻铤drill collar，方钻铤square drill collar，偏重钻铤eccentric-weight drill collar，螺旋钻铤spiral DC(spiral-grooved DC):，接头joint(sub)，配合接头(转换接头)cross-over sub，钻杆接头drill pipe tool joint，水龙头接头swivel tool joint，方钻杆保护接头kelly saver sub，6.2钻具组合(钻具配合)drill string assembly，6.3钻柱drill stem，6.4复合钻柱combination string，6.5下部钻具组合bottom hole assembly(BHA)，满眼钻具packed hole assembly，塔式钻具tapered drill string，钟摆钻具pendulum assembly，6.6钻柱压曲pipe helical buckling，6.7切点tangency point，6.8半波长度half wave length，6.9临界钻压critical weight on bit，6.10变节距空间螺旋弯曲曲线，6.11钻柱运动方式drill string motion pattern:，钻柱的扭转振动drill-string torsional vibration，钻柱的纵向振动drill-string longitudinal vibration:，钻柱的旋转运动drill-string rotary motion，钻柱自转drill-string revolve on its own axis，钻柱公转drill-string revolve round the bore-hole axis，钻柱的复合旋转drill-string revolves both round the bore-hole axis and on its own axis，6.12钻柱受力分析drill-string force analysis，6.13钻柱拉应力drill-string tensile stress，6.14钻柱压应力drill-string compressive stress，6.15钻柱剪应力drill-string shear stress，6.16钻柱弯曲应力drill-string bending stress，6.17钻柱外挤压力drill-string collapse pressure，6.18浮力系数法buoyancy factor method，6.19压力面积法pressure-area method，6.20浮力减轻系数buoyancy factor，6.21钻柱的工作状态drill-string working status，6.22钻柱静拉设计drill-string static tensile design，安全系数法safety factor method:，设计系数法design factor method:，拉力余量法over-pull margin method:，6.23拉力余量over-pull margin，6.24钻杆允许下深drill-pipe rated depth，6.25应力减轻槽stress relief groove，6.26低扭矩面low torque face，6.27螺纹磷化thread phosphate coating，6.28阶梯内孔结构stepped bore structure，6.29上紧扭矩make-up torque，6.30最佳上紧扭矩optimum make-up torque，6.31钻铤连接螺纹弯曲强度比值DC joint bending strength ratio，6.32钻杆表面缺陷DP surface imperfection:，6.33胶皮护箍细槽rubber protector groove，6.34大钳伤痕tong mark，6.35卡瓦伤痕slip mark，6.36地层和井内金属碎屑的切割伤痕notching by formation and junk，6.37井下三器three down-hole tools，稳定器stabilizer，减振器shock absorber，震击器jar，6.38井眼扩大器reamer，6.39井口工具rig tool，大钳(吊钳) tong，吊卡elevator，卡瓦slip，安全卡瓦safety clamps，提升短节lift sub，钻头装卸器bit breaker，旋接器spinner:，6.40指重表weight indicator，6.41自动记录仪auto-graphic meter，6.42转盘扭矩表rotary table torque indicator:，6.43多参数仪multi-parameter analyzer，6.44综合录井仪mud logging unit，7钻井工艺 drilling techniques7.1钻进(纯钻进)drilling，7.2钻进技术drilling technique，7.3钻进参数drilling parameter，钻压WOB，单位钻头直径钻压W OB per unit length bit diameter，比钻压specific WOB，悬重和钻重free hanging weight and hook load while drilling，大钩载荷hook load，转速rotary speed，流量flow rate，7.4钻进瞬时扭矩torque while drilling，7.5钻进最大扭矩maximum torque while drilling，7.6中性截面neutral cross-section，7.7零轴向应力截面zero axial stress cross-section，7.8稳定力stabilizing power，7.9开钻spud in，7.10完钻drilled，7.11送钻feed off，7.12方入和方余kelly-in and kelly-up，7.13进尺penetration footage，7.14机械钻速penetration rate，7.15行程钻速roundtrip penetration rate，7.16钻时drilling time，7.17划眼redressing，7.18倒划眼back redressing，7.19扩眼reaming(under-ream)，7.20蹩钻bit bouncing，7.21跳钻bit jumping，7.22干钻drilled dry，7.23试钻drill off，7.24停钻stop drilling，7.25顿钻drill-string free fall，7.26溜钻drill-string not well braked，7.27打倒车reverse rotation，7.28通井wiper trip，7.29放空drilling break，7.30吊打easing the bit in，7.31纠斜hole straightening，7.32钻水泥塞drill out:，7.33钻开油气层drill in，7.34缩径tight hole，7.35井径扩大hole enlargemen，7.36单根single，7.37双根double，7.38立根stand，7.39替根alternating pipe，7.40吊单根picking up single，7.41接单根making a connection，7.42起下钻round trip，7.43短起下钻short trip，7.44双吊卡起下钻trip with two elevators，7.45起钻错扣alternating breaks under trip out condition，7.46倒换钻具switching within strings，7.47活动钻具drill-string movement-reciprocation VS. rotation，7.48甩钻具break down，7.49换钻头bit changing，7.50灌钻井液fill in the hole，7.51钻头行程bit run，7.52钻头磨合running in，7.53起空车running up with empty blocks，7.54穿大绳string-up drilling-line，7.55倒大绳sliping and cut off drilling-line，7.56快绳fast-line，7.57死绳dead-line，7.58鼠洞rat hole，7.59小鼠洞mouse hol，7.60拉猫头cat-line pulling，7.61转盘卸螺纹screw out by use of rotary table power，7.62转盘绷扣initial breakout tool-joint by use of rotary table power，7.63钻具刺穿wash out，7.64蹩泵pump choking up，7.65循环钻井液circulating drilling fluid，7.66地面循环surface circulation，7.67地质循环circulating for geologic observation，7.68循环周circulation circle，7.69处理钻井液drilling fluid treatment，7.70挂辅助刹车putting on auxiliary brake，7.71司钻操作台driller's console，7.72井史well history，7.73钻井日报表daily drilling report，7.74钻井班报表tour report，7.75钻井液班报表drilling fluid tour report:，7.76钻头记录bit record，7.77钻具记录drilling string record，8喷射钻井 jet drilling8.1喷射钻井jet drilling，8.2射流jet flow，淹没非自由射流submerged non-free jet，冲击射流impact jet，气蚀射流(空化射流) cavitation jet，脉冲射流pulsed jet，磨料射流abrasive jet，射流水力参数jet hydraulic，射流喷速jet velocity，射流冲击力jet impact force，射流水功率jet hydraulic horsepower，射流的极点jet stagnation point，射流的速度分布jet velocity distribution，射流的初始段flow development region，射流的基本段fully developed flow region，射流扩散角和扩散系数jet spread angle and spread coefficient，射流等速核jet patential core，漫流cross flow，漫流速度cross-flow velocity，射流速度降低系数jet velocity attenuation coefficient，射流动压力jet dynamic pressure，射流动压力降低系数jet dynamic pressure attenuation coefficient，8.3喷射距离jet reach，8.4净化井底bottom-hole cleaning，8.5钻头水力参数bit hydraulic，钻头压降bit nozzle pressure-drop，钻头压降系数Kb bit pressure-drop factor，钻头水功率bit hydraulic horse-power，钻头比水功率bit specific hydraulic horse-power，8.6喷嘴nozzle，喷嘴流道nozzle passageways，喷嘴流量系数nozzle flow rate coefficient，等速梯形喷嘴iso-velocity gradient nozzle，流线形喷嘴streamlined nozzle，脉冲喷嘴pulsed nozzle，加长喷嘴extended nozzle，喷嘴水力特性nozzle hydraulic property，喷嘴结构nozzle configuration，喷嘴组合nozzle combination，单喷嘴single nozzl，双喷嘴two nozzle，不等径组合喷嘴unequal diameter nozzle，反喷嘴inverse nozzle，喷射角impact angle，喷嘴布置nozzle arrangement，喷嘴当量直径nozzle equivalent diameter，不等径喷嘴最佳直径比值optimum diameter ratio of unequal diameter nozzle，8.7钻井液循环系统drilling fluid circulating system，循环压耗系数circulating pressure loss coefficient，循环压耗circulating pressure loss，临界压耗critical pressure loss，环空压耗annulus pressure loss，地面管汇压耗pressure losses in surface equipment，地面管汇surface equipment，8.8钻井水力学drilling hydraulics，8.9钻井液流态drilling fluid flow pattern，平板层流flat laminar flow，塞流plug flow:，管流pipe flow，Z-value，8.11平板度判别准数flat plate level criterion，8.12喷射钻井的工作方式working regime of jet drilling，最大钻头水功率工作方式maximum bit hydraulichorse-power regime，最大射流冲击力工作方式maximum jet impact force regime，最大射流喷速工作方式maximum jet velocity regime，经济水功率工作方式economic hydraulic horse-power regime，8.13最优钻井液流量optimum flow rate of drilling fluid，8.14最优喷嘴直径optimum nozzle diameter，8.15临界井深和极限井深critical and limited well depth，8.16钻井泵的工作状态drilling pump working regime，钻井泵的最大流量工作状态(额定功率工作状态) drilling pump maximum flow rate regim，钻井泵的调节流量工作状态(允许压力工作状态) drilling pump regulated flow rate regime，钻井泵的临界工作条件drilling pump critical working condition，8.17钻井泵的额定压力drilling pump rated pressure，8.18钻井泵的额定流量(缸套的额定流量)drilling pump rated flow rate，8.19钻井泵的额定冲数drilling pump rated pumping speed，8.20钻井泵的最大输出功率maximum pump discharge horse-power，8.21钻井泵的特性曲线pump characteristics，8.22钻井泵的临界特性曲线pump critical characteristics，8.23钻井泵效率pump mechanical efficiency，8.24钻井泵水功率利用率pump hydraulic power utilization efficiency，。
钻井工程常用名词术语汉英对照表钻井工程钻井工程常用名词术语汉英对照表钻井工程常用名词术语钻井总论钻井drilling钻井方法drilling method顿钻钻井cable drilling杆式顿钻rod tool drilling绳式顿钻cable tool drilling轻便钻井portable drilling直井straight hole深井deep well超深井super deep well地热井geothermal well热采井thermal production well工程井engineering rejection well工程报废井abandoned well弃井abandoned well钻井设计well design钻井质量drilling quality岩石的物理机械性质physical-mechanical properties of rock矿物的微硬度 micro-hardness of rook肖氏岩石硬度 Shores hardness史氏岩石硬度 Shi's hardness矿物的弹性模量elastic modulus of mineral岩石的弹性模量elastic modulus of rock矿物的泊松比Poissons ratio mineral岩石的泊松比Poissons ratio rock矿物的切变模量shear modulus of mineral岩石的切变模量shear modulus of rock矿物和岩石的体积压缩模量bulk compressibility mineral and rock岩石的体积压缩系数coefficient of bulk compressibility mineral and rock 岩石的抗拉伸强度tensile strength of rock岩石的直接拉伸试验 direct tensile test of rock岩石的巴西劈裂拉伸实验Brazilian test of rock岩石的筒形抗内压胀裂试验 burst test of hollow cyling by internal pressure 岩石的常规抗压缩强度 compressive strength of rock岩石的抗剪切强度 shear strength of rock岩石的抗剪切强度试验 shear test of rock岩石的三轴强度试验 tri-axial test of rock岩石的常规三轴试验 ordinary tri-axial test of rock岩石的真三轴试验 true tri-axial test of rock脆性岩石 brittle rock塑性岩石plastic rock岩石的假塑性破坏pseudo-plastic breakage of rock岩石塑性系数coefficient of plasticity of rock岩石的脆塑性转变压力（临界压力）brittle plastic transitional pressure of rock岩石的库仑纳维尔强度准则Conlomb-Navier strength criterion of rock岩石的内磨擦角和内磨擦系数angle of interal friction and coefficient of interal friction of rock岩石的莫尔强度准则 Mohr strength criterion of rock岩石的格里菲斯脆性破坏准则 Griffith criterion of brittle failure of rock 统计强度理论statistical strength theory岩石的表面破碎surface fracture of rock岩石的疲劳破碎fatigue fracture of rock岩石的体积破碎volumetric fracture of rock岩石的单位体积破碎pecific volumetric fracture work of rock地应力in situ stress岩层的水平测向应力horizontal stress of strata测向系数coefficient of lateral pressure围压confining pressure有效应力effective stress压持效应chip hold effect岩石硬度减低剂rock hardness reducer岩石的可钻性drill ability of rock岩石的研磨性rock abrasiveness钻具drilling tool钻柱drill stem复合钻柱combination string满眼钻柱packed hole assembly踏式钻铤组合tapered drill collar string钟摆钻具pendulum assembly偏重钻铤 unbalanced drill collar钻柱弯曲buckling of drill string钻具的扭转震动twisting vibration of drill string钻杆疲劳破坏fatigue-failure of drill string上紧矩 make-up torque应力减轻槽stress-relief groove减震器vibration dampener稳定器stabilizer井眼大扩器reamer钻井液drilling fluids水基钻井液water-base drilling fluids淡水钻井液fresh-water drilling fluids低固相钻井液low solids fluids低固相不分散钻井液low solids non-dispersed polymer drilling fluids 抑制性钻井液inhibitive drilling fluids盐水钻井液salt-water drilling fluids饱和盐水钻井液saturated salt-water drilling fluids钙处理钻井液calcium treated drilling fluids钾盐钻井液potassium drilling fluids混油钻井液oil-emulsion drilling fluids生物聚合物钻井液biodegrability drilling fluids油基钻井液oil base drilling fluids反相乳化钻井液invert-emulsion drilling fluids平衡活度钻井液balanced activity drilling fluids泡沫钻井液foam drilling fluids密闭液sealing fluids完井液completion fluids封隔夜packer fluids解卡浸泡液stuck freeing spotting fluids钻井液性能properties of drilling fluids滤失filtrationAPI滤失量API filtration高温高压滤失量high temperature and high pressure filtration动滤失量dynamic filtration滤饼filter cake含砂量sand content钻井液固相含量solids content in drilling fluids 亚甲基兰实验methylene blue test石灰含量lime content estimation钻井液的酚酞碱度Pm alkalinity滤液酚酞碱度Pt alkalinity滤液甲基橙碱度Mf alkalinity造浆率yield破乳电压emulsion-breaking voltage钻井液流变性drilling fluids rheology漏斗粘度funnel viscosity触变性thixotropic behavior静切力gel strength初切力initial gel strength终切力10-minuto gel strength剪切降粘特性shear-thinning behavior钻井液受污染contamination of drilling fluids粘土侵clay contamination盐侵salt contamination盐水侵salt water contamination钙侵calcium contamination砂侵sand contamination水侵water contamination气侵gas contamination钻井液处理剂mud additives降失水剂filtrate or reduction agents增粘剂thickening agent膨润土增效剂agents of increasing bentonite降粘剂thinning agents加重剂weighting agents堵漏剂lost circulation materials水敏性页岩water-sensitive shale膨润土的预水化pre-hydrated bentonite固相控制solid control钻屑cutting砂sand泥silt胶体颗粒colloidal solids钻进drilling钻进技术drilling technology钻进技术参数drilling parameters钻压weight on bit悬重和钻重string suspending weight and drilling weight 转速rpm-revolution per minute排量rate of flow零轴向点zero axial stress point中性点neutral point开钻spud in完钻finishing drilling送钻bit feed方余和方入kelly-up and kelly-in进尺footage机械钻速penetration rate鳖钻bit bouncing跳钻bit jumping干钻drilling at circulation break打倒车reverse rotation table钻头泥包bit balling划眼redressing扩眼reamin1放空drilling break吊打easing the bit in纠斜hole straightening侧钻sidetracking单根single双根double立根stand接单根king a connection起下钻trips知起下钻short tripping活动钻具move the drill string上卸扣make up and break out换钻头change bit鼠洞rat hole小鼠洞mouse hole喷射钻井jet-bit drilling射流jet flow冲击射流impact jet flow汽蚀射流cavitation jet射流扩散角和扩散系数spread angle and spread coefficient of jet射流等速patential core of jet漫流cross flow射流喷速jet velocity射流速度降低系数decreasing coefficient of jet velocity射流动压力dynamic pressure of jet flow射流压力降低系数coefficient of jet-flow pressure drop射流冲击力jet impact force射流水功率jet hydraulic-power喷射距离jet length清洗井底bottom-hole cleaning钻头压降bit pressure-drop钻头水功率bit hydraulic horse-power喷嘴nozzle等变速喷嘴nozzle with iso-variable velocity流线形喷嘴streamline nozzle喷嘴流量系数nozzle orifico coefficient钻井液循环系统drilling fluids circulating system钻井液流态flow pattern平板层流flat plate laminar flowZ值Z-value喷射钻井的工作方式The working regime of jet drilling最大钻头水功率工作方式The regime of the maximum bit hydra-ulic horse-power 最大射流冲击力方式the regime of the maximum jet-impact force最大射流喷速工作方式The regime of the maximum jet velocity经济水功率工作方式the regime of the economic hydraulic horse-power jet bit喷射式钻头optimum rate of mud flow最优喷嘴直径optimum nozzlo diameter临界井深和极限井深critical well depth and limited well depth钻井泵的工作状态the working regime of drilling pump钻井泵的最大排工作状态（额定工作功率工作状态）the maximum flow rate regime of the drilling pump (the rated power regime of the drilling pump)钻井泵的调节排量工作状态（允许压力工作状态）the regulated flow rate regime of the drilling pump(the rated power regime of the drilling pump)携带岩屑cutting carrying岩屑运移比cutting transport ratio环空岩屑浓度solid concentration in annular space钻井泵效率rate of utilized power of the drilling pump钻井泵水功济利用率rate of utilized hydraulic power of the drilling pump 优化钻井技术optimum drilling technology控制井control well钻井可控参数controllable drilling variables钻井不可控参数non controllable drilling variables钻井目标函数（钻井泛函）objective function of drilling procedure钻进过程的数学模型mathematical model for drilling procedure钻速方程equation for drilling rate二元钻速方程drilling rate equation in two variables多元钻速方程multi-variable drilling rate equation最大允许钻压maximum allowable weight on bit最优钻压optimum weight on bit钻速系数factor of penetration rate地层研磨性系数factor of formation abrasiveness牙齿磨损系数tooth wear coefficient轴承工作系数working coefficient of bearing五点法钻速试验“five spot” d rill-off test井下动力钻井hole bottom power drilling涡轮钻井turbo-drilling涡轮钻具turbo-drill电动钻具electric drill螺杆钻具positive displacement motor涡轮工作特性characteristics of turbine涡轮的水力载荷hydraulic load on turbo-drill涡轮钻具井底工作特性hole-bottom working characteristics of turbo-drill 涡轮钻具最优工作区optimized working zone of turbo-drill涡轮钻具合理转速optimum revolution of turbo-drill涡轮钻具最优排量optimum capacity of turbo-drill涡轮不稳定工作区unstable working range turbo-drill有效钻压effective bit-weight涡轮钻具井底功率传递系数transfer coefficient of bottom hole power of turbo-drill涡轮钻具特性系数characteristic coefficient of turbo-drill涡轮的水力效率hydraulic efficiency of turbo-drill涡轮钻具合理钻进深度optimum drill depth of turbo-drill涡轮-泵组联合特性combined characteristics of turbo-drill-pump涡轮钻具轴向间隙的调节axial clearance regulation of turbo-drill钻具滤清器drill pipe filter启动阀starter gate valve低速大扭矩涡轮钻具love-speed high-torque turbo-drill复式涡轮钻具compound turbo-drill定向井directional well定向要素directional elements井斜角inclination方位角azimuth井斜变化率rate of inclination change方位变化率rate of azimuth change井眼曲率hole curvature垂深和测深vertical depth and measured水平投影长度hole deviation水平位移displacement or closure distance多底井multi-bore well水平井horizontal well丛式井cluster well or multiple wells救除井relief well双筒井dual wells套管开窗starting window on casing造斜 deflecting or building angle增斜increasing hole angle or build-up hole angle降斜decreasing hole angle or build-off hole angle稳斜 maintain angle井身垂直投影图vertical projection of borehole井身水平投影图 horizontal projection of borehole 正切法tangential method平衡正切法balanced tangential method平均角法average angle method曲率半径法radius of curvature method圆弧法arc method最小曲率法minimum curvature method圆柱螺线法cylinder helix method悬链线轨迹·catenary shape profile控制圆柱control cylinder造斜工具deflecting tool槽式变向器whip-stock短涡轮short turbo-drill钻铤造斜短节short bent collar涡轮偏心短节turbo-eccentric sub复式弯涡轮bent multi-turbo-drill水力斜接头hydraulic bent sub Dyna-flex瓦片变向器rebel tool 造斜工具面tool face 造斜率rate of over-all angle change井眼方位漂移walk of hole装置角tool of rotation工具面角tool face azimuth动力钻具反扭角reactive torque定向方位角tool face bearing or tool face setting 磁偏角magnetic declination随钻测量measurement while drill(MWD)单点测斜仪single shot instrument多点测斜仪multi-shot instrument陀螺测斜仪gyroscopic instrument定向orientation定向下钻orientation while going in hole磁力定向法magnetic orientation method斜口管鞋定向法mule-shoe orientation method取心coring岩心core岩心收获率recovery of core取心方法coring method局部反循环取心coring with local inverse circulation 长筒取心core drilling with long core barrel密闭取心sealing core drilling保压取心core drilling with keeping formation pressure 定向取心orientation coring绳索取心wire line coring取心工具coring tools岩心筒core barrel单筒式岩心筒single type core barrel双筒式岩心筒core barrel of double tube swivel type内岩心筒inside core barrel外岩心筒outside core barrel喷射式岩心筒core barrel of jet type取心钻头coring bit牙轮取心钻头coring cone bit金钢石取心钻头diamond coring bit硬质合金取心钻头hard metal coring bit涡轮取心钻头turbo-core bit涡轮取心钻具turbo-core drill岩心爪core gripper卡瓦式岩心爪core gripper with slip卡簧式岩心爪core gripper with slip-spring板簧式岩心爪卡core gripper with slip-spider箍式岩心爪core gripper with slip-collar割取岩心core breaking机械加压割心法core breaking by mechanical loading投球割心core breaking by hydraulic pressure投砂割心core breaking by pumping down顶岩心core extracting各种压力概念concept of pressure静液压力hydrostatic pressure钻井液压力drilling fluid column pressure孔隙压力pore pressure (formation pressure)上覆岩层压力overburden pressure颗粒压力grain to grain pressure压力梯度pressure gradient压力监控pressure detection and control异常压力及其形成abnormal pressure and it’s formation压力异常abnormal pressure压实作用compaction欠压实imcompaction不渗透围栅·permeabillity barrier快速沉积rapid deposition构造型异常高压structural abnormal pressure地层压力检测方法method of formation pressure detection地震资料法seismic data method机械钻速法penetration rate methodd指数法d-exponent method dc指数法 dc-exponent method标准化钻速法normalized penetration rate页岩密度法shale density溢流观测法take a kick天然气录井检测法gas logging氯化物检测法chloride log钻井液录井法drilling fluid log返出钻井液温度检测法flow-line temperature化石资料法paleo-information地球物理检测法wire-line logs中途测试drill-stem testing完井测试well completing test综合录井仪computerlized apply drilling technology地层破裂压力formation fracture pressure地层破裂压力预报方法formation fracture pressure prediction 漏失试验法leak-off test胡伯特-威利斯法 Hubbert and Willis approach马修斯-凯利法method of Matthews and Kelly伊顿法method of Eaton安德森法Anderson’s method艾克斯劳格法Exlog method黄荣樽法Huang’s method地层井眼系统的压力平衡balance of formation-borehole system 地层压力当量钻井液密度equivalent drilling fluid density钻井液当量循环密度equivalent circulating density附加压力当量钻井液密度additional pressure equivalent density 当量深度equivalent depth钻柱排代量drilling fluid displacement波动压力（激动压力）surge pressure抽汲压力swabbing pressure气体上窜gas channeling天然气偏差因子the coefficient of gas compressibility溢流overflow井涌kick井喷well blowout地下井喷underground blowout井喷失控out of control for blowout循环池液体增量pit gain压力过渡带pressure transition zone压井killing well关井closing well硬关井hard closing软关井soft closing压井方法killing well method工程师法（等待加重量法）engineer’s method司钻法（二次循环法）driller’s method边加重边循环法concurrent method空井压井empty well control置换式压井法（顶部压井法）displacement method反循环inverse circulating循环周circulating circle节流循环circulating with choke防喷设备和工具blowout prevention tools and equipments防溢管·bellnipple钻井液流量计drilling fluid flowing indicator泵冲数计pump-stroke counter钻井液液面指示器pit-volume indicator真空除气器·vacum degasser硫化氢监测仪H2s detector井控模拟装置well control simulator井喷失控的处理well blowout control抢装井口installing wellhead扣装法抢装井口buckling-up-installing wellhead翻转法抢装井口turning-up-installing wellhead整体吊装法抢装井口whole hanging method for installing wellhead 带帽子压井法·hatting kill well method下封隔器压井killing well with packer method换井口套管casing replacing灭火extinguishing喷射水流灭火法jet fire extinguishing method爆炸灭火法explosion method灭火剂extinguisher固井well cementing套管程序casing program导管conductor表层套管surface casing技术套管intermediate casing strings生产套管production casing套管柱casing string套管柱下部结构casing accessories引鞋guiding shoe套管鞋casing shoe套管扶正器centralizer泥饼刷wall scratcher浮籀float collar套管承托环cement baffle collar旋流短节vortex sub浮鞋cementing float collar水泥伞cementing basket注水泥胶塞cementing plugs通径规drift diameter gauge套管的外载荷outside casing load套管内压力burst套管外挤压力collapse pressure套管轴向力axial load套管强度casing strength套管抗挤强度collapse resistance套管抗拉强度tensile resistance套管抗内压强度burst resistance下套管running casing活动套管moving casing预应力preceding stress人工井底artificial bottom of a well磁性定位短节magnetic locator sub固井工具与设备tools and equipments for running casing and cementing 套管吊钳casing tong套管吊卡casing elevator卡盘casing spider联顶节top connecting collar水泥头connect head水泥车connecting truck井口装置wellhead equipment注水泥?connect油井水泥oil well connecting低密度水泥light weight connect膨润土水泥·bentonite connect速凝水泥accelerated cement膨胀水泥expansion cement纤维质水泥fiber cement树脂水泥（浆）resin cement油基水泥（浆）diesel-oil cement橡胶水泥（浆）latex cement酸溶性水泥acid dissoluble cement石膏水泥混合物·gypsam cement火山灰水泥·pozzolan cement抗盐水泥salt-resisting cement双凝水泥浆separable setting cement slurry冷井水泥和热井水泥ordinary and hot cementAPI水泥分级API cement classification水泥浆性能及其调节cement properties and adjustments of them稠度仪consist-meter水泥浆流动性mobility of slurry水泥浆密度slurry density水泥浆滤失量slurry filtration出口温度井底温度和循环温度flow-line temperature bottom temperature and circulation temperature水泥浆失重losing weight slurry水泥石强度cement strength水泥石渗透性permeability of set cement水泥石的射孔性perforating quality水泥浆外加剂cement additive速凝剂accelerator缓凝剂retardant减阻剂friction reducer降密度剂light weight additive降失水量filtrate reducer水泥浆加重剂heavy weight additive隔离液spacer fluid前置液ahead fluid尾随液tail fluid注水泥方法cementing methods常规注水泥法typical primary cementing双级注水泥法two stage cementing插入注水泥法inner pipe cementing多管注水泥法multi-plezone completion cementing打水泥塞cementing plug平衡法打水泥塞balance method for cementing plug倾筒法打水泥塞dump bailer method挤水泥squeeze method井口挤水泥法braden head squeeze method封隔器挤水泥法squeeze packer method高压挤水泥法high-pressure squeeze method低压挤水泥法low-pressure squeeze method尾管固井drilling liner cementing尾管悬挂器drilling liner hanger窜槽cement channeling完井方法completion methods裸眼完井法open hole completion先期裸眼完井法initial open hole completion后期裸眼完井法final open hole completion射孔完井法perforation completion单管射孔完井法single pipe perforation completion多管射孔完井法multiple pipe perforation completion无油管完井法·tubingless completion永久完井法permanent completion无封隔器单层永久完井法single pipe permanent completion without packer 单封隔器永久完井法permanent completion with single packer封隔器射孔完井法permanent completion with packer负压射孔perforating with negative pressure过油管射孔perforating through tubing贯眼完成法perforated pipe completion衬管完井法liner perforation completion砾石充填完井法gravel packer completion深井完井法deep hole completion高含硫气井完井法high H2s gas well completion地层损害程度formation damage degree地层损害带formation damage zone水动力学程度不完善井hydrodynamic degree incompleteness well水动力学性质不完善井油井hydrodynamic property incompletion well完善系数well completeness factor损害比damage ratio趋肤效应shin effect开采比production ratio损害系数damage factor完井系数completion factor钻井设备drilling equipment设备安装rig up钻前工作preliminary work for spudding井场布置layout平井场levelling圆井cellar基础ground foundation base活动基墩removable foundation井架安装derrick installation扒杆gin pole井架安装绞车winch穿钢丝绳string up死绳固定器dead line anchor设备校正alignment井口找中center for well整体搬迁skidding the rig成组安装package installation泥浆管汇mud pipeline猫头绳cat-line高悬猫头绳drill rope大钳尾绳safety line大门绷绳front guy(lines)井架绷绳derrick guy接链器chain spanner钻井数据系统drilling data system钻井数据采集装置drilling data acquisition钻井数据实时处理装置drilling data processing钻井数据库drilling data base钻井信息drilling information钻井参数传感装置drilling parameter sensing unit指重表传感器weight sensor进尺传感器drilling footage sensor转盘扭矩传感器rotary table torque sensor转盘转速传感器R.P.M sensor for rotary table大钳扭矩传感器torque sensor for tong泵速传感器pump rate sensor钻井液密度传感器drilling fluid weight sensor钻井液液面传感器mud pit level sensor钻井液流动传感器drilling fluid flow sensor钻井液温度传感器drilling fluid temperature sensor钻井液电导传感器drilling fluid conductivity sensor 录井logging钻井液录井drilling fluid logging岩样录井·lithologic logging气测录井gas-logging钻速录井penetration rata logging综合录井compound logging巡回检测cyclic detection泵压表pressure gage钻具事故drilling pipe and tools accident顿钻drill string free fall溜钻drill string not well braked断钻具drilling pipe breaking落鱼fish落物junks打捞作业fishing打捞筒overshot打捞杯fishing cup反循环打捞篮junk basket with reverse circulation 壁钩wall hook铅印模lead stamp一把抓catchall铣鞋mill shoe钻杆外割刀external cutter活动肘节knuckle倒扣捞矛left hand fishing spear弯钻杆bend drill pipe尖钻头tip bit卡钻drill pipe sticking砂桥卡钻sand bridging键槽卡钻key seating压差卡钻differential sticking地层膨胀卡钻formation swelling sticking地层坍塌卡钻formation collapse sticking钻头泥包卡钻balling-up sticking点sticking point解卡工具releasing tools震击器bumper下击器bumper jar上击器top jar地面下击器surface bumper jar千斤顶jack爆炸松扣break-outing pack of dynamite测卡仪sticking-point-instrument解卡方法releasing method震击解卡法releasing stuck tamping油浴解卡法releasing stuck by pump oil into the annuls 酸浴解卡法releasing stuck by acidding割铣解卡法releasing stuck by cutting套铣解卡法milling and breakout爆炸解卡法explosion releasing method跳槽·netch jumping粘扣thread gluing滑扣thread slipping脱扣thread off错扣thread alternating对扣make-up造扣thread making顶天车crashing into the crown磨蚀钻井abrasive cutting drill弹丸钻井bullet-shot drill电火花钻井electric spark drill超声波钻井supersonic wave drill火焰钻井flame-jet drill电加热钻井electric heating drill原子能钻井atomic energy drill电弧钻井electric arc drill等离子钻井plasma jet drill电子束钻井electron-beam drill激光钻井laser drill化学腐蚀钻井chemical erosion drill钻井技术经济指标tech-economic indication of drilling 开钻井口数spudding well number完钻井口数drilled well number完成井口数completed well number钻井进尺drilling footage取心进尺coring footage井身质量合格率well bore quality qualified ratio油层固井合格率oil reservoir well quality qualified ratio钻井工程报废drilling engineering abandonment报废井段abandoned range报废进尺abandoned footage钻机利用率rate rig utilization钻机台月rigs per unity month建井周期台月construction cycle per unity month纯钻井时间reciprocating time钻机月速度monthly drilling rate周期钻速periodic drilling rate纯钻速rate of penetration行程钻速drilling rate of a trip建井周期construction cycle完成井平均建井周期average construction of completed well完成井平均井深average well depth of completed well完成井平均进尺average bit drilling footage of completed well 钻井时效分析drilling prescription analysis进尺工作时间footage working time固井工作时间cementing working time辅助工作时间service working time事故损失时间accident losing time修理时间repairing time组织停工损失时间management down time loss处理复杂情况时间problem handling time生产时间率production per cent age纯钻进时间率reciprocating time ratio每钻机台月耗柴油量diesel consumption per rig-month每钻机台月耗机油量oil consumption per rig-month钻井工程成本cost of drilling engineering。
钻井设备及工具中文名称English name中文名称English name 储能器accumulator刮管器casing scraper循环池active tank套管鞋casing shoe（刹把）调节螺栓adjusting bole套管卡瓦casing slip进气管admission pipe套管打捞矛casing spear搅拌器agitator套管四通casing spool空气包air chamber套管大钳casing tong气管线air line锚头绳cat line气动绞车air-operated hoist锚头绳爪cat line grip交流电驱动alternating current drive锚头轴cat shaft环形BOP annular BOP锚头cat-head消音器ato-muffler井口甲板cellar deck水泥cement球阀ball valve水泥伞cement basket井口喇叭管bell nipple水泥塞cement plug老虎钳bench vise水泥阻流环cement retainer钻头bit固井质量检查cementing bond log钻头装卸器bit breaker水泥头cementing head钻头规bit gauge固井管线cementing line盲板防喷器blind ram preventer固井泵cenmenting pump剪切闸板防喷器blind shear ram preventer链chain防喷器blow-out preventer链钳chain pipe tong螺栓bolt链钳chain tong防喷器控制盘BOP control pannel房间，寝室chamber防喷器平台BOP deck阀箱，闸室chamber gate底塞bottom piug灌注泵charge pump母扣box止回阀、回压凡尔check valve刹把brake level(brake handle)节流阀、阻流器choke刹带brake line (brake staple)阻流管线choke line桥塞bridge plug节流阀位置指示器choke position indicator 梯形扣buttress节流阀choke valve蝶阀butterfly valve阻流管汇choke-line manifold旁通by-pass离合器clutch旁通塞by-pass plug导管conductor牙轮cone卡钳callipers牙轮打捞器cone fisher套管打捞筒casing bowl牙轮卡死cone lock套管接箍casing coupling冷却水泵cooling-water pump套管隔刀casing cutter取心筒鞋core barrel shoe套管吊卡casing elevator取心爪core basket套管悬挂器casing hanger取心钻头core bit套管头casing head岩心爪core catcher套管平台casing monkey board岩心爪外套core catecher case岩心烘箱core drying oven外部割刀external cutter变换接头crossover joint(x/o)吊耳、吊环eye plate天车crown block绳套、接环eye splice天车梁crown block beam灌泥浆管线fill up line死绳dead line失水测定仪filtration test apparatus死绳固定器膜片dead line diaphragm指梁finger board死绳固定器dead line anchor打捞钩fishing hook除气器degasser打捞头fishing head井架derrick打捞震击器fishing jars除砂（泥）器desander(desilter)打捞颈fishing neck直流电驱动direct current drive打捞公锥fishing nipple排出管线discharge line打捞作业sishing operation排出阀discharge valve打捞母锥fishing socket双闸板防喷器double ram type preventer打捞矛fishing spear入井工具down hole tool打捞管柱fishing string绞车draw works打捞公锥fishing tap(taper)绞车电机drawworks motor打捞工具fishing tool通径规drift mandrel法兰flange钻铤drill collar扁锉flat(round,square)file钻铤卡瓦drill collar slip扁嘴钳flat bit tongs钻杆drill pipe平地铣鞋flat bottom mill钻杆卡瓦drill pipe slip绕性接头flexible joint钻杆刮泥器drill pipe wiper浮鞋float shoe钻柱drill string浮阀float valve司钻控制台driller's console浮箍floating collar司钻监视器driller's monitor四通阀four-way valve钻井大绳drilling line(workline)卡点测定仪free point indicator钻杆防喷器drilling stem valve贯眼钻杆接头full hole joint驱动轴drive shaft漏斗粘度计funnel viscometer从动轴driven shaft传动链条driving chain储气筒gas holdre(tank)滚筒drum大门gate滚筒容量drum capacity闸门阀gate valve滚筒离合器drum clutch鹅颈管goose neck pipe滚筒高速（低速）drum hight air clutch空气离合器drum low air clutch锤子hammer分级箍DV collar加重钻杆heavey weight drill pipe厚壁钻杆heavy wall drill pipe涡磁刹车eddy current brake高压管线hagh pressure line吊卡elevator开眼器hole opener吊卡耳环elevator link大钩hook吊卡-卡盘elevator-spider大钩弹簧hook spring应急牙嵌离合器emergency jaw clutch水龙带hose（刹带的）平衡杠equalizing yoke卸扣液缸hydraulic break-out cylinder 外卡钳external cutter液压锚头hydraulic catwork液压泵hydraulic pump上扣猫头make out catchead液压油箱hydraulic reserviur手摇钻manual drill液压大钳hydraulic tibg手动阀manual valve液动阀hydraulic valve转盘大补心master bushing液动试压泵hydraulic (press)test pump铣鞋millingshoe液压绞车hydraulic-powered winch铣具milling tool混合漏斗mixing hopper惯性inertia混合泵mixing pump惯性刹车inertia brake猴台monkey board入口inlet电机，马达motor内岩心筒inner core barrel小鼠洞mouse hole中间套管intermediate casing泥浆比重计mud balance钻刚内防喷器intermnal blowout preventer泥浆清洁器mud cleaner内卡钳internal callipers泥浆槽mud ditch内外加厚internal external upset挡泥板mud guard内平钻杆接头internal flush joint泥浆枪 mud gun泥浆泵mud pump震击器jar泥浆泵安全阀mud relieg valve牙嵌离合器jaw cluth泥浆返出管线mud rutern line接头，单根joint泥浆池mut pit笼式打捞篮junk basket打捞爪junk catcher钉子nail打捞杯junk sub近钻头扶正器near-bit stabilizer针形阀needle valve方补心kelly bushing扳手加长套筒nigger-head方钻杆考克kelly cock镊子nipper方保接头kelly pretective sub非磁钻铤non-magnetic drilling collar 方钻杆旋转短节kelly spinner常闭阀normal close valve键槽破坏器key seat reamer常开阀normal open valve压井管线kill line水眼nozzle弯管knee pipe螺帽nut带帽螺栓nut bolt梯子laddre自动螺母扳手nut spinner水平仪level提伸短节listing plug油位oil level滑车装绳数lifting sub油位检查丝堵oil level check plug缸套line reeving油柜oil tank尾管liner油尺oil-level dipstick锁紧螺栓liner开口扳手open-ended spanner锁紧法兰lock bolt外岩心筒outer core barrel低压管线locking flange出口outlet润滑油泵low pressure line加油孔lube oil pump油漆刷paint brush磁力打捞工具lubrication hole领眼钻头pilot bit公扣pin卸扣猫头magnetic fishing tool销子pin钳子pincers 螺钉screw撬杠pinch bar 螺丝刀screw driver 活塞piston 无缝钢管seamless pipe 活塞皮碗piston up 立根盒容量setback capacity 活塞杆piston rod 沉砂池setting pit 手钳子pliers 轴shaft旋塞阀plug valve 振动筛shalc shaker 气动工具pneumatic tool 减震器shock absorber 硅酸盐水泥portland cement 倒开门吊卡side door elevator 动力卡瓦power slip单根吊卡single join elevator动力供应设备power supply unit 单闸阀防喷器single ran type preventer 动力大钳power tong 计算尺slide rule 动力扳手power wrench管钳slide tongs 缓冲罐pressure snubbling tank 吊索sling 生产层套管production casing 卡瓦slip滑轮pulley卡瓦补心slip bushing 反循环接头pump-out reversing sub 卡瓦牙板slip dog 短钻杆pup pipe joint 卡瓦槽slip groove 卡瓦牙slip insert 快速联结quikck connection卡瓦打捞筒slip socket(卡瓦)锥形座slip socket bowl （井架大门处）坡板ramp 套筒扳手socket 大鼠洞rat hole卡盘spider正规钻杆接头regular tool joint 螺旋钻铤spiral drill collar 调节阀regulator valve 钢丝绳打捞钩spud spear 放压管线relief line开眼钻头spudding bit承托环retaining ring (support ring)插入式注水泥stab-in cementing 反循环阀reverse circulation valve 对扣台（下套管用）stabbing board 反循环打捞篮reverse circulation junk basket扶正器stabilizer 反循环孔reverse circulation port 不锈钢stainless steel 导档齿轮reverse gear 立管stand pipe 倒扣工具reversing tool 插人头stinger钢圈ring gasket （内管）注水泥管柱stinger strings 梅花扳手ring spanner 双端螺栓stud 铆钉river双头螺栓stud bolt 转盘rotary table盘根盒stuffing box 转盘电机rotary table motor接头sub转盘风机rotary table motor blower 吸入管线suctionline 吸入阀suction valve 安全卡瓦safety clamp(slips)表层套管surface casing 安全接头safety jont 水龙头swivel 安全限位档块safety stop 安全开关safety switch 卷尺tape measure 安全带safty -strap(belt)三通tee 捞砂滚筒sand reel丝扣thread筛布screen cloth丝扣油thread dope护丝thread protector先行水ahead water三牙轮钻头three-cone bit环空流速annular velocity大钳tong表观黏度apparent viscosity大钳平衡器tong bucket倒扣back off大钳牙板tong dies回压back pressure钳头tong head打好背钳back up attachment大钳刻痕tong mark泥包ball up大钳搭绞部位tong space压舱水ballast water工具接头tool joint尾水behind water工具钢tool steel宾汉模型bingham model顶（底）塞top(bottom) plug钻头成本bit cost水泥面top of the cement钻头直径bit diameterTOTCO承托环TOTCO ring baffle plate钻头进尺bit footage游动滑车traveling block钻头IADC编码bit IADC code泥浆计量罐trip-tank钻头寿命bit lift两通阀two way valve钻头位置bit position钻头系列号bit series number井架大门v-door钻头齿bit teeth阀门valve钻头时间bit time阀，凡尔valve钻头类型bit type凡尔体valve body钻头磨损bit wear阀盖，阀帽valve bonnet吹扫作业blow job凡尔座balve cup(seat)扫线用管线blow line阀面valve face吹压压力blowing pressure阀杆valve lever井喷blowout阀密封valve seal防喷bolwout control起阀座器valve seat grab防喷设备blowout control equipment 阀弹簧valve spring装卸防喷器BOP handling灵敏指针vernier沉砂bottom fill虎钳vice(=vise)井底压力bottom-hole pressure双母接头box-box connection壁钩wall hook套管程序casing program冲管wash pipe套管尺寸casing size耐磨补心wear bushing阳离子表面活性剂cationic surface active agent 井口装置well-head equipment烧碱caustic soda造斜器whip stock水泥胶结cement bond翼状扶正器wing stabilizer水泥串槽cement channeling 20"“ L”型接头type "l" connector固井失败cement failure水泥冲洗cement flush水泥浆cement slurry固井配方cementing formulation循环circulation粘土泥浆clay base mud控制钻进control drilling岩心取样coring sample腐蚀corrosion临界速度critical velocity气显示gas showing天车防碰装置crown block protector硬地层hard formation天车防碰装置crown block saver井眼尺寸hole size割大绳cut off drilling line井眼纠斜hole straightening危险品danderous objects大钩负荷hook load除垢剂degasser efficiency大钩位置hook position井斜测量deviation survey初切力initial gel-strength压差卡钻differential pressure sticking内管注水泥inner string cementing定向钻井directional drilling表面活性剂interface level indicator定向井directional well方入kelly down狗腿dog leg方入深度kelly dowm depth狗腿率dog leg ratio方入kelly in停工时间down time方余kelly up通径drifting键槽卡钻key-seating sticking钻具组合drilling assembly井涌kick钻进突变drilling break控制井涌kick control钻进承包商drilling contractor压井kill well钻井成本drilling cost甩钻杆lay down the drill pipe钻进时间drilling hours漏失实验leak-offtest钻井作业drilling operation左旋“J”型槽left-hand J-slot钻井程序drilling preogram迟到时间log time钻井报表drilling report低固相泥浆low solid mud钻井日报drilling daily report最小速度maximum pressure钻井水drilling water平均海平面maximum speed钝钻头分级dull bit grading平均潮面mean sea level戴纳钻具dyna-drill泥浆添加剂mean tide level乳化剂emulsifying agent泥浆柱mud additive刺坏erode out泥浆柱mud column评估井evaluation well调节泥浆mud conditioning初探井exploratory well泥浆处理材料mud conditioning materials 疲劳极限fatigue limit泥线mud line自动灌浆浮鞋fill-up float shoe泥浆录井mud logging泥饼filter cake泥浆量mud volume降失水剂filtration-reducing agent不漏no leak絮凝作用flocculation无返出no return流压flowing pressure水眼效率nozzle efficiency失水fluid loss水眼尺寸nozzle size地层formation离开井底off-bottom地层测试formation test海上offshore地层水formation wter漏油oil leak淡水fresh water油层压力oil reservoir pressure功能测验function test耐油橡胶oil resistant gom气含量gas content油封oil seal气侵gas cut油页岩oil shale泥浆中的气gas in mud油基泥浆oil-base mud气层gas reservoir 接触井底on bottom 裸眼open hole 开钻spud in 作业者operator 开钻泥浆spud mud上提，遇卡overpull 挤水泥squeeze cement 上扣过紧overtonging 分级注水泥squeeze cementing 钟摆钻具组合pendulum bottom hole assembly待命stand-by 机械钻速penetration rate 待命费stand-by rate 塑性黏度plastic viscosity 启动（泵）start ip(pump)塑料plastics静压static pressure 水泥回堵plugging back卡钻sticking管内压降pressure loss in pipe 卡点sticking point 压力试验pressure test 泵冲stoke泵入水泥塞pump down plug 抽吸压力swab pressure 泵效pump efficiency 抽吸swabbing 泵压pump pressure 转盘高度table height 泵速pump speed 转盘扭矩table torque 泵冲pump stroke 试纸test paper 额定流量rated flow 绸化时间thicking time 划眼reaming 错扣thread alternating 记录record造扣thread making 记录纸recording paper 脱扣thread off松开捞矛releasing spear 滑扣thread slipping 缓凝剂retarder缩径井眼tight hole 反循环reverse circulation 大钳扭矩tong torque 钻台rig floor 起下钻trip转盘转速fotary speed 起下钻时间tripping time 下套管run casing 事故troubles运转时间running time 垂深vertical depth 下入工具running tool 增稠剂viscosifier砂桥sand bridge侯凝wait on cementing 饱和盐水泥降saturated salt-water mud 壁厚wall thickness 晕船sea sick开泵循环下放wash dowm 海水泥浆seawater mud 冲刷井段wash out section 坐卡瓦setting slip 水击water hammer 浅层气shallow gas 钻压weight on bit泥质砂岩shaly sand 加重材料weighting materials 短起下short trip 井口流压well head flow pressure 关井shut-in井位well location 关井套压shut-in casing pressure 通井wiper trip关井钻杆压力shut-in drill pipe pressure 作业指令working instruction 请病假sick leave 工作压力working pressure侧钻side tracking 倒大绳slip drilling line 坍塌sloughing ,caving 苏打soda软地层soft formation固相含量solid content 锚anchor 救生圈life buoy 抛锚船anchor boat 救生衣life jacket 风速表anemometer 救生艇lifeboat 重晶石barite 照明lighting气压计barometer 水位报警器liquid level alarm 般土bentonite 定位浮标locating buoy 锅炉boiler 人孔、检修孔manhole爬杆boom 人孔盖manhole cover 防喷演习BOP drill指示灯、标志灯marker lamp手提式CO2灭火器CO2 hand-portable fire-extingusisher隔膜泵membrane pump 空压机compressor 锚泊系统mooring system 冷凝器condenser 马达油motor oil吊车crane 拖航灯navigation lights 甲板deck空载、空车no load柴油机diesel engine 障碍灯obstruction light 吃水线draft line超载overload 电动机electrical motor 泥浆池测定演习pit drill排烟管engine exhaust line 可移动式1211灭火器portable 1211 extinguisher柴油engine oil手提式干粉灭火器portable dry powder fire extinguisher逃生呼吸器escape bresthing apparatus 生活水（淡水）portable water (fresh water)传真facsimile压载水preload water 消防报警系统fire alarm system 压载preloading 消防演习fire drill 通风设备rrentilation 太平门fire escape 软（绳）梯rope laddre 消防斧fire hatchet 接线盒rosette 消防管线fire line 安全网safety net 消防面罩fire mask 卫生水管线sanitary line消防服fireman's suit海水淡化装置swawater distillation unit 急救设备first-aid equipment 海水管线seawater line 急救箱first-aid kit 分离器seperator 泡沫灭火系统foam fire extinguishing sysem值班船stand-by boat 燃油（柴油）fuel(diesel oil)担架stretcher防毒面具gas mask 潜水泵submerged pump 发电机generator 救生服survival suit 砂轮机grinder电话telephone 硫化氢气体检测系统H2S gas detection system 电传打字机teletype 热交换器heat exchanger 电传打字电报telex 加热盘管heating coil 试运转、试车test run直升机平台helicopter port 温度计thermometer 可膨胀式救生阀inflatable liferaft 可控硅thyristor 升降室jack house 计时器、秒表timer 升船jacking气焊torch升降系统jacking system拖缆towing line信号、信号灯lantern收发报机transceiver 车床lathe变压器transformer 桩腿leg打字机typewriter 卸载unload可变载荷variable load排气孔vent hole电焊条welding electrode绞盘、绞机windlass工作救生衣work life jacket气压表air pressure gauge流量警报器flow alarm流量指示器flowing indicator流量计flowing meter泥浆流量计mud flow meter泥浆体积指示器mud volume indicator油压表oil pressure guage泥浆液位计pit level meter位置指示器position indicator压力表pressure gauge泵冲数计数器pump stroke counter泵冲数指示器pump stroke indicator泵冲数传感器pump stoke sensor转盘转速表rotary speed indicator转盘扭矩表rotary torque indicator灵敏度sensitivity指重表weight indicator。
钻井常用术语英汉对照汉语英语汉语英语井位Contract Area动塑比PV/YP井号Well Name初终切Gel 0/10承包商Contractor失水Water Loss设计井深T.D.pH值pH天气情况Weather固相含量Solids日期Date成分Comments钻井日报Daily Drilling Report泥浆泵参数Mud Pump Output and Hydraulics+A53钻机编号Rig No泵号Pump #上报时间Activity @ Report Time类型Model现井深Depth @ noon冲数Stroke起始井深Previous Depth缸套直径Liner日进尺Meterage/Footage套管及固井Casing and Cementing开钻天数Days Since Spud套管尺寸Casing Size时间情况Time Distribution总数Total JTS自From总长Length到To总重Weight小时Hours钢级Grade工作内容Description of Operations扣型Thread钻井监督Representative范围Range安全提示Safety meeting下深Shoe @明日计划forward plan其它信息Other information钻头报告Bit Record测斜情况Surveys钻头号Bit No.井深Depth尺寸Bit Size井斜角Angle厂家MFG.悬重String Weight类型Type井场钻具数量Tubulars on Location序列号Ser. No.方位Azim水眼Jets测深TVD进尺Meters井斜Dev钻头时间Bit Hrs.取心井段coring depth机械钻速MPH心长core longth地层Drillig收获率recovery钻压W.O.B下深102.39米on bottom at 102.39m转速RPM钻井队drilling team封井器BOP固井公司cementing泥浆报告Mud Report录井公司mud logging采样时间Time电测队wireline logging密度 (g/cm3)Den (g/cm3)胜利定向井directional engineer粘度 (s)Vis (s)晴Sunny & warm开钻准备prepare to spud.钻进drilling循环circulate circulating短起下3柱make a 3 stand trip起钻POOH.下套管run casing .landed CSG固井do cement job .侯凝waiting on cement.封井器试压test BOP.检修repair the instrument等电测waiting for the wireline logging team.电测wireline logging.通井run in hole.cir.and pull out of the hole.二开准备prepare to the second spud.下钻make in hole.钻水泥塞drill cement plug.测斜make a survey.取心钻进coring割心cut core.出心take out the core划眼ream from固井后测井wireline logging三开准备prepare the third spud.检修maintenance rig低压钻进drilling with low WOB修泵repair pump发电机generatorA53。
英文钻井日志常用缩写词汇英文钻井日志常用缩写词汇(按照钻井施工顺序排列)DC ----- drill collar 钻铤DP ----- drill pipe 钻杆TD ----- true depth 垂直井深TD ----- total depth 总进尺，总深度USG ------ u nited statesgallon 美制加仑Hrs ---- hours 小时Drlg ----- d rilling 钻进，钻井Circ --- circulating 循环Hi. Vis. -h igh viscosity 高粘度CSG ---- casing 套管POOH ----- p ull out of hole 起钻R/U ---- rig up 安装SXS ---- sacks 袋子WOC ---- wait on cement 候凝MW ----- mud weight 泥浆比重N/U ---- nipple up 安装P/U ---- pick up 上提，提起TIH ---- trip in hole 下钻Cmt ---- cement 水泥DCS ---- drill collar stem 钻铤柱ISF ---- induction-spherically focused log 感应-球形聚焦测井LSS ---- long-spacesonic (log) 长源距声波测井GR ----- gamma ray log 自然伽马测井LCST --- lower critical solution temperature 地临界溶液温度R/D ---- rig down 拆卸设备N/D ---- nipple down 卸下来，拆卸BOPs ---- blowout preventerstack 防喷器组合结构M/U ---- make-up 上扣，连接，接单跟BHA ---- bottom hole assembly 下部钻具结构PV ----- plastic viscosity 塑性粘度YP ----- yield point 屈服点，流动点Sols --- solids 固相含量PH ----- acidity or alkalinity 酸碱度Cond. -- conditioned 处理，调整LOT ----- leak-off test 地层抗破强度试验，套管鞋下边破裂压力试验EMW ---- equivalent mud weight 当量泥浆比重ROP ---- rate of penetration 机械钻速FPH ---- feet per hour 英尺/小时WL ----- water loss 滤失量，失水B/U ---- bring-up 暂停，是停止，中断KCL ---- potassium 氯化钾Stds --- stands 钻杆或钻铤立柱JB ----- junk basket 随钻打捞杯L/D ---- lay down 卸下，甩下，放下RIH ---- run in hole 下钻GB ----- globe basket 牙轮打捞篮Jts ---- joints 单根Bttm --- bottom 底，井底，底部Wt ----- weight 重量，比重WOB ---- weight on bit 钻压DLL ---- dual later log 双侧向测井NGT ----- n atural gammaray spectroscopytool 自然伽马能谱测井LDT ----- l itho-density tool 岩性密度测井HDT ----- h igh-resolution dipmeter tool 高分辨率地层倾角测井MSFL ---- m icro-spherically focusedlog 微球形聚焦测井CNL ----- c ompensatedneutron （porosity） log 补偿中子（孔隙度）测井RFT ----- r epeat-formation tester 重复式地层测试器WST ----- w ell sei**ic tool 井场地震仪Fin. ---- f inish 结束，弄完，干完PB ------ p lugged （plugging） back 打水泥塞，回填CBL ----- c ement bond log 水泥胶结测井VDL ----- v ariable density 变密度测井（=VDC ）CCL ----- c asing collar locator log 套管接箍地位器（测井）Pkr ----- p acker 封隔器DST ----- d rill stem tester 钻柱测试器TP ------ t est pressure 测试压力FSIP ---- f inal shut-in pressure 最终关井压力FSIT ---- f inal shut-in time 最终关井时间F.L. ---- f etch/ load 取出/装入Sudd. --- s uddenly 突然Perf. --- p erforation 射孔，打眼，炮眼Reptd --- r eported 汇报，上报Woo wait on order 等指令Pooh - pull outof hole 起钻DR --- drilling 钻进RM --- reaming 扩眼TOF---top of fish 鱼顶MW —mud weight 泥浆密度CBU -- circulate [ ?s?:kjuleit ] bottoms循环一周upMWD---mersurement while drilling 随钻测量仪KSW --- key seat wiper 键槽清洁器DP -drill pipeHWDP ---- heavy we ight drill pipeDC -- drill collarSTB --- stabilizerSMDC ---- short maganeticdrill collarPDM---positive displacementmotorNMDC---nonmagnetic drill collarBOP---blowout preventer CSC—casingJNT---JointXO---cross overFH—full holeAbbreviationDP ------------------ Drill pipe 钻杆HWDP ---------------- avy weight drill pipe 加眶钻村DC -------------------- II collar 钻铤STB ------------------ ilizcr钻杆扶正器SMIX7 short magnetic drill collar 知无磁钻铤PDM ------------------ sitive displacemeni nicHor 螺杆NMDC ----------------- nonmagnetic drill collar 无磁钻铤（钻JI）BOP ------------------ blowout preventer 时井器CSC ------------------ asing 套管J NT ----------------- joint 单根XO ------------------- cross-over 配合接头IF ------------------- internal flush 内平FH ------------------- lull hole 贯眼REG regular 正规IU ------------------ internal upset 内加与EU ------------------ xternal upset 外加厚IEU ------------------ internal & external upset 内夕卜加1? OH ------------------- open hole 裸眼WOB -------------------- weight on bit 钻压RPM ------------------- volutions per minute 转速分钟SPM stwkcs per minute 冲程每分仲ECD equivalent circulaling density 当量泥为MT --------------------- nieiric （on 公制I地BHA -------------------- bonom hole assembly 底部钻的I合DST -------------------- drill stem test 钻貝测试part number 零件型号 —serial number系列'； 一 nc( weight 净币 —gross weight €朮 -pick up 吊起 —make up 扌攵•上 一lay down 甩开 -nipple up 接上 ・ nipple down 卸丿F rig up 安裝wait on cement 候凝 —run in hole 卜钻 一wail on order 鸽扌旨令viscosity 枯度 waler loss 失水plastic viscosity yield point 屈眼值 —tlltraic loss 濾失 (rue vertical depth 晅深 measured depth 测 uUHX -total depth 总幷課 - kick off point造斜点 —direction 宜向 ・azimuth 方钉DEV ROP FTG- PPG PSI — SGL - HTHP AD 一 LCM- \PI — IADC CNPC一 deviation 井斜—rate of penetration ------ inside-diameter —footage 进尺pounds per gallon机械钻速外径（密度）毎加仑磅pounds per square inch 每平方英寸磅 —ingle 单根 --- high (emperature high pressure 高温高H ； ― sistani driller 副司钻—— lost circulation material 堵漏剂—American petroleum institute iMbl (i 油协会 Internationalassociation drilling contractor 国际钻丿| 承包商 China national pclmlcum company 屮 IN 彳i 油人然气总介 nJASAPP/N S/N — NAV — G/W - P/U —— M心一[— N/U - N/D R/U woe RIH - WOOVIS- WL PV YP — IL- TV 1> MD- TD - KOP DIR AZM。
石油工程钻井井型中英文介绍
（1）直井straight well:井眼轴线大体沿铅垂方向，其井斜角、井底水平位移和全角变化率均在限定范围内的井。
（2）井壁well wall:井眼的圆柱形表面。
（3）井壁well wall:井眼的圆柱形表面。
（4）海上钻井offshore drilling:利用固定式或移动式钻井平台在不同水深的海上进行的钻井。
（5）欠平衡压力钻井under-balanced drilling:是指作用于井底的液柱压力略低于地层孔隙压力情况下的钻井。
（简称UBD）
（6）近平衡压力钻井near balanced drilling:是指作用于井底的液柱压力略大于地层孔隙压力情况下进行的钻井。
（7）塑性岩石plastic rock:在外载作用下直至破碎之前呈现明显塑性变形的岩石。
（8）地温梯度geothermal gradient:地层深度每增加100m,地温增高的度数℃。
（9）微型钻头micro-bit
（10）钻头泥包bit balling:钻头被岩屑、钻井液等掺混在一起的糊状物紧紧包住。
英文钻井日志常用缩写词汇
英文钻井日志常用缩写词汇
（按照钻井施工顺序排列）
DC---------drill collar 钻铤
DP---------drill pipe 钻杆
TD---------true depth 垂直井深
TD---------total depth 总进尺，总深度USG-------united states gallon 美制加仑
Hrs---------hours 小时
Drlg-------drilling 钻进，钻井
Circ--------circulating 循环
Hi. Vis.----high viscosity 高粘度
CSG-------casing 套管
POOH-----pull out of hole 起钻
R/U--------rig up 安装
SXS-------sacks 袋子
WOC------wait on cement 候凝
MW--------mud weight 泥浆比重
N/U--------nipple up 安装
P/U---------pick up 上提，提起
TIH--------trip in hole 下钻
Cmt--------cement 水泥
DCS-------drill collar stem 钻铤柱
ISF---------induction-spherically focused log 感应-球形聚焦测井LSS--------long-space sonic (log) 长源距声波测井GR---------gamma ray log 自然伽马测井LCST------lower critical solution temperature 地临界溶液温度
R/D--------rig down 拆卸设备
N/D--------nipple down 卸下来，拆卸
BOPs------blowout preventer stack 防喷器组合结构
M/U-------make-up 上扣，连接，接单跟
BHA-------bottom hole assembly 下部钻具结构
PV---------plastic viscosity 塑性粘度
YP---------yield point 屈服点，流动点
Sols--------solids 固相含量
PH---------acidity or alkalinity 酸碱度
Cond.------conditioned 处理，调整
LOT--------leak-off test 地层抗破强度试验，套管鞋下边破裂压力试验
EMW------equivalent mud weight 当量泥浆比重
ROP-------rate of penetration 机械钻速
FPH--------feet per hour 英尺/小时
WL---------water loss 滤失量，失水
B/U---------bring-up 暂停，是停止，中断
KCL--------potassium 氯化钾
Stds---------stands 钻杆或钻铤立柱
JB-----------junk basket 随钻打捞杯
L/D---------lay down 卸下，甩下，放下
RIH---------run in hole 下钻
GB----------globe basket 牙轮打捞篮
Jts-----------joints 单根
Bttm--------bottom 底，井底，底部
Wt----------weight 重量，比重
WOB-------weight on bit 钻压
DLL--------dual later log 双侧向测井
NGT--------natural gamma ray spectroscopy tool 自然伽马能谱测井
LDT--------litho-density tool 岩性密度测井
HDT--------high-resolution dipmeter tool 高分辨率地层倾角测井MSFL------micro-spherically focused log 微球形聚焦测井
CNL--------compensated neutron (porosity) log 补偿中子（孔隙度）测井RFT---------repeat-formation tester 重复式地层测试器
WST--------well sei**ic tool 井场地震仪
Fin.---------finish 结束，弄完，干完
PB----------plugged (plugging) back 打水泥塞，回填
CBL--------cement bond log 水泥胶结测井
VDL--------variable density 变密度测井（=VDC）CCL--------casing collar locator log 套管接箍地位器（测井）Pkr----------packer 封隔器
DST---------drill stem tester 钻柱测试器
TP-----------test pressure 测试压力
FSIP--------final shut-in pressure 最终关井压力
FSIT--------final shut-in time 最终关井时间
F.L.---------fetch/ load 取出/装入
Sudd.-------suddenly 突然
Perf.--------perforation 射孔，打眼，炮眼Reptd-------reported 汇报，上报
Woo---- wait on order 等指令
Pooh---- pull out of hole 起钻
DR-----drilling 钻进
RM----reaming 扩眼
TOF---top of fish 鱼顶
MW—mud weight 泥浆密度
CBU---- circulate [ˈsə:kjuleit] bottoms up 循环一周MWD---mersurement while drilling 随钻测量仪KSW---- key seat wiper 键槽清洁器
DP –drill pipe
HWDP----- heavy weight drill pipe
DC----drill collar
STB----stabilizer
SMDC---- short maganetic drill collar
PDM---positive displacement motor
NMDC---nonmagnetic drill collar
BOP---blowout preventer
CSC—casing
JNT---Joint
XO---cross over
FH—full hole。
