Agilent电源使用手册

Ａｇｉｌｅｎｔ电源使用手册69311B/D,69309B/D一前面板显示栏说明的具体意义CV 输出或输出处于固定电压模式CC 输出1或输出2处于固定电流模式Unr 输出或输出不能进行调整Dis输出处于关闭状态按Output On/Off键使输出打开OCP 过电流保护为打开状态按OCP键使过电流保护状态关闭Proc 由于保护功能起作用显示输出已经被禁止按Prot Clear键来清除保护功能Shift Shift键已被按下Rmt 程序控制接口HP-IB,RS232处于工作状态按Local键使电源回到手动控制状态Addr 读写接口的地址口Err SCPI错误序列中出现一个错误按Error键来看错误代码SRQ 接口需要维修二前面板菜单的实际作用前面板控制菜单图示<1> System Keys蓝色无标签的按键就是Shift键起到按键功能转换的作用例如按shift键在显示栏上就显示Shift标示则按键上方标示的功能起作用如Error再次按Shift键则回到按键功能使电源从程序控制状态转换到手动控制状态如果电源已经处于LOCAL状态则local 按键无效ADDRESS <value> 设置HP-IB地址INTF <char> 选择通讯接口HP-IB,RS-232BAUDRATE <char> 选择波特率(300,600,1200,2400,4800,9600)PARITY <char> 消息奇偶性(NONE|EVEN|ODD|MARK|SPACE)FLOW <char> 流控制XON-XOFF|RTS-CTS|DTR-DSR|NONELANG <char> 选择语言(SPCI或COMP)REMOTE FT <char> HP14575A遥控面板的开关(ON/OFF)ROM <char> 固件版本号SN:<char> 电源序列号码按此键可以使直流电源进入以前保存的状态可以返回到前四个保存的状态0 到 3+(Shift + Channel) 输出1和输出2显示转换Display Measurement1<reading>V <reading>A Measures output channel 12<reading>V <reading>A Measures output channel 2 +(Shift + Error) 显示系统错误代码若没有错误显示0+Shift + Save保存目前电源的状态到固定存储器2Function Keys直流电源开状态和关状态的转换当关状态Dis显示在显示栏上+(Shift + Proc Clr) 保护环路复位使电源回到上一个程序状态+(Shift + OCP) 按此键在OCP起作用/不起作用之间切换如果OCP起作用则输出模式不能从定电压转到定电流模式并且OCP指示显示在显示栏中按,提出列表中的下一个命令按返回列表中的前一个命令Display Measurement<reading>V <reading>A 测量输出直流电压和电流<reading>V MAX 测量输出电压的峰值<reading>V MIN 测量输出电压的最小值<reading>V HIGH 测量电压脉冲的最高电平<reading>V LOW 测量电压脉冲的最低电平<reading>A MAX 测量输出电流的峰值<reading>A MIN 测量输出电流的最小值<reading>A HIGH 测量电流脉冲的最高电平<reading>A LOW 测量电流脉冲的最低电平<reading>A RMS 测量均方根值电流<reading>V DC:DVM 通过DVM输入测量直流电压<reading>V RMS:DVM 通过DVM输入测量均方根值电压+(Shift + Input)Display MeasurementCURR:RANGE<char> 选择电流范围AUTO|LOW|HIGHCURR:DET <char> 选择电流测量的带宽(ACDC|DC)TINT <char> 设置前面板测量的间隔15.6us to 1 seconds)POINTS <char> 设置前面板测量缓冲器的测量点数(1,2,4,8,32,64,128,256,512,1024,2048)按此键进入电压设置菜单Display Command Function1 VOLT <value> 设置输出1的电压2 VOLT <value> 设置输出2的电压HP66039B/66039D按此键进入电流设置菜单Display Command Function1 CURR <value> 设置输出1的电流2 CURR <value> 设置输出2的电流HP66039B/66039D按此键进入输出菜单设置列表Display Command Function*RST 设置直流电源回到出厂缺省值TYPE:CAP <char> 设置输出补偿(HIGH|LOW)PON:STATE <chat> 选择开电状态命令(RST|RCL0)PROT:DLY <value> 设置输出保护延迟时间(second)RI <char> 设置远距离约束模式DFI <char> 设置不连续故障指示状态(ON|OFF)DFT:SOUR <char> 选择DFI来源(QUES|OPER|ESB|RQS|OFF)PORT <char> 选择输出端口功能RIDFI/DIGIODIGIO <char> 设置读出I/O端口数0 through 7SENSE:PROT <char> 开环传感导线检测环路开关(ON|OFF)按此键显示保护状态Display Command FunctionOVER CURRENT 保护状态特征over currentNO FAULT 保护状态特征none tripped+(Shift + OV) 按此键进入过电压(overvoltage)保护菜单Display Command FunctionPROT:STAT <char> 打开或关闭过电压保护措施ON|OFF PROT:LEV <value> 设置过电压保护的保护值+(Shift + Cal) 按此键进入校准菜单<3> Entry Keys在特殊命令中的参数列表中进行上下选择增加或减小数值大小在闪光数字中进行左右移动按此键进入数字输入状态0 9 0到9是输入数字.是小数点- 是负号. , 例如输入33.58 按Enter Number,3,3,.,5,8,Enter (back space) 删除最后输入的数字+(Shift + Clear Entry) 按此键放弃输入的数值清除数值按此键执行输入的数值或使参数进入命令里。

Agilent 363xA-Series Programmable dc Power SuppliesData Sheet•Single and triple outputs•80W to 200W output power•Dual output ranges (except E3631A)•Low noise and excellent regulation•High accuracy and resolution•Remote sense (except E3631A)•Front and rear output terminals(E3633/34A only)•GPIB and RS-232 standardClean and stable power with programmability at an affordable priceAffordable programmable power supplies to meet your needsThe E363xA-series of programmable dc power supplies give you the performance of system power supplies without the high price.All models give you clean power, dependable regulation and fast transient response with built-in GPIB and RS-232 interface. E363xA-series are designed to meet the most demanding applications in R&D design verifications, production testing, and QA verifications with traditional quality and reliability you can count on.Excellent Performance you can trust0.01% load and line regulation keep the output steady when power line and load change occur. The power supplies specify both normal mode voltage/current noise and commonmode current noise.The low normalmode noise specification assuresclean power for precision circuitryapplications and the low commonmode current provides isolation frompower line current injection.Remote InterfaceIf you have an IEEE-488 card orRS-232 in a PC, these power supplieswill work for you. Every model comesequipped with both GPIB and RS-232as standard. All programming isdone in easy to use SCPI (StandardCommands for ProgrammableInstruments). The user’s guidedescribes the process for first timeprogrammers.Front Panel OperationA knob and self-guiding keypadsallow you to set the output at theresolution you need for the mostexacting adjustments quickly andeasily. Up to three complete powersupply setups can be stored andrecalled from the internal non-volatilememory. The output on/off buttonsets the output to zero.E3631A triple-output power supplyThis famous 80-watt triple outputsupply offers three independent0to +6 V/5 A and 0 to ±25 V/1 Aoutputs. The6V output is electricallyisolated from the ±25 V supply tominimize any interference betweencircuits under tests. The±25 Voutputs can be set to track each other.E3632A/33A/34A single-output dual rangepower suppliesThese single output power suppliesgive you the flexibility to select fromdual output ranges. Output load isprotected against overvoltage andovercurrent, which are easily mon-itored and adjusted from the frontpanel and remote interface. Remotesense is available to eliminate theerrors due to voltage drops on theload leads. E3633A/34A offers frontand rear output terminals. Agilent Technologies2Ordering Information E3630-Series Power Supplies E3631A 80-Watt Triple Power Supply E3632A 120-Watt Single Power Supply E3633A/34A 200-Watt Single Power Supply Power OptionsOpt. 0E3 230 Vac ±10%Opt. 0E9 100 Vac ±10%Other OptionsOpt. W50 Additional 2-year warranty (5-year total)Opt. 910 Extra manual sets Opt. 1CM Rack-mount kitRack Mount Kits E3631A/32A/33A/34ATo rack mount two instruments side by side Lock-link Kit(P/N 5061-9694)Flange Kit(P/N 5063-9214)To rack mount two instruments in a sliding support shelfSupport Shelf (P/N 5063-9256)Slide Kit (P/N 1494-0015)Agilent TechnologiesAgilent Technologies ’ Test and Measurement Support, Services, and AssistanceAgilent Technologies aims to maximize the value you receive, while minimizing your risk and problems. We strive to ensure that you get the test and measurement capabilities you paid for and obtain the support you need. Our extensive support resources and services can help you choose the right Agilent products for your applications and apply them successfully.Every instrument and system we sell has aglobal warranty. Support is available for at least five years beyond the production life of theproduct. Two concepts underlie Agilent’s overall support policy: “Our Promise” and “Your Advantage.”Our PromiseOur Promise means your Agilent test andmeasurement equipment will meet its advertised performance and functionality. When you are choosing new equipment, we will help you with product information, including realistic performance specifications and practical recommendations from experienced test engineers. When you use Agilent equipment, we can verify that it works properly, help with product operation, and provide basic measurement assistance for the use ofspecified capabilities, at no extra cost upon request. Many self-help tools are available.Your AdvantageYour Advantage means that Agilent offers a wide range of additional expert test and measurement services, which you canpurchase according to your unique technical and business needs. Solve problems efficiently and gain a competitive edge by contracting with us for calibration,extra-cost upgrades, out-of-warranty repairs, and on-site education and training, as well as design, system integration,project management,and other professional engineering services. Experienced Agilent engineers and technicians worldwide can help you maximize your productivity, optimize the return on investment of your Agilent instruments and systems, and obtaindependable measurement accuracy for the life of those products.。

用户指南Agilent T echnologies E3632ADC 电源版权© 1997-2000安捷伦科技公司(Agilent Technologies)保留所有权利出版历史第 2版2000 年10 月新版手册是对原手册的完整修订每版之间的更新内容将以附加页和更换页的方式供您合并到本手册中本页的日期只有在新版发行时才更改商标信息Windows Windows 95 和 Windows NT 是 Microsoft Corp.的注册商标产品认证安捷伦科技公司认证本产品自出厂时符合其公布的规格安捷伦进一步认证本产品的校准测量符合美国国家标准和技术局此前为国家标准局为校准设备规定的测量范围并符合其它国际标准组织成员的校准设备的标准保修安捷伦对本产品的材料及工艺自出厂之日起给予为期三年的质量保证本产品与其它安捷伦产品集成时成为其它安捷伦产品的一部分安捷伦可改变本产品的保修期限和条件在保用期内安捷伦将负责维修或更换由安捷伦自行决定经证实有缺陷的产品保修期自交货之日起或自安装之日起如果由安捷伦安装开始计算保修服务本产品如果需要保证服务或修理必须将其送回安捷伦维修部门将产品送回安捷伦进行保修服务时用户应预付发往安捷伦的运费安捷伦则负责支付返程运费然而如果从其它国家将产品送回安捷伦则所有的运费关税及其它税款均由用户负担保修限制上述保修条件不适用于由以下原因所造成的损坏不正确或不适当地维修产品用户使用自己的产品或界面未经授权地修理或误用在指定环境外操作本产品或在不恰当的现场装配和维修等本产品的任何电路设计和连接完全由用户自行负责安捷伦不保证用户自行安装的电路的性能以及由此造成的安捷伦产品的故障除上述保证外没有任何其它明示或暗示的保证在当地法律允许的情况下安捷伦对本产品不作任何其它口头形式或书面形式上的明示或暗示的保证并且特别声明没有涉及特定用途的适销性或适用性或满意质量的暗示保证或条款对于澳大利亚和新西兰的交易:除非法律许可本声明中所含条款并不排除限制或修改适用于本产品销售的强制性法定权利而是对其的补充唯一的补救方法在当地法律允许的情况下此处提供的补救方法是用户唯一且仅有的补救方法安捷伦对任何直接间接特殊偶然或继发的损失包括失去利润或丢失数据无论是根据合同侵权赔偿或任何其它法理都概不负责声明本文档中包含的信息如有变动恕不另行通知在当地法律允许的情况下安捷伦对本资料不作任何的保证包括但不仅限于特定目的适销性和适用性的暗示保证对本资料可能包含的错误或因提供执行或使用本资料而导致的任何偶然和继发的损失安捷伦概不负责未经安捷伦事先书面许可不得影印复制或改编本文档的任何部分限制的权利软件和文档完全以个人经费开发它们根据下列条款交货并获得许可这些条款中的任何一个都适用DFARS 252.227-70131988 年 10月DFARS 252.211-70151991 年 5月或DFARS 252.227-70141995 年 6月中定义的商业计算机软件FAR 2.101(a) 中定义的商业条款或FAR 52.227-191987 年 6月或任何等同的代理规定或合同条款中定义的限制的计算机软件您对软件和文档资料只拥有 FAR 或 DFARS 相应条款或所涉及产品的安捷伦标准软件协议中规定的权利安全信息不要在本产品上安装替代零件或执行任何未经授权的修改请将本产品送回安捷伦销售与维修部门维修以确保其安全特性安全符号警告提醒使用者注意可能导致人员伤亡的操作程序做法或情况等注意提醒使用者注意可能导致仪器损坏或数据永久丢失的操作程序做法或情况等接地地线符号机架地线符号请参考手册中的特定警告和注意信息以避免人员伤害或设备损坏可能存在危险电压警告仪器内部没有操作人员可维修的部件如果需要维修服务请与受过培训维修人员联系警告要预防火灾更换的保险丝必须符合指定的类型和额定电流!手册编号E3632-904182000 年 10月第2版马来西亚印刷Agilent E3632A 是配有 GPIB 和 RS-232 接口的直流电源可提供高性能的 120 瓦单一输出具有两种输出量程它将工作台功能与系统功能相结合针对您的设计和测试要求提供了多用途解决方案便利的工作台功能•双量程单一输出•易于使用的旋钮控制设置•高可见度的真空荧光显示器•高精度和高解析度•远程电压检测•过压保护和过流保护•输出开/关•出色的负载和线路稳压以及低波纹和低噪声•操作状态存储•带有防滑支脚的便携式耐用机箱灵活的系统功能•GPIB (IEEE-488) 和 RS-232 接口是标准配置•SCPI可编程仪器的标准命令兼容性•易于从前面板完成的 I/O 设置•软件校准因此不必进行内部调整Agilent E3632A DC 电源前面板总览1 15V/7A 量程选择键2 30V/4A 量程选择键3过压保护键4过电流保护键5极限显示键6调用操作状态键7存储操作状态/本地键 8错误/校准键9 I/O 配置/加密键10输出开/关键11控制旋钮12解析度选择键13电压/电流调整选择键23115V/7A 量程选择键 用于选择 15V/7A量程并允许 15V/7A满量程输出230V/4A 量程选择键 用于选择 30V/40A 量程并允许 30V/4A满量程输出3过压保护键用于启用或禁用过压保护功能设置断路电压电平和清除过压状态4过流保护键用于启用或禁用过电流保护功能设置断路电流电平和清除过流状态5极限显示键用于在显示屏上显示电压和电流极限值可使用旋钮设置极限值6调用操作状态键从位置12或3调用先前存储的操作状态7存储操作状态/本地键1将操作状态存储在位置12或3或者使电源从远程界面模式返回本地模式8错误/校准键2 显示操作过程自检和校准时产生的错误码或者启用校准模式电源在执行校准前必须已解密有关如何校准的详细信息参见Service Guide 9I/O 配置/安全键3 配置远程界面的电源/或者对电源校准进行加密或解密有关如何对电源加密与解密的详细信息参见Service Guide 10输出开/关键启用或禁用电源输出此键在开和关之间切换11控制旋钮通过顺时针或逆时针旋转增加或减少闪烁数字的值12解析度选择键将闪烁的数字左移或右移13电压/电流调整选择键选择电压或电流调节的旋钮控制功能1当电源处于远程界面模式时此键可作为本地键使用2启动电源时可按住此键启用校准模式3当电源处于校准模式时此键可作为加密或解密键使用4前面板的电压和电流极限设置可用以下方法从前面板设置电压和电流极限值12键以在显示屏上显示极限值3并用控制旋钮将闪烁的数值如果极限显示超时则再次按4电流调整选择键将旋钮设置为电流控制模式5用解析度选择键将闪烁的数字移到相应的位置并用控制旋钮将闪烁的数字值改为所需的电流极限值6按下 键以启用输出大约五秒钟后显示屏自动进入输出监视模式显示输出的电压和电流或者再次按 键显示屏将立即进入输出监视模式注可使用远程界面命令禁用所有的前面板键和控制钮Agilent E3632A 必须处于本地模式时前面板键和控制钮才会起作用电流调整选择键解析度选择键和控制旋钮Display Limit Output On/Off Output On/Off5显示屏指示灯Adrs表明电源通过远程界面收听或通话Rmt表明电源处于远程界面模式15V 表明所选的是 15V/7A量程30V 表明所选的是 30V/4A量程OVP指示灯亮时表明启用了过压保护功能或者在指示灯闪烁时表明过压保护电路导致电源关闭OCP 指示灯亮时表明启用了过电流保护功能或者在指示灯闪烁时表明过流保护电路导致电源关闭CAL表明电源处于校准模式Limit 表明显示屏显示的是电压和电流的极限值ERROR 检测到硬件或远程界面命令有错误且尚未清除错误位OFF禁用了电源输出详细信息参见第 33页Unreg电源的输出不稳定既不是 CV 输出也不是 CC输出CV电源处于恒压模式CV电源处于恒定电流模式要查看显示屏指示灯请在启动电源时按下键Display Limit后面板总览使用前面板键以•选择 GPIB 或 RS-232 接口参见第 3 章•设置 GPIB 总线地址参见第 3 章•设置 RS-232 的波特率和奇偶校验参见第 3 章1电源线电压设置2电源线保险管座3交流电源输入接口4电源线模块5 GPIB (IEEE-488) 接口连接器6 RS-232 接口连接器I/O Config67本书内容概述 第 1章是电源的一般性介绍此外还提供有关检查电源连接交流电源以及选择电源线电压的规程初始操作 第 2 章确保电源产生额定输出并正确地响应前面板的操作前面板操作 第 3章详细介绍前面板键的用法以及如何使用这些键从前面板操作电源此外还讲述了如何配置电源的远程界面并简要地介绍了提供校准功能远程界面参考资料 第 4 章所含的参考信息可以帮助您通过远程界面对电源编程此外还介绍如何对状态报告编程错误消息 第 5 章列出使用电源时可能出现的错误消息每条错误消息列出了有助于您诊断并解决问题的信息应用程序 第 6 章提供了某些远程界面应用程序可帮助您开发自己的应用程序教程 第 7章介绍线性电源的基本操作并提供有关操作和使用 AgilentE3632A电源的具体细节规格 第 8章列出电源的技术规格如果您有电源操作方面的问题在美国请拨打电话1-800-452-4844 或就近与安捷伦科技公司的销售部门联系如果自购买之日起三年内Agilent E3632A 出现故障安捷伦将免费修理或更换在美国请拨打电话 1-800-258-5165ExpressExchange或就近与安捷伦科技公司的销售部门联系8目录第 1 章概述安全注意事项 14安全和 EMC 要求 14选件和附件 15选件 15附件 15说明 16安装 19初始检查 19冷却和安置 19输入电源要求 22电源线 22电源线电压选择 22第 2 章初始操作初步检查 27加电检查 28输出检查 29电压输出检查 29电流输出检查 30第 3 章前面板操作前面板操作概述 33恒压操作 34恒定电流操作 36存储和调用操作状态 38编写过压保护程序 40设置 OVP 电平和启用 OVP 电路 40检查 OVP 操作 41清除过压状态 41编写过流保护程序 43设置 OCP 电平和启用 OCP 电路 43检查 OCP 操作 44清除过流状态 44进行远程电压检测 46CV 稳压 46额定输出 46输出噪声 46稳定性 46远程电压检测连接 47禁用输出 489目录使用外部继电器禁用输出 49旋钮锁定 49与系统相关的操作 50自检 50出错状况 51显示屏控制 52固件版本查询 53SCPI 语言版本 53远程界面配置 54远程界面选择 54GPIB 地址 55波特率选择 (RS-232) 55奇偶校验选择 (RS-232) 55设置 GPIB 地址 56设置波特率和奇偶校验 (RS-232) 57GPIB 接口配置 59RS-232 接口配置 60RS-232 配置概述 60RS-232 数据帧格式 60连接到计算机或终端 61DTR / DSR 信号交换协议 62RS-232 故障排除 63校准概述 64校准加密 64校准信息 68第 4 章远程界面参考资料SCPI命令摘要 71简化的编程概述 76使用APPLy命令 76使用低级命令 76读取查询响应 77选择触发源 77电源编程范围 78使用APPLy命令 79输出设置和操作命令 80触发命令 86触发源选择 86触发命令 88与系统相关的命令 89校准命令 93RS-232 接口命令 951011目录SCPI 状态寄存器 96什么是事件寄存器 96什么是允许寄存器 96SCPI 状态系统 97可疑状态寄存器 98标准事件寄存器 99状态字节寄存器 100使用服务请求 (SRQ) 和串行查询 101使用 *STB? 命令读取状态字节 102使用信息可用位 (MAV) 102使用 SRQ 中断总线控制器 102确定命令序列何时完成 103当数据位于输出缓冲区时使用 *OPC 发出信号 103状态报告命令 104SCPI 语言简介 106本手册使用的命令格式 107命令分隔符 108使用 MIN 和 MAX 参数 108查询参数设置 109SCPI 命令终止符 109IEEE-488.2 常用命令 109SCPI 参数类型 110暂停进行中的输出 111SCPI 符合信息 112IEEE-488 符合信息 115第 5 章 错误消息执行错误 119自检错误 124校准错误 125第 6 章 应用程序用于 GPIB(IEEE 488) 的 C++ 实例 129Windows 3.1 和 GPIB 的 Excel 5.0 实例 131第 7 章 教程Agilent E3632A 操作概述 137输出特性 139不稳定状态 141干扰信号 141目录连接负载 143输出绝缘 143多个负载 143远程电压检测 144负载考虑事项 145扩大电压和电流的输出范围 146串联连接 146并联连接 146远程编程 147可靠性 149第 8 章规格性能规格 153补充特性 155索引 159Declaration of Conformity 163 121概述14概述本章对电源进行了一般性介绍并提供了有关初始检查在工作台和机架中安置及冷却电源选择电源线电压以及将电源与交流电源连接的操作规程安全注意事项本电源是 I类安全仪器这表明它有保护性接地端子该端子必须通过带有三线接地插座的供电电源与地线连接在安装或操作之前应首先检查电源并回顾本手册中介绍的安全标记和操作规程具体步骤的安全信息位于本手册的相应章节中有关一般的安全信息另见本手册开始部分的安全信息安全和 EMC 要求本电源的设计符合下列安全和EMC电磁兼容性要求•IEC 1010-1(1990)/EN 61010-1(1993) + A2 (1995): Safety Requirements for Electrical Equipment for Measurement, Control, and Laboratory Use•CSA C22.2 No.1010.1-92: Safety Requirements for Electrical Equipment for Measurement, Control, and Laboratory Use•UL 1244: Electrical and Electric Measuring and Testing Equipment •EMC Directive 89/336/EEC•Low Voltage Directive: 73/23/EEC•EN 55011(1991) Group I, Class A/CISPR II(1990): Limits and Methods of Radio Interface Characteristics of Industrial, Scientific, and Medical(ISM) Radio-Frequency Equipment.•EN50082-1(1992):IEC 801-2(1991): Electrostatic Discharge RequirementsIEC 801-3(1984): Radiated Electromagnetic Field RequirementsIEC 801-4(1988): Electrical Fast Transient/Burst Requirements第 1章概述选件和附件151选件和附件选件选件0E3和0E9决定了出厂时选择哪种电源线电压标准单元的配置为 115 Vac ± 10%47-63 Hz 输入电压有关更改电源线电压设置的更详细信息请参见从本章第 22 页开始的电源线电压选择选件说明0E3230 Vac ± 10%, 47-63 Hz 输入电压0E9100 Vac ± 10%, 47-63 Hz 输入电压1CM机架安装工具包安捷伦产品编号5063-9243910额外的一套手册所使用的语言与您订购电源时选择的手册语言相同*附件下列附件可从当地安捷伦科技公司销售部门单独订购或与电源一起订购安捷伦编号说明10833A GPIB电缆 1 米 3.3 英尺10833B GPIB电缆 2 米 6.6 英尺34398A RS-232, 9 针孔端转 9 针孔端 2.5 米8.2 英寸电缆另加9 针针端转25针孔端转接器34399ARS-232 转接器套件内含 4个转接器用于 PC或打印机的 9 针针端转 25 针针端转接器用于 PC 或打印机的 9 针针端转 25 针孔端转接器用于调制解调器的 9 针针端转 25针针端转接器用于调制解调器的 9 针针端转 9 针针端转接器*要订购单独的一套用户指南和Service Guide请订购安捷伦编号为E3632-90408 的产品第 1章 概述说明16说明Agilent E3632A DC电源兼有编程功能和线性电源的性能最适合作为供电系统使用可在本地从前面板或在远程通过 GPIB 和 RS-232接口对电源进行编程本电源具有两个量程允许在电流较低时有较高的电压或者电压较低时有较高电流您可从前面板或从远程界面选择所需的输出量程操作特性包括•15V/7A 或 30V/4A 的两个量程•恒压 (CV) 或恒定电流 (CC) 操作•过压保护 (OVP) 和过流保护 (OCP)•有三个存储位置 1 到 3可用于存储用户定义的操作状态•自动开机自检•负载电压的远程检测•用户可从前面板或通过远程界面校准前面板操作包括•操作简单的旋钮控制•输出量程选择•启用或禁用 OVP 和 OCP 功能•设置 OVP 和 OCP 断路电平•清除 OVP 和 OCP 状态•设置和显示电压和电流极限值•保存和调用操作状态•使电源从远程界面模式返回本地模式•显示远程界面错误消息•校准电源包括更改校准密码•配置电源的远程界面•启用或禁用输出第 1章 概述说明171从远程界面操作时电源可同时作为收话方和通话方使用外部控制器您可以指示电源设置输出并通过 GPIB 或 RS-232 传回状态数据包括下列功能•电压和电流编程•电压和电流回读•当前和已存储状态的回读•编程语法错误检测•完整的自检前面板VFD真空荧光屏包括•显示输出电压和电流的实际值计量模式•或显示电压和电流的极限值极限模式•通过指示灯检查操作状态•通过错误代码错误消息检查错误类型将电源的输出和机座地线连接到前面板的接线柱上警告 如果电源输出浮置电压大于 ±60 Vdc 则操作者在机座处即有遭受电击的危险当使用未绝缘的金属短路条将 (+) 输出端子与 (+) 检测端子相连并将 (-) 输出端子和 (-) 检测端子相连时不要使输出浮置电压大于±60 Vdc第 1章 概述说明18警告 如果用绝缘体代替未绝缘的金属短路条或从端子上取下这些短路条以便任何操作者都不会接触到未绝缘输出导体则最大输出浮置电压可以达到 ±240 Vdc 现场所有导线的绝缘必须满足当前电压的要求电源附带有可拆卸的三线接地型电源线交流电源线的保险管位于后面板上可以取出可直接从前面板或通过 GPIB 或 RS-232 接口上的控制器使用校准命令校准电源校正系数存储在非易失性存储器中在输出编程时使用从前面板或控制器校准时不必卸下顶盖甚至不需要将电源从系统机箱中取出使用加密校准保护功能可以防止未经授权的校准第 1章 概述安装191安装初始检查当您收到电源时检查一下其在运输过程中是否发生了明显的损坏如有任何损坏请立即通知运输公司并与最近的安捷伦销售部门联络保修信息在本手册的最前面保存好包装材料以备将来将电源送回安捷伦科技公司时使用如要将电源送回安捷伦维修请随附一份标识物主和仪器型号的卡片并附上问题简述机械性检查通过此项检查确认键或旋钮没有破损机壳和面板表面没有凹陷和刮痕显示屏也没有刮痕或破裂电气检查第 2 章介绍了初始操作步骤如果成功地完成这些步骤即可确信电源正按照技术规格的要求运行Service Guide 中提供了详细的电气检验步骤冷却和安置冷却电源在 0°C到 40°C 的温度范围内运行时不会降低性能在40 °C到 55 °C 的情况下输出电流会降低风扇通过后面板抽进空气并从侧面排出以使电源冷却使用安捷伦的架装套件不会阻碍空气流通工作台操作安装电源时应在其两侧及后面留出足够空间以便空气流通安装在机架中时必须卸下橡皮缓冲垫第 1章 概述安装20机架安装可以使用三个选件工具包之一将电源安装在标准的 19英寸机架内选件1CM 安捷伦产品编号5063-9243是用于单个仪器的架装套件每个架装套件中都有安装规程和硬件任何同样尺寸的 Agilent System II 仪器都可架装在 E3632A 电源的旁边在架装电源之前应先拆下前后缓冲垫要卸下橡皮缓冲垫应先拉住一角然后将其滑出要架装单个仪器请订购转接器套件5063-9243第 1章 概述安装211要并排架装两个仪器请订购链锁套件 5061-9694 和边缘套件 5063-9214要在滑动支架上安装一或两台仪器请订购支架 5063-9256 和滑轨套件 1494-0015对于单个仪器还需订购填充板5002-4002第 1章 概述输入电源要求22输入电源要求可以在额定值为100 V 115 V 或230 V 频率为 47 到 63 Hz 的单相交流电下操作电源后面板上有一个标识指示出厂时设置的电源额定输入电压必要时可根据下一页的指示修改电源线电压的设置电源线电源出厂时配备有电源线其带有符合使用国标准的插头如果配备了错误的电源线请与最近的安捷伦科技公司销售和维修部门联系电源配备有三线接地型电源线第三根导线是地线只有在电源线插入正确的插座时电源才会接地仪器机箱未正确接地之前请勿操作电源电源线电压选择通过调整两个部件可完成电源线电压选择电源线电压选择器与后面板电源线模块上的电源线保险管要改变电源线电压请执行以下步骤第 1章 概述输入电源要求231安装正确的保险管 从电源线模块中卸下电源线电压选择器115 Vac 4 AT 230 Vac 2.5 AT 保险管断开电源线 使用平头螺丝刀从后面板上卸下保险管座旋转电源线电压选择器直到出现正确的电压100115 和保险管座重新装到后面板中第 1章概述输入电源要求242初始操作26初始操作本章介绍了三项基本测试自动加电测试包括自检它检查内部微处理器并让用户直观地检查显示屏输出检查可确保电源产生额定输出并正确地响应前面板的操作有关完整的性能和/或验证测试参见Service Guide 有经验的用户和无经验的用户都应参阅本章内容以便在操作仪器前先执行特定的检查在本章中所使用的按键显示在左页边中第 2章 初始操作初步检查272初步检查以下步骤可帮助您检验电源是否可用1验证后面板上电源线电压的设置电源出厂时为使用国设置了合适的电源线电压值如果电压不正确请修改电压设置设置值有100115 或230 Vac2确保已安装正确的电源线保险管电源出厂时安装了合适于使用国的保险管用于 100 或 115 Vac 操作时必须使用 4 AT 保险管用于 230 Vac操作时必须使用 2.5 AT保险管3接上电源线并打开电源当您打开电源时前面板显示屏变亮同时自动进行加电自检如果需要更改电源线电压或电源线保险管请参见从第 22 页开始的电源线电压选择要更换 4 AT 保险管请订购安捷伦产品编号为 2110-0996 的产品要更换 2.5 AT 保险管请订购安捷伦产品编号为 2110-0999 的产品第 2章 初始操作加电检查28加电检查加电测试包括自动自检它检查内部的微处理器并让用户直观地检查显示屏打开前面板电源开关后您会在显示屏上依次观察到下列情况1显示屏上的所有字段包括所有指示灯将点亮大约1秒钟要检查指示灯请在打开电源时按住键2GPIB 地址或 RS-232 信息将显示约 1 秒钟电源出厂时在远程界面配置中将 GPIB 地址设置为5如果不是首次打开电源则可能会出现不同的界面 (RS-232) 或不同的 GPIB 地址如果需要更改远程界面配置请参见从第3 章第 54 页开始的远程界面配置315VOVPOCP和OFF 指示灯变亮其余的指示灯熄灭电源将进入加电/复位状态输出为禁用OFF 指示灯变亮选择15V/7A 量程15V 指示灯变亮并且选择用旋钮控制电压注意 OVP 和 OCP 指示灯也同时变亮4 启用输出按 键以启用输出OFF 指示灯熄灭而 15V OVP OCP 和 CV 指示灯变亮旋转旋钮可调整闪烁的数字注意显示屏处于计量模式计量模式是指显示屏显示实际的输出电压值和电流值注如果在加电自检时电源检测到错误则 ERROR 指示灯变亮详细信息参见第 5 章第 117 页的错误消息ADDR 05 (或 RS-232)Display Limit Output On/OffOutput On/Off。

Ａｇｉｌｅｎｔ电源使用手册69311B/D,69309B/D一前面板显示栏说明的具体意义CV 输出或输出处于固定电压模式CC 输出1或输出2处于固定电流模式Unr 输出或输出不能进行调整Dis输出处于关闭状态按Output On/Off键使输出打开OCP 过电流保护为打开状态按OCP键使过电流保护状态关闭Proc 由于保护功能起作用显示输出已经被禁止按Prot Clear键来清除保护功能Shift Shift键已被按下Rmt 程序控制接口HP-IB,RS232处于工作状态按Local键使电源回到手动控制状态Addr 读写接口的地址口Err SCPI错误序列中出现一个错误按Error键来看错误代码SRQ 接口需要维修二前面板菜单的实际作用前面板控制菜单图示<1> System Keys蓝色无标签的按键就是Shift键起到按键功能转换的作用例如按shift键在显示栏上就显示Shift标示则按键上方标示的功能起作用如Error再次按Shift键则回到按键功能使电源从程序控制状态转换到手动控制状态如果电源已经处于LOCAL状态则local 按键无效ADDRESS <value> 设置HP-IB地址INTF <char> 选择通讯接口HP-IB,RS-232BAUDRATE <char> 选择波特率(300,600,1200,2400,4800,9600)PARITY <char> 消息奇偶性(NONE|EVEN|ODD|MARK|SPACE)FLOW <char> 流控制XON-XOFF|RTS-CTS|DTR-DSR|NONELANG <char> 选择语言(SPCI或COMP)REMOTE FT <char> HP14575A遥控面板的开关(ON/OFF)ROM <char> 固件版本号SN:<char> 电源序列号码按此键可以使直流电源进入以前保存的状态可以返回到前四个保存的状态0 到 3+(Shift + Channel) 输出1和输出2显示转换Display Measurement1<reading>V <reading>A Measures output channel 12<reading>V <reading>A Measures output channel 2 +(Shift + Error) 显示系统错误代码若没有错误显示0+Shift + Save保存目前电源的状态到固定存储器2Function Keys直流电源开状态和关状态的转换当关状态Dis显示在显示栏上+(Shift + Proc Clr) 保护环路复位使电源回到上一个程序状态+(Shift + OCP) 按此键在OCP起作用/不起作用之间切换如果OCP起作用则输出模式不能从定电压转到定电流模式并且OCP指示显示在显示栏中按,提出列表中的下一个命令按返回列表中的前一个命令Display Measurement<reading>V <reading>A 测量输出直流电压和电流<reading>V MAX 测量输出电压的峰值<reading>V MIN 测量输出电压的最小值<reading>V HIGH 测量电压脉冲的最高电平<reading>V LOW 测量电压脉冲的最低电平<reading>A MAX 测量输出电流的峰值<reading>A MIN 测量输出电流的最小值<reading>A HIGH 测量电流脉冲的最高电平<reading>A LOW 测量电流脉冲的最低电平<reading>A RMS 测量均方根值电流<reading>V DC:DVM 通过DVM输入测量直流电压<reading>V RMS:DVM 通过DVM输入测量均方根值电压+(Shift + Input)Display MeasurementCURR:RANGE<char> 选择电流范围AUTO|LOW|HIGHCURR:DET <char> 选择电流测量的带宽(ACDC|DC)TINT <char> 设置前面板测量的间隔15.6us to 1 seconds)POINTS <char> 设置前面板测量缓冲器的测量点数(1,2,4,8,32,64,128,256,512,1024,2048)按此键进入电压设置菜单Display Command Function1 VOLT <value> 设置输出1的电压2 VOLT <value> 设置输出2的电压HP66039B/66039D按此键进入电流设置菜单Display Command Function1 CURR <value> 设置输出1的电流2 CURR <value> 设置输出2的电流HP66039B/66039D按此键进入输出菜单设置列表Display Command Function*RST 设置直流电源回到出厂缺省值TYPE:CAP <char> 设置输出补偿(HIGH|LOW)PON:STATE <chat> 选择开电状态命令(RST|RCL0)PROT:DLY <value> 设置输出保护延迟时间(second)RI <char> 设置远距离约束模式DFI <char> 设置不连续故障指示状态(ON|OFF)DFT:SOUR <char> 选择DFI来源(QUES|OPER|ESB|RQS|OFF)PORT <char> 选择输出端口功能RIDFI/DIGIODIGIO <char> 设置读出I/O端口数0 through 7SENSE:PROT <char> 开环传感导线检测环路开关(ON|OFF)按此键显示保护状态Display Command FunctionOVER CURRENT 保护状态特征over currentNO FAULT 保护状态特征none tripped+(Shift + OV) 按此键进入过电压(overvoltage)保护菜单Display Command FunctionPROT:STAT <char> 打开或关闭过电压保护措施ON|OFF PROT:LEV <value> 设置过电压保护的保护值+(Shift + Cal) 按此键进入校准菜单<3> Entry Keys在特殊命令中的参数列表中进行上下选择增加或减小数值大小在闪光数字中进行左右移动按此键进入数字输入状态0 9 0到9是输入数字.是小数点- 是负号. , 例如输入33.58 按Enter Number,3,3,.,5,8,Enter (back space) 删除最后输入的数字+(Shift + Clear Entry) 按此键放弃输入的数值清除数值按此键执行输入的数值或使参数进入命令里。

ErrataTitle & Document Type: 6212B/6214B/6216B/6218B DC Power Supply Operating and Service ManualManual Part Number: 5950-1928Revision Date: November 1982About this ManualWe’ve added this manual to the Agilent website in an effort to help you support your product. This manual provides the best information we could find. It may be incompleteor contain dated information, and the scan quality may not be ideal. If we find a bettercopy in the future, we will add it to the Agilent website.HP References in this ManualThis manual may contain references to HP or Hewlett-Packard. Please note that Hewlett- Packard's former test and measurement, life sciences, and chemical analysisbusinesses are now part of Agilent Technologies. The HP XXXX referred to in this document is now the Agilent XXXX. For example, model number HP8648A is now model number Agilent 8648A. We have made no changes to this manual copy.Support for Your ProductAgilent no longer sells or supports this product. You will find any other availableproduct information on the Agilent Test & Measurement website:Search for the model number of this product, and the resulting product page will guideyou to any available information. Our service centers may be able to perform calibrationif no repair parts are needed, but no other support from Agilent is available.。

Agilent 34450A Multimeter5.5 Digit Dual Display, Benchtop DMMData Sheet► Fast reading speed of up to 190 readings/sec ► 0.015% DCV accuracy► Multiple connectivity options – USB 2.0, Serial Interface (RS-232), and GPIB► 11 measurement functions; DC voltage & current, True RMS AC voltage & current, 2- and 4-wire resistance, frequency, continuity, diode test, capacitance, and temperature ► Ultra-bright OLED with dual display capability► Up to 50,000 memory points for data logging and histogram function ► Built-in Histogram function► With Fluke 45 and Fluke 8808A code compatibilityAchieve throughput breakthroughTurbo charge your production line with the 34450A digital multimeter. With its fast speed of up to 190 readings per second you can now increase your manufacturing throughput tremendously. Get highly accurate, repeatable and trustworthy measurements with the 0.015% DCV accuracy designed to meet generalindustrial and educational needs.Figure 1. Bright OLED display for excellent viewing experience when making measurements.►FeaturesIntuitive andMultipurpose deviceThe 34450A is an intuitive and easy to use tool that provides a wide range of measurement functions such as DC voltage, DC current, True RMS AC voltage and AC current, 2-wire and 4 wire resistance, frequency, diode test, continuity, capacitance and temperature. Simplify your day-to-day task with up to 50,000 memory points, allowing you to capture and log up to 14 hours of data. Built-in with histogram and basic statistical functions, you can now do simple data analysis within the unit itself. With its ultra-bright OLED dualdisplay, different measurements can be performed ensuring you get the right readings at first glance.More flexibility with multiple connectivityMultiple connectivity options such as USB 2.0, Serial Interface (RS-232) and GPIB port provides greater flexibility to connect DMM to a PC for data access and retrieval for analysis. With the option to connect to a PC, this enables the 34450A to work with Agilent Connectivity software and can be controlled remotely via SCPI commands or Command Expert. The IVI-COM driver is also included to ensure an easy integration with different programming environments.Easy migrationUpgrading your obsoleted DMM is made easy with minimal changes to test program. To ensure both forward and backward compatibility, the 34450A includes SCPI, Fluke 45 or Fluke 8808A commands. Experience a quick, easy and painless migration as it allows you to quickly transfer your existing test programs on theAgilent 34450A.Up to 50,000 memory points for data logging and histogram functionMultiple choices of connectivity and trigger in/out capability for production data analysisKensington lock to better secure the unitFast 190 readings/sec and 0.015% DCV accuracy to help you achieve throughput breakthrough5.5 digit OLED dual display allows clear and quick view on measurements11 measurement functions; DC voltage & current, True RMS AC voltage & current, frequency, continuity, diode test, capacitance, and temperatureBuilt-in Math functionsInput terminalsTable 1. DC Accuracy ± (% of reading + % of range)Notes on Specifications:1. Specifications are for 90 minutes warm-up time, slow mode and calibration temperature within 18 °C - 28 °C.2. 20% over range on all ranges except 1000 VDC and 10 A range.3. Specifications are for 4 wire Ω or 2-wire Ω using NULL function. If without NULL function, add 0.2 Ω additional error.4. Continuity thresholds is fixed at less than 10Ω5.Specifications are for the voltage measured at the input terminals only.Table 2. AC Accuracy ± (% of reading + % of range)Notes on Specifications:1. Specifications are for 90 minutes warm-up time, slow mode and calibration temperature within 18 °C - 28 °C.2. 20% over range on all ranges except ACV 750 V and ACI 10 A.3. Specifications are for sine wave inputs more than the 5% of range except 750 V range. Input signal must be more than 50 Vrms for 750 V range. Maximum crest factor of 3 at full scale. Input impedance is 1 MΩ in parallel with capacitance less than 120 pF, AC couple with up to 400 DCV.4. Additional error to be added as frequency > 30kHz and signal input < 10% of range. 30kHz ~ 100kHz: 0.003% of full scale per kHz.5. For 10 A ranges, the frequency is verified for less than 5 kHz.6. For input < 200V rms.7. For input < 300V rms.Table 3. Frequency Accuracy ± (% of reading + 3 counts)1Notes on Specifications:1. Specifications are for 90 minutes warm-up time, slow mode and calibration temperature within 18 °C - 28 °C.2. The frequency can be measured up to 1 MHz as 0.5 V signal to 100 mV / 1 V ranges.3. 10% of range to full scale input on all ranges except where noted. 100 mV range specifications are for full scale or greater inputs. For inputs from 10 mV to 100 mV, multiply total % of reading error by 10.4. 10% of range to full scale input on all ranges except where noted. 10 mA range specifications are for full scale or greater inputs. For inputs from 1 mA to 10 mA, multiply total % of reading error by 10.Table 4. Frequency resolution1.The frequency can be measured up to 1 MHz as 0.5 V signal to 100 mV / 1 V ranges.Temperature and Capacitance Specifications1Table 5 Temperature and Capacitance Accuracy ± (% of reading + % of range)Notes on Specifications:1. Specifications are for 90 minutes warm-up time, slow mode and calibration temperature within 18 °C - 28 °C.2. 20% over range on all ranges.Operating SpecificationsTable 6. Operating Specifications on single display (approximate)Notes on Specifications:1. Time to change from 2-wire resistance to this specified function and to take at least one reading using SCPI “FUNC” and “READ?” commands.2. Time to change from one range to the next higher range and to take at least one reading using SCPI “FUNC” and “READ?” commands.3. Time to automatically change one range and to take at least one reading using SCPI “CONF AUTO” and “READ?” commands.4. Number of measurements using SCPI “READ?”command when front panel display is off using “DISP OFF” command.5. Reading rate depends on signal frequency > = 20Hz.Supplemental Measurement SpecificationsTable 7 .Supplemental measurement specificationsTable 7 .Supplemental measurement specifications(continued)General Characteristics303.2 mm103.8 mStandard shipped accessories:• Test lead set • Power cord • USB interface cable • Quick Start Guide • Product Reference CD• Agilent IO Library Suite CD-ROMUpgradable Options:• 3445GPBU - GPIB connectivity upgrade• 3445MEMU - 50,000 memory points upgrade for data loggingDimensions1134138A Test Lead Set E2308A Thermistor Temperature Probe34191A 2U Dual Flange Kit34194A Dual Lock Link Kit82350B PCI High-Performance GPIB Interface Card82357B USB/GPIB Interface High-Speed USB 2.010833A/B/C/D/F/G GPIB Cable in various lengths (0.5 m, 1 m, 2 m, 4 m, 0.5 m, 6 m and 8 m)34190A Rackmount KitAgilent Optional Accessories:LAN eXtensions for Instruments puts the power of Ethernet and the Web inside your test systems. Agilent is a founding member of the LXI consor-tium.Agilent XXXXX Partnersw w w /find/xxxxxpartners Get the best of both worlds: Agilent’s measurement expertise and product breadth, combined with channel partner convenience.For more information on Agilent T echnologies’ products, applications or services, please contact your local Agilent office. The com-plete list is available at:/find/contactus Americas Canada (877) 894 4414 Brazil (11) 4197 3600Mexico 01800 5064 800 United States (800) 829 4444Asia Pacific Australia 1 800 629 485China 800 810 0189Hong Kong 800 938 693India 1 800 112 929Japan 0120 (421) 345Korea 080 769 0800Malaysia 1 800 888 848Singapore 180****8100Taiwan 0800 047 866Other AP Countries (65) 375 8100 Europe & Middle East Belgium 32 (0) 2 404 93 40 Denmark 45 45 80 12 15Finland 358 (0) 10 855 2100France 0825 010 700**0.125 €/minuteGermany 49 (0) 7031 464 6333 Ireland 1890 924 204Israel 972-3-9288-504/544Italy39 02 92 60 8484Netherlands 31 (0) 20 547 2111Spain 34 (91) 631 3300Sweden0200-88 22 55United Kingdom 44 (0) 118 927 6201For other unlisted countries:/find/contactusRevised: October 11, 2012Product specifications and descriptions in this document subject to change without notice.© Agilent Technologies, Inc. 2012Published in USA, October 15, 20125991-1133EN/find/34450AAgilent Advantage Services is committed to your success throughout your equip-ment’s lifetime. To keep you competitive, we continually invest in tools andprocesses that speed up calibration and repair and reduce your cost of ownership. You can also use Infoline Web Services to manage equipment and services more effectively. By sharing our measurement and service expertise, we help you create the products that change our world./quality/find/advantageservicesAdvancedTCA ® Extensions for Instrumentation and Test (AXIe) is an open standard that extends the AdvancedTCA for general purpose and semiconductor test. Agilent is a founding member of the AXIe consortium.PCI eXtensions for Instrumentation (PXI) modular instrumentationdelivers a rugged, PC-based high-per-formance measurement and automa-tion system.Quality Management SystemQuality Management Sys ISO 9001:2008DEKRA Certified /find/myagilent A personalized view into the information most relevant to you.myAgilentmy Agilent。

5061-9694AgilentE3640A – E3649A Programmable DC Power SuppliesData SheetReliable Power, Repeatable Results Single and dual outputs Dual range output30 W to 100 W output power Front and rear output terminals Over-voltage protection Remote SensingGPIB and RS-232 standard Save and recall functionsGreat Performance, Outstanding PriceWith the output power of 30 to 100 W, the Agilent E364xA Series programmable DC power supplies provide great performance at a great price. All ten models deliver clean power, excellent regulation, fast transient response and built-in GPIB and RS-232 interfaces. They are designed to meet the needs of R&D design verifi cation, production testing, QA verifi cations, and other demanding applications with AgilentTechnologies’s quality and reliability.Steady OutputWith 0.01 percent load and line regulation, Agilent E364xA power supplies are able to maintain a steady output when power line and load changes occur. They also specify normal mode voltage noise and low common mode current noise. The low normal mode noise specifi cation assures clean power for precision circuitry applications, and the low common mode current provides isolation from power line current injection. Agilent E364xA power supplies specify less than 90 msec of voltage settling time at any output load condition.••••••••Remote InterfaceAgilent E364xA power suppliessupport any PC with a GPIB (IEEE-488) card or RS-232 interface. Every model ships standard with both GPIB and RS-232. The easy-to-use SCPI (Standard Commands forProgrammable Instruments) allow fast and simple programming procedures. Besides, the user manual provides suffi cient information on programming for all end users, from beginners to veterans.Broad Support VXI plug and play software drivers are available for Agilent VEE, National Instruments LabView TMand LabWindows TM . With these drivers, integration of the E364xA into your system can never be any easier. The drivers are supported under Microsoft ®Windows 98® and NT ®.Front Panel OperationAn easy-to-use rotary knob and self-guiding keypads allow you to set theoutput at your desired resolutionwithout any effort. Also, both voltageand current levels can be set to amaximum resolution of 10 mV/1 mAfrom the front panel. In addition, youcan store and recall for up to fi vecomplete power supply setups usingthe internal non-volatile memory.The output on/off button sets the output to zero. If you own a dual output model, you can view twovoltages or currents that are displayed simultaneously.Versatile PowerAgilent E364xA power supplies give you the fl exibility to select from dual output ranges. Output load isprotected against overvoltage, which can be easily monitored and adjusted from the front panel and remoteinterface. Remote sensing is availablein the rear terminal to eliminate errors caused by voltage drops on the load leads. These power supplies offer newversatile binding posts on the front panel and screw-type terminals on the rear panel. New front panel binding posts allow you to use safety testleads as well as conventional banana clips and stripped wires. An optionalrackmount kit is available. The Agilent E364xA Series employs a cooling fan with automatic speed control to reduce the acoustic noise. LabView and LabWindows are registered trademarks of National Instruments.Microsoft Windows 98 and Windows NT are US registered trademerks of Microsoft Corporation.Highly visible vacuumfl ourescent displaySelectable dual rangeprovides fl exibilityand convenienceElectronic calibration from the front panel Rotary knob for quick and analog-like control of voltage and current Tough handle for easy carriage and unitprop-upVersatile binding posts offer fl exibility to use safety test leads, banana plugs or stripped wires1 year warranty protects your investmentBuilt-in GPIB and RS-232 interfaces Cooling fan with automatic speed control for low acoustic noise Rear output and sensing terminalsStore and recall up to fi ve different operating statuses in non- volatile storage locations Set the overvoltage protection and enable the overvoltage protection circuitAgilent E3640A – E3649A Programmable DC Power Supply Specifi cationsModel Number E3640A E3641A E3642A E3643A E3644A E3645A Maximum Power30 W50 W80 W# of Outputs111111DC Output Rating (@ 0 ºC to 40 ºC)0 to 8 V/3 A or0 to 20 V/1.5 A0 to 35 V/0.8 A or0 to 60 V/0.5 A0 to 8 V/5 A or0 to 20 V/2.5 A0 to 35 V/1.4 A or0 to 60 V/0.8 A0 to 8 V/8 A or0 to 20 V/4 A0 to 35 V/2.2 A or0 to 60 V/1.3 ANet Weight 5.3 kg 5.2 kg 6.3 kg 6.2 kg 6.6 kg 6.7 kg Dimensions (without bumper)212.6 mm W x 88.5 mm H x 348.3 mm DModel Number E3646A E3647A E3648A E3649A Maximum Power60 W100 W# of Outputs2222DC Output Rating (@ 0 ºC to 40 ºC)Two0 to 8 V/3 A or0 to 20 V/1.5 ATwo0 to 35 V/0.8 A or0 to 60 V/0.5 ATwo0 to 8 V/5 A or0 to 20 V/2.5 ATwo0 to 35 V/1.4 A or0 to 60 V/0.8 ANet Weight8.2 kg8.0 kg9.2 kg9.1 kg Dimensions (without bumper)212.8 mm W x 133.0 mm H x 348.3 mm DLoad and Line Regulation ± (% of output + offset)Voltage< 0.01% + 3 mVCurrent< 0.01% + 250 µARipple and Noise (20 Hz to 20 MHz)Normal Mode Voltage< 5 mVpp/0.5 mVrms for 8 V/20 V models< 8 mVpp/1 mVrms for 35 V/60 V modelsNormal Mode Current< 4 mArmsCommon Mode Current< 1.5 µArmsAccuracy1 12 Months (@ 25 ºC ± 5 ºC), ± (% output + offset)ProgrammingVoltage< 0.05% + 10 mV (< 0.1% + 25 mV for output 2 of E3646/47/48/49 A)Current< 0.2% + 10 mAReadbackVoltage< 0.05% + 5 mV (< 0.1% + 25 mV for output 2 of E3646/47/48/49 A)Current< 0.15% + 5 mA (< 0.15% + 10 mA for output 2 of E3646/47/48/49 A)ResolutionProgram< 5 mV/1 mAReadback< 2 mV/1 mAMeter10 mV/1 mATransient Response Less than 50 µsec for output to recover to within 15 mV following a change in output current from full load to halfload or vice versa.Settling Time2< 90 msecOVPAccuracy,± (% output + offset) Activation Time3< 0.5% + 0.5 V< 1.5 msec, OVP ≥ 3 V/< 10 msec, OVP < 3 VTemperature Coeffi cient per ºC ± (% output + offset)Voltage< 0.01% + 3 mV (< 0.02% + 5 mV for output 2 of E3646/47/48/49A)Current< 0.02% + 3 mA1 Accuracy specifi cations are valid after a 1-hour warm-up with no load and calibration at 25 ºC.2 Maximum time required for the output voltage to change from 1% to 99% or vice versa following the receipt of VOLT age or APPLy command via direct GPIB or RS-232 interface.3 Average time for output to start and drop after an OVP condition occurred.Stability, constant load & temperature ± (% output + offset), 8 hrsVoltage< 0.02% + 2 mVCurrent< 0.1% + 1 mARemote SensingMax. voltage drop in each load lead1 VAC Input(47 Hz – 63 Hz)100 Vac ± 10% (Opt 0E9)/115 Vac ± 10% (Std)/230 Vac ± 10% (0E3) Warranty 1 yearProduct Regulation Designed to comply with UL3111-1; certifi ed to CSA 22.2 No. 1010.1;conforms to IEC 1010-1; complies with EMC directive 89/336/EEC (Group 1, Class A)Agilent E364xA Series Power Supplies E3640A 30-Watt Single Power Supply E3641A 30-Watt Single Power Supply E3642A 50-Watt Single Power Supply E3643A 50-Watt Single Power Supply E3644A 80-Watt Single Power Supply E3645A 80-Watt Single Power Supply E3646A 60-Watt Dual Power Supply E3647A 60-Watt Dual Power Supply E3648A 100-Watt Dual Power Supply E3649A 100-Watt Dual Power Supply Accessories IncludedUser’s Guide, Quick Reference Guide and AC power cordPower OptionsOpt. 0E3 230 Vac ± 10%Opt. 0EM 1150 Vac ± 10%Opt. 0E9 100 Vac ± 10%Other OptionsOpt. 1CM Rackmount kit*– Single Output (P/N 5063-9240)– Dual Output (P/N 5063-9243) Opt. 0L2 Extra ManualOpt. UK6 Commercial calibration with test result dataE3600A-100 Test lead kit Rackmount Kits*Agilent E3640A/41A/42A/43A/44A/45A To rackmount two instruments side-by-side Lock-link Kit (P/N 5061-9694)Flange Kit (P/N 5063-9212)To rackmount one or two instruments in a sliding support shelfSupport Shelf (P/N 5063-9255)Slide Kit (P/N 1494-0015) required for support shelfFor a single instrument, also orderFilter Panel (P/N 5002-3999)Agilent E3646A/47A/48A/49ATo rackmount two instruments side-by-side Lock-link Kit (P/N 5061-9694)Flange Kit (P/N 5063-9214)To rackmount two instruments in a sliding support shelfSupport Shelf (P/N 5063-9256)Silde Kit (P/N 1494-0015)* Rackmounting with 1CM or lock-link/fl ange kit requiresAgilent or customer support railsAgilent Support Rails-E3663ACRemove all doubtOur repair and calibration services will get yourequipment back to you, performing like new, when promised. You will get full value out of your Agilent equipment throughout its lifetime. Your equipment will be serviced by Agilent-trained technicians using the latest factory calibration procedures, automated repair diagnostics and genuine parts. You will always have the utmost confi dence in your measurements.Agilent offers a wide range of additional expert test and measurement services for your equip-ment, including initial start-up assistance onsite education and training, as well as design, system integration, and project management.For more information on repair and calibration services, go to/find/removealldoubt/fi nd/emailupdatesGet the latest information on the products and applica-tions you select./fi nd/agilentdirectQuickly choose and use your test equipment solutions with confi dence./fi nd/openAgilent Open simplifi es the process of connecting and programming test systems to help engineers design, validate and manufacture electronic products. Agilent offers open connectivity for a broad range of system-ready instruments, open industry software, PC-standard I/O and global support, which are combined to more easily integrate test system development.is the US registered trademark of the LXI Consortium.Agilent Email UpdatesAgilent DirectAgilent OpenFor more information on Agilent Technologies’products, applications or services, please contact your local Agilent office. The complete list is available at:/find/contactus Phone or Fax United States:(tel) 800 829 4444(fax) 800 829 4433Canada:(tel) 877 894 4414(fax) 800 746 4866China:(tel) 800 810 0189(fax) 800 820 2816Europe:(tel) 31 20 547 2111Japan:(tel) (81) 426 56 7832(fax) (81) 426 56 7840Korea:(tel) (080) 769 0800(fax) (080) 769 0900Latin America:(tel) (305) 269 7500Taiwan:(tel) 0800 047 866 (fax) 0800 286 331Other Asia Pacifi c Countries:(tel) (65) 6375 8100 (fax) (65) 6755 0042Email:*****************Revised: 1⅛ /06Product specifi cations and descriptions in this document subject to change without notice.© Agilent Technologies, Inc. 2002-2007Printed in USA, October 26, 20075968-7355EN5061-9694。

Agilent E36XX-Series Manual dc Power SuppliesData Sheet•Linear power supply •Single, dual or triple output •10-turn voltage and current controls •Digital voltage and current meters •Low noise and excellent regulationAffordable, full-featured benchtop power suppliesprovide excellent performance and flexibilityA whole family of low-cost power supplies to meet your needsThe E3600-series of low-cost benchtop power supplies give you the perform-ance of system power supplies without the high price. All E3600family members give you clean power with dependable regulation and fast transient response. E3600-seriessingle-output models are described on this page. See page 2 for information on dual- and triple-output models.Single-output modelsAll E3600-series single-output power supplies feature separate digital-panel meters for monitoring voltage and current simultaneously, giving you precise reading and control capability.All models except the E3630A also feature 10-turn potentiometers for accurate adjustment of voltage and current output settings.With 0.01 percent load and line regulation, these instruments keep the output steady when power line and load changes occur. The low normal-mode noise specification of less than 200µVrms ensures clean power for precision circuitry.In all single-output models, either the positive or negative terminal can be connected to ground, providing a positive or negative voltage output.Outputs can also be floated up to 240V from ground.These instruments also featureadjustable current limits, letting you set the safest current limit without having to short the output.E3610A, E3611A, and E3612A single-output modelsThese popular 30-watt bench supplies are designed for general laboratory use. The constant-voltage, constant-current output allows operation as either a voltage or current source. The changeover occurs automatically,based on the load. Each of thesemodels has two ranges, allowing more current at a lower voltage. For higher output voltages, supplies can be connected in series.Agilent Technologies1981E3614A, E3615A, E3616A and E3617A models feature overvoltage protection These flexible 60-watt, single-range power supplies can be used as either voltage or current sources. When output terminal voltage increases to a preset shut-down level, an overvoltage protection circuit disables the output to protect the device under test (DUT) from damage. The overvoltage protection feature is easily monitored and adjusted from the front panel. Using remote sensing capability, these instruments automatically compensate for voltage drop in the load leads, so you get accurate voltage at the DUT.You can combine multiple units in auto-parallel, auto-series and auto-tracking configurations for greater output voltage or current capacity. Front and rear output terminals allow flexible configuration. Output voltage and current can be controlled with external 0- to10-volt analog voltage or variable resistance.Multi-output modelsWith multiple supplies in a compactunit, the E3620A and E3630A giveyou excellent performance whilesaving space on your bench. Bothinstruments feature tight 0.01 percentline and load regulation and a lownormal-mode noise specification ofless than 0.35mV to ensure cleanpower for precision circuitry. With acommon-mode current specificationof less than 1uA, both multiple-outputpower supplies minimize power linecurrent injection.Like the single-output models in theE3600 series, the E3620A and E3630Afeature separate digital panel metersso you can monitor voltage andcurrent simultaneously. They alsoprotect your DUT against overloadand short-circuit damage. Smoothturn-on and turn-off transitions keeppower spikes out of your circuits.E3620A dual-output power supplyThe 50-watt E3620A dual-outputpower supply provides two 0 V to25 Vdc outputs with the maximumcurrent of 1 A to satisfy most benchrequirements. The outputs arecompletely independent and isolated.E3630A triple-output power supplyThe 35-watt E3630A triple- outputpower supply provides three dcoutputs: 0 to 6 V with a maximumcurrent of 1 to 2.5A and 0 to 20 V and0to -20 V with a maximum current of0.5A. An autotracking feature lets youuse one voltage control to adjust the+20 V and -20 V outputs simultan-eously. The outputs track each otherto within 1 percent, making it easy toadjust the power supply for circuitsrequiring balanced voltages.3-year warrantyTo ensure maximum reliablity andlong life, all 3600-series powersupplies undergo the same rigeroustests as Agilent top-of-the-line powersupplies. Each instrument comes witha full 3-year warranty.23Ordering Information E3600-Series Power Supplies E3610A 30-Watt Power Supply E3611A 30-Watt Power Supply E3612A 30-Watt Power Supply E3614A 48-Watt Power Supply E3615A 60-Watt Power Supply E3616A 60-Watt Power Supply E3617A 60-Watt Power Supply E3620A Dual-output Power Supply E3630A Triple-output Power SupplyAccessories includedOperating and service manuals and AC power cord Power OptionsOpt. 0E3 230 Vac ±10%Opt. 0E9 100 Vac ±10%Other OptionsOpt. W50 Additional 2-year warranty (5-year total)Opt. 1CM Rack-mount kit (E3614A, E3615A,E3616A, E3617A, E3620A)Extra manual sets E3610A/11A/12A Manual (P/N 5959-5304)E3614A/15A/16A /17A Manual (P/N 5959-5310)E3620A Manual (P/N E3620-90001)E3630A Manual (P/N 5959-5329)Rack Mount KitsE3610A/11A/12A/30A (P/N 5063-9767)E3614A/15A/16A/17A/20ATo rack mount instruments side by side Lock-link Kit (P/N 5061-9694)Flange Kit (P/N 5063-9212)To rack mount one or two instruments in a sliding support shelfSupport Shelf (P/N 5063-9255)Slide Kit (P/N 1494-0015)For a single instrument, also order filler panel (P/N 5002-3999)Agilent TechnologiesBy internet, phone, or fax, get assistance with all your test & measurement needs Online assistance:/find/assist Phone or FaxUnited States:(tel)180****4844Canada:(tel)187****4414(fax) (905) 282-6495China:(tel) 800-810-0189(fax) 1-0800-650-0121Europe:(tel) (31 20) 547 2323(fax) (31 20) 547 2390Japan:(tel) (81) 426 56 7832(fax) (81) 426 56 7840Korea:(tel) (82-2) 2004-5004 (fax) (82-2) 2004-5115Latin America:(tel) (305) 269 7500(fax) (305) 269 7599Taiwan:(tel) 080-004-7866 (fax) (886-2) 2545-6723Other Asia Pacific Countries:(tel) (65) 375-8100 (fax) (65) 836-0252Email:*******************Product specifications and descriptions in this document subject to change without notice.© Agilent Technologies, Inc. 2001Printed in USA September 11, 20015968-9727ENAgilent Technologies’ Test and Measurement Support, Services, and AssistanceAgilent Technologies aims to maximize the value you receive, while minimizing your risk and problems. We strive to ensure that you get the test and measurement capabilities you paid for and obtain the support you need. Our extensive support resources and services can help you choose the right Agilent products for your applications and apply them successfully.Every instrument and system we sell has aglobal warranty. Support is available for at least five years beyond the production life of theproduct. Two concepts underlie Agilent’s overall support policy: “Our Promise” and “Your Advantage.”Our PromiseOur Promise means your Agilent test andmeasurement equipment will meet its advertised performance and functionality. When you are choosing new equipment, we will help you with product information, including realistic performance specifications and practical recommendations from experienced test engineers. When you use Agilent equipment, we can verify that it works properly, help with product operation, and provide basic measurement assistance for the use ofspecified capabilities, at no extra cost upon request. Many self-help tools are available.Your AdvantageYour Advantage means that Agilent offers a wide range of additional expert test and measurement services, which you canpurchase according to your unique technical and business needs. Solve problems efficiently and gain a competitive edge by contracting with us for calibration,extra-cost upgrades, out-of-warranty repairs, and on-site education and training, as well as design, system integration, project management,and other professionalengineering services. Experienced Agilent engineers and technicians worldwide can help you maximize your productivity, optimize the return on investment of your Agilent instruments and systems, and obtaindependable measurement accuracy for the life of those products.。

Agilent 4100ExoScan FTIR操作手册声明© Agilent Technologies, Inc. 2009, 2011, 2013, 2017根据美国和国际版权法，未经Agilent Technologies, Inc. 事先许可和书面同意，不得以任何形式或通过任何方法（包括电子存储和检索以及翻译成其他语言）复制本手册的任何部分。

手册部件号0023-401版本2017 年 10 月，第六版马来西亚印刷Agilent Technologies Australia [M] Pty. Ltd.679 Springvale RoadMulgrave, Victoria, Australia 3170 保修本文档所含资料“按原样”提供，在以后的版本中若有更改，恕不另行通知。

此外，在适用的法律所允许的最大范围内，Agilent 对与此手册相关的内容及其中所含的信息不作任何明示或默示的保证，包括但不限于为特定目的的适销性和适用性所作的默示保证。

Agilent 对提供、使用或应用本文档及其包含的任何信息所引起的错误或偶发或必然损坏概不负责。

如果 Agilent与用户之间单独签定的书面协议中所含的保证条款与本文档中的条款冲突，则应以单独协议中的保证条款为准。

技术许可证本文档中描述的硬件或软件是根据许可证提供的，其使用或复制必须符合此类许可证的有关条款。

限制性权利的说明如果软件在美国政府的项目主合同和转包合同中使用，则所交付并许可使用的软件是 DFAR 252.227-7014（1995 年 6 月）中定义的“商用计算机软件”，或 FAR2.101(a) 中定义的“商用品”，或 FAR 52.227-19（1987 年 6 月）或任何同等机构法规或合同条款中定义的“限制性计算机软件”。

本软件的使用、复制或公布受Agilent Technologies 标准商用许可条款的限制，非国防部 (DOD)机构和美国政府机构所受限制以FAR 52.227-19(c)(1-2)（1987 年6 月）中定义的“限制性权利”为准。

About this ManualWe’ve added this manual to the Agilent website in an effort to help you support your product. This manual is the best copy we could find; it may be incomplete or contain dated information. If we find a more recent copy in the future, we will add it to the Agilent website.Support for Your ProductAgilent no longer sells or supports this product. Our service centers may be able to perform calibration if no repair parts are needed, but no other support from Agilent is available. You will find any other available product information on the Agilent Test & Measurement website, .HP References in this ManualThis manual may contain references to HP or Hewlett-Packard. Please note that Hewlett-Packard's former test and measurement, semiconductor products and chemical analysis businesses are now part of Agilent Technologies. We have made no changes to this manual copy. In other documentation, to reduce potential confusion, the only change to product numbers and names has been in the company name prefix: where a product number/name was HP XXXX the current name/number is now Agilent XXXX. For example, model numberHP8648A is now model number Agilent 8648A.s1。

Agilent B2900A 系列精密电源/测量单元技术资料经济型电源/测量解决方案提供出色的性能和一流的图形用户界面●综合的电压/电流4 象限精密电源和测量能力，适用于简单、精确的I/V 测量●高达210 V 的电压，3 A DC/10.5 A 脉冲●10 fA/100 nV 最小测量分辨率(6½ 位)●10 fA/100 nV 最小电源分辨率(6½ 位)●4.3 英寸的前面板彩色显示屏支持图形和数字查看模式●高分辨率的任意波形生成(AWG) 和列表扫描功能(10 µs 最小间隔)●高速数字转换能力( 采样率最高为100000 点/秒)●免费的应用软件有助于实现基于PC 的仪器控制●IVI-COM 驱动程序和用于支持传统SMU 命令集的SCPI 能够实现基本的兼容性●LXI C 类标准、USB2.0、GPIB、LAN 和数字I/O 接口Agilent B2900A 系列精密电源/测量单元是外观紧凑、成本经济的台式电源/测量单元(SMU)，能够同时输出并测量电压和电流。

SMU 在单个仪器中整合了电流源、电压源、电流表、电压表以及在这些功能之间自由切换的能力。

Agilent B2900A 系列SMU 以前所未有的低价格提供一流的性能。

它拥有广泛的电压(210 V) 和电流(3 A 直流和10.5 A 脉冲) 电源能力，卓越的精度( 低至10 fA/100 nV 的电源和测量分辨率) 和高测量吞吐率。

它还支持任意波形生成功能。

此外，Agilent B2900A 系列具备出色的图形用户界面及各种查看模式，可显著改进测试生产率、调试和表征过程。

Agilent B2900 系列SMU 凭借其全面、综合的电源和测量能力，成为测试半导体、有源/无源器件以及各种其他器件与材料的理想选择。

B2900 系列广泛应用在用于工业开发、测试和制造业等领域的研发和教育应用。

它们还可作为独立仪器或系统元器件使用。

Agilent 6680A Series Single-Output, 5000 W DC Power Supplies, GPIB Data SheetReliable DC power for manufacturing test andlong-term burn-inThis series of 5000 watt DC power supplies has the exceptional, proven reliability that test system engineers look for. It also has the features needed for easy test system integration.Programming of the DC output and the extensive protection features can be done either from the front panel or using industry standard SCPI com-mands via the GPIB. Using the serial link, up to 16 power supplies can be connected through one GPIB address. Test system integration can be further simplified by using the VXI plug&play drivers. The output voltage and currentcan also be controlled with analog signals. This is helpful for certain types of noisy environments, and also immediate reactions to process changes.The 6680A series has extremely low ripple and noise for a 5000 watt DC power supply. This helps the built-in measurement system make extremely accurate current and voltage measurements.Selectable compensation is provided for problem-free powering of inductive loads.• Low output ripple and noise• Selectable compensation for inductive loads• Analog control of output voltage and current• Fan-speed control to minimize acoustic noise• Built-in measurements and advanced programmable features • Protection features to ensure DUTsafetySpecifications23Agilent models: 6680A, 6681A, 6682A, 6683A, 6684ATopSupplemental characteristics for all model numbersDC floating voltage: Output terminals can be floated up to ± 60 VDC from chassis groundRemote sensing: Up to half the rated output voltage can be dropped in each load lead. The drop in the load leads subtracts from the voltage available for the load.Command processing time: Average time required for the output voltage to begin to change following receipt of digital data is 20 ms for power supplies connected directly to the GPIB.Modulation: (Analog programming of output voltage and current):Input signal: 0 to –5 V for voltage, 0 to +5 V for currentInput impedance: 30 kΩ or greater AC input (47 to 63 Hz):180 to 235 VAC (line-to-line, 3 phase), 27.7 A rms maximum worst case, 21.4 A rms nominal; 360 to 440 VAC, 14.3 A rms maximum worst case, 10.7 A rms nominal (maximum line current includes 5% unbalanced phase voltage condition.) Output voltage derated 5% at 50 Hz and below 200 VAC Input power: 7350 VA and 6000 W maximum; 160 W at no loadGPIB interface capabilities:SH1, AH1, T6, L4, SR1, RL1, PP0, DC1, DT1, E1, and C0. IEEE-488.2 and SCPI command set.Software driver: • IVI-COM • VXI plug&playSize:425.5 mm W x 221.5 mm H x 674.7 mm D (16.75 in x 8.75 in x 25.56 in)Weight: Net, 51.3 kg (113 lbs); shipping, 63.6 kg (140 lbs)Warranty: One yearAgilent Email Updates/find/emailupdatesGet the latest information on the products and applications you select.Agilent Channel Partnersw w w /find/channelpartners Get the best of both worlds: Agilent’s measurement expertise and product breadth, combined with channel partner convenience.For more information on AgilentTechnologies’ products, applications or services, please contact your local Agilent office. The complete list is available at:/fi nd/contactusAmericas Canada (877) 894 4414Brazil (11) 4197 3600Mexico01800 5064 800United States(800) 829 4444Asia Pacifi cAustralia 1 800 629 485China 800 810 0189Hong Kong 800 938 693India 1 800 112 929Japan 0120 (421) 345Korea 080 769 0800Malaysia 1 800 888 848Singapore 180****8100Taiwan 0800 047 866Other AP Countries (65) 375 8100Europe & Middle East Belgium 32 (0) 2 404 93 40 Denmark 45 45 80 12 15Finland 358 (0) 10 855 2100France 0825 010 700**0.125 €/minuteGermany 49 (0) 7031 464 6333Ireland 1890 924 204Israel 972-3-9288-504/544Italy39 02 92 60 8484Netherlands 31 (0) 20 547 2111Spain 34 (91) 631 3300Sweden0200-88 22 55United Kingdom 44 (0) 118 927 6201For other unlisted countries: /fi nd/contactusRevised: January 6, 2012Product specifications and descriptions in this document subject to change without notice.© Agilent Technologies, Inc. 2012Published in USA, March 14, 20125990-9307EN/find/6680Agilent Advantage Services is committedto your success throughout your equip-ment’s lifetime. To keep you competitive, we continually invest in tools andprocesses that speed up calibration and repair and reduce your cost of ownership. You can also use Infoline Web Services to manage equipment and services more effectively. By sharing our measurement and service expertise, we help you create the products that change our world./quality/find/advantageservicesQuality Management SystemQuality Management Sys ISO 9001:2008DEKRA Certified Ordering informationThe 6680A power supplies come with full documentation on CD-ROM. The CD-ROM includes user’s guide, programming guide, service manual, quick start guide, and application notes.Opt 208 180 to 235 VAC, 3 phase, 47 to 63 HzOpt 400 360 to 440 VAC, 3 phase, 47 to 63 HzOpt 602 Two bus bar spacers for paralleling power supplies (p/n 5060-3514)Opt 0L1 Printed user’s and programming guidesOpt 0B3 Printed service manual Accessories1CM028A* Rack mount flange kit 88.1 mm H (3U) and 132.6 mm H (2U) – 4 brackets (5U total)1CP014A* Double rack mount flange and handle kit 88.1 mm H (2U) and 132.6 mm H (3U)E3663AC Support rails for Agilent rack cabinetsp/n 5080-2148 Serial link cable 2 m (6.6 ft.)p/n 5060-3513 Three 30 A replace-ment fuses for 180 to 235 VAC line p/n 5060-3512 Three 16 A replace-ment fuses for 360 to 440 VAC lineApplication notes6671A/72A/81A/82A/90A System DC Power Supplies Product Overview 5988-3050ENAgilent DC Power Supplies for Base Station Testing , 5988-2386EN 10 Practical Tips You Need to Know About Your Power Products , 5965-8239E* Support rails required。

1．开机
2．关机
3．7890A配置
4．自动调谐及查看真空5．编辑完整的方法6．建立序列及运行序列7．添加图库
8．查看图库及定性9．建立标准曲线10．计算及打印报告11．G CMS原理
12．仪器日常维护
GCMS开机程序
1．打开载气（He）瓶,并把减压阀出口压力调到0.5MPa
2．打开电脑电源,并进入windows操作系统.
3．打开GC电源.再打开MS电源(第一次开机或已放空的情况下,要在推压侧板况态下打开MS电源) 如果是MS部分不漏气的话,分子涡轮泵的速度会很快升上去的.不然就说明是漏气.要关MS再重新再开.
4.双击电脑桌面上的图标.打开GCMS工作站.
5.调出用户户建立的方法:
6. 方法调出后,仪器会进入用户方法所设定的参数状态.待仪器稳定后就可以建立序列,并进行样品检测.。

AgilentE363xA Series Programmable DC Power SuppliesData SheetReliable Power,Repeatable Results• Single and triple output• 80 W to 200 W output power • Dual range output(except E3631A)• Low noise and excellentregulation• Remote sensing(except E3631A)• Front and rear outputterminals(E3633A/34A only)• GPIB and RS-232 standard• Save and recall functions• Overvoltage protection,Overcurrent protection(except E3631A)Clean and stable powerwith programmability at an affordable priceAffordable programmable power supplies to meet your needsThe E363xA Series of programmable DC power supplies gives you the performance of the system power supplies at a decent price. All models provide clean power, excellent regula-tion and a fast transient response with built-in GPIB and RS-232 interfaces. The E363xA Series is designed to meet the requirements of the most demanding applications in R&D design verifi cations, production testing, and QA verifi cations with traditional quality and reliability which you can count on.Excellent performance you can trustWith the 0.01% load and lineregulation, the E363xA Series canmaintain a steady output when powerline and load changes occur. Thepower supplies specify both normalmode voltage/current noise andcommon mode current noise. Thelow normal mode noise specifi cationassures clean power for precisioncircuitry applications, and the lowcommon mode current provides isola-tion from power line current injection.Remote InterfaceIf you have an IEEE-488 card orRS-232 in a PC, these power supplieswill work for you. Every model comesequipped with both GPIB and RS-232as standard. All programming is donein easy-to-use SCPI (Standard Com-mands for Programmable Instruments).The user’s guide describes the processfor the fi rst-time programmers.Front Panel OperationA knob and self-guiding keypads allowyou to set the output at your desiredresolution quickly and easily. Youcan store and recall for up to threecomplete setups using the internalnon-volatile memory. The output on/off button sets the output to zero.E3631A triple-output power supplyThis famous 80-watt triple outputsupply offers three independentoutputs: 0 to 6 V/5A, 0 to +25V/1Aand 0 to –25V/1A. The 6 V output iselectrically isolated from the ±25 Vsupply to minimize any interferencebetween circuits under test. The ±25 Voutputs can be set to track each other.E3632A/33A/34A single-outputdual range power suppliesThese single output power suppliesgive you the fl exibility to select froma dual output range. The output loadis protected against overvoltageand overcurrent, which are easilymonitored and adjusted from the frontpanel and remote interface. Remotesensing is available to eliminate theerrors caused by voltage drops onthe load leads. The E3633A/34A offerfront and rear output terminals foreasy wiring.Model NumberE3631AE3632A E3633A E3634A 123DC OutputRating (0 ºC to 40 ºC)0 to +6 V,0 to 5 A0 to +25 V,0 to 1 A0 to –25 V,0 to 1 A0 to 15 V/7 A or0 to 30 V/4 A0 to 8 V/20 A or0 to 20 V/10 A0 to 25 V/7 A or0 to 50 V/ 4 ALoad Regulation± (% of output + offset)< 0.01% + 2 mV < 0.01% + 250 μALine Regulation± (% of output + offset)< 0.01% + 2 mV < 0.01% + 250 μARipple and Noise (20 Hz to 20 MHz)Normal Mode Voltage< 350 μVrms/2 mVpp< 350 μVrms/3mVpp< 500 μVrms/ 3 mVpp Normal Mode Current< 2 mArms< 500 μArms< 2 mArmsCommon Mode Current< 1.5 μArmsAccuracy1 12 Months (25 ºC + 5 ºC), ± (% output + offset)ProgrammingVoltage0.1% + 5 mV0.05% + 20 mV0.05% + 10 mVCurrent0.2% + 10 mA0.15% + 4 mA0.2% + 10 mAReadback2Voltage0.1% + 5 mV0.05% + 10 mV0.05% + 5 mVCurrent0.2% + 10 mA0.15% + 4 mA0.015% + 5 mAResolutionProgram0.5 mV/0.5 mA 1.5 mV/0.1 mA 1 mV/0.5 mA 1 mV/1 mA 3 mV/0.5 mA Readback0.5 mV/0.5 mA 1.5 mV/0.1 mA0.5 mV/0.1 mA0.5 mV/1 mA 1.5 mV/0.5 mAMeter 1 mV/1 mA10 mV/1 mA 1 mV/1 mA 1 mV/1 mA (< 10A), 10 mA (¡ 10 A) Transient Response Less than 50 μsec for output to recover to within 15 mV following a change in output current from full load to half loador vice versaCommand ProcessingTime3< 50 msec< 100 msecOVP/OCPAccuracy± (% output + offset)N/A0.5% + 0.5 V/0.5% + 0.5 AActivation Time N/A 1.5 msec, OVP ¡ 3 V/< 10 msec, OVP < 3 V and OCP <10 msec Temperature Coeffi cient per ºC (% output + offset)Voltage0.01% + 2 mV0.01% + 3 mVCurrent0.02% + 3 mA0.02% + 0.5 mA0.02% + 3 mAStability, constant load & temperature ± (% of output + offset), 8 hrsVoltage0.03% + 1 mV0.02% + 2 mV0.02% + 1 mVCurrent0.1% + 3 mA0.05% + 1 mA0.1% + 1 mARemote Sense (max.voltage in each load lead)N/A 1 V0.7 VVoltage Programming Speed, to within 1% of total excursionUp Full Load11 msec50 msec50 msec95 msec80 msecNo Load10 msec20 msec20 msec45 msec100 msec Down Full Load13 msec 45 msec45 msec30 msec30 msecNo Load200 msec400 msec400 msec450 msec450 msecE3631A/32A/33A/34A Programmable DC Power Supply Specifi cations1 Accuracy specifi cations are valid after a 1-hour warm-up and calibration at 25 ºC.2 Accuracy refers to readback over GPIB and RS-232 or front panel with respect to actual output.3 Maximum time for output to change after receipt of commands.Ordering Information E3630 Series Power Supplies E3631A 80-WattTriple Power Supply E3632A 120-WattSingle Power Supply E3633A/34A 200-Watt Single Power Supply Standard Shipped Accessories User’s & Service guide, Product Reference CD, AC power cord Power Options Opt. 0E3 230 Vac ± 10%Opt. 0EM 115 Vac ± 10%Opt. 0E9 100 Vac ± 10%Other OptionsOpt. 0L2 Extra manual sets Opt. 1CM Rackmount kit*Opt. UK6 Commercial calibration with test result data E3600A-100 Test lead kitModel Number E3631AE3632A E3633A E3634A123AC Input (47 Hz – 63 Hz)100 Vac ±10% (Opt 0E9)/115 Vac ±10% (Std)/230 Vac ±10% (0E3)Dimensions 213 x mm W x 133 mm H x 348 mm D(8.4 x 5.2 x 13.7 in)Weight 8.2 kg (18 lbs) net, 11 kg (24 lbs) shipping9.5 kg (21 lbs) net, 12 kg (26 lbs) shippingWarranty One year for E363xA series power supplies Three months for standard shipped accessoriesProduct RegulationCertifi ed to CSA 22.2 No. 231 (for E3631A), No. 1010.1 (for E3632A/33A/34A); conforms to IEC 1010-1; carries CE marks; complies with CISPR-11, Group 1, Class ARackmount Kits*Agilent E3631A/32A/33A/34A To rackmount two instruments side-by-sideLock-link Kit (P/N 5061-9694) Flange Kit (P/N 5063-9214)To rackmount one or two instruments in a sliding support shelfSupport Shelf (P/N 5063-9256) Slide Kit (P/N 1494-0015) required for support shelf* Rackmounting with 1CM or lock-link/fl ange kit requiresAgilent or customer support rails Agilent Support Rails-E3663ACLAN eXtensions for Instruments puts the power of Ethernet and the Web inside your test systems. Agilent is a founding member of the LXI consor-tium.Agilent Channel Partnersw w w /find/channelpartners Get the best of both worlds: Agilent’s measurement expertise and product breadth, combined with channel partner convenience.For more information on Agilent Tech-nologies’ products, applications or services, please contact your local Agilent office. The complete list is available at:/fi nd/contactus Americas Canada (877) 894 4414 Brazil (11) 4197 3600Mexico 01800 5064 800 United States (800) 829 4444Asia Pacifi c Australia 1 800 629 485China 800 810 0189Hong Kong 800 938 693India 1 800 112 929Japan 0120 (421) 345Korea 080 769 0800Malaysia 1 800 888 848Singapore 180****8100Taiwan 0800 047 866Other AP Countries (65) 375 8100 Europe & Middle East Belgium 32 (0) 2 404 93 40 Denmark 45 45 80 12 15Finland 358 (0) 10 855 2100France 0825 010 700**0.125 €/minuteGermany 49 (0) 7031 464 6333 Ireland 1890 924 204Israel 972-3-9288-504/544Italy39 02 92 60 8484Netherlands 31 (0) 20 547 2111Spain 34 (91) 631 3300Sweden0200-88 22 55United Kingdom 44 (0) 118 927 6201For other unlisted countries: /fi nd/contactusRevised: October 11, 2012Product specifications and descriptions in this document subject to change without notice.© Agilent Technologies, Inc. 2013Published in USA, January 4, 20135968-9726ENAgilent Advantage Services is committed to your success throughout your equip-ment’s lifetime. To keep you competi-tive, we continually invest in tools and processes that speed up calibration and repair and reduce your cost of ownership. You can also use Infoline Web Services to manage equipment and services more effectively. By sharing our measurement and service expertise, we help you create the products that change our world./quality/find/advantageservicesAdvancedTCA ® Extensions for Instrumentation and Test (AXIe) is an open standard that extends the AdvancedTCA for general purpose and semiconductor test. Agilent is a founding member of the AXIe consortium.PCI eXtensions for Instrumentation (PXI) modular instrumentationdelivers a rugged, PC-based high-per-formance measurement and automa-tion system.Quality Management SystemQuality Management Sys ISO 9001:2008DEKRA Certified /find/myagilent A personalized view into the information most relevant to you.myAgilentmy Agilent。

Agilent8960操作指导书1.目的规范测试员能熟练掌握仪器的使用操作步骤。

2.适用范围适用于公司各类产品的射频传导和天线耦合测试工作。

3.相关文件无4.所需设备、工具、材料Agilent-设备型号：8960-E5515C。

5.过程5.1.准备工作：1.检查电源是否正常通电。

2.是否能正常开机。

3.每天试验前根据《实验室仪器点检表》进行操作点检确认。

5.2.操作步骤：一、对于GSM/GPRS制式的手机，常需要测量的参数有：✓发射功率✓功率时间模板✓相位误差&频率误差✓开关谱&调制谱✓参考灵敏度电平1.打开电源开关，仪器面板如下图所示（见图一)；2.线损设置：按SYSTEM CONFIG，弹出如下界面。

按RF IN/OUT Amptd Offset 。

按F5, RF IN/OUT Amptd Offset Setup。

输入要设置的频率及对应的线损，对于与处于Off状态的项目，我们按On键即可开启。

（详细步骤见8960原理及使用方法介绍）。

3.建立连接：按SYSTEM CONFIG，打开如下界面。

按 Format Switch,选择要切换的制式，在这里我们选择GSM/GPRS。

在Operating Mode里选择 Active Cell (GSM),按Original Call，当屏幕下方显示Connected的时候，表示连接已成功。

在屏幕右侧TrafficBand中选择需要的频段，在Traffic Channel中选择需要的信道。

在手机与8960已连接的情况下，按Measurement selection,选择 Transmit Power,进入测试界面。

按确定可以看到测试结果（详细过程见8960原理及使用方法介绍）。

4. 发射功率：在手机与8960已连接的情况下，按Measurement selection,选择Transmit Power,进入测试界面。

按确定可以看到测试结果（详细过程见8960原理及使用方法介绍）。

ErrataTitle & Document Type: 6826A and 6827A Bipolar Power Supply / Amplifier Operating and Service ManualManual Part Number: 05950-1702Revision Date: January 1974About this ManualWe’ve added this manual to the Agilent website in an effort to help you support your product. This manual provides the best information we could find. It may be incompleteor contain dated information, and the scan quality may not be ideal. If we find a bettercopy in the future, we will add it to the Agilent website.HP References in this ManualThis manual may contain references to HP or Hewlett-Packard. Please note that Hewlett- Packard's former test and measurement, life sciences, and chemical analysisbusinesses are now part of Agilent Technologies. The HP XXXX referred to in this document is now the Agilent XXXX. For example, model number HP8648A is now model number Agilent 8648A. We have made no changes to this manual copy.Support for Your ProductAgilent no longer sells or supports this product. You will find any other availableproduct information on the Agilent Test & Measurement website:Search for the model number of this product, and the resulting product page will guideyou to any available information. Our service centers may be able to perform calibrationif no repair parts are needed, but no other support from Agilent is available.。