地理信息系统上课笔记
- 格式:docx
- 大小:767.35 KB
- 文档页数:7
地理信息系统实验笔记
一、空间分析(Selection)
1、按属性进行查询(select by Attributes)
2、按空间进行查询(select by location)
二、缓冲区
buffer[tools-->Customise-->Commands--->(自己输入buffer)-->(在Categorie中选Tools(wizard)
(1)下一步
1、At a specified distance固定距离缓冲区
<1>数值
<2>单位----->(Buffer distance中选择)
2、based on a distance from an attribute 可变距离缓冲区------->单位(上同)
3、as multiple buffer rings 多环距离缓冲区
<1>number of (环的个数)
<2>distance between (间距数值)
(2)下一步
1、dissolve barriers between( 合并)
3、where do you want the buffer to be saved?(输出的结果存在哪?)
<1>as graphics layer in data frame 缓冲区只用于显示,不用于其他用途
<2>
<3>in a new layer. Specify output shapefile or feature存储于某文
件夹中形成shapefile文件
Analysis Tools ------>proximity---->buffer(另一中buffer的打开方式)
三、overlay(叠加)
Analysis Tools ------> overlay----->union(并集)
DEM:
(1)Grid
<1>加载Grid
<2>Grid符号化
打开属性---->选symbology--->stretched(拉伸)/classified(分类)/unique values(栅格化)
<3>工具栏
1、3D Analyst
2、Spatial Analyst
在Tools工具栏中点extensions(扩展模块)
<4>surface Analysis曲面分析
1、contour等高线
1.1 Input surface (输入的表面):DEM
1.2 contour Interval (等高线间距):20
1.3 (基础等高线)
2、 Slope 坡度
{注:(option)
(1)working 打开文件图标选定要存放的位置
(2)cell size 选定栅格的大小}
2.1 output measurement
1.1 Degree 度 Percent 百分比
1.2 output raster输出栅格
找坡度大于等于25度的地方
先打开spatial Analyst----->Raster Calculator(计算适量数据)
1.3 Aspect 坡向
<4>Hillshade 山体阴影
1、Azimuth :方位角
2、Altitude :高度角
3、Cut/fill :填充
4、Prefile
5、Curvature 剖面曲率
6、Viewshed 可视区
7、插值点
地形起伏度
Spatial Analyst-------->Neighborhood
一、填充DEM(Fill)
Arc ToolBox---->spatial Analyst Tools-------->Hillshade(水文分析) 输入
输出(该名称)
二、水流流向
Flow Direction
输入:Fill DEM
输出:FlowDir
三、汇流累积量
Flow Accumulation------>类型(inteager)
四、提取河网
Reclasify(重分类)
Input FlowACC
Classify:
五、盆地
Basinl
六,河道连接点
Stream Link
七、集水区
Watershed
反距离加权
1.Spatial anlast tools—— interpolation——IDW
2.单击Z value field下拉框箭头选择OZONE
3.单击output cell size改为2000
3.单击environments选择general settings,单击extent下拉箭头选择same as layer ca_outline
4.单击general settings对话框的OK,单击IDW对话框的OK。
如图显示
5.将ca_outline图层的颜色设置为透明色,单击hollow,单击OK。
6.单击Spatial anlast tools—— interpolation——Extraction——双击Extract by mask,单击input raster下拉箭头选择
Idw_ca_ozone3,单击input raster or feature mask by date下
拉箭头选择ca_outline,单击OK。
7.为使图层好看,选择Extract_ IDW_2修改颜色。
关闭Extract_
ozone_3图层。