压铸常用英文词汇V5

铸造英语专用词汇大全材料科学与工程点击上方「材料科学与工程」快速关注材料类综合、全面、专业的微信平台1.基本术语铸造 foundry, founding, casting铸造工艺 foundry technology铸件 casting砂型铸造 sand casting process特种铸造 special casting process2. 合金性能流动性 fluidity充型能力 mold-filling capacity吸气 gas absorption过冷 undercooling supercooling过冷度 degree of undercooling成核 nucleation自发成核（均质成核） homogeneous nucleation非自发成核（非均质成核）heterogeneous nucleation凝固温度范围 solidification range定向凝固（顺序凝固） directional solidification液态收缩（液体收缩） liquid contraction凝固收缩 solidification contraction固态收缩（固体收缩） solid contraction凝固时间 solidification time自由收缩 free contraction受阻收缩 hindered contraction铸件线收缩率 shrinkage收缩应力 contraction stress热应力 thermal stress相变应力 transformation stress,phase change stress 铸造应力 casting stress残留应力（残余应力） residual stress3. 铸造用材料3.1. 金属原材料金属原材料 metallic raw material生铁 pig iron铁合金 ferro-alloy回炉料 foundry returns中间合金 master alloy3.2. 燃料铸造焦炭 foundry coke冶金焦炭 metallurgical coke固定碳 fixed carbon3.3. 熔剂熔剂 flux除气熔剂（除气剂） degassing flux覆盖熔剂（覆盖剂） covering flux精炼熔剂（精炼剂） refining flux耐火度（耐火性） refractoriness耐火砖 firebrick耐火粘土 fireclay硅砖 silica brick镁砂 grain magnesite3.4. 造型材料造型材料 molding material砂 sand水洗砂 washed-out sand硅砂 silica sand天然砂 natural sand人工砂 artificial sand天然粘土砂 naturally clay-bonded sand 橄榄石砂 olivine sand铬铁矿砂 chromite sand锆砂 zircon sand炭粒砂 carbon sand精硅砂 sharp sand红砂 red sand熟料砂 chamotte sand粘结剂 binder粘土 clay无机粘结剂 inorganic binder有机粘结剂 organic binder高岭土 kaolin膨润土 bentonite钠基膨润土 sodium bentonite钙基膨润土 calcium bentonite活化膨润土 activated bentonite干性油 drying oil硬粘结剂(冷硬粘结剂) no bake binder热固树脂粘结剂 thermosetting resin binder油类粘结剂 oil based binder水玻璃粘结剂 water glass binder, sodium silicate binder 纸浆废液 lignin liquor合脂粘结剂 synthetic fat binder水玻璃模数 sodium silicate modulus3.5. 辅助材料附加物 additives发热剂 exothermic mixture分型剂（脱模剂） parting agent,stripping agent固化剂（硬化剂）hardener悬浮剂suspending agent涂料 coating型砂制备（砂处理） sand preparation混砂 sand mulling, sand mixing型砂（造型混合料） molding sand芯砂（造芯混合料） core sand合成砂 synthetic sand自硬砂 self-hardening sand水玻璃砂 sodium silicate-bonded sand覆膜砂 precoated sand烂砂泥（麻泥） loam调匀砂 temper sand面砂 facing sand背砂（填充砂） backing sand单一砂 unit sand含泥量 clay content含水量 moisture content旧砂 floor sand枯砂（焦砂） burnt sand废砂 waste sand热砂 hot sand松砂 aeration , sand-cutting筛分（筛析） screen analysis旧砂处理 sand reconditioning旧砂再生 sand reclamation沉降分选 elutriation, decantation型砂性能及试验型砂试验 sand testing透气性 permeability流动性 flowability型砂强度 sand strength湿强度 green strength干强度 dry strength耐用性（复用性） durability砂型（芯）硬度 mold hardness热变形 hot deformation残留强度 retained strength热强度 hot strength韧性 toughness发气率（发气速度） gas evolution rate 发气性（发气量） gas evolution吸湿性 moisture absorption落砂性 knock-out capability潰散性 collapsibility胶质价 colloid index破碎指数 shatter index热气流烘砂装置 hot pneumatic tube drier混砂机 sand muller, sand mixer松砂机 aerator, sand cutter冷却提升机 cooling elevator, coolevator筛砂机 riddle磁力滚筒 magnetic separator旧砂再生设备 sand reclamation气力输送装置 pneumatic tube conveyor4. 铸造合金4.1. 铸铁铸铁 cast iron铸铁石墨形态 morphology of graphite in cast iron灰铸铁（灰口铸铁） gray cast iron白口铸铁 white cast iron麻口铸铁 mottled cast iron共晶度 degree of saturation碳当量 carbon equivalent初生石墨 primary graphite孕育铸铁 inoculated cast iron球墨铸铁 spheroidal graphite cast iron, nodular graphiteiron, ductile iron球状石墨 spheroidal graphite, nodular graphite可锻铸铁 malleable cast iron黑心可锻铸铁 black heart malleable cast iron珠光体可锻铸铁 pearlitic malleable cast iron铁素体可锻铸铁 ferritic malleable cast iron白心可锻铸铁 white heart malleable cast iron团絮石墨 tempered graphite冷硬铸铁（激冷铸铁） chilled iron耐磨铸铁 wear resisting cast iron耐热铸铁 heat resisting cast iron耐酸铸铁 acid resisting cast iron高硅铸铁 high silicon cast iron蠕墨铸铁 vermicular cast iron,compacted graphite cast iron 蠕虫状石墨 vermicular graphite合金铸铁 alloy cast iron4.2. 铸钢铸钢 cast steel炭素铸钢 carbon cast iron低合金铸钢 low alloy cast steel高锰钢 high manganese steel铁素体钢 ferritic steel铸造非铁合金青铜 bronze铅青铜 lead bronze铝青铜 aluminum bronze黄铜 brass铝铜合金 aluminum-copper alloy铝镁合金 aluminum-magnesium alloy铝硅合金 aluminum-silicon alloy镁合金 magnesium alloy轴承合金（减摩合金） bearing metal, antifrictional metal巴氏合金 babbitt alloy钛合金 titanium alloy5. 熔炼工艺及设备5.1. 熔炼基本术语熔化（熔炼） melting重熔 remelting炉料 charge熔化率 melting rate炉料计算 charge calculation双联熔炼 duplexing元素烧损（元素烧损率）melting losses of various chemical elements熔炼损耗（烧损） total melting loss还原气氛 reducing atmosphere氧化气氛 oxidizing atmosphere惰性气体 inert gas碱度（碱性指数） index of basicity碱性渣 basic slag酸性渣 acid slag精炼 refining遗传性 heredity风口比 tuyere ratio有效高度 effective height送风强度 blast intensity预热送风 hot blast底焦 coke bed层焦 coke split隔焦（结力焦） buffer coke charge炉衬 furnace lining碱性炉衬 basic lining酸性炉衬 acid lining棚料 bridging熔池 bath吸碳 carbon pick-up铁焦比（焦比） iron-coke ratio出渣 deslagging打炉 cupola drop5.2. 铸钢氧化熔炼法 oxidizing melting不氧化熔炼法 dead melting真空熔炼 vacuum refining电渣熔炼 electro-slag melting熔渣 slag沉渣 sludge浮渣 dross, cinder氧化期（沸腾期） oxidizing stage,boil 还原期 deoxidizing stage,blocking stage 还原渣 reducing slag氧化渣 oxidizing slag白渣 white slag脱氧 deoxidation扒渣 slagging- off脱碳 decarburization脱硫 desulphurization脱磷 dephosphorization增碳 recarburizing脱氧剂 deoxidizer挥发损耗 volatilizing losses静置 stewing, holding吹氮 nitrogen flushing5.3. 熔炼设备冲天炉 cupola水冷冲天炉 water-cooled cupola热风冲天炉 hot-blast cupola湿法除尘器 wet cap炉缸 cupola well前炉 forehearth冲天炉加料机 cupola charging machine爬式加料机 skip hoist电磁配铁称 electro-magnetic weighing balancer电磁盘 electromagnetic chuck电弧炉（直接电弧炉） arc furnace,direct arc furnace 感应电炉 electric induction furnace电渣炉 electroslag furnace电磁搅拌electromagnetic agitation浇包 ladle摇包 shaking ladle底注包 bottom pouring ladle保温炉holding furnace坩埚炉crucible furnace孕育 inoculation多孔塞法 porous plug process变质 modification墨化剂 graphitizer过热 superheating石墨球化处理 nodularizing treatment of graphite碳当量仪eutectometer三角试块 wedge test-piece真空除气vacuum degassing5.4. 浇注浇注 pouring保护气氛浇注 pouring under controlled atmosphere 浇注速度 pouring rate浇注温度 pouring temperature浇注时间 pouring time浇注位置 pouring position型内孕育 inmold inoculation压铁 weight捣冒口 churning, pumping点冒口（补注） teeming浸入式高温计 immersion pyremeter补炉 patching炉龄（炉衬寿命） campaign文章来源：粉末冶金圈今日编辑：麦片点击阅读原文，加入交流群。

GLOSSARYAabrasive grinding 强力磨削abrasive[☜'breisiv] a.磨料的, 研磨的absence ['✌bs☜ns] n.. 不在，缺席accesssory[✌k'ses☜ri] n.附件accommodate[☜'k m☜deit] v. 适应accordingly[☜'k :di☠li] adv.因此,从而,相应地accuracy['✌kjur☜si] n精度,准确性actuate['✌ktjueit] vt.开动(机器), 驱动adequate['✌dikwit] a. 足够的adhesive[☜d'hi:siv] n. 粘合剂adjacent[☜'d✞eisnt] a. 邻近的adopt[☜'d pt] vt. 采用advance [☜d'v✌:ns] n.进步advisable [☜d'vaizbl] adj. 可取的agitate['✌d✞iteit] v. 摇动a large extent 很大程度algorithm ['✌l♈☜ri❆☜m] n. 算法align [☜'lain] v 定位，调准alignment[☜'lainm☜nt] n. 校直all-too-frequent 频繁allowance[☜'l☜uens] n. 容差, 余量alternate[' :lt☜nit]v.交替,轮流alternative[ :l't☜:n☜tiv] n. 替换物alternatively[ :l't☜:n☜tivli] ad. 做为选择, 也许aluminiun[ ✌lju'minj☜m] n.铝ample['✌mpl] adj. 充足的analysis [☜'n✌l☜sis] n. 分析ancillary['✌nsil☜ri] a.补助的, 副的angular ['✌♈jul☜] adj. 有角的annealing[☜'li:li☠] n.退火aperture ['✌p☜t☞☜] n.孔applied loads 作用力appropriate [☜'pr☜uprieit] a. 适当的arc[a:k] n.弧, 弓形arise[☜'raiz] vi. 出现, 发生arrange[☜'reid✞] v. 安排article['a:tikl] n.制品, 产品ascertain[ ✌s☜'tein] vt. 确定, 查明assemble[☜'sembl] vt.组装attitude ['✌titju:d] n 态度auxiliary [ :♈'zilj☜ri]adj. 辅助的avoid[☜'v id] v.避免axis['✌ksis] n.轴axle['✌ksl] n.轮轴, 车轴Bbackup['b✌k ✈p] n. 备份batch [b✌t☞] n 一批bearing['b☪☜ri☠] n.轴承,支座bed[bed] n. 床身behavior[bi'heivj☜] n. 性能bench-work 钳工工作bend[bend] v.弯曲beneath[bi'ni: ] prep在···下bin [bin] n. 仓，料架blank [bl✌☠k] n. 坯料blank [bl✌☠k] v. 冲裁,落料blanking tool 落料模blast [bl✈st] n.一阵（风）blemish['blemi☞] n. 缺点, 污点bolster['b☜ulst☜] n. 模座,垫板boost[bu:st] n. 推进boring['b :ri☠] n.镗削, 镗孔bracket ['br✌kit] n. 支架brass [br✌s] n.黄铜break down 破坏breakage ['breikid✞] n.破坏bridge piecebrine[brain] n. 盐水brittle['britl] adv.易碎的buffer [b✈f☜] n.缓冲器built-in 内装的bulging [b✈ld✞i☠] n. 凸肚burr [b☜:] n. 毛刺bush [bu☞] n. 衬套bush[bu☞]n. 衬套by far (修饰比较级, 最高级)···得多, 最by means of 借助于Ccabinet ['k✌binit] n.橱柜call upon 要求carbide['ka:baid] n.碳化物carburzing['ka:bjureti☠] n. 渗碳carriage['k✌rid✞] n.拖板, 大拖板carry along 一起带走carry down over 从···上取下carry out 完成case hardening 表面硬化case[keis] n. 壳, 套cast steel 铸钢casting['ka:sti☠] n. 铸造,铸件category['k✌t☜♈☜uri] n. 种类caution ['k :☞☜n] n. 警告，警示cavity and core plates 凹模和凸模板cavity['k✌viti] n.型腔, 腔, 洞centre-drilling 中心孔ceramic[si'r✌mik] n.陶瓷制品chain doted line 点划线channel['t☞✌nl] n.通道, 信道characteristic[k✌r☜kt☜'ristik] n.特性check[t☞ek] v.核算chip[t☞ip] n.切屑, 铁屑chuck [t☞✈k] n.卡盘chute [☞u:t] n. 斜道circa ['s☜k☜:] adv. 大约circlip['s☜:klip] n.(开口)簧环circuit['s☜:kit] n. 回路, 环路circular supoport block circulate['s☜:kjuleid] v.(使)循环clamp [kl✌mp] vt 夹紧clamp[kl✌mp] n.压板clay[klei] n. 泥土clearance ['kli☜r☜ns] n. 间隙clip [klip] vt. 切断，夹住cold hobbing 冷挤压cold slug well 冷料井collapse[k☜'l✌ps] vi.崩塌, 瓦解collapsible[k☜'l✌ps☜bl] adj.可分解的combination [k mbi'nei☞☜n] n. 组合commence[k☜'mens] v. 开始, 着手commence[k☜'mens]v. 开始commercial [k☜'m☜:☞☜l] adj. 商业的competitive[k☜m'petitiv] a. 竞争的complementary[ k mpli'ment☜ri] a.互补的complexity [kem'pleksiti] n.复杂性complicated['k mpl☜keitid] adj.复杂的complication [k mpli'kei☞☜n] n. 复杂化compression [k☜m'pre☞☜n] n.压缩comprise[k☜m'prais] vt.包含compromise['k mpr☜maiz] n. 妥协, 折衷concern with 关于concise[k☜n'sais] a. 简明的, 简练的confront[k☜n'fr✈nt] vt. 使面临connector[k☜'nekt☜] n. 连接口, 接头consequent['k nsikw☜nt] a. 随之发生的, 必然的console ['k nsoul] n.控制台consume [k☜n'sjum] vt. 消耗, 占用consummate [k☜n's✈meit] vt. 使完善container[k☜n'tein☜] n. 容器contingent[ken'tind✞☜nt] a.可能发生的contour['k☜ntu☜] n.轮廓conventional[k☜n'ven☞☜nl] a. 常规的converge[k☜n'v☜:d✞] v.集中于一点conversant[k n'v☜:s☜nt] a. 熟悉的conversion[k☜n'v☜:☞☜n] n 换算, 转换conveyer[ken'vei☜] n. 运送装置coolant['ku:l☜nt] n. 冷却液coordinate [k☜u' :dnit] vt. (使)协调copy machine 仿形(加工)机床core[k :] n. 型芯, 核心corresponding [ka:ri'sp di☠] n.相应的counteract [kaunt☜'r✌kt] vt. 反作用,抵抗couple with 伴随CPU (central processing unit) 中央处理器crack[kr✌k ] v.（使）破裂，裂纹critical['kritikl] adj.临界的cross-hatching 剖面线cross-section drawn 剖面图CRT (cathoder-ray tube) 阴极射线管crush[kr✈☞]vt.压碎cryogenic[ krai☜'d✞enik ]a.低温学的crystal['kristl] adj.结晶状的cubic['kju:bik] a. 立方的, 立方体的cup [k✈p] vt (使)成杯状, 引伸curable ['kjur☜bl] adj. 可矫正的curvature['k☜:v☜t☞☜] n.弧线curve [k☜:v] vt. 使弯曲cutter bit 刀头, 刀片cyanide['sai☜naid] n.氰化物Ddash [d✌☞] n. 破折号daylight ['deilait] n. 板距decline[di'klain] v.下落,下降,减少,deform[di'f :m] v. (使)变形demonstrate['dem☜streit ] v证明depict[di'pikt ] vt 描述deposite [di'p zit] vt. 放置depression[di'pre☞☜n] n. 凹穴descend [di'sent] v. 下降desirable[di'zair☜bl] a. 合适的detail ['diteil] n.细节，详情deterioration[diti☜ri:☜'rei☞☜n] n. 退化, 恶化determine[di't☜:min] v.决定diagrammmatic[ dai☜gr☜'m✌tik].a.图解的，图表的dictate['dikteit] v. 支配die[dai] n.模具, 冲模, 凹模dielectric[daii'lektrik] n. 电介质die-set 模架digital ['did✞itl ] n.数字式数字, a.数字的dimensional[dddi'men☞☜nl] a. 尺寸的, 空间的discharge[dis't☞a:d✞] n.v. 放电, 卸下, 排出discharge[dis't☞a:d✞] v.卸下discrete [dis'cri:t] adj. 离散的,分立的dislodge[dis'l d✞] v. 拉出, 取出 L12 dissolution[dis☜'lu:☞☜n] n.结束distinct [dis'ti☠kt] a.不同的，显著的distort [dis'd :t] vt. 扭曲distort[dis't :t] vt. (使)变形, 扭曲distributed system 分布式系统dowel ['dau☜l] n. 销子dramaticlly [dr☜'m✌tikli] adv. 显著地drastic ['dr✌stik] a.激烈的draughting[dra:fti☠] n. 绘图draughtsman['dr✌ftsm☜n] n. 起草人drawing['dr :i☠] n. 制图drill press 钻床drum [dr✈m] n.鼓轮dual ['dju:☜l] adv. 双的，双重的ductility [d✈k'tiliti ] n.延展性dynamic [dai'n✌mik ] adj 动力的Eedge [ed✞] n .边缘e.g.(exempli gratia) [拉] 例如ejector [i'd✞ekt☜] n.排出器，ejector plate 顶出板ejector rob 顶杆elasticity[il✌'stisiti] n.弹性electric dicharge machining 电火花加工electrical discharge machining电火花加工electrochemical machining 电化学加工electrode[i'lektr☜ud] n. 电极electro-deposition 电铸elementary [el☜'ment☜ri] adj.基本的eliminate[i'limineit] vt. 消除, 除去elongate[i'l ☠♈et] vt. (使)伸长, 延长emerge [i'm☜:d✞] vi. 形成, 显现emphasise['emf☜saiz] vt. 强调endeavour[en'dev☜] n. 尽力engagement[in'♈eid✞ment] n. 约束, 接合enhance[in'h✌ns] vt. 提高, 增强ensure [in'☞u☜] vt. 确保，保证envisage[in'vizid✞] vt.设想erase[i'reis] vt. 抹去, 擦掉evaluation[i'v✌lju ei☞☜n] n. 评价, 估价eventually[i'v☜nt☞u☜li ] adv.终于evolution[ev☜'lu:☞☜n] n.进展excecution[eksi'kju:☞☜n] n. 执行, 完成execute ['ekskju:t] v. 执行exerte [i♈'z☜:t] vt. 施加experience[iks'piri☜ns] n. 经验explosive[iks'pl☜usiv]adj.爆炸(性)的extend[eks'tend] v. 伸展external[eks't☜:nl] a. 外部的extract[eks'tr✌kt] v. 拔出extreme[iks'tri:m] n. 极端extremely[iks'tri:mli] adv. 非常地extremity[iks'tmiti] n. 极端extrusion[eks'tru:✞☜n] n. 挤压, 挤出FF (Fahrenheit)['f✌r☜nhait] n.华氏温度fabricate ['f✌brikeit] vt.制作,制造facilitate [f☜'siliteit] vt. 帮助facility[f☜'siliti] n. 设备facing[feisi☠] n. 端面车削fall within 属于, 适合于fan[f✌n] n.风扇far from 毫不, 一点不, 远非fatigue[f☜'ti♈] n.疲劳feasible ['fi:z☜bl] a 可行的feature ['fi:t☞☜] n.特色, 特征feed[fi:d] n.. 进给feedback ['fi:db✌k] n. 反馈female['fi:meil] a. 阴的, 凹形的ferrule['fer☜l] n. 套管file system 文件系统fitter['fit☜] n.装配工, 钳工fix[fiks] vt. 使固定, 安装, vi. 固定fixed half and moving half 定模和动模flat-panel technology 平面(显示)技术flexibility[fleksi'biliti] n. 适应性, 柔性flexible['fleks☜bl] a. 柔韧的flow mark 流动斑点follow-on tool 连续模foregoing ['f :'♈☜ui☠]adj. 在前的,前面的foretell[f :'tell] vt. 预测, 预示, 预言forge[f :d✞] n. v. 锻造forming[f :mi☠] n. 成型four screen quadrants 四屏幕象限fracture['fr✌kt☞☜] n.破裂free from 免于Ggap[♈✌p] n. 裂口, 间隙gearbox['♈i☜b ks] n.齿轮箱general arrangementgovern['♈✈v☜n] v.统治, 支配, 管理grain [♈rein] n. 纹理graphic ['♈r✌fik] adj. 图解的grasp [♈r✌sp] vt. 抓住grid[♈rid] n. 格子, 网格grind[♈raind] v. 磨, 磨削, 研磨grinding ['♈raindi☠] n. 磨光,磨削grinding machine 磨床gripper[♈rip☜] n. 抓爪, 夹具groove[♈ru:v] n. 凹槽guide bush 导套guide pillar 导柱guide pillars and bushes 导柱和导套Hhandset['h✌ndset] n. 电话听筒hardness['ha:dnis] n.硬度hardware ['ha:dw☪☜] n. 硬件headstock['hedst k] n.床头箱, 主轴箱hexagonal[hek's✌♈☜nl] a. 六角形的, 六角的hindrance['hindr☜ns] n.障碍, 障碍物hob[h b] n. 滚刀, 冲头hollow-ware 空心件horizontal[h ri'z ntl] a. 水平的hose[h☜uz] n. 软管, 水管hyperbolic [haip☜'b lik] adj.双曲线的Ii.e. (id est) [拉] 也就是identical[ai'dentikl] a同样的identify [ai'dentifai] v. 确定, 识别idle ['aidl] adj.空闲的immediately[i'mi:dj☜tli] adv. 正好, 恰好impact['imp✌kt] n.冲击impart [im'pa:t] v.给予implement ['implim☜nt] vt 实现impossibility[imp s☜'biliti] n.不可能impression[im'pre☞☜n] n. 型腔in contact with 接触in terms of 依据inasmuch (as)[in☜z'm✈t☞] conj.因为, 由于inch-to-metric conversions 英公制转换inclinable [in'klain☜bl] adj. 可倾斜的inclusion [in'klu☞☜n] n. 内含物inconspicuous[ink☜n'spikju☜s] a. 不显眼的incorporate [in'k :p☜reit] v 合并,混合indentation[ inden'tei☞☜n ] n.压痕indenter[in'dent☜] n. 压头independently[indi'pein☜ntli] a. 独自地, 独立地inevitably[in'evit☜bli] ad. 不可避免地inexpensive[inik'spensiv]adj. 便宜的inherently [in'hi☜r☜ntli] adv.固有的injection mould 注塑模injection[in'd✞ek☞☜n] n. 注射in-line-of-draw 直接脱模insert[in's☜:t] n. 嵌件inserted die 嵌入式凹模inspection[in'spek☞☜n] n.检查,监督installation[inst☜'lei☞☜n] n. 安装integration [inti'♈rei☞☜n] n.集成intelligent[in'telid✞☜nt]a. 智能的intentinonally [in'ten☞☜n☜li] adv 加强地，集中地interface ['int☜feis] n.. 界面internal[in't☜:nl] a. 内部的interpolation [int☜p☜'lei☞☜n] n.插值法investment casting 熔模铸造irregular [i'regjul☜] adj. 不规则的，无规律irrespective of 不论, 不管irrespective[iri'spektiv] a. 不顾的, 不考虑的issue ['isju] vt. 发布，发出Jjoint line 结合线Kkerosene['ker☜si:n] n.煤油keyboard ['ki:b :d ] n. 健盘knock [n k] v 敲，敲打Llance [la:ns] v. 切缝lathe[lei❆] n. 车床latitude ['l✌titju:d] n. 自由lay out 布置limitation[limi'tei☞☜n] n.限度,限制,局限(性)local intelligence局部智能locate [l☜u'keit] vt. 定位logic ['l d✞ik] n. 逻辑longitudinal['l nd✞☜'tju:dinl] a. 纵向的longitudinally['l nd✞☜'tju:dinl] a. 纵向的look upon 视作, 看待lubrication[lju:bri'kei☞☜n ] n.润滑Mmachine shop 车间machine table 工作台machining[m☜'☞i:ni☠] n. 加工made-to-measure 定做maintenance['meintin☜ns] n.维护,维修majority[m☜'d✞a:riti] n.多数make use of 利用male[meil] a. 阳的, 凸形的malfunction['m✌l'f✈☠☞☜n] n. 故障mandrel['m✌dtil] n.心轴manifestation[m✌nif☜s'tei☞☜n] n. 表现, 显示massiveness ['m✌sivnis ] 厚实，大块measure['me✞☜] n. 大小, 度量microcomputer 微型计算机microns['maikr n] n.微米microprocessor 微处理器mild steel 低碳钢milling machine 铣床mineral['min☜r☜l] n.矿物, 矿产minimise['minimaiz] v.把···减到最少, 最小化minute['minit] a.微小的mirror image 镜像mirror['mir☜] n. 镜子MIT (Massachusetts Institute of Technology) 麻省理工学院moderate['m d☜rit]adj. 适度的modification [m difi'kei☞☜n ] n. 修改, 修正modulus['m djul☜s] n.系数mold[m☜uld] n. 模, 铸模, v. 制模, 造型monitor ['m nit☜ ] v. 监控monograph['m n☜♈ra:f] n. 专著more often than not 常常motivation[m☜uti'vei☞☜n] n. 动机mould split line 模具分型线moulding['m☜udi☠] n. 注塑件move away from 抛弃multi-imprssion mould 多型腔模Nnarrow['n✌r☜u] a. 狭窄的NC (numerical control ) 数控nevertheless[ nev☜❆☜'les] conj.,adv.然而,不过nonferrous['n n'fer☜s] adj.不含铁的, 非铁的normally['n :mli]adv.通常地novice['n vis] n. 新手, 初学者nozzle['n zl] n. 喷嘴, 注口numerical [nju'merikl] n. 数字的Oobjectionable [☜b'd✞ek☞☜bl] adj. 有异议的，讨厌的observe[☜b'z☜:v] vt. 观察obviously [' bvi☜sli] adv 明显地off-line 脱机的on-line 联机operational [ p☜'rei☞☜nl] adj.操作的, 运作的opportunity[ p☜'tju:niti] n. 时机, 机会opposing[☜'p☜uzi☠] a.对立的, 对面的opposite[' p☜zit] n. 反面a.对立的,对面的optimization [ ptimai'zei☞☜n] n.最优化orient [' :ri☜nt] vt. 确定方向orthodox [' : ☜d ks] adj. 正统的，正规的overall['☜uv☜r :l] a.全面的,全部的overbend v.过度弯曲overcome[☜uv☜'k✈m] vt.克服, 战胜overlaping['☜uv☜'l✌pi☠] n. 重叠overriding[☜uv☜'raidi☠] a. 主要的, 占优势的Ppack[p✌k] v. 包装package ['p✌kid✞] vt.包装pallet ['p✌lit] n.货盘panel ['p✌nl] n.面板paraffin['p✌r☜fin] n. 石蜡parallel[p✌r☜lel] a.平行的penetration[peni'trei☞☜n ] n.穿透peripheral [p☜'rif☜r☜l] adj 外围的periphery [p☜'rif☜ri] n. 外围permit[p☜'mit] v. 许可, 允许pessure casting 压力铸造pillar['pil☜] n. 柱子, 导柱pin[pin] n. 销, 栓, 钉pin-point gate 针点式浇口piston ['pist☜n] n.活塞plan view 主视图plasma['pl✌zm☜] n. 等离子plastic['pl✌stik] n. 塑料platen['pl✌t☜n] n. 压板plotter[pl t☜] n. 绘图机plunge [pl✈nd✞] v翻孔plunge[pl✈nd✞] v.投入plunger ['pl✈nd✞☜ ] n. 柱塞pocket-size 袖珍portray[p :'trei] v.描绘pot[p t] n.壶pour[p :] vt. 灌, 注practicable['pr✌ktik☜b] a. 行得通的preferable['pref☜r☜bl] a.更好的, 更可取的preliminary [pri'limin☜ri] adj 初步的，预备的press setter 装模工press[pres] n.压,压床,冲床,压力机prevent [pri'vent] v. 妨碍primarily['praim☜rili] adv.主要地procedure[pr☜'si:d✞☜] n.步骤, 方法, 程序productivity.[pr☜ud✈k'tiviti] n. 生产力profile ['pr☜ufail] n.轮廓progressively[pr☜'♈resiv] ad.渐进地project[pr☜'d✞ekt] n.项目project[pr☜'d✞ekt] v. 凸出projection[pr☜'d✞ek☞☜n] n.突出部分proper['pr p☜] a. 本身的property['pr p☜ti] n.特性prototype ['pr☜ut☜taip] n. 原形proximity[pr k'simiti] n.接近prudent['pru:d☜nt] a. 谨慎的punch [p✈nt☞] v. 冲孔punch shapper tool 刨模机punch-cum-blanking die 凹凸模punched tape 穿孔带purchase ['p☜:t☞☜s] vt. 买，购买push back pin 回程杆pyrometer[pai'n mit☜] n. 高温计Qquality['kwaliti] n. 质量quandrant['kw dr☜nt] n. 象限quantity ['kw ntiti] n. 量，数量quench[kwent☞] vt. 淬火Rradial['reidi☜l] adv.放射状的ram [r✌m] n 撞锤.rapid['r✌pid]adj. 迅速的rapidly['r✌pidli]adv. 迅速地raster['r✌st☜] n. 光栅raw [r :] adj. 未加工的raw material 原材料ream [ri:m] v 铰大reaming[ri:mi☠] n. 扩孔, 铰孔recall[ri'k :l] vt. 记起, 想起recede [ri'si:d] v. 收回, 后退recess [ri'ses] n. 凹槽,凹座,凹进处redundancy[ri'd✈nd☜nsi] n. 过多re-entrant 凹入的refer[ri'f☜:] v. 指, 涉及, 谈及reference['ref☜r☜ns] n.参照,参考refresh display 刷新显示register ring 定位环register['red✞st☜] v. 记录, 显示, 记数regrind[ri:'♈aind](reground[ri:'gru:nd]) vt.再磨研relative['rel☜tiv] a. 相当的, 比较的relay ['ri:lei] n. 继电器release[ri'li:s] vt. 释放relegate['rel☜geit] vt. 把··降低到reliability [rilai☜'biliti] n. 可靠性relief valves 安全阀relief[ri'li:f] n.解除relieve[ri'li:v ]vt.减轻, 解除remainder[ri'meind☜] n. 剩余物, 其余部分removal[ri'mu:vl] n. 取出remove[ri'mu:v] v. 切除, 切削reposition [rip☜'zi☞☜n] n.重新安排represent[ repri'zent☜] v 代表,象征reputable['repjut☜bl] a. 有名的, 受尊敬的reservoir['rez☜vwa: ] n.容器, 储存器resident['rezid☜nt] a. 驻存的resist[ri'zist] vt.抵抗resistance[ri'zist☜ns] n.阻力, 抵抗resolution[ rez☜'lu:☞☜n] n. 分辨率respective[ri'spektiv] a.分别的,各自的respond[ris'p nd] v.响应, 作出反应responsibility[risp ns☜'biliti] n.责任restrain[ris'trein]v.抑制restrict [ris'trikt] vt 限制，限定restriction[ris'trik☞☜n] n. 限制retain[ri'tein] vt.保持, 保留retaining plate 顶出固定板reveal [ri'vil] vt.显示，展现reversal [ri'v☜sl] n. 反向right-angled 成直角的rigidity[ri'd✞iditi] n. 刚度rod[r d] n. 杆, 棒rotate['r☜uteit] vt.(使)旋转rough machining 粗加工rough[r✈f] a. 粗略的routine [ru:'ti:n] n. 程序rubber['r✈b☜] n.橡胶runner and gate systems 流道和浇口系统Ssand casting 砂型铸造satisfactorily[ s✌tis'f✌ktrili] adv. 满意地saw[a :] n. 锯子scale[skeil]n. 硬壳score[sk :] v. 刻划scrap[skr✌p] n.废料, 边角料, 切屑screwcutting 切螺纹seal[si:l] vt.密封secondary storagesection cutting plane 剖切面secure[si'kju☜] v.固定secure[si'kju☜] vt.紧固,夹紧,固定segment['se♈m☜nt] v. 分割sensitive['sensitiv]a.敏感的sequence ['si:kw☜ns] n. 次序sequential[si'kwen☞☜l] a.相继的seriously['si☜ri☜sli] adv.严重地servomechanism ['s☜:v☜'mek☜nizm] n.伺服机构Servomechanism Laboratoies 伺服机构实验室servomotor ['s☜:v☜m☜ut☜] n.伺服马达setter ['set☜] n 安装者set-up 机构sever ['sev☜] v 切断severity [si'veriti] n. 严重shaded[☞✌did] adj.阴影的shank [☞✌☠k] n. 柄.shear[☞i☜]n.剪,切shot[☞t] n. 注射shrink[☞ri☠k] vi. 收缩side sectional view 侧视图signal ['si♈nl] n.信号similarity[simi'l✌riti] n.类似simplicity[sim'plisiti] n. 简单single-point cutting tool 单刃刀具situate['sitjueit] vt. 使位于, 使处于slide [slaid] vi. 滑动, 滑落slideway['slaidwei] n. 导轨slot[sl t] n. 槽slug[sl✈♈] n. 嵌条soak[s☜uk] v. 浸, 泡, 均热software ['s ftw☪☜] n. 软件solid['s lid] n.立体, 固体solidify[s☜'lidifai] vt.vi. (使)凝固, (使)固化solution[s☜'lu:☞☜n] n.溶液sophisiticated [s☜'fistikeitid] adj.尖端的,完善的sound[saund] a. 结实的, 坚固的)spark erosion 火花蚀刻spindle['spindl] n. 主轴spline[splain] n.花键split[split] n. 侧向分型, 分型spool[spu:l] n. 线轴springback n.反弹spring-loaded 装弹簧的sprue bush 主流道衬套sprue puller 浇道拉杆square[skw☪☜] v. 使成方形stage [steid✞] n. 阶段standardisation[ st✌nd☜dai'zei☞☜n] n. 标准化startling['sta:tli☠] a. 令人吃惊的steadily['sted☜li ] adv. 稳定地step-by-step 逐步stickiness['stikinis] n.粘性stiffness['stifnis] n. 刚度stock[st k] n.毛坯, 坯料storage tube display 储存管显示storage['st :rid✞] n. 储存器straightforward[streit'f :w☜d]a.直接的strain[strein] n.应变strength[stre☠] n.强度stress[stres] n.压力,应力stress-strain应力--应变stretch[stret☞] v.伸展strike [straik] vt. 冲击stringent['strind✞☜nt ] a.严厉的stripper[strip☜] n. 推板stroke[strouk] n. 冲程, 行程structrural build-up 结构上形成的sub-base 垫板subject['s✈bd✞ikt] vt.使受到submerge[s☜b'm☜:d✞] v.淹没subsequent ['s✈bsikwent] adj. 后来的subsequently ['s✈bsikwentli] adv. 后来, 随后substantial[s☜b'st✌n☞☜l] a. 实质的substitute ['s✈bstitju:t] vt. 代替,.替换subtract[s☜b'tr✌kt] v.减, 减去suitable['su:t☜bl] a. 合适的, 适当的suitably['su:t☜bli] ad.合适地sunk[s✈☠k](sink的过去分词) v. 下沉, 下陷superior[s☜'pi☜ri☜] adj.上好的susceptible[s☜'sept☜bl] adj.易受影响的sweep away 扫过symmetrical[si'metrikl] a. 对称的synchronize ['si☠kr☜naiz] v.同步,同时发生Ttactile['t✌ktail] a. 触觉的, 有触觉的tailstock['teilst k] n.尾架tapered['teip☜d] a. 锥形的tapping['t✌pi☠] n. 攻丝technique[tek'ni:k] n. 技术tempering['temp☜r☠] n.回火tendency['tend☜nsi] n. 趋向, 倾向tensile['tensail] a.拉力的, 可拉伸的拉紧的, 张紧的tension ['ten☞☜n] n.拉紧,张紧terminal ['t☜:m☜nl ] n. 终端机terminology[t☜:mi'n l☜d✞i ] n. 术语, 用辞theoretically [ i:☜'retikli ] adv.理论地thereby['❆☪☜bai] ad. 因此, 从而thermoplastic[' ☜:m☜u'pl✌stik] a. 热塑性的, n. 热塑性塑料thermoset[' ☜:m☜set] n.热固性thoroughly[' ✈r☜uli] adv.十分地, 彻底地thread pitch 螺距thread[ red] n. 螺纹thrown up 推上tilt [tilt] n. 倾斜, 翘起tolerance ['t l☜r☜ns] n..公差tong[t ☠] n. 火钳tonnage['t✈nid✞] n.吨位, 总吨数tool point 刀锋tool room 工具车间toolholder['tu:lh☜uld☜] n.刀夹,工具柄toolmaker ['tu:l'meik☜] n 模具制造者toolpost grinder 工具磨床toolpost['tu:l'p☜ust] n. 刀架torsional ['t :☞☜nl] a扭转的.toughness['t fnis] n. 韧性trace [treis] vt.追踪tracer-controlled milling machine 仿形铣床transverse[tr✌ns'v☜:s] a. 横向的tray [trei] n. 盘，盘子，蝶treatment['tri:tm☜nt] n.处理tremendous[tri'mend☜s] a. 惊人的, 巨大的trend [trend] n.趋势trigger stop 始用挡料销tungsten['t✈☠st☜n] n.钨turning['t☜:ni☠] n.车削twist[twist ] v.扭曲，扭转two-plate mould 双板式注射模Uultimately['✈ltimitli] adv终于.undercut moulding 侧向分型模undercut['✈nd☜k✈t] n. 侧向分型undercut['✈nd☜k✈t] n.底切underfeed['✈nd☜'fi:d] a, 底部进料的undergo[✈nd☜'♈☜u] vt.经受underside['✈nd☜said] n 下面,下侧undue[✈n'dju:] a.不适当的, 过度的uniform['ju:nif :m] a.统一的, 一致的utilize ['ju:tilaiz] v 利用Utopian[ju't☜upi☜n] adj.乌托邦的, 理想化的Vvalve[v✌lv] n.阀vaporize['veip☜raiz] vt.vi. 汽化, (使)蒸发variation [v☪☜ri'ei☞☜n] n. 变化various ['v☪☜ri☜s] a.不同的,各种的vector feedrate computation 向量进刀速率计算vee [vi:] n. v字形velocity[vi'l siti] n.速度versatile['v☜s☜tail] a.多才多艺的,万用的vertical['v☜:tikl] a. 垂直的via [vai☜] prep.经,通过vicinity[v☜'siniti] n.附近viewpoint['vju:p int] n. 观点Wwander['w nd☜] v. 偏离方向warp[w :p] v. 翘曲washer ['w ☞☜] n. 垫圈wear [w☪☜] v.磨损well line 结合线whereupon [hw☪☜r☜'p n] adv. 于是winding ['waindi☠] n. 绕, 卷with respect to 相对于withstand[wi❆'st✌nd] vt.经受,经得起我的词汇库work[w☜:k] n. 工件workstage 工序wrinkle['ri☠kl] n.皱纹vt.使皱Yyield[ji:ld] v. 生产Zzoom[zu:] n. 图象电子放大11。

压铸工艺专业术语压铸(diecasting)铜丝刷磨面(brushedsurfacebybrassbrushwheels)QC巡检(QCtour-inspection)全检(full-inspection)钻孔(drilling)攻牙(tapping)钝化(passivat剪水口(degating)冲内窗口(internalframetrimming)磨四边批锋(removingflasharoundexternalframe)刮顶针批锋(removingburrsroundpadsofejectorpin)锉内窗四边(filinginternalframe)内窗四边磨砂纸(abradinginternalframebyabrasivepaper 刮四按钮孔(removingburrsin4buttonholes)ing)喷油前全检(full-inspectionpriortopainting)抹天那水(wipingwithtoluene)背面喷面油(applyingtopcoattobottomsurface)表面喷底油(applyingprimercoattotopsurface)烘干(baking)表面喷面油(applyingtopcoattotopsurface)移印/丝印(PADprinting/silkscreening)抽检(samplinginspection)全检(full-inspection)包装(packaging）原材料入厂(incominginwarehouse)来料抽检(IQC)压铸(diecasting)冲水口(degating)两侧/上下/曲面磨#320砂(abrasivebeltgrindingonbothsides/topandbottom/curvedsurface:#320grit) 手磨边角(manualsandingatedge/corner)全检(full-inspection)QC抽检(QCsamplinginspection)上挂(racking)超声波除腊(ultrasonicclean)过水(rinsing)热浸除油(soakcleaning)阴极电解除油(electroclean)巡检(tour-inspection)沉锌(zincdeposit)活化(activation)半光镍(semi-brightnickel)回收(collection)哑镍(mattenickel-plating)光铬(brightchromium-plating)后处理过水(rinsingafterfinishing)。

压铸常用英文词汇 V5广东文灿压铸有限公司Wencan die casting Co., Ltd常用英语术语列表List of die casting terms and vocabularies( 2011-9-23 re-edit V6)1.新产品以及模具开发 products and tooling developing 2D/3D drawing 平面图/3维图bump among products 货与货之间碰撞capital equipment 资本设备, 固定设备chamfering倒角classification 分类、级别datums 基准datum level 基准水平面datum line 基准线datumplane 【测】基(准)面design/process FMEA D设计/P过程FMEAdie casting 压铸die fabrication 模具加工Die location layout 工模排位图Die polished 省模Die trial 试模electrode for EDM 放电用铜公machining by CNC wire-cut machine 线切割加工machining by electric discharge machine ( EDM ) 电蚀火花加工potential effects of failure 潜在失效后果potential failure mode 潜在失效模式rib and corner 筋肋和尖角subcontractor 外包商set die-casting parameter/locking force/ injection force/injection velocity/shot time/volume of release agent/die-open time/ ejector time/pressurerating/metaltemperature/ control temperature/ operation according to WI按工作指示设定压铸参数/锁模力/射料力/射料速度/打锤时间/喷雾量/开模时间/顶出时间/压力参数/料温/控制温度/按照作业指导书作业;thermal expansion 热膨胀2(热处理 heat treatmentair cooling 空气冷却annealing 退火carbonization 碳化case hardening 表面硬化，表面淬硬full annealing 完全退火1heat treatment 热处理metallographic structure 金相组织 metallographic test 金相试验quenching 淬火residual stress 残余应力tempering 回火3(压铸设备及模具 die casting machine and die toolingangle pin 斜导销biscuit /slug 料饼/余料blister 气泡burner 燃烧器casting area最大压铸面积casting insert 铸件镶件casting fin铸件飞边, 铸件披缝, 铸件周缘翅片 cavity fill time 充型时间cavity insert 型腔镶块cavity 型腔center furnace 中央熔炉clamp force max. 最大压力coefficient 系数cold chamber machine 冷压室压铸机 cold/hot chamber pressure die-casting machine 冷/热室压铸机contraction 收缩core slides/core 活动抽芯(型芯) cover die half(stationary half )/ ejector die half (moveable half ) 前(定)模/后(动)模crucible furnace 坩埚炉crucible pot 坩埚degassing 除气/去气delivery rate;pouring rate 充型流速/浇注速度design of gating system 浇注系统设计 die layout模具排位图die life 模具寿命die stroke 开模行程draft 拔模斜度ejector force顶出力ejector pad 顶针痕ejector pin 顶针ejector stroke 顶出行程feeding 补缩foundry returns 回炉料gating/running system 浇注系统 holding furnace 保温炉ingate 内浇道injection plunger 压射冲头ladle 浇包2locking force 锁模力machine platen 压铸机模板 moving/fixed platen 动/定模板maximum/minimum die height 最大/最小压模厚度metal fluidity (金属)流动性 molten metal 熔化金属nitrogen pressure 氮气压力 normal pressure工作压力numerical simulation of casting solidification 铸件凝固数值模拟opening time 留型时间/开型时间 overflow 溢流槽/ 渣包production die 量产模prototype die 样板模refining 精炼refining agent 精炼剂remelting 重熔riser/feeder head 冒口runner 横浇道runner/gate 流道/浇口scrap 废金属料secondary alloy 再生合金 shot sleeve 司筒,压射室size of die platen 模板尺寸 slag 熔/炉渣sludge/dross 沉/浮渣solidification 凝固sprue pin(spreader) 直浇道锥(分流器)spure 直浇道die frame 模架tangential runner 切向横浇道 tie bar 哥林柱/导柱/拉杆 total melting loss 熔炼损耗率熔损、烧损trim die 冲模vent 排气口water cooling channel 冷却水通道4(压铸工艺与后加工工艺 die casting and secondary processalloy component assay report 合金成份化验报告appearance外观center furnace 中央溶炉 characteristics 特性degating 冲水口die casting 压铸parting line 分型线polishing/buffing 磨/抛光 polishing 抛光、磨光3polishing/cotton wheels 抛光用布轮 removing burrs round pads of ejector pin 刮项针位批锋removing parting line flash 磨分型线sanding wheels 砂布轮5(精加工工艺 machining process boring 镗精加工 fine maching ; 粗加工 rough maching drill bit 钻头卧式加工中心Horizontal machining center chuck 车床卡盘，夹具立式加工中心vertical machining center cutting tools刀具external/internal thread 外/内螺纹file 锉form tool 成型刀grind 磨jig/fixture 夹具lathe 车床left-hand thread左旋螺纹length of thread engagement螺纹旋合长度 loose thread滑牙machining accuracy加工精度machining allowance of casting 铸件机械加工余量 machining allowance 加工余量machining error加工误差mandrel 机加工芯轴mill 铣minor diameter小径parallel screw thread圆柱螺纹pitch diameter中径pitch螺距plane 刨,Reaming铰孔right-hand thread 右旋螺纹rolled threads 挤牙root diameter底径screw thread 螺纹tapping 攻牙tight thread牙紧uncompleted tapping 牙不完整6(表面处理 surface treatmenta mixture of 2 parts water and 3 parts oil 2分水3分油混合acid dip/pickling 酸洗acid 酸水alkali cleaning 碱洗Anodizing 阳极氧化baking 烘干4blueing /chemical oxide 钢铁发蓝/化学氧化 chemical pretreatment 化成处理chromating 铬化clear black e-coatings透明黑色泳漆 clear chroming 无色铬化colored passivation 彩色钝化 concentration 浓度dedusting 除尘degreasing 脱脂，除油descaling 刻蚀dipping 浸渍electrophoresis 电泳electrophoretic coating 电泳漆electroplating hard chrome 镀硬铬electrostatics powder coatings 静电粉沫喷涂 E-plating 电镀hexavalent chromium 六价铬impregnation 浸渗mechanical polishing机械抛光neutralization 中和PAD printing/silk screening 移印/丝印passivating 钝化phosphating 磷化resin 树脂rinsing 过清水Roughtening 粗化spray powder 喷粉taking down 下挂trivalent chromium 三价铬ultrasonic clean 超声波清洗wiping with toluene 抹天那水salt spray testing 盐雾试验7(品质控制 quality control appearance full-inspection 外观全检collection 回收evaluation / measurement technique 评价/测量技术 first inspection for 5 shots 首检5件Freq=frequency 次数incoming quality sampling inspection report 来料质量抽查报告interprocess quality sampling inspection report 工序间质量抽查报告pile products up due to laying in disorder 摆放不正确堆积产品processing tour-inspection 制程巡回检查 product/process specification /tolerance 产品/过程规范/公差 projector 投影仪QC tour-inspection QC巡检quality final-inspection report 最终检验质量报告5quality first piece inspection report 质量首件检查报告quality traceability analysis report 质量追踪分析表return to supplier 退回供应商 sampling inspection 抽检self-inspection 自检Special Char. class 特殊特性分类 spot check 抽样检查visual standard 外观标准workmanship standard 工作质量标准8.质量缺陷常用语 defects air tightness 气密性blister/pimple/bubble 起泡bumps 碰伤caniniform/dentate狗牙casting fin铸件飞边, 铸件披缝, 铸件周缘翅片 cold lap 冷隔cold shut 冷纹Contamination 污染dirt pits 尘点distortion/deformation 变形double skin 重皮ejector marks raised or depressed 顶针位凹凸elephant skin皱皮entrapped slag;slag inclusion 夹渣 filling to excess 多料flow mark 流痕/波纹 flow line incomplete filling 缺料incorrect casting form 形状不合格 indentation 印痕/凹痕internal quality of casting 铸件内在质量 micro-shrinkage;porosity 疏松【显微疏松】 off dimension;off size 尺寸不合格 oil marks 油渍orange peel 桔皮缺陷out of size 尺寸不符oxidation 氧化partial breakage of a casting 崩料 peeling 电镀脱皮pinhole针孔pits 面麻porosity 砂孔roughness 粗糙sand inclusion 砂眼scratches 划痕/刮伤shrinkage 缩水slag 炉渣6stain 污渍texturing 致密性thermal shrinkage crack (on product) (产品中的)热缩裂raised crack mark line (on product) (产品表面凸起的龟裂线) visual quality of casting 铸件外观质量 void 砂眼/气孔warpage 挠曲yellowing发黄yield of casting 铸件合格品率missrun 欠铸9. 压铸件试验常用语 testing adhesion 附着性deflection 挠度elastoplasticity 弹塑性elongation 延伸率extend 延伸film thickness 涂膜厚度film thickness gauge 膜厚仪 flexibility 屈曲挠性hardness 硬度heat impact test 热冲击试验high humidity test 高湿测试humidity resistance 耐湿impact resistance 抗冲击力impact strength 冲击性measuring adhesion by tape test 胶带附着力测试neutral salt-spray NSS test 中性盐雾 residual stress 残余应力spraying viscosity 喷涂粘度 strengthen 加强、巩固tension 拉紧、张力viscosity 粘度water resistance 耐水性yield strength 屈服强度mechanical property 力学性能 chemical analysis 化学成份10.测量工具常用语 measurement and gaugeAltitude gauge 高度仪average 平均值Block Gauge 块规Bore Gauge 孔规Clearance gauge 塞尺/间隙规CMM 三坐标测试仪Depth Micrometer 深度千分尺 Digital caliper 电子卡尺Digital Height Gauge 数字高度测量仪7durometer/hardness meter 硬度计 Electric/digital Balance 电子称Electroplating THK.Tester 电镀厚度测试仪 equipment variation 设备变差gage repeatability and reproducibility report 量具的R&R重复性和再现性报告go-no-go gauge “过” -- “不过” 验规通-止规 HRC/HV Hardness Tester 洛/维氏硬度仪 Rockwell testingimpact tester 冲击仪Inside/outer Micrometer 内/外径千分尺 measurement unit analysis 测量设备分析 Micrometer Calipers 千分卡尺Microscope 显微镜 metallographic microscope 金相显微镜Multimeter 万用表 electric universal testing 电子万能试验机normal distribution curve 正态分布曲线 number of parts 零件数量number of trials 实验次数one range 单极差part variation 零件变差pin gauge 针规Plug gage 塞规Projector 投影仪 Optical image 光学影像测量仪 range 公差带range control chart 极差控制图repeatability 重复性reproducibility再现性Ring Gauge 环规spectrometer 光谱仪Thermometer 温度计Thread Gauge 螺纹规thread plug gage螺纹塞规Torque Meter 力矩计total variation 总变差Twisting Meter 转扭力仪Vernier Caliper 游标卡尺viscosimeter 粘度计visual check 目测witness mark (测量)参考(标)点endoscope 内窥镜11. 形位公差常用语 tolerance angularity 倾斜度角度aperture 孔径basic dimension 基本尺寸basic size 基本尺寸c/c =between centers 中心距centricity中心circular runout 圆跳动circularity 圆度 roundness8concentricity 同轴度同心度conical 圆锥形的coordinate data 坐标数据coordinate dimensioning 坐标尺寸 cylindricity 圆柱度datum/feature/point/line/ plane/axis 基准/特征/点/线/平面/轴线deviation偏差diameter/radius 直径/半径draft angle 拔模斜度ellipse 椭圆excentricity 偏心距(率)flatness 平面度geometric dimensioning 几何尺寸 fit/clearance fit/interference fit/ transition fits 配合/间隙配合/过盈配合/过渡配合M/LMC=maximum/least material condition 最大/小材料状态nominal diameter 公称直径oblong 长方形oblong hole 椭圆孔ovality 圆锥度(变形)parallelism 平行度perpendicularity 垂直度position 位置度profile of a line 线轮廓度profile of a surface 面轮廓度reference frame 坐标系right angle 直角rounds/fillets draft 外圆角/内圆角拔模斜度 square 正方形standard/ precision tolerance 标准/精度公差 straightness 直线度symmetry 对称度theoretical size 理论正确尺寸thickness厚度tolerance/value 公差/值top/side/ end view 顶/测/端视图 total runout 全跳动unilateral/bilateral tolerance 单/双边公差 upper/lower deviation 上/下偏差 12.包装和包装材料 package bar code 条形码blister plate/PVC tray 吸塑罩bubble bag 气泡袋closed /sealed poly bag 封口胶袋 corrugated cardboard/sheet波纹隔板corrugated egg-crate carton 瓦楞蛋格卡通箱 foam bag 珍珠棉袋forktruck 叉车9GW gross weight /NW net weight 毛/凈重 If wooden pallet, the certificate of disinfection for pallet 如果是木制卡板要有卡板消毒熏蒸证明in egg tray with carton packages 卡通箱及其蛋格 item/ sales consumer pack 单件装label 包装标识logo polybag 有唛胶袋multipack 多件装outside dimensions 长x宽x高 length x width x height 外部尺寸packaging materials 包装材料packaging strapping/PP-straps包装带pad separator; clapboard; partition board/sheet 隔板 pallet 卡板plastic container 胶箱shrinkage package 吸塑包装single/double/3 regular slotted carton/box 单/双/三坑纸箱 styrofoam 聚苯乙烯泡沫塑料白色泡沫 tissue papper 拷贝纸transparent plastic film circle the pallet/stretch poly wrap 透明膜保鲜纸unitload pallet 整卡装wrappage 包装材料13.生产控制计划 production control control plan 控制计划core team 核心小组date Rev. 日期修订date orig. 日期编制each batch 每批Inform line/team leader/ supervisor/manager to shut down and recheck 通知生产拉/组长/主管/经理，停机再检查machine adjustment 调机machine, device, jig, tools for Mfg. 生产工艺装备 material identification 物料标识mounting die 安装模具mounting die inspection sheet 模具安装检查清单 once every operation 每次开机part /process number 零件/过程编号part name/description 零件名称/描述pre-launch 试生产process 过程process name/operation description 过程名称/操作描述 reaction plan反应计划refer to CP 参考控制计划14.优质浇口设计七步法 gate design10优质浇口设计七步法The Seven Steps To A Quality Gating Design第一步确定铸件质量等级。

压铸英语A 安装尺寸 install dimension凹模固定板 retainer plate凹模 female die, female mold, negative moldB 备件 spare parts变质 modification变质剂 modification agent扒渣 slagging-off保温炉 holding furnace保压压力 dwell pressure表面缺陷 surface defectC 淬火硬度quenching hardness抽芯core侧面抽芯side core抽芯油缸core oil cylinder插拔式结构plug抽芯机构core puller抽芯油缸支架bracket of cylinder粗糙度roughness/degree铸件表面粗糙度surface roughness擦伤galling尺寸公差dimension tolerance of casting 除气degassing吹气净化blow purifying除气剂degassing flux出渣de-slagging出渣口slag hole沉渣sludge出炉口tap hole菜花头Cauli-flowering超声波检验ultrasonic test重熔re-meltingD 端盖cover动模垫块spacer parallel锻钢 forged steel氮化处理nitriding treatment断裂fracture塑性断裂plastic fracture导柱guide pillar导套guide sleeve导向板guide plate导向件guide part 动型moving die/ejector die/movable mould动模座板moving clamp plate/bottom clamping plate定模座板fixed clamp plate/top plate 定型fixed die/cover die定模套版bolster/fixed die顶杆ejector pin顶出结构ejector mechanism顶出ejector吊装孔lifting eye吊环lifting ring镀钛处理titanium plating treatment 多肉缺陷metallic projection电火花electric spark打磨grindingF 分流锥 divider/blast cone分型面 mold parting/parting face/mold joint附页 attachment/appendix复位杆 reset bar(rod)附件故障 accessory覆盖剂 covering flux废金属料scrap浮渣cinder反射炉 reverberatory furnace废品 reject飞边joint flash仿真simulationG 规格 specification/standard数值孔径 numerical aperture (N.A) 固定段 segment坩埚crucible坩埚炉crucible furnace感应电炉electric induction furnace 沟槽 blind scab硅SiliconH 滑块 sliding block滑块部件 moving parts滑块退让 return/move back焊补 welding-on横浇道 runner合模 die locking横流道 runner回炉料foundry returns合型 mold assembling/closing/die locking 合型力 die locking force化学成分不合格chemical consistence analysisJ 浇口套 sprue bush浇排道系统pouring system浇不足 misrun浇注 pouring浇注断裂interrupted pour浇道比 gating ratio浇包 ladle精整dressing and finishing精度 accuracy接口 connector击伤 shot damage金相组织 metallographic structure金属残液heel金相检验metallographic test金属型涂料 die coating/coating for metal mold加压速度 rate of pressure increasing间隙 clearance精炼refining精炼剂refining flux精密铸造 precision casting静置holding/stewing渗透 impregnation集渣装置dirt traps夹杂类缺陷inclusion defects夹渣entrapped slag/slag inclusion夹具 tool fixturesK 壳体 housing开炉 blowing in孔洞缺陷cavity库存 inventoryL 冷却 cooling冷却水管 cooling water pipe冷却耐压管 cooling pressure pipe冷却水管用密封圈 O-ring/sealingring/gasket ring冷室卧式压铸机 horizontal (cold chamber) die casting machine冷却系统 cooling system冷却水接口 cooling water connector 冷裂 cold crack冷隔 cold lap铝 Aluminum裂纹 crack拉伤 caught casting拉杆孔 draw bar螺纹 screw/thread螺纹结构 screw structure螺纹公称直径(直径 diameter)公称尺寸(名义尺寸) specifiedsize/nominal dimension漏油 leakage of oil棱边倒角 edge炉料 charge炉衬 furnace lining炉气分析flue gas analysis炉前分析on-the-spot sample analysis流痕 bloom/flow line力学性能不合格 physical-mechanical characteristic abnormalM 毛坯 rough/blank毛坯铸件 rough casting毛刺 veining/burr模芯 core模框 frame模槽 mold channel模套 chase/bolster/frame模具钢 die steel模具图纸 mold drawing内浇口 in-gate冒口 riser/feeder head冒口浇注系统 feeder head gating system 镁 Magnesium锰 Manganese密闭耐压系统 tightness testN 内浇道 in-gate镍 NickleP 配油盘 pressure plate排气块 exhaust block排气槽 air vent排气孔 vent/venting channel排气塞 venting plug配合套圆形:fitting sleeve 方型: fitting case跑铝 aluminum slop out of mold喷射冶金 injecting metallurgy喷丸清理 shot blasting cleaning抛丸清理 wheel blasting cleaning偏析 segregation破坏性实验 destructive testQ 取件机 extractor去除浇冒口 de-gating清铲 chipping缺陷铸件 defecting casting气孔 blowhole/gascavity/pinhole/porosity气孔缩 blowhole shrinkage去毛刺 de-burring去除氧化皮 de-scaling氢 Hydrogen清理 cleaningR 热处理 heat treatment热电偶测温孔 thermocouple well热电偶 thermocouple (TC)/pyod热裂 hot heating熔炼 smelting熔化率 melting rate熔炼损耗 total melting loss熔池 bath熔剂 flux熔渣 slagS 水管 water pipe三维造型 3 D三坐标测量仪 coordinate 3上模座板 upper clamping plate缩孔 shrinkage缩松 dispersed shrinkage疏松 porosity(dispersed shrinkage)渗漏 leakage缩陷 sink/sink in/depression试块 test block/test piece/coupon实时控制系统 real-time control system 试模 de-buggingT 推板 push plate推杆 push rod推板导柱 push plate guide pillar推板导套 push plate guide sleeve凸模固定板 punch-retainer plate铜 copper钛 Titanium W 网状裂纹 craze crack/crazing/checking 未浇满 poured shortX 型芯 core型腔 mold cavity镶拼处 splicing place斜导柱孔 hole of inclined guide pillar 楔紧块 wedge型芯弯曲 core bending下模座板 lowering clamping plate型芯固定板 core-retainer plateX 光射线检验 X-ray inspectionY 压铸机 die casting machine压室 pressure chamber压室止口(定位)尺寸 dimension/size压实 squeezing compaction压射 shot/injection压射冲头 injection piston(ram)/plunger 压铸型 die casting die压力铸造模具 die-casting die易损镶块 wear insert易损件 wearing parts预应力 pre-stress永久型 permanent mold硬点 hard spot溢流槽 over flow well印痕 indentation氧 Oxygen荧光检验 fluorescent testZ 真空接口 vacuum connector真空排气管 vacuum exhaust block总接头 main connector中接头 middle connector直浇道 sprue转接处(转口)transit装配图(铸型装配图) mold assembly drawing铸钢 cast steel支架 ejector housing/mold base leg造渣 slag forming真空熔炼 vacuum melting真空压铸 vacuum die casting/ evacuated die casting增压 pressurization针孔 pinhole沾铝 adhesive aluminum直读光谱分析仪 direct-reading spectrograph转运包 transfer ladle转向器steering rack柴油式传动叉车 Diesel forklift复印机 copying machine服务器 Server绘图仪 Graphic plotter兼容机 compatible machine材料库 warehouse投影仪 projector半自动车床 semi-automatic lathe半自动立式钻床 drill machine表面粗度测量仪 surface roughness gauge 布洛维硬度计 Brinell hardness gauge测氢仪 Hydrogen gauge叉车充电机 charger程控交换机 exchanger齿轮油泵 oil pump储气罐 accumulator tank电动葫芦 Gantry crane电动试压泵 press tester电动斜切机 bias cutter电子秤 weighing scale电子扫描仪 scanner吊斗 spoon hopper高压离心风机 combustion blower管道泵 process water pump烘箱 oven监控系统 monitoring system简易数控车床 digital lathe交流弧焊机 Are welder抛光机 polisher锯床 saw空压机 air compressor冷冻式干燥机 dryer红外线测温仪冷却塔 cooling tower立式带锯床 band saw滤油机 oil filter焊接机 welder模温机 die heater喷粉室回收设备 painter system平面磨床 grinder气动量仪 air gauge 切割机 cut-off machine清洗机 washer散热器攻丝机 tapping machine台式光谱仪 spectrograph台式砂轮机 abrasive machine卧式液压拉床 broaching machine铣床 milling machine钻床 drilling machine液压机 hydraulic machine真空机 vacuum pump时效炉 aging furnace电阻炉 stress relief furnace探伤机 diagnostic machine加工中心 machining center车床 lathe钻削中心 drilling & cutting center别克 Buick切边机 trim press冷却塔循环泵 cooling tower pump循环水离心泵 process water pump脱模剂压送机 die lube station取件机 extractorFL充痒压铸系统 FL oxygen feed die cast system装卸车 loader在建工程 construction in progress捡漏机 picker纸芯式滤油器paper element filter电磁阀 solenoid valve溢流阀spillover valve调速阀 speed control valve压力传感器pressure transducer三角带wedge shaped belt节流阀throttle governor同步齿型带timing belt喷涂机spray coater轴承(main) bearing浮球阀 float valve/ball cock行车bridge crane平衡重式叉车counter balanced forklift 轮毂螺栓wheel hub bolt制动蹄片brake shoe制动液braking fluid叶片lamina/vane侧护板side guard plate单列向心推力球轴承single row radial thrust ball bearing带防尘盖单列轴承single row bearing shielded急停按钮 scram button三相开关threephase switch行程开关 limit/travel switch断路器circuit breaker接触器 contactor中间继电器intermediate relay时间继电器 time relay控制变压器control transformer开关电源switching supply节能灯energy-saving lamp日光灯管fluorescent tube自整流高压汞灯泡self-rectifying high pressure mercury lamp电工胶布garrers/electrical tape焊条welding rod石笔slate pencil外圆磨床external grinderHydraulic fluid oil 液压油Safety hook/bolts 安全钩Crosshead 十字头Tail stock 尾架尾座Frame cover 护板框盖Toggle top cover 肘环顶Coupling 联轴器Tie-bar 拉杆, 系杆Control panel 控制面板Power board 分配板, 配电板Overhauling 大修, 拆修Hose 软管, 水龙带Warranty period 保修期Nozzle 管口, 喷嘴Nature tan 日晒后的颜色, 茶色Electric fitting 电装、Rubber pad 橡胶垫Shock absorbing rubber stopper 减震橡皮塞Die height 模子闭合高度Die stroke 动模行程Intensification ratio standard 增强比标准Plunger stroke 柱塞行程Plunger tip penetration 冲头穿透力Viscosity index 粘度指数Rated pressure 额定压力Plug socket 插口, 塞孔Ventilated 通风的Anchor bolt hole 地锚(脚)螺栓孔Inlet 入口Galvanize 通电流Carbon grain 碳粒Mortar 火泥, 砂浆Stretcher 拉伸机Earthing cable 接地电缆Manifold 总管, 集合管Clamp force sensor 夹紧力传感器Attenuate 削弱Emulsification 乳化作用中子线 wire for sliding出模斜度 draft angle隔皮 bur掉肉 misrun研配 grindTurbidity 浑浊度Refract meter 折光仪Sediment 沉淀物Glycol 乙二醇Combustible 易燃的Water-soluble 水溶性的Grease pump 黄油泵，油脂泵Drooling 滴料Disulfide 二硫化物Lithium 锂Gauge cock 试水位旋塞Pressure match valve 压力拟合阀Lock/check nut 防松螺母Slant 倾斜Core sliding face 型芯滑面Flux treatment 熔剂处理Die clamping cylinder 模具夹紧气缸Clogging 堵塞，闭合Electrode bar 电极棒Fumigation certificate 熏蒸消毒证书Crate 条板箱，柳条箱Resin parts 树脂零件Oil ring 油环Gear box 齿轮箱，传动箱,变速箱Draft angle 出模斜度Tap and drill gauge 丝锥及钻头规Tap borer 螺纹底孔钻Tap cutter 丝锥刀具Tap die holder 丝锥板牙两用夹头Tap handle 丝锥扳手Screw funnel 分液漏斗Screw chasing machine 螺纹切削机Screw cutting 螺纹切削Screw pitch gauge 螺距规Screw rivet 螺纹铆钉Screw vent 螺杆通孔Rack housing 齿条罩Rack Tubes 油缸Cup Seals Feed Pipes 输油管Spools 卷轴Recuperating Seal(恢复性密封) Inflator Tubes 充气.Cut Seals Steering Hoses 转向胶管Biscuit thickness 料柄厚度注油孔 oil filter point牛皮纸 kraft/brown paper瓦楞纸 fluting paper崩料 charge downslide/collapse卡涉现象 interference phenomenon 机械加工余量 stocking复制模 replaced mould偏心距 offset distance抽大缸 pull tie bar料头 biscuit抽芯 loose core光整平滑度 flatnessDrain cock 排气阀，放出开关Wrench 扳手Stopper 塞子，制动器Intensifier 增强器Check valve 止回阀Orifice 孔，口Pilot valve 领示阀，导阀Cold shut 冷疤，冷结Flow mark 波纹，流线谱Shot stroke 压射冲程Surge pressure 冲击压力，脉动压力Jack bolt 定位螺栓Anchor hole 锚栓孔Dust seal 档尘圈Valve cover 气门盖，阀盖Cylinder tube 汽缸筒Piston rod 活塞杆Piston ring 活塞环Shot cylinder 压射缸Wire clamp 钢丝钳Air hose 空气软管，送风管Atomizer 喷雾器Strainer 滤网Hollow shaft 空心轴，管轴Potentiometer 电位计，分压计Shaft 轴，杆状物Asbestos wire 石棉线Pulley 滑车，滑轮Spring washer 弹簧垫圈Inverter 电源交换器Cutting fluid 切削液refraction coefficient 折光系数Screw Cutting Tap 螺旋切削丝锥plug gauge 塞规color shade色泽red lead power 红丹粉stress relief 去应力casting film 铸型薄膜cast form铸造成形, 铸型cast house crane炉前[出铁场]吊车cast panel铸造面板cast rotor铸造转子cast superalloy铸造高温合金cast test block铸造试块[棒]casting character铸造性能casting crack缩裂casting fin铸件飞边, 铸件披缝, 铸件周缘翅片casting head浇冒口casting lap铸件皱纹casting scar铸疤, 浇注疤casting sealer铸件渗补剂casting strain铸造应变casting stress铸造应力spark plug 火花塞internal-combustion engine cylinder内燃机汽缸hydraulics 水力学pinion小齿轮pinion bearing小齿轮轴承pinion cage主动[行星]齿轮架, 差速器壳, 差速盘pinion cutting machine齿轴切削机床pinion head齿轴齿顶pinion shaped cutter插齿刀pinion spider差速器十字轴pinion stop(起动机的)齿轮停止器valve housing阀套valve actuating mechanism配气机构valve air relief自动放气阀valve bank阀组valve barrel阀缸valve body attachment阀体连接头valve bounce阀跳valve bush阀衬, 阀[衬]套valve chest gasket阀柜垫密片valve cock阀栓valve cottar气阀制销valve disc阀盘valve discharge centrifuge活门卸料式离心机valve follower阀推杆valve positioner阀门定位器分层Delaminationfilling-engine梳丝机器filling agent 填充剂;填料filling auger装载螺旋filling compoun填料filling funnel注液漏斗车架 (car) frame钣金 sheet metal测板 side plate内侧板Inner side plate焊钳soldering turret焊条 welding rod焊点 welding spot焊接机器人 welding robot寿命周期成本 life cycle cost前轴 fore/leading axle后翼子板 rear fender切削性能 cutting characteristic散热性能 heat dispersion耐磨性能 wear resistant property摩擦系数 friction coefficient 灰铸铁 gray iron; graphitic cast iron过盈配合 tight/interference fit缸套 cylinder, sleeve, barrel tube pipe导轨面 guide way (face)铣刀盘 face milling cutter/facing cutter刀盘 tool pan/cutter head磨削余量 grinding allowance耐用性 endurance钝化 passivation刀尖圆弧 circular profile of knife point (刀具)主偏角 entering angle; plan angle 弹性变形量 amount of elastic deformation 燃烧室 combustion chamber磨屑 abrasive dust滤器芯 strainer core差速器 differential gear反冲减震器 recoiling shock absorber废气涡轮 exhaust turbine涡轮增压器 turbocharger增压盲区 turboloch喷油器 oil sprayer/atomizer汽化器 carburetor硬质合金刀具 carbide tipped tool精镗刀具 fine boring tool动力传动系统 power transmission system spanner 扳子 (美作:wrench)double-ended spanner 双头扳子adjustable spanner, monkey wrench 活扳子,活络扳手box spanner 管钳子 (美作:socket wrench calipers 卡规pincers, tongs 夹钳wire cutters 剪线钳multipurpose pliers, universal pliers 万能手钳adjustable pliers 可调手钳punch 冲子scraper 三角刮刀reamer 扩孔钻calliper gauge 孔径规hacksaw 钢锯grease gun 注油枪oil can 油壶边刨床 side planer插床 slotting machine车刀 lathe tool车轮车床 car wheel lathe车削 turningBayonet 卡口Bearing fittings 轴承配件Bearing processing equipment 轴承加工机Belt drive 带传动Bending machines 弯曲机Boring heads 搪孔头Boring machines 镗床Cable making tools 造线机CNC bending presses 电脑数控弯折机CNC boring machines 电脑数控镗床CNC drilling machines 电脑数控钻床CNC EDM wire-cutting machines 电脑数控电火花线切削机CNC electric discharge machines 电脑数控电火花机CNC engraving machines 电脑数控雕刻机CNC grinding machines 电脑数控磨床CNC lathes 电脑数控车床CNC machine tool fittings 电脑数控机床配件CNC milling machines 电脑数控铣床CNC shearing machines 电脑数控剪切机CNC toolings CNC刀杆CNC wire-cutting machines 电脑数控线切削机Conveying chains 输送链Crimping tools 卷边工具Disposable toolholder bits 舍弃式刀头Drawing machines 拔丝机Etching machines 蚀刻机Honing machines 搪磨机Lapping machines 精研机Milling heads 铣头Mold polishing/texturing 模具打磨/磨纹Planing machines 刨床aberration 色差atomization 雾化bank mark 料纹bite 咬入blacking hole 涂料孔(铸疵)blacking scab 涂料疤blister 起泡blooming 起霜blow hole 破孔blushing 泛白body wrinkle 侧壁皱纹breaking-in 冒口带肉bubble 膜泡burn mark 糊斑burr 毛边camber 翘曲cell 气泡centre buckle 表面中部波皱check 细裂痕checking 龟裂chipping 修整表面缺陷clamp-off 铸件凹痕collapse 塌陷colour mottle 色斑corrosion 腐蚀crack 裂痕crazing 碎裂crazing 龟裂deformation 变形edge 切边碎片edge crack 裂边fading 退色filler speak 填充料斑fissure 裂纹flange wrinkle 凸缘起皱flaw 刮伤flow mark 流痕galling 毛边glazing 光滑gloss 光泽grease pits 污斑grinding defect 磨痕haircrack 发裂haze 雾度incrustation 水锈indentation 压痕internal porosity 内部气孔mismatch 偏模mottle 斑点necking 缩颈nick 割痕orange peel 橘皮状表面缺陷overflow 溢流peeling 剥离pit 坑pitting corrosion 点状腐蚀plate mark 模板印痕pock 麻点pock mark 痘斑resin streak 树脂流纹resin wear 树脂脱落riding 凹陷sagging 松垂saponification 皂化scar 疤痕scrap jam 废料阻塞scratch 刮伤/划痕scuffing 深冲表面划伤seam 裂痕shock line 模口挤痕short shot 充填不足shrinkage pool 凹孔sink mark 凹痕skin inclusion 表皮折叠straightening 矫直streak 条状痕surface check 表面裂痕surface roughening 橘皮状表皮皱折surging 波动sweat out 冒汗torsion 扭曲warpage 翘曲waviness 波痕webbing 熔塌weld mark 焊痕whitening 白化wrinkle 皱纹表面处理关联用语时效硬化 age hardening气体硬化 air hardening空气韧化 air patterning退火 annealing阳极效应 anode effect阳极氧化处理 anodizing滚镀 barrel plating滚筒打光 barrel tumbling 染黑法 blackening青熟脆性 blue shortness碳酸盐薄膜防锈法 bonderizing箱位退火 box annealing封箱渗碳 box carburizing辉面电镀 bright electroplating光辉热处理 bright heat treatment旁路热处理 bypass heat treatment 化学电镀 chemical plating化学蒸镀 chemical vapor deposition 大气热处理 controlled atmosphere 锐角效应 corner effect儒缓放电 creeping discharge压花 embossing部分淬火 selective quenching。

铸造专业术语英文
铸造 (foundry) 是一种将熔化金属或其他材料倒入模具中，然后使其凝固和冷却以获得所需形状和尺寸的制造过程。

铸造是一种广泛应用的制造技术，用于制造各种零件和设备，例如汽车发动机零件、飞机部件、船舶零件、计算机零件和电子设备组件等。

以下是一些铸造专业术语的英文:
1. Foundry - 铸造厂
2. Furnace - 熔炉
3. Mold - 模具
4. Torch - 熔炉炬
5. Furnace gas - 熔炉气体
6. Iron ore - 铁矿石
7. Coal - 煤
8. Coke - 焦粉
9. Dross - 金属氧化物
10. Foundry process - 铸造过程
11. billet - 铸件
12. casting - 铸件
13. gating - 浇口
14. Shell - 壳模
15. foundry equipment - 铸造设备
16. float - 浮砂
17. draw - 拉砂
18. blow - 吹砂
19. malleable iron - 可铸铁
20. Hardened steel - 硬化钢
这些专业术语对于铸造工人、工程师和研究人员来说非常重要，因为它们用于描述铸造过程中的各种步骤和材料。

组装、冲压、喷漆等专业词汇Assembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Pneumatic screw driver气动起子worktable 工作桌OOBA开箱检查fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet栈板barcode条码barcode scanner条码扫描器fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cosmetic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs. inch镑、英寸EMI gasket导电条front plate前板traightener整平机punching machine 冲床robot机械手hydraulic 液压rear plate后板chassis基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试V oltage switch of SPS电源电压接拉键sheet metal parts 冲件plastic parts塑胶件SOP制造作业程序material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线left fork叉车personnel resource department人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and s machine油压机lathe车床planer |'plein|刨床miller铣床grinder磨床driller??床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vice sectionsuperisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布tname of a department部门名称a o load material上料to unload material卸料to return material/stock to退料scraped |'skræpid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |' ksi'dein|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车更多精品文档trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓dministration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单screwdriver holder起子插座pedal踩踏板stopper阻挡器flow board流水板hydraulic handjack油压板车forklift叉车pallet栈板glove(s)手套glove(s) with exposed fingers割手套thumb大拇指forefinger食指midfinger中指ring finger无名指little finger小指band-aid创可贴iudustrial alcohol工业酒精alcohol container沾湿台head of screwdriver起子头sweeper扫把mop拖把vaccum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋chain链条jack升降机production line流水线chain链条槽magnetizer加磁器lamp holder灯架to mop the floor拖地to clean the floor扫地to clean a table擦桌子air pipe 气管packaging tool打包机packaging打包missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a little bigger尺寸偏大(小)cosmetic defect外观不良slipped screwhead/slippery screw head螺丝滑头slipped screwhead/shippery screwthread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色scratch划伤poor processing 制程不良poor incoming part事件不良fold of pakaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍polishing/surface processing表面处理exposed metal/bare metal金属裸露lack of painting烤漆不到位safety安全quality品质delivery deadline交货期cost成本engineering工程die repair模修enterprise plan = enterprise expansionprojects企划QC品管die worker模工production, to produce生产equipment设备to start a press开机stop/switch off a press关机classification整理regulation整顿cleanness清扫conservation清洁culture教养qualified products, up-to-gradeproducts良品defective products, not up-to-gradeproducts不良品waste废料board看板feeder送料机sliding rack滑料架defective product box不良品箱die change 换模to fix a die装模to take apart a die拆模to repair a die修模packing material包材basket蝴蝶竺更多精品文档plastic basket胶筐isolating plate baffle plate; barricade隔板carton box纸箱to pull and stretch拉深to put material in place, to cut material, to input落料to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料transportation运输(be)qualfied, up to grade合格not up to grade, not qualified不合格material change, stock change材料变更feature change 特性变更evaluation评估prepare for, make preparations for 准备parameters参数rotating speed, revolution转速manufacture management制造管理abnormal handling异常处理production unit生产单位lots of production生产批量steel plate钢板roll material卷料manufacture procedure制程operation procedure作业流程to revise, modify修订to switch over to, switch---tothrow--over switching over切换engineering, project difficulty工程瓶颈stage die工程模automation自动化to stake, staking, reviting铆合add lubricating oil加润滑油shut die架模shut height of a die架模高度analog-mode device类模器die lifter举模器argon welding氩焊vocabulary for stamping冲压常词汇stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, blockstop 定位块reset复位smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货to return delivenry to.to send delinery backto retrn of goods退货registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收to notice通知application form for purchase请购单consume, consumption消耗to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked 断裂to lubricate润滑common vocabulary for dieengineering模具工程常用词汇die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die连续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap切边更多精品文档to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder文件夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备waste materials废料work in progress product在制品casing = containerazation装箱quantity of physical invetory secondcount 复盘点数量quantity of customs count会计师盘,点数量the first page第一联filed by accounting department forreference会计部存查end-user/using unit(department)使用单位summary of year-end physicalinventory bills年终盘点截止单据汇总表bill name单据名称This sheet and physical inventory listwill be sent to accountingdepartment together (Those of NHKwill be sent to financialdepartment)本表请与盘点清册一起送会计部－(NHK厂区送财会部)Application status records of year-endphysical inventory List andphysical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO.空白与作废单号plate电镀mold成型material for engineering mold testing工程试模材料not included in physical inventory不列入盘点sample样品incoming material to be inspected进货待验description品名steel/rolled steel钢材material statistics sheet物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点chairman主席present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedulesheetPCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory differenceanalysis sheet年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量更多精品文档cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕??shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线更多精品文档patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸)draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号)shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板更多精品文档die set下模座bottom block下垫脚bottom plate下托板(底板)stripping plate内外打(脱料板)outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相关英文compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具移转成型用模具encapsulation molding低压封装成型射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道h=0.02~0.05mmw=3.2mmL=3~5mmwelding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆)slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口H=F=1/2t~1/5tT=2.5~3.5mmdiaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Φ0.8~1.0mmRunner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣更多精品文档品质人员名称类QC quality control 品质管理人员FQC final quality control 终点品质管制人员IPQC in process quality control 制程中的品质管制人员OQC output quality control 最终出货品质管制人员IQC incoming quality control 进料品质管制人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance 出货质量保证人员QE quality engineering 品质工程人员品质保证类FAI first article inspection 新品首件检查FAA first article assurance 首件确认TVR tool verification report 模具确认报告3B 3B 模具正式投产前确认CP capability index 能力指数CPK capability index of process 模具制程能力参数SSQA standardized supplier quality合格供应商品质评估OOBA out of box audit 开箱检查QFD quality function deployment品质机能展开FMEA failure model effectivenessanalysis 失效模式分析8 disciplines 8项回复内容FA final audit 最後一次稽核CAR corrective action request 改正行动要求corrective action report 改正行动报告FQC运作类AQL Acceptable Quality Level 运作类允收品质水准S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的AOQ Average Output Quality 平均出厂品质AOQL Average Output QualityLevel 平均出厂品质Q/R/S Quality/Reliability/Service品质/可靠度服务MIL-STD Military-Standard 军用标准S I-S IV Special I-Special IV 特殊抽样水准等级P/N Part Number 料号L/N Lot Number 特采AOD Accept On Deviation 特采UAI Use As It 首件检查报告FPIR First Piece Inspection Report百万分之一PPM Percent Per Million 批号制程统计品管专类SPC Statistical Process Control 统计制程管制SQC Statistical Quality Control 统计品质管制R Range 全距AR Averary Range 全距平均值UCL Upper Central Limit 管制上限LCL Lower Central Limit 管制下限MAX Maximum 最大值MIN Minimum 最小值GRR GaugeReproducibility&Repeatability 量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径FREQ Frequency 频率N Number 样品数其它品质术语类QCC Quality Control Circle 品质圈QIT Quality Improvement Team 品质改善小组PDCA Plan Do Check Action 计划执行检查总结ZD Zero Defect 零缺点QI Quality Improvement 品质改善QP Quality Policy 目标方针TQM Total Quality Management全面品质管理MRB Material Reject Bill 退货单LQL Limiting Quality Level 最低品质水准RMA Return Material Audit 退料认可QAN Quality Amelionrate Notice品质改善活动ADM Absolute DimensionMeasuremat 全尺寸测量QT Quality Target 品质目标7QCTools 7 Quality Controll Tools品管七大手法通用之件类ECN Engineering Change Notes 工更多精品文档程变更通知(供应商)ECO Engineering Change Order 工程改动要求(客户)PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Specification In Process 制程检验规格SOP Standard Operation Procedure 制造作业规范IS Inspection Specification 成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类QC Quality System 品质系统ES Engineering Standarization 工程标准CGOO China General PCE龙华厂文件H Huston (美国)休斯敦C Compaq (美国)康伯公司C China 中国大陆A Assembly 组装(厂)S Stamping 冲压(厂) P Painting 烤漆(厂)I Intel 英特尔公司T TAIWAN 台湾IWS International WorkmanStandard 工艺标准ISO International StandardOrganization 国际标准化组织GS General Specification 一般规格CMCS C-China M-ManufactC-Compaq S-Stamping Compaq产品在龙华冲压厂制造作业规范CQCA Q-Quality A-AssemblyCompaq产品在龙华组装厂品管作业规范CQCP P-Painting Compaq产品在龙华烤漆厂品管作业规范部类PMC Production & MaterialControl 生产和物料控制PPC Production Plan Control 生产计划控制MC Material Control 物料控制ME Manafacture Engineering 制造工程部PE Project Engineering 产品工程部A/C Accountant Dept 会计部P/A Personal & Administration 人事行政部DC Document Center 资料中心QE Quality Engineering 品质工程(部)QA Quality Assurance 品质保证(处)QC Quality Control 品质管制(课)PD Product Department 生产部LAB Labratry 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部P Painting 烤漆(厂)A Asssembly 组装(厂)S Stamping 冲压(厂)生产类PCS Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供应商)识别码SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号其它OEM Original EquipmentManufacture 原设备制造PCE Personal Computer Enclosure个人电脑外设PC Personal Computer 个人电脑CPU Central Processing Unit 中央处理器SECC SECC` 电解片SGCC SGCC 热浸镀锌材料NHK North of Hongkong 中国大陆PRC People's Republic of China中国大陆U.S.A the United States of America美国A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量VS 以及REV Revision 版本JIT Just In Time 零库存I/O Input/Output 输入/输出OK Ok 好NG Not Good 不行,不合格C=0 Critical=0 极严重不允许ESD Electry-static Discharge 静电更多精品文档排放5S 希腊语整理,整顿,清扫,清洁,教养ATIN Attention 知会CC Carbon Copy 副本复印相关人员APP Approve 核准,认可,承认CHK Check 确认AM Ante Meridian 上午PM Post Meridian 下午CD Compact Disk 光碟CD-ROM Compact Disk Read-Only Memory 只读光碟FDD Floppy Disk Drive 软碟机HDD Hard Disk Drive 碟碟机REF Reference 仅供参考CONN Connector 连接器CA V Cavity 模穴CAD Computer Aid Design 计算机辅助设计ASS'Y Assembly 装配,组装MAT'S Material 材料IC Integrated Circuit 集成电路T/P True Position 真位度TYP Type 类型WDR Weekly Delivery Requitement 周出货需求C?T Cycle Time 制程周期L/T Lead Time 前置时间(生产前准备时间) S/T Standard Time 标准时间P/M Product Market 产品市场3CComputer,Commumcation,Consumerelectronic's 消费性电子5WIHWhen,Where,Who,What,Why,How to5MMan,Machine,Material,Method,Measurement4MIHMan,Materia,Money,Method,Time人力,物力,财务,技术,时间(资源)SQA Strategy Quality Assurance策略品质保证DQA Desigh Quality Assurance 设计品质保证MQA Manufacture QualityAssurance 制造品质保证SSQA Sales and service QualityAssurance 销售及服务品质保证LRR Lot Rejeet Rate 批退率BS Brain storming 脑力激荡EMI Electronic Magnetion Inspect高磁测试FMI Frequency Modulatim Inspect高频测试B/M Boar/Molding(flat cable)C/P Connector of PCA/P AssemblySPS Switching power supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital Vedio DiskVCD Vdeio Compact DiskLCD Liquid Crystal DisplayCAD Computer AID DesignCAM Computer AID ManufacturingCAE Computer AID EngineeringABIOS Achanced Basic input/output system 先进的基本输入/输出系统CMOS Complemeruary MetollOxide Semiconductor 互补金属氧化物半导体PDA Personal Digital Assistant 个人数字助理IC Integrated Circuit 集成电路ISA Industry Standard Architecture工业标准体制结构MCA Micro Channel Architecture微通道结构EISA Extended Industry StandardArchitecture 扩充的工业标准结构SIMM Single in-line memorymodule 单项导通汇流组件DIMM Dual in-line Memory Module双项导通汇流组件LED Light-Emitting Diode 发光二级管FMEA Failure Mode Effectivenes失效模式分析W/H Wire Harness 金属线绪束集组件F/C Flat Calle 排线PCB Printed Circuit Board 印刷电路板CAR Correction Action Report 改善报告NG Not Good 不良WPR Weekly Delivery Requirement周出货要求PPM Parts Per Million 百万分之一TPM Total Production Maintenance全面生产保养MRP Material Requiremcnt Planning物料需计划OC Operation System 作业系统TBA To Be Design 待定,定缺D/C Drawing ChangeP/P Plans & ProceduneEMI Electrical-Music Industry 电子音乐工业RFI Read Frequency Input 读频输入MMC Maximum Material ConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material Size更多精品文档模具技术用语各种模具常用成形方式accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming ?泡成形sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warmforging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matchedmould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模landed plungermold 有肩柱塞式模具burnishing die 挤光模landed positivemold 有肩全压式模具button die 镶入式圆形凹模loadingshoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold活动式模具clod hobbing 冷挤压制模louveringdie 百叶窗冲切模composite dies 复合模具manifolddie 分歧管模具counter punch 反凸模modular mold组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bendingdie 双折冷弯模具extrusion die 挤出模palletizing die叠层模family mold 反套制品模具plastermold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die压紧模fishtail die 鱼尾形模具profile die轮廓模flash mold 溢料式模具progressivedie 顺序模gypsum mold 石膏铸模protablemold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing)压花起伏成形re-entrant mold 倒角式模具sectionaldie 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positivemold 半全压式模具shaper 定型模套single cavity mold单腔模具solid forging die 整体锻模splitforging die 拼合锻模split mold 双并式模具spruelessmold 无注道残料模具squeezing die 挤压模stretch form die拉伸成形模sweeping mold 平刮铸模swing die振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold通用模具unscrewing mold 退扣式模具yoketype die 轭型模模具厂常用之标准零配件air vent vale 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流更多精品文档档板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 托架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁) cavity retainer plate 模穴托板center pin 中心梢clamping block 锁定块coil spring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底die block 块形模体die body 铸模座die bush 合模衬套die button 冲模母模die clamper 夹模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲模板die set 冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejectorleader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘?flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧?goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶?冲头headless punch直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram压射柱塞inlay busher 嵌入衬套inner plunger内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶?lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢locatingring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush 活动衬套making die 打印冲子manifold block歧管档块master plate 靠模样板match plate分型板mold base 塑胶模座mold clamp 铸模紧固夹mold platen 模用板moving bolster换模保持装置moving bolster plate 可动侧模板onepiece casting 整体铸件parallel block 平行垫块paring line分模线parting lock set 合模定位器passguide 穴型导板peened head punch 镶入式冲头pilotpin 导?pin gate 针尖浇口plate 衬板pre extrusion punch 顶挤冲头punch冲头puncher 推杆pusher pin 衬套梢rack 机架rapping rod 起模杆re-entrant mold 凹入模retainer pin嵌件梢retainer plate 托料板return pin 回位梢riding stripper 浮动脱模器ring gate环型浇口roller 滚筒runner 流道runner ejector set 流道顶出器runnerlock pin 流道拉梢screw plug 头塞set screw 固定螺丝shedder 脱模装置shim 分隔片shoe 模座之上下模板shoot 流道shoulder bolt 肩部螺丝skeleton 骨更多精品文档。

压铸及机械英语词汇(2009-09-01 20:11:44)压铸及机械词汇A 安装尺寸 install dimension[in·stall || ɪn'stɔːl]v.安装; 使就职; 安置[di·men·sion || dɪ'menʃn]n.尺寸, 容积, 次元凹模固定板 retainer plate凹模 female die, female mold, negative moldB 备件 spare parts变质 modification [mod·i·fi·ca·tion || 'mɑdɪfɪ'keɪʃn /'mɒ-]n.修改; 缓和; 改变; 减轻变质剂 modification agent [a·gent || 'eɪdʒənt]n.代理人; 仲介人; 代理商; 间谍, 特工, 密探扒渣 slagging-off [slæg]n.矿渣, 火山岩渣, 炉渣v.使成渣; 诋毁; 辱骂; 结成渣保温炉 holding furnace [hold·ing || 'həʊldɪŋ]n.把持, 保持, 支持hold[həʊld]n.抓住, 握住; 可手攀的东西, 支撑点; 握法; 掌握#延迟, 延期v.握着; 夹住; 抓住; 托住; 持续, 保持; 有效, 适用; 顶住, 支持[fur·nace || 'fɜrnɪs /'fɜːn-]n.火炉, 磨练, 熔炉保压压力 dwell pressure[dwel]v.居住; 踌躇pressure[pres·sure || 'preʃə(r)]n.压, 按, 榨v.对...施加压力; 迫使表面缺陷 surface defect defect[de·fect || 'diːfekt]n.缺点, 不足之处, 缺陷v.逃跑, 背叛, 脱离C 淬火硬度quenching hardnessquenching n.淬火; 熄quench[kwentʃ]v.压制, 抑制; 熄灭; 解; 扑灭hardness[hard·ness || 'hɑrdnɪs /'hɑː-]n.坚硬; 硬度; 硬性; 困难抽芯core core[kɔː]n.核心, 争论的核心, 果心v.挖...的核侧面抽芯side core抽芯油缸core oil cylindercylinder[cyl·in·der || 'sɪlɪndə]n.圆筒, 圆筒状之物; 硬盘里有形存储单位(计算机用语) 插拔式结构plugplug[plʌg]n.塞子, 栓; 插头, 插塞; 堵塞物; 火花塞, 点火栓v.堵, 插上, 塞; 苦干, 苦读; 连接; 接通电源; 枪击抽芯机构core pullerpuller['pʊlə(r)]n.拉者; 吸引人的东西; 拉具抽芯油缸支架bracket of cylinder粗糙度roughness/degreeroughness[rough·ness || 'rʌfnɪs]n.粗糙, 崎岖不平; 猛烈; 粗暴, 粗鲁, 粗野; 狂风大浪degree[de·gree || dɪ'griː]n.程度, 学位, 度数铸件表面粗糙度surface roughness擦伤galling尺寸公差dimension tolerance of castingdimension[di·men·sion || dɪ'menʃn]n.尺寸, 容积, 次元tolerance['tol·er·ance || 'tɑlərəns /'tɒl-]n.宽容, 宽大; 公差, 容限; 忍耐, 忍耐力; 耐受性, 耐药量除气degassing吹气净化blow purifyingpurify[pu·ri·fy || 'pjʊrɪfaɪ/'pjʊər-]v.使纯净, 提纯, 净化; 纯净除气剂degassing fluxflux[flʌks]n.流出, 变迁, 涨潮v.使成流体; 使出血; 使熔化; 熔化; 流出出渣de-slaggingslag[slæg]n.矿渣, 火山岩渣, 炉渣v.使成渣; 诋毁; 辱骂; 结成渣出渣口slag hole沉渣sludgesludge[slʌdʒ]n.泥, 泥状雪, 泥泞出炉口tap holetap[tæp]n.轻拍, 轻敲, 轻叩; 鞋底; 鞋掌#龙头, 阀门; 分接头; 塞子, 栓子; 搭线窃听v.轻拍, 轻敲, 轻叩; 补鞋底; 轻轻敲出; 指定, 选定; 轻拍, 轻敲, 轻叩; 装上塞子; 接通; 在上刻痕取液; 在...装窃听器菜花头Cauli-floweringflowering[flow·er·ing || 'flaʊərɪŋ]n.开花; 繁荣; 成熟adj.有花的; 开花的flower[flow·er || 'flaʊə(r)]n.花, 盛时, 精华v.开花; 成熟; 旺盛; 用花装饰; 使开花超声波检验ultrasonic test重熔re-meltingD 端盖cover动模垫块spacer parallelspacer[spac·er || 'speɪsə(r)]n.取间隔的装置; 逆电流器锻钢 forged steel氮化处理nitriding treatment断裂fracture塑性断裂plastic fracture导柱guide pillar导套guide sleeve导向板guide plate导向件guide part动型moving die/ejector die/movable mould动模座板moving clamp plate/bottom clamping plate 定模座板fixed clamp plate/top plate定型fixed die/cover die定模套版bolster/fixed die顶杆ejector pin顶出结构ejector mechanism顶出ejector吊装孔lifting eye吊环lifting ring镀钛处理titanium plating treatment多肉缺陷metallic projection电火花electric spark打磨grindingF 分流锥 divider/blast cone分型面 mold parting/parting face/mold joint附页 attachment/appendix复位杆 reset bar(rod)附件故障 accessory覆盖剂 covering flux废金属料scrap浮渣cinder反射炉 reverberatory furnace废品 reject飞边joint flash仿真simulationG 规格 specification/standard数值孔径 numerical aperture (N.A)固定段 segment坩埚crucible坩埚炉crucible furnace感应电炉electric induction furnace沟槽 blind scab硅SiliconH 滑块 sliding block滑块部件 moving parts滑块退让 return/move back焊补 welding-on横浇道 runner合模 die locking横流道 runner回炉料foundry returns合型 mold assembling/closing/die locking合型力 die locking force化学成分不合格chemical consistence analysisJ 浇口套 sprue bush浇排道系统pouring system浇不足 misrun浇注 pouring浇注断裂interrupted pour浇道比 gating ratio浇包 ladle精整dressing and finishing精度 accuracy接口 connector击伤 shot damage金相组织 metallographic structure金属残液heel金相检验metallographic test金属型涂料 die coating/coating for metal mold 加压速度 rate of pressure increasing间隙 clearance精炼refining精炼剂refining flux精密铸造 precision casting静置holding/stewing渗透 impregnation集渣装置dirt traps夹杂类缺陷inclusion defects夹渣entrapped slag/slag inclusion夹具 tool fixturesK 壳体 housing开炉 blowing in孔洞缺陷cavity库存 inventoryL 冷却 cooling冷却水管 cooling water pipe冷却耐压管 cooling pressure pipe冷却水管用密封圈 O-ring/sealing ring/gasket ring冷室卧式压铸机 horizontal (cold chamber) die casting machine 冷却系统 cooling system冷却水接口 cooling water connector冷裂 cold crack冷隔 cold lap铝 Aluminum裂纹 crack拉伤 caught casting拉杆孔 draw bar螺纹 screw/thread螺纹结构 screw structure螺纹公称直径(直径 diameter)公称尺寸(名义尺寸) specified size/nominal dimension漏油 leakage of oil棱边倒角 edge炉料 charge炉衬 furnace lining炉气分析flue gas analysis炉前分析on-the-spot sample analysis流痕 bloom/flow line力学性能不合格 physical-mechanical characteristic abnormalM 毛坯 rough/blank毛坯铸件 rough casting毛刺 veining/burr模芯 core模框 frame模槽 mold channel模套 chase/bolster/frame模具钢 die steel模具图纸 mold drawing内浇口 in-gate冒口 riser/feeder head冒口浇注系统 feeder head gating system镁 Magnesium锰 Manganese密闭耐压系统 tightness testN 内浇道 in-gate镍 NickleP 配油盘 pressure plate排气块 exhaust block排气槽 air vent排气孔 vent/venting channel排气塞 venting plug配合套圆形:fitting sleeve 方型: fitting case 跑铝 aluminum slop out of mold喷射冶金 injecting metallurgy喷丸清理 shot blasting cleaning抛丸清理 wheel blasting cleaning偏析 segregation破坏性实验 destructive testQ 取件机 extractor去除浇冒口 de-gating清铲 chipping缺陷铸件 defecting casting气孔 blowhole/gas cavity/pinhole/porosity 气孔缩 blowhole shrinkage去毛刺 de-burring去除氧化皮 de-scaling氢 Hydrogen清理 cleaningR 热处理 heat treatment热电偶测温孔 thermocouple well热电偶 thermocouple (TC)/pyod热裂 hot heating熔炼 smelting熔化率 melting rate熔炼损耗 total melting loss熔池 bath熔剂 flux熔渣 slagS 水管 water pipe三维造型 3 D三坐标测量仪 coordinate 3上模座板 upper clamping plate缩孔 shrinkage缩松 dispersed shrinkage疏松 porosity(dispersed shrinkage)渗漏 leakage缩陷 sink/sink in/depression试块 test block/test piece/coupon实时控制系统 real-time control system 试模 de-buggingT 推板 push plate推杆 push rod推板导柱 push plate guide pillar推板导套 push plate guide sleeve凸模固定板 punch-retainer plate铜 copper钛 TitaniumW 网状裂纹 craze crack/crazing/checking 未浇满 poured shortX 型芯 core型腔 mold cavity镶拼处 splicing place斜导柱孔 hole of inclined guide pillar楔紧块 wedge型芯弯曲 core bending下模座板 lowering clamping plate型芯固定板 core-retainer plateX 光射线检验 X-ray inspectionY 压铸机 die casting machine压室 pressure chamber压室止口(定位)尺寸 dimension/size压实 squeezing compaction压射 shot/injection压射冲头 injection piston(ram)/plunger压铸型 die casting die压力铸造模具 die-casting die易损镶块 wear insert易损件 wearing parts预应力 pre-stress永久型 permanent mold硬点 hard spot溢流槽 over flow well印痕 indentation氧 Oxygen荧光检验 fluorescent testZ 真空接口 vacuum connector真空排气管 vacuum exhaust block总接头 main connector中接头 middle connector直浇道 sprue转接处(转口)transit装配图(铸型装配图) mold assembly drawing铸钢 cast steel支架 ejector housing/mold base leg造渣 slag forming真空熔炼 vacuum melting真空压铸 vacuum die casting/ evacuated die casting增压 pressurization针孔 pinhole沾铝 adhesive aluminum直读光谱分析仪 direct-reading spectrograph 转运包 transfer ladle转向器steering rack柴油式传动叉车 Diesel forklift复印机 copying machine服务器 Server绘图仪 Graphic plotter兼容机 compatible machine材料库 warehouse投影仪 projector半自动车床 semi-automatic lathe半自动立式钻床 drill machine表面粗度测量仪 surface roughness gauge布洛维硬度计 Brinell hardness gauge测氢仪 Hydrogen gauge叉车充电机 charger程控交换机 exchanger齿轮油泵 oil pump储气罐 accumulator tank电动葫芦 Gantry crane电动试压泵 press tester电动斜切机 bias cutter电子秤 weighing scale电子扫描仪 scanner吊斗 spoon hopper高压离心风机 combustion blower管道泵 process water pump烘箱 oven监控系统 monitoring system简易数控车床 digital lathe交流弧焊机 Are welder抛光机 polisher锯床 saw空压机 air compressor冷冻式干燥机 dryer红外线测温仪冷却塔 cooling tower立式带锯床 band saw滤油机 oil filter焊接机 welder模温机 die heater喷粉室回收设备 painter system平面磨床 grinder气动量仪 air gauge切割机 cut-off machine清洗机 washer散热器攻丝机 tapping machine台式光谱仪 spectrograph台式砂轮机 abrasive machine卧式液压拉床 broaching machine铣床 milling machine钻床 drilling machine液压机 hydraulic machine真空机 vacuum pump时效炉 aging furnace电阻炉 stress relief furnace探伤机 diagnostic machine加工中心 machining center车床 lathe钻削中心 drilling & cutting center别克 Buick切边机 trim press冷却塔循环泵 cooling tower pump循环水离心泵 process water pump脱模剂压送机 die lube station取件机 extractorFL充痒压铸系统 FL oxygen feed die cast system 装卸车 loader在建工程 construction in progress捡漏机 picker纸芯式滤油器paper element filter电磁阀 solenoid valve溢流阀spillover valve调速阀 speed control valve压力传感器pressure transducer三角带wedge shaped belt节流阀throttle governor同步齿型带timing belt喷涂机spray coater轴承(main) bearing浮球阀 float valve/ball cock行车bridge crane平衡重式叉车counter balanced forklift轮毂螺栓wheel hub bolt制动蹄片brake shoe制动液braking fluid叶片lamina/vane侧护板side guard plate单列向心推力球轴承single row radial thrust ball bearing 带防尘盖单列轴承single row bearing shielded急停按钮 scram button三相开关threephase switch行程开关 limit/travel switch断路器circuit breaker接触器 contactor中间继电器intermediate relay时间继电器 time relay控制变压器control transformer开关电源switching supply节能灯energy-saving lamp日光灯管fluorescent tube自整流高压汞灯泡self-rectifying high pressure mercury lamp 电工胶布garrers/electrical tape焊条welding rod石笔slate pencil外圆磨床external grinderHydraulic fluid oil 液压油Safety hook/bolts 安全钩Crosshead 十字头Tail stock 尾架尾座Frame cover 护板框盖Toggle top cover 肘环顶Coupling 联轴器Tie-bar 拉杆, 系杆Control panel 控制面板Power board 分配板, 配电板Overhauling 大修, 拆修Hose 软管, 水龙带Warranty period 保修期Nozzle 管口, 喷嘴Nature tan 日晒后的颜色, 茶色Electric fitting 电装、Rubber pad 橡胶垫Shock absorbing rubber stopper 减震橡皮塞Die height 模子闭合高度Die stroke 动模行程Intensification ratio standard 增强比标准Plunger stroke 柱塞行程Plunger tip penetration 冲头穿透力Viscosity index 粘度指数Rated pressure 额定压力Plug socket 插口, 塞孔Ventilated 通风的Anchor bolt hole 地锚(脚)螺栓孔Inlet 入口Galvanize 通电流Carbon grain 碳粒Mortar 火泥, 砂浆Stretcher 拉伸机Earthing cable 接地电缆Manifold 总管, 集合管Clamp force sensor 夹紧力传感器Attenuate 削弱Emulsification 乳化作用中子线 wire for sliding出模斜度 draft angle隔皮 bur掉肉 misrun研配 grindTurbidity 浑浊度Refract meter 折光仪Sediment 沉淀物Glycol 乙二醇Combustible 易燃的Water-soluble 水溶性的Grease pump 黄油泵，油脂泵Drooling 滴料Disulfide 二硫化物Lithium 锂Gauge cock 试水位旋塞Pressure match valve 压力拟合阀Lock/check nut 防松螺母Slant 倾斜Core sliding face 型芯滑面Flux treatment 熔剂处理Die clamping cylinder 模具夹紧气缸Clogging 堵塞，闭合Electrode bar 电极棒Fumigation certificate 熏蒸消毒证书Crate 条板箱，柳条箱Resin parts 树脂零件Oil ring 油环Gear box 齿轮箱，传动箱,变速箱Draft angle 出模斜度Tap and drill gauge 丝锥及钻头规Tap borer 螺纹底孔钻Tap cutter 丝锥刀具Tap die holder 丝锥板牙两用夹头Tap handle 丝锥扳手Screw funnel 分液漏斗Screw chasing machine 螺纹切削机Screw cutting 螺纹切削Screw pitch gauge 螺距规Screw rivet 螺纹铆钉Screw vent 螺杆通孔Rack housing 齿条罩Rack Tubes 油缸Cup Seals Feed Pipes 输油管Spools 卷轴Recuperating Seal(恢复性密封) Inflator Tubes 充气.Cut Seals Steering Hoses 转向胶管Biscuit thickness 料柄厚度注油孔 oil filter point牛皮纸 kraft/brown paper瓦楞纸 fluting paper崩料 charge downslide/collapse 卡涉现象 interference phenomenon 机械加工余量 stocking复制模 replaced mould偏心距 offset distance抽大缸 pull tie bar料头 biscuit抽芯 loose core光整平滑度 flatnessDrain cock 排气阀，放出开关Wrench 扳手Stopper 塞子，制动器Intensifier 增强器Check valve 止回阀Orifice 孔，口Pilot valve 领示阀，导阀Cold shut 冷疤，冷结Flow mark 波纹，流线谱Shot stroke 压射冲程Surge pressure 冲击压力，脉动压力Jack bolt 定位螺栓Anchor hole 锚栓孔Dust seal 档尘圈Valve cover 气门盖，阀盖Cylinder tube 汽缸筒Piston rod 活塞杆Piston ring 活塞环Shot cylinder 压射缸Wire clamp 钢丝钳Air hose 空气软管，送风管Atomizer 喷雾器Strainer 滤网Hollow shaft 空心轴，管轴Potentiometer 电位计，分压计Shaft 轴，杆状物Asbestos wire 石棉线Pulley 滑车，滑轮Spring washer 弹簧垫圈Inverter 电源交换器Cutting fluid 切削液refraction coefficient 折光系数Screw Cutting Tap 螺旋切削丝锥plug gauge 塞规color shade色泽red lead power 红丹粉stress relief 去应力casting film 铸型薄膜cast form铸造成形, 铸型cast house crane炉前[出铁场]吊车cast panel铸造面板cast rotor铸造转子cast superalloy铸造高温合金cast test block铸造试块[棒]casting character铸造性能casting crack缩裂casting fin铸件飞边, 铸件披缝, 铸件周缘翅片casting head浇冒口casting lap铸件皱纹casting scar铸疤, 浇注疤casting sealer铸件渗补剂casting strain铸造应变casting stress铸造应力spark plug 火花塞internal-combustion engine cylinder内燃机汽缸hydraulics 水力学pinion小齿轮pinion bearing小齿轮轴承pinion cage主动[行星]齿轮架, 差速器壳, 差速盘pinion cutting machine齿轴切削机床pinion head齿轴齿顶pinion shaped cutter插齿刀pinion spider差速器十字轴pinion stop(起动机的)齿轮停止器valve housing阀套valve actuating mechanism配气机构valve air relief自动放气阀valve bank阀组valve barrel阀缸valve body attachment阀体连接头valve bounce阀跳valve bush阀衬, 阀[衬]套valve chest gasket阀柜垫密片valve cock阀栓valve cottar气阀制销valve disc阀盘valve discharge centrifuge活门卸料式离心机valve follower阀推杆valve positioner阀门定位器分层Delaminationfilling-engine梳丝机器filling agent 填充剂;填料filling auger装载螺旋filling compoun填料filling funnel注液漏斗车架 (car) frame钣金 sheet metal测板 side plate内侧板Inner side plate焊钳soldering turret焊条 welding rod焊点 welding spot焊接机器人 welding robot寿命周期成本 life cycle cost前轴 fore/leading axle后翼子板 rear fender切削性能 cutting characteristic散热性能 heat dispersion耐磨性能 wear resistant property摩擦系数 friction coefficient灰铸铁 gray iron; graphitic cast iron过盈配合 tight/interference fit缸套 cylinder, sleeve, barrel tube pipe 导轨面 guide way (face)铣刀盘 face milling cutter/facing cutter 刀盘 tool pan/cutter head磨削余量 grinding allowance耐用性 endurance钝化 passivation刀尖圆弧 circular profile of knife point (刀具)主偏角 entering angle; plan angle 弹性变形量 amount of elastic deformation 燃烧室 combustion chamber磨屑 abrasive dust滤器芯 strainer core差速器 differential gear反冲减震器 recoiling shock absorber废气涡轮 exhaust turbine涡轮增压器 turbocharger增压盲区 turboloch喷油器 oil sprayer/atomizer汽化器 carburetor硬质合金刀具 carbide tipped tool精镗刀具 fine boring tool动力传动系统 power transmission system spanner 扳子 (美作:wrench)double-ended spanner 双头扳子adjustable spanner, monkey wrench 活扳子,活络扳手box spanner 管钳子 (美作:socket wrenchcalipers 卡规pincers, tongs 夹钳wire cutters 剪线钳multipurpose pliers, universal pliers 万能手钳adjustable pliers 可调手钳punch 冲子scraper 三角刮刀reamer 扩孔钻calliper gauge 孔径规hacksaw 钢锯grease gun 注油枪oil can 油壶边刨床 side planer插床 slotting machine车刀 lathe tool车轮车床 car wheel lathe车削 turningBayonet 卡口Bearing fittings 轴承配件Bearing processing equipment 轴承加工机Belt drive 带传动Bending machines 弯曲机Boring heads 搪孔头Boring machines 镗床Cable making tools 造线机CNC bending presses 电脑数控弯折机CNC boring machines 电脑数控镗床CNC drilling machines 电脑数控钻床CNC EDM wire-cutting machines 电脑数控电火花线切削机CNC electric discharge machines 电脑数控电火花机CNC engraving machines 电脑数控雕刻机CNC grinding machines 电脑数控磨床CNC lathes 电脑数控车床CNC machine tool fittings 电脑数控机床配件CNC milling machines 电脑数控铣床CNC shearing machines 电脑数控剪切机CNC toolings CNC刀杆CNC wire-cutting machines 电脑数控线切削机Conveying chains 输送链Crimping tools 卷边工具Disposable toolholder bits 舍弃式刀头Drawing machines 拔丝机Etching machines 蚀刻机Honing machines 搪磨机Lapping machines 精研机Milling heads 铣头Mold polishing/texturing 模具打磨/磨纹Planing machines 刨床aberration 色差atomization 雾化bank mark 料纹bite 咬入blacking hole 涂料孔(铸疵)blacking scab 涂料疤blister 起泡blooming 起霜blow hole 破孔blushing 泛白body wrinkle 侧壁皱纹breaking-in 冒口带肉bubble 膜泡burn mark 糊斑burr 毛边camber 翘曲cell 气泡centre buckle 表面中部波皱check 细裂痕checking 龟裂chipping 修整表面缺陷clamp-off 铸件凹痕collapse 塌陷colour mottle 色斑corrosion 腐蚀crazing 碎裂crazing 龟裂deformation 变形edge 切边碎片edge crack 裂边fading 退色filler speak 填充料斑fissure 裂纹flange wrinkle 凸缘起皱flaw 刮伤flow mark 流痕galling 毛边glazing 光滑gloss 光泽grease pits 污斑grinding defect 磨痕haircrack 发裂haze 雾度incrustation 水锈indentation 压痕internal porosity 内部气孔mismatch 偏模mottle 斑点necking 缩颈nick 割痕orange peel 橘皮状表面缺陷overflow 溢流peeling 剥离pit 坑pitting corrosion 点状腐蚀plate mark 模板印痕pock 麻点pock mark 痘斑resin streak 树脂流纹resin wear 树脂脱落riding 凹陷saponification 皂化scar 疤痕scrap jam 废料阻塞scratch 刮伤/划痕scuffing 深冲表面划伤seam 裂痕shock line 模口挤痕short shot 充填不足shrinkage pool 凹孔sink mark 凹痕skin inclusion 表皮折叠straightening 矫直streak 条状痕surface check 表面裂痕surface roughening 橘皮状表皮皱折surging 波动sweat out 冒汗torsion 扭曲warpage 翘曲waviness 波痕webbing 熔塌weld mark 焊痕whitening 白化wrinkle 皱纹表面处理关联用语时效硬化 age hardening气体硬化 air hardening空气韧化 air patterning退火 annealing阳极效应 anode effect阳极氧化处理 anodizing滚镀 barrel plating滚筒打光 barrel tumbling染黑法 blackening青熟脆性 blue shortness碳酸盐薄膜防锈法 bonderizing箱位退火 box annealing封箱渗碳 box carburizing辉面电镀 bright electroplating光辉热处理 bright heat treatment 旁路热处理 bypass heat treatment 化学电镀 chemical plating化学蒸镀 chemical vapor deposition 大气热处理 controlled atmosphere 锐角效应 corner effect儒缓放电 creeping discharge压花 embossing部分淬火 selective quenching。

压铸及机械英语词汇(2009-09-01 20:11:44)压铸及机械词汇A 安装尺寸 install dimension 凹模固定板 retainer plate凹模 female die, female mold, negative moldB 备件 spare parts变质 modification变质剂 modification agent扒渣 slagging-off保温炉 holding furnace保压压力 dwell pressure表面缺陷 surface defectC 淬火硬度quenching hardness抽芯core侧面抽芯side core抽芯油缸core oil cylinder插拔式结构plug抽芯机构core puller抽芯油缸支架bracket of cylinder粗糙度roughness/degree铸件表面粗糙度surface roughness擦伤galling尺寸公差dimension tolerance of casting除气degassing吹气净化blow purifying除气剂degassing flux出渣de-slagging出渣口slag hole沉渣sludge出炉口tap hole菜花头Cauli-flowering超声波检验ultrasonic test重熔re-meltingD 端盖cover动模垫块spacer parallel锻钢 forged steel氮化处理nitriding treatment断裂fracture塑性断裂plastic fracture导柱guide pillar导套guide sleeve导向板guide plate导向件guide part动型moving die/ejector die/movable mould动模座板moving clamp plate/bottom clamping plate 定模座板fixed clamp plate/top plate定型fixed die/cover die定模套版bolster/fixed die顶杆ejector pin顶出结构ejector mechanism顶出ejector吊装孔lifting eye吊环lifting ring镀钛处理titanium plating treatment多肉缺陷metallic projection电火花electric spark打磨grindingF 分流锥 divider/blast cone分型面 mold parting/parting face/mold joint附页 attachment/appendix复位杆 reset bar(rod)附件故障 accessory覆盖剂 covering flux废金属料scrap浮渣cinder反射炉 reverberatory furnace废品 reject飞边joint flash仿真simulationG 规格 specification/standard数值孔径 numerical aperture (N.A)固定段 segment坩埚crucible坩埚炉crucible furnace感应电炉electric induction furnace沟槽 blind scab硅SiliconH 滑块 sliding block滑块部件 moving parts滑块退让 return/move back焊补 welding-on横浇道 runner合模 die locking横流道 runner回炉料foundry returns合型 mold assembling/closing/die locking合型力 die locking force化学成分不合格chemical consistence analysisJ 浇口套 sprue bush浇排道系统pouring system浇不足 misrun浇注 pouring浇注断裂interrupted pour浇道比 gating ratio浇包 ladle精整dressing and finishing精度 accuracy接口 connector击伤 shot damage金相组织 metallographic structure金属残液heel金相检验metallographic test金属型涂料 die coating/coating for metal mold 加压速度 rate of pressure increasing间隙 clearance精炼refining精炼剂refining flux精密铸造 precision casting静置holding/stewing渗透 impregnation集渣装置dirt traps夹杂类缺陷inclusion defects夹渣entrapped slag/slag inclusion夹具 tool fixturesK 壳体 housing开炉 blowing in孔洞缺陷cavity库存 inventoryL 冷却 cooling冷却水管 cooling water pipe冷却耐压管 cooling pressure pipe冷却水管用密封圈 O-ring/sealing ring/gasket ring冷室卧式压铸机 horizontal (cold chamber) die casting machine 冷却系统 cooling system冷却水接口 cooling water connector冷裂 cold crack冷隔 cold lap铝 Aluminum裂纹 crack拉伤 caught casting拉杆孔 draw bar螺纹 screw/thread螺纹结构 screw structure螺纹公称直径(直径 diameter)公称尺寸(名义尺寸) specified size/nominal dimension漏油 leakage of oil棱边倒角 edge炉料 charge炉衬 furnace lining炉气分析flue gas analysis炉前分析on-the-spot sample analysis流痕 bloom/flow line力学性能不合格 physical-mechanical characteristic abnormalM 毛坯 rough/blank毛坯铸件 rough casting毛刺 veining/burr模芯 core模框 frame模槽 mold channel模套 chase/bolster/frame模具钢 die steel模具图纸 mold drawing内浇口 in-gate冒口 riser/feeder head冒口浇注系统 feeder head gating system镁 Magnesium锰 Manganese密闭耐压系统 tightness testN 内浇道 in-gate镍 NickleP 配油盘 pressure plate排气块 exhaust block排气槽 air vent排气孔 vent/venting channel排气塞 venting plug配合套圆形:fitting sleeve 方型: fitting case 跑铝 aluminum slop out of mold喷射冶金 injecting metallurgy喷丸清理 shot blasting cleaning抛丸清理 wheel blasting cleaning偏析 segregation破坏性实验 destructive testQ 取件机 extractor去除浇冒口 de-gating清铲 chipping缺陷铸件 defecting casting气孔 blowhole/gas cavity/pinhole/porosity气孔缩 blowhole shrinkage去毛刺 de-burring去除氧化皮 de-scaling氢 Hydrogen清理 cleaningR 热处理 heat treatment热电偶测温孔 thermocouple well热电偶 thermocouple (TC)/pyod热裂 hot heating熔炼 smelting熔化率 melting rate熔炼损耗 total melting loss熔池 bath熔剂 flux熔渣 slagS 水管 water pipe三维造型 3 D三坐标测量仪 coordinate 3上模座板 upper clamping plate缩孔 shrinkage缩松 dispersed shrinkage疏松 porosity(dispersed shrinkage)渗漏 leakage缩陷 sink/sink in/depression试块 test block/test piece/coupon实时控制系统 real-time control system 试模 de-buggingT 推板 push plate推杆 push rod推板导柱 push plate guide pillar推板导套 push plate guide sleeve凸模固定板 punch-retainer plate铜 copper钛 TitaniumW 网状裂纹 craze crack/crazing/checking 未浇满 poured shortX 型芯 core型腔 mold cavity镶拼处 splicing place斜导柱孔 hole of inclined guide pillar楔紧块 wedge型芯弯曲 core bending下模座板 lowering clamping plate型芯固定板 core-retainer plateX 光射线检验 X-ray inspectionY 压铸机 die casting machine压室 pressure chamber压室止口(定位)尺寸 dimension/size压实 squeezing compaction压射 shot/injection压射冲头 injection piston(ram)/plunger压铸型 die casting die压力铸造模具 die-casting die易损镶块 wear insert易损件 wearing parts预应力 pre-stress永久型 permanent mold硬点 hard spot溢流槽 over flow well印痕 indentation氧 Oxygen荧光检验 fluorescent testZ 真空接口 vacuum connector真空排气管 vacuum exhaust block总接头 main connector中接头 middle connector直浇道 sprue转接处(转口)transit装配图(铸型装配图) mold assembly drawing 铸钢 cast steel支架 ejector housing/mold base leg造渣 slag forming真空熔炼 vacuum melting真空压铸 vacuum die casting/ evacuated die casting 增压 pressurization针孔 pinhole沾铝 adhesive aluminum直读光谱分析仪 direct-reading spectrograph转运包 transfer ladle转向器steering rack柴油式传动叉车 Diesel forklift复印机 copying machine服务器 Server绘图仪 Graphic plotter兼容机 compatible machine材料库 warehouse投影仪 projector半自动车床 semi-automatic lathe半自动立式钻床 drill machine表面粗度测量仪 surface roughness gauge布洛维硬度计 Brinell hardness gauge测氢仪 Hydrogen gauge叉车充电机 charger程控交换机 exchanger齿轮油泵 oil pump储气罐 accumulator tank电动葫芦 Gantry crane电动试压泵 press tester电动斜切机 bias cutter电子秤 weighing scale电子扫描仪 scanner吊斗 spoon hopper高压离心风机 combustion blower管道泵 process water pump烘箱 oven监控系统 monitoring system简易数控车床 digital lathe交流弧焊机 Are welder抛光机 polisher锯床 saw空压机 air compressor冷冻式干燥机 dryer红外线测温仪冷却塔 cooling tower立式带锯床 band saw滤油机 oil filter焊接机 welder模温机 die heater喷粉室回收设备 painter system平面磨床 grinder气动量仪 air gauge切割机 cut-off machine清洗机 washer散热器攻丝机 tapping machine台式光谱仪 spectrograph台式砂轮机 abrasive machine卧式液压拉床 broaching machine铣床 milling machine钻床 drilling machine液压机 hydraulic machine真空机 vacuum pump时效炉 aging furnace电阻炉 stress relief furnace探伤机 diagnostic machine加工中心 machining center车床 lathe钻削中心 drilling & cutting center别克 Buick切边机 trim press冷却塔循环泵 cooling tower pump循环水离心泵 process water pump脱模剂压送机 die lube station取件机 extractorFL充痒压铸系统 FL oxygen feed die cast system 装卸车 loader在建工程 construction in progress捡漏机 picker纸芯式滤油器paper element filter电磁阀 solenoid valve溢流阀spillover valve调速阀 speed control valve压力传感器pressure transducer三角带wedge shaped belt节流阀throttle governor同步齿型带timing belt喷涂机spray coater轴承(main) bearing浮球阀 float valve/ball cock行车bridge crane平衡重式叉车counter balanced forklift轮毂螺栓wheel hub bolt制动蹄片brake shoe制动液braking fluid叶片lamina/vane侧护板side guard plate单列向心推力球轴承single row radial thrust ball bearing 带防尘盖单列轴承single row bearing shielded急停按钮 scram button三相开关threephase switch行程开关limit/travel switch断路器circuit breaker接触器 contactor中间继电器intermediate relay时间继电器 time relay控制变压器control transformer开关电源switching supply节能灯energy-saving lamp日光灯管fluorescent tube自整流高压汞灯泡self-rectifying high pressure mercury lamp 电工胶布garrers/electrical tape焊条welding rod石笔slate pencil外圆磨床external grinderHydraulic fluid oil 液压油Safety hook/bolts 安全钩Crosshead 十字头Tail stock 尾架尾座Frame cover 护板框盖Toggle top cover 肘环顶Coupling 联轴器Tie-bar 拉杆, 系杆Control panel 控制面板Power board 分配板, 配电板Overhauling 大修, 拆修Hose 软管, 水龙带Warranty period 保修期Nozzle 管口, 喷嘴Nature tan 日晒后的颜色, 茶色Electric fitting 电装、Rubber pad 橡胶垫Shock absorbing rubber stopper 减震橡皮塞Die height 模子闭合高度Die stroke 动模行程Intensification ratio standard 增强比标准Plunger stroke 柱塞行程Plunger tip penetration 冲头穿透力Viscosity index 粘度指数Rated pressure 额定压力Plug socket 插口, 塞孔Ventilated 通风的Anchor bolt hole 地锚(脚)螺栓孔Inlet 入口Galvanize 通电流Carbon grain 碳粒Mortar 火泥, 砂浆Stretcher 拉伸机Earthing cable 接地电缆Manifold 总管, 集合管Clamp force sensor 夹紧力传感器Attenuate 削弱Emulsification 乳化作用中子线wire for sliding出模斜度 draft angle隔皮 bur掉肉 misrun研配 grindTurbidity 浑浊度Refract meter 折光仪Sediment 沉淀物Glycol 乙二醇Combustible 易燃的Water-soluble 水溶性的Grease pump 黄油泵，油脂泵Drooling 滴料Disulfide 二硫化物Lithium 锂Gauge cock 试水位旋塞Pressure match valve 压力拟合阀Lock/check nut 防松螺母Slant 倾斜Core sliding face 型芯滑面Flux treatment 熔剂处理Die clamping cylinder 模具夹紧气缸Clogging 堵塞，闭合Electrode bar 电极棒Fumigation certificate 熏蒸消毒证书Crate 条板箱，柳条箱Resin parts 树脂零件Oil ring 油环Gear box 齿轮箱，传动箱,变速箱Draft angle 出模斜度Tap and drill gauge 丝锥及钻头规Tap borer 螺纹底孔钻Tap cutter 丝锥刀具Tap die holder 丝锥板牙两用夹头Tap handle 丝锥扳手Screw funnel 分液漏斗Screw chasing machine 螺纹切削机Screw cutting 螺纹切削Screw pitch gauge 螺距规Screw rivet 螺纹铆钉Screw vent 螺杆通孔Rack housing 齿条罩Rack Tubes 油缸Cup Seals Feed Pipes 输油管Spools 卷轴Recuperating Seal(恢复性密封) Inflator Tubes 充气.Cut Seals Steering Hoses 转向胶管Biscuit thickness 料柄厚度注油孔 oil filter point牛皮纸 kraft/brown paper瓦楞纸 fluting paper崩料 charge downslide/collapse 卡涉现象 interference phenomenon 机械加工余量 stocking复制模 replaced mould偏心距 offset distance抽大缸 pull tie bar料头 biscuit抽芯 loose core光整平滑度 flatnessDrain cock 排气阀，放出开关Wrench 扳手Stopper 塞子，制动器Intensifier 增强器Check valve 止回阀Orifice 孔，口Pilot valve 领示阀，导阀Cold shut 冷疤，冷结Flow mark 波纹，流线谱Shot stroke 压射冲程Surge pressure 冲击压力，脉动压力Jack bolt 定位螺栓Anchor hole 锚栓孔Dust seal 档尘圈Valve cover 气门盖，阀盖Cylinder tube 汽缸筒Piston rod 活塞杆Piston ring 活塞环Shot cylinder 压射缸Wire clamp 钢丝钳Air hose 空气软管，送风管Atomizer 喷雾器Strainer 滤网Hollow shaft 空心轴，管轴Potentiometer 电位计，分压计Shaft 轴，杆状物Asbestos wire 石棉线Pulley 滑车，滑轮Spring washer 弹簧垫圈Inverter 电源交换器Cutting fluid 切削液refraction coefficient 折光系数Screw Cutting Tap 螺旋切削丝锥plug gauge 塞规color shade色泽red lead power 红丹粉stress relief 去应力casting film 铸型薄膜cast form铸造成形, 铸型cast house crane炉前[出铁场]吊车cast panel铸造面板cast rotor铸造转子cast superalloy铸造高温合金cast test block铸造试块[棒]casting character铸造性能casting crack缩裂casting fin铸件飞边, 铸件披缝, 铸件周缘翅片casting head浇冒口casting lap铸件皱纹casting scar铸疤, 浇注疤casting sealer铸件渗补剂casting strain铸造应变casting stress铸造应力spark plug 火花塞internal-combustion engine cylinder内燃机汽缸hydraulics 水力学pinion小齿轮pinion bearing小齿轮轴承pinion cage主动[行星]齿轮架, 差速器壳, 差速盘pinion cutting machine齿轴切削机床pinion head齿轴齿顶pinion shaped cutter插齿刀pinion spider差速器十字轴pinion stop(起动机的)齿轮停止器valve housing阀套valve actuating mechanism配气机构valve air relief自动放气阀valve bank阀组valve barrel阀缸valve body attachment阀体连接头valve bounce阀跳valve bush阀衬, 阀[衬]套valve chest gasket阀柜垫密片valve cock阀栓valve cottar气阀制销valve disc阀盘valve discharge centrifuge活门卸料式离心机valve follower阀推杆valve positioner阀门定位器分层Delaminationfilling-engine梳丝机器filling agent 填充剂;填料filling auger装载螺旋filling compoun填料filling funnel注液漏斗车架 (car) frame钣金 sheet metal测板 side plate内侧板Inner side plate焊钳soldering turret焊条 welding rod焊点 welding spot焊接机器人 welding robot寿命周期成本 life cycle cost前轴 fore/leading axle后翼子板 rear fender切削性能 cutting characteristic散热性能 heat dispersion耐磨性能 wear resistant property摩擦系数 friction coefficient灰铸铁 gray iron; graphitic cast iron过盈配合 tight/interference fit缸套 cylinder, sleeve, barrel tube pipe 导轨面 guide way (face)铣刀盘 face milling cutter/facing cutter 刀盘 tool pan/cutter head磨削余量 grinding allowance耐用性 endurance钝化 passivation刀尖圆弧 circular profile of knife point (刀具)主偏角 entering angle; plan angle 弹性变形量 amount of elastic deformation 燃烧室 combustion chamber磨屑 abrasive dust滤器芯 strainer core差速器 differential gear反冲减震器 recoiling shock absorber废气涡轮 exhaust turbine涡轮增压器 turbocharger增压盲区 turboloch喷油器 oil sprayer/atomizer汽化器 carburetor硬质合金刀具 carbide tipped tool精镗刀具 fine boring tool动力传动系统 power transmission system spanner 扳子 (美作:wrench)double-ended spanner 双头扳子adjustable spanner, monkey wrench 活扳子,活络扳手box spanner 管钳子 (美作:socket wrenchcalipers 卡规pincers, tongs 夹钳wire cutters 剪线钳multipurpose pliers, universal pliers 万能手钳adjustable pliers 可调手钳punch 冲子scraper 三角刮刀reamer 扩孔钻calliper gauge 孔径规hacksaw 钢锯grease gun 注油枪oil can 油壶边刨床 side planer插床 slotting machine车刀 lathe tool车轮车床 car wheel lathe车削 turningBayonet 卡口Bearing fittings 轴承配件Bearing processing equipment 轴承加工机Belt drive 带传动Bending machines 弯曲机Boring heads 搪孔头Boring machines 镗床Cable making tools 造线机CNC bending presses 电脑数控弯折机CNC boring machines 电脑数控镗床CNC drilling machines 电脑数控钻床CNC EDM wire-cutting machines 电脑数控电火花线切削机CNC electric discharge machines 电脑数控电火花机CNC engraving machines 电脑数控雕刻机CNC grinding machines 电脑数控磨床CNC lathes 电脑数控车床CNC machine tool fittings 电脑数控机床配件CNC milling machines 电脑数控铣床CNC shearing machines 电脑数控剪切机CNC toolings CNC刀杆CNC wire-cutting machines 电脑数控线切削机Conveying chains 输送链Crimping tools 卷边工具Disposable toolholder bits 舍弃式刀头Drawing machines 拔丝机Etching machines 蚀刻机Honing machines 搪磨机Lapping machines 精研机Milling heads 铣头Mold polishing/texturing 模具打磨/磨纹Planing machines 刨床aberration 色差atomization 雾化bank mark 料纹bite 咬入blacking hole 涂料孔(铸疵)blacking scab 涂料疤blister 起泡blooming 起霜blow hole 破孔blushing 泛白body wrinkle 侧壁皱纹breaking-in 冒口带肉bubble 膜泡burn mark 糊斑burr 毛边camber 翘曲cell 气泡centre buckle 表面中部波皱check 细裂痕checking 龟裂chipping 修整表面缺陷clamp-off 铸件凹痕collapse 塌陷colour mottle 色斑corrosion 腐蚀crack 裂痕crazing 碎裂crazing 龟裂deformation 变形edge 切边碎片edge crack 裂边fading 退色filler speak 填充料斑fissure 裂纹flange wrinkle 凸缘起皱flaw 刮伤flow mark 流痕galling 毛边glazing 光滑gloss 光泽grease pits 污斑grinding defect 磨痕haircrack 发裂haze 雾度incrustation 水锈indentation 压痕internal porosity 内部气孔mismatch 偏模mottle 斑点necking 缩颈nick 割痕orange peel 橘皮状表面缺陷overflow 溢流peeling 剥离pit 坑pitting corrosion 点状腐蚀plate mark 模板印痕pock 麻点pock mark 痘斑resin streak 树脂流纹resin wear 树脂脱落riding 凹陷sagging 松垂saponification 皂化scar 疤痕scrap jam 废料阻塞scratch 刮伤/划痕scuffing 深冲表面划伤seam 裂痕shock line 模口挤痕short shot 充填不足shrinkage pool 凹孔sink mark 凹痕skin inclusion 表皮折叠straightening 矫直streak 条状痕surface check 表面裂痕surface roughening 橘皮状表皮皱折surging 波动sweat out 冒汗torsion 扭曲warpage 翘曲waviness 波痕webbing 熔塌weld mark 焊痕whitening 白化wrinkle 皱纹表面处理关联用语时效硬化 age hardening气体硬化 air hardening空气韧化 air patterning退火 annealing阳极效应 anode effect阳极氧化处理 anodizing滚镀 barrel plating滚筒打光 barrel tumbling染黑法 blackening青熟脆性 blue shortness碳酸盐薄膜防锈法 bonderizing箱位退火 box annealing封箱渗碳 box carburizing辉面电镀 bright electroplating光辉热处理 bright heat treatment 旁路热处理 bypass heat treatment 化学电镀 chemical plating化学蒸镀 chemical vapor deposition 大气热处理 controlled atmosphere 锐角效应 corner effect儒缓放电 creeping discharge压花 embossing部分淬火 selective quenching。

文案大全Assembly line 组装线 Layout 布置图Conveyer 流水线物料板 Rivet table 拉钉机 Rivet gun 拉钉枪 Screw driver 起子Electric screw driver 电动起子 Pneumatic screw driver 气动起子 worktable 工作桌 OOBA 开箱检查fit together 组装在一起 fasten 锁紧(螺丝) fixture 夹具(治具) pallet 栈板 barcode 条码barcode scanner 条码扫描器 fuse together 熔合 fuse machine 热熔机 repair 修理 operator 作业员 QC 品管supervisor 课长 ME 制造工程师 MT 制造生技cosmetic inspect 外观检查 inner parts inspect 内部检查 thumb screw 大头螺丝 lbs. inch 镑、英寸front plate 前板traightener 整平机punching machine 冲床 robot 机械手 hydraulic 液压 rear plate 后板 chassis 基座 bezel panel 面板power button 电源按键 reset button 重置键Hi-pot test of SPS 高源高压测试 Voltage switch of SPS 电源电压接拉键sheet metal parts 冲件 plastic parts 塑胶件 SOP 制造作业程序material check list 物料检查表 work cell 工作间 trolley 台车 carton 纸箱 sub-line 支线 left fork 叉车personnel resource department 人力资源部production department 生产部门 planning department 企划部 QC Section 品管科stamping factory 冲压厂 painting factory 烤漆厂 common equipment 常用设备 uncoiler and s machine 油压机 lathe 车床planer |'plein|刨床 miller 铣床 grinder 磨床 driller??床linear cutting 线切割 electrical sparkle 电火花 welder 电焊机staker=reviting machine 铆合机 position 职务 president 董事长general manager 总经理special assistant manager 特助 factory director 厂长 department director 部长deputy manager | =vice manager 副理section supervisor 课长deputy section supervisor =vice section superisor 副课长 group leader/supervisor 组长 line supervisor 线长 assistant manager 助理to move, to carry, to handle 搬运 be put in storage 入库 pack packing 包装 to apply oil 擦油 final inspection 终检 to connect material 接料 to reverse material 翻料 wet station 沾湿台 Tiana 天那水cleaning cloth 抹布 tname of a department 部门名称 a o load material 上料 to unload material 卸料to return material/stock to 退料 scraped |'skræpid|报废 scrape ..v.刮;削deficient purchase 来料不良 manufacture procedure 制程 deficient manufacturing procedure 制程不良oxidation |' ksi'dein|氧化scratch 刮伤 dents 压痕defective upsiding down 抽芽不良 defective to staking 铆合不良 embedded lump 镶块feeding is not in place 送料不到位stamping-missing 漏冲production capacity 生产力 education and training 教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓 dministration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单screwdriver holder起子插座pedal踩踏板stopper阻挡器flow board流水板hydraulic handjack油压板车forklift叉车pallet栈板glove(s)手套glove(s) with exposed fingers割手套thumb大拇指forefinger食指midfinger中指ring finger无名指little finger小指band-aid创可贴iudustrial alcohol工业酒精alcohol container沾湿台head of screwdriver起子头sweeper扫把mop拖把vaccum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋chain链条jack升降机production line流水线chain链条槽magnetizer加磁器lamp holder灯架to mop the floor拖地to clean the floor扫地to clean a table擦桌子air pipe 气管packaging tool打包机packaging打包missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a little bigger尺寸偏大(小)cosmetic defect外观不良slipped screwhead/slippery screwhead螺丝滑头slipped screwhead/shippery screwthread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色scratch划伤poor processing 制程不良poor incoming part事件不良fold of pakaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍polishing/surface processing表面处理exposed metal/bare metal金属裸露lack of painting烤漆不到位safety安全quality品质delivery deadline交货期cost成本engineering工程die repair模修enterprise plan = enterpriseexpansion projects企划QC品管die worker模工production, to produce生产equipment设备to start a press开机stop/switch off a press关机classification整理regulation整顿cleanness清扫conservation清洁culture教养qualified products, up-to-gradeproducts良品defective products, notup-to-grade products不良品waste废料board看板feeder送料机sliding rack滑料架defective product box不良品箱die change 换模文案大全to fix a die装模to take apart a die拆模to repair a die修模packing material包材basket蝴蝶竺plastic basket胶筐isolating plate baffle plate; barricade隔板carton box纸箱to pull and stretch拉深to put material in place, to cut material, to input落料to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料transportation运输(be)qualfied, up to grade合格not up to grade, not qualified 不合格material change, stock change材料变更feature change 特性变更evaluation评估prepare for, make preparations for 准备parameters参数rotating speed, revolution转速manufacture management制造管理abnormal handling异常处理production unit生产单位lots of production生产批量steel plate钢板roll material卷料manufacture procedure制程operation procedure作业流程to revise, modify修订to switch over to, switch---tothrow--over switching over切换engineering, project difficulty工程瓶颈stage die工程模automation自动化to stake, staking, reviting铆合add lubricating oil加润滑油shut die架模shut height of a die架模高度analog-mode device类模器die lifter举模器argon welding氩焊vocabulary for stamping冲压常词汇stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener整平机feeder送料机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece,block stop 定位块reset复位smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货to return delivenry to.to send delinery backto retrn of goods退货registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收to notice通知application form for purchase请购单consume, consumption消耗to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked断裂to lubricate润滑common vocabulary for dieengineering模具工程常用词汇die 模具文案大全figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die 连续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap 切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder文件夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备waste materials废料work in progress product在制品casing = containerazation装箱quantity of physical invetorysecond count 复盘点数量quantity of customs count会计师盘,点数量the first page第一联filed by accounting departmentfor reference会计部存查end-user/using unit(department)使用单位summary of year-end physicalinventory bills年终盘点截止单据汇总表bill name单据名称This sheet and physical inventorylist will be sent to accountingdepartment together (Those of NHKwill be sent to financialdepartment)本表请与盘点清册一起送会计部－(NHK厂区送财会部)Application status records ofyear-end physical inventory Listandphysical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO.空白与作废单号plate电镀mold成型material for engineering moldtesting工程试模材料not included in physicalinventory不列入盘点sample样品incoming material to be inspected进货待验description品名steel/rolled steel钢材material statistics sheet物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点chairman主席present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by /prepared by核准/审核/承办PCE assembly production schedulesheetPCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked待验或重工total合计cause description原因说明文案大全part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts 不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆文案大全edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕??shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸)draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号)shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）文案大全top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相关英文compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具移转成型用模具encapsulation molding低压封装成型射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道h=0.02~0.05mmw=3.2mmL=3~5mmwelding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆)slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口文案大全H=F=1/2t~1/5tT=2.5~3.5mmdiaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Φ0.8~1.0mmRunner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣品质人员名称类QC quality control 品质管理人员FQC final quality control 终点品质管制人员IPQC in process quality control 制程中的品质管制人员OQC output quality control 最终出货品质管制人员IQC incoming quality control 进料品质管制人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance出货质量保证人员QE quality engineering 品质工程人员品质保证类FAI first article inspection新品首件检查FAA first article assurance 首件确认TVR tool verification report模具确认报告3B 3B 模具正式投产前确认CP capability index 能力指数CPK capability index of process模具制程能力参数SSQA standardized supplierquality 合格供应商品质评估OOBA out of box audit 开箱检查QFD quality function deployment品质机能展开FMEA failure modeleffectiveness analysis 失效模式分析8 disciplines 8项回复内容FA final audit 最後一次稽核CAR corrective action request改正行动要求corrective action report 改正行动报告FQC运作类AQL Acceptable Quality Level运作类允收品质水准S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的AOQ Average Output Quality 平均出厂品质AOQL Average Output QualityLevel 平均出厂品质Q/R/SQuality/Reliability/Service 品质/可靠度服务MIL-STD Military-Standard 军用标准S I-S IV Special I-Special IV特殊抽样水准等级P/N Part Number 料号L/N Lot Number 特采AOD Accept On Deviation 特采UAI Use As It 首件检查报告FPIR First Piece InspectionReport 百万分之一PPM Percent Per Million 批号制程统计品管专类SPC Statistical Process Control统计制程管制SQC Statistical Quality Control统计品质管制R Range 全距AR Averary Range 全距平均值UCL Upper Central Limit 管制上限LCL Lower Central Limit 管制下限MAX Maximum 最大值MIN Minimum 最小值GRR GaugeReproducibility&Repeatability量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径FREQ Frequency 频率N Number 样品数其它品质术语类QCC Quality Control Circle 品质圈QIT Quality Improvement Team品质改善小组PDCA Plan Do Check Action 计划执行检查总结ZD Zero Defect 零缺点QI Quality Improvement 品质改善QP Quality Policy 目标方针TQM Total Quality Management文案大全全面品质管理MRB Material Reject Bill 退货单LQL Limiting Quality Level 最低品质水准RMA Return Material Audit 退料认可QAN Quality Amelionrate Notice 品质改善活动ADM Absolute Dimension Measuremat 全尺寸测量QT Quality Target 品质目标7QCTools 7 Quality Controll Tools 品管七大手法通用之件类ECN Engineering Change Notes 工程变更通知(供应商)ECO Engineering Change Order 工程改动要求(客户)PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Specification In Process 制程检验规格SOP Standard Operation Procedure 制造作业规范IS Inspection Specification 成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类QC Quality System 品质系统ES Engineering Standarization工程标准CGOO China General PCE龙华厂文件H Huston (美国)休斯敦C Compaq (美国)康伯公司C China 中国大陆A Assembly 组装(厂)S Stamping 冲压(厂)P Painting 烤漆(厂)I Intel 英特尔公司T TAIWAN 台湾IWS International WorkmanStandard 工艺标准ISO International StandardOrganization 国际标准化组织GS General Specification 一般规格CMCS C-China M-ManufactC-Compaq S-Stamping Compaq产品在龙华冲压厂制造作业规范CQCA Q-Quality A-AssemblyCompaq产品在龙华组装厂品管作业规范CQCP P-Painting Compaq产品在龙华烤漆厂品管作业规范部类PMC Production & MaterialControl 生产和物料控制PPC Production Plan Control 生产计划控制MC Material Control 物料控制ME Manafacture Engineering 制造工程部PE Project Engineering 产品工程部A/C Accountant Dept 会计部P/A Personal & Administration人事行政部DC Document Center 资料中心QE Quality Engineering 品质工程(部)QA Quality Assurance 品质保证(处)QC Quality Control 品质管制(课)PD Product Department 生产部LAB Labratry 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部P Painting 烤漆(厂)A Asssembly 组装(厂)S Stamping 冲压(厂)生产类PCS Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供应商)识别码SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号其它OEM Original EquipmentManufacture 原设备制造PCE Personal Computer Enclosure个人电脑外设PC Personal Computer 个人电脑CPU Central Processing Unit 中央处理器SECC SECC` 电解片SGCC SGCC 热浸镀锌材料NHK North of Hongkong 中国大陆PRC People's Republic of China中国大陆U.S.A the United States ofAmerica 美国文案大全A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量VS 以及REV Revision 版本JIT Just In Time 零库存I/O Input/Output 输入/输出OK Ok 好NG Not Good 不行,不合格C=0 Critical=0 极严重不允许ESD Electry-static Discharge 静电排放5S 希腊语整理,整顿,清扫,清洁,教养ATIN Attention 知会CC Carbon Copy 副本复印相关人员APP Approve 核准,认可,承认CHK Check 确认AM Ante Meridian 上午PM Post Meridian 下午CD Compact Disk 光碟CD-ROM Compact Disk Read-Only Memory 只读光碟FDD Floppy Disk Drive 软碟机HDD Hard Disk Drive 碟碟机REF Reference 仅供参考CONN Connector 连接器CAV Cavity 模穴CAD Computer Aid Design 计算机辅助设计ASS'Y Assembly 装配,组装MAT'S Material 材料IC Integrated Circuit 集成电路T/P True Position 真位度TYP Type 类型WDR Weekly Delivery Requitement周出货需求C?T Cycle Time 制程周期L/T Lead Time 前置时间(生产前准备时间)S/T Standard Time 标准时间P/M Product Market 产品市场3CComputer,Commumcation,Consumerelectronic's 消费性电子5WIHWhen,Where,Who,What,Why,How to5MMan,Machine,Material,Method,Measurement4MIHMan,Materia,Money,Method,Time人力,物力,财务,技术,时间(资源)SQA Strategy Quality Assurance策略品质保证DQA Desigh Quality Assurance设计品质保证MQA Manufacture QualityAssurance 制造品质保证SSQA Sales and service QualityAssurance 销售及服务品质保证LRR Lot Rejeet Rate 批退率BS Brain storming 脑力激荡EMI Electronic MagnetionInspect 高磁测试FMI Frequency Modulatim Inspect高频测试B/M Boar/Molding(flat cable)C/P Connector of PCA/P AssemblySPS Switching power supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital Vedio DiskVCD Vdeio Compact DiskLCD Liquid Crystal DisplayCAD Computer AID DesignCAM Computer AID ManufacturingCAE Computer AID EngineeringABIOS Achanced Basic input/output system 先进的基本输入/输出系统CMOS Complemeruary Metoll OxideSemiconductor 互补金属氧化物半导体PDA Personal Digital Assistant个人数字助理IC Integrated Circuit 集成电路ISA Industry StandardArchitecture 工业标准体制结构MCA Micro Channel Architecture微通道结构EISA Extended Industry StandardArchitecture 扩充的工业标准结构SIMM Single in-line memorymodule 单项导通汇流组件DIMM Dual in-line Memory Module双项导通汇流组件LED Light-Emitting Diode 发光二级管FMEA Failure Mode Effectivenes失效模式分析W/H Wire Harness 金属线绪束集组件F/C Flat Calle 排线PCB Printed Circuit Board 印刷电路板CAR Correction Action Report改善报告NG Not Good 不良WPR Weekly Delivery Requirement周出货要求PPM Parts Per Million 百万分之一文案大全TPM Total Production Maintenance 全面生产保养MRP Material Requiremcnt Planning 物料需计划OC Operation System 作业系统TBA To Be Design 待定,定缺D/C Drawing ChangeP/P Plans & ProceduneEMI Electrical-Music Industry 电子音乐工业RFI Read Frequency Input 读频输入MMC Maximum Material Condition MMS Maximum Material SizeLMC Least Material Condition LMS Least Material Size模具技术用语各种模具常用成形方式accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸 precision forging 精密锻造cold forging 冷锻 press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形 rotaryforging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形 rubber molding橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形 shellcasting 壳模铸造foam forming ?泡成形sinterforging 烧结锻造forging roll 轧锻six sidesforging 六面锻造gravity casting 重力铸造slushmolding 凝塑成形hollow(blow) molding 中空(吹出)成形 squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfermolding 转送成形injection molding 射出成形 warmforging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模landedplunger mold 有肩柱塞式模具burnishing die 挤光模landedpositive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模 loose mold活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具 manifolddie 分歧管模具counter punch 反凸模modularmold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswtbending die 双折冷弯模具extrusion die 挤出模 palletizingdie 叠层模family mold 反套制品模具 plastermold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具 pressuredie 压紧模fishtail die 鱼尾形模具 profiledie 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protablemold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具 sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavitymold 单腔模具solid forging die 整体锻模 splitforging die 拼合锻模split mold 双并式模具 spruelessmold 无注道残料模具squeezing die 挤压模stretch文案大全form die 拉伸成形模sweeping mold 平刮铸模 swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具 universal mold 通用模具unscrewing mold 退扣式模具 yoke type die 轭型模模具厂常用之标准零配件air vent vale 通气阀 anchor pin 锚梢angular pin 角梢 baffle 调节阻板angular pin 倾斜梢 baffle plate 折流档板ball button 球塞套 ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下模板 bottom board 浇注底板bolster 垫板 bottom plate 下固定板bracket 托架 bumper block 缓冲块buster 堵口 casting ladle 浇注包casting lug 铸耳 cavity 模穴(模仁) cavity retainer plate 模穴托板center pin 中心梢clamping block 锁定块coilspring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型 core pin 心型梢cotter 开口梢 cross 十字接头cushion pin 缓冲梢diaphragmgate 盘形浇口die approach 模头料道 die bed 型底die block 块形模体 die body 铸模座die bush 合模衬套 die button 冲模母模die clamper 夹模器 die fastener模具固定用零件die holder 母模固定板 die lip 模唇die plate 冲模板 die set 冲压模座direct gate 直接浇口 dog chuck爪牙夹头dowel 定位梢 dowel hole 导套孔dowel pin 合模梢 dozzle 辅助浇口dowel pin 定位梢 draft 拔模锥度draw bead 张力调整杆drivebearing 传动轴承ejection pad 顶出衬垫 ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫 ejector pin顶出梢ejector plate 顶出板 ejector rod顶出杆ejector sleeve 顶出衬套 ejectorvalve 顶出阀eye bolt 环首螺栓 filling core椿入蕊film gate 薄膜形浇口 finger pin指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘?flash gate 毛边形浇口 flask 上箱floating punch 浮动冲头 gate 浇口gate land 浇口面 gib 凹形拉紧?goose neck 鹅颈管 guide bushing引导衬套guide pin 导梢 guide post 引导柱guide plate 导板 guide rail 导轨head punch 顶?冲头headlesspunch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injectionram 压射柱塞inlay busher 嵌入衬套innerplunger 内柱塞inner punch 内冲头 insert 嵌件insert pin 嵌件梢 king pin 转向梢king pin bush 主梢衬套 knockoutbar 脱模杵land 合模平坦面 land area 合模面leader busher 导梢衬套liftingpin 起模顶?lining 内衬locating centerpunch 定位中心冲头locating pilot pin 定位导梢locating ring 定位环lock block 压块 locking block 定位块locking plate 定位板 loose bush活动衬套making die 打印冲子manifoldblock 歧管档块master plate 靠模样板matchplate 分型板mold base 塑胶模座 mold clamp 铸模紧固夹mold platen 模用板movingbolster 换模保持装置moving bolster plate 可动侧模板文案大全。

精心整理压铸及机械英语词汇(2009-09-0120:11:44)压铸及机械词汇A 安装尺寸installdimension凹模固定板retainerplate凹模femaledie,femalemold,negativemoldB 备件变质变质剂扒渣保温炉保压压力表面缺陷C 抽芯侧面抽芯sidecore抽芯油缸coreoilcylinder插拔式结构plug抽芯机构corepuller抽芯油缸支架bracketofcylinder粗糙度roughness/degree铸件表面粗糙度surfaceroughness擦伤galling尺寸公差dimensiontoleranceofcasting 除气degassing吹气净化blowpurifying除气剂degassingflux出渣出渣口沉渣出炉口菜花头重熔D端盖动模垫块锻钢氮化处理nitridingtreatment断裂fracture塑性断裂plasticfracture导柱guidepillar导套guidesleeve导向板guideplate导向件guidepart动型movingdie/ejectordie/movablemould动模座板movingclampplate/bottomclampingplate 定模座板fixedclampplate/topplate定型fixeddie/coverdie定模套版bolster/fixeddie顶杆顶出结构顶出吊装孔吊环镀钛处理多肉缺陷电火花打磨F分流锥分型面附页attachment/appendix复位杆resetbar(rod)附件故障accessory覆盖剂coveringflux废金属料scrap浮渣cinder反射炉reverberatoryfurnace废品reject飞边jointflash仿真simulationG规格specification/standard数值孔径固定段坩埚坩埚炉感应电炉沟槽硅H滑块滑块部件滑块退让焊补welding-on横浇道runner合模dielocking横流道runner回炉料foundryreturns合型moldassembling/closing/dielocking合型力dielockingforce化学成分不合格chemicalconsistenceanalysisJ浇口套spruebush浇排道系统pouringsystem浇不足misrun浇注浇注断裂浇道比浇包精整精度接口击伤金相组织金属残液金相检验金属型涂料diecoating/coatingformetalmold 加压速度rateofpressureincreasing间隙clearance精炼refining精炼剂refiningflux精密铸造precisioncasting静置holding/stewing渗透impregnation集渣装置dirttraps夹杂类缺陷inclusiondefects夹渣entrappedslag/slaginclusion 夹具toolfixturesK壳体开炉孔洞缺陷库存L冷却冷却水管冷却系统冷却水接口coolingwaterconnector 冷裂coldcrack冷隔coldlap铝Aluminum裂纹crack拉伤caughtcasting拉杆孔drawbar螺纹screw/thread螺纹结构screwstructure螺纹公称直径(直径diameter)公称尺寸(名义尺寸)specifiedsize/nominaldimension 漏油leakageofoil棱边倒角炉料炉衬炉气分析炉前分析流痕M毛坯毛坯铸件毛刺模芯core模框frame模槽moldchannel模套chase/bolster/frame模具钢diesteel模具图纸molddrawing内浇口in-gate冒口riser/feederhead冒口浇注系统feederheadgatingsystem 镁Magnesium锰Manganese密闭耐压系统tightnesstestN内浇道镍P配油盘排气块排气槽排气孔排气塞跑铝喷射冶金injectingmetallurgy喷丸清理shotblastingcleaning抛丸清理wheelblastingcleaning偏析segregation破坏性实验destructivetestQ取件机extractor去除浇冒口de-gating清铲chipping缺陷铸件defectingcasting气孔blowhole/gascavity/pinhole/porosity 气孔缩blowholeshrinkage去毛刺de-burring氢清理R热处理热电偶热裂熔炼熔化率熔池bath熔剂flux熔渣slagS水管waterpipe三维造型3D三坐标测量仪coordinate3上模座板upperclampingplate缩孔shrinkage缩松dispersedshrinkage疏松porosity(dispersedshrinkage)渗漏leakage缩陷试块试模T推板推杆铜钛W网状裂纹crazecrack/crazing/checking 未浇满pouredshortX型芯core型腔moldcavity镶拼处splicingplace斜导柱孔holeofinclinedguidepillar 楔紧块wedge型芯弯曲corebending下模座板loweringclampingplate型芯固定板core-retainerplateX光射线检验X-rayinspectionY压铸机压室压实压射压铸型易损件预应力永久型permanentmold硬点hardspot溢流槽overflowwell印痕indentation氧Oxygen荧光检验fluorescenttestZ真空接口vacuumconnector真空排气管vacuumexhaustblock 总接头mainconnector中接头middleconnector直浇道sprue转接处(转口)transit装配图铸钢支架造渣增压针孔沾铝转运包转向器steeringrack柴油式传动叉车Dieselforklift 复印机copyingmachine服务器Server绘图仪Graphicplotter兼容机compatiblemachine材料库warehouse投影仪projector半自动车床semi-automaticlathe半自动立式钻床drillmachine表面粗度测量仪surfaceroughnessgauge 布洛维硬度计Brinellhardnessgauge测氢仪齿轮油泵储气罐电动葫芦电子秤吊斗高压离心风机combustionblower管道泵processwaterpump烘箱oven监控系统monitoringsystem简易数控车床digitallathe交流弧焊机Arewelder抛光机polisher锯床saw空压机aircompressor冷冻式干燥机dryer红外线测温仪冷却塔coolingtower滤油机焊接机模温机平面磨床气动量仪切割机清洗机台式砂轮机abrasivemachine卧式液压拉床broachingmachine 铣床millingmachine钻床drillingmachine液压机hydraulicmachine真空机vacuumpump时效炉agingfurnace电阻炉stressrelieffurnace探伤机diagnosticmachine加工中心machiningcenter车床lathe钻削中心drilling&cuttingcenter别克切边机取件机FL装卸车在建工程捡漏机电磁阀solenoid??valve溢流阀spillovervalve调速阀speedcontrolvalve压力传感器pressuretransducer 三角带wedgeshapedbelt节流阀throttlegovernor同步齿型带timingbelt喷涂机spraycoater轴承(main)bearing浮球阀floatvalve/ballcock行车bridgecrane平衡重式叉车counterbalancedforklift轮毂螺栓制动蹄片制动液叶片侧护板急停按钮三相开关行程开关断路器接触器contactor中间继电器intermediaterelay时间继电器timerelay控制变压器controltransformer开关电源switchingsupply节能灯energy-savinglamp日光灯管fluorescenttube自整流高压汞灯泡self-rectifyinghighpressuremercurylamp 电工胶布garrers/electricaltape焊条weldingrod石笔slatepencil外圆磨床externalgrinderCouplingTie-barHose软管,水龙带Warrantyperiod保修期Nozzle管口,喷嘴Naturetan日晒后的颜色,茶色Electricfitting电装、Rubberpad橡胶垫Shockabsorbingrubberstopper减震橡皮塞Dieheight模子闭合高度Diestroke动模行程Intensificationratiostandard增强比标准Plungerstroke柱塞行程Plungertippenetration冲头穿透力InletMortarManifold总管,集合管Clampforcesensor夹紧力传感器Attenuate削弱Emulsification乳化作用中子线??wireforsliding出模斜度draftangle隔皮bur掉肉misrun研配grindTurbidity浑浊度Refractmeter折光仪Sediment沉淀物GlycolDroolingLithiumSlantCoreslidingface型芯滑面Fluxtreatment熔剂处理Dieclampingcylinder模具夹紧气缸Clogging堵塞，闭合Electrodebar电极棒Fumigationcertificate熏蒸消毒证书Crate条板箱，柳条箱Resinparts树脂零件Oilring油环Gearbox齿轮箱，传动箱,变速箱Draftangle出模斜度Tapanddrillgauge丝锥及钻头规TapborerRackTubes油缸CupSealsFeedPipes输油管Spools卷轴RecuperatingSeal(恢复性密封) InflatorTubes充气. CutSealsSteeringHoses转向胶管Biscuitthickness料柄厚度注油孔oilfilterpoint牛皮纸kraft/brownpaper瓦楞纸flutingpaper崩料chargedownslide/collapse 卡涉现象interferencephenomenon复制模偏心距抽大缸料头抽芯WrenchStopperCheckvalve止回阀Orifice孔，口Pilotvalve领示阀，导阀Coldshut冷疤，冷结Flowmark波纹，流线谱Surgepressure冲击压力，脉动压力Jackbolt定位螺栓Anchorhole锚栓孔Dustseal档尘圈Valvecover气门盖，阀盖Cylindertube汽缸筒AirhoseAtomizerStrainerShaftPulley滑车，滑轮Springwasher弹簧垫圈Inverter电源交换器Cuttingfluid切削液refractioncoefficient折光系数pluggauge塞规colorshade色泽redleadpower红丹粉stressrelief去应力castingfilm铸型薄膜castform铸造成形,铸型castingsealer铸件渗补剂castingstrain铸造应变castingstress铸造应力sparkplug火花塞internal-combustionenginecylinder内燃机汽缸pinion小齿轮pinionbearing小齿轮轴承pinioncage主动[行星]齿轮架,差速器壳,差速盘pinioncuttingmachine齿轴切削机床pinionhead齿轴齿顶pinionshapedcutter插齿刀valvecock阀栓valvecottar气阀制销valvedisc阀盘valvedischargecentrifuge活门卸料式离心机valvefollower阀推杆分层Delaminationfilling-engine梳丝机器fillingagent填充剂;填料fillingauger装载螺旋fillingcompoun填料fillingfunnel注液漏斗车架钣金测板内侧板焊钳焊条焊点前轴后翼子板切削性能cuttingcharacteristic散热性能heatdispersion耐磨性能wearresistantproperty摩擦系数frictioncoefficient灰铸铁grayiron;graphiticcastiron缸套cylinder,sleeve,barreltubepipe 导轨面guideway(face)铣刀盘facemillingcutter/facingcutter 刀盘toolpan/cutterhead磨削余量grindingallowance耐用性endurance钝化刀尖圆弧(刀具)燃烧室磨屑滤器芯差速器废气涡轮增压盲区turboloch喷油器oilsprayer/atomizer汽化器carburetor硬质合金刀具carbidetippedtool精镗刀具fineboringtoolspanner扳子(美作:wrench)double-endedspanner双头扳子adjustablespanner,monkeywrench活扳子,活络扳手boxspanner管钳子(美作:socketwrenchcalipers卡规pincers,tongs夹钳punchscraperreamerhacksawoilcan边刨床插床slottingmachine车刀lathetool车轮车床carwheellathe车削turningBayonet卡口Bearingprocessingequipment轴承加工机Beltdrive带传动Bendingmachines弯曲机Boringheads搪孔头Boringmachines镗床Cablemakingtools造线机CNCtoolingsCNC刀杆CNCwire-cuttingmachines电脑数控线切削机Conveyingchains输送链Crimpingtools卷边工具Disposabletoolholderbits舍弃式刀头Etchingmachines蚀刻机Honingmachines搪磨机Lappingmachines精研机Millingheads铣头Moldpolishing/texturing模具打磨/磨纹Planingmachines刨床bankmarkbiteblisterbloomingblowholeblushingbreaking-in冒口带肉bubble膜泡burnmark糊斑burr毛边camber翘曲centrebuckle表面中部波皱check细裂痕checking龟裂chipping修整表面缺陷clamp-off铸件凹痕collapse塌陷crackcrazingcrazingedgefadingfissureflangewrinkle凸缘起皱flaw刮伤flowmark流痕galling毛边glazing光滑greasepits污斑grindingdefect磨痕haircrack发裂haze雾度incrustation水锈indentation压痕mismatchmottleneckingnickoverflowpeelingpit坑pock麻点pockmark痘斑resinstreak树脂流纹resinwear树脂脱落riding凹陷sagging松垂saponification皂化scar疤痕scrapjam废料阻塞scratch刮伤/划痕scuffing深冲表面划伤seam裂痕sinkmarkstreaksurgingsweatouttorsion扭曲warpage翘曲waviness波痕webbing熔塌weldmark焊痕whitening白化wrinkle皱纹表面处理关联用语时效硬化agehardening气体硬化airhardening空气韧化airpatterning退火阳极效应滚镀滚筒打光染黑法青熟脆性箱位退火封箱渗碳辉面电镀光辉热处理brightheattreatment 旁路热处理bypassheattreatment 化学电镀chemicalplating化学蒸镀chemicalvapordeposition 大气热处理controlledatmosphere 锐角效应cornereffect儒缓放电creepingdischarge 压花embossing部分淬火selectivequenching。

常用铸造术语中英对照2021-6-26整理(BY BARRY)Ⅰ.根本术语1.压力铸造die casting2.铸造casting,foundry,founding3.铸件casting4.毛坯铸件rough casting5.试制铸件pilot casting6.试模trial shot7.模具mold,mould8.压铸机die casting machine9.铸造设备foundry equipment,foundry facilities10.铸工caster,founder,foundry worker11.压铸工die carter12.铸造厂foundry13.铸造车间foundry shop14.铸造工作者foundry man15.批〔batch一批:a batch;每批:each batch, per batch);lot16.一炉a cast,a heat,a melt17.焊接welding18.铸造三废foundry effluent19.铸锭ingotⅡ.铸造合金、熔炼和浇注1.铸造合金cast alloy2.铝合金aluminium alloy3.铸造复合材料cast composite4.合金元素alloy element5.杂质元素tramp element6.碳化物carbide7.过热superheating8.过冷supercooling9.熔点melting point10.总碳量total carbon11.碳当量carbon equivalent12.碳当量仪eutectometer13.铝硅合金aluminium-silicon alloy14.压铸合金die cast alloy15.压铸铝合金aluminium diecast alloy16.压铸镁合金magnesium diecast alloy17.熔炼smelting18.熔化率melting rate19.元素增加gain of element20.熔剂flux21.熔池bath22.除气熔剂degassing flux23.覆盖剂covering flux24.炉料charging25.金属炉料metallic charging26.回炉料foundry returns 27.废金属料scrap28.熔渣slag29.沉渣sludge30.浮渣dross,scum,cinder31.造渣slag forming32.出渣deslagging33.出渣口slag hole34.炉衬furnace liner35.出炉口tap hole36.出炉温度tapping temperature37.重熔remelting38.坩埚炉crucible furnace39.保温炉holding furnace40.精炼refining41.真空精炼vacuum refining42.除气degassing43.残料heel44.浇注pouring45.自动浇注装置automatic pouring device46.浇包，料斗(勺)ladle47.转运包transfer ladle48.金属残液heel49.冷金属cold matelⅢ铸造工艺与工艺设备die casting process and process device1.铸造性能castability2.流动性fluidity3.充型能力mold-filling capacity4.充型速度(浇注速度)pouring rate;delivery rate5.充型时间filling time6.浇注温度pouring temperature7.比浇注速度specific pouring rate8.浇注时间pouring time9.凝固solidification10.凝固时间solidification11.收缩contraction;shrinkage12.收缩率shrinkage13.液态收缩liquid contraction14.凝固收缩solidification contraction15.固态收缩solid contraction16.液-固收缩liquid-solid contraction17.自由收缩free contraction18.收缩余量shrinkage allowance19.收缩应力contraction stress20.热应力thermal stress21.铸造应力casting stress22.残留应力(剩余应力)residual stress23.热裂倾向性tendency to hot tearing24.铸造工艺设计casting process design25.铸造工艺计算机辅助设计Computer-aided design for the casting process;casting process CAD26.实体造型constructive solid geometry;solid modeling27.充型分析mold filling analysis28.铸造工艺设备设计foundry tools design29.铸造工艺卡casting process card;foundry process card30.铸型装配图mold assembly drawing31.铸件图(毛坯图)drawing of rough casting32.铸造工艺准备preparation of casting technique33.铸件设计casting design34.铸件基准面reference face for machining of casting35.分型面parting face;(mold joint;mold parting)36.不平分型面irregular parting;(irregular joint;match parting)37.阶梯分型面stepped parting;stepped joint38.浇注位置pouring position39.交接壁intersection40.十字交接X-junction41.圆角fillet42.热节(点)hot spot43.加强筋stiffening ribs44.拨模斜度draft45.型腔mold cavity46.工艺孔technological hole47.浇注系统gating system;running system48.直浇道sprue49.横浇道runner50.内浇口ingate,gate51.溢流槽overflow well52.排气槽air vent53.分流锥sprue spreader;spreaderⅣ压力铸造〔特种铸造〕die-casting1.压铸机die casting machine2.冷室压铸机cold chamber die casting machine3.冷室卧式压铸机(卧式压铸机)horizontal(cold chamber)die casting machine4.冷室立式压铸机〔立式压铸机〕vertical(cold chamber)die casting machine5.热室压铸机hot chamber die casting machine6.真空压铸evacuated die casting;vacuum die casting7.压射injection;shot8.压射机构injection system9.压室injection chamber10.压射冲头injection ram;plunger11.压射速度injection speed12.压射比压injection pressure13.增压pressurization 14.充填率rate of filling15.锁型(合型)die locking16.合型机构(锁型机构)die closing mechanism17.锁型力die locking force;clamping force18.拉杆tie bar;tie rod19.压铸模die;die casting die20.定模(定型)fixed die;cover die half21.动模(动型)moving die;ejection die half22.浇口套sprue bush23.留型时间opening time24.顶出机构ejection mechanism25.顶杆ejector pin26.抽芯机构core puller27.余料biscuit;slug28.压铸涂料coating of diecasting;releaseagent29.充型压力mold filling pressure30.充型速度filling speed31.保压压力dwell pressure32.保压时间dwell timeⅤ压铸后加工及其工具1.喷砂清理sand blasting cleaning2.喷丸清理shot blasting cleaning3.抛丸清理wheel blasting cleaning4.滚筒清理tumbling5.抛丸清理机wheel blasting machine6.除浇口degating;trimming7.除毛刺deburring8.去氧化皮descaling9.打磨grinding10.弹丸shot11.抛丸器shot wheel12.喷丸器shot blaster13.砂轮机grinder14.浸渗处理impregnantion15.浸渗剂impregnant16.矫型rectification;straightening coining;17.外表处理surface treatment18.砂带打磨belt sanding19.钻孔;镗孔boring20.脱脂degreasing21.电镀electroplating;electrostatic coating22.夹具clamp;fixture23.机加工machining24.铣milling25.台式铣床bench milling machine26.数控加工中心CNC27.铸件机加工余量machining allowance of casting28.切削液mineral cutting oil29.抛光polishing30.粗加工rough working31.喷涂painting32.冲孔punching33.外表处理surface treatment34.洗净rinse35.车床lathe36.磨床grinder,grinding machine37.铣床milling machine38.钻床drill press39.刨床planerⅥ检测方式/设备/工具量具inspection equipment/facility1.合格质量水平acceptable quality level(AQL)2.气密性试验air tightness test3.大气暴露试验atmospheric corrosion test4.成分分析试验chemical analysis5.破坏性检测destructive inspection6.非破坏性检测nondestructive inspection7.尺寸检测dimensional test8.硬度试验hardness test9.冲击试验impact test10.逐件检查individual check11.抽样检查sampling inspection12.三座标检测microcode13.耐压试验pressure test14.盐雾试验salt spray test15.盐雾试验机salt spray test machine16.拉力测量机tensile test machine17.平面度检测仪flatness inspection guage18.检漏机leakage test machine19.普通检具normal guage20.抽样检查sampling inspection21.耐气候试验weathering test22.x光探伤x-ray test23.X光机X-ray machine24.塞规plug guage25.丝攻screw tap26.锥度规conical guage27.螺纹塞规thread plug guage28.游标卡尺vernier caliper29.半径规radius guage30.测角器/量角器bevel guage31.测径规,厚簿规calliper guage32.高度尺height guage33.深度尺depth guage34.三座标CMM35.光谱仪spectrographⅦ.包装packaging1.护边edge protection2.中间夹层intermediate layer3.多插入口式托盘multiple-entry pallet4.一次性托盘throw-away pallet5.耐气候wether resistanceⅧ图纸相关Drawing Related1.喷砂清理abrasive cleaning2.研磨剂abrasive3.依据according to/Acc to4.阳极氧化anodic oxidation5.外观appearance6.踏板autowalk pallet7.底座基座基准base8.盲孔blind hole9.气孔,气泡blow hole10.孔径hole diameter11.凸台boss12.基准面datum plane13.模定位面cast locator datum plane14.铸造应变casting strain15.中心孔center bore16.外圆角,倒角chamfer17.内圆角fillet18.同心度concentricity19.平面度flatness20.平行度parallel21.粗糙度roughness22.垂直度perpendicularity23.清洁度cleanness24.符合conform to25.残留物，污物contamination26.抽芯孔,铸孔core hole27.耐腐蚀corrosion resistance28.沉孔counterbore29.盖板cover30.关键尺寸critical dimension31.横切试验cross-cut test32.脱炭decarburize33.拔模斜度draft angle/draft34.导电性electric conductivity35.电动扶梯梯级escalator step36.外径〔大径〕external diameter37.内径(小径)internal diameter38.外螺纹external thread39.加工余量machining allowance40.法兰flange41.披锋flash42.自由状态free state43.通用公差〔未注公差〕general tolerance44.符合in accondance with45.来料检验incoming inspection46.标识indication,marking47.绝缘性isolation characteristics48.金属互化物intermetallic compound49.内螺纹internal thread50.每per51.边缘periphery52.永久伸长permanent stretch53.垂直于perpendicular to54.针孔，销孔pin hole55.平面图plan,plane figure56.磨光剂polish agent57.聚酯纤维polyester58.容许应力proof stress59.剩余应力residual stress60.试生产铸件prototype casting61.质量保证quality assurance62.散热器radiator63.耐磨性resistance to abrasion64.肋；筋条rib65.滚丝攻通roll thread thru66.剖面图section67.模具寿命service life of dies68.螺距pitch69.阴影毛坯区域shaded area cast70.收缩shrink71.缩孔shrinkage porosity72.碎片sliver73.烧伤soldering mark74.标准standard/std.75.强度范围strength division76.分层;剥落stripped mark;peeling77.清理外表;外表加工;外表抛光surface finish78.抗拉强度tensile strength79.未注unless otherwise specified/unspecified/unmarked80.凸纹/直纹vein grain81.壁厚wall thickness82.屈服点yield pointⅨ压铸报价Quotation1.适用检测标准acceptable inspection standard2.压铸附加费additional casting cost3.铸造费用casting cost4.折扣价depreciation expenses5.估价estimated price6.离岸价free on board(FOB)7.到岸价cost insurance freight(CIF)8.信用证letter of credit(LC)9.后加工费finishing cost10.定率法fixed rate method11.先行生产go-ahead of produce 12.铝锭价格ingot price13.插件费insert cost14.检测费inspection cost15.熔炼费melting cost16.制造间接(额外)费overhead manufacturing expense17.附加利益profit added18.废品比例rejection percentage19.废品率standard rejection rate20.报废时价值,剩余价值,剩余价值residual value/scrap value21.机器运转费;机器运营本钱running cost of machine22.卖价selling expense23.销售间接费selling overhead24.寿命service life25.(合金)掺合比例standard alloying ratio26.标准价格standard price27.试铸时间time of trial shot28.总价格total cost29.试铸费trial casting cost30.除浇口费trimming cost31.生产yield32.生产率yield rate33.后加工合格率yield rate of finishing34.熔炼生产率yield rate of melting35.压铸成品率overall yield of castingⅩ压铸质量和缺陷casting quality and defect1.废品reject2.化学成分不合格chemical consistenceabnormal3.飞边joint flash4.毛刺veining;burr5.气孔blowhole6.气泡blister7.气泡bubble8.激冷区chill zone9.冷脆性cold shortness10.冷隔cold shut;cold filling11.裂纹crack12.铸点dot13.花纹flower msrk;stripping for shot blast14.外部材料foreign material。

广东文灿压铸有限公司Wencan die casting Co., Ltd常用英语术语列表List of die casting terms and vocabularies( 2011-9-23 re-edit V6)1.新产品以及模具开发products and tooling developing2D/3D drawing 平面图/3维图bump among products 货与货之间碰撞capital equipment 资本设备, 固定设备chamfering倒角classification 分类、级别datums 基准datum level 基准水平面datum line 基准线datumplane 【测】基(准)面design/process FMEA D设计/P过程FMEAdie casting 压铸die fabrication 模具加工Die location layout 工模排位图Die polished 省模Die trial 试模electrode for EDM 放电用铜公machining by CNC wire-cut machine 线切割加工machining by electric discharge machine ( EDM ) 电蚀火花加工potential effects of failure 潜在失效后果potential failure mode 潜在失效模式rib and corner 筋肋和尖角subcontractor 外包商set die-casting parameter/locking force/ injection force/injection velocity/shot time/ volume of release agent/die-open time/ ejector time/pressure rating/metal temperature/ control temperature/ operation according to WI按工作指示设定压铸参数/锁模力/射料力/射料速度/打锤时间/喷雾量/开模时间/顶出时间/压力参数/料温/控制温度/按照作业指导书作业；thermal expansion 热膨胀2．热处理heat treatmentair cooling 空气冷却annealing 退火carbonization 碳化case hardening 表面硬化，表面淬硬full annealing 完全退火heat treatment 热处理metallographic structure 金相组织metallographic test 金相试验quenching 淬火residual stress 残余应力tempering 回火3．压铸设备及模具die casting machine and die toolingangle pin 斜导销biscuit /slug 料饼/余料blister 气泡burner 燃烧器casting area最大压铸面积casting insert 铸件镶件casting fin铸件飞边, 铸件披缝, 铸件周缘翅片cavity fill time 充型时间cavity insert 型腔镶块cavity 型腔center furnace 中央熔炉clamp force max. 最大压力coefficient 系数cold chamber machine 冷压室压铸机cold/hot chamber pressure die-casting machine 冷/热室压铸机contraction 收缩core slides/core 活动抽芯（型芯）cover die half(stationary half )/ ejector die half (moveable half ) 前（定）模/后（动）模crucible furnace 坩埚炉crucible pot 坩埚degassing 除气/去气delivery rate；pouring rate 充型流速/浇注速度design of gating system 浇注系统设计die layout模具排位图die life 模具寿命die stroke 开模行程draft 拔模斜度ejector force顶出力ejector pad 顶针痕ejector pin 顶针ejector stroke 顶出行程feeding 补缩foundry returns 回炉料gating/running system 浇注系统holding furnace 保温炉ingate 内浇道injection plunger 压射冲头ladle 浇包locking force 锁模力machine platen 压铸机模板moving/fixed platen 动/定模板maximum/minimum die height 最大/最小压模厚度metal fluidity （金属）流动性molten metal 熔化金属nitrogen pressure 氮气压力normal pressure工作压力numerical simulation of casting solidification 铸件凝固数值模拟opening time 留型时间/开型时间overflow 溢流槽/ 渣包production die 量产模prototype die 样板模refining 精炼refining agent 精炼剂remelting 重熔riser/feeder head 冒口runner 横浇道runner/gate 流道/浇口scrap 废金属料secondary alloy 再生合金shot sleeve 司筒,压射室size of die platen 模板尺寸slag 熔/炉渣sludge/dross 沉/浮渣solidification 凝固sprue pin（spreader）直浇道锥（分流器）spure 直浇道die frame 模架tangential runner 切向横浇道tie bar 哥林柱/导柱/拉杆total melting loss 熔炼损耗率熔损、烧损trim die 冲模vent 排气口water cooling channel 冷却水通道4．压铸工艺与后加工工艺die casting and secondary process alloy component assay report 合金成份化验报告appearance外观center furnace 中央溶炉characteristics 特性degating 冲水口die casting 压铸parting line 分型线polishing/buffing 磨/抛光polishing 抛光、磨光polishing/cotton wheels 抛光用布轮removing burrs round pads of ejector pin 刮项针位批锋removing parting line flash 磨分型线sanding wheels 砂布轮5．精加工工艺machining processboring 镗精加工fine maching ; 粗加工rough maching drill bit 钻头卧式加工中心Horizontal machining center chuck 车床卡盘，夹具立式加工中心vertical machining center cutting tools刀具external/internal thread 外/内螺纹file 锉form tool 成型刀grind 磨jig/fixture 夹具lathe 车床left-hand thread左旋螺纹length of thread engagement螺纹旋合长度loose thread滑牙machining accuracy加工精度machining allowance of casting 铸件机械加工余量machining allowance加工余量machining error加工误差mandrel 机加工芯轴mill 铣minor diameter小径parallel screw thread圆柱螺纹pitch diameter中径pitch螺距plane 刨,Reaming铰孔right-hand thread 右旋螺纹rolled threads 挤牙root diameter底径screw thread 螺纹tapping 攻牙tight thread牙紧uncompleted tapping 牙不完整6．表面处理surface treatmenta mixture of 2 parts water and 3 parts oil 2分水3分油混合acid dip/pickling 酸洗acid 酸水alkali cleaning 碱洗Anodizing 阳极氧化baking 烘干blueing /chemical oxide 钢铁发蓝/化学氧化chemical pretreatment 化成处理chromating 铬化clear black e-coatings透明黑色泳漆clear chroming 无色铬化colored passivation 彩色钝化concentration 浓度dedusting 除尘degreasing 脱脂，除油descaling 刻蚀dipping 浸渍electrophoresis 电泳electrophoretic coating 电泳漆electroplating hard chrome 镀硬铬electrostatics powder coatings 静电粉沫喷涂E-plating 电镀hexavalent chromium 六价铬impregnation 浸渗mechanical polishing机械抛光neutralization 中和PAD printing/silk screening 移印/丝印passivating 钝化phosphating 磷化resin 树脂rinsing 过清水Roughtening 粗化spray powder 喷粉taking down 下挂trivalent chromium 三价铬ultrasonic clean 超声波清洗wiping with toluene 抹天那水salt spray testing 盐雾试验7．品质控制quality controlappearance full-inspection 外观全检collection 回收evaluation / measurement technique 评价/测量技术first inspection for 5 shots 首检5件Freq=frequency 次数incoming quality sampling inspection report 来料质量抽查报告interprocess quality sampling inspection report 工序间质量抽查报告pile products up due to laying in disorder 摆放不正确堆积产品processing tour-inspection 制程巡回检查product/process specification /tolerance 产品/过程规范/公差projector 投影仪QC tour-inspection QC巡检quality final-inspection report 最终检验质量报告quality first piece inspection report 质量首件检查报告quality traceability analysis report 质量追踪分析表return to supplier 退回供应商sampling inspection 抽检self-inspection 自检Special Char. class 特殊特性分类spot check 抽样检查visual standard 外观标准workmanship standard 工作质量标准8.质量缺陷常用语defectsair tightness 气密性blister/pimple/bubble 起泡bumps 碰伤caniniform/dentate狗牙casting fin铸件飞边, 铸件披缝, 铸件周缘翅片cold lap 冷隔cold shut 冷纹Contamination 污染dirt pits 尘点distortion/deformation 变形double skin 重皮ejector marks raised or depressed 顶针位凹凸elephant skin皱皮entrapped slag；slag inclusion 夹渣filling to excess 多料flow mark 流痕/波纹flow lineincomplete filling 缺料incorrect casting form 形状不合格indentation 印痕/凹痕internal quality of casting 铸件内在质量micro-shrinkage；porosity 疏松【显微疏松】off dimension；off size 尺寸不合格oil marks 油渍orange peel 桔皮缺陷out of size 尺寸不符oxidation 氧化partial breakage of a casting 崩料peeling 电镀脱皮pinhole针孔pits 面麻porosity 砂孔roughness 粗糙sand inclusion 砂眼scratches 划痕/刮伤shrinkage 缩水slag 炉渣stain 污渍texturing 致密性thermal shrinkage crack （on product）(产品中的)热缩裂raised crack mark line (on product) (产品表面凸起的龟裂线) visual quality of casting 铸件外观质量void 砂眼/气孔warpage 挠曲yellowing发黄yield of casting 铸件合格品率missrun 欠铸9. 压铸件试验常用语testingadhesion 附着性deflection 挠度elastoplasticity 弹塑性elongation 延伸率extend 延伸film thickness 涂膜厚度film thickness gauge 膜厚仪flexibility 屈曲挠性hardness 硬度heat impact test 热冲击试验high humidity test 高湿测试humidity resistance 耐湿impact resistance 抗冲击力impact strength 冲击性measuring adhesion by tape test 胶带附着力测试neutral salt-spray NSS test 中性盐雾residual stress 残余应力spraying viscosity 喷涂粘度strengthen 加强、巩固tension 拉紧、张力viscosity 粘度water resistance 耐水性yield strength 屈服强度mechanical property 力学性能chemical analysis 化学成份10.测量工具常用语measurement and gauge Altitude gauge 高度仪average 平均值Block Gauge 块规Bore Gauge 孔规Clearance gauge 塞尺/间隙规CMM 三坐标测试仪Depth Micrometer 深度千分尺Digital caliper 电子卡尺Digital Height Gauge 数字高度测量仪durometer/hardness meter 硬度计Electric/digital Balance 电子称Electroplating THK.Tester 电镀厚度测试仪equipment variation 设备变差gage repeatability and reproducibility report 量具的R&R重复性和再现性报告go-no-go gauge “过” -- “不过” 验规通-止规HRC/HV Hardness Tester 洛/维氏硬度仪Rockwell testingimpact tester 冲击仪Inside/outer Micrometer 内/外径千分尺measurement unit analysis 测量设备分析Micrometer Calipers 千分卡尺Microscope 显微镜metallographic microscope 金相显微镜Multimeter 万用表electric universal testing 电子万能试验机normal distribution curve 正态分布曲线number of parts 零件数量number of trials 实验次数one range 单极差part variation 零件变差pin gauge 针规Plug gage 塞规Projector 投影仪Optical image 光学影像测量仪range 公差带range control chart 极差控制图repeatability 重复性reproducibility再现性Ring Gauge 环规spectrometer 光谱仪Thermometer 温度计Thread Gauge 螺纹规thread plug gage螺纹塞规Torque Meter 力矩计total variation 总变差Twisting Meter 转扭力仪Vernier Caliper 游标卡尺viscosimeter 粘度计visual check 目测witness mark (测量)参考(标)点endoscope 内窥镜11. 形位公差常用语toleranceangularity 倾斜度角度aperture 孔径basic dimension 基本尺寸basic size 基本尺寸c/c =between centers 中心距centricity中心circular runout 圆跳动circularity 圆度roundnessconcentricity 同轴度同心度conical 圆锥形的coordinate data 坐标数据coordinate dimensioning 坐标尺寸cylindricity 圆柱度datum/feature/point/line/ plane/axis 基准/特征/点/线/平面/轴线deviation偏差diameter/radius 直径/半径draft angle 拔模斜度ellipse 椭圆excentricity 偏心距（率）flatness 平面度geometric dimensioning 几何尺寸fit/clearance fit/interference fit/ transition fits 配合/间隙配合/过盈配合/过渡配合M/LMC=maximum/least material condition 最大/小材料状态nominal diameter 公称直径oblong 长方形oblong hole 椭圆孔ovality 圆锥度（变形）parallelism 平行度perpendicularity 垂直度position 位置度profile of a line 线轮廓度profile of a surface 面轮廓度reference frame 坐标系right angle 直角rounds/fillets draft 外圆角/内圆角拔模斜度square 正方形standard/ precision tolerance 标准/精度公差straightness 直线度symmetry 对称度theoretical size 理论正确尺寸thickness厚度tolerance/value 公差/值top/side/ end view 顶/测/端视图total runout 全跳动unilateral/bilateral tolerance 单/双边公差upper/lower deviation 上/下偏差12.包装和包装材料packagebar code 条形码blister plate/PVC tray 吸塑罩bubble bag 气泡袋closed /sealed poly bag 封口胶袋corrugated cardboard/sheet波纹隔板corrugated egg-crate carton 瓦楞蛋格卡通箱foam bag 珍珠棉袋forktruck 叉车GW gross weight /NW net weight 毛/凈重If wooden pallet, the certificate of disinfection for pallet 如果是木制卡板要有卡板消毒熏蒸证明in egg tray with carton packages 卡通箱及其蛋格item/ sales consumer pack 单件装label 包装标识logo polybag 有唛胶袋multipack 多件装outside dimensions 长x宽x高length x width x height 外部尺寸packaging materials 包装材料packaging strapping/PP-straps包装带pad separator; clapboard; partition board/sheet 隔板pallet 卡板plastic container 胶箱shrinkage package 吸塑包装single/double/3 regular slotted carton/box 单/双/三坑纸箱styrofoam 聚苯乙烯泡沫塑料白色泡沫tissue papper 拷贝纸transparent plastic film circle the pallet/stretch poly wrap 透明膜保鲜纸unitload pallet 整卡装wrappage 包装材料13.生产控制计划production controlcontrol plan 控制计划core team 核心小组date Rev. 日期修订date orig. 日期编制each batch 每批Inform line/team leader/ supervisor/manager to shut down and recheck 通知生产拉/组长/主管/经理，停机再检查machine adjustment 调机machine, device, jig, tools for Mfg. 生产工艺装备material identification 物料标识mounting die 安装模具mounting die inspection sheet 模具安装检查清单once every operation每次开机part /process number 零件/过程编号part name/description 零件名称/描述pre-launch 试生产process 过程process name/operation description 过程名称/操作描述reaction plan 反应计划refer to CP 参考控制计划14.优质浇口设计七步法gate design优质浇口设计七步法The Seven Steps To A Quality Gating Design第一步确定铸件质量等级。

铸造行业英语词汇大全：一、铸造基本术语1. Casting：铸件2. Pattern：模样3. Mold：模具4. Core：砂芯5. Sand：砂子6. Foundry：铸造厂7. Melting：熔炼8. Pouring：浇注9. Solidification：凝固10. Casting Defects：铸件缺陷11. Machining：机械加工12. Inspection：检验二、铸造材料1. Grey Cast Iron：灰铸铁2. Ductile Cast Iron：球墨铸铁3. White Cast Iron：白铸铁4. Highstrength Cast Iron：高强度铸铁5. Stainless Cast Steel：不锈钢铸件6. Carbon Steel：碳钢7. Alloy Steel：合金钢8. Titanium Alloy：钛合金9. Aluminum Alloy：铝合金10. Copper Alloy：铜合金11. Magnesium Alloy：镁合金三、铸造工艺1. Sand Casting：砂型铸造2. Investment Casting：熔模铸造3. Die Casting：压铸4. Centrifugal Casting：离心铸造5. Continuous Casting：连续铸造6. Squeeze Casting：挤压铸造7. Lost Foam Casting：消失模铸造8. Shell Mold Casting：壳型铸造9. Vprocess Casting：V法铸造10. Highpressure Die Casting：高压铸造四、铸造设备1. Melting Furnace：熔炼炉2. Pouring Machine：浇注机3. Sand Mixer：砂混合机4. Molding Machine：造型机5. Core Shooter：射芯机6. Shakeout Machine：落砂机7. Grinding Machine：磨削机8. Shot Blasting Machine：喷砂机9. Testing Equipment：检测设备10. Robot：机器人五、铸造缺陷1. Blowhole：气孔2. Sand inclusion：砂眼3. Porosity：缩孔4. Shrinkage：缩松5. Cold shut：冷隔6. Hot tear：热裂7. Overfeed：过补给8. Underfeed：欠补给9. Oxidation：氧化10. Incomplete fusion：熔接不良六、铸造技术参数1. Tolerance：公差2. Draft：拔模斜度3. Parting Line：分模线4. Riser：冒口5. Gate：浇道6. Runner：滑道7. Cooling Time：冷却时间8. Solidification Time：凝固时间9. Molding Sand Properties：型砂性能10. Core Sand Properties：芯砂性能七、环保与安全1. Environmental Protection：环保2. Waste Gas Treatment：废气处理3. Waste Water Treatment：废水处理4. Solid Waste Treatment：固体废物处理5. Dust Collection：除尘6. Safety：安全7. Personal Protective Equipment：个人防护装备8. Fire Protection：消防9. Occupational Health：职业健康10. Accident Prevention：事故预防八、国际合作与标准1. ISO：国际标准化组织2. ASTM：美国材料与试验协会3. DIN：德国工业标准4. JIS：日本工业标准5. BS：英国标准6. SAE：美国汽车工程师协会7. International Foundry Research：国际铸造研究8. Foundry Technology Transfer：铸造技术转移9. Import and Export：进出口10. Global Foundry Industry：全球铸造行业。