迅雷科技一键遥控自动关窗器升窗器安装实例说明书 K3豪华(普通)

1-Button Remote 2-Button Remote 3-Button RemoteModel LK-318-1Model LK-318-2Model LK-318-31-Button Transmitter LK-318-12-Button TransmitterLK-318-23-Button Transmitter LK-318-3ButtonsRed LED Thank you for your purchase of a SkylinkHome TM Remote, Model LK-318-1/ LK-318-2 / LK-318-3. This remote which is also called transmitter in this document allows you to wirelessly operate SkylinkHome TM receiver modules.All wireless signal communications within the SkylinkHome TM system are based on rolling code technology to ensure highest security is used. The following items are included in this package:- One of LK Series Remotes- Lithium Battery CR-2032 (Installed)- User’s Instructions2. POWER UPTo power the transmitter, simply remove the battery isolator from the transmitter, red LED will flash once. Press the button on the transmitter, the red LED should flash. The transmitter is now powered properly. If the red LED does not flash when button is pressed, refer to Section 6 “Battery” of this manual.1) Remove isolator, 2) LED on for 1 secondIn order to operate the receiver module remotely with a transmitter, it must be programmed to the receiver module.To program a remote to the receiver module, a “Learn” code must be transmitted, follow the instructions below to transmit the “Learn” code to the receiver.1. Put the receiver module that you plan to program into programming mode. Refer to the User’s Instructions of that receiver module.2. Press 1 and 2 simultaneously and hold for 2 seconds until the LED changes from on to flashing quickly. Release the buttons. The red LED on the transmitter will be on for 15 seconds.3. Press the button on the remote that you plan to use when the LED is steadily on to transmit the “Learn” code.4. Once the remote is programmed, the receiver modules will quit from programming mode and the programmed transmitter is ready to be used now. Learn CodeFollow steps 2 and 3 above to transmit the “Learn” code when programming the remote to receiver modules.You may follow the same instructions to program different buttons on the transmitter to different receiver modules.LED on for 1 secondPressing the programmed button on the transmitter once will toggle the status of the load that is connected to the receiver module, i.e. if the light is off, pressing the button turns on the light, and vice versa. When the programmed button is pressed, the red LED flashes briefly indicating signal is transmitting.Password protection (Only available for LK-318-3 (Not available for LK-318-1 or LK-318-2)The LK-318-3 can be password protected. If you enable the password protection, you can only operate LK-318-3 after you input the correct password.Password can be 2-8 digits long, which is a combination of 1, 2 and 3. For example, password can be 1, 2, 1, 2. To input this password, you have to press button [1], then [2], then [1], then [2].Note:[1] = Button 1 [2] = Button 2 [3] = Button 3Note:The time-out period is 1 second during above password input.The factory default password is 2, 2, 2, and this password function is disabled out of factory.Change password1. Press 1 and 3 simultaneously and hold for more than 10 seconds until the LED changes from flashing quickly to flashing slowly.2. Input old password.3. Press 1 and 3 once simultaneously to confirm. If the password is wrong, the LED will flash 3 times and you have to start it over from step1.4. Input new password.5. Press 1 and 3 once simultaneously to confirm.6. Input new password again.7. Press 1 and 3 once simultaneously to RE-confirm. If the password is different from the one of step 4, the LED will flash 3 times and you have to start over from step 1. Otherwise, the password has been changed to the new one and the password protection is enabled.Disable password1. Press 1 and 3 simultaneously and hold for more than 5 seconds until the LED flashes quickly but not until the LED flashes slowly.2. Input old password.3. Press 1 and 3 once simultaneously to confirm. If the password is the password protection will be disabled.Enable password1. Press 1 and 3 simultaneously and hold for more than 2 seconds until the LED flashes quickly but not until the LED flashes slowly.2. Input old password.3. Press 1 and 3 once simultaneously to confirm. If the password is correct, the password protection will be enabled.You can toggle the two states - password protection enabled or disabled.Note:The time-out period is 15 seconds during any of the above setting opera-tions. After 10 seconds, the LED will flash 3 times and the remote will exit from setting.isolatorButton [1]Button [2]Button [3]If you forget your password and want to reset LK-318-3, follow the steps below:1. Press 1 and 2 simultaneously and hold for more than 15 seconds until the LED flashes.2. After you release 1 and 2, the LED will be turned off and LK-318-3 will be reset. The password will be reset to factory default.After the reset, password protection is removed but the remote can not control any receiver until you reprogram it to receivers you want to control.When the operating range is reduced, or when the red LED does not flash during operation, it is time to replace the battery.The transmitter is powered by a lithium battery CR-2032. Follow the instructions below to replace the battery to the transmitter.1. Undo the two screws on the back of the remote. The bottom case will then come off.2. Take out the old battery.3. Place the new battery in position.4. Close the cover and reinsert two screws.Note: Dispose of old battery promptly and properly.The device is approved by the FCC and it complies with Part 15 of the FCC Rules. Its operation is subject to the following two conditions : 1. This device may not cause harmful interference.2. This device must accept any interference that may cause undesired operation.WARNING:Changes or modifications to this unit not expressly approved by the party responsibleof compliance could void the user’s authority to operate the equipment.If, within one year from date of purchase, this product should become defective (except battery), due to faulty workmanship or materials, it will be repaired or replaced, without charge. Proof of purchase and a Return Authorization are required.If you would like to- find out the up-to-date specifications- know more about features and applications - download documents, i.e. user’s instructions - order Skylink productsor if you have difficulty getting products to work, please:1. visit our FAQ section at , or **********************************,or3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST. Fax (800) 286-1320The SkylinkHome TM System consists of many other devices such as SkylinkHome TM Remotes, Motion Sensor, ON/OFF Wall Switch, Wall Dimmer, Plug-In Dimmer with or without Repeater, Plug-In ON/OFF Control (Outdoor/Indoor), Screw-In Dimmer, ON/OFF/Dimming Control, ON/OFF Control, Smart Button TM Garage Door Control, etc. Please visit Skylink website at for more information.CUSTOMER SERVICE17 Sheard avenue, Brampton, Ontario, Canada L6Y 1J3Email:*********************** P/N. 101Y058Patent Pending© 2012 SKYLINK GROUPELithium battery CR-2032 included. (Positive side up)。

全自动车窗智能控制器功能说明书本智能车窗控制器是在比亚迪F3的基础上开发出来的适用于大部分相似车型的产品，采用了高性能单片机程序控制及大容量（20A）继电器驱动，具有超越的优异功能及安装方便的特点。

一、主要功能概述：1、四门玻璃全自动单键轻触升降；2、四门玻璃到位检测防夹功能；3、遥控关闭所有车窗功能（含天窗触发）；4、遥控锁车后可对四门窗操作锁定防盗；5、遥控多级开启四门车窗散热功能；6、独创门锁强电触发信号功能；7、采用四通道高精密可调阻力检测；8、设置到位检测及延时双重保护功能；9、设置电机堵转时强制切断输出功能；10、内置自恢复超万次双回路保险；11、使用了睡眠程序，使功耗降到最低；12、启用了看门狗技术，确保芯片永远正常运行；二、四门窗控制：1、原车左前总控制器能对四门窗实现智能控制，具体包括：a、四门按键短按0.3秒释放时可实现分别同时对相应的窗玻璃进行自动升（降）到顶（底），到位后自动停止及中途遇到超过设定阻力（可以分别对四门独立调整阻力大小）时自动停止。

在自动升（降）过程中，如果短按0.3秒相应的降（升）按钮即可中止进行中的升（降）过程。

b、四门按键长按（大于0.3秒）时即可实现实时升（降）玻璃，随放随停，可停止于任意位置，如到位后按键还未放开，系统将检测到位后自动切断该回路停止升（降）从而保护升降电机。

c、童锁开关按下后锁定对右前、左后、右后三个门窗的所有操作，同时童锁开关按下后在用遥控锁车时将不再进行自动升窗。

童锁开关复位后即可正常控制。

d、左前门开关在关钥匙后不能对左前玻璃进行升（降）控制，其余三个门按键在关钥匙状态下可以对三个门窗实现单键升（降）到顶（底）控制（此时可以通过按相反操作中止升降动作），此处功能可能会因个别车的差异而会有些反应迟钝或不能实现的现象，属正常。

2、其余三门对其所对应的玻璃维持原车的操作方式不变，实行点动控制，但智能控制器检测到位后会自动切断相对应的电源进行保护电机避免因过流而烧毁。

马3的停车自动升窗器的安装详细说明！！！
上面这张图非常重要就是要把中控锁电源+线找到接到升窗器上，图上有2组线组了吧，一组是接到电机上的，还有一组是直接通到左车门的关锁器上的，看到破皮的这跟【黄加黑的线】就是，把它破皮和升窗器接起来就OK了！，
注意这根【黄加黑线】
然后把升窗器上的一根连接线接到这根线【黄加黑线】上
接上所以接头，把升窗器用双面胶固定好，复位。

可以享受一下自己的动手成功的喜悦了，慢着，还有一道流程要做，就是还要恢复左窗一键升窗和关窗的功能，就是在汽车通电的情况下，按下降窗键大概5秒钟，再按下升窗键5秒钟，这样算是大功告成！！！恭喜各位车友享受自己成功的喜悦吧。

威尔特科技有限公司电动开窗器厂家安装的方式方法主要有三种：水平安装(立面窗)、竖直安装(外平开窗)、仰角安装(用天斜屋顶天窗)。

更多电动开窗器详情欢迎咨询威尔特科技，电动开窗器具体的安装步骤如下：
一、在安装前，先要明白要安装电动开窗器的窗户类型和开启方式，如天窗一般要选用齿条式开窗器和推轴式开窗器，立面窗则一般选用链条式电动开窗器。

二、在明白了窗户类型和开启方式选好匹配的开窗器后，还要检查电动开窗器电压是交流电(220VAC)，还是直流电(24VDC)，只有这样才可避免在接下来调试开窗器的时候发生烧毁现象。

三、准备好安装工具，如电钻、螺丝刀等工具，准备安装。

四、根据开窗器安装说明书上的图示尺寸，用尺和笔准确地标出开窗器窗框固定安装支架和窗扇安装码的螺丝孔位置。

此时，把这些画好的点用电钻打孔并装上开窗器的窗扇安装码。

威尔特科技有限公司
五、把开窗器的链条通过插销与窗扇上的安装码连接上，此时就可把电动开窗器的窗框安装支架准确去拧上螺丝。

六、电动开窗器安装后，接上电源进行调试。

调试主要看开窗器是否安装的牢固，是否能把窗扇关得紧，锁得严，链条是否会碰到窗框，链条抻出是否为一条直线等。

七、如果按照上述操作下来，电动窗启闭自如，则电动开窗器安装合格，链条式电动开窗器安装到此完毕。